铸造学专业英语词汇
铸造实用词汇(中英文)
1. charging mixture (配料)2. gas vent (通气孔)air vent (通气孔)3. alcohol base wash (酒精基涂模剂)4. alloy (合金)alloy cast iron (合金铸铁)5. anchor pin (定位销)6. annealing (退火)annealing furnace (退火炉)7. arc welding (电弧熔接)8. as cast (铸胚/毛胚铸件)9. atmospheric core / pencil core(砂心/ 增压/透气砂心)10. bath analysis (炉前分析)11. hand molding (手工造模)12. bending strength (抗弯强度)13. bending test (弯曲试验)14. binder (黏结剂)15. furan resin 夫喃树脂16. blow hole / gas hole (气孔) 17. Brinell hardness (布氏硬度)18. brittleness (脆性)19. broken casting at gate / riser or vent(铸件破损) 去除浇口, 冒口, 溢流口时 , 一起将铸件主体部分也去除的破坏缺陷20. case hardening (表面硬化)21. pouring / pour / cast (浇铸/浇注)22. castability (铸造性)23. casting design / casting plan ( 铸造方案)24. cast iron / iron castings (铸铁)25. cavity (缩孔)26. ceramic core (陶瓷砂心)27. ceramic filter (陶瓷过滤片)28. ceramic tube (陶管)29. chaplet (砂心撑)30. chill (冷硬/冷激)31. chiller / densener (冷铁)32. chunky graphite (块状/短小石墨)33. clay (黏土)34. riser(冒口)35. coat/mold wash/facing material (涂料/涂模剂)36. washing / coating (涂模/上涂料)37. cold junction (冷接点)38. composites / composite material ( 复合材料)sand mill / sand mixer ( 混砂机)sand mixing (练砂)sand mold (砂模)39. contraction / shrinkage (收缩/缩孔/疏松)40. conveyor (输送机)41. core assemble (组合砂心)44. core box (砂心盒)45. core grid / rodding ( 砂心骨)46. core making machine ( 砂心机)47. lifting / raised mold / core raise ( 砂心上浮)48. core washing (砂心涂料)49. corrosion (腐蚀)50. crack (裂痕)=龟裂51. crystal (晶体)52. curing (硬化)53. cut (冲砂)=冲蚀54. metallic pattern (金属模)55. galvanizing (镀锌)56 . dirt / scum / dross / slag ( 熔渣 / 浮渣 / 炉渣)57. sprue / down sprue / down gate (下浇道 /竖浇道)58. draft (拔模斜度)59. drag (下模/下砂箱/下模箱)60. dressing / cleaning (上涂料/涂料/清理)61. electric furnace (电炉)62. electron microscope (电子显微镜)63. elongation (伸长/伸长率)64. etching solution/etching agent/etchingreagent (浸蚀液)65. open shrinkage / external shrinkage (外缩孔)66. ferritic spheroidal graphite cast iron(肥粒体球状石墨铸铁)67. ferrite (肥粒铁) 68. machining allowance / finishing allowance(加工余量)69. flake graphite cast iron ( 片状石墨铸铁)70. flow chart (流程图)71. CE meter (热分析)72. full size /full dimension (全尺寸)73. graphitic carbon / graphite carbon ( 石墨碳)74. gray cast iron (灰口铸铁/普通铸铁/片状石墨铸铁)75. green sand mold (湿砂模)76. hardener / hardening agent ( 硬化剂)77. hardness test (硬度试验)78. high frequency electric induction furnace ( 高周波感应电炉)79. holding furnace (保温炉)80. impact test (冲击试验)81. Charpy impact test (夏比冲击试验)82. impact value (冲击值)83. indirect chiller (间接冷铁)84. inlet / pouring basin / pouring cup ( 浇杯)85. Inoculant (接种剂)86. Inoculation (接种)87. ladle (浇包/浇桶/铁水包)88. molding flask (砂箱)89. joint surface (合模面)90. keel block (Y 型试块)91. knock-out / shake-out (清箱/开箱)92. low frequency induction furnace ( 低周波感应电炉)93. liquid penetrant testing (渗透探伤试验/PTtest)94. low temperature annealing ( 低温退火)95. magnetic powder test (MT/ 磁粉探伤)96. melting furnace (熔解炉)97. metal flask (金属砂箱)98. metallographic microscope ( 金相显微镜)99. metallography (金相学)100. parting line (分模线).101. parting plane (分割面)102. pattern (模型/模具)103. pattern coating (模型涂漆)104. pearlite (波来铁)105. burn on / sand burning ( 烧结/结砂) 106. pig iron (生铁)107. scrap steel (废钢)108. pin hole (针孔)109. pore (气孔)110. porosity (多孔性/气孔率)111. pouring rate (浇铸速度)112. pouring temperature (浇注温度)113. pouring time ( 浇注时间)114. pouring weight ( 浇注重量)115. quality control ( 质量管理)116. X-ray inspection / radiography (X 线探伤) 117. rapping (起模)118. ratio of graphite spheroidization ( 球化率) 119. rejected castings (不良品)120. residual stress (残留应力/铸造应力) 121. roll over machine ( 翻转机)122. sag core (砂心下垂) 123. sand blast (喷砂)124. sand inclusion ( 夹砂)125. short pours / short run ( 浇注不足)126. shot blast (抛丸)127. shrinkage cavity ( 缩孔)128. shrinkage crack (缩裂)129.slag off agent / slag disposal agent ( 除渣剂)130.slag inclusion (夹渣)131.solidification time (凝固时间)132.spherodial graphite (球状石墨)133.spheroidizing agent (球化剂)134. strength test (强度试验)135. stress concentration ( 应力集中)136. stress relief (应力消除)137. rough surface (表面粗糙)138. surface fold / gas run ( 皱皮/流缝/冷隔)139. surface roughness ( 表面粗糙度)140. surface treatment ( 表面处理)141. tensile strength ( 抗拉强度)142. tensile test (拉伸试验)143. test piece/test lug ( 试片)144. used sand (旧砂)145. working reference point ( 加工基准)146. Ultrasonic testing (UT/超声波检测)147. Gating system (浇注系统)148. test coupon (试棒)149. Non-destructive testing (NDT/非破坏性测试)150. Visual inspection (VT/ 目测)151. rough machining (粗加工)152. finishing machining (精加工)153. Non conformity report (NCR 不符合报告)154. Corrective action report ( 改善措施报告)155. solidification simulation ( 凝固模拟)。
铸造专业英语
铸造学专业英语词汇暗冒口 blind feeder暗冒口 blind head暗冒口 blind riser暗冒口 bob暗冒口 closed riser盎司合金(85-5-5-5铜合金) ounce metal凹口 notch凹口半径 radius of notch凹口感度 notch sensibility凹口试片 notch bar凹口试片 notched bar凹口作用 notch effect凹陷(铸疵) sink head巴氏合金 Babbitt metal扒炉渣 raking out the slag扒渣 slagging off扒渣 slag-off扒渣，结渣 slagging拔模螺丝 pattem screw拔模斜度 pattern draft钯(Pd) palladium白[口]生铁 white pig iron白[口]铸铁 white cast iron白[口]铸铁 white iron柏努利定理Bernoulli's theorem柏思麦酸性转炉生铁 Bessemer pig iron柏思麦转炉 Bessemer converter摆m线(造模) storing line斑面(铸疵) pitting surface斑蚀，点食 pitting搬运，手操作 handling板 board板片捆 sheet pack板手 spanner板条结构模型 grounds and lags板条输送机 slat conveyor半合成模砂 semi-compounded molding sand 半焦 semi-coke半径 radius半静钢 semi-killed steel半离心铸造法 semi-centrifugal casting 半龙门起重机 semi-goliath crane半圈补给口 half-feeder半熔未型撑 unfused chaplet 半软钢 semi-mild steel半硬钢 medium hard steel半永久铸模 semi-permanent mold棒磨粉机 bar mill棒状砂心 slab core磅/平方吋 PSI(1bs per square in)包晶变态 peritectic transformation包晶反应 peritectic reaction包曼试验 Baumann test包模涂料 precoating material包模造模法 investment molding包模铸造法 investment casting包贴 en-casement包析 peritectoid包析反应 peritectoid reaction剥落 spall剥落 spalling剥落，剥皮 peeling剥砂痕(铸疵) rat tail剥砂面(铸疵) buckle剥砂线(铸疵) sand kneader保持时间 holding time保持温度 holding temperature保磁力 coercive force保护蒙气 protective atmosphere保护手套 protective glove保温电力 holding power保温净化，焖热，均热 soaking保温净化，焖热烧透均热 stewing保温炉 holding furnace保温炉 receiving furnace保险杠，缓冲器 bumper保证试验 proof test饱和度 degree of saturation饱和度 saturatin degree爆炸状石墨 exploded graphite贝他黄铜 beta(B)brass贝他石墨 beta(B)graphite贝他铁 beta(B) iron背板 backpa backplate，die cast背板榇砂造模法 back plate molding背层泥浆 back-up coating slurry背砂 back sand，back-up-sand背砂 backing sand背压 back pressure备用砂心条 stock core钡(Ba) barium本智周万物夹渣(由金属本身引成) endogenousslag inclusion畚箕，篮 basket崩散 collapse崩散性 collapsibility绷索 rope比电阻 specific resistance比例碱度 proportional basicity比例限界 limit of proportionality比例限界 proportional limit比热 specific heat比色定量分析 colorimetric analysis比色定量学 colorimetry比色高温计 color comparator pyrometerA.F.S.粒度指数 A.F.S grain fineness numberASTM弯曲试杆 arbituration barA型石黑 A type graphtieB型石墨 B type graphite1. 铸件后处理 (post treatment of casting) [ 铸件 ] 对清理后的铸件进行热处理﹑整形﹑防锈处理和粗加工的过程。
铸造学专业英语词汇
铸造学专业英语词汇铸造学专业英语词汇铸造是人类掌握比较早的一种金属热加工工艺，已有约6000年的历史。
以下是为大家分享的铸造学专业英语词汇，供大家参考借鉴，欢迎浏览!碱性熔铁炉 basic cupola碱性熔渣 basic slag碱性生铁 basic pig iron碱性氧化物 basic oxide碱性氧气吹炼法 basic oxygen process碱性造渣法 basic slag practice碱性砖 basic brick渐进时效 progressive aging键形进模口 key gate溅铁 iron spillage僵土 dead clay浆 slurry降伏点，屈服点 yield point降伏强度 yield strength交流电精密仪器接机 alternate current welder交替浸渍试验 alternate immersion test焦[炭]头 ashy top焦块粒度 coke size焦炭比，煤焦比 coke ratio焦炭粉，煤焦粉 coke powder焦炭炉，煤焦炉 coke furnace焦炭生铁，煤焦生铁 coke pig iron焦油 tar焦油白云石砖 tar dolomite brick浇杯 pouring cup浇池 pouring basin浇出嘴(斗、桶、埚、炉） pouring lip浇道 pouring gate浇道棒 runner stick浇道比 runner ratio浇道废料 runner scrap浇道接种法 mold inoculation浇道系连结模型 pattern incorporating the runner system 浇道砖 cluster bottom mold，runner core浇斗，糊料 ladle cement浇斗，浇桶，盛桶 ladle浇斗柄，浇斗抬架 shank浇斗车 ladle car浇斗车 ladle on wheels浇斗抬架 ladle carrier浇斗嘴 lip浇斗，浇桶 pouring ladle浇斗覆盖草灰 limmer浇斗瞬间接种法 instantaneous ladle inoculation浇口，进模口 gate浇口棒 gate stick浇口杯 sprue cup浇口发热剂 pouring gate feeding compound 浇口剖面积，进模口剖面积 gate area浇口切断 gate cutting浇口切断 sprne shearing浇口切断机 gate cutter浇口切断机 gate cutting machine浇口套筒(压铸) sprue bush浇口箱 runner box浇流系方案 gating system plan浇流系统 gating system浇满 gating with run-of浇冒口布置 running and feeding layout浇冒口方案(美) gating and risering(us)浇冒口方案(英) gating and feeding(gb)浇冒口切断机 sprue cutter浇冒口系统 running and feeding system浇皿，浇碟 pouring dish浇套，浇杯 pouring bush浇桶 foundry ladle浇桶(半)取样 ladle sampling浇桶(斗)车 ladle bogie浇桶(斗)挂起梁 ladle bail浇桶(斗)架 ladle chair"浇桶(斗)浇完时间 ladle emptying time浇桶(斗)浇完时间 ladle pouring time浇桶(斗)取样分析 ladle analysis浇桶(斗)容量 ladle capacity浇桶(斗)剩料 ladle residues浇桶(斗)试验 ladle ttest浇桶(斗)抬架 ladle shank浇桶(斗)液面遮盖 ladle covering compound浇桶(斗)预热器 ladle preheater浇桶(斗)嘴 ladle lip浇桶粑 skull浇桶吊车 ladle crane浇桶接种法，浇斗接种法，取熇接种法吊 ladle inoculation 浇桶抬架 carrying tongs浇桶置冲法 open ladle method浇桶砖 ladle brick浇桶转浇 reladle浇铸(浇钢锭) teeming浇铸，浇注 pouring浇铸不到(铸疵) short run浇铸不足(铸疵) poured short浇铸不足(铸疵) short pours浇铸操作 pouring operation浇铸过程 casting cycle浇铸区 casting area浇铸区 casting bay浇铸设备 casting equipment浇铸时间 casting time浇铸时间 pouring time浇铸速率 casting rate。
铸造学专业英语词汇[1]
![铸造学专业英语词汇[1]](https://img.taocdn.com/s3/m/64d36cf6998fcc22bdd10d08.png)
铸造学专业英语词汇(1)A.F.S.粒度指数 A.F.S grain fineness numberASTM弯曲试杆 arbituration barA型石黑 A type graphtieB型石墨 B type graphiteCO2造模法，二气化碳造模法 CO2 process，carbon dioxide processDM转炉 DM converterF.S.造模法，流砂造模法 F.S.process，fluid sand mixture molding process F-M造模法，全模法 F-M process，full-mold processLD(转炉盗氧炼钢)法 LD processLD转炉 LD converterL形吊骨 jaggerN造模法，西山氏硬化法 N-ProcessPH值，离标值 pH valueSAE钢 SAE steelS形钩 S hookX光(X射线)，检验 X-ray inspectionX光(X射线)，绕射线 X-ray diffraction methodX光(X射线)，透视法 X-ray radiographyX光(X射线)，显微分析器 X-ray microanalyserX光，X射线 X-rayX脱模法(包模铸造法)(三氯乙烯蒸气脱蜡) X-processY合金 Y-alloy阿达麦辊 Adamite roll阿伐固溶体 alpha(a)solid solution阿伐黄铜 alpha(a)brass阿伐青铜 alpha(a)bronze阿伐铁 alpha(a)iron阿姆可铁，工业级纯铁 Armco iron埃(10-10米) Angstron unit埃鲁电弧炉 Heroult electric arc furance艾氏冲击试验 Izod impact test艾氏冲击试验机 Izod impact testing machine艾素丘法 Isocure process爱玛炉(碳化硅电阻炉) Elema furnace安定化退火 stabilizing anneal安全布置 safety layout安全护目镜 safety goggles安全帽 helmet安全设施 protection and safety equipment安全限应力 proof stress安全楔 safety wedge岸砂 shore sand按钮选择 push button selection胺基甲酸乙脂 urgthane胺类 amine胺气 amine gas暗冒口 blind feeder暗冒口 blind head暗冒口 blind riser暗冒口 bob暗冒口 closed riser盎司合金(85-5-5-5铜合金) ounce metal凹口 notch凹口半径 radius of notch凹口感度 notch sensibility凹口试片 notch bar凹口试片 notched bar凹口作用 notch effect凹陷(铸疵) sink head巴氏合金 Babbitt metal扒炉渣 raking out the slag扒渣 slagging off扒渣 slag-off扒渣，结渣 slagging拔模螺丝 pattem screw拔模斜度 pattern draft钯(Pd) palladium白[口]生铁 white pig iron白[口]铸铁 white cast iron白[口]铸铁 white iron白粉料(涂模用) white facing白合金 white metal白金，铂(Pt) platinum白黏土 white clay白铁皮，锌板 zinc plate白心展性铸铁(白心可锻铸铁) white heart malleable cast iron 白杨木 poplar白缘(黑心展性铸铁) pearlite rim白云，母石黏土 illite clay白云石 dolomite白云石 magnesia limestone白云石砖 dolomite brick百万分之一 ppm柏努利定理 Bernoulli's theorem柏思麦酸性转炉生铁 Bessemer pig iron柏思麦转炉 Bessemer converter摆m线(造模) storing line斑面(铸疵) pitting surface斑蚀，点食 pitting搬运，手操作 handling板 board板片捆 sheet pack板手 spanner板条结构模型 grounds and lags板条输送机 slat conveyor半合成模砂 semi-compounded molding sand 半焦 semi-coke半径 radius半静钢 semi-killed steel半离心铸造法 semi-centrifugal casting 半龙门起重机 semi-goliath crane半圈补给口 half-feeder半熔未型撑 unfused chaplet半软钢 semi-mild steel半硬钢 medium hard steel半永久铸模 semi-permanent mold棒磨粉机 bar mill棒状砂心 slab core磅/平方吋 PSI(1bs per square in)包晶变态 peritectic transformation包晶反应 peritectic reaction包曼试验 Baumann test包模涂料 precoating material包模造模法 investment molding包模铸造法 investment casting包贴 en-casement包析 peritectoid包析反应 peritectoid reaction剥落 spall剥落 spalling剥落，剥皮 peeling剥砂痕(铸疵) rat tail剥砂面(铸疵) buckle剥砂线(铸疵) sand kneader保持时间 holding time保持温度 holding temperature保磁力 coercive force保护蒙气 protective atmosphere保护手套 protective glove保温电力 holding power保温净化，焖热，均热 soaking保温净化，焖热烧透均热 stewing保温炉 holding furnace保温炉 receiving furnace保险杠，缓冲器 bumper保证试验 proof test饱和度 degree of saturation饱和度 saturatin degree爆炸状石墨 exploded graphite贝他黄铜 beta(B)brass贝他石墨 beta(B)graphite贝他铁 beta(B) iron背板 backpa backplate，die cast背板榇砂造模法 back plate molding背层泥浆 back-up coating slurry背砂 back sand，back-up-sand背砂 backing sand背压 back pressure备用砂心条 stock core钡(Ba) barium本智周万物夹渣(由金属本身引成) endogenous slag inclusion 畚箕，篮 basket崩散 collapse崩散性 collapsibility绷索 rope比电阻 specific resistance比例碱度 proportional basicity比例限界 limit of proportionality比例限界 proportional limit比热 specific heat比色定量分析 colorimetric analysis比色定量学 colorimetry比色高温计 color comparator pyrometer铸造学专业英语词汇(2)铸造学专业英语词汇(2)比色计colorimeter比色温度color temperature比重specific gravity闭附气occluded gas铋(Bi) bismuth边材(木材) sap wood边线，轮缘，胎环rim边线效果eddge effect边续式台车轮模机car type mold conveyor扁块，平板slab扁刷flat brush扁形进模口flat gate扁凿flat chisel变<<hap003>>铁，变<<hap003>>体bainite变态transformation变态[温度]范围transformation range变态点transformation point变态温度transformation temperature变态温度transition temperature变态温度范围transformation temperature range 变形deformation变形模型distoted pattern变形铸件strained castings变质剂leavening agent杓dipper杓，小铲scoop标称定律nominal rating标称应力nominal stress标称直径nominal diameter标称资本nominal capital标点gage point标点(抗拉试样) gage mark标距gage length标准成分，标准分析法standard analysis标准模型standard pattern标准砂standard sand标准试样standard sample标准预测值normal expected value标准圆筒试样(模砂) standard cylindrical specimen 标准砖standard square[bick]表面保护surface protection表面处理surface treatment表面粗糙(铸疵) rough surface表面浮松(铸疵) scum defect表面光制surface finish表面烘干skin drying表面烘干模skin dried mold表面烘干砂模flared mold表面烘干砂模roast sand mold表面冷硬surface chill表面烧着furface vitrification表面硬化case hardening表面硬化surface hardening表面针孔(铸疵) surface pinholes冰晶石cryolite冰糖形断面(铸疵) rock candy[fracture]丙铜acetone丙烯树脂acrylic resin并流parallel flow波来铁，波来体pearlite波来铁展性(可锻)铸铁pearlite malleable iron 波来铸铁pearlite cast iron波美Baume波美比重计Baume's hydrometer波纹ripple玻璃过滤器glass fabric filter玻璃化virtrification玻璃纤维glass fiber玻璃纤维布glass cloth勃氏硬度Brinell hardness勃氏硬度试验Brinell hardness test薄壁铸件thin section castings薄壁铸件thin-wall cstings薄型砖split brick捕尘器arrester补偿导线compensation lead补充焦coke booster补充焦炭，补充煤焦extra coke补给，进料，补浇feed补给环feed ring补给距离feeding distance补给口(冒口) feeder补给口带feeding zone补给口发热剂exothermic feeding compound 补给口发热剂(冒口) feeding compound补给口套feeder bush补给口效果feeder effect补给用冒口feed riser补浇repouring补强带，炉箍strengthening band补绕(冒口) feeding补缀，补修，补修料patch补缀，补修，搪补patching不规则合模面irregular joint不规则形分模面stepped joint不合尺寸off-dimension不良件数，退件数rejection number不良品rejects不良铸造faulty casting不列颠合金Britania metal不熔[化]性infusibility不透气性impermeability不稳定平衡图unstable equilibrium diagram 不锈钢stainless steel部分还原铁矿partially reduced iron ore部分混合性partial miscibility部分模型department pattern擦光buffing擦光机buffing machine擦光剂buffing compound擦光轮buff擦光轮buffing wheel擦伤galling材料试验material test材料试验material testing材料试验机material testing machine采购部purchase department采购价，原价purchase price踩紧track tramping参考分析reference analysis参数parameter残磁residual magnetism残留波来铁residual pearlite残留尘量residual dust content残留磁气remanent magnetism残留活斯田铁retained austenite残留金属液remaining melt残留强度(铸砂) retained strength(sand)残留物residue残留物，筛留物residues残留雪明碳铁residual cementite残留应变residual strain残留应力residual stress仓bin仓储storage仓库store house操作，作业operation操作钮operating knob糙斑铁，糙斑体sorbite糙斑铁铸铁sorbitic cast iron槽(槽型炉) loop槽带输送机trough conveyor槽形感觉电炉channel typee induction furance 草绳braided straw草绳straw rope草图sketching侧流道side runner侧冒口side riser侧装机side loader测高温学pyrometry测厚黏土thickness piece测深尺depth scale测深规depth gage测微放射线像microradiography测温漆thermal paint测隙规，厚度规thickness gage层，片lamella层焦coke charge层流laminar flow层状波来铁laminar pearlite层状腐蚀lamellar corrosion插模钉sprag查马克(商品名，压帮用锌铝铜合金) Zamak 茶壶嘴式浇斗tea pot spout ladle搀炉，秋千炉，倾转熔铁炉tilting cupola 铲，砂铲shovel铲斗shovel loader长柄导杆long shaft pendulum tool长抹刀，柳叶抹刀long spatula长石feldspar长统手套gauntlet glove长焰煤long flame coal长凿long chisel常态分布normal distribution铸造学专业英语词汇(3)常温裹贴法cold coated process常温试验cold test常温自硬air setting常温自硬法air set process常温自硬黏接剂air setting binder常温自硬树脂粘结风airbond常温自硬性合成树脂cold-hardening synthetic resin 常温自硬性黏结剂cold-setting binder常温自硬油air setting oil常温自硬铸造模air setting mold场内熔接shop weld敞模，露天模open mold敞模铸造open sand casting敞砂模open sand mold敞砂模法open sand molding超高电力super-high power超轻合金ultra-light alloy超细粉sub-sieve powder超音波检验ultra-sonic testing车car车床lathe车床床身，车床床台lathe bed车屑turning scraps车屑turnings尘量测定器dust extraction device榇边bush，bushing榇垫，填料packing榇炉用期lining campaign榇砖lining brick成本cost成本prime cost成长rowth成堆比重bulk specific gravity成堆密度bulk density成堆容积bulk volume成孔期(电弧炉)，搪孔boring成模台(压铸) holding block成品量，产量output成品铸件区finished castings department成熟度degree of normality成形forming成形性forming property程序图routing routing diagram弛力退火stress relief annealing池，浴槽bath持久比endurance ratio持久试验endurance test持久性endurance匙形抹刀slicker spoon迟延装置delay screen尺，规则rule尺寸dimension尺寸安定性dimensional stability尺寸精度dimensional accuracy齿轮吊车浇geared crane ladle齿轮缘gear rim赤铁矿hematite赤铁矿生铁hematite pig iron，hematite iron赤杨木alder充氮nitrogen charge冲砂(铸疵) cut冲砂(铸疵) cuts冲砂(铸疵) cuts and washed冲砂(铸疵)，涂浆wash冲蚀erosion冲蚀结疤(铸疵) erosion scab冲板洗涤机impingement plate scrubber冲层stampings冲床，冲头punch冲击磨耗pounding wear冲击强度impact strength冲击式硬度试验机impact hardness testin machine 冲击试验impact test冲击试验机impact tester冲击速度striking velocity冲击值impact value冲孔废料punched scrap冲射射式集尘器impingement dust collector冲销drift冲屑punchings虫lac虫胶shellac抽取用皮带输送机draw off belt conveyor抽吸罩suction hood抽吸装置sucking-off plant抽烟气设备fume extraction equipment抽样sampling抽样规则sampling prescription抽样检验samplimg inspection稠渣sluggish slag出口outlet出模机构knock-out gear出气管(旋风集尘器) exit pipe出清(熔炉) depletion出铁tapping出铁杆tap out bar出铁杆tapping bar出铁口，流出孔tapping hole出铁口熔渣flux出铁口塞杆tap hole plug stick出铁温度tapping temperature出渣slag-out出渣，脱渣deslag，deslagging出渣槽slag notch出渣槽slag spout出渣槽slagging spout出渣孔scum hole出渣孔slag hole初步清理台rough dressing table初步试验preliminary test初级线圈primary air初加料，起熔料initial charge初晶primary constituent初晶活斯田铁proeutectic austenite 初晶石墨primary crystal初裂incipient crack初凝结initial condensation初生吐粒铁primary troostite除尘dedusting除尘dust extraction除尘器dust separator除尘设备dust removal除尘设备dust removal plant除尘装置dust separation plant除铝剂aluminium removal除气degasification除气degasifying除气degassing除气剂degasifier除气熔剂degassing flux除气退火degassing anneal除氢，脱氢degassing of fydrogen 除湿dehumidification除湿，脱水，干燥dehydration除湿器dehumidifier除渣drossing除脂degreasing储仓bunker储仓silo储仓storage bunker处理楔值processing wedge value处理用浇桶theatment ladle穿透，贯穿penetration穿透能力(X光试验) penetrating power船用钢板ship plate传导度conductivity传递气carrier gas传递液carrier fluid传热流体thermal fluid吹板(吹砂机) blow plate吹板(吹砂机) blowing plate吹疵blow吹风淬火air blast quenching吹管blow-pipe吹净用空气(冷厘法) scavening air吹气，通气处理(金属液)，冲洗flush slag 吹枪blow gun吹砂机(造砂心用) blowing machine吹氧炼钢法oxygen steel making吹氧嘴管oxygen lance吹制砂心blow a core吹制砂心blowing吹制砂心blown core吹制用砂心盒core box for blowing锤hammer锤鳞，鍜鳞hammer scale锤平，轻敲peening锤球，落锤球tup锤碎机hammer mill纯度degree of purity纯度purity纯铁pure iron瓷土，高岭土china clay铸造学专业英语词汇(4)磁粉探伤magnetic particle inspection，magnetic crack detection 磁化力magnetizing force磁力带轮(磁选机用) magnetic pulley磁力探伤magnzflux磁力探伤检验magnaflux inspection磁力探伤检验magnetic crack detection磁力筒(磁选机用) magnetic drum磁力造模法magnet molding process磁铁矿magnetite磁性变态magnetic transformation磁选机magnetic separator磁滞损失hysteresisloss枞木fir粗度，粗糙度roughness粗钢raw steel粗晶面(铸疵) facet tracture粗粮波来铁coarse pearlite粗面凝固rough wall solidification粗磨snag粗磨机rough grinding machine粗泥浆砂roughing loam粗砂coarse sand粗砂roughing sand粗砂锥辗硅砂concial sand from coarse sand粗筛riddle粗松组织coarse structure粗松组织open-grain structure粗铜blister copper粗轧辊roughing roll催化剂accelerator催化剂，触媒，冷化剂catalyst脆化embrittlement脆性brittleness脆性shortness淬火quenching淬火机hardening machine淬火裂痕quench crack淬火裂痕quenching crack淬火能力(淬火液) quenching intensity淬火时间quenching time淬火时效quench aging淬火应力quenching stress淬火硬化quench hardening淬裂hardening crack错模，偏合，毛边(铸疵)，工作班制shift错配(模型，铸模，心型) mismatch，in pottern mold，core 鎝(Tc) technetium打包机packer打孔卡片punch card打孔纸带puch tape打磨(磨毛边，打浇冒口等) fettle shagging打磨滚筒rattler打散筛孔breaker screen打铁球skull cracker打铣球，落锤drop ball大浇斗bulbs大气，蒙气(炉内气氛) atmosphere大气泡(铸疵) gross blowhole大气熔化air melting大气铸造air casting大型铸件large castings带band带，皮带belt带锯band saw带色防护镜filter glass带式磁选机magnetic belt separator带式运送机belt conveyor带铁fillet iron带缘导销collared pin带运送机band conveyor袋滤器bag filter袋滤器bag house袋形端承pocket print单边心型端承，单边砂心头single core print单轨系统monorail system单件模型one-piece pattern单面模型板single-strand casting machine单色光学高温计monochromatic optical pyrometer单体肥粒铁free ferrite单体碳free carbon单体雪明碳铁free cementite单条[连续]铸造机sink单位负载unit load单向凝固unidirectional solidification单元砂，整体砂unit sand单支进模口本堰single gate氮硬化nitrogen hardening氮(N) nitrogen氮化nitriding氮化法nitriding process弹动清砂spring release弹簧心型撑spring chaplet弹能模数modulus of resilience弹壳黄铜(三七黄铜) cartridge brass弹性elasticity弹性变形elastic deformation弹性模数，弹性系数elastic modulus弹性能resilience弹性切割砂轮elastic slitting wheel弹性系数，弹性模数modulus of elasticity 弹性限界elastic limit弹性限界limt of elasticity当量，等价系数coefficient of equivalent 挡板baffle挡板baffle plate挡板damper挡渣坝dam挡渣口浇桶dam type lip ladle档渣浇池pouring basin with buffles刀形进模口knife gate倒角，去角rounded sand grain捣成炉榇rammed lining捣成用料ramming compound捣动盛桶(脱硫用) shaking device捣紧，填塞剂tamping捣紧度，槌紧度degree of ramming捣砂，捣制rramming捣砂锤bench rammer捣砂锤rammer捣砂杆sand rammer捣砂走样ram off捣制砂心ram up core捣制走样ramaway导股(连续铸造) strand guiding导气管air duct导入，导件guide导套guide bushing导销guide pin导销leader pin导销榇套leader pin bushing得板screen plate德拉瓦离心铸管法De-lavaued processdelay relase德他固溶体dendrite德他合金delta solid solutin德他黄铜delta bronze德他青铜delta iron德他铁delta metal德银，铜German silver等吹熔铸炉equi-blast cupola等价因子equivalence factor等温变态isothermal transformation等温退火isothermal annealing等温线图isothermal diagram等温硬化isothermal hardening低合金钢铸件low alloy steel castings低磷生铁low phosphorus pig iron低摩擦金属anti-friction metal低黏天然砂meager sand低黏性砂lean sand低黏性砂weak sand低黏性硅砂，硅砂unbonded silica sand低碳钢low carbon steel低碳生铁low carbon pig iron低温脆性cold shortness低温熔化cold melt低温退火low temperature annealing低压风扇low pressure fan低周波main frequency低周波感应电炉line frequency induction furnace低周波感应电炉low frequency electric induction furance迪沙式自动造模机(丹麦制高压高速无箱式造模机) Disamatic molding machine 底(炉)，(造模) bed底板acking board底板bed plate底板bottom board底板bottom plate底层装料bed charge底焦coke bed底浇法bottom casting底浇法bottom pouring底浇式浇桶bottom pour ladle铸造学专业英语词汇(5)底浇铸模bottom pour mold底进模口法bottom gating底面basal plane底炭bed coke底炭高度bed coke height底特律式电弧炉Detroit electric furnace地坑pit地坑炉pit furnace地坑造模法pit molding地坑铸造pit casting地面砂，背砂floor sand地模floor mold地模法，地面造模法floor molding碲(Te) tellurium碘(I) iodine点火firing点火ignition点火ligh up点火lighting up点火light-off点火孔breast door点火孔lighting hole点火器igniter点燃点ignition point电池，组battery电磁搅拌electric magnetic agitation电磁循环electric magnetic circulation电动吊车electric hoist电动发电机motor generator电动加气硬化机automatic gassing machine 电动推高机electric lift truck电动造模机electric molding machine电镀electro-gilding电镀electro-plating电焊条，电熔接条arc welding electrode电弧长度arc length电弧截割arc cutting电弧炉arc furnace电弧炉electric arc furance电弧气吹铲平arc-air gouging电弧气吹切割arc-air cutting电弧熔接arc welding电弧熔接，电焊electric arc welding电极，电熔接条，电焊条electrode电极耗用量(电弧炉) electrode consumption电极夹具，电熔接条夹把，电焊条夹把electrode holder 电极控制系统electrode control system电极清洁法electrol-cleaning电极熔接，电极焊接electrode welding电极头stub end电解精炼electrolytic refining电解铁electrolytic iron电解铜electrolytic copper电解锌electroplytic zinc电开关装置electric switchgear电炼生铁electric furance iron电炉electric furance电炉钢electric steel电滤尘器electro-filter电木，胶木bakelite电热熔化electric smelting电子electron电子显微镜electron microscope电阻高温计resistance pyrometer电阻合金electro-resistance alloy电阻炉electric resistance furance电阻炉resistance furnace电阻系数，电阻力resistivity垫板，底板base plate垫厚(铸造技术) padding，reinforcement垫厚(铸造技术) reinforcement，paddling垫圈，洗涤机washer淀粉starch吊车hoist吊车浇桶crane ladle吊车盘hoist pan吊钩lifting hook吊骨，撑条，插条gagger吊骨，撑条，插条slodier吊骨，吊具，吊架hanger吊环bail吊梁lifting beam吊砂条clack吊运车trolley吊钩load hook吊骨anchoring调合模砂blended molding sand调节设备controlled means调辙车transfer car调整器regulator调质处理quenching with Subsequent tempering 调质砂tempering sand调质水分tempering water调质铸铁modified cast iron蝶形阀butterfly valve迭边浇道Connor runner bar迭边进模口kiss gate迭边进模口lap gate迭边冒口kiss riser迭模multiple mold迭模stack boxes迭模stack mold迭模法multiple molding迭模法stack molding迭模浇铸法stack pouring迭箱stack钉nail顶板ejection plate顶板lifting plate顶板top board顶板top plate顶出ejection顶出板(压铸) ejector plate顶出杆knock-out bar顶出力ejector force顶出器，喷射器ejector顶出销knock-out pin顶出销(压铸) ejector顶浇法top pouring顶浇进模口top gate顶冒口top riser顶销，起销lifting pin顶铸法top casting process定量分析quantitative analysis定量仪quantometer定模(压铸) cover die定模板(压铸)，平台platen定盘式混砂机fixed pan mill定时淬火time quenching定时器timer定位垫locating pad定位孔locating hole定位销locating pin定位销钉positioning dowel定位锥locating cones定心毂centering boss定心针centering pin定性分析qualitative analysis订货铸造工场jobbing foundry铥(TM) thulium冻汞法(精密铸造) Mercast process动力滚子输送机powered roller conveyor 动力试验dynamic test动叶轮impeller动叶轮摔砂impeller ramming动作，工作working都市煤气town gas陡震试验shock test斗，箕斗，桶装载机bucket毒性度toxicity rating读数式分光仪digital spectrometer堵口砖nozzle brick堵塞bott堵塞botting堵塞出铁口(熔铁炉) stopping up堵塞杆bott stick堵塞器stopper堵塞式浇桶stopper ladle堵塞砖stopper and nozzle brick杜具纳转炉Tropenas converter杜维利化碳转浇铸法Durville pouring杜维利化碳转浇铸法Durville process镀镍nickel plating镀锡铁皮，马口铁皮tin plate镀锌galvanizing镀锌sherardizing镀锌zinc coating镀锌zinc plating镀锌，浸锌zinc galvanizing镀锌脆性galvanizing embrittlement镀锌铁板，白铁皮galvanized iron sheet 镀锌铁皮，白铁皮zinc-coated sheet短暂退火炉short anneal furnace锻造用合金wrought alloy断口检验fracture test断口金相检验fractography断裂点point of rupture断面收缩necking断面缩率area contraction，percentage of 断面缩率area reduction，percentage of铸造学专业英语词汇(6)断续浇铸interrupted pouring堆heap堆高机fork lift truck堆积密度packing density堆料场stock ground堆料场stock-yard堆砂heap sand堆渣场slag tip堆重piled weight对合开放砂心盒split open ended core box 对合模型，分割模型split pattern对合模型板，分割模型板split plate对合铸模split mold对流convection对准alignment钝气inert gas钝气电弧熔接inert-gas arc welding多边形筛polygonal screen多段风口，多段风嘴multiple tuyere多角形砂angular sand多孔塞porous plug多孔塞搅拌法porous-plug method多孔性，气孔率，气孔巢(铸疵) porosity 多石英砂quartzose sand多水高岭土halloysite锇(Os) osmium鹅颈浇道，鹅颈管goose neck而酸铸铁acid resistant cast iron耳轴，挂耳trunnion二次风口，二次风嘴secondary tuyere二次合金secondary alloy二次空气secondary air二钙硬化法Di-Cal process二氧化锆zirconia二氧化碳造模法，碳酸气硬模法，CO2造模法carbon dioxide process(CO2 process) 二氧化铁(FeO2) ferrous oxide二元合金binary alloy发火合金pyrophoric alloys发热反应exothermic reaction发热覆盖?冒口用) exothermic shield发热冒口exothermic riser发热套筒exothermic sleeve发热性缩颈砂心(冒口用) exothermic breaker core发热性缩孔防止粉exothermic antipiping powder发生炉producer发生炉煤气power gas发生炉煤气producer gas发生炉燃气，瓦斯generator gas阀valve珐琅面，上釉glassy surface翻举装置rollover and lifting device翻模rolling over翻模板rollover board翻模板rollover plate翻箱索具beam and sling翻箱造模机rollover molding machine翻转(壳模制造) peel back翻转，翻模rollover翻转顶销脱模机turnover and pinlift machine翻转式砂心机rockover core making machine翻转脱模式造模机frame-rollover machine翻转脱模装置turn-draw device翻转造模机turnover molding machine钒(V) vanadium钒铁ferro-vanadium钒铸铁vanadium cast iron反复冲击试验repair反复横断冲击试验repeated impact test反喇叭形浇口reverse horn gate反射炉air furnace反射炉reverberatory furnace反跳硬度计scleroscope反跳硬度试验rebound hardness test反跳硬度试验scleroscope hardness test反斜度back draft反应带reaction zone反应度reactivity反应模斜度inverse draft反应速率rate of reaction反转起模draw on turnover方锉square file方解石calcite方向性凝固directional solidification防尘面具，口罩respirator防护套管protection tube防裂筋cracking strip防裂片，散热片cooling fin防蚀anti-corrosion防缩暗冒口shrink bob防缩剂，冒口保温用anti-piping compound防缩孔粉剂pipe eliminator防缩冒口shrink head防缩冒口shrinker防锈anti-rust防锈剂rust-preventing agent防锈涂层rust preventive coating放射线检验radiographic inspection放射线检验radiographic testing放射线透视radioscopy放射线照片radiographic film放射线照像术radiography放射性同位素radioactive isotope放样板lay out board放置器set-down device非磁性铸铁non-magnetic cast iron非焦性煤non-coking coal非金属夹杂物non-metallic inclusion非金属夹杂物sonims非均质组织heterogeneous structure非破坏试验non-destructive testing(NDT)非铁金属non-ferrous metal非氧化气孔(银白色气孔)(铸疵) unoxidized blowholes 飞边(铸件) feather飞边，闪光flash飞边清除flash removal飞边现象(合模或模裂形成) finning飞灰fluxing肥粒铁，肥粒体ferrite肥粒铸铁ferritic cast iron沸腾boil沸腾boiling沸腾期boiling period肺尘埃沉着病pneumoconiosis费德曼组织(金相) Widmannstaetten structure废(钢)片sheet scrap废电极electrode scrap废钢scrap steel废料scrap废品率arate of rejects废品率，退件率，不良率reject ratio废品率，退件率，不良率rejection rate，reject atio 废气exhaust gas废气waste gas废热waste heat废铁iron scrap废铁scrap iron废铸料cast scrap分布distribution分部模型section pattern分部心型sectional core分层浇口side step gating分层进模口side step gate分层精炼法zone refining分次式混合机batch mixer分次式火炉batch type annealing furnace分次式磨粉机batch mill分次式配砂场batch sand plant分次式熔炉batch furnace，batch-type furnace)分次退火炉periodic annealing furnace分道砖runner core分度盘dividing plate分度圈limb分段淬火interrupted quenching分段淬火stage hardening分段淬火step quenching分段时效interrupted aging分段退火stepped annealing分级，刻度graduation铸造学专业英语词汇(7)分级节(模砂) classifying screen分级进模口steeped sprue分级进模口step gate分级进模口stepped side gate分级进模口铸造step gate casting分级筛grading screen分级筛size screen分级摇动筛size jigging screen分级硬度gradient hardness分件图parts drawing分解resolution分离器separator分离筛sepaating screen分离型波来铁(球状云明碳机) divorced pearlite 分模粉parting powder分模剂parting agent分模剂parting compound分模面mold joint分模面parting surface分模面进模口parting gate分模砂parting sand分模线parting line分模纸parting paper分配流槽distributing launder分配销(压铸) sprue pin分支砂心，分支心模branch core分铸试验separately cast test bar分子molecule酚phenol酚<<an017>>喃树脂phenolic furan resin酚甲醛树脂phenol-formaldehyde resin酚树脂phenolic resin酚塑，黏结剂phenol plast binder粉煤powdered coal粉煤pulverized coal粉煤装置powdeed coal equipment粉末金属powdered metal粉末金属机件powdered metal parts粉末冶金，粉末冶金术powder metallurgy粉状石墨plumbago封闭sealing封闭剂sealing compound封闭砂条sealing ring封罐退火pot annealing封合模型，分割模型parted pattern封盒退火box annealing封漏，浸入impregnation风锤air hammer风管输送机pneumatic tube conveyer风管输送系统penumatic tube dispatch system 风化石锥辗硅砂conical sand from stone风口，风嘴tuyere风口棒tuyere bar风口比tuyere ratio风口带tuyere zone风口面buyere line风力分级air classification风力净化法air cleaning process风量，体积air volume风量计air volume meter风量计blast volume meter风量控制仪air weight controller风干air drying风干法air seasoning风干强度air strength风干强度air-dried strength风扇fan风速计anemometer风箱air belt风箱air box风箱air tank风箱wind belt风箱wind box风硬air hardening风硬钢air-hardening steel枫木maple蜂巢炉beehive oven蜂巢炉焦炭beehive coke蜂蜡bees wax伏利安[气体]搅拌法voianik method氟(F) fluorine浮渣dross浮渣incrustation浮渣，夹渣scum浮渣，撇渣skim幅射高温计radiation pyrometer幅射管炉radiant tube furnace复合辊composite roll复合接种剂complex inoculant复合涂膜complex coating复合形砂compound sand复合铸造composite casting复磷repetition castings复热器recuperator复热系统recuperative system复置模型试模replacing pattern in the mold 复制品replica腐蚀corrosion腐蚀脆化corrosion embrittlement附件accessories附浇口系模型gated pattern附设铸工场capitive foundry附设铸工场tied foundry附体试杆cast-on bar附体试杆cast-on test bar附体试片test coupon附体试片test lug附体试验attached test coupon负偏析negative segregation负载load副产焦炭by-product coke副电流sedondary current副料indirect materials副线圈secondary coil腹板web覆盖热cover heating折心展性铸铁iron oxide covering覆盖层[熔剂], 涂层covering flux钆(Cd)(烯土金属) gadolinium改良合金modified alloy钙(Ca) calcium钙系膨土calcium bentonite灰汁，碱水lye盖M法，疏塞气体搅拌法Gazal process 甘油glycerine坩埚crucible坩埚底座，垫砖stool坩埚式感应电炉coreless induction furance 坩蜗吊钳crucible lifter坩蜗法crucible process坩蜗钢crucible steel坩蜗浇铸装置crucible pouring device坩蜗炉crucible furnace坩蜗钳crucible tongs坩蜗涂浆crucible wash杆，棒，条bar杆盘松砂机spike disintegrator杆条矫直机rod straightener感应淬火induction quenching感应电炉electric induction furnace 感应电炉induction furnace感应加热induction heating感应器inductor感应线圈induction coil感应硬化induction hardening橄榄石砂oliving sand刚铝，杜拉铝duralumin刚铝石alundum刚模半边(压铸) die half，die cast刚模钢die steel刚模试验(压铸) die try-out，die cast 刚模穴(压铸模) die cavity刚砂emery刚性rigidity刚玉corundum纲丝netting wire纲状组织(金相) net-work structure 钢steel钢厂steel works钢锭steel ingot钢坩埚steel crucible钢皮镁砖metal-case magnesite brick 钢输送带steel conveyor belt钢水瓢，抹砂匙spoon钢水瓢测温法spoon test钢丝钳pliers钢丝刷wire brush钢丝索wire rope钢丝位wire cut钢条bar steel钢条steel bar钢线粒cut wire shot钢屑，废钢料steel scrap钢性铸铁semi-steel钢铸件steel castings高傲砂blended sand高级钢high-grade steel高级铸铁high class cast iron高级铸铁high grade cast iron高加波感应电炉，高频率感应电炉high frequency induction furnace 铸造学专业英语词汇(8)高架磁选机overhead magnetic seperator高架单轨overhead monorail高架起重机gantry crane高拉力黄铜high tensile brast高拉力铸铁，高强度铸铁high tension cast iron高磷生铁high phosphorus pig iron高磷生铁phosphoric pig iron高岭石kaolinite高岭土kaolin高硫钢(易切钢之一种) sulphur steel高炉shaft furnace高炉，鼓风炉blast furnace高炉焦furnace coke高炉煤焦，鼓风煤焦blast furnace coke高铝红柱石mullite高锰钢Hadfield's manganese steel高锰钢铸件high manganese steel castings高黏土砂fat sand高黏土铸砂loamy sand高强度钢，高拉力钢high tension steel高强度黄铜high strength brass高强度铸铁high strength cast iron高碳钢high carbon steel高温淬火hot quenching高温计pyrometer高温耐火砖highly refractory brick高温强度(铸砂用) hot strength高温烧结high sintering高温试验hot test高温冶金学pyrometallurgy高硅生铁silvery iron高硅砖high siliceous brick高压罐bomb高压水清砂机hydro-blast高压造模法high pressure molding高氧化铝砖high-alumina brick高氧砖alumina brick高硬度钢glass hard steel高周波干燥，高频率干燥dielectric dry高周波干燥机，高频率干燥机dielectric dryer高周波砂心干燥炉hign-frequency core drying stove 搞压试验compression test锆(Zr) zirconium锆砂zircon sand锆石粉zircon flour锆英石zircon格子(结晶) lattice格子结构lattice structure格子筛分输送机grid type screening conveyor格子形耐火砖checker brick隔条砂箱barred box镉(Cd) cadmium铬(Cr) chromium铬钢chrome steel铬基耐火材料chrome base refractories铬克合金nichrome铬镁砂chrome-magnesite铬砂chromite sand铬砂hevi sand铬酸处理chrome pickle treatment铬酸处理(镁锌铸件镀铬) dichromate treatment铬铁ferro-chromium铬铁矿chromite铬铸铁chrome cast iron铬砖chromite brick给砂机sand expansion工地熔接site weld工具tool工具钢tool steel工具台tool table工模jig工资labor cost工作场所working aea工作大纲图表outline process chart工作路线排定rounding工作台working table工作图，制造图working drawing弓锯hack saw弓锯机hack-sawing machine公差tolerance。
铸造专业英语词汇
铸造专业英语词汇Abating退火Batch mill / batch sand mixer 混砂机Beader pearlite 珠光体Abrasion磨损Bed charge/coke 底焦Abrasive paper 砂纸Belt grinder Abrasive wheel 砂轮带式磨光机Bending strength 附件，活块Accessory 抗弯强度Bentonite 膨润土Acicular ferrite 针状铁素体Binder 粘结剂Acid refractory 酸性耐火材料Bituminous coal dust/black dust 煤粉Acid-proof cast iron / acid-resistance casting/Black short 冷脆acid resisting cast iron 耐酸铸件Black skin 黑皮，铸皮Acid slay 酸性渣Blank 毛胚，下料Active clay 有效粘土Blast AFS fineness 美国铸造学会型砂粒度鼓风，送风Blast capacity 风量Agitator 搅拌机（型砂试验）Blast fan 离心式鼓风机Agitation 搅拌Blast hole 风口Air blower 鼓风机Blast intensity 鼓风强度出气口（浇注系统）Air drainBlast pressure gage 风压表Air pollution control 大气污染控制Blast regulator 风量调节器Air tightness 气密性Blast volume 风量Air vent 出气孔Bleed 缺肉，台箱跑火余量，津贴，补助，宽容AllowanceBlender 混砂机，搅拌机Alloying agent 合金元素Blind feeder/head 暗冒口Alloying component 合金成分Blind roaster 马弗炉Anti-rust 防锈Blind scab 起痂氩气ArgonBlister 雾化，喷雾皮下气泡AtomizationBlow down Atomizer test 雾化试验（检验金属表面油脂）停炉Boiling point 沸点Attack 侵蚀Bond 侵蚀抛光法粘结剂，合同Attack polishing methodBond clay Automatic charging 造型粘土自动加料Bond strength 粘结强度自动切除冒口Automatic de-sprueing Bottom door 炉底们自动造型Automatic moldingBottom drop Automatic pouring device 自动浇注装置打炉Breaking-in 自动化砂处理装置Automatic sand plant 带肉Brinell hardness 布氏硬度Brittleness 脆性干砂芯Baked coreBrittle fracture 脆性断口，脆性断裂余额天平Balance /B type graphite B 球状冒口型石墨Ball feederBuffing 抛光布氏硬度Ball hardnessBuffing machine 布氏硬度机抛光机Ball hardness testing machineBunker Ball mill 球磨机料斗CE carbon equivalent 碳当量Band/belt conveyer 皮带输送机Carbide Band/belt elevator 碳化物皮带斗式提升机carbon dioxideBar bend test 试棒抗弯试验二氧化碳carbon monoxide Base 一氧化碳底，基础carbon pick-up 增碳基线Base linecarburetter 底板Base plate 增碳剂，汽化器case hardening 原砂Base sand 表面硬化内浇口case gate 碱性的，基本的Basiccasting alloy 铸造合金Coremaking 制芯Coresetter 下芯机casting defect/ casting flaw 铸造缺陷Cover 覆盖剂casting design 铸造设计Cross gate 横浇道casting equipmentCrush casting ladle 浇包掉砂Cupola 冲天炉casting lap 铸造冷隔Cupola drop 打炉casting leakage 铸造渗漏Cupola lining 铸造方案炉衬casting planCupola spout 出铁槽casting property 铸造性能Cut-off machine 切割机casting rate 浇注速度casting skin 铸皮，黑皮casting strain 铸造（内应力）变形Damper casting stress 铸造应力减震器Damping capacity / effect 减震能力/效果casting surface表皮Datum face / line casting technique 基准面/线铸造工艺/技术Deadhead 冒口废料cast integral test bar 单铸试棒Deburring 打毛刺腻缝，抿灰caulkDefect index 废品率Celsius thermometer 摄氏温度计Deformation 渗碳体，碳化铁变形CementiteDensity Center gate 中心浇口密度Degreaser 脱脂剂Center line 中心线Degree of graphitization 石墨化程度Chain hoist 手动葫芦Dimensional stability 尺寸稳定性加料Charging Descale Charger 加料机除锈，除氧化皮Decaling除锈，除氧化皮批料炉料Charging material /Design drawing 设计图冷铁Chilled cast ironDeslag Chill element 促白口元素扒渣Destructive testing/inspection 破坏性试验/Chilling action 激冷作用检验Chilling tendency 白口倾向Desulfuration / desulphurization 脱硫菊花状石墨Chrysanthemum graphite Desulfurizer 夹渣脱硫剂Cinder inclusionDetection Cinder notch 检查，摊伤出渣口Die cavity Clay washer 洗砂机型腔，模腔Clockwise rotation 顺时针方向Differential hardening / heating / quenching局部硬化Clowhole / contraction cavity 锁孔/加热/淬火Diffuse Cold box process 冷芯盒制芯法扩散Dilatant Cold lap / cold shut 膨胀冷隔Dilute Collapsibility / lubricate 溃散性稀释，冲淡Dimensional error / tolerance 稠度，浓度，一致性Consistency 尺寸误差/公差Direction l solidification Continuous desulfurization 顺序凝固，定向凝固连续脱硫Contamination Dirt / dirt inclusion 污染夹渣Conveyor belt 溃散，崩解，分解输送带，传送带Disintegration冷却剂Cooling agent 圆盘给料机Disk feederCooling curve 冷却曲线位错Dislocation冷却作用Cooling effect 置换/Displacement 位移散热冷却速度Cooling rate Dissipation heat砂芯Core 模变形Distorted patter变形，扭曲Distortion Core boxDivorced pearlite 粒状珠光体Flaw detection 探伤Floatation 漂浮Down runner / gate / downright 直浇口Flowability/fluidity 流动性Ductile iron 球墨铸铁Flow-chart Duff 煤粉流程图Fluid contraction 液态收缩Durability 耐用性，耐久性Flushing 流渣Dust catcher 集尘器Fold 冷隔Foreign substance elastic deformation 弹性变形杂质Forging 锻造Elementary analysis 元素分析Forklift 叉车Elevator 提升机Free carbide 游离碳化物Elongation 延伸率，延长Free cementite Endurance 耐用性，持久度游离渗碳体Free ferrite 疲劳极限游离铁素体Endurance limitFreeting/fritting 烧结Energy loss 能量损失Frictional coefficient 摩擦系数环境污染Environment contaminationFront slagging 炉前出渣Environmental control 污染控制平衡EquilibriumGalvanizing 电镀Eutectic 共晶体，恭晶的Gas blow/hole 气孔考试成绩Examination performance / resultGas blowhole 气孔Fading 衰退Gaseous diffusion 气体扩散Failure stress 破坏应力Gassy melt 毛刺，羽毛含气金属液FeatherGas tightness Feeding effect 补缩效果气密性Gate area 浇口面积Feeding gate 内浇口Gating = gating systemFeed/feeder head(=riser)/feeding head 浇口，浇口系统冒口浇口设计Ferric 铁Gating design渗碳体，碳化铁浇口比Gating proportion/ratio Ferric carbide 铁素体Ferrite 表，计，规Gauge=gage珠粒状渗碳体/锰铁Ferromanganese pearlite Globular cementite / Ferromolybdenum 钼铁光体Grain-boundary segregation 晶界偏析Ferrosilicon 硅铁Fettle 铲除炉壁渣子Grain fineness distribution 粒度分布锉刀File 石墨漂浮Graphite floatation/Filter paper/screen 滤纸网石墨化GraphitizationFin 毛刺Green compression strength 湿压强度精加工Final machining 灰铁Gray/grey cast iron打磨，磨制Fine silt 粉尘Grinding砂轮Grinding wheel 加工余量Finished allowanceHeat loss 热损失加工面Finished surface耐火砖Fire brick Heat stress 热应力Heat-treating / heat treatment Fire cracking 热裂热处理Fire resistance 热效应耐火性Heating effect厚壁铸件大型铸件/ 烧损Fire waste Heavy castingHeavy-walled 夹具Fixture 厚壁的片状Flake form 保温炉Holding furnaceFlake graphite 片状石墨热裂Hot tear/pool剥落Flaking off (=spalling) 液压千斤顶Hydraulic jack氢Hydrogen 闪点Flash pointHyxagonal screen 六角筛Machine allowance 加工余量Machining 机械加工Macrograph 宏观Impact hardness/toughness 冲击硬度/韧性Magnetic flaw detection Impermeability 气密性，不渗透性磁力探伤Magnetic field 压痕，型腔，凹腔磁场ImpressionMagnetic-particle inspection 磁粉探伤Impurity 杂质Magnetic powder inspection Included slag 夹渣磁粉探伤Magnification 放大倍数，放大倍率Indigeous graphite 析出石墨Manganese 锰Induction 感应Margin tolerance 极限公差孕育剂InoculantMass production 大量生产Inoculation fade 孕育衰退Matrix hardness 机体硬度Inside diameter 内经Mean diameter / stress 平均直径/应力stream inoculation / Instantaneous ladleMean value 中间值inoculation 瞬时浇包孕育Mechanical allowance 加工余量绝缘，隔离InsulationMechanical property 机械性能Internal porosity 内缩松Meltableness 可溶性Internal shrinkage 内部缩孔Melting 溶解Internal stress 内应力Melting capacity/ condition / efficiency 熔化率Inverse chill 反白口/状况/反白口Inverted chill 效率Melting point 渗碳体，碳化铁熔点Iron carbideMetal graphic microscope 铁焦比Iron-coke ratio 金相显微镜Metallic charge to coke ratio 铁焦比Metallic pattern 金属模千斤顶JackMetallograph 金相图片Jet test 喷射试验（侧电镀层厚度）Metallographic examination 生产定额Job rate 金相检验Metallographic laboratory Knock-off head 易割冒口金相试验室Metallographic microscope 金相显微镜落砂，出芯Knockout Metallographic specimen 金相磨片Knop 钮，电钮Metallurgy 冶金学Metal material 金属材料Microanalysis 不稳定的Labile 微量分析，显微分析Microlug 球化率怀素测定试帮强劳动（力）区Labor-intensive areaMicron Ladle 浇包微米Mismatch Lamellar pearlite/laminate pearlite 错模片状珠光Misrun 缺肉，浇不到体Modulus of elongation 延伸率Late inoculation/post inoculation 二次孕育Molding line 造型线设计Laying out Natural gas 天然气浇漏，漏铁水LeakerNodularization lift truck 叉车球化Nodularizer Light casting 球化剂小铸件，薄壁铸件Notch brittleness Liquidus 液相线缺口脆性Locating point/surface 面/ 基准点Off-dimension 烧损Loss on ignition 尺寸不合格（常指铸件）Off-gage 下限Lower limit 尺寸不合格（常指型芯）Offset 光泽Luster 错位，偏置Operation life 使用期限，寿命外观检验Outer inspection / visual inspection 切削性能Machinability Outlet 出口，排出口Refractoriness 耐火性Refractory property 耐久性能Oxidation 氧化Regulator 调节器Oxide ferric 氧化铁，三氧化二铁Reinforcement 加固Rejected casting 不合格铸件Resin 树脂Partial hardening / local hardening 局部淬火Returns 回炉料Parting face 分型面，分模面Reverse chill 反白口Pattern plate 模板Revolving table feeder Patter spray 脱模液圆盘给料机Rimhole 拔模斜度皮下气泡Pattern taper / patter draftRiser 冒口Pearlite 珠光体Rockwell hardness Permeability test 透气性试验洛氏硬度Rosette graphite 菊花状石墨Phosphide 磷共晶，磷化物Roughing 粗加工'Physical property 物理性能Roughness 粗糙度生铁Pig ironRounding Pin hole 针孔倒角Roust inhibitor 防锈剂Pitted skin 麻面（铸造缺陷）Runner gate 横浇道Plastic binder 树脂粘结剂Runner system 浇注系统塑性变形Plastic deformationRunning and feeding system Plate feeder 圆盘给料机浇冒口系统Rust prevention Plating 电镀防锈抛光Polishing Rustless steelPorous casting 不致密铸件，多孔铸件Safety and industrial gloves 劳动保护手套二次孕育Post inoculationSafety factor 未浇满Poured short 安全系数（铸造缺陷）Safety goggle 护目镜Preheat/preheating 预热Safety precaution 安全措施过早凝固Premature freezingPremium casting 保质量逐件，优质逐件Sample inspectionSampling 取样Preset program 预定计划，预定程序表Sand blister 砂眼Pressure atmosphere 大气压Sand blow 加压冒口Pressure feeder 气孔Sand buckle 起皮、夹砂Production capacity 生产能力Sand burning 粘砂劳保手套Protective glovesSand-conditioning system 试生产铸件砂处理系统Prototype castingSand control Push-off 推出，顶出型砂控制Sand core 砂芯Sand cut 冲砂淬火时效Quench agingSand defects 型砂造成的（铸造）缺陷Sand drop 掉砂散热器，散热片，暖气片RadiatorSand explosion 砂眼Radioactive element 放射性元素Sand fineness 砂子平均粒度稀土Rare earthSand flowability 型砂流动性惰性气体Rare gasRat 多肉Sand mill / sand mixer / sand mixing machine/ sand muller 铰刀混砂机ReamerSand mold 砂型再生，回用ReclamationSand shakeout 热脆性Red brittleness=hot brittleness 落砂Sand wash 还原能力Reducibility 冲砂铸痂Scab 断面收缩Reduction in areaScar 凹痕Surface roughness 表面粗糙度Swell 胀砂Semi-finished product 半成品Sensitivity 敏感性test Separate cast test bar = cast integrateTap hole bar 单铸试棒出渣口Telltale 落砂机定位标记Shakeout 落砂/Tenacity / tensile strength Shaking conveyer 震动输送机抗拉强度/韧性班次Shift Tensile testing machineTension-active 浇不满Short-run element 反球化元素、干扰元素Short run casting 浇不足铸件，缺肉铸件（未Test bar 试棒浇满）Test block Shrink hole 收缩、锁孔试块Test piece 试样Shrinkage porosity 缩松Test specimen 试样/试棒/试块Shrinkage strain 收缩变形Thermal balance 热平衡Shrinkhead 冒口Thermal conductivity 导热系数，导热性Sintering 烧结Size tolerance 尺寸公差Thermaldeformation/dilatometer/expansion/fatigue 扒渣除渣/ 热Slagging -off变形/ Solidification contraction/shrinkage 凝固收缩膨胀仪//膨胀/疲劳Tightness 紧密度，致密度Solid-liquid interface 固液相交界面Tolerance 公差Solidus/solidus curve/solidus line 固相线Tooling point 基准点溶液浓度Solution concentrationTuyere gate Sonic inspection 听声检验风眼比重Specific weight光谱分析SpectroanalysisUltimate 极限球状石墨Spherical graphiteUpper limit Spheroidal iron = ductile iron 球墨铸铁上限Vacuum treatment 真空处理球化SpheroidizationVentilating 主轴system/device/equipment 通风系Spindle统/装置/设备基准点Spotting pointVenting quality透气性Steam tight test / air tight test 气密性试验Vibratory feeder 震动给料机多肉Sticker / ratStraightening 校正Vibratory shakeout machine = vibratory shakeout 震动落砂机强度试验Strength testVisual examination/inspection 外观检验Stress 应力Wash 冲砂应力消除Stress reliefWasher 洗砂机/ subsurface blow hole / blowhole Subskin Wearability / wear resistance sub-surface blister 耐磨性皮下气孔Wrinkle 皱皮Superficial cementation 表面渗碳Super heating 过热Yield strength 屈服强度过饱和SupersaturationZero defect casting 表面光洁度Surface finish 无缺陷铸件冷隔Surface folding 锌Zinc最新铸造标准应用手册（机械工业出版社）。
铸造学专业英语词汇
铸造厂，铸造foundry铸造尺shrink rule铸造尺shrinkage rule铸造尺shrinkage scale铸造从业员foundry man铸造法casting process铸造方案founding method铸造方案plan of casting铸造废料foundry scrap铸造机casting machine铸造计划casting plan铸造设计，铸件设计casting design 铸造性试验castability test铸造应变casting strains铸造用钉foundry nails铸造用生铁foundry pig iron铸造状态as-cast condition，as-cast铸造组织cast structure铸造作业casting manipulations铸芝模ingot mold铸芝偏析ingotism抓斗绞车装置grabbing gear专业铸造工场production foundry砖brick转变用铁水(调配成分) transition iron 转动炉，转筒炉rotary furnace转换conversion转炉converter转炉钢converter steel转炉炉榇converter lining转盘混砂机rotating pan mill转速revolving speed转台，转盘rotary table转台喷粒机shot tablast转位半径transititon radius转运车transfer trolley转运翻箱装置transfer-turnover device 转运盖c装置transfer-closing device 转运装置transfer device装砂心coring up装载机bucket loader装载能量loading capacity追补焦split coke锥形炉腹bosh坠裂试验shatter test坠落试验drop test坠重试验drop-weight test自动电极控制automatic electrode control自动电流调整器automatic current regulator自动化automation自动化系统automatic system自动加料设备automatic charging equipment自动进给automatic feeding自动控制automatic control自动配料机automatic doser自动燃烧控制automatic combustion control自动送料(压铸) automatic ladling，die casting自动温度控制器automatic temperature controller自动造模工场automatic molding plant自动铸砂处理设备automatic sand plant自动转盘式造模机automatic turntable molding machine 自来水tap water自然腐蚀试验field test自然裂缝seasoning shake自然破裂season cracking自然干燥法(木材)，自然季化处理(铸件) natural seasoning 自然时效natural aging自然通风natural draft自行除渣self-skimming自行除渣风口self-slagging tuyere自行结晶idiomorphic crystal自行退火self-annealing自硬钢self-hardening steel自硬性self-hardening自硬性造模法no-bake process自硬性粘结剂self-curing binder自由度degree of freedom自由水free water纵向裂痕longitudinal crack足尺full size阻挠元素interfering element阻销stop pin组成图constitutional diagram组成物component组成楔值constitutional wedge value组合built up组合构造composite construction组合模板built-up plate组合模型built-up pattern组合模型composite pattern组合模型pattern assembly组合砂箱built-up molding box组合砂心盒multiple core box组织，级成constitution组织成分constituent组织瑕疵structure defects钻悄(试样用) drillings钻维硬度值(韦克氏硬度) diamond pyramid hardness number，Vickers hardness 最大负载maximum load最后加工finish最适水分(模砂) optimum temper moisture作业可靠性operational reliability作业砂(生产线) production sand作业准备日程operational scheduling直立浇铸vertical pouring直立心型端承，直立砂心头vertical coreprint直立旋板心轴upright spindle直立造模vertical molding直立造模法mold on end直立铸模vertical mold直立铸造vertical casting直落砂心drop core直木纹edge grain直提砂心头tail print直通干燥炉through feed drying furnace直显照片(金相) direct print直压式合机direct pressure closing植物油vegetable oil指形进模口finger gate酯系硬化法ester-process制震能damping capacity蛭石vermiculite置冲法pour-over method置冲法transfer method置模箱set-off box滞流(铸疵) mistrun制程退火process annealing制模型铣床pattern milling machine制图，起模drawing制造熔接production welding制造冶金学process metallurgy质量效应，厚薄效应mass effect致密度consistency中间处理intermediate treatment中间检查intermediate inspection中间金属intermediate metal中间砂箱，中间模箱cheek box ，cheek flask中间砂箱，中间模箱raising middle flask中磷生铁(P0.4-0.75%) medium phosphorus pig iron 中模，中间砂箱，中间模箱cheek中碳钢medium carbon steel中途添焦spreader charge of coke中线收缩centerline shrinkage中心板，旋刮板心轴承座center plate中心规centergage中性耐火材料neutral refractory materials中性熔渣neutral slag中性砖neutral brick中周波感应电炉intermediate frequency furnace 锺，锺形塞进器bell锺青铜bell bronze重搭overlap重捣砂hard ramming重金属铸件heavy-metal castings重晶石heavy spar重力分离器gravitational separator重力滚子输送机(倾斜式) gravity roller conveyor 重力偏析gravity segregation重力输送机gravity conveyor重力压铸法gravity die casting重力铸造法gravity casting重燃油heavy fuel oil重熔remelting重熔工场secondary smelter重印法(造模) print back重油heavy oil重整石英砂replenishment quartz sand重铸recasting轴shaft轴承合金bearing metal皱痕面(铸疵) creasy surface皱皮(铸疵) orange peel皱皮(铸疵) surface folding珠，粒，击，射注过程(压铸) shot珠击处理shot peening珠击机shot peening machine珠粒喷击清理shot blasting珠泡bead竹叶状液面花纹bamboo leaves pattern主成分，基本金属primary coil主模master mold主心型，主砂心body core煮材干燥法boiling seasoning助流剂fluidizer助黏剂，膨胀性粘结剂swelling binder注入槽(压铸) pouring shot注射器injector柱column柱pillar柱塞，塞罩plunger柱塞，塞罩post柱状结晶columnar crystal柱状组织columnar structurew 仓壁冲击振动器impact vibration on bin wall 贮砂桶匣(砂心机用) magazine铸包camlachie cramp铸壁wall铸壁鹌鹑wall thickness铸补burning on铸补tinkering铸成率casting yield铸成试片cast-to-shape specimen铸尺contraction rule<BR>铸疵casting defect铸疵defect test铸疵，铸造缺陷foundry defects铸疵试验defect test铸锭ingot铸锭底砖spider铸锭浇口砖king brick铸锭模ingot case铸锭状态as-ingot铸钢cast steel铸钢造模料steel foundry molding compound铸工caster铸工founder铸合金ferro-alloy铸弧pouring arc铸件castings铸件表面casting surface铸件表皮casting skin铸件飞边，铸件毛边casting fin铸件内包物cast-in insert铸件清理，最后加工finishing铸件清理图dressing shop铸件修整finishing of castings铸件应力casting stress铸焦foundry coke铸坑casting pit铸坑foundry pit铸裂(铸疵) casting crack铸瘤rising铸漏bleed铸漏break out铸漏run-out铸漏件bleeder铸模mold，mould铸模布置mold layout铸模除除掉(压铸) impression block铸模龟裂，脉状痕(铸疵) veining铸模夹具mold clamp铸模输送机mold conveyer铸模块合mold assembly铸耙rake铸皮skin铸皮孔skin holes铸砂casting sand铸砂处理foundry sand preparation铸砂处理preparation of sand铸砂处理工场foundry sand preparation plant 铸砂控制sand control铸砂控制设备sand control equipment铸砂流动性flowability of sand铸砂流动性foundry sand铸砂膨(铸疵) sand drier铸砂强度试验strength test of sand铸砂强化strengthen the sand铸砂烧结(铸疵) sand burning铸砂烧贴(铸疵) sintering point铸砂油casting iol铸生铁机pig machine铸损foundry losses铸损，不良铸件waster，foundry losses铸铁cast iron铸铁工场iron foundry铸铁管cast iron pipe铸铁组织图cast iron diagram铸铁组织图structural diagram of cast iron 铸造founding铸造，铸件casting铸造场smith shop圆盘砂轮机disc grinder圆套筒round bush圆条测温法bar test圆筒式炉(回转炉) drum type furance圆筒形浇桶drum ladle圆头镘刀roound nose圆形砂rounded grain圆形砂粒rounded sand云母粉mica flour云母粉mica powder运轮，台车carriage运送箱tote box运原性蒙气reducing atmosphere运原状态reducing condition杂质impurities再炽，再辉recalescence再炽点，再辉点recalescent point再处理erpreparation再处理砂reconditioned sand再负载reloading再结晶recrystallization再结晶温度recrystallization temperature 再冷却系统recooling system再黏接砂rebonded sand再热炉reheating furnace再生砂reclamation sand再生铁remelted pig iron再生铁synthetic pig iron暂垫造模法mold on an oddside凿锤chipping hammer凿刀chipping chisel凿磨浇口shagging凿平chipping凿平问chipping room凿子，凿机chipper凿子，凿机chisel造模molding造模板mold board造模板molding board造模板molding plate造模板ramming plate造模材料molding materials造模材料添加剂molding material additive造模粗砂molding gravel造模地坑molding pit造模钉molding brad(pin)造模法molding method造模工具molder's tools模工作台molder's bench造模工作台molding bench造模机molding machine造模袷度molding allowance造模区molding bay造模设备molding apparatus造模性moldability造渣剂slag forming constituent造渣期slag forming period造渣石灰slag lime造渣作业slag practice增碳carbon pick-up增碳recarburization增碳剂recarburizer增碳剂recarburizing agent增碳焦recarburization coke增压冒口，威廉氏冒口atmospheric feeder(atmsopheric riser，William's riser) 增压冒口，威廉氏冒口William's riser，atmospheric riser增压砂心cracker core增压砂心pencil core增压砂心penetration core增压砂心，嵌入砂心insert core增压砂心，威廉氏砂心atmospheric core，William's core渣dirt渣比，碱度slag ratio渣阱dirt trap渣孔(铸疵) slag blowhole渣棉slag wool渣壳slag crust渣桶slag ladle渣位高slag level渣窝slag pocket轧辊，辊子roll轧屑roll[ing] scale闸喉，闸口choke闸喉式流道choked runner system闸喉作用choking粘土质耐火砖fire clay brick展性，可锻性malleability展性处理malleablising展性热处理铁矿malleable ore展性退火malleablising annealing展性铸铁(可锻铸铁) malleable cast iron展性铸铁(可锻铸铁) malleable iron展性铸铁用生铁malleable pig iron辗制硅砂artifical silica sand章鱼状石墨octopus graphite胀疤expansion scab胀模(铸疵) swell胀陷，上模剥砂(铸疵) pull down罩式炉lifting furnace遮蔽电弧熔接shielded-arc welding遮热板heat shield折旧amortization折旧depreciation折缘(黑心展性铸铁) picture frame锗(Ge) germanium真空除氧法vacuum degassing process真空精炼vacuum refining真空熔解vacuum melting真空造模法，V造模法V-process，vacuum-secaled process 真空铸造vacuum casting真离心铸造法true centrifugal casting砧anvil砧台式震实造模机anvil-jolter针对铸铁acicular cast iron针孔(铸疵)，销孔pin-hole针状组织acicular structure针状组织铸铁bainite cast iron振动vibration振动捣砂vibration ramming振动分配器vibrating distributor振动器vibrator振动清箱mechanical knockout by vibration振动清箱，振动清砂处shake-out振动清箱机molding box shake-out device振动清箱机，振动清砂机shake-out machine振动清箱性能shake-out property振动清箱栅shake-out grid振动清箱栅shake-out screen振动筛jigging screen振动筛shaking screen振动筛vibrating sieve震捣jolt ramming震动jolt震动板jolting plate震动废黜模板造模机jolt molding machine with turnover plate震动机jarring machine震动清箱吊架jointing hanger震动压挤拔模造模机jolt squeeze stripper molding machine震动压挤造模机jolt squeeze molding machine震动造模机jolt molding machine震动造模机jolter震箱清砂机flask shanker蒸馏器retort蒸馏碳retort carbon蒸气脱蜡autoclave dewaxing整流器rectifier整体模型solid pattern整体模型铸模solid pattern mold整温控制thermostattic control整缘trimming整缘模具trimming dies整缘压机trimming press正常化normalizing正常偏析normal segregation正常温度normal temperature正常折曲试验normal bend test支架(压铸)，垫块packing block支台，置模台set-off bench支柱(熔铸炉) prop枝形进模口bracnch gate直尺staight edge直接电弧炉direct arc furnace直接浇口drop gate直接浇铸direct pouring直接浇铸法direct casting直接进模口direct gate直接进模口slot gate直接气压式热室压铸机(压缩空气直接压于熔液) direct pressure hot chamber machine氧化硅基砂silica base sand氧化性蒙气oxidizing atomosphere氧化性溶解oxidizing melting氧皮铝alumite氧焰割oxycut氧乙炔熔接，气焊oxyacetylene welding样板，刮板，量具template，templet样规sizing peg摇动炉rocking furnace摇斗炉shaking lade摇台cradle窑炉kilnb趸?anti-oxidant冶金焦metallurgical coke冶金术metal technology冶金学metallurgy液化liquefaction液面花纹break surface pattern液面花纹figure液面花纹play figure液态收缩liquid contraction液态收缩liquid shrinkage液体压力计manometer液相曲线liquidus curve液相线liquidus [line]液相线liquidus line液压气动砂箱升提机构hydropneumatic flasklifting mechanism 液压千斤顶hydraulic jack液压清砂铸件设备hydraulic cleaning equipment液压试验hydraulic pressure test叶轮式喷砂机turbine sand blaster一氧化碳carbon monoxide一氧化铁(FeO) iron protoxide铱(Ir) iridium移动吊车mobile crane移动皮带升降机mobile belt elevator移动式烘炉portable drying oven移动式烘模机portable mold dryer移动式可倾前炉removable clay matter移动式摔砂造模机motive type sand slinger移入shunting-in移位装置shifting facilities移装(外砂心) draw back移装砂心inset core遗传性heredity乙二醇glycol乙炔acetylene乙炔发生器acetylene generator乙炔墨acetylene black(acetylene smoke)乙炔墨acetylene smoke，acetylene black乙炔熔接acetylene welding抑制剂inhibitor易开砂箱easy off slip flask易燃物inflammable易熔合金fusible alloy异形管件specials意外防止条例accident prevention regulations溢放口flow off溢放口pop off溢放口run-off溢放口strain relief溢放冒口run-off riser溢流over flow溢流道flow through溢流口hot spruing溢流口(压铸) over flow well音波试验sonic testing阴极锈法cathodic protection阴极氧化anodic oxidation铟(In)(稀金属元素) Indium银(Ag) silver银砂(无铁质硅砂) silver sand引导顶出(压铸) guided ejection英高镍(镍铬合金) Inconel英国国家标准B.S.(British Standard)英国铸铁研究协会BCIRA(British Cast Iron Research Associatin)英国铸造工程师学会IBF(Institute of British Foundrymen，London) 英制热单位(B.T.U.) British Thermal Unit应变，变形(铸疵) strain应变计strain gage应力stress应力腐蚀裂痕stress corrosion cracking应力集中stress concentration应力破坏强度stress upture strength应力消除stress relief应力应变特性stress-strain characteristics应力应变图stresss-strain diagram樱木cherry tree荧光采伤法zyglo荧光渗透剂zyglo penetrant荧光fluorescence荧光镜fluoroscope荧光探伤法fluorescent crack detection荧光透视法(检查)，荧光镜试验fluorspar 萤石(CaF2) fluorite萤石(CaF2) flushing硬点hard spot硬度hardness硬度计hardness tester硬焊brazing硬化(壳模) curing硬化，淬火hardening硬化合金hardening alloy硬化剂hardening agent硬化剂，硬化合金hardener硬化加速剂hardening accelerator硬化能，淬火性hardenability硬化深度hardness penetration硬化时间curing time硬结setting硬结砂用油setting oil硬木hardwood硬砂模型板hard sand match硬质焦炭，煤焦hard coke永久模，金属(铸)模permanent mold用瓢装液(压铸) ladling用销抬起pin lift优尼造模法Unicast process优先方位(结晶) preferred orientation油淬火oil quenching油粉浸渗试验(裂痕检出试验) oil-chalk test 油炉oil furnace油泥砂浆oil loam油漆，涂料paint油砂oil sand油砂模oil sand mold油砂心oil bounded core油砂心oil core油砂心oil sand core油污金属切屑swarf油烟，烟灰soot油硬化oil hardening油质黏结剂oil biner柚木teak游标卡尺vernier calipers铀U) uranium有机粘结剂organic binder有孔砂心撑perforated chaplet有麻口冷硬层chill zone with mottle有箱造模法flask molding有效高度burden height有效高度effective height有效黏土含量effective clay content 釉，光滑glaze鱼油fish oil鱼嘴栅fishmouth gate榆木elm余留铁水heel余铁深度(炉) pool depth余隙，间隙clearance余液(低周波炉) liquid core雨段退火two-stage annealing雨淋式环浇口pencil ring gate雨淋式进模口pencil gate雨淋式进模口pop gate雨淋式进模口shower gate浴池式氮化法bath nitriding预热preheating预热带preheating zone预热空气preheated air预热器preheater预熔金属pre-melt原料raw materials原料工业primary graphite，G-graphite 原料金属primary industy原料生铁base iron原模型granular pearlite原砂，原产硅砂crude sand原砂透气度base permeability原生组织primary structure原油crude oil圆板塞(浇池) disc plug圆底提砂钩Yankee's lifter圆规compasses圆粒round sleeker圆抹镘trowel星形裂缝star shake星形铁(滚光用) jackstar，mill star，star星形铁(滚光用) mill star，jack star，star 星形铁(滚光用) star，jackstar，mill star星形铁(滚光用) tumbling stars形象因子shape factor型砖shaped brick修补removable tilting forehearth修毂抹刀boss spatula修角刀corner tool修角抹刀angle spatula锈rust锈皮，比例尺，秤scale锈皮，轧钢鳞片mill scale锈蚀度degree of rustin虚表比重apparent specific gravity虚表孔率apparent porosity虚表密度apparent density虚表容积apparent volume表温度apparent temperature虚筋，挡块(砂模) stop off蓄热炉regenerating furnace蓄热能量heat-retaining capacity蓄热器，再生器regenerator蓄热系统regenerative system续制铸件repeated use of sand旋臂吊车jib crane旋风集尘器cyclone dust collector(cyclon) 旋风净尘器cyclone scrubber dust collector 旋刮[砂] sweeping旋刮板sweep旋刮板sweeping board旋刮板臂sweep arm旋刮板马架sweeping molder's horse旋刮板模型sweeping pattern旋刮板模型sweeping template pattern旋刮板砂心swept core旋刮板心砂心spindle core旋刮板心轴，心轴spindle旋刮板轴心承座sweeping plate旋刮砂模sweeping mold旋刮砂心sweeping core旋涡补给口whirl-gate feeder旋涡混合机whirl mixer旋涡集渣包whirl-gate dirt trap旋沿试验法(流动性) spiral test旋转给料盘rotary feeding plate旋转刮板turning strickle旋转模板造模机truning plate molding machine旋转器swirl旋转干燥器rotary drier旋转砂心线setting line，core setting line旋转筛rotary screen旋转筛砂机rotary sand screen旋转式集尘器spin dust collection旋转台，转盘turn table旋转喂槽swivelling tundish旋转轧碎机rotary crusher悬吊砂suspended core悬吊砂轮机suspended grinder悬吊输送机trolley conveyor悬浮物suspended matter悬拱suspended arch悬挂式清箱装置pendant shaking equipment选别废料selected scrap雪明碳铁，雪明碳体cementite循环处理砂system sand循环砂recirculation system sand循环砂return sand压边整缘press trimming压痕试验indentation test压痕嚣，压痕物indentor压痕硬度试验机indentation hardness tester压坏(砂模)，粉碎crush压挤板squeeze plate压挤板squezze boad压挤捣砂squeeze ramming压挤机squeeze machine压挤式顶杆造模机squeeze pinlift molding maching 压挤头(造模机) squeeze head压挤造模机squeeze molding machine压挤铸造squeeze casting压紧废料packeted scrap压块briquet，briquette压块bundle压块废料baled scrap压块机briquetting machine压力pressure压力计pressure gage压力室添加法pressure chamber method压力通风follow board压力铸造pressure casting压漏(铸疵) leakers压漏试验leakage test压模印coining压膜式壳模机diaphragm shell molding machine 压膜式造模机diaphragm molding machine压实性compactability压实指数compactability index压碎机crusher压缩机compressor压缩机die casting machine压缩空气compressed air压缩空气缸compressed air cylinder压缩空气喷吵机compressed air sand blaster压缩空气软管compressed air hose压缩性compressibility压重，砝码weights压重板(震动压面) jointing plate压铸，刚模铸造de cast压铸储井shot well压铸储筒shot sleeve压铸法，刚模铸造法die casting压铸件die castings压铸模dies压铸模涂料，刚模涂料die coating压铸模块die cast assembly亚共晶合金hypoeutectic alloy亚共析合金hypoeutectoid alloy亚甲蓝试验methylenne blue test亚硫酸监稠浆(黏结剂) sulphur，sulfur亚铝美尔Alumel氩(Ar) argon氩净化器argon purifier烟囱chimney烟囱chimney stack烟囱，炉胴(熔铁炉) stable-equilibrium diagram 烟囱罩hood烟道chimney flue烟道气flue gas烟火bank，the cupola烟煤bituminous coal烟煤soft coal烟气(有害的) fume烟雾smog延性ductility延性材料断口ductile fracture延性铸铁(球状石墨铸铁) ductile cast iron，nodular cast iron 研究工程师research engineer研磨纸emery paper焰割gas cutting洋铜nickel silver阳极处理anodizing阳极铜anode copper扬尘量dust emission杨氏模数，杨氏[纵弹性]系数Young's moldulus氧(O) oxygen氧丙烷焰割oxy-L.P.gas cutting氧化oxidation氧化oxidizing氧化表皮oxide skin氧化带zone of ozidation氧化精炼oxidizing refining氧化精炼refining by oxidation氧化期oxidizing period氧化气孔(铸疵) oxidized blowhole氧化损耗oxidation loss氧化铁iron oxide氧化物oxide氧化硅(SiO2) silica物理变化physical change物理试验physical test物理性质physical properties物理冶金physical metallurgy雾化atomization西拉高硅铸铁Silal吸热反应endothermic reaction吸入输送机suction conveyor吸湿性试验(高湿状态) high humidity storage test吸收absorption吸收剂absorbent吸收器absorber析出，沈淀precipitation析出热处理precipitation heat treatment析出退火precipitation annealing析出硬化precipitation hardening硅(Si) silicon硅肥粒铁silico ferrite硅肺病，石米沉着病silicosis硅分析仪，砂计silicon meter硅钢板silicon steel plate硅化钙calcium silicide硅化钙calcium silicon硅黄铜silicon brass硅块silicon briquets硅铝钙合金calicum-aluminium-silicon硅铝明(铝硅合金) silumin硅锰钙合金calcium-manganesesilicon硅凝胶，硅胶吸湿剂silica gel硅青铜silicon bronze硅青铜soilzin bronze硅砂silica sand硅砂捣料silica ramming compound硅砂粉silica flour硅砂浆涂料silica wash硅砂石砖ganister brick硅树脂，硅酮silicone硅树脂滑脂silicone grease硅酸silicic acid硅酸监silicate硅酸钠，水玻璃sodium silicate硅酸四乙酯tetraethl silicate硅酸乙脂ethyl silicate硅铁ferro-silicon硅铜silicon copper硅线石砖(高铝氧(70Al2O5)硅质耐火砖) silimanite brick 硅岩轮辗硅砂impeller-breaker sand硅藻土diatomaceous earth硅藻土infusorial earth硅藻土kieselguhr硅质粘土silicious clay硅砖silica brick硒(Se)(化学元素) selinium稀土金属rare earth metal锡(Sn) tin锡汗珠(铸疵) tin sweat锡青铜tin bronze习用潜变限度conventional creep limit洗尘器，涤气机scrubber洗净器scrubbing liquid细锉刀finishing file细孔组织cell structure细裂痕(铸疵) hair crack细裂纹(铸疵) caplillary crack细密波来铁fine pearlite细泥砂浆finishing loam细砂，河海丘砂bank sand细土粉，细泥fine silt煅烧calcine煅烧白云石calcined dolomite煅烧窑calcining kiln瑕疵flaw瑕疵大小flaw size瑕疵位置flaw location揬工场，揬造炉fore-hearth forge揬铁锈皮forge scale揬造，揬件forging下降速率lowering speed下浇道，坚浇道down gate下浇道，坚浇道down sprue下模bottom part下模nowel下模，下砂箱，下模箱drag下砂箱，下模箱drag box下砂箱，下模箱drag flask夏比冲击试验charpy impact test夏比冲击试验机Charpy impact test machine 夏比冲击值Charp impact value纤维状滑石fibrous talc显热sensible heat显微镜microscope显微镜试验microscopic inspection显微镜学microscopy显微镜照像photomicrograph显微偏析micro-segregation显微缩孔(铸疵) micro-shrinkage显微像micrograph显微组织micro-structure限缩变形hindered contraction限外显微镜ultramicroscope相phase相对频率relative frequency相对湿度relative humidity相对硬度relative hardness相律phase rule相平衡phase equillibrium相图phase diagram响铜bell metal象皮皱纹(铸疵) elephant skin橡胶浇道棒(造模) rubber down gate橡胶浇道棒(造模) rubber pouring funnel橡胶输送带rubber conveyer belt橡木oak消除冷硬退火chill removing annealing消除应力开沟，防裂槽stress relieving grooving 消泡剂antifoaming agent消石灰，熟石灰slake-lime消退fading消退时限fading time硝酸浸蚀液nital硝酸浸蚀液nitric acid销pin销合pin closure销紧力locking force销孔试验片keyhole specimen销抬造模机pin-lift molding machine萧氏精密造模法Shaw process萧氏硬度Shore hardness小块料cobbing小胚billet小铸件small castings校准calibration校准块calibration block校准钮calibrating knob楔wedge楔表进模口wedge gate楔塞作用wedge action楔形进模口wedge runner bar楔形试片wedge test piece楔形试验wedge test楔形销wedge pin楔形压力试验wedge penetration test楔形砖key brick楔形砖wedge brick楔值wedge value斜导杆(压铸) cam finger斜度砂箱，滑脱砂箱slip flask斜方晶系(结晶) rhombic system卸斗skip卸斗吊车skip hoist心，心型，砂心core心材heart wood心骨core bar心骨core grid心骨core iron心骨core rod心骨管core barrel心骨矫直器core rod straightner心骨模core grid mold心骨模型core iron printer心骨切断器core rod cutter心骨轴core spindle心裂(木材) heart shake心砂core sand心砂混合机core sand mixer心形镘刀large heart trowel心型拔出装置(压铸) core pull assembly心型撑，砂心撑chaplet心型固定门(压铸) heel block心型滑板(压铸) core slide心型移装，砂心移装core draw-back心轴，心骨arbor心座core bedding frame辛浦森式混砂机Sympson type sand mill新炼金属virgin metal新砂new sand锌(Zn) zinc锌当量zinc equivalence，zinc equivalent factor 通气口air port通气蜡条vent wax通气蜡线wax vent通气砂心blind core通气筛嘴(砂心盒) screen vent通气性vent ability通气针vent former通气针vent wire同素异性allotropy同位素isotope同质多象polymorphism桐油China wood oil酮油tung oil铜(Cu) copper铜基合金cupro-metal铜绿green patina铜气脆性(铸疵) hydrogen brittleness of copper 铜缘patina铜缘Verdigris筒状浇口(压铸) end gate头等品质top grade quality透明片transparent cut透气性permeability透气性试验permeability test透气性试验器permeability tester"凸出块，突耳casting lug凸疵(铸疵)(模型粘砂) sticker凸肩导销shoulder guider pin凸块，突耳lug凸片，飞边fin凸片管finned tube凸片气缸finned cylinder凸缘flange凸缘抹片flange sleeker突出标志rising mark突耳孔lughole突起分模面undulating mold joint涂焊(表面硬化涂焊) surfacing涂黑blacking涂浆，洗涤washing涂沥表管tarred pipe涂料facing materials涂料wash material涂料，涂模剂coat涂料，涂模剂coating涂料疤(铸疵) blacking scab涂料孔(铸疵) blacking hole涂模浆mold wash涂模浆molding wash涂模料mold coating涂模料mold dressing涂模料mold facing涂模料接种法mold coating inoculation涂刷painting土状石墨amorphous graphite吐粒散铁，吐粒散体trosstite钍(Th) thorium推拔，斜度taper推拔砂箱taper flask推拔套箱taper case推车式浇桶buggy ladle推挤(压铸) squeezing退火annealing退火罐annealing pot退火炉annealing furance (oven)退火温度annealing temperature退火箱annealing box退火用填料，退火用矿粉annealing ore退货rejection托板pallet托板输送机pallet conveyor托板输送机plate conveyer托架bracket托运板carrying plate脱件销(压铸) sprue puller pin脱蜡burn-out脱蜡dewaxing脱蜡法lost wax process脱蜡造模法lost wax molding脱裂强度(模砂式模纵面压裂试验) splitting strength 脱硫，去硫desulphurization脱硫，去硫desulphurizing脱模pattern draw脱模式造模机pattern-draw molding machine脱湿剂(模砂用) humectant脱碳decarburization脱碳法展性处理malleablization by decarburizing 脱碳率rate of decarburization脱硅desiliconizing脱锌dezincification椭圆导套oval bush外观检查outer inspection外角抹镘square sleeker外卡钳outside calipers外冷激，外冷硬，外冷铁extenal chill外模破裂broken mold外伸砂心顾clearance print外伸砂心头over-hang外伸余度砂心头clearance taper print外缩(铸疵) draw外缩孔(铸疵) open cavity外缩孔(铸疵) surface shrinkage外缩孔，凹陷(铸疵) depression外缩窝shrinkage depression外烯式空气预热器externally fired hot blast heater 外因非金属杂物exogenous non-metallic inclusion 外因金属夹杂物exogenous metallic in clusion外因凝固exogenous solidification外圆角round弯曲负荷bending load弯曲试验bending test弯头抹刀bent spatula完工面finished surface完全冷激complete chill完全燃烧complete combustion完全退火full annealing完整模型comple。
最全铸造学专业英语词汇
铸造学专业英语词汇A.F.S.粒度指数A.F.S grain fineness numberASTM弯曲试杆arbituration barA型石黑A type graphtieB型石墨B type graphiteCO2造模法，二气化碳造模法CO2process，carbon dioxide process DM转炉DM converterF.S.造模法，流砂造模法F.S.process，fluid sand mixture molding process F-M造模法，全模法F-M process，full-mold processLD(转炉盗氧炼钢)法LD processLD转炉LD converterL形吊骨jaggerN造模法，西山氏硬化法N-ProcessPH值，离标值pH valueSAE钢SAE steelS形钩S hookX光(X射线)，检验X-ray inspectionX光(X射线)，绕射线X-ray diffraction methodX光(X射线)，透视法X-ray radiographyX光(X射线)，显微分析器X-ray microanalyserX光，X射线X-rayX脱模法(包模铸造法)(三氯乙烯蒸气脱蜡)X-processY合金Y-alloy阿达麦辊Adamite roll阿伐固溶体alpha(a)solid solution阿伐黄铜alpha(a)brass阿伐青铜alpha(a)bronze阿伐铁alpha(a)iron阿姆可铁，工业级纯铁Armco iron埃(10-10米)Angstron unit埃鲁电弧炉Heroult electric arc furance艾氏冲击试验Izod impact test艾氏冲击试验机Izod impact testing machine艾素丘法Isocure process爱玛炉(碳化硅电阻炉)Elema furnace安定化退火stabilizing anneal安全布置safety layout安全护目镜safety goggles安全帽helmet安全设施protection and safety equipment安全限应力proof stress安全楔safety wedge岸砂shore sand按钮选择push button selection胺基甲酸乙脂urgthane胺类amine胺气amine gas暗冒口blind feeder暗冒口blind head暗冒口blind riser暗冒口bob暗冒口closed riser盎司合金(85-5-5-5铜合金)ounce metal凹口notch凹口半径radius of notch凹口感度notch sensibility凹口试片notch bar凹口试片notched bar凹口作用notch effect凹陷(铸疵)sink head巴氏合金Babbitt metal扒炉渣raking out the slag扒渣slagging off扒渣slag-off扒渣，结渣slagging拔模螺丝pattem screw拔模斜度pattern draft钯(Pd)palladium白[口]生铁white pig iron白[口]铸铁white cast iron白[口]铸铁white iron白粉料(涂模用)white facing白合金white metal白金，铂(Pt)platinum白黏土white clay白铁皮，锌板zinc plate白心展性铸铁(白心可锻铸铁)white heart malleable cast iron 白杨木poplar白缘(黑心展性铸铁)pearlite rim白云，母石黏土illite clay白云石dolomite白云石magnesia limestone白云石砖dolomite brick百万分之一ppm柏努利定理Bernoulli's theorem柏思麦酸性转炉生铁Bessemer pig iron柏思麦转炉Bessemer converter摆m线(造模)storing line斑面(铸疵)pitting surface斑蚀，点食pitting搬运，手操作handling板board板片捆sheet pack板手spanner板条结构模型grounds and lags板条输送机slat conveyor半合成模砂semi-compounded molding sand 半焦semi-coke半径radius半静钢semi-killed steel半离心铸造法semi-centrifugal casting半龙门起重机semi-goliath crane半圈补给口half-feeder半熔未型撑unfused chaplet半软钢semi-mild steel半硬钢medium hard steel半永久铸模semi-permanent mold棒磨粉机bar mill棒状砂心slab core磅/平方吋PSI(1bs per square in)包晶变态peritectic transformation包晶反应peritectic reaction包曼试验Baumann test包模涂料precoating material包模造模法investment molding包模铸造法investment casting包贴en-casement包析peritectoid包析反应peritectoid reaction剥落spall剥落spalling剥落，剥皮peeling剥砂痕(铸疵)rat tail剥砂面(铸疵)buckle剥砂线(铸疵)sand kneader保持时间holding time保持温度holding temperature保磁力coercive force保护蒙气protective atmosphere保护手套protective glove保温电力holding power保温净化，焖热，均热soaking保温净化，焖热烧透均热stewing保温炉holding furnace保温炉receiving furnace保险杠，缓冲器bumper保证试验proof test饱和度degree of saturation饱和度saturatin degree爆炸状石墨exploded graphite贝他黄铜beta(B)brass贝他石墨beta(B)graphite贝他铁beta(B)iron背板backpa backplate，die cast背板榇砂造模法back plate molding背层泥浆back-up coating slurry背砂back sand，back-up-sand背砂backing sand背压back pressure备用砂心条stock core钡(Ba)barium本智周万物夹渣(由金属本身引成)endogenous slag inclusion 畚箕，篮basket崩散collapse崩散性collapsibility绷索rope比电阻specific resistance比例碱度proportional basicity比例限界limit of proportionality比例限界proportional limit比热specific heat比色定量分析colorimetric analysis比色定量学colorimetry比色高温计color comparator pyrometer比色计colorimeter比色温度color temperature比重specific gravity闭附气occluded gas铋(Bi)bismuth边材(木材)sap wood边线，轮缘，胎环rim边线效果eddge effect边续式台车轮模机car type mold conveyor扁块，平板slab扁刷flat brush扁形进模口flat gate扁凿flat chisel变<<hap003>>铁，变<<hap003>>体bainite变态transformation变态[温度]范围transformation range变态点transformation point变态温度transformation temperature变态温度transition temperature变态温度范围transformation temperature range 变形deformation变形模型distoted pattern变形铸件strained castings变质剂leavening agent杓dipper杓，小铲scoop标称定律nominal rating标称应力nominal stress标称直径nominal diameter标称资本nominal capital标点gage point标点(抗拉试样)gage mark标距gage length标准成分，标准分析法standard analysis标准模型standard pattern标准砂standard sand标准试样standard sample标准预测值normal expected value标准圆筒试样(模砂)standard cylindrical specimen 标准砖standard square[bick]表面保护surface protection表面处理surface treatment表面粗糙(铸疵)rough surface表面浮松(铸疵)scum defect表面光制surface finish表面烘干skin drying表面烘干模skin dried mold表面烘干砂模flared mold表面烘干砂模roast sand mold表面冷硬surface chill表面烧着furface vitrification表面硬化case hardening表面硬化surface hardening表面针孔(铸疵)surface pinholes冰晶石cryolite冰糖形断面(铸疵)rock candy[fracture]丙铜acetone丙烯树脂acrylic resin并流parallel flow波来铁，波来体pearlite波来铁展性(可锻)铸铁pearlite malleable iron 波来铸铁pearlite cast iron波美Baume波美比重计Baume's hydrometer波纹ripple玻璃过滤器glass fabric filter玻璃化virtrification玻璃纤维glass fiber玻璃纤维布glass cloth勃氏硬度Brinell hardness勃氏硬度试验Brinell hardness test薄壁铸件thin section castings薄壁铸件thin-wall cstings薄型砖split brick捕尘器arrester补偿导线compensation lead补充焦coke booster补充焦炭，补充煤焦extra coke补给，进料，补浇feed补给环feed ring补给距离feeding distance补给口(冒口)feeder补给口带feeding zone补给口发热剂exothermic feeding compound 补给口发热剂(冒口)feeding compound补给口套feeder bush补给口效果feeder effect补给用冒口feed riser补浇repouring补强带，炉箍strengthening band补绕(冒口)feeding补缀，补修，补修料patch补缀，补修，搪补patching不规则合模面irregular joint不规则形分模面stepped joint不合尺寸off-dimension不良件数，退件数rejection number不良品rejects不良铸造faulty casting不列颠合金Britania metal不熔[化]性infusibility不透气性impermeability不稳定平衡图unstable equilibrium diagram 不锈钢stainless steel部分还原铁矿partially reduced iron ore部分混合性partial miscibility部分模型department pattern擦光buffing擦光机buffing machine擦光剂buffing compound擦光轮buff擦光轮buffing wheel擦伤galling材料试验material test材料试验material testing材料试验机material testing machine采购部purchase department采购价，原价purchase price踩紧track tramping参考分析reference analysis参数parameter残磁residual magnetism残留波来铁residual pearlite残留尘量residual dust content残留磁气remanent magnetism残留活斯田铁retained austenite残留金属液remaining melt残留强度(铸砂)retained strength(sand)残留物residue残留物，筛留物residues残留雪明碳铁residual cementite残留应变residual strain残留应力residual stress仓bin仓储storage仓库store house操作，作业operation操作钮operating knob糙斑铁，糙斑体sorbite糙斑铁铸铁sorbitic cast iron槽(槽型炉)loop槽带输送机trough conveyor槽形感觉电炉channel typee induction furance 草绳braided straw草绳straw rope草图sketching侧流道side runner侧冒口side riser侧装机side loader测高温学pyrometry测厚黏土thickness piece测深尺depth scale测深规depth gage测微放射线像microradiography测温漆thermal paint测隙规，厚度规thickness gage层，片lamella层焦coke charge层流laminar flow层状波来铁laminar pearlite层状腐蚀lamellar corrosion插模钉sprag查马克(商品名，压帮用锌铝铜合金)Zamak茶壶嘴式浇斗tea pot spout ladle搀炉，秋千炉，倾转熔铁炉tilting cupola铲，砂铲shovel铲斗shovel loader长柄导杆long shaft pendulum tool长抹刀，柳叶抹刀long spatula长石feldspar长统手套gauntlet glove长焰煤long flame coal长凿long chisel常态分布normal distribution常温裹贴法cold coated process常温试验cold test常温自硬air setting常温自硬法air set process常温自硬黏接剂air setting binder常温自硬树脂粘结风airbond常温自硬性合成树脂cold-hardening synthetic resin 常温自硬性黏结剂cold-setting binder常温自硬油air setting oil常温自硬铸造模air setting mold场内熔接shop weld敞模，露天模open mold敞模铸造open sand casting敞砂模open sand mold敞砂模法open sand molding超高电力super-high power超轻合金ultra-light alloy超细粉sub-sieve powder超音波检验ultra-sonic testing车car车床lathe车床床身，车床床台lathe bed车屑turning scraps车屑turnings尘量测定器dust extraction device榇边bush，bushing榇垫，填料packing榇炉用期lining campaign榇砖lining brick成本cost成本prime cost成长rowth成堆比重bulk specific gravity成堆密度bulk density成堆容积bulk volume成孔期(电弧炉)，搪孔boring成模台(压铸)holding block成品量，产量output成品铸件区finished castings department成熟度degree of normality成形forming成形性forming property程序图routing routing diagram弛力退火stress relief annealing池，浴槽bath持久比endurance ratio持久试验endurance test持久性endurance匙形抹刀slicker spoon迟延装置delay screen尺，规则rule尺寸dimension尺寸安定性dimensional stability尺寸精度dimensional accuracy齿轮吊车浇geared crane ladle齿轮缘gear rim赤铁矿hematite赤铁矿生铁hematite pig iron，hematite iron赤杨木alder充氮nitrogen charge冲砂(铸疵)cut冲砂(铸疵)cuts冲砂(铸疵)cuts and washed冲砂(铸疵)，涂浆wash冲蚀erosion冲蚀结疤(铸疵)erosion scab冲板洗涤机impingement plate scrubber冲层stampings冲床，冲头punch冲击磨耗pounding wear冲击强度impact strength冲击式硬度试验机impact hardness testin machine 冲击试验impact test冲击试验机impact tester冲击速度striking velocity冲击值impact value冲孔废料punched scrap冲射射式集尘器impingement dust collector冲销drift冲屑punchings虫lac虫胶shellac抽取用皮带输送机draw off belt conveyor抽吸罩suction hood抽吸装置sucking-off plant抽烟气设备fume extraction equipment抽样sampling抽样规则sampling prescription抽样检验samplimg inspection稠渣sluggish slag出口outlet出模机构knock-out gear出气管(旋风集尘器)exit pipe出清(熔炉)depletion出铁tapping出铁杆tap out bar出铁杆tapping bar出铁口，流出孔tapping hole出铁口熔渣flux出铁口塞杆tap hole plug stick出铁温度tapping temperature出渣slag-out出渣，脱渣deslag，deslagging出渣槽slag notch出渣槽slag spout出渣槽slagging spout出渣孔scum hole出渣孔slag hole初步清理台rough dressing table初步试验preliminary test初级线圈primary air初加料，起熔料initial charge初晶primary constituent初晶活斯田铁proeutectic austenite初晶石墨primary crystal初裂incipient crack初凝结initial condensation初生吐粒铁primary troostite除尘dedusting除尘dust extraction除尘器dust separator除尘设备dust removal除尘设备dust removal plant除尘装置dust separation plant除铝剂aluminium removal除气degasification除气degasifying除气degassing除气剂degasifier除气熔剂degassing flux除气退火degassing anneal除氢，脱氢degassing of fydrogen除湿dehumidification除湿，脱水，干燥dehydration除湿器dehumidifier除渣drossing除脂degreasing储仓bunker储仓silo储仓storage bunker处理楔值processing wedge value处理用浇桶theatment ladle穿透，贯穿penetration穿透能力(X光试验)penetrating power 船用钢板ship plate传导度conductivity传递气carrier gas传递液carrier fluid传热流体thermal fluid吹板(吹砂机)blow plate吹板(吹砂机)blowing plate吹疵blow吹风淬火air blast quenching吹管blow-pipe吹净用空气(冷厘法)scavening air吹气，通气处理(金属液)，冲洗flush slag吹枪blow gun吹砂机(造砂心用)blowing machine吹氧炼钢法oxygen steel making吹氧嘴管oxygen lance吹制砂心blow a core吹制砂心blowing吹制砂心blown core吹制用砂心盒core box for blowing锤hammer锤鳞，鍜鳞hammer scale锤平，轻敲peening锤球，落锤球tup锤碎机hammer mill纯度degree of purity纯度purity纯铁pure iron瓷土，高岭土china clay磁粉探伤magnetic particle inspection，magnetic crack detection 磁化力magnetizing force磁力带轮(磁选机用)magnetic pulley磁力探伤magnzflux磁力探伤检验magnaflux inspection磁力探伤检验magnetic crack detection磁力筒(磁选机用)magnetic drum磁力造模法magnet molding process磁铁矿magnetite磁性变态magnetic transformation磁选机magnetic separator磁滞损失hysteresisloss枞木fir粗度，粗糙度roughness粗钢raw steel粗晶面(铸疵)facet tracture粗粮波来铁coarse pearlite粗面凝固rough wall solidification粗磨snag粗磨机rough grinding machine粗泥浆砂roughing loam粗砂coarse sand粗砂roughing sand粗砂锥辗硅砂concial sand from coarse sand粗筛riddle粗松组织coarse structure粗松组织open-grain structure粗铜blister copper粗轧辊roughing roll催化剂accelerator催化剂，触媒，冷化剂catalyst脆化embrittlement脆性brittleness脆性shortness淬火quenching淬火机hardening machine淬火裂痕quench crack淬火裂痕quenching crack淬火能力(淬火液)quenching intensity淬火时间quenching time淬火时效quench aging淬火应力quenching stress淬火硬化quench hardening淬裂hardening crack错模，偏合，毛边(铸疵)，工作班制shift错配(模型，铸模，心型)mismatch，in pottern mold，core 鎝(Tc)technetium打包机packer打孔卡片punch card打孔纸带puch tape打磨(磨毛边，打浇冒口等)fettle shagging打磨滚筒rattler打散筛孔breaker screen打铁球skull cracker打铣球，落锤drop ball大浇斗bulbs大气，蒙气(炉内气氛)atmosphere大气泡(铸疵)gross blowhole大气熔化air melting大气铸造air casting大型铸件large castings带band带，皮带belt带锯band saw带色防护镜filter glass带式磁选机magnetic belt separator带式运送机belt conveyor带铁fillet iron带缘导销collared pin带运送机band conveyor袋滤器bag filter袋滤器bag house袋形端承pocket print单边心型端承，单边砂心头single core print单轨系统monorail system单件模型one-piece pattern单面模型板single-strand casting machine单色光学高温计monochromatic optical pyrometer 单体肥粒铁free ferrite单体碳free carbon单体雪明碳铁free cementite单条[连续]铸造机sink单位负载unit load单向凝固unidirectional solidification单元砂，整体砂unit sand单支进模口本堰single gate氮硬化nitrogen hardening氮(N)nitrogen氮化nitriding氮化法nitriding process弹动清砂spring release弹簧心型撑spring chaplet弹能模数modulus of resilience弹壳黄铜(三七黄铜)cartridge brass弹性elasticity弹性变形elastic deformation弹性模数，弹性系数elastic modulus弹性能resilience弹性切割砂轮elastic slitting wheel弹性系数，弹性模数modulus of elasticity弹性限界elastic limit弹性限界limt of elasticity当量，等价系数coefficient of equivalent挡板baffle挡板baffle plate挡板damper挡渣坝dam挡渣口浇桶dam type lip ladle档渣浇池pouring basin with buffles刀形进模口knife gate倒角，去角rounded sand grain捣成炉榇rammed lining捣成用料ramming compound捣动盛桶(脱硫用)shaking device捣紧，填塞剂tamping捣紧度，槌紧度degree of ramming捣砂，捣制rramming捣砂锤bench rammer捣砂锤rammer捣砂杆sand rammer捣砂走样ram off捣制砂心ram up core捣制走样ramaway导股(连续铸造)strand guiding导气管air duct导入，导件guide导套guide bushing导销guide pin导销leader pin导销榇套leader pin bushing得板screen plate德拉瓦离心铸管法De-lavaued processdelay relase 德他固溶体dendrite德他合金delta solid solutin德他黄铜delta bronze德他青铜delta iron德他铁delta metal德银，铜German silver等吹熔铸炉equi-blast cupola等价因子equivalence factor等温变态isothermal transformation等温退火isothermal annealing等温线图isothermal diagram等温硬化isothermal hardening低合金钢铸件low alloy steel castings低磷生铁low phosphorus pig iron低摩擦金属anti-friction metal低黏天然砂meager sand低黏性砂lean sand低黏性砂weak sand低黏性硅砂，硅砂unbonded silica sand低碳钢low carbon steel低碳生铁low carbon pig iron低温脆性cold shortness低温熔化cold melt低温退火low temperature annealing低压风扇low pressure fan低周波main frequency低周波感应电炉line frequency induction furnace低周波感应电炉low frequency electric induction furance迪沙式自动造模机(丹麦制高压高速无箱式造模机)Disamatic molding machine 底(炉)，(造模)bed底板acking board底板bed plate底板bottom board底板bottom plate底层装料bed charge底焦coke bed底浇法bottom casting底浇法bottom pouring底浇式浇桶bottom pour ladle底浇铸模bottom pour mold底进模口法bottom gating底面basal plane底炭bed coke底炭高度bed coke height底特律式电弧炉Detroit electric furnace地坑pit地坑炉pit furnace地坑造模法pit molding地坑铸造pit casting地面砂，背砂floor sand地模floor mold地模法，地面造模法floor molding碲(Te)tellurium碘(I)iodine点火firing点火ignition点火ligh up点火lighting up点火light-off点火孔breast door点火孔lighting hole点火器igniter点燃点ignition point电池，组battery电磁搅拌electric magnetic agitation电磁循环electric magnetic circulation电动吊车electric hoist电动发电机motor generator电动加气硬化机automatic gassing machine电动推高机electric lift truck电动造模机electric molding machine电镀electro-gilding电镀electro-plating电焊条，电熔接条arc welding electrode电弧长度arc length电弧截割arc cutting电弧炉arc furnace电弧炉electric arc furance电弧气吹铲平arc-air gouging电弧气吹切割arc-air cutting电弧熔接arc welding电弧熔接，电焊electric arc welding电极，电熔接条，电焊条electrode电极耗用量(电弧炉)electrode consumption电极夹具，电熔接条夹把，电焊条夹把electrode holder 电极控制系统electrode control system电极清洁法electrol-cleaning电极熔接，电极焊接electrode welding电极头stub end电解精炼electrolytic refining电解铁electrolytic iron电解铜electrolytic copper电解锌electroplytic zinc电开关装置electric switchgear电炼生铁electric furance iron电炉electric furance电炉钢electric steel电滤尘器electro-filter电木，胶木bakelite电热熔化electric smelting电子electron电子显微镜electron microscope电阻高温计resistance pyrometer电阻合金electro-resistance alloy电阻炉electric resistance furance电阻炉resistance furnace电阻系数，电阻力resistivity垫板，底板base plate垫厚(铸造技术)padding，reinforcement垫厚(铸造技术)reinforcement，paddling垫圈，洗涤机washer淀粉starch吊车hoist吊车浇桶crane ladle吊车盘hoist pan吊钩lifting hook吊骨，撑条，插条gagger吊骨，撑条，插条slodier吊骨，吊具，吊架hanger吊环bail吊梁lifting beam吊砂条clack吊运车trolley吊钩load hook吊骨anchoring调合模砂blended molding sand调节设备controlled means调辙车transfer car调整器regulator调质处理quenching with Subsequent tempering 调质砂tempering sand调质水分tempering water调质铸铁modified cast iron蝶形阀butterfly valve迭边浇道Connor runner bar迭边进模口kiss gate迭边进模口lap gate迭边冒口kiss riser迭模multiple mold迭模stack boxes迭模stack mold迭模法multiple molding迭模法stack molding迭模浇铸法stack pouring迭箱stack钉nail顶板ejection plate顶板lifting plate顶板top board顶板top plate顶出ejection顶出板(压铸)ejector plate顶出杆knock-out bar顶出力ejector force顶出器，喷射器ejector顶出销knock-out pin顶出销(压铸)ejector顶浇法top pouring顶浇进模口top gate顶冒口top riser顶销，起销lifting pin顶铸法top casting process定量分析quantitative analysis定量仪quantometer定模(压铸)cover die定模板(压铸)，平台platen定盘式混砂机fixed pan mill定时淬火time quenching定时器timer定位垫locating pad定位孔locating hole定位销locating pin定位销钉positioning dowel定位锥locating cones定心毂centering boss定心针centering pin定性分析qualitative analysis订货铸造工场jobbing foundry铥(TM)thulium冻汞法(精密铸造)Mercast process动力滚子输送机powered roller conveyor 动力试验dynamic test动叶轮impeller动叶轮摔砂impeller ramming动作，工作working都市煤气town gas陡震试验shock test斗，箕斗，桶装载机bucket毒性度toxicity rating读数式分光仪digital spectrometer堵口砖nozzle brick堵塞bott堵塞botting堵塞出铁口(熔铁炉)stopping up堵塞杆bott stick堵塞器stopper堵塞式浇桶stopper ladle堵塞砖stopper and nozzle brick杜具纳转炉Tropenas converter杜维利化碳转浇铸法Durville pouring杜维利化碳转浇铸法Durville process镀镍nickel plating镀锡铁皮，马口铁皮tin plate镀锌galvanizing镀锌sherardizing镀锌zinc coating镀锌zinc plating镀锌，浸锌zinc galvanizing镀锌脆性galvanizing embrittlement镀锌铁板，白铁皮galvanized iron sheet 镀锌铁皮，白铁皮zinc-coated sheet短暂退火炉short anneal furnace锻造用合金wrought alloy断口检验fracture test断口金相检验fractography断裂点point of rupture断面收缩necking断面缩率area contraction，percentage of 断面缩率area reduction，percentage of断续浇铸interrupted pouring堆heap堆高机fork lift truck堆积密度packing density堆料场stock ground堆料场stock-yard堆砂heap sand堆渣场slag tip堆重piled weight对合开放砂心盒split open ended core box 对合模型，分割模型split pattern对合模型板，分割模型板split plate对合铸模split mold对流convection对准alignment钝气inert gas钝气电弧熔接inert-gas arc welding多边形筛polygonal screen多段风口，多段风嘴multiple tuyere多角形砂angular sand多孔塞porous plug多孔塞搅拌法porous-plug method多孔性，气孔率，气孔巢(铸疵)porosity多石英砂quartzose sand多水高岭土halloysite锇(Os)osmium鹅颈浇道，鹅颈管goose neck而酸铸铁acid resistant cast iron耳轴，挂耳trunnion二次风口，二次风嘴secondary tuyere二次合金secondary alloy二次空气secondary air二钙硬化法Di-Cal process二氧化锆zirconia二氧化碳造模法，碳酸气硬模法，CO2造模法carbon dioxide process(CO2process)二氧化铁(FeO2)ferrous oxide二元合金binary alloy发火合金pyrophoric alloys发热反应exothermic reaction发热覆盖?冒口用)exothermic shield发热冒口exothermic riser发热套筒exothermic sleeve发热性缩颈砂心(冒口用)exothermic breaker core发热性缩孔防止粉exothermic antipiping powder发生炉producer发生炉煤气power gas发生炉煤气producer gas发生炉燃气，瓦斯generator gas阀valve珐琅面，上釉glassy surface翻举装置rollover and lifting device翻模rolling over翻模板rollover board翻模板rollover plate翻箱索具beam and sling翻箱造模机rollover molding machine翻转(壳模制造)peel back翻转，翻模rollover翻转顶销脱模机turnover and pinlift machine翻转式砂心机rockover core making machine翻转脱模式造模机frame-rollover machine翻转脱模装置turn-draw device翻转造模机turnover molding machine钒(V)vanadium钒铁ferro-vanadium钒铸铁vanadium cast iron反复冲击试验repair反复横断冲击试验repeated impact test反喇叭形浇口reverse horn gate反射炉air furnace反射炉reverberatory furnace反跳硬度计scleroscope反跳硬度试验rebound hardness test反跳硬度试验scleroscope hardness test反斜度back draft反应带reaction zone反应度reactivity反应模斜度inverse draft反应速率rate of reaction反转起模draw on turnover方锉square file方解石calcite方向性凝固directional solidification防尘面具，口罩respirator防护套管protection tube防裂筋cracking strip防裂片，散热片cooling fin防蚀anti-corrosion防缩暗冒口shrink bob防缩剂，冒口保温用anti-piping compound 防缩孔粉剂pipe eliminator防缩冒口shrink head防缩冒口shrinker防锈anti-rust防锈剂rust-preventing agent防锈涂层rust preventive coating放射线检验radiographic inspection放射线检验radiographic testing放射线透视radioscopy放射线照片radiographic film放射线照像术radiography放射性同位素radioactive isotope放样板lay out board放置器set-down device非磁性铸铁non-magnetic cast iron非焦性煤non-coking coal非金属夹杂物non-metallic inclusion非金属夹杂物sonims非均质组织heterogeneous structure非破坏试验non-destructive testing(NDT)非铁金属non-ferrous metal非氧化气孔(银白色气孔)(铸疵)unoxidized blowholes 飞边(铸件)feather飞边，闪光flash飞边清除flash removal飞边现象(合模或模裂形成)finning飞灰fluxing肥粒铁，肥粒体ferrite肥粒铸铁ferritic cast iron沸腾boil沸腾boiling沸腾期boiling period肺尘埃沉着病pneumoconiosis费德曼组织(金相)Widmannstaetten structure废(钢)片sheet scrap废电极electrode scrap废钢scrap steel废料scrap废品率arate of rejects废品率，退件率，不良率reject ratio废品率，退件率，不良率rejection rate，reject atio 废气exhaust gas废气waste gas废热waste heat废铁iron scrap废铁scrap iron废铸料cast scrap分布distribution分部模型section pattern分部心型sectional core分层浇口side step gating分层进模口side step gate分层精炼法zone refining分次式混合机batch mixer分次式火炉batch type annealing furnace分次式磨粉机batch mill分次式配砂场batch sand plant分次式熔炉batch furnace，batch-type furnace)分次退火炉periodic annealing furnace分道砖runner core分度盘dividing plate分度圈limb分段淬火interrupted quenching分段淬火stage hardening分段淬火step quenching分段时效interrupted aging分段退火stepped annealing分级，刻度graduation分级节(模砂)classifying screen分级进模口steeped sprue分级进模口step gate分级进模口stepped side gate分级进模口铸造step gate casting分级筛grading screen分级筛size screen分级摇动筛size jigging screen分级硬度gradient hardness分件图parts drawing分解resolution分离器separator分离筛sepaating screen分离型波来铁(球状云明碳机)divorced pearlite 分模粉parting powder分模剂parting agent分模剂parting compound分模面mold joint分模面parting surface分模面进模口parting gate分模砂parting sand分模线parting line分模纸parting paper分配流槽distributing launder分配销(压铸)sprue pin分支砂心，分支心模branch core分铸试验separately cast test bar分子molecule酚phenol酚<<an017>>喃树脂phenolic furan resin酚甲醛树脂phenol-formaldehyde resin酚树脂phenolic resin酚塑，黏结剂phenol plast binder粉煤powdered coal粉煤pulverized coal粉煤装置powdeed coal equipment粉末金属powdered metal粉末金属机件powdered metal parts粉末冶金，粉末冶金术powder metallurgy粉状石墨plumbago封闭sealing封闭剂sealing compound封闭砂条sealing ring封罐退火pot annealing封合模型，分割模型parted pattern封盒退火box annealing封漏，浸入impregnation风锤air hammer风管输送机pneumatic tube conveyer风管输送系统penumatic tube dispatch system 风化石锥辗硅砂conical sand from stone风口，风嘴tuyere风口棒tuyere bar风口比tuyere ratio风口带tuyere zone风口面buyere line风力分级air classification风力净化法air cleaning process风量，体积air volume风量计air volume meter风量计blast volume meter风量控制仪air weight controller风干air drying风干法air seasoning风干强度air strength风干强度air-dried strength风扇fan风速计anemometer风箱air belt风箱air box风箱air tank风箱wind belt风箱wind box风硬air hardening风硬钢air-hardening steel枫木maple蜂巢炉beehive oven蜂巢炉焦炭beehive coke蜂蜡bees wax伏利安[气体]搅拌法voianik method浮渣dross浮渣incrustation浮渣，夹渣scum浮渣，撇渣skim幅射高温计radiation pyrometer幅射管炉radiant tube furnace复合辊composite roll复合接种剂complex inoculant复合涂膜complex coating复合形砂compound sand复合铸造composite casting复磷repetition castings复热器recuperator复热系统recuperative system复置模型试模replacing pattern in the mold 复制品replica腐蚀corrosion腐蚀脆化corrosion embrittlement附件accessories附浇口系模型gated pattern附设铸工场capitive foundry附设铸工场tied foundry附体试杆cast-on bar附体试杆cast-on test bar附体试片test coupon附体试片test lug附体试验attached test coupon负偏析negative segregation负载load副产焦炭by-product coke副电流sedondary current副料indirect materials副线圈secondary coil腹板web覆盖热cover heating折心展性铸铁iron oxide covering覆盖层[熔剂],涂层covering flux钆(Cd)(烯土金属)gadolinium改良合金modified alloy钙(Ca)calcium钙系膨土calcium bentonite灰汁，碱水lye盖M法，疏塞气体搅拌法Gazal process坩埚crucible坩埚底座，垫砖stool坩埚式感应电炉coreless induction furance 坩蜗吊钳crucible lifter坩蜗法crucible process坩蜗钢crucible steel坩蜗浇铸装置crucible pouring device坩蜗炉crucible furnace坩蜗钳crucible tongs坩蜗涂浆crucible wash杆，棒，条bar杆盘松砂机spike disintegrator杆条矫直机rod straightener感应淬火induction quenching感应电炉electric induction furnace感应电炉induction furnace感应加热induction heating感应器inductor感应线圈induction coil感应硬化induction hardening橄榄石砂oliving sand刚铝，杜拉铝duralumin刚铝石alundum刚模半边(压铸)die half，die cast刚模钢die steel刚模试验(压铸)die try-out，die cast刚模穴(压铸模)die cavity刚砂emery刚性rigidity刚玉corundum纲丝netting wire纲状组织(金相)net-work structure钢steel钢厂steel works钢锭steel ingot钢坩埚steel crucible钢皮镁砖metal-case magnesite brick钢输送带steel conveyor belt钢水瓢，抹砂匙spoon钢水瓢测温法spoon test钢丝钳pliers钢丝刷wire brush钢丝索wire rope钢丝位wire cut钢条bar steel钢条steel bar钢线粒cut wire shot钢屑，废钢料steel scrap钢性铸铁semi-steel钢铸件steel castings高傲砂blended sand高级钢high-grade steel高级铸铁high class cast iron高级铸铁high grade cast iron高加波感应电炉，高频率感应电炉high frequency induction furance 高架磁选机overhead magnetic seperator高架单轨overhead monorail高架起重机gantry crane高拉力黄铜high tensile brast高拉力铸铁，高强度铸铁high tension cast iron高磷生铁high phosphorus pig iron高磷生铁phosphoric pig iron高岭石kaolinite高岭土kaolin高硫钢(易切钢之一种)sulphur steel高炉shaft furnace高炉，鼓风炉blast furnace高炉焦furnace coke高炉煤焦，鼓风煤焦blast furnace coke高铝红柱石mullite高锰钢Hadfield's manganese steel高锰钢铸件high manganese steel castings高黏土砂fat sand高黏土铸砂loamy sand高强度钢，高拉力钢high tension steel高强度黄铜high strength brass高强度铸铁high strength cast iron高碳钢high carbon steel高温淬火hot quenching高温计pyrometer高温耐火砖highly refractory brick高温强度(铸砂用)hot strength高温烧结high sintering高温试验hot test高温冶金学pyrometallurgy高硅生铁silvery iron高硅砖high siliceous brick高压罐bomb高压水清砂机hydro-blast高压造模法high pressure molding高氧化铝砖high-alumina brick高氧砖alumina brick高硬度钢glass hard steel高周波干燥，高频率干燥dielectric dry高周波干燥机，高频率干燥机dielectric dryer高周波砂心干燥炉hign-frequency core drying stove 搞压试验compression test锆(Zr)zirconium锆砂zircon sand锆石粉zircon flour锆英石zircon格子(结晶)lattice格子结构lattice structure格子筛分输送机grid type screening conveyor格子形耐火砖checker brick隔条砂箱barred box镉(Cd)cadmium铬(Cr)chromium铬钢chrome steel铬基耐火材料chrome base refractories铬克合金nichrome铬镁砂chrome-magnesite铬砂chromite sand铬砂hevi sand铬酸处理chrome pickle treatment铬酸处理(镁锌铸件镀铬)dichromate treatment铬铁ferro-chromium铬铁矿chromite铬铸铁chrome cast iron铬砖chromite brick给砂机sand expansion工地熔接site weld工具tool工具钢tool steel工具台tool table工模jig工资labor cost工作场所working aea工作大纲图表outline process chart工作路线排定rounding工作台working table。
铸造专业术语英文
铸造专业术语英文
铸造 (foundry) 是一种将熔化金属或其他材料倒入模具中，然后使其凝固和冷却以获得所需形状和尺寸的制造过程。
铸造是一种广泛应用的制造技术，用于制造各种零件和设备，例如汽车发动机零件、飞机部件、船舶零件、计算机零件和电子设备组件等。
以下是一些铸造专业术语的英文:
1. Foundry - 铸造厂
2. Furnace - 熔炉
3. Mold - 模具
4. Torch - 熔炉炬
5. Furnace gas - 熔炉气体
6. Iron ore - 铁矿石
7. Coal - 煤
8. Coke - 焦粉
9. Dross - 金属氧化物
10. Foundry process - 铸造过程
11. billet - 铸件
12. casting - 铸件
13. gating - 浇口
14. Shell - 壳模
15. foundry equipment - 铸造设备
16. float - 浮砂
17. draw - 拉砂
18. blow - 吹砂
19. malleable iron - 可铸铁
20. Hardened steel - 硬化钢
这些专业术语对于铸造工人、工程师和研究人员来说非常重要，因为它们用于描述铸造过程中的各种步骤和材料。
常用铸造术语中英对照
常用铸造术语中英对照2021-6-26整理(BY BARRY)Ⅰ.根本术语1.压力铸造die casting2.铸造casting,foundry,founding3.铸件casting4.毛坯铸件rough casting5.试制铸件pilot casting6.试模trial shot7.模具mold,mould8.压铸机die casting machine9.铸造设备foundry equipment,foundry facilities10.铸工caster,founder,foundry worker11.压铸工die carter12.铸造厂foundry13.铸造车间foundry shop14.铸造工作者foundry man15.批〔batch一批:a batch;每批:each batch, per batch);lot16.一炉a cast,a heat,a melt17.焊接welding18.铸造三废foundry effluent19.铸锭ingotⅡ.铸造合金、熔炼和浇注1.铸造合金cast alloy2.铝合金aluminium alloy3.铸造复合材料cast composite4.合金元素alloy element5.杂质元素tramp element6.碳化物carbide7.过热superheating8.过冷supercooling9.熔点melting point10.总碳量total carbon11.碳当量carbon equivalent12.碳当量仪eutectometer13.铝硅合金aluminium-silicon alloy14.压铸合金die cast alloy15.压铸铝合金aluminium diecast alloy16.压铸镁合金magnesium diecast alloy17.熔炼smelting18.熔化率melting rate19.元素增加gain of element20.熔剂flux21.熔池bath22.除气熔剂degassing flux23.覆盖剂covering flux24.炉料charging25.金属炉料metallic charging26.回炉料foundry returns 27.废金属料scrap28.熔渣slag29.沉渣sludge30.浮渣dross,scum,cinder31.造渣slag forming32.出渣deslagging33.出渣口slag hole34.炉衬furnace liner35.出炉口tap hole36.出炉温度tapping temperature37.重熔remelting38.坩埚炉crucible furnace39.保温炉holding furnace40.精炼refining41.真空精炼vacuum refining42.除气degassing43.残料heel44.浇注pouring45.自动浇注装置automatic pouring device46.浇包，料斗(勺)ladle47.转运包transfer ladle48.金属残液heel49.冷金属cold matelⅢ铸造工艺与工艺设备die casting process and process device1.铸造性能castability2.流动性fluidity3.充型能力mold-filling capacity4.充型速度(浇注速度)pouring rate;delivery rate5.充型时间filling time6.浇注温度pouring temperature7.比浇注速度specific pouring rate8.浇注时间pouring time9.凝固solidification10.凝固时间solidification11.收缩contraction;shrinkage12.收缩率shrinkage13.液态收缩liquid contraction14.凝固收缩solidification contraction15.固态收缩solid contraction16.液-固收缩liquid-solid contraction17.自由收缩free contraction18.收缩余量shrinkage allowance19.收缩应力contraction stress20.热应力thermal stress21.铸造应力casting stress22.残留应力(剩余应力)residual stress23.热裂倾向性tendency to hot tearing24.铸造工艺设计casting process design25.铸造工艺计算机辅助设计Computer-aided design for the casting process;casting process CAD26.实体造型constructive solid geometry;solid modeling27.充型分析mold filling analysis28.铸造工艺设备设计foundry tools design29.铸造工艺卡casting process card;foundry process card30.铸型装配图mold assembly drawing31.铸件图(毛坯图)drawing of rough casting32.铸造工艺准备preparation of casting technique33.铸件设计casting design34.铸件基准面reference face for machining of casting35.分型面parting face;(mold joint;mold parting)36.不平分型面irregular parting;(irregular joint;match parting)37.阶梯分型面stepped parting;stepped joint38.浇注位置pouring position39.交接壁intersection40.十字交接X-junction41.圆角fillet42.热节(点)hot spot43.加强筋stiffening ribs44.拨模斜度draft45.型腔mold cavity46.工艺孔technological hole47.浇注系统gating system;running system48.直浇道sprue49.横浇道runner50.内浇口ingate,gate51.溢流槽overflow well52.排气槽air vent53.分流锥sprue spreader;spreaderⅣ压力铸造〔特种铸造〕die-casting1.压铸机die casting machine2.冷室压铸机cold chamber die casting machine3.冷室卧式压铸机(卧式压铸机)horizontal(cold chamber)die casting machine4.冷室立式压铸机〔立式压铸机〕vertical(cold chamber)die casting machine5.热室压铸机hot chamber die casting machine6.真空压铸evacuated die casting;vacuum die casting7.压射injection;shot8.压射机构injection system9.压室injection chamber10.压射冲头injection ram;plunger11.压射速度injection speed12.压射比压injection pressure13.增压pressurization 14.充填率rate of filling15.锁型(合型)die locking16.合型机构(锁型机构)die closing mechanism17.锁型力die locking force;clamping force18.拉杆tie bar;tie rod19.压铸模die;die casting die20.定模(定型)fixed die;cover die half21.动模(动型)moving die;ejection die half22.浇口套sprue bush23.留型时间opening time24.顶出机构ejection mechanism25.顶杆ejector pin26.抽芯机构core puller27.余料biscuit;slug28.压铸涂料coating of diecasting;releaseagent29.充型压力mold filling pressure30.充型速度filling speed31.保压压力dwell pressure32.保压时间dwell timeⅤ压铸后加工及其工具1.喷砂清理sand blasting cleaning2.喷丸清理shot blasting cleaning3.抛丸清理wheel blasting cleaning4.滚筒清理tumbling5.抛丸清理机wheel blasting machine6.除浇口degating;trimming7.除毛刺deburring8.去氧化皮descaling9.打磨grinding10.弹丸shot11.抛丸器shot wheel12.喷丸器shot blaster13.砂轮机grinder14.浸渗处理impregnantion15.浸渗剂impregnant16.矫型rectification;straightening coining;17.外表处理surface treatment18.砂带打磨belt sanding19.钻孔;镗孔boring20.脱脂degreasing21.电镀electroplating;electrostatic coating22.夹具clamp;fixture23.机加工machining24.铣milling25.台式铣床bench milling machine26.数控加工中心CNC27.铸件机加工余量machining allowance of casting28.切削液mineral cutting oil29.抛光polishing30.粗加工rough working31.喷涂painting32.冲孔punching33.外表处理surface treatment34.洗净rinse35.车床lathe36.磨床grinder,grinding machine37.铣床milling machine38.钻床drill press39.刨床planerⅥ检测方式/设备/工具量具inspection equipment/facility1.合格质量水平acceptable quality level(AQL)2.气密性试验air tightness test3.大气暴露试验atmospheric corrosion test4.成分分析试验chemical analysis5.破坏性检测destructive inspection6.非破坏性检测nondestructive inspection7.尺寸检测dimensional test8.硬度试验hardness test9.冲击试验impact test10.逐件检查individual check11.抽样检查sampling inspection12.三座标检测microcode13.耐压试验pressure test14.盐雾试验salt spray test15.盐雾试验机salt spray test machine16.拉力测量机tensile test machine17.平面度检测仪flatness inspection guage18.检漏机leakage test machine19.普通检具normal guage20.抽样检查sampling inspection21.耐气候试验weathering test22.x光探伤x-ray test23.X光机X-ray machine24.塞规plug guage25.丝攻screw tap26.锥度规conical guage27.螺纹塞规thread plug guage28.游标卡尺vernier caliper29.半径规radius guage30.测角器/量角器bevel guage31.测径规,厚簿规calliper guage32.高度尺height guage33.深度尺depth guage34.三座标CMM35.光谱仪spectrographⅦ.包装packaging1.护边edge protection2.中间夹层intermediate layer3.多插入口式托盘multiple-entry pallet4.一次性托盘throw-away pallet5.耐气候wether resistanceⅧ图纸相关Drawing Related1.喷砂清理abrasive cleaning2.研磨剂abrasive3.依据according to/Acc to4.阳极氧化anodic oxidation5.外观appearance6.踏板autowalk pallet7.底座基座基准base8.盲孔blind hole9.气孔,气泡blow hole10.孔径hole diameter11.凸台boss12.基准面datum plane13.模定位面cast locator datum plane14.铸造应变casting strain15.中心孔center bore16.外圆角,倒角chamfer17.内圆角fillet18.同心度concentricity19.平面度flatness20.平行度parallel21.粗糙度roughness22.垂直度perpendicularity23.清洁度cleanness24.符合conform to25.残留物，污物contamination26.抽芯孔,铸孔core hole27.耐腐蚀corrosion resistance28.沉孔counterbore29.盖板cover30.关键尺寸critical dimension31.横切试验cross-cut test32.脱炭decarburize33.拔模斜度draft angle/draft34.导电性electric conductivity35.电动扶梯梯级escalator step36.外径〔大径〕external diameter37.内径(小径)internal diameter38.外螺纹external thread39.加工余量machining allowance40.法兰flange41.披锋flash42.自由状态free state43.通用公差〔未注公差〕general tolerance44.符合in accondance with45.来料检验incoming inspection46.标识indication,marking47.绝缘性isolation characteristics48.金属互化物intermetallic compound49.内螺纹internal thread50.每per51.边缘periphery52.永久伸长permanent stretch53.垂直于perpendicular to54.针孔，销孔pin hole55.平面图plan,plane figure56.磨光剂polish agent57.聚酯纤维polyester58.容许应力proof stress59.剩余应力residual stress60.试生产铸件prototype casting61.质量保证quality assurance62.散热器radiator63.耐磨性resistance to abrasion64.肋；筋条rib65.滚丝攻通roll thread thru66.剖面图section67.模具寿命service life of dies68.螺距pitch69.阴影毛坯区域shaded area cast70.收缩shrink71.缩孔shrinkage porosity72.碎片sliver73.烧伤soldering mark74.标准standard/std.75.强度范围strength division76.分层;剥落stripped mark;peeling77.清理外表;外表加工;外表抛光surface finish78.抗拉强度tensile strength79.未注unless otherwise specified/unspecified/unmarked80.凸纹/直纹vein grain81.壁厚wall thickness82.屈服点yield pointⅨ压铸报价Quotation1.适用检测标准acceptable inspection standard2.压铸附加费additional casting cost3.铸造费用casting cost4.折扣价depreciation expenses5.估价estimated price6.离岸价free on board(FOB)7.到岸价cost insurance freight(CIF)8.信用证letter of credit(LC)9.后加工费finishing cost10.定率法fixed rate method11.先行生产go-ahead of produce 12.铝锭价格ingot price13.插件费insert cost14.检测费inspection cost15.熔炼费melting cost16.制造间接(额外)费overhead manufacturing expense17.附加利益profit added18.废品比例rejection percentage19.废品率standard rejection rate20.报废时价值,剩余价值,剩余价值residual value/scrap value21.机器运转费;机器运营本钱running cost of machine22.卖价selling expense23.销售间接费selling overhead24.寿命service life25.(合金)掺合比例standard alloying ratio26.标准价格standard price27.试铸时间time of trial shot28.总价格total cost29.试铸费trial casting cost30.除浇口费trimming cost31.生产yield32.生产率yield rate33.后加工合格率yield rate of finishing34.熔炼生产率yield rate of melting35.压铸成品率overall yield of castingⅩ压铸质量和缺陷casting quality and defect1.废品reject2.化学成分不合格chemical consistenceabnormal3.飞边joint flash4.毛刺veining;burr5.气孔blowhole6.气泡blister7.气泡bubble8.激冷区chill zone9.冷脆性cold shortness10.冷隔cold shut;cold filling11.裂纹crack12.铸点dot13.花纹flower msrk;stripping for shot blast14.外部材料foreign material。
铸造英语专业词汇
GB5611-851. 基本术语1.1. 铸造foundry, founding, casting1.2. 铸造工艺foundry technology1.3. 铸件casting1.4. 砂型铸造sand casting process1.5. 特种铸造special casting process2. 合金性能2.1. 流动性fluidity2.2. 充型能力mold-filling capacity2.3. 吸气gas absorption2.4. 过冷undercooling, supercooling2.5. 过冷度degree of undercooling2.6. 成核nucleation2.7. 自发成核（均质成核）homogeneous nucleation2.8. 非自发成核（非均质成核）heterogeneous nucleation2.9. 凝固温度范围solidifica tion range2.10. 定向凝固（顺序凝固）directional solidification2.11. 液态收缩（液体收缩）liquid contraction2.12. 凝固收缩solidification contraction2.13. 固态收缩（固体收缩）solid contraction 2.14. 凝固时间solidification time2.15. 自由收缩free contraction2.16. 受阻收缩hindered contraction2.17. 铸件线收缩率shrinkage2.18. 收缩应力contraction stress2.19. 热应力thermal stress2.20. 相变应力transformation stress, phase change stress2.21. 铸造应力casting stress2.22. 残留应力（残余应力）residual stress3. 铸造用材料3.1. 金属原材料3.1.1. 金属原材料metallic raw material3.1.2. 生铁pig iron3.1.3. 铁合金ferro-alloy3.1.4. 回炉料foundry returns3.1.5. 中间合金master alloy3.2. 燃料3.2.1. 铸造焦炭foundry coke 3.2.2. 冶金焦炭metallurgical coke3.2.3. 固定碳fixed carbon3.3. 熔剂3.3.1. 熔剂flux3.3.2. 除气熔剂（除气剂）degassing flux 3.3.3. 覆盖熔剂（覆盖剂）covering flux 3.3.4. 精炼熔剂（精炼剂）refining flux 3.3.5. 耐火材料3.3.6. 耐火度（耐火性）refractoriness 3.3.7. 耐火砖firebrick3.3.8. 耐火粘土fireclay3.3.9. 硅砖silica brick3.3.10. 镁砂grain magnesite3.4. 造型材料3.4.1. 造型材料molding material3.4.2. 砂sand3.4.3. 水洗砂washed-out sand3.4.4. 硅砂silica sand3.4.5. 天然砂natural sand3.4.6. 人工砂artificial sand3.4.7. 天然粘土砂naturally clay-bonded sand3.4.8. 橄榄石砂olivine sand3.4.9. 铬铁矿砂chromite sand3.4.10. 锆砂zircon sand3.4.11. 炭粒砂carbon sand3.4.12. 精硅砂sharp sand3.4.13. 红砂red sand3.4.14. 熟料砂chamotte sand3.4.15. 粘结剂binder3.4.16. 粘土clay3.4.17. 无机粘结剂inorganic binder3.4.18. 有机粘结剂organic binder3.4.19. 高岭土kaolin3.4.20. 膨润土bentonite3.4.21. 钠基膨润土sodium bentonite3.4.22. 钙基膨润土calcium bentonite3.4.23. 活化膨润土activated bentonite 3.4.24. 干性油drying oil3.4.25. 自硬粘结剂(冷硬粘结剂) no bakebinder3.4.26. 热固树脂粘结剂thermosetting resin binder3.4.27. 油类粘结剂oil based binder3.4.28. 水玻璃粘结剂water glass binder, sodium silicate binder3.4.29. 纸浆废液lignin liquor3.4.30. 合脂粘结剂synthetic fat binder 3.4.31. 水玻璃模数sodium silicate modulus3.5. 辅助材料3.5.1. 附加物additives3.5.2. 发热剂exothermic mixture3.5.3. 分型剂（脱模剂）parting agent, stripping agent3.5.4. 固化剂（硬化剂）hardener3.5.5. 悬浮剂suspending agent3.5.6. 涂料coating3.5.7. 砂处理3.5.8. 型砂制备（砂处理）sand preparation3.5.9. 混砂sand mulling, sand mixing 3.5.10. 型砂（造型混合料）molding sand 3.5.11. 芯砂（造芯混合料）core sand 3.5.12. 合成砂synthetic sand3.5.13. 自硬砂self-hardening sand3.5.14. 水玻璃砂sodium silicate-bonded sand3.5.15. 覆膜砂precoated sand3.5.16. 烂砂泥（麻泥）loam3.5.17. 调匀砂temper sand3.5.18. 面砂facing sand3.5.19. 背砂（填充砂）backing sand3.5.20. 单一砂unit sand3.5.21. 含泥量clay content3.5.22. 含水量moisture content 3.5.23. 旧砂floor sand3.5.24. 枯砂（焦砂）burnt sand3.5.25. 废砂waste sand3.5.26. 热砂hot sand3.5.27. 松砂aeration , sand-cutting3.5.28. 筛分（筛析）screen analysis3.5.29. 旧砂处理sand reconditioning3.5.30. 旧砂再生sand reclamation3.5.31. 沉降分选elutria tion, decantation 3.5.32. 型砂性能及试验3.5.33. 型砂试验sand testing3.5.34. 透气性permeability3.5.35. 流动性flowability3.5.36. 型砂强度sand strength3.5.37. 湿强度green strength3.5.38. 干强度dry strength3.5.39. 耐用性（复用性）durability3.5.40. 砂型（芯）硬度mold hardness 3.5.41. 热变形hot deformation3.5.42. 残留强度retained strength3.5.43. 热强度hot strength3.5.44. 韧性toughness3.5.45. 发气率（发气速度）gas evolution rate3.5.46. 发气性（发气量）gas evolution 3.5.47. 吸湿性moisture absorption3.5.48. 落砂性knock-out capability3.5.49. 潰散性collapsibility3.5.50. 胶质价colloid index3.5.51. 破碎指数shatter index3.5.52. 砂处理设备3.5.53. 热气流烘砂装置hot pneumatic tube drier3.5.54. 混砂机sand muller, sand mixer 3.5.55. 松砂机aerator, sand cutter3.5.56. 冷却提升机cooling elevator, coolevator3.5.57. 筛砂机riddle3.5.58. 磁力滚筒magnetic separator 3.5.59. 旧砂再生设备sand reclamation3.5.60. 气力输送装置pneumatic tube conveyor4. 铸造合金4.1. 铸铁4.1.1. 铸铁cast iron4.1.2. 铸铁石墨形态morphology of graphite in cast iron4.1.3. 灰铸铁（灰口铸铁）gray cast iron 4.1.4. 白口铸铁white cast iron4.1.5. 麻口铸铁mottled cast iron4.1.6. 共晶度degree of saturation4.1.7. 碳当量carbon equivalent4.1.8. 片状石墨flake graphite4.1.9. 初生石墨primary graphite4.1.10. 孕育铸铁inocula ted cast iron4.1.11. 球墨铸铁spheroidal graphite cast iron, nodular graphite iron,ductile iron4.1.12. 球状石墨spheroidal graphite, nodular graphite4.1.13. 可锻铸铁malleable cast iron4.1.14. 黑心可锻铸铁black heart malleable cast iron4.1.15. 珠光体可锻铸铁pearlitic malleable cast iron4.1.16. 铁素体可锻铸铁ferritic malleable cast iron4.1.17. 白心可锻铸铁white heart malleable cast iron4.1.18. 团絮石墨tempered graphite4.1.19. 冷硬铸铁（激冷铸铁）chilled iron 4.1.20. 耐磨铸铁wear resisting cast iron 4.1.21. 耐热铸铁heat resisting cast iron 4.1.22. 耐酸铸铁acid resisting cast iron4.1.23. 高硅铸铁high silicon cast iron4.1.24. 蠕墨铸铁vermicular cast iron, compacted graphite cast iron4.1.25. 蠕虫状石墨vermicular graphite 4.1.26. 合金铸铁alloy cast iron4.2. 铸钢4.2.1. 铸钢cast steel4.2.2. 炭素铸钢carbon cast iron4.2.3. 低合金铸钢low alloy cast steel4.2.4. 高锰钢high manganese steel 4.2.5. 铁素体钢ferritic steel4.2.6. 铸造非铁合金4.2.7. 青铜bronze4.2.8. 铅青铜lead bronze4.2.9. 铝青铜aluminum bronze4.2.10. 黄铜brass4.2.11. 铝铜合金aluminum-copper alloy 4.2.12. 铝镁合金aluminum-magnesium alloy4.2.13. 铝硅合金aluminum-silicon alloy4.2.14. 镁合金magnesium alloy4.2.15. 轴承合金（减摩合金）bearing metal, antifrictional metal4.2.16. 巴氏合金babbitt alloy4.2.17. 钛合金titanium alloy5. 熔炼工艺及设备5.1. 熔炼基本术语5.1.1. 熔化（熔炼）melting5.1.2. 重熔remelting5.1.3. 炉料charge5.1.4. 熔化率melting rate5.1.5. 炉料计算charge calculation5.1.6. 双联熔炼duplexing5.1.7. 元素烧损（元素烧损率）melting losses of various chemicalelements5.1.8. 熔炼损耗（烧损）total melting loss 5.1.9. 还原气氛reducing atmosphere5.1.10. 氧化气氛oxidizing atmosphere5.1.11. 惰性气体inert gas5.1.12. 碱度（碱性指数）index of basicity 5.1.13. 碱性渣basic slag5.1.14. 酸性渣acid slag5.1.15. 精炼refining5.1.16. 遗传性heredity5.1.17. 铸铁熔炼5.1.18. 风口比tuyere ratio5.1.19. 有效高度effective height5.1.20. 送风强度blast intensity5.1.21. 预热送风hot blast5.1.22. 底焦coke bed5.1.23. 层焦coke split5.1.24. 隔焦（结力焦）buffer coke charge 5.1.25. 炉衬furnace lining5.1.26. 碱性炉衬basic lining5.1.27. 酸性炉衬acid lining5.1.28. 棚料bridging5.1.29. 熔池bath5.1.30. 吸碳carbon pick-up5.1.31. 铁焦比（焦比）iron-coke ratio 5.1.32. 出渣deslagging5.1.33. 打炉cupola drop5.2. 铸钢5.2.1. 氧化熔炼法oxidizing melting5.2.2. 不氧化熔炼法dead melting5.2.3. 真空熔炼vacuum refining5.2.4. 电渣熔炼electro-slag melting 5.2.5. 熔渣slag5.2.6. 沉渣sludge5.2.7. 浮渣dross, cinder5.2.8. 氧化期（沸腾期）oxidizing stage, boil5.2.9. 还原期deoxidizing stage, blocking stage5.2.10. 还原渣reducing slag5.2.11. 氧化渣oxidizing slag5.2.12. 白渣white slag5.2.13. 脱氧deoxidation5.2.14. 扒渣slagging- off5.2.15. 脱碳decarburization5.2.16. 脱硫desulphurization5.2.17. 脱磷dephosphorization5.2.18. 增碳recarburizing5.2.19. 脱氧剂deoxidizer5.2.20. 非铁金属熔炼5.2.21. 挥发损耗volatilizing losses5.2.22. 静置stewing, holding5.2.23. 吹氮nitrogen flushing5.3. 熔炼设备5.3.1. 冲天炉cupola5.3.2. 水冷冲天炉water-cooled cupola 5.3.3. 热风冲天炉hot-blast cupola5.3.4. 湿法除尘器we t cap5.3.5. 炉缸cupola well5.3.6. 前炉forehearth 5.3.7. 冲天炉加料机cupola charging machine5.3.8. 爬式加料机skip hoist5.3.9. 电磁配铁称electro-magnetic weighing balancer5.3.10. 电磁盘electromagnetic chuck5.3.11. 电弧炉（直接电弧炉）arc furnace, direct arc furnace5.3.12. 感应电炉electric induction furnace 5.3.13. 电渣炉electroslag furnace5.3.14. 电磁搅拌electromagnetic agitation 5.3.15. 浇包ladle5.3.16. 摇包shaking ladle5.3.17. 底注包bottom pouring ladle5.3.18. 保温炉holding furnace5.3.19. 坩埚炉crucible furnace5.3.20. 熔融金属处理5.3.21. 孕育inoculation5.3.22. 多孔塞法porous plug process5.3.23. 变质modification5.3.24. 墨化剂graphitizer5.3.25. 过热superheating5.3.26. 石墨球化处理nodularizing treatment of graphite5.3.27. 碳当量仪eutectometer5.3.28. 三角试块wedge test-piece5.3.29. 真空除气vacuum degassing5.4. 浇注5.4.1. 浇注pouring5.4.2. 保护气氛浇注pouring under controlled atmosphere5.4.3. 浇注速度pouring rate5.4.4. 浇注温度pouring temperature5.4.5. 浇注时间pouring time5.4.6. 浇注位置pouring position5.4.7. 型内孕育inmold inocula tion5.4.8. 压铁weight5.4.9. 捣冒口churning, pumping5.4.10. 点冒口（补注）teeming5.4.11. 浸入式高温计immersion pyremeter 5.4.12. 补炉patching5.4.13. 炉龄（炉衬寿命）campaign6. 工艺设计及工艺装备6.1. 工艺设计6.1.1. 铸造工艺设计mold design6.1.2. 铸造工艺装备设计foundry tools design6.1.3. 铸造工艺图foundry moldingdrawing6.1.4. 铸件图（毛坯图）drawing of rough casting6.1.5. 起模斜度（拔模斜度）pattern draft 6.1.6. 收缩余量shrinkage allowance6.1.7. 工艺补正量molding allowance6.1.8. 加工余量machining allowance6.1.9. 吃砂量mold thickness6.1.10. 补贴pad6.1.11. 分型负数joint allowance6.1.12. 铸件尺寸公差dimensional tolerance of casting6.1.13. 铸件重量公差weight allowance of casting6.1.14. 铸件加工基准面reference face for machining of casting6.1.15. 铸件表面粗糙度surface roughness of casting6.2. 浇冒口系统6.2.1. 浇注系统（浇口）gating system, running system6.2.2. 封闭式浇注系统choked running system, pressurized gating system6.2.3. 半封闭式浇注系统enlarged runner system6.2.4. 开放式浇注系统unchoked running system, non-pressurized gating system6.2.5. 浇口盆（外浇口）pouring basin6.2.6. 浇口杯pouring cup6.2.7. 浇口塞blanking-off plug6.2.8. 直浇道sprue6.2.9. 直浇道窝sprue base6.2.10. 横浇道runner6.2.11. 筛网芯（滤网芯）strainer core6.2.12. 内浇道ingate6.2.13. 离心集渣浇注系统whirl gate, dirt trap system6.2.14. 顶注式浇注系统top ga ting system6.2.15. 底注式浇注系统bottom gating system6.2.16. 阶梯式浇注系统step gating system 6.2.17. 雨淋浇口shower gate6.2.18. 缝隙浇口slot ga te6.2.19. 压边浇口lip runner, kiss runner6.2.20. 牛角式浇口horn gate6.2.21. 热节hot spot6.2.22. 冒口riser, feeder heed6.2.23. 冒口效率riser efficiency6.2.24. 明冒口open riser6.2.25. 暗冒口blind riser6.2.26. 侧冒口（边冒口）side riser6.2.27. 压力冒口pressure riser6.2.28. 大气压力冒口atmospheric riser6.2.29. 发气压力冒口（气弹冒口）gas-delivered pressure riser6.2.30. 透气砂芯pencil core6.2.31. 冒口颈riser neck6.2.32. 冒口根riser pad6.2.33. 保温冒口套heat insulating feeder sleeve6.2.34. 发热冒口套exothermic feeder sleeve 6.2.35. 补缩距离feeding distance, feeding zone6.2.36. 易割冒口knock-off head6.2.37. 易割片（易割芯片）washburn core 6.2.38. 模样6.2.39. 铸造工艺装备foundry tools and equipment6.2.40. 模样（铸模，模）pattern6.2.41. 母模master pattern6.2.42. 金属模metal pattern6.2.43. 骨架模skeleton pattern6.2.44. 石膏模plaster pattern6.2.45. 塑料模plastic pattern6.2.46. 整体模one-piece pattern6.2.47. 分开模parted pattern, split pattern 6.2.48. 活块loose piece6.2.49. 模板pattern plate6.2.50. 模底板pattern mounting pla te6.2.51. 单面模板single face pattern plate6.2.52. 双面模板match pla te6.2.53. 放样（伸图）hot dimensional drawing 6.2.54. 缩尺（模样工缩尺）shrinkage rule, pattern-maker’s r ule6.3. 芯盒6.3.1. 芯盒core box6.3.2. 脱落式芯盒troughed core box6.3.3. 下芯量具core setting scale6.3.4. 下芯夹具core jig6.3.5. 烘芯板core drying plate6.3.6. 砂箱6.3.7. 砂箱flask, molding box6.3.8. 箱带（箱挡）flask bar, cross bar6.3.9. 脱箱snap flask6.3.10. 套箱mold jacket6.3.11. 套销hollow pin, stub pin7. 造型及造芯7.1. 造型7.1.1. 造型molding7.1.2. 型腔mold cavity7.1.3. 铸型（型）mold7.1.4. 砂型sand mold7.1.5. 上型（上箱）cope, top part7.1.6. 下型（下箱）drag, bottom part7.1.7. 手工造型hand molding7.1.8. 机器造型machine molding7.1.9. 自动化造型automa tic molding7.1.10. 分型面mold joint7.1.11. 有箱造型flask molding7.1.12. 两箱造型two-part molding7.1.13. 三箱造型three-part molding7.1.14. 不平分型面stepped joint7.1.15. 无箱造型flaskless molding7.1.16. 脱箱造型removable flask molding 7.1.17. 地坑造型pit molding7.1.18. 刮板造型sweep molding7.1.19. 抛砂造型impeller ramming, sand slinging molding7.1.20. 组芯造型core assembly molding 7.1.21. 假箱造型oddside molding7.1.22. 微震压实造型vibratory squeezing molding7.1.23. 高压造型high pressure molding 7.1.24. 湿砂型（湿型，潮型）green sand mold7.1.25. 砂型烘干mold drying7.1.26. 干砂型（干型）dry sand mold7.1.27. 表面烘干型skin dried mold7.1.28. 烂砂泥型loam mold7.1.29. 砂床bed7.1.30. 过渡角transition angle7.1.31. 吊砂cod7.1.32. 砂钩lifter7.1.33. 负压造型（真空密封造型）vacuum molding7.1.34. 流态砂造型fluid sand molding7.1.35. 漏模pattern stripping7.1.36. 填砂mold-filling7.1.37. 紧实（紧砂，舂砂）ramming7.1.38. 震实jolt ramming7.1.39. 压实squeezing ramming7.1.40. 紧实度degree of ramming7.1.41. 二氧化碳法造型CO2 process7.1.42. 自硬砂造型self-hardening sand molding7.1.43. 塞砂tucking7.1.44. 刮砂strike-off7.1.45. 造型生产线molding line7.1.46. 刷水swabbing7.1.47. 敲模rapping7.1.48. 起模（拔模）stripping7.1.49. 扎出气孔venting7.1.50. 排气道venting channel7.1.51. 修型patching7.1.52. 冷铁densener, chill7.1.53. 外冷铁surface densener7.1.54. 内冷铁internal densener7.1.55. 验型（验箱）trial closing7.1.56. 合型（合箱，组型）mold assembling, closing7.2. 造芯7.2.1. 造芯（制芯）core making7.2.2. 芯（芯子）core7.2.3. 芯骨core rod, core scab7.2.4. 油砂芯oil sand core7.2.5. 预制芯embeded core, ram upcore7.2.6. 芯头core print7.2.7. 芯座core print7.2.8. 芯头斜度core print taper7.2.9. 芯头间隙core print clearance7.2.10. 壳芯shell core7.2.11. 烘芯core baking7.2.12. 通气蜡线vent wax7.2.13. 冷芯盒法cold box process7.2.14. 热芯盒法hot box process7.2.15. 芯撑chaplet7.2.16. 造型工具7.2.17. 造型工具hand tools of molding7.2.18. 压勺heart and spoon7.2.19. 提沟cleaner7.2.20. 双头铜勺（秋叶）double ended radius sleeker7.2.21. 镘刀trowel7.2.22. 造型及造芯设备7.2.23. 造型机molding machine7.2.24. 压实造型机squeezing molding machine7.2.25. 震击台bumper7.2.26. 振动台vibrating table7.2.27. 微震压实造型机vibratory squeezer 7.2.28. 震实造型机jolt molding machine7.2.29. 高压造型机high pressure molding machine7.2.30. 射压造型机shooting andsqueezing molding machine7.2.31. 多触头造型机equalizing piston squeezer7.2.32. 抛砂机sand slinger7.2.33. 起模机drawing machine7.2.34. 射砂机core shooter7.2.35. 挤芯机core extruder 7.2.36. 铸型输送机mold conveyor8. 铸件落砂及清理8.1. 落砂及清理8.1.1. 落砂shake-out, knock-out8.1.2. 除芯decoring8.1.3. 噴砂清理sand blasting8.1.4. 抛丸清理shot blasting8.1.5. 水力清砂hydraulic cleaning8.1.6. 水砂清砂hydraulic blast8.1.7. 清理cleaning, fettling8.1.8. 清砂cleaning8.1.9. 火焰表面清理scarfing8.1.10. 清铲chipping8.1.11. 化学清砂chemical cleaning8.1.12. 精整dressing and finishing8.1.13. 落砂机knock-out machine8.1.14. 抛丸清理机shot blast machine 8.1.15. 清理滚筒tumbling barrel8.1.16. 抛丸落砂清理设备shot blast reclaiming equipment8.1.17. 悬挂式磨轮swing frame grinder 8.1.18. 修补及矫正8.1.19. 矫正coining, straightening8.1.20. 焊补repair welding8.1.21. 渗补impregnation8.1.22. 特种铸造8.1.23. 金属型铸造8.1.24. 金属型铸造permanent mold casting, gravity die casting8.1.25. 金属型metal mold8.1.26. 金属芯metal core8.1.27. 覆砂金属型sand-lined metal mold 8.1.28. 排气塞venting plug8.1.29. 排气槽air vent8.1.30. 龟裂heat checking8.1.31. 金属型铸造机gravity die casting machine9. 压力铸造9.1. 压力铸造（压铸）die casting, pressure die casting9.2. 压铸型die-casting die, die9.3. 动型moving die, ejector die half 9.4. 定型fixed die, cover die half9.5. 合型力clamping force , dielocking force9.6. 压室pressure chamber9.7. 鹅颈管gooseneck9.8. 分流器spreader, sprue spreader9.9. 顶杆ejector pin9.10. 溢流槽overflow well9.11. 压射冲头（压室）injection piston, plunger9.12. 压射比压injection pressure9.13. 压射速度injection speed9.14. 保压时间dwell time9.15. 真空压铸evacuated die casting, vacuum die casting9.16. 充氧压铸pore-free die casting9.17. 双冲头压铸（精速密压铸）acurad(accurate?) die casting9.18. 压铸机die casting machine9.19. 冷室压铸机cold chamber die casting machine9.20. 热室压铸机hot chamber die casting machine9.21. 镶铸法insert process9.22. 离心铸造9.23. 离心铸造true centrifugal casting9.24. 半离心铸造semi-centrifugal casting 9.25. 离心浇注centrifugal pressure casting, centrifuge casting9.26. 双金属离心铸造bimetal centrifugal casting9.27. 离心铸造机centrifugal casting machine10. 熔模铸造10.1. 失模铸造lost pattern casting10.2. 熔模铸造（失蜡铸造）fusible pattern molding, lost-wax molding10.3. 压制熔模fusible pattern injection 10.4. 压型pattern die10.5. 熔模fusible pattern10.6. 盐模salt pa ttern10.7. 蜡模wax-pattern10.8. 模组pattern assembly10.9. 熔模涂料（浆料）slurry10.10. 面层涂料investment precoat10.11. 撒砂stuccoing 1010.12. 脱蜡dewaxing10.13. 熔烧sintering10.14. 壳型铸造10.15. 壳型铸造shell molding10.16. 结壳时间investing time10.17. 结壳温度investing temperature 10.18. 硬化温度curing temperature 10.19. 硬化时间curing time10.20. 其它铸造方法10.21. 陶瓷型铸造ceramic molding10.22. 陶瓷型浆料ceramic slurry10.23. 灌浆paste pouring10.24. 喷烧torch firing10.25. 低压铸造low-pressure die casting 10.26. 充型压力mold filling pressure 10.27. 保压压力dwell pressure10.28. 升液管stalk10.29. 真空吸铸suction casting10.30. 差压铸造（反压铸造）counter-pressure casting10.31. 实型铸造full mold process, cavityless casting10.32. 泡沫塑料模styrofoam pattern 10.33. 磁型铸造（磁丸铸造）magnetic shot molding process10.34. 凝壳铸造slush casting10.35. 石膏型铸造plaster molding10.36. 连续铸造continuous casting11. 铸件质量及铸件缺陷11.1. 铸件质量基本术语11.1.1. 铸件检验inspection of casting 11.1.2. 铸件质量分析quality analysis of casting11.1.3. 铸件外观质量visual quality of casting11.1.4. 铸件内在质量internal quality of casting11.1.5. 铸件使用性能service ability of casting11.1.6. 单铸试块separated test bar of casting11.1.7. 附铸试块test lug11.1.8. 缺陷铸件defective casting11.1.9. 废品reject11.1.10. 无损检验（无损探伤）nondestructive inspection11.1.11. 破坏性试验destructive testing 11.1.12. 多肉类缺陷11.1.13. 飞翅（飞边）joint flash11.1.14. 毛刺veining11.1.15. 抬型（抬箱）cope raise , raised mold11.1.16. 胀箱swell11.1.17. 冲砂erosion, cut, wash11.1.18. 掉砂drop, crush11.1.19. 外渗物（外渗豆）sweat11.2. 孔洞类缺陷11.2.1. 气孔blow hole11.2.2. 针孔pinhole11.2.3. 缩孔shrinkage11.2.4. 缩松dispersed shrinkage11.2.5. 疏松（显微缩松）porosity microshrinkage11.2.6. 裂纹、冷隔类缺陷11.2.7. 冷裂cold cracking11.2.8. 热裂hot tearing11.2.9. 热处理裂纹heat treatment crack 11.2.10. 白点（发裂）flake11.2.11. 冷隔cold shut, cold lap11.2.12. 浇注断流interrupted pour11.2.13. 表面缺陷11.2.14. 鼠尾rat-tail11.2.15. 沟漕buckle11.2.16. 夹砂结疤（夹砂）scab11.2.17. 机械粘砂（渗透粘砂）metal penetration11.2.18. 化学粘砂（烧结粘砂）burn-on 11.2.19. 表面粗糙rough surface11.2.20. 皱皮elephant skin11.2.21. 缩陷depression11.2.22. 残缺类缺陷11.2.23. 浇不到misrun11.2.24. 未浇满poured short11.2.25. 跑火run-out, bleeding11.2.26. 型漏（漏箱）run-out, bleeding 11.2.27. 损伤（机械损伤）damage11.2.28. 形状及重量差错类缺陷11.2.29. 拉长exaggeration of dimension 11.2.30. 超重over-weight11.2.31. 变形distortion, warping11.2.32. 错型（错箱）shift11.2.33. 错芯core shift11.2.34. 偏芯（漂芯）core raised, corelift 11.3. 夹杂类缺陷11.3.1. 夹杂物inclusion11.3.2. 冷豆cold shot11.3.3. 内渗物（内渗豆）internal sweat 11.3.4. 渣气孔scum, slag-blow hole11.3.5. 砂眼sand inclusion11.3.6. 性能、成分、组织不合格11.3.7. 亮皮pearlite layer11.3.8. 菜花头cauli-flowering11.3.9. 石墨飘浮carbon floatation11.3.10. 石墨集结kish graphite spot11.3.11. 组织粗大open grain structure11.3.12. 偏析segregation11.3.13. 硬点hard spot11.3.14. 反白口inverse chill11.3.15. 球化不良under-nodularizing11.3.16. 球化衰退degradated spheroidisation 11.3.17. 脱碳decarburization。
铸造专业相关英语词汇
Lesson 11. fundamental a. 基础的，基本的2. foundry n. 铸造，铸造工厂（车间）3. process n. 工序、过程vt. 使经历某一过程4. molding（美）n. 造型moulding（英）n. 造型5. casting n. 铸造（法）、浇注、铸件6. involve vt. 包含involved in 包含在……中，在……中涉及7. suitable a. 合适的，适当的8. mold（美）n. 铸型，型mould（英）n. 铸型，型9. govern vt.vi. 支配，决定（be）governed by 取决于……；由……决定以……为转移。
10. green sand mold n. 湿（砂）型11. natural a. 天然的，本来的12. pour vi. Vt. 浇注13. dry sand mold n. 干（砂）型14. mixture n. 混合物，混合料15. ram vi. Vt. 冲紧，紧实16. bake vt. Vi. 烘烤，焙烤17. moisture n. 水分，潮气，湿度18. firm a. 坚硬的19. coremaking n. 制芯20. cavity n. 空腔，空洞，孔21. project vt. Vi. 伸出，突出22. silica n. 二氧化硅，石英23. binding material n. 粘结材料，粘结剂24. independently ad. 独立地，单独地25. melt vi. Vt. n. 熔化，熔炼，溶液26. lead n. 铅27. tin n. 锡28. zinc n. 锌29. pot n. 坩埚，罐30. burner n. 燃烧器，燃烧炉31. aluminium n. 铝32. brass n. 黄铜，铜锌合金33. bronze n. 黄铜，铜锡合金34. crucible furnace n. 坩埚炉35. cast iron n. 铸铁36. cupola n. 冲天炉37. electric arc furnace n. 电弧炉38. open hearth furnace n. 平炉39. converter n. 转炉40. term vt. 把……称为，n. （专门）名词41. container n. 容器42. ladle n. 浇包43. cleaning n. 清理，清砂44. finishing n. 打磨45. solidify vt. Vi. 使凝固46. in the form of 以……形式47. gate n. 浇口，内浇口48. riser n.冒口49. adhere vi. 粘附，粘着50. department n. 工段，车间，部门51. inspect vi. Vt. 检查，检验，部门52. heat treatment n. 热处理53. ship vt. Vi. 发运，船运，n. 船54. consumer n. 用户Lesson 21. essentially ad. 本质上，实质上，基本上2. pack vt. 舂、紧，充填3. withdraw （withdrew，withdrawn）vt. 起出，取出4. layer n. 层5. riddle n.；vt. 筛，过筛6. screen n.；vt. 筛子，筛分7. ensure vt. 保证8. unifomity n. 均匀性9. uniformly ad. 均匀地10. facing sand n. 面砂11. heat-resistant a. 耐热的12. results in 导致13. collapse vi. 倒塌，毁坏14. excessive a. 过度的15. escape vi. 逸出16. cause vt.；n. 使产生，引起17. blow-hole n. 气孔18. cope n. 上型（箱）19. drag n. 下型（箱）20. boxlike a. 箱形的21. frame n. 框子22. flask n. 砂箱23. intermediate a.；n. 中间的，中间物24. cheek n. 中型（箱）25. joint n.；vt. 连接面，接合面26. vent vt. 通气27. venthole n. 通气孔28. properly ad. 适当地，正确地29. permeability n. 透气性30. interior a. 内部的，里面的31. hard-baked a. 烘干，硬化32. insert vt. 放入 n. （pl.）金属型芯，内冷铁33. undercut n. （铸件上的）凹陷部分34. hollow n. 空穴，孔35. entire a. 全部的，完整的36. assembly n. 总装，组合件37. molten a. 熔融的38. downward ad. a. 向下39. runner n. 横浇道40. compensate vt. 补偿41. shrinkage n. 收缩，收缩量42. remove vt. 去掉，消除43. lug n. （箱）耳44. pin n. （合箱）销45. typical a. 典型的46. mold cavity n. 型腔47. parting surface n. 分型面48. pouring basin n. 浇口盆49. gate sprue n. 直浇道50. bottom board n. 底板51. cross-sectional view n. 剖面图Lesson 31. foundryman n. 铸造工人，铸造工作者2. non-ferrous a. 非铁（金属）的，有色（金属）的3. light-alloy a. 轻合金4. estimate n.；vt. 评价，判断5. fineness n. 细度，光洁度6. plasticity n. 可塑性7. bond n.；vt. 粘结，粘结力，粘结剂8. refractoriness n. 耐火性9. durability n. 耐久（用）性10. in different degrees 在不同程度上11. constituent n.；a. 成分，组成物12. grain n. 颗粒13. aluminium silicate n. 硅酸铝14. clay n. 粘土15. binder n. 粘结剂16. artificial a. 人工的，人造的17. greensand n. 湿砂18. impression n. 型腔，痕迹19. strickle n. 刮板20. demand vt.；n. 要求，需要21. proportioning n. 使成比例，配料，（按比例）配合22. hold together 结合23. fuse v. 熔化24. skin n. 表皮，外壳25. relate to 与……有关26. withstand （withstood）vt. 经得起，耐得住27. synthetic a.；n. 合成的，合成剂28. dig （dug，dug）vt. 挖掘，采掘29. pit n. 矿井，矿坑30. mix v. 混合31. relatively ad. 按比例的，相对地32. select vt. 选用，挑选33. nonthermosetting hydrocarbon resin 非热固性碳氢树脂34. bentonite n. 膨润土35. result from 由…引起，由于36. keep from 防止Lesson 41. patternmaking n.模样制造2. pattern n. 模样3. patternmaker n. 木模工4. affect vt. 影响，对…起作用5. designing n., a. 设计（的）6. drafting n. 制图7. machining n. 机械加工8. be common to 为…所共有9. talk over 商量，讨论10. planning n. 设计，计划11. blueprint n. 蓝图，设计图12. visualize vt. 想象出，设想出13. preliminary a. 初步的14. cost n. 成本，费用15. order vt. 订货16. distortion n. 变形，挠曲17. location n. 位置18. allowance n. 余量19. parting line n. 分型线20. establish vt. 建立21. layout n. 放样图，设计图22. procedure n. 方法，（生产）过程23. decide upon = decide on 决定，选定，确定24. reproduction n. 复制品25. dress （dressed，drest）vt. 刨光，打磨26. edge n. 边，棱边，侧面27. square a. 方的；n. 角尺28. shrink rule n. 缩尺29. divider n. （pl.）两脚规，分规30. instrument n. 工具，装置31. pointed knife n. 尖刀32. tool n. 工具，刀具，机床33. accuracy n. 精度，准确度34. pattern allowance n. 模样余量，模样放尺35. take into account 考虑，重视36. drawing n. 图样37. check vt.；n. 校队，核对，开裂Lesson 51. subject （与to连用）易受，经受，常有2. wear n.；vt. 磨损3. rapping n. 松模4. subsequent a. 继起的，后来的5. abrasive a.；n. 磨损的，摩擦的6. impervious a. 不能透过的，不渗水的7. alternately adv. 交替的8. damp a.；n. 潮湿的9. tear n. 撕裂，扯破10. plastic n. （常用pl.）塑料，合成树脂11. gypsum n. 石膏12. plaster n. 熟石膏13. exact a. 精确的，精密的14. undersize n. 尺寸过小，尺寸不足15. draft n. （起模）斜度16. machining provision n. 机械加工余量17. solid shrinkage n. 固态收缩18. freezing temperature n. 凝固温度19. contraction n. 收缩20. allow for 考虑到21. automatically ad. 自动地22. approximate a. 近似的，大约的23. malleable iron n. 可锻铸铁，马铁24. magnesium n. 镁25. master pattern n. 母模26. draw （drew，drawn）vt. 起出（模样）27. vertical a. 垂直的28. taper vt.；n. 退拔，(起模)斜度29. inward a. 向内的30. mount vt. 固定，装配31. accuracy of finish n. 加工精度Lesson 61. skin-dried mold n. 表面干燥型2. air-dried mold n. 空气干燥铸型3. loam mold n. 泥型4. cement-boned mold n. 水泥砂型5. dry-sand core mold n. 组芯铸型6. investment mold n. 熔模铸型7. maintain vt. 维持，保持，维护8. characteristic n. ；a. 特性，性能9. desirable a. ；n. 所希望的，合乎要求的10. softness n. 柔软（性，度）11. offer vt.；n. 提供，给予，产生12. resistance n. 阻力，抗（耐）……性13. crack n. ；vi. 开裂，裂纹14. favor=favour vt. ; n. 欢迎，赞成15. close vt. ; a. ; n. 合箱，关闭16. shake out n. （振动）落砂17. continuous cycle n. 连续循环，连续周期18. duration n. 持续时间19. majority n. 多数20. miscellaneous a. ；n. 各种的21. assemble vt. ；n. 装配，组合22. protection n. 保护，防护23. erosion n. 侵（腐）蚀，冲蚀24. corn flour n. 谷粉，玉米粉25. glutin n. 明胶26. molasses n. （废）糖浆27. linseed oil n. 亚麻油28. spray n. ；vt. 喷涂（料）29. gas torch n. 煤气喷灯30. portable a. 手提的，可携的，轻便的31. stove n. 炉子，烘炉32. infrared a. 红外线（的）33. backing sand 背砂，填充砂34. penetrate vt. 渗入Lesson 71. evolve vt. 放出，析出2. overnight ad. ；a. 在前一天晚上，隔夜3. oven n. 烘炉，加热室4. burner n. 燃烧器，喷灯5. charcoal n. 木炭6. circulate v. 循环，流通7. provide v. 供给，供应8. resist vt. 抵抗，耐，承受9. detail n. 细节，部分10. disadvantageous a. 不利的，有害的11. unusual a. 不平常的，独特的12. pattern plate n. 模板13. harden vt. 硬化14. sodium silicate n. 硅酸钠，水玻璃15. clay-free n. 无粘土的16. siliceous a. 含硅的，硅酸的17. carbon dioxide n. 二氧化碳18. promote vt. 促进，加速19. interfere vi. 妨碍，影响20. disintegration n. 溃散21. organic a. 有机的22. wood flour n. 木屑，木粉23. sand mixture n. 型砂24. delay vt. ；n. 耽误，延缓25. inadequate a. 不适宜的，不充分的26. portland cement n. 波特兰水泥（普通水泥）Lesson 81. gating system n. 浇注系统2. refer vt. 把…归类于，指（的是）3. passageway n. 通道4. pouring basin n. 浇口杯，浇口池5. strainer core n. 筛网芯片，撇渣芯，浇口滤片6. fulfill =fulfil vt. 实现，完成，达到7. be defined as ……的定义是，可称为8. be classified as 分成（为）……类9. parting-line gating n. 分型线浇注系统10. bottom gating n. 底注式浇注系统11. erosion n. 冲蚀，侵蚀12. turbulence n. 涡流，漩涡，紊流13. refractory tile pipe n. 耐火材料管14. horn gate n. 羊角浇口15. reversed horn gate n. 倒置羊角浇口16. top gating n. 顶注式浇注系统17. gradient n. 梯度18. directional solidification n. 定向凝固19. server as （for）起…作用，作为20. pencil gate n. 雨林浇口21. wedge gate n. 契形浇口22. choke n. 阻流口，节流口23. side gating n. 侧注式浇注系统24. slot n. 狭缝，隙缝25. step gate n. 阶梯浇口26. deliver vt. 供给，移交，交付27. function vi. ；n. 起作用，作用Lesson 91. satisfactory a. 满意的，（良）好的2. originally ad. 原来，最初3. hardness n. 硬度4. transport vt；n. 运输，输送5. （be）capable of –ing 能…，可以…，容许…6. smoothness n. 光滑度，平滑度7. wash n. 涂料8. coating n. 涂料，涂层9. impart vt. 给予，赋予10. collapsibility n.溃散性11. overstress vt.；n. 使…受（应）力过大，过应力，超载12. knock out 落砂，敲出，分离13. core print 型芯头（座）14. sharp sand n. 角形砂，纯砂15. pine-tree resin n. 松香16. cereal binder n. 谷类粘结剂17. dextrine = dextrin n. 糊精（C6H10O5）18. starch n. 淀粉Lesson 101. gray iron = (grey iron) 灰铸铁2. alloy n. 合金、齐v. 合铸，熔合，熔成合成3. carbon n. 碳4. silicon n. 硅5. manganese n. 锰6. sulfur = （sulphur） n. 硫7. phosphorus n. 磷8. intentionally ad. 有意地，故意地9. blast n. v. 鼓风，（一股）气流10. blast furnace 高炉，鼓风炉11. nickle n. 镍12. chromium n. 铬13. molybdenum n. 钼14. graphite n. 石墨15. property n. 特性，性能16. mechanical property 机械性能17. metallurgical a. 冶金的，金相的18. distribution n. 分布，分布状态19. microscope n. 显微镜20. specimen n. 试样，样品，标本21. grind v. 磨光，磨快（过去式ground）22. polish v. 抛光，打光，发亮23. etch v. 侵蚀，腐蚀24. matrix n. 基体25. whatsoever = whatever a. 无论什么，不管什么26. extend v. 延长，延伸，扩张27. ferrite n. 铁素体28. cementite n. 渗碳体29. pearlite n. 珠光体30. austenite n. 奥氏体31. steadite n. 斯氏体磷化物共晶体32. solution n. 溶解，溶液，熔体，解决（办法）33. solid solution 固溶体Lesson 111. white cast iron 白口铸铁2. malleable a. 有延展性的，可锻的3. malleable cast iron 球墨铸铁4. nodular a. 球粒状的5. nodular cast iron 球墨铸铁6. reminder n. 剩余物，剩下物7. chill n. a. v. 激冷，冷铁，冷铸，白口层8. rim n. 轮缘9. machining quality a. 机加工性能，被切削性10. forging n. 锻造，锻件11. ductility n. 韧性，延性12. separate v. 分离，析出13. temper v. n. 回火，搀和，加水混砂14. temper carton 退火碳15. interrupt v. 中断，阻碍16. implement n. 机具，农具17. agricultural implement 农具18. fitting n. a. 装配，配件，连接件19. pipe fitting 管接头，管配件20. instead of 代替，而不是21. in this respect 在这一点上，在这方面Lesson 121. primarily2. corrosion n. 腐蚀，侵蚀3. atmospheric a. 大气的，常压的4. exposure n. 暴露，照射5. plating n. 镀层，电镀，喷镀6. heat-treatable a. 可热处理的7. definite a. 确定的，一定的8. special a. 特别的，专门的9. （be）prone to 易于，倾向于10. reaction a. 反应，反作用11. （be）liable to 易于…，有…倾向12. oxidation n. 氧化13. whilst =（while） conj. 当…时，而14. flux n. 熔剂，焊剂15. cover flux 覆盖剂16. cleanse vt. 去掉，清除17. oxide n. 氧化物18. to the extent of 到…程度19. aging = （ageing） n. 老化，时效20. self-aging 自然时效21. strain n. 应变，变形22. stability n. 稳定性23. titanium n. 钛24. in varying proportions 按不同的比例25. nonmagnetic a. 无磁的，非磁性的26. nonsparking a. 不产生火花的27. possess vt. 具有，拥有，占有28. aircraft n. 航空器，飞机29. airborne a. 空运的，机载的，气载的30. equipment n. 设备，装备31. comparable with 可与…相比的，与…相类似的Lesson 131. recommend vt. 推荐2. specify vt. 规定3. molybdenum n. 钼4. nickel n. 镍5. tungsten n. 钨6. vanadium n. 钒7. zirconium n. 锆8. impact resistance n. 抗冲击性9. wear resistance n. 耐磨性，磨损阻力10. acid resistance n. 耐酸性11. weldability n. 可焊性，焊接性12. rigidity n. 刚性，刚度13. deflection n. 挠曲，弯曲，挠度14. separately ad. 单独地15. identify vt. 识别，鉴定，验明16. yield strength n. 屈服强度17. ductility n. 韧性，可锻性，延性18. effectiveness n. 有效性19. with regard to 就…而论，对于，关于20. deoxidizer = deoxidiser n. 脱氧剂，还原剂21. soundness n. 完好的程度22. adversely ad. 相反地23. objectionable a. 有害的，不好的24. tolerate vt. 允许，承受25. calcium n. 钙Lesson 141. cylinder n. 圆柱体，汽缸2. shell n. 壳体，贝壳3. casing n. 箱，盒，壳，套4. lining n. 衬，衬里，内衬5. brick n. 砖vt. 砌砖6. windbox 风箱，风带7. encircle vt. 环绕，绕……行一周8. tuyere n. 风口9. support vt. 支撑，支承10. leg n. 腿，脚，支柱11. hunge v. 铰接，用铰链结合；n. 铰链12. semicircular a. 半圆形的13. prop n. 撑杆，炉底撑杆14. remain vi. 剩下，余留15. coke n. 焦炭16. slag n. 炉渣，熔渣17. blower n. 鼓风机，风扇18. taphole 出铁孔19. spout n. 出铁槽，流槽，水落管20. float vi. 漂浮21. sighthole 观察孔22. charging door 加料门23. occupy vt. 占有，占据24. combustion n. 燃烧25. theoretical a. 理论上的26. boundary n. 边界，分界，界27. oxygen n. 氧28. eliminate vt. 除去，消除29. quantity n. 数量30. reduce v. 使还元，减少31. protective a 保护性的，保护的32. coke bed 底焦33. oxidize v. 使氧化34. influence n. 影响vt. 影响，对…有作用35. regulate vt. 调整，调节36. efficiency n. 效率37. collect v. 收集，聚集38. preheat v. 预热39. stack n. 烟囱，炉身，堆40. represent v. 代表，意味，象征41. waste n. v. 废物，浪费，纱头，回丝a. 无用的，废弃的Lesson 151. mass n. 物质，质量a.大量的，集中的2. mass-production 大量（大批，成批）生产3. previous ad. 以前，预先4. backbreaking a. 累人的5. item n. 条，项，项目6. outstanding a. 显著的，突出的7. advantage n. 优点，有利条件8. dimensionally ad. 在尺寸方面9. machine n. 机器 v. 加工，机械加工10. jig n. 钻模11. fixture n. 夹具12. dimension n. 尺寸，尺度13. coordinate v. 配合，使同等14. coordinating n. 配套设备15. stationary a. 不动的，静止的16. permanent a. 永久的，恒定不变的17. foundation n. 基础，地基18. jolt v. ；n. 震击19. squeeze v. ；n. 压实20. piston n. 活塞21. combination n. 结合，组合22. tendency n. 倾向，趋势23. correct vt. 纠正，改正24. compress vt. 压缩25. compressed air 压缩空气26. source n. 源，源泉27. valve n. 阀28. knee valve n. 膝阀29. exhaust n. ；v. 排出30. port n. 口，港口31. cycle n. 循环，周期32. swing v. 回转，摇摆，摆动33. force vt. 迫使，推动；n. 力，力量34. diameter n. 直径Lesson 161. sand slinger n. 抛砂机2. throw vt. ；n. 掷，抛3. impact n. ；vt. 冲击4. mechanism n. 机构，机理5. impeller n. 叶轮6. blade n. 叶片7. vane n. 叶片8. endless bucket elevator 环形斗式提升机9. track n.；v. 轨道，跟踪10. bay n. 柱距，跨（度）11. ride v.；n. 乘坐，驾驶12. centralized fingertrip control 中心按钮控制13. back and forth 前后，来回14. as compared with 与…比较15. aerate vt. 松砂16. provide with 装有，具备17. remote-contro station 遥控台18. visibility n. 能见度，视野，视界Lesson 171. gain ground 有进展2. in the order of 大约，按……次序3. enormous a. 巨大的4. fettling n. 清理，补炉5. none at all 一点也没有6. joint line 分型线7. feeder n. 冒口，补缩包8. dilation n. 扩大，膨胀9. bring about 引起、生产、导致10. ferrostatic head 铁水静压头11. dense a. 致密的12. uncommon a. 难得的、不平常的13. sophistication n. 采用先进技术14. associate vt. 联合be associated with 在…同时，与…有联系15. recover vt. 回收，复原16. expenditure n. 费用17. capital expenditure 基建费18. superior a. ；n. 优等的19. gradually ad. 逐渐20. short series 小批量21. jobbing n. 重复性很小的工作22. unsophisticated a. 不复杂的，简单的23. manual a. ；n. 手工的，手册24. assist vt.；n. 辅助25. lift vt. 起吊，提升26. rational a. 合理的27. criterion （复数criteria） n. （判断的）标准，准则28. prototype n. 原型，样机29. providing conj. （=provided）只要，如果30. delicate a. 精细的，易损的，脆弱的31. hardwood n. 硬木Lesson 181. scale n. 锈皮2. customer n. 用户，顾客3. adequate a. 充分的，足够的，适当的4. brush n. 刷子5. stiff a. 硬的6. bristle n. （刷子等的）毛7. chisel n. 錾子，凿子8. barrel n. 筒，桶9. tumbling n. 清理滚筒10. rub v. 摩擦11. breakage n. 破裂，断裂12. absorb vt. 吸收，缓冲13. jet n. 气流，射流，水流14. velocity n. 速度15. cabinet n. 小室16. sand blast cabinet 喷砂室17. nozzle n. 喷嘴18. shatter v. 打碎，打破19. shatterproof glass 防震玻璃20. completion n. 完成，结束21. helmet n. 防护面具，头盔22. pneumatic a. 气动的，风动的23. pneumatic chipping hammer 风铲24. grinder n. 砂轮机，磨床25. pneumatic grinder 风动砂轮机26. centrifugal a. 离心的27. hopper n. 斗，仓28. storage hopper 贮存斗29. blade wheel 叶轮30. emery n. 金刚砂，磨光31. emery wheel 砂轮32. dust n. 灰尘33. dust-collecting device 击沉装置。
铸造英语词汇学习25
铸造学专业英语词汇25通气性 vent ability同位素 isotope铜(Cu) copper铜基合金 cupro-metal铜缘 patina透气性 permeability涂料 facing materials涂料 wash material涂料，涂模剂 coat涂料，涂模剂 coating涂模浆 molding wash涂模料 mold coating涂模料 mold dressing涂模料 mold facing退火 annealing退火炉 annealing furance (oven)退火温度 annealing temperature退货 rejection脱蜡 burn-out脱蜡 dewaxing脱蜡法 lost wax process脱蜡造模法 lost wax molding脱模 pattern draw外观检查 outer inspection外缩(铸疵) draw外缩孔(铸疵) open cavity外圆角 round弯曲负荷 bending load弯曲试验 bending test完工面 finished surface完全冷激 complete chill完全燃烧 complete combustion完全退火 full annealing万能试验机 universal testing machine 微粒组织 graininess微量元素 subversive element微量元素 trace element韦克氏硬度计 Vicker's hardness tester 污染 pollution污染，污斑 stain 钨(W) tungsten钨铁 ferro-tungsten无疵 soundness无疵铸件 sound castings。
铸造英语词汇
铸造学专业英语词汇铸造厂，铸造 foundry铸造尺 shrink rule铸造尺 shrinkage rule铸造尺 shrinkage scale铸造从业员 foundry man铸造法 casting process铸造方案 founding method铸造方案 plan of casting铸造废料 foundry scrap铸造机 casting machine铸造计划 casting plan铸造设计，铸件设计 casting design 铸造性试验 castability test铸造应变 casting strains铸造用钉 foundry nails铸造用生铁 foundry pig iron铸造状态 as-cast condition，as-cast 铸造组织 cast structure铸造作业 casting manipulations铸芝模 ingot mold铸芝偏析 ingotism抓斗绞车装置 grabbing gear专业铸造工场 production foundry砖 brick转变用铁水(调配成分) transition iron 转动炉，转筒炉 rotary furnace转换 conversion转炉 converter转炉钢 converter steel转炉炉榇 converter lining转盘混砂机 rotating pan mill转速 revolving speed转台，转盘 rotary table转台喷粒机 shot tablast转位半径 transititon radius转运车 transfer trolley转运翻箱装置 transfer-turnover device转运盖c装置 transfer-closing device转运装置 transfer device装砂芯 coring up装载机 bucket loader装载能量 loading capacity追补焦 split coke锥形炉腹 bosh坠裂试验 shatter test坠落试验 drop test坠重试验 drop-weight test自动电极控制 automatic electrode control自动电流调整器 automatic current regulator自动化 automation自动化系统 automatic system自动加料设备 automatic charging equipment自动进给 automatic feeding自动控制 automatic control自动配料机 automatic doser自动燃烧控制 automatic combustion control自动送料(压铸) automatic ladling，die casting自动温度控制器 automatic temperature controller自动造模工场 automatic molding plant自动铸砂处理设备 automatic sand plant自动转盘式造模机 automatic turntable molding machine 自来水 tap water自然腐蚀试验 field test自然裂缝 seasoning shake自然破裂 season cracking自然干燥法(木材)，自然季化处理(铸件) natural seasoning 自然时效 natural aging自然通风 natural draft自行除渣 self-skimming自行除渣风口 self-slagging tuyere自行结晶 idiomorphic crystal自行退火 self-annealing自硬钢 self-hardening steel自硬性 self-hardening自硬性造模法 no-bake process自硬性粘结剂 self-curing binder自由度 degree of freedom自由水 free water纵向裂痕 longitudinal crack足尺 full size阻挠元素 interfering element阻销 stop pin组成图 constitutional diagram组成物 component组成楔值 constitutional wedge value组合 built up组合构造 composite construction组合模板 built-up plate组合模型 built-up pattern组合模型 composite pattern组合模型 pattern assembly组合砂箱 built-up molding box组合砂芯盒 multiple core box组织，级成 constitution组织成分 constituent组织瑕疵 structure defects钻悄(试样用) drillings钻维硬度值(韦克氏硬度) diamond pyramid hardness number，Vickers hardness 最大负载 maximum load最后加工 finish最适水分(模砂) optimum temper moisture作业可靠性 operational reliability作业砂(生产线) production sand作业准备日程 operational scheduling直立浇铸 vertical pouring直立心型端承，直立砂芯头vertical coreprint直立旋板心轴 upright spindle直立造模 vertical molding直立造模法 mold on end直立铸模 vertical mold直立铸造 vertical casting直落砂芯 drop core直木纹 edge grain直提砂芯头 tail print直通干燥炉 through feed drying furnace直显照片(金相) direct print直压式合机 direct pressure closing植物油 vegetable oil指形进模口 finger gate酯系硬化法 ester-process制震能 damping capacity蛭石 vermiculite置冲法 pour-over method置冲法 transfer method置模箱 set-off box滞流(铸疵) mistrun制程退火 process annealing制模型铣床 pattern milling machine制图，起模 drawing制造熔接 production welding制造冶金学 process metallurgy 质量效应，厚薄效应 mass effect 致密度 consistency中间处理 intermediate treatment 中间检查 intermediate inspection 中间金属 intermediate metal中间砂箱，中间模箱 cheek box ，cheek flask中间砂箱，中间模箱 raising middle flask中磷生铁(P0.4-0.75%) medium phosphorus pig iron中模，中间砂箱，中间模箱cheek中碳钢 medium carbon steel中途添焦 spreader charge of coke中线收缩 centerline shrinkage中心板，旋刮板心轴承座 center plate中心规 centergage中性耐火材料 neutral refractory materials中性熔渣 neutral slag中性砖 neutral brick中周波感应电炉 intermediate frequency furnace锺，锺形塞进器 bell锺青铜 bell bronze重搭 overlap重捣砂 hard ramming重金属铸件 heavy-metal castings 重晶石 heavy spar重力分离器 gravitational separator重力滚子输送机(倾斜式) gravity roller conveyor重力偏析 gravity segregation重力输送机 gravity conveyor重力压铸法 gravity die casting重力铸造法 gravity casting重燃油 heavy fuel oil重熔 remelting重熔工场 secondary smelter重印法(造模) print back重油 heavy oil重整石英砂 replenishment quartz sand重铸 recasting轴 shaft轴承合金 bearing metal皱痕面(铸疵) creasy surface皱皮(铸疵) orange peel皱皮(铸疵) surface folding珠，粒，击，射注过程(压铸) shot珠击处理 shot peening珠击机 shot peening machine珠粒喷击清理 shot blasting珠泡 bead竹叶状液面花纹 bamboo leaves pattern主成分，基本金属 primary coil主模 master mold主心型，主砂芯 body core煮材干燥法 boiling seasoning助流剂 fluidizer助黏剂，膨胀性粘结剂 swelling binder注入槽(压铸) pouring shot注射器 injector柱 column柱 pillar柱塞，塞罩 plunger柱塞，塞罩 post柱状结晶 columnar crystal柱状组织 columnar structurew 仓壁冲击振动器 impact vibration on bin wall贮砂桶匣(砂芯机用) magazine铸包 camlachie cramp铸壁 wall铸壁鹌鹑 wall thickness铸补 burning on铸补 tinkering铸成率 casting yield铸成试片 cast-to-shape specimen铸尺 contraction rule铸疵 casting defect铸疵 defect test铸疵，铸造缺陷 foundry defects 铸疵试验 defect test铸锭 ingot铸锭底砖 spider铸锭浇口砖 king brick铸锭模 ingot case铸锭状态 as-ingot铸钢 cast steel铸钢造模料 steel foundry molding compound铸工 caster铸工 founder铸合金 ferro-alloy铸弧 pouring arc铸件 castings铸件表面 casting surface铸件表皮 casting skin铸件飞边，铸件毛边 casting fin 铸件内包物 cast-in insert铸件清理，最后加工 finishing铸件清理图 dressing shop铸件修整 finishing of castings铸件应力 casting stress铸焦 foundry coke铸坑 casting pit铸坑 foundry pit铸裂(铸疵) casting crack铸瘤 rising铸漏 bleed铸漏 break out铸漏 run-out铸漏件 bleeder铸模 mold，mould铸模布置 mold layout铸模除除掉(压铸) impression block铸模龟裂，脉状痕(铸疵) veining 铸模夹具 mold clamp铸模输送机 mold conveyer铸模块合 mold assembly铸耙 rake铸皮 skin铸皮孔 skin holes铸砂 casting sand铸砂处理 foundry sand preparation铸砂处理 preparation of sand铸砂处理工场 foundry sand preparation plant铸砂控制 sand control铸砂控制设备 sand control equipment铸砂流动性 flowability of sand 铸砂流动性 foundry sand铸砂膨(铸疵) sand drier铸砂强度试验 strength test of sand铸砂强化 strengthen the sand 铸砂烧结(铸疵) sand burning铸砂烧贴(铸疵) sintering point 铸砂油 casting iol铸生铁机 pig machine铸损 foundry losses铸损，不良铸件 waster，foundry losses铸铁 cast iron铸铁工场 iron foundry铸铁管 cast iron pipe铸铁组织图 cast iron diagram铸铁组织图 structural diagram ofcast iron铸造 founding铸造，铸件 casting铸造场 smith shop圆盘砂轮机 disc grinder圆套筒 round bush圆条测温法 bar test圆筒式炉(回转炉) drum type furance圆筒形浇桶 drum ladle圆头镘刀 roound nose圆形砂 rounded grain圆形砂粒 rounded sand云母粉 mica flour云母粉 mica powder运轮，台车 carriage运送箱 tote box运原性蒙气 reducing atmosphere运原状态 reducing condition杂质 impurities再炽，再辉 recalescence再炽点，再辉点 recalescent point再处理 erpreparation再处理砂 reconditioned sand再负载 reloading再结晶 recrystallization再结晶温度 recrystallization temperature 再冷却系统 recooling system再黏接砂 rebonded sand再热炉 reheating furnace再生砂 reclamation sand再生铁 remelted pig iron再生铁 synthetic pig iron暂垫造模法 mold on an oddside凿锤 chipping hammer凿刀 chipping chisel凿磨浇口 shagging凿平 chipping凿平问 chipping room凿子，凿机 chipper凿子，凿机 chisel造模 molding造模板 mold board造模板 molding board造模板 molding plate造模板 ramming plate造模材料 molding materials造模材料添加剂 molding material additive 造模粗砂 molding gravel造模地坑 molding pit造模钉 molding brad(pin)造模法 molding method造模工具 molder's tools造模工作台 molder's bench造模工作台 molding bench造模机 molding machine造模袷度 molding allowance造模区 molding bay造模设备 molding apparatus造模性 moldability造渣剂 slag forming constituent造渣期 slag forming period造渣石灰 slag lime造渣作业 slag practice增碳 carbon pick-up增碳 recarburization增碳剂 recarburizer增碳剂 recarburizing agent增碳焦 recarburization coke增压冒口，威廉氏冒口 atmospheric feeder(atmsopheric riser，William's riser)增压冒口，威廉氏冒口 William's riser，atmospheric riser增压砂芯 cracker core增压砂芯 pencil core增压砂芯 penetration core增压砂芯，嵌入砂芯 insert core增压砂芯，威廉氏砂芯 atmospheric core，William's core渣 dirt渣比，碱度 slag ratio渣阱 dirt trap渣孔(铸疵) slag blowhole渣棉 slag wool渣壳 slag crust渣桶 slag ladle渣位高 slag level渣窝 slag pocket轧辊，辊子 roll轧屑 roll[ing] scale闸喉，闸口 choke闸喉式流道 choked runner system闸喉作用 choking粘土质耐火砖 fire clay brick展性，可锻性 malleability展性处理 malleablising展性热处理铁矿 malleable ore展性退火 malleablising annealing展性铸铁(可锻铸铁) malleable cast iron展性铸铁(可锻铸铁) malleable iron展性铸铁用生铁 malleable pig iron辗制硅砂 artifical silica sand章鱼状石墨 octopus graphite胀疤 expansion scab胀模(铸疵) swell胀陷，上模剥砂(铸疵) pull down罩式炉 lifting furnace遮蔽电弧熔接 shielded-arc welding遮热板 heat shield折旧 amortization折旧 depreciation折缘(黑心展性铸铁) picture frame锗(Ge) germanium真空除氧法 vacuum degassing process真空精炼 vacuum refining真空熔解 vacuum melting真空造模法，V造模法 V-process，vacuum-secaled process 真空铸造 vacuum casting真离心铸造法 true centrifugal casting砧 anvil砧台式震实造模机 anvil-jolter针对铸铁 acicular cast iron针孔(铸疵)，销孔 pin-hole针状组织 acicular structure针状组织铸铁 bainite cast iron振动 vibration振动捣砂 vibration ramming振动分配器 vibrating distributor振动器 vibrator振动清箱 mechanical knockout by vibration振动清箱，振动清砂处 shake-out振动清箱机 molding box shake-out device振动清箱机，振动清砂机 shake-out machine振动清箱性能 shake-out property振动清箱栅 shake-out grid振动清箱栅 shake-out screen振动筛 jigging screen振动筛 shaking screen振动筛 vibrating sieve震捣 jolt ramming震动 jolt震动板 jolting plate震动废黜模板造模机 jolt molding machine with turnover plate 震动机 jarring machine震动清箱吊架 jointing hanger震动压挤拔模造模机 jolt squeeze stripper molding machine 震动压挤造模机 jolt squeeze molding machine震动造模机 jolt molding machine震动造模机 jolter震箱清砂机 flask shanker蒸馏器 retort蒸馏碳 retort carbon蒸气脱蜡 autoclave dewaxing整流器 rectifier整体模型 solid pattern整体模型铸模 solid pattern mold整温控制 thermostatic control整缘 trimming整缘模具 trimming dies整缘压机 trimming press正常化 normalizing正常偏析 normal segregation正常温度 normal temperature正常折曲试验 normal bend test支架(压铸)，垫块 packing block支台，置模台 set-off bench支柱(熔铸炉) prop枝形进模口 bracnch gate直尺 staight edge直接电弧炉 direct arc furnace直接浇口 drop gate直接浇铸 direct pouring直接浇铸法 direct casting直接进模口 direct gate直接进模口 slot gate直接气压式热室压铸机(压缩空气直接压于熔液) direct pressure hot chamber machine 氧化硅基砂 silica base sand氧化性蒙气 oxidizingatomosphere氧化性溶解 oxidizing melting氧皮铝 alumite氧焰割 oxycut氧乙炔熔接，气焊 oxyacetylenewelding样板，刮板，量具 template，templet样规 sizing peg摇动炉 rocking furnace摇斗炉 shaking lade摇台 cradle窑炉 kilnb 趸 ?anti-oxidant冶金焦 metallurgical coke冶金术 metal technology冶金学 metallurgy液化 liquefaction液面花纹 break surface pattern液面花纹 figure液面花纹 play figure液态收缩 liquid contraction液态收缩 liquid shrinkage液体压力计 manometer液相曲线 liquidus curve液相线 liquidus [line]液相线 liquidus line液压气动砂箱升提机构hydropneumatic flaskliftingmechanism液压千斤顶 hydraulic jack液压清砂铸件设备 hydrauliccleaning equipment液压试验 hydraulic pressure test 叶轮式喷砂机 turbine sand blaster一氧化碳 carbon monoxide一氧化铁(FeO) iron protoxide铱(Ir) iridium移动吊车 mobile crane移动皮带升降机 mobile belt elevator移动式烘炉 portable drying oven 移动式烘模机 portable mold dryer移动式可倾前炉 removable clay matter移动式摔砂造模机 motive type sand slinger移入 shunting-in移位装置 shifting facilities移装(外砂芯) draw back移装砂芯 inset core遗传性 heredity乙二醇 glycol乙炔 acetylene乙炔发生器 acetylene generator 乙炔墨 acetylene black(acetylene smoke)乙炔墨 acetylene smoke，acetylene black乙炔熔接 acetylene welding抑制剂 inhibitor易开砂箱 easy off slip flask易燃物 inflammable易熔合金 fusible alloy异形管件 specials意外防止条例 accident prevention regulations溢放口 flow off溢放口 pop off溢放口 run-off溢放口 strain relief溢放冒口 run-off riser溢流 over flow溢流道 flow through溢流口 hot spruing溢流口(压铸) over flow well音波试验 sonic testing阴极锈法 cathodic protection阴极氧化 anodic oxidation铟(In)(稀金属元素) Indium银(Ag) silver银砂(无铁质硅砂) silver sand引导顶出(压铸) guided ejection 英高镍(镍铬合金) Inconel英国国家标准 B.S.(British Standard)英国铸铁研究协会 BCIRA(British Cast Iron Research Associatin)英国铸造工程师学会 IBF(Institute of British Foundrymen，London)英制热单位(B.T.U.) British Thermal Unit应变，变形(铸疵) strain应变计 strain gage应力 stress应力腐蚀裂痕 stress corrosion cracking应力集中 stress concentration应力破坏强度 stress upture strength应力消除 stress relief应力应变特性 stress-strain characteristics应力应变图 stresss-strain diagram樱木 cherry tree荧光采伤法 zyglo荧光渗透剂 zyglo penetrant荧光 fluorescence荧光镜 fluoroscope荧光探伤法 fluorescent crack detection荧光透视法(检查)，荧光镜试验fluorspar萤石(CaF2) fluorite萤石(CaF2) flushing硬点 hard spot硬度 hardness硬度计 hardness tester硬焊 brazing硬化(壳模) curing硬化，淬火 hardening硬化合金 hardening alloy硬化剂 hardening agent硬化剂，硬化合金 hardener硬化加速剂 hardening accelerator硬化能，淬火性 hardenability 硬化深度 hardness penetration 硬化时间 curing time硬结 setting硬结砂用油 setting oil硬木 hardwood硬砂模型板 hard sand match 硬质焦炭，煤焦 hard coke永久模，金属(铸)模 permanent mold用瓢装液(压铸) ladling用销抬起 pin lift优尼造模法 Unicast process优先方位(结晶) preferred orientation油淬火 oil quenching油粉浸渗试验(裂痕检出试验) oil-chalk test油炉 oil furnace油泥砂浆 oil loam油漆，涂料 paint油砂 oil sand油砂模 oil sand mold油砂芯 oil bounded core油砂芯 oil core油砂芯 oil sand core油污金属切屑 swarf油烟，烟灰 soot油硬化 oil hardening油质黏结剂 oil biner柚木 teak游标卡尺 vernier calipers铀U) uranium有机粘结剂 organic binder有孔砂芯撑 perforated chaplet 有麻口冷硬层 chill zone with mottle有箱造模法 flask molding有效高度 burden height有效高度 effective height有效黏土含量 effective clay content釉，光滑 glaze鱼油 fish oil鱼嘴栅 fishmouth gate榆木 elm余留铁水 heel余铁深度(炉) pool depth余隙，间隙 clearance余液(低周波炉) liquid core雨段退火 two-stage annealing雨淋式环浇口 pencil ring gate雨淋式进模口 pencil gate雨淋式进模口 pop gate雨淋式进模口 shower gate浴池式氮化法 bath nitriding预热 preheating预热带 preheating zone预热空气 preheated air预热器 preheater预熔金属 pre-melt原料 raw materials原料工业 primary graphite，G-graphite原料金属 primary industy原料生铁 base iron原模型 granular pearlite原砂，原产硅砂 crude sand原砂透气度 base permeability原生组织 primary structure原油 crude oil圆板塞(浇池) disc plug圆底提砂钩 Yankee's lifter圆规 compasses圆粒 round sleeker圆抹镘 trowel星形裂缝 star shake星形铁(滚光用) jackstar，mill star，star 星形铁(滚光用) mill star，jack star，star 星形铁(滚光用) star，jackstar，mill star 星形铁(滚光用) tumbling stars形象因子 shape factor型砖 shaped brick修补 removable tilting forehearth修毂抹刀 boss spatula修角刀 corner tool修角抹刀 angle spatula锈 rust锈皮，比例尺，秤 scale锈皮，轧钢鳞片 mill scale锈蚀度 degree of rustin虚表比重 apparent specific gravity虚表孔率 apparent porosity虚表密度 apparent density虚表容积 apparent volume虚表温度 apparent temperature虚筋，挡块(砂模) stop off蓄热炉 regenerating furnace蓄热能量 heat-retaining capacity蓄热器，再生器 regenerator蓄热系统 regenerative system续制铸件 repeated use of sand旋臂吊车 jib crane旋风集尘器 cyclone dust collector(cyclon)旋风净尘器 cyclone scrubber dust collector 旋刮[砂] sweeping旋刮板 sweep旋刮板 sweeping board旋刮板臂 sweep arm旋刮板马架 sweeping molder's horse旋刮板模型 sweeping pattern旋刮板模型 sweeping template pattern旋刮板砂芯 swept core旋刮板心砂芯 spindle core旋刮板心轴，心轴 spindle旋刮板轴心承座 sweeping plate旋刮砂模 sweeping mold旋刮砂芯 sweeping core旋涡补给口 whirl-gate feeder旋涡混合机 whirl mixer旋涡集渣包 whirl-gate dirt trap旋沿试验法(流动性) spiral test旋转给料盘 rotary feeding plate旋转刮板 turning strickle旋转模板造模机 truning plate molding machine 旋转器 swirl旋转干燥器 rotary drier旋转砂芯线 setting line，core setting line旋转筛 rotary screen旋转筛砂机 rotary sand screen旋转式集尘器 spin dust collection旋转台，转盘 turn table旋转喂槽 swivelling tundish旋转轧碎机 rotary crusher悬吊砂 suspended core悬吊砂轮机 suspended grinder悬吊输送机 trolley conveyor悬浮物 suspended matter悬拱 suspended arch悬挂式清箱装置 pendant shaking equipment 选别废料 selected scrap雪明碳铁，雪明碳体 cementite循环处理砂 system sand循环砂 recirculation system sand循环砂 return sand压边整缘 press trimming压痕试验 indentation test压痕嚣，压痕物 indentor压痕硬度试验机 indentation hardness tester压坏(砂模)，粉碎 crush压挤板 squeeze plate压挤板 squezze boad压挤捣砂 squeeze ramming压挤机 squeeze machine压挤式顶杆造模机 squeeze pinlift molding maching 压挤头(造模机) squeeze head压挤造模机 squeeze molding machine压挤铸造 squeeze casting压紧废料 packeted scrap压块 briquet，briquette压块 bundle压块废料 baled scrap压块机 briquetting machine压力 pressure压力计 pressure gage压力室添加法 pressure chamber method压力通风 follow board压力铸造 pressure casting压漏(铸疵) leakers压漏试验 leakage test压模印 coining压膜式壳模机 diaphragm shell molding machine压膜式造模机 diaphragm molding machine压实性 compactability压实指数 compactability index压碎机 crusher压缩机 compressor压缩机 die casting machine压缩空气 compressed air压缩空气缸 compressed air cylinder压缩空气喷吵机 compressed air sand blaster压缩空气软管 compressed air hose压缩性 compressibility压重，砝码 weights压重板(震动压面) jointing plate压铸，刚模铸造 de cast压铸储井 shot well压铸储筒 shot sleeve压铸法，刚模铸造法 die casting压铸件 die castings压铸模 dies压铸模涂料，刚模涂料 die coating压铸模块 die cast assembly亚共晶合金 hypoeutectic alloy亚共析合金 hypoeutectoid alloy亚甲蓝试验 methylene blue test亚硫酸监稠浆(黏结剂) sulphur，sulfur亚铝美尔 Alumel氩(Ar) argon氩净化器 argon purifier烟囱 chimney烟囱 chimney stack烟囱，炉胴(熔铁炉) stable-equilibrium diagram烟囱罩 hood烟道 chimney flue烟道气 flue gas烟火 bank，the cupola烟煤 bituminous coal烟煤 soft coal烟气(有害的) fume烟雾 smog延性 ductility延性材料断口 ductile fracture延性铸铁(球状石墨铸铁) ductile cast iron，nodular cast iron 研究工程师 research engineer研磨纸 emery paper焰割 gas cutting洋铜 nickel silver阳极处理 anodizing阳极铜 anode copper扬尘量 dust emission杨氏模数，杨氏[纵弹性]系数 Young's moldulus氧(O) oxygen氧丙烷焰割 oxy-L.P.gas cutting氧化 oxidation氧化 oxidizing氧化表皮 oxide skin氧化带 zone of ozidation氧化精炼 oxidizing refining氧化精炼 refining by oxidation氧化期 oxidizing period氧化气孔(铸疵) oxidized blowhole氧化损耗 oxidation loss氧化铁 iron oxide氧化物 oxide氧化硅(SiO2) silica物理变化 physical change物理试验 physical test物理性质 physical properties物理冶金 physical metallurgy雾化 atomization西拉高硅铸铁 Silal吸热反应 endothermic reaction吸入输送机 suction conveyor吸湿性试验(高湿状态) high humidity storage test 吸收 absorption吸收剂 absorbent吸收器 absorber析出，沈淀 precipitation析出热处理 precipitation heat treatment析出退火 precipitation annealing析出硬化 precipitation hardening硅(Si) silicon硅肥粒铁 silico ferrite硅肺病，石米沉着病 silicosis硅分析仪，砂计 silicon meter硅钢板 silicon steel plate硅化钙 calcium silicide硅化钙 calcium silicon硅黄铜 silicon brass硅块 silicon briquets硅铝钙合金 calicum-aluminium-silicon硅铝明(铝硅合金) silumin硅锰钙合金 calcium-manganesesilicon硅凝胶，硅胶吸湿剂 silica gel硅青铜 silicon bronze硅青铜 soilzin bronze硅砂 silica sand硅砂捣料 silica ramming compound硅砂粉 silica flour硅砂浆涂料 silica wash硅砂石砖 ganister brick硅树脂，硅酮 silicone硅树脂滑脂 silicone grease硅酸 silicic acid硅酸监 silicate硅酸钠，水玻璃 sodium silicate硅酸四乙酯 tetraethl silicate硅酸乙脂 ethyl silicate硅铁 ferro-silicon硅铜 silicon copper硅线石砖(高铝氧(70Al2O5)硅质耐火砖) silimanite brick 硅岩轮辗硅砂 impeller-breaker sand硅藻土 diatomaceous earth硅藻土 infusorial earth硅藻土 kieselguhr硅质粘土 silicious clay硅砖 silica brick硒(Se)(化学元素) selinium稀土金属 rare earth metal锡(Sn) tin锡汗珠(铸疵) tin sweat锡青铜 tin bronze习用潜变限度 conventional creep limit洗尘器，涤气机 scrubber洗净器 scrubbing liquid细锉刀 finishing file细孔组织 cell structure细裂痕(铸疵) hair crack细裂纹(铸疵) caplillary crack细密波来铁 fine pearlite细泥砂浆 finishing loam细砂，河海丘砂 bank sand细土粉，细泥 fine silt煅烧 calcine煅烧白云石 calcined dolomite煅烧窑 calcining kiln瑕疵 flaw瑕疵大小 flaw size瑕疵位置 flaw location揬工场，揬造炉 fore-hearth forge揬铁锈皮 forge scale揬造，揬件 forging下降速率 lowering speed下浇道，坚浇道 down gate下浇道，坚浇道 down sprue下模 bottom part下模 nowel下模，下砂箱，下模箱 drag下砂箱，下模箱 drag box下砂箱，下模箱 drag flask夏比冲击试验 charpy impact test夏比冲击试验机 Charpy impact test machine 夏比冲击值 Charp impact value纤维状滑石 fibrous talc显热 sensible heat显微镜 microscope显微镜试验 microscopic inspection显微镜学 microscopy显微镜照像 photomicrograph显微偏析 micro-segregation显微缩孔(铸疵) micro-shrinkage显微像 micrograph显微组织 micro-structure限缩变形 hindered contraction限外显微镜 ultramicroscope相 phase相对频率 relative frequency相对湿度 relative humidity相对硬度 relative hardness相律 phase rule相平衡 phase equillibrium相图 phase diagram响铜 bell metal象皮皱纹(铸疵) elephant skin橡胶浇道棒(造模) rubber down gate橡胶浇道棒(造模) rubber pouring funnel橡胶输送带 rubber conveyer belt橡木 oak消除冷硬退火 chill removing annealing消除应力开沟，防裂槽 stress relieving grooving 消泡剂 antifoaming agent消石灰，熟石灰 slake-lime消退 fading消退时限 fading time硝酸浸蚀液 nital硝酸浸蚀液 nitric acid销 pin销合 pin closure销紧力 locking force销孔试验片 keyhole specimen销抬造模机 pin-lift molding machine萧氏精密造模法 Shaw process萧氏硬度 Shore hardness小块料 cobbing小胚 billet小铸件 small castings校准 calibration校准块 calibration block校准钮 calibrating knob楔 wedge楔表进模口 wedge gate楔塞作用 wedge action楔形进模口 wedge runner bar楔形试片 wedge test piece楔形试验 wedge test楔形销 wedge pin楔形压力试验 wedge penetration test 楔形砖 key brick楔形砖 wedge brick楔值 wedge value斜导杆(压铸) cam finger斜度砂箱，滑脱砂箱 slip flask斜方晶系(结晶) rhombic system卸斗 skip卸斗吊车 skip hoist心，心型，砂芯 core心材 heart wood心骨 core bar心骨 core grid心骨 core iron心骨 core rod心骨管 core barrel心骨矫直器 core rod straightner心骨模 core grid mold心骨模型 core iron printer心骨切断器 core rod cutter心骨轴 core spindle心裂(木材) heart shake心砂 core sand心砂混合机 core sand mixer心形镘刀 large heart trowel心型拔出装置(压铸) core pull assembly 心型撑，砂芯撑 chaplet心型固定门(压铸) heel block心型滑板(压铸) core slide心型移装，砂芯移装 core draw-back心轴，心骨 arbor心座 core bedding frame辛浦森式混砂机 Sympson type sand mill新炼金属 virgin metal新砂 new sand锌(Zn) zinc锌当量 zinc equivalence，zinc equivalent factor 通气口 air port通气蜡条 vent wax通气蜡线 wax vent通气砂芯 blind core通气筛嘴(砂芯盒) screen vent通气性 vent ability通气针 vent former通气针 vent wire同素异性 allotropy同位素 isotope同质多象 polymorphism桐油 China wood oil酮油 tung oil铜(Cu) copper铜基合金 cupro-metal铜绿 green patina铜气脆性(铸疵) hydrogen brittleness of copper 铜缘 patina铜缘 Verdigris筒状浇口(压铸) end gate头等品质 top grade quality透明片 transparent cut透气性 permeability透气性试验 permeability test透气性试验器 permeability tester"凸出块，突耳 casting lug凸疵(铸疵)(模型粘砂) sticker凸肩导销 shoulder guider pin凸块，突耳 lug凸片，飞边 fin凸片管 finned tube凸片气缸 finned cylinder凸缘 flange凸缘抹片 flange sleeker突出标志 rising mark突耳孔 lughole突起分模面 undulating mold joint涂焊(表面硬化涂焊) surfacing涂黑 blacking涂浆，洗涤 washing涂沥表管 tarred pipe涂料 facing materials涂料 wash material涂料，涂模剂 coat涂料，涂模剂 coating涂料疤(铸疵) blacking scab涂料孔(铸疵) blacking hole涂模浆 mold wash涂模浆 molding wash涂模料 mold coating涂模料 mold dressing涂模料 mold facing涂模料接种法 mold coating inoculation 涂刷 painting土状石墨 amorphous graphite吐粒散铁，吐粒散体 trosstite钍(Th) thorium推拔，斜度 taper推拔砂箱 taper flask推拔套箱 taper case推车式浇桶 buggy ladle推挤(压铸) squeezing退火 annealing退火罐 annealing pot退火炉 annealing furance (oven)退火温度 annealing temperature退火箱 annealing box退火用填料，退火用矿粉 annealing ore退货 rejection托板 pallet托板输送机 pallet conveyor托板输送机 plate conveyer托架 bracket托运板 carrying plate脱件销(压铸) sprue puller pin脱蜡 burn-out脱蜡 dewaxing脱蜡法 lost wax process脱蜡造模法 lost wax molding脱裂强度(模砂式模纵面压裂试验) splitting strength 脱硫，去硫 desulphurization脱硫，去硫 desulphurizing脱模 pattern draw脱模式造模机 pattern-draw molding machine脱湿剂(模砂用) humectant脱碳 decarburization脱碳法展性处理 malleablization by decarburizing 脱碳率 rate of decarburization脱硅 desiliconizing脱锌 dezincification椭圆导套 oval bush外观检查 outer inspection外角抹镘 square sleeker外卡钳 outside calipers外冷激，外冷硬，外冷铁 extenal chill外模破裂 broken mold外伸砂芯顾 clearance print外伸砂芯头 over-hang外伸余度砂芯头 clearance taper print外缩(铸疵) draw外缩孔(铸疵) open cavity外缩孔(铸疵) surface shrinkage外缩孔，凹陷(铸疵) depression外缩窝 shrinkage depression外烯式空气预热器 externally fired hot blast heater外因非金属杂物 exogenous non-metallic inclusion外因金属夹杂物 exogenous metallic in clusion外因凝固 exogenous solidification外圆角 round弯曲负荷 bending load弯曲试验 bending test弯头抹刀 bent spatula完工面 finished surface完全冷激 complete chill完全燃烧 complete combustion完全退火 full annealing完整模型 complete pattern万能试验机 universal testing machine威兼氏砂芯，增压砂芯 William's core，atmospheric core微粉煤 dust coal微孔巢性(铸疵) microporosity微粒度(底片) grains of sand微粒组织 graininess微量元素 subversive element微量元素 trace element微小硬度计 micro-hardness tester韦克氏硬度 Vicker's hardness，diamond pyramid hardness number 韦克氏硬度计 Vicker's hardness tester伟晶作用 germination未处理原砂 raw untreated sand未静钢 unkilled steel未静钢，净缘钢 effervescing steel未静钢，净缘钢 rimmed steel未空孔 blind hole喂槽 tundish温度阶差 thermal taper温热强度 warm strength文氏管流量计 Venturi meter文氏管洗净器 Venturi scrubber文氏管装置 Venturi apparatus文武镘刀 square trowel稳定平衡图 stabilizing inoculant涡流 eddy current蜗旋电阻线 resistance spiral蜗肇滑槽 spiral chute蜗肇输送机 spiral conveyor沃斯回火法 austempering沃斯田钢 austenitic steel沃斯田化 austenizing沃斯田化温度 ustenizing temperature沃斯田锰钢 austenitic manganese steel沃斯田铁，沃斯田体 austenite沃斯田铸铁 austenite cast iron沃斯田铸铁 austenitic cast iron卧式砂芯射制机 horizontal core shooter污泥 sludge污染 pollution污染，污斑 stain钨(W) tungsten钨铁 ferro-tungsten无疵 soundness无疵铸件 sound castings无缝榇料 monolithic lining material无缝炉榇，整体炉榇 monolithic lining无负载时间 no-load time无麻口冷硬层 chill zone without mottle无水酒精 absolute alcohol无头小钉 spring无箱砂模，脱箱砂模 boxless mold无箱造模法 laskless molding无烟煤 anthracite五倍周波感应电炉 quintuple frequency induction furance伍氏合金 Wood's metal碎砂机，松砂机 sand breaker碎铁 bushelling碎心锤 core buster碎心机 core breaker隧道炉 tunnel furnace隧道炉，隧道干燥炉 tunnel oven隧道炉，隧道干燥炉 tunnel stove隧道退火炉 tunnel annealing furnace隧道退火炉 tunnel-type annealing furnace 隧道窑 tunnel kiln隧道铸铁圈 tunnel casting ring缩尺 pattern maker's rule缩管(铸疵) shrinkage pipe缩颈冒口 feeder head with Washburn core 缩颈砂芯 breaker core缩颈砂芯 break-off core缩颈砂芯 wafer core缩颈砂芯 Washburn core缩颈砂芯，敲落 knock off缩颈砂芯，敲落 neck down core缩孔(铸疵) shrinkage cavity缩孔(铸疵) shrinkage hole缩孔[铸疵] shrink hole缩孔倾向 shinkage cavity tendency缩裂(铸疵) contraction crack缩裂(铸疵) shrinkage crack缩面百分率 percentage of area reduction 缩面率 reduction of area缩入，渗透 infiltration缩水量 pattern maker's shrinkage缩陷处 shrink mark他型结晶 allotriomorphic crystal铊(Tl) thaljium塔式炉 tower oven台 bench台车，卡车 truck台车，托架，载体 carrier台车轮送机 car conveyor台车式炉 car-bottom furnace抬柄 bull handle抬动浇斗 shank ladle抬动浇桶 carry ladle抬动浇桶 fork ladle台秤 platform scale台上造模法 bench molding台上铸模 bench mold台式磨床 pedestal grinder钛(Ti) titanium钛铁 ferro-titanium钛氧包覆料 rutile covering钛铸铁 titanium cast iron钽(Ta) tantalum探针，铅锺，测锺，试体 probe碳 carbon碳榇 carbon lining碳当量 carbon equivalent碳当量测定剂 CE meter (carbon equivalent meter)碳粉 carbon powder碳钢 carbon steel碳钢 straight carbon steel碳钢，普通钢 plain carbon steel碳弧熔接 carbon arc welding碳化 carbonization碳化钙，电石 calcium carbide碳化铁 iron carbide碳化物 carbide碳化物安定剂 stabilizers碳化物稳定剂 carbide stabilizer碳化硅 silicon carbide碳化硅压块 silicon carbide briquests碳化渣(白渣) carbide slag。
铸造英语词汇大全
铸造术语1 范围2 基本术语2.1 铸造casting, founding, foundry2.2 砂型铸造sand casting process2.3 特种铸造special casting process2.4 铸件casting2.5 毛坯铸件rough casting2.6 砂型铸件sand casting2.7 试制铸件pilot casting2.8 铸态铸件as-cast casting2.9 铸型[型] mold2.10 铸造工艺casting process， foundry technology2.11 铸造用材料foundry materials2.12 铸造工艺材料consumable materials2.13 铸造设备foundry equipment ,foundry facilities2.14 铸工caster， founder， foundry worker2.15 铸造工作者foundryman2.16 铸造车间foundry shop2.17 铸造厂foundry2.18 铸造分厂attached foundry， captive foundry， tied foundry 2.19 铸造三废foundry effluent2.20 一批 a batch2.21 一炉 a cast， a heat， a melt2.22 铸焊cast welding， flow welding2.23 铸锭ingot3 铸造合金及熔炼、浇注3.1 铸造合金基本术语3.1.1 铸造合金cast alloy3.1.2 共晶合金系eutectic alloy system3.1.3 共晶合金eutectic alloy3.1.4 亚共晶合金hypoeutectic alloy3.1.5 过共晶合金hypereutectic alloy3.1.6 共晶团eutectic cell3.1.7 共晶温度eutectic temperature3.1.8 共晶转变eutectic reaction， eutectic transformation3.1.9 共晶组织eutectic structure3.1.10 铸造复合材料cast composite3.1.11 定向共晶复合材料directional eutectic composite3.1.12 非晶态合金noncrystalline alloy3.1.13 合金元素alloying element3.1.14 杂质元素tramp element3.1.15 合金遗传性alloy heredity3.1.16 铸态组织as-cast structure3.1.17 铁碳相图iron-carbon phase diagram3.1.18 碳化物carbide3.1.19 渗碳体cementite3.1.20 碳化物形成元素carbide forming element3.1.21 单铸试块separated test bar of casting3.1.22 附铸试块test lug3.1.23 本体试样test specimen from casting itself3.1.24 过热superheating3.1.25 过冷supercooling， undercooling3.1.26 成分过冷constitutional supercooling3.1.27 过冷度degree of undercooling3.1.28 加热相变点[Ac 相变点] Ac transformation temperature3.1.29 冷却相变点[Ar 相变点] Ar transformation temperature3.1.30 结晶crystallization3.1.31 形核[成核] nucleation3.1.32 均质形核[自发形核] homogeneous nucleation3.1.33 非均质形核[非自发形核] heterogeneous nucleation3.1.34 动力形核dynamic nucleation3.1.35 大冲击形核big bang nucleation3.1.36 形核剂nucleant3.1.37 形核率nucleation rate3.1.39 内生生长endogenous growth3.1.40 外生生长exogenous growth3.1.41 共生生长coupled growth3.1.42 小平面型生长faceted growth3.1.43 非小平面型生长nonfaceted growth3.1.44 晶体生长界面[界面] growth interface of crystal， interface3.1.45 吸气(金属) gas absorption (metal)3.2 铸钢3.2.1 铸钢cast steel3.2.2 铸造碳钢carbon cast steel3.2.3 铸造合金钢alloy cast steel3.2.4 低合金铸钢low alloy cast steel3.2.5 微量合金化铸钢micro-alloying cast steel， trace alloying cast steel 3.2.6 铁素体铸钢ferritic cast steel3.2.7 奥氏体铸钢austenitic cast steel3.2.8 不锈钢stainless steel3.2.9 无磁性铸钢non-magnetic cast steel3.2.10 高锰钢austenitic manganese steel， high manganese steel 3.2.11 高强度铸钢high strength cast steel3.2.12 超高强度铸钢ultra high strength cast steel3.2.13 耐磨铸钢wear resisting cast steel3.2.14 耐热铸钢heat resisting cast steel3.2.15 耐蚀铸钢corrosion resisting cast steel3.2.16 石墨钢graphitic steel3.2.17 铸造锚链钢cast steel for chain cables3.3 铸铁3.3.1 铸铁cast iron3.3.2 合成铸铁synthetic cast iron3.3.3 共晶铸铁eutectic cast iron3.3.4 亚共晶铸铁hypoeutectic cast iron3.3.5 过共晶铸铁hypereutectic cast iron3.3.6 灰铸铁[片墨铸铁] flake graphite cast iron， gray cast iron3.3.7 球墨铸铁[球铁] ductile iron， nodular graphite iron, spheroidal graphite cast iron 3.3.8 高韧性球墨铸铁high ductility nodular graphite iron3.3.9 中锰球墨铸铁medium manganese ductile iron3.3.10 中硅球墨铸铁medium silicon nodular graphite iron3.3.11 可锻铸铁[马铁] malleable cast iron3.3.12 白心可锻铸铁white heart malleable cast iron3.3.13 黑心可锻铸铁black heart malleable cast iron3.3.14 花心可锻铸铁partially graphitized malleable cast iron3.3.15 铁素体可锻铸铁ferritic malleable cast iron3.3.16 珠光体可锻铸铁pearlitic malleable cast iron3.3.17 球墨可锻铸铁spheroidal graphite malleable cast iron3.3.18 蠕墨铸铁[蠕铁，紧密石墨铸铁] vermicular graphite cast iron, compacted graphite cast iron 3.3.19 白口铸铁white cast iron3.3.20 麻口铸铁mottled cast iron3.3.21 奥氏体铸铁austenitic cast iron3.3.22 贝氏体铸铁bainitic cast iron3.3.23 贝氏体球墨铸铁bainitic ductile cast iron， austferritic ductile cast iron3.3.23 贝氏体球墨铸铁bainitic ductile cast iron， austferritic ductile cast iron3.3.23 贝氏体球墨铸铁bainitic ductile cast iron， austferritic ductile cast iron3.3.24 等温热处理球墨铸铁austempered ductile iron ， ADI3.3.25 贝氏体白口铸铁bainitic white cast iron3.3.26 针状铸铁acicular cast iron3.3.27 马氏体铸铁martensitic cast iron3.3.28 铁素体铸铁ferritic cast iron3.3.29 珠光体铸铁pearlitic cast iron3.3.30 索氏体铸铁sorbitic cast iron3.3.31 合金铸铁alloy cast iron3.3.32 低合金铸铁low alloy cast iron3.3.33 铬铸铁chromium cast iron3.3.34 高铬铸铁high chromium cast iron3.3.35 高硅铸铁high silicon cast iron3.3.36 中硅铸铁3.3.37 高磷铸铁3.3.38 铝铸铁3.3.39 高铝铸铁3.3.40 镍铸铁3.3.41 硼铸铁3.3.42 高级铸铁3.3.43 高强度铸铁3.3.44 工程铸铁3.3.45 特种铸铁3.3.46 抗磨铸铁3.3.47 冷硬铸铁[激冷铸铁]3.3.48 耐磨铸铁3.3.49 耐热铸铁3.3.50 耐蚀铸铁3.3.51 耐酸铸铁3.3.52 密烘铸铁3.3.53 孕育铸铁3.3.54 总碳量3.3.55 碳当量3.3.56 碳当量仪3.3.57 共晶度3.3.58 硅碳比3.3.59 锰硫比3.3.60 铸铁石墨形态3.3.61 片状石墨[片墨]3.3.62 球状石墨[球墨]3.3.63 絮团状石墨[退火碳]3.3.64 团絮石墨3.3.65 蠕虫状石墨[蠕墨，紧密石墨] 3.3.66 开花状石墨3.3.67 初生石墨3.3.68 过冷石墨3.3.69 共晶石墨3.3.70 共晶碳化物3.3.71 游离碳3.3.72 石墨化3.3.73 石墨化退火3.3.74 石墨化度3.3.75 石墨化因子3.3.76 石墨面积率3.3.77 阻碍石墨化元素3.3.78 墨化剂3.3.79 石墨球化处理[球化处理] medium silicon cast ironhigh phosphorus cast ironaluminum cast ironhigh aluminum cast ironnickel cast ironboron cast ironhigh grade cast ironhigh duty cast iron， high strength cast iron engineering cast ironspecial cast ironabrasion resistant cast ironchilled cast ironwear resisting cast ironheat resisting cast ironcorrosion resistant cast ironacid resisting cast ironMeehanite cast ironinoculated cast irontotal carboncarbon equivalenteutectometercarbon saturation degreesilicon-carbon ratiomanganese-sulphur ratiographite morphology of cast ironflake graphitenodular graphite， spheroidal graphite temper graphite ， annealing carbon quasi-spheroidal temper graphite compacted graphite， vermicular graphite exploded graphiteprimary graphiteundercooled graphiteeutectic graphiteeutectic carbidefree carbongraphitizationgraphitizing annealinggraphitizing gradegraphitizing factorpercentage of graphite areahindered graphitizing element graphitizernodularizing treatment of graphite3.3.80 球化率percent of spheroidization3.3.81 石墨球数[球墨数] number of nodular graphites3.3.82 球化剂nodulizer， nodulizing alloy， spheroidal agent， spheroidizer 3.3.83 镁焦magcoke,impregnated coke3.3.84 型内球化in-mold nodularization3.3.85 密容加镁包sealed spheroidizing treatment ladle3.3.86 干扰元素interference element3.3.87 石墨蠕化处理[蠕化处理] vermiculation of graphite3.3.88 蠕化剂vermicular agent3.3.89 蠕化率percent of vermiculation3.3.90 铸铁净化purification of cast iron3.3.91 三角试块wedge test-piece3.4 铸造有色合金3.4.1 铸造有色合金〔铸造非铁合金〕nonferrous cast alloy3.4.2 铸造铝合金cast aluminum alloy3.4.3 高强度铸造铝合金high strength cast aluminum alloy3.4.4 铝硅合金aluminum-silicon alloy3.4.5 共晶铝硅合金eutectic aluminum-silicon alloy3.4.6 亚共晶铝硅合金hypoeutectic aluminum-silicon alloy3.4.7 过共晶铝硅合金hypereutectic aluminum-silicon alloy3.4.8 初生硅primary silicon phase3.4.9 共晶硅eutectic silicon phase3.4.10 铝镁合金aluminum-magnesium alloy3.4.11 铝铜合金aluminum-copper alloy3.4.12 铝锌合金aluminum-zinc alloy3.4.13 铝锂合金aluminum-lithium alloy3.4.14 铸造铜合金cast copper alloy3.4.15 铸造黄铜cast brass3.4.16 硅黄铜silicon brass3.4.17 高强度黄铜high strength brass3.4.18 青铜bronze3.4.19 锡青铜tin bronze3.4.20 铝青铜aluminum bronze3.4.21 铅青铜lead bronze3.4.22 硅青铜silicon bronze3.4.23 铸造铜铬合金[铬青铜] cast copper-chromium alloy3.4.24 高阻尼铜合金high damping copper alloy3.4.25 螺旋桨用铸造铜合金cast copper alloy for propeller3.4.26 铸造镁合金cast magnesium alloy3.4.27 铸造锌合金cast zinc alloy3.4.28 低熔点合金fusible alloys3.4.29 轴承合金[减摩合金] antifrictional alloys， bearing alloys3.4.30 巴氏合金babbitt metal ,white metal3.4.31 钛合金titanium alloy3.4.32 铸造高温合金3.4.33 镍基铸造高温合金3.4.34 蒙乃尔合金3.4.35 钴基铸造高温合金3.4.36 铁基铸造高温合金3.4.36 铁基铸造高温合金3.4.37 压铸合金3.4.38 压铸铝合金3.4.39 压铸镁合金3.4.40 压铸铜合金3.4.41 压铸锌合金3.4.42 锌当量3.5 熔炼基本术语3.5.1 熔炼3.5.2 熔化率3.5.3 熔炼损耗[熔损，烧损] 3.5.4 挥发损耗3.5.5 元素烧损3.5.6 元素增加3.5.7 熔池3.5.8 熔剂3.5.9 除气剂3.5.10 覆盖剂3.5.11 炉料3.5.12 金属炉料3.5.13 中间合金[母合金] 3.5.14 回炉料3.5.15 废金属料3.5.16 炉料计算[配料]3.5.17 熔渣[炉渣]3.5.18 沉渣3.5.19 浮渣3.5.20 碱性渣3.5.21 酸性渣3.5.22 造渣3.5.23 出渣3.5.24 出渣口3.5.25 炉衬3.5.26 碱性炉衬3.5.27 酸性炉衬3.5.28 耐火粘土3.5.29 碱度[碱性指数]3.5.30 补炉3.5.31 炉龄[炉衬寿命] cast superalloynickel-base cast superalloy Monel metalcobalt-base cast superalloy iron-base cast superalloyiron-base cast superalloy diecast alloyaluminium diecast alloy magnesium diecast alloy copper diecast alloyzinc diecast alloyzinc equivalentsmeltingmelting ratetotal melting loss volatilizing lossmelting loss of alloying element gain of elementbathfluxdegassing fluxcovering fluxchargemetallic chargemaster alloyfoundry returnsscrapcharge calculationslagsludgecinder， dross， scumbasic slagacid slagslag formingdeslaggingslag hole， slag notch furnace liningbasic liningacid liningfireclayindex of basicitypatchingfurnace campaign3.5.32 开炉blowing in， power on3.5.33 炉内气氛furnace atmosphere3.5.34 炉气分析flue gas analysis3.5.35 控制气氛controlled atmosphere3.5.36 炉前分析on-the-spot sample analysis3.5.37 出炉口tap hole3.5.38 出炉温度tapping temperature3.5.39 重熔remelting3.5.40 真空自耗电弧重熔consumable electrode vacuum arc refining3.5.41 喷射冶金injection metallurgy3.5.42 区域熔炼zone melting3.5.43 悬浮熔炼levitation melting， suspension melting3.5.44 真空熔炼vacuum melting3.5.45 坩埚炉crucible furnace3.5.46 坩埚crucible， pot3.5.47 保温炉holding furnace3.5.48 反射炉reverberatory furnace3.5.49 感应电炉electric induction furnace3.5.50 凝壳炉skull furnace3.5.51 增碳recarburizing3.5.52 增碳剂carburetant， carburetting agent， carburizer3.6 铸钢熔炼3.6.1 铸钢熔炼smelting of cast steel3.6.2 不氧化熔炼法dead melting3.6.3 氧化熔炼法oxidizing melting3.6.4 氧化期[沸腾期] oxidizing stage, boil stage3.6.5 氧化气氛oxidizing atmosphere3.6.6 氧化渣oxidizing slag3.6.7 还原期blocking stage， deoxidizing stage3.6.8 还原气氛reducing atmosphere3.6.9 还原渣reducing slag3.6.10 白渣white slag3.6.11 电弧炉electric arc furnace, direct electric arc furnace3.6.12 碱性电弧炉basic electric arc furnace3.6.13 酸性电弧炉acid electric arc furnace3.6.14 电渣熔炼electro-slag melting3.6.15 电渣炉electro-slag furnace3.6.16 氩氧脱碳法[AOD 法] AOD process， Argon-Oxygen Decarburization process 3.6.17 脱碳decarburization3.6.18 脱氧deoxidation3.6.19 脱氧剂deoxidizer3.6.20 脱磷dephosphorization3.6.21 脱硫desulphurization3.6.22 脱硫剂desulphurizer3.7 铸铁熔炼3.7.1 铸铁熔炼3.7.2 双联熔炼3.7.3 冲天炉3.7.4 大间距双排风口冲天炉smelting of cast ironduplexing smeltingcupolaspacious twin-tuyeres cupola， twin-wind blast system cupola3.7.5 多排小风口冲天炉multiple row small tuyeres cupola3.7.6 卡腰冲天炉waist shaped cupola3.7.7 热风冲天炉hot blast cupola3.7.8 水冷冲天炉water-cooled cupola3.7.9 水冷热风无炉衬冲天炉hot blast liningless cupola with water cooling3.7.10 无焦冲天炉cokeless cupola3.7.11 碱性冲天炉basic cupola3.7.12 酸性冲天炉acid cupola3.7.13 生铁pig iron3.7.14 铸造生铁foundry pig iron3.7.15 焦炭coke3.7.16 铸造焦炭[铸造焦] foundry coke3.7.17 固定碳fixed carbon3.7.18 铁焦比[焦比] iron coke ratio3.7.19 底焦coke bed3.7.20 层焦coke split3.7.21 隔焦extra coke3.7.22 接力焦buffer coke charge3.7.23 铁合金ferro-alloy3.7.24 有效高度effective height3.7.25 炉缸cupola well3.7.26 前炉forehearth3.7.27 密筋炉胆ribbed preheating jacket3.7.28 出铁槽cupola spout3.7.29 熔化带melting zone3.7.30 风带air belt， air box， wind box3.7.31 风口tuyere3.7.32 风口比tuyere ratio3.7.33 炉壁效应cupola wall effect3.7.34 冲天炉特性曲线cupola operation chart3.7.35 冲天炉炉前控制front control of molten iron of cupola， inspection in front of cupola 3.7.36 冲天炉检控仪tester and controller for cupola melting3.7.37 熔化强度melting intensity3.7.38 风量blast volume3.7.39 送风强度blast intensity3.7.40 送风压力blast pressure3.7.41 富氧送风oxygen enriched blast3.7.42 脱湿送风dehumidification blast3.7.43 预热送风hot blast3.7.44送风预热器blast preheater3.7.45火花捕集器spark arrestor3.7.46冲天炉加料机cupola charging machine3.7.47爬式加料机skip hoist3.7.48冲天炉自动加料机automatic cupola charging equipment3.7.49电磁盘electromagnetic chuck3.7.50电磁配铁秤electromagnetic weighing balancer3.7.51吸碳carbon pick-up3.7.52棚料[搭棚] bridging3.7.53封炉banking the cupola3.7.54打炉cupola drop3.7.55碎铁机breaker3.8金属液处理3.8.1精炼refining3.8.2真空精炼vacuum refining3.8.3炉外精炼ladle refining3.8.4精炼熔剂[精炼剂] refining flux3.8.5除气[去气] degassing3.8.6真空除气vacuum degassing3.8.7吹气净化blow purifying3.8.8多孔塞法porous plug process3.8.9变质modification3.8.10变质剂modification agent， modificator3.8.11磷变质phosphorus modification3.8.12钠变质sodium modification3.8.13长效变质剂permanent modificator3.8.14型内变质in-mold modification3.8.15孕育inoculation3.8.16瞬时孕育[后孕育] instantaneous inoculation， late stage inoculation， post inoculation 3.8.17随流孕育metal-stream inoculation3.8.18型内孕育in-mold inoculation3.8.19浇口盆孕育pouring basin inoculation3.8.20孕育剂inoculant， inoculating agent3.8.21孕育期inoculation period3.8.22孕育衰退inoculation fading3.8.23孕育不良abnormal inoculation， under-inoculation3.8.24合金化处理alloying treatment3.8.25喂线法[喂丝法] CQ process， wire feeding process， wire injection process3.8.26摇包shaking ladle3.8.27电磁搅拌electromagnetic agitation3.8.28静置holding， stewing3.8.29扒渣slagging-off3.8.30型内过滤in-mold filtering3.8.31型内合金化in-mold alloying3.8.32晶粒细化grain refinement3.8.33晶粒细化剂grain refiner3.9浇注3.9.1浇注pouring3.9.2保护气氛浇注pouring under controlled atmosphere 3.9.3真空浇注vacuum pouring3.9.4自动浇注装置automatic pouring device3.9.5自动浇注机automatic pouring machine3.9.6电磁浇注机electromagnetic pouring machine 3.9.7捣冒口churning，pumping3.9.8点冒口[补注] hot topping up，teeming3.9.9浇包ladle3.9.10底注包bottom pouring ladle3.9.11转运包transfer ladle3.9.12金属残液heel3.9.13冷金属cold metal3.9.14压铁weight4造型材料4.1基本术语4.1.1造型材料molding material4.1.2铸造用砂[砂] foundry sand，sand4.1.3原砂[新砂] base sand，new sand，raw sand 4.1.4旧砂used sand4.1.5回用砂reconditioned sand4.1.6再生砂reclaimed sand4.1.7枯砂[焦砂] burned sand4.1.8热砂hot sand4.1.9废砂waste sand4.2原砂4.2.1标准砂standard sand4.2.2硅砂[石英砂] silica sand4.2.3刚玉砂alumina sand4.2.3刚玉砂alumina sand4.2.4镁砂magnesite sand4.2.5锆砂zircon sand4.2.6镁橄榄石砂[橄榄石砂] fosterite sand，olivine sand4.2.7铬铁矿砂chromite sand4.2.8煤矸石砂coal gangue sand4.2.9熟料砂chamotte sand4.2.10炭粒砂carbon sand4.2.11石灰石砂limestone sand4.2.12天然砂natural sand4.2.13人工砂[人造砂] artificial sand4.2.14水洗砂washed-out sand4.2.15 擦洗砂scrubbed sand4.2.16 浮选砂[精选砂] floated sand4.2.17 松散密度(型砂) aerated density，riddled density4.2.18 原砂细度[AFS 平均细度] AFS fineness number，fineness number，grain fineness number 4.2.19 原砂粒度[原砂颗粒尺寸] particle size of base sand4.2.20 原砂颗粒分布grain size distribution of base sand4.2.21 原砂角形因数[原砂角形系数，原砂粒形系数] angularity of base sand4.2.22 原砂颗粒形状grain shape of base sand4.3 粘结剂4.3.1 粘结剂binder4.3.2 无机粘结剂inorganic binder4.3.3 粘土clay4.3.4 高岭土kaolin4.3.5 膨润土bentonite4.3.6 钠基膨润土sodium bentonite4.3.7 钙基膨润土calcium bentonite4.3.8 活化膨润土activated bentonite4.3.9 有机膨润土organic bentonite4.3.10 有效粘土effective clay4.3.11 活粘土active clay4.3.12 枯粘土[死粘土] burned clay4.3.13 白泥white clay4.3.14 水玻璃粘结剂sodium silicate binder，water glass binder4.3.15 水玻璃波美浓度Be concentration of water glass4.3.16 水玻璃模数sodium silicate modulus4.3.17 有机粘结剂organic binder4.3.18 纸浆废液[纸浆残液，亚硫酸盐纸浆废液] lignin liquor4.3.19 油类粘结剂oil based binder4.3.20 干性油drying oil4.3.21 合脂粘结剂synthetic fat binder4.3.22 渣油粘结剂residual oil binder4.3.23 自硬粘结剂[冷硬粘结剂] cold setting binder，no bake binder，self-hardening binder 4.3.24 树脂粘结剂resin binder4.3.25 热固性树脂粘结剂thermosetting resin binder4.3.26 热塑性树脂粘结剂thermoplastic resin binder4.3.27 铸造用树脂foundry resin4.3.28 自硬树脂系[非烘树脂系] no-bake resin system，self-hardening resin system4.3.29 气硬树脂系gas cured resin system4.3.30 热硬树脂系hot hardening resin system4.3.31 呋喃树脂furan resin4.3.32 酚醛树脂phenol-formaldehyde (PF) resin4.3.33 碱性酚醛树脂alkaline phenolic resin4.3.34 糠醇furfuryl-alcohol4.3.35 游离甲醛含量free formaldehyde content4.3.36 游离苯酚含量free phenol content4.3.37 粘结效率bonding efficiency4.4 辅助材料4.4.1 型砂附加物sand addlitives4.4.2 煤粉seacoal4.4.3 煤粉代用品seacoal substitutes4.4.4 铸型涂料dressing，mold coating，paint4.4.5 砂型涂料sand coating4.4.6 模样涂料pattern paint4.4.7 水基涂料water-base mold coating4.4.8 非水基涂料non-aqueous coating，non-aqueous paint4.4.9 自干涂料self-drying dressing4.4.10 摊开系数[铺展系数] spreading coefficient4.4.11 触变性thixotropy4.4.12 悬浮剂suspending agent4.4.13 分型剂parting agent4.4.14 脱模剂stripping agent4.4.15 固化剂[硬化剂] hardener4.4.16 有机酯organic ester4.4.17 溃散剂break-down accelerator，break-down agent4.4.18 发热剂exothermic mixture4.4.19 冒口覆盖剂riser cover4.4.20 补芯膏core mud4.5 型砂和芯砂4.5.1 型砂[造型混合料] molding mixture，molding sand4.5.2 芯砂core sand4.5.3 合成砂synthetic sand4.5.4 粘土砂clay-bonded sand4.5.5 天然型砂[天然粘土砂] natural molding sand，naturally clay-bonded sand 4.5.6 红砂red sand4.5.7 面砂facing sand4.5.8 背砂[填充砂] backing sand4.5.9 单一砂unit sand4.5.10 调匀砂temper sand4.5.11 湿型砂green molding sand，green sand4.5.12 煤粉砂black sand4.5.13 烂泥砂[麻泥] loam4.5.14 油砂oil-bonded sand4.5.15 合脂砂synthetic fatty acid bonded sand4.5.16 石墨型砂graphite mold sand4.5.17 化学硬化砂chemical hardening sand4.5.18 自硬砂self-hardening sand，no-bake sand4.5.19 水泥砂cement sand4.5.20 水玻璃砂sodium silicate-bonded sand4.5.21 酯硬水玻璃砂ester cured sodium silicate sand，sodium silicate－ester no-bake sand 4.5.22 树脂自硬砂no-bake resin sand，self-hardening resin sand4.5.23 呋喃树脂自硬砂no-bake furan resin sand4.5.24 酚醛尿烷树脂自硬砂pep-set no-bake sand，phenolic urethane no-bake sand4.5.25 酯固化碱性酚醛树脂自硬砂ester cured alkaline phenolic resin no-bake sand4.5.26 磷酸盐自硬砂phosphate no-bake sand4.5.27 流态砂castable sand，fluid sand4.5.28 气硬砂[冷芯盒砂] cold box sand，gas hardening sand4.5.29 热硬树脂砂hot hardening resin sand4.5.30 覆膜砂precoated sand，resin coated sand4.5.31 壳型(芯)树脂砂shell mold (core) resin sand4.5.32 热芯盒砂hot box sand4.5.33 结球(型砂) agglomeration (molding sand)4.6 型砂性能及试验4.6.1 型砂试验sand testing4.6.2 原砂试验base sand testing4.6.3 型砂试样sand specimen4.6.4 型砂膨胀试验sand expansion testing4.6.5 型砂高温试验elevated temperature testing of sands4.6.6 差热分析differential thermal analysis4.6.7 型砂试验仪sand tester4.6.8 铸造用标准筛standard sieves for foundry4.6.9 筛析screen analysis4.6.10 沉降分选decantation，elutriation4.6.11 型砂强度sand strength4.6.12 湿强度green strength4.6.13 干强度dry strength4.6.14 热强度hot strength4.6.15 热湿拉强度hot wet tensile strength4.6.16 风干强度air dried strength4.6.17 型砂韧性toughness4.6.18 破碎指数shatter index4.6.19 起模性liftability4.6.20 表面安定性surface stability index(SSI)4.6.21 残留强度retained strength4.6.22 溃散性collapsibility4.6.23 落砂性knockout capability4.6.24 砂型(芯)硬度mold hardness4.6.25 紧实度degree of ramming4.6.26 紧实率compactability4.6.27 舂实性rammability4.6.28 流动性(砂) flowability (sand)4.6.29 成型性moldability4.6.30 孔隙率porosity4.6.31 透气性permeability4.6.32 发气量[发气性] gas evolution4.6.33 发气率[发气速度] gas evolution rate4.6.34 退让性[容让性] deformability，yieldability4.6.35 热变形(型砂) hot deformation (mold sand)4.6.36 吸湿性moisture absorption4.6.37 粘模性stickiness4.6.38 保存性(型砂) preservability (mold sand)4.6.39 可使用时间bench life，working time4.6.40 型砂耐火度refractoriness of molding sand4.6.41 微粉含量micro-grains content4.6.42 含泥量clay content4.6.43 含水量[水分] moisture content4.6.44 型砂酸碱度值[型砂pH 值] pH value of sand4.6.45 酸耗值acid demand value4.6.47 型砂缺陷倾向defect tendency of molding sand4.6.48 胶质价colloid index4.6.49 膨润值swelling value4.6.50 膨胀指数swelling index4.6.51 吸蓝量试验methylene blue value test4.6.52 有效膨润土量effective bentonite content4.6.53 耐用性[复用性] durability4.6.54 涂刷性brushability4.6.55 覆膜砂熔点melting point of precoated sand5 铸造工艺设计及工艺装备5.1 基本术语5.1.1 铸造性能castability5.1.2 流动性(金属) fluidity (metal)5.1.3 充型能力mold-filling capacity5.1.4 充型流速[浇注速度] delivery rate，pouring rate5.1.5 充型时间filling time5.1.6 浇注温度pouring temperature5.1.7 比浇注速度specific pouring rate5.1.8 浇注时间pouring time5.1.9 平衡分配系数equilibrium distribution，equilibrium partition ratio5.1.10 凝固solidification5.1.11 凝固温度范围solidification range5.1.12 凝固时间solidification time5.1.13 均衡凝固proportional solidification5.1.14 同时凝固simultaneous solidification5.1.15 顺序凝固[方向凝固] directional solidification5.1.16 无溶质再分配凝固[无偏析凝固] partitionless solidification，segregationless solidification 5.1.17 收缩contraction5.1.18 液态收缩liquid contraction5.1.19 凝固收缩solidification contraction5.1.20 固态收缩solid contraction5.1.21 液- 固收缩liquid-solid contraction5.1.22 自由收缩free contraction5.1.23 受阻收缩hindered contraction5.1.24 收缩余量shrinkage allowance5.1.25 缩前膨胀[共晶石墨化膨胀] eutectic graphitizing expansion5.1.26 收缩应力contraction stress5.1.27 热应力thermal stress5.1.28 相变应力phase change stress，transformation stress5.1.29 铸造应力casting stress5.1.30 残留应力[残余应力] residual stress5.1.31 合金线收缩率[自由线收缩率] alloy linear contraction coefficient，free linear contraction5.1.32 铸件线收缩率casting linear contraction coefficient，casting linear shirinkage coeffic-5.1.33 热裂倾向性tendency to hot tearing5.2 铸造工艺设计5.2.1 铸造工艺设计casting process design5.2.2 铸造工艺计算机辅助设计[铸造工艺CAD] computer-aided design of the casting process, casting 5.2.3 实体造型constructive solid geometry，solid modeling5.2.4 充型分析mold filling analysis5.2.5 铸造工艺装备设计foundry tools design5.2.6 铸造工艺图foundry molding drawing5.2.7 铸造工艺卡foundry process card5.2.8 铸型装配图mold assembly drawing5.2.9 铸件图[毛坯图] drawing of rough casting5.2.10 铸造工艺准备preparation for casting technique5.2.11 铸件设计casting design5.2.12 铸件基准面reference face for machining of casting5.2.13 铸合结构cast fabricated constructure5.2.14 分型面mold joint，mold parting，parting face5.2.15 不平分型面irregular joint，irregular parting，match parting5.2.16 阶梯分型面stepped joint，stepped parting5.2.17 过渡角transition angle5.2.18 分型负数joint allowance，parting allowance5.2.19 浇注位置pouring position5.2.20 工艺补正量design modification，molding allowance5.2.21 吃砂量mold thickness5.2.22 补贴pad5.2.23 交接壁intersection5.2.24 十字交接[X 形交接] X-junction5.2.25 内圆角[圆角] fillet5.2.26 热节hot spot5.2.27 铸筋[铸肋] ribs5.2.28 加强筋[加强肋] stiffening ribs5.2.29 5.2.30 5.2.31 5.2.32 5.2.33 5.2.34 5.2.35 5.2.36 5.2.37 5.2.38 5.2.39 5.2.40 5.2.41 5.2.42 5.2.43 5.2.44 5.2.45 5.2.46 5.2.47 5.2.48 5.2.49 5.2.50 5.2.51 5.2.51 5.3 5.3.1 5.3.2 5.3.3 5.3.4 5.3.5 5.3.6 5.3.7 5.3.8 5.3.9 5.3.10 5.3.11 5.3.12 5.3.13 5.3.14 5.3.15 5.3.16 5.3.17 5.3.18 5.3.19冷铁外冷铁内冷铁暗冷铁强制冷却起模斜度上型[上箱]下型[下箱]型冷时间型腔造型余量砂芯设计芯头芯头间隙芯头斜度芯座定位芯头加大芯头工艺孔铸件凝固数值模拟前处理潜热处理网格剖分网格剖分浇冒口系统浇注系统浇注系统设计浇道比封闭式浇注系统半封闭式浇注系统开放式浇注系统阶梯式浇注系统缝隙式浇注系统离心集渣浇注系统阻流浇注系统冒口浇注系统顶注式浇注系统雨淋式浇注系统底注式浇注系统中注式浇注系统垂直浇注系统等流量浇注系统阻流截面大孔出流densener, chillsurface densenerinternal densenercoated chill， indirect chillforced coolingpattern draftcope， top partbottom part， dragmold cooling timemold cavitymolding allowancesand core designcore printcore print clearancecore tapercore seatlocating printenlarged core print， strengthened core printtechnological holenumerical simulation of casting solidificationpre-processinglatent heat treatmentenmeshment， mesh generationenmeshment， mesh generationgating system， running systemdesign of gating systemgating ratiochoked running system， pressurized gating systemenlarged runner systemnon-pressurized gating system， unchoked running systemstep gating systemslot gate systemwhirl gate dirt trap systemchocked runner systemfeeder head gating， riser gatingtop gating systemshower gate systembottom gating systemparting-line gating systemvertical gate systemequal-volume pressurized gating system， flow-rate equalized gatingchoked arealarge orifice discharge5.3.20 浇口盆[外浇口] pouring basin5.3.21 浇口塞blanking-off plug5.3.22 浇口杯pouring cup5.3.23 直浇道sprue5.3.24 直浇道窝sprue base5.3.25 横浇道runner5.3.26 集渣横浇道skim runner5.3.27 集渣装置(浇注系统) dirt traps (in gating system)5.3.28 反应室(浇注系统) reaction chamber (in gating system) 5.3.29 内浇道ingate5.3.30 压边浇口lip runner， kiss runner5.3.31 牛角浇口horn gate5.3.32 挡渣片baffle core5.3.33 过滤片[过滤网] filter screen， strainer core5.3.34 冒口riser， feeder head5.3.35 明冒口open riser5.3.36 暗冒口blind riser5.3.37 侧冒口side riser5.3.38 热冒口hot riser， hot top5.3.39 保温冒口insulating riser5.3.40 发热冒口exothermic riser5.3.41 电热冒口electric arc feed5.3.42 压力冒口pressure riser5.3.43 发气压力冒口gas-delivered pressure riser5.3.44 大气压力冒口atmospheric riser5.3.45 易割冒口knock-off head5.3.46 离心集渣冒口whirl-gate riser5.3.47 冷冒口cold riser5.3.48 出气冒口[出气口] flow off， pop off， riser vent， whistler 5.3.49 冒口设计riser design5.3.50 内接圆法inscribed circle method5.3.51 模数计算法(冒口) moduli calculation method5.3.52 周界商perimetrischen quotient5.3.53 冒口效率riser efficiency5.3.54 补缩feeding5.3.55 有效补缩距离effective feeding distance， feeding zone 5.3.56 补缩通道feeding channel5.3.57 反补缩inverse feeding5.3.58 冒口根riser pad5.3.59 冒口颈riser neck5.3.60 冒口圈feeder bush， riser bush5.3.61 冒口套heat insulating feeder sleeve5.3.62 冒口窝riser base5.3.63 冒口高度riser height5.3.64易割片knockoff core， washburn core5.4铸造工艺装备5.4.1铸造工艺装备foundry tools equipment5.4.2模板pattern plate5.4.3组合模板composite pattern plate5.4.4双面模板match plate5.4.5单面模板single face pattern plate5.4.6模板图pattern plate drawing5.4.7模板设计pattern plate design5.4.8缩尺[模样工放尺] pattern-maker rule， shrinkage rule 5.4.9放样[伸图] hot dimensional drawing， layout 5.4.10模底板pattern mounting plate5.4.11模样[铸模、模] pattern5.4.12祖模grand master pattern5.4.13母模master pattern5.4.14金属模metal pattern5.4.15木模wooden pattern5.4.16石膏模plaster pattern5.4.17塑料模plastic pattern5.4.18骨架模skeleton pattern5.4.19单体模loose pattern5.4.20整体模one-piece pattern， solid pattern 5.4.21分块模[分开模] loose pattern， split pattern5.4.22分模面parting line5.4.23模样分级pattern classification5.4.24活块loose piece5.4.25砂箱flask, molding box5.4.26组合砂箱built up molding box5.4.27砂箱设计flask design5.4.28套箱mold jacket5.4.29套销hollow pin， stub pin5.4.30箱带[箱挡] cross bar， flask bar5.4.31芯盒core box5.4.32芯盒设计core box design5.4.33芯盒图core box drawing5.4.33芯盒图core box drawing5.4.34对开芯盒half core box5.4.35脱落式芯盒troughed core box5.4.36分盒面parting of core box6砂型铸造6.1砂处理6.1.1型砂制备[砂处理] sand preparation6.1.2型砂质量控制sand quality control6.1.3型砂水分控制装置automatic moisture controller of sand6.1.4旧砂处理sand reconditioning6.1.5旧砂再生sand reclamation6.1.6旧砂热法再生thermal reclamation of used sand6.1.7旧砂湿法再生wet reclamation of used sand6.1.8旧砂干法再生dry reclamation of used sand6.1.9旧砂回用率reusable rate of used sand6.1.10砂冷却sand cooling6.1.11热砂冷却装置hot sand cooler6.1.12砂温调节器sand temperature modulator6.1.13冷却提升机coolelevator， cooling elevator6.1.14热气流烘砂装置hot pneumatic tube drier6.1.15沸腾床fluidized bed6.1.16滚筒筛rotary screen,drum screen6.1.17磁力滚筒magnetic separator6.1.18滚筒破碎筛drum breaking screen6.1.19筛砂机riddle6.1.20原砂擦洗机sand scrubber6.1.21轮碾机roller6.1.22配砂formulation of sand mixture6.1.23预混premixing6.1.24混砂sand mixing， sand mulling6.1.25混砂机sand mixer， sand muller6.1.26连续混砂机continuous sand mixer6.1.27碗形混砂机cup-type sand mixer6.1.28树脂自硬砂混砂机no-bake resin sand mixer6.1.29松砂aeration， sand-cutting6.1.30松砂机aerator， sand cutter6.1.31回性[调匀] (型砂) homogenization of sand， temper of molding sand 6.1.32除尘器dust catcher， dust collector6.2造型6.2.1造型molding6.2.2有箱造型flask molding6.2.3无箱造型flaskless molding6.2.4手工造型hand molding6.2.5机器造型machine molding6.2.6地坑造型pit molding6.2.7地面造型floor molding6.2.8叠箱造型stack molding6.2.9多箱造型multiple-part molding6.2.10两箱造型two -part molding6.2.11假箱造型oddside molding6.2.12劈箱造型split box molding6.2.13脱箱造型removable flask molding6.2.14刮板造型sweep molding。
铸造行业英语词汇大全
铸造行业英语词汇大全：一、铸造基本术语1. Casting：铸件2. Pattern：模样3. Mold：模具4. Core：砂芯5. Sand：砂子6. Foundry：铸造厂7. Melting：熔炼8. Pouring：浇注9. Solidification：凝固10. Casting Defects：铸件缺陷11. Machining：机械加工12. Inspection：检验二、铸造材料1. Grey Cast Iron：灰铸铁2. Ductile Cast Iron：球墨铸铁3. White Cast Iron：白铸铁4. Highstrength Cast Iron：高强度铸铁5. Stainless Cast Steel：不锈钢铸件6. Carbon Steel：碳钢7. Alloy Steel：合金钢8. Titanium Alloy：钛合金9. Aluminum Alloy：铝合金10. Copper Alloy：铜合金11. Magnesium Alloy：镁合金三、铸造工艺1. Sand Casting：砂型铸造2. Investment Casting：熔模铸造3. Die Casting：压铸4. Centrifugal Casting：离心铸造5. Continuous Casting：连续铸造6. Squeeze Casting：挤压铸造7. Lost Foam Casting：消失模铸造8. Shell Mold Casting：壳型铸造9. Vprocess Casting：V法铸造10. Highpressure Die Casting：高压铸造四、铸造设备1. Melting Furnace：熔炼炉2. Pouring Machine：浇注机3. Sand Mixer：砂混合机4. Molding Machine：造型机5. Core Shooter：射芯机6. Shakeout Machine：落砂机7. Grinding Machine：磨削机8. Shot Blasting Machine：喷砂机9. Testing Equipment：检测设备10. Robot：机器人五、铸造缺陷1. Blowhole：气孔2. Sand inclusion：砂眼3. Porosity：缩孔4. Shrinkage：缩松5. Cold shut：冷隔6. Hot tear：热裂7. Overfeed：过补给8. Underfeed：欠补给9. Oxidation：氧化10. Incomplete fusion：熔接不良六、铸造技术参数1. Tolerance：公差2. Draft：拔模斜度3. Parting Line：分模线4. Riser：冒口5. Gate：浇道6. Runner：滑道7. Cooling Time：冷却时间8. Solidification Time：凝固时间9. Molding Sand Properties：型砂性能10. Core Sand Properties：芯砂性能七、环保与安全1. Environmental Protection：环保2. Waste Gas Treatment：废气处理3. Waste Water Treatment：废水处理4. Solid Waste Treatment：固体废物处理5. Dust Collection：除尘6. Safety：安全7. Personal Protective Equipment：个人防护装备8. Fire Protection：消防9. Occupational Health：职业健康10. Accident Prevention：事故预防八、国际合作与标准1. ISO：国际标准化组织2. ASTM：美国材料与试验协会3. DIN：德国工业标准4. JIS：日本工业标准5. BS：英国标准6. SAE：美国汽车工程师协会7. International Foundry Research：国际铸造研究8. Foundry Technology Transfer：铸造技术转移9. Import and Export：进出口10. Global Foundry Industry：全球铸造行业。
铸造术语 中英文对照
一、基本术语1.铸造：casting ，founding , foundry2。
砂型铸造: Sand casting process3.特种铸造：Special casting process4.铸件：casting5。
毛坯铸件：Rough casting6.砂型铸件：Sand casting7.试制铸件：Pilot casting8。
铸态铸件：as—cast casting9.铸型[型］：mold10.铸造工艺：Casting process, foundry technology11。
铸造用材料：Foundry materials12.铸造工艺材料：Consumable materials13。
铸造设备：Foundry equipment, foundry facilities14.铸工: Caster，founder，foundry worker15.铸造工作者：foundryman16。
铸造车间: Foundry shop17.铸造厂：Foundry18。
铸造分厂：Attached foundry，captive foundry，tied foundry 19。
铸造三废：Foundry affluent20。
一批： A batch21。
一炉： A cast，a heat，a melt22。
铸焊: Cast welding，flow welding23。
铸锭：ingot二、铸造合金及熔炼、浇注2。
1铸造合金基础术语1.铸造合金：Cast alloy2。
共晶合金系：Eutectic alloy system3.共晶合金：Eutectic alloy4.亚共晶合金：Hypoeutectic alloy5.过共晶合金: Hypereutectic alloy6.共晶团：Eutectic cell7.共晶温度: Eutectic temperature8.共晶转变：Eutectic reaction，eutectic transformation9.共晶组织：Eutectic structure10.铸造复合材料：Cast composite11.定向共晶复合材料: Directional eutectic composite12。
铸造学专业英语词汇
铸造学专业英语词汇底浇铸模bottom pour mold底进模口法bottom gating底面basal plane底炭bed coke底炭高度bed coke height底特律式电弧炉Detroit electric furnace地坑pit地坑炉pit furnace地坑造模法pit molding地坑铸造pit casting地面砂，背砂floor sand地模floor mold地模法，地面造模法floor molding碲(Te) tellurium碘(I) iodine点火firing点火ignition点火ligh up点火lighting up点火light-off点火孔breast door点火孔lighting hole点火器igniter点燃点ignition point电池，组battery电磁搅拌electric magnetic agitation电磁循环electric magnetic circulation电动吊车electric hoist电动发电机motor generator电动加气硬化机automatic gassing machine 电动推高机electric lift truck电动造模机electric molding machine电镀electro-gilding电镀electro-plating电焊条，电熔接条arc welding electrode电弧长度arc length电弧截割arc cutting电弧炉arc furnace电弧炉electric arc furance电弧气吹铲平arc-air gouging电弧气吹切割arc-air cutting电弧熔接arc welding电弧熔接，电焊electric arc welding电极，电熔接条，电焊条electrode电极耗用量(电弧炉) electrode consumption电极夹具，电熔接条夹把，电焊条夹把electrode holder 电极控制系统electrode control system电极清洁法electrol-cleaning电极熔接，电极焊接electrode welding电极头stub end电解精炼electrolytic refining电解铁electrolytic iron电解铜electrolytic copper电解锌electroplytic zinc电开关装置electric switchgear电炼生铁electric furance iron电炉electric furance电炉钢electric steel电滤尘器electro-filter电木，胶木bakelite电热熔化electric smelting电子electron电子显微镜electron microscope电阻高温计resistance pyrometer电阻合金electro-resistance alloy电阻炉electric resistance furance电阻炉resistance furnace电阻系数，电阻力resistivity垫板，底板base plate垫厚(铸造技术) padding，reinforcement垫厚(铸造技术) reinforcement，paddling垫圈，洗涤机washer淀粉starch吊车hoist吊车浇桶crane ladle吊车盘hoist pan吊钩lifting hook吊骨，撑条，插条gagger吊骨，撑条，插条slodier吊骨，吊具，吊架hanger吊环bail吊梁lifting beam吊砂条clack吊运车trolley吊钩load hook吊骨anchoring调合模砂blended molding sand调节设备controlled means调辙车transfer car调整器regulator调质处理quenching with Subsequent tempering 调质砂tempering sand调质水分tempering water调质铸铁modified cast iron蝶形阀butterfly valve迭边浇道Connor runner bar迭边进模口kiss gate迭边进模口lap gate迭边冒口kiss riser迭模multiple mold迭模stack boxes迭模stack mold迭模法multiple molding迭模法stack molding迭模浇铸法stack pouring迭箱stack钉nail顶板ejection plate顶板lifting plate顶板top board顶板top plate顶出ejection顶出板(压铸) ejector plate顶出杆knock-out bar顶出力ejector force顶出器，喷射器ejector顶出销knock-out pin顶出销(压铸) ejector顶浇法top pouring顶浇进模口top gate顶冒口top riser顶销，起销lifting pin顶铸法top casting process定量分析quantitative analysis定量仪quantometer定模(压铸) cover die定模板(压铸)，平台platen定盘式混砂机fixed pan mill定时淬火time quenching定时器timer定位垫locating pad定位孔locating hole定位销locating pin定位销钉positioning dowel定位锥locating cones定心毂centering boss定心针centering pin定性分析qualitative analysis订货铸造工场jobbing foundry铥(TM) thulium冻汞法(精密铸造) Mercast process动力滚子输送机powered roller conveyor 动力试验dynamic test动叶轮impeller动叶轮摔砂impeller ramming动作，工作working都市煤气town gas陡震试验shock test斗，箕斗，桶装载机bucket毒性度toxicity rating读数式分光仪digital spectrometer堵口砖nozzle brick堵塞bott堵塞botting堵塞出铁口(熔铁炉) stopping up堵塞杆bott stick堵塞器stopper堵塞式浇桶stopper ladle堵塞砖stopper and nozzle brick杜具纳转炉Tropenas converter杜维利化碳转浇铸法Durville pouring杜维利化碳转浇铸法Durville process镀镍nickel plating镀锡铁皮，马口铁皮tin plate镀锌galvanizing镀锌sherardizing镀锌zinc coating镀锌zinc plating镀锌，浸锌zinc galvanizing镀锌脆性galvanizing embrittlement镀锌铁板，白铁皮galvanized iron sheet 镀锌铁皮，白铁皮zinc-coated sheet短暂退火炉short anneal furnace锻造用合金wrought alloy断口检验fracture test断口金相检验fractography断裂点point of rupture断面收缩necking断面缩率area contraction，percentage of断面缩率area reduction，percentage of断续浇铸interrupted pouring堆heap堆高机fork lift truck堆积密度packing density堆料场stock ground堆料场stock-yard堆砂heap sand堆渣场slag tip堆重piled weight对合开放砂心盒split open ended core box对合模型，分割模型split pattern对合模型板，分割模型板split plate对合铸模split mold对流convection对准alignment钝气inert gas钝气电弧熔接inert-gas arc welding多边形筛polygonal screen多段风口，多段风嘴multiple tuyere多角形砂angular sand多孔塞porous plug多孔塞搅拌法porous-plug method多孔性，气孔率，气孔巢(铸疵) porosity多石英砂quartzose sand多水高岭土halloysite锇(Os) osmium鹅颈浇道，鹅颈管goose neck而酸铸铁acid resistant cast iron耳轴，挂耳trunnion二次风口，二次风嘴secondary tuyere二次合金secondary alloy二次空气secondary air二钙硬化法Di-Cal process二氧化锆zirconia二氧化碳造模法，碳酸气硬模法，CO2造模法carbon dioxide process(CO2 process) 二氧化铁(FeO2) ferrous oxide二元合金binary alloy发火合金pyrophoric alloys发热反应exothermic reaction发热覆盖?冒口用) exothermic shield发热冒口exothermic riser发热套筒exothermic sleeve发热性缩颈砂心(冒口用) exothermic breaker core 发热性缩孔防止粉exothermic antipiping powder 发生炉producer发生炉煤气power gas发生炉煤气producer gas发生炉燃气，瓦斯generator gas阀valve珐琅面，上釉glassy surface翻举装置rollover and lifting device翻模rolling over翻模板rollover board翻模板rollover plate翻箱索具beam and sling翻箱造模机rollover molding machine翻转(壳模制造) peel back翻转，翻模rollover翻转顶销脱模机turnover and pinlift machine翻转式砂心机rockover core making machine翻转脱模式造模机frame-rollover machine翻转脱模装置turn-draw device翻转造模机turnover molding machine钒(V) vanadium钒铁ferro-vanadium钒铸铁vanadium cast iron反复冲击试验repair反复横断冲击试验repeated impact test反喇叭形浇口reverse horn gate反射炉air furnace反射炉reverberatory furnace反跳硬度计scleroscope反跳硬度试验rebound hardness test反跳硬度试验scleroscope hardness test反斜度back draft反应带reaction zone反应度reactivity反应模斜度inverse draft反应速率rate of reaction反转起模draw on turnover方锉square file方解石calcite方向性凝固directional solidification防尘面具，口罩respirator防护套管protection tube防裂筋cracking strip防裂片，散热片cooling fin防蚀anti-corrosion防缩暗冒口shrink bob防缩剂，冒口保温用anti-piping compound防缩孔粉剂pipe eliminator防缩冒口shrink head防缩冒口shrinker防锈anti-rust防锈剂rust-preventing agent防锈涂层rust preventive coating放射线检验radiographic inspection放射线检验radiographic testing放射线透视radioscopy放射线照片radiographic film放射线照像术radiography放射性同位素radioactive isotope放样板lay out board放置器set-down device非磁性铸铁non-magnetic cast iron非焦性煤non-coking coal非金属夹杂物non-metallic inclusion非金属夹杂物sonims非均质组织heterogeneous structure非破坏试验non-destructive testing(NDT)非铁金属non-ferrous metal非氧化气孔(银白色气孔)(铸疵) unoxidized blowholes 飞边(铸件) feather飞边，闪光flash飞边清除flash removal飞边现象(合模或模裂形成) finning飞灰fluxing肥粒铁，肥粒体ferrite肥粒铸铁ferritic cast iron沸腾boil沸腾boiling沸腾期boiling period费德曼组织(金相) Widmannstaetten structure废(钢)片sheet scrap废电极electrode scrap废钢scrap steel废料scrap废品率arate of rejects废品率，退件率，不良率reject ratio废品率，退件率，不良率rejection rate，reject atio 废气exhaust gas废气waste gas废热waste heat废铁iron scrap废铁scrap iron废铸料cast scrap分布distribution分部模型section pattern分部心型sectional core分层浇口side step gating分层进模口side step gate分层精炼法zone refining分次式混合机batch mixer分次式火炉batch type annealing furnace分次式磨粉机batch mill分次式配砂场batch sand plant分次式熔炉batch furnace，batch-type furnace)分次退火炉periodic annealing furnace分道砖runner core分度盘dividing plate分度圈limb分段淬火interrupted quenching分段淬火stage hardening分段淬火step quenching分段时效interrupted aging分段退火stepped annealing分级，刻度graduation分级节(模砂) classifying screen分级进模口steeped sprue分级进模口step gate分级进模口stepped side gate分级进模口铸造step gate casting分级筛grading screen分级筛size screen分级摇动筛size jigging screen分级硬度gradient hardness分件图parts drawing分解resolution分离器separator分离筛sepaating screen分离型波来铁(球状云明碳机) divorced pearlite 分模粉parting powder分模剂parting agent分模剂parting compound分模面mold joint分模面parting surface分模面进模口parting gate分模砂parting sand分模线parting line分模纸parting paper分配流槽distributing launder分配销(压铸) sprue pin分支砂心，分支心模branch core分铸试验separately cast test bar分子molecule酚phenol酚<<an017>>喃树脂phenolic furan resin酚甲醛树脂phenol-formaldehyde resin酚树脂phenolic resin酚塑，黏结剂phenol plast binder粉煤powdered coal粉煤pulverized coal粉煤装置powdeed coal equipment粉末金属powdered metal粉末金属机件powdered metal parts粉末冶金，粉末冶金术powder metallurgy粉状石墨plumbago封闭sealing封闭剂sealing compound封闭砂条sealing ring封罐退火pot annealing封合模型，分割模型parted pattern封盒退火box annealing封漏，浸入impregnation风锤air hammer风管输送机pneumatic tube conveyer风管输送系统penumatic tube dispatch system 风化石锥辗硅砂conical sand from stone风口，风嘴tuyere风口棒tuyere bar风口比tuyere ratio风口带tuyere zone风口面buyere line风力分级air classification风力净化法air cleaning process风量，体积air volume风量计air volume meter风量计blast volume meter风量控制仪air weight controller风干air drying风干法air seasoning风干强度air strength风干强度air-dried strength风扇fan风速计anemometer风箱air belt风箱air box风箱air tank风箱wind belt风箱wind box风硬air hardening风硬钢air-hardening steel枫木maple蜂巢炉beehive oven蜂巢炉焦炭beehive coke蜂蜡bees wax伏利安[气体]搅拌法voianik method氟(F) fluorine浮渣dross浮渣incrustation浮渣，夹渣scum浮渣，撇渣skim幅射高温计radiation pyrometer幅射管炉radiant tube furnace复合辊composite roll复合接种剂complex inoculant复合涂膜complex coating复合形砂compound sand复合铸造composite casting复磷repetition castings复热器recuperator复热系统recuperative system复置模型试模replacing pattern in the mold 复制品replica腐蚀corrosion腐蚀脆化corrosion embrittlement附件accessories附浇口系模型gated pattern附设铸工场capitive foundry附设铸工场tied foundry附体试杆cast-on bar附体试杆cast-on test bar附体试片test coupon附体试片test lug附体试验attached test coupon负偏析negative segregation负载load副产焦炭by-product coke副电流sedondary current副料indirect materials副线圈secondary coil腹板web覆盖热cover heating折心展性铸铁iron oxide covering覆盖层[熔剂], 涂层covering flux钆(Cd)(烯土金属) gadolinium改良合金modified alloy钙(Ca) calcium钙系膨土calcium bentonite灰汁，碱水lye盖M法，疏塞气体搅拌法Gazal process 甘油glycerine坩埚crucible坩埚底座，垫砖stool坩埚式感应电炉coreless induction furance 坩蜗吊钳crucible lifter坩蜗法crucible process坩蜗钢crucible steel坩蜗浇铸装置crucible pouring device坩蜗炉crucible furnace坩蜗钳crucible tongs坩蜗涂浆crucible wash杆，棒，条bar杆盘松砂机spike disintegrator杆条矫直机rod straightener感应淬火induction quenching感应电炉electric induction furnace感应电炉induction furnace感应加热induction heating感应器inductor感应线圈induction coil感应硬化induction hardening橄榄石砂oliving sand刚铝，杜拉铝duralumin刚铝石alundum刚模半边(压铸) die half，die cast刚模钢die steel刚模试验(压铸) die try-out，die cast刚模穴(压铸模) die cavity刚砂emery刚性rigidity刚玉corundum纲丝netting wire纲状组织(金相) net-work structure钢steel钢厂steel works钢锭steel ingot钢坩埚steel crucible钢皮镁砖metal-case magnesite brick钢输送带steel conveyor belt钢水瓢，抹砂匙spoon钢水瓢测温法spoon test钢丝钳pliers钢丝刷wire brush钢丝索wire rope钢丝位wire cut钢条bar steel钢条steel bar钢线粒cut wire shot钢屑，废钢料steel scrap钢性铸铁semi-steel钢铸件steel castings高傲砂blended sand高级钢high-grade steel高级铸铁high class cast iron高级铸铁high grade cast iron高加波感应电炉，高频率感应电炉high frequency induction furance 高架磁选机overhead magnetic seperator高架单轨overhead monorail高架起重机gantry crane高拉力黄铜high tensile brast高拉力铸铁，高强度铸铁high tension cast iron高磷生铁high phosphorus pig iron高磷生铁phosphoric pig iron高岭石kaolinite高岭土kaolin高硫钢(易切钢之一种) sulphur steel高炉shaft furnace高炉，鼓风炉blast furnace高炉焦furnace coke高炉煤焦，鼓风煤焦blast furnace coke高铝红柱石mullite高锰钢Hadfield's manganese steel高锰钢铸件high manganese steel castings高黏土砂fat sand高黏土铸砂loamy sand高强度钢，高拉力钢high tension steel高强度黄铜high strength brass高强度铸铁high strength cast iron高碳钢high carbon steel高温淬火hot quenching高温计pyrometer高温耐火砖highly refractory brick高温强度(铸砂用) hot strength高温烧结high sintering高温试验hot test高温冶金学pyrometallurgy高硅生铁silvery iron高硅砖high siliceous brick高压罐bomb高压水清砂机hydro-blast高压造模法high pressure molding高氧化铝砖high-alumina brick高氧砖alumina brick高硬度钢glass hard steel高周波干燥，高频率干燥dielectric dry高周波干燥机，高频率干燥机dielectric dryer高周波砂心干燥炉hign-frequency core drying stove 搞压试验compression test锆(Zr) zirconium锆砂zircon sand锆石粉zircon flour锆英石zircon格子(结晶) lattice格子结构lattice structure格子筛分输送机grid type screening conveyor格子形耐火砖checker brick隔条砂箱barred box镉(Cd) cadmium铬(Cr) chromium铬钢chrome steel铬基耐火材料chrome base refractories铬克合金nichrome铬镁砂chrome-magnesite铬砂chromite sand铬砂hevi sand铬酸处理chrome pickle treatment铬酸处理(镁锌铸件镀铬) dichromate treatment 铬铁ferro-chromium铬铁矿chromite铬铸铁chrome cast iron铬砖chromite brick给砂机sand expansion工地熔接site weld工具tool工具钢tool steel工具台tool table工模jig工资labor cost工作场所working aea工作大纲图表outline process chart工作路线排定rounding工作台working table工作图，制造图working drawing弓锯hack saw弓锯机hack-sawing machine公差tolerance公忽micron(u)汞(水银)(Hg) mercury拱arch拱砖arch brick共晶eutectic共晶点eutectic point共晶反应eutectic peaction共晶合金eutectic alloy共晶石墨eutectic graphite共晶温度eutectic temperature共晶细胞eutectic cell共晶细胞数eutectic cell count共晶雪明碳铁eutectic cementite共晶铸铁eutectic cast iron共晶组织eutectic structure共析eutectoid共析反应eutectoid reaction共析钢eutectoid steel共析组织eutectoid structure钩hook购入废料purchused scrap股strand骨架模型skeleton pattern钴60，钴六十cobalt 60鼓风blast鼓风，喷风air blast鼓风调节器blast regulator鼓风管blast pipe鼓风机blower鼓风计blast gage鼓风计blast meter鼓风控制blast control鼓风量blast volume鼓风门blast gate鼓风压力blast pressure鼓风重量blast weight榖粉黏结剂cereal binder固定板fixed plate固定环fixed collar固定浇桶stationary ladle固定模，固定压铸模fixed die固定模板，固定压铸模板fixed die plate 固定磨轮机(法飞边) fioor grinder固定式摔砂造模机stationary slinger固定碳fixed carbon固熔体solid solution固态合金损失impoverishment固体，实体solid固体收缩solid contraction固相曲线solidus curve固相线solidus固硬性树脂黏结剂no-bake binder刮板输送机scraper conveyor刮板造模template molding刮尺(板) strike -off bar刮刀，刮板scraper刮痕scratch刮痕保护surface scratching test刮痕硬度试验scratch hardness test刮浆板loam board刮平strike strike off刮砂strick刮砂striking off sand刮心平刮板core strickle观察孔observation hole管，缩孔，缩管(铸疵) pipe管件，管接头pipe fittings管抹镘pipe sleeker管制图表control chart管状竖浇刀切刀tubular sprue cutter 管状心型撑pipe chaplet贯通炉straight-flow furnace惯性集尘器inertia dust collector灌浆grouting灌浆造模法grout molding灌模能力(浇铸) filling capacity罐，釜pot光镘smother光面加工hardwarefinish光谱分析spectroscopic analysis光谱照相spectrograph光学高温计optical pyrometer光学显微镜optical microscope光泽碳(添加剂) lustrous carbon规，量规，表，计gage(gauge)规，量规，表，计gauge，gage规测gaging规格外合金off grade metal龟甲纹(铁水面) tortoise shell figure轨道track贵金属noble metal滚光barreling滚光机，滚筒tumbling barrel滚光机，滚筒tumbling mill滚光机，滚筒，齿轮换向器tumbler 滚光机，滚筒，齿轮换向器tumbling 滚式浇桶barrel type ladle滚台喷粒机shot tumblast滚筒试验(铸焦) tubmbler test滚转机rollover machine滚子床，滚子输送器roller bed滚子输送机rooler conveyer滚子输送机岔道roller conveyer switch滚子输送机台roller conveyer table滚子台roller table辊碎机roll crusher辊轧厂，辊轧机rolling mill辊轧机roller mill锅炉boiler锅炉配件boiler fittings国际铸造工程学会ICFTA(International Committee of Foundry Technical Association) 裹冷珠entrapped cold shot裹贴法coating process裹贴砂coated sand过饱和super-saturation过道，通路gangway过低温金属液dull metal过度处理over-treatment过度接种over-inoculation过度应力over-stress过共晶合金hypereutetic alloy过共晶铸铁hypereutectic cast iron过共析钢hypereutectoid steel过共析铸铁hypereutectoid cast iron过搅拌(熔铜除氧) over poling过浸蚀over etching过冷super-cooling过冷undercooling过冷石墨undercooled graphite过量金属excess metal过滤filtration过滤袋pocket filter过滤器filter过滤器，滤渣片strainer过滤式集尘器filtration dust collector过滤心型strainer core过滤用砂心core strainer过热over-heating过热super heat过热处理super heating过热度degree of superheat过热鼓风super-heating blast过热率，升温率super-heating rate过烧金属，过烧金属液burnt metal铪(Hf) hafnium海湖滨砂beach or lake sand海军黄铜admiralty brass海军黄铜naval brass海军炮铜admiralty gun-metal海绵铁spongy iron海绵状腐蚀graphitic corrosion海绵状铸件(铸疵) spongy castings海砂sea sand氦(He) helium含尘量dust content含量content含黏土份containing clay汗点(铸疵) sweat焊珠weld bead焊珠修补bead forming号角形进模口，号角形浇口horn gate 合成单元模砂synthetic unit sand合成模砂synthetic molding sand合成黏结剂synthetic binder合成砂synthetic sand合成树脂模型synthetic resin pattern 合成铸铁synthetic cast iron合钉，定位销dowel合钉，定位销dowel pin合金alloy合金钢alloy steel合金钢铸件alloy steel castings合金晶粒轧辊alloy grain rool合金冷硬轧辊alloy chilled rool合金生铁alloy pig iron合金元素alloying element合金铸钢alloy cast steel合金铸铁alloy cast iron合理计划rationalization scheme合模，装配assembly合模飞边joint fin合模飞边joint flash合模机closing device合模机top box closing machine合模记号assembly mark合模记号sighting mark合模记号tally mark合模记号，假中间模箱false cheek合模面joint face合模面joint surface合模面边角压坏crushes of parting edge合模面压坏crushes of parting surface合模填缝，合模封条joint sealing合模线joint line合模线，装配机assembly line合模销closing pin合模销mold closing pin合模销projection合模楔子closing wedge合模压(压铸模) die closing force合模装置mold closing mechanism合砂机sand blender合箱机molding box closing device合箱销子flask pins合用应力operating stress河砂river sand褐煤lingite褐铁矿limonite黑浆black wash黑浆blacking wash黑铅，石墨black lead黑色涂料foundry blacking黑涂料black黑心展性铸铁，黑心可锻铸铁blackheart malleable cast iron 痕迹，微量trace恒久连续铸造permanent continuous casting恒温器，整温器thermostat横断面cross section横拱transverse arch横流道cross gate横流道，浇槽，出铁槽，轨轮(起重机) runner横流道尾extended runner横流道尾runner extension横强度transverse strength横弯曲试验transverse bending test横行输送机transverse conveyor烘模机mold dryer烘模炉mold oven烘模炉，干燥炉baking oven烘干强度baked strength烘干砂心baked core烘干透气度baked permeability烘砂机sand disintegrator烘砂机sand oven红丹，红铁粉red iron-oxide，rouge 红丹，红铁粉red oxid，rouge红丹，红铁粉rouge，red iron oxide 红黄铜red brass红热脆性red shortness红热温度red heat temperature红外线干燥炉infra-red stove(dryer) 虹吸管砖(撇渣用) siphon brick虹吸流道syphon runner虹吸砖syphon brick厚壁铸件heavy castings厚度thickness厚度检验thickness inspection厚度泥片thickness strip厚度效果试验cast thickness effect test 厚断面heavy section后处理after-treatment后端出渣槽rear slagging spout后期吹风after-blow后期加热post heating后期接种post incoulation弧面，曲度camber弧形砖radial brick胡桃木walnut胡桃木离模粉walnut parting湖砂lake sand糊浆paste糊精dextrin虎克定律Hook's law虎钳，老虎钳vice，vise护面罩face shield护面罩(熔接用) head screen护目镜goggle护眼罩eye shield华氏标度Fahrenheit滑动式浇桶slide ladle滑国组block and tackle滑轮组吊车pulley block hoist滑石talc化合碳combined carbon化学成分chemical composition化学分析chemical analysis化学性质chemical properties划线针scriber还原reduction还原带zone of reduction还原剂reducing agent还原期reducing period还原渣reducing slag环秤(风量计) ring balance环形进模口ring gate环形裂缝(木材) ring shake环形流道ring runner环氧树脂epoxy resin环状加热rim type heating缓冲剂cushioning缓冲冒口relief sprue缓冲砂心splash core缓冲效果buffering effect缓冲效果cushioning effect换班时间downtime for change-over换榇relining换置组件(压铸模) rephosphorization黄铁矿iron pyrite黄铜brass黄铜yellow brass黄铜铸件brass castingss黄杨木box-wood灰(口)生铁gray pig iron灰(口)生铁grey pig iron灰(口)铸铁gray cast iron灰(口)铸铁gray iron灰(口)铸铁grey cast iron灰，灰分ash灰尘Dust灰尘成分dust constituent灰尘湿润装置dust wetting plant挥发volatilization挥发物volatile matter回程装置(压铸) return facilities回火，调质tempering回火，加水调和temper回火脆性temper brittleness回火麻田散体，回火麻田散铁(吐粒散铁) tempered martensite 回火碳temper carbon回炉废料return scrap回炉料foundry returns回炉料returns回炉料scrap returns回热，蓄热，再生regeneration回收率recovery回收率，成品率yield，yield rate回转筛gryatory sieve回转筛gyratory screen回转压碎机gyratory crusher回旋浇口spinner gate回旋浇口whirl gate回转出料盘rotating discharge plates回转浇铸机rotary casting machine回转起模draw on rollover回转输送机rotary conveyer桧木cypress混合物，铁液混合炉mixer混合用浇桶mixing ladle混练mulling混练机muller混碾机盘pan of the mill混碾砂mill sand混砂机edge mill混砂机edge runner混砂机molding sand mixer混砂机sand mark混砂机sand mixer混砂机盘pan of the sand mill活动扳手monkey wrench活动模板(压铸) ejector die half活动凸缘(模型) loose flange活动销movable pin活化activation活化剂activating agent活化剂activator活扣砂模snap flask sand mold活扣砂箱snap flask活扣砂箱造模机snap molding machine 活性黏土active clay活性膨土activating bentonite活字合金type metal火铲fire shovel火花罩spark arrester火箱fire box火星罩fire-spark arrester火焰熔刮flame gouging火焰退火flame annealing火焰硬化flame hardening火砖灰修补daubing火嘴burner port钬(Ho)(稀有金属) holmium基础螺栓，底脚螺栓anchor bolt基地(金相) matrix基地组织(金相) matrix structure基砂base sand畸变distortion箕式升运机bucket elevator机车式摔砂造模机locomotive type slinger 机顶贮砂斗surge hopper机器铲mechanical shovel机械光制machine finish机械试验mechanical test机械试验法mechanical testing机械性质mechanical property机械造模machine molding机械铸造machine casting积弓形片模型segments击耗batter击落浇冒口flogging极高电力ultra-high power极具用铸铁engineering cast iron极具铸件engineering castins极软钢dead soft steel极限抗拉强度ultimate tensile strength极限强度ultimate strength集尘器，集尘机dust collector集尘设备dust collectinn plant集尘效率collection effiiency集渣闸slag trap挤制机extruding machine计件工incentive operator计值图nomograph记号marking记录控制仪recording controller记录仪register加大砂心头enlarged coreprint加工工业processing industry加工袷度finish allowance加工袷度finishing allowance加工量amount of finish加工硬度work hardness加工硬化work hardening加料charge加料charging加料铲peel加料斗charging bucket加料机charge加料机charging machine加料记录charge book加料记录charging sheet加料口charging hole加料口charging opening加料漏斗charging hopper加料门charging door加料盘charging pan加料起重机charging crane加料设备charging equipment加料台charging desk加料台charging floor加料台charging platform加马固溶体gamma solid solution加马黄铜gamma brass加马射线gamma rays加马射线检查法gamma radiography加马射线检验gamma-ray inspection加马射线图gamma radiograph加马射线图gamma-graph加马铁gamma iron加马硅铝明(铝硅合金) gamma silumin加钠处理sodium modification(AI-SI-alloy) 加强带reinforcing band加强肋reinforcing rib加热板heating plate。
机械铸造英语词汇及句法翻译
机械铸造英语词汇及句法翻译在机械铸造领域，有许多英语词汇和句法需要进行翻译。
以下是一些常用词汇的英语译法和一些常见句法的翻译示例：1. 词汇翻译：- 机械铸造：mechanical casting- 铸造工艺：casting process- 铸造材料：casting material- 铸造温度：casting temperature- 铸造工装：casting mold- 铸件表面质量：casting surface quality- 铸件尺寸误差：casting dimensional error- 铸造设备：casting equipment- 铸造模具：casting die- 铸造缺陷：casting defect- 铸件设计：casting design2. 句法翻译示例：- 铸造是将熔化的金属倒入预先准备好的模具中，待其冷却凝固后取出的过程。
翻译为：Casting is the process of pouring molten metal into a prepared mold and then removing it after it has cooled and solidified.- 铸造过程中，需要控制合适的温度来保证铸件的质量。
翻译为：In the casting process, it is necessary to control the appropriate temperature to ensure the quality of the casting.- 铸造材料的选择对于铸件的性能至关重要。
翻译为：The choice of casting material is crucial to the performance of the casting.- 铸造设备的更新和升级是提高生产效率的重要手段。
翻译为：Updating and upgrading casting equipment is an important means of improving production efficiency.- 铸件设计应考虑到尺寸误差和表面质量等因素。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
铸造学专业英语词汇(20)[整理]发布于:2007-05-17 12:18:32热加工，热作 hot working热接点 hot junction热浸镀金法 hot dip metal coating热绝缘 heat insulation热均衡 thermal balance热扩散 temperature diffusivity热量 calorific value热量计 calorimeter热量均衡 heat balance热裂 heat checking热裂 hot tear热裂 hot tear crack热裂(铸疵) hot crack热敏感 heat reactive热敏感性 heat-reactivity热凝性 thermosetting热膨胀 thermal expansion热膨胀计 dilatometer热膨胀计 thermal dilatometer热熔模型 heat-disposable pattern热升降率 thermal gradient热室压铸机 hot chamber die casting machine热收缩 thermal contraction热塑性 thermoplasticity热铁 wrought iron热铁，工业用纯铁 ingot iron热透气性 hot permeability热匣法 hot box process热匣砂心吹制机 hot box core blower热匣粘结剂 hot box binder热效率 thermal efficiency热循环 thermal cycle热应力 thermal stress热硬结性树脂 thermosetting resin热硬黏结剂 hot hardening binder热震 heat shock热震 thermal shock热震阻力 resistance to thermal shocks热铸裂(铸疵) hot casting crack人工干燥(木材) artificial seasoning 人工砂 artificial sand人工时效 artificial ageing人工通风 artifical ventiation人造固体燃料 artificial solid fuel 人造石墨 artificial graphite韧化 patenting韧性 toughness韧性试验 toughness test日本铸造协会 J.F.S.容积配料 dosage by volume容器 container容许~差 allowable error""容许食?" permissible dust emission"容许重?" allowable limit溶混性 miscibility溶胶 sol溶解度 solubility溶解度曲线 solubility curve溶体化热处理 solution heat treatment 溶液 solution溶质 solute熔成菱镁石 fused magnesite熔点 melting point熔点，软化点 fusion point熔钢液面控制 steel level control熔刮 gouging熔锅 melting pot熔锅上涂料 pot dressing熔化 melting熔化，炉次，熔化液 melt熔化比 melting ratio熔化带 melting zone熔化范围 melting range熔化能量 melting capacity熔化期 melt down熔化期 smelting period熔化器具 melting tool熔化潜热 latent heat of fusion熔化设备 melting unit熔化速率 melting rate熔化速率 melting speed熔化温度 melting temperature熔化状况 melting conditions熔剂，助熔剂 flux-covering熔接，焊接，锻接 welding熔接条，焊条，电焊条 welding rod熔接性，焊接性，锻接性 weldability熔接应力 welding stress熔接硬面法，加焊硬面法 hard facing熔接状态，焊接状态 as-welded熔结块，煤渣 clinker熔解期熔化期 melting down熔解损失熔化损失 melting loss熔炼，冶炼 smelting熔炼工，冶炼厂 smelter熔炼领班 head melter熔欠炉加料 cupola charge熔欠炉加料机 cupola charging machine熔入型模(感应电炉) consumable former熔砂，烧毁铸砂 fritted sand熔失型(感应电炉) lost former熔态金属 molten metal熔铁，铁水 molten iron熔铁炉，冲天炉 cupola furnace(cupola)熔铁炉，冲天炉 cupola，cupola furance熔铁炉榇 cupola lining熔铁炉出铁槽 cupola runner trough熔铁炉捣榇 cupola stamping lining熔铁炉点火器 cupola lighter熔铁炉点火器 cupola torch熔铁炉工 cupola tender熔铁炉鼓风机 cupola blower熔铁炉火星罩 cupola spark arrester熔铁炉集尘器 cupola dust arrester熔铁炉控制设备 cupola control equipment 熔铁炉炉壳 cupola shell熔铁炉炉体 cupola body熔铁炉炉砖 cupola brick熔铁炉体 cupola shaft熔铁炉烟囱 cupola stack熔铁炉展性铸铁 cupola malleable iron熔析，液化作用 liquation熔消模型 expendable pattern熔消模型材料 expendable pattern materials 熔液静化 kill the melt熔液漏出 leak-out熔渣 slag熔渣水泥 slag cement熔渣针孔(铸疵) slag pinhole熔锥 fusible cone熔锥 melting cone熔锥 Seger's cone熔锥号数 Seger's number融砂，熔砂 fused sand融砂，熔砂 fusion of sand揉合 knead揉合机 kneader揉合机 kneading mill揉砂机 sand inclusion肉厚感度 section sensitivity铷(Rb)(稀金属元素) rubidium蠕虫状石墨 vermicular graphite乳化作用 emulsification软钢 mild steel软钢 soft steel软焊，锡焊 soldering软焊料，锡焊料 solder软化处理 softening软化点 sagging point软化点 vitrification point软化试验(耐火材料) squatting test软化退火 soft annealing软化退火 softening anneal软水剂，软水器 softener软铸铁 soft cast iron瑞典生铁 Swedish iron锐锯机 saw sharpener润滑性 lubricating property撒粉袋 dust bag撒粉袋 dusting撒克管形进模口，撒克管形浇口 saxophone gate 洒水熔铁炉 water shower cupola塞杆 stopper rod塞进器，加磷器 phosphorizer塞孔浇池 plugged pouring basin塞头(浇桶) stopper end塞头浇池 stoppered pouring basin塞头式浇桶 bottom pouring stopper ladle塞罩法 plunging method三班工作 three-shift operation三倍周波电炉 triple frequency funace三层砂箱 three-part flask[词博科技英语] 沪ICP备06032490号永久域名:谢谢您的支持铸造学专业英语词汇(21)[整理]发布于:2007-05-17 12:18:32三股连续铸造机 threee-strand continuous casting machine三角锉 triangular file三角形进模口 triangular ingate三节熔铁炉，顶加料熔铁炉 top charge cupola三元合金 bernary alloy三重熔炼 triplex melting散热片 radiation fin散热器 radiator扫瞄电子显微镜 scanning electron microscope扫刷 brush sweeper扫刷 sweeper沙兰绳(砂心用) Saran砂 sand砂布 sand cloth砂仓 sand barnker砂仓 sand silo砂处理 sand conditioning砂处理场 sand plant砂处理设备 sand preparation equipment砂床 cast bed，sand bed砂床 sand bed砂床 sand-filling frame砂带打磨机 belt grinder砂底 sand bottom砂碟，金属粒，粒，磨尘 grit砂痕(铸疵) sand lump breaker砂回收场 sand reclamation plant砂结合力 sand bond砂孔(铸疵) sand grain砂库 sand bin砂块打碎机 sand line砂框 sand floor砂粒 grand master pattern砂粒 sand frame砂粒度 fineness of sand砂粒细度指数 grain fineness number砂砾层 gravel bed砂漏斗 sand hole砂轮切断机 abrasive cut-off machnie砂轮修整器 grinding wheel dresser砂模壁移动 mold wall movement砂模技工 molder砂模夹坏(铸疵) clamp-off砂模夹渣(铸疵) slagging of sand，slagging of coating 砂模偏移(铸疵) mold shift砂模散块浮起(铸疵) raise of mold pieces砂模生铁 sand casting pig iron砂模下垂(铸疵) sag mold砂模虚筋填补 molding stopping off砂模压坏 crush of mold砂模压重 mold weights砂模硬度 mold hardness砂模硬度计 mold hardness tester砂模铸件 sand castings砂模铸轧辊 sand roll砂凝聚力 cohesion of sand砂耙 dredge砂胚模型(嵌模用) sand pattern砂渗配 sand tempering砂试验 sand test砂箱，模箱 casting box砂箱，模箱 flask砂箱，模箱 molding box砂箱，模箱 molding flask砂箱，模箱，盒 box砂箱变形 distortion of molding box砂箱隔条 box bar砂箱隔条 cross bar砂箱隔条 flask bar砂箱夹 clamp砂箱夹 flask clamp砂箱肋条 jet bar砂箱手柄 flask handle砂箱造模 box molding砂箱转运机 molding box transfer device砂心搬运车 core truck砂心板 core making plate砂心板 core plate砂心崩散性 core collapsibility砂心车床 core turning lathe砂心吹疵(铸疵) core blow砂心吹射 core shooting砂心吹射机 core shooter砂心吹制机 core blower砂心吹制机 core blowing machine砂心垫砂 bedding a core砂心端承，砂心头 core print砂心翻转提升机 core turn-over and lifting machine 砂心工场 core shop砂心工模 core jig砂心骨 rodding砂心骨，炉条，格子 grid砂心固定 core fixing砂心固定安全装置 core interlocking safety device 砂心盒，心型盒 core box砂心盒通气孔 core box vent砂心机 core machine砂心机 core making machine砂心机 core molding machine砂心记号 core mark砂心夹 core clamper砂心间 core room砂心胶 core gum砂心胶合剂 core paste砂心框 core frame砂心模 core maker砂心模板 core template ，core templer砂心磨床 core grinder砂心耐火度 core fefractoriness砂心泥 core mud砂心黏合 gumming of cores砂心黏结剂 core binder砂心黏结剂 core compound砂心喷涂器 core sprayer砂心偏移(铸疵) core shift砂心破裂，心模破裂(铸疵) broken core砂心干燥 core drying砂心干燥炉 core drying oven砂心干燥炉 core oven砂心干燥炉 core stove砂心清砂 decoring砂心清砂机 core knockout-machine砂心上浮(铸疵) core raise砂心式进模口 core gate砂心填料 core fillen砂心通气孔 core vent砂心通气蜡条 core vent wax砂心涂浆 core wash砂心涂料 core coating砂心涂料，砂心整修 core dressing砂心托板 core carrier plate砂心托板 core drier砂心托架 core carrier砂心下垂(铸疵) sag core砂心压坏 crush of core砂心摇台 core cradle砂心硬度 core hardness砂心硬化烘炉 core curing oven砂心油 core oil砂心制造法 core bonding system砂心装置 core setting砂心装置工模 core setting jig砂心装置夹具 core setting fixture砂心自动翻黑心脱模机 automatic rollover core stripping machine 砂心组合 core assembly砂心组合夹具 core assembling fix ture砂心组合夹具 core assembling jig筛 screen筛 sieve筛分 screening筛分砂 riddled sand筛纲 screen cloth筛孔 aperture，sieve筛孔，纲目 sieve mesh筛孔，纲眼，纲目 mesh筛孔尺寸 mesh size筛孔分析 screen analysis筛孔分析，筛析 mesh analysis筛孔筛 mesh screen筛孔筛 mesh sieve筛砂机，筛砂装置 sand sieving machine筛砂机，筛砂装置 sand sifter筛析 sieve analysis筛析试验 sieve analysis test筛屑 screenings筛眼 sieve opening铸造学专业英语词汇(22)[整理]发布于:2007-05-17 12:18:32山毛榉 beech杉木 cedar钐(Sa)(金属元素) samarium商品级 commerical grade上表面气孔(铸孔) top surface porosity上浮(石墨)，浮悬法 rlotation上灰泥(包模铸造)，敷砂 stuccoing上宽铸锭模 gradient mold上模 mold cover half上模 top part上模，上砂箱，上模箱 cope上模板 cope plate上模合模机 cope closing machine上砂箱，上模箱 cope box上砂箱，上模箱 cope flask上砂箱支框 offfset上升浇铸 cast up-hill上升浇铸法，底浇法 uphill running上涂料 facing上涂料，粉刷，清理 dress上涂料，涂料，清理(铸件) dressing烧杯 beaker烧博灰，吸湿灰 daub烧毁铸砂 burned sand烧毁铸砂 burnt sand烧僵，僵烧 dead burning烧结 sintering charge烧结(铸砂) burning烧结白云石 burnt dolomite烧结白云石 clinkered dolomite烧结苦土地(氧化镁) sintering烧结料 sintering of sand烧裂 fire-crack烧裂(铸疵) crazing烧磨土 chamotte烧磨土粉 ground chamotte烧磨土砂 chamotte sand烧磨土砖 chamotte brick烧失 ignition lost烧失性模型(聚苯乙烯) disposable pattern烧石膏 plaster of paris烧熟料 overburnt material烧硬氧化镁 hard burned mangesia蛇骨型架 bellow cross parallel射注速率(压铸) shot speed摄氏温度计 Celsius's thermometer伸长，伸长率 elogation伸长百分率 percentage of elongation伸长计 extensometer伸展机 stretcher砷(As) arrsenic深冷处理 sub-zero treatment深蚀 deep etching沈淀物 sediment渗出 exudation渗铬 chromizing渗铝防锈法 calorizing渗漆法 enamel empregnatin渗碳 carburization渗碳 carburizing渗碳 cementation渗碳氮化物 carbonitriding渗碳钢 cementaed steel渗碳剂 carburizer渗碳剂 carburizing agent渗透 osmosis渗透融结(铸疵)，渗透熔接 fusion penetration 升降机(电梯) elevator升降台 lifting table升降运送车 lift truck升温时间 heating-up time生产报告 production statement生产成本 production cost生产费用 working cost生产管制 production control生产计划 production plan生产线 production line生石灰 quick lime生铁 pig生铁 pig iron生铁锭流道 sow生铁锭铸模 pig mold生铁切断机 pig breaker生铁切断机 pig iron breaker生锈 scaling生粘土 green clay声音传播 sound transmission盛渣桶 slag pot剩余熔液 out pour失败炉次 off heat施釉，上漆 enamelling湿度 humidity湿分 hygroscopic water湿模铸件 green castings湿强度 green strength湿砂 green sand湿砂 wet sand湿砂结合强度 green bond strength湿砂模 green sand mold湿砂透气性 green permeability湿砂心型，湿砂砂心 green sand core湿砂造模法 green sand molding十字接头，错合(铸疵) cross joint石膏 gypsum石膏模 gypsum mold石膏模 plaster mold石膏模型 gypsum pattern石膏模型 plaster pattem石膏模造模法 plaster molding石膏水泥 gypsum cement石灰 lime石灰石 lime stone石灰石熔剂 lime stone flux石灰窑 lime kiln石棉 asbestos ，asbestus石墨，碳精 graphite blacking石墨棒消耗量 graphite rod consumption 石墨分布 graphite distribution石墨化 graphitization石墨化促进剂 graphitizer石墨化接种剂 graphitizing inoculant石墨化退火 graphitizing annealing石墨化展性处理 malleablization by graphitizing 石墨晶粒大小 graphite size石墨砂孔巢(铸疵) graphite nest石墨碳 graphite-clay brick石墨涂料 graphite carbon石墨涂料 graphite facing石墨形状 graphite form石墨砖 graphite crucible石松子粉 lycopodium powder石英 quartz石英粉 quartz flour石英管 quartz tube石英岩 quartzite石油焦 petroleum coke石油聚合物 petroleum polymer时间温度曲线 time-temperature curve时效 secular charge，aging时效，成熟 ageing，aging时效，季化(铸件)，风干(木材) seasoning时效钢 aged steel时效硬化 age hardening实际粒度 actual grain size实际裂断负载 actual breaking load实际生产量 actual production实体废料(金属) heavy scrap实物模型 natural pattern实样造模 mold from a casting实样造模 molding from a casting蚀孔(铸疵) cavitation erosion史帝田铁，史帝田体 steadite史斗铬钴(钴铬钨合金) stellite使用范围 range of application市售钢材 merchant steel示温熔锥 pyrometric cone示温熔锥当量 pyrometric cone equivalent室形炉 chaimber furance试车 trial run试合模 trial closing试块 test block试片 test piece试砂筛 sand ftsting sieve试验棒 test bar试验工场 pilot plant试验室用炉 laboratory furance试样 specimen试样，样品 sample试样胚 coupon试作铸件 pilot castings铈(Ce) cerium收尘器 dust catcher收集w 仓 collecting bunker收缩 constriction收缩 necking down收缩 shrink收缩 shrinkage收缩，缩水 contraction收缩变形 contraction distortion收缩袷度 contraction allowance收缩气孔巢(铸疵) shrinkage porosity收缩裕度 shrinkage allowance铸造学专业英语词汇(23)[整理]发布于:2007-05-17 12:18:32手柄，吊柄 handle手持面罩 hand screen手持面罩 hand shield手锤 hand hammer手捣杆 hand rammer手电筒 flash light手动挤压造模机 hand squeezer手动造模机 hand molding machine手风箱，皮老虎 bellows手风箱，皮老虎 hand bellows手工捣砂 hand ramming手工加料 hand charge手工造模 hand molding手工造模 tucking手刨 hand planer手钳 pincers手抬浇桶 bull ladle手提柄浇桶 hand shank手提柄浇桶 hand shank ladle手提浇斗 bowl手提浇桶 hand ladle手提磨轮机 portable grinder手推车 hadnd carrier手推平车 hand truck手压挤 manual squeeze受热面 heating surface受压软化(耐火砖) softening under load书型模法 booking书型铸模 book mold输砂设备 sand conveyor installation输送机 conveyor syste输送量 quantity delivered输送盛桶 transfer ladle输送线 conveyor line熟黏土 grog熟黏土砂 compo数据控制，数值控制 numerical control(NC) 竖浇道 sprue竖浇道棒 sprue bar竖浇道棒定位销 sprue button竖浇道底 sprue base竖浇道底 sprue bottom竖浇道孔 sptue hole竖浇道塞 sprue plug竖浇道塞 sprue plug valve树皮 bark树枝状结晶 dendritic sgegregation树枝状晶间偏析 interdendritic segregation 树枝状晶间石墨 interdendritic graphite树枝状模型(包模铸造) tree树枝状组织 dendritic structure树脂 resin树脂调质 resin modification树脂调质砂心油 resin modified core oil树脂里贴工场 resin bonding plant树脂里贴砂 resin coated sand树脂黏结剂 resin binder树脂黏结剂，塑料黏结剂 plastic binder树脂砂 resin sand树脂砂心黏结剂 pastic core binder树脂微粒 resin paticle刷子，毛笔 brush摔砂头(摔砂造模机) ramming head摔砂造模机 sand slinger摔砂造模机 sand thrower摔砂造模机 slinger闩键，闩块(砂心) kicking block栓塞 plug双带式输送机 twinbelt conveyor双端心型端承，双端砂心头，双端砂心端承 double core print 双端窄匙 double ender双股连续铸造机 twin-strand continuous casting machine双轨吊运车 two-rail trolley双连风口 twin tuyeres双梁式架空移动起重机 two-girder overhead travelling crane 双面模型板 double sided pattern plate双面模型板，中板 match plate双室炉 double chamber furnace双膛炉 double hearth furnace双圆抹镘，双端抹角弧片 double ended radius sleeker双站式造模机 two station molding machine双重熔化 duplexing双重熔化法，双炼法 duplex process双重收缩 double contraction水玻璃，水位计 water glass水淬火 water quenching水淬粒渣 water granulated slag水分 moisture水分测定器 moisture tester水分试验 moisture test水罐 water pot水冷 water cooling水冷风口，水冷风嘴 water-cooled tuyere水冷套 water-cooled jacket水煤气 water gas水泥，胶结剂 cement水泥模 cement bonded mold水泥模砂 cement sand水泥模型 cement pattern水泥造模法 cement molding水平旋转台 horizontal rotating table水平仪 level水韧法 water toughening水刷 swab水套式熔铁炉 water jacket cupola水压试验 water test水银(Hg) quick-silver水银柱 mercury column顺磁性 para-magnetism顺形心型，顺型砂心撑 contoured chaplet顺形压挤板(造模机) contoured csqueeze plate顺序抽样 sequential samplin顺序控制 sequential control四元合金 quaternary alloy似块状石墨 quasi-flake graphite松弛试验 relaxation test松件 loose piece松件模型 loose pattern松件模型 loose piece pattern松扣 free松木 pine松散 aeration松散度(铸砂、铸焦实验用） shatter value松砂 aerate the sand松砂 cut sand松砂机 sand aerator松砂机(砂处理)分离器(空气污染控制用) disintegrator 松砂机，充气器 aerator，airator松砂机，充气器 airator，aerator松砂松砂 sand cutter松砂要 sand cutting松箱板具 mold release trigger松销 loose pin松脂，松香 rosin送风式炉，鼓风式坩埚炉 wind furnace素来铁(加拿大产特种生铁) Sorel metal速成展性铸铁 quick malleable iron粟木 chest-nut塑料涂料 plastic coating塑性 plasticity塑性变形 plastic deformation酸醇树脂 alkyd resin酸度 acidity酸度，pH，离标 hydrogenexponent酸洗 cleaning with acid酸洗 pickling酸性柏思麦法 acid Bessemer process酸性柏思麦钢 acid Bessemer steel酸性柏思麦转炉 acid Bessemer converter酸性衬 acid lining酸性电弧炉 acid electric arc furance酸性电炉钢 acid electric steel酸性钢 acid steel酸性火砖 acid brick酸性浸蚀 acid etching酸性耐火烧火燎材料 acid refractory material酸性平炉 acid open-hearth酸性平炉法 acid open-hearth process酸性s堵?acid open-hearth steel酸性熔渣 acid slag酸性生铁 acid pig iron酸性试验 acid test酸性氧化物 acidic oxide酸性渣法 acid slag pracitice酸性转炉 acid converter随意采样 random sample碎焦炭 breeze coke碎焦炭 coke breeze碎料 small scrap碎裂 shatter crack铸造学专业英语词汇(24)[整理]发布于:2007-05-17 12:18:32碎砂机，松砂机 sand breaker碎铁 bushelling碎心锤 core buster碎心机 core breaker隧道炉 tunnel furnace隧道炉，隧道干燥炉 tunnel oven隧道炉，隧道干燥炉 tunnel stove隧道退火炉 tunnel annealing furnace隧道退火炉 tunnel-type annealing furnace隧道窑 tunnel kiln隧道铸铁圈 tunnel casting ring缩尺 pattern maker's rule缩管(铸疵) shrinkage pipe缩颈冒口 feeder head with Washburn core缩颈砂心 breaker core缩颈砂心 break-off core缩颈砂心 wafer core缩颈砂心 Washburn core缩颈砂心，敲落 knock off缩颈砂心，敲落 neck down core缩孔(铸疵) shrinkage cavity缩孔(铸疵) shrinkage hole缩孔[铸疵] shrink hole缩孔倾向 shinkage cavity tendency缩裂(铸疵) contraction crack缩裂(铸疵) shrinkage crack缩面百分率 percentage of area reduction缩面率 reduction of area缩入，渗透 infiltration缩水量 pattern maker's shrinkage缩陷处 shrink mark他型结晶 allotriomorphic crystal铊(Tl) thaljium塔式炉 tower oven台 bench台车，卡车 truck台车，托架，载体 carrier台车轮送机 car conveyor台车式炉 car-bottom furnace抬柄 bull handle抬动浇斗 shank ladle抬动浇桶 carry ladle抬动浇桶 fork ladle台秤 platform scale台上造模法 bench molding台上铸模 bench mold台式磨床 pedestal grinder钛(Ti) titanium钛铁 ferro-titanium钛氧包覆料 rutile covering钛铸铁 titanium cast iron钽(Ta) tantalum探针，铅锺，测锺，试体 probe碳 carbon碳榇 carbon lining碳当量 carbon equivalent碳当量测定剂 CE meter (carbon equivalent meter) 碳粉 carbon powder碳钢 carbon steel碳钢 straight carbon steel碳钢，普通钢 plain carbon steel碳弧熔接 carbon arc welding碳化 carbonization碳化钙，电石 calcium carbide碳化铁 iron carbide碳化物 carbide碳化物安定剂 stabilizers碳化物稳定剂 carbide stabilizer碳化硅 silicon carbide碳化硅压块 silicon carbide briquests碳化渣(白渣) carbide slag碳精棒 carbon rod碳水化合物黏结剂 carbohydrate binder碳酸钠(碱性炉用熔碱) purite碳烟粉 carbon black碳质夹杂物 carbonaceous inclusion碳质砂 carbon sand碳砖 carbon brick汤姆斯钢 Thomas steel搪瓷，瓷漆，珐琅 enamel糖类黏结剂(糖蜜) sugar binder糖蜜 molassesd/出式熔贮炉 bale-out furnace，die casting桃花心木 mahogany陶瓷基砂 ceramic base sand陶瓷滤心 ceramic strainer core陶瓷心型 ceramic core陶模铸造法 ceramic casting陶模铸造法 ceramic mold陶氏合金(镁合金) Dow metal揀丙氏青铜 Tobin bronze套箍(活扣砂箱用) inside band套管滤器 thimble filter套筒板手 box spanner套筒砖 sleeve brick套筒砖浇流道 sleeve runner套箱 jacket套箱 slip jacket套箱，砂框 mold jacket套箱式水冷熔铁炉 jacket type water-cooled cupola特殊模砂 special molding sand mixture特种钢 special steel特种黄铜 special brass特种蒙气退火炉 special atmosphere annealing furnace 特种青铜 special bronze特种铸铁 special cast iron铽(Tb)(稀土元素) terbium梯表试片 step-bar test piece梯表试片 stepped test bar锑(Sb) antimony提砂钩，夹钳，升降杆 lifter提砂钩，清除器 cleaner体心立方格子 body-centered cubic lattice 天平，秤 balance天然模砂 natural bonded molding sand天然黏结砂 naturally bonded sand天然气 natural gas天然砂 natural sand天然石墨电极 natural electrode天然石墨电极 natural graphite天然硅砂 natural silica Sand添加 addition添加剂 addition agent添加剂 additive添加新砂 new sand addition添浇 after-pour填充 back-fill，back-up填充 back-up，back-fill填缝剂 joint mixture填料 packing material填料熔接 fusion of packing macherials填入口，浇口 filling port填砂 filling in填砂，背砂 filler sand填砂框 filling frame填砂框(砂箱用) sand-feeder填隙料，埋筋 filler条状组织 banded structure贴附砂心 super-imposed core铁(Fe) iron铁钉 wire nail铁合金 iron alloy铁焦比 iron to coke ratio铁矿石 iron ore铁耙，心骨突刺 pricker铁水 liquid iron铁水浇铸床 pig bed铁水静压力 ferro-static pressure铁水泥 iron cement铁碳平衡图 iron-carbon equilibrium diagram 铁条 bar iron铁液，铁水 melted iron铁珠 shot iron铁珠，铁水珠(铸疵) iron shot铁铸件 iron castings铁砖 iron brick停吹 blowing-out停留时间 stay[ing time]停止鼓风 turn off the blast通风槽，槽构形(感应电炉) channel通风机，通风器 ventilator通风系统 ventilating system通气 venting通气板 vent board通气板 vent plate通气度 venting quality通气杆 vent rod通气管 vent pipe通气孔 air vent通气孔 vent通气孔 vent hole通气孔 whistler铸造学专业英语词汇(25)[整理]发布于:2007-05-17 12:18:32通气口 air port通气蜡条 vent wax通气蜡线 wax vent通气砂心 blind core通气筛嘴(砂心盒) screen vent通气性 vent ability通气针 vent former通气针 vent wire同素异性 allotropy同位素 isotope同质多象 polymorphism桐油 China wood oil酮油 tung oil铜(Cu) copper铜基合金 cupro-metal铜绿 green patina铜气脆性(铸疵) hydrogen brittleness of copper铜缘 patina铜缘 Verdigris筒状浇口(压铸) end gate头等品质 top grade quality透明片 transparent cut透气性 permeability透气性试验 permeability test透气性试验器 permeability tester"凸出块，突耳 casting lug凸疵(铸疵)(模型粘砂) sticker凸肩导销 shoulder guider pin凸块，突耳 lug凸片，飞边 fin凸片管 finned tube凸片气缸 finned cylinder凸缘 flange凸缘抹片 flange sleeker突出标志 rising mark突耳孔 lughole突起分模面 undulating mold joint涂焊(表面硬化涂焊) surfacing涂黑 blacking涂浆，洗涤 washing涂沥表管 tarred pipe涂料 facing materials涂料 wash material涂料，涂模剂 coat涂料，涂模剂 coating涂料疤(铸疵) blacking scab涂料孔(铸疵) blacking hole涂模浆 mold wash涂模浆 molding wash涂模料 mold coating涂模料 mold dressing涂模料 mold facing涂模料接种法 mold coating inoculation 涂刷 painting土状石墨 amorphous graphite吐粒散铁，吐粒散体 trosstite钍(Th) thorium推拔，斜度 taper推拔砂箱 taper flask推拔套箱 taper case推车式浇桶 buggy ladle推挤(压铸) squeezing退火 annealing退火罐 annealing pot退火炉 annealing furance (oven)退火温度 annealing temperature退火箱 annealing box退火用填料，退火用矿粉 annealing ore退货 rejection托板 pallet托板输送机 pallet conveyor托板输送机 plate conveyer托架 bracket托运板 carrying plate脱件销(压铸) sprue puller pin脱蜡 burn-out脱蜡 dewaxing脱蜡法 lost wax process脱蜡造模法 lost wax molding脱裂强度(模砂式模纵面压裂试验) splitting strength 脱硫，去硫 desulphurization脱硫，去硫 desulphurizing脱模 pattern draw脱模式造模机 pattern-draw molding machine脱湿剂(模砂用) humectant脱碳 decarburization脱碳法展性处理 malleablization by decarburizing脱碳率 rate of decarburization脱硅 desiliconizing脱锌 dezincification椭圆导套 oval bush外观检查 outer inspection外角抹镘 square sleeker外卡钳 outside calipers外冷激，外冷硬，外冷铁 extenal chill外模破裂 broken mold外伸砂心顾 clearance print外伸砂心头 over-hang外伸余度砂心头 clearance taper print外缩(铸疵) draw外缩孔(铸疵) open cavity外缩孔(铸疵) surface shrinkage外缩孔，凹陷(铸疵) depression外缩窝 shrinkage depression外烯式空气预热器 externally fired hot blast heater 外因非金属杂物 exogenous non-metallic inclusion外因金属夹杂物 exogenous metallic in clusion外因凝固 exogenous solidification外圆角 round弯曲负荷 bending load弯曲试验 bending test弯头抹刀 bent spatula完工面 finished surface完全冷激 complete chill完全燃烧 complete combustion完全退火 full annealing完整模型 complete pattern万能试验机 universal testing machine威兼氏砂心，增压砂心 William's core，atmospheric core微粉煤 dust coal微孔巢性(铸疵) microporosity微粒度(底片) grains of sand微粒组织 graininess微量元素 subversive element微量元素 trace element微小硬度计 micro-hardness tester韦克氏硬度 Vicker's hardness，diamond pyramid hardness number 韦克氏硬度计 Vicker's hardness tester伟晶作用 germination未处理原砂 raw untreated sand未静钢 unkilled steel未静钢，净缘钢 effervescing steel未静钢，净缘钢 rimmed steel未空孔 blind hole喂槽 tundish温度阶差 thermal taper温热强度 warm strength文氏管流量计 Venturi meter文氏管洗净器 Venturi scrubber文氏管装置 Venturi apparatus文武镘刀 square trowel稳定平衡图 stabilizing inoculant涡流 eddy current蜗旋电阻线 resistance spiral蜗肇滑槽 spiral chute蜗肇输送机 spiral conveyor沃斯回火法 austempering沃斯田钢 austenitic steel沃斯田化 austenizing沃斯田化温度 ustenizing temperature沃斯田锰钢 austenitic manganese steel沃斯田铁，沃斯田体 austenite沃斯田铸铁 austenite cast iron沃斯田铸铁 austenitic cast iron卧式砂心射制机 horizontal core shooter污泥 sludge污染 pollution污染，污斑 stain钨(W) tungsten钨铁 ferro-tungsten无疵 soundness无疵铸件 sound castings无缝榇料 monolithic lining material无缝炉榇，整体炉榇 monolithic lining无负载时间 no-load time无麻口冷硬层 chill zone without mottle无水酒精 absolute alcohol无头小钉 spring无箱砂模，脱箱砂模 boxless mold无箱造模法 laskless molding无烟煤 anthracite五倍周波感应电炉 quintuple frequency induction furance伍氏合金 Wood's metal铸造学专业英语词汇(26)[整理]发布于:2007-05-17 12:18:32物理变化 physical change物理试验 physical test物理性质 physical properties物理冶金 physical metallurgy雾化 atomization西拉高硅铸铁 Silal吸热反应 endothermic reaction吸入输送机 suction conveyor吸湿性试验(高湿状态) high humidity storage test吸收 absorption吸收剂 absorbent吸收器 absorber析出，沈淀 precipitation析出热处理 precipitation heat treatment析出退火 precipitation annealing析出硬化 precipitation hardening硅(Si) silicon硅肥粒铁 silico ferrite硅肺病，石米沉着病 silicosis硅分析仪，砂计 silicon meter硅钢板 silicon steel plate硅化钙 calcium silicide硅化钙 calcium silicon硅黄铜 silicon brass硅块 silicon briquets硅铝钙合金 calicum-aluminium-silicon硅铝明(铝硅合金) silumin硅锰钙合金 calcium-manganesesilicon硅凝胶，硅胶吸湿剂 silica gel硅青铜 silicon bronze硅青铜 soilzin bronze硅砂 silica sand硅砂捣料 silica ramming compound硅砂粉 silica flour硅砂浆涂料 silica wash硅砂石砖 ganister brick硅树脂，硅酮 silicone硅树脂滑脂 silicone grease硅酸 silicic acid硅酸监 silicate硅酸钠，水玻璃 sodium silicate硅酸四乙酯 tetraethl silicate硅酸乙脂 ethyl silicate硅铁 ferro-silicon硅铜 silicon copper硅线石砖(高铝氧(70Al2O5)硅质耐火砖) silimanite brick 硅岩轮辗硅砂 impeller-breaker sand硅藻土 diatomaceous earth硅藻土 infusorial earth硅藻土 kieselguhr硅质粘土 silicious clay硅砖 silica brick硒(Se)(化学元素) selinium稀土金属 rare earth metal锡(Sn) tin锡汗珠(铸疵) tin sweat锡青铜 tin bronze习用潜变限度 conventional creep limit洗尘器，涤气机 scrubber洗净器 scrubbing liquid细锉刀 finishing file细孔组织 cell structure细裂痕(铸疵) hair crack细裂纹(铸疵) caplillary crack细密波来铁 fine pearlite细泥砂浆 finishing loam细砂，河海丘砂 bank sand细土粉，细泥 fine silt煅烧 calcine煅烧白云石 calcined dolomite煅烧窑 calcining kiln瑕疵 flaw瑕疵大小 flaw size瑕疵位置 flaw location揬工场，揬造炉 fore-hearth forge揬铁锈皮 forge scale揬造，揬件 forging下降速率 lowering speed下浇道，坚浇道 down gate下浇道，坚浇道 down sprue下模 bottom part下模 nowel下模，下砂箱，下模箱 drag下砂箱，下模箱 drag box下砂箱，下模箱 drag flask夏比冲击试验 charpy impact test夏比冲击试验机 Charpy impact test machine 夏比冲击值 Charp impact value纤维状滑石 fibrous talc显热 sensible heat显微镜 microscope显微镜试验 microscopic inspection显微镜学 microscopy显微镜照像 photomicrograph显微偏析 micro-segregation显微缩孔(铸疵) micro-shrinkage显微像 micrograph显微组织 micro-structure限缩变形 hindered contraction限外显微镜 ultramicroscope相 phase相对频率 relative frequency相对湿度 relative humidity相对硬度 relative hardness相律 phase rule相平衡 phase equillibrium相图 phase diagram响铜 bell metal象皮皱纹(铸疵) elephant skin橡胶浇道棒(造模) rubber down gate橡胶浇道棒(造模) rubber pouring funnel橡胶输送带 rubber conveyer belt橡木 oak消除冷硬退火 chill removing annealing消除应力开沟，防裂槽 stress relieving grooving 消泡剂 antifoaming agent消石灰，熟石灰 slake-lime消退 fading消退时限 fading time硝酸浸蚀液 nital硝酸浸蚀液 nitric acid销 pin销合 pin closure销紧力 locking force销孔试验片 keyhole specimen销抬造模机 pin-lift molding machine萧氏精密造模法 Shaw process萧氏硬度 Shore hardness小块料 cobbing小胚 billet小铸件 small castings校准 calibration校准块 calibration block校准钮 calibrating knob楔 wedge楔表进模口 wedge gate楔塞作用 wedge action楔形进模口 wedge runner bar楔形试片 wedge test piece楔形试验 wedge test楔形销 wedge pin楔形压力试验 wedge penetration test楔形砖 key brick楔形砖 wedge brick楔值 wedge value斜导杆(压铸) cam finger斜度砂箱，滑脱砂箱 slip flask斜方晶系(结晶) rhombic system卸斗 skip卸斗吊车 skip hoist心，心型，砂心 core心材 heart wood心骨 core bar心骨 core grid心骨 core iron心骨 core rod心骨管 core barrel心骨矫直器 core rod straightner心骨模 core grid mold心骨模型 core iron printer心骨切断器 core rod cutter心骨轴 core spindle心裂(木材) heart shake心砂 core sand心砂混合机 core sand mixer心形镘刀 large heart trowel心型拔出装置(压铸) core pull assembly心型撑，砂心撑 chaplet心型固定门(压铸) heel block心型滑板(压铸) core slide心型移装，砂心移装 core draw-back心轴，心骨 arbor心座 core bedding frame辛浦森式混砂机 Sympson type sand mill新炼金属 virgin metal新砂 new sand锌(Zn) zinc锌当量 zinc equivalence，zinc equivalent factor铸造学专业英语词汇(27)[整理]发布于:2007-05-17 12:18:32星形裂缝 star shake星形铁(滚光用) jackstar，mill star，star星形铁(滚光用) mill star，jack star，star星形铁(滚光用) star，jackstar，mill star星形铁(滚光用) tumbling stars形象因子 shape factor型砖 shaped brick。