机械专业英文翻译
机械设计专业术语的英语翻译要点
机械设计专业术语的英语译阿基米德蜗杆Archimedes worm平安系数safety factor;factor of safety平安载荷safe load凹面、凹度concavity扳手wrench板簧flat leafspring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower 摆动从动件凸轮机构cam wit h oscillating follower摆动导杆机构oscillating guide -bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profil 摆线运动规律cycloidal motio n 摆线针轮cycloidal-pin wheel 包角angle of contact保持架cage背对背安装back-to-back arran gement背锥back cone ; normal con e 背锥角back angle背锥品巨back cone distance 比例尺scale比热容specific heat capacity 闭式链closed kinematic chain 闭链机构closed chain mechan ism臂部arm变频器frequency converters 变频调速frequency control of motor speed变速speed change变速齿轮change gear ; chang e wheel变位齿轮modified gear变位系数modification coeffic ient标准齿轮standard gear标准直齿轮standard spur gear 外表质量系数superficial mass factor外表传热系数surface coefficie nt ofheat transfer外表粗糙度surface roughness 并联式组合combination in pa rallel并联机构parallel mechanism 并联组合机构parallel combinedmechanism并行工程concurrent engineeri ng并行设计concurred design, C D 不平衡相位phase angle of un balance不平衡imbalance (or unbalanc e)不平衡量amount of unbalanc e 不完全齿轮机构intermittent g earing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization d esign,PD剩余应力residual stress操纵及限制装置operation cont rol device槽车G Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train 差动螺旋机构differential scre w mechanism差速器differential常用机构conventional mechan ism; mechanism in common us e 车床lathe承载量系数bearing capacity f actor承载水平bearing capacity成对安装paired mounting尺寸系歹U dimension series齿槽tooth space 齿槽宽spacewidth 齿侧间隙backlash 齿顶高addendum 齿顶圆addendum circle 齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿品巨circular pitch齿宽face width齿廓tooth profile 齿廓曲线tooth curve 齿轮gear齿轮变速箱speed-changing ge ar boxes齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion -shaped shaper cutter 齿轮滚刀hob ,hobbing cutter 齿轮机构gear 齿轮轮坯blank 齿轮传动系pinion unit 齿轮联轴器gear coupling 齿条传动rack gear 齿数tooth number 齿数比gear ratio 齿条rack齿条插刀rack cutter; rack-sha ped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet m echanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speedratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft 串联式组合combination in se ries串联式组合机构series combin ed mechanism串级调速cascade speed contr ol仓惭innovation ; creation仓惭设计creation design垂直载荷、法向载荷normal l oad唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bea ring从动带轮driven pulley 从动件driven link, follower从动件平底宽度width of flat face从动件停歇follower dwell从动件运动规律follower moti on从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单歹U轴承single row bearing 单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear;virtual gear当量齿数equivalent teeth nu mber; virtual nu mber of teeth当量摩擦系数equivalent coeff icient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration anddeceleration motion等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radia l cam等宽凸轮constant-breadth ca m等效构件equivalent link等效力equivalent force等效力矩equivalent momentof force等效量equivalent等效质量equivalent mass 等效转动惯量equivalent mom ent of inertia等效动力学模型dynamically e quivalent model 底座chassis 彳氐副lower pair 点戈U线chain dotted line〔疲劳〕点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train;gear train with fixed axes 动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity 动力润滑dynamic lubrication 动平衡dynamic balance 动平衡机dynamic balancing machine动态特性dynamic characteristi cs动态分析设计dynamic analysis design动压力dynamic reaction 动载荷dynamic load 端面transverse plane 端面参数transverseparameters端面齿品巨transverse circular pi tch端面齿廓transverse tooth pro file 端面重合度transverse contactratio端面模数transverse module 端面压力角transverse pressur e angle锻造forge对称循环应力symmetry circul ating stress对心滚子从动件radial (or in-l ine ) roller follower对心直动从动件radial (or in-l ine ) translating follower对心移动从动件radial recipro cating follower对心曲柄滑块机构in-line slid er-crank (or crank-slider) mech anism多歹U轴承multi-row bearing 多楔带poly V-belt多项式运动规律polynomial m otion多质量转子rotor with several masses惰轮idle gear额定寿命rating life 额定载荷load rating II级杆组dyad 发生线generating line 发生面generating plane 法面normal plane法面参数normal parameters 法面齿品巨normal circular pitch 法面模数normal module 法面压力角normal pressure a ngle法向齿距normal pitch法向齿廓normal tooth profile 法向直廓蜗杆straight sided n ormal worm 法向力normal force反应式组合feedback combini ng反向运动学inverse ( or back ward) kinematics 反转法kinematic inversion 反正切Arctan范成法generating cutting 仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device 飞轮flywheel飞轮矩moment of flywheel 非标准齿轮nonstandard gear 非接触式密封non-contact seal 非周期性速度波动aperiodic s peed fluctuation非圆齿轮non-circular gear 粉末合金powder metallurgy 分度线reference line; standardpitch line分度圆reference circle; standa rd (cutting) pitch circle分度圆柱导程角lead angle atreference cylinder 分度圆柱螺旋角helix angle at refe rence cylinder分母denominator分子numerator分度圆锥reference cone; stan dard pitch cone分析法analytical method 封闭差动轮系planetary differential复合较链compound hinge复合式组合compound combi ning复合轮系compound (or comb ined) gear train复合平带compound flat belt复合应力combined stress 复式螺旋机构Compound scre w mechanism复杂机构complex mechanis m 杆组Assur group干预interference刚度系数stiffness coefficient 刚轮rigid circular spline钢丝软轴wire soft shaft 刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock) 刚性转子rigid rotor刚性轴承rigid bearing 刚性联轴器rigid coupling 高度系歹U height series 高速带high speed belt 高副higher pair格拉晓夫定理Grashoffs law根切undercutting公称直径nominal diameter高度系歹U height series功work工况系数application factor工艺设计technological design 工作循环图working cycle dia gram工作机构operation mechanism 工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance 工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyse s design共轲齿廓conjugate profiles共轲凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipul ator 惯性力inertia force惯性力矩moment of inertia ,s haking moment惯性力平衡balance of shakin g force惯性力完全平衡full balance of shaking force惯性力局部平衡partial balanc e of shaking force惯性主矩resultant moment of inertia惯性主失resultant vector of i nertia冠轮crown gear广义机构generation mechanis m广义坐标generalized coordinat e轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing i dentification code滚针needle roller滚针轴承needle roller bearing 滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller c hain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator 函数生成function generation 含油轴承oil bearing 耗油量oil consumption 耗油量系数oil consumption f actor赫兹公式H. Hertz equation 合成弯矩resultant bending m oment 合力resultant force合力矩resultant moment of f orce黑箱black box横坐标abscissa互换性齿轮interchangeable ge ars 花键spline滑键、导键feather key滑动轴承sliding bearing 滑动率sliding ratio 滑块slider环面蜗杆toroid helicoids wor m 环形弹簧annular spring缓冲装置shocks; shock-absorb smer灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear trai n积分integrate机电一体化系统设计mechani cal-electrical integration system design 机构mechanism机构分析analysis of mechanis m机构平衡balance of mechanis m 机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketc h of mechanism机构综合synthesis of mechani 机构组成constitution of mech anism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process 技术经济评价technical and e conomic evaluation技术系统technique system 机械machinery机械创新设计mechanical crea tion design, MCD机械系统设计mechanical syst em design, MSD机械动力分析dynamic analysi s of machinery机械动力设计dynamic design of machinery机械动力学dynamics of mach inery机械的现代设计modern mac hine design机械系统mechanical system 机械利益mechanical advantage机械平衡balance of machiner y机械手manipulator机械设计machine design; mec hanical design机械特性mechanical behavior 机械调速mechanical speed go vernors机械效率mechanical efficiency 机械原理theory of machines and mechanisms机械运转不均匀系数coefficie nt of speed fluctuation 机械无级变速mechanical stepl ess speed changes根底机构fundamental mechani sm根本额定寿命basic rating life基于实例设计case-baseddesig n,CBD基圆base circle基圆半径radius of base circle基圆齿品巨base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechani sm急回特性quick-return characte ristics急回系数advance-to return-ti me ratio急回运动quick-return motion棘车ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aid ed design, CAD计算机辅助制造computer aid ed manufacturing, CAM计算机集成制造系统compute r integrated manufacturing syst em, CIMS计算力矩factored moment; ca lculation moment计算弯矩calculated bending moment加权系数weighting efficient 力口速度acceleration力口速度分析acceleration analys is力口速度曲线acceleration diagra m尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent mo tion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile 渐开线齿轮involute gear 渐开线发生线generating lineof involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm 渐开线压力角pressure angle of involut e渐开线花键involute spline简谐运动simple harmonic mo tion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive 交错轴斜齿轮crossed helicalgears胶合scoring角力口速度angular acceleration 角速度angular velocity 角速比angular velocity ratio角接触球轴承angular contact ball bearin g角接触推力轴承angular conta ct thrust bearing角接触向心轴承angular conta ct radial bearing角接触轴承angular contact be aring钱链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal 阶梯轴multi-diameter shaft 结构structure结构设计structural design截面section节点pitch point节品巨circular pitch; pitch of te eth节线pitch line节圆pitch circle节圆齿厚thickness on pitch c ircle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design 紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equi valent radial load径向当量静载荷static equival ent radial load径向根本额定动载荷basic dy namic radial load rating径向根本额定静载荷basic sta tic radial load tating径向接触轴承radial contact b earing径向平面radial plane 径向游隙radial internal cleara nce径向载荷radial load径向载荷系数radial load fact or径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded for m 锯齿形螺纹buttress thread fo rm 矩形牙嵌式离合器square-jaw positive-contact clutch绝对尺寸系数absolute dimens ional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mech anism抗压弓®度compression strength开口传动open-belt drive 开式链open kinematic chain 开链机构open chain mechanism可靠度degree of reliability 可靠性reliability可靠性设计reliability design, RD 空气弹簧air spring空间机构spatial mechanism 空间连杆机构spatial linkage空间凸轮机构spatial cam 空间运动副spatial kinematic pair空间运动链spatial kinematic c hain空转idle宽度系列width series框图block diagram雷诺方程Reynolds ' s equation 离心力centrifugal force离心应力centrifugal stress 离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechani sm力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链车s sprocket ; sprocket-wheel ;sprocket gear ; chain wheel 联组V 带tight-up V belt联轴器coupling ; shaft coupli ng 两维凸轮two-dimensional cam 临界转速critical speed 六杆机构six-bar linkage 龙门包烁double Haas planer 轮坯blank 轮系gear train 螺杆screw 螺距thread pitch 螺母screw nut螺旋锥齿轮helical bevel gear螺车丁screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism 螺旋角helix angle螺旋线helix ,helical line 绿色设计green design ; desig n for environment马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross 脉动无级变速pulsating steples s speed changes脉动循环应力fluctuating circu lating stress脉动载荷fluctuating load 钏车丁rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component 密封装置sealing arrangement 面对面安装face-to-face arrang ement面向产品生命周期设计designfor product's life cycle, DPLC名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular syste m模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD 摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction 摩擦圆friction circle磨损abrasion ;wear; scratching 末端执行器end-effector目标函数objective function 而寸腐蚀性corrosion resistance 而寸磨性wear resistance挠性机构mechanism with flex ible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or a nticlockwise) 啮出engaging-out 啮合engagement, mesh, gearin g啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifyingpoint扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏〔心、〕品巨offset distance偏心率eccentricity ratio偏心质量eccentric mass 偏品巨圆offset circle偏心盘eccentric偏置滚子从动件offset roller f ollower偏置尖底从动件offset knife-e dgefollower偏置曲柄滑块机构offset slide r-crank mechanism 拼接matching评价与决策evaluation and de cision频率 frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diamete r平均速度average velocity 平衡balance平衡机balancing machine平衡品质balancing quality 平衡平面correcting plane 平衡质量balancing mass 平衡重counterweight 平衡转速balancing speed 平面副planar pair, flat pair 平面机构planar mechanism 平面运动副planar kinematic pair 平面连杆机构planar linkage 平面凸轮planar cam 平面凸轮机构planar cam mec hanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanis m in common use 起动阶段starting period 启动力矩starting torque气动机构pneumatic mechanis 奇异位置singular position起始啮合点initial contact ,beg inning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff s law 曲柄导杆机构crank shaper (g uide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism曲柄摇杆机构crank-rocker me chanism曲齿锥齿轮spiral bevel gear 曲率curvature曲率半径radius of curvature 曲面从动件curved-shoe follo wer曲线拼接curve matching曲线运动curvilinear motion 曲轴crank shaft驱动力driving force驱动力矩driving moment (tor que)全齿高whole depth 权重集weight sets 球ball球面滚子convex roller球轴承ball bearing 球面副spheric pair 球面渐开线spherical involute 球面运动spherical motion 球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition 热平衡heat balance; thermal e quilibrium人字齿轮herringbone gear 冗余自由度redundant degree of freedom柔轮flexspline 柔性冲击flexible impulse; soft shock柔性制造系统flexible manufa cturing system; FMS柔性自动化flexible automatio n 润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional ca m三心定理Kennedy's theorem 砂轮越程槽grinding wheel gr oove砂漏hour-glass少齿差行星传动planetary driv e with small teeth difference设计方法学design methodolohanism,设计变量design variable设计约束design constraints 深沟球轴承deep groove ball bearing 生产阻力productive resistance 升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham ' scoupling矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque 输出轴output shaft 输入构件input link 数学模型mathematic model 实际啮合线actual line of action双滑块机构double-slider mec ellipsograph 双曲柄机构double crank mec hanism双曲面齿轮hyperboloid gear 双头螺柱studs双万向联轴节constant-velocity (or double) universal joint双摇杆机构double rocker me chanism双转块机构Oldham coupling 双歹蚱由承double row bearing 双向推力轴承double-direction thrust bearing松边slack-side顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage 速度velocity速度不均匀(波动)系数co efficient of speed fluctuationgy速度波动 speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding moti on弹性联轴器elastic coupling ; flexible coupling弹性套柱销联轴器rubber-cus hioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form 特殊运动链special kinematicchain特性characteristics替代机构equivalent mechanis m 调节modulation, regulation 调心滚子轴承self-aligning roll er bearing调心球轴承self-aligning ball b earing调心轴承self-aligning bearing 调速speed governing调速电动机adjustable speed motors调速系统speed control syste m 调压调速variable voltage cont rol调速器regulator, governor铁磁流体密封ferrofluid seal停车阶段stopping phase停歇dwell同步带synchronous belt同步带传动synchronous belt drive凸的, 凸面体convex凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanis m 凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling 外齿轮external gear 弯曲应力beading stress 弯矩bending moment 腕部wrist往复移动reciprocating motion 往复式密封reciprocating seal 网上设计on-net design, OND 微动螺旋机构differential scre w mechanism位移displacement位移曲线displacement diagra m 位姿pose , position and orien tation稳定运转阶段steady motion period稳健设计robust design 蜗杆worm蜗杆传动机构worm gearing 蜗杆头数number of threads 蜗杆直径系数diametral quotie nt蜗杆蜗轮机构worm and wor m gear蜗杆形凸轮步进机构worm ca minterval mechanism 蜗杆旋向hands of worm 蜗轮worm gear 涡圈形盘簧power spring 无级变速装置stepless speed c hanges devices 无穷大infinite系杆crank arm, planet carrier现场平衡field balancing 向心轴承radial bearing 向心力centrifugal force 相对速度relative velocity 相对运动relative motion 相对间隙relative gap 象限quadrant 橡皮泥plasticine 细牙螺纹fine threads 销pin消耗consumption小齿轮pinion小径minor diameter橡胶弓M簧balata spring修正梯形加速度运动规律mo dified trapezoidal acceleration motion 修正正弦加速度运动规律mo dified sine acceleration motion 斜齿圆柱齿轮helical gear 斜键、钩头楔键taper key 泄漏leakage谐波齿轮harmonic gear 谐波传动harmonic driving 谐波发生器harmonic generator斜齿轮的当量直齿轮equivale nt spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to retur n-time ratio行星齿轮装置planetary trans mission行星轮planet gear行星轮变速装置planetary spe ed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechani sm虚拟现实virtual reality虚拟现实技术virtual reality te chnology, VRT虚拟现实设计virtual reality d esign, VRD虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; per missible stress悬臂名构cantilever structure 悬臂梁cantilever beam 循环功率流circulating powerload旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure压力中央center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) posi tive-contact coupling 雅可比矩阵Jacobi matrix 摇杆rocker液力传动hydrodynamic drive 液力耦合器hydraulic couplers 液体弹簧liquid spring液压无级变速hydraulic steples s speed changes液压机构hydraulic mechanism 一般化运动链generalized kine matic chain移动从动件reciprocating follo wer移动副prismatic pair, sliding pair移动关节prismatic joint 移动凸轮wedge cam 盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration应力图stress diagram应力一应变图stress-strain d iagram优化设计optimal design油杯oil bottle 油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension 有效圆周力effective circle force有害阻力detrimental resistanc e 余弦加速度运动cosine acceler ation (or simple harmonic) mo tion预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness 圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake 原动机prime mover 原始机构original mechanism 圆形齿轮circular gear 圆柱滚子cylindrical roller 圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barr el (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring 圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring 圆柱螺旋压缩弹簧cylindroid helical-coil compression spring 圆柱凸轮cylindrical cam 圆柱蜗杆cylindrical worm 圆柱坐标操作器cylindrical co ordinate manipulator圆锥螺旋扭转弹簧conoid heli cal-coil compression spring 圆锥滚子tapered roller圆锥滚子轴承tapered roller b earing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic prece pt design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation运动粘度kenematic viscosity载荷load载荷一变形曲线load—defo rmation curve载荷一变形图load—deform ation diagram窄V 带narrow V belt 毡圈密封felt ring seal 展成法generating 张紧力tension 张紧轮tension pulley 振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism 正向运动学direct (forward) ki nematics正弦机构sine generator, scotc h yoke 织布机100m正应力、法向应力normal stre ss制动器brake直齿圆柱齿轮spur gear 直齿锥齿轮straight bevel gear 直角三角形right triangle 直角坐标操作器Cartesian coo rdinate manipulator 直径系数diametral quotient 直径系歹U diameter series 直廓环面蜗杆hindley worm 直线运动linear motion 直轴straight shaft 质量mass 质心center of mass 执行构件executive link; worki ng link 质径积mass-radiusproduct 智能化设计intelligent design,ID中间平面mid-plane中央距 center distance中央闻巨变动center distance ch ange中央轮central gear中径mean diameter终止啮合点final contact, endof contact周节pitch周期性速度波动periodic spee d fluctuation周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承夕卜径bearing outside diam eter轴颈journal 轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equi valent axial load轴向当量静载荷static equival ent axial load轴向根本额定动载荷basic dy namic axial load rating轴向根本额定静载荷basic sta tic axial load rating轴向接触轴承axial contact be aring轴向平面axial plane轴向游隙axial internal clearan ce轴向载荷axial load主动件driving link主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mech anism转动副revolute (turning) pair转速swiveling speed ; rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装酉己条件assembly condition 锥齿轮bevel gear锥顶common apex of cone锥品巨cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivale 轴向载荷系数axial load facto r轴向分力axial thrust loadnt spurgear of the bevel gear 锥面包络圆柱蜗杆milled heli coids worm准双曲面齿轮hypoid gear子程序subroutine子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-loc king自由度degree of freedom, m obility总重合度total contact ratio总反力resultant force总效率combined efficiency; o verall efficiency组成原理theory of constitution组合齿形composite tooth for m 组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum differen ce work between plus and min us work 纵向重合度overlap contact ra 纵坐标ordinate组合机构combined mechanis m 最少齿数minimum teeth num ber最小向径minimum radius作用力applied force坐标系coordinate frametio。
机械专业英文翻译
机械专业英文翻译 Company number：【WTUT-WT88Y-W8BBGB-BWYTT-19998】启动轴 starting axle 启动齿轮starting gear启动棘轮 starting ratchet wheel 复位弹簧 restoring, pull back spring弹簧座 spring seating 摩擦簧friction spring推力垫圈 thrust washer 轴挡圈axle bumper ring下料 filling 切断 cut 滚齿机 gear-hobbing machine剪料机 material-shearingmachine车床 lathe 拉床broaching machine垂直度 verticality, verticalextent 平行度 parallelism同心度 homocentricity位置度 position拉伤 pulling damage碰伤 bumping damage缺陷 deficiency严重缺陷 severe deficiency摩擦力 friction 扭距 twist滑动 glide 滚动 roll打滑 skid 脱不开 can’t seperate不复位 can’t restore 直径 diameterM值 = 跨棒距 test rod span公法线 common normal line 弹性elasticity频率特性 frequency characteristic误差 error响应 response 定位 allocation 机床夹具 jig 动力学 dynamic运动学 kinematic静力学 static分析力学 analyse mechanics拉伸 pulling压缩 hitting机床 machine tool刀具 cutter摩擦 friction联结 link传动 drive/transmission轴 shaft剪切 shear扭转 twist弯曲应力 bending stress三相交流电 three-phase AC磁路 magnetic circles变压器 transformer异步电动机 asynchronous motor几何形状 geometrical精度 precision正弦形的 sinusoid交流电路 AC circuit机械加工余量 machining allowance变形力 deforming force变形 deformation电路 circuit半导体元件 semiconductor element拉孔 broaching装配 assembling加工 machining液压 hydraulic pressure切线 tangent机电一体化 mechanotronics mechanical-electrical integration稳定性 stability介质 medium液压驱动泵 fluid clutch 液压泵 hydraulic pump阀门 valve失效 invalidation强度 intensity载荷 load应力 stress安全系数 safty factor可靠性 reliability螺纹 thread螺旋 helix键 spline销 pin滚动轴承 rolling bearing滑动轴承 sliding bearing弹簧 spring制动器 arrester brake十字结联轴节 crosshead联轴器 coupling链 chain皮带 strap精加工 finish machining粗加工 rough machining变速箱体 gearbox casing腐蚀 rust氧化 oxidation磨损 wear耐用度 durability机械制图Mechanical drawing投影 projection视图 view剖视图 profile chart标准件 standard component零件图 part drawing装配图 assembly drawing尺寸标注 size marking技术要求technical requirements刚度 rigidity内力 internal force位移 displacement截面 section疲劳极限 fatigue limit断裂 fracture塑性变形 plastic distortion脆性材料 brittleness material刚度准则 rigidity criterion垫圈 washer垫片 spacer直齿圆柱齿轮straight toothed spur gear斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图 kinematic sketch齿轮齿条 pinion and rack蜗杆蜗轮 worm and worm gear虚约束 passive constraint曲柄 crank摇杆 racker凸轮 cams反馈 feedback发生器 generator直流电源 DC electrical source 门电路 gate circuit外圆磨削 external grinding内圆磨削 internal grinding平面磨削 plane grinding变速箱 gearbox离合器 clutch绞孔 fraising绞刀 reamer螺纹加工 thread processing螺钉 screw铣削 mill铣刀 milling cutter功率 power工件 workpiece齿轮加工 gear mechining齿轮 gear主运动 main movement主运动方向direction of main movement进给方向 direction of feed进给运动 feed movement合成进给运动resultant movement of feed合成切削运动resultant movement of cutting合成切削运动方向 directionof resultant movement of cutting 切削深度 cutting depth前刀面 rake face刀尖 nose of tool前角 rake angle后角 clearance angle龙门刨削 planing主轴 spindle主轴箱 headstock卡盘 chuck加工中心 machining center车刀 lathe tool车床 lathe镗削 bore集成电路 integrate circuit挡板 orifice plate残余应力 residual stress套筒 sleeve扭力 torsion 冷加工 cold machining电动机 electromotor汽缸 cylinder过盈配合 interference fit热加工 hotwork摄像头 CCD camera倒角 rounding chamfer优化设计 optimal design工业造型设计industrial moulding design有限元 finite element滚齿 hobbing插齿 gear shaping伺服电机 actuating motor铣床 milling machine钻床 drill machine镗床 boring machine步进电机 stepper motor丝杠 screw rod导轨 lead rail组件 subassembly可编程序逻辑控制器Programmable LogicController PLC毛坯 rough桁架 truss轴线 axes逻辑电路 logic circuit触发器 flip-flop脉冲波形 pulse shape数模 digital analogy液压传动机构fluid drive mechanism机械零件 mechanical parts产品突出特点ProductHighlights特别优惠 special offersAssembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor 副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skrpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块barreling 滚光加工 belling 压凸加工bending 弯曲加工 blanking 下料加工bulging 撑压加工 burring 冲缘加工cam die bending 凸轮弯曲加工caulking 合加工coining 压印加工 compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工 dinking 切断蕊骨double shearing 叠板裁断 drawing 引伸加工drawing with ironing 抽引光滑加工 embossing 浮花压制加工extrusion 挤制加工 filing 锉削加工fine blanking 精密下料加工 finish blanking 光制下料加工finishing 精整加工 flanging 凸缘加工folding 折边弯曲加工 folding 摺叠加工forming 成形加工 impact extrusion 冲击挤压加工indenting 压痕加工 ironing 引缩加工knurling 滚花 lock seaming 固定接合louvering 百叶窗板加工 marking 刻印加工necking 颈缩加工 notching 冲口加工parting 分断加工 piercing 冲孔加工progressive bending 连续弯曲加工 progressiveblanking 连续下料加工progressive drawing 连续引伸加工 progressiveforming 连续成形加工reaming 铰孔加工 restriking 二次精冲加工riveting 接加工 roll bending 滚筒弯曲加工roll finishing 滚压加工 rolling 压延加工roughing 粗加工 scrapless machining 无废料加工seaming 折弯重叠加工 shaving 缺口修整加工shearing 切断加工 sizing 精压加工/矫正加工slitting 割缝加工 spinning 卷边接staking 固 stamping 锻压加工swaging 挤锻压加工 trimming 整缘加工upsetting 锻粗加工 wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴 blank determination 胚料展开bottom slide press 下传动式压力机 board drophammer 板落锤brake 煞车 buckle 剥砂面camlachie cramp 铸包 casting on flat 合chamotte sand 烧磨砂 charging hopper 加料漏斗clearance 间隙 closed-die forging 合模锻造clump 夹紧 clutch 离合器clutch brake 离合器制动器 clutch boss 离合器轮壳clutch lining 离合器覆盖 coil car 带卷升降运输机coil cradle 卷材进料装置 coil reel stand 钢材卷料架column 圆柱 connection screw 连杆调节螺钉core compound 砂心黏结剂 counter blow hammer 对击锻锤cradle 送料架 crank 曲柄轴crankless 无曲柄式 cross crank 横向曲轴cushion 缓冲 depression 外缩凹孔dial feed 分度送料 die approach 模口角度die assembly 合模 die cushion 模具缓冲垫die height 冲压闭合高度 die life 模具寿命die opening 母模逃孔 die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床 draght angle 逃料倾斜角edging 边锻伸 embedded core 加装砂心feed length 送料长度 feed level 送料高度filling core 埋入砂心 filling in 填砂film play 液面花纹 fine blanking press 精密下料冲床forging roll 辊锻机 finishing slag 炼後熔渣fly wheel 飞轮 fly wheel brake 飞轮制动器foot press 脚踏冲床 formboard 进模口板frame 床身机架 friction 摩擦friction brake 摩擦煞车 gap shear 凹口剪床gear 齿轮 gib 滑块引导部gripper 夹具 gripper feed 夹持进料gripper feeder 夹紧传送装置 hammer 槌机hand press 手动冲床 hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床 hopper feed 料斗送料idle stage 空站 inching 微调尺寸isothermal forging 恒温锻造 key clutch 键槽离合器knockout 脱模装置 knuckle mechanic 转向机构land 模具直线刀面部 level 水平loader 供料器 unloader 卸料机loop controller 闭回路控制器 lower die 下模micro inching device 微寸动装置 microinching equipment 微动装置motor 马达 moving bolster 活动工作台notching press 冲缺口压力机 opening 排料逃孔overload protection device 防超载装置 pinch roll 导正滚轮pinion 小齿轮 pitch 节距pressfit 压入 progressive 连续送料pusher feed 推杆式送料 pusher feeder 料片押片装置quick die change system 快速换模系统 regrinding 再次研磨releasing 松释动作 reversedblanking 反转下料robot 机器人 roll formingmachine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料 roller leveler辊式矫直机rotary bender 卷弯成形机 safetyguard 安全保护装置scrap cutter 废料切刀 scrap press废料冲床seamless forging 无缝锻造separate 分离shave 崩砂 shear angle 剪角sheet loader 薄板装料机 shot 单行程工作shrinkage fit 收缩配合 shutheight 闭合高度sieve mesh 筛孔 sintering of sand铸砂烧贴slide balancer 滑动平衡器 slughole 逃料孔spin forming machine 旋压成形机 spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程 take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机 vibration feeder振动送料机wiring press 嵌线卷边机业务与贸易关连用语accept order 接受订货 account 帐户after service 售后服务 amendment 修正annual sales 年销售额 at sight 见票即付balance 余额 bank draft 汇票bargain goods 廉价品 batch 批次bid 出价 bid sales 投标买卖bill of landing 提单 bills receivable 应收票据brand 品牌 bulk cargo 散装货business transaction 商业交易 buyer 买方carbon copy 打字副本 cargo collection 揽货carton 纸箱 cash in advance 预付现金catalogue 型录 cheque 支票CLF 运费保险费在内价格 claim 索赔clearance goods 清仓品 commision 佣金commission 批发商 complain 抱怨container 货柜 correspondence bank 往来银行cost 成本 cost and freight; C&F 含运费价格custom broker 报关行 customer 客户D/A 承兑交单 D/P 付款交单deferred payment 分期付款 deferred shipment 分期装运delivery on spot 当场交货 delivery time 交期delivery order 交货单 discount 折扣discount on draft 贴现 documentary draft 跟单汇票down payment 订金 enclosure 附件endorsement 背书 enquete 调查exhibition 展览会 export 出口factory visiy 工厂参观 favourable price 合宜价格foreign exchange 外汇 free on board 船上交货价idea price 希望价格 import 进口Japanese Industrial 日本工业规格 invoice 发票L/C 信用状 margin 利润market 市价 net weight 净重no payment 拒绝付款 odd item 零头offer 报价 open account 交互计算order 订单 over looked 疏漏packing 包装 pamphlet 小册子partial shipment 分批装船 patent 专利paying price 合算价格 payment method 付款方式port of destination 目地港 port of trans-shipment转口港price 价格 price decending 减价price rising 涨价 procurement 采办prompt delivery 即时交货 purchase 购入purchasing agent 采购代理商 quotation 报价单rebate 回扣 reference 查询remittance 汇款 repeat order 追加订货request letter 请求函 rumor 风评second hand goods 二手货 shipper 货主shipping 装船 shipping mark 麦头shipment 出货 sold out 卖完sole agent 总代理商 special discount 特别折扣specification 规格 sample order 指样订货standing 信用情形 storage charge 仓租subcontract 外包 subject to final confirmation 有待确认之报价supplier 供应商 T/T 电汇tie-in sale 搭售 trade fair 商展会trans-shipment 转运 transferred 已转运wharf 码头。
机械设计专业术语的英语翻译
表面质量系数 superficial mass factor
表面传热系数 surface coefficient of heat transfer
表面粗糙度 surface roughness
并联式组合 combination in parallel
齿厚 tooth thickness
齿距 circular pitch
齿宽 face width
齿廓 tooth profile
齿廓曲线 tooth curve
齿轮 gear
齿轮变速箱 speed-changing gear boxes
齿轮齿条机构 pinion and rack
齿轮插刀 pinion cutter; pinion-shaped shaper cutter
齿轮滚刀 hob ,hobbing cutter
齿轮机构 gear
齿轮轮坯 blank
齿轮传动系 pinion unit
齿轮联轴器 gear coupling
齿条传动 rack gear
齿数 tooth number
齿数比 gear ratio
齿条 rack
齿条插刀 rack cutter; rack-shaped shaper cutter
操纵及控制装置 operation control device
槽轮 Geneva wheel
槽轮机构 Geneva mechanism ； Maltese cross
槽数 Geneva numerate
槽凸轮 groove cam
侧隙 backlash
各专业英文翻译
法学 Law Study英语 English日语 Japanese信息与计算科学 Information and Computation Science应用物理学 Applied Physics冶金工程 Metallurgical Engineering金属材料工程 Metallic Materials Engineering无机非金属材料 Inorganic Nonmetallic Materials材料成型及控制工程 Material Formation and controlEngineering高分子材料与工程 Multimolecular Materials and Engineering工业设计 Industrial Disign建筑学 Architecture城市规划 City Planning艺术设计 Artistical Disign包装工程 Packaging Engineering机械设计制造及自动化Machine Disign,Manufacturing,and Automation热能与动力工程 Thermal and Power Engineering水利水电工程 WaterConservance and Electro-power Engineering测控技术与仪器 Technique and Instrumentation of Measurements电气工程及其自动化 Electric Engineering and its Automation自动化 Automation通信工程 Communication Engineering电子信息科学与技术 Sience and Technology of Electronic Information 计算机科学与技术 Computer Sience and Technology土木工程 Civil Engineering工程管理 Project Management给水排水工程 Water Supply and Sewage Engineering建筑环境与设备工程 Constructional Environment and Equipment Engineering 过程装备与控制工程 Processing Units and Control Engineering环境工程 Environmental Engineering化学工程与工艺 Chemacal Engineering and Technology安全工程 Safty Engineering工商管理 Industrial and Commercial Management市场营销 Market Management and Sales会计学 Accounting旅游管理 Tourism Management信息管理与信息系统 Information Management and System金融学 Finance国际经济与贸易 International Economy and Trade食品科学与工程 Food Sience and Engineering生物工程 Biological Engineering纺织工程 Textile Engineering建筑环境与设备工程、Constructional Environment and Equipment Engineering 过程装备与控制工程、Processing Units and Control Engineering现代家政学、 Modern Domestic Science运动训练科学系、 Sports Train Science食品营养与检测、 Food Nutrition and Detect国际新闻、 International News体育健康教育系 Sports Health Education哲学 Philosophy马克思主义哲学 Philosophy of Marxism中国哲学 Chinese Philosophy外国哲学 Foreign Philosophies逻辑学 Logic伦理学 Ethics美学 Aesthetics宗教学 Science of Religion科学技术哲学 Philosophy of Science and Technology经济学 Economics理论经济学 Theoretical Economics政治经济学 Political Economy经济思想史 History of Economic Thought经济史 History of Economic西方经济学 Western Economics世界经济 World Economics人口、资源与环境经济学 Population, Resources and Environmental Economics应用经济学 Applied Economics国民经济学 National Economics区域经济学 Regional Economics财政学（含税收学） Public Finance (including Taxation)金融学（含保险学） Finance (including Insurance)产业经济学 Industrial Economics国际贸易学 International Trade劳动经济学 Labor Economics统计学 Statistics数量经济学 Quantitative Economics中文学科、专业名称英文学科、专业名称国防经济学 National Defense Economics法学 Law法学 Science of Law法学理论 Jurisprudence法律史 Legal History宪法学与行政法学 Constitutional Law and Administrative Law 刑法学 Criminal Jurisprudence民商法学(含劳动法学、社会保障法学) Civil Law and Commercial Law (including Science of Labour Law and Science of Social Security Law )诉讼法学 Science of Procedure Laws经济法学 Science of Economic Law环境与资源保护法学 Science of Environment and Natural Resources Protection Law国际法学(含国际公法学、国际私法学、国际经济法学、) International law (including International Public law, International Private Law and International Economic Law)军事法学 Science of Military Law政治学 Political Science政治学理论 Political Theory中外政治制度 Chinese and Foreign Political Institution科学社会主义与国际共产主义运动 Scientific Socialism and InternationalCommunist Movement中*史(含党的学说与党的建设) History of the Communist Party of China(including the Doctrine of China Party and Party Building) 马克思主义理论与思想政治教育 Education of Marxist Theory and Education in Ideology and Politics国际政治学 International Politics国际关系学 International Relations外交学 Diplomacy社会学 Sociology社会学 Sociology人口学 Demography人类学 Anthropology民俗学(含中国民间文学) Folklore (including Chinese Folk Literature)民族学 Ethnology民族学 Ethnology马克思主义民族理论与政策 Marxist Ethnic Theory and Policy 中国少数民族经济 Chinese Ethnic Economics中国少数民族史 Chinese Ethnic History中国少数民族艺术 Chinese Ethnic Art教育学 Education教育学 Education Science教育学原理 Educational Principle课程与教学论 Curriculum and Teaching Methodology教育史 History of Education比较教育学 Comparative Education学前教育学 Pre-school Education高等教育学 Higher Education成人教育学 Adult Education职业技术教育学 Vocational and Technical Education特殊教育学 Special Education教育技术学 Education Technology心理学 Psychology基础心理学 Basic Psychology发展与心理学 Developmental and Educational Psychology应用心理学 Applied Psychology体育学 Science of Physical Culture and Sports体育人文社会学 Humane and Sociological Science of Sports 运动人体科学 Human Movement Science体育教育训练学 Theory of Sports Pedagogy and Training民族传统体育学 Science of Ethnic Traditional Sports文学 Literature中国语言文学 Chinese Literature文艺学 Theory of Literature and Art语言学及应用语言学 Linguistics and Applied Linguistics汉语言文字学 Chinese Philology中国古典文献学 Study of Chinese Classical Text中国古代文学 Ancient Chinese Literature中国现当代文学 Modern and Contemporary Chinese Literature 中国少数民族语言文学 Chinese Ethnic Language and Literature比较文学与世界文学 Comparative Literature and World Literature外国语言文学 Foreign Languages and Literatures英语语言文学 English Language and Literature俄语语言文学 Russian Language and Literature法语语言文学 French Language and Literature德语语言文学 German Language and Literature日语语言文学 Japanese Language and Literature印度语言文学 Indian Language and Literature西班牙语语言文学 Spanish Language and Literature阿拉伯语语言文学 Arabic Language and Literature欧洲语言文学 European Language and Literature亚非语言文学 Asian-African Language and Literature外国语言学及应用语言学 Linguistics and Applied Linguistics in Foreign Languages新闻传播学 Journalism and Communication新闻学 Journalism传播学 Communication艺术学 Art艺术学 Art Theory音乐学 Music美术学 Fine Arts设计艺术学 Artistic Design戏剧戏曲学 Theater and Chinese Traditional Opera电影学 Film广播电视艺术学 Radio and television Art舞蹈学 Dance历史学 History历史学 History史学理论及史学史 Historical Theories and History of Historical Science考古学及博物馆学 Archaeology and Museology历史地理学 Historical Geography历史文献学(含敦煌学、古文字学) Studies of Historical Literature (includingPaleography and Studies of Dunhuang)专门史 History of Particular Subjects中国古代史 Ancient Chinese History中国近现代史 Modern and Contemporary Chinese History世界史 World History理学 Natural Science数学 Mathematics基础数学 Fundamental Mathematics计算数学 Computational Mathematics概率论与数理统计 Probability and Mathematical Statistics 应用数学 Applied mathematics运筹学与控制论 Operational Research and Cybernetics物理学 Physics理论物理 Theoretical Physics粒子物理与原子核物理 Particle Physics and Nuclear Physics原子与分子物理 Atomic and Molecular Physics等离子体物理 Plasma Physics凝聚态物理 Condensed Matter Physics声学 Acoustics光学 Optics无线电物理 Radio Physics化学 Chemistry无机化学 Inorganic Chemistry分析化学 Analytical Chemistry有机化学 Organic Chemistry物理化学（含化学物理） Physical Chemistry (including Chemical Physics)高分子化学与物理 Chemistry and Physics of Polymers天文学 Astronomy天体物理 Astrophysics天体测量与天体力学 Astrometry and Celestial Mechanics地理学 Geography自然地理学 Physical Geography人文地理学 Human Geography地图学与地理信息系统 Cartography and Geography Information System大气科学 Atmospheric Sciences气象学 Meteorology大气物理学与大气环境 Atmospheric Physics and Atmospheric Environment海洋科学 Marine Sciences物理海洋学 Physical Oceanography海洋化学 Marine Chemistry海洋生理学 Marine Biology海洋地质学 Marine Geology地球物理学 Geophysics固体地球物理学 Solid Earth Physics空间物理学 Space Physics地质学 Geology矿物学、岩石学、矿床学 Mineralogy, Petrology, Mineral Deposit Geology地球化学 Geochemistry古生物学与地层学（含古人类学） Paleontology and Stratigraphy (including Paleoanthropology)构造地质学 Structural Geology第四纪地质学 Quaternary Geology生物学 Biology植物学 Botany动物学 Zoology生理学 Physiology水生生物学 Hydrobiology微生物学 Microbiology神经生物学 Neurobiology遗传学 Genetics发育生物学 Developmental Biology细胞生物学 Cell Biology生物化学与分子生物学 Biochemistry and Molecular Biology 生物物理学 Biophysics生态学 Ecology系统科学 Systems Science系统理论 Systems Theory系统分析与集成 Systems Analysis and Integration科学技术史 History of Science and Technology工学 Engineering力学 Mechanics一般力学与力学基础 General and Fundamental Mechanics固体力学 Solid Mechanics流体力学 Fluid Mechanics工程力学 Engineering Mechanics机械工程 Mechanical Engineering机械制造及其自动化 Mechanical Manufacture and Automation 机械电子工程 Mechatronic Engineering机械设计与理论 Mechanical Design and Theory车辆工程 Vehicle Engineering光学工程 Optical Engineering仪器科学与技术 Instrument Science and Technology精密仪器及机械 Precision Instrument and Machinery测试计量技术及仪器 Measuring and Testing Technologies and Instruments材料科学与工程 Materials Science and Engineering材料物理与化学 Materials Physics and Chemistry材料学 Materialogy材料加工工程 Materials Processing Engineering冶金工程 Metallurgical Engineering冶金物理化学 Physical Chemistry of Metallurgy钢铁冶金 Ferrous Metallurgy有色金属冶金 Non-ferrous Metallurgy动力工程及工程热物理 Power Engineering and Engineering Thermophysics工程热物理 Engineering Thermophysics热能工程 Thermal Power Engineering动力机械及工程 Power Machinery and Engineering流体机械及工程 Fluid Machinery and Engineering制冷及低温工程 Refrigeration and Cryogenic Engineering化工过程机械 Chemical Process Equipment电气工程 Electrical Engineering电机与电器 Electric Machines and Electric Apparatus电力系统及其自动化 Power System and its Automation高电压与绝缘技术 High Voltage and Insulation Technology 电力电子与电力传动 Power Electronics and Power Drives电工理论与新技术 Theory and New Technology of Electrical Engineering电子科学与技术 Electronics Science and Technology物理电子学 Physical Electronics电路与系统 Circuits and Systems微电子学与固体电子学 Microelectronics and Solid State Electronics电磁场与微波技术 Electromagnetic Field and Microwave Technology信息与通信工程 Information and Communication Engineering 通信与信息系统 Communication and Information Systems信号与信息处理 Signal and Information Processing控制科学与工程 Control Science and Engineering控制理论与控制工程 Control Theory and Control Engineering检测技术与自动化装置 Detection Technology and Automatic Equipment系统工程 Systems Engineering模式识别与智能系统 Pattern Recognition and Intelligent Systems导航、制导与控制 Navigation, Guidance and Control计算机科学与技术 Computer Science and Technology计算机软件与理论 Computer Software and Theory计算机系统结构 Computer Systems Organization计算机应用技术 Computer Applied Technology建筑学 Architecture建筑历史与理论 Architectural History and Theory建筑设计及其理论 Architectural Design and Theory城市规划与设计（含风景园林规划与设计） Urban Planning and Design (including Landscape Planning and Design)建筑技术科学 Building Technology Science土木工程 Civil Engineering岩土工程 Geotechnical Engineering结构工程 Structural Engineering市政工程 Municipal Engineering供热、供燃气、通风及空调工程 Heating, Gas Supply, Ventilating and Air Conditioning Engineering防灾减灾工程及防护工程 Disaster Prevention and Reduction Engineering and Protective Engineering桥梁与隧道工程 Bridge and Tunnel Engineering水利工程 Hydraulic Engineering水文学及水资源 Hydrology and Water Resources水力学及河流动力学 Hydraulics and River Dynamics水工结构工程 Hydraulic Structure Engineering水利水电工程 Hydraulic and Hydro-Power Engineering港口、海岸及近海工程 Harbor, Coastal and Offshore Engineering 测绘科学与技术 Surveying and Mapping大地测量学与测量工程 Geodesy and Survey Engineering摄影测量与遥感 Photogrammetry and Remote Sensing地图制图学与地理信息工程 Cartography and Geographic Information Engineering化学工程与技术 Chemical Engineering and Technology化学工程 Chemical Engineering化学工艺 Chemical Technology生物化工 Biochemical Engineering应用化学 Applied Chemistry工业催化 Industrial Catalysis地质资源与地质工程 Geological Resources and Geological Engineering矿产普查与勘探 Mineral Resource Prospecting and Exploration 地球探测与信息技术 Geodetection and Information Technology 地质工程 Geological Engineering矿业工程 Mineral Engineering采矿工程 Mining Engineering矿物加工工程 Mineral Processing Engineering安全技术及工程 Safety Technology and Engineering石油与天然气工程 Oil and Natural Gas Engineering油气井工程 Oil-Gas Well Engineering油气田开发工程 Oil-Gas Field Development Engineering油气储运工程 Oil-Gas Storage and Transportation Engineering 纺织科学与工程 Textile Science and Engineering纺织工程 Textile Engineering纺织材料与纺织品设计 Textile Material and Textiles Design纺织化学与染整工程 Textile Chemistry and Dyeing and Finishing Engineering服装设计与工程 Clothing Design and Engineering轻工技术与工程 The Light Industry Technology and Engineering 制浆造纸工程 Pulp and Paper Engineering制糖工程 Sugar Engineering发酵工程 Fermentation Engineering皮革化学与工程 Leather Chemistry and Engineering交通运输工程 Communication and Transportation Engineering道路与铁道工程 Highway and Railway Engineering交通信息工程及控制 Traffic Information Engineering & Control 交通运输规划与管理 Transportation Planning and Management载运工具运用工程 Vehicle Operation Engineering船舶与海洋工程 Naval Architecture and Ocean Engineering船舶与海洋结构物设计制造 Design and Construction of Naval Architecture and Ocean Structure轮机工程 Marine Engine Engineering水声工程 Underwater Acoustics Engineering航空宇航科学与技术 Aeronautical and Astronautical Science and Technology飞行器设计 Flight Vehicle Design航空宇航推进理论与工程 Aerospace Propulsion Theory and Engineering航空宇航器制造工程 Manufacturing Engineering of Aerospace Vehicle人机与环境工程 Man-Machine and Environmental Engineering兵器科学与技术 Armament Science and Technology武器系统与运用工程 Weapon Systems and Utilization Engineering 兵器发射理论与技术 Armament Launch Theory and Technology火炮、自动武器与弹药工程 Artillery, Automatic Gun and Ammunition Engineering军事化学与烟火技术 Military Chemistry and Pyrotechnics核科学与技术 Nuclear Science and Technology核能科学与工程 Nuclear Energy Science and Engineering核燃料循环与材料 Nuclear Fuel Cycle and Materials核技术及应用 Nuclear Technology and Applications辐射防护及环境保护 Radiation and Environmental Protection农业工程 Agricultural Engineering农业机械化工程 Agricultural Mechanization Engineering农业水土工程 Agricultural Water-Soil Engineering农业生物环境与能源工程 Agricultural Biological Environmental and Energy Engineering农业电气化与自动化 Agricultural Electrification and Automation林业工程 Forestry Engineering森林工程 Forest Engineering木材科学与技术 Wood Science and Technology林产化学加工工程 Chemical Processing Engineering of Forest Products环境科学与工程 Environmental Science and Engineering环境科学 Environmental Science环境工程 Environmental Engineering生物医学工程 Biomedical Engineering食品科学与工程 Food Science and Engineering食品科学 Food Science粮食、油脂及植物蛋白工程 Cereals, Oils and Vegetable Protein Engineering农产品加工及贮藏工程 Processing and Storage of Agriculture Products水产品加工及贮藏工程 Processing and Storage of Aquatic Products农学 Agriculture作物学 Crop Science作物栽培学与耕作学 Crop Cultivation and Farming System作物遗传育种学 Crop Genetics and Breeding园艺学 Horticulture果树学 Pomology蔬菜学 Olericulture茶学 Tea Science农业资源利用学 Utilization Science of Agricultural Resources 土壤学 Soil Science植物营养学 Plant Nutrition植物保护学 Plant Protection植物病理学 Plant Pathology农业昆虫与害虫防治 Agricultural Entomology and Pest Control 农药学 Pesticide Science畜牧学 Animal Science动物遗传育种与繁殖 Animal Genetics, Breeding and Reproduction Science动物营养与饲料科学 Animal Nutrition and Feed Science草业科学 Practaculture Science特种经济动物饲养学（含蚕、蜂等） The Rearing of Special-type EconomicAnimals (including Silkworm, Honeybees, etc.)兽医学 Veterinary Medicine基础兽医学 Basic Veterinary Medicine预防兽医学 Preventive Veterinary Medicine临床兽医学 Clinical Veterinary Medicine林学 Forestry林木遗传育种学 Forest Tree Genetics and Breeding森林培育学 Silviculture森林保护学 Forest Protection森林经理学 Forest Management野生动植物保护与利用 Wildlife Conservation and Utilization 园林植物与观赏园艺 Ornamental Plants and Horticulture水土保持与荒漠化防治 Soil and Water Conservation and Desertification Combating水产学 Fisheries Science水产养殖学 Aquaculture Science捕捞学 Fishing Science渔业资源学 Science of Fisheries Resources医学 Medicine基础医学 Basic Medicine人体解剖与组织胚胎学 Human Anatomy, Histology and Embryology 免疫学 Immunology病原生物学 Pathogenic Organisms病理学与病理生理学 Pathology and Pathophysiology法医学 Forensic Medicine放射医学 Radiation Medicine航空航天与航海医学 Aerospace and Nautical medicine临床医学 Clinical Medicine内科学（含心血管病学、血液病学、呼吸系病学、消化系病学、内分泌与代谢病学、肾脏病学、风湿病学、传染病学） Internal medicine (including Cardiology, Hematology, Respiratory, Gastroenterology, Endocrinology and Metabolism, Nephrology, Rheuma-tology, Infectious Diseases)儿科学 Pediatrics老年医学 Geriatrics神经病学 Neurology精神病与精神卫生学 Psychiatry and Mental Health皮肤病与性病学 Dermatology and Venereology影像医学与核医学 Imaging and Nuclear Medicine临床检验诊断学 Clinical Laboratory Diagnostics护理学 Nursing外科学（含普通外科学、骨外科学、泌尿外科学、胸心血管外科学、神经外科学、整形外科学、烧伤外科学、野战外科学） Surgery (General Surgery, Orthopedics, Urology, Cardiothoracic Surgery, Neurosurgery, Plastic Surgery, Burn Surgery, Field Surgery)妇产科学 Obstetrics and Gynecology眼科学 Ophthalmic Specialty耳鼻咽喉科学 Otolaryngology肿瘤学 Oncology康复医学与理疗学 Rehabilitation Medicine & Physical Therapy 运动医学 Sports Medicine麻醉学 Anesthesiology急诊医学 Emergency Medicine口腔医学 Stomatology口腔基础医学 Basic Science of Stomatology口腔临床医学 Clinical Science of Stomatology公共卫生与预防医学 Public Health and Preventive Medicine 流行病与卫生统计学 Epidemiology and Health Statistics劳动卫生与环境卫生学 Occupational and Environmental Health 营养与食品卫生学 Nutrition and Food Hygiene儿少卫生与妇幼保健学 Maternal, Child and Adolescent Health 卫生毒理学 Hygiene Toxicology军事预防医学 Military Preventive Medicine中医学 Chinese Medicine中医基础理论 Basic Theories of Chinese Medicine中医临床基础 Clinical Foundation of Chinese Medicine中医医史文献 History and Literature of Chinese Medicine方剂学 Formulas of Chinese Medicine中医诊断学 Diagnostics of Chinese Medicine中医内科学 Chinese Internal Medicine中医外科学 Surgery of Chinese Medicine中医骨伤科学 Orthopedics of Chinese Medicine中医妇科学 Gynecology of Chinese Medicine中医儿科学 Pediatrics of Chinese Medicine中医五官科学 Ophthalmology and Otolaryngoloy of Chinese Medicine针灸推拿学 Acupuncture and Moxibustion and Tuina of Chinese medicine民族医学 Ethnomedicine中西医结合医学 Chinese and Western Integrative Medicine中西医结合基础医学 Basic Discipline of Chinese and Western Integrative中西医结合临床医学 Clinical Discipline of Chinese and Western Integrative Medicine药学 Pharmaceutical Science药物化学 Medicinal Chemistry药剂学 Pharmaceutics生药学 Pharmacognosy药物分析学 Pharmaceutical Analysis微生物与生化药学 Microbial and Biochemical Pharmacy药理学 Pharmacology中药学 Science of Chinese Pharmacology军事学 Military Science军事思想学及军事历史学 Military Thought and Military History 军事思想学 Military Thought军事历史学 Military History战略学 Science of Strategy军事战略学 Military Strategy战争动员学 War Mobilization战役学 Science of Operations联合战役学 Joint Operation军种战役学（含第二炮兵战役学） Armed Service Operation (including Operation of Strategic Missile Force)战术学 Science of Tactics合同战术学 Combined-Arms Tactics兵种战术学 Branch Tactics军队指挥学 Science of Command作战指挥学 Combat Command军事运筹学 Military Operation Research军事通信学 Military Communication军事情报学 Military Intelligence密码学 Cryptography军事教育训练学（含军事体育学） Military Education and Training (including Military Physical Training)军制学 Science of Military System军事组织编制学 Military Organizational System军队管理学 Military Management军队政治工作学 Science of Military Political Work军事后勤学与军事装备学 Science of Military Logistics and Military Equipment军事后勤学 Military Logistics后方专业勤务 Rear Special Service军事装备学 Military Equipment管理学 Management Science管理科学与工程 Management Science and Engineering工商管理学 Science of Business Administration会计学 Accounting企业管理学（含财务管理、市场营销学、人力资源管理学） Corporate Management (including Financial Management, Marketing, and Human Resources Management)旅游管理学 Tourist Management技术经济及管理学 Technology Economy and Management农林经济管理学 Agricultural and Forestry Economics & Management农业经济管理学 Agricultural Economics & Management林业经济管理学 Forestry Economics & Management公共管理学 Science of Public Management行政管理学 Administration Management社会医学与卫生事业管理学 Social Medicine and Health Management教育经济与管理学 Educational Economy and Management社会保障学 Social Security土地资源管理学 Land Resource Management图书馆、情报与档案学 Science of Library, Information and Archival图书馆学 Library Science情报学 Information Science档案学 Archival Science。
机械工程学专业词汇英语翻译（V）
vacancy 空位 vacant site 空位 vacuum 真空 vacuum apparatus 真空装置 vacuum chamber 真空室 vacuum diagram 真空图 vacuum diffusion 真空扩散 vacuum effect 真空效应 vacuum pump 真空泵 vacuum state 真空态 vacuum tank 真空罐 vacuum tight 真空密闭的 vacuum value of velocity 真空速度 vacuum valve 真空阀 vacuum vector 真空⽮量 validity 有效性 validity criteria 有效准则 valley floor ⾕底 value 值 valve lift 阀升程 valve lift curve 阀升距图 valve lift diagram 阀升距图 van der waals energy 范德⽡⽿能量 van der waals equation 范德⽡⽿斯⽅程 van der waals force 范德⽡⽿斯⼒ vane 叶⽚ vane grid 叶栅 vane type pump 叶轮泵 vane wheel 叶轮 vaned diffuser 叶⽚式扩散器 vaneless diffuser ⽆叶⽚式扩散器 vanishing 消失 vanishing point 消失点 vapor pressure 蒸汽压 vapor pressure equation 蒸汽压⽅程 vapor pump 蒸汽喷射泵 vaporization 汽化 vaporization heat 蒸发热 vapour 蒸汽 variability 变异性 variable 变数 variable acceleration 可变加速度 variable capacity 可变容量 variable geometry wing 可变翼 variable load 可变负荷 variable mass 变质量 variable mass body 变质量体 variable mass mechanics 变质量⼒学 variable motion 变速运动 variable of state 状态变数 variable pitch airscrew 变距螺旋桨 variable pitch propeller 变距螺旋桨 variable quantity 变量 variable rotation 可变旋转 variable sweep aerofoil 可变后掠翼 variable wind 变向风 variance ⽅差 variation 变化 variation method 变分法 variation of amplitude 幅度的变动 variational calculus 变分学 variational equation 变分⽅程 variational principle 变分原理 variational problem 变分问题 varied orbit 变化轨道 variometer 升降速度仪 vector analysis ⽮量分析 vector component ⽮量分量 vector coupling ⽮量耦合 vector diagram ⽮量图 vector equation ⽮量⽅程 vector field ⽮场 vector flux ⽮通量 vector function ⽮量函数 vector interaction ⽮量相互酌 vector of force ⼒⽮量 vector of oscillation 振荡⽮量 vector polygon ⽮量多边形 vector potential ⽮量势 vector product ⽮积 vector space ⽮量空间 vector sum ⽮量和 vector tube ⽮量管 vector wave equation ⽮量波⽅程 vector wave function ⽮量波函数 vectorial ⽮量的 velocimeter 速度计 velocity 速度 velocity circulation 速度环量 velocity coefficient 速度系数 velocity component 速度分量 velocity constant 速率常数 velocity correlation of turbulence 湍临度相关 velocity coupling 速度耦合 velocity curve 速度曲线 velocity diagram 速度图 velocity distribution 速度分布 velocity distribution function 速度分布函数 velocity ellipse 速度椭圆 velocity field 速度场 velocity gradient 速度梯度 velocity head 速度头 velocity head tachometer 液压转速计 velocity in free space ⾃由空间速度 velocity limit 极限速度 velocity load diagram 速度载荷图 velocity modulation 速度灯 velocity of blade 叶⽚速度 velocity of combustion 燃烧速度 velocity of flow 临 velocity of longitudinal wave 纵波速度 velocity of moving space 牵连速度 velocity of propagation 传播速度 velocity of propagation of flame ⽕焰传播速度 velocity of slip 滑临度 velocity of sound 声速 velocity of transformation 转变速度 velocity of transverse waves 横波速度 velocity of wave front 波前速度 velocity operator 速度算符 velocity parallelogram 速度平⾏四边形 velocity pickup 速度传感器 velocity plane 速度平⾯ velocity potential 速度势 velocity profile 速度剖⾯图 velocity rating 额定速度 velocity resonance 速度共振 velocity shock 速度冲击 velocity space 速度空间 velocity spectrum 速度谱 velocity time diagram 速度时间图 velocity triangle 速度三⾓形 ventilation loss 通风损耗 ventilator 风扇 ventilator pressure 通风机压⼒ venturi meter ⽂丘⾥量计 venturi tube ⽂丘⾥管 vernier 游标 vertex 顶点 vertex function 顶点函数 vertex tangent 顶点切线 vertical 垂直 vertical axis 垂直轴 vertical circle 等⾼圈 vertical component 垂直分量 vertical curve 竖直线 vertical deflection 竖直偏转 vertical displacement 垂直位移 vertical distribution 竖向分布 vertical fall 垂直落下 vertical flow 竖直怜 vertical force 垂直⼒ vertical hydrodynamic force 铃动⼒浮⼒ vertical line 铅垂线 vertical load 垂直荷载 vertical motion 竖向运动 vertical pendulum 竖直摆 vertical plane 垂直⾯ vertical plate 竖直板 vertical projection 垂直投影 vertical reaction 垂直反⼒ vertical section 竖直截⾯ vertical shock 竖震 vertical stream 竖直怜 vertical temperature grade 垂直温度梯度 vertical velocity 竖向速度 vertical velocity curve 竖向临曲线 vertical velocity distribution 竖直速度分布 vertical wind tunnel 竖直风洞 very low frequency 甚低频 vessel 船 vibrate 振动 vibrating compaction 振动压实 vibrating field 振荡场 vibrating load 振动负载 vibrating potential model 振动势模型 vibrating reed 振簧 vibrating rod 振荡棒 vibrating rotator 振动转⼦ vibrating screen 振动筛 vibrating string 振动弦 vibrating system 振动系统 vibrating table 振动台 vibration 振动 vibration absorber 消振器 vibration analysis 振动分析 vibration damper 振动阻尼器 vibration damping 减振 vibration frequency 振动频率 vibration galvanometer 振动式检疗 vibration generator 振动器 vibration instrument 振动仪表 vibration isolation 隔振 vibration isolator 隔振器 vibration level 振动级 vibration meter 振动计 vibration node 振动节点 vibration of bar 杆的振动 vibration of plate 板的振动 vibration of string 弦的振动 vibration pickup 振动传感器 vibration plane 振动平⾯ vibration proof 耐振的 vibration range 振荡范围 vibration resistance 抗振性 vibration resonance 振动共振 vibration rotation 振荡转动 vibration rotation band 振动转动谱带 vibration rotation spectrum 振动转动谱 vibration state 振动态 vibration stress 振动应⼒ vibration system 振动系统 vibration test 振动试验 vibration tester 振动试验仪 vibration testing machine 振动试验仪 vibrational angular momentum 振动⾓动量 vibrational constant 振动常数 vibrational coordinate 振动坐标 vibrational corrosion 振动腐蚀 vibrational energy 振动能 vibrational enthalpy 振动焓 vibrational entropy 振动熵 vibrational instability 振动不稳定性 vibrational line 振动线 vibrational mode 振动模式 vibrational period 振动周期 vibrational perturbation 振动扰动 vibrational relaxation 振动弛豫 vibrational scattering 振动散射 vibrational spectrum 振动谱 vibrational state 振动状态 vibrogram 振动记录图 vibrograph 测振计 vibrometer 振动计 vibroscope 振动仪 vickers hardness 维⽒硬度 virial equation of state 维⾥状态⽅程 virial expansion 维⾥展开 virial theorem 维⾥定理 virtual center 瞬时中⼼ virtual deformation 虚形变 virtual displacement 虚位移 virtual entropy 有效熵 virtual free energy 有效⾃由能 virtual free enthalphy 有效⾃由焓 virtual friction 表观摩擦 virtual inertia 表观惯性 virtual mass 虚质量 virtual particle 虚粒⼦ virtual transformation 虚转变 virtual velocity 假想速度 virtual work 虚功 virtual work method 虚功法 virtual work theorem 虚功定理 visco elasticity 粘弹性 viscoelastic 粘弹性的 viscoelastic body 粘弹性体 viscoelastic foundation 粘弹性基础 viscoelastic gas 粘弹性⽓体 viscoelastic material 粘弹性材料 viscoelastic model 粘弹性模型 viscoelastic solid 粘弹性固体 viscoelastic wave 粘弹性波 viscoelastic wave equation 粘弹性波动⽅程 viscometry 粘度测定法 viscoplastic 粘塑性的 viscoplastic constitutive equation 粘塑性本构⽅程 viscoplastic strain 粘塑性应变 viscoplasticity 粘塑性 viscosimeter 粘度计 viscosimetry 粘度测定法 viscosity 粘性 viscosity correction 粘性校正 viscosity force 粘性⼒ viscosity function 粘度函数 viscosity measurement 粘度测定 viscosity pump 粘性泵 viscosity tensor 粘性张量 viscous boundary layer 粘性边界层 viscous damping 粘性阻尼 viscous drag 粘滞阻⼒ viscous flow 粘性怜 viscous fluid 粘⼒ viscous friction 粘滞摩擦 viscous liquid 粘性液体 viscous motion 粘性怜 viscous resistance 粘滞阻⼒ viscous shearing stress 粘性切应⼒ viscous solid 粘滞固体 viscous strain 粘性应变 viscous stress 粘性应⼒ visibility 能见性 visualization of flow 怜显⽰ void 空隙 void coalescence 孔隙聚结 void coefficient 空隙系数 void fraction 空隙率 volplane 滑翔飞⾏ volume 体积 volume change by shear 切变体积变化 volume compressibility 体积压缩率 volume compression 体积压缩 volume concentration 体积浓度 volume contraction 体积收缩 volume density 体积密度 volume diffusion 体积扩散 volume diffusion coefficient 体积扩散系数 volume elasticity 体积弹性 volume element 体积元 volume energy 体积能 volume expansion coefficient 体积膨胀系数 volume fraction 体积率 volume parameter 体积参数 volume potential 体积势 volume ratio 体积⽐ volume resistance 体积阻⼒ volume resonance 体积共振 volume strain 体积应变 volume stress 体积应⼒ volume velocity 体积速度 volumetric diameter 体积径 volumetric efficiency 体积效率 volumetric energy 体积应变能 volumetric expansion 体积膨胀 volumetric flow rate 体积临 volumetric flowmeter 体积式量计 volumetric flux 体积通量 volumetric force 体积⼒ volumetric modulus of elasticity 体积弹性模量 volumetric strain 体积应变 von karman number 卡门数 vortex 涡旋 vortex center 涡旋中⼼ vortex chamber 涡旋室 vortex core 涡核 vortex field 涡场 vortex filament 涡丝 vortex flow 涡流 vortex flux 涡通量 vortex free motion ⽆涡运动 vortex frequency 涡旋频率 vortex invariant 涡旋不变量 vortex layer 旋涡层 vortex line 涡线 vortex line motion 涡线运动 vortex motion 涡了动 vortex nucleus 涡核 vortex path 涡道 vortex point 涡点 vortex pump 涡旋泵 vortex region 涡柳 vortex ring 涡环 vortex ring flow 涡环怜 vortex sheet 旋涡层 vortex source 涡源 vortex space 涡琳间 vortex street 涡街 vortex strength 涡量度 vortex surface 涡⾯ vortex tube 涡淋 vortex velocity 涡旋速度 vortex wake 涡粒 vorticity 涡量 vorticity density 涡量密度 vorticity tensor 涡度张量 vorticity transfer equation 涡度转移⽅程 vorticity transfer theory 涡度转移理论。
机械设计专业术语的英语翻译1
双滑块机构double-slidermechanism,ellipsograph
双曲柄机构doublecrankmechanism
双曲面齿轮hyperboloidgear
双头螺柱studs
双万向联轴节constant-velocityordoubleuniversaljoint
外齿轮externalgear
弯曲应力beadingstress
弯矩bendingmoment
腕部wrist
往复移动reciprocatingmotion
往复式密封reciprocatingseal
网上设计on-netdesign,OND
微动螺旋机构differentialscrewmechanism
双摇杆机构doublerockermechanism
双转块机构Oldhamcoupling
双列轴承doublerowbearing
双向推力轴承double-directionthrustbearing
松边slack-side
顺时针clockwise
瞬心instantaneouscenter
斜齿轮的当量直齿轮equivalentspurgearofthehelicalgear
心轴spindle
行程速度变化系数coefficientoftravelspeedvariation
行程速比系数advance-toreturn-timeratio
行星齿轮装置planetarytransmission
原始机构originalmechanism
圆形齿轮circulargear
圆柱滚子cylindricalroller
机械设计专业术语英语翻译
机械设计专业术语英语翻译A阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavityB扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ;normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed 变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensationC参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism; Maltesecross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter 齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio 传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft 串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation ; creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse threadD大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment offorce等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment ofinertia等效动力学模型dynamicallyequivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch 端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower 对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gearE额定寿命rating life额定载荷load ratingII 级杆组dyadF发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation 非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone 分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train 复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism 复杂机构complex mechanismG杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing 刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force 惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercuttingH函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm 环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear trainJ积分integrate机电一体化系统设计mechanical-electrical integration system design机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism 机构运动简图kinematic sketch of mechanism 机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery 机械动力设计dynamic design of machinery 机械动力学dynamics of machinery机械的现代设计modern machinedesign机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanicaldesign机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines andmechanisms机械运转不均匀系数coefficient ofspeed fluctuation机械无级变速mechanical steplessspeed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS计算力矩factored moment; calculationmoment计算弯矩calculated bending moment加权系数weighting efficient 加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoids渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line ofinvolute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle ofinvolute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalentradial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating径向基本额定静载荷basic static radial load tating 径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form 锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanismK抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagramL雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel联组V带tight-up V belt联轴器coupling ; shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design ; design for environmentM 马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes 脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion ;wear; scratching末端执行器end-effector目标函数objective functionN耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point 扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramOO形密封圈密封O ring sealP盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏 ( 心 ) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower 偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel keyQ其他常用机构other mechanism in common use 起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact 气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulatorR燃点spontaneous ignition热平衡heat balance; thermal equilibrium 人字齿轮herringbone gear冗余自由度redundant degree of freedom 柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation 润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricantS三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham ‘s coupling矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing 松边slack-side顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不均匀 ( 波动 ) 系数coefficient of speed fluctuation速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocityT塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding motion弹性联轴器elastic coupling ; flexible coupling 弹性套柱销联轴器rubber-cushioned sleeve bearing coupling套筒sleeve梯形螺纹acme thread form特殊运动链special kinematic chain特性characteristics替代机构equivalent mechanism调节modulation, regulation调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing调心轴承self-aligning bearing调速speed governing调速电动机adjustable speed motors调速系统speed control system调压调速variable voltage control调速器regulator, governor 铁磁流体密封ferrofluid seal停车阶段stopping phase停歇dwell同步带synchronous belt同步带传动synchronous belt drive凸的，凸面体convex凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeVV带V beltW外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement位移曲线displacement diagram位姿pose , position and orientation稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices 无穷大infiniteX系杆crank arm, planet carrier现场平衡field balancing向心轴承radial bearing向心力centrifugal force相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear 谐波传动harmonic driving谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism虚拟现实virtual reality虚拟现实技术virtual reality technology,VRT虚拟现实设计virtual reality design,VRD虚约束redundant (or passive)constraint许用不平衡量allowable amount ofunbalance许用压力角allowable pressure angle许用应力allowable stress; permissiblestress悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selectionY压力pressure压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling 雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism一般化运动链generalized kinematicchain移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration 应力图stress diagram应力-应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover 原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel(cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator 圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation 运动粘度kenematic viscosityZ载荷load载荷-变形曲线load-deformation curve载荷-变形图load-deformation diagram窄V带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator 直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane 中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact 周节pitch周期性速度波动periodic speed fluctuation 周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load轴向基本额定动载荷basic dynamic axial load rating轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overallefficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work纵向重合度overlap contact ratio 纵坐标ordinate组合机构combined mechanism 最少齿数minimum teeth number 最小向径 minimum radius作用力 applied force坐标系 coordinate frame。
机械工程学专业词汇英语翻译
acoustic field声场
acoustic filter滤声器
acoustic frequency音频
acoustic impedance声阻抗
acoustic load声负载
acoustic material隔声材料
acoustic mechanical efficiency声机械效率
acoustic power声功率
acoustic pre ure声压
acoustic radiation pre ure声辐射压
acoustic reactance声抗
acoustic resistance声阻
acoustic resonance共鸣
acoustic声的
acoustic a orption声吸收
acoustic a orptio ound a orption声吸收
acoustic a orptivity声吸收率
acoustic admittance声导纳
acoustic analysis声学分析
addition附加
additional drag附加阻力
additional load附加载荷
additional ma 附加质量
additional pre ure附加压力
adhere粘着
adherence附着
adhesion附着
a orption dynamometer吸收功率计
a orption heat吸收热
a orption lo 吸收损失
a orption model吸收模型
a orption potential吸收势
机械专业英语 (2)
机械专业英语1. Introduction机械工程是一门涉及机械设备和工具设计、制造、使用和维护的学科，是工程技术领域中的一个重要分支。
机械专业英语是机械工程学习中必不可少的一部分，它涉及到机械工程师需要掌握的英语词汇、专业术语、文档阅读和撰写技巧等方面。
本文将介绍一些常用的机械专业英语词汇和常用的表达方式，以帮助读者更好地掌握机械专业英语。
2. Mechanical Engineering Vocabulary以下是一些常用的机械工程专业词汇，可以帮助读者对机械工程领域的基本概念有更好的了解：•Mechanical Engineering（机械工程）: A discipline of engineering that deals with the design, construction, and operation of machinery.•Engineer（工程师）: A person who designs, builds, or maintains engines, machines, or public works.•CAD（计算机辅助设计）: Computer-Aided Design, a software tool used by engineers to create and modifymechanical designs.•CAM（计算机辅助制造）: Computer-Aided Manufacturing, a software tool used to controlmanufacturing processes.•CNC（计算机数控）: Computer Numerical Control,a method of controlling manufacturing machines usingcomputers.3. Common Expressions in Mechanical Engineering在机械工程领域，有一些常用的表达方式，以下是一些示例：•According to the design specifications（根据设计规范）: Indicates that something is done in accordance with the design requirements.•The machine is in operation（机器正在运行）: Indicates that the machine is currently running andperforming its intended function.•The material is heat-treated（材料经过热处理）: Indicates that the material has undergone a specific heat treatment process for improved properties.•The system is experiencing mechanical failure（系统发生机械故障）: Indicates that the system is notfunctioning properly due to a mechanical issue.•The component needs to be lubricated regularly（零部件需要定期加润滑油）: Indicates that regularlubrication is required to ensure proper functioning of the component.4. Reading and Writing Documents in Mechanical Engineering在机械工程领域，阅读和撰写文档是非常重要的技能。
机械工程专业英语翻译
机械工程专业英语翻译Introduction机械工程是一门涵盖机械原理、设计、制造以及维护的综合性学科，其中涉及许多专业术语和英语翻译。
良好的英语翻译能力对机械工程师在国际合作和成果交流中至关重要。
本文将介绍机械工程专业中常见的英语单词和短语，并提供中文翻译和相关注释。
Mechanical Principles 机械原理对于机械原理，下面是一些常见的英语单词和短语。
1.Mechanism（机构）：A mechanism is a device designedto transform input forces and movement into a desiredoutput force and movement.2.Kinematics（运动学）：Kinematics is the study ofmotion, without regard to the cause of the motion.3.Statics（静力学）：Statics is the study of thebehavior of structures, under the action of forceswithout producing motion.4.Dynamics（动力学）：Dynamics is the study of thebehavior of motion of objects under the action of forces.5.Thermodynamics（热力学）：Thermodynamics deals withthe relationships between heat, work, and energy.6.Fluid Mechanics（流体力学）：Fluid mechanics is thestudy of the behavior of fluids at rest or in motion. Mechanical Design 机械设计对于机械设计，下面是一些常见的英语单词和短语。
机械工程力学专业英语翻译
4 Overview of Engineering Mechanics（工程力学概况）(1) Ideally, however, every such item has been designed according to some set of “functional requirements” as perceived by the designers-that is, it has been designed so as to answer the question, “E xactly what function should it perform?” In the world of engineering, the major function frequently is to support some type of loading due to weight, inertia, pressure, etc. From the beams in our homes to the wings of an airplane, there must be an appropriate melding of materials, dimensions, and fastenings to produce structures that will perform their functions reliably for a reasonable cost over a reasonable lifetime.然而，在理想的情况下，每一件产品都是设计人员根据对某些“功能要求”的理解而设计出来的，也就是说，在设计过程中，应该回答这样的问题，即“它应该具有哪种确切的功能？”在工程领域，主要功能通常是承受由于重力，惯性力，压力等作用的一些类型的载荷。
从我们居住房屋的梁到飞机机翼，都必须有一个适当的材料，尺寸，在较合理地寿命基础上具有较合理地成本，并能可靠地完成其功能的产品结构连接的组合。
机械类专业词汇中英文对照翻译表大全
机械类专业词汇中英文对照翻译表大全机械类专业词汇表一画一字螺丝批 slot type screwdriver一点透视 one-point perspective二画二合一黏合剂 epoxy resin adhesive二合胶；混合胶 epoxy glue二维的；平面的 two-dimensional二进制 binary二极管；整流子 diode二号螺丝攻 second tap二路开关 two-way switch十进制的；公制的 metric人工制品 artefact人造板 man-made board人体工程学 ergonomics; human engineering人体尺寸 human dimension人体测量学 anthropometry; anthropometrics刀片 blade刀身 blade刀具 tool刀具溜座 carriage刀柱 tool post刀架 tool rest刀架底座 tool rest bracket刀座帷；床鞍 apron刀座鞍；溜板座 saddle力 force力三角形 triangle of force力平行四边形 parallelogram of force 力多边形；多边形力学 polygon of force 力的分解 force resolution力架；亮漆 lacquer力矩 moment力偶 couple力矩定律 law of moment力-距离图表 force-distance graph力图 force diagram力线 line of force力点 effort十字榫 cross halving joint十字螺丝 Philip's head screw十字螺丝批 Philip's type screwdriver 丁字尺；T 尺 tee square三画三爪夹头 three-jaw chuck三角尺 set square三角形结构系杆 triangulation tie三角锉 triangular file三维的；立体的 three-dimensional三氯甲烷；哥罗芳 chloroform三聚氰?胺；蜜胺 melamine三点透视 three-point perspective上油漆 painting上釉 enamelling凡立水 varnish叉形顶尖 fork centre口罩 mask士力；虫漆 shellac士巴拿；扳手 spanner大芯夹板；宽条芯夹板 blockboard; solid corestock-laminated board大量制造 mass production子口刨；槽口刨；边刨 rebate plane小型平槽刨 miniature router plane小型线料弯曲器 small wire bender小型弯折机 mini bender小型电路断路器；跳菲 miniature circuit breaker (MCB)小齿轮 pinion山樟 San Cheong工件 workpiece工字梁 I beam工作面 working surface工作图；制作图 working drawing工作台 bench; working table工具 tool工具贮存室 tool storage工具槽 well工具钢 tool steel工场 workshop工场安全 workshop safety工程字书写技巧 lettering工程系统 engineering system工程绘图 engineering drawing工业酒精；火酒 methylated spirit弓形手钻；手摇曲柄钻 brace弓形手钻嘴 brace bit弓锯 bow saw; hacksaw弓锯片 hacksaw blade弓锯床 hacksawing machine四画不平衡 imbalance不含铁金属；非铁金属 non-ferrous metal不贯穿孔；闭孔；盲孔 blind hole不贯穿鸠尾榫 lapped dovetail joint不对称 asymmetry不锈钢 stainless steel不稳定平衡 unstable equilibrium中心 centre中心线 centre line中心冲 centre punch中心钻 centre drill中心钻嘴 centre bit中央处理器 central processing unit (CPU)中性 neutral中性平衡；随遇平衡 neutral equilibrium中性轴 neutral axis中密度纤维板 medium density fibre board (MDF) 中粗锉纹 second cut中碳钢 medium carbon steel中线 neutral wire互补金属氧化物半导体 complementary metal oxide semiconductors (CMOS)介子；垫片 washer介指铁 ring mandrel介电常数；电容率 permittivity介稳态的；亚稳态的 metastable内力 internal force内卡尺 inside calipers内能 internal energy内涵性质 intensive properties内圆弯凿 scribing gouge内锁式配件 interlocking fitting内燃机 internal combustion engine内螺纹制造法 tapping内螺丝 internal thread内弯边 concave edge六角金属枝 hexagonal bar六角匙 Allen key六角头螺丝 hexagonal head screw公制的；十进制的 metric公差 tolerance冗余构件 redundant member分力 component force分子 molecule分子力 molecular force分切；分割；切断 parting off分贝 decibel分析 analysis分析及批判学 analytical and critical studies 分析器 analyzer分流器 shunt分界面；界面；接口 interface分厘卡 micrometer分规 divider分割车刀架 parting tool holder分解 decomposition分压器 potential divider; voltage divider隔离开关 isolating switch切削工具 cutting tool切削液 cutting fluid切削深度 depth of cut切屑；碎屑 chip切线锯法 tangential sawing切辊纹；滚纹 knurling切断；分切；分割 parting off 切断工具 parting tool勾；勾脚 hook勾刀；胶片?刀 plastic cutter 化胶水 tensol反向偏压 reverse biased反相放大器 inverting amplifier 反相器 inverter反射 reflection反电动势 back e.m.f.反馈；回输 feedback天拿水；稀释剂 thinner天梯牙；齿条 gear rack天然木材 natural timber天然干燥法 air seasoning孔隙率 porosity尺寸 dimension尺寸线 dimension line尺身 blade引力；重力 gravitational force 心形凸轮 heart-shaped cam心材 heartwood心轴 mandrel心销 core pin手工具 hand tool手工锯 junior hacksaw手削法 paring手持虎钳 hand vice手柄 handle手套 gloves手扫漆 brushing lacquer手推车 barrow手提式竖线锯 portable jigsaw手提电动工具 portable power tool 手提电钻 electric hand drill手进给 hand feed手摇曲柄钻；弓形手钻 brace手摇钻 hand drill手锉 hand file手锯；板锯 handsaw手锥 bradawl手辘轧机 hand rolling machine支柱；支撑物 strut支架；支座 support支点 fulcrum; pivot文字 text方向 direction方向针 pointing needle方枝 square bar方波形 square waveform方波产生器 squarer方型牙板 rectangular die方格纸；网格纸 grid paper方通 square tube方块图 block diagram方锉 square file方头钻嘴 square shank bit方螺帽 square nut方边凿；直边凿 firmer chisel木 wood木工 woodwork木工工作间 woodwork area木工工作台 woodworker's bench木工车床 wood turning lathe; woodworking lathe木工铅笔 carpenter's pencil木工刨床 thicknessing and planning machine木牙螺丝；木螺钉 wood screw木材 timber木材车削 wood turning木材车削工具 wood turning tools木屑压合板；万花板 chipboard木条接榫 corner strip joint木圆头槌 doming mallet木模；模型 patterns木线 wood strip木胶粉 ureaformal dehyde resin glue木锉 rasp木螺钉；木牙螺丝 wood screw木槌 mallet止推轴承 thrust bearing止推垫圈 thrust washer比例 proportion比例尺 scale比例常数 proportionality constant比例极限 proportional limit比较器 comparator比热容量 specific heat capacity水平投影面 horizontal plane水平仪；平水尺 spirit level水气掣；漏电断路掣 earth leakage circuit breaker (ELCB) 水晶胶；聚酯树脂 polyester resin水晶胶的铸造成形 resin casting水磨砂纸 silicon carbide paper火叉 firing fork火水；煤油 kerosene火牛；变压器 transformer火石轮 grinder火花电蚀法；放电极加工 electrical discharge machining火酒；工业酒精 methylated spirit火钳 tongs火线；活线 live wire火砖 fire brick爪扣；爪形离合器；犬齿式离合器 dog clutch牙板；丝模 die牙板扳手；丝模扳手 die holder (stock)牙板螺帽 die nuts牛皮胶；动物胶 animal glue牛油纸 tracing paper牛顿运动定律 Newton's laws of motion犬齿式离合器；爪扣；爪形离合器 dog clutch五画丙烯?丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS) 主轴；心轴 spindle主题 motif令(纸张的计数单位) ream凹座 recess凹模 hollowing block凸缘 flange凸缘联轴节 flange coupling凸轮 cam凸轮式配件 cam-action fitting凸轮传动 cam drive凸头螺丝 raised head screw加成作业；添加法 addition process加油 oiling加速器 accelerator功能；用途 function功率因子 power factor功率放大器 power amplifier功率板 power amplifier board功率晶体管 power transistor包氏记号法 Bow's notation「包浩思」；「包豪斯」〈设计风格) Bauhaus半永固法；半永久接合 semi-permanent joining 半接榫 halving joint半闭式槽榫 stopped housing joint半圆(木)锉 half-round rasp半圆车刀 turning gouge半圆锉 half-round file半圆头铆钉 snap rivet半导体 semiconductor卡路里；卡(热量单位) calorie卡纸 card paper卡尺；测径器 calipers去角；倒角 chamfer可切削性 machinability可行性 feasibility可逆过程 reversible process可压缩性 compressibility可变电阻 variable resistor四分仪 quadrant四爪夹头 four-jaw independent chuck四圆心法(绘图) four-centre method外卡尺 outside calipers外形塑造 shaping外形线；轮廓线 outline外推法 extrapolation外圆弯凿 firmer gouge外螺纹 external thread外螺纹制造法 threading外弯边 convex edge外观 appearance失真 distortion尼龙；聚醯胺 nylon; polyamide (PA)尼龙墨水针笔 technical felt-tip pen左右调校杆 lateral adjusting level市售尺寸；标准尺寸 stock size市电频率；电源频率 mains frequency平(木)锉 flat rasp平水尺；水平仪 spirit level平行投影 parallel projection平行车削 parallel turning平行虎钳 parallel vice平行钉法 parallel nailing平底弯刨 flat faced spokeshave平底钻嘴 forstner bit平板结构 slab construction平流扼流圈；滤波扼流器 smoothing choke平流电容器；滤波电容器 smoothing capacitor 平流电路；滤汳电路 smoothing circuit平面板；正台 surface plate平面图；俯视图 plan平面锤 flatter平移 translation平搭榫 corner halving joint平嘴钳 flat nose pliers平槽刨 router plane平衡 balance; equilibrium平衡力 equilibrant平衡条件 equilibrium condition平衡电桥 balanced bridge平头弧刀 square nose gouge幼纹 smooth cut打凹成形 hollowing打凸成形 raising打槽机 routing machine打线；打槽 routing打磨 fitting; polishing打磨机 polisher本生灯 Bunsen burner本征半导体 intrinsic semiconductor 正反器；触发器；复振器 flip-flop 正反馈；正回输 positive feedback 正火 normalizing正向偏置 forward bias正投影 orthographic projection正投影图 orthographic drawing正弦波形 sinusoidal waveform正面投影 front projection正视图 elevation; front elevation 正极；阳极 anode正齿轮 spur gear正台；平面板 surface plate永久性接合 permanent joining瓦通纸；瓦楞纸板 corrugated board生长层 cambium layer生产图 production drawing生胶浆 rubber cement生钢；铸钢 cast steel生铁；铸铁 cast iron用途；功能 function白杨木 poplar白胶浆 PVA glue; white glue皮沙垫 leather sandbag皮革 leather皮革黏合剂 leather glue皮鞋 leather shoes目录 contents矢量；向量 vector石灰岩 limestone石英晶体振荡器 quartz crystal oscillator石棉 asbestos; asbestus石膏 Plaster of Paris示波器 oscilloscope立体图 pictorial drawing六画交流电流 alternating current (a.c.)交流电压 a.c. voltage交联结构 cross-linked structure仿饰金 gilding metal伏特 volt光力架 clear lacquer光拉软钢 bright drawn mild steel (B.D.M.S.) 光敏电阻 light dependent resistor (LDR)光测弹性学 photoelasticity光刨；滑刨 smoothing plane光电效应 photoelectric effect光泽 lustre全闭式槽榫 closed housing joint共面力 coplanar force共聚合作用 co-polymerization共聚物 copolymer共价键 covalent bond共振；共鸣；谐振 resonance印刷电路板 printed circuit board (PCB)同素异形 allotropy同轴电缆 coaxial cable同温 equality of temperature向量；矢量 vector向量和 vector sum104合力 resultant force合口扁钳 close mouth tongs合成色；等和色 secondary colour合成品 composite合成粅料 composite material合金 alloy合金工具钢 alloy tool steel合钉；定位销 dowel回火 tempering回复力 restoring force回复力偶 restoring couple回弹 resilience回输；反馈 feedback地线 earth wire多刃切削刀具 multi-point cutter多孔塑料；泡沫塑料；海绵状塑料 foam plastics多方榫接合 pinned joint多媒体 multi-media多晶性 polycrystallinity多谐振动器；多谐振荡器 multivibrator 多边形力学；力多边形 polygon of force 字母冲 letter punch字板 letter stencil安全 safety安全守则 safety rule安全系数 safety factor安全措施 safety precaution105安全眼罩 safety goggle安全设备 safety equipment安全药箱 safety box安培 ampere安培计；电流表 ammeter尖脚 spur年轮 annual ring成本 cost成形 forming扣件；击固件 fastener扣钉 clout nail; cramp托架 bracket收缩 shrinkage曲柄 crank曲柄轴 crank shaft曲线规；云板；云尺 French curve有效的 efficient有效电流 effective current灰；灰末 ash百折胶；百折胶；聚丙烯 polypropylene (PP) 竹 bamboo羊角锤 claw hammer老化 ageing肋条 rib肌理；质感；质地 texture自由度 degree of freedom自动控制 automatic control106自动进给 auto-feed自然干燥法 natural seasoning自感量 self-inductance自感应 self-induction色彩；颜色 colour色调 tone色环 colour wheel行星齿轮；周转齿轮 epicyclic gear七画肘节开关 toggle-switch串激电动机；串绕电动机 series-wound motor 位能；势能 potential energy位梯度；势梯度 potential gradient位移 displacement位错 dislocation伸长度 elongation作工硬化 work hardening作功 work done作图线 construction line低密聚乙烯 low density polyethylene (LDPE) 低通滤波器 low-pass filter低电压 low voltage低碳钢 low carbon steel布置 layout免油轴承 oil-less bearing冷加工；冷作工 cold working冷加工硬化 cold work hardening冷色 cool colour冷轧压 cold rolling冷却系统 cooling system冷却效应 cooling effect冷却液流量 coolant rate冷凝胶；环氧树脂 epoxy resin108利口；「披」口；铁屑 burr刨平 planing刨花板；碎料板 particle board吹风机 air blower吹气模塑；吹模塑 blow moulding吹管 blow pipe含铁金属 ferrous metal含水量 moisture content坑凿 cross-cut chisel均方根值 root mean square value均角投影图；等角投影图 isometric drawing 均速圆周运动 uniform circular motion 夹；夹钳 clamp夹 cramp夹卡 mounting board夹具 fixture; jig夹具及固定装置 jig and fixture夹板；胶合板 plywood夹持工具 clamping device; holding tool夹背锯；榫锯 tenon saw夹头 chuck夹头开启匙；夹头扳手 chuck key夹叠黏合成形 lamination尾座 tailstock床身；床道 lathe bed床鞍；刀座帷 apron形心；面心 centroid109形状 shape形变 deformation「快把」板；硬质纤维板 hardboard快速移位 rapid traverse抗扭强度 torsional strength抗屈强度 bending strength; yield strength 抗性分量；无功分量 reactive component抗拉强度 tensile strength抗氧化剂 anti-oxidant抗剪强度 shearing strength抗磁性物料 diamagnetic material抗挠性 stiffness抗压强度 compressive strength抗断强度 breaking strength技术员；技师 technician扶架 steady扭力 torsion扭矩；转矩 torque扭转 torsion扭转角 angle of torsion把手 hand grip扼流圈 choke扳手 spanner; wrench投影 projection投影面 projection plane投影线 projection line攻丝 tap材料 material材料单；材料表 material list杜拉铝 duralumin杉木 spruce步进电动机 stepper motor步冲轮廓法 nibbling每分钟转数 revolution per minute (r.p.m.) 系统组件 system component角托架 angle bracket角位移 angular displacement角板；直角板 angle plate角度 angle角榫 corner angle joint; corner joint角铁 angle iron谷巴凡立水 cobal varnish车刀架 tool holder车床 lathe车床工具 lathe tools车床中心钻咀 lathe centre bit车床操作法 lathe operation车削；车旋 lathe turning; turning车削工具 turning tools防火胶板 Formica防锈 rust prevention防声耳筒；护耳器 ear-protector防松螺帽 lock nut防护装置；保护罩；保护网 guard; safety guard八画注射成形法；喷射铸造法 injection moulding并激电动机；并绕电动机 shunt-wound motor乳酪胶 casein glue乳胶漆 emulsion paint亚加力；压克力；聚甲基丙烯酸甲脂 acrylics; polymethyl methacrylate (PMMA)亚稳态的；介稳态的 metastable来回摆动 oscillating两点透视 two-point perspective刻度；划线 ruling刺冲 dot punch刮刀 scraper刮擦 scraping制动鼓 drum brake制动碟 disc brake制动器 brake受迫振动 forced vibration受迫振荡 forced oscillation和谐 harmony周转齿轮；行星齿轮 epicyclic gear固定夹；台夹 bench holdfast固定负载 dead load定子 stator定位销；合钉 dowel定位螺丝 set screw定距轮 stitch marker屈片机 folding machine屈曲 bending屈服点；降服点 yield point屈圈法 loop forming屈卷法 scrolling屈接缝 folded lap seam屈喉机 tube bender屈折 folding屈折线 folding line屈压接缝 folded & grooved seam延性 ductility延性的 ductile弦锯法 plain sawing弧口凿；圆凿 gouge往复式运动 reciprocatory motion拉力 tensile force拉力计；张力计 tensiometer; tensometer拉钉 blind rivet; pop rivet拉钉接合 blind riveting; pop riveting拉钉钳 blind riveting pliers; pop riveting pliers 拉张 tension拉张应力 tensile stress拉张应变 tensile strain拉细 drawing-down拉制法 drawing拉线 wire drawing「披」口；利口；铁屑 burr拔钳 nippers拋光 buffing拋光机 buffing machine放大；扩大 enlargement放大尺 pantograph放大倍数 amplification factor放大器 amplifier放电极加工；火花电蚀法 electrical discharge machining 易用万能尺 line setter易碎 fragile〈绘画的〉明暗运用；描影 shading枝；杆 rod杯形顶尖 cup centre杯头螺丝 hexagonal socket head cap screw板锯 panel saw松木 pine松节水 turpentine法式磨光 French polishing法拉〈电容量单位〉 farad油石；磨刀石 oil stone油漆；涂料 paint泡沫塑料；多孔塑料；海绵状塑料 foam plastics物理特性 physical property物理属性 physical attribute物理量 physical quantity盲孔；闭孔；不贯穿孔 blind hole直尺 ruler; straight rule直角叉榫 corner bridle joint直角尺 try square直角板；角板 angle plate直角杠杆 bell crank lever直身钻嘴 straight shank drill直车刀架 straight tool holder直流发电机 d.c. generator直流电流 direct current (d.c.)直流电动机；直流马达 d.c. motor直纹锯 rip saw直线切削 linear interpolation直线运动 rectilinear motion直边凿；方边凿 firmer chisel直铁剪 straight snips硅 silicon空行程 idle stroke空气动力学 aerodynamics空间 space空载 no load花纹凿 embossing stamp花梨木 rosewood花样；图案 pattern虎克定律 Hooke's Law虎钳 vice虎钳护罩 vice clamp初步意念 proposed solution表面 surface表面展开图 surface development表面张力 surface tension表面处理 surface finishing; surface treatment 表面硬化 case hardening表面硬化钢 case-hardened steel表达方式 presentation表达技巧；传意技巧 communication technique表观膨胀；视膨胀 apparent expansion金工 metalwork金工工作间 metalwork area金工角尺 engineering square金工车床 metalwork lathe金工虎钳 engineer's vice金工锯床 power hacksaw金属包头；金属箍 ferrule金属配件 metal fittings金属线 wire金属压展机 hand rolling mill金属擦光剂；磨光剂 metal polish金属薄片 sheet metal金属键 metallic bond长方通 rectangular tube长刨 trying plane长螺旋钻咀 long auger bit长镗孔 long boring闸极 gate阻抗 impedance附件 attachment附录 appendices青铜 bronze非反相放大器 non-inverting amplifier非本征半导体 extrinsic semiconductor非破坏性试验 non-destructive testing非晶状固体 amorphous solid非顽磁性铁磁材料 non-retentive ferromagnetic material 非压缩性流体 incompressible fluid非稳态 unsteady state非铁金属；不含铁金属 non-ferrous metal九画亮漆；力架 lacquer信号 signal信号产生机 signal generator信号处理 signal processing保养；维修 maintenance保险丝 fuse保护罩；保护网；防护装置 guard; safety guard促凝剂 accelerator削屑 swarf垂直投影面 vertical plane型砧 swages〈书的〉封皮 binding封面 cover急回机构 quick return mechanism 扁枝 bar扁头 cross-pein扁头法 upsetting扁头铆钉 flat head rivet扁头螺丝 flat head screw扁凿 flat chisel指示器 indicator指形榫 finger joint施力 effort染色 staining染色剂 stain架构 framework柄 stock柚木 teak柳安木 lauan。
大学各个专业名称的英文翻译
中文学科、专业名称英文学科、专业名称哲学 Philosophy哲学 Philosophy马克思主义哲学 Philosophy of Marxism中国哲学 Chinese Philosophy外国哲学 Foreign Philosophies逻辑学 Logic伦理学 Ethics美学 Aesthetics宗教学 Science of Religion科学技术哲学 Philosophy of Science and Technology经济学 Economics理论经济学 Theoretical Economics政治经济学 Political Economy经济思想史 History of Economic Thought经济史 History of Economic西方经济学 Western Economics世界经济 World Economics人口、资源与环境经济学 Population, Resources and Environmental Economics应用经济学 Applied Economics国民经济学 National Economics区域经济学 Regional Economics财政学（含税收学） Public Finance (including Taxation)金融学（含保险学） Finance (including Insurance)产业经济学 Industrial Economics国际贸易学 International Trade劳动经济学 Labor Economics统计学 Statistics数量经济学 Quantitative Economics中文学科、专业名称英文学科、专业名称国防经济学 National Defense Economics法学 Law法学 Science of Law法学理论 Jurisprudence法律史 Legal History宪法学与行政法学 Constitutional Law and Administrative Law刑法学 Criminal Jurisprudence民商法学(含劳动法学、社会保障法学) Civil Law and Commercial Law (including Science of Labour Law and Science of Social Security Law )诉讼法学 Science of Procedure Laws经济法学 Science of Economic Law环境与资源保护法学 Science of Environment and Natural Resources Protection Law 国际法学(含国际公法学、国际私法学、国际经济法学、) International law (including International Public law, International Private Law and International Economic Law)军事法学 Science of Military Law政治学 Political Science政治学理论 Political Theory中外政治制度 Chinese and Foreign Political Institution科学社会主义与国际共产主义运动 Scientific Socialism and International Communist Movement中*史(含党的学说与党的建设) History of the Communist Party of China(including the Doctrine of China Party and Party Building)马克思主义理论与思想政治教育 Education of Marxist Theory and Education in Ideology and Politics国际政治学 International Politics国际关系学 International Relations外交学 Diplomacy社会学 Sociology社会学 Sociology人口学 Demography人类学 Anthropology民俗学(含中国民间文学) Folklore (including Chinese Folk Literature)民族学 Ethnology民族学 Ethnology马克思主义民族理论与政策 Marxist Ethnic Theory and Policy中国少数民族经济 Chinese Ethnic Economics中国少数民族史 Chinese Ethnic History中国少数民族艺术 Chinese Ethnic Art教育学 Education教育学 Education Science教育学原理 Educational Principle课程与教学论 Curriculum and Teaching Methodology教育史 History of Education比较教育学 Comparative Education学前教育学 Pre-school Education高等教育学 Higher Education成人教育学 Adult Education职业技术教育学 Vocational and Technical Education特殊教育学 Special Education教育技术学 Education Technology心理学 Psychology基础心理学 Basic Psychology发展与心理学 Developmental and Educational Psychology应用心理学 Applied Psychology体育学 Science of Physical Culture and Sports体育人文社会学 Humane and Sociological Science of Sports运动人体科学 Human Movement Science体育教育训练学 Theory of Sports Pedagogy and Training民族传统体育学 Science of Ethnic Traditional Sports文学 Literature中国语言文学 Chinese Literature文艺学 Theory of Literature and Art语言学及应用语言学 Linguistics and Applied Linguistics汉语言文字学 Chinese Philology中国古典文献学 Study of Chinese Classical Text中国古代文学 Ancient Chinese Literature中国现当代文学 Modern and Contemporary Chinese Literature中国少数民族语言文学 Chinese Ethnic Language andLiterature比较文学与世界文学 Comparative Literature and World Literature外国语言文学 Foreign Languages and Literatures英语语言文学 English Language and Literature俄语语言文学 Russian Language and Literature法语语言文学 French Language and Literature德语语言文学 German Language and Literature日语语言文学 Japanese Language and Literature印度语言文学 Indian Language and Literature西班牙语语言文学 Spanish Language and Literature阿拉伯语语言文学 Arabic Language and Literature欧洲语言文学 European Language and Literature亚非语言文学 Asian-African Language and Literature外国语言学及应用语言学 Linguistics and Applied Linguistics inForeign Languages新闻传播学 Journalism and Communication新闻学 Journalism传播学 Communication艺术学 Art艺术学 Art Theory音乐学 Music美术学 Fine Arts设计艺术学 Artistic Design戏剧戏曲学 Theater and Chinese Traditional Opera电影学 Film广播电视艺术学 Radio and television Art舞蹈学 Dance历史学 History历史学 History史学理论及史学史 Historical Theories and History of Historical Science考古学及博物馆学 Archaeology and Museology历史地理学 Historical Geography历史文献学(含敦煌学、古文字学) Studies of Historical Literature (including Paleography and Studies of Dunhuang)专门史 History of Particular Subjects中国古代史 Ancient Chinese History中国近现代史 Modern and Contemporary Chinese History世界史 World History理学 Natural Science数学 Mathematics基础数学 Fundamental Mathematics计算数学 Computational Mathematics概率论与数理统计 Probability and Mathematical Statistics应用数学 Applied mathematics运筹学与控制论 Operational Research and Cybernetics物理学 Physics理论物理 Theoretical Physics粒子物理与原子核物理 Particle Physics and Nuclear Physics原子与分子物理 Atomic and Molecular Physics等离子体物理 Plasma Physics凝聚态物理 Condensed Matter Physics声学 Acoustics光学 Optics无线电物理 Radio Physics化学 Chemistry无机化学 Inorganic Chemistry分析化学 Analytical Chemistry有机化学 Organic Chemistry物理化学（含化学物理） Physical Chemistry (including Chemical Physics) 高分子化学与物理 Chemistry and Physics of Polymers天文学 Astronomy天体物理 Astrophysics天体测量与天体力学 Astrometry and Celestial Mechanics地理学 Geography自然地理学 Physical Geography人文地理学 Human Geography地图学与地理信息系统 Cartography and Geography Information System大气科学 Atmospheric Sciences气象学 Meteorology大气物理学与大气环境 Atmospheric Physics and Atmospheric Environment 海洋科学 Marine Sciences物理海洋学 Physical Oceanography海洋化学 Marine Chemistry海洋生理学 Marine Biology海洋地质学 Marine Geology地球物理学 Geophysics固体地球物理学 Solid Earth Physics空间物理学 Space Physics地质学 Geology矿物学、岩石学、矿床学 Mineralogy, Petrology, Mineral Deposit Geology 地球化学 Geochemistry古生物学与地层学（含古人类学） Paleontology and Stratigraphy (including Paleoanthropology)构造地质学 Structural Geology第四纪地质学 Quaternary Geology生物学 Biology植物学 Botany动物学 Zoology生理学 Physiology水生生物学 Hydrobiology微生物学 Microbiology神经生物学 Neurobiology遗传学 Genetics发育生物学 Developmental Biology细胞生物学 Cell Biology生物化学与分子生物学 Biochemistry and Molecular Biology生物物理学 Biophysics生态学 Ecology系统科学 Systems Science系统理论 Systems Theory系统分析与集成 Systems Analysis and Integration科学技术史 History of Science and Technology工学 Engineering力学 Mechanics一般力学与力学基础 General and Fundamental Mechanics固体力学 Solid Mechanics流体力学 Fluid Mechanics工程力学 Engineering Mechanics机械工程 Mechanical Engineering机械制造及其自动化 Mechanical Manufacture and Automation机械电子工程 Mechatronic Engineering机械设计与理论 Mechanical Design and Theory车辆工程 Vehicle Engineering光学工程 Optical Engineering仪器科学与技术 Instrument Science and Technology精密仪器及机械 Precision Instrument and Machinery测试计量技术及仪器 Measuring and Testing Technologies and Instruments 材料科学与工程 Materials Science and Engineering材料物理与化学 Materials Physics and Chemistry材料学 Materialogy材料加工工程 Materials Processing Engineering冶金工程 Metallurgical Engineering冶金物理化学 Physical Chemistry of Metallurgy钢铁冶金 Ferrous Metallurgy有色金属冶金 Non-ferrous Metallurgy动力工程及工程热物理 Power Engineering and Engineering Thermophysics工程热物理 Engineering Thermophysics热能工程 Thermal Power Engineering动力机械及工程 Power Machinery and Engineering流体机械及工程 Fluid Machinery and Engineering制冷及低温工程 Refrigeration and Cryogenic Engineering化工过程机械 Chemical Process Equipment电气工程 Electrical Engineering电机与电器 Electric Machines and Electric Apparatus电力系统及其自动化 Power System and its Automation高电压与绝缘技术 High Voltage and Insulation Technology电力电子与电力传动 Power Electronics and Power Drives电工理论与新技术 Theory and New Technology of Electrical Engineering电子科学与技术 Electronics Science and Technology物理电子学 Physical Electronics电路与系统 Circuits and Systems微电子学与固体电子学 Microelectronics and Solid State Electronics电磁场与微波技术 Electromagnetic Field and Microwave Technology信息与通信工程 Information and Communication Engineering通信与信息系统 Communication and Information Systems信号与信息处理 Signal and Information Processing控制科学与工程 Control Science and Engineering控制理论与控制工程 Control Theory and Control Engineering检测技术与自动化装置 Detection Technology and Automatic Equipment系统工程 Systems Engineering模式识别与智能系统 Pattern Recognition and Intelligent Systems导航、制导与控制 Navigation, Guidance and Control计算机科学与技术 Computer Science and Technology计算机软件与理论 Computer Software and Theory计算机系统结构 Computer Systems Organization计算机应用技术 Computer Applied Technology建筑学 Architecture建筑历史与理论 Architectural History and Theory建筑设计及其理论 Architectural Design and Theory城市规划与设计（含风景园林规划与设计） Urban Planning and Design (including Landscape Planning and Design)建筑技术科学 Building Technology Science土木工程 Civil Engineering岩土工程 Geotechnical Engineering结构工程 Structural Engineering市政工程 Municipal Engineering供热、供燃气、通风及空调工程 Heating, Gas Supply, Ventilating and Air Conditioning Engineering防灾减灾工程及防护工程 Disaster Prevention and Reduction Engineering and Protective Engineering桥梁与隧道工程 Bridge and Tunnel Engineering水利工程 Hydraulic Engineering水文学及水资源 Hydrology and Water Resources水力学及河流动力学 Hydraulics and River Dynamics水工结构工程 Hydraulic Structure Engineering水利水电工程 Hydraulic and Hydro-Power Engineering港口、海岸及近海工程 Harbor, Coastal and Offshore Engineering测绘科学与技术 Surveying and Mapping大地测量学与测量工程 Geodesy and Survey Engineering摄影测量与遥感 Photogrammetry and Remote Sensing地图制图学与地理信息工程 Cartography and Geographic Information Engineering化学工程与技术 Chemical Engineering and Technology化学工程 Chemical Engineering化学工艺 Chemical Technology生物化工 Biochemical Engineering应用化学 Applied Chemistry工业催化 Industrial Catalysis地质资源与地质工程 Geological Resources and Geological Engineering矿产普查与勘探 Mineral Resource Prospecting and Exploration地球探测与信息技术 Geodetection and Information Technology地质工程 Geological Engineering矿业工程 Mineral Engineering采矿工程 Mining Engineering矿物加工工程 Mineral Processing Engineering安全技术及工程 Safety Technology and Engineering石油与天然气工程 Oil and Natural Gas Engineering油气井工程 Oil-Gas Well Engineering油气田开发工程 Oil-Gas Field Development Engineering油气储运工程 Oil-Gas Storage and Transportation Engineering纺织科学与工程 Textile Science and Engineering纺织工程 Textile Engineering纺织材料与纺织品设计 Textile Material and Textiles Design纺织化学与染整工程 Textile Chemistry and Dyeing and Finishing Engineering服装设计与工程 Clothing Design and Engineering轻工技术与工程 The Light Industry Technology and Engineering制浆造纸工程 Pulp and Paper Engineering制糖工程 Sugar Engineering发酵工程 Fermentation Engineering皮革化学与工程 Leather Chemistry and Engineering交通运输工程 Communication and Transportation Engineering道路与铁道工程 Highway and Railway Engineering交通信息工程及控制 Traffic Information Engineering & Control交通运输规划与管理 Transportation Planning and Management载运工具运用工程 Vehicle Operation Engineering船舶与海洋工程 Naval Architecture and Ocean Engineering船舶与海洋结构物设计制造 Design and Construction of Naval Architecture and Ocean Structure轮机工程 Marine Engine Engineering水声工程 Underwater Acoustics Engineering航空宇航科学与技术 Aeronautical and Astronautical Science and Technology飞行器设计 Flight Vehicle Design航空宇航推进理论与工程 Aerospace Propulsion Theory and Engineering航空宇航器制造工程 Manufacturing Engineering of Aerospace Vehicle人机与环境工程 Man-Machine and Environmental Engineering兵器科学与技术 Armament Science and Technology武器系统与运用工程 Weapon Systems and Utilization Engineering兵器发射理论与技术 Armament Launch Theory and Technology火炮、自动武器与弹药工程 Artillery, Automatic Gun and Ammunition Engineering军事化学与烟火技术 Military Chemistry and Pyrotechnics核科学与技术 Nuclear Science and Technology核能科学与工程 Nuclear Energy Science and Engineering核燃料循环与材料 Nuclear Fuel Cycle and Materials核技术及应用 Nuclear Technology and Applications辐射防护及环境保护 Radiation and Environmental Protection农业工程 Agricultural Engineering农业机械化工程 Agricultural Mechanization Engineering农业水土工程 Agricultural Water-Soil Engineering农业生物环境与能源工程Agricultural Biological Environmental and Energy Engineering农业电气化与自动化 Agricultural Electrification and Automation林业工程 Forestry Engineering森林工程 Forest Engineering木材科学与技术 Wood Science and Technology林产化学加工工程 Chemical Processing Engineering of Forest Products环境科学与工程 Environmental Science and Engineering环境科学 Environmental Science环境工程 Environmental Engineering生物医学工程 Biomedical Engineering食品科学与工程 Food Science and Engineering食品科学 Food Science粮食、油脂及植物蛋白工程 Cereals, Oils and Vegetable Protein Engineering农产品加工及贮藏工程 Processing and Storage of Agriculture Products水产品加工及贮藏工程 Processing and Storage of Aquatic Products农学 Agriculture作物学 Crop Science作物栽培学与耕作学 Crop Cultivation and Farming System作物遗传育种学 Crop Genetics and Breeding园艺学 Horticulture果树学 Pomology蔬菜学 Olericulture茶学 Tea Science农业资源利用学 Utilization Science of Agricultural Resources土壤学 Soil Science植物营养学 Plant Nutrition植物保护学 Plant Protection植物病理学 Plant Pathology农业昆虫与害虫防治 Agricultural Entomology and Pest Control农药学 Pesticide Science畜牧学 Animal Science动物遗传育种与繁殖 Animal Genetics, Breeding and ReproductionScience动物营养与饲料科学 Animal Nutrition and Feed Science草业科学 Practaculture Science特种经济动物饲养学（含蚕、蜂等） The Rearing of Special-type EconomicAnimals (including Silkworm, Honeybees, etc.)兽医学 Veterinary Medicine基础兽医学 Basic Veterinary Medicine预防兽医学 Preventive Veterinary Medicine临床兽医学 Clinical Veterinary Medicine林学 Forestry林木遗传育种学 Forest Tree Genetics and Breeding森林培育学 Silviculture森林保护学 Forest Protection森林经理学 Forest Management野生动植物保护与利用 Wildlife Conservation and Utilization园林植物与观赏园艺 Ornamental Plants and Horticulture水土保持与荒漠化防治 Soil and Water Conservation and Desertification Combating 水产学 Fisheries Science水产养殖学 Aquaculture Science捕捞学 Fishing Science渔业资源学 Science of Fisheries Resources医学 Medicine基础医学 Basic Medicine人体解剖与组织胚胎学 Human Anatomy, Histology and Embryology免疫学 Immunology病原生物学 Pathogenic Organisms病理学与病理生理学 Pathology and Pathophysiology法医学 Forensic Medicine放射医学 Radiation Medicine航空航天与航海医学 Aerospace and Nautical medicine临床医学 Clinical Medicine内科学（含心血管病学、血液病学、呼吸系病学、消化系病学、内分泌与代谢病学、肾脏病学、风湿病学、传染病学） Internal medicine (including Cardiology, Hematology, Respiratory, Gastroenterology, Endocrinology and Metabolism, Nephrology, Rheuma-tology, Infectious Diseases)儿科学 Pediatrics老年医学 Geriatrics神经病学 Neurology精神病与精神卫生学 Psychiatry and Mental Health皮肤病与性病学 Dermatology and Venereology影像医学与核医学 Imaging and Nuclear Medicine临床检验诊断学 Clinical Laboratory Diagnostics护理学 Nursing外科学（含普通外科学、骨外科学、泌尿外科学、胸心血管外科学、神经外科学、整形外科学、烧伤外科学、野战外科学） Surgery (General Surgery, Orthopedics, Urology, Cardiothoracic Surgery, Neurosurgery, Plastic Surgery, Burn Surgery, Field Surgery) 妇产科学 Obstetrics and Gynecology眼科学 Ophthalmic Specialty耳鼻咽喉科学 Otolaryngology肿瘤学 Oncology康复医学与理疗学 Rehabilitation Medicine & Physical Therapy运动医学 Sports Medicine麻醉学 Anesthesiology急诊医学 Emergency Medicine口腔医学 Stomatology口腔基础医学 Basic Science of Stomatology口腔临床医学 Clinical Science of Stomatology公共卫生与预防医学 Public Health and Preventive Medicine流行病与卫生统计学 Epidemiology and Health Statistics劳动卫生与环境卫生学 Occupational and Environmental Health营养与食品卫生学 Nutrition and Food Hygiene儿少卫生与妇幼保健学 Maternal, Child and Adolescent Health卫生毒理学 Hygiene Toxicology军事预防医学 Military Preventive Medicine中医学 Chinese Medicine中医基础理论 Basic Theories of Chinese Medicine中医临床基础 Clinical Foundation of Chinese Medicine中医医史文献 History and Literature of Chinese Medicine方剂学 Formulas of Chinese Medicine中医诊断学 Diagnostics of Chinese Medicine中医内科学 Chinese Internal Medicine中医外科学 Surgery of Chinese Medicine中医骨伤科学 Orthopedics of Chinese Medicine中医妇科学 Gynecology of Chinese Medicine中医儿科学 Pediatrics of Chinese Medicine中医五官科学 Ophthalmology and Otolaryngoloy of Chinese Medicine针灸推拿学 Acupuncture and Moxibustion and Tuina of Chinese medicine民族医学 Ethnomedicine中西医结合医学 Chinese and Western Integrative Medicine中西医结合基础医学 Basic Discipline of Chinese and Western Integrative中西医结合临床医学 Clinical Discipline of Chinese and Western Integrative Medicine 药学 Pharmaceutical Science药物化学 Medicinal Chemistry药剂学 Pharmaceutics生药学 Pharmacognosy药物分析学 Pharmaceutical Analysis微生物与生化药学 Microbial and Biochemical Pharmacy药理学 Pharmacology中药学 Science of Chinese Pharmacology军事学 Military Science军事思想学及军事历史学 Military Thought and Military History军事思想学 Military Thought军事历史学 Military History战略学 Science of Strategy军事战略学 Military Strategy战争动员学 War Mobilization战役学 Science of Operations联合战役学 Joint Operation军种战役学（含第二炮兵战役学） Armed Service Operation (including Operation of Strategic Missile Force)战术学 Science of Tactics合同战术学 Combined-Arms Tactics兵种战术学 Branch Tactics军队指挥学 Science of Command作战指挥学 Combat Command军事运筹学 Military Operation Research军事通信学 Military Communication军事情报学 Military Intelligence密码学 Cryptography军事教育训练学（含军事体育学） Military Education and Training (including Military Physical Training)军制学 Science of Military System军事组织编制学 Military Organizational System军队管理学 Military Management军队政治工作学 Science of Military Political Work军事后勤学与军事装备学 Science of Military Logistics and Military Equipment军事后勤学 Military Logistics后方专业勤务 Rear Special Service军事装备学 Military Equipment管理学 Management Science管理科学与工程 Management Science and Engineering工商管理学 Science of Business Administration会计学 Accounting企业管理学（含财务管理、市场营销学、人力资源管理学） Corporate Management (including Financial Management, Marketing, and Human Resources Management)旅游管理学 Tourist Management技术经济及管理学 Technology Economy and Management农林经济管理学 Agricultural and Forestry Economics & Management农业经济管理学 Agricultural Economics & Management林业经济管理学 Forestry Economics & Management公共管理学 Science of Public Management行政管理学 Administration Management社会医学与卫生事业管理学 Social Medicine and Health Management教育经济与管理学 Educational Economy and Management社会保障学 Social Security土地资源管理学 Land Resource Management图书馆、情报与档案学 Science of Library, Information and Archival图书馆学 Library Science情报学 Information Science档案学 Archival Science.. .. .. ..参考.资料。
机械工程专业英语第二版必考翻译(完整版)
1.With low-power machinery or vehicles the operator can usually apply sufficient force through a simple mechanical linkage from the pedle or handle to the stationary part of the brake. In many cases, however, this force must be multiplied by using an elaborate braking system（P5.）用低能机器或传力工具，操作者通过向踏板或把手的一个简单机械连接构件作用足够的力量到车闸固定的部分。
大多数情况，然而，用一个详细（复杂）的车闸系统使这个力量成倍增加。
2.The fundamental principle involved is the use of compressed air acting through a piston in a cylinder to set block brakes on the wheels. The action is simultaneous on the wheels of all thecars in the train. The compressed air is carried through a strong hose from car to car withcouplings between cars; its release to all the separate block brake units, at the same time, is controlled by the engineer. (Braking Systems)（ P5）相关的基本原理是使用压缩气体，通过气缸内的活塞将闸块压在车轮起作用。
机械类专业词汇中英文对照翻译表大全
机械类专业词汇中英文对照翻译表大全机械类专业词汇表一画一字螺丝批slot type screwdriver 一点透视 one-point perspective 二画二合一黏合剂 epoxy resin adhesive 二合胶；混合胶 epoxy glue 二维的；平面的 two-dimensional 二进制 binary 二极管；整流子 diode 二号螺丝攻 second tap 二路开关 two-way switch 十进制的；公制的 metric 人工制品 artefact 人造板 man-made board 人体工程学ergonomics 。
human engineering 人体尺寸 human dimension 人体测量学anthropometry 。
anthropometrics 刀片 blade 刀身 blade 刀具 tool 刀具溜座 carriage 刀柱 tool post 刀架 tool rest 刀架底座 tool rest bracket 刀座帷；床鞍 apron 刀座鞍；溜板座 saddle 力 force 力三角形 triangle of force力平行四边形 parallelogram of force 力多边形；多边形力学 polygon of force 力的分解 force resolution 力架；亮漆 lacquer 力矩 moment 力偶couple 力矩定律 law of moment 力-距离图表 force-distance graph 力图 force diagram 力线 line of force 力点 effort 十字榫 cross halving joint 十字螺丝 Philip's head screw 十字螺丝批 Philip's type screwdriver 丁字尺； T 尺 tee square 三画三爪夹头 three-jaw chuck 三角尺 set square 三角形结构系杆 triangulation tie 三角锉 triangular file 三维的；立体的 three-dimensional 三氯甲烷；哥罗芳chloroform 三聚氰 ?胺；蜜胺 melamine 三点透视three-point perspective 上油漆 painting 上釉enamelling 凡立水 varnish 叉形顶尖 fork centre 口罩 mask 士力；虫漆 shellac 士巴拿；扳手 spanner 大芯夹板；宽条芯夹板 blockboard 。
机械专业英语1Special English for Mechanical Engineering
Special English for Mechanical Engineering
机械工程专业英语的特点
1. 单词特点
(1) 专业性词汇较多，且词形复杂，记忆难度大。
chrome-moly steel — 铬钼钢
antifriction bearing— 滚动轴承
epicyclic gear— 行星齿轮
A-frame A形架
V-slot V形槽 O-ring O形环
Y-connection Y形连接（星形连接） zigzag wave 锯齿形波
U-shaped magnet 马蹄形磁铁
V-belt 三角皮带
cabinet file 半圆锉
twist drill 麻花钻 X-ray X射线
机械工程专业英语的特点
slide-crank mechanism —曲柄滑块机构
detail drawing — 零件图
four-bar linkage —四连杆机构
构词法
（i）派生法-在一个词的前面或后面加上词缀来构成新词 的方法。
前缀：一般词义变化，词性不变。
anti-反，防；如antiknock抗震的，，antinoise抗噪声的， dis-不，相反；如discharge放电 pre-预先，在前；如preheat预热，preamplifier前置放大器 semi-半：semiconductor半导体，semiautomatic半自动化的
laser
受激辐射式光频放大器镭射
（2）计量单位名称一般用音译。有些还可以进一步简化。
hertz 赫兹（频率） 赫
newton 牛顿（力、重量） 牛
pascal 帕斯卡（压力、强度） 帕 watt 瓦特（功率）瓦
机械设计专业术语的英语翻译
安全系数 safety factor; factor of safety安全载荷 safe load包角 angle of contact比例尺 scale比热容 specific heat capacity表面质量系数 superficial mass factor表面传热系数 surface coefficient of heat transfer表面粗糙度 surface roughness残余应力 residual stress齿宽 face width齿轮 gear带传动 belt driving当量载荷 equivalent load刀具 cutter导程 lead等效力 equivalent force低副 lower pair（疲劳）点蚀 pitting垫圈 gasket动力粘度 dynamic viscosity动压力 dynamic reaction动载荷 dynamic load端面 transverse plane锻造 forge对称循环应力 symmetry circulating stress额定寿命 rating life额定载荷 load rating法面参数 normal parameters法面模数 normal module法向齿廓 normal tooth profile防振装置 shockproof device分度圆 reference circle; standard (cutting) pitch circle复合轮系 compound (or combined) gear train高副 higher pair功 work工况系数 application factor工艺设计 technological design工作阻力矩 effective resistance moment公法线 common normal line功率 power功能分析设计 function analyses design构件 link鼓风机 blower惯性力 inertia force 滚动体 rolling element滚针 needle roller滚子 roller滚子从动件 roller follower滚子链 roller chain 合力矩 resultant moment of force横坐标 abscissa滑块 slider机电一体化系统设计 mechanical-electrical integration system design机构 mechanism机构综合 synthesis of mechanism机器人操作器 manipulator机器人学 robotics技术经济评价 technical and economic evaluation机械 machinery机械创新设计 mechanical creation design, MCD机械系统设计 mechanical system design, MSD 机械动力分析 dynamic analysis of machinery机械动力设计 dynamic design of machinery机械动力学 dynamics of machinery机械的现代设计 modern machine design机械系统 mechanical system机械手 manipulator机械设计 machine design; mechanical design机械特性 mechanical behavior机械效率 mechanical efficiency机械原理 theory of machines and mechanisms基圆压力角 pressure angle of base circle节距 circular pitch; pitch of teeth节圆 pitch circle圆锥 pitch cone径向游隙 radial internal clearance径向载荷系数 radial load factor静平衡 static balance绝对运动 absolute motion抗压强度 compression strength空间机构 spatial mechanism空间连杆机构 spatial linkage力偶矩 moment of couple连杆 connecting rod, coupler连杆机构 linkage链传动装置 chain gearing轮系 gear train螺纹 thread (of a screw)螺旋副 helical pair螺旋机构 screw mechanism脉动载荷 fluctuating load密封带 seal belt摩擦力矩 friction moment摩擦系数 coefficient of friction摩擦圆 friction circle疲劳强度 fatigue strength偏心质量 eccentric mass偏距圆 offset circle偏心盘 eccentric曲轴 crank shaft驱动力 driving force驱动力矩 driving moment (torque)输出力矩 output torque输出轴 output shaft输入构件 input link顺时针 clockwise瞬心 instantaneous center死点 dead point四杆机构 four-bar linkage速度 velocity特性 characteristics调心球轴承 self-aligning ball bearing凸轮倒置机构 inverse cam mechanism凸轮机构 cam , cam mechanism凸缘联轴器 flange coupling退刀槽 tool withdrawal groove蜗杆 worm蜗杆传动机构 worm gearing蜗杆头数 number of threads蜗轮 worm gear小齿轮 pinion斜齿轮的当量直齿轮 equivalent spur gear of the helical gear心轴 spindle行星轮系 planetary gear train虚约束 redundant (or passive) constraint许用应力 allowable stress; permissible stress移动副 prismatic pair, sliding pair应力—应变图 stress-strain diagram优化设计 optimal design原动机 prime mover圆柱滚子轴承 cylindrical roller bearing圆柱副 cylindric pair圆柱凸轮 cylindrical cam圆柱蜗杆 cylindrical worm圆锥滚子轴承 tapered roller bearing原动件 driving link约束 constraint约束条件 constraint condition约束反力 constraining force运动副 kinematic pair 运动构件 moving link运动简图 kinematic sketch运动周期 cycle of motion运动粘度 kenematic viscosity载荷 load载荷—变形曲线 load—deformation curve 载荷—变形图 load—deformation diagram直齿圆柱齿轮 spur gear直齿锥齿轮 straight bevel gear直角坐标操作器 Cartesian coordinate manipulator直径系数 diametral quotient轴 shaft轴承盖 bearing cup轴承内径 bearing bore diameter轴承寿命 bearing life轴瓦、轴承衬 bearing bush轴端挡圈 shaft end ring轴向当量动载荷 dynamic equivalent axial load轴向当量静载荷 static equivalent axial load轴向基本额定动载荷 basic dynamic axial load rating轴向基本额定静载荷 basic static axial load rating轴向载荷 axial load轴向载荷系数 axial load factor主动件 driving link主动齿轮 driving gear主动带轮 driving pulley转动导杆机构 whitworth mechanism转轴 revolving shaft锥齿轮 bevel gear锥齿轮的当量直齿轮 equivalent spur gear of the bevel gear子程序 subroutine 子机构 sub-mechanism自动化 automation自锁 self-locking自锁条件 condition of self-locking 自由度 degree of freedom, mobility总重合度 total contact ratio总反力 resultant force总效率 combined efficiency; overall efficiency组成原理 theory of constitution组合齿形 composite tooth form组合安装 stack mounting组合机构 combined mechanism阻抗力 resistance最大盈亏功 maximum difference work between plus and minus work纵向重合度 overlap contact ratio纵坐标 ordinate组合机构 combined mechanism最少齿数 minimum teeth number最小向径 minimum radius作用力 applied force坐标系 coordinate frame。
大学专业英文翻译
建筑系：Architecture土木工程：Civil Engineering流体机械及工程Fluid Machinery and Engineering制冷及低温工程Refrigeration and Cryogenic Engineering化工过程机械Chemical Process Equipment电气工程Electrical Engineering电机与电器Electric Machines and Electric Apparatus电力系统及其自动化Power System and its Automation高电压与绝缘技术High V oltage and Insulation Technology电力电子与电力传动Power Electronics and Power Drives电工理论与新技术Theory and New Technology of Electrical Engineering电子科学与技术Electronics Science and Technology物理电子学Physical Electronics电路与系统Circuits and Systems微电子学与固体电子学Microelectronics and Solid State Electronics电磁场与微波技术Electromagnetic Field and Microwave Technology信息与通信工程Information and Communication Engineering通信与信息系统Communication and Information Systems信号与信息处理Signal and Information Processing控制科学与工程Control Science and Engineering控制理论与控制工程Control Theory and Control Engineering检测技术与自动化装置Detection Technology and Automatic Equipment系统工程Systems Engineering模式识别与智能系统Pattern Recognition and Intelligent Systems导航、制导与控制Navigation, Guidance and Control计算机科学与技术Computer Science and Technology计算机软件与理论Computer Software and Theory计算机系统结构Computer Systems Organization计算机应用技术Computer Applied Technology建筑学Architecture建筑历史与理论Architectural History and Theory建筑设计及其理论Architectural Design and Theory城市规划与设计（含风景园林规划与设计）Urban Planning and Design (including Landscape Planning and Design)建筑技术科学Building Technology Science土木工程Civil Engineering岩土工程Geotechnical Engineering结构工程Structural Engineering市政工程Municipal Engineering供热、供燃气、通风及空调工程Heating, Gas Supply, Ventilating and Air Conditioning Engineering防灾减灾工程及防护工程Disaster Prevention and Reduction Engineering and Protective Engineering桥梁与隧道工程Bridge and Tunnel Engineering水利工程Hydraulic Engineering水文学及水资源Hydrology and Water Resources水力学及河流动力学Hydraulics and River Dynamics水工结构工程Hydraulic Structure Engineering水利水电工程Hydraulic and Hydro-Power Engineering港口、海岸及近海工程Harbor, Coastal and Offshore Engineering测绘科学与技术Surveying and Mapping大地测量学与测量工程Geodesy and Survey Engineering摄影测量与遥感Photogrammetry and Remote Sensing地图制图学与地理信息工程Cartography and Geographic Information Engineering 化学工程与技术Chemical Engineering and Technology化学工程Chemical Engineering化学工艺Chemical Technology生物化工Biochemical Engineering应用化学Applied Chemistry工业催化Industrial Catalysis地质资源与地质工程Geological Resources and Geological Engineering矿产普查与勘探Mineral Resource Prospecting and Exploration地球探测与信息技术Geodetection and Information Technology地质工程Geological Engineering矿业工程Mineral Engineering采矿工程Mining Engineering矿物加工工程Mineral Processing Engineering安全技术及工程Safety Technology and Engineering石油与天然气工程Oil and Natural Gas Engineering油气井工程Oil-Gas Well Engineering油气田开发工程Oil-Gas Field Development Engineering油气储运工程Oil-Gas Storage and Transportation Engineering纺织科学与工程Textile Science and Engineering纺织工程Textile Engineering纺织材料与纺织品设计Textile Material and Textiles Design纺织化学与染整工程Textile Chemistry and Dyeing and Finishing Engineering服装设计与工程Clothing Design and Engineering轻工技术与工程The Light Industry Technology and Engineering制浆造纸工程Pulp and Paper Engineering制糖工程Sugar Engineering发酵工程Fermentation Engineering皮革化学与工程Leather Chemistry and Engineering交通运输工程Communication and Transportation Engineering道路与铁道工程Highway and Railway Engineering交通信息工程及控制Traffic Information Engineering & Control交通运输规划与管理Transportation Planning and Management载运工具运用工程Vehicle Operation Engineering船舶与海洋工程Naval Architecture and Ocean Engineering船舶与海洋结构物设计制造Design and Construction of Naval Architecture and Ocean Structure轮机工程Marine Engine Engineering水声工程Underwater Acoustics Engineering航空宇航科学与技术Aeronautical and Astronautical Science and Technology飞行器设计Flight Vehicle Design航空宇航推进理论与工程Aerospace Propulsion Theory and Engineering航空宇航器制造工程Manufacturing Engineering of Aerospace Vehicle人机与环境工程Man-Machine and Environmental Engineering兵器科学与技术Armament Science and Technology武器系统与运用工程Weapon Systems and Utilization Engineering兵器发射理论与技术Armament Launch Theory and Technology火炮、自动武器与弹药工程Artillery, Automatic Gun and Ammunition Engineering军事化学与烟火技术Military Chemistry and Pyrotechnics核科学与技术Nuclear Science and Technology核能科学与工程Nuclear Energy Science and Engineering核燃料循环与材料Nuclear Fuel Cycle and Materials核技术及应用Nuclear Technology and Applications辐射防护及环境保护Radiation and Environmental Protection农业工程Agricultural Engineering农业机械化工程Agricultural Mechanization Engineering农业水土工程Agricultural Water-Soil Engineering农业生物环境与能源工程Agricultural Biological Environmental and Energy Engineering农业电气化与自动化Agricultural Electrification and Automation林业工程Forestry Engineering森林工程Forest Engineering木材科学与技术Wood Science and Technology林产化学加工工程Chemical Processing Engineering of Forest Products环境科学与工程Environmental Science and Engineering环境科学Environmental Science环境工程Environmental Engineering生物医学工程Biomedical Engineering食品科学与工程Food Science and Engineering食品科学Food Science粮食、油脂及植物蛋白工程Cereals, Oils and Vegetable Protein Engineering农产品加工及贮藏工程Processing and Storage of Agriculture Products水产品加工及贮藏工程Processing and Storage of Aquatic Products农学Agriculture作物学Crop Science作物栽培学与耕作学Crop Cultivation and Farming System作物遗传育种学Crop Genetics and Breeding园艺学Horticulture果树学Pomology蔬菜学Olericulture茶学Tea Science农业资源利用学Utilization Science of Agricultural Resources土壤学Soil Science植物营养学Plant Nutrition植物保护学Plant Protection植物病理学Plant Pathology农业昆虫与害虫防治Agricultural Entomology and Pest Control农药学Pesticide Science畜牧学Animal Science动物遗传育种与繁殖Animal Genetics, Breeding and ReproductionScience动物营养与饲料科学Animal Nutrition and Feed Science草业科学Practaculture Science特种经济动物饲养学（含蚕、蜂等）The Rearing of Special-type EconomicAnimals (including Silkworm, Honeybees, etc.)兽医学Veterinary Medicine基础兽医学Basic Veterinary Medicine预防兽医学Preventive Veterinary Medicine临床兽医学Clinical Veterinary Medicine林学Forestry林木遗传育种学Forest Tree Genetics and Breeding森林培育学Silviculture森林保护学Forest Protection森林经理学Forest Management野生动植物保护与利用Wildlife Conservation and Utilization园林植物与观赏园艺Ornamental Plants and Horticulture水土保持与荒漠化防治Soil and Water Conservation and Desertification Combating水产学Fisheries Science水产养殖学Aquaculture Science捕捞学Fishing Science渔业资源学Science of Fisheries Resources医学Medicine基础医学Basic Medicine人体解剖与组织胚胎学Human Anatomy, Histology and Embryology免疫学Immunology病原生物学Pathogenic Organisms病理学与病理生理学Pathology and Pathophysiology法医学Forensic Medicine放射医学Radiation Medicine航空航天与航海医学Aerospace and Nautical medicine临床医学Clinical Medicine内科学（含心血管病学、血液病学、呼吸系病学、消化系病学、内分泌与代谢病学、肾脏病学、风湿病学、传染病学）Internal medicine (including Cardiology, Hematology, Respiratory, Gastroenterology, Endocrinology and Metabolism, Nephrology, Rheuma-tology, InfectiousDiseases)儿科学Pediatrics老年医学Geriatrics神经病学Neurology精神病与精神卫生学Psychiatry and Mental Health皮肤病与性病学Dermatology and Venereology影像医学与核医学Imaging and Nuclear Medicine临床检验诊断学Clinical Laboratory Diagnostics护理学Nursing外科学（含普通外科学、骨外科学、泌尿外科学、胸心血管外科学、神经外科学、整形外科学、烧伤外科学、野战外科学）Surgery (General Surgery, Orthopedics, Urology, Cardiothoracic Surgery, Neurosurgery, Plastic Surgery, Burn Surgery, Field Surgery)妇产科学Obstetrics and Gynecology眼科学Ophthalmic Specialty耳鼻咽喉科学Otolaryngology肿瘤学Oncology康复医学与理疗学Rehabilitation Medicine & Physical Therapy运动医学Sports Medicine麻醉学Anesthesiology急诊医学Emergency Medicine口腔医学Stomatology口腔基础医学Basic Science of Stomatology口腔临床医学Clinical Science of Stomatology公共卫生与预防医学Public Health and Preventive Medicine流行病与卫生统计学Epidemiology and Health Statistics劳动卫生与环境卫生学Occupational and Environmental Health营养与食品卫生学Nutrition and Food Hygiene儿少卫生与妇幼保健学Maternal, Child and Adolescent Health卫生毒理学Hygiene Toxicology军事预防医学Military Preventive Medicine中医学Chinese Medicine中医基础理论Basic Theories of Chinese Medicine仪器科学与光电工程学院 School of Instrument Science and Opto-electronic Engineering1、测控技术与仪器 Measurement & Control Technology and Instrument2、光信息科学与技术 Optic Information Science & Technology机械与汽车工程学院 School of Machinery and Automobile Engineering3、车辆工程 Vehicles Engineering4、工业工程 Industrial Engineering5、工业设计 Industry Design6、过程装备与控制工程 Process Equipment & Control Engineering7、机械设计制造及其自动化 Machine Design & Manufacture & Its Automation8、交通工程 Transportation Engineering9、热能与动力工程 Thermal Energy & Power Engineering材料科学与工程学院 School of Material Science and Engineering10、金属材料工程 Metal Materials Engineering11、材料物理 Materials Physics12、无机非金属材料工程 Inorganic Non-metallic Materials Engineering13、材料成型及控制工程 Material Forming & Control Engineering电气与自动化工程学院 School of Electric Engineering and Automation14、电气工程及其自动化 Electric Engineering and Automation15、生物医学工程 Biomedical Engineering16、自动化 Automation计算机与信息学院 School of Computer and Information17、计算机科学与技术 Computer Science & Technology18、电子信息工程 Electronic Information Engineering19、电子信息科学与技术 Electronic Information Science & Technology20、通信工程 Communications Engineering21、信息安全Information Security化学工程学院 School of Chemical Engineering22、高分子材料与工程 Macromolecule Material and Engineering23、化学工程与工艺 Chemical Engineering and Technics24、制药工程 Pharmacy Engineering25、应用化学 Applied Chemistry土木建筑工程学院 School of Civil Engineering26、给排水工程 Water Supply & Drainage Engineering27、工程力学 Engineering Mechanics28、水利水电工程 Hydraulic and Hydro-Power Engineering29、土木工程 Civil Engineering30、建筑环境与设备工程 Architectural Environment & Equipment Engineering 建筑与艺术学院 School of Architecture and Arts31、城市规划 Urban Planning32、建筑学 Architecture33、艺术设计 Artistic Design资源与环境学院 School of Resources and Environment34、地理信息系统 Geographic Information System35、环境工程 Environment Engineering36、勘查技术与工程 Exploration Technology & Engineering37、资源勘查工程 Resources Exploration Engineering理学院 School of Sciences38、电子科学与技术 Electronic Science & Technology39、数学与应用数学 Applied Mathematics40、微电子学 Microelectronics41、信息与计算科学 Science of Information & Computation42、应用物理学 Applied Physics管理学院 School of Management43、电子商务 Electronic Commerce44、会计学 Accounting45、工商管理 Business Management46、劳动与社会保障 Labour and Social Security47、信息管理与信息系统 Information Management & System48、旅游管理 Tourism Management49、市场营销 Marketing人文经济学院 School of Humanities and Economics50、财政学 Finance51、广告学 Advertisement52、国际经济与贸易 International Economy & Trade53、经济学 Economics54、思想政治教育 Education in Ideology and Politics55、英语 English56、法学 Law57、社会工作 Social Work生物与食品工程学院 School of Biotechnology and Food Engineering58、生物工程 Bioengineering59、生物技术 Biotechnology60、食品科学与工程 Food Science and Engineering。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
机械专业英文翻译集团文件版本号：（M928-T898-M248-WU2669-I2896-DQ586-M1988）启动轴 starting axle 启动齿轮 starting gear 启动棘轮 starting ratchet wheel 复位弹簧 restoring, pull back spring弹簧座 spring seating 摩擦簧 friction spring 推力垫圈 thrust washer 轴挡圈 axle bumper ring下料 filling 切断 cut滚齿机 gear-hobbing machine剪料机 material-shearing machine车床 lathe 拉床 broaching machine垂直度 verticality, vertical extent 平行度 parallelism 同心度homocentricity 位置度 position 拉伤pulling damage 碰伤 bumping damage缺陷 deficiency 严重缺陷 severe deficiency摩擦力 friction 扭距 twist滑动 glide 滚动 roll打滑 skid 脱不开 can ’t seperate不复位 can ’t restore 径 diameterM 值 = 跨棒距 test r span公法线 common normal li弹性 elasticity频率特性 frequency characteristic误差 error 响应 response 定位 allocation 机床夹具 jig动力学 dynamic 运动学 kinematic 静力学 static分析力学 analyse mechanics 拉伸 pulling 压缩 hitting机床 machine tool刀具 cutter摩擦 friction联结 link传动 drive/transmission 轴 shaft剪切 shear扭转 twist弯曲应力 bending stress 三相交流电 three-phase AC 磁路 magnetic circles变压器 transformer异步电动机 asynchronous motor几何形状 geometrical精度 precision正弦形的 sinusoid交流电路 AC circuit机械加工余量 machining allowance变形力 deforming force变形 deformation电路 circuit 半导体元件semiconductorelement拉孔 broaching装配 assembling加工 machining液压 hydraulicpressure切线 tangent机电一体化mechanotronicsmechanical-electricalintegration稳定性 stability介质 medium液压驱动泵 fluidclutch液压泵 hydraulicpump阀门 valve失效 invalidation强度 intensity载荷 load应力 stress安全系数 safty factor可靠性 reliability螺纹 thread螺旋 helix键 spline销 pin滚动轴承 rolling bearing滑动轴承 sliding bearing弹簧 spring制动器 arrester brake十字结联轴节 crosshead联轴器 coupling链 chain皮带 strap精加工 finish machining粗加工 rough machining变速箱体 gearbox casing腐蚀 rust氧化 oxidation磨损 wear耐用度 durability机械制图Mechanical drawing投影 projection视图 view剖视图 profile chart标准件 standard component 零件图 part drawing装配图 assembly drawing尺寸标注 size marking技术要求technical requirements刚度 rigidity内力 internal force位移 displacement截面 section疲劳极限 fatigue limit断裂 fracture塑性变形 plastic distortion 脆性材料 brittleness material刚度准则 rigidity criterion 垫圈 washer垫片 spacer 直齿圆柱齿轮straight toothedspur gear斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图 kinematicsketch齿轮齿条 pinion andrack蜗杆蜗轮 worm andworm gear虚约束 passiveconstraint曲柄 crank摇杆 racker凸轮 cams反馈 feedback发生器 generator直流电源 DCelectrical source门电路 gate circuit外圆磨削 external grinding内圆磨削 internal grinding平面磨削 plane grinding变速箱 gearbox离合器 clutch绞孔 fraising绞刀 reamer螺纹加工 thread processing螺钉 screw铣削 mill铣刀 milling cutter功率 power工件 workpiece齿轮加工 gear mechining齿轮 gear主运动 main movement主运动方向direction of main movement进给方向 direction of feed进给运动 feed movement合成进给运动resultant movement of feed合成切削运动resultant movement of cutting合成切削运动方向 direction of resultant movement of cutting切削深度 cutting depth前刀面 rake face刀尖 nose of tool前角 rake angle后角 clearance angle龙门刨削 planing主轴 spindle主轴箱 headstock卡盘 chuck加工中心 machining center 车刀 lathe tool车床 lathe镗削 bore集成电路 integrate circuit 挡板 orifice plate残余应力 residual stress 套筒 sleeve扭力 torsion 冷加工 coldmachining电动机 electromotor汽缸 cylinder过盈配合interference fit热加工 hotwork摄像头 CCD camera倒角 roundingchamfer优化设计 optimaldesign工业造型设计industrial mouldingdesign有限元 finiteelement滚齿 hobbing插齿 gear shaping伺服电机 actuatingmotor铣床 millingmachine钻床 drill machine镗床 boring machine步进电机 stepper motor丝杠 screw rod导轨 lead rail组件 subassembly可编程序逻辑控制器Programmable LogicController PLC毛坯 rough桁架 truss轴线 axes逻辑电路 logic circuit触发器 flip-flop脉冲波形 pulse shape数模 digital analogy液压传动机构fluid drive mechanism机械零件 mechanical parts产品突出特点ProductHighlights特别优惠 special offersAssembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch ofSPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resourcedepartment人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy sectionsupervisor =vicesection superisor副课长groupleader/supervisor组长line supervisor线长assistant manager助理to move, to carry,to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skrpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturingprocedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective productlabel不良标签identifying sheetlist标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) withexposed fingers割手套missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a littlebigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slipperyscrew head螺丝滑头slipped screwhead/shipperyscrew thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up tograde合格not up to grade,not qualified不合格material change,stock change材料变更feature change 特性变更evaluation评估prepare for, makepreparations for 准备parameters参数rotating speed,revolution转速manufacturemanagement制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing outpress冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock 库存receive领取approval examine and verify 审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward andhand in提报safe stock安全库存acceptance =receive验收to notice通知application formfor purchase请购单consume,consumption消耗to fill in填写abrasion磨损die 模具figure file, chartfile图档cutting die,blanking die冲裁模progressive die,follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=sidescrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block forlocation定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch =stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块barreling 滚光加工 belling 压凸加工bending 弯曲加工 blanking 下料加工bulging 撑压加工 burring 冲缘加工cam die bending 凸轮弯曲加工caulking 合加工coining 压印加工compressing 压缩加工compression bending押弯曲加工 crowning凸面加工curl bending 卷边弯曲加工 curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 叠板裁断 drawing 引伸加工drawing withironing 抽引光滑加工 embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工 finishblanking 光制下料加工finishing 精整加工 flanging凸缘加工folding 折边弯曲加工 folding摺叠加工forming 成形加工 impactextrusion 冲击挤压加工indenting 压痕加工 ironing引缩加工knurling 滚花 lock seaming固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工 notching 冲口加工parting 分断加工 piercing 冲孔加工progressive bending 连续弯曲加工 progressive blanking 连续下料加工progressive drawing 连续引伸加工 progressive forming 连续成形加工reaming 铰孔加工 restriking 二次精冲加工riveting 接加工 roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工 scrapless machining 无废料加工seaming 折弯重叠加工 shaving 缺口修整加工shearing 切断加工 sizing 精压加工/矫正加工slitting 割缝加工 spinning 卷边接staking 固 stamping 锻压加工swaging 挤锻压加工 trimming 整缘加工upsetting 锻粗加工 wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴 blank determination 胚料展开bottom slide press下传动式压力机board drop hammer板落锤brake 煞车 buckle剥砂面camlachie cramp 铸包 casting on flat合chamotte sand 烧磨砂 charging hopper加料漏斗clearance 间隙closed-die forging合模锻造clump 夹紧 clutch离合器clutch brake 离合器制动器 clutch boss离合器轮壳clutch lining 离合器覆盖 coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱 connection screw连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架 crank 曲柄轴crankless 无曲柄式 crosscrank 横向曲轴cushion 缓冲 depression 外缩凹孔dial feed 分度送料 dieapproach 模口角度die assembly 合模 diecushion 模具缓冲垫die height 冲压闭合高度 dielife 模具寿命die opening 母模逃孔 diespotting press 调整冲模用压力机double crank press 双曲柄轴冲床 draght angle 逃料倾斜角edging 边锻伸 embedded core 加装砂心feed length 送料长度 feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹 fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼後熔渣fly wheel 飞轮 fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架 friction 摩擦friction brake 摩擦煞车 gap shear 凹口剪床gear 齿轮 gib 滑块引导部gripper 夹具 gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinionpress 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床 hopperfeed 料斗送料idle stage 空站inching 微调尺寸isothermal forging恒温锻造 key clutch键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器 lowerdie 下模micro inching device 微寸动装置 microinching equipment微动装置motor 马达 moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device防超载装置 pinch roll 导正滚轮pinion 小齿轮 pitch 节距pressfit 压入 progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统 regrinding 再次研磨releasing 松释动作 reversedblanking 反转下料robot 机器人 roll formingmachine 辊轧成形roll forming machine 辊轧成形机 roll release 脱辊roller feed 辊式送料 roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀 scrap press 废料冲床seamless forging 无缝锻造separate 分离shave 崩砂 shear angle 剪角sheet loader 薄板装料机 shot 单行程工作shrinkage fit 收缩配合 shut height 闭合高度sieve mesh 筛孔 sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机 spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置 strippingpressure 弹出压力stroke 冲程 takeout device 取料装置toggle press 肘杆式压力机 transfer 传送transfer feed 连续自动送料装置turrent punch press转塔冲床two speed clutch 双速离合器 uncoiler闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机业务与贸易关连用语accept order 接受订货 account 帐户after service 售后服务amendment 修正annual sales 年销售额 atsight 见票即付balance 余额 bank draft 汇票bargain goods 廉价品 batch批次bid 出价 bid sales 投标买卖bill of landing 提单 billsreceivable 应收票据brand 品牌 bulk cargo 散装货business transaction 商业交易 buyer 买方carbon copy 打字副本 cargocollection 揽货carton 纸箱 cash in advance预付现金catalogue 型录 cheque 支票CLF 运费保险费在内价格 claim索赔clearance goods 清仓品commision 佣金commission 批发商 complain 抱怨container 货柜correspondence bank 往来银行cost 成本 cost and freight; C&F 含运费价格custom broker 报关行customer 客户D/A 承兑交单 D/P 付款交单deferred payment 分期付款deferred shipment 分期装运delivery on spot 当场交货delivery time 交期delivery order 交货单discount 折扣discount on draft 贴现documentary draft 跟单汇票down payment 订金 enclosure 附件endorsement 背书 enquete 调查exhibition 展览会 export 出口factory visiy 工厂参观 favourableprice 合宜价格foreign exchange 外汇 free on board 船上交货价idea price 希望价格import 进口Japanese Industrial日本工业规格invoice 发票L/C 信用状 margin利润market 市价 netweight 净重no payment 拒绝付款odd item 零头offer 报价 openaccount 交互计算order 订单 overlooked 疏漏packing 包装pamphlet 小册子partial shipment 分批装船patent 专利paying price 合算价格payment method 付款方式port of destination 目地港port of trans-shipment 转口港price 价格 price decending减价price rising 涨价procurement 采办prompt delivery 即时交货purchase 购入purchasing agent 采购代理商quotation 报价单rebate 回扣 reference 查询remittance 汇款 repeat order追加订货request letter 请求函 rumor风评second hand goods 二手货shipper 货主shipping 装船 shipping mark 麦头shipment 出货 sold out 卖完sole agent 总代理商 special discount 特别折扣specification 规格 sample order 指样订货standing 信用情形 storage charge 仓租subcontract 外包 subject to final confirmation 有待确认之报价supplier 供应商 T/T 电汇tie-in sale 搭售 trade fair 商展会trans-shipment 转运transferred 已转运wharf 码头。