飞机维修常用工具中英文对照-分类
飞机常用单词英汉对照
航空英语证书考试(PEC)-航空飞行器词汇Acquisition Time: 初始定位时间Active Leg: 激活航线Adapter: 转接器、拾音器、接合器Airborne: 空运的、空降的、机载的、通过无线电传播的Alkaline: 碱性的、碱性Almanac: 历书、概略星历Anti-Spoofing: 反电子欺骗Artwork: 工艺、工艺图、原图ssAtomic Clock: 原子钟Auto-controlling: 自动控制Avionics: 航空电子工学;电子设备Azimuth: 方位角、方位(从当前位置到目的地的方向)Beacon: 信标Bearing: 方向，方位(从当前位置到目的地的方向) Bug: 故障、缺陷、干扰、雷达位置测定器、窃听器Built-in: 内置的、嵌入的Cellular: 单元的、格网的、蜂窝的、网眼的Cinderella: 水晶鞋、灰姑娘这里特指JA V AD GPS接收机OEM板的选项，能自动在隔周的星期二GPS午夜时刻开始的24小时内让您的Javad接收机和OEM板变为双频双系统。
Coarse Acquisition Code(C/A): 粗捕获码Cold Start: 冷启动Connector: 接头、插头、转接器Constellation: 星座Control Segment: 控制部分Converter: 转换器、交换器、换能器、变频管、变频器、转换反应堆Coordinate: 坐标Co-pilot: 飞机副驾驶Cost-effective: 成本低，收效大的Course: 路线、路程、航线Course Deviation Indicator (CDI): 航线偏航指示Course Made Good (CMG): 从起点到当前位置的方位Course Over Ground (COG): 对地航向Course To Steer(CTS): 到目的地的最佳行驶方向Crosstrack Error (XTE/XTK): 偏航De-emphasis: 去矫、去加重Definition: 清晰度Diagonal: 对角线、斜的、对角线的Distinguishability: 分辨率Dropping resistors: 减压电阻器、将压电阻器Datum: 基准Desired Track (DTK): 期望航线(从起点到终点的路线)Differential GPS (DGPS): 差分GPSDilution of Precision (DOP): 精度衰减因子Elevation: 海拔、标高、高度、仰角、垂直切面、正观图manned flight 有人驾驶的飞机aerodynamics 空气动力学cambered surface 弧面，弯曲面characteristic 性能，特性drawing 图纸glider 滑翔机lift 升力model 模型，样机structure 结构，构造transportation 运输；运输工具wing 机翼biplane 双翼机control v. 操纵，控制，驾驶rib 肋，翼肋cloth fabric 布织物lifting surface 升力面girder 桁架，构架，机架，骨架bamboo 竹材strip 带状物，狭片，长条，简易机场，跑道piano wire 钢琴丝auxiliary surface 辅助翼面stability 安定性，稳定性configuration 外形，形状，结构，构造型式，布局truss type structure 桁架式结构strut 支柱，支撑wire-braced wing 张线支撑的机翼cockpit 飞机驾驶舱fabric-covered body 织物覆盖的机体fuselage 机身engine 引擎，发动机tail 尾部strong lightweight structure 坚固的轻型结构resistance 反抗，抵抗，阻力，阻尼，电阻friction 摩擦，摩擦力potential speed 潜在速度strength 强度plane 飞机designer 设计者superstructure 上层结构，上部结构wooden former 木质翼肋，木质隔框stringer 桁条，长桁smooth streamline shape 光滑流线型welded thin-wall steel tubing 焊接的薄壁钢管stressed-skin structure 承力蒙皮结构plywood eggshell-like structure 层板薄壳式结构laminated wood ring 层半框架，胶合板框架landing gear 起落架aluminum-alloy sheet 铝合金板monocoque structure 硬壳结构all-metal aircraft 全金属飞机semi-monocoque structure 半硬壳式结构rigidity 刚度structural challenge 结构方面的困难（挑战）high-altitude flight 高空飞行mysterious adj. 神秘的，费解的fatigue 疲劳pressurization and depressurization cycle 增压减压循环fail-safe construction 破损安全结构rip-stop doubler 止裂加强板strategic location 关键部分crack 裂纹structural component 结构部件stress 应力aviation maintenance technician 航空维修技师aircraft structure 飞机结构control surface 操纵面，舵面stabilizer 安定面flap 襟翼trim tab 调整片spoiler 扰流板，阻流板，气流防护板rudder 方向舵attitude 状态，姿态，姿势compression 压缩，压力tension 拉伸，拉里，张力torsion 扭曲，扭转，扭力，扭转bending 弯曲，挠曲shear 剪切，剪力，切变，切力definition 定义，阐明，确定，明确crush v. 压碎，击碎，牙边，挤压press v. 压缩，冲压，挤，推stretch v. 伸展，伸长，拉紧，延伸cable 钢索bolt 螺栓material 材料layer 层，夹层，薄片，条river 铆钉tensile force 拉力overstressing 过度应力，超限应力permanent deformation 永久变形strain v. 硬变，变形，延伸率，过度使用airworthy adj. 适航的，飞行性能好的assembly 组合，装配，总装组件，部件，装配件stress analysis 应力分析performance 性能，特性，行为，表现，实行，实施，完成，操作specification 详细说明，技术规格，技术条件，说明书danger 危险failure 失败，故障，事故，破坏，断裂nomenclature 术语，专用名称aileron 副翼trailing edge 后翼wing tip 机翼翼端roll v. 滚转，横滚，滑跑lifting force 升力jet airplane 喷气式飞机cruise speed 巡航速度approach speed 进场着陆速度，进近速度landing speed 着陆速度，接地速度chord line 弦线angle of incidence 安装角airfoil 翼型，翼剖面，机翼，翼面，气动力面longitudinal axis 纵轴stabilizer setting angle 安定面安装角horizontal stabilizer 水平安定面vertical stabilizer 垂直安定面sweep angle 后掠角reference line 参考线horizontal axis 水平轴线antidrag wire 反阻力张线（承受与飞行阻力相反的惯性力的对角张线）leading edge 前缘antilift wire 反升力张线balanced control surface 平衡操纵面equilibrium 平衡状态hinge axis 铰链轴static condition 静止状态beltframe 连接隔框skin 蒙皮frame 框，隔框，壁板式隔框boom (tailboom) 尾撑,尾梁built-up structure 组合结构，拼装结构cabin 机舱，客舱helicopter 直升机rotor 转子，叶轮，旋翼tail rotor 尾桨power train 动力系列compartment 隔舱，舱，隔间，室former 隔框，翼肋，维型框，假肋cabane 顶架canard 鸭式飞机，鸭式布局，鸭式翼，前置平尾，前舵cantilever beam 悬臂梁external bracing 外部支撑center section 中翼，中段outer wing panel 外翼段passenger 旅客，乘客cabin airplane 闭舱式飞机cockpit canopy 座舱盖，驾驶舱盖control cable 操纵钢索control lever (control stick) 驾驶杆，操纵杆longitudinal control surface 纵向操纵面lateral control surface 横向操纵面，横侧操纵面elevator 升降舵ruddervator 方向升降舵（V型尾翼的）control wheel 驾驶盘semiwheel 半盘式cowling 整流罩，包皮，防护罩removable cover 可卸口盖decalage 翼差角dihedral angle 上反角drag strut 阻力支柱（在布制蒙皮机翼结构中，用以支持阻力张线的加强肋）阻力杆（起落架前拉杆和后撑杆）drag wire 阻力张线pitching movement 俯仰运动elevon 升降副翼all-wing aircraft 三角翼飞机fairing 整流罩，整流装置streamlined contour 流线型外形fireproof wall (fire-resistant wall) 防火墙gap 间隙，间隔，翼隔superposed airfoil 重叠机翼（双翼机获三翼机）stability 安定性，稳定性inspection door 检查口盖interplane strut 翼间支柱jury strut 辅助撑杆，副支柱，保险撑杆alighting gear 起落架，着陆装置propeller blade 螺旋桨桨叶lift wire (flying wire) 升力张线longeron 大梁（机身或短舱的）plating 重型金属蒙皮，表面镀层的金属板yawing movement 偏航运动pedal 脚蹬shock absorber 减震器，缓冲器slat 缝翼attack angle 攻角，冲角，迎角span 展长spanwise a. adj. 延机翼展向spar 机翼翼梁spinner 螺旋桨整流罩stagger 斜罩角compressor blade 压缩机叶片tandem-rotor helicopter 纵列式（双旋桨）直升机stagger wire 斜罩张线sweepback 后掠角antitorque rotor 尾桨，反扭矩尾桨tail skid 尾撬，尾部保护座tail wheel 尾轮chordwise adj. 弦向auxiliary fuel tank 副油箱，辅助油箱antenna 天线anti-collision light 防撞灯stair door 登机梯舱门engine nacelle 发动机短舱deicer boot 除冰带navigation light 航行灯construction 结构，构造longitudinal member 纵向构件bending stress 弯曲应力landing 着陆，接地，降落__cantilever wing 悬臂机翼，张臂机翼high-performance aircraft 高性能飞机external strut 外撑杆basic feature 基本特征beam 辆，横梁，柱monospar adj. 单梁，单梁的two-spar adj. 双梁，双梁的multispar 多梁，多梁的web （大梁）腹板，辅助梁，纵墙，肋板shear web 承减腹板spanwise member 翼展方向构件，展向构件high-wing monoplane 上单翼机tie rod 连干，系杆brace wire 张线drag load 阻力，阻力载荷built-up I beam 装配的I型梁，组合的I型梁extruded I beam 挤压成型的I型梁plain rib 普通肋，平面肋chordwise member 弦向构件compression rib 抗压翼肋，加强翼肋cap strip 翼肋缘条solid plywood web 整体的层板（胶合板）腹板cross bracing 交叉撑杆，横撑杆gusset vt. 角撑，角撑板，装角撑板于nail vt. 铁钉，钉住，用钉钉牢stamped rib 模锻翼肋truss-type cross section 桁架式横截面stiffener 加强杆，加强板，加强件fabric covering 布制蒙皮plywood covering 胶合板蒙皮，层板蒙皮tubular member 管型构件formed rib 维型翼肋integral fuel bay 整体油箱attachment fitting 安装街头，连接接头inspection 检查service vt. 服务，使用，维护，维修，检查，保养frontspar 前梁butt-rib 根部翼肋，平端头翼肋flange vt. 翼梁缘条，凸缘，突缘，（在----- 上）安装突缘end bow 机翼端部弯曲部分nose rib 前缘翼肋trailing edge strip 后缘条aileron control cable 副翼操纵钢索aileron control bell crank 副翼操纵双摇臂，副翼操纵双摇臂曲板tape v. 布带，带子，用带系扎FWD fuselage fitting 机身前接头washer 垫圈，垫片nut 螺帽retainer 护圈，卡圈，挡板，保持器dowel pin 定位销，和缝销钉，暗钉fuel vent line 燃油系统通气管路door 舱门，口盖，入口plate 板，盘，口盖tab 调整片，补偿片，操纵片，标签aileron tab 副翼调整片position light 航行灯landing and taxi light 着陆滑行灯fuel filler door 燃油注油口pitot tube 空速管，全静压管，全压管stall warning unit 失速警告装置RAM air inlet 冲压空气进口Federal Aviation Administration 联邦航空管理局Advisory Circular 咨询通告jet airliner 喷气式班机，喷气式航线客机jet engine 喷气发动机section 剖面，截面，型材，段，区域，部分assembly jig 装配架，型架inboard wing 内翼age hardening 时效硬化dimension 尺寸，大小bending load 弯曲载荷tensional load 扭转载荷stretch press 张拉成型机airfoil surface 翼型表面die vt. 冲切，用模（压）成型，模子，冲模，压模jaw 夹紧装置______________，钳口，夹爪airfoil contour 翼型外形formed 7075 sheet 成型的7075钣tab segment 弓形薄片接头forging adj. 锻造件splice vt. 拼接，绞结，拼接板，绞结处junction 接合，接合处，连接点wing tank 机翼油箱sealing compound 密封剂，密封腻子，封口胶center line 中心线，中线mating adj. 配合，连接，配合的，相连platform 平台hydraulic cylinder 液压做动筒synthetic rubber 合成橡胶center wing 中翼outboard wing 外翼swept-wing 后略翼nacelle 吊舱，发动机短舱production break 工艺分离面wide-bodied airliner 宽机体客机flight control surface 飞行操纵面pylon 吊架main frame 承力构架，主构架，承力隔框torque box 承扭盒段auxiliary structure 辅助结构permanent type fastener 永久式紧固件butt-spliced 平头对接，平头拼装flush fastener 埋头紧固件honeycomb panel 蜂窝板interference-fit 经配合，干涉配合close-tolerance fastener 高精度公差紧固件play 浮动，间隙，游隙tolerance 配合公差，容差，加工裕度flap vane 开缝襟翼导流片exterior plate doubler 外部双重加强板slat track 缝翼滑轨can 筒型壳，密封外壳，包套crew 空乘人员，机组，空勤组cargo 货物controls 操纵系统item 项目，零件，产品（均指已列入清单的项目）streamline form 流线型式accessory adj. 附属的，辅助的，附件，辅助设备，部件carburetor 汽化器，化油器，增碳器magneto 磁电机ignition lead 点火器导线strainer 过滤器fuel line 燃油管道turnover 回转，循环，翻倒，倒置emergency exit 紧急出口capacity 容量，容剂，能力classification 分类，类别，归类assemblage 装配，安装，总装配件bar 杆，棒，条lateral bracing 横向支撑tubular fuselage member 管状机身构件interval 间隔，间隙，距离bay 隔间，隔舱，段diagonal member 斜构件，对角构件percentage 百分比，百分数，比率ring 环，圈，环形隔框bulging 膨胀，凸出，褶皱皮buckling 皱损，皱褶，波纹glue v. 胶，粘结剂，胶合，粘结aircraft-quality plywood 航空质量级的层板reinforcement 加强，加固，加强件，加强部分spar varnish 清光漆waterproof protective material 防水保护材料deterioration 变质，恶化，损坏penetration 尽头，穿透moisture 湿气，潮气，水气protective coating 保护涂层hangar 机库，把-----放入机库中evidence 证据，迹象，形迹rot 腐烂，腐朽fungus 霉菌，真菌wood cell 木材组织，木材微孔cone 圆锥，锥体，锥状物conical shape 圆锥形状cylindrical shape 圆柱形dope 航空用漆，涂布油fiberglass 玻璃纤维stinger 尾不整流锥turbulence 紊流airflow 气流streamlined nose 流线型机头fail-safe feature 破损安全特性tail section 尾部，尾段，尾舱titanium 钛rip-stop doubler 止裂加强板beaded doubler 串珠加强板window belt 窗口地带panel 壁板，地板，板材，仪表板，操纵台，面板，翼段various stage 不同阶段semiautomatic riveting machine 半自动铆接机器shaved riveting 平面铆接dlampong aetion 夹紧力，夹紧作用pounds per square inch (psi) 磅平方英寸kilo-pascals (kpa) 千帕斯卡uniform fastening 均匀一致的连接，均匀一致的紧固件countersunk cavity 埋头窝sealing quality 密封性fatigue life 疲劳寿命longitudinal stiffener 纵向加强件flattened hat section 扁帽型截面stress level 应力水平gauge 规格，尺寸，测量器，量规，卡规，铆钉行距pressure-cabin section 压力舱部分upside-down position 倒置位置dolly 平台车，铆钉顶铁，抵座，圆形锻磨fixture 夹具，卡具，定位装置，安装用具，型架，紧固extruded z transverse frame 挤压成型Z型截面的横向构件mating jig 装配架，总装型架cockpit enclosure 驾驶舱盖subassembly 分装件，部件，局部装配件fuselage shell 机身外壳channel frame 槽型截面构件floor 地板，底面seat track 座椅滑轨carpet 毡层，地毯，铺设地毯expansion beam 伸缩梁flight compartment 机组舱，空勤组舱attachment 廉洁，固定，接头stud bolt 桩螺栓passenger compartment 客舱nut strip 螺帽导板splice plate 拼接板spacer 间隔片，隔离物，垫片，垫圈insulation 绝缘，隔离__aisle panel 通道板freight v. 货物，货运，装货facilities v. 设备，装置，工厂，实验室fabrication 制造，装配，生产individual panel section 单独的壁板区段railroad car 有轨电车handing 处理，加工，操纵，管理，装卸，搬运，吊运handle v. 收兵，把手，处理suction-cup principle 空吸杯装置overhead monorail system 高架单轨吊车系统manufacturing cycle 生产周期sheet-metal holder 钣金夹持器arrangement 排列，布置，安装，构造，布局station number 站位编号distance 距离zero reference point 零参考点floor beam 地板梁keel beam 龙骨梁，底部大梁stretch-formed skin panel 拉伸成型蒙皮板stressed skin 承力蒙皮multiple-element contracture 多元件构造torsional unit 整体部件，组合件advancement 进步，前进，改进state-of-the-art 技术发展水平，目前工艺水平，工艺状态cutaway drawing 剖视图intercostal 加强肋，肋间的material 材料process 过程，流程，工序，步骤，工艺规程，工艺技术，制作方法conclusion 结论fatigue crack 疲劳裂纹corrosion 腐蚀cause 原因，理由，起因stress concentration 应力集中surface corrosion 表面腐蚀galvanic corrosion 电化腐蚀pitting corrosion 点状腐蚀，坑蚀intergranular corrosion 晶界腐蚀exfoliation 剥离，剥落stress corrosion 应力腐蚀fretting corrosion 磨损腐蚀，擦伤腐蚀dissimilar metal 不同金属metal bonding 金属粘结seam 接缝，接口，接合面damage 损伤，破坏，故障，事故roller 磙子，滚桶，碾压机chemical cleaning 化学清洁etching process 浸蚀加工，酸洗处理corrosion-inhibiting epoxy-type primer 防腐蚀环氧树脂底层涂料curing 处置，处理，固化处理epoxy adhesive 环氧树脂粘结剂Teflon fluorocarbon resin release cloth 特氟隆碳氟化合物树脂防粘布bleed cloth 透气布vacuum bag 真空袋autoclave 蒸压器adhesive 粘性的，粘合剂thermosetting epoxy resin 热固型环氧树脂ultrasonic inspection equipment 超声波探伤设备void 空学，空洞porosity 集气孔，沙眼，松孔cabin altitude 座舱高度pressure differential 压力差flight station 乘员舱，（机组人员）飞行工作位置cabin pressurization load 座舱增压载荷titanium fail-safe strap 钛金属破损安全带clad alloy 包覆金属entrapment 夹带，截留formation 形成，组成，构成lighter-gauge skin 较薄的机身蒙皮heavy-gauge skin 大规格蒙皮，厚蒙皮shot penning 喷丸强化，喷丸处理main frame 主隔框，承力隔框，中部最大隔框，主机架stopper 止动器，限制器channel 槽型型材，沟槽，______________管道，通道cut out 切口，开口attaching-clip angle 固定卡箍的角材overlapping 重迭，搭接overlapping stringer 搭接桁条center line 中心线transverse beam 横梁wing box 机翼翼盒wheel well 机轮舱，轮舱deck 地板，层舱sulfuric acid anodizing 硫酸阳极化处理organic-coated steel fastener 有机物涂层的钢紧固件polyurethane painting 聚氨酯涂料corrosion-prone area 易于腐蚀的部位filled-sealed adhesive 嵌缝密封粘合剂passenger door 客舱门center elevating coat room 中央升运保护涂层位置galley service center (机上) 厨房服务中心radome compartment 雷达无线整流罩舱avionics compartment 电子设备舱cargo compartment 货舱center wing 中央翼，中翼cargo door 货舱舱门accessory compartment 附件舱waste tank compartment 废液容器舱fuel vent collection box 燃油通气集油盒（进入同期管道的油在此集中再抽回油箱）rueling interconnect line 加油互连通管道fuel tank 燃油油箱escape chute 应急离机口，应急离机滑梯，应急脱离滑道pressure fueling/defueling couplings 压力加油/放油接头hydraulic service center 液压服务中心galley lift （机上）厨房升降梯air conditioning duct 空气调节系统管道，空调管first class seating 头等舱座椅lavatory 卫生间，盥洗室weather radar 气候雷达curved windowshield panel 弯曲成型的挡风玻璃Rolls Royce RB211 turbofan 罗—罗，RB211涡轮风扇geared elevator 随动升降舵（可操纵水平安定面的）flying stabilizer 可操纵安定面auxiliary power unit (APU) 辅助动力装置pressure dome 球形气密隔框electronic service center 电子设备服务中心after hold (bulk cargo) 后货舱（散装货物，笨重货物）coach class seating 二等舱座位conteinerised cargo 集装箱货物double slotted flap 双开缝襟翼inner aileron 内副翼outer aileron 外副翼full span slat 全展长缝翼inward retraction main wheel 向内收起的主机轮forward retraction nose wheel 向前收起的前机轮air conditioning bay 空调设备舱scale 规模，比例，标尺fin 鳍，垂直安定面，垂直尾翼，立尾elevator 升降舵empennage 尾翼appearance 外形，外貌，外表，外观，出现，出版，发表span 翼展，跨距，间距auxiliary spar 辅助梁hinge v. 铰链，合页，铰接接头installation 装置，设备，安装，装配dorsal fin 背鳍streamlined fairing 流线型整流罩swept-back vertical stabilizer 后掠式垂直安定面stabilator 全动式水平尾翼primary controls 主操纵系统secondary controls 辅助操纵系统aileron assembly 副翼装配件repair 修理maintenance 维护，维修technician 技术人员，技师，专门人员proof of strength 强度验证，强度试验limit load test 最大使用载荷试验，限制载荷试验horn 角状物，操纵摇臂rigging load 校装载荷，水平调整载荷，装配载荷rational manner 合理的方式conservation manner 保守的方式movable tail surface 可动的尾部翼面adjustable stabilizer 可调节的安定面（安定面的安装角，可以改变）ultimate bearing strength 极限挤压强度mass balance 质量平衡concentrated mass balance weight 集中的质量平衡重量control system operation 操纵系统的工作function 功能，职能，作用confusion 混淆，干扰，混乱primary flight controls 飞行主操纵系统pitch 抚养，绕横轴的运动，桨叶角，桨距，紧固件的间距yaw v. 偏航运动，偏航two-control airplane 双操纵面飞机lateral control 横侧操纵directional control 方向操纵stop v. 停止，制动，止动器，止动块，止动装置wear v. 磨损slackness 松弛度take-up adjustment 拉紧调整trim system 配平系统precaution vt. 预防措施，小心，注意，警惕pilot 驾驶员trim device 配平装置irreversible tab 不可逆调整片reliability 可靠性unmistakable warning 清除无误的警告，明显的警告control system lock 操纵系统锁light twin airplane 轻型双发动机飞机jackscrew attachment point 螺旋千斤顶安装点hinge point 铰接点elevator balance panel bay 升降舵平衡翼板隔间flash beacon 闪光灯标attach bracket 固定支架primary flight control surface 飞行主操纵面cruising operation 巡航操作fabric 织物，织品，布，纤维织品water-proof 放水，不漏水，不透水coating 涂层drain hole 放油孔，排水孔，泄漏孔hinge line 铰链轴线auxiliary control surface 辅助操纵面doubler 加强板balance weight 平衡重量access door 检查口盖，工作窗，舱门access panel 口盖，舱盖honeycomb 蜂窝结构vertical axis 立轴flutter 颤振aerodynamic surface 气动力面bracket 支架，托架hinge bracket 铰链支架，铰链架displacement 位移，偏转，偏度aerodynamic efficiency 空气动力效率，气动效率，升阻比control tab 操纵屏，随动补偿片static balance 静态平衡aerodynamic balance 气动平衡，气动补偿dynamic balance 动平衡，飞行中立或力矩的平衡ruddervator V型尾翼，方向升降舵secondary flight control surface 飞行辅助操纵面straight and level flight 直线水平飞行servo tab 伺服片，随动补偿片，操纵片control wheel 驾驶盘，操纵轮crank 祛病，手柄，摇臂cable system 钢索系统actuating device 致动装置screwjack 螺旋千斤顶，螺旋致动器logical manner 合理的方式top rim 顶部轮缘，顶部轮圈position indicator 位置指示器push-pull rod 推拉杆，传动杆set-back hinge line 后置铰链轴线track fitting 滑轨接头leading edge slat 前缘缝翼scalloped doubler 扇形式样加强板fiberglass trailing edge 玻璃纤维后缘beaded-doubler inner skin 串珠状加强板内蒙皮feedback fitting 反馈接合actuation 致动器damper 阻尼器，缓冲器，减震器hinge pin 铰链销cotter pin 开口销，开尾销bearing 轴承control arm 操纵臂，操纵杆balance-weight arm 平衡重量支撑臂detachable elevator 可拆卸的升降舵，可分开的升降舵copilot 副驾驶员headroom 净空（高度），头上空间visibility 能见度，视野clearance 间隙，间距，惊恐，余地，清理，排除parachute 降落伞provision 准备，预备，设备，装置aerobatics 特技飞行，航空表演demonstration 论证，说明，显示，示范flight test 飞行试验flying ability 飞行技能，飞行员驾驶技术egress 出口，出路，外溢personnel 全体人员，全体职员navigator 导航设备，导航仪，领航员flight engineer 随机工程师，空勤机械师appurtenance (常用复数) 附属设备，附件，配件，辅助工具safety vt. 安全性，安全措施，安全，保险assurance 确信，把握，信心，保证concentration 集中，浓缩，聚集propeller-driven airplane 螺旋桨飞机blade 叶片，桨叶air-transportation service 空运服务seal 蜜蜂，封严，密封装置，密封垫，密封胶windshield 风挡，风挡玻璃single-place airplane 单座飞机accommodation 调节机能，适应____________(w，供应，膳宿供应，座位，铺位agriculture aircraft 农业用机instrument 仪表，仪器furnishing 装备，装置，设备，供给dual controls 双重操纵机构first pilot 正驾驶，机长second pilot 副驾驶statement 叙述，陈述，论点up-to-date information 最新的资料ventilation 通风，排起，换气vision 观测，目击，观测，视线，视力windshield wiper 雨刷，风挡刷storm window 风雨窗，双层窗airstream 气流glare v. 闪光，强烈刺目的光reflection 反射，折射，偏射windshield panel 风挡窗格玻璃，窗格玻璃impact 碰撞，冲击，撞击flight path 飞行轨迹，航迹velocity 速度transparent plastic sheet 透明塑料板flanged doubler 弯边的加强板，带凸缘的加强板retaining strip 固定带waterproof adhesive tape 防水胶布带vinyl channel 乙烯塑料槽型件thickness 厚度stiffness 刚度，刚性，安定性，稳定性contour 轮廓线，外形cowl deck 整流罩平台felt seal 毛毡密封indentation 压痕，凹槽manufacturer 制造厂，生产厂家maintenance manual 维修手册laminated panel 层板forged frame 锻制框架，锻造框架hnoist provision 起重设备gasket seal 垫片密封，填料密封removal 拆卸vinyl interlayer 乙烯塑料中间层phenolic spacer 酚醛垫片，酚醛间隔物phenolic block 酚醛块gasket silicone seal 硅铜填料密封剂semi-tempered glass 半强化玻璃terminal 终端，终止，接线柱，引线接头autopilot engage 自动驾驶仪接通navigation marker light 航行标示灯，导航信标接收机信号灯airspeed indicator 空速指示器，空速表pilot directional indicator 自动驾驶仪航向指示器gyro horizon 陀螺地平议，航空地平议compass card 罗盘刻度盘altimeter 高度表，高度计rate of climb 爬升率emergency pneumatic brake 应急气动刹车，应急冷气刹车autopilot axis indicator 自动驾驶仪接通指示器ice-detector light 积冰探测灯engine pressure ratio 发动机压力比，发动机增压比engine r.p.m 发动机每分钟转速thrust-reverser operating light 反推力工作指示灯tailpipe temperature 排气温度管，涡轮后温度master warning 主警告gear down, lock light 起落架放下，锁定信号灯fuel flow 燃油流量tachometer 马赫数表，M数表navigation radio selection 导航无线电选择仪glide slope light 下坡滑度指示灯autopilot disengage 自动驾驶仪切断radio and radar control 无线电和雷达控制air-brake handle 气动刹车减速手柄，减速扳手柄weather radar scope 气象雷达显示器thrust lever 推力杆，油门杆parking-brake letch 停机刹车锁engine start lever 发动机启动手柄turn and bank indicator 转弯侧滑仪hydraulic system pressure 液压系统压力stabilizer trim wheel 安定面配平手轮rudder trim 方向舵配平door post 门框aluminum extrusion 铝挤压件outer retainer 外部固定件，外部保持件temperature sensing element 热敏元件five-ply laminated panel 五层层压窗格玻璃insert 垫圈，插入物defog bus bar 清除混蚀汇流条，扫雾汇流条conductive coating 导电敷层chip retarder 碎裂阻聚剂anti-ice bus bar 防冰汇流条air carrier 航空运输公司，空运工具，运输机presence 存在fuel fume 燃油蒸汽，燃油雾气carbon mobixide 一氧化碳dangerous trace 危险的痕迹ventilation system 通风系统heating system 加温系统pressurization system 增压系统first-class section 一等客舱段trijetliner 三发喷气式航线客机airline 航线，航空公司coach section 二等舱客段broad lofty ceiling 宽阔高耸的舱顶spaciousness 宽敞，宽敞度aisle 通道，走廊divider 分配器，分隔器personal effects 个人财物carry-on luggage 随身的行李safety-belt 安全带，保险带cycle pressurization loading 循环增压载荷pressurized airliner 座舱增压式航线客机cabin sidewall lining 座舱侧壁材料fail-safe structure 破损安全结构acrylic plastic 聚丙烯塑料peripheral seal 周边密封，周缘密封sponge rubber 泡沫橡胶，多孔橡胶spring retainer 弹簧座圈shouldered screw 带托肩的螺钉window-frame forging 窗框锻件reveal 窗框半槽边，窗侧retaining bracket 固定架window ring pan 环形窗框clip 夹子，卡箍slit 长缝，裂缝conditioned air 以调节空气condensation 凝聚，凝结acoustical seal 吸音密封window shade 窗户遮光罩，窗帘acoustical pane 吸音窗玻璃side wall panel 侧壁板formed sheet-metal structure 预成型钣金结构hydro press 水压机stamp press 冲压机，模锻压力机drop hammer 落锤entrance 进口upholstered cabin 装饰过的座舱matching upholstered panel 匹装备饰板door latching 门扣locking mechanism 锁机构forward entry door 前登机门hinge gate 铰接活门door opening 舱门口hinging mechanism 铰接机构，门枢机构controlling mechanism 操纵机构，控制机构plug 塞子，孔塞，堵塞物securing mechanism 关紧机构inside handle 内部手柄cam plate 凸轮盘，凸轮板latching-crank assembly 柄锁装配件angular movement 角运动latch rod 锁杆latch roller 锁滚柱cock-crank assembly 竖起的曲柄装配件torque-tube crank 扭转曲柄hinge arm 铰接臂guide arm 导向支臂snubber 缓冲器，消音器assist handle 辅助手柄radius link 摇柄pivot axis 止动销stop pin 止动板latch pin 锁销door-open stowing latch lever 舱门打开收锁杆remainder 剩余部分recessed handle 隐藏式手柄，隐藏在凹坑处的手柄complexity 错综复杂，复杂的事物bogy 小车，转向架normal mode 普通型emergency mode 应急型auxiliary mode 辅助型emergency evacuation slide 应急排空滑块deployment 部署，展开，散开，开伞reveal seal 窗侧密封outer pane spring assembly 外部窗格玻璃弹簧装配件permanently mounted screw 永久性固定螺钉nutplate 托板螺帽ventilation hole 通气孔ventilation slot 通气缝window trim 窗狂细木工件，窗框装饰trim pad 细木窗框衬垫escutcheon plate 锁眼盖，孔罩板handle mechanism housing 手柄机构外壳avionics compartment lower door 电子设备下舱门avionics compartment aft door 电子设备后舱门air conditioning compartment door 空调舱门forward passenger door 前客舱门center accessory compartment door 中央辅助设备舱门overawing passenger door 机翼上方客舱门center cargo door 中央货舱门APU compartment door 辅助电源设备舱舱门tail cone lower door 尾锥下舱门overstress 过大应力，过载，超载overstressing 过应力，超限应力landing load 地面载荷（指起飞，着陆或在地面滑行时，飞机结构承受的载荷）fixed landing gear 固定式起落架retractable landing gear 收放式起落架conventional arrangement 常规配置，正常配置tricycle arrangement 前三点布局，前三点配置tricycle landing gear arrangement 前三点式起落架布局nose wheel 前轮old conventional gear 旧式常规起落架tail-wheel type 尾轮式main gear 主起落架strut 支柱，撑杆，吊架body-gear strut 机身起落架支柱wing-gear strut 机翼起落架支柱nose-gear wheel 前起落架机轮main wheel 主轮axis 轮轴，车轮main beam 主梁caster 脚轮，转向轮swivel 旋转接头，旋转节，旋转shock-absorbing method 减震方法rubber shock cord 橡皮减震绳，缓冲绳rubber disk 橡皮盘coil spring 螺旋弹簧，盘簧hydraulic piston 液压活塞flexible spring steel 柔性弹簧钢oleo 油液减震器，油液减震支柱air-oleo 空气—油液减震器spring-oleo 弹簧—油液减震器flexibility 柔性，韧性，挠性elasticity 弹性alloy steel 合金钢brake 刹车air-oleo strut 油气式减震支柱cylinder 气缸，做动筒，圆筒metering piston 分油活塞，分油柱塞orifice 小孔metering pin 调节油针taxi 滑行cross-sectional drawing 剖视图retracting system 收起系统trunnion 轴颈，枢轴，耳轴retracting mechanism 收起机构electric operated screw 电操纵螺杆hydraulic actuating cylinder 液压致动作动筒civil airplane 民用飞机，民航飞机linking device 连接机构drop-test 着陆重量（起落架）落震试验，冲击试验wheel well door 起落架舱门，轮舱盖supporting structure 支撑结构friction 摩擦力inertia 惯性brake torque 刹车扭矩air load 气动载荷retraction 收回extension 伸出，延伸stalling speed 失速速度approach position 进场着陆位置cruising speed 巡航速度load factor 载荷因数，过载，装载系数（有效载荷与飞机起飞重量比）yawing maneuver 偏航运动，方向动机positive means 可靠的方法safety switch 安全电门，保险开关emergency system 应急系统emergency means 应急方法operational test 使用实验，工作实验retracted position 收上位extended position 放下位landplane 陆上飞机aural warning device 声响报警装置，声响报警器throttle 节流阀，节流油门，节气门manual shutoff 手动关断landing-gear control knob 起落架控制按钮transport-airplane 运输机tire 轮胎，轮箍multiple landing gear 多轮起落架compressed air chamber 压缩空气室piston tube 活塞管inner cylinder 内筒outer cylinder 外筒oil chamber 油室power plant 动力装置，发动机mount 支架座，安装，固定，装配enclosed shelter 封闭的掩蔽所multiengine airplane 多引擎飞机National Aeronautics and Space Administration (NSAS) 国家航空和宇航局stream-lined structure 流线型结构pod 吊舱，短舱，分离舱，可拆卸的货舱pylon 外挂梁，吊架，挂架，支架engine mount 发动机架formed sheet metal 冷弯钣金件welded steel tube 焊接钢管forged steel 锻制钢reciprocating (position) engine 活塞式发动机overhaul 大修engine change 发动机更换liquid line 液体管路electric cable 电缆control linkage 操纵线系quick-disconnect joint 快速拆卸接头quick engine change (QEC) 快速更换发动机package 组件，部件，成套设备radial engine 星型发动机opposed engine 对置式发动机bushing 衬套，衬筒vibration absorption 震动吸收pad 沉淀，填料，垫片，底座台cushion 垫子，软点，减震垫restraining action 约束作用manufa cturer’s handbook 制造厂手册mount bracket 固定托架，安装托架dynamic suspension 非刚性支撑法，减______________震悬。
航空维修相关中英文对照
业务范畴缩写全称中文简述工程文件AC Advisory Circular 咨询通告是各职能部门下发的对民用航空规章条文所作的具体阐述AD Airworthness Directive 适航指令试航当局颁发的为保证飞行器适航的通知，强制执行SB Service Bulletin 服务通告制造厂商发布的关于飞行器或附件的修理通告，有非强制执行的，也有强制执行的SL Service Letter 服务信函制造厂商发出，通常是信息类的，级别低于SBSIL "Service Information Letter" 服务信函同SLEB Engineering Bulletin 工程通告工程部门颁发的附件改装通告EO Engineering Order 工程指令工程部门颁布的改装通告拆发指令工程部门颁发的发动机拆换指令TO Technical Order 技术通告用于解释EO的工程文件MT Maintenance Tip 维修提示CMR C ertification Maintenance Requirement 审定维修要求通常与ALI一起作为MRBR的附件，是航空公司制定维修计划的基础之一。
MPD M aintenance Planning Data 维修计划大纲、维修计划文件制造商按机型发布的维修方案，是航空公司指定维修方案的重要依据依据之一。
MRBR Maintenance Review Board Report 维修审查委员会报告维修审查委员会报告是针对新型和衍生型航空器由航空器制造人制定并由民航总局批准的初始最低计划维修和检查要求，包括维修任务和维修间隔。
它是航空运营人针对该机型制定初始维修方案的基础。
CAMP Continuous Airworthiness Maintenance Program 持续适航维修方案航空公司制定的维修方案，包括维修项目以及维修间隔MTOP Maintenance Task Operation Plan 维修实施计划航空公司制定的维修方案实施计划，与CAMP的区别是MTOP的条目按照CAMP规定的间隔进行了打包。
机械维修电器等专用工具术语汉英对照(民航类)
toolbox 工具箱bench 工作台vice, clamp 虎钳（美作：vise）saw 锯bow saw 弓锯circular saw 圆锯（美作：buzzsaw）compass saw, scroll saw 钢丝锯fretsaw 细锯handsaw 手锯chisel 口凿cold chisel, burin 冰凿gouge, firmer gouge 半圆凿plane 刨子moulding plane 型刨jack plane 粗刨rabbet plane 槽刨drawknife 刮刀scraper 三角刮刀rasp 粗锉file 锉square 尺miter 斜槽规scriber 近线尺set square, triangle 三角板brace 手拉曲柄锉hand drill 手钻drill, bit 钻，有柄钻gimlet, auger 钻，无柄钻countersink 锥口钻gauge, marking gauge 量规hammer 锤mallet 木槌nail 钉brad 平头钉tack, stud 圆头钉screw 螺丝钉screwdriver 螺丝刀，改锥screw tap 螺丝攻nail puller 拔钉器ruler 尺tape measure 卷尺folding ruler 折尺sandpaper, emery paper 砂纸toolbox 工具箱bench 工作台vice, clamp 虎钳（美作：vise）saw 锯bow saw 弓锯circular saw 圆锯（美作：buzzsaw）compass saw, scroll saw 钢丝锯fretsaw 细锯handsaw 手锯chisel 口凿cold chisel, burin 冰凿gouge, firmer gouge 半圆凿plane 刨子moulding plane 型刨jack plane 粗刨rabbet plane 槽刨drawknife 刮刀scraper 三角刮刀rasp 粗锉file 锉square 尺miter 斜槽规scriber 近线尺set square, triangle 三角板brace 手拉曲柄锉hand drill 手钻drill, bit 钻,有柄钻gimlet, auger 钻，无柄钻countersink 锥口钻gauge, marking gauge 量规hammer 锤mallet 木槌nail 钉brad 平头钉tack, stud 圆头钉screw 螺丝钉screwdriver 螺丝刀，改锥screw tap 螺丝攻nail puller 拔钉器ruler 尺tape measure 卷尺folding ruler 折尺sandpaper, emery paper 砂纸stepladder 高凳，折梯trestle 支架trowel 灰泥镘子float 抹子spatula 抹刀，刮铲brush 刷子paintbrush, brush 画刷roller 滚子scissors 剪子spade 锄fork 叉子shovel 铁锹，铲rake 耙roller 滚压器，碌碡dibble 掘穴机wheelbarrow 小车，独轮车watering can 喷壶garden hose, hosepipe 橡胶软管lawnmower 剪草机shears, garden shears 园艺剪刀pruning shears 修枝剪pruning knife 修枝刀sickle 镰刀scythe 钐刀，钐镰trowel 镘weeding hoe 除草耙seed drill 条播机penknife 铅笔刀glass cutter 玻璃刀plumb line 铅垂线spirit level 水平仪pickaxe 鹤嘴锄（美作：pickax）the axe 斧子（美作：the ax）sledgehammer 长柄大锤bushhammer 石工锤rammer 撞针anvil, beakiron, bickiron, two-beaked anvil 砧，砧子bellows 弹簧awl 锤子beam compass, trammel 长圆规lever 杠杆tyre lever 轮胎撬杠crank 柄soldering iron 焊铁，烙铁blowlamp 吹嘴，吹炬（美作：blowtorch）die 冲模diestock 螺丝攻machine tools 工作母机lathe 车床turret lathe 六角车床milling cutter 铣刀milling machine 铣床electric drill, power drill 电钻grinder, crusher 粉碎机riveter 打铆机rolling mill 轧板机press 压床，冲床drop hammer pile hammer, drop hammer 蒸汽汽锤air hammer, pneumatic hammer 气锤pile hammer 打桩机机械维修电器等专用工具术语汉英对照一画一字螺丝批slot type screwdriver一点透视one-point perspective二画二合一黏合剂epoxy resin adhesive二合胶；混合胶epoxy glue二维的；平面的two-dimensional二进制binary二极管；整流子diode二号螺丝攻second tap二路开关two-way switch十进制的；公制的metric人工制品artefact人造板man-made board人体工程学ergonomics; human engineering 人体尺寸human dimension人体测量学anthropometry; anthropometrics 刀片blade刀身blade刀具tool刀具溜座carriage刀柱tool post刀架tool rest刀架底座tool rest bracket刀座帷；床鞍apron刀座鞍；溜板座saddle力force力三角形triangle of force力平行四边形parallelogram of force力多边形；多边形力学polygon of force力的分解force resolution力架；亮漆lacquer力矩moment力偶couple力矩定律law of moment力-距离图表force-distance graph力图force diagram力线line of force力点effort十字榫cross halving joint十字螺丝Philip's head screw十字螺丝批Philip's type screwdriver丁字尺；T 尺tee square三画三爪夹头three-jaw chuck三角尺set square三角形结构系杆triangulation tie三角锉triangular file三维的；立体的three-dimensional三氯甲烷；哥罗芳chloroform三聚氰?胺；蜜胺melamine三点透视three-point perspective上油漆painting上釉enamelling凡立水varnish叉形顶尖fork centre口罩mask士力；虫漆shellac士巴拿；扳手spanner大芯夹板；宽条芯夹板blockboard; solidcorestock-laminated board大量制造mass production 子口刨；槽口刨；边刨rebate plane小型平槽刨miniature router plane小型线料弯曲器small wire bender小型弯折机mini bender小型电路断路器；跳菲miniature circuit breaker (MCB)小齿轮pinion山樟San Cheong工件workpiece工字梁I beam工作面working surface工作图；制作图working drawing工作台bench; working table工具tool工具贮存室tool storage工具槽well工具钢tool steel工场workshop工场安全workshop safety工程字书写技巧lettering工程系统engineering system工程绘图engineering drawing工业酒精；火酒methylated spirit弓形手钻；手摇曲柄钻brace弓形手钻嘴brace bit弓锯bow saw; hacksaw弓锯片hacksaw blade弓锯床hacksawing machine四画不平衡imbalance不含铁金属；非铁金属non-ferrous metal不贯穿孔；闭孔；盲孔blind hole不贯穿鸠尾榫lapped dovetail joint不对称asymmetry不锈钢stainless steel不稳定平衡unstable equilibrium中心centre中心线centre line中心冲centre punch中心钻centre drill中心钻嘴centre bit中央处理器central processing unit (CPU)中性neutral中性平衡；随遇平衡neutral equilibrium中性轴neutral axis中密度纤维板medium density fibre board (MDF)中粗锉纹second cut中碳钢medium carbon steel中线neutral wire互补金属氧化物半导体complementary metal oxide semiconductors (CMOS)介子；垫片washer介指铁ring mandrel介电常数；电容率permittivity介稳态的；亚稳态的metastable内力internal force内卡尺inside calipers内能internal energy内涵性质intensive properties内圆弯凿scribing gouge内锁式配件interlocking fitting内燃机internal combustion engine内螺纹制造法tapping内螺丝internal thread内弯边concave edge六角金属枝hexagonal bar六角匙Allen key六角头螺丝hexagonal head screw公制的；十进制的metric公差tolerance冗余构件redundant member分力component force分子molecule分子力molecular force分切；分割；切断parting off分贝decibel分析analysis分析及批判学analytical and critical studies 分析器analyzer分流器shunt分界面；界面；接口interface分厘卡micrometer分规divider分割车刀架parting tool holder分解decomposition 分压器potential divider; voltage divider 隔离开关isolating switch切削工具cutting tool切削液cutting fluid切削深度depth of cut切屑；碎屑chip切线锯法tangential sawing切辊纹；滚纹knurling切断；分切；分割parting off切断工具parting tool勾；勾脚hook勾刀；胶片?刀plastic cutter化胶水tensol反向偏压reverse biased反相放大器inverting amplifier反相器inverter反射reflection反电动势back e.m.f.反馈；回输feedback天拿水；稀释剂thinner天梯牙；齿条gear rack天然木材natural timber天然干燥法air seasoning孔隙率porosity尺寸dimension尺寸线dimension line尺身blade引力；重力gravitational force心形凸轮heart-shaped cam心材heartwood心轴mandrel心销core pin手工具hand tool手工锯junior hacksaw手削法paring手持虎钳hand vice手柄handle手套gloves手扫漆brushing lacquer手推车barrow手提式竖线锯portable jigsaw手提电动工具portable power tool手提电钻electric hand drill手进给hand feed手摇曲柄钻；弓形手钻brace手摇钻hand drill手锉hand file手锯；板锯handsaw手锥bradawl手辘轧机hand rolling machine支柱；支撑物strut支架；支座support支点fulcrum; pivot文字text方向direction方向针pointing needle方枝square bar方波形square waveform方波产生器squarer方型牙板rectangular die方格纸；网格纸grid paper方通square tube方块图block diagram方锉square file方头钻嘴square shank bit方螺帽square nut方边凿；直边凿firmer chisel木wood木工woodwork木工工作间woodwork area木工工作台woodworker's bench木工车床wood turning lathe; woodworking lathe木工铅笔carpenter's pencil木工刨床thicknessing and planning machine 木牙螺丝；木螺钉wood screw木材timber木材车削wood turning木材车削工具wood turning tools木屑压合板；万花板chipboard木条接榫corner strip joint木圆头槌doming mallet木模；模型patterns木线wood strip木胶粉ureaformal dehyde resin glue木锉rasp木螺钉；木牙螺丝wood screw木槌mallet 止推轴承thrust bearing止推垫圈thrust washer比例proportion比例尺scale比例常数proportionality constant比例极限proportional limit比较器comparator比热容量specific heat capacity水平投影面horizontal plane水平仪；平水尺spirit level水气掣；漏电断路掣earth leakage circuitbreaker (ELCB)水晶胶；聚酯树脂polyester resin水晶胶的铸造成形resin casting水磨砂纸silicon carbide paper火叉firing fork火水；煤油kerosene火牛；变压器transformer火石轮grinder火花电蚀法；放电极加工electrical discharge machining火酒；工业酒精methylated spirit火钳tongs火线；活线live wire火砖fire brick爪扣；爪形离合器；犬齿式离合器dog clutch 牙板；丝模die牙板扳手；丝模扳手die holder (stock)牙板螺帽die nuts牛皮胶；动物胶animal glue牛油纸tracing paper牛顿运动定律Newton's laws of motion犬齿式离合器；爪扣；爪形离合器dog clutch 五画丙烯;丁二烯苯乙烯acrylonitrile-butadiene-stryrene (ABS)主轴；心轴spindle主题motif令(纸张的计数单位) ream凹座recess凹模hollowing block凸缘flange凸缘联轴节flange coupling凸轮cam凸轮式配件cam-action fitting凸轮传动cam drive凸头螺丝raised head screw加成作业；添加法addition process加油oiling加速器accelerator功能；用途function功率因子power factor功率放大器power amplifier功率板power amplifier board功率晶体管power transistor包氏记号法Bow's notation「包浩思」；「包豪斯」〈设计风格) Bauhaus 半永固法；半永久接合semi-permanent joining半接榫halving joint半闭式槽榫stopped housing joint半圆(木)锉half-round rasp半圆车刀turning gouge半圆锉half-round file半圆头铆钉snap rivet半导体semiconductor卡路里；卡(热量单位) calorie卡纸card paper卡尺；测径器calipers去角；倒角chamfer可切削性machinability可行性feasibility可逆过程reversible process可压缩性compressibility可变电阻variable resistor四分仪quadrant四爪夹头four-jaw independent chuck四圆心法(绘图) four-centre method外卡尺outside calipers外形塑造shaping外形线；轮廓线outline外推法extrapolation外圆弯凿firmer gouge外螺纹external thread外螺纹制造法threading外弯边convex edge 外观appearance失真distortion尼龙；聚醯胺nylon; polyamide (PA)尼龙墨水针笔technical felt-tip pen左右调校杆lateral adjusting level市售尺寸；标准尺寸stock size市电频率；电源频率mains frequency平(木)锉flat rasp平水尺；水平仪spirit level平行投影parallel projection平行车削parallel turning平行虎钳parallel vice平行钉法parallel nailing平底弯刨flat faced spokeshave平底钻嘴forstner bit平板结构slab construction平流扼流圈；滤波扼流器smoothing choke 平流电容器；滤波电容器smoothing capacitor平流电路；滤汳电路smoothing circuit平面板；正台surface plate平面图；俯视图plan平面锤flatter平移translation平搭榫corner halving joint平嘴钳flat nose pliers平槽刨router plane平衡balance; equilibrium平衡力equilibrant平衡条件equilibrium condition平衡电桥balanced bridge平头弧刀square nose gouge幼纹smooth cut打凹成形hollowing打凸成形raising打槽机routing machine打线；打槽routing打磨fitting; polishing打磨机polisher本生灯Bunsen burner本征半导体intrinsic semiconductor正反器；触发器；复振器flip-flop正反馈；正回输positive feedback正火normalizing正向偏置forward bias正投影orthographic projection正投影图orthographic drawing正弦波形sinusoidal waveform正面投影front projection正视图elevation; front elevation正极；阳极anode正齿轮spur gear正台；平面板surface plate永久性接合permanent joining瓦通纸；瓦楞纸板corrugated board生长层cambium layer生产图production drawing生胶浆rubber cement生钢；铸钢cast steel生铁；铸铁cast iron用途；功能function白杨木poplar白胶浆PV A glue; white glue皮沙垫leather sandbag皮革leather皮革黏合剂leather glue皮鞋leather shoes目录contents矢量；向量vector石灰岩limestone石英晶体振荡器quartz crystal oscillator石棉asbestos; asbestus石膏Plaster of Paris示波器oscilloscope立体图pictorial drawing六画交流电流alternating current (a.c.)交流电压 a.c. voltage交联结构cross-linked structure仿饰金gilding metal伏特volt光力架clear lacquer光拉软钢bright drawn mild steel (B.D.M.S.) 光敏电阻light dependent resistor (LDR)光测弹性学photoelasticity光刨；滑刨smoothing plane 光电效应photoelectric effect光泽lustre全闭式槽榫closed housing joint共面力coplanar force共聚合作用co-polymerization共聚物copolymer共价键covalent bond共振；共鸣；谐振resonance印刷电路板printed circuit board (PCB)同素异形allotropy同轴电缆coaxial cable同温equality of temperature向量；矢量vector向量和vector sum合力resultant force合口扁钳close mouth tongs合成色；等和色secondary colour合成品composite合成粅料composite material合金alloy合金工具钢alloy tool steel合钉；定位销dowel回火tempering回复力restoring force回复力偶restoring couple回弹resilience回输；反馈feedback地线earth wire多刃切削刀具multi-point cutter多孔塑料；泡沫塑料；海绵状塑料foam plastics多方榫接合pinned joint多媒体multi-media多晶性polycrystallinity多谐振动器；多谐振荡器multivibrator多边形力学；力多边形polygon of force字母冲letter punch字板letter stencil安全safety安全守则safety rule安全系数safety factor安全措施safety precaution安全眼罩safety goggle安全设备safety equipment安全药箱safety box安培ampere安培计；电流表ammeter尖脚spur年轮annual ring成本cost成形forming扣件；击固件fastener扣钉clout nail; cramp托架bracket收缩shrinkage曲柄crank曲柄轴crank shaft曲线规；云板；云尺French curve有效的efficient有效电流effective current灰；灰末ash百折胶；百折胶；聚丙烯polypropylene (PP) 竹bamboo羊角锤claw hammer老化ageing肋条rib肌理；质感；质地texture自由度degree of freedom自动控制automatic control自动进给auto-feed自然干燥法natural seasoning自感量self-inductance自感应self-induction色彩；颜色colour色调tone色环colour wheel行星齿轮；周转齿轮epicyclic gear七画肘节开关toggle-switch串激电动机；串绕电动机series-wound motor位能；势能potential energy位梯度；势梯度potential gradient位移displacement位错dislocation伸长度elongation 作工硬化work hardening作功work done作图线construction line低密聚乙烯low density polyethylene (LDPE)低通滤波器low-pass filter低电压low voltage低碳钢low carbon steel布置layout免油轴承oil-less bearing冷加工；冷作工cold working冷加工硬化cold work hardening冷色cool colour冷轧压cold rolling冷却系统cooling system冷却效应cooling effect冷却液流量coolant rate冷凝胶；环氧树脂epoxy resin利口；「披」口；铁屑burr刨平planing刨花板；碎料板particle board吹风机air blower吹气模塑；吹模塑blow moulding吹管blow pipe含铁金属ferrous metal含水量moisture content坑凿cross-cut chisel均方根值root mean square value均角投影图；等角投影图isometric drawing 均速圆周运动uniform circular motion夹；夹钳clamp夹cramp夹卡mounting board夹具fixture; jig夹具及固定装置jig and fixture夹板；胶合板plywood夹持工具clamping device; holding tool夹背锯；榫锯tenon saw夹头chuck夹头开启匙；夹头扳手chuck key夹迭黏合成形lamination尾座tailstock床身；床道lathe bed床鞍；刀座帷apron形心；面心centroid形状shape形变deformation「快把」板；硬质纤维板hardboard快速移位rapid traverse抗扭强度torsional strength抗屈强度bending strength; yield strength 抗性分量；无功分量reactive component 抗拉强度tensile strength抗氧化剂anti-oxidant抗剪强度shearing strength抗磁性物料diamagnetic material抗挠性stiffness抗压强度compressive strength抗断强度breaking strength技术员；技师technician扶架steady扭力torsion扭矩；转矩torque扭转torsion扭转角angle of torsion把手hand grip扼流圈choke扳手spanner; wrench投影projection投影面projection plane投影线projection line攻丝tap材料material材料单；材料表material list杜拉铝duralumin杉木spruce步进电动机stepper motor步冲轮廓法nibbling每分钟转数revolution per minute (r.p.m.) 系统组件system component角托架angle bracket角位移angular displacement角板；直角板angle plate角度angle角榫corner angle joint; corner joint角铁angle iron谷巴凡立水cobal varnish车刀架tool holder 车床lathe车床工具lathe tools车床中心钻咀lathe centre bit车床操作法lathe operation车削；车旋lathe turning; turning车削工具turning tools防火胶板Formica防锈rust prevention防声耳筒；护耳器ear-protector防松螺帽lock nut防护装置；保护罩；保护网guard; safety guard八画注射成形法；喷射铸造法injection moulding 并激电动机；并绕电动机shunt-wound motor奶酪胶casein glue乳胶漆emulsion paint亚加力；压克力；聚甲基丙烯酸甲脂acrylics; polymethyl methacrylate (PMMA)亚稳态的；介稳态的metastable来回摆动oscillating两点透视two-point perspective刻度；划线ruling刺冲dot punch刮刀scraper刮擦scraping制动鼓drum brake制动碟disc brake制动器brake受迫振动forced vibration受迫振荡forced oscillation和谐harmony周转齿轮；行星齿轮epicyclic gear固定夹；台夹bench holdfast固定负载dead load定子stator定位销；合钉dowel定位螺丝set screw定距轮stitch marker屈片机folding machine屈曲bending屈服点；降服点yield point屈圈法loop forming屈卷法scrolling屈接缝folded lap seam屈喉机tube bender屈折folding屈折线folding line屈压接缝folded & grooved seam延性ductility延性的ductile弦锯法plain sawing弧口凿；圆凿gouge往复式运动reciprocatory motion拉力tensile force拉力计；张力计tensiometer; tensometer拉钉blind rivet; pop rivet拉钉接合blind riveting; pop riveting拉钉钳blind riveting pliers; pop riveting pliers拉张tension拉张应力tensile stress拉张应变tensile strain拉细drawing-down拉制法drawing拉线wire drawing「披」口；利口；铁屑burr拔钳nippers抛光buffing抛光机buffing machine放大；扩大enlargement放大尺pantograph放大倍数amplification factor放大器amplifier放电极加工；火花电蚀法electrical discharge machining易用万能尺line setter易碎fragile〈绘画的〉明暗运用；描影shading枝；杆rod杯形顶尖cup centre杯头螺丝hexagonal socket head cap screw 板锯panel saw松木pine松节水turpentine 法式磨光French polishing法拉〈电容量单位〉farad油石；磨刀石oil stone油漆；涂料paint泡沫塑料；多孔塑料；海绵状塑料foam plastics物理特性physical property物理属性physical attribute物理量physical quantity盲孔；闭孔；不贯穿孔blind hole直尺ruler; straight rule直角叉榫corner bridle joint直角尺try square直角板；角板angle plate直角杠杆bell crank lever直身钻嘴straight shank drill直车刀架straight tool holder直流发电机 d.c. generator直流电流direct current (d.c.)直流电动机；直流马达 d.c. motor直纹锯rip saw直线切削linear interpolation直线运动rectilinear motion直边凿；方边凿firmer chisel直铁剪straight snips硅silicon空行程idle stroke空气动力学aerodynamics空间space空载no load花纹凿embossing stamp花梨木rosewood花样；图案pattern虎克定律Hooke's Law虎钳vice虎钳护罩vice clamp初步意念proposed solution表面surface表面展开图surface development表面张力surface tension表面处理surface finishing; surface treatment 表面硬化case hardening表面硬化钢case-hardened steel表达方式presentation表达技巧；传意技巧communication technique表观膨胀；视膨胀apparent expansion金工metalwork金工工作间metalwork area金工角尺engineering square金工车床metalwork lathe金工虎钳engineer's vice金工锯床power hacksaw金属包头；金属箍ferrule金属配件metal fittings金属线wire金属压展机hand rolling mill金属擦光剂；磨光剂metal polish金属薄片sheet metal金属键metallic bond长方通rectangular tube长刨trying plane长螺旋钻咀long auger bit长镗孔long boring闸极gate阻抗impedance附件attachment附录appendices青铜bronze非反相放大器non-inverting amplifier非本征半导体extrinsic semicon。
飞机维修术语(英汉)
维修术语（灯）不亮not come on 不可用not serviceable “工”型type I 不锈钢stainless steel APU 舱门APU bay door 部件partT 型件Tee extrusion 材料material阿罗钉alodine 参考reference安全带safety belt 餐板feed panel安装install 餐车diner安装座attach fitting 操纵control按钮button 操作检查operational按需要as required 槽spout凹槽notch 侧板sidewall凹坑dent 测量measure把手,扶手handle 测试test包皮cowl 插钉pin保护层coating 插头plug保险fuse 插座receptacle报废discard 拆下remove报告工程师report to engineer 长桁stringer杯子cup 超标out of limit比率转换器ratio changer 超标exceed the limit 壁橱closet 超过exceed边缘edge 超控手柄override handle便于检查easily to inspect 彻底修理drastically repair 变形deformation (n) 陈旧的worn变形deform (v) 衬板liner变压器transformer 衬套bush标牌placard 成型shaping标识sign 乘务员attendant标志instruction 尺寸size玻璃pane 充足的sufficient玻璃纤维fiberglass 冲水按钮flush button补片patch 冲洗flush补片filler 冲压ram冲压空气ram air 低压压气机LP-compressor 抽油defuel 底部bottom出口exit 底盘base除腐区reworked area 底漆primer厨房galley 底座（结构件）mounting厨房烤箱galley oven 底座（螺母）plate储物柜closet 底座（天线）base处理treatment 地板梁floor beam处理dispose 地面ground传感器sensor 地毯carpet传输transmission 第二层two layer垂直的vertical 点火电嘴ignitor存放处location 电路circuit错位migration 电门，开关switch搭地线jumper 电气electrical搭接处interface 电气接地ELEC bonding搭接片splice strap 电源通电power搭接片splice 电子avionics打磨blend out 电子架 E rack打磨片blent disk 电子架shelf打止裂孔drill stop hole 电阻elec resistance大翼wing 电阻resistance大于more than 垫片washer单向活门check-valve 吊仓nacelle弹簧片spring seal 吊点mount cone挡块retainer 调节adjust挡雨板fender 调整片tap导线wire 顶板ceiling灯light 顶部top灯泡bulb 顶部overhead灯泡lamp 定中弹簧decentering spring 灯箱light case 丢失miss灯罩light lens 堵盖plug登机门ENTRY DOOR 堵塞clog端头ending 腐蚀corrosion段section 腐蚀corrode断break 附件（大）accessary断开disconnect 附件（小）attach断裂fracture 附近adjacent to断裂的broken 复合complex断丝,磨损fray 副驾驶员做椅first offcer's seat锻件forged part 副翼aileron多处numerous 改装modification发动机engine 盖cap翻新overhaul 杆rod反光镜mirror 钢丝steel方向舵rudder 钢索cable防冰管anti-ice duck 割除cut out防腐corrosion-inhibition 割断，割下cut off防静电static-free 隔板clapboard,partition防磨条wear strip 隔框bulkhead防滞antiskid 隔热棉insulation-blanket防撞灯anti-collision light 隔栅grille放extend 各有each has放电刷discharger 根据方案in according to disposition 分层delamination 根据监控指令单condition monitor order…风层,脱胶delaminate 更换replace风挡windshield 工程师engineer风挡玻璃windscreen 功能测试functional test风扇整流罩FAN COWL 功能检查functional风蚀erode 供应系统feed system封严sealing 供油管OIL TUBE封严条seal 鼓轮drum蜂窝芯stagger core 鼓起bulge扶手armrest 固定secure扶手盖板armrest cover 固化harden辅助滑轨assistant track 固化剂hardener故障fault 划痕，划伤scratch刮伤scratch 划窝countersink挂attach 环氧树脂epoxy resin挂钩hook 恢复restore挂上hang up 活动窗slide window关上close 活门valve观察镜view glass 货舱cargo compt观察镜viewer 机构mechanism观察员observer 机身fuselage观察员observer 迹象mark光滑地smoothly 加强doubling滚轮roller 加强件stiffener过道aisle 加强块doubler过期expire 加强肋intercostal过热传感元件overheat sensing element 加强修理reinforcement海绵sponge 加温导线hot wire焊接weld 加油面板refuel panel焊条welding rod 加油站面板fueling station panel 恒速传动装置CSD case 夹子clip横梁latitudinal beam 驾驶舱cockpit横向lateral 间隙gap后端rear 减速板speedbreak后缘T/E 减压器reducer厚度thickness 减震器shock absorber呼叫灯call light 减震支柱shock strut护板protect strap 检查inspect护目镜goggles 检修门access door 护罩shroud 胶sealant花键spline 胶带tape滑轨track 胶垫mat滑轮pulley 胶垫圈rubber washer 滑丝cross thread 胶套rubber滑梯罩slide cover 胶纸tape滑油量oil lever 角材angler角型件angle shape 喇叭megaphone 脚登板pedal 拦网block铰链hinge 牢固性security接地点ground point 老化aged接耳lug 老化,退化deteriorate接通，提供supply 雷达罩radome接头fitting 肋rib接线管splice 离合器clutch接线片terminal lug 立柱pole结构的structural 例行routine金属屑metal particle 连杆link襟翼flap 连接attatch紧固件fastener 连接板attach plate 紧急出口exit 连接口coupling进气道inlet duct 连接销lockwire进气口inlet port 联锁interlock径向驱动轴radial drive shaft 裂crack静电，静压static 另一个another救生衣lifevest 龙骨梁keel beam咖啡壶coffee maker 滤网filter卡箍clamp 铝箔foil卡环collar 轮舱wheel well开口销cotter pin 轮子wheel靠背back panel 逻辑logic壳体case 螺钉screw可用available 螺钉孔screw hole客舱cabin 螺杆bolt空气循环隔栅air return grille 螺帽nut口port 螺套insert块piece 螺纹压伤cross threading 框架frame 马桶toilet垃圾箱dustbin 慢车IDLE拉紧pull 毛刺bur毛胚件rough 破损damage铆钉rivet 漆层coating门槛sill 其中之一one of门框door frame 启动活门start valve蒙皮skin 启动机starter密度density 起落架landing gear 密度计densitometer 气瓶cylinder面板panel 千层片shim面漆enamel 前厕所fwd lav模糊blur 前缘L/E模糊不清obscure 腔体cavity磨损wear 墙纸wallpaper目视visual 切口cutout内侧interior board 勤务面板service panel内层inner 轻度light尼龙搭扣nylon fastener 轻微slight尼龙扣nylon hook 清洁clean拧紧tighten 清洁剂cleaner扭力管torsional tube 区域zone扭曲kink 曲柄crank排row 去除深度remove depth排放drain 去毛刺deburr排水槽gutter 缺口nick排水管drain tube 群边skirt edge配平trim 燃油fuel喷漆paint 燃油泵fuel pump喷砂sand blast 扰流板spoiler皮带，片strap 热水器water boiler皮托管pitot 人工行程限制manual travel limit 偏航阻尼器yaw damper 日光灯daylight lamp平衡机构equalizer 软管，软护套hose平滑的，使平滑smooth 润滑剂lubricant平行balance 三段three section散装bulk 逃离滑梯escape slide刹车brake 天花板ceiling上表面upper surface 天线antenna上述above 填补fill深度depth 跳开关breaker渗漏leakage 凸轮cam升降舵elevator 图纸DWG绳rope 涂，粘贴apply失效inoperative 退漆strip paint湿安装wet installed 退色badly faded试车run up 托板pallet释压pressure-release 托板螺帽plate nut收retract 脱开disengage收发机tranceiver 外outer手柄towing lever 外侧outer board手册manual 完成complete手电torch 完成finish手工handwork 万向接头gimbal手提的portable 维护maintain手提灭火瓶extinguish bottle 尾部tail树脂resin 尾舱tail compartment 双倍double 尾喷管exhaust nozzle 水平安定面horizontal stabilizer 尾锥TAIL CONE撕裂tear 位置locate伺服servo 温度temp松动，松脱loose 涡杆jackscrew送修send to repair 涡杆worm bolt塑料plastic 涡轮turbine随动盖板hinge access door 污染物contamination 锁lock 污物dirt锁定lockout 无线电高度表radio altimeter锁扣latch 稀释剂thinner锁销lockpin 铣mill系统system 溢出spill下部lower 翼尖tip下角LWR corner 翼间wing tip下位锁downlock 翼梁spar下陷concave 引进introduce下缘条chord 引孔make guiding hole 纤维板fibre board 引孔drill hole相关的relative 引气bleed相磨chafe 引气管bleed hose消音板accoustic panel 应急emergency销子pin 永久性修理permanence repair 楔形块wedge 用…填补fill it up with…信号灯annunciator 油封preservation行李架luggage-rack 油箱fuel tank行李箱stowage 游动梁walk beam修边reform 雨刮wiper修理repair 语音记录器voice recorder锈蚀rust 预冷器precooler循环cycle 预位ARM压紧gland 原厚度original thickness 压力通风系统plenum system 原来originally压条cover 阅读灯reading light严重的serious 允许损伤allowable damage阳极化anodize 杂志袋literature container 氧气oxygen 载荷调整preload adjust氧气面罩oxygen mask 再循环recirculation液压HYD 在位be in place液压泵HYD PUMP 脏dirty液压管HYD duct 增压pressurization液压系统hydraulic system 增压泵boost pump液压油管组件TUBE ASSY 粘贴bond液压油箱hydraulic reservior 照明illuminate移到move to 遮阳板shade真空泵vacuum pump 自动刹车autobrake拯救salvation 自动油门auto thrust整流罩fairing 自锁螺帽jam nut整流锥spinner 自由移动move freely整形rework 总管manifold正常normal 纵梁longeron正常位置normal position 纵向longitudial正驾驶员座椅captain's seat 阻力支柱drag strut之间between 组件assembly,pack支撑架bracket 组件(电气) unit支撑座support mount 组件(机械) assy支架bracket 最薄min thickness支拄support 作动筒actuator止动固定块stop block 坐垫cushion止动块atopper 座椅seat指点信标marker beacon antenna 注意caution指示indication 转接器adapter制作fabricate 转弯灯runway turnoff light 中厕所mid lav 转向turn中间，中央center 装饰条trim strip周围around 准备prepare轴shaft 着陆灯landing light轴承bearing 自动关闭auto close主轮main wheel 助推机构扳机power assist triggerCategories of DefectCategories of defect depends on experience of maintenance practic e .In this manual, the defaultMethod used to categorize the defect found on the aircraft into fou r areas. Structure defect , Material defect, Common parts and Compo nents defect and General defect.缺陷分类缺陷的分类一般依照维修实践中的经验来分。
航空专业英语常用工具
Install the brake unit (1) on the wheel axle (6) with the HOISTING DEVICE (F27220000) or HANDLING TOOL (1324A) .
钳子 Pliers
保险钳Safety Wire Twisters
剪钳 Diagonal Cutters
尖嘴钳Needle Nose Pliers
大力钳 Locking Pliers
尖嘴大力钳 Needle Nose Locking Pliers
螃蟹头 Crowfoot
锤子 Hammer
Lightly hit the outer edge of the QAD adapter with a softface hammer.
使用软面锤子轻敲 QAD 适配器的外侧边缘。
常用句式 1.Do/Execute a procedure/step with/by some tool.
Do a running torque check of the nuts with a torque wrench.
Translation Exercises
1.轻轻的用油脂 04022 润滑保护工具的外圆周。 Slightly lubricate the outer circumference of
the protective tool with Material No.04022 (COMMON GREASE (Material No. 04-022)).
气压表 Barometer
冲子 Punch
铁冲 铝冲
OPEN-END 开口
BOX-END 梅花
飞机维修工具大汇总——中英文对照图文版，值得每一个机务收藏！
飞机维修工具大汇总——中英文对照图文版，值得每一个机务收藏！展开全文1.一字螺丝刀———Flat tipScrewdriver2.十字螺丝刀———Philipshead Screwdriver3.螺母螺刀———Nut Screwdriver4.卡拉螺刀——ratcheting magnetic Screwdriver5.短螺刀——Stubby Screwdriver6.仪表螺刀——Electronic miniature Screwdrivers7.弯头十字/一字螺刀——Offset Screwdrivers8.鱼口钳—— Combination Slip-Joint Pliers9.剪钳—— Diagonal Cutters10.保险钳——Wire Twister（PS：超爱这把小钳子，打出来的保险均匀紧致，实在是强迫症机务的最大福音！！）11.鹰嘴钳——Adjustable Joint / Alligator Pliers12.插头钳——Connector Pliers(如果插头拧不动，又不能用蛮力的时候，就该它上场啦~~温和保护，轻轻一拧，插头就下来啦)13.尖嘴钳——Needle Nose Pliers14.鸭嘴钳——Duck Bill Pliers15.剪线钳——Bolt Cutters/ Pliers16.大力钳——Locking Pliers, Vise-Grip(当拆的家伙实在顽固，我们只能召唤大力水手啦~~看你得瑟~~哼哼~~不过大力钳会产生一定的伤害哦~）17.锁定夹——Locking Clamp18.C型夹——C-Clamps19.卡环钳——Retaining Ring Pliers卡环有内卡环和外卡环，所以，卡环钳也有内卡环钳和外卡环钳20.剥线钳——Wire Crimper/ Stripper/ Cutter21.焊枪、烙铁——Soldering Gun/ Iron22.开口扳手——Open end Wrench23.弯头梅花扳手——Box Wrench24.开口梅花扳手——Combination Open-Box Wrench25.S型梅花扳手——‘S’ Shaped Box Wrench26.半月型组合扳手——Half Moon Box Wrench27.片卡拉——RatchetingBox Wrench28.套筒扳——Socket Wrench29.活动板——AdjustableWrench/Single Open Ended Spanner30.套装内六角——Hex (Allen Keys) Wrench31.L型内六角——Hex L Shaped (Allen Keys) Wrench,32.片开口——Crowfoot Open End Wrench33.梅花片开口——Crowfoot Flare Nut Wrench34.链条扳——Chain Wrench35.皮带扳——Strap Wrench36.管子扳——Pipe Wrench37.管子扳（活钩扳手）——Adjustable Hook Spanner Wrench大家看它的英文名儿里的Hook，是不是想起来“小飞侠彼得潘”里的Hook船长，他的手就是个钩子嘛~~额。
飞机航空机务维修工具航材英语-中英对照上传
2015年1月6日
Repair 修理
2015年1月6日
2015年1月6日
doubler 加强板 patch 补片 cutout 切口 cutout/cutting line 切割线 fastener spacing/pitch 紧固件间距 edge distance/margin (紧固件) 边距
机身为半硬壳结构，轻质合金的环形隔框和纵 向长桁支撑并加强了主要机身蒙皮。
2015年1月6日
Damage 损伤
2015年1月6日
scratch 划痕 gouge 凿痕 crack 裂纹 dent 凹坑 distortion 变形 corrosion 腐蚀
2015年1月6日
部件的材料、功能和位置决定了用于该部件上 的防护处理类型。
2015年1月6日
Skin stiffeners make the fuselage skin stronger and are riveted to the skin in areas of high stress (door openings, emergency exits, cabin windows, etc.).
检查货舱门可操纵、关严锁住且封严密封完好 。目视检查货舱内地板无严重压坑、破裂及腐 蚀。
2015年1月6日
Damage which exceeds the 'Allowable Damage' limits can be repaired by cutting out the damaged area of a structural component and inserting or attaching a reinforcing piece.
航空维修相关中英文对照
AMMAircraft Maintenance Manual飞机维护手册飞机制造商按照各机型编写的维修手册，是航空公司编写自己工卡的重要依据。
CMMComponent Maintenance Manual部件维修手册飞机制造商按照各机型编写的部件维修手册。
EMMEngine Maintenance Manual发动机维修手册
MMELMaster Minimum Equipment List主最低设备清单MMEL是由航空器制造国的民航当局、适航机构制订的，用于指导航空器用户、航空公司具体编写MEL的纲领性文件，它规定了该型号飞机允许带有哪些不工作的仪表和设备放行，并对工作仪表设备的最低放行数量以及保留故障放行的限制条款作出了原则上的要求。
ATAAir Transport Association of America美国航空运输协会
CAACGeneral Administration of Civil Aviation of China中国民用航空总局
EASAEuropean Aviation Safety Agency欧州航空安全局
EM工程部负责各种手册资料的管理，工程文件的颁发及监控。
PM维修部负责维修计划及工程文件的执行。
MM航材部负责航空公司正常运营所需的航材保障。
其他
ALIAirworthiness Limitation Item适航限定项目通常与CMR一起作为MRBR的附件，是航空公司制定维修计划的基础之一。
MROMaintenance Repair Overhaul/Maintenance Repair Operation
FAAFederal Aviation dministration美国联邦适航当局
ISCIndustry Steering Committee工业指导委员会由航空器、发动机、螺旋桨、设备制造人及航空运营人的代表组成。其任务是研究并制定MRBR建议书的政策和程序手册（PPH）、指导工作小组（WG）的工作，准备MRBR建议书。它受由航空器制造人和航空运营人推荐产生的ISC主席领导。
飞机维修部件中英文学习
飞机维修部件中英文学习 2007-7-23 11:12 信息来源：互联网中文名称 英文名称单向活门 One-Way Valve 快速热水器 Rapid Water Heater 安全活门 Safety valve高压级调节活门 High stage pilot 高压级引气活门 High stage regulator 引气调节器 Bleed air regulator反流检查控制活门 Reverse Flow Check Control Valve 过滤型压差调节器 Filter type differential pressure regulator 四英寸直径气动蝶形关断活门 Four inch diameter pneumatic butterfly shutoff valve 马桶组件 Toilet assembly 冲洗活门组件 Flush Valve Assy圆顶灯 Dome Light 真空马桶组件 Vacuum toilet assemblies 活门组件 Valve Assy 冲水马桶组件 Flushing toilet assembly排水活门组件 Holders of drain valve assembly控制显示组件 Control/Display Unit飞行管理计算机 Flight Management Computer 防冰活门 Nose cowl thermal anti-ice valve液晶控制显示组件 Liquid Crystal DisplayControl/Display Unit 热交换器 Heat exchanger初级热交换器 Primary heat exchanger 货舱动力驱动组件 Cargo Powered Drive Unit发动机仪表系统次显示板 E.I.S secondary display panel 58加仑真空污水箱 58 Gallon vaccum waste tanks50A 不可调变压整流器 Transformer-Rectifier,50 AMP Unregulated 直流转接盒 DC Junction Box风档温度控制器 Windshield Temperature Controller窗户和空速管加热模件组件P5-9 Window and Pitot Heat Module Assembly,P5-9燃油控制模件组件P5-2 Fule control module assy.p5-2电源管理控制模件组件P5-68 Power management control module assy.交流系统发电机/APU模件组件P5-4 AC System Generator/APU ModuleP5-4 Assembly发电机驱动和备用电源模件组件P5-5 Generator Drive and Standby Power Module Assembly,P5-5发电机驱动和备用电源模件组件P5-6 Generator Drive and Standby Power Module Assembly,P5-5发电机驱动和备用电源模件组件P5-7 Generator Drive and Standby Power Module Assembly,P5-5飞行记录和马赫空速警告模件组件P5-19 Flight Recorder and Mach Airspeed Warning Module Assyembly,P5-19飞行控制模件组件P5-3 Flignt Control Module Assembly P5-3烤箱Oven俯仰计算机Pitch Computer变压整流组件Transformer Rectifier Unit发动机附加组件Engine Accessory Unit Assembly仪表着陆控制板组件ILS Control Panel Assy.特高频全向导航控制板组件VOR Control Panel Assy.机翼位置航行灯Wing Position Navigation Light飞机航行防撞频闪灯Aircraft Navigational，'Anti-collision Strobe Light高亮度飞机识别灯High Intensity Aircraft Recognition Light飞机尾翼闪光灯Aircraft Tail Position Light，Flashtube飞机后位置航行灯Aircraft Navigational Light-rear position后位置灯组件Rear Position Light Assembly上机身防撞灯Upper Fuselage Anti-Collision Light下机身防撞灯Lower Fuselage Anti-Collision Light发动机仪表系统主显示板 E.I.S Primary Display Panel马达泵过滤器组件Motor-pump-filter unit assembly压力调节活门Pneumatic Pressure Regulating Valve压力调节和关断活门Pressure regulating and shutoff valve高压级引气调节器High stage valve双效用活门Dual purpose valve机头罩防冰活门Nose Cowl Anti-lce Valve预冷器冷却空气调节活门Four inch diameter precooler control valve预冷器冷却空气调节门Modulating pre-cooler air valve第十四级调节活门Fourteenth stage pilot驾驶舱灯Cockpit Light压差调节器One and One-half inch diameter turbofan control shutoff differential pressure regulator流量活门Flow control valve5英寸直径流量控制活门Five inch diameter flow control valve流量控制和关断活门Flow control and shuttoff valve3 1/2英寸直径流量控制活门Three and one half inch diamter flow control valve3 1/2英寸直径电动控制双向调节和关断蝶形活门Three and one half inch diamter flow controlvalve electric dual modulating and shutoff butterfly valve电瓶充电器Battery Charger偏航阻尼耦合器Yaw Damper Coupler大气数据计算机Air Data Computer天花板灯Ceiling Light飞行控制计算机Flight Control Computer方式控制板Mode Control Panel行李箱扭矩臂组件Center Overhead Stowage Bin Upper Arm Torque Tube Assembly防滞/自动刹车控制组件AntiSkid/Autobrake Control Unit防滞刹车控制组件Skid Control Unit刹车系统控制组件Brake System Control Unit着陆灯Landing Light收放着陆灯Retractable Landing Light回收箱挡块组件Retractable Container Stop Assembly发动机火警,过热,'APU火警控制模件Control Module,Engine Fire,Overheat & APU Fire翼尖航行灯Wing Tip Navigation Light频闪灯电源Strobe Power Supply水壶Water Boiler组件/区域温度控制器Pack/Zone Temperture Controller客仓区域温度控制器Cabin Zone Temperature Controller组件温度控制器Pack Temperature Controller马达驱动风扇Motor Driven Fan座舱空气循环风扇Cabin air recirculation fan信号灯组件Indicator Light AssemblyAPU 控制组件M820 APU Control Aassembly M280APU 控制组件APU Control Unit Assembly空调辅助组件M324 Air Conditioning Accessory Unit Assembly M324综合飞行系统辅助组件Integrated Fight System Accessory UMA轴流式风扇组件Vaneaxial Fan Assembly发动机振动监控器Engine Vibraction Monitor马达操纵关断活门Motor Operated Air Shutoff Valve发动机和APU火警控制模件组件P8-1 Engine and APU Fire Control Module Assembly P8-1 液压泵模件组件P5-8 Hydraulic Pumps Module Assembly P5-8空调模件组件Air Conditioning Module Assembly发动机及机翼防冰模件组件P5-11 Engine and Wing Anti-ice Module Assembly.P5-11客舱温度模件组件P5-17 Cabin Temperature Module AssemblyP5-17燃油系统模件组件P5-2 Fuel System Module Assembly P5-2窗户及全-静压空速管加热模件P5-9 Window and Combind Pitot-Static Heat Module Assembly P5-9窗户及全-静压空速管加热模件Window and Combind Pitot-Static Heat Module Assembly P5-9 IRS 方式选择模件组件IRS Mode Selector Module Assembly压力控制板Pressure Control Panel快速烤箱DF700LH High Speed Oven DF 700LH蒸汽烤箱Steam Oven高速烤箱High Speed OvenDR4100系列热水器Water Heater DR4100 Series活门High Stage Bleed Valve汇流条电源控制组件Bus Power Control Unit流量控制活门Flow Control Valve自动油门计算机Autothrottle Computer压力控制器Pressure Controller流量和关断活门Flow control and shutoff valve高压控制器High Pressure Controller真空抽气马桶Vacuum toilet assembly滑油箱Lubricating oil tank接近电门电子组件Proximity Switch Electronics Unit高压关断活门High Pressure Shutoff Valve咖啡壶组件Coffeemaker Assembly蒸气烤箱Steam Oven风档加温控制器Window Heat Controller凤挡加热控制组件Window Heat Control Unit烤箱组件Oven Aseemblies发动机超温火警探测器Engine Overheat and Fire Detection Unit麦克风Micophone发电机控制组件Generator Control Unit汇流条保护板Bus Protection Panel风扇活门Fan Air Valve高压流量控制活门High Pressure Bleed Control Valve清水箱Potable Water Tank数字/模拟转接器Digital/Analog Adapter串行摆动飞机航行灯Tandem Oscillating Aircraft Navigational Light数字式大气数据计算机Digital Air Data Computer马桶真空泵Vacuum Generator飞机头戴式耳机Aircraft Headsets自动关闭水开关组件Fancet Assy-self close放音机Wall Mount Type Prerecorded固态壁挂式预录通告和登机音乐磁带放音机SOLID-STATE WALL MOUNT PRAM。
飞机常用单词英汉对照
航空英语证书考试(PEC)-航空飞行器词汇Acquisition Time: 初始定位时间Active Leg: 激活航线Adapter: 转接器、拾音器、接合器Airborne: 空运的、空降的、机载的、通过无线电传播的Alkaline: 碱性的、碱性Almanac: 历书、概略星历Anti-Spoofing: 反电子欺骗Artwork: 工艺、工艺图、原图ssAtomic Clock: 原子钟Auto-controlling: 自动控制Avionics: 航空电子工学;电子设备Azimuth: 方位角、方位(从当前位置到目的地的方向)Beacon: 信标Bearing: 方向，方位(从当前位置到目的地的方向) Bug: 故障、缺陷、干扰、雷达位置测定器、窃听器Built-in: 内置的、嵌入的Cellular: 单元的、格网的、蜂窝的、网眼的Cinderella: 水晶鞋、灰姑娘这里特指JA V AD GPS接收机OEM板的选项，能自动在隔周的星期二GPS午夜时刻开始的24小时内让您的Javad接收机和OEM板变为双频双系统。
Coarse Acquisition Code(C/A): 粗捕获码Cold Start: 冷启动Connector: 接头、插头、转接器Constellation: 星座Control Segment: 控制部分Converter: 转换器、交换器、换能器、变频管、变频器、转换反应堆Coordinate: 坐标Co-pilot: 飞机副驾驶Cost-effective: 成本低，收效大的Course: 路线、路程、航线Course Deviation Indicator (CDI): 航线偏航指示Course Made Good (CMG): 从起点到当前位置的方位Course Over Ground (COG): 对地航向Course To Steer(CTS): 到目的地的最佳行驶方向Crosstrack Error (XTE/XTK): 偏航De-emphasis: 去矫、去加重Definition: 清晰度Diagonal: 对角线、斜的、对角线的Distinguishability: 分辨率Dropping resistors: 减压电阻器、将压电阻器Datum: 基准Desired Track (DTK): 期望航线(从起点到终点的路线)Differential GPS (DGPS): 差分GPSDilution of Precision (DOP): 精度衰减因子Elevation: 海拔、标高、高度、仰角、垂直切面、正观图manned flight 有人驾驶的飞机aerodynamics 空气动力学cambered surface 弧面，弯曲面characteristic 性能，特性drawing 图纸glider 滑翔机lift 升力model 模型，样机structure 结构，构造transportation 运输；运输工具wing 机翼biplane 双翼机control v. 操纵，控制，驾驶rib 肋，翼肋cloth fabric 布织物lifting surface 升力面girder 桁架，构架，机架，骨架bamboo 竹材strip 带状物，狭片，长条，简易机场，跑道piano wire 钢琴丝auxiliary surface 辅助翼面stability 安定性，稳定性configuration 外形，形状，结构，构造型式，布局truss type structure 桁架式结构strut 支柱，支撑wire-braced wing 张线支撑的机翼cockpit 飞机驾驶舱fabric-covered body 织物覆盖的机体fuselage 机身engine 引擎，发动机tail 尾部strong lightweight structure 坚固的轻型结构resistance 反抗，抵抗，阻力，阻尼，电阻friction 摩擦，摩擦力potential speed 潜在速度strength 强度plane 飞机designer 设计者superstructure 上层结构，上部结构wooden former 木质翼肋，木质隔框stringer 桁条，长桁smooth streamline shape 光滑流线型welded thin-wall steel tubing 焊接的薄壁钢管stressed-skin structure 承力蒙皮结构plywood eggshell-like structure 层板薄壳式结构laminated wood ring 层半框架，胶合板框架landing gear 起落架aluminum-alloy sheet 铝合金板monocoque structure 硬壳结构all-metal aircraft 全金属飞机semi-monocoque structure 半硬壳式结构rigidity 刚度structural challenge 结构方面的困难（挑战）high-altitude flight 高空飞行mysterious adj. 神秘的，费解的fatigue 疲劳pressurization and depressurization cycle 增压减压循环fail-safe construction 破损安全结构rip-stop doubler 止裂加强板strategic location 关键部分crack 裂纹structural component 结构部件stress 应力aviation maintenance technician 航空维修技师aircraft structure 飞机结构control surface 操纵面，舵面stabilizer 安定面flap 襟翼trim tab 调整片spoiler 扰流板，阻流板，气流防护板rudder 方向舵attitude 状态，姿态，姿势compression 压缩，压力tension 拉伸，拉里，张力torsion 扭曲，扭转，扭力，扭转bending 弯曲，挠曲shear 剪切，剪力，切变，切力definition 定义，阐明，确定，明确crush v. 压碎，击碎，牙边，挤压press v. 压缩，冲压，挤，推stretch v. 伸展，伸长，拉紧，延伸cable 钢索bolt 螺栓material 材料layer 层，夹层，薄片，条river 铆钉tensile force 拉力overstressing 过度应力，超限应力permanent deformation 永久变形strain v. 硬变，变形，延伸率，过度使用airworthy adj. 适航的，飞行性能好的assembly 组合，装配，总装组件，部件，装配件stress analysis 应力分析performance 性能，特性，行为，表现，实行，实施，完成，操作specification 详细说明，技术规格，技术条件，说明书danger 危险failure 失败，故障，事故，破坏，断裂nomenclature 术语，专用名称aileron 副翼trailing edge 后翼wing tip 机翼翼端roll v. 滚转，横滚，滑跑lifting force 升力jet airplane 喷气式飞机cruise speed 巡航速度approach speed 进场着陆速度，进近速度landing speed 着陆速度，接地速度chord line 弦线angle of incidence 安装角airfoil 翼型，翼剖面，机翼，翼面，气动力面longitudinal axis 纵轴stabilizer setting angle 安定面安装角horizontal stabilizer 水平安定面vertical stabilizer 垂直安定面sweep angle 后掠角reference line 参考线horizontal axis 水平轴线antidrag wire 反阻力张线（承受与飞行阻力相反的惯性力的对角张线）leading edge 前缘antilift wire 反升力张线balanced control surface 平衡操纵面equilibrium 平衡状态hinge axis 铰链轴static condition 静止状态beltframe 连接隔框skin 蒙皮frame 框，隔框，壁板式隔框boom (tailboom) 尾撑,尾梁built-up structure 组合结构，拼装结构cabin 机舱，客舱helicopter 直升机rotor 转子，叶轮，旋翼tail rotor 尾桨power train 动力系列compartment 隔舱，舱，隔间，室former 隔框，翼肋，维型框，假肋cabane 顶架canard 鸭式飞机，鸭式布局，鸭式翼，前置平尾，前舵cantilever beam 悬臂梁external bracing 外部支撑center section 中翼，中段outer wing panel 外翼段passenger 旅客，乘客cabin airplane 闭舱式飞机cockpit canopy 座舱盖，驾驶舱盖control cable 操纵钢索control lever (control stick) 驾驶杆，操纵杆longitudinal control surface 纵向操纵面lateral control surface 横向操纵面，横侧操纵面elevator 升降舵ruddervator 方向升降舵（V型尾翼的）control wheel 驾驶盘semiwheel 半盘式cowling 整流罩，包皮，防护罩removable cover 可卸口盖decalage 翼差角dihedral angle 上反角drag strut 阻力支柱（在布制蒙皮机翼结构中，用以支持阻力张线的加强肋）阻力杆（起落架前拉杆和后撑杆）drag wire 阻力张线pitching movement 俯仰运动elevon 升降副翼all-wing aircraft 三角翼飞机fairing 整流罩，整流装置streamlined contour 流线型外形fireproof wall (fire-resistant wall) 防火墙gap 间隙，间隔，翼隔superposed airfoil 重叠机翼（双翼机获三翼机）stability 安定性，稳定性inspection door 检查口盖interplane strut 翼间支柱jury strut 辅助撑杆，副支柱，保险撑杆alighting gear 起落架，着陆装置propeller blade 螺旋桨桨叶lift wire (flying wire) 升力张线longeron 大梁（机身或短舱的）plating 重型金属蒙皮，表面镀层的金属板yawing movement 偏航运动pedal 脚蹬shock absorber 减震器，缓冲器slat 缝翼attack angle 攻角，冲角，迎角span 展长spanwise a. adj. 延机翼展向spar 机翼翼梁spinner 螺旋桨整流罩stagger 斜罩角compressor blade 压缩机叶片tandem-rotor helicopter 纵列式（双旋桨）直升机stagger wire 斜罩张线sweepback 后掠角antitorque rotor 尾桨，反扭矩尾桨tail skid 尾撬，尾部保护座tail wheel 尾轮chordwise adj. 弦向auxiliary fuel tank 副油箱，辅助油箱antenna 天线anti-collision light 防撞灯stair door 登机梯舱门engine nacelle 发动机短舱deicer boot 除冰带navigation light 航行灯construction 结构，构造longitudinal member 纵向构件bending stress 弯曲应力landing 着陆，接地，降落__cantilever wing 悬臂机翼，张臂机翼high-performance aircraft 高性能飞机external strut 外撑杆basic feature 基本特征beam 辆，横梁，柱monospar adj. 单梁，单梁的two-spar adj. 双梁，双梁的multispar 多梁，多梁的web （大梁）腹板，辅助梁，纵墙，肋板shear web 承减腹板spanwise member 翼展方向构件，展向构件high-wing monoplane 上单翼机tie rod 连干，系杆brace wire 张线drag load 阻力，阻力载荷built-up I beam 装配的I型梁，组合的I型梁extruded I beam 挤压成型的I型梁plain rib 普通肋，平面肋chordwise member 弦向构件compression rib 抗压翼肋，加强翼肋cap strip 翼肋缘条solid plywood web 整体的层板（胶合板）腹板cross bracing 交叉撑杆，横撑杆gusset vt. 角撑，角撑板，装角撑板于nail vt. 铁钉，钉住，用钉钉牢stamped rib 模锻翼肋truss-type cross section 桁架式横截面stiffener 加强杆，加强板，加强件fabric covering 布制蒙皮plywood covering 胶合板蒙皮，层板蒙皮tubular member 管型构件formed rib 维型翼肋integral fuel bay 整体油箱attachment fitting 安装街头，连接接头inspection 检查service vt. 服务，使用，维护，维修，检查，保养frontspar 前梁butt-rib 根部翼肋，平端头翼肋flange vt. 翼梁缘条，凸缘，突缘，（在----- 上）安装突缘end bow 机翼端部弯曲部分nose rib 前缘翼肋trailing edge strip 后缘条aileron control cable 副翼操纵钢索aileron control bell crank 副翼操纵双摇臂，副翼操纵双摇臂曲板tape v. 布带，带子，用带系扎FWD fuselage fitting 机身前接头washer 垫圈，垫片nut 螺帽retainer 护圈，卡圈，挡板，保持器dowel pin 定位销，和缝销钉，暗钉fuel vent line 燃油系统通气管路door 舱门，口盖，入口plate 板，盘，口盖tab 调整片，补偿片，操纵片，标签aileron tab 副翼调整片position light 航行灯landing and taxi light 着陆滑行灯fuel filler door 燃油注油口pitot tube 空速管，全静压管，全压管stall warning unit 失速警告装置RAM air inlet 冲压空气进口Federal Aviation Administration 联邦航空管理局Advisory Circular 咨询通告jet airliner 喷气式班机，喷气式航线客机jet engine 喷气发动机section 剖面，截面，型材，段，区域，部分assembly jig 装配架，型架inboard wing 内翼age hardening 时效硬化dimension 尺寸，大小bending load 弯曲载荷tensional load 扭转载荷stretch press 张拉成型机airfoil surface 翼型表面die vt. 冲切，用模（压）成型，模子，冲模，压模jaw 夹紧装置______________，钳口，夹爪airfoil contour 翼型外形formed 7075 sheet 成型的7075钣tab segment 弓形薄片接头forging adj. 锻造件splice vt. 拼接，绞结，拼接板，绞结处junction 接合，接合处，连接点wing tank 机翼油箱sealing compound 密封剂，密封腻子，封口胶center line 中心线，中线mating adj. 配合，连接，配合的，相连platform 平台hydraulic cylinder 液压做动筒synthetic rubber 合成橡胶center wing 中翼outboard wing 外翼swept-wing 后略翼nacelle 吊舱，发动机短舱production break 工艺分离面wide-bodied airliner 宽机体客机flight control surface 飞行操纵面pylon 吊架main frame 承力构架，主构架，承力隔框torque box 承扭盒段auxiliary structure 辅助结构permanent type fastener 永久式紧固件butt-spliced 平头对接，平头拼装flush fastener 埋头紧固件honeycomb panel 蜂窝板interference-fit 经配合，干涉配合close-tolerance fastener 高精度公差紧固件play 浮动，间隙，游隙tolerance 配合公差，容差，加工裕度flap vane 开缝襟翼导流片exterior plate doubler 外部双重加强板slat track 缝翼滑轨can 筒型壳，密封外壳，包套crew 空乘人员，机组，空勤组cargo 货物controls 操纵系统item 项目，零件，产品（均指已列入清单的项目）streamline form 流线型式accessory adj. 附属的，辅助的，附件，辅助设备，部件carburetor 汽化器，化油器，增碳器magneto 磁电机ignition lead 点火器导线strainer 过滤器fuel line 燃油管道turnover 回转，循环，翻倒，倒置emergency exit 紧急出口capacity 容量，容剂，能力classification 分类，类别，归类assemblage 装配，安装，总装配件bar 杆，棒，条lateral bracing 横向支撑tubular fuselage member 管状机身构件interval 间隔，间隙，距离bay 隔间，隔舱，段diagonal member 斜构件，对角构件percentage 百分比，百分数，比率ring 环，圈，环形隔框bulging 膨胀，凸出，褶皱皮buckling 皱损，皱褶，波纹glue v. 胶，粘结剂，胶合，粘结aircraft-quality plywood 航空质量级的层板reinforcement 加强，加固，加强件，加强部分spar varnish 清光漆waterproof protective material 防水保护材料deterioration 变质，恶化，损坏penetration 尽头，穿透moisture 湿气，潮气，水气protective coating 保护涂层hangar 机库，把-----放入机库中evidence 证据，迹象，形迹rot 腐烂，腐朽fungus 霉菌，真菌wood cell 木材组织，木材微孔cone 圆锥，锥体，锥状物conical shape 圆锥形状cylindrical shape 圆柱形dope 航空用漆，涂布油fiberglass 玻璃纤维stinger 尾不整流锥turbulence 紊流airflow 气流streamlined nose 流线型机头fail-safe feature 破损安全特性tail section 尾部，尾段，尾舱titanium 钛rip-stop doubler 止裂加强板beaded doubler 串珠加强板window belt 窗口地带panel 壁板，地板，板材，仪表板，操纵台，面板，翼段various stage 不同阶段semiautomatic riveting machine 半自动铆接机器shaved riveting 平面铆接dlampong aetion 夹紧力，夹紧作用pounds per square inch (psi) 磅平方英寸kilo-pascals (kpa) 千帕斯卡uniform fastening 均匀一致的连接，均匀一致的紧固件countersunk cavity 埋头窝sealing quality 密封性fatigue life 疲劳寿命longitudinal stiffener 纵向加强件flattened hat section 扁帽型截面stress level 应力水平gauge 规格，尺寸，测量器，量规，卡规，铆钉行距pressure-cabin section 压力舱部分upside-down position 倒置位置dolly 平台车，铆钉顶铁，抵座，圆形锻磨fixture 夹具，卡具，定位装置，安装用具，型架，紧固extruded z transverse frame 挤压成型Z型截面的横向构件mating jig 装配架，总装型架cockpit enclosure 驾驶舱盖subassembly 分装件，部件，局部装配件fuselage shell 机身外壳channel frame 槽型截面构件floor 地板，底面seat track 座椅滑轨carpet 毡层，地毯，铺设地毯expansion beam 伸缩梁flight compartment 机组舱，空勤组舱attachment 廉洁，固定，接头stud bolt 桩螺栓passenger compartment 客舱nut strip 螺帽导板splice plate 拼接板spacer 间隔片，隔离物，垫片，垫圈insulation 绝缘，隔离__aisle panel 通道板freight v. 货物，货运，装货facilities v. 设备，装置，工厂，实验室fabrication 制造，装配，生产individual panel section 单独的壁板区段railroad car 有轨电车handing 处理，加工，操纵，管理，装卸，搬运，吊运handle v. 收兵，把手，处理suction-cup principle 空吸杯装置overhead monorail system 高架单轨吊车系统manufacturing cycle 生产周期sheet-metal holder 钣金夹持器arrangement 排列，布置，安装，构造，布局station number 站位编号distance 距离zero reference point 零参考点floor beam 地板梁keel beam 龙骨梁，底部大梁stretch-formed skin panel 拉伸成型蒙皮板stressed skin 承力蒙皮multiple-element contracture 多元件构造torsional unit 整体部件，组合件advancement 进步，前进，改进state-of-the-art 技术发展水平，目前工艺水平，工艺状态cutaway drawing 剖视图intercostal 加强肋，肋间的material 材料process 过程，流程，工序，步骤，工艺规程，工艺技术，制作方法conclusion 结论fatigue crack 疲劳裂纹corrosion 腐蚀cause 原因，理由，起因stress concentration 应力集中surface corrosion 表面腐蚀galvanic corrosion 电化腐蚀pitting corrosion 点状腐蚀，坑蚀intergranular corrosion 晶界腐蚀exfoliation 剥离，剥落stress corrosion 应力腐蚀fretting corrosion 磨损腐蚀，擦伤腐蚀dissimilar metal 不同金属metal bonding 金属粘结seam 接缝，接口，接合面damage 损伤，破坏，故障，事故roller 磙子，滚桶，碾压机chemical cleaning 化学清洁etching process 浸蚀加工，酸洗处理corrosion-inhibiting epoxy-type primer 防腐蚀环氧树脂底层涂料curing 处置，处理，固化处理epoxy adhesive 环氧树脂粘结剂Teflon fluorocarbon resin release cloth 特氟隆碳氟化合物树脂防粘布bleed cloth 透气布vacuum bag 真空袋autoclave 蒸压器adhesive 粘性的，粘合剂thermosetting epoxy resin 热固型环氧树脂ultrasonic inspection equipment 超声波探伤设备void 空学，空洞porosity 集气孔，沙眼，松孔cabin altitude 座舱高度pressure differential 压力差flight station 乘员舱，（机组人员）飞行工作位置cabin pressurization load 座舱增压载荷titanium fail-safe strap 钛金属破损安全带clad alloy 包覆金属entrapment 夹带，截留formation 形成，组成，构成lighter-gauge skin 较薄的机身蒙皮heavy-gauge skin 大规格蒙皮，厚蒙皮shot penning 喷丸强化，喷丸处理main frame 主隔框，承力隔框，中部最大隔框，主机架stopper 止动器，限制器channel 槽型型材，沟槽，______________管道，通道cut out 切口，开口attaching-clip angle 固定卡箍的角材overlapping 重迭，搭接overlapping stringer 搭接桁条center line 中心线transverse beam 横梁wing box 机翼翼盒wheel well 机轮舱，轮舱deck 地板，层舱sulfuric acid anodizing 硫酸阳极化处理organic-coated steel fastener 有机物涂层的钢紧固件polyurethane painting 聚氨酯涂料corrosion-prone area 易于腐蚀的部位filled-sealed adhesive 嵌缝密封粘合剂passenger door 客舱门center elevating coat room 中央升运保护涂层位置galley service center (机上) 厨房服务中心radome compartment 雷达无线整流罩舱avionics compartment 电子设备舱cargo compartment 货舱center wing 中央翼，中翼cargo door 货舱舱门accessory compartment 附件舱waste tank compartment 废液容器舱fuel vent collection box 燃油通气集油盒（进入同期管道的油在此集中再抽回油箱）rueling interconnect line 加油互连通管道fuel tank 燃油油箱escape chute 应急离机口，应急离机滑梯，应急脱离滑道pressure fueling/defueling couplings 压力加油/放油接头hydraulic service center 液压服务中心galley lift （机上）厨房升降梯air conditioning duct 空气调节系统管道，空调管first class seating 头等舱座椅lavatory 卫生间，盥洗室weather radar 气候雷达curved windowshield panel 弯曲成型的挡风玻璃Rolls Royce RB211 turbofan 罗—罗，RB211涡轮风扇geared elevator 随动升降舵（可操纵水平安定面的）flying stabilizer 可操纵安定面auxiliary power unit (APU) 辅助动力装置pressure dome 球形气密隔框electronic service center 电子设备服务中心after hold (bulk cargo) 后货舱（散装货物，笨重货物）coach class seating 二等舱座位conteinerised cargo 集装箱货物double slotted flap 双开缝襟翼inner aileron 内副翼outer aileron 外副翼full span slat 全展长缝翼inward retraction main wheel 向内收起的主机轮forward retraction nose wheel 向前收起的前机轮air conditioning bay 空调设备舱scale 规模，比例，标尺fin 鳍，垂直安定面，垂直尾翼，立尾elevator 升降舵empennage 尾翼appearance 外形，外貌，外表，外观，出现，出版，发表span 翼展，跨距，间距auxiliary spar 辅助梁hinge v. 铰链，合页，铰接接头installation 装置，设备，安装，装配dorsal fin 背鳍streamlined fairing 流线型整流罩swept-back vertical stabilizer 后掠式垂直安定面stabilator 全动式水平尾翼primary controls 主操纵系统secondary controls 辅助操纵系统aileron assembly 副翼装配件repair 修理maintenance 维护，维修technician 技术人员，技师，专门人员proof of strength 强度验证，强度试验limit load test 最大使用载荷试验，限制载荷试验horn 角状物，操纵摇臂rigging load 校装载荷，水平调整载荷，装配载荷rational manner 合理的方式conservation manner 保守的方式movable tail surface 可动的尾部翼面adjustable stabilizer 可调节的安定面（安定面的安装角，可以改变）ultimate bearing strength 极限挤压强度mass balance 质量平衡concentrated mass balance weight 集中的质量平衡重量control system operation 操纵系统的工作function 功能，职能，作用confusion 混淆，干扰，混乱primary flight controls 飞行主操纵系统pitch 抚养，绕横轴的运动，桨叶角，桨距，紧固件的间距yaw v. 偏航运动，偏航two-control airplane 双操纵面飞机lateral control 横侧操纵directional control 方向操纵stop v. 停止，制动，止动器，止动块，止动装置wear v. 磨损slackness 松弛度take-up adjustment 拉紧调整trim system 配平系统precaution vt. 预防措施，小心，注意，警惕pilot 驾驶员trim device 配平装置irreversible tab 不可逆调整片reliability 可靠性unmistakable warning 清除无误的警告，明显的警告control system lock 操纵系统锁light twin airplane 轻型双发动机飞机jackscrew attachment point 螺旋千斤顶安装点hinge point 铰接点elevator balance panel bay 升降舵平衡翼板隔间flash beacon 闪光灯标attach bracket 固定支架primary flight control surface 飞行主操纵面cruising operation 巡航操作fabric 织物，织品，布，纤维织品water-proof 放水，不漏水，不透水coating 涂层drain hole 放油孔，排水孔，泄漏孔hinge line 铰链轴线auxiliary control surface 辅助操纵面doubler 加强板balance weight 平衡重量access door 检查口盖，工作窗，舱门access panel 口盖，舱盖honeycomb 蜂窝结构vertical axis 立轴flutter 颤振aerodynamic surface 气动力面bracket 支架，托架hinge bracket 铰链支架，铰链架displacement 位移，偏转，偏度aerodynamic efficiency 空气动力效率，气动效率，升阻比control tab 操纵屏，随动补偿片static balance 静态平衡aerodynamic balance 气动平衡，气动补偿dynamic balance 动平衡，飞行中立或力矩的平衡ruddervator V型尾翼，方向升降舵secondary flight control surface 飞行辅助操纵面straight and level flight 直线水平飞行servo tab 伺服片，随动补偿片，操纵片control wheel 驾驶盘，操纵轮crank 祛病，手柄，摇臂cable system 钢索系统actuating device 致动装置screwjack 螺旋千斤顶，螺旋致动器logical manner 合理的方式top rim 顶部轮缘，顶部轮圈position indicator 位置指示器push-pull rod 推拉杆，传动杆set-back hinge line 后置铰链轴线track fitting 滑轨接头leading edge slat 前缘缝翼scalloped doubler 扇形式样加强板fiberglass trailing edge 玻璃纤维后缘beaded-doubler inner skin 串珠状加强板内蒙皮feedback fitting 反馈接合actuation 致动器damper 阻尼器，缓冲器，减震器hinge pin 铰链销cotter pin 开口销，开尾销bearing 轴承control arm 操纵臂，操纵杆balance-weight arm 平衡重量支撑臂detachable elevator 可拆卸的升降舵，可分开的升降舵copilot 副驾驶员headroom 净空（高度），头上空间visibility 能见度，视野clearance 间隙，间距，惊恐，余地，清理，排除parachute 降落伞provision 准备，预备，设备，装置aerobatics 特技飞行，航空表演demonstration 论证，说明，显示，示范flight test 飞行试验flying ability 飞行技能，飞行员驾驶技术egress 出口，出路，外溢personnel 全体人员，全体职员navigator 导航设备，导航仪，领航员flight engineer 随机工程师，空勤机械师appurtenance (常用复数) 附属设备，附件，配件，辅助工具safety vt. 安全性，安全措施，安全，保险assurance 确信，把握，信心，保证concentration 集中，浓缩，聚集propeller-driven airplane 螺旋桨飞机blade 叶片，桨叶air-transportation service 空运服务seal 蜜蜂，封严，密封装置，密封垫，密封胶windshield 风挡，风挡玻璃single-place airplane 单座飞机accommodation 调节机能，适应____________(w，供应，膳宿供应，座位，铺位agriculture aircraft 农业用机instrument 仪表，仪器furnishing 装备，装置，设备，供给dual controls 双重操纵机构first pilot 正驾驶，机长second pilot 副驾驶statement 叙述，陈述，论点up-to-date information 最新的资料ventilation 通风，排起，换气vision 观测，目击，观测，视线，视力windshield wiper 雨刷，风挡刷storm window 风雨窗，双层窗airstream 气流glare v. 闪光，强烈刺目的光reflection 反射，折射，偏射windshield panel 风挡窗格玻璃，窗格玻璃impact 碰撞，冲击，撞击flight path 飞行轨迹，航迹velocity 速度transparent plastic sheet 透明塑料板flanged doubler 弯边的加强板，带凸缘的加强板retaining strip 固定带waterproof adhesive tape 防水胶布带vinyl channel 乙烯塑料槽型件thickness 厚度stiffness 刚度，刚性，安定性，稳定性contour 轮廓线，外形cowl deck 整流罩平台felt seal 毛毡密封indentation 压痕，凹槽manufacturer 制造厂，生产厂家maintenance manual 维修手册laminated panel 层板forged frame 锻制框架，锻造框架hnoist provision 起重设备gasket seal 垫片密封，填料密封removal 拆卸vinyl interlayer 乙烯塑料中间层phenolic spacer 酚醛垫片，酚醛间隔物phenolic block 酚醛块gasket silicone seal 硅铜填料密封剂semi-tempered glass 半强化玻璃terminal 终端，终止，接线柱，引线接头autopilot engage 自动驾驶仪接通navigation marker light 航行标示灯，导航信标接收机信号灯airspeed indicator 空速指示器，空速表pilot directional indicator 自动驾驶仪航向指示器gyro horizon 陀螺地平议，航空地平议compass card 罗盘刻度盘altimeter 高度表，高度计rate of climb 爬升率emergency pneumatic brake 应急气动刹车，应急冷气刹车autopilot axis indicator 自动驾驶仪接通指示器ice-detector light 积冰探测灯engine pressure ratio 发动机压力比，发动机增压比engine r.p.m 发动机每分钟转速thrust-reverser operating light 反推力工作指示灯tailpipe temperature 排气温度管，涡轮后温度master warning 主警告gear down, lock light 起落架放下，锁定信号灯fuel flow 燃油流量tachometer 马赫数表，M数表navigation radio selection 导航无线电选择仪glide slope light 下坡滑度指示灯autopilot disengage 自动驾驶仪切断radio and radar control 无线电和雷达控制air-brake handle 气动刹车减速手柄，减速扳手柄weather radar scope 气象雷达显示器thrust lever 推力杆，油门杆parking-brake letch 停机刹车锁engine start lever 发动机启动手柄turn and bank indicator 转弯侧滑仪hydraulic system pressure 液压系统压力stabilizer trim wheel 安定面配平手轮rudder trim 方向舵配平door post 门框aluminum extrusion 铝挤压件outer retainer 外部固定件，外部保持件temperature sensing element 热敏元件five-ply laminated panel 五层层压窗格玻璃insert 垫圈，插入物defog bus bar 清除混蚀汇流条，扫雾汇流条conductive coating 导电敷层chip retarder 碎裂阻聚剂anti-ice bus bar 防冰汇流条air carrier 航空运输公司，空运工具，运输机presence 存在fuel fume 燃油蒸汽，燃油雾气carbon mobixide 一氧化碳dangerous trace 危险的痕迹ventilation system 通风系统heating system 加温系统pressurization system 增压系统first-class section 一等客舱段trijetliner 三发喷气式航线客机airline 航线，航空公司coach section 二等舱客段broad lofty ceiling 宽阔高耸的舱顶spaciousness 宽敞，宽敞度aisle 通道，走廊divider 分配器，分隔器personal effects 个人财物carry-on luggage 随身的行李safety-belt 安全带，保险带cycle pressurization loading 循环增压载荷pressurized airliner 座舱增压式航线客机cabin sidewall lining 座舱侧壁材料fail-safe structure 破损安全结构acrylic plastic 聚丙烯塑料peripheral seal 周边密封，周缘密封sponge rubber 泡沫橡胶，多孔橡胶spring retainer 弹簧座圈shouldered screw 带托肩的螺钉window-frame forging 窗框锻件reveal 窗框半槽边，窗侧retaining bracket 固定架window ring pan 环形窗框clip 夹子，卡箍slit 长缝，裂缝conditioned air 以调节空气condensation 凝聚，凝结acoustical seal 吸音密封window shade 窗户遮光罩，窗帘acoustical pane 吸音窗玻璃side wall panel 侧壁板formed sheet-metal structure 预成型钣金结构hydro press 水压机stamp press 冲压机，模锻压力机drop hammer 落锤entrance 进口upholstered cabin 装饰过的座舱matching upholstered panel 匹装备饰板door latching 门扣locking mechanism 锁机构forward entry door 前登机门hinge gate 铰接活门door opening 舱门口hinging mechanism 铰接机构，门枢机构controlling mechanism 操纵机构，控制机构plug 塞子，孔塞，堵塞物securing mechanism 关紧机构inside handle 内部手柄cam plate 凸轮盘，凸轮板latching-crank assembly 柄锁装配件angular movement 角运动latch rod 锁杆latch roller 锁滚柱cock-crank assembly 竖起的曲柄装配件torque-tube crank 扭转曲柄hinge arm 铰接臂guide arm 导向支臂snubber 缓冲器，消音器assist handle 辅助手柄radius link 摇柄pivot axis 止动销stop pin 止动板latch pin 锁销door-open stowing latch lever 舱门打开收锁杆remainder 剩余部分recessed handle 隐藏式手柄，隐藏在凹坑处的手柄complexity 错综复杂，复杂的事物bogy 小车，转向架normal mode 普通型emergency mode 应急型auxiliary mode 辅助型emergency evacuation slide 应急排空滑块deployment 部署，展开，散开，开伞reveal seal 窗侧密封outer pane spring assembly 外部窗格玻璃弹簧装配件permanently mounted screw 永久性固定螺钉nutplate 托板螺帽ventilation hole 通气孔ventilation slot 通气缝window trim 窗狂细木工件，窗框装饰trim pad 细木窗框衬垫escutcheon plate 锁眼盖，孔罩板handle mechanism housing 手柄机构外壳avionics compartment lower door 电子设备下舱门avionics compartment aft door 电子设备后舱门air conditioning compartment door 空调舱门forward passenger door 前客舱门center accessory compartment door 中央辅助设备舱门overawing passenger door 机翼上方客舱门center cargo door 中央货舱门APU compartment door 辅助电源设备舱舱门tail cone lower door 尾锥下舱门overstress 过大应力，过载，超载overstressing 过应力，超限应力landing load 地面载荷（指起飞，着陆或在地面滑行时，飞机结构承受的载荷）fixed landing gear 固定式起落架retractable landing gear 收放式起落架conventional arrangement 常规配置，正常配置tricycle arrangement 前三点布局，前三点配置tricycle landing gear arrangement 前三点式起落架布局nose wheel 前轮old conventional gear 旧式常规起落架tail-wheel type 尾轮式main gear 主起落架strut 支柱，撑杆，吊架body-gear strut 机身起落架支柱wing-gear strut 机翼起落架支柱nose-gear wheel 前起落架机轮main wheel 主轮axis 轮轴，车轮main beam 主梁caster 脚轮，转向轮swivel 旋转接头，旋转节，旋转shock-absorbing method 减震方法rubber shock cord 橡皮减震绳，缓冲绳rubber disk 橡皮盘coil spring 螺旋弹簧，盘簧hydraulic piston 液压活塞flexible spring steel 柔性弹簧钢oleo 油液减震器，油液减震支柱air-oleo 空气—油液减震器spring-oleo 弹簧—油液减震器flexibility 柔性，韧性，挠性elasticity 弹性alloy steel 合金钢brake 刹车air-oleo strut 油气式减震支柱cylinder 气缸，做动筒，圆筒metering piston 分油活塞，分油柱塞orifice 小孔metering pin 调节油针taxi 滑行cross-sectional drawing 剖视图retracting system 收起系统trunnion 轴颈，枢轴，耳轴retracting mechanism 收起机构electric operated screw 电操纵螺杆hydraulic actuating cylinder 液压致动作动筒civil airplane 民用飞机，民航飞机linking device 连接机构drop-test 着陆重量（起落架）落震试验，冲击试验wheel well door 起落架舱门，轮舱盖supporting structure 支撑结构friction 摩擦力inertia 惯性brake torque 刹车扭矩air load 气动载荷retraction 收回extension 伸出，延伸stalling speed 失速速度approach position 进场着陆位置cruising speed 巡航速度load factor 载荷因数，过载，装载系数（有效载荷与飞机起飞重量比）yawing maneuver 偏航运动，方向动机positive means 可靠的方法safety switch 安全电门，保险开关emergency system 应急系统emergency means 应急方法operational test 使用实验，工作实验retracted position 收上位extended position 放下位landplane 陆上飞机aural warning device 声响报警装置，声响报警器throttle 节流阀，节流油门，节气门manual shutoff 手动关断landing-gear control knob 起落架控制按钮transport-airplane 运输机tire 轮胎，轮箍multiple landing gear 多轮起落架compressed air chamber 压缩空气室piston tube 活塞管inner cylinder 内筒outer cylinder 外筒oil chamber 油室power plant 动力装置，发动机mount 支架座，安装，固定，装配enclosed shelter 封闭的掩蔽所multiengine airplane 多引擎飞机National Aeronautics and Space Administration (NSAS) 国家航空和宇航局stream-lined structure 流线型结构pod 吊舱，短舱，分离舱，可拆卸的货舱pylon 外挂梁，吊架，挂架，支架engine mount 发动机架formed sheet metal 冷弯钣金件welded steel tube 焊接钢管forged steel 锻制钢reciprocating (position) engine 活塞式发动机overhaul 大修engine change 发动机更换liquid line 液体管路electric cable 电缆control linkage 操纵线系quick-disconnect joint 快速拆卸接头quick engine change (QEC) 快速更换发动机package 组件，部件，成套设备radial engine 星型发动机opposed engine 对置式发动机bushing 衬套，衬筒vibration absorption 震动吸收pad 沉淀，填料，垫片，底座台cushion 垫子，软点，减震垫restraining action 约束作用manufa cturer’s handbook 制造厂手册mount bracket 固定托架，安装托架dynamic suspension 非刚性支撑法，减______________震悬。
飞机维修部件中英对照学习
飞机维修部件中英对照学习12飞机维修部件中英对照学习单向活门 Check Valve快速热水器 Rapid Water Heater安全活门 Safety valve高压级调节活门 High stage pilot高压级引气活门 High stage regulator引气调节器 Bleed air regulator反流检查控制活门 Reverse Flow Control Valve过滤型压差调节器 Filter type differential pressure regulator 四英寸直径气动蝶形关断活门Four inch diameter pneumatic butterfly shutoff valve马桶组件 Toilet assembly冲洗活门组件 Flush Valve Assy圆顶灯 Dome Light真空马桶组件 Vacuum toilet assemblies活门组件 Valve Assy冲水马桶组件 Flushing toilet assembly排水活门组件 Holders of drain valve assembly控制显示组件 Control/Display Unit飞行管理计算机 Flight Management Computer防冰活门 Nose cowl thermal anti-ice valve液晶控制显示组件 Liquid Crystal DisplayControl/Display Unit 热交换器 Heat exchanger初级热交换器 Primary heat exchanger货舱动力驱动组件 Cargo Powered Drive Unit发动机仪表系统次显示板 E.I.S secondary display panel58加仑真空污水箱 58 Gallon vaccum waste tanks50A 不可调变压整流器Transformer-Rectifier,50 AMP Unregulated直流转接盒 DC Junction Box风档温度控制器 Windshield Temperature Controller窗户和空速管加热模件组件P5-9 Window and Pitot Heat Module Assembly,P5-9燃油控制模件组件P5-2 Fule control module assy.p5-2电源管理控制模件组件P5-68 Power management control module assy.交流系统发电机/APU模件组件P5-4 AC System Generator/APU ModuleP5-4 Assembly发电机驱动和备用电源模件组件P5-5 Generator Drive and Standby Power Module Assembly,P5-5发电机驱动和备用电源模件组件P5-6 Generator Drive and Standby Power Module Assembly,P5-6发电机驱动和备用电源模件组件P5-7 Generator Drive and Standby Power Module Assembly,P5-7飞行记录和马赫空速警告模件组件P5-19 Flight Recorder and Mach Airspeed Warning Module Assyembly,P5-19飞行控制模件组件P5-3 Flignt Control Module Assembly P5-3 烤箱 Oven俯仰计算机 Pitch Computer变压整流组件 Transformer Rectifier Unit发动机附加组件 Engine Accessory Unit Assembly仪表着陆控制板组件 ILS Control Panel Assy.特高频全向导航控制板组件 VOR Control Panel Assy.机翼位置航行灯 Wing Position Navigation Light飞机航行防撞频闪灯Aircraft Navigational，'Anti-collision Strobe Light高亮度飞机识别灯 High Intensity Aircraft Recognition Light飞机尾翼闪光灯 Aircraft Tail Position Light，Flashtube飞机后位置航行灯 Aircraft Navigational Light-rear position后位置灯组件 Rear Position Light Assembly上机身防撞灯 Upper Fuselage Anti-Collision Light下机身防撞灯 Lower Fuselage Anti-Collision Light发动机仪表系统主显示板 E.I.S Primary Display Panel马达泵过滤器组件 Motor-pump-filter unit assembly压力调节活门 Pneumatic Pressure Regulating Valve压力调节和关断活门 Pressure regulating and shutoff valve高压级引气调节器 High stage valve双效用活门 Dual purpose valve机头罩防冰活门 Nose Cowl Anti-lce Valve预冷器冷却空气调节活门 Four inch diameter precooler control valve预冷器冷却空气调节门 Modulating pre-cooler air valve第十四级调节活门 Fourteenth-stage pilot驾驶舱灯 Cockpit Light压差调节器 One and One-half inch diameter turbofan control shutoff differential pressure regulator流量活门 Flow control valve5英寸直径流量控制活门 Five inch diameter flow control valve 流量控制和关断活门 Flow control and shuttoff valve3 1/2英寸直径流量控制活门 Three and one half inch diamter flow control valve3 1/2英寸直径电动控制双向调节和关断蝶形活门 Three and one half inch diamter flow control valve electric dual modulating and shutoff butterfly valve电瓶充电器 Battery Charger偏航阻尼耦合器 Yaw Damper Coupler大气数据计算机 Air Data Computer天花板灯 Ceiling Light飞行控制计算机 Flight Control Computer方式控制板 Mode Control Panel行李箱扭矩臂组件 Center Overhead Stowage Bin Upper Arm Torque Tube Assembly防滞/自动刹车控制组件 AntiSkid/Autobrake Control Unit防滞刹车控制组件 Skid Control Unit刹车系统控制组件 Brake System Control Unit着陆灯 Landing Light收放着陆灯 Retractable Landing Light回收箱挡块组件 Retractable Container Stop Assembly发动机火警,过热,'APU火警控制模件Control Module,Engine Fire,Overheat & APU Fire翼尖航行灯 Wing Tip Navigation Light频闪灯电源 Strobe Power Supply水壶 Water Boiler组件/区域温度控制器 Pack/Zone Temperture Controller客仓区域温度控制器 Cabin Zone Temperature Controller组件温度控制器 Pack Temperature Controller马达驱动风扇 Motor Driven Fan座舱空气循环风扇 Cabin air recirculation fan信号灯组件 Indicator Light AssemblyAPU 控制组件M820 APU Control Aassembly M280APU 控制组件 APU Control Unit Assembly空调辅助组件M324 Air Conditioning Accessory Unit Assembly M324综合飞行系统辅助组件Integrated Fight System Accessory UMA轴流式风扇组件 Vaneaxial Fan Assembly发动机振动监控器 Engine Vibraction Monitor马达操纵关断活门 Motor Operated Air Shutoff Valve发动机和APU火警控制模件组件P8-1 Engine and APU Fire Control Module Assembly P8-1液压泵模件组件P5-8 Hydraulic Pumps Module Assembly P5-8空调模件组件 Air Conditioning Module Assembly发动机及机翼防冰模件组件P5-11 Engine and Wing Anti-ice Module Assembly.P5-11客舱温度模件组件P5-17 Cabin Temperature Module AssemblyP5-17燃油系统模件组件P5-2 Fuel System Module Assembly P5-2 窗户及全-静压空速管加热模件P5-9 Window and Combind Pitot-Static Heat Module Assembly P5-9窗户及全-静压空速管加热模件Window and Combind Pitot-Static Heat Module Assembly P5-9IRS 方式选择模件组件 IRS Mode Selector Module Assembly 压力控制板 Pressure Control Panel快速烤箱DF700LH High Speed Oven DF 700LH蒸汽烤箱 Steam Oven高速烤箱 High Speed OvenDR4100系列热水器 Water Heater DR4100 Series活门 High Stage Bleed Valve汇流条电源控制组件 Bus Power Control Unit流量控制活门 Flow Control Valve自动油门计算机 Autothrottle Computer压力控制器 Pressure Controller流量和关断活门 Flow control and shutoff valve高压控制器 High Pressure Controller真空抽气马桶 Vacuum toilet assembly滑油箱 Lubricating oil tank接近电门电子组件 Proximity Switch Electronics Unit高压关断活门 High Pressure Shutoff Valve咖啡壶组件 Coffeemaker Assembly蒸气烤箱 Steam Oven风档加温控制器 Window Heat Controller凤挡加热控制组件 Window Heat Control Unit烤箱组件 Oven Aseemblies发动机超温火警探测器Engine Overheat and Fire Detection Unit麦克风 Micophone发电机控制组件 Generator Control Unit汇流条保护板 Bus Protection Panel风扇活门 Fan Air Valve高压流量控制活门 High Pressure Bleed Control Valve清水箱 Potable Water Tank数字/模拟转接器 Digital/Analog Adapter串行摆动飞机航行灯 Tandem Oscillating Aircraft Navigational Light数字式大气数据计算机 Digital Air Data Computer马桶真空泵 Vacuum Generator飞机头戴式耳机 Aircraft Headsets自动关闭水开关组件 Fancet Assy-self close放音机 Wall Mount Type Prerecorded固态壁挂式预录通告和登机音乐磁带放音机 SOLID-STATE WALL MOUNT PRAM。
高大上的飞机维修工具大汇总
常用飞机维修工具大汇总——中英文对照版2.十字螺丝刀———Philipshead Screwdriver3.螺母螺刀———Nut Screwdriver6.仪表螺刀——Electronic miniature Screwdrivers7.弯头十字/一字螺刀——Offset Screwdrivers9.剪钳—— Diagonal Cutters10.保险钳——Wire Twister（PS ：超爱这把小钳子，打出来的保险均匀紧致，实在是强迫症机务的最大福音！！）11.鹰嘴钳——Adjustable Joint / Alligator Pliers12.插头钳——Connector Pliers(如果插头拧不动，又不能用蛮力的时候，就该它上场啦~~温和保护，轻轻一拧，插头就下来啦)13.尖嘴钳——Needle Nose Pliers14.鸭嘴钳——Duck Bill Pliers15.剪线钳——Bolt Cutters/ Pliers16.大力钳——Locking Pliers, Vise-Grip(当拆的家伙实在顽固，我们只能召唤大力水手啦~~看你得瑟~~哼哼~~不过大力钳会产生一定的伤害哦~）17.锁定夹——Locking Clamp18.C型夹——C-Clamps19.卡环钳——Retaining Ring Pliers卡环有内卡环和外卡环，所以，卡环钳也有内卡环钳和外卡环钳20.剥线钳——Wire Crimper/ Stripper/ Cutter21.焊枪、烙铁——Soldering Gun/ Iron22.开口扳手——Open end Wrench23.弯头梅花扳手——Box Wrench24.开口梅花扳手——Combination Open-Box Wrench25.S型梅花扳手——…S‟ Shaped Box Wrench26.半月型组合扳手——Half Moon Box Wrench 27.片卡拉——RatchetingBox Wrench28.套筒扳——Socket Wrench29.活动板——AdjustableWrench/Single Open Ended Spanner30.套装内六角——Hex (Allen Keys) Wrench31.L型内六角——Hex L Shaped (Allen Keys) Wrench,32.片开口——Crowfoot Open End Wrench33.梅花片开口——Crowfoot Flare Nut Wrench34.链条扳——Chain Wrench35.皮带扳——Strap Wrench 36.管子扳——Pipe Wrench37.管子扳（活钩扳手）——Adjustable Hook Spanner Wrench大家看它的英文名儿里的Hook，是不是想起来“小飞侠彼得潘”里的Hook船长，他的手就是个钩子嘛~~额。
飞机维修中各类工具中英文对照
飞机维修中各类工具中英文对照扳手Wrenches/套筒Sockets开口扳手 Open End Wrenches梅花扳手 Spline End Wrenches块扳手 Crowfoot Wrenches开口/梅花扳手 Combination Wrenches内六角扳手 Hex Wrenches平板棘轮扳手 Slab Ratchet棘轮扳手 Ratchet Wrenches力矩扳手 Torque Wrenches管钳 Pipe Wrenches活动扳手 Adjustable Wrenches六角套筒 Six Point Sockets梅花套筒 Twelve Point Sockets万向套筒 Universal Sockets转接头 Adaptor套筒接杆 Socket Extension万向转接头 Universal Joint螺刀Screwdrivers快速螺刀 Fast Screwdrivers仪表螺刀 Electronic miniature Screwdrivers 十字头螺刀 PILLIPS Screwdrivers磁性螺刀 Magnetic Screwdrivers一字头螺刀 Flat Tip Screwdrivers摇把 Speeders钳Pliers尖嘴钳 Needle Nose Pliers大力钳 Locking Pliers保险丝钳 Safety Wire Twisters鹰嘴钳 Adjustable Joint Pliers插头钳 Connector Plug剥线钳 Wire Strippers鱼口钳 Combination Slip-Joint Pliers PliersRing Snap Convertible 卡环钳Diagonal Cutters 剪线钳CrimpersWire 压线钳ToolsElectronic 电气工具(Miner's Lamb) Safety 矿灯 LambLight Flashing 手电Interphone 对讲机Iron Electronic 电烙铁Earphone 耳机Wrist Static 防静电手腕电池 Battery充电器 Charger扬声器 Speaker电源插座 Receptacle电枪 Electronic Runner电钻 Electronic Drills指挥棒 Flashing Emergency Light超声波 Ultrasonic测量工具Measuring Tools钢板尺 Steel Rulers卷尺 Tape Rulers螺旋卡尺 Outside Micrometer塞尺 Feeler (Thickness) Gauges量杯 Measuring Cup游标卡尺 Dial Caliper表 Gauges三用表 Multi Meter兆欧表 Meg Ohm MeterDiversiform杂项Inspection Mirror 反光镜Magnifier 放大镜软杆双爪式机械 Pick Up Tool 手 Flexible Two_claw ToolPick Up 软杆磁棒 Flexible MagneticUtility Knife 划刀Knife Scraper 刮刀Snip (Scissor) 剪刀Saw 锯Chisels 凿子Punch 錾子Tripod 三脚架 (Spider)Hammer Copper 铜榔头铁榔头 Iron HammerHammerRubber 胶榔头Hook 弯勾File锉(Pliers) Nipper 镊子Tools Pin Removal 销钉插拔工具气枪 Pneumatic RunnerDrillsPneumatic 气钻Rivet Gun 铆钉枪(Squirt) Injector 注射器滑油加油车 Oil CartCartHydraulic Fluid 液压油加油车注油枪 Gun Grease抹布 Dishcloth手套 Glove绳索 Rope工具箱 Tools Kit工具架 Tools Rack千斤顶 Jack撬棒 Tommy Bar工作梯 Work Ladder砂轮 Grinding wheel砂纸 Sand paper胶带 Adhesive Tape焊锡 Soldering Tin拖把 Tow Bar发光背心 Flashing Vest护目镜 Goggle (Blinkers)安全带 Life Belt(Safety Belt)增补两用扳手CONBINATION SPANNER两用扳手套装COMBINATION SPANNER SET加长型两用扳手COMBINATION SPANNER EXTRA LONG梅花棘轮开口扳手OPEN ENDED SPANNER WITH RING RATCHET梅花棘轮开口扳手套装OPEN ENDED SPANNER WITH RING RATCHET SET 两用棘轮扳手COMBINATION RATCHET SPANNER两用棘轮扳手套装COMBINATION RATCHET SPANNER SET1/4'连接物ADAPTOR 1/4'组合支架工具COMBINATION HOLDING TOOL小型发光二极管MINIATURE LED LAMP活动扳手SINGLE OPEN ENDED SPANNER扳手套装MAGNETO SPANNER SET单开口扳手/呆扳手SINGLE ENDED OPEN JAW SPANNER双开口扳手DOUBLE OPEN ENDED SPANNER双开口扳手套装DOUBLE OPEN ENDED SPANNER SET扩口螺母扳手PLARE NUT SPANNER（OPEN）半月型梅花扳手HALF-MOON RING SPANNER双头梅花扳手（短）DOUBLE ENDED SPANNER（SHORT）双头梅花扳手（长）DOUBLE ENDED SPANNER（LONG）平头梅花扳手（直）FLAT RING SPANNER STRAIGHT PATTERN开口敲击扳手OPEN ENDED SLOGGING SPANNER梅花敲击扳手RING SLOGGING SPANNER高颈梅花敲击扳手DEEP AFFSET RING SLOGGING SPANNER直头梅花扳手DEEP RING SPANNER（STRAIGHT PATTERN）延长管EXTENSION TUBE爪型扳手CROWFOOT SPANNER两用活头扳手COMBINATION SWIVEL HEAD WRENCH活结T型扳手SWIVEL HANDLE WITH SLIDING T套筒扳手SOCKET WRENCH弯头套筒扳手ANGLED SOCKET WRENCH双头套筒扳手DOUBLE ENDED SOCKET WRENCH旋棒TOMMY BAR分节旋棒STEPPED TOMMY BAR3C把手套筒扳手SOCKET WRENCH WITH 3C-HANDLET型及磁性套筒扳手SOCKET WRENCH WITH T-HANDLE AND MAGNET 钩头扳手HOCK SPANNER WITH LUG带销扳手PIN SPANNER可调式两爪钩扳手CALIPER FACE SPANNER WITH ADJUSTABLE1/4'标准六角套筒HEXAGON SOCKET1/4'加长六角套筒HEXAGON LONG PATTERN SOCKET棘轮扳手RATCHETS套筒SOCKETS套筒套装SOCKETS SETS摩擦棘轮扳手FRICTION RATCHETS冲击工具IMPACT TOOLS旋具头BITS扭矩扳手TORQUE WRENCHES1/4梅花套筒SOCKET UD PROFILE1/4六角套筒星型套筒SOCKET FOR PROTRUDING HEAD SCREWS1/4一字，十字，星型，内六角旋具套筒1/4'双向棘轮套筒扳手1/4'REVERSIBLE RATCHETT柄棘轮扳手RATCHET WITH T-HANDLE手用棘轮头HAND RATCHET WITHOUT HANDLE1/4转3/8转换接头CONVERTER 1/4 TO 3/8T型滑动头手柄TOMMY BAR WITH SLIDING T活动延长杆FLEXIBLE EXTENSION通用延长杆UNIVERSAL-JOINT EXTENSION1/4四方驱动连接头SQUARE-DRIVE COUPLER1/4万向接头UNIVERSAL JOINT活动头手柄SWIVEL HANDLE套筒固定夹SOCKET RAIL WITH MAGNETIC3/8一字，十字，星型，内六角旋具套筒3/8六角套筒SOCKET HEXAGON 3/83/8梅花套筒SOCKET UD PROFILE塑料棘轮扳手PLASTIC RATCHET旋具头接头BIT ADAPTOR旋具头棘轮扳手BIT RATCHET旋具头螺丝起子BIT SCREWDRIVER旋具头延长杆BIT EXTENSION旋具头SCREWDRIVER BITS风动套筒IMPACT SOCKET风动套筒附件ACCESSORIES FOR IMPACT SOCKET手动操作冲击手柄HAND-OPERATED INPACT DRIVER摩擦式梅花棘轮扳手FRICTION TYPE RATCHET WITH RING WITH BI-HEXAGON 摩擦式四方棘轮扳手FRICTION TYPE RATCHET WITH SQUARE RING安装扳手/尖尾扳手CONSTRUCTION RATCHET BI-HEXAGON0.6-5.4NM扭力螺丝起子TORQUE SCREWDRIVER HANDLE 0.6-5.4NM3C一字螺丝起子3C-SCREWDRIVER FOR SLOTTED HEAD SCREWS3C十字PH螺丝起子3C-SCREWDRIVER FOR CRUCIFORM HEAD PH3C米字螺丝起子3C星型螺丝起子3C球头六角螺丝起子5件/6件/7件/155件螺丝起子套装SET FOR HEAD SCREWS电工螺丝旗子ELECTRONIC SCREWDRIVER木柄螺丝起子SCREWDRIVERS WITH WOODEN HANDLE磁化/消磁器MAGNETIZER AND DEMAGNETIZER方刃锥子SQUARE BLADED AWLT型六角螺丝起子HEXAGON SCREWDRIVER WITH T-HANDLET型内六角扳手HEXAGON SOCKET KEY WITH T-HANDLE内六角扳手HEXAGON SOCKET KEY加长内六角扳手EXTRA LONG HEXAGON SOCKET KEY加长球头内六角扳手内六角扳手套装HEXAGON SOCKET KEY SETT型星形螺丝起子SCREWDRIVER WITH T-HANDLE曲柄螺丝起子CRANKED SCREWDRIVER量规GARGE车灯测电笔CAR LIGHT TESTER6-24伏测电笔VOLTAGE TESTER 6-24V150-250伏测电笔VOLTAGE TESTER 150-250V钳子3件套装PLIERS SET，3-PIECE万能手钳48件套UNIVERSAL PLIERS ASSORTMENT WITH 48 PIECE小钢丝钳SMALL COMBINATION PLIERS钢丝钳（德式）COMBINATION PLIERS（GERMAN PATTERN）钢丝钳（欧式）COMBINATION PLIERS（EURO PATTERN）强力钢丝钳POWER COMBINATION PLIERS塑料水口钳SIDE CUTTERS FOR PLACTIC剪钳（瑞典款式）SIDE CUTTERS（SWEDISH PATTERN）电工剪钳ELECTRICIAN'S SIDE CUTTERS剪钳（美国款式）POWER SIDE CUTTERS（AMERICAN PATTERN）杠杆剪钳LEVER-ACTION SIDE CUTTERS杠杆顶剪钳LEVER-ACTION END CUTTING NIPPERS核头钳TOWER PINCERS拨钉钳PINCERS平头钳FLAT NOSE PLIERS圆头钳ROUND NOSE PLIERS直头尖嘴钳LONG NOSE PLIERS弯头尖嘴钳电话钳TELEPHONE PLIERS强力尖嘴钳TRIPLE-FUNCTION PLIERS直口机修工钳MECHANICS PLIERS STRAIGHT PATTERN曲口机修工钳MECHANICS PLIER ANGLED PATTERN偏口机修工钳MECHANICS PLIER OFFSET PATTERN30度平圆机修钳MECHANICS PLIER WITH 30电缆刀CABLE KNIFE电工电缆刀ELECTRICIAN'S CABLE KNIFE防静电专用钳子电子钳ELECTRONIC PLIERS迷你电子钳MINIATURE ELECTRONIC PLIERS防静电尖嘴钳/防静电顶切钳/电子平头钳/电子剪钳/防静电剪钳/电子剥线钳电缆剪钳CABLE CUTTERS小型万用剪SMALL UNIVERSAL SCISSORS万用电缆刀UNIVERSAL CABLE KNIFE自动剥线钳STRIPPING PLIERS ANTOMATIC剥线钳STRIPPING PLIERS固定剥线钳STRIP-FIX STRIPPING PLIERS剥线工具WIRE STRIPPER高效剥线钳HIGH-PERFORMANCE WIRE STRIPPER数据传输电缆精确剥线钳PRECISION WIRE STRIPPER FOR DATA CABLES同轴电缆剥线钳WIRE STRIPPER FOR COAXIAL CABLES绝缘剥漆钳INSULATING VARNISH STRIPPER剥线刀WIRE STRIPPING KNIFE绝缘胶带INSULATING TAPE压线钳CRIMPING PLIERS锁把式压线钳LOCK-GRIP CRIMPING PLIERS端子压线钳WIRE END-SLEEVE PLIERS模块压线夹钳MODULAR LOCK-GRIP CRIMPING PLIERS模块压线钳MODULAR CRIMPING PLIERS精确压线钳PRECISION CRIMPING PLIERS外卡簧钳（轴用）EXTERNAL CIRCLIP PLIERS（ON SHAFTS）直头/弯头外卡簧钳（轴用）内卡簧钳（孔用）INTERNAL CIRCLIP PLIERS（IN BORES）直头/弯头内卡簧钳（孔用）大型/重型卡簧钳X型把X-GRIP大力钳LOCK-GRIP PLIERS平行钳夹大力钳PARALLEL JAW LOCK-GRIP PLIERS宽口大力钳WIDE JAW LOCKING PLIERS滑行杆式大力钳LOCK-GRIP SLIDE CLAMP固定大力钳GRIP WRENCH FOR GLUEING机械工作台钳MACHINE WORKBENCH CLAMP焊接大力钳LOCK-GRIP WELDING CLAMP管子焊接大力钳LOCK-GRIP TUBE WELDING CLAMPC型大力钳LOCK-GRIP C CLAMP水泵钳UNIVERSAL PLIERS（7种设置/5种设置）水泵钳WATER PUMP PLIERS特殊水泵钳SPECIAL WATER PUMP PLIERS可调式高速管子钳HIGH-SPEED PIPE WRENCH WITH SCREW ADJUSTER高速曲口管子钳HIGH-SPEED PIPE WRENCH CURVED迷你链式管子钳MINI CHAIN PIPE WRENCH链钳CHANIN PIPE WRENCH重型管子钳STILLSON PIPE WRENCH断线钳BOLT CUTTERS钳子套装（3件/4件/6件/8件）VDE绝缘安全电工工具VDE INSULATED SAFETY TOOLSVDE绝缘标准符合DIN EN 60900 IEC 60900：2004以及VDE680 适合在高压区安全工作（AC1000V DC1500V）VDE绝缘螺丝起子VDE SCREWDRIVER（一字/十字/米字/星型/内六角）VDE绝缘起子套装电压传感器/电压测试器VOLTAGE DETECTOR/TESTER绝缘扭力扳手VDE TORQUE WRENCH绝缘双向棘轮扳手VDE REVERSIBLE RATCHET绝缘六角套筒VDE SOCKET HEXAGONAL绝缘旋具头套筒VDE SCREWDRIVER BIT SLCKETT型绝缘扳手VDE T-HANDLE绝缘延长杆VDE EXTENSION绝缘电工工具组套（3件/8件/14件/108件）VED 3C绝缘手柄套筒扳手VDE SOCKET WRENCH WITH 3C HANDLE绝缘梅花扳手VDE SINGLE-ENDED RING SPANNER WITH DEEP OFFSET绝缘开口扳手VDE SINGLE-ENDED OPEN SPANNERVDE绝缘钢锯HACKSAW绝缘电缆刀VDE CABLE KNIFE绝缘电缆剪CABLE SHEARS棘轮式绝缘电缆剪钳CABLE CUTTERSVDE绝缘电缆剪VDE CABLE SHEARS绝缘剥线钳/绝缘固定剥线钳/绝缘水泵钳/绝缘强力钢丝钳/绝缘斜口钳/绝缘电工斜口钳/绝缘平口钳/绝缘圆头钳/绝缘直头尖嘴钳/绝缘弯头尖嘴钳VDE绝缘橡胶垫VDE RUBBER COVER SHEETVDE绝缘电工安全手套VDE ELECTRICIANS'S SAFETY GLOVES绝缘塑料夹VDE PLASTIC CLAMPS车轮扳手WHEEL WRENCHES十字扳手4 WAY WHEEL WRENCH撬棒TYRE LEVER轮毂罩移除工具HUBCAP RENOVING TOOS配重钳BALANCE-WEINHT PLIERS制动弹簧钳BRAKE-SPRING PLIERS闸线弹簧钳PLIERS FOR BRAKE-CABLE SPRINGS制动钳刷BRAKE-CALIPER BRUSH放油塞扳手（四方）DRAIN-PLUG WRENCH WITH SQUARE油壶OIL CANS过滤器扳手UNIVERSAL FILTER WRENCH皮带钳PULLEY WRENCH阀门研磨机VALVE GRUNDER阀门研磨工具VALVE LAPPING TOOS油封钳VALVE-SEAL PLIERS GUNMETAL FINISH汽缸/活塞环压缩器VALVE SPRING COMPRESSOR BRIGHT NICKEL-PLATDE 活塞环钳PISTON RING PLIERS软管夹钳HOSE CLIP PLIERS电极拉马BATTERY TERMINAL PULLER电池测试器BATTERY TESTER火花塞套筒SPARK PLUG SOCKET火花塞套筒扳手SPARK PLUG SOCKET WRENCH火花塞刷SPARK-PLUG BRUSH特殊尖冲凿SPECIAL PIN PUNCH弹簧撑开器SPRING SPREADER球头拉拔器UNIVERSAL BALL JOINT REMOVER通用罐UMIVERSAL CANISTER防冻测试器ANTI-FREEZE TESTER安装钳INSTALLATION PLIERS吸盘SUCTION LIFTER磁性拾取工具MAGNETIC PICK-UP TOOL金属片切割器NIBBER杠杆剪切机LEVER-ACTION TIN SNIPS打孔钳PUNCH PLIERS橡胶锤RUBBER HAMMER塑料锤PLASTIC HAMMER无后坐力锤RECOILLESS HAMMER钳工球头锤ENGINEERS'S BALL PEIN HAMMER钳工锤ENGINEERS'S HAMMER平面刮刀FLAT SCRAPER三角空心刮刀THREE-EDGED HOLLOW-GROUND SCRAPER三角实心刮刀THREE-EDGED FLAT-GROUND SCRAPER密封刮刀GASKET SCRAPER平锉HAND FILE圆锉ROUND FILE三角锉TRIANGULAR FILE半圆锉HALF-ROUND FILE锉类6件套装中心冲/凿/开口销冲CENTRE PUNCHES/CHISELS/DRIFT PUNCHES 钢锯HACKSAW栓孔锯KEYHOLE SAW小金属锯SMALL METAL SAW小PUK钢锯PUK JUNIOR HACKSAWHOBBY锯台钳/台虎钳METALWORKING VICE（100/125/150mm）钢卷尺STEEL TAPE MEASURE（3米/5米/8米）阀塞尺VALVE FEELER GAUGE塞尺火花塞塞尺SPARK PLUG GAUGE螺纹规THREAD GAUGE游标卡尺POCKET VERNIER CALLIPER数显游标卡尺DIGITAL CALLIPER划线器SCRIBER镊子TWEEZERS十字镊子CROSSLOCK TWEEZERS螺钉取出器BOLT EXTRACTOR断螺钉取出器套装SCREW EXTRACTOR SET机械螺母破开器MECHANICAL NUT SPLITTER螺栓插入及取出器STUD INSERTER AND EXTRACTOR丝锥THREAD FILE管子割刀PIPE CUTTER自动切割机AUTOMATIC PIPE CUTTER链式切管机CHAIN PIPE CUTTER虹吸扳手SIPHON TRAP PLIERS钢丝刷WIRE BRUSH锉刀清洁刷FILE CLEANING BRUSH裁缝剪TAILORS SCISSORS发光二极管井下检查灯LED INSPECTION LAMP井下检查灯INSPECTION LAMP发光二极管工作灯LED WORK LIGHT工程锤ENGINEERS HAMMER ROTBAND-PLUS工程圆头锤ENGINEERS'BALL PEIN HAMMER胡桃木备用手柄SPARE HANDLE HICKORY工匠锤JOINERS'HAMMER ROTBAND-PLUS石匠锤CLUB HAMMER双面石匠锤DOUBLE FACED CLUB HAMMER ROTBAND-PLUS大锤SLEDGE HAMMER大碎石锤STONE SLEDGE HAMMER劈木锤WOOD SPLITTING HAMMER铺路锤PAVING HAMMER单板锤VENEER HAMMER磁性锤MAGNETIC HAMMER ROTBAND玻璃装配工锤GLAZIERS HAMMER炭化合金瓦锤CARBIDE TILE HAMMER羊角锤CLAW HAMMER电焊敲锤SCALING HAMMER ROTBAND-PLUS无弹力安全锤RECOILLESS HAMMER安全锤SAFETY HAMMER SOFT-PLUS塑料锤PLASTIC HAMMER橡皮锤RUBBER MALLET HARD尼龙锤NYLON HAMMER木锤WOOLEN MALLET铜锤COPPER HAMMER CLUB SHAPE铝锤ALUMINIUM HAMMER ROTBAND桶形铝锤LEAD HAMMER SARREL SHAPE冷凿锤COLD CHISEL HAMMER热凿锤HOT CHISEL HAMMER平底压摸锤SET HAMMER TOP PART压槽铁锤TOP FULLER上型模锤BOTTOM FULLER冲锤PUNCH HAMMER镰刀锤SCYTHE HAMMER锻工钳BLACKSMITH'S TONGS铆钉钳RIVETTING TONGS锥型冲子/中心冲子/销式冲子DRIFT PUNCHES/CENTRE PUNCHES/PIN PUNCHES 自动中心冲子AUTOMATIC CENTRE PUNCH WITH TIPSETPUNCH 冲子组套DRIFTSETTERRIVET 铆钉装配器PUNCHESAND 字母及数字冲子LETTER NUMBERPUNCH装配冲子SETTINGPRVBAR撬杆OCTAGONALFIFER 起钉器NAILCROWBAR撬棍PULLER通用拉马UNIVERSALPATTERN两爪拉马PULLER 2-ARMPATTERN3-ARM PULLER 三爪拉马PATTERN防腐蚀拉马COROSTOP PULLERPULLER快速拉马QUICK-ACTIONPULLER两爪液压拉马UNIVERSAL 2-ARM拉马延长杆EXTENSION FOR PULLERS液压轴杆HYDRAULIC PRESSURE SPINDLE三爪液压拉马UNIVERSAL 2-ARM PULLER拉马套装PULLER SET螺母劈开器NUT SPLITTER液压螺母劈开器NUT SPLITTER HYDRAULIC螺栓提取器STUD EXTRACTOR轴承提取器BALL BEARING EXTRACTOR滚珠轴承提取器套装BALL BEARING EXTRACTOR SET内提取器INTERNAL EXTRACTOR冲击轴承拉马IMPACT BEARING PULLER汽缸拉马CYLINDER LINER PULLER COMPLETE WITH SUPPORT BRACE分离拉马SEPARATOR PULLER轴承分离器BEARING SEPARATOR传动轴轴承拉马DRIVE SHAFT BEARING PULLER分离器及拉马套装SEPARATOR AND PULLER SET拉拔卡盘PULLING CHUCK液压泵HYDRAULIC PUMP液压手泵HYDRAULIC HAND PUMP液压工具拉马1.50 PULLER FOR HUDRAULIC IMPLEMENT1.50液压增力器HYDRAULIC PRESS轮毂拉马WHEEL-HUB PULLER传动轴拉马DRIVE-SHAFT PULLER方向盘拉马STEERING-WHEEL PULLER装配叉DISMANTLING AND ASSEMBLY FORK球头拉拔器BALL JOINT PULLER三爪机滤扳手OIL FILTER HOOK弹簧撑SPRING SPREADER塑料轴承安装套装PROFESSINAL PLASTIC BEARING INSTALLATION SET法兰分离器FLANGE SEPARATORS轨距测量器TRACK ALIGNMENT GAUGE扳手WRENCHES管子切割器PIPE CUTTERS扩口工具FLARING TOOLS弯管机PIPE BENDERS管子工具PLUMBING TOOLS铁皮剪/断线钳TIN SNIPS/BOLT CUTTERS管子清洁设备PIPE CLEANING EQUIPMENT弯管系统PIPE BENDING SYSTEMSSNAP管道扳手PIPE WRENCH ECK-SNAP钢管切割器PIPE CUTTER TUBEX FOR STEEL PIPES生铁管切割器PIPE CUTTER TUBEX FOR CAST IRON PIPES不锈钢管切割器RATCHET PIPE CUTTER NIRO FOR STAINLESS STEEL PIPES 管子修边器PIPE DEBURRING REAMER不锈钢管修边器PIPE DEBURRING REAMER FOR STAINLESS STEEL PIPES扩口工具套装FLARING TOOL SET BOERDEX钢管扩口钳EXPANDER PLIERS FOR COPPER PIPES带滑轨的弯管机PIPE BENDER WITH SLIDE RAIL带滚轴的弯管机PIPE BENDER WITH ROLLER弯管钳PIPE BENDING PLIERS带滑轨的弯管钳PIPE BENDING PLIERS WITH SLIDE RAIL带滚轴的弯管钳PIPE BENDING PLIERS WITH ROLLER手动弯管机MANUAL BENDING TOOL液压弯管机HYDRAULIC PIPE BENDER手动液压弯管机PIPE BENDING MACHINE FOR MANUAL HYDRAULIC OPERATION 电动液压弯管机PIPE BENDING MACHINE FOR ELECTRO HYDRAULIC OPERATION 管道矫直工具PIPE STRAIGHTENING TOOL金属片弯边钳SHEET METAL CRINPING PLIERS折边钳SEAMING PLIERS快速夹取扳手QUICK-CLAMP WRENCH夹管钳GRIPPING PLIERS分级扳手STEPPED KEY复合分级扳手COMBINATION STEPPED KEY铁皮剪TIN SNIPS /HOLE CUTTING SNIPS /PELICAN PATTERN SNIPS断线钳BOLT CUTTER管道清洁软轴FLEXIBLE PIPE CLEANING SHAFT排水管清洁器DRAIN PIPE CLEANER工作台几工作桌WORKBENCHES AND WORK TABLES工具车TOOL TROLLEYS工具柜TOOL CABINETS车间推车WORKSHOP TROLLEYS抽屉柜/箱DRAWER-CABINETS/BOXES衣柜/工作服柜WARDROBES矮橱LOWER CUPBOARD UNIT图纸夹DRAWING HOLDER电源面板PWER SUPPLY PANEL防酸放腐蚀工作台面板六边形工作台HEXAGONAL WORKBENCH带抽屉工作台WORKBENCH WITH DRAWER CABINET塑料抽屉插件PLASTIC DRAWER INSERT工作桌推车WORKSHOP TABLE TROLIEYS工作台WORKBENCH带背板工作台坚固推车TROUGH TROLLEY平板车PLATFORM TROLLEY带手柄平板车PLATFORM TROLLYE WITH HANDLE维护推车SERVICE TROLLEY带工具箱车间推车WORKSHOP TROLLEY WITH TOOL CHEST工具箱TOOL CHEST存放斗STORAGE TRAY卷纸架PAPER ROLL HOLDER垃圾桶WASTE BASKET移动架写字板LECTERN WORKTOP存储盒STORAGE BOXES带门库架CUPBOARD WITH SHELVING WITH DOORS开敞式壁板COMPLETE PANEL SYSTEM WITH SLOTTED PANELS存物柜LOCKER WITH HINGED DOORS滑门橱CUPBOARD WITH SLIDING DOORS电脑柜COMPUTER CABINET桌上设备DESK INSTALLATION移动电脑架PC STAION MOBILE电脑车间组合PC WORKPLACE COMBINATION更衣室条凳CHANGING CUBICLE SEAT BENCH安全橱SAFETY CUPBOARD衣橱CLOTHES LOCKER带凳子的衣橱CLOTHES LOCKER WITH SEAT BENCH消防员衣橱FIREFIGHTER'S CUPBOARD工具橱TOOL CABINET移动式可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER MOBILE 固定可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER STATIONARY分类垃圾收集站WASTE-COLLECTION STATION CONTAINER立式烟灰缸STAND ASHTRAYOCHSENKOPF系列斧头欧洲ILTIS型斧制图用刮刀专业伐木斧快劈斧抢险袖珍刀CAROLUS特殊工具KLANN汽车专用工具弹簧压缩器横杆球头拉拔器轮轴拉马液压手用压力器轴衬提取器发动机锁定工具套装扭距测试仪及设备TORQUE TESTER AND EQUIPMENT扭距倍增器TORQUE MULTIPLIERS扭距角度指示器TORQUE ANGLE INDICATORS特殊DREMO工具SPECIAL DREMO TOOLSDREMOMETER系列扭力工具DREMOMETER TOOLS扭距螺丝刀TORQUE SCREWDRIVERS扭距扳手/扭力扳手TORQUE WRENCHES电子扭距测试仪ELECTRONIC TORQUE TESTERDKD校准遵守DKD准则3-7/3-8/DIN EN ISO 6789RAHSOL DREMOTEC产品校准按照DIN EN ISO 6789标准迷你型扭距扳手DREMOMETER MINIDREMOMETER高强度铝合金扭距扳手含：DREMOMETER 1-12NM /10-100LBF.IN （塑料外表）DREMOMETER 6-30NM /50-270LBF.INDREMOMETER 8-40NM /70-350LBF.INDREMOMETER 20-120NM /15-90LBF.FTDREMOMETER 40-200NM /30-150LBF.FTDREMOMETER 50-300NM /35-220LBF.FTDREMOMETER 80-360NM /60-260LBF.FTDREMOMETER 110-550NM /80-405LBF.FTDREMOMETER 140-760NM /105-560LBF.FTDREMOMETER 520-1000NM /380-730LBF.FTDREMOMETER 750-2000NMDREMOMETER 1500-3000NMDREMOMETER系列棘轮头RATCHET HEADS DREMOMTER扭距限制接合器TORQUE LIMIT UNIT转角仪TORQUE ANGLE INDICATOR圆形插头式扭距扳手（覆盖范围8-1000NM）开口扳子头OPEN END RTTING梅花扳子头RING END RTTING半开口梅花扳子头FLARED END FITTING棘轮头RATCHET HEAD四方头FIXED SQUARE HEAD方形插头式扭距扳手（覆盖范围8-400NM）开口插头RECTANGULAR OPEN END RTTING梅花插头RECTANGULAR RING END RTTING半开口梅花插头RECTANGULAR FLARED END RTTINGTORCOFIX系列带四方驱动的扭距扳手TORCOFIX K扭距扳手（四方头）TORQUE WRENCH TORCOFIX K 含：'方头1-5NM 1/44549-01'方头2-25NM 4549-02 1/4'方头5-50NM 3/84549-05'方头4550-10 10-100NM 1/24550-20 20-200NM 1/2'方头4550-30 60-300NM 1/2'方头4550-40 75-400NM 1/2'方头4550-55 100-550NM 3/4'方头4550-75 140-750NM 3/4'方头TORCOFIX K扭距扳手套装TORCOFIX K TORQUE WRENCH SETTORCOFIX K快速旋转把手QUICK-TURN WITH T-GRIP TORCOFIX K蘑菇头MUSHROOM HEADTORCOFIX Z扭距扳手（圆形插头）TORQUE WRENCH TORCOFIX ZTORCOFIX SE扭距扳手（四方插头）TORQUE WRENCH TORCOFIX SE TORCOFIX FS扭距扳手（可预设扭力值2-200NM）TORQUE WRENCH TORCOFIX FS TORCOFIX UK扭距扳手TORCOFIX UK TORQUE WRENCHTORCOFIX K扭距扳手TORCOFIX K TORQUE WRENCH扭距螺丝刀/扭力螺丝起子TORQUE SCREWDRIVERSFS型扭距螺丝刀范围0.02-13.6NMS型扭距螺丝刀范围0.05-9NMSP型扭距螺丝刀范围10-500CNMTSN预置扭距滑转扳手TSN SLIPPER QORQUE WRENCH 范围3-125NMTBN折弯式扭距扳手TBN BREAKER QORQUE WRENCH 范围0.2-135NMTSP预置扭距滑转扳手TSP SLIPPER QORQUE WRENCH 范围1-10NMTSC预置扭距滑转扳手TSC SLIPPER QORQUE WRENCH 范围1-10NM电线标示系统PLASTIC-TAG MARKING SYSTEM刻度盘/表盘扭距扳手DIAL MEASUREMENT TORQUE WRENCHES适用场合：测试控制维护工作应用环境ADS 4 0.8-4NM 1/4'方头ADS 12D 2.4-12NM 1/4'方头ADS 25 5-25NM 3/8'方头ADS 40 8-40NM 3/8'方头BDS 80E 16-80NM 1/2'方头BDS 200 40-200NM 1/2'方头CDS 400S 80-400NM 3/4'方头DDS 800S 160-800NM 3/4'方头EDS 1400S 280-1400NM 1'方头EDS 2000S 400-2000NM 1'方头88型折弯式扭距扳手TYPE 88 BREAKER TORQUE WRENCH 范围100-1500NM 8800-01 3/4'方头 100-500NM8800-02 3/4'方头 150-700NM8800-03 3/4'方头 300-1000NM8800-04 3/4'方头 700-1500NM8800-06 圆形插头16mm 130-550NM扭距倍增器/扭力放大器/齿轮减速器TORQUE MULTIPLIERS在狭小的空间内获得巨大的扭距输出型号不同范围含1000NM - 47500NM 比例有1：5 1：15 1：15.5 1：25 1：26 1：75 1：125等等数字扭距扳手/数显扭力扳手ELECTRONIC TORQUE WRENCHE-TORC微处理器控制扭距扳手E-TORC ELECTRONIC TORQUE WRENCH TORCOTRONIC数显扭距扳手TORCOTRONIC ELECTRONIC TORQUE WRENCH电子扭距测试仪ELECTRONIC TORSIONS TORQUE TESTER E-TP智能型电子扭距测试仪系列E-TP ELECTRONIC TORSIONS TORQUE TESTER范围包括：0.5-1000NM的测试扭距扳手测试架TORQUE WRENCH TEST FRAMEE-TP打印机E-TP PRINTERE-TP固定架E-TP ADAPTER PLATEE-TP转接器E-TP ADAPTORE-TP软件及数据线E-TP SOFTWARE INCL AND PC-CONNECTION CABLE PLASTIC-CASEE-TP包装箱E-TP。
飞机维修中各类工具中英文对照
.飞机维修中各类工具中英文对照SocketsWrenches/套筒扳手Wrenches开口扳手Open EndWrenches Spline End梅花扳手Wrenches Crowfoot块扳手Wrenches Combination开口/梅花扳手Wrenches Hex六角扳手Ratchet Slab平板棘轮扳手Ratchet Wrenches棘轮扳手Wrenches Torque力矩扳手Wrenches管钳PipeWrenchesAdjustable活动扳手Sockets Six Point六角套筒Sockets Point梅花套筒TwelveSockets Universal万向套筒Adaptor转接头Extension套筒接杆SocketJointUniversal万向转接头Screwdrivers螺刀Screwdrivers快速螺刀FastScrewdrivers Electronic miniature仪表螺刀ScrewdriversPILLIPS十字头螺刀资料Word.ScrewdriversMagnetic磁性螺刀Tip Screwdrivers一字头螺刀Flat Speeders摇把Pliers钳Pliers Needle Nose尖嘴钳Pliers Locking大力钳Safety Wire Twisters保险丝钳Pliers Adjustable Joint鹰嘴钳Plug插头钳ConnectorStrippers Wire剥线钳Pliers Slip-Joint鱼口钳Combination PliersRing Convertible Snap卡环钳Cutters剪线钳DiagonalCrimpers Wire压线钳Tools电气工具Electronic's Lamb)矿灯Safety Lamb(Miner Light Flashing手电对讲机InterphoneIron电烙铁ElectronicEarphone耳机Wrist Static防静电手腕Battery电池资料Word.Charger充电器Speaker扬声器Receptacle电源插座Runner电枪Electronic DrillsElectronic电钻Light Flashing Emergency指挥棒Ultrasonic超声波Tools测量工具MeasuringRulers Steel钢板尺Rulers Tape卷尺Outside Micrometer螺旋卡尺Gauges(Thickness)Feeler塞尺Measuring Cup量杯CaliperDial游标卡尺Gauges表Meter Multi三用表兆欧表Meg OhmMeterDiversiform杂项Mirror反光镜InspectionMagnifier放大镜Tool软杆双爪式机械手FlexibleTwo_claw PickUp Tool软杆磁棒FlexibleMagneticPickUp资料Word.Utility Knife划刀Knife Scraper刮刀(Scissor)剪刀SnipSaw锯Chisels凿子Punch錾子(Spider)Tripod三脚架Hammer Copper铜榔头Iron Hammer铁榔头Hammer Rubber胶榔头Hook弯勾File锉(Pliers)Nipper镊子Tools Removal Pin销钉插拔工具Runner Pneumatic气枪DrillsPneumatic气钻GunRivet铆钉枪(Squirt)Injector注射器Oil Cart滑油加油车CartFluid Hydraulic液压油加油车Grease Gun注油枪Dishcloth抹布资料Word.Glove手套Rope绳索Kit工具箱ToolsRack Tools工具架Jack千斤顶Bar Tommy撬棒Work Ladder工作梯wheel Grinding砂轮Sand paper砂纸TapeAdhesive胶带Tin焊锡SolderingBar Tow拖把Vest Flashing发光背心(Blinkers)Goggle护目镜Belt)Belt(Safety Life安全带增补SPANNERCONBINATION两用扳手SET COMBINATION SPANNER两用扳手套装LONG EXTRACOMBINATION加长型两用扳手SPANNERRATCHET WITHRING梅花棘轮开口扳手OPEN ENDEDSPANNER梅花棘轮开口扳手套装SET OPENENDEDSPANNERWITHRINGRATCHET资料Word.SPANNER RATCHET两用棘轮扳手COMBINATIONSET RATCHET SPANNER两用棘轮扳手套装COMBINATION1/4'1/4'连接物ADAPTORTOOL COMBINATION HOLDING组合支架工具LAMP MINIATURE LED小型发光二极管SPANNER ENDED活动扳手SINGLE OPENSET SPANNER扳手套装MAGNETOSPANNER JAW ENDED OPEN单开口扳手/呆扳手SINGLE SPANNERENDED双开口扳手DOUBLEOPENSETSPANNER OPEN ENDED双开口扳手套装DOUBLE）（OPENNUT SPANNER扩口螺母扳手PLARE SPANNERRING半月型梅花扳手HALF-MOON）SHORT SPANNER（双头梅花扳手（短）DOUBLE ENDED）LONGSPANNER（ENDED双头梅花扳手（长）DOUBLE PATTERN STRAIGHT RING SPANNERFLAT平头梅花扳手（直）SPANNERSLOGGING OPEN ENDED开口敲击扳手SPANNERSLOGGING梅花敲击扳手RINGSPANNER RING SLOGGING高颈梅花敲击扳手DEEP AFFSET）PATTERN SPANNER（STRAIGHTRING直头梅花扳手DEEP TUBE延长管EXTENSIONSPANNER爪型扳手CROWFOOTWRENCHHEAD SWIVELCOMBINATION两用活头扳手资料Word.T SLIDINGSWIVEL HANDLE WITH活结T型扳手WRENCH套筒扳手SOCKETWRENCH SOCKET弯头套筒扳手ANGLED WRENCHSOCKET DOUBLE ENDED双头套筒扳手BARTOMMY旋棒BARTOMMY分节旋棒STEPPED3C-HANDLEWITH WRENCH3C把手套筒扳手SOCKET型及磁性套筒扳手TMAGNET T-HANDLE ANDSOCKET WRENCH WITH LUG WITH钩头扳手HOCKSPANNERSPANNER带销扳手PINADJUSTABLEWITH FACESPANNER可调式两爪钩扳手CALIPER SOCKETHEXAGON1/4'标准六角套筒SOCKET LONG PATTERN1/4'加长六角套筒HEXAGONRATCHETS棘轮扳手SOCKETS套筒SETS套筒套装SOCKETSRATCHETSFRICTION摩擦棘轮扳手TOOLS IMPACT冲击工具BITS旋具头WRENCHESTORQUE扭矩扳手PROFILEUD SOCKET1/4梅花套筒资料Word.六角套筒1/4SCREWS HEADSOCKET FOR PROTRUDING星型套筒一字，十字，星型，六角旋具套筒1/4RATCHET'REVERSIBLE1/4'双向棘轮套筒扳手1/4T-HANDLEWITH T柄棘轮扳手RATCHET HANDLEWITHOUT HAND RATCHET手用棘轮头3/8TO1/41/4转3/8转换接头CONVERTERT WITH SLIDINGT型滑动头手柄TOMMY BAR EXTENSION活动延长杆FLEXIBLE EXTENSION通用延长杆UNIVERSAL-JOINT COUPLER四方驱动连接头SQUARE-DRIVE1/4 JOINT万向接头UNIVERSAL1/4 HANDLESWIVEL活动头手柄MAGNETICWITH RAIL SOCKET套筒固定夹一字，十字，星型，六角旋具套筒3/83/8SOCKET HEXAGON3/8六角套筒PROFILE UD3/8梅花套筒SOCKET RATCHETPLASTIC塑料棘轮扳手ADAPTOR旋具头接头BITRATCHET旋具头棘轮扳手BIT SCREWDRIVERBIT旋具头螺丝起子EXTENSIONBIT旋具头延长杆资料Word.BITS旋具头SCREWDRIVERSOCKET风动套筒IMPACTSOCKET FOR IMPACT风动套筒附件ACCESSORIESDRIVER INPACTHAND-OPERATED手动操作冲击手柄摩擦式梅花棘轮扳手BI-HEXAGON WITHRATCHET WITH RINGFRICTION TYPE 摩擦式四方棘轮扳手RING SQUARE RATCHET WITHFRICTION TYPEBI-HEXAGONRATCHET/尖尾扳手CONSTRUCTION安装扳手0.6-5.4NMHANDLE TORQUE SCREWDRIVER0.6-5.4NM扭力螺丝起子SCREWSHEAD SLOTTED3C一字螺丝起子3C-SCREWDRIVER FORPH CRUCIFORM HEADPH螺丝起子3C-SCREWDRIVER FOR3C十字米字螺丝起子3C星型螺丝起子3C球头六角螺丝起子3CSCREWSHEAD SET件螺丝起子套装FOR5件/6件/7件/155 SCREWDRIVERELECTRONIC电工螺丝旗子HANDLE WITH WOODEN木柄螺丝起子SCREWDRIVERSDEMAGNETIZER AND消磁器磁化/MAGNETIZERAWLBLADED SQUARE方刃锥子T-HANDLE SCREWDRIVER WITHHEXAGONT型六角螺丝起子T-HANDLEWITH KEYSOCKETHEXAGONT型六角扳手资料Word.KEY HEXAGON SOCKET六角扳手KEY HEXAGON SOCKET加长六角扳手EXTRA LONG加长球头六角扳手SET SOCKET KEY六角扳手套装HEXAGONT-HANDLE WITHT型星形螺丝起子SCREWDRIVER SCREWDRIVER曲柄螺丝起子CRANKEDGARGE量规TESTER LIGHT车灯测电笔CAR6-24V TESTER6-24伏测电笔VOLTAGE150-250VTESTER150-250伏测电笔VOLTAGE3-PIECESET，3件套装PLIERS钳子PIECE48WITH48件套UNIVERSAL PLIERS ASSORTMENT万能手钳PLIERS SMALL COMBINATION小钢丝钳）PATTERN（GERMAN钢丝钳（德式）COMBINATION PLIERS）PATTERNEURO钢丝钳（欧式）COMBINATION PLIERS（PLIERSCOMBINATION强力钢丝钳POWERPLACTICFOR SIDE CUTTERS塑料水口钳）PATTERN（SWEDISH CUTTERS剪钳（瑞典款式）SIDE CUTTERS SIDEELECTRICIAN电工剪钳'S）PATTERN CUTTERS（AMERICAN剪钳（美国款式）POWER SIDE CUTTERS SIDE杠杆剪钳LEVER-ACTIONNIPPERSCUTTING ENDLEVER-ACTION杠杆顶剪钳资料Word.PINCERS核头钳TOWERPINCERS拨钉钳PLIERS NOSE平头钳FLATPLIERSNOSE圆头钳ROUNDPLIERSNOSE直头尖嘴钳LONG弯头尖嘴钳PLIERSTELEPHONE钳PLIERSTRIPLE-FUNCTION强力尖嘴钳PATTERN STRAIGHT PLIERS直口机修工钳MECHANICSPATTERN PLIER ANGLED曲口机修工钳MECHANICSPATTERN OFFSETPLIER偏口机修工钳MECHANICS30WITH30度平圆机修钳MECHANICS PLIERKNIFECABLE电缆刀KNIFECABLE ELECTRICIAN'S电工电缆刀防静电专用钳子PLIERS电子钳ELECTRONICPLIERS MINIATURE ELECTRONIC迷你电子钳电子剥线防静电剪钳/电子平头钳//电子剪钳/防静电尖嘴钳/防静电顶切钳钳CUTTERS电缆剪钳CABLESCISSORSUNIVERSAL小型万用剪SMALLKNIFECABLE UNIVERSAL万用电缆刀资料Word.ANTOMATIC PLIERS自动剥线钳STRIPPINGPLIERS剥线钳STRIPPINGPLIERS STRIPPING固定剥线钳STRIP-FIXSTRIPPER剥线工具WIRESTRIPPER WIRE高效剥线钳HIGH-PERFORMANCE数据传输电缆精确剥线钳CABLESDATA STRIPPER FOR PRECISION WIRE CABLESCOAXIAL FOR同轴电缆剥线钳WIRE STRIPPER STRIPPERVARNISH绝缘剥漆钳INSULATINGKNIFE WIRE STRIPPING剥线刀TAPE绝缘胶带INSULATINGPLIERS压线钳CRIMPINGPLIERS CRIMPING锁把式压线钳LOCK-GRIPPLIERS END-SLEEVE端子压线钳WIREPLIERSCRIMPING MODULAR LOCK-GRIP模块压线夹钳PLIERSCRIMPING模块压线钳MODULARPLIERS PRECISION CRIMPING精确压线钳）ONSHAFTS CIRCLIP PLIERS（外卡簧钳（轴用）EXTERNAL弯头外卡簧钳（轴用）直头/）INBORES卡簧钳（孔用）INTERNAL CIRCLIPPLIERS（弯头卡簧钳（孔用）/直头重型卡簧钳大型/资料Word.X-GRIP型把XPLIERS大力钳LOCK-GRIPPLIERS JAW LOCK-GRIP平行钳夹大力钳PARALLELPLIERS LOCKING宽口大力钳WIDE JAWCLAMP SLIDE滑行杆式大力钳LOCK-GRIPGLUEING FOR固定大力钳GRIP WRENCHCLAMPWORKBENCH机械工作台钳MACHINECLAMPWELDING焊接大力钳LOCK-GRIPCLAMPWELDING LOCK-GRIP TUBE管子焊接大力钳CLAMPC型大力钳LOCK-GRIP C种设置）/5（PLIERS7种设置水泵钳UNIVERSALPLIERS WATER PUMP水泵钳PLIERS PUMPWATER特殊水泵钳SPECIAL可调式高速管子钳ADJUSTER SCREW WRENCH WITH HIGH-SPEEDPIPE CURVEDWRENCH HIGH-SPEED PIPE高速曲口管子钳WRENCH CHAINPIPE迷你链式管子钳MINIWRENCH CHANIN PIPE链钳WRENCH PIPE重型管子钳STILLSONCUTTERSBOLT断线钳件）/8/6件件钳子套装（3件/4TOOLSSAFETY INSULATEDVDEVDE绝缘安全电工工具资料Word.适以及VDE6802004IEC60900：VDE绝缘标准符合DIN EN60900）DC1500VAC1000V合在高压区安全工作（六角）//星型/十字/米字（一字VDE绝缘螺丝起子VDE SCREWDRIVER绝缘起子套装VDEDETECTOR/TESTERVOLTAGE电压测试器电压传感器/ WRENCHTORQUE绝缘扭力扳手VDERATCHETREVERSIBLE绝缘双向棘轮扳手VDEHEXAGONALSOCKET绝缘六角套筒VDESLCKETBIT SCREWDRIVER绝缘旋具头套筒VDET-HANDLE T型绝缘扳手VDEEXTENSION绝缘延长杆VDE件）/108/14件/8绝缘电工工具组套（3件件绝缘手柄套筒扳手3CVEDHANDLE3C WRENCHWITH VDE SOCKET绝缘梅花扳手OFFSET WITH DEEPVDE SINGLE-ENDED RING SPANNERSPANNER OPEN绝缘开口扳手VDESINGLE-ENDEDHACKSAW绝缘钢锯VDEKNIFECABLE绝缘电缆刀VDESHEARS绝缘电缆剪CABLECUTTERSCABLE棘轮式绝缘电缆剪钳SHEARSCABLE VDEVDE绝缘电缆剪资料Word.绝//绝缘斜口钳绝缘水泵钳/绝缘固定剥线钳//绝缘强力钢丝钳绝缘剥线钳绝缘弯头尖嘴钳//绝缘直头尖嘴钳缘电工斜口钳/绝缘平口钳/绝缘圆头钳SHEET COVER绝缘橡胶垫VDE RUBBERVDEGLOVESSAFETY'ELECTRICIANSS VDE绝缘电工安全手套VDE CLAMPSPLASTIC绝缘塑料夹VDEWRENCHESWHEEL车轮扳手WRENCHWHEEL WAY十字扳手4LEVERTYRE撬棒TOOS HUBCAP RENOVING轮毂罩移除工具PLIERS配重钳BALANCE-WEINHTPLIERS制动弹簧钳BRAKE-SPRINGSPRINGS BRAKE-CABLE闸线弹簧钳PLIERS FORBRUSH制动钳刷BRAKE-CALIPERSQUAREWITH DRAIN-PLUG WRENCH放油塞扳手（四方）CANSOIL油壶WRENCH过滤器扳手UNIVERSALFILTERWRENCH皮带钳PULLEYGRUNDER阀门研磨机VALVETOOSLAPPING VALVE阀门研磨工具FINISH PLIERS GUNMETAL油封钳VALVE-SEAL活塞环压缩器/汽缸NICKEL-PLATDEBRIGHT COMPRESSORSPRINGVALVE资料Word.PLIERS RING活塞环钳PISTONPLIERS CLIP软管夹钳HOSEPULLERTERMINAL电极拉马BATTERYTESTERBATTERY电池测试器SOCKETPLUG火花塞套筒SPARKWRENCHSOCKET PLUG火花塞套筒扳手SPARKBRUSHSPARK-PLUG火花塞刷PUNCH SPECIAL PIN特殊尖冲凿SPREADER弹簧撑开器SPRINGREMOVER JOINTUNIVERSAL球头拉拔器BALLCANISTER通用罐UMIVERSALTESTER防冻测试器ANTI-FREEZE PLIERSINSTALLATION安装钳LIFTERSUCTION吸盘TOOLPICK-UP磁性拾取工具MAGNETICNIBBER金属片切割器SNIPS LEVER-ACTION TIN杠杆剪切机PLIERS打孔钳PUNCHHAMMERRUBBER橡胶锤HAMMER PLASTIC塑料锤HAMMER无后坐力锤RECOILLESSHAMMERPEIN BALLSENGINEERS钳工球头锤'资料Word.HAMMER'S钳工锤ENGINEERSSCRAPER平面刮刀FLATSCRAPERHOLLOW-GROUND三角空心刮刀THREE-EDGED SCRAPERFLAT-GROUND三角实心刮刀THREE-EDGED SCRAPERGASKET密封刮刀FILEHAND平锉FILEROUND圆锉FILETRIANGULAR三角锉FILE半圆锉HALF-ROUND件套装6锉类PUNCHESCENTRE PUNCHES/CHISELS/DRIFT中心冲/凿/开口销冲HACKSAW钢锯SAW栓孔锯KEYHOLESAWSMALL METAL小金属锯HACKSAW JUNIOR小PUK钢锯PUK锯HOBBY）100/125/150mm台钳/台虎钳METALWORKINGVICE（米）/8/5米3TAPE钢卷尺STEEL MEASURE（米GAUGE VALVE阀塞尺FEELER塞尺GAUGE SPARK PLUG火花塞塞尺GAUGETHREAD螺纹规资料Word.CALLIPER VERNIER游标卡尺POCKETCALLIPER数显游标卡尺DIGITALSCRIBER划线器TWEEZERS镊子TWEEZERSCROSSLOCK十字镊子EXTRACTORBOLT螺钉取出器SETEXTRACTOR断螺钉取出器套装SCREW SPLITTERNUT机械螺母破开器MECHANICAL EXTRACTOR INSERTER ANDSTUD螺栓插入及取出器FILE丝锥THREADCUTTER管子割刀PIPECUTTER PIPE自动切割机AUTOMATICCUTTER PIPE链式切管机CHAINPLIERSTRAP虹吸扳手SIPHONBRUSHWIRE钢丝刷BRUSH FILE CLEANING锉刀清洁刷SCISSORS裁缝剪TAILORSLAMPINSPECTION发光二极管井下检查灯LED LAMP INSPECTION井下检查灯LIGHT LED WORK发光二极管工作灯ROTBAND-PLUSHAMMER ENGINEERS工程锤HAMMERPEIN'工程圆头锤ENGINEERSBALL资料Word.HICKORY HANDLE桃木备用手柄SPARE ROTBAND-PLUS'HAMMER工匠锤JOINERS HAMMER石匠锤CLUBROTBAND-PLUSHAMMER FACED CLUB双面石匠锤DOUBLE HAMMERSLEDGE大锤HAMMERSLEDGE大碎石锤STONEHAMMERSPLITTING劈木锤WOODHAMMER铺路锤PAVINGHAMMER单板锤VENEERROTBAND MAGNETIC HAMMER磁性锤HAMMER玻璃装配工锤GLAZIERSHAMMER TILE炭化合金瓦锤CARBIDEHAMMER羊角锤CLAWROTBAND-PLUSHAMMER电焊敲锤SCALING HAMMERRECOILLESS无弹力安全锤SOFT-PLUS SAFETY安全锤HAMMERHAMMER塑料锤PLASTICHARD MALLET橡皮锤RUBBERHAMMERNYLON尼龙锤MALLET WOOLEN木锤SHAPECLUB铜锤COPPER HAMMER ROTBANDHAMMER ALUMINIUM铝锤资料Word.SHAPE SARREL桶形铝锤LEAD HAMMERHAMMER CHISEL冷凿锤COLDHAMMERCHISEL热凿锤HOTPARTTOP SET HAMMER平底压摸锤FULLERTOP压槽铁锤FULLERBOTTOM上型模锤HAMMERPUNCH冲锤HAMMER镰刀锤SCYTHETONGS BLACKSMITH'S锻工钳TONGS铆钉钳RIVETTING销式冲子//中心冲子锥型冲子DRIFTPUNCHESPUNCHES/PIN PUNCHES/CENTRETIP PUNCH WITHCENTRE自动中心冲子AUTOMATIC SET PUNCH冲子组套DRIFTSETTER铆钉装配器RIVETPUNCHESLETTER AND NUMBER字母及数字冲子PUNCH装配冲子SETTINGPRVBAR撬杆OCTAGONAL起钉器NAILFIFERCROWBAR撬棍PULLER通用拉马UNIVERSALPATTERN2-ARMPULLER两爪拉马资料Word.PATTERN3-ARM三爪拉马PULLERPATTERN PULLER防腐蚀拉马COROSTOPPULLER快速拉马QUICK-ACTIONPULLER2-ARM两爪液压拉马UNIVERSALPULLERSFOR拉马延长杆EXTENSIONSPINDLEPRESSURE液压轴杆HYDRAULICPULLER2-ARM三爪液压拉马UNIVERSALSETPULLER拉马套装SPLITTER NUT螺母劈开器HYDRAULIC NUT SPLITTER液压螺母劈开器EXTRACTOR螺栓提取器STUDEXTRACTOR BEARING轴承提取器BALLSET EXTRACTOR滚珠轴承提取器套装BALL BEARING EXTRACTORINTERNAL提取器PULLERBEARING冲击轴承拉马IMPACT汽缸拉马BRACE WITH SUPPORT LINERPULLER COMPLETE CYLINDER PULLER分离拉马SEPARATORSEPARATORBEARING轴承分离器PULLER SHAFT BEARING传动轴轴承拉马DRIVESETPULLER分离器及拉马套装SEPARATORANDCHUCKPULLING拉拔卡盘资料Word.PUMP液压泵HYDRAULICPUMP HAND液压手泵HYDRAULICIMPLEMENT1.50HUDRAULIC PULLER FOR液压工具拉马1.50 PRESSHYDRAULIC液压增力器PULLERWHEEL-HUB轮毂拉马PULLERDRIVE-SHAFT传动轴拉马PULLERSTEERING-WHEEL方向盘拉马FORK AND ASSEMBLY装配叉DISMANTLINGPULLER BALL JOINT球头拉拔器HOOK FILTER三爪机滤扳手OILSPREADER弹簧撑SPRING塑料轴承安装套装SETINSTALLATION PLASTIC BEARING PROFESSINAL SEPARATORSFLANGE法兰分离器GAUGE轨距测量器TRACKALIGNMENTWRENCHES扳手CUTTERS管子切割器PIPETOOLS扩口工具FLARINGBENDERSPIPE弯管机TOOLS PLUMBING管子工具CUTTERSSNIPS/BOLT铁皮剪/断线钳TINEQUIPMENTCLEANING PIPE管子清洁设备资料Word.SYSTEMSBENDING弯管系统PIPEECK-SNAP PIPE管道扳手WRENCHSNAPPIPES FOR STEELPIPE CUTTER TUBEX钢管切割器PIPES CAST IRON TUBEX FOR生铁管切割器PIPE CUTTER不锈钢管切割器PIPES STEELNIRO FOR STAINLESSRATCHET PIPE CUTTER REAMER DEBURRING管子修边器PIPE不锈钢管修边器PIPESSTEEL FOR STAINLESS PIPE DEBURRING REAMER BOERDEXSET FLARING TOOL扩口工具套装PIPESCOPPER FOR钢管扩口钳EXPANDER PLIERSRAIL WITH SLIDEBENDER带滑轨的弯管机PIPEROLLER BENDER WITH带滚轴的弯管机PIPEPLIERS BENDING弯管钳PIPERAILSLIDE PLIERS WITH带滑轨的弯管钳PIPE BENDINGROLLERWITH PLIERS BENDING带滚轴的弯管钳PIPETOOL MANUAL BENDING手动弯管机BENDER PIPEHYDRAULIC液压弯管机手动液压弯管机OPERATION MANUALHYDRAULIC PIPEBENDING MACHINEFOR电动液压弯管机OPERATIONHYDRAULIC ELECTROFORMACHINEBENDINGPIPE资料Word.TOOL STRAIGHTENING管道矫直工具PIPEPLIERSCRINPING金属片弯边钳SHEET METALPLIERSSEAMING折边钳WRENCHQUICK-CLAMP快速夹取扳手PLIERSGRIPPING夹管钳KEYSTEPPED分级扳手KEYSTEPPED复合分级扳手COMBINATION铁皮剪SNIPS/PELICAN PATTERN/HOLE CUTTING SNIPS TIN SNIPS CUTTER断线钳BOLTSHAFT PIPE CLEANING管道清洁软轴FLEXIBLECLEANERDRAIN PIPE排水管清洁器TABLES WORK工作台几工作桌WORKBENCHES ANDTROLLEYSTOOL工具车CABINETS工具柜TOOLTROLLEYS车间推车WORKSHOPDRAWER-CABINETS/BOXES抽屉柜/箱WARDROBES衣柜工作服柜/UNITCUPBOARD矮橱LOWERHOLDERDRAWING图纸夹PANELSUPPLY电源面板PWER防酸放腐蚀工作台面板资料Word.WORKBENCH六边形工作台HEXAGONALCABINET DRAWER带抽屉工作台WORKBENCH WITH INSERT DRAWER塑料抽屉插件PLASTIC TROLIEYSTABLE工作桌推车WORKSHOPWORKBENCH工作台带背板工作台TROLLEYTROUGH坚固推车TROLLEYPLATFORM平板车HANDLEWITH TROLLYE带手柄平板车PLATFORM TROLLEYSERVICE维护推车CHEST WITH TOOL带工具箱车间推车WORKSHOP TROLLEY CHEST工具箱TOOLTRAY存放斗STORAGEHOLDER ROLL卷纸架PAPERBASKET垃圾桶WASTEWORKTOPLECTERN移动架写字板BOXESSTORAGE存储盒DOORS SHELVING WITHWITH带门库架CUPBOARD PANELSSLOTTED PANEL SYSTEM WITH开敞式壁板COMPLETE DOORS WITH HINGED存物柜LOCKERDOORSSLIDING滑门橱CUPBOARDWITH CABINETCOMPUTER电脑柜资料Word.INSTALLATIONDESK桌上设备MOBILESTAION移动电脑架PC COMBINATIONWORKPLACE电脑车间组合PCBENCH CUBICLE SEAT更衣室条凳CHANGINGCUPBOARD安全橱SAFETYLOCKER衣橱CLOTHESBENCH SEATCLOTHES LOCKER WITH带凳子的衣橱CUPBOARDS消防员衣橱FIREFIGHTER'CABINETTOOL工具橱移动式可回收物品垃圾收集箱MOBILEWASTE-COLLECTIONCONTAINERRECYCLING固定可回收物品垃圾收集箱STATIONARY CONTAINERWASTE-COLLECTIONRECYCLING CONTAINERSTATION分类垃圾收集站WASTE-COLLECTION ASHTRAYSTAND立式烟灰缸系列斧头OCHSENKOPF型斧ILTIS欧洲制图用刮刀专业伐木斧快劈斧抢险袖珍刀特殊工具CAROLUS资料Word.汽车专用工具KLANN弹簧压缩器横杆球头拉拔器轮轴拉马液压手用压力器轴衬提取器发动机锁定工具套装EQUIPMENTAND TORQUE TESTER扭距测试仪及设备MULTIPLIERSTORQUE扭距倍增器INDICATORSANGLE扭距角度指示器TORQUETOOLS SPECIAL DREMO特殊DREMO工具TOOLS DREMOMETER系列扭力工具DREMOMETER SCREWDRIVERS扭距螺丝刀TORQUEWRENCHES扭力扳手TORQUE扭距扳手/ TESTERTORQUE电子扭距测试仪ELECTRONIC6789ISO EN准则DKD校准遵守DKD3-7/3-8/DIN标准6789ISO DREMOTEC产品校准按照DIN ENRAHSOL MINI迷你型扭距扳手DREMOMETER含：高强度铝合金扭距扳手DREMOMETER（塑料外表）1-12NM/10-100LBF.INDREMOMETER/50-270LBF.IN6-30NM DREMOMETER/70-350LBF.IN8-40NM DREMOMETER资料Word./15-90LBF.FT20-120NMDREMOMETER/30-150LBF.FT40-200NMDREMOMETER/35-220LBF.FT50-300NMDREMOMETER/60-260LBF.FT80-360NM DREMOMETER/80-405LBF.FT110-550NM DREMOMETER/105-560LBF.FT140-760NM DREMOMETER/380-730LBF.FT520-1000NM DREMOMETER750-2000NMDREMOMETER1500-3000NMDREMOMETERDREMOMTER RATCHET HEADSDREMOMETER系列棘轮头UNIT TORQUE LIMIT扭距限制接合器INDICATOR ANGLE转角仪TORQUE）8-1000NM圆形插头式扭距扳手（覆盖围RTTING END开口扳子头OPENRTTINGEND梅花扳子头RINGFITTINGEND半开口梅花扳子头FLAREDHEAD棘轮头RATCHETHEAD FIXED SQUARE四方头）8-400NM方形插头式扭距扳手（覆盖围RTTINGEND RECTANGULAR OPEN开口插头RTTING END梅花插头RECTANGULARRINGRTTINGEND FLAREDRECTANGULAR半开口梅花插头资料Word.系列带四方驱动的扭距扳手TORCOFIX含：TORCOFIX K扭距扳手（四方头）TORQUE WRENCH TORCOFIX K '方头1/41-5NM4549-01'方头1/42-25NM4549-02'方头3/85-50NM4549-05'方头1/210-100NM4550-10'方头1/220-200NM4550-20'方头1/260-300NM4550-30'方头1/24550-4075-400NM'方头3/44550-55100-550NM'方头3/44550-75140-750NMSETWRENCH TORQUE TORCOFIX K扭距扳手套装TORCOFIX K快速旋转把手KTORCOFIXK T-GRIP TORCOFIXQUICK-TURN WITHHEAD蘑菇头MUSHROOMZ TORCOFIX扭距扳手（圆形插头）TORQUE WRENCHZTORCOFIX SETORCOFIX TORQUE WRENCH TORCOFIX SE扭距扳手（四方插头））2-200NM TORCOFIXFS扭距扳手（可预设扭力值FS WRENCH TORCOFIXTORQUEWRENCHTORQUE TORCOFIX UK扭距扳手TORCOFIX UK WRENCHTORQUE扭距扳手TORCOFIX KTORCOFIX K SCREWDRIVERSTORQUE扭力螺丝起子/扭距螺丝刀资料Word.0.02-13.6NM围FS型扭距螺丝刀0.05-9NM围S型扭距螺丝刀10-500CNM围SP型扭距螺丝刀3-125NM围WRENCH TSN SLIPPER QORQUETSN预置扭距滑转扳手围WRENCHTBN BREAKER QORQUETBN折弯式扭距扳手0.2-135NM1-10NM围WRENCH SLIPPER QORQUE TSP预置扭距滑转扳手TSP1-10NM围QORQUE WRENCH TSC预置扭距滑转扳手TSCSLIPPER SYSTEMMARKING电线标示系统PLASTIC-TAGWRENCHESTORQUE MEASUREMENT刻度盘/表盘扭距扳手DIAL维护工作应用环境控制适用场合：测试'方头1/40.8-4NM ADS4'方头1/42.4-12NM ADS12D'方头3/85-25NM ADS25'方头3/8ADS408-40NM'方头1/280E16-80NMBDS'方头1/240-200NM BDS200'方头3/480-400NM CDS400S'方头3/4800S160-800NMDDS'方头1280-1400NM1400SEDS'方头400-2000NM1EDS2000S资料Word.围TORQUE WRENCH88BREAKER88型折弯式扭距扳手TYPE100-1500NM 100-500NM3/4'方头8800-01150-700NM3/4'方头8800-02300-1000NM3/4'方头8800-03700-1500NM3/4'方头8800-04130-550NM16mm圆形插头8800-06MULTIPLIERSTORQUE/扭力放大器/齿轮减速器扭距倍增器型号不同围含在狭小的空间获得巨大的扭距输出47500NM1000NM-等等1251：261：751：151：15.51：251：比例有1：5WRENCH TORQUE数字扭距扳手/数显扭力扳手ELECTRONIC微处理器控制扭距扳手E-TORCWRENCHTORQUE E-TORC ELECTRONIC数显扭距扳手TORCOTRONICWRENCHTORQUE ELECTRONIC TORCOTRONIC E-TP TESTERTORQUE电子扭距测试仪ELECTRONIC TORSIONS智能型电子扭距测试仪系列0.5-1000NM围包括：TESTER TORQUE TORSIONSE-TP ELECTRONIC的测试FRAMETEST WRENCH扭距扳手测试架TORQUEPRINTERE-TP打印机E-TP资料Word.PLATE ADAPTERE-TP固定架E-TPADAPTORE-TP E-TP转接器软件及数据线E-TPCABLEPC-CONNECTION E-TP SOFTWAREINCL AND PLASTIC-CASE E-TP包装箱E-TP资料Word。
飞机常用工具英语
adjustable wrench 活(动)扳手, 可调扳手coach wrench 活(动)扳手, 可调扳手monkey wrench 活(动)扳手, 可调扳手adjustable flat wrench 扁平活动扳手adjustable tap wrench 可调丝锥扳手Allen wrench 通用板手alligator wrench 管扳手, 管钳angle wrench 斜口扳手bent wrench 弯头板手box wrench 套筒扳手brace wrench 曲柄头扳手breaker point wrench 电流开关扳手bulldog wrench 管子扳手carriage wrench 套筒板手chuck wrench 卡盘扳手circular ended wrench 套筒扳手claw wrench 钩形扳手closed-end wrench 闭口扳手coach wrench 活动扳手construction wrench 大型安装扳手cylinder wrench 圆筒扳手deep socket wrench 长套管型套筒板手diagonal wrench 活扳手, 瑞典式扳手double end "alligator type "wrench 双头鳄口扳手, 双头管扳手double hexagon end cap wrench 六角螺帽双头扳手double hexagon opening double offset box socket wrench 双头弯脖梅花扳手double hexgonal S-shaped closed double head wrench 套六角环形两头固定扳手 double square closed single head wrench 套方环形一头固定扳手double-head wrench 双头扳手electric socket wrench 套筒电扳手electrode wrench 电极扳手end wrench 平板手flange wrench 凸缘扳手fork wrench 叉形板手free box wrench 活套筒扳手free lever hexagonal fixed socket wrench 活柄六角固定套筒扳手free lever swinging socket wrench 活柄活动套筒扳手fuse wrench 引信扳手grip wrench 管子钳head bent adjustable wrench 弯头活动扳手hexagonal closed double bead wrench 六角环形双头扳手hexagonal inserted handle box wrench 六角插柄套筒扳手hexagonal socket wrench 六角套筒扳手hose wrench 软管扳手hub wrench 轮毂螺母扳手impact wrench 拧紧扳手, 套筒[机动]板手, 冲头machine wrench 机器板手main bearing wrench 主轴承扳手male wrench 套筒扳手monkey wrench 管子钳, 活动板手monkey adjustable wrench 活动扳手monkey screw wrench 活扳手motor wrench 管子钳multiple-dimensioned double head wrench 多尺度双头扳手 nozzle wrench 喷嘴扳手nut wrench 螺母扳手, 扳子offset wrench 斜口扳手off-set pattern socket wrench 弯脖套筒扳手open end wrench 开口板手packing nut wrench 填密螺母扳手pin face wrench 叉形带销扳手pipe wrench 管扳手, 管钳子pipe spanner wrench 管(子)钳piston wrench 活塞扳手plug wrench 火花塞专用扳手pneumatic nut wrench 风动螺母扳手propeller shaft turning wrench 螺旋桨轴扳手ratchet wrench 棘轮扳手rear suspension wrench 后悬挂螺母扳手rear-wheel bearing nut wrench 后轮轴承螺母扳手rim wrench 轮缘扳手roll grip pipe wrench 链条管子钳screw wrench 螺钉扳手set-screw wrench 止动螺钉扳手, 固位螺钉板手shifting wrench 活口扳手single-pin type spanner wrench 单销式扳手sleeve-pipe wrench 套筒扳手snap-on socket wrench 有爪套筒扳手socket off-set wrench 弯头套筒扳手socket ratchet wrench 套筒棘轮扳手solid wrench 死扳手, 呆板手spanner wrench 活动扳手, 开脚板手, 插头[销]板手spark plug socket wrench 火花塞(套筒)扳手spider wrench 星形套筒扳手square box wrench 方套筒扳手square head wrench 方头螺栓扳手square inserted handle box wrench 四方插柄套筒扳手square normal closed double head wrench 四方环形双头扳手square single end tubular wrench 四方单头套筒扳手square socket wrench 方套筒扳手square S-shaped closed double head wrench S形四方环形双头扳手 straddle wrench 叉形扳手straight shank socket wrench 直柄套筒扳手tap wrench 铰杠; 丝锥扳手, 螺丝攻板手T-handle square fixed socket wrench 丁字柄四方固定套筒扳手tommy wrench 螺旋头部用(活动)杆(如虎钳上)套筒扳手tool-post wrench 刀架扳手torque wrench 转矩扳手torque measuring wrench 转矩指示扳手track wrench 轨道扳钳union wrench 联管节扳手, 管接头板手universal socket wrench 万能套筒扳手wheel wrench 轮扳。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
图纸夹 垃圾桶 分类垃圾收集站 通用罐 汽缸/活塞环压缩器 划线器 铆钉装配器 装配叉 弹簧撑 塑料轴承安装套装 特殊DREMO工具 DREMOMETER系列扭力工具 扭距限制接合器 电线标示系统 扭距倍增器/扭力放大器/齿轮减速器 E-TP打印机 E-TP转接器 E-TP软件及数据线 电源面板
Drawing Holder Waste Basket Waste-Collection Station Container Umiversal Canister Valve Spring Compressor Bright Nickel-Platde Scriber Rivet Setter Dismantling And Assembly Fork Spring Spreader Professinal Plastic Bearing Installation Set Special Dremo Tools Dremometer Tools Limit Unit Plastic-Tag Marking System Torque Multipliers E-Tp Printer E-Tp Adaptor E-Tp Software Incl And Pc-Connection Cable Power Supply Panel
杂项 Diversiform
中文名称 英文名称
吸盘 拉拔卡盘 磁性拾取工具 软杆双爪式机械手 镊子 十字镊子 反光镜 放大镜 丝锥 方刃锥子 凿子 弯勾 气枪 气钻 铆钉枪 注射器 滑油加油车 液压油加油车 注油枪 抹布 手套 发光背心 护目镜 安全带 绳索 千斤顶 砂轮 砂纸 胶带 绝缘胶带 VDE绝缘橡胶垫 绝缘塑料夹 焊锡 磁化/消磁器 VDE绝缘电工安全手套 制动钳刷 油壶 火花塞刷 钢丝刷 锉刀清洁刷 管道清洁软轴 排水管清洁器 管子清洁设备 立式烟灰缸 桌上设备
Suction Lifter Pulling Chuck Magnetic Pick-Up Tool Flexible Two_claw Pick Up Tool Tweezers Crosslock Tweezers Inspection Mirror Magnifier Thread File Square Bladed Awl Chisels Hook Pneumatic Runner Pneumatic Drills Rivet Gun Injector (Squirt) Oil Cart Hydraulic Fluid Cart Grease Gun Dishcloth Glove Flashing Vest Goggle (Blinope Jack Grinding wheel Sand paper Adhesive Tape Insulating Tape VDE Rubber Cover Sheet VDE Plastic Clamps Soldering Tin Magnetizer And Demagnetizer VDE Electricians’S Safety Gloves Brake-Caliper Brush Oil Cans Spark-Plug Brush Wire Brush File Cleaning Brush Flexible Pipe Cleaning Shaft Drain Pipe Cleaner Pipe Cleaning Equipment Stand Ashtray Desk Installation