DECLARATION OF CONFORMITY
一致性声明
DECLARATION OF CONFORMITY我，(制造商名称) xxxx电气有限公司公司声明，(生产厂名称) xxxx电气有限公司生产的(详细填写产品名称、规格/型号) 动力柜SDXL主母线:In=630A～100A,Icw=10kA;Ue=380V,Ui=660V;50Hz;IP30符合如下要求：a) 中华人民共和国国家标准：____GB7251.1-2005_b) 其它相关标准或规定：_____________________________________________我公司对上述声明完全负责。
We,(manufacturer’s name)_ _ declare under our sole responsibility that the product (detailed description of product including name type or model)_________ ______ product in (factory’s name and address): _ _________ to which this declaration relates is in conformity with:a) GB standards; _b) And ot her standards and/or regulation________________________ _____________________(签署时间及地点) (负责人签名)(Place & Date of issue) (Name & Signature)DECLARATION OF CONFORMITY我，(制造商名称) xxx电气有限公司公司声明，(生产厂名称) xxxx电气有限公司生产的(详细填写产品名称、规格/型号) GGD主母线:In=1600A～630A,Icw=30kA;配电母线:In=630A,Icw=30kA;Ue=380V,Ui=660V;50Hz;IP30符合如下要求：a) 中华人民共和国国家标准：____GB7251.1-2005 _b) 其它相关标准或规定：_____________________________________________我公司对上述声明完全负责。
Declaration of Conformity说明书
NumberK86656/02IssuedJuly 9th, 2015ValidJuly 10th, 2016Declaration of Conformity,based on parts of UL subject 2775, regardingDSPANon-Pressurized Condensed Aerosol Generators andComponentsKiwa Nederland B.V.Groningenweg 10Postbus 2562800 AG GoudaTel. +31-182-820460Fax +31-182-820465Internet www.kiwafss.nlCompanyDSPA B.V.Hulzenseweg 10-206534 AN NIJMEGENP.O. Box 65726503 GB NIJMEGENThe NetherlandsTel. +31 24 352 25 73Fax +31 24 37 87 583www.dspa.nlThis declaration consists of 11 pages.Publication of the declaration is allowed.Note: Publication of only this front page or parts of the declaration is considered as “not valid”.Underwriters Laboratories (or UL in short) was not involved with the performed tests asmentioned in this product declaration.STATEMENT BY KIWAWith this declaration, Kiwa declares that legitimate confidence exists that theproducts supplied byDSPA B.V.complying with the technical specifications as laid down in this productdeclaration and marked with the Kiwa®-mark in the manner as indicated inthis product declaration.Bouke MeekmaKiwaDeclarationThis product declaration by Kiwa is based on test protocol PRO10-001-AFG-nk rev 06 and parts of UL subject 2775.Please note that Underwriters Laboratories (or UL in short) was not involved with the performed tests as mentioned in this product declaration.Generator specificationsThe products mentioned below belong to this product declaration.DSPA 11-1, DSPA 11-2, DSPA 11-3, DSPA 11-4, DSPA 11-5, DSPA 11-6, DSPA 11-7 and DSPA 8-1.Type HousingRed coated steelActivationDSPA 11-1 Disk, radial, double shaped plate ElectricalDSPA 11-2 Disk, radial, double shaped plate ElectricalDSPA 11-3 Disk, radial, double shaped plate ElectricalDSPA 11-4 Disk, radial, double shaped plate ElectricalDSPA 11-5 Disk, radial, double shaped plate ElectricalDSPA 11-6 Disk, radial, double shaped plate ElectricalDSPA 11-7 Disk, axial, double shaped plate ElectricalDSPA 8-1 Cylindrical, axial ElectricalNon-pressurized generator.Application and useThis product declaration covers the construction and operation of condensed aerosol generators for total flooding applications when installed, inspected, tested, and maintained in accordance with the Standard for Fixed Aerosol Fire Extinguishing Systems, NFPA 2010. The fire extinguishing components shall be suitable for extinguishing fires of the following classes:•Class A according NFPA 2010•Class B according NFPA 2010•Class C according NFPA 2010Conditions for application•The numbers and types of the extinguishing components have to be determined in conformity with the guidelines and calculation methods of the supplier.•Distribution is to be done by supplier or companies authorised by the supplier.•Before usage an instruction is to be given by a trainer or instructor for this product authorized by the supplier.•The installation and maintenance of the fire extinguishing components have to take place according to the specifications of the supplier, NFPA 2010 or evaluation guideline BRL-K23003.Point of interest during use or limitation of useThe condensed aerosol extinguishing components should not be used on fires involving the following unless relevant testing by accredited testing laboratories has been carried out to the satisfaction of the Authority:•Deep seated fires in Class A materials•Certain chemicals or mixtures of chemicals material, such as cellulose nitrate and gunpowder, that are capable of rapid oxidation in the absence of air•Reactive metals such as lithium, sodium, potassium, magnesium, titanium, zirconium, uranium and plutonium.•Metal hydrides•Chemicals capable of undergoing auto thermal decomposition, such as certain organic peroxides and hydrazine•Condensed aerosol generators shall not be used to protect classified hazards or similar spaces containing flammable liquids or dusts that can be present in explosive air–fuel mixtures unless the generators are specifically listed for use in those environments. •Temperatures for use of aerosol extinguishing agents shall be within the supplier’s listed limits.•Unless specifically approved as an agent blend or mixture, systems employing the simultaneous discharge of different agents to protect the same enclosed space shall not be permitted.•Where unrelated extinguishing or suppression systems, such as a sprinkler system or a gaseous fire-extinguishing system are provided and can operate prior to or during the hold time of the aerosol system, the other agent shall not adversely affect the aerosol.The above list may not be exhaustive.•The design, installation, service, and maintenance of aerosol systems shall be performed by persons skilled in aerosol fire-extinguishing system technology.•Local applications 1) of condensed aerosol extinguishing systems are not covered by this product declaration.•Local applications require a pre-engineered and pre-designed system which has been tested and approved for a specific application by a authority such as Kiwa or by an accredited testing laboratory.1) a local application is used for the extinguishment of surface fires in flammable liquids, gasses, and shallow solids, where theenclosure does not conform to the requirements for total flooding.Owner’s manualAt delivery the product should be accompanied by an operation manual in the English language, known and authorized by Kiwa.Following minimum items shall be described according UL 2775:•Clear indication that it is not a detailed design, installation, operation, and maintenance instruction manual.•Clear reference to the availability of the design, installation, operation, and maintenance instruction manual by contacting the supplier.• A statement that periodic inspection is conducted by trained personnel.•Information regarding the essentials required to maintain the extinguishing system unit in operation both before and after a fire. •For extinguishing system units, a statement that no modifications are to be made to the extinguishing system unit without consultinga qualified designer who is to refer to the detailed design, installation, operation, and maintenance instruction manual. The statementshall include the following or equivalent wording: “This system is made up of units tested within limitations contained in the detailed design, installation, operation, and maintenance instruction manual.The designer must be consulted whenever changes are planned for the system or area of protection. An authorized installer or designer must be consulted after discharge”.Design, Installation, Operation, and Maintenance Instruction ManualAt delivery the product should be accompanied by an operation manual in the English language, known and authorized by Kiwa.Following minimum items shall be described according UL 2775:•Description of all variations of each unit, including the limitations for each variation;•Operating temperature range limitations;•Mass of aerosol-forming compound for each condensed aerosol generator size;•Discharge time for each condensed aerosol generator size;•Reference to the type of occupancy to be protected;•Reference to NFPA 2010, “Standard for Fixed Aerosol Fire Extinguishing Systems” for installation, inspection, testing, and maintenance requirements;•Material Safety Data Sheet (MSDS) information and cautionary instructions;•Description of the design procedure and typical layout with specific limitations and recommendations for correct installation and effective protection;•Specific information for condensed aerosol generator placement within the enclosure and orientation of discharge port(s); •Minimum safe distance between condensed aerosol generator discharge ports and personnel;•Minimum safe distance between condensed aerosol generator discharge ports and combustible materials;•Minimum safe distance between condensed aerosol generator casing and personnel;•Minimum safe distance between condensed aerosol generator casing and combustible materials;•Information on inspection after installation;•Description of requirements for maintenance of all equipment;• A list of part numbers for all replacement parts;•Useful life limitation for mandatory replacement of the condensed aerosol generators;•The name of the supplier or private labeller, or equivalent designation; and•Date and manual designation number on each page.•Description and operating details of each unit, mounting brackets, and all accessory equipment (as applicable), including identification by part or model number;•Degree and type of protection with associated design application densities for surface-type Class A and Class B fires including design application density limitations;•Condensed aerosol generator discharge port limitations, including maximum dimensional and area coverage, minimum and maximum height limitations, and location in the protected volume.•For extinguishing system units, reference to the specific types of detection and control panels (when applicable) intended to be connected to the extinguishing system unit;•For extinguishing system units, specifications and instructions for interconnection of multiple extinguishing system units; or when a means for interconnecting is unavailable, a caution statement to not use multiples of extinguishing system units;•Details on installation of each unit, mounting brackets, and all accessory equipment (as applicable);MarkingThe products should be marked with the Kiwa®-mark.Place of the mark Required specifications Method of marking•On the generator •Name of the product and supplier•Supplier’s type designation•Production date and serial number•Mass of aerosol-forming compound•Temperature range•Storage humidity range•Service life•Distances as specified in table 5•Reference to the applicationinstructions•Certification mark•Fire Class A according EN2•Fire Class B according EN2 •Non-erasable and non-detachable; •Non-flammable;•Permanent an legibleRecommendations for CustomersCheck at the time of delivery whether:•The supplier has delivered in accordance with the agreement;•The mark and the marking method are correct;•The products show no visible defects as a result of transport etc.If you should reject a product on the basis of the above, please contact:•DSPA B.V.and, if necessary,•Kiwa Nederland B.V.Consult the suppliers processing guidelines for the proper storage and transport methods.Cross referenceUL subject 2775, outline of investigation for fixed condensed aerosol extinguishing system units, November 5, 2008Chapter Description Demand 1)Result RemarksIntroduction1. Scope Implemented2. Components Implemented3 Units of measurements Implemented4 Undated references Implemented5 Glossary ImplementedConstruction6 General Implemented7 Electrically operating alarm N/A8 Control and indicators N/A9 Pneumatic control assembly pressure vessels N/A10 Pressure relief devices for pneumatic control assemblies N/A11 Gaskets and O-rings N/A12 Pressure gauges for pneumatic control assemblies N/A13 Puncturing mechanisms N/A14 Electrically operating devices N/A15 Condensed aerosol extinguishing agents A Pass See SNAP listing by USEnvironmental ProtectionAgency (EPA)16 Pneumatic control gases N/A17 Polymeric materials and nonmetallic parts N/A18 Anti-recoil devices N/A19 Pressure switches N/APerformance20 General Implemented21 Discharge test A See table 4.Discharge time of DSPA 8-1 isover 60 sec.Chapter Description Demand 1)Result Remarks22 Temperature measurement test A Pass See table 5.23 Mounting device test A Pass24 Rough Usage test A Pass25 Vibration test A Pass ImplementedDSPA 11-3, DSPA 11-6, DSPA11-7 and DSPA 8-1 were tested.DSPA 11-1, DSPA 11-2, DSPA11-4 and DSPA 11-5 aremembers of the same generatorfamily as DSPA 11-3 and DSPA11-6.DSPA 8-1 only at 0,5G26 Pyrotechnic reaction containment test Not Tested27 Fire exposure test Not Tested28 High humidity test A Pass29 Moist hydrogen sulfide air mixture corrosion test A Pass30 Moist carbon dioxide sulfur dioxide air mixture corrosionA Passtest31 Salt spray corrosion test A Pass32 Thirty day elevated temperature test A Pass33 Temperature cycling test A Pass34 One-year time leakage test N/A35 Hydrostatic pressure test N/A36 Pressure relief tests N/A37 Flexible hose assembly hose low temperature test N/A38 Calibration test gauges N/A39 Burst strength test gauges N/A40 Overpressure test gauges N/A41 Impulse test gauges N/A42 Pressure relief test gauges N/A43 Water resistance test gauges N/A44 Pneumatic operation test N/AChapter Description Demand 1)Result Remarks45 Pneumatic time delay verification test N/A46 Pressure operated alarm test N/AN/A47 Operation test of manual activators and manual pullstations48 500 cycle operation test Implemented48.1 Electrical initiators A Pass Aging test 116 days at 90 ºC =15 years and Temperature range-40°C and +75°C48.2 Other devices N/A49 Class A and B fire extinguishment tests Implemented49.1 General Implemented49.2 Class A fire extinguishment tests A Pass Not tested:Wood cribs according 49.2.2See table 1.49.3 Class B fire extinguishment tests A Pass See table 1.Implemented50 Distribution verification extinguishment tests withextinguishing system units50.1 General Implemented50.2 Test enclosure Implemented50.3 Maximum area coverage and minimum height testA Pass See table 3.arrangement procedure50.4 Maximum height test procedure A Pass See table 3.N/A51 Distribution verification extinguishment test with automaticextinguisher unit51.1 General N/A51.2 Test enclosure N/AN/A51.3 Maximum area coverage, minimum height and maximumvolume test arrangement procedure51.4 Maximum height and maximum volume test arrangementN/AprocedureN/A52 Automatic extinguisher unit automatic operationextinguishment unitChapter Description Demand 1)Result Remarks52.1 General N/A52.2 Test enclosures N/A52.3 Test arrangement procedure N/A53 Elastomeric parts test N/A54 Stress corrosion cracking test for brass parts A Pass Materials used in theconstruction are not susceptibleto ammonia stress corrosion.55 Aging test condensed aerosol generator Pass 116 days at 90 ºC = 15 years56 Aging test plastic materials N/A56.1 Air-oven aging test N/A56.2 Light and water test N/A57 Nameplate exposure test N/A58 Nameplate adhesion test N/A59 Nameplate abrasion test N/A60 Locking device and tamper indicator test N/AManufacturing and production tests61 General Implemented61.1 General Implemented61.2 Aerosol-forming compound A Pass61.3 Electrical initiators A PassN/A61.4 Hydraustatic pressure test – shells for pneumatic controlassemblies61.5 Gauge calibration test for pneumatic control assemblies N/A61.6 Leakage test for pneumatic control assemblies N/AMarkings62 General A PassInstructions63 General Implemented64 Owner’s manual A Pass See DSPA Manual V7.3 201565 Design, installation, operating and maintenance instruction A Pass See DSPA Manual V7.3 2015Chapter Description Demand 1)Result Remarks manual1) A = Applicable N/A = Not Applicable Not testedTests not performed (with requirements):•Aerosol generator explosive atmosphere test according to UL 2775 § 26•Fire Exposure test according to UL 2775 § 27•Wood cribs test according to UL 2775 § 49.2.2Page 10 of 11DSPA Non-Pressurized Condensed Aerosol Generators and Components Product specificationsTable 1Fire Class Listing AccordingUL 2775Pre burntimeSoak period Test room Density Material / fuel in seconds in seconds in m3in grams per m3A & C Polymethylmethacrylate 49.2.3 210 600 112.12 97 A & C Polypropylene 49.2.3 210 600 112.12 58A & C ABS 49.2.3 210 600 112.12 87B Heptane 49.3 30 30 112.12 34 Table 2Type Efficiency in %DSPA 11-1 100DSPA 11-2 88 - 100DSPA 11-3 90 - 100DSPA 11-4 100DSPA 11-5 94 - 100DSPA 11-6 100DSPA 11-7 100DSPA 8-1 100Table 3Type HousingType andDischargemethod Agent distribution according UL2775Minimum height /Maximum area coverage (in m)Maximum height /Maximum area coverage (in m)DSPA 11-1 Disk, radial 0.5 3.66 x 1.22 1.83 1.22 x 1.22 DSPA 11-2 Disk, radial0.5 3.66 x 2.44 2.44 1.22 x 1.22 DSPA 11-3 Disk, radial0.5 3.66 x 2.44 2.44 1.22 x 1.22 DSPA 11-4 Disk, radial 1.22 3.66 x 3.66 3.05 1.83 x 1.83 DSPA 11-5 Disk, radial 1.22 4.88 x 3.66 3.66 2.44 x 2.44 DSPA 11-6 Disk, radial 1.227.32 x 3.66 3.66 2.44 x 2.44 DSPA 11-7 Disk, axial 1.227.32 x 1.22 3.05 1.83 x 1.83 DSPA 8-1 Cylinder, axial 2.44 9.76 x 3.66 4.88 4.88 x 3.66Table 4Type Discharge timeIn SecDSPA 11-1 6 - 10DSPA 11-2 9 - 15DSPA 11-3 14 - 26DSPA 11-4 19 - 31DSPA 11-5 40 - 60DSPA 11-6 30 - 50DSPA 11-7 30 - 50DSPA 8-1 67 - 89Kiwa® product declaration K86656/02 Page 11 of 11DSPA Non-Pressurized Condensed Aerosol Generators and ComponentsTable 5Type Distance in m75°C 200°C 400°CDSPA 11-1 0.5 0.15 0.05DSPA 11-2 0.5 0.15 0.05DSPA 11-3 0.5 0.15 0.05DSPA 11-4 1.0 0.25 0.15DSPA 11-5 1.0 0.25 0.15DSPA 11-6 1.5 0.35 0.15DSPA 11-7 1.5 0.50 0.10DSPA 8-1 1.5 0.75 0.15。
DOC模板 - EU Declaration of Conformity 2015-06-15
符合性（自我）声明 - 针对EMC按符合性评定模式A进行评估的电子产品
需要更新为最新版的指令，
例如EMC 为2014/30/
EU，LVD为2014/35/EU.
符合性声明 - 针对已获得由公共机构出具EMC报告/证书的电子产品
需要更新为最新版的指令，
例如EMC 为2014/30/
EU，LVD为2014/35/EU.
符合性（自我）声明 - 针对在MD指令附录IV之外且按符合性评定模式A进行评估的机械产品
需要更新为最新版的指令，
例如EMC 为2014/30/
EU，LVD为2014/35/
EU，MD为2006/42/EC.
符合性声明 - 针对已获得由公告机构EMC报告/证书，且在MD指令附录IV之外且按符合性评定模式A进行评估的机械产品
需要更新为最新版的指令，
例如EMC 为2014/30/
EU，LVD为2014/35/
EU，MD为2006/42/EC.。
declaration-of-conformity-符合性声明---mdd原件讲课稿
D e c l a r a t i o n-o f-C o n f o r m i t y-符合性声明--2010-M D D原件M ANUFACTURER: NAME AND ADDRESSM EDICAL D EVICE: NAME, TYPE AND / OR MODELOR S EE A TTACHED L IST - INCLUDE UMDNS AND/OR GMDN[NAME AND CODE]C LASSIFICATION -A NNEX IX: E.G.CLASS II A, RULE 11C ONFORMITY ASSESSMENT R OUTE: E.G.A NNEX VII+V.3W E, THE MANUFACTURER, HEREWITH DECLARE THAT THE STATED MEDICAL DEVICESMEET THE TRANSPOSITION INTO NATIONAL LAW, THE PROVISIONS OF C OUNCIL D IRECTIVE 93/42/EEC OF 14 JUNE 1993 CONCERNING MEDICAL DEVICES;INCLUDING, AT 21 MARCH 2010, THE AMENDMENTS BY C OUNCIL D IRECTIVE 2007/47/EEC.A LL SUPPORTING DOCUMENTATION IS RETAINED AT THE PREMISES OF THE MANUFACTURER.S TANDARDS APPLIED:EN ISO13485:2003/AC2007,EN ISO14971:2007,EN ISO11135-1:2007,EN ISO 11607-1,EN ISO11607-2,EN ISO10993-1:2003,EN556-1,EN1041:2008,EN980:2008以及适用的产品协调标准，至于有哪些标准，具体察看协调标准网站N OTIFIED B ODY:TÜV SÜD P RODUCT SERVICE G MB HR IDLERSTR 65,D-80339MÜNCHEN,G ERMANY IDENTIFICATION NUMBER 0123(EC)C ERTIFICATE(S): EC CERTIFICATE(S) NUMBER(S)SHOW ONLY THE EC CERTS WITH A SCOPE THAT COVERS THE PRODUCTS LISTEDE UROPEAN R EPRESENTATIVE: Shanghai International Trading Corp. GmbH (Europe)Eiffestrasse, 80, D-20537, Hamburg, Germany Tel: 0086-021-65951371，0049-40-2513175，Fax: 0049-40-255726S TART OF CE-MARKING: D ATE OF FIRST CE MARKING (OR LOT OR SERIAL NUMBER)USUALLY = ISSUE DATE OF EC CERT.(AND ADD END DATE - WHEN EC CERT. VALIDITY ENDS,OR WHEN DEVICE CEASES TO BE MARKETED, OR WHEN NB IS CHANGED)P LACE,D ATE OF D ECLARATION: CITY, DATES IGNATURE: ____________________NAME:POSITION:(RESPONSIBLE S ENIOR E XECUTIVE OF MANUFACTURER)。
FCC认证简介
FCC认证简介一、FCC 简介为了履行通信法、各种条约以及国际规定所赋予的职责，为了促进更加有效的利用频谱资源，美国联邦通信委员会为射频设备制定了技术标准。
对于大多数的电子电气产品而言，主要是FCC Part 15和FCC Part 18。
二、怎样获得FCC？欲获得FCC的认证，对不同的产品有分别不同的三种认证模式，分别为：Verification，Declaration of Conformity (DoC)，Certification。
不同的认证模式，都要求测试实验室取得ＦＣＣ认可，并且有不同的申请、测试以及申明要求。
Verification是制造厂商自行采取一定的步骤从而保证产品符合相应的技术标准的过程。
Declaration of Conformity是由responsible party采取一定的步骤从而保证产品符合相应的技术标准的过程。
Certification是FCC基于申请和测试数据而签署设备认可的过程。
三、FCC标志及声明FCC规定了加帖标志和声明的要求：对于采用Verification和Certification的射频设备，一般而言需要在设备上明显的位置加帖声明：对于采用DoC的射频设备，一般而言需要在设备上明显的位置加帖声明：对于采用DoC的工、科、医设备，需要在设备上明显的位置加帖FCC标志和声明：五、FCC Part 15FCC Part 15对于有意的、无意的或者瞬时的并且在使用中无需个人许可证的发射设备做出了规定。
它包括技术规范、行政要求以及其它的市场准入条件。
FCC Part 15针对的是射频产品，主要分为四类：无意发射设备、有意发射设备、不用许可证的个人通讯设备、不用许可证的国家的基础信息设备。
六、FCC Part 18FCC Part 18对于在一定频谱上工作的工业、科学以及医学设备（ISM）所发射的电磁能量做出了规定，以避免上述设备对已获授权的无线通讯服务产生有害的干扰。
格兰富安装和维护手册
带 EPDM 橡胶件 , HxxE, H 型轴封的 CRI 和 CRN 型水泵可以用温 度最高达到 150 °C 的液体就地清洗 (CIP)，最长时间为 15 分钟。
注意
泵送温度超过 +120 °C 的液体可能导致周期性噪音并 可缩短泵的寿命。
CR, CRI, CRN 泵不适用于长时间泵送温度 120 °C 以上的液体。
5.4 最小入口压力
Hf
H
Pb
NPSH
Hv
图 4 配置一个 CR 泵的开放系统示意图
以米水头计算的最大吸程 "H" 可以从下式得出 :
H = pb x 10.2 – NPSH – Hf – Hv – Hs
pb
=气压计大气压值，以巴为单位。
( 可以将大气压力设置为 1 巴。) 在封闭的系统中，pb 表
4
Start the pump and check the direction of rotation.
6
Continue to vent the pump. At the same time, open the discharge isolating valve a little more.
8
For further information, see page 21.
3.2 CR, CRN 32, 45, 64, 90, 120 和 150 型号名称说明
17
4. 用途
17
5. 技术数据
17
5.1 环境温度和海拔高度
17
5.2 液体温度
17
5.3 轴封的允许最大运行压力和液体温度
18
5.4 最小入口压力
18
5.5 最大入口压力
DeclarationofConformity符合性声明2010MDD原件.doc
DECLARATION OF C ONFORMITYTO C OUNCIL D IRECTIVE 93/42/EEC OF 14 J UNE 1993CONCERNING M EDICAL D EVICESRef: EN ISO/IEC 17050-1 revision date: June 2009 M ANUFACTURER :NAME AND ADDRESSM EDICAL D EVICE :NAME , TYPE AND / OR MODEL OR S EE A TTACHED L IST - INCLUDE UMDNS AND /OR GMDN [NAME AND CODE ]C LASSIFICATION - A NNEX IX : E .G . CLASS II A , RULE 11C ONFORMITY ASSESSMENT R OUTE : E .G . A NNEX VII + V.3W E , THE MANUFACTURER , HEREWITH DECLARE THAT THE STATED MEDICAL DEVICES MEET THE TRANSPOSITION INTO NATIONAL LAW , THE PROVISIONS OF C OUNCIL D IRECTIVE93/42/EEC OF 14 JUNE 1993 CONCERNING MEDICAL DEVICES ;INCLUDING , AT 21 MARCH 2010, THE AMENDMENTS BY C OUNCIL D IRECTIVE 2007/47/EEC. A LL SUPPORTING DOCUMENTATION IS RETAINED AT THE PREMISES OF THE MANUFACTURER .S TANDARDS APPLIED : EN ISO 13485:2003/AC 2007, EN ISO 14971:2007, EN ISO 11135-1:2007, EN ISO 11607-1, EN ISO 11607-2, EN ISO 10993-1:2003, EN 556-1, EN1041:2008, EN 980:2008以及适用的产品协调标准，至于有哪些标准，具体察看协调标准网站N OTIFIED B ODY :TÜV SÜD P RODUCT SERVICE G MB HR IDLERSTR 65, D-80339 M ÜNCHEN , G ERMANYIDENTIFICATION NUMBER0123(EC) C ERTIFICATE (S ): EC CERTIFICATE (S ) NUMBER (S )SHOW ONLY THE EC CERTS WITH A SCOPE THAT COVERS THE PRODUCTS LISTEDE UROPEAN R EPRESENTATIVE : Shanghai International Trading Corp. GmbH (Europe)Eiffestrasse, 80, D-20537, Hamburg, Germany Tel: 0086-021-65951371，0049-40-2513175，Fax: 0049-40-255726S TART OF CE-MARKING : D ATE OF FIRST CE MARKING (OR LOT OR SERIAL NUMBER ) USUALLY = ISSUE DATE OF EC CERT .(AND ADD END DATE - WHEN EC CERT . VALIDITY ENDS ,OR WHEN DEVICE CEASES TO BE MARKETED , OR WHEN NB IS CHANGED )P LACE , D ATE OF D ECLARATION :CITY , DATES IGNATURE :____________________NAME :POSITION : (RESPONSIBLE S ENIOR E XECUTIVE OF MANUFACTURER )。
欧盟符合性声明模板
欧盟符合性声明模板EU DECLARATION OF CONFORMITY (No XXXX)欧盟符合性声明（No XXXX ）1. Pressure equipment or assembly (product, type, batch or serial number):1、压力设备或组合件（产品，类型，批号或序列号）：2. Name and address of the manufacturer and, where applicable, his authorised representative:2、制造商的名称和地址，以及他的授权代表（如适用）：3. This declaration of conformity is issued under the sole responsibility of the manufacturer.3、制造商自行负责制定本符合性声明。
4. Object of the declaration (identification of pressure equipment or assembly allowingtraceability; it may, where necessary for the identification of the pressure equipment or assembly, include an image):4、声明的对象（具有可追溯性的压力设备或组合件标识；当有必要识别压力设备或组合件时，它可以包含图片）：—description of the pressure equipment or assembly, ——压力设备或组合件的描述，—conformity assessment procedure followed,——合格评定程序，—in the case of assemblies, description of the pressure equipment constituting the assembly,and the conformity assessment procedures followed, ——在组合件的情况下，描述构成组合件的压力设备以及合格评定程序，5. The object of the declaration described above is in conformity with the relevant Unionharmonisation legislation:5、以上声明目的是满足相关欧盟协调法规：6. References to the relevant harmonised standards used or references to the other technical specifications in relation to which conformity is declared:6、引用使用的相关协调标准，或引用符合性声明相关的其他技术文件：7. Where appropriate, the name, address and number of the notified body which carried out the conformity assessment and the number of the certificate issued, and a reference to the EU-type examination certificate –production type, EU-type examination certificate –design type, EU design examination certificate or certificate of conformity.7、当合适时，进行合格评定公告机构的名称、地址和编号和颁发证书的编号，以及引用欧盟型式检验证书—生产型，型式检验证书—设计型，或符合性证书。
CE_Declaration_of_Conformity
Original Declaration of Incorporation of PartlyCompleted Machinery (EC Directive 2006/42/EC) and EC Declaration of Conformity in compliance with theDirectives on EMC and Low VoltageSIPOS Aktorik GmbH as manufacturer declares herewith, that the above mentioned electric actuators meet the following basic requirements of the EC Machinery Directive 2006/42/EC: Annex I, articles 1.1.2, 1.1.3,1.1.5, 1.2.1; 1.2.6, 1.3.1, 1.3.7, 1.5.1, 1.6.3, 1.7.1, 1.7.3, 1.7.4.Manufacturer:SIPOS Aktorik GmbH, Im Erlet 2, 90518 Altdorf, Germany Type of product:Electric actuator Authorised personfor documentation:Dr. Matthias Rebhan, Im Erlet 2, 90518 Altdorf, Germany Type range: 2SA5..., 2SB5..., 2SC5..., 2SG5…The product complies with the following harmonised standards with respect to the EC Machinery Directive: EN 12100-1: 2003 EN 12100-2: 2003 EN 60204-1: 2006Furthermore the following safety relevant standards are regarded:ISO 5210: 1996 ISO 5211: 2001 DIN 3358: 1982With regard to the partly completed machinery, the manufacturer commits to submitting the documents to the competent national authority via electronic transmission upon request. The relevant technical documentation pertaining to the machinery described in Annex VII, part B has been prepared.SIPOS actuators are designed to be installed on industrial valves. SIPOS actuators must not be put into service until the final machinery into which they are to be incorporated has been declared in conformity with the provisions of the EC Directive 2006/42/EC.As partly completed machinery, the actuators further comply with the requirements of the following directives and the respective approximation of national laws as well as the respective harmonised standards as listed below:• Directive relating to Electromagnetic Compatibility (EMC) (2004/108/EC):EN 61800-3: 2005• Low Voltage Directive (2006/95/EC):EN 60204-1: 2006 EN 60034-1: 2004 EN 50178: 1997 EN 61010-1: 2001Year of affixing of the CE marking: 2010 Altdorf, 29.12.2009This declaration does not contain any guarantees. The safety instructions in product documentation supplied with the devices must be observed. Non-concerted modification of the devices voids this declaration.Dr. Matthias RebhanGeneral ManagerY070.154/GB。
TUV符合性声明样稿(中英文)
Declaration of ConformityManufacturer: ABC Medical Devices Co., Ltd.No.107, Super Road, Sanya, 530012, ChinaEuropean ZYX Regulatory Affair Service Co., Ltd.Representative: Str. UbRtse, Berlin, D-09856, GermanyProduct Name: Patient MonitorModel Number: P20, P22 and P24 (Start from S/N 04100001)UMDNS Code: 16484Classification (MDD, Annex IX): IIb, rule 10Conformity Assessment Route: Annex II.3We herewith declare that the above mentioned products meet the transposition into national law, the provisions of the following EC Council Directives and Standards. All supporting documentations are retained under the premises of the manufacturer.符合性声明制造商：XX医疗器械公司XX地址欧盟代表：XX 地址产品名称：XX产品编号：XX欧盟通用医疗器械编号（UMDNS Code:）：XX分级（按照MDD的分级）：XX符合性评估依据：XX我们宣告以上提到的医疗器械符合国际法律法规，欧盟的医疗器械指令和标准。
所有的文档都以制造商为前提进行保存。
DIRECTIVESGeneral applicable directives:Medical Device Directive: COUNCIL DIRECTIVE 93/42/EEC of 14 June 1993 concerning medical devices (MDD 93/42/EEC). Amended by DIRECTIVE 2007/47/EC of 5 September 2007Standard Applied:EN980:2008 EN1041:2008 EN ISO 13485:2003/AC:2007EN ISO 14971:2007 EN 60601-1:1990+A1+A2 EN 60601-1-1:2001EN 60601-1-2:2001 EN 60601-2-49:2001 EN 60601-1-6:2004指令主要适用标准：医疗器械指令：1993年6月14日有关医疗器械的指令，标准委员会93/42/EEC2007年9月5日修订2007/47/EEC引用标准：EN980:2008 医疗器械标签中使用的图形符号EN1041:2008医疗器械厂商提供的信息EN ISO 13485:2003/AC:2007欧盟医疗器械法规（欧盟根据ISO13485等同转化的）EN ISO 14971:2007 医疗器械—医疗器械风险管理的应用要求EN 60601-1:1990+A1+A2 欧盟市场协调标准电子医疗器械安全性通用规则附件A1+A2 EN 60601-1-1:2001医用电气设备第1-1部分:安全通用要求并列标准:医用电气系统的安全要求EN 60601-1-2:2001 医用电气设备第1-2部分：安全通用要求并列标准：电磁兼容性要求和试验EN 60601-2-49:2001医用电气设备第2-49部分：多功能病人监护设备安全的特殊要求EN 60601-1-6:2004医用电气设备.第1-6部分:安全的通用要求Notified Body: TÜV SÜD Product Service GmbH, Ridlerstr. 65, 80339MÜnchen, GermanyNB Identification number: 0123(EC) Certificate(s): G1 09 06 88888 66Expire date of the Certificate: 2014-06-30Start of CE Marking: 2009-10-01Place, Date of Issue: Sanya, 2009-06-01Signature: __________________________Name: Bill GatesPosition: General Manager公告机构：TÜV SÜD公告机构识别号：0123（TUV南德意志集团）CE证书编号：XX证书有效期：XXCE标志开始有效日期：XX地点，生效日期：XX签名XX姓名：XX职位：XX。
格兰富CR安装使用说明书
举例
图 2 说明一台 EFF 1 电机在环境温度为 70 °C 时其电机负荷不得超 过额定输出的 89 %。如果水泵的安装高度超过海拔 4750 米，则电 机的负荷亦不得超过额定输出的 89 %。
如果最大温度和最大海拔高度同时超过允许范围，则降额指数应该 相乘 (0.89 x 0.89 = 0.79)。
4
Start the pump and check the direction of rotation.
6
Continue to vent the pump. At the same time, open the discharge isolating valve a little more.
8
For further information, see page 21.
举例
型号 : CR, CRI, CRN 额定流量 , 单位 m3/h 叶轮数 泵的版本代码 水泵管道连接代码 材料代码 水泵橡胶部件代码 轴封代码
CR 3- 10 X- X- X- X- XXXX
3.2 CR, CRN 32, 45, 64, 90, 120 和 150 型号名称说明
举例
泵型范围 : CR, CRN 额定流量 , 单位 m3/h 级数 小直径叶轮数 泵的版本代码 水泵管道连接代码 材料代码 水泵橡胶部件代码 轴封代码
23
7.5 变频器操作
23
8. 启动
23
9. 保养
24
10. 霜冻防护
24
11. 服务
24
11.1 服务套件和服务手册
24
12. 故障排除表
25
13. 报废处理
25
警告
装机前，先仔细阅读安装运行指导手册。 安装和运行 必须遵守当地规章制度并符合公认的良好操作习惯。
EC符合性声明
Disposable Syringes with Needles
Model:0.5ml、1ml、2ml、2.5ml、3ml、5ml、6ml、10ml、20ml、30ml、50ml、60ml
UMDNS-Code：13929
of class:
Ⅱa
according to annex IX of directive 93/42/EEC /
EC DECLARATION OF CONFORMITY
Document number / version : HJ-CETF-D-03/B
Name and address of the manufacturer:
We declare under our sole responsibility that
Conformity aective 93/42/EEC Annex V,
Registration No.:
DD 60093887 0001
TüV Rheinland LGA Products GmbH
Notified Body: / Tillystra?e 2
90431 Nürnberg
Deutschland
CE 0197
_________________________ ______________________________
Place, date Name and function
ec符合性声明 ecdeclaration conformitydocument number hj-cetf-d-03/bname manufacturer:we declare under our sole responsibi li ty medicaldevice: disposable syringes wi th needles model: 3ml,5ml 60mlumdns-code: 13929 according annexix directive 93/42/eec provisions directive 93/42/eec tstranspositi ons national laws which apply "finalinspection report conformity assessment procedure: directive93/42/eec annex dd0001 rheinland lga products gmbh notified body: tillystra 90431nrnberg deutschland ce 0197 place,date name 2e9431583b 分享于 2021-07-21 16:43:10.0 ec符合性声明 文档格式: .doc 文档页数: 2页 文档大小: 38.5k 文档热度: 文档分类: 幼儿/小学教育 -- 教育管理 文档标签: ec符合性声明
DOC模板 - EU Declaration of Conformity 2015-06-15
符合性（自我）声明 - 针对EMC按符合性评定模式A进行评估的电子产品
需要更新为最新版的指令，
例如EMC 为2014/30/
EU，LVD为2014/35/EU.
符合性声明 - 针对已获得由公共机构出具EMC报告/证书的电子产品
需要更新为最新版的指令，
例如EMC 为2014/30/
EU，LVD为2014/35/EU.
符合性（自我）声明 - 针对在MD指令附录IV之外且按符合性评定模式A进行评估的机械产品
需要更新为最新版的指令，
例如EMC 为2014/30/
EU，LVD为2014/35/
EU，MD为2006/42/EC.
符合性声明 - 针对已获得由公告机构EMC报告/证书，且在MD指令附录IV之外且按符合性评定模式A进行评估的机械产品
需要更新为最新版的指令，
例如EMC 为2014/30/
EU，LVD为2014/35/
EU，MD为2006/42/EC.。