工厂英语单词汇总
工厂常用英语单词
工厂常用英语单词1-1 Substitution1-1代用料balance 結余Alternate current交流電bar code label 條碼標籤AC inletAC插座(電源插座)base 基極基礎acceptable可接受的basic 基本的action行動行為battery 電池active有效的現行的bead core 磁線圈active area有效面積biased 偏置active model有效機種block NO 半成品號additional附加的blooming 涂層開花address label地址標籤board 廠牌板子adhesive膠有粘性的BOM:bill of material 物料清單adhesive three bond 綠膠bonded 粘合的adhesive silicone矽膠board corrugated paper 天地紙板(棧板上面及Monitor 上:)adjustment判斷調整bottom 底部adjust調整bracket 托架括弧AI fixtureAI電氣設備bridge rectifier 橋式整流器AI: auto insertion自動插件部brightness 亮度aid援助brightness uniformity 亮度一致性air condition空運條件bulk rectifiers 矯正器air rubble bag氣泡墊bulky 大宗的笨大的altitude高度bumps ripples 波紋ALU(capacitor)鋁質(電解電容)burning room 燒機房加溫室amber琥珀色by block NO 按機種半品料號階排列ampere安培by model NO 按機種排列amplifier放大器analog模擬cable 線analysis分析cable ties 束線袋application應用cablet bracket 固定片apply應用申請CAI:computer AID issuring 電腦自動模擬發料approval審核承認cancel 取消approve同意贊成CAP:Capacity 電容arrange整理CAP ALU ELECTROLYTIC-400V 鋁質電解電容400以上assign指定,分配CAP ALU ELECTROLYTIC-OTHE 電解電容attachment 附件CAP FILM SPECIAL 薄膜電容audio音頻CAP MEF 金屬化聚乙脂膜電容器audio board音量板CAP MEM 小型化塑膠電容(MEF)audit檢核CAP MPP 金屬化聚丙烯膜電容automatic degaussing自動消磁CAP PEI 聚丙乙烯膜電容(無感式)available 準備好的通用的CAP PEM 聚丙乙烯膜電容(有感式)CAP PPM 聚丙烯電容器collector 集電電路CAP PPN 聚丙烯薄膜電容color/colour 顏色CAP PPS 串連式聚丙烯膜電容器color sticker 彩色貼紙CAP PS 聚丙乙烯膜電容器度射column 列CAP TAN 鉭電容commodity 屬性種類CAP VARIABLE 可變電容common base 共基電路CAP Y Y電容common choke 環形濾波線圈CAR:corrective and action report 校正與預防措施報告common choke 普通扼流圈capability 性能能力company 公司capacitor 電容容量compare 比較對照capacity 能量電容compatibility 兼容性capatine/with 可連接/插上complain 抱怨capacity 電容component 零件calendar 日程表computer 計算機carton 紙箱condition 條件carton box 紙箱confirm 確定cause 原因connector 連接器CC resistor 碳合成電阻consumption 消耗CD(capacitor)陶瓷電容continue 繼續CEM resistor 水泥電阻control chart 控制圖center 中心contract 合同carbon film resistor 碳膜電阻contrast 對比度CR resistor 碳膜電阻(色碼電阻)control BD 控制板change your password 改變密碼core magnetic 磁鐵磁芯characteristics 特性corrective 改善的charge 使承擔使負擔cost 成本chart 流程圖coustomer 顧客客戶chassis 機座critical 極限限制check 檢查CRT 映像管check point 檢查點CRT board CRT電路板choke 扼流圈CRT GND WIRE CRT接地線chromaticity 色度CRT screw CRT螺絲circuit 電路CRT socket CRT插座circuit board 電路板CRT test CRT測試CKD-ID 位置CRT:cathode ray tube 陰極射線管cleaner naphtha 清潔劑current 電流clip 夾子cushion 墊片code 代碼CUT-IN code 切入代碼coil 線圈coil rotation 傾斜線圈daily 每日的coil choke 扼流線圈data display area dimension and posi 數據顯示區域coil degaussing 消磁線圈date 日期coil linear 枕型調整線圈date code label 日期標籤coil peaking 蜂化線圈direct current 直流電conductivity 電導率DC input impedance 直流輸入阻抗本冊英語單詞是工廠常用之基本詞匯.DAB C 第 1 頁共 13 頁DDC:display data channel 顯示器數據通道electrostatic 靜電defect 不良electrostatic discharge 放靜電deffused ambient 散射環境EMI:(Electronic&Magnetic Interfere 電磁干擾濾波器define 解釋emittor 放射極deflection 偏轉EN:engineer notice 工程通知degree 角度enclosure 包圍delete 刪除engineering specification 工程規范delivery 交貨enter 確認進入delivery order 送貨單environmental 環境的decide 解決決定裁決equivalent 等效description 規格說明error 錯誤destination 目的地ESD:electrical static discharge 靜電detail 明細estimate disable 預定的deviate 偏差excess 過剩diagonal 對角線exchange 交換differential amplifier 差分放大器exhausted 耗盡digital control multiscan color monit 數控多頻掃瞄彩色顯示explanation 解釋diode 二極体explode 使爆炸direct 直接external 外面的direct current 直流電disable 使無能factory 工廠discharge 泄放fail 失敗discriminate 區分fan 扇子disk driver 硬盤驅動器FBT:fly back transformer 高壓包display 顯示展示feature 特性display power management signal 顯示器電源管理信號feedback 回饋回接(geometry)distortion (几何)失真fotter plate 底座壓制片distribution 令發分配film stretch wrap 包裝機台伸縮膠膜dot pitch 點距filter 濾波器document center 文件中心final approved 核準door 門finance 財務dot 點first floor 一樓double 雙倍的function led lens 顯是燈座double thread screw 雙牙螺絲(鎖塑膠)flange hex nut 防滑螺絲DQA:design qaulity assurance 設計品質驗證課flat square screen 平面直角屏幕drop test 落下測試flex cable 多蕊電量dynamic 動態flow 流量dynamic performance defeat 動態測試不良flux 電通量dynamic HV 動態高壓flyback 返馳foot pad 角墊ear phone b/d 耳機機板foot-lamberts FL 亮度單位ECN:engineering change notice 工程變更通知form 表單ECR:engineering change request 工程變更申請format 格式化edit 編輯frame 構架electronic 電子F/C front cover 前殼fuse resistor 保險絲電阻information 信息function 功能運行input 投入function key 功能鍵input signal 輸入信號function test 功能測試inquiry 查詢fabricate 制作裝配inrush current 開機電流fuse 保險絲insert 插入fuse clip 保險絲座inspection 檢驗future 將來inspector 檢驗者instruction card 指示卡(牌)gap 縫隙insufficient solder 焊錫不足Gauss 高斯(磁場單位)insulation wire 絕緣導線generate 產生interiaced 交織geometry ate fixture&program internal audit 內部審核geometric distortion 几何失真invar 一種低澎脹合金goal 目標inventory 存貨good 良品好的invoice 發票good finished 成品IPQC:in process quality control 制程品質管制graphic 圖形IQC:incoming quality control 進料品質管制gross 總的ISO:international standard organizat 國際標準化組織gross request 總需求issue quantity 發料量guarantee 保證item 項目guide rail PC板保護條item master 料號主檔heat sink 散熱片jitter 抖動height 高jumper wire 跳線HI-POT OK label 高壓OK標籤junction 連接結HI-pot test 高壓測試high priority(use substitution item fi 第一優先(代用料)L/P:light&play L/P測試動態測試highlight 突出label 標簽hold 拿放抑制控制led 指示燈horizontal 水平的life test 壽命測試hot melt adhesives 熱容膠line date 上線日harness 排線linear filter 線性濾波變壓器humidity 濕度linearity 線性link bar 連接焊linear integrated circuit 線性集成電路local 本地的IC power 功率集成電路login 登入IC socket IC插座logout 登出IC(digital) AC 數位集成電路low radiation 低幅射IC(integrated circuit)集成電路luminance 揮發發揮idle 呆料illuminate 照亮MO:manufacture order 制令工單imagine sharpness 圖像清晰度M.T.B.F:mean time between failure 平均故障時間inductance 電感machine screw 機械螺絲inductor 電感器main 主要的第 3 頁共 13 頁LME F第 2 頁共 13 頁G H I Jmain board 主機板mainland 大陸name plate 裝飾片maintain 維護negative 否定的反向的負極性 major 主要的net shortage 淨需求maker 制造者network 綱路management 管理安排new model check list 新機種一線檢查表manual 說明書NG=NOT GOOD 非良品manual 用手的人工的說明書notice 通知manual PR 人工 PR NUT 螺帽manufacturing 制造master 主人掌握obligation 義務責任material 物料ohm 歐姆(電阻單位)material approve 物料承認書order 訂單material return 退料on hand 庫存maylar(capacitor)聚乙酯樹酯電容option 選擇MC:material control 物料控制OQC:out going quality control 出貸品質管制MCR:mechanical changed request 機構變更申請order balance 訂單余數MDR:material defeat report 物料不良報告original 最初ME:manufacture engineering 制造工程original material 原始材料本料measurement 測量outline 輪廓MEB(capacitor)金屬化多元指電容mechanical 機構的P.O:purchase order 採搆訂單melt 熔化熔解P.R: purchase request 採搆需求menu 菜單metal washer 金屬墊圈packing 包裝meter 測量儀表packing label 包裝祇箱標簽method 方法packing list 包裝明細MFG:manufacturing 制造pad 軟墊圈MI:manual insertion 手工插件pallet 棧板minor 次要的輕微的parameter 參數MIS:manage information system 資訊部part NO P/N 料號model 機種型號password 密碼口令model label(ID label)機種標籤payment term 付款期限model name 機種名稱PC:production control 生產控制MOF resistor 金屬膜電阻PCB board film PCB圖片moire 波紋PCB ckt PCB上位置monitor 顯示器PCB:print Circuit Board 印制線路板monthly 月度的PE BAG PE 袋MOS-FET 金氧場效電晶體PE:production engineering 產品工程MPP(capacitor)金屬化多元指電容peaking 峰值MRP FCST LIST MRP需求預測表relay 繼電器MRP:material request plan 物料需求計劃percentage 百分率MTL:material control 物料部資材部perform 履行magnetic field 磁場perform your own function 發揮自己的功能multiple 复合的多層次的performance 作業操作表演pilot lamp 指示燈recall复位收回pin assignment 管腳排布receiving接收pitch 間距receiving store收料倉pixel 象素象元receiving report收料報表plastic resin 合成松香rectangle矩形長方形plug 轉接頭rectifier整流器problem 問題,難題reduce減少plug and play 即插即用regulation管理調整規則polyfoam 保麗龍reject reason判退原因posistor 熱敏電阻reject判退posistor resistor 熱敏電阻(正溫度系數)relation關係positive 正極性的relay繼電器power 功率電力電源reply答复power cord 電源線request quatity需求量power knob 開關按鍵requirement要求power MO-SFET 功率晶體resistor電阻power switch 電源開關resolution解析度prevent 防止預防result結果prepared 放置模式準備resultant合成的結果preset mode 預調(畫面)retrace追蹤探查priority 優先revision修訂版procedure 程序過程rework重工processing 處理ripple波紋漣綺product tree diagram 產品樹狀圖rivet卯釘production 生產rotary VR:Variable Resistor可旋轉的可變電阻project engineer 項目工程師row行promote 促使rubber pad橡膠墊片proposed 建議,推薦power mos driver電源MOS驅動器protection 保護public inquiry 公共查詢sponge海棉public report 公共報表spring彈簧pulse 脈沖stability穩定性PUR purchase 採購購買standard標準的PVC insulator PVC 絕緣片static靜態的status狀況rag 抹布stock庫存品random 隨機的store儲藏range 範圍SUB assembly半品代號raster 光柵光域substitution代替替代代用料rate 比率suggestion建議意見ratings 預定值summary慨括R/C:rear cover 後殼supply供應reason 原因support支撐reason code 原因代碼surge 振蕩R P第 5 頁共 13 頁第 4 頁共 13 頁NOSP.S.I:production shippment inventionretail 零售suspend/stand by 中止/暫停等待等命swivel 旋轉speaker Assembly 喇叭組裝swivel ball底坐圓盤spec list 規格清單swivel base底盤spec 規格symopom現象special 特殊的synchronization同步specification 規格system系統status 狀況S.O :sale order業務訂單stock 庫存品S.O:shop order工單store 儲藏S.W:diode整流二極體SUB assembly 半品組裝S/N:series no流水號substituuon 代用的代用的safety code安規代碼suggestion 建議意見safety stock安全庫存summary 慨括sample樣品supply 供應schedule計劃support 支撐scope範圍screw 螺絲scrap報廢socket 插座screw螺絲swivel 旋轉screw+washer螺絲加墊片swivel ball 球座second source代用料swivel base 底盤sequence順序symoboy 現象selection選擇synchronization 同步separtesync分開信號system 系統series NO.系列號set up設立TANT(capacitor)鉭質電解電容shift轉移變化tape 膠帶shielding cover隔離罩tapping screw 缺口自攻螺絲ship date出貨日期target 目的shipment出貨TE:test engineering 測試工程shipping schedule 出貨計劃temperature 溫度shipping store出貨倉term 期限時限shortage缺料test pin 測試針插頭管腳shortage quantity缺料量test template 測試樣品signal to noise倍噪sponge 海棉simulation模擬模仿spark gap 放電管size by inch寬度thyristor ser 可控整流器slide SW/PUR SW/TACT 滑動/電源開關tilt 傾斜switch開關timing update 及時修改solder焊接焊接劑tolerance 容限誤差solder wire錫絲top/bottom 頂/底source資源TOTAL 總計spacer support間隔柱扣子trade 貿易商業spare parts備用品transter 調動spark gap放電隙transistor 三極管spark tube放電管transistor(TR)電晶體speaker 喇叭voltage/frequency 電壓/頻率VR knob 旋紐video mode descriptions 可視方式描述VR 可變電阻video b/d(CRT BD)CRT板video cable 信號線wafer 晶片干膠片wafer 封箱紙company policy&procedure 公司制度與規章warehouse 倉庫coding system 物料編號系統warning label 警告標簽item master 項目表warranty card 保證卡BOM bill of material 各機種之物料冊width 寬度component specification 材料規格書WIP work in process 在製品SRA substitution request authorizati 使用代料授權書wire 線材ECN engineering change notice 工程變更通知書wire saddle 隔離束線座notification 聯絡單engineering specificaton 工程規格書X-RAY label 輻射標簽alignment specification 調整規格書xformer 變壓器inspection specificaton 檢驗規格書xformer hordrive 水平驅動變壓器assembly process 制程指導書xformer pincusion 線性調整變壓assembly drawing 裝配圖xformer power 電源變壓器control run 小量試作管制MAP manufacturing assurance plan 制造品質保證計劃zenar diode 穩壓二極体check list criteria 檢驗表及標準uncommon list 機種差異表u/p unit price 單價CAR corrective action report 矯正改善報告uncommon list 專用材料表差異表SOP standard operation process 標準操作程序under request 超耗GR&R gauge reliability&repeatabili 可靠性標準校驗unformity 均衡性OSD INT MENU OSD功能說明upc label 客戶代碼標簽contrast 對比urgent 緊急的brightnes 亮度user control and indicate 用戶控製的及提示H.SIZE(H.=horizontal)水平尺寸user 使用者用戶H.Position 水平相位V.SIZE(V.=vertical)垂直尺寸V.D.S vender delivery schedule 廠商交貸計劃V.position 垂直中心VAL 單位V.pincushion 垂直針墊valid 有效的trapezoid 不規則四邊形variation 變化PIN/BALANCE 內凹/外凹varister 變阻器parallelogram 平行四邊形varistor resistor(vr)可變電阻rotation 旋轉傾斜video display interface 視頻顯示器接口color 顏色vendor 廠商 language 語言vertical 垂直的DISP.FREQ.(Display frequency)頻率顯示VESA:vedio electronic standard asso 示頻電子標準協會degauss 消磁VGA video graphic adapter 視頻圖形適配器recall 復歸VIA 通過H.moire H.一種有波紋的絲綢video cabel 信號線V.focus 垂直聚焦第 6 頁共 13 頁V 主要資料與文件W 第 7 頁共 13 頁T Z U Xvibration震動vibration test 震動測試PRE-alignment 1預調 1magnet 磁鐵PRE-alignment 2預調 2selicone 矽膠PRE-alignment 3預調 3glue 白膠rag 抹布hand gloves 手套burn in retest 加溫複檢cleaning solvent 清潔劑white balance 白平衡調整packing tape 膠帶center raster 底色調整lift pallet 棧板purity 色純hand lift 油壓車convergence=CG 收歛cart 手推車tilt 傾斜調整畫面不良代碼ATE 几何自動調整poor F/V adj 頻率轉換不良inspection 檢驗poor vertical 垂直不良INSP.2(convergence)收歛檢驗vert. over scan 垂直過大INSP.3(final)最終檢驗vert under scan 垂直過小safety inspection 安規檢驗poor vert linearity 垂直相性不良R/C screw 鎖後殼poor vert center 垂直中心不良R/C inspection/preparation 後殼檢驗與準備poor vert sync 垂直同步不良HI-POT test 高壓漏電測試vert damping 垂直反折cable tie 綁訊號線spot when power ON/OFF 關機打點monitor carrier 顯示器搬運vert white bar 一縱線packing station 包裝站別hor over scan 水平過大cleaning and wiping 去污與擦淨hor under scan 水平過小carton label 紙箱標簽retrace line 歸線model label 機種標簽hor no sync 水平不同步packing plastic 包裝塑膠袋子hor damping 水平反折putting manual 放入說明書手冊poor screen 畫面不良packing-carton box 包裝-紙箱poor center 水平中心不良finished goods filling 完成的貨物裝填dog ear 線性扭曲.拉角repair 修理poor hor linearity 左右大小格生產線常用名辭認識poor hor phase 水平相位不良board pallet 板子trap distortion 梯型不良stopper 踏板pincushipon distortion 針墊形不良electric screw driver 電槍smear 拖色拖影glue gun 膠槍red bias 紅色偏壓cutter nip 斜口鉗green bias 綠色偏壓long nose nip 長鼻鉗blue bias 藍色偏壓soldering iron 烙鐵red drive 紅色驅動solder lead 錫絲green drive 綠色驅動 45VPPdesoldering gun 吸錫器blue drive 藍色驅動multitester 三用電表poor focus 聚焦不良adjuster 調棒no picture 無影像hamlet chamber 磁場brightness too dark 畫面過暗counter 計數器相反raster show 底色不良color analyzer 色溫儀poor brightness F4F4不良poor contrast control 對比控制不良function key board Function key BDpoor brightness control 亮度控制不良audio board Audio BD poor G2G2控制不良speaker 喇叭poor bottom 按鍵無作用MIC phone 麥克風led off LED击陷不亮styrofoam 保麗龍tilt 縫隙.傾斜PE bag 塑膠袋F/C logo poor print 面框/印刷不良carton 紙箱poor video cable 信號線不良resistor 電阻insulator panel 安規片作業不良capacitor 電容poor covergence 收歛不良coil 電感(線圈)poor purity 色純度不良transistor 電晶體poor CRT CRT不良field effect transistor 場效電晶體no power 無電源integrated circuit 積體電路poor power saving 省電不良diode 二極體no raster 無光域variable resistor 可變電阻flash LED LED閃爍high voltage transformer 高壓變壓器smoking 冒煙.跳火yoke 便向軛poor degauss 消磁作用不良antenna 天線poor power SW 開關作用不良speaker 揚聲器poor start UP 起動不良poor voltage 電壓不良poor Hi-pot test 高壓測試不良not completely assembly 組裝未入interference 干擾reverse assembly 組裝反向moire 紋路assembly of lost part 組裝缺件noise 異聲.雜音poor wire dressing 佈線不良waggle 抖動.幌動.閃爍poor operating 作業不良ENGLISH DESCRIPTION poor assembly 組裝不良damage 損壞問題ground wire 接地線damage board PCB損壞degaussing coil 消磁線圈damage parts 零件損壞tilt coil=Rotation coil 傾斜線圈damage wire 線材損壞other wire 其他線材copper pad rising 銅箔翹皮anode cap 高壓帽cpper pad on board is broken 銅箔斷裂signal cable 信號線INSERTING PROBLEM插件問題label 標籤parts lost in AI AI缺件screw 螺絲wrong parts in AI AI錯件function key 功能鍵parts reversed in AI AI極性反front cover=F/C 前框parts is not insert into AI AI未插入rear cover=R/C 後框redundant parts in AI AI多件UL shield cover UL 安規片parts lost in MI MI缺件EMI shield cover EMI電磁干擾防護片wrong parts in MI MI錯件MPR II shield cover 幅射防護片parts reversed in MI MI極性反第 9 頁共 13 頁(組裝/包裝問題)第 8 頁共 13 頁CHINESE敘述(組裝段站別)FINAL ASSEMBLY STATION ALIGNMENT STATION (調整段站別)ASSEMBLY/PACKING PROBLEMmain boardMain BD(主機板)parts is not insert into MI MI未插入CRT boardCRT BD redundant parts in MI MI多件LED board LED BD components short each other 短路至其他部份others 其他moire水波紋ALIGNMENT PROBLEM 調整問題jitter/waggle畫面跳動/搖擺voltage adjust 電壓調整pix flash畫面閃爍function align 功能調整poor focus聚焦不良mechnical adjust 機構調整XRP CKT mal-functionXRP動作不良others 其他調整 F.W.T敲打不良OTHER PROBLEM 其他問題mute NG切換畫面不良beyond economic repair 非經濟維修other picture problem其他畫面不良difficult repair 修護困難red bias紅色偏壓engineer problem 工程問題green bias綠色偏壓no fail found 沒有不良發現blue bias藍色篇壓rework 重工red drive紅色驅動parts defect 零件不良green drive綠色驅動component defect 零件不良blue drive藍色驅動color change書色變色smear/tailing模糊/拖影cold solder/dry joint 冷焊/空焊different color at H&V line水平&垂直不同色older broken 錫點破裂impurity/doming色純度不良solder ball/solder short 錫球/錫短路blemish/phospher lost污點solder less 吃錫不良bri.too dark書面過暗others 其他raster show底色出現Hor. over/under scan 水平寬度過大/過小block L/O out of spec小方塊亮度超出規範poor hor.linearity 水平線性不良ABL L/O out of spec全白亮度超出規格hor.no sync 水平不同步poor contrast control對比控製不良hor fold over 水平反折poor bri. Control亮度控製不良poor hor center 水平中心不良poor G2 control G2控製不良poor hor phase 水平相位不良other color problem 其他顏色不良spot when power on/off 開/關機打點L/R output unbalance左右聲音輸出不平衡vert.collapse 一縱線L/R no put左右聲音不輸出vert over/under scan 垂直高度過大/過小Buzz 共振聲poor vert.linearity 垂直線性不良noise雜音vert.no sync 垂直不同步sound putput intermittent聲音輸出斷續vert.fold over 垂直反折Ear jack test failure耳機測試不良poor vert.center 垂直中心不良Microphone test failure麥克風測試不良vert.white bar 白Bar Other audio problem其他聲音不良retrace line 歸線NO power無電源hor.collapse 一橫線poor power saving省電功能不良geometry distortion 几何失真LED flash/power can't start-upLED閃爍&無法開機dog ear/top hook 扭曲/拉角smoke冒煙/跳火tilt 傾斜poor degaussing消磁不良no picture 無影像unit can't start-up起動不良pincushion distirtion 針墊不良hi-pot test failure高壓測試不良poor CG 收歛不良GND continue failure導通不良poor screen 畫面不良poor voltage電壓不良interference 干擾poor freg 除頻不良poor dymanic focus 動態聚集不良lack of manpowerpoor F/V adj 頻率轉換不良11.升降機故障High voltage leakage 高壓漏電lifter defectiveother power problem 其他電源不良12.ECN切入,REWORKGap 空隙engineering change notice reworkLoosen 松動13.設計問題,REWORKnot smooth 未平貼design problem, reworkpoor packing 包裝不良14.材料需全檢scratch/broken 損傷/破裂materials hold need sortingchange shape 變形body 毛邊operation 操作poor printing 印刷不良approve 贊成dirty 髒group 群.組(團体)other cosmetic problem 其他外觀不良leader 領班ICT TEST FAILURE ICT測試不良repair 修理micro ctrl latch-up 微電腦控制鎖住warehouse 倉庫micro ctrl data loss 微電腦控制資料遺漏trouble shooter 技術員DDC data error 寫入資料錯誤transfer 調動DDC data can't write-in 資料無法寫入manpower 人力function key can't work 功能鍵不動作DAY/NIGHT SHIFT 日/夜班(線)poor OSD display OSD顯示不良highlight 用強光照射(指提出重大事件)poor ATE ATE無法調net 淨效率Poor USB USB不良gross 毛效率goal 終點目標1.前殼不足total 總計的line stop/down time(front case shortage)workers 勞動者2.後殼不足urgent 緊急line stop/downtime(rear cover shortage)vertical 垂直3.材料不足horizontal 水平materials/parts shortage procedure 程序4.機構問題control run 小量試作mechanical design defective chassis 基板5.電氣問題inspection 檢驗technical design defective dynamic focus 動態聚焦6.加溫室故障tighten 提高規格burn-in room defective arching 跳火7.生產設備故障guide rail chassis 基板導軌production machine defective carton 紙箱;隔板類程序錯誤drop test 落下實驗program error support 支援(或支架)8.ATE故障combine 合併第 11 頁共 13 頁停線原因中英對照第 10 頁共 13 頁焊錫問題常用單詞SOLDERING PROBLEMATE defectiveseparate 分開9.包裝設備故障solution 對策packing machine defectiveaffirm 10.人員不足確定或確認(常用於新材料確認上)confirm Finance Department (FIN)加強;確認;批準(常用於對事情是否有確認)17.材料控制(物控)control panelMaterial Control (MC)(DAGGER機種的面板)18.生產控制(生管)follow-upProduction Control (PC)強制執行(對事情要確實實施)19.文件中心phase outDocument center 停用;或漸漸停產(用於機種或材料停用) 20.研發處color uniformityR/D Division=Research/Disign Division 色度一致性(指差異值) (a).電氣設計部brightness uniformity B/UElectrical design dept 亮度一致性(指百分比差異值)技術支援課T echnological support section Department 部門文件室1.產品工程部Document room Product Engineering Department(PE) (b).機構設計部2.測試工程部Mechanical design dept Test Engineering Department(TE) (c)專案管理部3.製造工程部Project Management DepartmentManufacture Engineering Department(ME)4.廠務工程部Factory Engineering Department(FE)5.資材部Material Department6.採購部Purchase Department7.人資部Human Resource Department8.自插部Auto Insertion Department9.品保部Quality Assurance Department10.進料品質管制In Coming Quality Control (IQC)11.製程品質管制In Process Quality Control (IPQC)12.出貨品質管制Out going Quality Control (OQC)13.品質工程Quality Engineering (QE)14.資訊部Management Information System(MIS) 15.制造部Manufacturing Department (MFG)16.財務部第 13 頁共 13 頁各部門中英文對照表第 12 頁共 13 頁。
工厂英语单词汇总(DOC)
1.机械与工厂英语组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs.inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS电源电压接柆键sheet metal parts 冲件plastic parts塑料件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床刨床miller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager |'depjuti| =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over 切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cut edges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line stretching, line pulling线拉伸engraving, to engrave刻印up siding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerization装箱quantity of physical inventory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts 良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkali dipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compression molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5t11T=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality audit 合格供货商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 参照件FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸12DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QS Quality System 品质系统ES Engineering Standarization 工程标准H Huston (美国)休斯敦IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板13PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算器辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C/T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PC14A/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 操作系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size------------------------------------------------------------------------------------------模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻15hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧16cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧销goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道17。
八年级英语上册Unit7单词汇总(新人教版)
even['iːvn]甚至；愈加
huan['hjuːən]人的；n.人；人类
servant['sɜːrvənt]仆人dangerous['deɪndʒərəs]危险的
already[ɔːl'redi]已经factory['fætri]工厂
八年级英语上册Unit7单词汇总（新人教版）
八年级英语上册Unit7单词汇总
Unit7
pollution[pə'luːʃn]污染；污染物
prediction[prɪ'dɪʃn]预测future['fjuːtʃər]未来
pollute[pə'luːt]污染environent[ɪn'vaɪrənənt]环境
planet['plænɪt]行星
earth[ɜːrθ] n.地球；泥土
plant[plænt] 种植，植物part[pɑːrt]参加，部分
peace[piːs]和平sy[saɪ]天空
playapart参与
astronaut['æstrənɔːt] 宇航员apartent[ə'pɑːrtənt]公寓房间
believe[bɪ'liːv]相信disagree[ˌdɪsə'ɡriː]不同意
shape[ʃeɪp]形状fall[fɔːl]倒塌；跌倒
possible['pɑːsəbl]可能的
obably['prɑːbəbli]大概；或许；很可能
holiday['hɑːlədeɪ]假日ord [ɜːrd]单词；
spacestation太空站
工业英语单词
(1048)able[`eibl]adj.能够abnormal[b`n:m l]adj.异常abort[`b:t]中断,停止absent[`bs nt]adj.不在的，缺少的acceleration[k.sel`rei n]n.加速，加速度access[`kses]vt.存取,进入，接近action[`k n].动作actuator[`ktjueit]n.操作(执行)机构,执行器address[`dres]地址adjust[`d st]调整，校正adjustable wrench活扳手adjustable[`d st bl]可调整的adjusting screw调整螺钉adjustment[`d stment]调节、调节装置air compressor空压机[k m`pres]压缩机air exhaust fan排气扇[ig`z:st]排气，抽完air[e]风，空气alarm[`lam]报警align[`lain]定位，对准，调整alternating current AC交流电[:l`t:n t]轮流，交替ambient temp环境温度ambient[`mbi t]周围的，环境的ammeter[`mit]n.电流表，安培计amp[mp]n.安培ampere[`mp]n.安培amplifier[`mplifai]n.放大器，扩音器analog input[`n l g]模拟量输入analog output模拟量输出analog signal模拟信号[`n l g][`signl]analog[`n l g]模拟analog-to-digital A/D模数转换[`did it l]angle valve角伐angle[`gl]角度application program应用程序[.pli`kei n]请求,应用arc[a:k]电弧，弧光area[`e ri]面积，区域arrester[e`rest]避雷器assemble line装配线，生产线[`sembl]assemble[`sembl]安装，组装asynchronous motor异步马达[ei`si n s] atomizing[`tm s.fi]雾化attention[`ten n]注意auto reclose自动重合闸autoformer自耦变压器automatic[.:t`tik]AUTO自动automatic voltage regulator自动调压器[`regjuleit] auxiliary[:g`zilj i]AUX辅助的avoid[`v id]避免,回避avometer[`v mit]万用表,安伏欧表计axis[`ksis]轴,轴线back pressure背压back up支持，备用back wash反冲洗baffle[`b fl]隔板bag filter除尘布袋balance[`b l ns]平衡,称，天平ball[bc:l]球bar[ba:]巴，条杆base[beis]基础、根据battery[`b t ri]n.电池bearing[`b ri]BRG轴承bell[bel]铃,钟(ring铃声，环)belt tension皮带张力[`ten n]belt[belt]带，皮带bi rate[bai reit]n.比特率binary[`bain ri]二进制，双bit[bit]比特（二进制）black[bl k]黑色blade[bleid]叶片bleed[bli:d]放气，放水blow[bl u]吹blown[`bl un]熔断的blue[blu:]蓝色boiler BLR[`b il]锅炉bolt[b ult]螺栓、拧螺丝boolean[`bu:li n]n.逻辑boost[bu:st]BST增压，提高boost pump BP升压泵bore[b:]孔，腔both[b]双方，两者都bottom[`b t m]底部bracket[`br支架，托架，括号brake[breik]刹车，制动器，闸break[breik]断开，断路、破裂、折断breaker coil跳闸线路breaker[`breik]断路器，隔离开关brown[braun]棕色brush[br]电刷，刷子bucket[`b kit]斗，吊斗buffer n.[`b f缓冲器1bump[b mp]碰，撞击burner[`b:n]燃烧器button[`b tn]按钮bypass/by pass BYP旁路byte[bait]字节（八位）cabinet[`k binit]厨柜，机箱、柜cable[`keibl]电缆calculator[`k lkjuleit]计算器caliber[`k lib]管径、尺寸、大小cam[k m]凸轮cancel[`k ns l]取消、省略capacitance[k`p sit ns]n.容量，电容capacitor[k`p sit]n.电容器＝capacitator card[ka:d]（电子）板、卡carton[`ka:t n]纸板箱casualty[`k ju lti]人身事故、伤亡、故障center[`sent]中心central control room中控室central processing unit CPU中央处理器centrifugal fan离心风机centrifugal[sen`trifjug]离心的change[t改变character[`k rikt]字符charge indicator验电器、带电指示器:d充电，电荷chassis earth机壳接地chassis[`si]底座、机壳check[t ek]检查chimney[`t mni]烟囱、烟道circuit[`s:kit]n.电路circuit breaker电路断路器circuit diagram电路图[`dai grcircuitry[`s:kitri]n.电路，线路circulating water pump循环水泵circulating循环[`s:kjuleiti]clamp[kl mp]夹具、钳class of insulation绝缘等级[.insju`lei n]class[kla:s]类、等级、程度clean[kli:n]清洁的、纯净的cleanse[kle净化、洗净、消毒CLEARING OF F AULT故障清除clockwise[`kl kwaiz]顺时针、右旋的clog[kl g]障碍，塞满，粘注close[kl uz]关闭closed-loop闭环[lu:p]coarse[k:s]粗的、不精确的code[k ud]代号、密码coder[`k ud]编码器coil[k il]n.线圈cold[k uld]冷,冷的，感冒collect[k`lekt]收集colour[`k l]颜色command[k`ma:nd]命令、指挥communication[k.mju:ni`kei通信、通讯compensation[k mpen`sei n]补偿，矫正component[k m`p un nt]元件compress air压缩空气[]compress[k m`pres]压缩compressor[k m`pres]压缩机computer[k m`pju:t]计算机condensate[k n`denseit]冷凝、使凝结condition[k n`di n]条件、状况、环境conduct[`k nd kt]传导conductivity[.k nd k`tiviti]导电率conductor[k n`d kt]n.导体，导线configure[k n`fig]组态congealer[k n`d i:l]冷却器、冷冻器connect[k`nekt]连接connection[k`nek n]联接connector[k`n kt]联接器、接线盒console[k n`s ul]控制台constant[`k nst nt]恒定的contact[`k nt kt]n.接触,触点,vt.接触,联系contact to earth接地、触地、碰地[:]contact[`k nt kt]触点contactor[`k nt kt]（电流）接触器、触头continuous[k n`tinju s]连续的control[k n`tr l]CNTR/CNTPL控制control panel控制盘[`p nl]面板，仪表板，屏幕control valve调节阀[v lv]controller[k n`tr ul]控制器convert[k n`v:t]n.转换vt.使转变，转换….conveyor[k n`vei]传送带，输送机cooktop[`kukt p]n.炉灶cool[ku:l]冷的cooler[`ku:l]冷却器cooling fan冷却风机[f n]cooling tower冷却塔[`tau]塔，城堡cooling water pump冷却水泵cooling[`ku:li]冷却copy[`k pi]拷贝core[k:]铁心、核心、磁心2correct[k`rekt]正确的,改正correction[k`rek n]修正、改正corrosion[k`r u n]腐蚀counter[`kaunti]n.计数器couple[`k pl]CPL联轴器curdle[`k:dl]凝固currency[`k r nsi]流动、流通current[`k r nt]n.电流，水流、当前、气流current transformer CT电流互感器[tr ns`f:m]cursor[`k:s]光标curve[k:v]曲线cutter[`k t]切削工具,刀具ccycle循环、周期、周波cylinder[`silind]CYL汽缸，圆柱体cymometer[sai`m mit]频率表，频率计damage[`d mid]损坏、破坏danger zone危险区[z un]danger[`deind]危险、危险物dangerous[`deind r s]危险的dank[d k]潮湿data base数据库[beis]底部，基层，灯座data pool数据库[pu:l]data[`deit]数据deactivate[di:`ktiveit]使无效dead band死区[ded][b nd]区，队debugging[di:`b gi]n.调试deceleration[di:.sel`rei n]n.减速，减速度decrease[di:`kri:s]DEC减少deep[di:p]深度、深的、深default[di`f:lt]n.默认(值),缺省(值)degree[di`gri:]度、等级delay time延时[di`lei]延迟，滞后relay[`ri:lei]继电器delay[di`lei]延迟，滞后delete[di`li:t]删除，作废defective[di`fektiv]有缺陷的，损坏，次品，不完全description[dis`krip n]说明、描述detect[di`tekt]发现、检定detector[di`tekt]检测器，探测器deviate[`di:vieit]背离、偏差device[di`vais]设备、仪器，装置diagnosis[.dai g`n usis]诊断diagram[`dai gr m]图形、图表diameter[dai`mit]直径dielectric[.daii`lektrik]介质、绝缘的diesel generator柴油发电机[`di:z l][`d en reit]发电机，振荡器differential[.dif`ren]差别的，差动的，微分differential pressure DP/DSP差压[`pre]digital input/output数字量输入／输出[`did itl]数字的，数字digital signal数字信号[`did itl][`signl]digital[`did itl]数字的digital-to-analog D/A数／模转换[`l g]direct current DC直流（电）[di`rekt]直接的disassembly[.dis`sembli]拆卸disaster shutdown事故停机[`tda n]停工（机），关机disaster[di`za:st]事故、故障discharge排除、放电、卸载disconnect switch隔离开关disconnect断开,分离disconnector隔离器、隔离开关discrete[dis`kri:t]adj.不连续的,离散的discrete input开关量输入discrete output开关量输出disk[disk]磁盘diskette[dis`ket]磁盘，磁碟display[di`splei]显示、列屏dissipation[.disi`pei n]n.分配，分发distance[`dist ns]距离，间隔distilled water DISTL WTR蒸馏水[dis`tild]由蒸馏得来的distributed control system DCS集散控制系统distributed[dis`tribju:tid]分布的distributing board配电盘[dis`tribju:ti][b:d]double[`d bl]两倍的，双重的dowel pin定位销[`dau l]销子[pin]down[daun]向下的,向下download下载downtime停机时间drain DRN疏水、排放drawing[`dr:i]画图.制图,图样、牵引drill[dril]钻孔、钻头、钻床drive nail钉钉子drive[draiv]驱动、强迫drop[dr p]滴，点滴，落下dry[drai]干、干燥duct[d kt]风道、管道dust catcher除尘器、吸尘器[`k t]捕捉器dust[d st]灰尘duty[`dju:ti]责任,义务dynamic[dai`n mik]动态的dynamometer[.dain`m mit]功率表earth connector接地线、接地[:][k`n ktearth fault接地故障[f:lt]3earth lead接地线、接地[li:d]引线，领导earth大地[:]eccentricity[eksen`trisiti]偏心、扰度edit[`edit]编辑efficiency[i`fi ns]效率ejected[i`d ekt]喷射，驱逐，被放出的ejection[i`d ek n]弹出，排出，喷出，喷射electric failure触电[i`lektrik]电的[`feilj]故障，失败electric spark电火化[spa:k]electric[i`lektrik]电的、电动的、导电的electrical machine电机[m`i:n]机器，机械electrical service供电[`s:vis]维修，服务，管理electrical[i`lektrikl]电的、电气的electric-hydraulic control电／液控制[hai`dr:lik][k n`trol]electrician[ilek`tri n]电工electrode[i`lektre d]电极electronic[ilek`tr nik]电子的、电子学的electrostatic[i`lektr u`st tik]静电的electrotechnics[i`lektr u`tekniks]电工学、电工技术element[`elim nt]元件、零件、单元elevator[`eliveit]n.电梯,升级机emergency[i`m：d nsi]EMERG紧急事故empty[`empti]排空enable[i`neibl]使能够，允许enclosure[in`kl u]n.密封，外壳，包围encoder[in`k ud]编码器end cover端盖end末端、终结energy meter电度表energy[`en d i]能、能量engineer[.end i`ni]工程师enter[`ent]开始、使进入entry[`entri]输入equipment[i`kwipm设备error[`er]错误escape valve安全阀[is`keip]event[i`vent]事件exceed[ik`si:d]超过excess[ik`ses]超过、过度exciter[ik`sait]励磁机exit[`eksit]出口expansion[iks`n n]EXP膨胀explosion[iks`pl u n]爆炸external[eks`t:nl]外部的、表面的extra-high voltage超高压[`ekstr]额外的，特大的factor[`f kt]因素、因数factory[`f kt ri]工厂、制造厂failure[`feilj]FAIL失败,故障false[f:ls]假的、错误的fan[f n]风扇、风机fault[f:lt]故障faultless[`f:ltlis]没有缺陷、完美的faulty operation误操作[`f:lti][.p`rei n]运算，工作features[`fi:t]特点feed[fi:d]馈、供给feedback[`fi:db k]反馈fiber optic光纤[`faib]光纤，纤维[`ptik]光学上的，视觉的field[fi:ld]n.现场，原野file[fail]文件、锉刀fill[fil]装填filter[`filt]n.过滤器，滤波器，滤网，filter differential pressure FILTR DP滤网压差final[`fain]最后的fire pump消防水泵fire[`fai]燃烧、火焰fireproof[`fai pru:f]防火的、阻燃的fixed[fikst]固定的、固定、确定、保护屏flank[fl k]侧翼、侧面flash lamp闪光灯flash light闪光flash[fl]闪光、闪烁、闪蒸float-charge浮充电[fl ut]浮动[t a:d]充电，电荷flow[fl u]流量、流动flowmeter[`fl umi:t]流量计flue gas烟气[g s]气体，煤气，毒气，汽油flue[flu:]烟道fluid[`fluid]液体flux[fl ks]n.流量，通量forbid[f`bid]禁止force draft fan送风机[dr:ft]通风force[f:s]强制form[f:m]形式、形状、形成、构成format[`f:m t]形式、格式frequency[`fri:kw nsi]频率friction[`frik n]n.摩擦，摩擦力from[fr m]从、来自、今后full speed额定频率fully[`fuli]充分的、完全的fume[fju:m]烟，冒烟function[`f k n]功能fuse holder保险盒[`h uld]4fuse[fju:z]保险丝、熔断器fusible cutout熔断开关[`fju:z bl]溶解的,可融的[`k taut]断流,保险装置gauge[ed]仪表、标准gear pump齿轮泵[i][p mp]gear shift housing变速箱[ift]换挡，变化[`h uzi]外壳，套gear[i]齿轮gearbox齿轮箱general control panel总控制屏[`d en r l]普通的，全面的，综合的generator[`d en reit]n.发电机gland seal轴封[l nd]填料函盖，密封压盖[si:l]封，密封，填料glass-paper砂纸go on继续goal[ul]目的、目标graphics[`r fiks]调节阀grease[ri:s]图形green[ri:n]绿色ground[ra nd]地面，场所、接地earth[:]地球，接地、大地，泥土guide[aid]领路人、向导half[h:f]一半、一半的halt instruction停机指令[h:lt]停机,中断,暂停[in `str k n]halve[ha:v]vt.二等分，平分hammer[`h m]锤子hand[h nd]手，指针handle[`h ndl]vt.触摸,运用,买卖,处理,操作vi.搬运,易于操纵handwheel[`h ndwi:l]手轮，驾驶盘hardware[`h:dw]硬件havoc[`h v k]n.严重破坏vt.损害heat[hi:t]热、加热heater[`hi:t]加热器heating[`hi:ti]加热,供暖hertz[`h:ts]HZ赫兹high pressure HP高压history[`hist ri]历史hold[h uld]保持hopper[`h p]漏斗、料斗hose[h uz]软管、水龙带hot circuit通电线路[`s:kit]hot start热态启动[st:t]hot[h t]热的,热情的，辣的hydraulic[hai`dr:lik]水力的，液压的，油压的，水压的I/O point输入/输出点inboard[`inb:d]内侧idle[`aidl]空闲的，空载的、无效的ignitor[ig`nait]点火，点燃，点火器impedance[im`pi:d ns]阻抗import[im`p:t]进口、输入、引入impulse[`imp ls]脉冲、冲击、冲量inch[int]IN英寸inching[`int i]缓动、点动increase[in`kri:s]INC增加increment[`inkrim nt]增量，加1，递增index[`indeks]索引、指标，指针，指数indicate[`indikeit]指示，显示，表明indicator[`indikeit]指示器inductance[in`d kt ns]电感,自感应induction motor异步电动机[in`d k n]感应[`m ut] inductive reactance感抗[in`d ktiv]电感的，感应的[ri`kt ns]电抗inductor[in`d]n.电感器，感应器inhibit[in`hibit]禁止,抑制，约束init初使化initial[i`ni l]初始的，最初的inlet[`inlet]入口input/output I/O输入／输出insert[in`s:t]插入inside[`in`said]内侧、内部inspection[in`spek n]观察、检查inspector[in`spekt]n.检测install[in`st:l]安装instruction[in`str k n]n.指令，指导，指示，说明书，instrument panel仪表盘[`p nl]instrument[`instrum nt]仪器insufficient[.ins`fi nt]不足的，不够的insulate[`insjuleit]绝缘、隔离insulation[.insju`lei n]绝缘insulator[`insjuleit]n.绝缘体integer[`intid]整数integral[`inti r l]积分,积分的interface[`int.feis]n.分界面,界面,接口interface[`int.feis]接口interference[.int`fi r ns]干扰、干涉intermediate relay中间继电器[.int`mi:dj t]中间的，中级，中频internal[in`t:nl]内部的,内部interrupt[.int`r pt]中断into[`intu]向内、进入,到…里，进入到…之内inverter[in`v:t]逆变器、反相器、非门isolator[`ais leit]隔离器、刀闸，分离器，绝缘5体job[d b]工作jumper[`d mp]跳线、跨接junction box接线盒[`d k n]key[ki:]键销、钥匙、键槽keyboard[`ki:b:d]键盘kilovolt-ampere KV A千伏安[`kil v lt`mpe] kink[ki k]弯曲、缠绕knack[n k]技巧、窍门、诀窍knife-switch闸刀开关label[`leibl]标号、标签，商标，标志laboratory[l`b r t ri]实验室ladder diagram梯形图[`l d][`dai gr m]ladder logic Diagram逻辑梯形图[`l d ik][`dai gr m] ladder[`l d]梯子、阶梯lamp[l mp]n.灯、光源last[la:st]最后的,末尾的leak[li:k]泄漏，漏，漏洞（动词）leakage[li:kid]n.漏，泄漏，渗漏least[li:st]最少的、最小的left[left]左length[le]长度level[`levl]液位、水平lever[`li:v]杆,杠杆,控制杆lifebelt[laifbelt]安全带、保险带lift[lift]提、升light run空转[lait][r n]light[lait]光,灯,轻,淡,日光,光亮,点,点燃,照亮lightning[`laitni]雷电limit[`limit]LMT极限、限制limit switch[`limit]限位开关limiter[`limit]限制器、限位开关line[lain]线、直线list[list]列表、目录liter[`li:t]公升little[`litl]小的，少许，少的load[l ud]n.负荷，负载load thrown on带负荷[r un]local attendant现场值班员[`tend nt]维护人员，值班人员，服务员local repair现场检修[ri`p]修理，修补local[`l uk l]当地的,局部，本地location[l u`kei n]位置，定位，单元，场所lock[l k]闭锁、密封舱、固定logger[`1]记录器、拖车logic[`l d ik]逻辑long[l]长loop[lu:p]环、回路loose[lu:s]松的、不牢固的loosen[`lu:sn]松开、松动loss[l s]损失、减少low[l u]低lower[`l u]较低的、降低low-half下半[h:f]lub oil pump润滑油泵lub oil润滑油lubricate[`lu:brikeit]LUB润滑machine[m`i:n]机器,机械magnet[`m nit]磁main wire电源线[`wai]main[mein]主要的,主群组maintain[men`tein]维修、维持、保养maintenance manual检修手册[`m nju l]maintenance[`meintin ns]维护、维护，检修、小修make[meik]制造,是成为make sure确定[u]的确，对…有把握make up补充（补给）malfunction[m l`f k n]故障,出错、误动、失灵management[`m nid m nt]管理、控制、处理man-machine interaction人机对话[m n][m:`i:n][.int`k n]man-machine interface MMI人机接口[`int.feis]界面，接口manometer[m`n mit]压力表manual reject MRE手动切换[ri`d ekt]拒绝，排斥manual[`m nju l]手动、手册manual/Auto station M/A STA TION手动／自动切换站mark[m:k]型号、刻度、标志、特征master control room主控室、中央控制室[k n`tr l]master[`m:st]主人，主要，控制，师傅，正版material[m`ti ri l]n.材料，原料maximum[`m ksim m]最大,最大值，最高，mean[mi:n]平均，平均值、中间的measure[`me]度量、测量，量，尺寸mechanical trip vlv机械跳闸阀[mi`k nikl][trip]脱扣，解扣mechanical[mi`k nikl]机械的、力学的mechanism[`mek niz m]机械、力学、方法、装置、机构medial[`mi:dj l]中间的、平均的medium[`mi:dj m]中间的、中等的、装置、介质、工质melt[melt]溶解，熔化memory[`mem ri]存储,存储器，记忆menu[`menju:]n.菜单6metal[`metl]金属meter[`mi:t]n.仪表，米，表meter switch仪表开关method of operation运行方式[.p`rei n]操作，运转method[`me d]方法、规律、程序microphone[`maikr f n]麦克风、话筒,传声器，扩音器microprocessor[maikr u`pr uses]n.微处理器middle[`midl]MID中间的,中间，当中，中型mill[mil]磨、磨粉机、压榨机，铣刀mind[maind]头脑、精神、介意minimum[`minim m]最小的minor overhaul小修[main]次要，副修科目[.auv`h:l]检修，大修minute[mai`nju:t]分钟misfill误装mishandle[`mis`h ndl]胡乱操作、误操纵misread[mis`ri:d]错读miss[mis]过错，避免，小姐，姑娘，故障，失败miss operation误动作、误操作[.`rei n]mistake[mis`teik]错误、事故mixer[`miks]n.搅拌器，混合器,混频器modem[`m ud m]调制解调器modify[`m difai]修改、更改modulating valve调节阀[`m djuleit][v lv]module[`m dju:l]n.模块，组件，模数moisture[`m ist]湿度、湿汽mold[m uld]模具monitor[`m nit]n.监听器，监视器，监控器vt.&vi.监控month[m n]月more than超过[m:]更多的[n]与…相比较，比motor MTR马达[`m ut]motor winding电动机组绕组[`waindi]绕组，线圈，绕，缠mount[maunt]安装、固定mouse[maus]鼠标move[mu:v]移动multimeter[`m ltimit]万用表nail[neil]钉子、钉钉子naught line零线[`n:t]零，无neck[nek]颈，管颈needlepoint vlv针阀[`ni:dlp int]negative pressure NEG PRESS负压negative[`neg tiv]负的network[`netw:k]网络neutral line中性线[`nju:tr l]中性的newly[`nju:li]最近,重新、新地nipper[`nip]钳子、镊子noise remove消音器[n iz][ri`mu:v]noise[n iz]噪音no-loading空载nominal power额定功率[`n minl]标称的，额定的[`pau]nominal[`n minl]标称的、额定的normal closed contact常闭触点[`k nt kt]触头，触点，接点normal[`n:m l]正常的、常规的normally[`n:m li]正常地not available无效、不能用[`veil bl]可用的，有用的nozzle[`n zl]喷嘴number[`n mb]数字、号码、数目nut[n t]螺母、螺帽occur[`k:]发生ohm[um]n.欧姆oil breaker油开关[`breik]oil gun油枪[g n]oil level机油平面[`levl]oil[il]油oiler[`il]注油器,油商oilless[lles]缺油的on/off开／关online[nlain]联机的，在线的open circuit开路[`up n][`s:kit]open-loop开环[lu:p]operating panel操作盘[`p reiti][`p nl]operation[.p`rei n]操作、运行operational log运行记录[.p`rei n][l]operator keyboard操作员键盘[`ki:b:d]operator station操作员站[`stei n]operator[`p reit]操作员option switch选择开关optional[`p n l]可选的,选择orbit[`:轨道，轨迹orientation[.rien`tei n]方位，定向，定位original[`rid n l]初始的、原始的out出、出口outboard[`autb:t]外侧的outage[`autid]断电，停机，出故障outlet[`autlet]出口output[`autput]产量、产品、输出oven[`vn]n.烤箱over current过流[`k r nt]over loading过载[`l udi]over voltage过压[`v ltid]over[`uv]结束,上面的,过分的7overcool[`uv ku:l]过冷却overflow[`uv`fl u]溢流overhaul[.uv`h:l]大修,检修overhead[`uv hed]顶部,高空，架空overheat[.uv`hi:t]使过热overload[`uv`l ud]n.过载overload protection过载保护[`uv`l ud][pr`tek n]package[`p kid]组件、包,插件packaging[`p kid i]n.包装panel[`p nl]屏、盘parameter[p`r mit]参数part[p:t]部分、部件password[`p:sw:d]口令,密码peak[pi:k]峰值percent[p`sent]PCT百分数percentage[p`sentid]百分比perfect[`p:fikt]完全的、理想的performance[p`f:m ns]完成、执行、性能periodic inspection定期检查[in`spek n]periodic[pi ri`dik]周期的、循环的peripheral equipment外围设备[i`kwipm nt] peripheral[p`rif r l]周围的，外围设备，周边的permanent[`p:m n nt]永久的、持久的permit[p`mit]允许PG编程器phase not together缺相、失相[feiz]相[t`e]共同phase[feiz]PH阶段、状态、方面、相phase sequence相序[`si:kw ns]次序，顺序，时序phase voltage相电压phase-failure protection断相保护[`feilj]phase-in同步photoelectricity[.f ut uilek`trisiti]光电piezometer[.pai`z mit]压力计pilot[`pail t]导向、辅助的、控制的pipe[paip]管、管道plan[pl n]计划plant[pl:nt]工场、车间plastic[`pl stik]塑料PLC(programmable Logic Controller)可编程序逻辑控制器pliers[`plai z]钳子、老虎钳plug socket插座[`s kit]plug[pl]塞子、栓、插头plus[pl s]加pneumatic[nju`m tik]气动的point[p int]点pointer[`p int]指针，指示器pole[p ul]极、柱，极点，电极，电杆pollution[p`lu:n]污染portion[`p:n]一部分position[p`zi n]POS位置potential[p`ten l]电势，电位potential transformer PT电压互感器[p`ten l][tr ns`f:m]power failure停电[`pau][`feilj]故障，失败power[`pau]PWR功率、电源,能力，动力PPI(point-to-point Interface)点对点接口preblow预吹preferential[.pref`ren l]n.优先的，优先权perform[p`f:m]预先形成，预制，预成型坯，粗加工的成品preheat[`pri:hi:t]预热preheater[`pri:hi:t]预热器preliminary[pri`limin ri]准备工作present[pri`zent]出现preset[`pri:`set]预设、预置press[pres]压，按，压力pressure[`pre]PRES压力primary[`praim ri]初级的、一次的principle[`prins pl]原理、原则printer[`print]打印机probe[pr ub]探头process[pr`ses]过程、方法production[pr`d k n]生产、产品、作品program[`pr u r m]程序programmable[`pr ugr m bl]adj.可设计的，可编程的prohibit[pr`hibit]禁止proportional/integral/derivative PID比例／积分／微分protection[pr`tek n]PROT保护、预防protocol[`pr ut k l]n.协议pull[pul]拖,拉pulse[p ls]脉冲、脉动pump body泵体pump[p mp]泵purge[p:d]净化、吹扫push and pull switch推拉开关push button按钮push[pu]推pushbutton[pu`b tn]n.按钮pyod[`pai d]热电偶quality[`kw liti]质量quit[kwit]停止、离开、推出8rack earth机壳接地[r k]机架，机柜，导轨[:] radiation fin散热片[.reidi`ei n]辐射，发散fin]散热片radiator[`reidieit]n.散热器，冰箱raise[reiz]升高range[reind]范围、量程rate[reit]速度，速率rated power[`reitid]额定功率rated[`reitid]额定的、比率的ray[rei]光线、射线read out读出、结果传达reading读数real time实时的[`ri:l]receive tank回收箱、接收箱[ri`si:v][t k]receive[ri`si:v]收到，接到，接收，接待recipe[`resipi]处方、配方reclosing重合闸recovery time恢复时间[ri`k v ri]recovery[ri`k v ri]恢复、再生rectification[.rektifi`kei n]整流、检波、调整rectifier[`rektifai]n.整流器，矫正器red红色reduction[ri`d k n]还原、缩小、降低redundancy[ri`d nd nsi]冗余、多余reference[`refr ns]REF参考、参照、证明书reflux[`ri:fl ks]倒流、回流register[`red ist]寄存器regulate[`re juleit]调节、控制relay[`ri:lei]n.继电器release[ri`li:s]释放reliability[i`biliti]可靠性、安全的relief[ri`li:f]去载、卸载、释放、解除relieve valve安全阀、减压阀[ri`li:v][v lv]remove除去、拆卸renewal[ri`nju l]更新、更换repair[ri`p]修理repairer修理工、检修工repeat[ri`pi:t]重复、反复replace[ri`pleis]重新、启动、更换、替换replacement parts备件、替换零件[ri`pleism nt][p:t] request[ri`kwest]REO请求require[ri`kwai]要求reserve parts备件[ri`z:v]reserved[ri`z:vd]备用的reset[`ri:set]复位resist[ri`zist]n.阻抗resistance[ri`zist ns]n.电阻、阻抗resolution[.rez`lju:n]n.分辨率response[ris`p ns]响应restart[ri:`st:t]重新启动retighten[ri`tait n]重新紧固retract[ri`tr kt]可伸缩的、缩回return oil回油[ri`t:n]return[ri`t:n]返回reverse rotation反转[ri`v:s]rig[ri]安装、装配、调整right[rait]右right-of-way公用线路ring[ri]环roller[`r ul]滚筒、辊子rotary switch转换开关[`r ut ri]rotate[r u`teit]旋转rotation[r u`tei n]旋转，转动，回转rotor[`r ut]转子routine[ru:`ti:n]例行的、日常的routing inspection日常检查、日常检测[in`spek n] routing maintenance日常维护[`ru:ti][`meintin ns] rubber[`r b]橡胶run back返回run运行safe[seif]安全的、可靠的、稳定的safety cap安全帽safety[`seifti]安全sample[`s mpl]取样、举例sampling[`s:mpli]采样、抽样、取样saw[s:]锯scale[skeil]刻度、衡量、比例尺、测量、铁锈水垢scan[sk n]扫描schedule[`ekju:l]时间表、计划表screen[skri:n]]屏幕screw driver螺丝刀screw socket螺口插座screw[skru:]螺杆、螺丝、旋转seal[si:l]密封search[s:t]寻找、查找second[`sek nd]秒、第二seep[si:p]渗出、渗漏seepage[`si:pid]渗漏现象select[si`lekt]选择selector[si`lekt]选择器self-hold[self][h uld]自保持self-running自启动send[send]发送，寄，发射9sensor[`sens]传感器sequence[`si:kw ns]顺序、序列service manual维修说明书series[`si ri:z]n.连续，串联service[`s:vis]维修.保养.服务、伺服servo[`s:v u]伺服servomotor[`s:v u.m ut]伺服电机set up安装、调整、建立set[set]设定shaft[:ft]轴、手柄、矿井shake[eik]摇动、振动shield[i:ld]屏蔽shift[ift]值、替换shock[k]震动,使受电击short circuit短路short[:t]短的、短路、使短路should[ud]应该,将要show[u]展览,显示,指示shut off关闭[t]关闭，关上shut[t]关上，更加shutdown[`tda n]停止、停机siccative[`sik tiv]干燥剂,使干燥的，side[said]侧边siemens[`si:m z]西门子sifter[`sift]筛子、滤波器sign[sain]标记、注册signal lamp信号灯signal[`si nl]信号,发信号silencer[`sail ns]消音器simulation[.s imju`lei n]n.仿真，模拟simulator[`simjuleit]仿真机single blade switch单刀开关[bleid]刀刃，刀片single[`si l]单个的、个体的site[sait]现场size[saiz]尺寸、大小skip[skip]空指令、跳跃smoke[sm uk]烟、冒烟smokes-stack烟囱[st k]烟囱，堆，堆栈smooth[smu:]平滑的、光滑的socket wrench套筒扳手socket[`s kit]插座software[`s ft]软件solenoid[`s ulin id]电磁线圈solid wrench呆扳手solid[`s lid]固体、坚固的、固体的source[s:s]源、电源spanner[`sp n]扳手spare[sp]备用的、空余的spare parts备件、备品spark[sp:k]火花special tool专用工具special[`spe l]特别的、专门的specification[.spesifi`kei n]技术要求，说明书speed[spi:d]速度spray nozzle喷嘴[sprei]喷雾，喷射spring clutch弹簧离合器[kl]离合器spring[spri]弹簧、春天stack[st k]烟囱,堆栈stall[st:l]停车、阻止standard[`st nd d]标准standby[`st ndbai]备用、待机star[st:]星、星形连接start up启动start[st:t]启动、开始starter[`st:t]n.启动器，启动钮starting conditions启动条件[`sta:ti]启动，开始，出发start-up sequence启动程序[`si:kw ns]程序，次序，顺序，序列state[steit]状态statement[`steitm nt]声明、语句station[`stei n]站、台，岗位，身份，地点，发电厂，位置stator coil定子线圈stator core定子铁芯[k:]stator[`steit]定子status display状态显示status[`steit s]状态stability[st`biliti]稳定性steam[sti:m]STM蒸汽step[step]步，步幅step-by-step步进式，逐步，按部就班的step-by-step motor步进电动机step-down transformer降压变压器step-up transformer升压变压器still[stil]仍然，还，更stop[st p]停止storage battery蓄电池storage[`st rid]储存strainer[`strein]滤网,过滤器streamline[`stri:mlain]流水线stretching[`stret i]拉伸，伸长suction pump真空泵[`s k n]吸入，抽气，superheater[`sju:p hi:t]过热器10supply[s`plai]供给support[s`p:t]支持、支撑sure[u]确信的、可靠的switch[swit]n.开关，电闸switch blade开关闸刀[bleid]刀刃，刀片switch[swit]开关、切换switching off断开[`swit i]switching on接通switching push button开关按钮symbol[`simb l]符号synchro[`si kr u]同步，同步机synchronization[.si kr nai`zei n]同步synchronizer[`si kr naiz]同步器syren[`sai r n]汽笛、报警器syringe[`sirind]注油器system unit主机system[`sist m]系统tab[t b]表格,制表tachogenerator[`t k`d en reit]测速发电机tandem[`t m]串联tank[t k]箱temperature compensation温度补偿[k mpen`sei n] temperature[`temprit]温度tensile[`tensail]拉力的、张力的tension[`ten n]压力、拉紧、张力terminal[`t:minl]n.终端，接线端，电路接头test[test]检测、试验tester[`test]检测者、检测器text[tekst]出口thermal conduction热传导[`:m l]热的[k n`d k n]传导，导电thermal couple热电偶[`k pl]电偶，偶合thermal[`:m l]热的，热量的，由热驱动的thermometer[`m mit]温度计thermostat[`:m st t]自动调温器，稳定调节装置，恒温器throttle[`r tl]节流thrust[r st]冲击、推力thyristor[ai`rist]晶闸管tight[tai]紧密的、紧固的tighten[`tait n]扣紧、变紧time-lag relay延时继电time-lag时间间隔timing[`taimi]n.计时器,定时器toggle switch[`togl]拨动开关token[`t uk n]标志tong-test ammeter钳式电流表[t]钳tool box工具箱tool[tu:l]工具torque wrench扭力扳手torque[t:k]扭矩、力矩total[`t utl]总计的training officer培训主管[`treini]训练，练习transducer XDUCER传感器、交流器，变频器transfer转换transformer XFORMER变压器，传感器，发送器transmission传输transmitter XMItEER变送器transwitch可控硅开关travel[`tr vl]过程、运转、进行、移动trigger[`tri]触发器trip[trip]跳闸、断开tri-way vlv三通阀trouble[`tr bl]事故、故障、干扰true[tru:]真实的、调整、校正try[trai]尝试试图努力tune[tju:n]调节,曲调tuning[`tju:ni]调谐turn[t:n]转动、转向twist drill麻花钻[twist]扭转，扭曲type[taip]类型、标志unbolt[`nb ult]取下螺栓unclean[`n`kli:n]脏的underground cable地下电缆[`nd地下的under voltage欠压、电压低uninterrupted power supply UPS不间断电源[`nint`r ptid]连续unit[`ju:nit]单元、单位unload[`n`l ud]减负荷,卸载，放电unlock[`n`l k]打开、解锁、释放unprotected[`npr`tektid]未保护的、无屏蔽的untight[n`tait]松动的up向上update[p`deit]更新、修改、校正upgrade[`p reid]升级(优先级）提高/改进up-half上部、上半[h:f]upper[`p]上部的，上面的use[ju:s]使用,利用user[`ju:z]用户，使用者uninsulate[n`insjuleit]不绝缘vacuum[`v kju m]n.真空，空间，真空吸尘器vacuum pump真空泵valid[`v lid]有效地、正确11valley load低谷负荷[l ud]负载，负荷value[`v lju:]数值valve[v lv]n.VLV阀valve disk阀芯valve seat阀座vane[vein]叶片variable[`v ri bl]变量variator[`v rieit]变化器，变速器v-belt三角皮带[belt]ventilation[venti`lei n]VENT通风ventilator[`ventileit]通风机，风扇，通风设备vertical[`v:tik l]VERT垂直的vessel[`vesl]容器vibrate[vai`breit]（使）震动，摇摆vibration[vai`brei n]振动viscosity[vis`k siti]粘度video display unit VDU显示器[`vidi u][di`splei] vision[`vi n]视觉，视力，显示visor[`vaiz]护目镜、观察孔voltage[`vaultid]n.电压，伏特数voltage drop电压降[`v ultid][dr p]滴，落下voltage transformer电压互感器voltmeter[`v l t.mi:t]n.电压表volume[`w lju:m]容积、体积wall temp壁面温度[w:l]墙，墙壁warning[`w:ni]报警wash[w]洗washer[`w]垫圈、补垫waste[weist]浪费、废物watch[w t]手表,注视watchdog[`w t d]看门狗water[`w:t]WTR水wattage[`w tid]n.瓦特数wear[wi]穿,磨损weather[`we]天气week[wi:k]星期、周weight[weit]重量，重力weld[weld]焊接wheel[wi:l]轮，车轮，轮子，转盘while[wail]一会儿white[wait]白色winch[wint]卷扬机.windings[`waindi]绕组windows[`wind z]窗口wire[`wai]电线、金属丝、接线without[wi`aut]没有,不wood[wud]木、木制的word[w:d]字，词work[w:k]工作workshop[`w:k p]车间，工场worm drive蜗杆转动worm[w:m]涡轮、螺杆wrench[rent]扳手，拧wrong[r]错误的、失常的wye Y形接法year[j]年yellow[`jel u]黄色zero drift零点漂移[drif t]zero[`zi r u]零,零位zone[z un]区、层、带12。
工厂常用英语单词一览表
Testing words
制品檢驗 examination 綜合抵抗 termination resistance 耐電壓 dielectric withstanding voltage 絕緣抵抗 insulation resistance 振動(低周波） vibration （low frequency) 振擊 physical shock 耐久性 durability 耐熱性 resistance to re-flow soldering heat 熱振擊 thermal shock 溫濕度 temperature humidity cycling 公差 tolerance 熱電偶 thermocouples 烤爐 oven
人事部 personnel Dep. 行政部 administration Dep. 品管部 quality control Dep. 工程部 engineering Dep. 采購部 purchase Dep. 財務部 accounting Dep. 業務部 Sales Dep. 關務部 Custom service Dep. 生產部 manufacturing Dep. 文件中心 document control center 資訊部 manage information system 品 保 quality assurance 插件部 auto-insertion (AI) 制程品質管制： in process quality control (IPQC) 進料品質管制： incoming quality control ( IQC) 出貨品質管制：outgoing quality control (OQC)
工廠常用英語單詞一覽表
工厂工业技术常用英语单词词汇
material material approve material return maylar(c apacitor )
MC:mater ial control MCR:mech anical changed request MDR:mate rial defeat report ME:manuf acture engineer ing measurem ent MEB(capa citor)
name
N
plate
裝否飾定片的
negtative
反向的負
shortage
淨需求
netwwork
綱新路機種一
mNoGd=eNlOT
線檢查表
GOOD
非良品
notice
通知
NUT
螺帽
obligati on
ohm
O 義務 責 任 歐姆(電 阻單位)
order
靜電
detail
明細
disable
預定的
deviate
偏差
excess
過剩
diafgfoenraeln
對角線
exchhaaunsgte
交換
tdiaglital
差數分控放多大頻器掃
dexplanat
耗盡
control
瞄彩色顯示
ion
解釋
diode
二極体
explode
使爆炸
direct
直接
external
tiemagine
照亮
aMc.tTu.rBe.F:
單平均故障
sihnadrupcnteasn
圖像清晰度
meaacnhine
時間
英语单词表(全)
---------v动词n名词Adj形容词Adv副词Prep介词practisev.练习cityn.城市parent n.父；母(pl.parents父母)canv.aux能够basketball n.篮球piano n.钢琴tennis n.网球tabletennis乒乓球ride v.骑；开（车）horse n.马welcome v.欢迎international adj.国际的factoryn.工厂hotel n.饭店；宾馆university n.大学hospitaln.医院office n.办公室doctor n.医生workern.工人manager n.经理photo n.照片family n.家庭television n.电视right adj.正确的sciencen.科学；科学课lab(=laboratory)n.实验室buildingn.建筑物auntn.姨；伯母;婶母;舅母;姑母grandparentn.（外）祖父；（外）祖母uncle n.叔叔；伯伯；舅舅；姑父；姨父sister n.姐；妹have v.有email n.电子邮件healthyadj.健康的drink n.饮料v.喝Fruit n.水果vegetable n.蔬菜favourite adj.最喜欢的team n.队伍eveningn.晚上idea.想法；主意invite v.邀请on adj.进行；上演magic n.魔术show n.表演dayn.日子；白天place n.地点price n.价格theatren.剧院momentn.时刻swimming n.游泳come v.来today adv.今天plan n.计划playgroundn.操场stayv.停留game n.游戏talkv.谈论time n.时间history n.历史at prep.在（某时间或时刻）start v.开始getup起床have v.吃breakfast n.早饭house n.房子；住宅break n.（课间）休息lunch n.午饭orconj.或者gohome回家dinner n.晚饭；正餐finish v.结束；完成park n.公园housework n.家务劳动different adj.不同的habit n.习惯always adv.总是；一直card n.卡片present n.礼物usually adv.通常often adv.经常never adv.从不---------getv.得到send v.发送ticket n.票pairn.双；对concertn.音乐会boxn.盒子silkn.丝绸shirt n.衬衫magazine n.杂志novel n.小说CDn.(=compactdisk)光盘choosev.选择，挑选lot大量；许多lotsof大量；许多alotof大量；许多clothesn.衣服（总称）music n.音乐singer n.歌手on prep.通过，以⋯⋯方式ontelevision通过电视；在电视上its物主代词它的think v.想，认为thinkof想出tripn.旅行zoon.动物园tiger n.老虎camel n.骆驼elephant n.大象lionn.狮子giraffe n.长颈鹿kangaroo n.袋鼠monkeyn.猴子panda n.熊猫snake n.蛇wolf n.狼polarbear北极熊guide n.导游thousand num.千visitv.参观；访问n.参观；访问everyadj.每一个／只animal n.动物zebra adj.斑马more adj.更多Australia n.澳大利亚Australian adj.澳大利亚的Arctic n.北极Europen.欧洲European adj.欧洲的Asian.亚洲Asian adj.亚洲的here adv.在这里bamboon.竹子Africa n.非洲Africanadj.非洲的American.美洲；美国Americanadj.美洲的；美国的；美国人的Oceanian.大洋洲Oceanian adj.大洋洲的desert n.沙漠forest n.森林jungle n.热带雨林grass n.草grassland n.草原(Indialeafn.叶子(pl.leaves)world n.世界computer n.电脑；主机keyboard n.键盘monitorn.显示器mousen.鼠标；老鼠print v.打印printer n.打印机connectv.连接switch v.用开关把⋯⋯开启（或关掉）Switchon接通；开（电灯、机器等）finally adv.最后firstadv.首先document n.文件usev.使用click v.点击next adv.然后；其次save v.保存；挽救boxn.方框then adv.然后again adv.再一次；又online adj.在线的n.印度---------travel n.旅行download v.下载Internetn.网络grandchildn.（外）孙子；（外）孙女sometimesadv.有时候；不时checkv.检查train n.火车timetable n.时刻表laptop n.笔记本电脑weekend n.周末websiten.网站Londonn.伦敦informationn.信息Kind n.种类subjectn.科目buyv.买callv.打电话drive v.开车enjoy v.享受lie v.躺下shop v.逛商店；购物takev.获得；拿；抓Takephotos拍照tellv.讲；告诉Wait v.等forprep.为，为了waitfor等待；等候postcard n.明信片theGreatWall长城reallyadv.（表语气）真的吗agoodtime美好时光alot非常anywayadv.转换话题结束谈话时说无论如何，反正carn.小汽车puton穿上thing n.事情；东西leave v.离开work n.&v.工作athome在家pubn.酒馆restaurant n.饭馆opera n.歌剧ballet n.芭蕾舞sleep v.&n.睡觉wash v.洗；洗涤dress v.穿衣服start n.&v.开始middayn.正午hotdog热狗coffee n.咖啡seev.探望；看见greetingn.问候；致意atthemoment现在，此时lookat看⋯⋯soon adv.立刻；不久loven.&v.爱；热爱Seeyoulater.再见。
工厂常见英语单词
从事质量工作以来积累的常用英语，希望对有需要的朋友有所帮助！质量专业英语大全零件材料类的专有名词CPU: central processing unit(中央处理器)IC: Integrated circuit(集成电路)Memory IC: Memory Integrated circuit（记忆集成电路）RAM: Random Access Memory（随机存取内存）DRAM: Dynamic Random Access Memory（动态随机存取内存）SRAM: Staic Random Access Memory（静态随机内存）ROM: Read-only Memory（只读存储器）EPROM:Electrical Programmable Read-only Memory（电可抹只读存诸器）EEPROM: Electrical Erasbale Programmable Read-only Memory（电可抹可编程只读存储器）CMOS: Complementary Metal-Oxide-Semiconductor（互补金属氧化物半导体）BIOS: Basic Input Output System（基本输入输出系统）Transistor：晶体管LED:发光二极管Resistor：电阻Variator：可变电阻Capacitor:电容Capacitor array：排容Diode：二极管Transistor：三极体Transformer：变压器（ADP）Oscillator：频率振荡器（0sc）Crystal：石英振荡器XTAL/OSC:振荡产生器（X）Relay：延时器Sensor：感应器Bead core：磁珠Filter:滤波器Flat Cable：排线Inductor：电感Buzzer：蜂鸣器Socket：插座Slot：插槽Fuse：熔断器Current：电流表Solder iron：电烙铁Magnifying glass：放大镜Caliper：游标卡尺Driver：螺丝起子Oven：烤箱TFT:液晶显示器Oscilloscope：示波器Connector：连接器PCB:printed circuit board（印刷电路板）PCBA: printed circuit board assembly（电路板成品）PP:并行接口HDD:硬盘FDD:软盘PSU:power supply unit（电源供应器）SPEC:规格Attach:附件Case: 机箱，盖子Cover：上盖Base：下盖Bazel：面板（panel）Bracket：支架，铁片Lable：贴纸Guide：手册Manual：手册，指南Card：网卡Switch：交换机Hub：集线器Router：路由器Sample：样品Gap：间隙Sponge：海绵Pallet：栈板Foam：保利龙Fiber：光纤Disk：磁盘片PROG:程序Barcode：条形码System：系统System Barcode：系统条形码M/B:mother board：主板CD-ROM:光驱FAN:风扇Cable：线材Audio：音效K/B:Keyboard（键盘）Mouse：鼠标Riser card：转接卡Card reader：读卡器Screw：螺丝Thermal pad：散热垫Heat sink：散热片Rubber：橡胶垫Rubber foot：脚垫Bag：袋子Washer：垫圈Sleeve：袖套Config：机构Label hi-pot：高压标签Firmware label：烧录标签Metal cover：金属盖子Plastic cover：塑料盖子Tape for packing：包装带Bar code：条形码Tray：托盘Collecto：集线夹Holder：固定器,L铁Connecter：连接器IDE:集成电路设备，智能磁盘设备SCSI:小型计算机系统接口Gasket：导电泡棉AGP:加速图形接口PCI:周边组件扩展接口LAN:局域网USB:通用串形总线架构Slim：小型化COM:串型通讯端口LPT:打印口，并行口Power cord：电源线I/O:输入，输出Speaker：扬声器EPE:泡棉Carton：纸箱Button：按键，按钮Foot stand：脚架部门名称的专有名词QSuality system质量系统CS:Coutomer Sevice 客户服务QCuality control质量管理IQC:Incoming quality control 进料检验LQCine Quality Control 生产线质量控制IPQC:In process quality control 制程检验FQC:Final quality control 最终检验OQC:Outgoing quality control 出货检验QAuality assurance 质量保证SQA:Source(supplier) Quality Assurance 供货商质量保证(VQA) CQA：Customer Quality Assurance客户质量保证PQArocess Quality Assurance 制程质量保证QEuality engineer 质量工程CE:component engineering零件工程EE:equipment engineering设备工程ME:manufacturing engineering制造工程TE:testing engineering测试工程PPEroduct Engineer 产品工程IE:Industrial engineer 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部A/D: Accountant /Finance Dept会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchaing Dept)SMT:Surface mount technology 表面粘着技术MFG:Manufacturing 制造MIS:Management information system 资迅管理系统DCC:document control center 文件管制中心厂内作业中的专有名词QTuality target质量目标QPuality policy目标方针QI:Quality improvement质量改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT:主要缺点（MA）MINOR DEFECT:次要缺点（MI）MAX:Maximum最大值MIN:Minimum最小值DIAiameter直径DIMimension尺寸LCLower control limit管制下限UCL:Upper control limit管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO:Engineering change order工程改动要求（客户）ECR:工程变更需求单CPI:Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWGrawing图面Standardization：标准化Consensus：一致Code：代码ZD:Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM:Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力) PMP:制程管理计划（生产管制计划）MPI:制程分析DASefects Analysis System 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment自动测试设备MO: Manafacture Order生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)AS组立P/K:包装TQM:Total quality control全面质量管理MDA:manufacturing defect analysis制程不良分析(ICT) RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM即为% Corrective Action: (CAR改善对策)ACC：允收REJ:拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession / Waive特采ISO:国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action计划，执行，检查，总结WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL:acceptable quality level允收质量水平LQL;Limiting quality level最低质量水平QVL:qualified vendor list合格供货商名册AVL ：认可的供货商清单(Approved Vendor List) QCD: Quality cost delivery（质量，交期，成本）MPM:Manufacturing project management制造项目管理KPI:Key performance indicate重要绩效指标MVT:Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL:ship to line（料到上线）NTF:No trouble found误判CIP:capacity improvement plan（产能改善计划）MRB:material review board（物料审核小组）MRB:Material reject bill退货单JIT:just in time（实时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP:standard operation process（标准作业程序）SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD:surface mounting device（表面粘着原件）FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告BPR：企业流程再造(Business Process Reengineering) ISAR ：首批样品认可(Initial Sample Approval Request)- JIT：实时管理(Just In Time)QCC ：品管圈(Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面质量环境管理)PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供货商质量管理系统QIT: Quality Improvement Team 质量改善小组QIP：Quality Improvement Plan质量改善计划CIP：Continual Improvement Plan持续改善计划Material Quality Feedback Sheet (来料质量回馈单)SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知)QAPS: Quality Assurance Process Sheet (质量工程表)DRP ：运销资源计划(Distribution Resource Planning)DSS：决策支持系统(Decision Support System)EC ：电子商务(Electronic Commerce)EDI ：电子数据交换(Electronic Data Interchange)EIS ：主管决策系统(Excutive Information System)ＥＲＰ：企业资源规划(Enterprise Resource Planning)FMS ：弹性制造系统(Flexible Manufacture System)KM ：知识管理(Knowledge Management)4L ：逐批订购法(Lot-for-Lot)LTC ：最小总成本法(Least Total Cost)LUC ：最小单位成本(Least Unit Cost)MES ：制造执行系统(Manufacturing Execution System) MPS ：主生产排程(Master Production Schedule)MRP ：物料需求规划(Material Requirement Planning) MRPⅡ：制造资源计划(Manufacturing Resource Planning) OEM ：委托代工(Original Equipment Manufacture) ODM ：委托设计与制造(Original Design & Manufacture) OLAP：在线分析处理(On-Line Analytical Processing) OLTP：在线交易处理(On-Line Transaction Processing) OPT ：最佳生产技术(Optimized Production Technology) PDCA：PDCA管理循环(Plan-Do-Check-Action)PDM：产品数据管理系统(Product Data Management)) RCCP：粗略产能规划(Rough Cut Capacity Planning)SCM ：供应链管理(Supply Chain Management)SFC ：现场控制(Shop Floor Control)TOC：限制理论(Theory of Constraints)TQC ：全面质量管理(Total Quality Control)FYI/R:for your information/reference仅供参考ASAP:尽快S/T:Standard time标准时间TPM:total production maintenance：全面生产保养ESD Wrist strap：静电环IT:information technology信息技术，信息科学CEO：Chief Executive Officer执行总裁COO：Chief Operaring Officer首席业务总裁SWOT：Strength,Weakness,Opportunity,Threat 优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通转自: [url=外贸验货员网[/url]。
工厂常见英语单词
从事质量工作以来积累的常用英语，希望对有需要的朋友有所帮助！质量专业英语大全零件材料类的专有名词CPU: central processing unit(中央处理器)IC: Integrated circuit(集成电路)Memory IC: Memory Integrated circuit（记忆集成电路）RAM: Random Access Memory（随机存取内存）DRAM: Dynamic Random Access Memory（动态随机存取内存）SRAM: Staic Random Access Memory（静态随机内存）ROM: Read-only Memory（只读存储器）EPROM:Electrical Programmable Read-only Memory（电可抹只读存诸器）EEPROM: Electrical Erasbale Programmable Read-only Memory（电可抹可编程只读存储器）CMOS: Complementary Metal-Oxide-Semiconductor（互补金属氧化物半导体）BIOS: Basic Input Output System（基本输入输出系统）Transistor：晶体管LED:发光二极管Resistor：电阻Variator：可变电阻Capacitor:电容Capacitor array：排容Diode：二极管Transistor：三极体Transformer：变压器（ADP）Oscillator：频率振荡器（0sc）Crystal：石英振荡器XTAL/OSC:振荡产生器（X）Relay：延时器Sensor：感应器Bead core：磁珠Filter:滤波器Flat Cable：排线Inductor：电感Buzzer：蜂鸣器Socket：插座Slot：插槽Fuse：熔断器Current：电流表Solder iron：电烙铁Magnifying glass：放大镜Caliper：游标卡尺Driver：螺丝起子Oven：烤箱TFT:液晶显示器Oscilloscope：示波器Connector：连接器PCB:printed circuit board（印刷电路板）PCBA: printed circuit board assembly（电路板成品）PP:并行接口HDD:硬盘FDD:软盘PSU:power supply unit（电源供应器）SPEC:规格Attach:附件Case: 机箱，盖子Cover：上盖Base：下盖Bazel：面板（panel）Bracket：支架，铁片Lable：贴纸Guide：手册Manual：手册，指南Card：网卡Switch：交换机Hub：集线器Router：路由器Sample：样品Gap：间隙Sponge：海绵Pallet：栈板Foam：保利龙Fiber：光纤Disk：磁盘片PROG:程序Barcode：条形码System：系统System Barcode：系统条形码M/B:mother board：主板CD-ROM:光驱FAN:风扇Cable：线材Audio：音效K/B:Keyboard（键盘）Mouse：鼠标Riser card：转接卡Card reader：读卡器Screw：螺丝Thermal pad：散热垫Heat sink：散热片Rubber：橡胶垫Rubber foot：脚垫Bag：袋子Washer：垫圈Sleeve：袖套Config：机构Label hi-pot：高压标签Firmware label：烧录标签Metal cover：金属盖子Plastic cover：塑料盖子Tape for packing：包装带Bar code：条形码Tray：托盘Collecto：集线夹Holder：固定器,L铁Connecter：连接器IDE:集成电路设备，智能磁盘设备SCSI:小型计算机系统接口Gasket：导电泡棉AGP:加速图形接口PCI:周边组件扩展接口LAN:局域网USB:通用串形总线架构Slim：小型化COM:串型通讯端口LPT:打印口，并行口Power cord：电源线I/O:输入，输出Speaker：扬声器EPE:泡棉Carton：纸箱Button：按键，按钮Foot stand：脚架部门名称的专有名词QSuality system质量系统CS:Coutomer Sevice 客户服务QCuality control质量管理IQC:Incoming quality control 进料检验LQCine Quality Control 生产线质量控制IPQC:In process quality control 制程检验FQC:Final quality control 最终检验OQC:Outgoing quality control 出货检验QAuality assurance 质量保证SQA:Source(supplier) Quality Assurance 供货商质量保证(VQA) CQA：Customer Quality Assurance客户质量保证PQArocess Quality Assurance 制程质量保证QEuality engineer 质量工程CE:component engineering零件工程EE:equipment engineering设备工程ME:manufacturing engineering制造工程TE:testing engineering测试工程PPEroduct Engineer 产品工程IE:Industrial engineer 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部A/D: Accountant /Finance Dept会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchaing Dept)SMT:Surface mount technology 表面粘着技术MFG:Manufacturing 制造MIS:Management information system 资迅管理系统DCC:document control center 文件管制中心厂内作业中的专有名词QTuality target质量目标QPuality policy目标方针QI:Quality improvement质量改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT:主要缺点（MA）MINOR DEFECT:次要缺点（MI）MAX:Maximum最大值MIN:Minimum最小值DIAiameter直径DIMimension尺寸LCLower control limit管制下限UCL:Upper control limit管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO:Engineering change order工程改动要求（客户）ECR:工程变更需求单CPI:Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWGrawing图面Standardization：标准化Consensus：一致Code：代码ZD:Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM:Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力) PMP:制程管理计划（生产管制计划）MPI:制程分析DASefects Analysis System 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment自动测试设备MO: Manafacture Order生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)AS组立P/K:包装TQM:Total quality control全面质量管理MDA:manufacturing defect analysis制程不良分析(ICT) RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM即为0.1% Corrective Action: (CAR改善对策)ACC：允收REJ:拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession / Waive特采ISO:国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action计划，执行，检查，总结WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL:acceptable quality level允收质量水平LQL;Limiting quality level最低质量水平QVL:qualified vendor list合格供货商名册AVL ：认可的供货商清单(Approved Vendor List) QCD: Quality cost delivery（质量，交期，成本）MPM:Manufacturing project management制造项目管理KPI:Key performance indicate重要绩效指标MVT:Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL:ship to line（料到上线）NTF:No trouble found误判CIP:capacity improvement plan（产能改善计划）MRB:material review board（物料审核小组）MRB:Material reject bill退货单JIT:just in time（实时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP:standard operation process（标准作业程序）SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD:surface mounting device（表面粘着原件）FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告BPR：企业流程再造 (Business Process Reengineering) ISAR ：首批样品认可(Initial Sample Approval Request)- JIT：实时管理 (Just In Time)QCC ：品管圈 (Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面质量环境管理)PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供货商质量管理系统QIT: Quality Improvement Team 质量改善小组QIP：Quality Improvement Plan质量改善计划CIP：Continual Improvement Plan持续改善计划M.Q.F.S: Material Quality Feedback Sheet (来料质量回馈单) SCAR: Supplier Corrective Action Report (供货商改善对策报告) 8D Sheet: 8 Disciplines sheet ( 8D单)PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知) QAPS: Quality Assurance Process Sheet (质量工程表)DRP ：运销资源计划 (Distribution Resource Planning)DSS：决策支持系统 (Decision Support System)EC ：电子商务 (Electronic Commerce)EDI ：电子数据交换 (Electronic Data Interchange)EIS ：主管决策系统 (Excutive Information System)ＥＲＰ：企业资源规划 (Enterprise Resource Planning)FMS ：弹性制造系统 (Flexible Manufacture System)KM ：知识管理 (Knowledge Management)4L ：逐批订购法 (Lot-for-Lot)LTC ：最小总成本法 (Least Total Cost)LUC ：最小单位成本 (Least Unit Cost)MES ：制造执行系统 (Manufacturing Execution System) MPS ：主生产排程 (Master Production Schedule)MRP ：物料需求规划 (Material Requirement Planning) MRPⅡ：制造资源计划 (Manufacturing Resource Planning) OEM ：委托代工 (Original Equipment Manufacture)ODM ：委托设计与制造 (Original Design & Manufacture) OLAP：在线分析处理 (On-Line Analytical Processing) OLTP：在线交易处理 (On-Line Transaction Processing) OPT ：最佳生产技术 (Optimized Production Technology) PDCA：PDCA管理循环 (Plan-Do-Check-Action)PDM：产品数据管理系统 (Product Data Management)) RCCP：粗略产能规划 (Rough Cut Capacity Planning) SCM ：供应链管理 (Supply Chain Management)SFC ：现场控制 (Shop Floor Control)TOC：限制理论 (Theory of Constraints)TQC ：全面质量管理 (Total Quality Control)FYI/R:for your information/reference仅供参考ASAP:尽快S/T:Standard time标准时间TPM:total production maintenance：全面生产保养ESD Wrist strap：静电环IT:information technology信息技术，信息科学CEO：Chief Executive Officer执行总裁COO：Chief Operaring Officer首席业务总裁SWOT：Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通转自: [url=/bbs/index.php?fromuid=0]外贸验货员网[/url] /bbs/index.php?fromuid=0欢迎您的下载，资料仅供参考！致力为企业和个人提供合同协议，策划案计划书，学习资料等等打造全网一站式需求。
工业英语单词
工业英语单词：提升你的行业交流能力一、基础词汇篇1. Factory（工厂）：工业生产的基本单位，各种产品在这里诞生。
2. Machine（机器）：代替人工，提高生产效率的重要设备。
3. Equipment（设备）：指用于生产、加工、检测等各个环节的器械。
4. Production（生产）：指从原材料到成品的整个制造过程。
5. Quality（质量）：衡量产品好坏的重要标准，关系到企业生存与发展。
6. Safety（安全）：保障员工在生产过程中的人身安全，是企业责任所在。
7. Efficiency（效率）：衡量生产过程中资源利用率的指标，越高越好。
8. Innovation（创新）：推动工业进步的灵魂，是企业持续发展的动力。
9. Automation（自动化）：利用机器设备代替人工操作，提高生产效率。
10. Standardization（标准化）：统一产品质量、规格、性能等，便于生产与管理。
二、工艺流程篇11. Manufacturing（制造）：将原材料转化为成品的过程，涉及多个工序和技术。
12. Assembly Line（流水线）：一种高效的生产方式，通过分工合作提高生产速度。
13. Process（工艺）：指生产过程中的一系列操作步骤和方法。
14. Welding（焊接）：将金属部件通过高温熔化连接在一起的技术。
15. Casting（铸造）：将金属熔化后倒入模具，冷却成型的一种生产方法。
16. Machining（机械加工）：利用切削、磨削等方法，使工件达到预定尺寸和形状。
17. Soldering（焊接）：通过熔化低熔点金属，将金属部件连接在一起。
18. Polishing（抛光）：去除工件表面的粗糙度，使其光滑美观。
19. Inspection（检验）：在生产过程中，对产品进行质量检查，确保合格。
20. Maintenance（维护）：定期对设备进行检查、保养，确保其正常运行。
三、管理术语篇21. Management（管理）：对企业生产、经营等活动进行计划、组织、指挥、协调和控制。
工业常用英语单词
工业常用英语单词工业常用英语单词集散控制系统——DistributedControlSystem(DCS)现场总线控制系统——FieldbusControlSystem(FCS)监控及数据采集系统——SupervisoryControlAndDataAcqusition(SCADA)可编程序控制器——ProgrammableLogicController(PLC)可编程计算机控制器——ProgrammableComputerController(PCC)工厂自动化——FactoryAutomation(FA)过程自动化——ProcessAutomation(PA)管理信息系统——ManagementInformationSystem(MIS)楼宇自动化系统——BuildingAutomationSystem人机界面——HumanMachineInterface(HMI)工控机——IndustrialPersonalComputer(IPC)单片机——SingleChipMicroprocessor计算机数控(CNC)远程测控终端——RemoteTerminalUnit(RTU)上位机——SupervisoryComputer图形用户界面(GUI)人工智能——ArtificialIntelligent(AI)智能终端——IntelligentTerminal模糊控制——FuzzyControl组态——Configuration仿真——Simulation冗余——Redundant客户/服务器——Client/Server网络——Network设备网——DeviceNET基金会现场总线——foundationfieldbus(FF)现场总线——Fieldbus以太网——Ethernet变频器——Inverter脉宽调制——PulseWidthModulation(PWM)伺服驱动器——ServoDriver软起动器——SoftStarter步进——Step-by-Step控制阀——ControlValver流量计——Flowmeter仪表——Instrument记录仪——Recorder传感器——Sensor智能传感器——SmartSensor智能变送器——SmartTransducer虚拟仪器——VirtualInstrument主站/从站——MasterStation/Slavestation操作员站/工程师站/管理员站——OperatorStation/EngineerStation/ManagerStation。
介绍工厂的英语单词
介绍工厂的英语单词
介绍工厂的英语单词有很多，以下是一些常见的例子：
1. Factory - 通常指的是生产制造的场所，也可以表示某个具体的制造工厂。
2. Mill - 通常用来指代制造工厂或加工厂，尤其是指那些生产钢铁、纸、塑料等产品的工厂。
3. Plant - 通常用来表示工厂或制造场所，也可以用来描述某个具体的生产设备或机器。
4. Workshop - 通常指的是车间或工作坊，也可以用来描述某个具体的制造设备或工具。
5. Foundry - 通常用来指代铸造厂或铸铁厂，也可以用来描述某个具体的铸造设备或工艺。
6. Factory worker - 指的是工厂工人，通常指的是在工厂里从事生产制造工作的人员。
7. Assembly line worker - 指的是生产线工人，通常指的是在生产线上的工人，负责组装或装配产品。
8. Maintenance worker - 指的是维修工人，通常指的是负责维护和修理工厂设备或机器的人员。
9. Quality inspector - 指的是质量检查员，通常指的是负责检查产品质量的人员。
10. Engineer - 指的是工程师，通常指的是负责设计、开发和改进工厂设备或机器的人员。
工厂常用英语单词
1-1 Substitution1-1代用料balance 結余Alternate current交流電bar code label 條碼標籤AC inletAC插座(電源插座)base 基極 基礎acceptable可接受的basic 基本的action行動 行為battery 電池active有效的 現行的bead core 磁線圈active area有效面積biased 偏置active model有效機種block NO 半成品號additional附加的blooming 涂層 開花address label地址標籤board 廠牌 板子adhesive膠 有粘性的BOM:bill of material 物料清單adhesive three bond綠膠bonded 粘合的adhesive silicone矽膠board corrugated paper 天地紙板(棧板上面及Monitor上:)adjustment判斷 調整bottom 底部adjust調整bracket 托架 括弧AI fixtureAI電氣設備bridge rectifier 橋式整流器AI: auto insertion自動插件部brightness 亮度aid援助brightness uniformity 亮度一致性air condition空運條件bulk rectifiers 矯正器air rubble bag氣 泡墊bulky 大宗的 笨大的altitude高度bumps ripples 波紋ALU(capacitor)鋁質(電解電容)burning room 燒機房 加溫室amber琥珀色by block NO 按機種半品料號階排列ampere安培by model NO 按機種排列amplifier放大器analog模擬cable 線analysis分析cable ties 束線袋application應用cablet bracket 固定片apply應用 申請CAI:computer AID issuring 電腦自動模擬發料approval審核 承認cancel 取消approve同意 贊成CAP:Capacity 電容arrange整理CAP ALU ELECTROLYTIC-400V 鋁質 電解電容 400以上assign指定,分配CAP ALU ELECTROLYTIC-OTHE 電解電容attachment附件CAP FILM SPECIAL 薄膜電容audio音頻CAP MEF 金屬化聚乙脂膜電容器audio board音量板CAP MEM 小型化塑膠電容(MEF)audit檢核CAP MPP 金屬化聚丙烯膜電容automatic degaussing自動消磁CAP PEI 聚丙乙烯膜電容(無感式)available 準備好的 通用的CAP PEM 聚丙乙烯膜電容(有感式)CAP PPM 聚丙烯電容器collector 集電電路CAP PPN 聚丙烯薄膜電容color/colour 顏色CAP PPS 串連式聚丙烯膜電容器color sticker 彩色貼紙CAP PS 聚丙乙烯膜電容器度射column 列CAP TAN 鉭電容commodity 屬性 種類CAP VARIABLE 可變電容common base 共基電路CAP Y Y電容common choke 環形濾波線圈CAR:corrective and action report 校正與預防措施 報告common choke 普通扼流圈capability 性能 能力company 公司capacitor 電容 容量compare 比較 對照capacity 能量 電容compatibility 兼容性capatine/with 可連接/插上complain 抱怨capacity 電容component 零件calendar 日程表computer 計算機carton 紙箱condition 條件carton box 紙箱confirm 確定cause 原因connector 連接器CC resistor 碳合成電阻consumption 消耗CD(capacitor)陶瓷電容continue 繼續CEM resistor 水泥電阻control chart 控制圖center 中心contract 合同carbon film resistor 碳膜電阻contrast 對比度CR resistor 碳膜電阻(色碼電阻)control BD 控制板change your password 改變密碼core magnetic 磁鐵 磁芯characteristics 特性corrective 改善的charge 使承擔 使負擔cost 成本chart 流程圖coustomer 顧客 客戶chassis 機座critical 極限 限制check 檢查CRT 映像管check point 檢查點CRT board CRT電路板choke 扼流圈CRT GND WIRE CRT接地線chromaticity 色度CRT screw CRT螺絲circuit 電路CRT socket CRT插座circuit board 電路板CRT test CRT測試CKD-ID 位置CRT:cathode ray tube 陰極射線管cleaner naphtha 清潔劑current 電流clip 夾子cushion 墊片code 代碼CUT-IN code 切入代碼coil 線圈coil rotation 傾斜線圈daily 每日的coil choke 扼流線圈data display area dimension and posi 數據顯示區域coil degaussing 消磁線圈date 日期coil linear 枕型調整線圈date code label 日期標籤coil peaking 蜂化線圈direct current 直流電conductivity 電導率DC input impedance 直流輸入阻抗本冊英語單詞是工廠常用之基本詞匯.DAB C 第 1 頁 共 13 頁DDC:display data channel 顯示器數據通道electrostatic 靜電defect 不良electrostatic discharge 放靜電deffused ambient 散射環境EMI:(Electronic&Magnetic Interfere 電磁干擾濾波器define 解釋emittor 放射極deflection 偏轉EN:engineer notice 工程通知degree 角度enclosure 包圍delete 刪除engineering specification 工程規范delivery 交貨enter 確認 進入delivery order 送貨單environmental 環境的decide 解決 決定 裁決equivalent 等效description 規格 說明error 錯誤destination 目的地ESD:electrical static discharge 靜電detail 明細estimate disable 預定的deviate 偏差excess 過剩diagonal 對角線exchange 交換differential amplifier 差分放大器exhausted 耗盡digital control multiscan color monit 數控多頻掃瞄彩色顯示explanation 解釋diode 二極体explode 使爆炸direct 直接external 外面的direct current 直流電disable 使無能factory 工廠discharge 泄放fail 失敗discriminate 區分fan 扇子disk driver 硬盤驅動器FBT:fly back transformer 高壓包display 顯示 展示feature 特性display power management signal 顯示器電源管理信號feedback 回饋 回接(geometry)distortion (几何)失真fotter plate 底座壓制片distribution 令發 分配film stretch wrap 包裝機台伸縮膠膜dot pitch 點距filter 濾波器document center 文件中心final approved 核準door 門finance 財務dot 點first floor 一樓double 雙倍的function led lens 顯是燈座double thread screw 雙牙螺絲(鎖塑膠)flange hex nut 防滑螺絲DQA:design qaulity assurance 設計品質驗證課flat square screen 平面直角屏幕drop test 落下測試flex cable 多蕊電量dynamic 動態flow 流量dynamic performance defeat 動態測試不良flux 電通量dynamic HV 動態高壓flyback 返馳foot pad 角墊ear phone b/d 耳機機板foot-lamberts FL 亮度單位ECN:engineering change notice 工程變更通知form 表單ECR:engineering change request 工程變更申請format 格式化edit 編輯frame 構架electronic 電子F/C front cover 前殼fuse resistor 保險絲電阻information 信息function 功能 運行input 投入function key 功能鍵input signal 輸入信號function test 功能測試inquiry 查詢fabricate 制作 裝配inrush current 開機電流fuse 保險絲insert 插入fuse clip 保險絲座inspection 檢驗future 將來inspector 檢驗者instruction card 指示卡(牌)gap 縫隙insufficient solder 焊錫不足Gauss 高斯(磁場單位)insulation wire 絕緣導線generate 產生interiaced 交織geometry ate fixture&program internal audit 內部審核geometric distortion 几何失真invar 一種低澎脹合金goal 目標inventory 存貨good 良品 好的invoice 發票good finished 成品IPQC:in process quality control 制程品質管制graphic 圖形IQC:incoming quality control 進料品質管制gross 總的ISO:international standard organizat 國際標準化組織gross request 總需求issue quantity 發料量guarantee 保證item 項目guide rail PC板保護條item master 料號主檔heat sink 散熱片jitter 抖動height 高jumper wire 跳線HI-POT OK label 高壓OK標籤junction 連接 結HI-pot test 高壓測試high priority(use substitution item fi 第一優先(代用料)L/P:light&play L/P測試 動態測試highlight 突出label 標簽hold 拿放 抑制 控制led 指示燈horizontal 水平的life test 壽命測試hot melt adhesives 熱容膠line date 上線日harness 排線linear filter 線性濾波變壓器humidity 濕度linearity 線性link bar 連接焊linear integrated circuit 線性集成電路local 本地的IC power 功率集成電路login 登入IC socket IC插座logout 登出IC(digital) AC 數位集成電路low radiation 低幅射IC(integrated circuit)集成電路luminance 揮發 發揮idle 呆料illuminate 照亮MO:manufacture order 制令 工單imagine sharpness 圖像清晰度M.T.B.F:mean time between failure 平均故障時間inductance 電感machine screw 機械螺絲inductor 電感器main 主要的第 3 頁 共 13 頁LME F第 2 頁 共 13 頁G H I Jmain board 主機板mainland 大陸name plate 裝飾片maintain 維護negative 否定的 反向的負極性 major 主要的net shortage 淨需求maker 制造者network 綱路management 管理 安排new model check list 新機種一線檢查表manual 說明書NG=NOT GOOD 非良品manual 用手的 人工的 說明書notice 通知manual PR 人工 PR NUT 螺帽manufacturing 制造master 主人 掌握obligation 義務 責任material 物料ohm 歐姆(電阻單位)material approve 物料承認書order 訂單material return 退料on hand 庫存maylar(capacitor)聚乙酯樹酯電容option 選擇MC:material control 物料控制OQC:out going quality control 出貸品質管制MCR:mechanical changed request 機構變更申請order balance 訂單余數MDR:material defeat report 物料不良報告original 最初ME:manufacture engineering 制造工程original material 原始材料 本料measurement 測量outline 輪廓MEB(capacitor)金屬化多元指電容 mechanical 機構的P.O:purchase order 採搆訂單melt 熔化 熔解P.R: purchase request 採搆需求menu 菜單metal washer 金屬墊圈packing 包裝meter 測量儀表packing label 包裝祇箱標簽method 方法packing list 包裝明細MFG:manufacturing 制造pad 軟墊圈MI:manual insertion 手工插件pallet 棧板minor 次要的 輕微的parameter 參數MIS:manage information system 資訊部part NO P/N 料號model 機種 型號password 密碼 口令model label(ID label)機種標籤payment term 付款期限model name 機種名稱PC:production control 生產控制MOF resistor 金屬膜電阻PCB board film PCB圖片moire 波紋PCB ckt PCB上位置monitor 顯示器PCB:print Circuit Board 印制線路板monthly 月度的PE BAG PE 袋MOS-FET 金氧場效電晶體PE:production engineering 產品工程MPP(capacitor)金屬化多元指電容peaking 峰值MRP FCST LIST MRP需求預測表relay 繼電器MRP:material request plan 物料需求計劃percentage 百分率MTL:material control 物料部 資材部perform 履行magnetic field 磁場perform your own function 發揮自己的功能multiple 复合的 多層次的performance 作業 操作 表演pilot lamp 指示燈recall复位 收回pin assignment 管腳排布receiving接收pitch 間距receiving store收料倉pixel 象素 象元receiving report收料報表plastic resin 合成松香rectangle矩形 長方形plug 轉接頭rectifier整流器problem 問題,難題reduce減少plug and play 即插即用regulation管理 調整 規則polyfoam 保麗龍reject reason判退原因posistor 熱敏電阻reject判退posistor resistor 熱敏電阻(正溫度系數)relation關係positive 正極性的relay繼電器power 功率 電力 電源reply答复power cord 電源線request quatity需求量power knob 開關按鍵requirement要求power MO-SFET 功率晶體resistor電阻power switch 電源開關resolution解析度prevent 防止 預防result結果prepared 放置模式 準備resultant合成的 結果preset mode 預調(畫面)retrace追蹤 探查priority 優先revision修訂版procedure 程序過程rework重工processing 處理ripple波紋 漣綺product tree diagram 產品樹狀圖rivet卯釘production 生產rotary VR:Variable Resistor可旋轉的可變電阻project engineer 項目 工程師row行promote 促使rubber pad橡膠墊片proposed 建議,推薦power mos driver電源MOS驅動器protection 保護public inquiry 公共查詢sponge海棉public report 公共報表spring彈簧pulse 脈沖stability穩定性PUR purchase 採購 購買standard標準的PVC insulator PVC 絕緣片static靜態的status狀況rag 抹布stock庫存品random 隨機的store儲藏range 範圍SUB assembly半品代號raster 光柵 光域substitution代替 替代 代用料rate 比率suggestion建議 意見ratings 預定值summary慨括R/C:rear cover 後殼supply供應reason 原因support支撐reason code 原因代碼surge 振蕩R P第 5 頁 共 13 頁第 4 頁 共 13 頁NOSP.S.I:production shippment inventionretail 零售suspend/stand by 中止/暫停 等待等命swivel旋轉speaker Assembly 喇叭組裝swivel ball底坐圓盤spec list 規格清單swivel base底盤spec 規格symopom現象special 特殊的synchronization同步specification 規格system系統status 狀況S.O :sale order業務訂單stock 庫存品S.O:shop order工單store 儲藏S.W:diode整流二極體SUB assembly 半品組裝S/N:series no流水號substituuon 代用的 代用的safety code安規代碼suggestion 建議 意見safety stock安全庫存summary 慨括sample樣品supply 供應schedule計劃support 支撐scope範圍screw 螺絲scrap報廢socket 插座screw螺絲swivel 旋轉screw+washer螺絲加墊片swivel ball 球座second source代用料swivel base 底盤sequence順序symoboy 現象selection選擇synchronization 同步separtesync分開信號system 系統series NO.系列號set up設立TANT(capacitor)鉭質電解電容shift轉移 變化tape 膠帶shielding cover隔離罩tapping screw 缺口自攻螺絲ship date出貨日期target 目的shipment出貨TE:test engineering 測試工程shipping schedule出貨計劃temperature 溫度shipping store出貨倉term 期限 時限shortage缺料test pin 測試針 插頭 管腳shortage quantity缺料量test template 測試樣品signal to noise倍噪sponge 海棉simulation模擬 模仿spark gap 放電管size by inch寬度thyristor ser 可控整流器slide SW/PUR SW/TACT滑動/電源開關tilt 傾斜switch開關timing update 及時修改solder焊接 焊接劑tolerance 容限 誤差solder wire錫絲top/bottom 頂/底source資源TOTAL 總計spacer support間隔柱 扣子trade 貿易 商業spare parts備用品transter 調動spark gap放電隙transistor 三極管spark tube放電管transistor(TR)電晶體speaker 喇叭voltage/frequency 電壓/頻率VR knob 旋 紐video mode descriptions 可視方式描述VR 可變電阻video b/d(CRT BD)CRT板video cable 信號線wafer 晶片 干膠片wafer 封箱紙company policy&procedure 公司制度與規章warehouse 倉庫coding system 物料編號系統warning label 警告標簽item master 項目表warranty card 保證卡BOM bill of material 各機種之物料冊width 寬度component specification 材料規格書WIP work in process 在製品SRA substitution request authorizati 使用代料授權書wire 線材ECN engineering change notice 工程變更通知書wire saddle 隔離束線座notification 聯絡單engineering specificaton 工程規格書X-RAY label 輻射標簽alignment specification 調整規格書xformer 變壓器inspection specificaton 檢驗規格書xformer hordrive 水平驅動變壓器assembly process 制程指導書xformer pincusion 線性調整變壓assembly drawing 裝配圖xformer power 電源變壓器control run 小量試作管制MAP manufacturing assurance plan 制造品質保證計劃zenar diode 穩壓二極体check list criteria 檢驗表及標準uncommon list 機種差異表u/p unit price 單價CAR corrective action report 矯正改善報告uncommon list 專用材料表 差異表SOP standard operation process 標準操作程序under request 超耗GR&R gauge reliability&repeatabili 可靠性標準校驗unformity 均衡性OSD INT MENU OSD功能說明upc label 客戶代碼標簽contrast 對比urgent 緊急的brightnes 亮度user control and indicate 用戶控製的及提示H.SIZE(H.=horizontal)水平尺寸user 使用者 用戶H.Position 水平相位V.SIZE(V.=vertical)垂直尺寸V.D.S vender delivery schedule 廠商交貸計劃V.position 垂直中心VAL 單位V.pincushion 垂直針墊valid 有效的trapezoid 不規則四邊形variation 變化PIN/BALANCE 內凹/外凹varister 變阻器parallelogram 平行四邊形varistor resistor(vr)可變電阻rotation 旋轉傾斜video display interface 視頻顯示器接口color 顏色vendor 廠商 language 語言vertical 垂直的DISP.FREQ.(Display frequency)頻率顯示VESA:vedio electronic standard asso 示頻電子標準協會degauss 消磁VGA video graphic adapter 視頻圖形適配器recall 復歸VIA 通過H.moire H.一種有波紋的絲綢video cabel 信號線V.focus 垂直聚焦第 6 頁 共 13 頁V 主要資料與文件W 第 7 頁 共 13 頁T Z U Xvibration震動vibration test 震動測試PRE-alignment 1預調 1magnet 磁鐵PRE-alignment 2預調 2selicone 矽膠PRE-alignment 3預調 3glue 白膠rag 抹布hand gloves 手套burn in retest 加溫複檢cleaning solvent 清潔劑white balance 白平衡調整packing tape 膠帶center raster 底色調整lift pallet 棧板purity 色純hand lift 油壓車convergence=CG 收歛cart 手推車tilt 傾斜調整畫面不良代碼ATE 几何自動調整poor F/V adj 頻率轉換不良inspection 檢驗poor vertical 垂直不良INSP.2(convergence)收歛檢驗vert. over scan 垂直過大INSP.3(final)最終檢驗vert under scan 垂直過小safety inspection 安規檢驗poor vert linearity 垂直相性不良R/C screw 鎖後殼poor vert center 垂直中心不良R/C inspection/preparation 後殼檢驗與準備poor vert sync 垂直同步不良HI-POT test 高壓漏電測試vert damping 垂直反折cable tie 綁訊號線spot when power ON/OFF 關機打點monitor carrier 顯示器搬運vert white bar 一縱線packing station 包裝站別hor over scan 水平過大cleaning and wiping 去污與擦淨hor under scan 水平過小carton label 紙箱標簽retrace line 歸線model label 機種標簽hor no sync 水平不同步packing plastic 包裝塑膠袋子hor damping 水平反折putting manual 放入說明書手冊poor screen 畫面不良packing-carton box 包裝-紙箱poor center 水平中心不良finished goods filling 完成的貨物裝填dog ear 線性扭曲.拉角repair 修理poor hor linearity 左右大小格生產線常用名辭認識poor hor phase 水平相位不良board pallet 板子trap distortion 梯型不良stopper 踏板pincushipon distortion 針墊形不良electric screw driver 電槍smear 拖色 拖影glue gun 膠槍red bias 紅色偏壓cutter nip 斜口鉗green bias 綠色偏壓long nose nip 長鼻鉗blue bias 藍色偏壓soldering iron 烙鐵red drive 紅色驅動solder lead 錫絲green drive 綠色驅動 45VPPdesoldering gun 吸錫器blue drive 藍色驅動multitester 三用電表poor focus 聚焦不良adjuster 調棒no picture 無影像hamlet chamber 磁場brightness too dark 畫面過暗counter 計數器 相反raster show 底色不良color analyzer 色溫儀poor brightness F4F4不良poor contrast control 對比控制不良function key board Function key BDpoor brightness control 亮度控制不良audio board Audio BDpoor G2G2控制不良speaker 喇叭poor bottom 按鍵無作用MIC phone 麥克風led off LED击陷不亮styrofoam 保麗龍tilt 縫隙.傾斜PE bag 塑膠袋F/C logo poor print 面框/印刷不良carton 紙箱poor video cable 信號線不良resistor 電阻insulator panel 安規片作業不良capacitor 電容poor covergence 收歛不良coil 電感(線圈)poor purity 色純度不良transistor 電晶體poor CRT CRT不良field effect transistor 場效電晶體no power 無電源integrated circuit 積體電路poor power saving 省電不良diode 二極體no raster 無光域variable resistor 可變電阻flash LED LED閃爍high voltage transformer 高壓變壓器smoking 冒煙.跳火yoke 便向軛poor degauss 消磁作用不良antenna 天線poor power SW 開關作用不良speaker 揚聲器poor start UP 起動不良poor voltage 電壓不良poor Hi-pot test 高壓測試不良not completely assembly 組裝未入interference 干擾reverse assembly 組裝反向moire 紋路assembly of lost part 組裝缺件noise 異聲.雜音poor wire dressing 佈線不良waggle 抖動.幌動.閃爍poor operating 作業不良ENGLISH DESCRIPTION poor assembly 組裝不良damage 損壞問題ground wire 接地線damage board PCB損壞degaussing coil 消磁線圈damage parts 零件損壞tilt coil=Rotation coil 傾斜線圈damage wire 線材損壞other wire 其他線材copper pad rising 銅箔翹皮anode cap 高壓帽cpper pad on board is broken 銅箔斷裂signal cable 信號線INSERTING PROBLEM插件問題label 標籤parts lost in AI AI缺件screw 螺絲wrong parts in AI AI錯件function key 功能鍵parts reversed in AI AI極性反front cover=F/C 前框parts is not insert into AI AI未插入rear cover=R/C 後框redundant parts in AI AI多件UL shield cover UL 安規片parts lost in MI MI缺件EMI shield cover EMI電磁干擾防護片wrong parts in MI MI錯件MPR II shield cover 幅射防護片parts reversed in MI MI極性反第 9 頁 共 13 頁(組裝/包裝問題)第 8 頁 共 13 頁CHINESE敘述(組裝段站別)FINAL ASSEMBLY STATION ALIGNMENT STATION (調整段站別)ASSEMBLY/PACKING PROBLEMmain boardMain BD(主機板)parts is not insert into MI MI未插入CRT boardCRT BD redundant parts in MI MI多件LED board LED BD components short each other 短路至其他部份others 其他moire水波紋ALIGNMENT PROBLEM 調整問題jitter/waggle畫面跳動/搖擺voltage adjust 電壓調整pix flash畫面閃爍function align 功能調整poor focus聚焦不良mechnical adjust 機構調整XRP CKT mal-functionXRP動作不良others 其他調整 F.W.T敲打不良OTHER PROBLEM 其他問題mute NG切換畫面不良beyond economic repair 非經濟維修other picture problem其他畫面不良difficult repair 修護困難red bias紅色偏壓engineer problem 工程問題green bias綠色偏壓no fail found 沒有不良發現blue bias藍色篇壓rework 重工red drive紅色驅動parts defect 零件不良green drive綠色驅動component defect 零件不良blue drive藍色驅動color change書色變色smear/tailing模糊/拖影cold solder/dry joint 冷焊/空焊different color at H&V line水平&垂直不同色older broken 錫點破裂impurity/doming色純度不良solder ball/solder short 錫球/錫短路blemish/phospher lost污點solder less 吃錫不良bri.too dark書面過暗others 其他raster show底色出現Hor. over/under scan 水平寬度過大/過小block L/O out of spec小方塊亮度超出規範poor hor.linearity 水平線性不良ABL L/O out of spec全白亮度超出規格hor.no sync 水平不同步poor contrast control對比控製不良hor fold over 水平反折poor bri. Control亮度控製不良poor hor center 水平中心不良poor G2 controlG2控製不良poor hor phase 水平相位不良other color problem其他顏色不良spot when power on/off 開/關機打點L/R output unbalance左右聲音輸出不平衡vert.collapse 一縱線L/R no put左右聲音不輸出vert over/under scan 垂直高度過大/過小Buzz共振聲poor vert.linearity 垂直線性不良noise雜音vert.no sync 垂直不同步sound putput intermittent聲音輸出斷續vert.fold over 垂直反折Ear jack test failure耳機測試不良poor vert.center 垂直中心不良Microphone test failure麥克風測試不良vert.white bar 白Bar Other audio problem其他聲音不良retrace line 歸線NO power無電源hor.collapse 一橫線poor power saving省電功能不良geometry distortion 几何失真LED flash/power can't start-upLED閃爍&無法開機dog ear/top hook 扭曲/拉角smoke冒煙/跳火tilt 傾斜poor degaussing消磁不良no picture 無影像unit can't start-up起動不良pincushion distirtion 針墊不良hi-pot test failure高壓測試不良poor CG 收歛不良GND continue failure導通不良poor screen 畫面不良poor voltage電壓不良interference 干擾poor freg 除頻不良poor dymanic focus 動態聚集不良lack of manpowerpoor F/V adj 頻率轉換不良11.升降機故障High voltage leakage 高壓漏電lifter defectiveother power problem 其他電源不良12.ECN切入,REWORKGap 空隙engineering change notice reworkLoosen 松動13.設計問題,REWORKnot smooth 未平貼design problem, reworkpoor packing 包裝不良14.材料需全檢scratch/broken 損傷/破裂materials hold need sortingchange shape 變形body 毛邊operation 操作poor printing 印刷不良approve 贊成dirty 髒group 群.組(團体)other cosmetic problem 其他外觀不良leader 領班ICT TEST FAILURE ICT測試不良repair 修理micro ctrl latch-up 微電腦控制鎖住warehouse 倉庫micro ctrl data loss 微電腦控制資料遺漏trouble shooter 技術員DDC data error 寫入資料錯誤transfer 調動DDC data can't write-in 資料無法寫入manpower 人力function key can't work 功能鍵不動作DAY/NIGHT SHIFT 日/夜班(線)poor OSD display OSD顯示不良highlight 用強光照射(指提出重大事件)poor ATE ATE無法調net 淨效率Poor USB USB不良gross 毛效率goal 終點 目標1.前殼不足total 總計的line stop/down time(front case shortage)workers 勞動者2.後殼不足urgent 緊急line stop/downtime(rear cover shortage)vertical 垂直3.材料不足horizontal 水平materials/parts shortage procedure 程序4.機構問題control run 小量試作mechanical design defective chassis 基板5.電氣問題inspection 檢驗technical design defective dynamic focus 動態聚焦6.加溫室故障tighten 提高規格burn-in room defective arching 跳火7.生產設備故障guide rail chassis 基板導軌production machine defective carton 紙箱;隔板類程序錯誤drop test 落下實驗program error support 支援(或支架)8.ATE故障combine 合併第 11 頁 共 13 頁停線原因中英對照第 10 頁 共 13 頁焊錫問題常用單詞SOLDERING PROBLEMATE defectiveseparate 分開9.包裝設備故障solution 對策packing machine defectiveaffirm 10.人員不足確定或確認(常用於新材料確認上)confirm Finance Department (FIN)加強;確認;批準(常用於對事情是否有確認)17.材料控制(物控)control panelMaterial Control (MC)(DAGGER機種的面板)18.生產控制(生管)follow-upProduction Control (PC)強制執行(對事情要確實實施)19.文件中心phase outDocument center 停用;或漸漸停產(用於機種或材料停用)20.研發處color uniformityR/D Division=Research/Disign Division 色度一致性(指差異值)(a).電氣設計部brightness uniformity B/UElectrical design dept 亮度一致性(指百分比差異值)技術支援課Technological support section Department 部門文件室1.產品工程部Document room Product Engineering Department(PE)(b).機構設計部2.測試工程部Mechanical design dept Test Engineering Department(TE)(c)專案管理部3.製造工程部Project Management DepartmentManufacture Engineering Department(ME)4.廠務工程部Factory Engineering Department(FE)5.資材部Material Department6.採購部Purchase Department7.人資部Human Resource Department8.自插部Auto Insertion Department9.品保部Quality Assurance Department10.進料品質管制In Coming Quality Control (IQC)11.製程品質管制In Process Quality Control (IPQC)12.出貨品質管制Out going Quality Control (OQC)13.品質工程Quality Engineering (QE)14.資訊部Management Information System(MIS)15.制造部Manufacturing Department (MFG)16.財務部第 13 頁 共 13 頁各部門中英文對照表第 12 頁 共 13 頁。
工业相关英语单词
工业相关英语单词一、工厂设施与设备类。
1. factory ['fæktri] n. 工厂。
2. plant [plɑːnt] n. 工厂；植物（在工业词汇中表示工厂）；vt. 种植；培养。
3. workshop ['wɜːkʃɒp] n. 车间。
4. machine [mə'ʃiːn] n. 机器。
5. equipment [ɪ'kwɪpmənt] n. 设备，装备（不可数名词）6. tool [tuːl] n. 工具。
7. conveyor [kən'veɪə(r)] n. 传送带；输送机。
8. generator ['dʒenəreɪtə(r)] n. 发电机。
二、工业生产过程类。
1. manufacture [ˌmænju'fæktʃə(r)] v. 制造；加工；n. 制造；制造业。
2. produce [prə'djuːs] v. 生产；制造；产生；n. 产品（尤指农产品）3. process ['prəʊses] n. 过程；工序；vt. 加工；处理。
4. assembly [ə'sembli] n. 装配；集会；集合。
5. quality control ['kwɒləti kən'trəʊl] 质量控制（名词短语）6. inspect [ɪn'spekt] vt. 检查；视察。
三、工业原料与产品类。
1. raw material [rɔː mə'tɪəriəl] 原材料（名词短语）2. product ['prɒdʌkt] n. 产品；结果。
3. component [kəm'pəʊnənt] n. 组件；成分；零部件。
4. metal ['metl] n. 金属。
四、工业人员类。
1. worker ['wɜːkə(r)] n. 工人。
工人英语单词
工人英语单词1. Worker –工人。
2. Occupation –职业。
3. Factory –工厂。
4. Manager –经理。
5. Employer –雇主。
6. Production –生产。
7. Workplace –工作场所。
8. Supervisor –监督者。
9. Security –安全。
10. Wage –工资。
11. Industrial –工业。
12. Expert –专家。
13. Health –健康。
14. Safety –安全。
15. Job –工作。
16. Manual –手工。
17. Retiree –退休人员。
18. Foreman –工头。
19. Technician –技术人员。
20. Craftsman –手艺人。
21. Mechanic –机械师。
22. Tradesperson –交易人员。
23. Administrator –管理人员。
24. Technician –技术人员。
25. Employee –雇员。
26. Craftsperson –技术工人。
27. Manufacturer –制造商。
28. Construction –建设。
29. Contractor –承包商。
30. Engineer –工程师。
31. Skilled –熟练。
32. Builder –建造者。
33. Factory Worker –工厂工人。
34. Welder –焊接工。
35. Electrician –电工。
36. Apprenticeship –学徒。
37. Assembly –组装。
38. Maintenance –维护。
39. Machine Operator –机械操作员。
40. Rigger –起重工。
41. Crane Operator –起重机操作员。
42. Driller –钻铁工。
43. Surveyor –测量员。
44. Laborer –劳工。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
1.机械与工厂英语组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs.inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS电源电压接柆键sheet metal parts 冲件plastic parts塑料件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager |'depjuti| =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embeded lump|in'bed| |l mp|镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over 切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cut edges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line stretching, line pulling线拉伸engraving, to engrave刻印up siding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerization装箱quantity of physical inventory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts 良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkali dipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compression molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5t11T=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality audit 合格供货商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 参照件FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸12DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QS Quality System 品质系统ES Engineering Standarization 工程标准H Huston (美国)休斯敦IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板13PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算器辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C/T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PC14A/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 操作系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size------------------------------------------------------------------------------------------模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻15hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧16cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧销goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道17。