博科BrocadeSAN交换机常用命令

博科BrocadeSAN交换机常用命令

博科Brocade SAN交换机通用命令

1。查看IP地址命令............................................................................................................2 2.查看固件版本.......................................................................................................2 3.查看开关状态 (2)

4.查看交换机许可证-id........................................................................................3

5.配置ZONE........................................................................................................... .......3

6.查看区域配置文件.................................................................................................………4

7.查看区域..................................................................................................................

5 8.检查系统日志信息...................................................................................................

6 9.停工.................................................................................................................. ................6 10.设置博科锦交换机的IP地址.............................................................................6 11.博科brocade交换机查看操作系统版本信息.................................................................6 12.

锦缎交换机添加许可证授权信息 (7)

13.查看锦缎交换机许可证授权信息..........................................................7 14.Brocade Slikworm 300交换机许可证......................................................7 15.博科锦缎交换机密码更改命令..........................................................................7 16.博科锦缎交换机密码重置..................................................................................7 17.登录后，使用passwddefault命令恢复出厂密码................................................9 18.交换机升级..................................................................................................................

9 19.帮助信息 (13)

1。查看IP地址命令

swd 77:admin > IP addr show switch

以太网IP地址:10.77.77.77以太网子网掩码:255.255.255.0光纤通道IP 地址:无光纤通道子网掩码:无网关IP地址:无DHCP:offwd 77:admin > 2。查看固件版本swd 211:admin >

swd 211:admin >固件显示

appl主/辅助版本

-FOS 6 . 2 . 1 6 . 2 . 1

3。查看交换机状态

swd211:admin >交换机显示

rbash:交换机显示:未找到命令swd211:admin >交换机显示交换机名称:swd211交换机类型:34.0

交换机状态:在线交换机模式:本机交换机角色:主体交换机域:1

交换机id:fffc 01

交换机Wwn: 10:00:00:05:1e 199 0 0 id N2在线F-端口50:08:05:f3:00:1b:4e:91 1 1 id N4在线F-端口10:00:00:00:00:C9:53:B2:8d 2 2 id N4在线F-端口10:00:00:00:00:C9:53:B3:C1 3 id N4在线F-端口10:00:00:00:C9:53:B3:C2 4 id N4 199 8 8 id N4在线F端口50:01:43:80:04:C7:87:D8 9 id N4在线F端口50:01:43:80:04:C7:87:DC 10 10 id N4在线F端口50:01:43:80:06:31:cf:7c 11-N4 No _ Module 12 12-N4 No _ Module 13 13-N4 No _ Module 查看交换机许可证-id swd 211:admin >

swd 211:admin > licensee show 10:00:00:05:1e:02:a2:10swd 211:admin >

5。配置ZONE事例:

1)创建别名

>别名创建“Eng_Host”，“1，0”

>别名创建“Eng_Stor”，“1，4；1，5” >alicreate “Mkt_Host “，” Mtktwwn “

> alicreate “ Mkt _ Stor “，” s3wwns4wwns5wwn “ 2)创建区域