18650-2000电芯规格书
SB18650S1800mAh规格书 2
*电池具有使用寿命，如果使用电池的设备的工作时间比平常少得多，要对电池进行更换。
*电池寿命终止后要立刻从设备中取出。
*当长期不用时，要将电池从设备中取出并放在低温低湿的环境中保存。
*电池应在远离静电的场所进行充电、使用和储存。
*如果电池的接线端变脏，在使用之前用干布擦净。
6
浸泡性能
不爆炸、不起火
在室温下将充满电的电池在清水里浸泡24小时
7
重物冲击
性能
不爆炸、不起火
将充满电的电池放置在一个平面上，将一重10㎏重锤自61cm高度自由落下，冲击在已固定在夹具中的电池（电池面积最大的面应与台面垂直）
5.3电芯可靠性特性
序号
项目
标准
测试方法
1
高温高湿实验
电池的工作性能、外观不受影响
合肥赛力新能源有限公司
锂离子电池规格书
电池型号：18650S/2000mAh
标称电压:3.7V
拟定:审核:批准:
合肥赛力新能源有限公司
地址：合肥市高新技术开发区香樟大道189号
电话：（0551）5774558
传真：（0551）5302123
邮编：230088
合肥赛力新能源有限公司
报告类别
产品规格书
部门
在环境温度为25±5℃的条件下，标准充电后静置10分钟，3C5A放电至3.00V，循环3次，当有一次放电达到标准，即可终止。
5
0.5C5A循环寿命
放电容量≥初始容量*70%
测试电池的初始状态和初始容量,在环境温度为25±5℃的条件下，以0.5C5A电流恒流放电至3.00V，再以0.5C5A电流恒流充电至4.20V，然后4.20V恒压充电至截止电流，静置10min，再进行下一个充放电循环，直至1000次循环。
EVE18650 2000MAH
3.2 Nominal Voltage 额定电压
3.70V
Discharge:0.2CmA 0.2C 放电(400mA)
3.2 AC Impedance Resistance 内阻
≤40mΩ
3.4 Discharge Cut-off Voltage 放电截至电压
3.00V
3.5 Load Voltage 负载电压(33Ω)
EVE18650
VER A
SPEC NO. EVE-SP-EVE18650-S-001-LF
PAGE DATE
5/13
2014-11-17
4 Outline Dimensions and Appearance 电池外形尺寸及外观
4.1 Outline Dimensions 外形尺寸 See attached drawing for 电池外形尺寸参见“EVE18650(Fig.1).外形尺寸图”。
HUIZHOU EVE ENERGY CO., LTD
MODEL
EVE18650 规格书
VER A
SPEC NO.
EVE-SP-EVE18650-S-001-LF
PAGE DATE
1/13
2014-11-17
Customer’s Name 客户名称： EVE-A004
File 文件编号：EVE-SP-EVE18650-S-001-LF Version 版本： A Date 日期： 2014-11-17
the cells shall not be cycled more than five times before the test. Unless otherwise defined, test and measurement shall be done under temperature of25±10℃ and relative humidity of 45~75%.
华亿源18650-2000规格书.doc
产品规格书电池类型：圆柱型锂离子电池电池型号：HYY18650-2000(带PTC)制 定 审 核 批 准3.0 电池性能3.1电化学性能序号项目标准测试方法1 常温放电性能放电容量/标称容量×100％A）0.2C5A ≥100％B）0.5C5A ≥98％C）1C5A ≥95％在1标准大气压，环境温度25℃±2℃，相对湿度为35％～85％的条件下，电池0.5C标准充电后（以下若没有特别说明，均在此条件下放置，皆按此充电方式），搁置10min，分别以0.2C5A、0.5C5A、1C5A、进行放电至下限电压2.75V，循环三次，当有一次达到标准，即达到标准要求（下同）。
2 常温荷电保持能力剩余容量≥标称容量*85％恢复容量≥标称容量*90％开路电压减小率≤3％内阻增加率≤20％测量电池的初始状态和初始容量，电池标准充电后，开路放置28天，测量电池最终状态；以0.2C5A放电至2.75V，测量电池的剩余容量；0.5C/0.2C测量电池的恢复容量。
可循环三次，当有一次达到标准，即达到标准要求。
1.0 基本特性型号18650-2000外壳材质镀镍钢标称容量（0.2C5A）2000mAh 额定电压 3.7V最大充电电压 4.2 V放电截至电压 2.75V最大充电电流 1 C5A最大放电电流 1 C5A 电池直径（包PVC套）≤18.40mm电池高度（包PVC套） ≤65.30mm电池重量(Approx.) ≤45.2g内阻（Max, at 1000Hz.）≤60 mΩ(充电态)标准0.5 C5A×7.5hrs充电方法(CC/CV) 快速 1 C5A×2.5hrs.放电方法标准0.2 C5A×6 hrs.充电0℃～45℃放电-10℃～50℃操作温度贮存-20℃～25℃2.0 外形图3 循环寿命容量≥标称容量*80％测量电池的初始状态和初始容量，0.5C/0.2C循环300次后测量电池的最终状态。
18650单电芯规格书
18650单电芯规格书BATTERY CO., LTD. DOC NO.: QR-WI-733-003-002/A REV. : APAGE: 1 of 8Specification Approval Sheet (cylinder Cell) 产品规格确认书（圆柱电池）Model/型号：ZZ18650Capacity/容量：1500mAhVoltage/电压：3.7V制定（Prepared By）审核（CheckedBy）批准（ApprovedBy）DOC NO.: QR-WI-733-003-002/A REV. : APAGE: 2 of 81.0基本特性Basic performance型号Model BJ18650P 外壳材质Can Material 镀镍钢Nickel-plated 标称容量NominalCapacity，（0.2C5A）1300mAh额定电压Nominal 3.70V 充电截止电压Max 4.20 V 放电终止电压 2.80V 最大充电电流Max.Charge Current1C5A标准持续放电流10C5A最大瞬间放电电流Max. Discharge Curent20 C5A电池最大直径（光壳）18.5电池最大高度（光壳）66mm 电池重量(Approx.) 约36g 内阻（Max, at 1000Hz.）≤16mΩ充电方法Charge 标准0.2C5A×快速 1 C5A×操作温度Operating Temperature 充电Charge0℃～45℃放电Discharge-20℃～60℃贮存Storage-10℃～45℃2.0 外形图figure2.1结构图Structure3.0 主要放电曲线Mainly capability graphBJ18650P-1300mAh 15C Discharge Cruve BJ18650P-1300mAh 1C Charge CruveBJ18650P-1300mAh 13C Cycle Life BJ18650P-1300mAh -20℃Discharge CruveDOC NO.: QR-WI-733-003-002/A REV. : APAGE: 3 of 84.0 电池性能Characteristic若没有特别说明，电池在做各项试验前，均需在86KPa～106 KPa大气压，环境温度20℃±5℃，相对湿度为45％～75％的条件下，以0.2C5A恒流放电至终止电压2.8V，并在收到产品两周内进行以下试验。
18650（2600mAh 3.7V）规格确认书说明书
CUSTOMER NO:Specification Approval Sheet规格确认书MODEL /型号: 18650（2600mAh 3.7V ）Prepared By/Date 编 制/日 期Checked By/Date 审 核/日 期Approved By/Date 批 准/日 期杨小莹/2012-5-16Customer Approval 客户确认Signature/签 字Date/日 期Company Name/公司名称Company Stamp/公司印章Amendment Records/修正记录Revision 版本Description/记述Prepared by编制Approved by批准Date/日期A FirstPublish 杨小莹Content/目录2. Model/型号Page 43.Cell Specification/电芯规格说明Page 4/54. Battery/Cell performance test Criteria/电池性能标准Page 6 4.1 Appearance inspection by visual/外观目测Page 6 4.2 Environmental test condition/外界环境条件Page6 4.3 Electrical characteristics/电气特性Page 6/7 4.4 Mechanical characteristics/机械特性Page 74.5 Safety performance/安全性能Page 85. Cell initial Dimensions/电芯初始尺寸Page 96. CAUTIONS IN USE(谨慎使用)Page 107. Period of Warranty/保质期Page 108. Storage of the Batteries/电池的存放Page 109. Other The Chemical Reaction/其它化学反应Page 1010. Note/注释Page 10 2. Model/型号Page 41 Scope/适用范围This specification is applies to describe the related Battery product in this Specification and the Battery/cell supplied by CTECHI only.本说明书只适用于描述本规格书中相关的产品。
18650单电芯2000倍率型规格书
倍率型圆柱电池商丘市迈科新能源有限公司DOC NO.:REV. :PAGE: 1 of 8Specification Approval Sheet (cylinder Cell) 产品规格确认书（圆柱电池）Model/型号： 18650PCapacity/容量 2000mAhVoltage/电压： 3.7V制定（Prepared By）审核（Checked By）批准（Approved By）温庆 屈明明 熊胜任4.0 电池性能Characteristic若没有特别说明，电池在做各项试验前，均需在86KPa～106 KPa大气压，环境温度20℃±5℃，相对湿度为45％～75％的条件下，以0.2C5A恒流放电至终止电压2.75V，并在收到产品两周内进行以下试验。
Without special instructions, the following tests should be done under the condition of : temperature(20℃±5℃), atmospheric pressure (86KPa～106 Kpa), relative humidity (45％～75％), and the tests should be done within two weeks after receiving the products.一些术语的定义：the definitions of some nomenclatures of this specification标准充电：在环境温度20℃±5℃的条件下，以0.2C5A充电，当电池端电压达到充电截止电压时，改为恒压充电，直到充电电流小于或等于0.01C5A后停止充电。
standard Charge: Charge with current0.2C5A to limit charge voltage under the condition of 20℃±5℃ surrounding t emperature, then change to charge with constant voltage till the current less than or equal to 0.01 C5A.4.1电化学性能Electrical Characteristic序号NO.项目Item 标准Standard 测试方法Test Method1常温放电性能DischargeCharacteristics0.5C5A ≥2h在1标准大气压，环境温度20℃±5℃，相对湿度为45％～75％的条件下，电池标准充电后（以下若没有特别说明，均在此条件下放置，皆按此充电方式），搁置30min，以0.5C5A进行放电至终止电压，循环三次，当有一次达到标准，即达到标准要求（下同）。
18650锂电池组技术规格书
YAGEO
6
R9,R10
Resistor
SMD 5.1KΩ±5%
0603
2
YAGEO
7
R7
合金电阻
P=1W
SMD 10mΩ±5%
2512
1
YAGEO
8
R6
Resistor
SMD 51Ω±5%
0603
1
YAGEO
9
C1,C2,C3
Capacitor
SMD 0.22μF
0603
3
YAGEO
10
C5,C6
断开短路电路
内阻
RSS
主回路通态电阻
RSS≤65mΩ
消耗电流
IDD
工作时电路内部消耗
30.0μA Max
零 V 充电
OV
向0 V电池充电（电芯电压最小1.7V）
允许
4 Parts list主要元件清单
NO.
元件编号
元件名称
元件规格
封装式
数量
厂商/备注
1
U1
Batteryprotection IC
S8254AANFT-TB-G
TSSOP-16
1
SEIKO
2
Q3,Q4
Silicon MOSFET
AO4407
SO-8
2
AOS
3
R1,R2,R3
Resistor
SMD 510Ω±5%
0603
3
YAGEO
4
R4,R5,R11
Resistor
SMD 10KΩ±5%
0603
3
YAGEO
5
R8
Resistor
wsriors 18650 2000MAH 3.7V Lithium-ion 电池说明书
03-Jan-202003-Jan-2020 NO:20202011Product Name wsrriors 18650 2000MAH 3.7V Lithium-ion battery warriors 18650 2000MAH 3.7V Lithium-ion battery SAFETY DATA SHEETHCS-2012 APPENDIX D TO §1910.1200Version 1Issue Date Product Name Revision date _____________________________________________________________________________________________ _____________________________________________________________________________________________1. IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKINGProduct identifierOther means of identification Product Code Voltage: 3.7VAmpere hour: 100MAHRecommended use of the chemical and restrictions on use Recommended Use Power supply Uses advised against No information availableDetails of the supplier of the safety data sheet Supplier Suzhou Xinlvzhou Electronics Co., Ltd Address No. 158 Sanji Road, Xiangcheng District, Suzhou, Jiangsu Postal Code 215131 Phone +86-512-68702665 FAX +86-512-68669435 E-mail ***********************.cnEmergency telephone number +86-512-687026652. HAZARDS IDENTIFICATIONGHS Classification Not classifiedLabel elementsSymbols/Pictograms None Signal word None Hazard Statements Not classified Precautionary Statements Prevention None Response None Storage None Disposal NoneHazards not otherwise classified (HNOC)Batteries may vent, ignite and produce sparks when subjected to high temperature, when damaged or abused(e.g., mechanical damage); may burn rapidly with flare-burning effect; may ignite other batteries in clothes proximity.This product should not present a health hazard when used under reasonable conditions. If contact with the internal components of the battery may be irritating to skin, eyes and mucous membranes. Fire will produce irritating, corrosive and/or toxic gases. Burning batteries may produce toxic hydrogen fluoride gas. Fumes may cause dizziness or suffocation.If the battery is discarded into the environment, the harmful contents inside may be dangerous.Unknown acute toxicity No information available3. COMPOSITION/INFORMATION ON INGREDIENTSChemical nature MixtureChemical Name CAS No Weight-% Lithium Cobalt Oxide (CoLiO2) 12190-79-3 40Aluminum foil 7429-90-5 29Carbon black 1333-86-4 21Copper 7440-50-8 8 Phosphate(1-), hexafluoro-, lithium 21324-40-3 24. FIRST AID MEASURESDescription of first aid measuresGeneral advice No effect under routine handling and use. If exposure to internal materials withincells due to damaged outer metal casing, the following actions are recommended.Inhalation If inhaled, remove from exposure and move to fresh air immediately. Rinse mouthand nose with water. Get medical aid immediately. DO NOT use mouth-to-mouthresuscitation. If breathing has ceased apply artificial respiration using oxygen anda suitable mechanical device.Skin Contact In case of contact, immediately flush skin with copious amounts of water for atleast 15 minutes while removing contaminated clothing and shoes. Wash clothingand shoes before reuse. Get medical aid.Eye contact Rinse immediately with plenty of water during at least 15-30 minutes, occasionallylifting the upper and lower eyelids. Check for and remove any contact lenses ifeasily possible. DO NOT rubbing eyes with hand. Get medical aid immediately.Ingestion Do not induce vomiting. If the injured is fully conscious: wash mouth out withwater, then give 2-4 cupfuls of milk or water. Never give anything by mouth to anunconscious person. Get medical aid immediately.Most important symptoms and effects, both acute and delayedSee Section 11 for more information.Indication of any immediate medical attention and special treatment neededTreat symptomatically and supportively.5. FIRE-FIGHTING MEASURESExtinguishing mediaSuitable extinguishing media Use extinguishing measures that are appropriate to local circumstances and thesurrounding environment.Unsuitable extinguishing media No information available.Specific hazards arising from the chemicalToxic vapor may release in case of fire. Thermal shock may cause battery case to crack open. Containers may explode when heated. Firefighting water runoff and dilution water may be toxic and corrosive and may cause adverse environmental impacts. On some bad using conditions (e.g., mechanical damage, external short circuit.) and in case of a bad functioning, some electrolyte can be removed from the cell by the security vent. Exposure to the ingredients contained within the battery pack could be harmful under some circumstances.Protective equipment and precautions for firefightersAs in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear. Evacuate personnel to safe areas.6. ACCIDENTAL RELEASE MEASURESPersonal precautions, protective equipment and emergency procedures_____________________________________________________________________________________________Toxic vapor may release in case of fire. Thermal shock may cause battery case to crack open. Containers may explode when heated. Firefighting water runoff and dilution water may be toxic and corrosive and may cause adverse environmental impacts. On some bad using conditions (e.g., mechanical damage, external short circuit.) and in case of a bad functioning, some electrolyte can be removed from the cell by the security vent. Exposure to the ingredients contained within the battery pack could be harmful under some circumstances.Methods and material for containment and cleaning upAvoid dispersal of spilled material and runoff and contact with soil, water ways, drains and sewers.Remove all sources of ignition or heat. Stop leak if safe to do so. Move containers from spill area. Carefully collect undamaged batteries in a clean, dry and appropriate container for reuse or disposal. If electrolyte leaks or spills, collect all released material in an appropriate container before proper disposal.7. HANDLING AND STORAGEPrecautions for safe handlingThis product should be stored, handled and used in accordance with good industrial hygiene practices and in conformity with any legal regulation. Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period.Conditions for safe storage, including any incompatibilitiesStore in a cool and dry area, but prevent condensation on cell or battery terminals. High temperature may damage the performance of the battery. Protect from physical damage and short circuits. To avoid risk of fire or explosion, keep sparks and other sources of ignition away from the battery. Do not allow metal objects to simultaneously contact both positive and negative terminal of batteries. Do not stack battery directly on another battery. Do not store batteries on electrically conductive surfaces.8. EXPOSURE CONTROLS/PERSONAL PROTECTIONControl parametersChemical Name ACGIH TLV OSHA PEL NIOSH IDLH Denmark European Union Lithium Cobalt Oxide(CoLiO2) (CAS #:12190-79-3)TWA: 0.02 mg/m3Co - - TWA: 0.01 mg/m3-Aluminum foil (CAS #: 7429-90-5)TWA: 1 mg/m3respirable fractionTWA: 15 mg/m3 totaldustTWA: 5 mg/m3respirable fraction(vacated) TWA: 15mg/m3 total dust(vacated) TWA: 5mg/m3respirablefraction (vacated)TWA: 5 mg/m3 AlAluminumTWA: 10 mg/m3total dustTWA: 5 mg/m3respirable dust TWA: 5mg/m3AlTWA: 5 mg/m3TWA: 2 mg/m3-Carbon black (CAS #: 1333-86-4)TWA: 3 mg/m3inhalable fraction- IDLH: 1750 mg/m3TWA: 3.5 mg/m3TWA: 0.1 mg/m3Carbon black inpresence of Polycyclicaromatic hydrocarbonsPAHTWA: 3.5 mg/m3-Copper (CAS #: 7440-50-8) TWA: 0.2 mg/m3fume TWA: 1 mg/m3Cu dust and mist - IDLH: 100 mg/m3dust, fume and mistIDLH: 100 mg/m3 Cudust and mistTWA: 1 mg/m3 dustand mistTWA: 0.1 mg/m3fume TWA: 1 mg/m3Cu dust and mistTWA: 1.0 mg/m3TWA: 0.1 mg/m3-Phosphate(1-), hexafluoro-,lithium (CAS #: 21324-40-3)TWA: 2.5 mg/m3F - - TWA: 2.5 mg/m3-_____________________________________________________________________________________________Chemical Name Latvia France Finland Germany Italy Lithium Cobalt Oxide(CoLiO2) (CAS #:12190-79-3)- TWA: 0.02 mg/m3Skin -Aluminum foil (CAS #: 7429-90-5) TWA: 2 mg/m3TWA: 10 mg/m3TWA: 5 mg/m3TWA: 1.5 mg/m3 TWA:4mg/m3TWA: 1.5 mg/m3-Carbon black (CAS #: 1333-86-4) TWA: 3.5 mg/m3 TWA:3.5mg/m3STEL: 7 mg/m3Skin -Copper (CAS #: 7440-50-8) TWA: 0.5 mg/m3STEL: 1 mg/m3TWA: 0.2 mg/m3TWA: 1 mg/m3STEL: 2 mg/m3TWA: 1 mg/m3TWA: 0.1 mg/m3TWA: 0.01 mg/m3Ceiling / Peak: 0.02mg/m3 Ceiling / Peak:0.2 mg/m3-Phosphate(1-), hexafluoro-, lithium (CAS #: 21324-40-3) - - TWA: 1 mg/m3Skin-Chemical Name Poland Portugal Spain Switzerland NetherlandsAluminum foil (CAS #: 7429-90-5) TWA: 2.5 mg/m3TWA: 1.2 mg/m3TWA: 10 mg/m3 TWA:5 mg/m3TWA: 10 mg/m3 TWA:5 mg/m3TWA: 3 mg/m3-Copper (CAS #: 7440-50-8) - - - - TWA: 0.1 mg/m3 Chemical Name Norway United Kingdom Australia Austria BelgiumLithium Cobalt Oxide (CoLiO2) (CAS #:12190-79-3) TWA: 0.02 mg/m3STEL: 0.02 mg/m3- - Skin -Aluminum foil (CAS #: 7429-90-5) TWA: 5 mg/m3STEL: 5 mg/m3STEL: 30 mg/m3STEL: 12 mg/m3TWA: 10 mg/m3TWA: 4 mg/m310 mg/m35 mg/m3STEL 20 mg/m3TWA: 10 mg/m3-Carbon black (CAS #: 1333-86-4) TWA: 3.5 mg/m3STEL: 3.5 mg/m3- 3 mg/m3- -Copper (CAS #: 7440-50-8) TWA: 0.1 mg/m3TWA: 1 mg/m3STEL: 0.1 mg/m3STEL: 1 mg/m3- 1 mg/m30.2 mg/m3STEL 4 mg/m3STEL 0.4 mg/m3TWA: 1 mg/m3TWA: 0.1 mg/m3-Phosphate(1-), hexafluoro-,lithium (CAS #: 21324-40-3)- - 2.5 mg/m3- -Appropriate engineering controlsGeneral room ventilation is sufficient during normal use and handing. Do not install these batteries in sealed, unventilated areas. Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower.Remove jewelry, rings, watches and any other metallic objects while working on battery. All tools should insulate to avoid the possibility of shorting connections. DO NOT lay tools on top of the battery. The work area should be equipped with the corresponding species and quantity of fire equipment and leakage emergency equipment. Individual protection measures, such as personal protective equipmentRespiratory protection If exposure limits are exceeded or irritation is experienced, NIOSH/MSHAapproved respiratory protection should be worn. Positive-pressure supplied airrespirators may be required for high airborne contaminant concentrations.Respiratory protection must be provided in accordance with current localregulations.Hand Protection Under normal condition of use and handling no special protection is required forsealed battery. In the event of battery case breakage, should be wear appropriatesafety gloves.Eye/face protection Under normal condition of use and handling no special protection is required forsealed battery. Use appropriate safety glasses when there is the risk of splash.Skin and body protection Under normal condition of use and handling no special protection is required forsealed battery. It is recommended to wear appropriate protective clothing whenthe battery case is broken.9. PHYSICAL AND CHEMICAL PROPERTIESInformation on basic physical and chemical properties_____________________________________________________________________________________________Appearance SolidColor Black Array Odor OdorlessOdor Threshold Not determinedpH Not determinedMelting point/freezing point Not determinedBoiling point / boiling range Not determinedFlash point Not determinedEvaporation rate Not determinedFlammability (solid) Not flammableFlammability Limit in Air Not applicableVapor Pressure Not determinedVapor density Not applicableDensity Not determinedRelative density Not determinedBulk density Not determinedSpecific gravity Not determinedWater solubility Insoluble in waterPartition coefficient (LogPow) Not determinedAutoignition temperature Not applicableDecomposition temperature Not determinedKinematic viscosity Not determinedDynamic viscosity Not determinedExplosive properties Not an explosiveOxidizing properties Not determinedOther informationNo information available10. STABILITY AND REACTIVITYReactivityStable under recommended storage and handling conditions (see SECTION 7, handling and storage).Chemical stabilityStable under normal conditions.Possibility of Hazardous ReactionsWhen a battery cell is exposed to an external short-circuit, crushed, modification, high temperature, open flames, it will be the cause of heat generation and ignition.Conditions to avoidExposed to an external short-circuit, crushed, modification, high temperature, open flames, incompatible materials, direct sunlight and high humidity.Incompatible materialsConductive materials, water, seawater, strong oxidants, strong acid, strong bases, etc.Hazardous Decomposition ProductsIn case of a fire or high temperature, metal oxides and irritating/harmful fumes/smoke may be generated.11. TOXICOLOGICAL INFORMATIONInformation on likely routes of exposureInhalation No effect under routine handling and use for sealed battery. If battery is broken,inhale fume and dust may cause upper respiratory irritation and lung irritation._____________________________________________________________________________________________Eye contact No effect under routine handling and use for sealed battery. Exposure to theelectrolyte contained inside the battery may result in irritation.Skin Contact No effect under routine handling and use for sealed battery. Exposure to theelectrolyte contained inside the battery may result in chemical burns.Ingestion No effect under routine handling and use for sealed battery. Harmful if swallowedthe electrolyte contained inside the battery. Exposure to the electrolyte containedinside the battery may cause irritation to mouth, esophagus and gastrointestinalsystem.Information on toxicological effectsAcute toxicityChemical Name Oral LD50 Dermal LD50 Inhalation LC50 Carbon black (CAS #:1333-86-4)> 8000 mg/kg (rat) > 3000 mg/kg (Rabbit) -Copper (CAS #: 7440-50-8) > 2500 mg/kg bw(rat) > 2000 mg/kg bw(rat) =1.03 mg/L/4 h(rat)Skin corrosion/irritationNo effect under routine handling and use for sealed battery. Exposure to the electrolyte contained inside the battery may result in chemical burns.Serious eye damage/eye irritationNo effect under routine handling and use for sealed battery. Exposure to the electrolyte contained inside the battery may result in irritation.SensitizationNo sensitization responses were observed.Germ cell mutagenicityNo information availableCarcinogenicityChemical Name ACGIH IARC NTP OSHA Lithium Cobalt Oxide(CoLiO2) (CAS #:12190-79-3)A3 Group 2B - -Carbon black (CAS #:1333-86-4)A3 Group 2B - -Reproductive toxicityNo information availableSTOT - single exposureNo information availableSTOT - repeated exposureNo information availableAspiration hazardNo information available12. ECOLOGICAL INFORMATIONEcotoxicityChemical Name Algae/aquatic plants EC50 Fish LC50 Crustacea EC50Lithium Cobalt Oxide (CoLiO2) (CAS #: 12190-79-3) - 275 mg/L/96h(Fundulusheteroclitus)-_____________________________________________________________________________________________2016 Edition, including the passing of the UN38.3 test ID:1118010201.965 of 61th DGR Manual of IATA( 2019 edition )or special provision188 of IMDG CODE (Amdt37-14)_____________________________________________________________________________________________Copper (CAS #: 7440-50-8)0.031 - 0.054 mg/L/96h Pseudokirchneriella subcapitata static 0.0426 - 0.0535 mg/L/72h Pseudokirchneriella subcapitata static 1.25: 96 h Lepomis macrochirus mg/L LC50 static 0.3: 96 hCyprinus carpio mg/L LC50semi-static 0.8: 96 h Cyprinus carpio mg/L LC50 static 0.112:96 h Poecilia reticulata mg/LLC50 flow-through 0.0068 - 0.0156: 96 h Pimephales promelas mg/L LC50 0.3: 96 h Pimephales promelas mg/L LC50 static 0.2: 96 h Pimephales promelas mg/L LC50 flow-through 0.052: 96 h Oncorhynchus mykiss mg/LLC50 flow-through-Persistence and degradability No information availableBioaccumulative potential No information availableMobility in soilNo information availableOther adverse effects No information available13. DISPOSAL CONSIDERATIONSWaste treatment methods Disposal of wastesDisposal should be in accordance with applicable regional, national and local laws and regulationsContaminated packaging Dispose of in accordance with federal, state and local regulationsChemical NameCalifornia Hazardous Waste StatusLithium Cobalt Oxide (CoLiO2)12190-79-3 ToxicAluminum foil 7429-90-5 Ignitable powderCopper 7440-50-8Toxic14. TRANSPORT INFORMATION15. REGULATORY INFORMATIONInternational InventoriesLabel for conveyance: Lithium Battery Label, Class 9UN Number: UN3480Packaging Group: N/A EmS No: 4.1-06Marine pollutantÿNo Proper Shipping name: Lithium ion batteries Hazard Classification: The goods shall be complied with the requirements of Section IBof Packing InstructionsRevision date 03-Jan-2020 Issue Date 03-Jan-2020_____________________________________________________________________________________________Component AICS DSL/NDSL EINECS/ELINCSENCS IECSC KECL PICCS TSCA Lithium Cobalt Oxide (CoLiO2) 12190-79-3 ( 40% )X X XX X X - X Aluminum foil 7429-90-5 ( 29% ) X X X Expect X X X X Carbon black 1333-86-4 ( 21% )X X X X X X X X Copper7440-50-8 ( 8% ) X X X Expect X X X X Phosphate(1-), hexafluoro-, lithium 21324-40-3 ( 2% )XXXXXXXX"-" Not Listed"X" ListedUS Federal Regulations SARA 313Chemical NameSARA 313 - Threshold Values %Aluminum foil - 7429-90-51.0SARA 311/312 Hazard Categories Not applicableCWA (Clean Water Act)Chemical Name CWA - ReportableQuantitiesCWA - Toxic PollutantsCWA - Priority PollutantsCWA - Hazardous SubstancesCopper 7440-50-8-XX-CERCLA Not applicableUS State RegulationsCalifornia Proposition 65Chemical Name California Proposition 65Carbon black - 1333-86-4CarcinogenU.S. State Right-to-Know RegulationsChemical NameNew JerseyMassachusettsPennsylvaniaLithium Cobalt Oxide (CoLiO2)12190-79-3 X--Aluminum foil 7429-90-5 X X X Carbon black 1333-86-4 X X - Copper 7440-50-8X X - Phosphate(1-), hexafluoro-, lithium21324-40-3X--16. OTHER INFORMATIONRevision Note Revision Note Not applicableKey or legend to abbreviations and acronyms used in the safety data sheet TWA - TWA (time-weighted average)STEL - STEL (Short Term Exposure Limit)Ceiling - Maximum limit valueTSCA - United States Toxic Substances Control Act Section 8(b) InventoryDSL/NDSL - Canadian Domestic Substances List/Non-Domestic Substances ListEINECS/ELINCS - European Inventory of Existing Chemical Substances/European List of Notified Chemical Substances ENCS - Japan Existing and New Chemical SubstancesIECSC - China Inventory of Existing Chemical SubstancesKECL - Korean Existing and Evaluated Chemical SubstancesPICCS - Philippines Inventory of Chemicals and Chemical SubstancesAICS - Australian Inventory of Chemical SubstancesDisclaimerThe information provided in this Material Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text.-------- End of Safety Data Sheet --------_____________________________________________________________________________________________。
INR18650HE-2000mAh-产品规格书Ver1 SPEC-00 3(1)
龙能科技锂离子电池
产品规格书
Product Specifications
型号: INR18650HE-2000mAh
制定
审核
批准
龙能科技（苏州）有限公司
地址：苏州工业园区东旺路 8 号
电话：（0512） 6281 8888 传真：（0512）62622615 邮编：215000
5.3 标准充电 …………………………………………………………………………………… 5
5.4 搁置时间 …………………………………………………………………………………… 5
初始性能测试 …………………………………………………………
5
5.5
…………………
5.6 电性能测试 ………………………………………………………………………………… 6
5.7 机械特性
…………………………………………………………………………… 7
5.8 安全性能
…………………………………………………………………………… 7
6 电池使用指南 ……………………………………………………………………………………… 8
7 保质期 ……………………………………………………………………………………………… 9
…………………………
9
8 电池出厂时状况
………………………………………………………
9 产品规格书的修订 ………………………………………………………………………………… 9
18650HE-2000 外形尺 10
寸图
………………………………………………………………… 10
规格书编号 IE/WI-B-RD-C003 版本 1.0 规格书页码
ICR18650NH锂电池电芯规格书
7.SafetyCharacteristics
Item
Test Method
Performances
Short Circuit
Over charge
Thebattery cellistobeshort-circuitedbyconnecting thepositiveand negativeterminals ofthebatterywith anexternalloadoflessthan100mΩuntilthesurface temperaturedecrease 10degree from the highest point.
Thebattery cellshallnot rupture, smoke, catch fire, vent or leak.The voltage is no less than .
Thebattery cellshallnot rupture, smoke, catch fire, vent or leak.
voltageofwhiletaperingthechargecurrenttoless than or equalto C. Charging time ishours inall.
①Within1hourafterfullycharged,dischargedat
continuouslydown to .
Page
4/11
Over discharge
Crush
Impact
Heating
Aftercompletecharge,thebattery cellwillbe discharged toend voltage.Then connectwith external loadof30Ωdischarge for 24hrs.
18650-2000电芯规格书
18650-2000电芯规格书德赛能源科技有限公司承认书文件名称：18650圆柱型锂离子电芯文件编号： D.DD.S £1-138送交确认版别：文件编号 D.DD.S-01 -38受控号：日期2004/10/17批准:审核:承办:此标准文件仅供贵司确认之用。
当贵司确认后，将根据贵司反馈意见发放正式受控文件。
我司规格数据表型密圭寸圆柱可充锂离子电池ICR18650186503.6V45cJ20 GmAh ---------O0mAh7充电 ---------- 4.200压± 0.049V最~~大~~持~~续~~充电电~~流 ----------------------------- 1500mA 最大持续放电电流---------------------------- 3000mA 尺寸（包括热缩 外套）直径， d 18.0 ± 0.2mm 高度， h65.0 ±0.5mm ------容量（20 °C, 0.2 C 5 to 2.75V ）最小容量20mA快速充电 1500mA 至4.2V,4.2V 恒压至电流小于 20mA使用环境（建议） 储存--- 温 度（15-35 C ）相对湿度（45-75%）大气压力（86-106kPa ）放电-20-60 C标准充电0-45 C完全充电后测量）-------- 小于80nn Q充电条件（20 C5C )标准充电------ 1000mA至4.2V,4.2V 恒压至电流小于2000mAh内阻(20°C 5°C,相对湿度<93% 标准测试环境 温20°C± 5°C20%如有更改，以新版本为准，不另行通知。
1.性能86-106kPa非另外要求）湿45度版别： 文件编号D.DD.S-01 -38受控号：日期 2004/10/17放电容量:- >60%C 5的.囉24辩、万Che 恒4电龍2AW 充「c m巧标跟亡.22〔疑H^o压量度应M 谷池2池电・境电處、田1^:(^4保护功能当锂离子可充电池在高于允许的电压或电流的情况下工作，电解液可能会分解，这样会影响到电池的安全性能。
2000mAh锂电池电池技术规格书
技术规格书型号：2000mAh编制：审核：批准：目录 Contents1. 范围 (3)2. 产品描述与型号 (3)3. 定义 (3)4. 产品规格 (3)5. 外形尺寸 (4)6. 外观 (4)7. 性能规格 (5)7.1 标准测试条件 (5)7.2 电性能 (5)7.3 环境适应性能 (6)7.4 安全性能 (6)7.5 机械性能 (6)8. 包装 (7)9. 运输 (7)8. 长期存储 (7)11. 保质期 (7)12. 产品责任 (7)电池组基本信息1.适用范围本产品规格书描述的是可充电锂离子电芯，包括产品规格信息、各种性能测试条件、产品责任及注意事项。
2.产品描述与型号2.1 产品描述: 电芯(可充电锂离子电池)2.2 型号 Model: 2000mAh3.定义3.1 标准模式充电标准模式充电的定义:在25±2℃下, 将电芯以0.5C电流恒流充电到4.2V, 然后转为在4.2V下恒压充电至截至电流0.01C。
3.2 标准模式放电标准模式放电的定义: 在25±2℃下, 将满电态电芯以0.2C电流恒流放电到3.0V。
4.产品规格工作温度和湿度范围充电 0 ~ 50℃60±25％R.H. 低温充电效率会下降，会影响电池使用寿命放电 -30 ~ 50℃60±25％R.H.电芯重量≤44.0±1.0g电芯尺寸高度≤65.50mm ；直径≤18.45 mm长时间存储温度-20~25℃60±25％R.H.不可超过半年，达到半年须充电一次带保护板电池3个月充电一次5.外形尺寸见附图图1. 外形尺寸6.主要零部件列表带帽PTC参数表7. 标准测试条件无其它指定时，按GB/18287-2013标准测试条件。
本规格书中所有的测试均在25±5℃（温度）≤75％RH（湿度）下进行；6.外观应没有如深度划痕、裂缝、生锈、斑点或漏液等影响电芯商业价值的外观瑕疵。
18650（3600mah）规格书（标准书）
18650（3600mah）规格书（标准书）文件名称产品型号修改记录产品型号目录1 适用范围 (4)2 引用标准 (4)3 定义........................................ .. (4)3.1 手机用电池battery for cellular phone ..... . (4) 3.2 充电限制电压 limited charge voltage ............... .. (4)3.3 额定容量 rated capacity ........................... .. (4)3.4 标称电压 nominal voltage (4)3.5 终止电压 cut-off voltage (4)4 技术参数 (4)4.1 电芯参数表 (4)4.2 主要参数表 (5)4.3 保护板参数表 (5)5 要求 (5)5.1 测试条件 (5)5.2 测量仪表与设备要求 (6)5.3 外观 (6)5.4 充电制式 (6)5.5 20℃放电性能 (6)5.6 高温性能 (6)5.7 低温性能 (6)5.8 荷电保持能力 (6)5.9 循环寿命 (7)5.10 环境适应性 (7)5.11 安全保护性能 (7)5.12 电池完全完全充电后内阻 (8)6 运输、贮存 (8)7 安全规程及使用说明 (8)8 特殊要求 (8)9 PCB原理图，电芯基本特性及外形图 (9)10 电芯充放电曲线图11 成品电池尺寸图产品型号1 适用范围本规格书适用于可充电锂离子电池产品的定义、要求、测试方法、质量评定程序及标志、包装、运输、贮存。
用户请务必严格按照规格书中的测试或使用方法进行测试或使用，如对表中的测试项目或测试方法有异议，请与供应方协商解决2 引用标准下列标准所包含的条文，通过在本规范中引用而构成为本规范的条文。
GB/T 2828-1987 逐批检查计数抽样程序及抽样表（适用于连续批的检查）GB/T 2829-1987 周期检查计数抽样程序及抽样表（适用于生产过程稳定性的检查）GB/T 2900.11-1988 蓄电池名词术语3 定义本规范采用GB/T 2900.11 中规定的术语和下列定义。
18650锂电池组技术规格书
Resistor
SMD 10KΩ±5%
0603
3
YAGEO
5
R8
Resistor
SMD 1MΩ±5%
0603
1
YAGEO
6
R9,R10
Resistor
SMD 5.1KΩ±5%
0603
2
YAGEO
7
R7
合金电阻
P=1W
SMD 10mΩ±5%
2512
1
YAGEO
8
R6
Resistor
SMD 51Ω±5%
过放电解除电压（备有休眠的IC，需
VDD-VM电压差在1.3V以上才可以恢复）
3.0±0.1V
过流保护
VDET3
过电流检测电压
0.1±0.025V
VDET3
过充电流检测电压
/
IDP
过电流保护电流
8.0～11.0A
IDP
过充电流保护电流
/
tVDET3
检测延迟时间
10.0±5.0mS
保护解除条件
Cut load
全新进口索尼18650/2600MAH电芯
组合方式
三串六并
电池容量
15.6AH
电池组平均电压
11.1V
电池组输出电压范围
9V→12.6V
电池组充电电压范围
12.6V→12.8V
外形尺寸
约35*185*68mm
要求电池组输出功率
25W
电池组标准充电电流
0.2-0.5C
锂电池保护功能部分
电池组具有充放电电流.电压保护电路，短路保护
0603
1
YAGEO
三星18650-2.0规格书
SPECIFICATION OF PRODUCTfor Lithium-ion rechargeable cellModel name : INR18650-20R MFeb. 4, 2014Samsung SDI Co., Ltd.Cell Business DivisionRevision history1. ScopeThis product specification has been prepared to specify the rechargeable lithium-ion cell ('cell') to be supplied to the customer by Samsung SDI Co., Ltd.2. Description and model2.1 Description lithium-ion rechargeable cell2.2 Model name INR18650-20R M3. Nominal specificationsthe capacity recovery rate is more than 90% of 10A discharge capacity100% is 1,950mAh at 25℃with SOC 100% after formation.4. Outline dimensionsSee the attachment (Fig. 1)Fig.1. Outline dimensions of INR18650-20RUnit : mm With tube18.33±0.0764.85± 0.155. AppearanceThere shall be no such defects as scratch, rust, discoloration, leakage whichmay adversely affect commercial value of the cell.6. Standard test conditions6.1 Environmental conditionsUnless otherwise specified, all tests stated in this specification are conducted attemperature 25±5℃and humidity 65±20%.6.2 Measuring equipment(1) Amp-meter and volt-meterThe amp-meter and volt-meter should have an accuracy of the grade 0.5mA andmV or higher.(2) Slide caliperThe slide caliper should have 0.01 mm scale.(3) Impedance meterThe impedance meter with AC 1kHz should be used.7. Characteristics7.1 Standard chargeThis "Standard charge" means charging the cell CCCV with charge current 0.5CmA(1,000mA), constant voltage 4.2V and 100mA cut-off in CV mode at 25℃for capacity..7.2 Rapid chargeRapid charge means charging the cell CCCV with charge current 4A and 100mA cut-off at 25℃7.3 Nominal discharge capacityThe standard discharge capacity is the initial discharge capacity of the cell, which ismeasured with discharge current of 400mA(0.2C) with 2.5V cut-off at 25℃within 1hour after the standard charge.Nominal discharge capacity ≥2,000mAhWhich complying to the minimum capacity of IEC61960 standard.7.4 Standard rated discharge capacityThe standard rated discharge is the discharge capacity of the cell, which is measured with discharge current of 10A with 2.5V cut-off at 25℃within 1hour after the standard charge.Standard rated discharge capacity ≥1,950mAh7.5 Initial internal impedanceInitial internal impedance measured at AC 1kHz after standard chargeInitial internal impedance ≤18mΩ7.6 Temperature dependence of discharge capacityCapacity comparison at each temperature, measured with dischargethe interval for temperature change is 3 hours.Percentage index of the discharge at 25℃at 10A (=1,950mAh) is 100%.7.7 Temperature dependence of charge capacityCapacity comparison at each temperature, measured with discharge constant current 10A and 2.5V cut-off after the standard charge is as follows.the interval for temperature change is 3 hours.Percentage index of the discharge at 25℃at 10A (=1,950mAh) is 100%.7.8 Charge rate capabilitiesDischarge capacity is measured with constant current 10A and 2.5V cut-offafter the cell is charged with 4.2V as follows..7.9 Discharge rate capabilitiesDischarge capacity is measured with the various currents in under table and 2.5Vcut-off after the standard charge.Percentage index of the discharge at 25℃at 10A (=1,950mAh) is 100%.7.10 Cycle lifeWith standard charge and maximum continuous discharge.Capacity after 250cycles,Capacity ≥1,200mAh (60% of the nominal capacity at 25℃)7.11 Storage characteristicsStandard rated discharge capacity after storage for 1 month at 60℃from the standard charged state is ≥90% of the initial 10A discharge capacity at 25℃7.12 Status of the cell as of ex-factoryThe cell should be shipped in 50 ± 5% charged state. In this case, OCV is from 3.60V to 3.80V.8. Mechanical Characteristics8.1 Drop testTest method: Cell(as of shipment or full charged) drop onto the oak-board(thickness: ≥30mm) from 1.0m height at a random direction 6 times.Criteria: No leakage, Voltage decrease≦0.025V, AC IR increase ≦1.0mΩ8.2 Vibration testTest method: As to the UN transportation regulation(UN38.3), for each axis (X and Y axis with cylindrical cells) 7Hz→200Hz→7Hz for 15min, repetition 12 times totally3hours, the acceleration 1g during 7 to 18Hz and 8g (amplitude 1.6mm) up to 200Hz.Criteria: No leakage, with less than 10mV of OCV drop9. Safety9.1 Overcharge testTest method: To charge with 20A-20V at 25℃for 2hr.Criteria: No fire, and no explosion.9.2 External short-circuit testTest method: To short-circuit the standard charged cell (or 50% discharged cell)by connecting positive and negative terminal by 50mΩwire for 10min.Criteria: No fire, and no explosion.9.3 Reverse charge testTest method: To charge the standard charged cell with charge current 10ABy 0V for 2.5 hours.Criteria: No fire, and no explosion.9.4 Heating testTest method: To heat up the standard charged cell at heating rate 5℃per minute up to 150℃and keep the cell in oven for 10 minutes.Criteria: No fire, and no explosion.10. WarrantySamsung SDI will be responsible for replacing the cell against defects or poor workmanship for 15months from the date of shipping. Any other problem caused by malfunction of the equipment or mix-use of the cell is not under this warranty.The warranty set forth in proper using and handling conditions described above and excludes in the case of a defect which is not related to manufacturing of the cell.11. Others11.1 Storage for a long timeIf the cell is kept for a long time (3 months or more), It is strongly recommendedthat the cell is preserved at dry and low-temperature.11.2 OthersAny matters that specifications do not have, should be conferred with between theboth parties.12. PackagingSee Fig.2, Package DrawingFig 2. Package DrawingProper use and handling of lithium ion cellsSee before using lithium-ion cellSupplied bySamsung SDI Co., Ltd.1. GeneralThis document has been prepared to describe the appropriate cautions and prohibitions, which the customer should take or employ when the customer usesand handles the lithium ion cell to be manufactured and supplied by Samsung SDI Co., Ltd., in order to obtain optimal performance and safety.2. Charging2.1 Charging currentCharging current shall be less than maximum charge current specified in the productspecification.2.2 Charging voltageCharging shall be done by voltage less than that specified in the product specification.2.3 Charging timeContinuous charging under specified voltage does not cause any loss of performance characteristics. However, the charge timer is recommended to be installed from asafety consideration, which shuts off further charging at time specified in the productspecification.2.4 Charging temperatureThe cell shall be charged within a range of specified temperatures in the specification.2.5 Reverse chargingThe cell shall be connected, confirming that its poles are correctly aligned.Inverse charging shall be strictly prohibited. If the cell is connected improperly, it may be damaged.3. Discharging3.1 Discharging3.1.1 The cell shall be discharged continuously at less than maximum discharge currentspecified in the product specification. In case of the higher discharge currentshould be set, it shall be discussed together with SDI.3.2 Discharging temperature3.2.1 The cell shall be discharged within a range of temperatures specified inthe product specification.3.2.2 Otherwise, it may cause loss of performance characteristics.3.3 Over-discharging3.3.1 The system should equip with a device to prevent further dischargingexceeding discharging cut-off voltage specified in the product specification.3.3.2 Over-discharging may cause loss of performance characteristics of battery.3.3.3 Over-discharging may occur by self-discharge if the battery is left fora very long time without any use.3.3.4 The charger should equip with a device to detect voltage of cell block and todetermine recharging procedures.4. Storage4.1 Storage conditions4.1.1 The cell should be stored within a range of temperatures specifiedin the product specification.4.1.2 Otherwise, it may cause loss of performance characteristics, leakage and/or rust.4.2 Long-term storage4.2.1 The cell should be used within a short period after charging becauselong-term storage may cause loss of capacity by self-discharging.4.2.2. If long-term storage is necessary, the cell should be stored at lowervoltage within a range specified in the product specification, becausestorage with higher voltage may cause more loss of performance characteristics.5. Cycle life5.1 Cycle life performance5.1.1 The cell can be charged/discharged repeatedly up to times specified inthe product specification with a certain level of capacity specified in theproduct specification.5.1.2 Cycle life may be determined by conditions of charging, discharging,operating temperature and/or storage.6. Design of system6.1 Connection between the cell and the battery6.1.1 The cell should not be soldered directly with other cells. Namely, the cellshould be welded with leads on its terminal and then be soldered withwire or leads to solder.6.1.2 Otherwise, it may cause damage of component, such as separator andinsulator, by heat generation.6.2 Positioning the battery in the system6.2.1 The battery should be positioned as possible as far from heat sourcesand high temperature components.6.2.2 Otherwise, it may cause loss of characteristics.6.2.3 The recommended spacing between the cells is more than 1mm.6.3 Mechanical shock protection of the battery6.3.1 The battery should be equipped with appropriate shock absorbers in the packin order to minimize shock, which can damage the cells.6.3.2 Otherwise, it may cause shape distortion, leakage, heat generationand/or rupture and/or open circuit.6.4 Short-circuit protection of the cell6.4.1 The cell equips with an insulating sleeve to protect short-circuit whichmay occur during transportation, battery assembly and /or system operation.6.4.2 If the cell sleeve is damaged by some cause such as outside impact,it may cause short-circuit with some wiring inside the battery.6.5 Connection between the battery and charger/system6.5.1 The battery should be designed to be connected only to the specifiedcharger and system.6.5.2 A reverse connection of the battery, even in the specified system,should be avoided by employing special battery design such asa special terminals.6.6 Pack design6.6.1 The current consumption of the battery pack should be under 10uAat sleep mode.6.6.2 Cell voltage monitoring system.The system (charger or pack) should be equipped with a device to monitor eachvoltage of cell block to avoid cell imbalance which can cause damage to the cells.6.6.4 The battery pack or system should have warning system such as overtemperature, over voltage, over current, and so on.7. Battery pack assembly7.1 Prohibition of usage of damaged cell7.1.1 The cell should be inspected visually before battery assembly.7.1.2 The cell should not be used if sleeve-damage, can-distorsion and/orelectrolyte-smell is detected.7.2 Terminals handling7.2.1 Excessive force on the negative terminal should be avoided whenexternal strip terminal is welled.7.3 Transportation7.3.1 If the cell is necessary to be transported to such as the battery manufacturer,careful precautions should be taken to avoid damage of cell.8. Others8.1 Disassembly8.1.1 The cell should not be dismantled from the battery pack.8.1.2 Internal short-circuit caused by disassembly may lead to heat generationand/or venting.8.1.3 When the electrolyte is coming in contact with the skin or eyes,flush immediately with fresh water and seek medical advice.8.2 Short-circuiting8.2.1 Short-circuit results in very high current which leads to heat generation.8.2.2 An appropriate circuitry should be employed to protect accidentalshort-circuiting.8.3 Incineration8.3.1 Incinerating and disposing of the cell in fire are strictly prohibited,because it may cause rupture and explosion.8.4 Immersion8.4.1 Soaking the cell in water is strictly prohibited, because it may causecorrosion and leakage of components to be damaged to functions8.5 Mixing use8.5.1 Different types of cell, or same types but different cell manufacturer's shall not beused, which may lead to cell imbalance, cell rupture or damage to system due tothe different characteristics of cell.8.6 Battery exchange8.6.1 Although the cell contains no environmentally hazardous component,such as lead or cadmium, the battery shall be disposed according tothe local regulations when it is disposed.8.6.2 The cell should be disposed with a discharged state to avoid heat generationby an inadvertent short-circuit.8.7 CautionThe Battery used in this device may present a risk of fire or chemical burn ifmistreated.Do not disassemble, expose to heat above 100℃or incinerate it.Replace battery with those of Samsung SDI only.Use of another battery may cause a risk of fire or explosion.Dispose of used battery promptly.Keep battery away from children.Do not disassemble and do not dispose of battery in fire.8.8 Warning – Attached▣Pack Design Guideline (For electrical design)* Current of cell which full-charging shall be terminated.** Voltage condition of BMS which shall be shut down.*** Under 1.0V voltage, do not charge the cell.**** Voltage range of cell which shall be charged by Pre-charging.If a customer’s battery pack cannot meet the requirements above,SDI cannot take responsibility for a quality issue about a battery cell.▣ Pack Design Guideline (For mechanical design)If a customer’s battery pack cannot meet the requirements above,SDI cannot take responsibility for a quality issue about a battery cell.Handling precaution and prohibitions of lithium rechargeable cells and batteriesInaccurate handling of lithium ion and lithium ion polymer rechargeable battery may cause leakage, heat, smoke, an explosion, or fire.This could cause deterioration of performance or failure. Please be sure to follow instructions carefully.1.1 StorageStore the battery at low temperature (below 20℃is recommended), low humidity, no dust and no corrosive gas atmosphere.1.2 Safety precaution and prohibitionsTo assure product safety, describe the following precautions in the instruction manual of theapplication.[ Danger!]■Electrical misusageUse dedicated charger.Use or charge the battery only in the dedicated application.Don't charge the battery by an electric outlet directly or a cigarette lighter charger.Don't charge the battery reversely.■Environmental misusageDon't leave the battery near the fire or a heated source.Don't throw the battery into the fire.Don't leave, charge or use the battery in a car or similar place where inside of temperature may be over 60℃.Don't immerse, throw, wet the battery in water / seawater.■othersDon't fold the battery cased with laminated film such as pouch and Polymer.Don't store the battery in a pocket or a bag together with metallic objects such as keys, necklaces, hairpins, coins, or screws.Don't short circuit (+) and (-) terminals with metallic object intentionally.Don't pierce the battery with a sharp object such as a needle, screw drivers.Don't heat partial area of the battery with heated objects such as soldering iron.Don't hit with heavy objects such as a hammer, weight.Don't step on the battery and throw or drop the battery on the hard floor to avoid mechanical hock.Don't disassemble the battery or modify the battery design including electric circuit.Don't solder on the battery directly.Don't use seriously scared or deformed battery.Don't put the battery into a microwave oven, dryer ,or high-pressure container.Don't use or assemble the battery with other makers' batteries, different types and/or models of batteries such as dry batteries, nickel-metal hydride batteries, or nickel-cadmium batteries.Don't use or assemble old and new batteries together.[ Warning! ]Stop charging the battery if charging isn't completed within the specified time.Stop using the battery if the battery becomes abnormally hot, order, discoloration, deformation, or abnormal conditions is detected during use, charge, or storage.Keep away from fire immediately when leakage or foul odors are detected. If liquid leaks onto your skin or cloths, wash well with fresh water immediately.If liquid leaking from the battery gets into your eyes, don't rub your eyes and wash them with clean water and go to see a doctor immediately.If the terminals of the battery become dirty, wipe with a dry cloth before using the battery.The battery can be used within the following temperature ranges. Don't exceed these ranges.Charge temperature ranges : 0℃~ 45℃Discharge Temperature ranges : -20℃~ 60℃Store the battery at temperature below 60℃Cover terminals with proper insulating tape before disposal.[ Caution! ]■Electrical misusageBattery must be charge with constant current-constant voltage (CC/CV).Charge current must be controlled by specified value in Cell specification.Cut-off Voltage of charging must be 4.2V.Charger must stop charging battery by detecting either charging time or cur rent specified in Cell’s specification.Discharge current must be controlled by specified value in Cell’s specification.Cut-off Voltage of discharging must be over 2.5V.■othersKeep the battery away from babies and children to avoid any accidents such as swallow.If younger children use the battery, their guardians should explain the proper handling method andprecaution before using.Before using the battery, be sure to read the user's manual and precaution of it's handling.Before using charger, be sure to read the user's manual of the charger.Before installing and removing the battery from application, be sure to read user's manual of theapplication.Replace the battery when using time of battery becomes much shorter than usual.Cover terminals with insulating tape before proper disposal.If the battery is needed to be stored for an long period, battery should be removed from the application and stored in a place where humidity and temperature are low.While the battery is charged, used and stored, keep it away from object materials with static electric chargers.Safety Handling Procedure for the Transporter■Quarantine : Packages that are crushed, punctured or torn open to reveal contents should not be transported. Such packages should be isolated until the shipper has been consulted,provided instructions and, if appropriate, arranged to have the product inspected andrepacked.■Spilled Product : In the event that damage to packaging results in the release of cells or batteries,the spilled products should be promptly collected and segregated and the shippershould be contacted for instructions.Design of positioning the battery pack in application and chargerTo prevent the deterioration of the battery performance caused by heat, battery shall be positioned away from the area where heat is generated in the application and the charger.Design of the Battery PackBe sure adopting proper safe device such as PTC specified type or model in Cell Specification.If you intend to adopt different safety device which is not specified in Cell Specification, please contact Samsung SDI to investigate any potential safety problem.Be sure designing 2nd protective devices such as PTC & PCM at the same time to protect Cell just in case one protective device is fault.Please contact following offices when you need any help including safety concerns. Samsung SDI emergency contact information■Samsung SDI Headquarter.150-20, Gongse-ro, Giheung-gu, Yongin-si, Gyunggi-do, KoreaTel: +82-31-8006-3100, Fax : +82-31-210-7887■Samsung SDI Cheonan Factory.467, Beonyeong-ro, Seobuk-gu, Cheonan-si, Chungcheongnam-Do, KoreaTel: +82-41-560-3114, Fax : +82-41-550-3399■Samsung SDI America Subsidiary3655 North First St. San Jose CA 95134Tel: +1-408-544-4541, Fax : +1-949-260-2221■Samsung SDI Taiwan Branch9F-1,399 Ruey Kuang Road, Neihu, Taipei, TaiwanTel: +886-2-2656-8300, Fax : +886-2-2656-8329■Samsung SDI Malaysia factory.Lot 635 & 660, Kawasan Perindustrian, Tuanku Jaafar, 71450Sungai Gadut, Negeri Sembilan Darul Khusus, MalaysiaTel: (+60)6-677-6160, 6153。
2000mAh锂电池电池技术规格书
技术规格书型号：2000mAh编制：审核：批准：目录 Contents1. 范围 (3)2. 产品描述与型号 (3)3. 定义 (3)4. 产品规格 (3)5. 外形尺寸 (4)6. 外观 (4)7. 性能规格 (5)7.1 标准测试条件 (5)7.2 电性能 (5)7.3 环境适应性能 (6)7.4 安全性能 (6)7.5 机械性能 (6)8. 包装 (7)9. 运输 (7)8. 长期存储 (7)11. 保质期 (7)12. 产品责任 (7)电池组基本信息1.适用范围本产品规格书描述的是可充电锂离子电芯，包括产品规格信息、各种性能测试条件、产品责任及注意事项。
2.产品描述与型号2.1 产品描述: 电芯(可充电锂离子电池)2.2 型号 Model: 2000mAh3.定义3.1 标准模式充电标准模式充电的定义:在25±2℃下, 将电芯以0.5C电流恒流充电到4.2V, 然后转为在4.2V下恒压充电至截至电流0.01C。
3.2 标准模式放电标准模式放电的定义: 在25±2℃下, 将满电态电芯以0.2C电流恒流放电到3.0V。
4.产品规格工作温度和湿度范围充电 0 ~ 50℃60±25％R.H. 低温充电效率会下降，会影响电池使用寿命放电 -30 ~ 50℃60±25％R.H.电芯重量≤44.0±1.0g电芯尺寸高度≤65.50mm ；直径≤18.45 mm长时间存储温度-20~25℃60±25％R.H.不可超过半年，达到半年须充电一次带保护板电池3个月充电一次5.外形尺寸见附图图1. 外形尺寸6.主要零部件列表带帽PTC参数表7. 标准测试条件无其它指定时，按GB/18287-2013标准测试条件。
本规格书中所有的测试均在25±5℃（温度）≤75％RH（湿度）下进行；6.外观应没有如深度划痕、裂缝、生锈、斑点或漏液等影响电芯商业价值的外观瑕疵。
圆柱18650锂电规格 容量 详细资料
各种18650锂电池规格和容量容量松下-S O N Y锂电池的容量判断方法松下锂电池的容量判断方法蓝色c g r186501200m a h粉红色c g r186501350m a h黄色c g r18650h m1600m a h橙色c g r18650h g1800m a h紫色c g r18650H G L1800m a h浅绿色c g r18650a2000m a h`浅红色c g r18650c b2060m a h浅蓝色c g r18650c2200m a h锂电池容量标识蓝色的是1350m a hg21550m a h g30p1700m a h1800m a h g41950m a h2100m a h g62200m a hP a n a s o n i c C G R18650A F2050m A h型号 :P A N A S O N I C C G R18650A F标称容量 :2050m A h标称电压 :3.6V直径 :M a x18.6m m高度 :M a x65.2m m重量 :42gP a n a s o n i c C G R18650C2200m A h标称容量: 2150mAh标称电压: 3.6 V直径: Max 18.6mm高度: Max 65.2mm重量: 44.5 gP a n a s o n i c C G R18650C F2300m A h标称容量 :2250m A h标称电压 :3.6V直径 :M a x18.6m m高度 :M a x65.2m m重量 :45gP a n a s o n i c C G R18650D2400m A h标称容量 :2350m A h标称电压 :3.6V直径 :M a x18.6m m高度 :M a x65.2m m重量 :45gP a n a s o n i c C G R18650D A2450m A h 标称容量 :2450m A h标称电压 :3.6V直径 :M a x18.6m m高度 :M a x65.2m m重量 :45.5gP a n a s o n i c C G R18650E2550m A h标称容量 :2550m A h标称电压 :3.6V直径 :M a x18.6m m高度 :M a x65.2m m重量 :46.5gLG ICR18650P2 2000mAh型号: ICR 18650P2 2000mAh标称容量: 2000mAh(标准充放电)直径: 18.3±0.1 mm高度: 64.9±0.2 mm大概重量: 46.7 gLG ICR18650S2 2200mAh标称容量:2200m A h最低容量:2150m A h直径:18.3±0.1m m(M a x18.4m m)高度:64.8±0.2m m(M a x65.1m m)重量 (T y p i c a l)大约:44.5gLG ICR18650A2 2350mAh型号: LG ICR18650A2标称容量: 2350mAh(标准充放电)最小容量: 2300mAh直径: 18.3±0.1 mm (Max 18.4 mm)高度: 64.8±0.2 mm (Max 65.1 mm)大概重量: 46.5 gLG ICR18650A3 2430mAh型号 :L G I C R18650A3标称容量 :2430m A h最低容量 :2380m A h直径 :18.3±0.1m m(M a x18.4m m)高度 :64.8±0.2m m(M a x65.1m m)重量 :约 46.1gLG ICR18650B2 2600mAh型号: LG-18650-2600标称容量: 2600mAh(标准充放电)直径: 18.3±0.1 mm (Max 18.4 mm)高度: 64.9±0.2 mm (Max 65.1 mm)大概重量: 46.5 g-o U n2c p E w w w.6s q.n e t摩利（MOLICEL）18650产地：加拿大Model: ICR18650H容量: 2200mAhNominal V oltage: 3.75V重量: 46.1gM O L I C E L I C R18650J2400m A h标称容量: 2400mAh标称电压: 3.75V重量: 47g直径: 18.24 mm高度: 65.0 mmS A M S U N G I C R18650-202000m A h直径 :18.25m m高度 :65.0m m重量 :44gS A M S U N G I C R18650-222200m A h标称容量:2200m A h直径:18.25m m高度:65.0m m重量:46gS A M S U N G I C R18650-242400m A h标称容量:2400m A h直径:18.25m m高度:65.0m m重量:48gS A M S U N G I C R18650-262600m A h标称容量: 2600mAh重量(大约): 48gS A N Y O U R18650V1900m A h标称容量: 1900mAh重量: Max.46.0gS A N Y O U R18650H1900m A h标称容量: 1900mAh重量: Max.46.0gS A N Y O U R18650F H2000m A h型号: UR18650FH标称容量: 2000mAhS A N Y O U R18650F2200m A h标称电压 :3.7V重量: Max.46.5g直径: Max.18.1 mm高度: Max.64.8 mm三洋18650 SANYO 2400MAH绿头三洋18650 SANYO 2200MAH红头三洋18650 SANYO 2000MAH白头SONY2200MAH日本万胜18650电池，容量1800mah/2000mahB A K18650C42200m A h（比克电池）标称容量: 2200mAh标称电压: 3.0 V内部阻抗: < 70 m直径: 18.2±0.2 mm (Max 18.4 mm)高度: 64.80±0.3 mm (Max 65.1 mm)大概重量: 48 gS A P H I O N I F R18650E可充电锂离子电芯（磷酸铁锂型锂离子电池）充电电压：3.65V标准充电（最高4.2V）标称工作电压：3.2V@0.2C标称容量：1400mAh@0.2C标准放电方法：280mA@0.2C最大连续放电：2.8A(2C)最大瞬间放电：（30秒）5.6A(4C)放电截至电压：2.5V充电时间：标准充电2.5小时充电方法：恒流0.5C电流充电至3.65V，然后恒压充电直至电流小于0.05C循环寿命特性：到90%容量大于1000次循环工作温度：Charge O-C ~ 45-C; Discharge: -10-C ~ 50-C储存温度：400C~ 500C湿度：相对湿度5-95%电芯重量：38±2g电池尺寸：长：65±0.3mm;直径：18±0.3mmS A P H I O N I F R18650P可充电锂离子电芯（磷酸铁锂型锂离子电池）充电电压：3.65V标准充电标称工作电压：3.2V@1C标称容量：1100mAh@1C放电截至电压：2.0V充电时间：标准充电2.5小时工作温度：-10°C to 50°C储存温度：-40°C to +50°C电芯重量：39g电池尺寸：长：65±0.3mm;直径：18±0.3mm部分S O N Y锂电参数表C O K E C Y L I ND R:圆柱形，炭正极型号———电压—容量—长度———直径————重量U S14500—3.6—500——50.5———14.3————19U S14650—3.6—700——64.9———14.9————25U S17670—3.6—1270—66.8———16.9————38U S18650—3.6—1500—65.1———18.4————42U S26650—3.6—2800—65.4———26.3————83C O K E P R I S M:方形，炭正极h*L+c n.w h型号———电压—容量———长度——宽度————厚度——重量U S083488—3.6—850———7.9———33.7————48.1——35U S093448—3.6—950———8.6———34—————48.2——39U S103463—3.6—1650——10————34—————62.8——58G R A P H I T E C Y L I N D R:圆柱形，石墨正极型号————电压—容量——长度———直径————重量U S14430G—3.7——460——42.8———14—————17U S14500G—3.7——580——49.6———14.1————18U S14650G—3.7——780——64.9———14—————24U S17570G—3.7——1270——66.8———16.9————39U S18650G—3.7——1500——65.1———18.4————42G R A P H I T E P R I S M:方形，石墨正极型号————电压——容量——长度——宽度————厚度——重量0 U S083448G—3.7——620——6.3———29.5————47.8——25。
18650(1100)中文版规格书
1.适用范围本规格书规定了深圳市汇业电子有限公司向客户提供的18650 (1100mAh)圆柱型锂离子电池的技术参数及测试标准。
2.种类型号2.1种类：圆柱型锂离子二次电池2.2 型号：1 86501-1100mAh3.参考标准此规范参考GB/T18287-2000、UL1642及IEC61960—1：2000等技术标准规范编制。
4. 注意事项4.1在测试或使用电池之前，请仔细阅读本规格书，以防止不当操作引起电池功能失效、发热、漏液、起火甚至爆炸；4.2 对电池进行充放电测试时，请使用锂离子电池专用测试设备，严禁使用普通恒流恒压源等不能限压限流设备对电池进行充放电，以避免电池被过充过放而引起电池功能失效或发生危险；4.3对电池充放电或将电池装入设备时，注意不要将电池正负极反置，否则将会使电池发生过充过放，导致电池严重失效甚至发生爆炸等危险；4.4不要直接对电池进行焊接，严禁对电池进行分解；4.5不要把电池同项链、发夹、硬币或螺丝等金属品一起放在兜中或包中，也不要把电池同上述物品一起储存，严禁用金属等导电材料直接连接电池正负极而使电池发生短路；4.6禁止敲击、抛掷或踩踏电池，更不要将电池放入洗衣机或高压容器内；4.7请勿将电池靠近热源，如火、加热器等，不要在烈日下或在温度超过60℃的条件下使用或存放电池，否则可能会引起电池发热、起火及功能失效等；4.8不要将电池弄湿或将电池投入水中，暂不使用时，请放置在低温干燥的环境中；4.9使用、测试或存放电池时，如发现电池有变热、散发气味、变色、变形或其它反常时，请立即停止使用或测试，设法隔离电池并远离；4.10如电池漏液并不慎将电解液溅入眼睛，不要揉擦你的眼睛，立刻用干净的水清洗，严重时请去医院就医，如皮肤或衣物溅上电解液，则需马上用清水清洗干净。
5.6. 测试条件7. 外观外表清洁，无机械损伤、漏夜、锈蚀；另表面有必须的产品标识。
8. 性能9. 包装电池在包装时需处于半充满状态,包装箱外应标明产品名称、型号、标称电压、数量、毛重、出厂日期及相应等级的内阻、容量。
18650F2P-2000mAh新版规格书(中文)
创明新能源股份有限公司锂离子二次电池规格书高能倍率圆柱型电池CMICR18650F2P-2000mAh编制审核批准宇妍赵悠曼程建良2013-09-18发布2013-09-18生效1.适用范围本规格书规定了创明新能源股份有限公司向客户提供的CMICR18650F2P(2000mAh)圆柱型锂离子电池的技术参数及测试标准。
该参数及标准的拟定，主要参照GB/T18287-2013《移动电话用锂离子蓄电池及蓄电池组总规范》。
2.型号类别2.1类别：圆柱型锂离子二次电池2.2型号：CMICR18650F2P-2000mAh3.基本规格及性能3.1容量标称容量：2000mAh(0.2C放电至3.0V)最低容量：1950mAh(0.2C放电至3.0V)3.2标称电压 3.6V3.3电池内阻≤20mΩ3.4放电终止电压 3.0V3.5充电上限电压4.20±0.05V 3.6标准充电电流0.2C3.7快速充电电流1C3.8标准放电电流0.2C3.9最大持续放电电流10C3.10最大瞬间放电电流20C(<200ms) 3.11电池重量44.0±1g3.12最大尺寸直径(φ):18.6mm 高度(H):65.3mm3.13工作温度充电：0~45℃；放电：-10~60℃3.14贮存温度1个月内：-5~45℃6个月内：0~45℃4.测试条件实验和测量要在标准温度(23±2)℃及标准湿度(65±20)%的条件下进行。
4.1标准充电0.2C恒流恒压充电(CC/CV)至上限电压4.20+/-0.05V，然后以0.02C电流截止；4.2标准放电以0.2C恒流放电至3.0V电压截止5.性能5.1电性能项目测试程序标准5.1.1标称电压电池按4.1充满电后，按0.2C放电过程的平均工作电压. 3.6V 5.1.2放电性能电池按4.1充满电后，以0.2C恒流放电到3.0V。
≥292min5.1.3循环寿命常规寿命在环境温度23±2℃的条件下，以0.5C先恒流充电至上限电压4.20+/-0.05V，再恒压充电至0.02C截止电流；搁置10min后以1C放电至3.0V，放电结束后搁置10min后进行下一个循环，直至连续两次放电容量为首次的80%，则认为寿命终止。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
容量(20oC, 0.2 C5to 2.75V)
最小容量-------------------------------------- 2000mAh
内阻（20℃5℃，完全充电后测量）------------小于80mΩ
标准充电--------------------------------------- 0-45℃
相对湿度------------------------------------------ <93%
大气压力------------------------------------- 86-106kPa
充电条件(20℃5℃)
标准充电-------- 1000mA至4.2V,4.2V恒压至电流小于20mA
快速充电--------- 1500mA至4.2V,4.2V恒压至电流小于20mA
使用环境（建议）
储存---温度(15-35℃)相对湿度(45-75%)大气压力(86-106kPa)
放电------------------------------------------ -20-60℃
标准测试环境(除非另外要求)
温度----------------------------------------- 20℃±5℃
相对湿度--------------------------------------- 45±20%
如有更改，以新版本为准，不另行通知。
1.性能
检测项目
检测条件
要求
(1)外观结构
振幅：1.6,(p-p)
频率：10-55Hz(1Hz/min)
方向：X,Y
不泄漏、不泄气、不爆炸、不起火，电池的工作性能和外观无影响。
(2)跌落实验
将100%充电的电池从1m的高度上跌落到放置在水平地面上5cm厚的硬木板上,每面跌落两次。
不泄漏、不泄气、不爆炸、不起火，电池的工作性能和外观无影响。
3安全特性
目测
无破裂、划痕、变形、污迹、电解液泄露。
(2)标准测试条件
如果没有特殊要求测试应在20±5℃（温度）、65±20%（湿度）条件下进行。
测试中所使用的电流表和电压表的精度等级≤0.5
(3)标准充电
指在20+5℃，65±5%RH环境下，1）以0.5ItmA电流充电至单体电池电压4.2V后，2）转为恒压4.2V充电，至充电电流小于20mA，停止充电。
可充锂离子电池
型号-------------------------------------- ICR18650
规格------------------------------------------ 18650
标称电压-------------------------------------- 3.6V
(4)快速充电
指在20+5℃，65±5%RH环境下，1）以1500mA电流恒流充电至单体电池电压4.2V后，2）转为恒压4.2V充电，至充电电流小于20mA，停止充电。
(5)运输定容量
指在20+5℃，65±5%RH环境下，1）充电前电池以0.5ItmA恒流放电至终止电压2.75V；2）标准充电后搁置15分钟；3）以0.2ItmA放电至2.75V时的放电容量。
德赛能源科技有限公司
承认书
文件名称: 18650圆柱型锂离子电芯
文件编号:D.DD.S–01-138
送交确认
批准:余翔审核:何德强承办:卢成钢
此标准文件仅供贵司确认之用。当贵司确认后，我司将根据贵司反馈意见发放正式受控文件。
类型------------------------------------密封圆柱型
检测项目
检测条件
要求
(1)热箱试验
将充满电的电池放在重力对流或循环空气的烘箱中进行加热，烘箱的温度要以每秒5±2℃的速率上升到150±2℃后保温30分钟。
不泄漏、不泄气、不爆炸、不起火。
(2)短路实验
将充满电电池的正负极使用最低可承受50A电流的导线短接到一起，外电路总电阻小于50mΩ，当电池温度下降到比峰值低约10℃时结束。
≥300次
(9)-20℃放电性能
1)电池应按标准充电方式充电；2)电池应在-20℃2℃的环境温度下搁置16h～24h；3)电池应在-20℃2℃的环境温度下以0.2ItmA恒流放电至终止电压2.75V；4）计算放出的容量
放电容量：
≥60%C5mAh
2机械特性
检测项目
检测条件
要求
(1)振动试验
在室温条件下将充满电的电池放在振动平台上按照下面的参数要求振动90分钟：
最大充电终止电压------------------------------- 4.23V
最大持续充电电流------------------------------ 1500mA
最大持续放电电流----------------------------- 3000mA
尺寸(包括热缩外套)
直径，d ---------------------------------- 18.0±0.2mm
重量------------------------------------------约45g
C5mAh---------------------------------------- 2000mAh
充电电压------------------------------- 4.200±0.049V
最小放电终止电压------------------------------- 2.75V
不泄漏、不泄气、不爆炸、不起火。
放电容量:
≥100%C5mAh
（7）快速放电容量
指在20+5℃，65±5%RH环境下，1）充电前电池以0.2ItmA恒流放电至终止电压2.75V；2）标准充电后搁置15分钟；3）以1500mA放电至2.75V时的放电容量。
放电容量:
≥90%C5mAh
(8)循环寿命
试验前，1)按标准放电的要求对电池进行放电后搁置15分钟。2)在20+5℃，65±5%RH环境下，按快速充电要求充电后搁置15分钟，3)以1500mA的电流进行放电，至电池端电压达到终止电压2.75V。按照2)和3)循环充放电，当任一次循环的放电容量小于80%C5mAh，寿命终止。