964c-datasheet臭氧检测仪,在线臭氧分析仪,臭氧分析仪,臭氧在线检测仪
2B臭氧分析仪106-L 使用说明书操作手册 2B科技设计的Model 106-L型号臭氧分析仪采用254nm紫外吸收法技术
Model 106 臭氧分析仪手册Rev. D 12目录鉴别记录..............................................................................................3 打印记录................................................................................3 担保申明................................................................................4 警告......................................................................................6 臭氧分析仪引言.......................................................................7 技术规格................................................................................9 操作......................................................................................9 菜单.....................................................................................12 维护/故障诊断........................................................................20 校准.....................................................................................22 部件表..................................................................................28 服务记录...............................................................................28 附录A ：USB 安装...................................................................29 附录B ：使用USB 连接. (32)深圳市深国安电子科技有限公司地址：广东省深圳市龙华新区牛栏前大厦Ａ１５０９网址：ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ．ｃｎ ｗｗｗ．ｓｈｅｎｇｕｏａｎ．ｃｏｍ蒋小姐：１３４ ２８７６ ２６３１ 电话：８６ ７５５－８５２５８９００3鉴别记录请记录下列信息用做将来参考：产品序列号：____________________________________ 质保日期： ____________________________________（自收货之日起有效）打印记录新版本是仪器操作指南的完整修订本，合并了先前所有该仪器的更新彩页及补充说明。
虚仪科技 VIRTINS Multi-Instrument (万用仪) 3.2 说明书
虚仪科技
Virtins Technology
VIRTINS Multi-Instrument (万用仪) 3.2 使用说明书
本说明书适用于 VIRTINS Multi－Instrument（万用仪）。它包括： VIRTINS 示波器 VIRTINS 频谱分析仪 VIRTINS 信号发生器 VIRTINS 万用表 VIRTINS 数据记录仪 VIRTINS 频谱 3D 图 VIRTINS 设备检测计划 VIRTINS LCR 表 VIRTINS DDP 查看器 的使用说明。如果您仅购买了其中的某些仪器，则仅相应章节适用。
注意： 虚仪科技保留在任何时候无需预先通知而对本使用说明书进行修改的权利。 本使用说明书 可能包含有文字错误。
1
版权所有 © 2009 虚仪科技
VIRTINS Multi-Instrument(万用仪)3.2 使用说明书
虚仪科技
Virtins Technology
目录
1 引言 ....................................................................................................................................................12 1.1 概述 ............................................................................................................................................12 1.2 系统要求 .............................
Agilent 电源供电系统操作手册说明书
ErrataTitle & Document Type: 6212B/6214B/6216B/6218B DC Power Supply Operating and Service ManualManual Part Number: 5950-1928Revision Date: November 1982About this ManualWe’ve added this manual to the Agilent website in an effort to help you support your product. This manual provides the best information we could find. It may be incompleteor contain dated information, and the scan quality may not be ideal. If we find a bettercopy in the future, we will add it to the Agilent website.HP References in this ManualThis manual may contain references to HP or Hewlett-Packard. Please note that Hewlett- Packard's former test and measurement, life sciences, and chemical analysisbusinesses are now part of Agilent Technologies. The HP XXXX referred to in this document is now the Agilent XXXX. For example, model number HP8648A is now model number Agilent 8648A. We have made no changes to this manual copy.Support for Your ProductAgilent no longer sells or supports this product. You will find any other availableproduct information on the Agilent Test & Measurement website:Search for the model number of this product, and the resulting product page will guideyou to any available information. Our service centers may be able to perform calibrationif no repair parts are needed, but no other support from Agilent is available.。
VOC报警器
VOC报警器VOC报警器产品描述：VOC检测报警器是东日瀛能科技多年来技术积累的杰作,拥有自主知识产权的高精度检测设备,同时、通过国家的防爆电气产品质量监督检验中心和质量技术监督局颁发的相关检测证书,通书为迎合国际市场,通过了CE ROHS CCC的国际认证.该系统产品适用于各种环境和特殊环境中的挥发性有机物VOC浓度和泄露，在线检测及现场声光报警，对危险现场的作业安全起到了预警作用，此仪器采用进口的电化学传感器和微控制器技术，具有信号稳定，精度高，重复性好等优点，防爆接线方式适用于各种危险场所，并兼容各种控制器，PLC,DCS等控制系统，可以同时实现现场报警和远程监控，报警功能，4-20mA标准信号输出，继电器开关量输出。
VOC报警器产品特性：进口电化学传感器具有良好的抗干扰性能，适用寿命8年。
采用先进微处理技术，响应速度快，测量精度高，稳定性和重复性好。
检测现场具有具有现场声光报警功能，气体浓度超标即时报警，是危险场所作业的安全保障。
4现场带背光大屏幕LCD显示，直观显示气体浓度，类型，单位，工作状态等。
5独立气室，更换传感器无须现场标定，传感器关键参数自动识别。
6全量程范围温度数字自动跟踪补偿，保证测量准确性。
检测气体：空气中的VOC检测范围：0~100ppm,0~200ppm,0~1000ppm,0~1000ppm,0~5000ppm,100%LEL可选。
分别率：0.01ppm(0~100ppm);0.1ppm(0~1000ppm);1ppm(0~10000ppm以上)；0.1LEL.工作方式：固定式连续工作，扩散式，管道式，流通时，泵吸式可选。
检测误差：≦1%（F.S）响应时间：≦10S输出信号：电流信号输出4-20MA报警方式：2路无源节点信号输出，报警点可设置。
工作环境：-20℃~50℃(特殊要求：（-40℃~+70℃)相对湿度：≦90%RH工作电压：DC12~30V传感器寿命：3年防爆形式：探头变送器及传感器均为隔爆型。
臭氧发生器说明书
臭氧发生器说明书Ozone Generator Specification适用于CF-G-3-(5-45)KG系列有限公司济南市臭氧应用工程技术研究中心臭氧发生器操作手册前言前言本臭氧发生器手册中包含了重要的安全注意事项、操作说明，是整个臭氧设备操作手册中不可缺少的组成部分。
操作人员在运行系统前必须仔细阅读本手册中的全部内容。
本操作手册（后面简称手册）中包含了所有与 CF-G-3- 型号臭氧发生器相关的详细信息，以便使用者在各个环节都能安全的操作和维护臭氧发生器设备。
手册将从下列环节进行论述：1.安装/固定，调试2.运行3.故障检修/维修4.运输，储存；报废，拆除/处臵本臭氧发生器的操作手册的保存：1.放臵在离车间最近的便利位臵2.交给该车间的负责人员3.妥善保存直到该设备被弃用必须保证操作人员能随时取阅本操作手册手册组成：本操作手册的附录中包含了用于维护、故障检修及维修的额外信息，如：警报列表电路图数据记录表。
臭氧发生器操作手册目录目录1产品说明 (4)1.1概况 (4)1.2技术数据 (4)2 安全措施和规范 (7)2.1 警示标识信息 (7)2.2 安全规范原则 (8)2.3 安全措施及注意事项 (9)2.4 安全设备和监测设备 (10)2.5 组织人员 (10)2.6 相关联危险 (10)2.7 其它危险 (13)2.8 紧急应对措施 (14)2.9 指南，标准和规范 (14)3安装调试 (15)3.1 安装前准备 (15)3.2 安装 (15)3.3 调试前检查 (16)3.4 电气线路接线 (17)3.5臭氧放电室臭氧出气管道连接 (17)4臭氧发生器工作原理 (18)4.1臭氧 (18)4.2臭氧发生器工作原理 (18)4.3 应用领域 (19)4.4 使用前重要说明 (19)5系统运行 (21)5.1开机前准备 (21)4.2 开机步骤 (21)4.3 系统开关机 (21)4.4.控制面板操作说明 (22)6 技术支持与售后服务 (27)6.1 售后技术支持服务 (27)6.2 维护 (27)7 免责声明 (29)1产品说明1.1概况臭氧发生装臵是用于制取臭氧气体（O3）的装臵。
FSP3 FSP7 FSP13 FSP30 FSP40指示书说明书
S p e c i f i c a t i o nsSpectrum Analyzer ¸FSPSpecificationsSpecificationsSpecifications are valid under the following conditions:15 minutes warm-up time at ambient temperature, specified environmental conditions met, calibration cycle adhered to, and total calibration performed.Data without tolerances: typical values only.Data designated "nominal" applies to design parameters and is not tested.Data designated "σ = xx dB" is shown as standard deviation.¸FSP3¸FSP7¸FSP13¸FSP30¸FSP40 FrequencyFrequency range9 kHz to 3GHz9 kHz to 7GHz9 kHz to 13.6GHz9 kHz to 30GHz9 kHz to 40GHz Frequency resolution0.01 HzInternal reference frequency (nominal)Aging per year1)1)After 30 days of operation.1 × 10–6Temperature drift 1 × 10–6With option ¸FSP-B4 (OCXO)Aging per year1) 1 × 10–7Temperature drift 1 × 10–8External reference frequency10 MHzFrequency display with marker or frequency counterMarker resolution span/500Max. deviation(sweep time >3× auto sweep time)±(frequency × reference frequency + 0.5% × span + 10% × resolution bandwidth + ½ (last digit)) Frequency counter resolution0.1 Hz to 10 kHz (selectable)Count accuracy (S/N >25 dB)±(frequency × reference frequency + ½ (last digit))Frequency span0 Hz,10 Hz to 3GHz0 Hz,10 Hz to 7GHz0 Hz,10 Hz to 13.6GHz0 Hz,10 Hz to 30GHz0 Hz,10 Hz to 40GHzMax. span deviation0.1% Spectral purity (dBc (1 Hz)) SSB phase noise, f = 500 MHz, for f > 500 MHz see diagrams belowCarrier offset100 Hz<–84, typ.–90 1 kHz<−100, typ.−108 10 kHz<−106, typ. −113100 kHz2)2)Valid for span >100 kHz.<−110, typ. −1131 MHz2)<−120, typ.−125 10 MHz typ.−145 Residual FMf = 500 MHz, RBW 1 kHz,sweep time 100 mstyp. 3 Hz2 Spectrum Analyzer ¸FSPSpectrum Analyzer ¸FSP3Sweep timeSpan ≥10 Hz 2.5 ms to 16000 sMax. deviation1%Span 0 Hz 1 µs to 16000 sResolution125 nsResolution bandwidthsBandwidths10 Hz to 10 MHz (–3 dB) in 1, 3 sequenceEMI bandwidths200 Hz, 9 kHz, 120 kHz (–6 dB)Bandwidth accuracy≤100 kHz<3%300 kHz to 3 MHz<10%10 MHz+10%, –30%Shape factor –60 dB: –3 dB≤100 kHz<5:1 (Gaussian filters)300 kHz to 3 MHz<15:1 (4-pole synchronously tuned filters)10 MHz<7:1Shape factor –60 dB: –6 dBEMI bandwidths<5:1Video bandwidths 1 Hz to 10 MHz in 1, 3 sequenceFFT filterBandwidths 1 Hz to 30 kHz (–3 dB) in 1, 3 sequenceBandwidth accuracy5%, nominalShape factor –60dB:–3 dB 2.5:1 nominalChannel filterBandwidths100; 200; 300; 500 Hz;1; 1.5; 2; 2.4; 2.7; 3; 3.4; 4; 4.5; 5; 6; 8.5; 9; 10; 12.5; 14; 15; 16; 18 (RRC); 20; 21; 24.3 (RRC); 25; 30; 50; 100;150; 192; 200; 300; 500 kHz; 1;1.228; 1.5; 2; 3; 5 MHz1.28 (RRC), 3.84 (RRC), 4.096 (RRC)LevelDisplay range displayed average noise level to 30 dBmMaximum input levelDC voltage50 V0 VRF attenuation 0 dBCW RF power20 dBmPulse spectral density97 dBµV (1 MHz)RF attenuation ≥10 dBCW RF power30 dBmMax. pulse voltage150 V50 VMax. pulse energy (10 µs) 1 mWs0.5 mWs1 dB compression of input mixer0 dB RF attenuation, f > 200 MHz0 dBm nominalIntermodulation3rd-order intermodulationIntermodulation-free dynamic range, level 2 × –30 dBm, ∆f > 5 × RBW or 10 kHz, whichever is larger20 MHz to 200 MHz>70 dBc, TOI >5 dBm200 MHz to 3 GHz>74 dBc, TOI >7 dBm (typ. 10 dBm)3 GHz to 7 GHz−>80 dBc, TOI >10 dBm (typ. 15 dBm)7 GHz to 13.6 GHz−−>80 dBc, TOI >10 dBm13.6 GHz to 30 GHz−−−>76 dBc, TOI >8dBm>80 dBc, TOI >10 dBm 30 GHz to 40 GHz−−−−>80 dBc, TOI >10 dBm With optional Electronic Attenuator ¸FSP-B25 switched on20 MHz to 200 MHz>74 dBc, TOI > 7 dBm−200 MHz to 3 GHz>80 dBc, TOI > 10 dBm−3 GHz to 7 GHz>84 dBc, TOI > 12 dBm−4 Spectrum Analyzer ¸FSPSecond harmonic intercept point (SHI)<100 MHz typ. 25 dBm100 MHz to 1.5 GHz typ. 35 dBm1.5 GHz to 7 GHz−typ. 80 dBm7 GHz to 13.6 GHz−−typ. 80 dBm13.6 GHz to 30 GHz−−−typ. 80 dBm30 GHz to 40 GHz−−−−typ.80 dBm Displayed average noise level(0 dB RF attenuation, RBW 10 Hz, VBW 1 Hz, 20 averages, trace average, span 0 Hz, termination 50 Ω)Frequency9 kHz<−95 dBm100 kHz<−100 dBm1 MHz<−120 dBm, typ. −125 dBm10 MHz to 1 GHz<−142 dBm,typ.−145 dBm<−140 dBm, typ. −145 dBm1 GHz to 3 GHz<−140 dBm,typ. −145 dBm<−138 dBm, typ. −143 dBm3 GHz to 7 GHz−<−138 dBm,typ. −143 dBm<−135 dBm, typ. −140 dBm7 GHz to 13.6 GHz−−<−132 dBm, typ. −138 dBm13.6 GHz to 22 GHz−−−<−120 dBm,typ. −128 dBm−22 GHz to 30 GHz−−−<−115 dBm,typ. −123 dBm−13.6 GHz to 20 GHz−−−−<−120 dBm,typ. −128 dBm 20 GHz to 30 GHz−−−−<−120 dBm,typ. −128 dBm 30 GHz to 40 GHz−−−−<−112 dBm,typ. −120 dBm Displayed average noise level with preamplifier on (option ¸FSP-B25)10 MHz to 2 GHz<–152 dBm−2 GHz to 7 GHz<–150 dBm−Immunity to interferenceImage frequency>70 dBIntermediate frequency (f <3 GHz)>70 dBSpurious responses (f >1 MHz, withoutinput signal, 0 dB attenuation)<−103 dBmOther spurious (with input signal, mixer level <–10 dBm, ∆f >100kHz)f <7 GHz: <−70 dBc f <13.6 GHz: <−64 dBc f <30 GHz: <−56 dBcLevel displayScreen501 × 400 pixels (one diagram), max. two diagrams with independent settingsLogarithmic level scale10 dB to 200 dB, in steps of 10 dBLinear level scale10% of reference level per level division (10 divisions)Traces max. 3, with two diagrams on screen max. 3 per diagramTrace detector max peak, min peak, auto peak, sample, quasi-peak, average, RMSTrace functions clear/write, max. hold, min hold, averageNumber of test points501, selectable in steps of approx. factor 2, 125 to 8001Setting range of reference levelLogarithmic level display–130 dBm to 30 dBm, in steps of 0.1 dBLinear level display70.71 nV to 7.07 V in steps of 1%Units of level scale dBm, dBmV, dBµV, dBµA, dBpW (log level display), mV, µV, mA, µA, pW, nW (linear level display)Max. uncertainty of level measurementAt 128 MHz, −30 dBm (RF attenuation10dB, RBW 10kHz, ref. level –20 dBm)<0.2 dB (σ = 0.07 dB)Spectrum Analyzer ¸FSP5Frequency response<50 kHz <+0.5/− 1.0 dB50 kHz to 3 GHz<0.5 dB (σ = 0.17 dB)3 GHz to 7 GHz–<2 dB(σ = 0.7 dB)7 GHz to 13.6 GHz––<2.5 dB1)13.6 GHz to 30 GHz–––<3 dB1)30 GHz to 40 GHz––––<4 dB1) Frequency response with option ¸FSP-B25 switched on (preamplifier, electronic attenuator)10 MHz to 3 GHz<1 dB(σ = 0.33 dB)–3 GHz to 7 GHz–<2 dB(σ = 0.7 dB)–Attenuator<0.2 dB (σ = 0.07 dB)Reference level switching<0.2 dB (σ = 0.07 dB)Display nonlinearity LOG/LIN (S/N >16 dB)RBW ≤100 kHz0 dB to –70 dB<0.2 dB (σ = 0.07 dB)–70 dB to –90 dB<0.5 dB (σ = 0.17 dB)RBW ≥300 kHz0 dB to –50 dB<0.2 dB (σ = 0.07 dB)–50 dB to –70 dB<0.5 dB (σ = 0.17 dB)Bandwidth switching uncertainty (ref. to RBW = 10 kHz)10 Hz to 100 kHz <0.1 dB (σ = 0.03 dB)300 kHz to 10 MHz<0.2 dB (σ = 0.07 dB)1 Hz to 3 kHz, FFT<0.2 dB (σ = 0.03 dB)Total measurement uncertainty0 GHz to 3 GHz0.5 dBTrigger functionsTriggerSpan ≥10 HzTrigger source free run, video, external, IF levelTrigger offset125 ns to 100 s, resolution 125 ns min. (or 1% of offset)Span = 0 HzTrigger source free run, video, external, IF levelTrigger offset±125 ns to 100 s, min. resolution 125 ns, dependent on sweep timeMax. deviation of trigger offset±(125 ns + (0.1% × delay time))Gated sweepTrigger source external, IF level, videoGate delay 1 µs to 100 sGate length125 ns to 100 s, min. resolution 125 ns or 1% of gate lengthMax. deviation of gate length±(125 ns + (0.05% × gate length))Inputs and outputs (front panel)RF input N female, 50 Ωtest port system 50 Ω,N female,3.5 mm female2)test port system 50 Ω,N female,K female2)VSWR (RF attenuation >0 dB)f <3 GHz 1.5:1f <7 GHz− 2.0:1f <13 GHz−− 2.5:1f <30 GHz−−− 3.0:1f <40 GHz−−−− 3.0:1 Input attenuator0 dB to 70 dB in 10 dB stepsWith option ¸FSP-B250 dB to 75 dB in 5 dB steps not availableProbe power supply+15 V DC, –12.6 V DC and ground, max. 150 mAKeyboard connector PS/2 female for MF2 keyboardAF output (only with option ¸FSP-B3) 3.5 mm mini-jackOutput impedance10 ΩOpen-circuit voltage up to 1.5 V, adjustable6 Spectrum Analyzer ¸FSPInputs and outputs (rear panel)IF 20.4 MHz Z out= 50 Ω, BNC femaleLevelRBW ≤30 kHz, FFT–10 dBm at reference level, mixer level >–60 dBmRBW ≥100 kHz0 dBm at reference level, mixer level >–60 dBmReference frequencyOutput BNC femaleOutput frequency10 MHzLevel 0 dBm, nominalInput10 MHzRequired level0 dBm into 50 ΩOthersPower supply for noise source BNC female, 0 V and 28 V, switchable, max. 100mAExternal trigger/gate input BNC female, >10 kΩTrigger voltage 1.4 V (TTL)IEC/IEEE bus remote control interface to IEC 625-2 (IEEE 488.2)Command set SCPI 1997.0Connector24-pin Amphenol femaleInterface functions SH1, AH1, T6, L4, SR1, RL1, PP1, DC1, DT1, C0Serial interface RS-232-C (COM), 9-pin sub-D connectorPrinter interface parallel (Centronics-compatible)Mouse connector PS/2 femaleConnector for ext. monitor (VGA)15-pin sub-D connectorGeneral dataDisplay21 cm TFT colour display (8.4”)Resolution640 × 480 pixels (VGA resolution)Pixel failure rate<2 × 10 –5Mass memory 1.44 MByte 3½” disk drive (built-in), hard diskData storage>500 instrument settings and tracesTemperaturesOperating temperature range+5°C to +40°CPermissible temperature range+5°C to +45°CStorage temperature range–40°C to +70°CDamp heat+40°C at 95% relative humidity (EN 60068-2-30)Mechanical resistanceVibration, sinusoidal 5 Hz to 150 Hz, max. 2 g at 55 Hz; 0.5 g from 55 Hz to 150 Hz; meets EN60068-2-6, EN60068-2-30, EN61010-1,MIL-T-28800D, class 5Vibration, random10 Hz to 100 Hz, acceleration 1 g (rms)Shock test40 g shock spectrum, meets MIL-STD-810C and MIL-T-28800D, classes 3 and 5Recommended calibration interval 2 years for operation with external reference,1 year with internal referencePower supplyAC supply100 V AC to 240 V AC, 50 Hz to 400Hz, 3.1 A to 1.3 A, class of protection I to VDE411Typical power consumption70 VA 120 VA150 VASafety meets EN61010-1, UL3111-1, CSAC22.2 No. 1010-1,RFI suppression meets EMC Directive of EU (89/336/EEC) and German EMC lawTest mark VDE, GS, CSA, CSA-NRTL/CDimensions in mm (W × H × D)412 × 197 × 417Weight10.5 kg11.3 kg12 kg1)RF attenuation 10 dB, sweep time >1s/1 GHz.2)See recommended extras for alternate connectors.Spectrum Analyzer ¸FSP7Specifications of optionsTracking Generator ¸FSP-B9Unless specified otherwise, specifications not valid for frequency range from –3 × RBW to +3 × RBW; however, at least not valid from –9 kHz to +9 kHz.The specified level accuracy of the tracking generator is valid under the following conditions: RF attenuation ≥ 20 dB and sweep time ≥2000 ms.FrequencyFrequency range9 kHz to 3 GHzFrequency offsetSetting range±150 MHzResolution 1 HzSpectral purity (dBc (1 Hz)) SSB phase noise, f = 500 MHz, carrier offset 100 kHzNormal mode typ. –90With FM modulation on typ. –70LevelLevel setting range–30 dBm to 0 dBm in steps of 0.1 dBLevel setting range with AM–30 dBm to –6 dBm in steps of 0.1 dBMax. deviation of output level, 128 MHz, 0 dBm<1 dBFrequency responseOutput level 0 dBm, 100 kHz to 2 GHz<1 dBOutput level 0 dBm to −25 dBm, 9 kHz to 3 GHz<3 dBDynamic rangeAttenuation measurement range, RBW = 1 kHz, f > 10 MHz120 dBSpuriousHarmonics, output level –10 dBm typ. –30 dBcNonharmonics, output level 0 dBm typ. –30 dBcModulationModulation format (external)I/Q, AM, FM, FM-DC, PM, ASK, FSKAM, f > 10 MHzModulation depth0% to 99%Modulation frequency range0 Hz to 1 MHzFM, f > 10 MHzFrequency deviation0 Hz to 20 MHzModulation frequency range0 Hz to 100 kHzI/Q modulation, f > 10 MHz0 Hz to 30 MHz typ. 1 dBInputs and outputs (front panel)RF output N female, 50 ΩVSWR typ. 2:1Inputs and outputs (rear panel)TG/AM IN V max(pp) = 1 V; Z in = 50 Ω, BNC femaleTG Q/FM IN V max(pp) = 1 V; Z in = 50 Ω, BNC femaleExternal Generator Control ¸FSP-B10Supported signal generators¸SME02/03/06, ¸SMG, ¸SMGL, ¸SMGU, ¸SMH, ¸SMHU,¸SMIQ02B/02E/03B/03E/04B/06B¸SML, ¸SMR20/27/30/40/60¸SMP02/22/03/04,¸SMX, ¸SMY¸SMT02/03/06LAN Interface ¸FSP-B16Connector (rear panel)RJ-45Supported protocols10Base-T (IEEE standard 10 Mbit/s 802.3)100Base-TX (IEEE standard 100 Mbit/s 802.3u)Extended Environmental Specification ¸FSP-B20Temperature range (noncondensing)Operating temperature range 0°C to +50°CPermissible temperature range0°C to +55°CMechanical resistanceVibration, random10 Hz to 300 Hz, acceleration 1.9 g (rms)8 Spectrum Analyzer ¸FSPLO/IF ports for external Mixers ¸FSP-B21 (¸FSP40 only)LO levelFrequency range 7 GHz to 13.2 GHzLevel+15.5 dBm ±3 dBIF inputIF frequency 404.4 MHzFull scale level2 port mixer, LO output/IF input (front) –20 dBmLevel deviation<1dBIF level –30 dBm, reference level –20 dBm, RBW 30 kHz,LO output/IF input (front)Full scale level3 port mixer, IF input (front) –20 dBmLevel deviationIF level –30 dBm, reference level –20 dBm, RBW 30 kHz, IF input (front)<1dBInputs and outputs (front)LO output/IF input SMA female, 50 ΩIF input SMA female, 50 ΩElectronic Attenuator ¸FSP-B25 (only for ¸FSP3 and ¸FSP7)FrequencyFrequency range10 MHz to 7 GHzInput attenuator range (mechanical)0 dB to 75 dB in 5 dB stepsElectronic attenuation range0 dB to 30 dB in 5 dB stepsPreamplifier20 dB, switchableDisplayed average noise level with preamplifier on (0 dB RF attenuation, RBW 10 Hz, VBW 1 Hz, 20 averages, trace average, span 0 Hz, termination 50 Ω) 10 MHz to 2 GHz<–152 dBm2 GHz to 7 GHz<–150 dBmIntermodulation with electronic attenuator on3rd-order intermodulation, intermodulation-free dynamic range, level 2 × –30 dBm, ∆f >5 × RBW or 10 kHz, whichever is larger20 MHz to 200 MHz>74 dBc, TOI >7 dBm200 MHz to 3 GHz>80 dBc, TOI >10 dBm3 GHz to 7 GHz>84 dBc, TOI >12 dBmMax. deviation of level measurement<0.2 dB (σ = 0.07 dB)128 MHz, –30 dBm (RF attenuation 10 dB, RBW 10 kHz,ref. level –20dBm), preamplifier onElectronic attenuator<0.2 dB (σ = 0.07 dB)Frequency response with preamplifier, electronic attenuator10 MHz to 3 GHz<1.0 dB (σ = 0.33 dB)3 GHz to 7 GHz<2 dB (σ = 0.7 dB)Trigger Port ¸FSP-B28Output voltage high ≤1.4 Vlow ≥0.7 VTrigger port connector25-pin sub-D femaleFrequency range extension 20 Hz ¸FSP-B29Frequency range 20 Hz to f maxFrequency response <9 kHz <1 dBDisplayed average noise level0 dB RF attenuation, RBW 10 Hz, VBW 1 Hz, 20 averages, trace average, span 0 Hz, termination50Ω20 Hz<–58 dBm100 Hz<–75 dBm1 kHz<–85 dBmDC Power Supply ¸FSP-B30Input voltage range10 V to 28 V DC25 A to 12.5 AOutput voltage 120 V to 360 V DC/300 WCurrent consumption (V DC = 12 V, ¸FSP without options, default settings)¸FSP3typ. 6 A¸FSP30typ. 8 AOperating temperature range 0°C to +50°CStorage temperature range–40°C to +70°CDimensions in mm (W × H × D)145 × 154 × 65Weight0.6 kgSpectrum Analyzer ¸FSP9Battery Pack ¸FSP-B31/-B32NiMH battery pack with built-in load control for all ¸FSP and ¸ESPI models with options ¸FSP-B1 and ¸FSP-B30Input voltage of battery pack10 V to 28 V DCInput voltage power supply (battery charge)24 V DC/max. 3 AOutput voltageBattery operation13.2 V DC/200 WhBypass operation10 V to 28 V DC/10 ATypical operating times (¸FSP without options)¸FSP3 2 h¸FSP30 1.5 hCharging time 5 h at 25°COperating temperature range (discharging)0°C to +50°COperating temperature range (charging)+10°C to +40°CStorage temperature range (<1 year)–20°C to +35°CStorage temperature range (<1 month)–20°C to +55°CDimensions (W × H × D)400 mm × 134 mm × 42 mmWeight 3.7 kgAC adapter (¸FSP-B31 only)Input voltage range100 V to 240 V AC ±10%Input frequency range50 Hz to 60 Hz ±5%Input power140 VAOutput voltage24 VOutput current 3 AOperating temperature range 0°C to +50°CStorage temperature range –20°C to +70°CDimensions (W × H × D)132 mm × 58 mm × 30 mmWeight0.3 kgOrdering informationOrder designation Type Order No. Spectrum Analyzer, 9 kHz to 3 GHz¸FSP31164.4391.03 Spectrum Analyzer, 9 kHz to 7 GHz¸FSP71164.4391.07 Spectrum Analyzer, 9 kHz to 13.6 GHz¸FSP131164.4391.13 Spectrum Analyzer, 9 kHz to 30 GHz¸FSP301164.4391.30 Spectrum Analyzer, 9 kHz to 40 GHz¸FSP401164.4391.40 Accessories suppliedPower cable, compact manual, CD-ROM with operating manual and service manual.¸FSP30: test port adapter with 3.5 mm female (1021.0512.00) and N female (1021.0535.00) connector.¸FSP40: test port adapter with K female (1036.4770.00) and N female (1036.4777.00) connector.OptionsOrder designation Type Order No.Retrofittable RemarksOptionsDelete Manuals¸FSP-B01129.8394.02Rugged Case, carrying handle (factory-fitted)¸FSP-B11129.7998.02noAM/FM Audio Demodulator¸FSP-B31129.6491.02yes not with ¸FSP-B15. OCXO Reference Frequency ¸FSP-B41129.6740.02yesTV Trigger/RF Power Trigger¸FSP-B61129.859.4.02yes not with ¸FSP-B21. Internal Tracking Generator 9 kHz to 3GHz, I/Q modulator, for all ¸FSP models¸FSP-B91129.6991.02yesExternal Generator Control for all ¸FSP models¸FSP-B101129.7246.02yesPulse Calibrator for ¸FSP¸FSP-B151155.1006.02yes not with ¸FSP-B3;required for ¸FS-K72/-K73 LAN Interface 100BT for all ¸FSP models with Windows XP (1164.4391.xx)¸FSP-B161129.8042.03yes10 Spectrum Analyzer ¸FSPOrder designation Type Order No.Retrofittable RemarksLAN Interface 100BT for all ¸FSP models with Windows NT (1043.4495.xx)¸FSP-B161129.8042.02yesExtended Environmental Specification ¸FSP-B201155.1606.06noLO/IF Ports for External Mixers¸FSU-B211157.1090.02yes not with ¸FSP-B6;only for ¸FSP40¸FSP-B251129.7746.02yesElectronic Attenuator, 0 dB to 30 dB, 5 dB steps, integrated preamplifier for¸FSP3 and ¸FSP7Trigger Port for ¸FSP for indication of trigger conditions¸FSP-B281162.9915.02yesFrequency Range Extension 20 Hz for ¸FSP3/7¸FSP-B291163.0663.07noFrequency Range Extension 20 Hz for ¸FSP13/30¸FSP-B291163.0663.30noFrequency Range Extension 20 Hz for ¸FSP40¸FSP-B291163.0663.40noDC Power Supply for Spectrum Analyzers ¸FSP¸FSP-B301155.1158.02yesBattery Pack for Spectrum Analyzers ¸FSP¸FSP-B311155.1258.02yes¸FSP-B1 and¸FSP-B30 required Spare Battery Pack for Spectrum Analyzers ¸FSP¸FSP-B321155.1506.02yes¸FSP-B31 required Demodulation Hardware and Memory Extension¸FSP-B701157.0559.02yes required for ¸FS-K72/-K73; ¸FSP-B15 required SoftwarePhase Noise Measurement Software¸FS-K41108.0088.02GSM/EDGE Application Firmware, Mobile¸FS-K51141.1496.02AM/FM/ϕM Measurement Demodulator¸FS-K71141.1796.02Application Firmware for Bluetooth® Measurements¸FS-K81157.2568.02Power Sensor Measurements¸FS-K91157.3006.02supports ¸NRP-Z11/-Z21with ¸NRP-Z4 USB con-nectorApplication Firmware for Noise Figure and Gain Measurements¸FS-K301300.6508.02Preamplifier ¸FSP-B25recommended3GPP BTS/Node B FDD Application Firmware¸FS-K721154.7000.02¸FSP-B15 and -B70required3GPP UE FDD Application Firmware¸FS-K731154.7252.02¸FSP-B15 required,¸FSP-B70 recommended 3GPP HSDPA BTS Application Firmware¸FS-K741300.7156.02¸FS-K72 required3GPP TD-SCDMA BTS Application Firmware¸FS-K761300.7291.023GPP TD-SCDMA UE Application Firmware¸FS-K771300.8100.02CDMA2000® (IS-95) 1xEV-DV BTS FDD Application Firmware¸FS-K821157.2316.02CDMA2000® 1xEV-DV MS Application Firmware¸FS-K831157.2416.02CDMA2000® 1xEV-DO BTS Application Firmware¸FS-K841157.2851.02CDMA2000®-1xEV-DO MS Application Firmware¸FS-K851300.6689.02WLAN 802.11a TX Measurements Application Firmware¸FSP-K901300.6650.02The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Rohde&Schwarz is under license.CDMA2000® is a registered trademark of the Telecommunications Industry Association (TIA -USA).Spectrum Analyzer ¸FSP11Europe:Tel:+491805124242,e-mail:*********************************.com·USA:Tel.+1410-910-7988,e-mail:*********************************.comAsia:Tel.+6568463710,e-mail:***********************************.com¸i s a r e g i s t e r e d t r a d e m a r k o f R o h d e &S c h w a r z G m b H &C o . K G · T r a d e n a m e s a r e t r a d e m a r k s o f t h e o w n e r s · P r i n t e d i n G e r m a n y (B i a s )P D 0758.1206.22 · S p e c t r u m A n a l y z e r ¸F S P · V e r s i o n 05.00 · O c t o b e r 2004 · D a t a w i t h o u t t o l e r a n c e l i m i t s i s n o t b i n d i n g · S u b j e c t t o c h a n g eCertified Quality System ISO 9001Certified Environmental SystemISO 14001Product brochure see PD 0758.1206.12 and at (search term: FSP)Recommended extrasDesignationTypeOrder No.Headphones 0708.9010.00US Keyboard with Trackball ¸PSP-Z21091.4100.02PS/2 Mouse¸FSE-Z21084.7043.02DC Block,10kHz to 18GHz (type N)¸FSE-Z41084.7443.02Colour Monitor, 15", 230 V ¸PMC31082.6004.02IEC/IEEE Bus Cable, 1 m ¸PCK 0292.2013.10IEC/IEEE Bus Cable, 2 m ¸PCK 0292.2013.2019" Rack Adapter (not for ¸FSP-B1)¸ZZA4781096.3248.00Soft Carrying Case, grey¸ZZT4731109.5048.00Printed operating manual (German)–1093.4820.11Printed operating manual (English)–1093.4820.12Printed service manual (German)–1093.4820.81Printed service manual (English)–1093.4820.82Matching Pads, 75 ΩL Section¸RAM 0358.5414.02Series Resistor, 25 Ω1)1)Taken into account in device function RF INPUT 75 Ω.¸RAZ 0358.5714.02SWR Bridge, 5 MHz to 3 GHz ¸ZRB2 0373.9017.52SWR Bridge, 40 kHz to 4 GHz ¸ZRC 1039.9492.52High-Power Attenuators, 100 W 3/6/10/20/30 dB¸RBU1001073.8495.XX (XX=03/06/10/20/30)High-Power Attenuators, 50 W 3/6/10/20/30 dB ¸RBU501073.8695.XX (XX=03/06/10/20/30)For ¸FSP30Test Port Adapter, 3.5 mm male –1021.0529.00Test Port Adapter, N male–1021.0541.00Microwave Measurement Cable and Adapter Set ¸FS-Z151046.2002.02For ¸FSP40Test Port Adapter K male –1036.4802.00Test Port Adapter N male –1036.4783.00Test Port Adapter 2.4 mm female¸FSE-Z51088.1627.02Related data sheetsTitleOrder No.TV Trigger/RF Power Trigger ¸FSP-B6PD 0757.6433Noise Measurement Software ¸FS-K3 for Spectrum Analyzers ¸FSE, ¸FSIQ and ¸FSP PD 0757.2380Phase Noise Measurement Software ¸FSE-K4PD 0757.6727GSM/EDGE Application Firmware ¸FS-K5 for ¸FSP PD 0757.6185FM Measurement Demodulator ¸FS-K7 PD 0757.6685Bluetooth Application Firmware ¸FS-K8PD 0757.7730Application Firmware for Noise Figure and Amplifier Measure-ments R&S®FS-K30PD 0758.0839.32WCDMA 3GPP Application Firmware ¸FS-K72/-K73/-K74 PD 0757.7246TD-SCDMA Test Application Firmware ¸FS-K76/-K77 PD 0758.0880.32CDMA2000® Base Station Test Application Firmware 1xEV-DO Base Station Test Application Firmware ¸FS-K82/-K84PD 0758.1712.32Mobile Station Test Application Firmware ¸FS-K83/¸FS-K85PD 0758.1729.32WLAN Application Firmwar e ¸FSQ-K91/ ¸FSP-K90PD 0758.1435.12。
Agilent 8453 UV-visible 光谱仪说明书
Agilent 8453 UV-visible spectrophotometer Our measure is your success.products | applications | software | servicesfor chemical analysisAgilent 8453 optics Tungsten lamp Deuterium lamp LensShutterLensSlitGrating1024-element diode array2Agilent’s UV-visible systemsUV-visible spectroscopy solutions that satisfy the diverse needs of analystsin routine QA/QC, research, and method development laboratories.The diode-array advantagesBacked by over two decades ofexperience in the development andmanufacture of diode-array spectro-photometers, the Agilent 8453 givesyou clear advantages.•Fast spectral scanning for completespectral information useful for:-proof of identity and pureness ofthe sample-additional information for “out ofspecification test result” investigationin a regulated environment-re-evaluation with different method-multi-wavelength applications suchas user-defined equations-multicomponent analysis of mixtures•Open sample area for convenientsample handling•High throughput optics guaranteesexcellent signal-to-noise for highsensitivity•Virtually absolute wavelengthresettability allows selection ofoptimum wavelength and use ofelectronic standards•Exceptional ruggedness and reliabilityThe Agilent 8453 UV-visiblespectrophotometer offers the latestin diode-array technology:•Small footprint to save bench space•Prealigned deuterium and tungstenlamp light sources for trouble-freemaintenance•Built-in buttons to measure sample,standard, and blank for convenientmeasurements even when wearinggloves•Thermally stable ceramic spectrographfor a wide operating temperature range•Communication through GPIB or LANfor dedicated or networked PC control•Firmware upgrade from PC for easyparticipation in future developments•Built-in GPIO interface for control ofaccessories•Compliance with all requirements ofthe European Pharmacopoeia (EP) andUnited States Pharmacopeia (USP)Optical performanceThe Agilent 8453 offers the advantagesof a diode array plus significantimprovements in optical performance:•190 – 1100 nm wavelength range•1 nm slit width•< 0.03 % stray lightGood Laboratory PracticeThe Agilent 8453 supports compliancewith GLP regulations:•Serial and firmware revision numberheld in firmware•Own clock for time and date stampsof the spectra•Extensive self-test procedures thatcheck the electronics and key opticalcharacteristics to ensure consistentperformance between validation•Built-in electronic logbooks, whichcontain the results of self-tests,notes in instrument maintenance,events and errorsSipper operation is easy with built-inmeasurement buttonsSide door for easy lamp changeOpen sample area means large accessories areeasy to use – here the Peltier cell holder3Specifications – Agilent 8453 UV-Visible spectrophotometerSpectrum of a 0.02 % v/v solution of toluenein hexaneOptical performance Wavelength range 190–1100 nm Slit width 1 nm EP resolution test > 1.6toluene in hexane, ratio abs. at 269 nm/266 nm Stray light< 0.03 %at 340 nm (NaNO 2, ASTM)< 0.05 %at 220 nm (NaI, ASTM)< 1 %at 198 nm (KCl, EP)Wavelength accuracy < ±0.5 nm 0.5-second scan (NIST 2034)< ±0.2 nm at 486.0 and 656.1 nmWavelength reproducibility < ±0.02 nm ten consecutive scans (NIST 2034)Photometric accuracy< ±0.005 A at 440.0, 465.0, 546.1, 590.0, and 635.0 nm, 1 A (NIST 930e)< ±0.01 Aat 235, 257, 313, 350, 430 nm,(potassium dichromate, EP method)Photometric noise < 0.0002 A sixty 0.5 second scans at 0 A, 500 nm, rms Photometric stability< 0.001 A/hat 0 A, 340 nm, after 1-hour warm up, measured over 1 hour, every 5 seconds,constant ambient temp.Baseline flatness < 0.001 A 0.5-second blank, 0.5-second scan, rms Typical scan time 1.5 second full range Shortest scan time 0.1 second full rangeTime until next scan 0.1 secondfull range, 0.1-second scan,up to 150 consecutive scansPhysical dimensions Height x width x depth 185 x 344 x 560 mm (7.3 x 13.5 x 22.0 inches)Weight16.5 kg (36.3 lb)Power requirements Line voltage 90–264 V AC Line frequency 47–63 Hz Power consumption 70 VA typicalEnvironmental conditions Operating temperature 0–50 °C (32–122 °F)Non-operating temperature -40–70 °C (-4–158 °F)Humidity< 95 %, at 25–40 °C (77–104 °F)4Easy to useThe Agilent 8453 UV-visible spectroscopy system may well be the easiest UV-visible system you will ever use. Three steps are all you need to get results:1. Select the task you want2. Enter the parameters and3. Do the mesurementGraphical user interfaceUsability tests performed with actual users in their own labs initiated a completely new approach to user interface design. The Agilent 8453 UV-visible spectroscopy system uses symbolic graphics to:•make the system intuitive, easy to learn, and easy to use,•provide confirmation of current status at a glance,•provide visual confirmation of actions, and•provide fast access to frequently performed activities.AutomationA single dialog box makes setup for automated analyses easy and quick.You can use automation to guide an operator through a series of manual measurements, or combine it with sampling accessories to provide semi- or fully automated analysis. The automation function controls •the Agilent sipper system •the Agilent XY autosampler •the Agilent multicell transport The optional control samples allow you to run an automatic system suitability test before quantitative analyses.Solutions for general purpose tasksEasy to learn and easy to use for increased productivityEnter the parametersDo the measurement2. 3.Select the task you want1.Your results are displayed automaticallyYou mayprint a reportCompatibilityThe Agilent UV-visible ChemStation uses the Microsoft®Windows environment so you can run other programs, such as word processors and spreadsheets, at the same time, and transfer data using copy-and-paste.Clear and simple reports Generating reports could not be easier. Simply click the printer icon in the toolbar and a standard report is printed. When possible this standard report is printed on a single sheet of paper. The report format depends upon the task in use but all reports include essential GLP information such as method and data file name, date, time, operator, overlay of sample spectra and result table.ProductivityThe Agilent 8453 system is a highly productive UV-visible spectroscopy system. Its combination of ease of learning, ease of use, fast spectral acquisition, fast data evaluation, report generation, and automation lets you get results fast – even if you only use the system occasionally.Add diagnostic tools such as performance verification, system documentation, and the extreme reliability of the system and you will spend the minimum time with administration or maintenanceand repair.5Solutions for research and development The power and flexibility to develop the optimum method and solve the toughest problemsPowerful data analysisThe advanced software provides unprecedented interactive and programmable data analysis capability:•21 mathematical functions for processing spectra that you can combine in any sequence •Flexible use of any number of single or multiple wavelengths, or average a range of values•Evaluation using user-entered equations, single-component or multi-component analysis•Up to four different types of data analysis performed on one set of data in parallel•Comparison of data evaluation results using different analysis parameters •Use confirmation analysis with quantitative methods to check the identity and purity of samples, and to detect if measurements are being made outside the linear range of the analysisEnterprise content management Agilent OpenLAB enterprise content manager (ECM) facilitates creation of a knowledge base of UV-visible ChemStation methods and data across larger entities based on web services.Method development toolsFour special utilities are provided toassist the user in developing the bestparameters for quantitative analysis:•Evaluate Standards for linearity –performs a single componentcalibration at each wavelength overa user-specified wavelength. Itdetermines the correlation coefficientand uncertainty at each wavelength.•Compare Calibrations – puts theresults from two independentcalibrations side by side on thescreen for comparison.•Optimize Wavelength for selectivityand accuracy – quantifies a user-selected sample at all wavelengthsand plots the quantification resultsagainst wavelength.•Test Method for precision – calculatesthe average and standard deviation ofmultiple analyses of an identicalsample.Multicomponent analysisMulticomponent UV-visible analysiscan provide a real alternative totime-consuming separations. Fastelectronic scanning, spectral curvefitting of standards to unknowns,excellent wavelength reproducibility,and maximum-likelihood statistics makesure that results are superior to thoseobtained with conventional mechanical-scanning spectrophotometers.Calibration is simple and fast usingpure standards or mixtures of standards.Statistics for the fit of the standardsto the sample spectra give youconfidence in your results.CustomizationVirtually every aspect of the systemcan be customized through macroprogramming.A series of predefined reports areavailable in the software. However,to fulfill specific needs, the user candefine their own customized reportsbased on the predefined reports oruser defined template.Electronic records and signaturesThe advanced mode can be combinedwith the security pack to support 21CFR part 11.Advanced automationWith the advanced automationcapability you can perform fullyautomatically complex measurement,data evaluation, and report generationsequences using single or multiplemethods for different types of samples.It can also be used to guide anoperator through a complex sequenceof manual measurement operations.Complex methods or automationprocesses that you develop on theadvanced system can be transferred toand executed on the general purposesystem.67Multi-component analysis withdiagnostic tools that show the quality of the resultsThe OptimizeStandards function shows thewavelengths that give the best calibration8Thermal denaturationresults are calculatedusing your ownequationMicrosamplingA frequent problem for the biochemistis the small sample volume availablefor analysis. With the Agilent 8453spectrophotometer you can usemicrocells requiring as little as 15 µLof sample for qualitative and precisequantitative analysis.Multicell kineticsFor productivity with enzyme kineticmeasurements the optional eight-position multicell transport can beused. You can freely configure whichpositions contain samples and blanksand you can select to subtract the rateof one cell from the others.You can evaluate kinetic rates at a singlewavelength or subtract a referencewavelength. Rate calculation methodsinclude initial rate, zero order, first order,and delta absorbance. For a single cellyou can also display and calculaterates at up to six individual wavelengths.Solutions for biochemical analysisKey biochemical applications in a single, easy-to-use systemEase of useThe biochemical analysis software buildson the Agilent 8453 UV-visible spectros-copy system. It provides the additionaltasks that the biochemist needs anduses the same easy-to-use graphicaluser interface. Preprogrammed methodsfor protein and nucleic acid analysishelp you get up and running fast.Proteins and nucleic acidsStandard methods are provided for thequalitative and quantitative analysis ofnucleic acids and proteins:•260/280 nm ratios for nucleic acidpurity•Warburg-Christian calculation ofconcentration of nucleic acid orprotein in mixtures•Biuret, Lowry, Modified Lowry,Bradford, Bicinchoic acid, andTrinitrobenzene sulfonate proteinquantification methodsFull spectra are alwaysacquired, even inmulticell kinetics,so you can re-evaluateresults at leisureThermal denaturationWith the Peltier temperature controlleryou can perform thermal denaturationexperiments such as DNA melt testingand protein unfolding. You can selectyour own multi-step heating and coolingprogram and, while the run is in progress,you are kept up to date with display ofactual and target temperature, and thethermal denaturation trace at yourspecified wavelength. Results can beevaluated using average or derivativemethods to calculate transitiontemperatures and standard or user-entered equations to calculate %GC.Solutions for chemical analysis At a glanceSelection of software modulesAdapt the 8453 spectroscopy systemto your needs by adding differentsoftware modules to the general-purpose software. One or more modulescan be added to at the same time tosupport different applications.•General-purpose software, includingverification and diagnostics, forstandard applications•Advanced software for morecapabilities in data evaluation,method development and automation•Biochemical analysis software, including kinetics and thermal denaturation•Dissolution testing software for single and multibath dissolution testing•OpenLAB enterprise content manager for handling and sharing methods and data across the web •Security pack software to support compliance with 21 CFR Part 11Increasing productivityThe UV-visible ChemStation software allows control of different sampling systems to increase throughput. A common feature of the general purpose, advanced and dissolution software is that the predefined methods work with different sampling systems – without changing parameters.Therefore, a method developed for manual sampling can easily be used with a sipper or autosampler, depending on the actual demand.8453 spectroscopy system with general purpose UV-visible ChemStation software910Accessories•Full control through software •Eight cell positions (for example, one blank and seven samples)•Random access to all positions•Water-thermostattable using externalwater bath, 5–90 °C temperature rangeand ±0.3 degrees temperature difference between any two cells at 37 °C •Less than 1 second to move between adjacent cells•±0.1 mm position repeatability •Optional water-driven magnetic stirring module Sipper systemFor repetitive measurement of liquid samples a sipper system improves productivity and eliminates errors caused by manual cell handling. The Agilent sipper system comprises a peristaltic pump and a quartz flow cell:•Full control through software •Variable pump, delay, and return time •Flow cell with 10 mm path length,3 mm diameter, and 80 µL volume •Constant-speed peristaltic pump with Tygon pump tubing •Minimum sample volume of approximately 1 mL•Typical sampling time of 20 secondsCell holdersAgilent Technologies offers a range of single cell holders, providing you with the ability to analyze a wide variety of samples. Unless otherwise stated the holders accept cells with path lengths up to 10 mm.Standard cell holder:Ensures quick and precise cell positioning for each measurement. Supplied standard with all Agilent spectrophotometers.Thermostattable cell holder: When connected to a circulating-water bath,ensures constant sample temperature for temperature-sensitive analyses. An optional accessory provides water-driven stirring with magnetic stirring bar for 10-mm cells.Long-path length cell holder: Holds rectangular and cylindrical cells with path lengths up to 100 mm.Multicell transportThe multicell transport provides a significant increase in productivity when you need to do simple, repetitive measurements on a small number of samples, or when you want to follow changes in several samples (for example,enzyme kinetic studies). The multicell transport features:Peltier thermostatted cell holder Use the Peltier controller and cell holder when you require precise or variable temperature control:•Built-in magnetic stirrer•Heat exchanger for sample pre-heatingwhen using sipper system•Fully controlled through software and GPIB interface •External sensor for precise sample temperature (optional)•Typical range of 10–100 °C (-10 to +80 degrees relative to ambient) without need for water cooling •Accuracy of ±0.2 degrees at 20–40 °C, ±0.3 degrees at 0–20 °C and 40–60 °C,±0.5 degrees at 60–100 °C •Reproducibility of ±0.1 degrees at 0–60 °C, ±0.2 degrees at > 60 °C •Stiring speed of 40–1000 rpmCell holders Peltier thermostatted cell holderMulticell transport11•Flow cells of different designs with screw fittings and path lengths of 0.1, 0.2, 0.5 1, 2, 5 and 10 mm •Semi-micro and micro cells with path lengths of 2 and 10 mm for minimum sample volumes of 15 and 60 µL respectivelyThird-party accessoriesA wide range of accessories, designed for or compatible with Agilent spectro-photometers are available:•Custom Sensors & Technology fiber optics coupler, fibers and sampling devices •DBS Peltier devices for single cell and multicell transport •Gilson autosamplers that arecontrolled directly from the Agilent UV-visible ChemStation software •Labsphere diffuse reflectance accessories•Applied Photophysics stopped-flow accessory for fast kinetics •Hi-Tech stopped-flow accessory for fast kinetics•Distek dissolution bathsAutosamplerCombine an XY autosampler with a sipper system and you can measure large numbers of samples fully auto-matically in unattended mode. The XY autosampler features:•Full control through software •Capacity of up to 240 samples •Wash station for optional rinsing between samples•10–13-mm diameter sample tubes with maximum height of 100 mm•Typical transit time (adjacent samples) of approximately 6 seconds (including raising and lowering probe)•Typical time per sample of 25 seconds (including sipper operation time)•Minimum sample volume of 2 mL.CellsAgilent Technologies offers a range of quartz cells for standard and flow-through operation including:•Regular rectangular cells with path lengths of 1, 2, and 10 mm •Cylindrical cell with 100-mm path length•Stoppered cells to protect your sample from air and ideal for use with the external sensor of the Peltier temperature controllerSipper system Autosampler CellsAgilent supportAgilent has support centers in 85countries supplying a wide range of support products that can be tailored to your needs.For example, the Agilent network of Analytical Response Centers provides direct access to support professionals who help you resolve operational difficulties, and offer assistance and advice on running Agilent chemical analysis software. They also help you to solve analytical problems, to keep your equipment up to date, and to maintain GLP standards.All of us at Agilent are here to help you meet your chemical analysis goals,not just now but also long into the future.Ask your Agilent representative for more details or see the Agilent Columns and Supplies /chem/suppliesLearn more:/chem/uvBuy online:/chem/storeFind an Agilent customer center in your country: /chem/contactusU.S. and Canada1-800-227-9770*****************************Europe************************Asia Pacific**************************** Microsoft is a U.S. registered trademarkof Microsoft Corporation.© Copyright 2008 Agilent Technologies Published July 1, 2008Publication Number 5989-8680EN。
空调系统臭氧消毒效果验证
xxxx有限责任公司空调系统臭氧消毒效果验证方案文件编号：版本号：生效日期：制订部门：制造部空调系统臭氧消毒效果验证方案目录1.0目的 (3)2.0范围 (3)3.0责任 (4)4.0参考文件 (4)5.0系统描述 (4)6. 培训 (5)7.0试验用仪器及试剂 (5)8. 实施程序 (5)9. 验证的实施 (5)10.0总结报告 (9)11.0再验证周期 (10)12.0最终结果审批 (10)13.0附件清单 (11)14.0文件归档管理 (11)15.0附录 (11)空调系统臭氧消毒效果验证方案方案审批表文件责任姓名职位签名日期制订验证小组成员审核验证小组QA成员审核验证小组组长审核质量部负责人批准质量负责人1.0 目的通过对在一定的时间洁净室（区）内臭氧浓度的测试，验证在规定的时间内洁净区各洁净间臭氧浓度是否达到标准规定；通过微生物挑战性试验，确定在一定时间内臭氧对洁净室（区）的灭菌效果。
2.0 范围适用于生产区所有洁净室空调系统抽样消毒效果的验证。
空调系统臭氧消毒效果验证方案3.0 责任3.1各部门职责3.1.1质量负责人负责对验证方案和验证报告的批准。
3.1.2 质量部根据GMP和质量管理的要求对本验证方案和报告进行审核和确认。
负责对验证所需的试剂和培养基进行确认。
负责监督管理整个验证活动，确保验证按计划进度进行。
3.1.3 制造部负责本验证方案及验证报告的起草和编写。
负责整个验证工作的实施。
负责提供验证工作相关资料，并组织协调参与验证人员，确保验证工作的正常进行。
负责对系统有关安全、环保、职业健康的相关设计进行审核和确认。
4.0 参考文件《药品生产质量管理规范》（2010修订）《药品GMP指南》（2011版）《药品微生物学检查技术》5.0 系统描述臭氧在常温、常压下结构不稳定，很快自行分解氧气（O2）和单个氧原子（O）；后者具有很强的活性，对细菌有极强的氧化作用，臭氧氧化分解了细菌内部氧化葡萄糖所必须的酶，从而皮坏其细胞膜，将它杀死。
AVANT 数据采集与信号分析仪
系统硬件
输入通道 通道数 模拟滤波 数字滤波 电压范围 量程 分辨率 输入阻抗 动态范围 谐波失真 通道匹配
采样频率 传感器类型 耦合方式
ICP 恒流源 信噪比 频率精度
单机 8, 16 通道，同步输入 每通道独立的模拟抗混叠滤波器 每通道独立的 160dB/Oct 数字滤波器 ±10VPEAK 0.1V, 1V, 10V 24 位模数转换器(ADC)
频谱分析
数据记录 用于离线分析
频率范围 最高 76800Hz
分析谱线 50、100、200、400、800、1600、3200、 信号计算
6400、12800
信号计算 生成用户定制的信号， 在测试过程中，所
窗 函 数 Rectangle、Hanning、Hamming、
有信号的计算和显示均在线完成
Exponential、Bartlett、Welch、Tukey、 计算方法 数学计算 (加、减、乘、除、平方、指数、
触 发 沿 上升沿、下降沿、双沿
Y1、X2、Y2 值，自动计算 POWER、ΔRMS
触发量级 设定量程范围内的电压值
光标联动 多个窗口的光标同步移动
无 触 发 延时
谐波光标 标记谐波，自动计算谐波失真度
触发模式 超前、滞后
峰/谷值光标 自动峰值/谷值探测并标记
运行模式 第一帧触发后自由运行、每帧手动触发、
MI-7801 数据采集与频谱分析软件包(内含信号源) MI-7804 声学分析(声压与声功率分析) MI-7805 旋转机械与阶比分析 MI-7806 冲击波形瞬态捕捉与冲击响应谱分析 MI-7807 模态数据采集 SAS-155 液压阀计算机测试
MI-7802 数据记录与离线分析软件 SAS-160 模态分析软件 ME'scopeVES SAS-200 离线分析 AVANTCAL-100 重校验软件 (硬件校准软件)
浙江省计量院收费标准
台 台 台 台
2000元 500元 1300元 1000元
10 11 12 13 14
按客户约定 （0～1000）mg/L 按客户要求配制 （0～20）mg/L （0～20）mg/L
台 台 台 台 台
2000元 2000元 2000元 1000元 1500元 650元 650元 540元 500元 500元 500元 500元 650元 1500元 420元
1500 590 590 320 800 1500 800 500 1500 300 1000 400 480
79 黑白密度片 80 81 82 83 84 85 86 X射线探伤 机 γ 射线探伤 机 涡流探伤机 固定式磁粉 探伤机 便携式磁粉 探伤仪 看谱镜 磨耗仪
电子式0.01 （30～40000）r/min 级以下 87 转速表 离心式、定 时式、磁电 10Hz~10MHz 式0.25级及 以下 转速标准装 0.01级及以 （30～40000）r/min 88 置 下 （30～40000） r/min 车速里程表 89 0.1级 标准装置 100Hz～10MHz 电梯限速器 1.00m/s～10.00m/s 90 / 测试仪 （100～40000）r/min 91 离心机 /
收费单位
收费标准 不含下场 费用） 600元 600元 1000元
备注
台 台 台
4 电导率仪
台
600元
5
在线电导率 仪
台
600元
6 pH计检定仪 7 8 9 含水率测量 仪 自动电位滴 定仪 卡尔费休容 量法水分滴 定仪 卡尔费休库 仑法微量水 分测定仪 总有机碳分 析仪 电导法总有 机碳分析仪 覆膜电极溶 解氧测定仪 在线覆膜电 极溶解氧测 定仪
印刷式固态聚合物电化学气体传感器
Application Scene
传感器入厂品质检验 故障传感器检测 仪表研发阶段的对比测试和验证 仪表选型或安装选点的现场气体测试 用于室内或特定环境的气体检测
Easy Board气体检测模块
Easy Board detection module
特点
Characteristic
小体积，直插式排针连接方式 适配ES1 / ES4 / EC4系列电化学气体传感器 标准电压输出，2.4~5V供电 尺寸：22x18x12mm
网络化多工作站系统
Networked multi station system
软件界面
Software Interface
产品选型表
Product selection form
ES1- Easy Gas Sensors
Item
Gas
1 All Gas/VOC 2 All Gas/VOC 3 All Gas/VOC 4 CO 5 CO 6 CO 7 H2 8 H2 9 H2S 10 H2S 11 H2S 12 NO2 13 NO2 14 NO2 15 HCN 16 O2 (Bias voltage) 17 HCHO 18 SO2
系统组成
System composition
配气系统: 干湿配气系统基础单元/控制系统/干燥零气系统/标气流量控制系统 测试系统: 传感器/仪器测试工装、传感器/仪器信号采集系统/温湿度环境模拟系统 软件系统: 电脑/工控机/上位机软件
系统特点
System Characteristics
模块化的系统设计，每个模块可以独立购买使用 一套系统可以同时控制10个工作站 同时可以混合5种目标气体 可以同时进行两路气体的测试 独特、科学的气路系统设计 让批量测试的传感器/仪器同一时间接触气体 批处理程序可以快速、批量化检测 批处理程序运行复杂的检测条件，比如用于欧洲标准的测试 可以生成检测或测试报告 原始测试数据可以自动存储到服务器 打印用户定制的商标 满足实验室设备的法规要求 系统实现自动控制温湿度实验箱 可以随时随地通过网络进行远程启动试验，或检查试验过程或结果
GX-2009四合一检测仪简易操作步骤
日本理研GX-2009中文说操作说明此检测仪能同时检测大气中的氧气O2、可燃性气体HC 、毒性气体(一氧化碳CO 和硫化氢H2S)。
1、使 用 方 法：(1) 持续按住“POWER ／MODE ”键一秒后，听到蜂鸣声后，电源打开。
开机如发生电池电量不足的报警（蜂鸣器：1秒间隔连续鸣叫；报警灯：1秒间隔连续启动；屏幕上显示“FAIL BRTTERY ”。
）， 此设备不能进行任何检测。
如在使用的情况下，应马上关闭电源，然后到非危险场所进行充电。
(2) 电源开启后，本检测仪会自动进入检测模式。
画面显示各传感器所检测的气体浓度。
(3) 持续4秒按住“MODE/POWER ”键，电源将被关闭；(4) 在关闭电源前，请将各项目都归零后(氧气：20.9%)，再关闭电源。
2、空气校对的操作： 使用本检测仪时，在检测前务必要在清新的空气中进行空气校对。
(1) 在检测模式中，持续按下“AIR ”键。
(2) 蜂鸣器会“哔”的鸣叫一声。
当蜂鸣器再次“哔”的鸣叫一声后，画面下部纪录栏中显示“RELEACE ”后，松开“AIR ”键。
(3) 大约4秒后，进行自动校对。
(4) 请确认画面显示是否全部归零(氧气：20.9%)3、在检测模式下转换表示模式：在检测模式的情况下，通过按动“POWER ／AIR ”键，可以转换画面显示内容具体显示如下。
备 注：· 测定瓦斯的浓度值表示，显示的是当下的检测值。
· 峰值表示，显示的是开启电源后的最大或者最小值(氧气表示为最小值)。
通过持续按动“AIR ”键，可以进行清除。
· 全量程表示，表示的是各种气体的-----检测范围。
在全量程表示的画面中，通过按动“AIR ”键，画面会进行如下转换。
· 无论画面显示的是什么内容，当按动“POWER ／MODE ”键后，都会转换到检测画面。
4、气体报警的种类和类型：【报警时、报警灯的动作】气体报警时，报警灯按照①→②→③→①···的顺序循环点灯。
thermo scientific 46i原理
Thermo Scientific 46i原理介绍Thermo Scientific 46i是一种高级的气体分析仪器，广泛应用于环境监测、工业过程控制以及科学研究等领域。
该仪器以其卓越的性能和精确的测量结果而闻名，下面将为您介绍其原理和工作方式。
Thermo Scientific 46i基于红外吸收光谱技术，用于测量大气中的气体浓度，特别是二氧化硫（SO2）和二氧化氮（NO2）。
它的工作原理是通过检测样品中特定气体分子对红外光的吸收来测量其浓度。
在仪器内部，红外光源会产生一束特定波长的红外光。
这束光经过一个光学系统，然后通过一个吸收室，该吸收室中的样品气体会吸收特定波长的红外光。
吸收室的设计和材料会确保只有目标气体分子会吸收光线，而其他气体分子不会。
在光线通过吸收室后，它会进入一个光检测器。
检测器会测量光线的强度，并将结果转化为电信号。
这个电信号经过放大和处理后，会被转化为气体浓度的读数。
通过比较样品气体吸收前后的光线强度，仪器可以准确计算出气体浓度。
Thermo Scientific 46i具有高度的稳定性和精确性。
它采用了先进的光学设计和数字信号处理技术，可以消除环境中的干扰因素，如湿度和温度变化，以确保测量结果的准确性。
此外，该仪器还具有自动校准和故障诊断功能，可以提高实验室操作的便利性和效率。
Thermo Scientific 46i的应用领域广泛。
在环境监测方面，它可以用于监测大气中的污染物浓度，帮助评估空气质量和环境保护措施的效果。
在工业过程控制中，它可以用于监测废气排放，以确保生产过程符合环保标准。
在科学研究中，它可以用于分析大气化学反应和研究气候变化等问题。
总之，Thermo Scientific 46i是一种可靠、精确的气体分析仪器，其红外吸收光谱技术使其在大气监测和工业应用中得到广泛应用。
通过了解其原理和工作方式，我们可以更好地理解和利用该仪器的优势，为环境保护和科学研究做出贡献。
哈希公司水质监测仪器说明书
哈希公司成立于1947年，现为美国丹纳赫集团一级子公司，总部设在美国科罗拉多州的拉夫兰市，是设计和制造水质、水文监测仪器的专业厂家。
工厂分别分布于美国、瑞士、德国、法国和英国。
作为水质、水文监测仪器的世界领导者，哈希公司产品被全球用户广泛应用于饮用水、地下水、地表水、市政污水、工业污水、半导体超纯水、制药/电力及其他工业净水、等领域，其全线产品系列涵盖实验室定性/定量分析、现场分析、流动分析测试、在线分析测试。
产品具有测量精确、运行可靠、操作简单、低维护量，结构紧凑等特点。
哈希公司一直致力于使水质分析过程更方便、更迅捷、更可靠：各类包装的即开即用型化学试剂包，不仅为精确的化学分析提供了可靠的质量保障，也为用户节约了宝贵的时间和人力资源,成为了中国环境现场应急监测的首选工具；各种类型的在线水质分析仪器，以其准确度高、维护量小、可测量的水质参数多等特点，可以满足污水处理厂、饮用水厂、工业过程水处理、工业污染源、水质自动监测站等不同场合的应用。
哈希公司的水质分析仪器产品在中国已经有超过20年的成功应用， 哈希在线水质分析仪器在中国水处理市场以及全球范围内都得到了广泛的应用，一直以来哈希在线浊度分析仪都是饮用水行业关键性运行指标－浊度测试的常用仪器。
我们的目标是继续为广大用户提供可靠的仪器、测试方法、简单的操作步骤和优质的客户服务，不断地提高产品的质量以满足客户需求不断变化的需要。
目前公司已经在北京、上海、广州和重庆、沈阳、西安、武汉、济南、南京、福州设立了办事处，为中国的广大客户提供方便、周到的服务。
目录水位监测 (2)流量监测 (12)雨量监测 (29)气象监测 (31)水质监测 (33)典型应用 (60)基本介绍用于连续测量水位的精巧型气泡水位计。
它具有高量程、高精度的特点，并带有4－20 mA 模拟输出和SDI12标准接口，最新设计的智能型气泵可以在满足测量精度的前提下减小打气体积，以便节省系统功耗。
4160甲醛分析仪操作步骤
4160甲醛分析仪操作步骤
1.检查电池仪器使用前必须检查电池电量。
把功能开关
（FUCTION）调到BAT.TEST“A”，若显示电池电压大于1才可以正常使用，否则应该充电（充电时间16h）。
将功能开关（FUCTION）调到BAT.TEST“B”若显示电池电压大于1.0才可以正常使用，否则应该更换碱性电池。
2.连接采样管将C12F过滤器两头的小红帽取出（用完后，必须将
小红帽再盖严）。
另有一个由两个不同粗细联成的软管，将粗的一端连接接到C12F过滤器的任意一端，将细的一端接到采气管上。
采气管与仪器背面的进气口（in口）相连。
安装工作完成。
3.调零与测试零点调节是在SAMPLE(采样) 模式下进行的，将采
样管连接到仪器进气口，在测量现场将C12F过滤器用过滤软管接到采样管上，将气体过滤成零气。
注意在调零旋钮调零之前，仪器指示要稳定。
取下C12-F过滤器，仪器稳定后的读数即为现场的甲醛浓度。
4.关机测试完毕后，如果测试点的浓度太高，关闭前应让将采样
管移到大气中将浓度降到较低值后再关闭（调到“OFF”）。
49i臭氧分析仪 中文说明书
热电49i臭氧分析仪技术资料方法标准：ISO15438-1995方法名称：紫外光度法页脚内容1山东美吉佳环境科技有限公司页脚内容2第一章简介产品性能49I分析仪是一种使用紫外灯测定臭氧的分析仪结合检测技术，轻松利用菜单驱动软件和高级诊断提供了极其卓越的适应性和可靠性。
49I分析仪具有以下的特征：·320*240液晶图像显示·菜单驱动软件·区域可定量程·用户自选单/双/自动量程模式·多重用户自定义模拟输出·模拟输入选择·高灵敏度·快速响应时间·全量程线性·双重反应室测定防止可能冲突·自动温度压力补偿·用户自选数字输入/输出容量·标准通讯特色包括RS232/485和以太网页脚内容3·C-Link, MODBUS协议,以及流动数据协议工作原理49I分析仪是基于O3分子吸收波长为254nm的紫外光，被吸收的紫外光的程度与下面的定律有关：通过过滤器进入49I仪器的样气分为两部分，如图1-1所示.一路气体流过臭氧的洗刷器而成为参考气体(Io),然后进入参考电磁阀, 而样气(I)则直接进入采样电磁阀.电磁阀在反应室A和B之间每10分钟转换一次参考气体和样气,当A室是参考气体的时候则B室就是样气,这样来回交替.紫外光的强度由在每个反应室中的探测器A和B来测量.当电磁阀的开关在参考气体和样气之间转换时,其中几秒的时间的光强度变化允许误差可以忽略,49I仪器为每个反应室计算臭氧的浓度,前面板输出浓度是两反应室浓度的平均值. 模拟输出也可以通过以太网连接获得.页脚内容4页脚内容5第二章使用说明书本章介绍前面板的屏幕显示、前面板上的按键及菜单驱动软件显示屏屏幕为320x240LCD显示屏，可显示样气的浓度、仪器的参数、仪器的控制及帮助信息。
有时菜单所包括的内容较多，屏幕不能同时显示菜单的全部内容。
高频红外碳硫分析仪技术参数
高频红外碳硫分析仪技术参数一、主要技术指标1.分析品种：各类金属、铁合金、矿石、稀土金属及贵金属、有机或无机盐类以及各种固态材料中碳硫含量的分析。
2.分析范围：低碳0.00001-0.3%高碳0.01-100%低硫0.00001~1%高硫1.%~100%3.分析时间：20〜90秒设定可调，常规20〜40秒可调。
4.灵敏度：碳0.000001% 硫0.000001%分析精度：碳:RSD<0.5% 硫:RSDWI.5%5.分析误差：碳：满足ISO9556硫：满足ISO49356.校正方式：单点或多点、线性校正7.高频感应炉：输入功率三5KW∕20MHz输出功率23.5KW∕20MHz输入电流15A加热时间1・99秒可调（由红外分析仪控制）加热温度1700℃（可调）升降炉膛氧气压力0.4—0.6MPa最大炉膛压力0.08MPa8.炉头自动加热、恒温。
消除粉尘吸附对测定的影响，开机后即可进行检测，无须对气路饱和处理，无论间隔测定或连续测定都有同样的稳定性。
9.自动清灰除尘系统。
10.超纯金箔红外池，可以有效提高超低碳、硫检测的灵敏度，满足低碳、硫（PPm）分析的需求。
11.超微孔金属过滤器（0.5微米），能可靠地过滤燃烧气中的粉尘，整体烧结成型，无须超声波清洗剂即可长时间使用。
12.测试软件全中文界面。
具有实时曲线显示、自动校正，曲线存储，空白扣除、参数设定、数据设定、数据入库（标样库、试样库、重量库）、数理统计，数据复算，并有完备的自检诊断功能、超大容量的数据存储及计算功能。
13.有“示波器功能”：根据信号电压幅值及波形，可及时准确判断光源、切光马达、切光片、热释电传感器及前置放大等部件的运行状况。
14.自动报警功能：机内无重量、通道参数改变、设定条件错误、样品未作、未选择标样、通讯不正常等异常情况时，均可显示有关的报警信号。
15.设备配置15.1、高频红外碳硫分析仪1套15.2、品牌电脑1台15.3、稳压电源：5kVA15.4、马弗炉一台：发热体类型：硅碳棒使用容积：不低于201.温度范围：0℃〜1300℃二、设备工作条件、温度：电源：220V±5%,50Hz±2%；室内温度：15-35C；相对湿度：≤85%设备在上述工作环境下能长期、稳定的保持其工作性能。
产品及零部件编码规则
产品及零部件编码规则1目的为了在保证产品及零、部件管理连续性的基础上，进一步完善产品及零、部件的管理，以使所有的产品及零、部件命名得到规范和统一，特编写此规则，力求做到:1)反映元件的主要特征；2)能区别同类元件的不同产品及零、部件；3)易懂，易记忆4)方便书写、记录和计算机输入.2适用范围1)本文件规定了公司产品及零、部件的编号规则。
2)本规则适用于本公司采购、生产、供货、试验的所有产品零部件。
3职责1)研发部负责产品及零、部件编码的规定及编制工作,确保不重码；如果原有产品及零、部件代码需要变更，研发部负责向相关部门发放更改通知单.2)各部门负责审核所管辖产品及零、部件编码的合理性，并批准实施。
3)各部门负责落实产品及零、部件编码的管理制度。
4编码的基本原则编码应体现科学化、标准化、规范化、合理化。
具备唯一性：所有产品及零、部件均应按照本编码规则编制，每种产品及零、部件的编码是唯一的。
可以扩充：适当留下可扩充之流水号，避免新增元件无法加入而致使元件重编。
反映重要属性：需加以大中分类以利于以后报表的整理。
产品及零、部件编码应具有一定的意义,但又不能包含太多的意义，以免影响编码的通用性与适用性。
变动属性不纳入：属于部门、供应商、客户、员工等属性不纳入编码。
产品及零、部件编码中包含的含义只是一些不会变的属性。
产品及零、部件编码在产品及零、部件整个流程是不变的。
码长定为12位，除首位用字母表示，其它用阿拉伯数字表示。
产品及零、部件代码的分配，统一由公司文控中心负责，并通知库房及时录入计算机系统。
产品及零、部件将以其编码为主体运作，各相关受控或不受控的文件、业务单据、BOM 等均使用产品及零、部件编码。
产品及零、部件编码的大、中各类及明细可随公司的需要而增加,但不可删改.5编码规则内容编码由“产品分类码+产品大类码+产品小类码+产品特性码+产品子类码+零部件序列码”组成,共计12位编码，各字段定义内容如下:1 2 3 4 5 6 7 8 9 10 11 12X XX XX XX XX XXX ↓↓↓↓↓↓零部件序列产品分类码产品大类码产品小类码产品特性码产品子类码码产品及零、部件编码字段定义6编码的管理和使用1)产品及零、部件编码按照编码和产品及零、部件本身一对一原则进行,不得出现一对多或多对一的情况,一旦发现,立即纠正，涉及产品及零、部件在问题解决之前，不得使用。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
RAN GE SER. NO.
dimensional outline
The OZONE ANALYZER BMT 964 C is housed in a powder coated aluminum cabinet. The space needed (door open, sample gas tubing and cables connected) is approx. 480 x 240 x 420 mm (W x H x D). The cabinet can be wallmounted using the four brackets provided at the rear (four mounting holes 6 mm ID, spaced 240 x 225 mm, W x H). For sample gas connection 3 x 5 mm (or 1/8'' x 3/16'') PTFE tubing should be used. The BMT 964 C is also available with 1/8'' or 1/4" Swagelok fittings and steel tubing to the Catalyzing Cartridge. Additional BMT Products (for details, refer to the appropriate data sheets): BMT 964 BT (Bench Top) for stand-alone applications on the bench, or in the field BMT 964 AQ and BMT 964 AQ-INLINE for ozone measurement in DI (de-ionized) water BMT 964 AQ/HF for ozone measurement in DI water with HF BMT DH3 Sample Gas Dehumidifier for drying of wet ozone sample gas BMT 930 Ozone Monitor for TLV monitoring in ambient air (1, 3 & 6 channels) A broad spectrum of field-proven accessories - from simple fittings and tubing up to the thermoelectric sample gas dryer DH3 - helps the user with the application and installation of the OZONE ANALYZER BMT 964 C. Please ask for our assistance!
BMT MESSTECHNIK GMBH
பைடு நூலகம்
SPECIFICATIONS measurement principle dual-beam UV photometer (254 nm), no moving parts MTBF instrument incl. UV lamp 65,000 h, excl. UV lamp 120,000 h UV lamp low pressure mercury lamp, long life design, burnt-in for 300 h display 16 character alphanumeric backlit LCD concentration ranges 50, 100, 200, 300, 400 g/Nm3, selectable units g/Nm3, %wt/wt and ppmv optional ranges 10, 20 g/Nm3, selectable units g/Nm3, %wt/wt and ppmv concentration error 0.5 % max. repeatability error 0.2 % max. response time 0.03 s (analog output), 0.3 s (display) zero drift 0.2 % per day, after 10 minutes warm-up, non-cumulative proof pressure 1 bar above pressure range ambient temperature 0 - 50°C (non-condensing) materials in contact quartz (cuvette windows), Al2O3 (cuvette), with ozone FFPM (window seals), PTFE (tubing), stainless steel (fittings, cuvette spacer) gas ports for PTFE tubing 3 x 5 mm (1/8" x 3/16"), opt. 1/8'' or 1/4" Swagelok, 4x6mm PTFE Built-in sample gas filter is standard recommended flow rate 0.1 to 1 l/min typical pressure drop approx. 5 mbar at 0.5 l/min (throttle valve fully open) temperature compens. is standard pressure compensation with built-in cuvette pressure transducer, for ozone measurement at an arbitrary systemic pressure, abs. pressure range 1.15 bar (optional up to 3.5 bar in steps of 0.5, please specify) units selectable: bar, psi, Torr, Mpa signal outputs concentration 4 - 20 mA (isolated, active) concentration 0 - 10 V (isolated) concentration alarms High Alarm, Low Alarm, latching, not latching control input set to zero (24 V, 18 mA, isolated) control outputs relay contacts, 28 V, 0.5 A, isolated: Lamp Low Cuvette Dirty High Alarm Low Alarm error handling Error Relay: 30 V, 1 A, summarizing instrument failures Warnings and errors: Lamp Low Warning, Lamp Low Error, Lamp Off Error, Cuvette Dirty Warning, Cuvette Dirty Error, Overrange, Overpressure serial interface RS-232, bidirectional, isolated, 2400 - 38400 Baud automatic zeroing with internal purge pump and solenoid valve only with pressure range 1.15 bara software BMT 964 Link, instrument configuration, readout of Event & Error Logs (Windows) power wide range input: 85 - 264 VAC, 35 VA dimensions (W x H x D) 300 x 200 x 120 mm (W x H x D) weight 3.9 kg compliance CE-marked (EMC & safety), cTUVus NRTL-listed
The OZONE ANALYZER BMT 964 C is the wall-mount version of the standard BMT 964 (see data sheet of standard BMT 964) for application in a hostile environment. It is housed in a splashproof IP 65 (NEMA 4X) aluminum cabinet, and is equipped with everything needed for fully automatic stand-alone operation. Fully automatic means: a purge unit is provided which consists of a 3-way solenoid valve, and an air pump with particle filter, both being controlled by the automatic purge timer of the analyser. The system automatically purges the cuvette with clean, filtered air, and then zeroes the analyser. The zeroing interval may be chosen between 1 and 99 hours. Stand-alone means: a sample gas filter is provided (external to the cabinet), a throttle valve, a flow meter (behind the front door), and a Catalyzing Cartridge (external). An external Dirt Trap to remove namely fluidic dirt before it can reach the analyser, may be provided on request. Superior stability of the photometer is achieved by use of a true dual beam optical system with an extremely long-life mercury lamp. MTBF of the instrument, including the lamp, is in excess of 65,000 hours. Excluding the lamp it is 120,000 hours.