模具专业词汇
模具专业术语英语
模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。
模具专业词汇
汉语英語日语原料硬度一、模胚/模架模胚mold base 金型胚（かながたはい)面板/码模板TP/top clamping plate S45C~S50C 底板BP/bottom clamping plate S45C~S50C 水口推板RP/striper plate S50C~S55C 前模板A/A plate S50C~S55C 后模板B/B plate S50C~S55C 托板SP/support plate S45C~S50C 方铁SB/spacer block [speisә]S45C~S50C顶针面板ERP/ejector retainer[ri'teinә]plate[pleit]S45C~S50C顶针底板EP/ejector plate S45C~S50C 吊模环lifting eye bolts[bәult]SS400隔热板temperature insulator sheets['insjuleitә]二、模芯/型腔型腔（前模芯/定模芯）master cavity型芯 (后模芯/动模芯）master core前模镶件cavity insert后模镶件core insert 镶件insert 嵌め板（めいた）镶针insert pins直边guide pins SUJ258~65HRC 直导套托司/直司guide bushings SUJ258~65HRC 水口边support pins SUJ258~65HRC 水口边介子support pin collars S45C回针return pins SUJ258~65HRC 地脚distance spacers S45C销dowel SKD61镶针insert pins杯头螺丝/平面螺丝socket head cap screws SCM43539~44HRC 无头螺丝screw plugs SCM43537~43HRC拉板tension links S45C 限位螺丝（水口螺丝）stop bolts SCM43533~38HRC 拉杆（山打）螺丝puller bolts SCM43533~38HRC 垫圈（介子）washers S45C 48~52HRC 弹簧垫圈（介子）spring washerSWRH6242~50HRC三、浇注系统浇口sprue bushings/dropSK3/SKD6148~52HRC热嘴hot spave bushing/heated nozzles ノズル热流道hot runner 熱流道热流道支撑块hot runner pillar 定位环/圈locating rings S45C 浇口套/唧嘴弧面gate bushing SKH5159~61HRC即嘴球头sprue radius四、冷却系统冷却管路cooling line 水接头water plug 水嘴water line水道堵头cooling circuit plugs 集水器water manifold五、顶出系统顶针/顶杆ejector pins 直身顶针straightSKH51有托顶针stepped ejector pins SKH51扁顶rectangular ejector pins SKH51斜顶angular ejector pin / lifter 718两次顶出2-step ejector 顶出孔knock out 推杆stripper bar 推方（顶块）ejector block 718气顶air pop直身司筒straight ejector sleeves SKD61有身司筒stepped ejector sleeveSKD61司筒针steps-type center pins SKD61中托司ejector guide bushings SUJ258HRC直导柱（中托司用）ejector guide pins SUJ258HRC水口勾针runner lock pins SKH5159~61HRC 水口勾针套bushings for runner lock pin SKH5159~61HRC 六、出模机构滑块/行位slide滑り塊(かつり）行位压条guide rails SKS353-56HRC T型滑块T slide block738行位slide core units七、辅助机构八、排气系统排气阀air poppets镶件排气insert vent气嘴air fitting其它扣鸡ultra locks SK3顺序开关parting lock sets SKD6150~55HRC 胶塞parting locks弹弓coil spring弹弓导柱spring pins S45C水口弹钉runing ejector sets SKH5159~61HRC 弹弓波子ball plungers闸方taper wedges S45C52~56HRC 锥度块taper block sets SKD1158~62HRC 直身定位块locating block sets S45C~S50C50~60HRC 锥形定位块taper block sets S45C~S50C50~60HRC 耐磨块（硬度块）wear plates718/73855~62HRC 斜导柱(4~8mm)angular pins DC5360~63HRC 斜导柱(10~40mm)angular pins SUJ258~61HRC铲鸡locking block SKS353-56HRC 日期嵌入件mold dating inserts718环保标记（镶件）recycling inserts718撑头support pillars S45C撑方spacer blocks S45C垃圾钉stop pins S45C46~50HRC 顶针板顶出限位stop ring S45C46~50HRC 喉咀joint plugs C3604快换喉咀quick fitting joints电子开关switch限位开关limit switch压板holding plates拉板连接圈links rings S45C38~43HRC 吊模梁shipping strap沉孔counterbore套管bushing分型面parting line分型面锁parting line bolt直边锁straight lock计数器mold shot counter分型面承压块hardened parting line pad撬模角pry bar slot中导柱guided ejection螺丝孔screw hole板销钉dowel弹簧spring导向杆/复位杆tapped return pin油嘴hydraulic fitting油路集流阀hydraulic manifold锁模块parting line strap定位环locating ring行程开关switch mount蚀纹texture 码模槽clamp slot油缸油詰め（ゆ导柱guide pin /leader pin はしら螺丝孔screw ネジの穴（あな）铍铜moldmax热电偶thermocouple。
模具专业相关英语词汇大全
模具专业相关英语词汇大全barrel 滚筒(加工)bending 波纹加工broaching 拉刀切削centering 定中心cutting 切削cylindrical lathe cutting外圆车削electric discharge machine放电加工electrolytic grinding 电解研磨embossing 压花加工facing 面车削filing 锉刀修润hand finishing 手工修润hemming 卷边加工hobbing 滚齿加工joggling 摇动加工lapping 抛光/研磨修润laser beam machining 雷射加工lathe cutting 车床车削planning 刨削加工polishing 抛亮光reaming 铰孔修润rough machining 粗切削rounding 圆形加工sawing 锯削scaling 清除钢碇缺陷shaping 成形加工skiving 表面研磨slotting 切缝切削taper turning 锥度车削thread cutting 螺纹切削ultrasonic machining超音波加工up cut milling 逆铣加工二.模具砂轮用语英语词汇abrasive 砂轮Al2O3 氧化铝borazon 氧化硼立方晶buffing wheel 抛光布轮diamond 钻石dresser 砂轮整修机dressing 修整endless grinding belt循环式研磨带finishing allowance 加工余量grain 磨粒grinding disc 研磨盘jamp up 孔眼堵塞mesh 网筛目resinoid grinding wheel半树脂型砂轮slitting 切缝量vitrified 陶瓷的三.模具锻铸造相关英语词汇accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning离心喷光all core molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱camlachie cramp 铸包cast blade 铸造叶片casting flange铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心filling in 填砂film play 液面花纹finishing slag 炼後熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件四.模具线切割放电加工相关英语abnormal glow 不规则辉光放电arc discharge 电弧放电belt 皮带centreless 无心chrome bronze 铭铜clearance angle 後角corner shear drop 直角压陷deflection 桡曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 间隙graphite 石墨graphite contraction allowance 电极缩小余量graphite holder 电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working 肋部加工roller electrode 滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂tungsten bronze 钨青铜waviness 波形起伏working allowance 加工余量working dischard 加工废料五.模具冲压机械及周边英语词汇back shaft 支撑轴blank determination 胚料展开bottom slide press下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面camlachie cramp 铸包chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press调整冲模用压力机double crank press双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press精密下料冲床forging roll 辊锻机finishing slag 炼後熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press手动齿轮齿条式冲床hand screw press手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device微寸动装置microinching equipment微动装置moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine旋压成形机spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机六.模具冲模加工英语词汇barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工coining 压印加工compressing 压缩加工compression bending押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 叠板裁断drawing 引伸加工drawing with ironing抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 摺叠加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending连续弯曲加工progressive blanking连续下料加工progressive drawing连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting 铆接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining无废料加工seaming 折弯重叠加工shaving 缺口修整加工shearing 切断加工sizing 精压加工/矫正加工slitting 割缝加工spinning 卷边?接stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工七.模具常用刀具工作法英语词汇adjustable spanner 活动扳手angle cutter 角铣刀arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手八.模具表面处理英语词汇age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment阿托木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment光辉热处理bypass heat treatment旁路热处理carbide 炭化物carburized case depth浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment磷酸溶液热处理graphitizing 石墨退火。
模具专业的英语词汇大全
模具专业的英语词汇大全一、模具专业英语入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate细水口： pin-point gate 水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate 圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue 热流道板：hot manifold发热管：cartridge heater 探针: thermocouples插头：connector plug 插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity inter-lock顶针：ejector pin 司筒：ejector sleeve司筒针：ejector pin 推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base 上内模：cavity insert下内模：core insert 行位（滑块）： slide镶件：insert 压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar 唧嘴： sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch 扣鸡：parting lock set推杆：push bar 栓打螺丝：S.H.S.B顶板：eracuretun 活动臂：lever arm分流锥：spure sperader 水口司:bush垃圾钉：stop pin 隔片：buffle弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin 销子：dowel pin波子弹弓：ball catch模具成形不良用语英汉对照aberration 色差atomization ?化bank mark ?料纹 bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜low hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形 edge切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔 mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模各种模具常用成形方式英汉对照accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模机械类常用英语：冲压模具-零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块机械类常用英语：冲压模具-模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板冲压模具-冲压名称类英汉对照plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量。
模具专业英语词汇
Injection Mold Technical Terms（一）模具专业基本用词Professional Terms塑料—plastic, resin样件—sample钢料—steel注塑机—injection machine, press产品—part, product, moulding模具—mold, mould, toolA 简易模（样板模）—prototype moldB 量产用模具—production mold 三维造型（数模）—3D model, 3D data二维产品图—2D part drawing设计—design制造—manufacture, build up, construction检验—check, inspection测量—measure, inspection修改—change, modify, correction工程更改—engineer change质量—quality数量—quantity基准—datum, reference牛角入水-rads gate（二）如何解析2D 产品图How to read 2D part drawing产品几何Geometry1．点—point2．线（边）—line, edge3．面faceA 侧面—sideB 表面—surfaceC 外观面—appearance surface 4．壁厚—wall thickness, stock thickness5．加强筋（骨位）—rib6．孔—hole7．细长的槽—slot8．柱位—boss9．角—cornerA 圆角—filletB 倒角—chamferC 尖角—sharp corner 10．斜度—angle, taper11. 凹槽—recess , groove分模信息Splitting分型线—parting line (P/L), splitting line主分模方向—main direction, line of draw浇口设定—gating产品标识Part Identification产品名称—part name (P/N)产品编号+版本号—part number + revision (Rev.)型腔号—cavity number材料标记—material symbol模具编号—mold number (no.)日期印—dating insert, date code循环印—cycling code公司标志—company logo技术要求Specification (Special Requirement)项目启动表Kick-off sheet项目名称—program name, project name产品名称—part name, product name, part description产品编号—part number (P/N)客户模号—customer mold no.项目启动日期—kick off date, start date项目完成日期—due date, lead time内模件用钢—tool steel型腔数量—number of cavities数据文件编号—data file no.注塑材料—resin, plastic, raw material收缩率—shrink, shrinkage, shrink factor注塑机吨位—molding machine size, injection machine size 成型周期—cycle time型腔光洁度—cavity polish型芯光洁度—core polish皮纹（晒纹）—texture, grain拔模斜度—draft angle, removal taper注塑件颜色及光泽—molded color & gloss模具加工地—manufacturing facility热流道供应商—manifold manufacturer, manifold supplier 浇口位置—gate location / position浇口类型—gate type产品标识—stamp information, part identification特殊要求—special instructions安全模数—safe steel产品质量及外观要求Part Quality & Appearance Requirement 尺寸及公差Dimension & Tolerance重要尺寸—critical dimension, important dim., key dim.理论尺寸—nominal dimension实际尺寸—actual dimension公差—tolerance公差带—tolerance range尺寸超差—dimension deviation接受（合格）—accept, OK拒绝（不合格）—reject, refuse, obsolete, NG让步接受—concession, special admit返工—re-work产品缺陷（常见的）Defects (normal)缩水—sink mark, shrinkage飞边，毛边—flash, burr段差—mismatch discrepancy银丝纹，蛇纹—snake marks, streak弯曲，变形—warpage, distortion打不饱（缺料）—short shot熔接线—weld line多胶—unwanted plastic拉伤—damage产品外观Part Appearance产品颜色—part color产品光泽—gloss皮纹粒度—grain常用词汇、词组及短语Normal Word, Short Sentence单边—per side双边—both sides加入，添加—add, incorporate去除，取消—remove, cancel满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet 要求，需要—require, need, demand确认—be approved, agreed by …允许—permit, allow在…范围之内—within不可以，不允许，禁止—free from, prevent, avoid…，除非有另指—… unless otherwise specified…或少于—…or less自动化运作—automatic operation未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.分型线上的飞边（披缝）或段差应小于…Burrs or discrepancy on the P/L shall be … or less.标题栏Title Block产品名称—part name图纸编号+ 版本号（索引号）—drawing no. + level (index)一般公差—general tolerance（三）如何阅读制模标准How to read tooling standard一．模具结构术语Mold Construction TermsA．模架Mold Base模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具高度尺寸（模厚）—stack height of mould③模具重量—total weight of mould, mould thickness定模底板—front plate, top clamping plate, clamp plate, clamping plate定模板—cavity plate, fixed mould plate, A – plate动模板—core plate, moving mould plate, B – plate浮动板—floating plate支撑板—support plate, backing plate间隔板,方铁—support blocks, rails, risers, spacer block顶杆固定板—retaining plate, ejector retaining plate顶板—ejector plate，bottom clamping plate动模底板—back plate导柱—guide pillar, leader pin, guide pin导套—guide bush, leader pin bush复位杆—return pin, push-back pin弹簧—spring撑头—support pillar顶针板导柱、导套—ejection guide pin / bush垃圾钉—stop pin, stop button模脚—standing-off pillars标牌—plaque scutcheonB．成型零部件moulding components型芯—core insert型腔—cavity insert镶针—core pin镶块—sub-insert, split滑块—slide, sliding split斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaftC 斜顶连接块——lifter couplingD 斜顶导向块——lifter guideE 斜顶导滑块——lifter Gib成型顶杆—moulding face pin, form pinC．浇注系统Feed System1．塑料Plastic主流道—sprue分流道runner①主分流道—main runner ②二级分流道—branch runner 分流道断面形状cross-sectional shape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidal浇口gate常用浇口形式normal gate type :①边缘浇口（J型浇口）—edge gate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate潜顶针—subgate to pin④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gate模腔—impression冷料井—cold slug well热流道—hot runner2．模具零件mold components定位圈—locating ring, location ring, register ring浇口套—sprue bush挡圈—stop ring浇口镶块—gate insert热流道板—manifold热嘴—hot dropD．分型面及其锁紧、排气Parting Surface, inter-locking & venting分型线—parting line ( P/L )镶拼线—bodyline, joint line平/ 不平的分型面—flat / non – flat parting surface封胶面—shut off surfaces, seal-off surfaces擦穿位—shut off碰穿位—kiss-off管位—parting line lock分型面的释放(避空) —relief of parting surface分型面的平衡—balancing of parting surface锁紧角度—locking angle锁紧力—clamping force锁模块—safety strap精定位—Interlock, die lock困气—air trap排气槽—vent, vent slot撬模坑--- pry slot计数器--- shot counter/ cycle counterE．滑块机构Slide驱动Actuation①斜导柱—angle pin, horn pin, cam pin②弹簧—spring③油缸—hydraulic cylinder制动Detention①滑块固定器—slide retainer②弹簧制动器—spring-loaded detention (plunger)③挡钉、挡板—stop pin, stop plate, slide stop导轨—gib, guide strip,center guide锁紧块（楔紧块）—heel block, locking heel, wedge block, chase block,slide driver 耐磨片—wear plate, wear strip压板—retainer,gib螺钉—screw定位销—dowel pin行位扣—slide lock / slide retainerflat ejector pin 扁顶针F．斜顶机构Lifter斜顶头—lifter head斜顶杆—lifter rod, lifter shaft斜顶固定块—lifter rod retainer斜顶导向块—lifter guide开口销—split pin固定板（压板）—retainer plate耐磨片—wear plate铜导套—bronze bushing导套固定板—bushing retainer衬套—spacer导轨—L – gib导轨---T-Gib滑动块—slide连接块—U-CouplingG．顶出系统Ejection System基本词汇Basic Word顶出行程—ejection stroke模具开档—daylight粘模—stick on产品脱模—part is push off from, clear part of mould, separation of part 顶板机构Ejector plate assembly顶板—ejector plate顶板固定板—retaining plate推板—stripper plate推板导柱—ejector guide pin推板导套—ejector guide bush撑头—support pillar限位块—stop block,stroke block复位机构Return System复位杆（回程杆）—return pin, push – back pin垃圾钉—stop pin, stop button压簧—compressed spring碟簧— a stack of “Belleville” washers早复位机构—early return system强制复位机构—positive return system顶出方法Ejection Techniques顶杆顶出—pin ejection顶管顶出—sleeve ejection顶块顶出—bar ejection扁顶顶出—blade ejection顶板顶出—stripper ejection油缸顶出—hydraulic ejection气顶—air ejection阀门顶出—valve ejection顶出元件Ejection Elements拉料杆—sprue puller, sucker pin顶杆—ejector pin阶梯式顶杆—stepped ejector pin顶管—ejection sleeve, sleeve扁顶—ejector blade, slabbed off ejector pin顶块—stripper bar顶环—stripper ring推板—stripper plate加速顶—accelerated ejection直顶----straight lifter/EJECTOR BAR顶出辅助机构Supplementary operating system弹簧柱塞器—spring – loaded plunger弹珠定位器—ball catch system插销式锁扣—Latch – lock尼龙拉杆装置—friction puller device电器元件Electric Components压力传感器—pressure transducer限位开关—limit switchF．冷却系统Cooling System基本词汇Basic Word温差—temperature variation水孔（水道）—waterlines, water-ways, flow-way, channel水路—cooling circuit水路示意图—water schematic, schematic circuit冷却液—coolant, coolant fluid内连接—interconnect外连接—external connection出口、入口—outlet、inlet漏水—water leakage水路分布Circuits阶梯式水路—stepped system分隔板水路—baffled hole system斜孔式水路—angled hole system水路元件Components闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male 隔水片—baffle密封圈—O – ring快插水路接头—quick disconnect fitting, quick connection adaptor弯头—elbow偶合器（连接器、接头）—adaptor (including a plug & a socket)橡皮管—rubber hose分水板,集水块—water manifoldG．螺纹、螺纹孔& 螺钉Thread, thread hole & screw螺纹—thread管螺纹—pipe thread螺纹孔—screw hole, tapped hole起吊孔—handling hole, jack screw hole, eye bolt hole螺钉—screw内六角螺钉—socket headed cap screw （）沉头螺钉—flat headed cap screw （）螺栓—bolt螺母—nut锁紧螺母—locknut螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread （BSP）④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread （UNC）⑥美制细螺纹标准—United Fine thread （UNF）H．润滑Lubrication润滑槽—grease groove加油管—grease line油杯—lubrication fitting测量仪器Measuring Instruments游标卡尺—vernier caliper千分尺—micrometer高度规—height gauge刻度规—dial gauge三坐标测量仪（三次元）—Coordinate Measure Machine（CMM）塞规—pin gauge圆角量规—radii gauge轮廓投影机—profile projectorJ．注塑机参数Injection Machine Parameter注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸—hydraulic b．肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force试模工艺参数Moulding Process Parameter, machine setting①时间Timer（TM）, sec注塑（充填）时间—filling time, injection time冷却时间—cooling time补缩时间—packing time保压时间—holding time成型周期—cycle time②速率、速度Velocity, %、speed, in/sec注塑（充填）速度—injection speed保压速率—hold pressure velocity螺杆转速—screw rotation speed③压力Pressure（Prs.）, psi注塑压力—injection pressure保压压力—hold pressure回压（背压）—back pressure④温度Temperature（Temp.）, °F注塑机喷嘴温度—nozzle temp.料筒前段、中段、后段温度—barrel front、middle、rear temp.模温—mould temp.料温—purged resin melt temp.空射料温—air shot melt temp.。
模具专业必要的英语单词
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs.inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接柆键sheet metal parts 冲件plastic parts塑料件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein |刨床miller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager |'depjuti| =vice manager副理section supervisor课长deputy section supervisor =vice section superisor 副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embeded lump|in'bed| |l mp|镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board广告牌feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to. to send delinery back to retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder文件夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count 会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ acceptedparts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供货商质量评估OOBA out of box audit 开箱检查QFD quality function deployment 质量机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂质量AOQL Average Output Quality Level 平均出厂质量Q/R/S Quality/Reliability/Service 质量/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水平等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它质量术语类QCC Quality Control Circle 品质圈QIT Quality Improvement T eam 质量改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM T otal Quality Management 全面质量管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低质量水平RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 质量改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality T arget 质量目标7QCT ools 7 Quality Controll T ools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 质量系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-CompaqS-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 数据中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)标识符SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘驱动器HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算器辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement 4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略质量保证DQA Desigh Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk T op 卧式(机箱)MT Mini-T ower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 扁平电缆PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM T otal Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 操作系统TBA T o Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Sizeugboss模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧销goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架。
模具专业术语
模具专业术语————————————————————————————————作者：————————————————————————————————日期:ﻩ模具专业术语——注塑模(锦浩塑胶模具厂)EngｌisｈTraｉninｇ——Iｎjectｉon Mｏld（一）模具专业基本用词Ｐrofesｓional Ｔeｒms１.塑料—ｐlａstic, resin2．样件—ｓample3. 钢料—sｔeeｌ４. 注塑机—injecｔion mａchine, pｒesｓ５．产品—paｒt, prｏdｕct, mouldiｎg６．模具—mold, moｕlｄ, toolＡ简易模（样板模)—prototype mold Ｂ量产用模具—proｄuctio ｎmｏld7. 三维造型(数模）—modeｌ, 3D dａｔa8．二维产品图—2Ｄparｔdrawing９. 设计—ｄesｉｇn10．制造—ｍanufａcture, build ｕp, construction１1．检验—cheｃk, ｉnｓpeｃtｉｏn12.测量—measｕre，inspecｔion13.修改—chａnge, mｏｄify, ｃoｒrection14. 工程更改—ｅnｇineer cｈange１5．质量—qｕality１６. 数量—quantiｔy17. 基准—ｄａｔuｍ, ｒefeｒｅnｃe（二)如何解析2D 产品图？Ｈow tｏread 2D part drａwing？一. 产品几何Geoｍｅtry1．点—poinｔ2.线（边）—line, ｅdge3.面faｃeA 侧面—siｄｅB 表面—ｓurfaceC 外观面—aｐｐeａrａnｃｅsｕrfａｃe4．壁厚—ｗall thｉｃkneｓs, stoｃk thicknesｓ5．加强筋(骨位）—rib6.孔—hole7．细长的槽—sloｔ8．柱位—boss9.角—coｒnerA 圆角—ｆiｌｌｅｔB 倒角—chaｍferＣ尖角—sharp cｏrnｅr10.斜度—anglｅ，taper1１. 凹槽—rｅceｓs ,groove二. 分模信息Spliｔtiｎｇ1．分型线—parｔing line (Ｐ/L), splitｔiｎg lｉne２. 主分模方向—main directｉon, ｌiｎe of draｗ3．浇口设定—ｇatiｎg三. 产品标识Pａrt Iｄeｎtificａtion1. 产品名称—part nａｍe (Ｐ/N)２.产品编号+版本号—paｒt numbｅr ＋revisioｎ（Rｅv.）3. 型腔号—cａvitｙnuｍber4.材料标记—material symbol5. 模具编号—moｌd numbeｒ(no.）6．日期印—ｄatingｉnserｔ, date code7. 循环印—ｃycｌiｎg code8.公司标志—coｍpany loｇo四. 技术要求Sｐecificatioｎ(SpｅciaｌRｅquiｒement)1.项目启动表Kｉcｋ-ofｆshｅｅt１）项目名称—progrａｍname,projｅct naｍe2)产品名称—part namｅ, pｒoduct ｎame, part descriptｉｏn３) 产品编号—ｐart ｎuｍbeｒ(P/N)4) 客户模号—cｕstoｍer mold no.5) 项目启动日期— kick off dａtｅ，starｔdatｅ6)项目完成日期— duｅ dａte, lead tｉｍｅ7) 内模件用钢—ｔool sｔｅｅｌ8）型腔数量—numｂer of cavit iｅs９)数模文件编号—data.10）注塑材料—rｅsin，plastic, raw maｔｅrial1１）收缩率—ｓhrink, ｓhrinkage,sｈrink ｆactoｒ12)注塑机吨位—ｍoldｉng mａchine sｉzｅ， injeｃｔｉon machiｎe size １３）成型周期—cyｃle time14)型腔光洁度—caｖiｔy pｏlish1５) 型芯光洁度—core polｉｓh16）皮纹(晒纹)—tｅxｔurｅ, gｒain17）拔模斜度—dｒaft anｇle, ｒemoval ｔaper18）注塑件颜色及光泽—molｄeｄｃｏｌoｒ& ｇloss19) 模具加工地—manｕfａｃturing ｆaｃility２０）热流道供应商—maniｆｏｌd mａnuｆactureｒ, ｍａｎifolｄ supplieｒ2１)浇口位置—gaｔe ｌoｃation ／pｏｓitｉon22) 浇口类型—gａtｅtype23) 产品标识—stamp infｏrmaｔion, parｔidentificａtion２４）特殊要求—sｐeciaｌ instructiｏｎs2. 产品质量及外观要求Pａrt Quality & Apｐｅaraｎcｅ１）尺寸及公差Dｉmensioｎ&Toｌｅｒancｅ①重要尺寸—ｃritical dimensｉoｎ,importanｔdiｍ.，kｅy dim.②理论尺寸—ｎｏｍiｎalｄimension③实际尺寸—actuａｌdiｍension④公差—tolｅraｎce⑤公差带—tｏlｅrancｅrａnge⑥尺寸超差—dimensionｄeviａtion⑦接受（合格）—ａccepｔ, OＫ⑧拒绝(不合格）—rejecｔ, refｕse,oｂsolete,NＧ⑨让步接受—conceｓsion, ｓｐecial adｍiｔ⑩返工—re-wｏrk２）产品缺陷（较常见）Ｄefeｃts (normaｌ）①缩印—sｉnk mark, sｈrｉｎｋage②飞边—flａsh, burr③段差—mｉsmａtcｈｄｉｓcｒepancy④银丝纹—ｓｎake ｍaｒks, streak⑤弯曲—warpａｇe, ｄistoｒtion⑥打不足（缺料）—shorｔｓhot⑦熔接线—wｅld lｉne3．产品外观ParｔAｐｐearanｃｅ①产品颜色—paｒｔｃｏｌor②产品光泽—ｇloss③皮纹粒度—gｒain4．常用词汇、词组及短语NormａｌＷｏrd, Shｏｒt Seｎｔｅｎｃe1）单边—per side2)双边—both sides３) 加入,添加—aｄｄ,iｎcorporａtｅ４) 去除，取消—rｅmovｅ,ｃancel５) 满足…的要求,符合,与…要求一致—accｏｒｄing ｔｏ, conｆorｍto, satisfy, mｅeｔ6) 要求，需要—ｒequｉrｅ,neｅｄ,demanｄ7）确认—be ａｐproｖｅｄ, agreedｂy …8) 允许—peｒmｉｔ，ａlloｗ9) 在…范围之内—ｗithin1０）不可以,不允许，禁止—free from，preｖent, avｏid11）…,除非有另指—…unleｓsｏtherwｉｓｅspecified1２）…或少于—…or ｌess13) 自动化运作—automatiｃoperａｔｉoｎ１4）未注尺寸(详细形状）见三维造型Noｎｄimensioned ｃontｏur (dｅｔａiled ｓhape) ｓｅe ３D mｏｄel.15)分型线上的飞边(披缝)或段差应小于…Bｕrrs and diｓｃrｅpａｎcy onｔheＰ／Ｌshaｌl be… ｏr less.五．标题栏Titｌe Bloｃｋ１. 产品名称—part name２．图纸编号+ 版本号(索引号）—draｗｉng no．+ level （ｉndex)3. 一般公差[的标准] —generａl tolerａnｃe（三) 如何阅读制模标准？Hｏw to read toｏling stanｄaｒd?一．模具结构术语Moｌd CｏnsｔrｕctiｏｎTermiｎologyA．模架Mold Ｂａｓe1.模架量化特征Mｅasuremｅnt Feature①长X 宽Ｘ高—ＬeｎgtｈXＷidth X Height②模具推高尺寸（模厚）—sｔａck hｅiｇht ｏf ｍould③模具重量—totａl weight ofｍould,mouｌd thｉｃkｎesｓ2. 定模底板—fｒont pｌaｔe, ｔｏｐclamｐiｎｇplａte, cｌamｐpｌatｅ，clａmｐinｇplate３．定模板—cａvｉty plａｔe，fixｅd moｕlｄplａte, A – platｅ4. 动模板—cｏｒe plａｔe,ｍoｖing mｏｕｌd ｐlate, B – plate５. 支撑板—ｓuppｏｒt plａte, baｃking ｐlate6. 模脚—support bloｃks，raｉlｓ，riseｒs, spａｃeｒblｏｃk７. 顶杆固定板—reｔaining ｐｌatｅ, ejector retainｉｎg plate８. 顶板—ejｅctor ｐlaｔe9．动模底板—baｃｋpｌａte1０．导柱—ｇｕｉde ｐillar, leａｄer pin, ｇuｉdeｐin11．导套—gｕidｅｂuｓh, ｌeadｅr ｐｉnｂush12.复位杆—rｅturn piｎ，push-back ｐｉｎ13．弹簧—ｓpriｎｇ14. 撑头—supｐｏrt pillar１5．推板导柱、导套—ejectiｏn gｕidｅpｉn / ｂush16．挡钉—ｓtop ｐiｎ,stoｐ buttoｎ１７．站立脚—sｔａndiｎg-ofｆpiｌlars18．标牌—pｌaquｅscutcheonB.成型零部件moｕｌding components1９. 型芯—cｏre20．型腔—cavitｙ２1. 镶针—core ｐin２２. 镶块—insｅrt，sｐlit23.滑块—sｌide, sliｄiｎｇsｐlit２4. 斜顶—lifteｒ,angled-liｆt ｓｐlitA 斜顶头—lｉftｅr hｅadB 斜顶杆—ｌifter rod, lｉｆteｒｓｈａft2５. 成型顶杆—ｍoulding facｅpin, form pｉｎC．浇注系统Fｅed System1．塑料Mouldingａ．主流道—ｓｐrueｂ. 分流道runｎer①主分流道— mａin ruｎner ②二级分流道— braｎcｈ rｕnｎeｒ分流道断面形状cｒosｓ-sｅｃtional ｓｈape oｆｒunner①圆形—ｆuｌl roｕｎd②半圆形—semiciｒcｕｌar③梯形—trapｅｚoidaｌｃ．浇口gaｔｅ常用浇口形式nｏrmａl ｇate tyｐe :①边缘浇口（J型浇口) —eｄgｅｇate, J –ｇate②侧浇口—side gate③潜伏式浇口—sub-gaｔe, ｃａshew gatｅ， subsurfａｃｅ gaｔe, suｂmaｒine gaｔe④潜伏式二次浇口(隧道式浇口) —ｔunnｅl gａｔe ontｏfeｅｄer post⑤点浇口—pｉn gａｔe⑥直接浇口(主流道型浇口) —ｓprue gate, direct gａte⑦护耳式浇口—tａb gａted. 模腔—imprｅｓsｉｏnｅ. 冷料井—colｄsｌug welｌf．热流道—hot runner２.模具零件moｌｄcoｍponentsa. 定位圈—lｏｃating ring, lｏｃation ｒing, regｉsｔｅr riｎｇb. 浇口套—spｒue bushc．挡圈—sｔｏp ｒingd．浇口镶块—gate inｓeｒte．热流道板—mａｎifoldｆ. 热嘴—ｈｏｔｄropＤ.分型面及其锁紧、排气Paｒtｉｎg Sｕrfaｃｅ, inter-loｃking＆ventｉng 1．分型线—paｒtｉnｇline ( P/Ｌ）２. 镶拼线—bｏdｙlｉnｅ，ｊoiｎt lｉne3．平/不平的分型面—ｆlａt ／non – flaｔ pａrting sｕrface4．封胶面—sｈut ofｆsurfaces, ｓeａｌ－ｏff suｒfａceｓ5．擦位—shuｔoff6. 碰穿位—kiｓs-ｏff7. 管位—pａrtｉｎgｌinｅｌock８.分型面的释放(避空) —rｅｌieｆｏｆpａｒtiｎg ｓuｒｆａｃe９．分型面的平衡—bａlanｃiｎｇof ｐarｔing ｓurface10．锁紧角度—ｌockｉng anglｅ1１.锁紧力—cｌａｍpingｆoｒce1２．锁模板—safetｙstｒap1３．精定位—Inｔeｒloｃk,die locｋ14．困气—aｉｒtrap1５．排气槽—vent, veｎt ｓlｏtＥ.滑块机构Slide１．驱动Acｔuaｔｉｏｎ①斜导柱—anglｅｄｐin, ｈorn pｉn, cａm pin②弹簧—sprinｇ③油缸—ｈydraulｉc cyliｎder２．制动Dｅｔeｎtion①滑块固定器—sｌide rｅtａｉｎer②弹簧制动器—spｒing-loaded detentｉon (plunger)③挡钉、挡板—ｓtop pin, stop platｅ, slide stop3．导轨—gｉｂ,gｕide sｔrip4．锁紧块(楔紧块)—heel blｏcｋ,ｌｏcking ｈｅel，wｅｄge blｏｃk, cｈasｅbl ｏｃk5. 耐磨片—wear pｌａte，ｗｅar strip6. 压板—reｔaiｎeｒ7. 螺钉—screw８．定位销—dowelＦ.斜顶机构Ｌiftｅｒ1.斜顶头—lｉfｔｅｒｈeａｄ2．斜顶杆—liｆtｅr roｄ，lifｔer ｓhａfｔ3．开口销—spｌit ｐin4．固定板(压板) —reｔaiｎer plａｔｅ5. 耐磨片—wear ｐlatｅ６. 铜导套—ｂrｏnzｅbuｓhing7．衬套—spaｃeｒ８. 导轨—L – gib9. 滑动块—slideG．顶出系统EjectioｎSyｓtem１. 基本词汇Baｓｉc Worｄ①顶出行程—ejectｉｏn stroke②模具开档—ｄayligｈt③粘模—stｉck④产品脱模—part iｓpuｓh ofｆfrom,ｃlearｐart of mouｌd, seｐaratioｎofｐart2. 顶板机构Ejector pｌａｔe asｓembly①顶板(推板) —ｅｊｅｃｔoｒplａtｅ②顶板固定板—retａiniｎg plａte③推板导柱—ejector gｕiｄｅpin④推板导套—ｅjｅctor guide ｂusｈ⑤撑头—supｐort pｉllar, pilｌarｓupport3．复位机构Return Sｙsteｍ①复位杆(回程杆)—return ｐin，ｐush – back pin②挡钉—sｔｏｐpin, sｔop buｔton③压簧—coｍpｒｅsｓeｄsｐring④碟簧—a sｔack of “Ｂeｌleviｌｌｅ”wasｈers⑤早复位机构—ｅａrly return sｙsｔem⑥强制复位机构—posｉtｉve retｕrｎsｙsteｍ4．顶出方法Ejection Techniqｕes１) 顶杆顶出—ｐiｎeｊection２) 顶管顶出—ｓleｅve ejｅction3）顶块顶出—bａr ejｅction４) 扁顶顶出—bｌａde ｅｊｅction５) 顶板顶出—ｓtripper eｊecｔｉon６) 油缸顶出—hydraｕlic ejｅctｉｏn7) 气顶—air ｅjectioｎ8）阀门顶出—valve ejｅｃtion5. 顶出元件Ejecｔｉon Eｌｅments1) 拉料杆—spｒue pｕｌlｅr，sｕckerｐin2) 顶杆—ejector pｉｎ3) 阶梯式顶杆—ｓｔeppｅd eｊｅctor ｐin4) 顶管—eｊeｃtion sleｅｖe，slｅevｅ５）扁顶—ｅjｅcｔor blaｄe, slａbｂeｄoff ejecｔｏr pin6）顶块—striｐper bar7）顶环—strippｅr ｒing８)推板—ｓtripper plate9)加速顶—accｅleｒaｔｅd ejeｃtioｎ6. 顶出辅助机构Supｐlｅmｅntaryｏpｅraｔｉng sysｔem1）弹簧柱塞器—sprｉnｇ–ｌoａdｅｄｐｌunger２）弹珠定位器—baｌl catch ｓyｓtem3) 插销式锁扣—Lａtch– lock4) 尼龙拉杆装置—fｒiｃtion pullｅr ｄeｖice７．电器元件Electrｉc Coｍpｏnents1) 压力传感器—pｒessuｒe trａｎｓduｃer2) 限位开关—ｌimit swｉtchF．冷却系统Ｃooling Ｓysｔem1. 基本词汇BａsiｃWｏrd１)温差—teｍｐerａture variａtion2) 水孔（水道）—ｗaｔｅrｌines, wａtｅr-waｙｓ, flｏw-wａy, cｈannel3) 水路—ｃｏolｉng ciｒcuit4) 水路示意图—wateｒsｃhｅmａtｉc，ｓchematic circuit5) 冷却液—cｏｏlaｎt，coｏlant fluid６）内连接—iｎｔercｏnnｅct7) 外连接—eｘteｒnaｌｃｏｎnectioｎ8）出口、入口—oｕtlｅt、iｎleｔ9) 漏水—ｗａter ｌeakage2. 水路分布Circｕits1)阶梯式水路—steppeｄsyｓteｍ２)喷淋—bａffled holeｓｙstem3) 斜孔式水路—angled hole sｙｓtem3. 水路元件Ｃoｍｐonents1）闷头（螺塞、止水栓) — (threａdlesｓ)brasｓpressure pｌuｇ:feｍale plug & male2）隔水片—bafflｅ3) 密封圈—O – rinｇ4）快插水路接头—ｑuick disconｎｅcｔｆｉｔtinｇ, qｕick coｎneｃｔi ｏｎadaptor5) 弯头—elｂｏｗ６)偶合器（连接器、接头) —adapｔor （iｎcｌｕding a plug & a sｏcket）7）橡皮管—rubbｅｒｈoｓｅ８)分水板—water mａnｉｆolｄG.螺纹、螺纹孔& 螺钉Tｈread,tｈｒead ｈole & ｓcrｅｗ1．螺纹—threａd２. 管螺纹—pipe thｒeaｄ3．螺纹孔—screｗｈｏｌe, tappｅd hｏle4. 起吊孔—ｈandｌｉｎg holｅ, jack scｒｅw hole, eyｅbolt hole５.螺钉—screw6．内六角螺钉—sockeｔheａded cap sｃrｅｗ（s．h.c.s.）7．沉头螺钉—ｆlat headed ｃaｐscrew （f．ｈ.c.s）８. 螺栓—bｏlｔ, eyｅbｏｌｔ9．螺母—ｎuｔ10.锁紧螺母—lｏcknut１1．螺纹标准Tｈｒead Stａｎdａrd①公制标准—Metric②英制标准—Imｐｅｒｉal③英制管螺纹标准—Bｒiｔｉsh Ｓtａndard Ｐｉpe thread （BSP)④美制管螺纹标准—ＮPＴ⑤美制粗螺纹标准—UｎitｅｄCoarse tｈｒeａｄ（UNＣ）⑥美制细螺纹标准—Ｕnｉted Fｉnｅtｈrｅａd（ＵNＦ）H．润滑Ｌubricatiｏn１．润滑槽—greａｓe grooｖe２．加油管—grｅａsｅlｉｎe3．油杯—luｂriｃａtioｎfittｉngI．测量仪器Ｍｅasuring Iｎsｔrｕmｅntｓ1. 游标卡尺—vernierｃaliper2. 千分尺—ｍicrｏmeter3.高度规—ｈeｉght gauｇｅ４. 刻度规—ｄiａｌｇａuge5．三坐标测量仪—Coordinaｔe Ｍeasuｒe Maｃhiｎｅ（CＭM）6．塞规—piｎgauge７．圆角量规—radii gauｇe8．輪廓投影機—proJ.注塑机参数Ｉｎjectｉon MacｈｉｎｅPａrameter1. 注塑机规格参数Ｉｎjecｔiｏn MachineＳpeｃifｉｃation①锁紧类型ｃlamp typea.油缸—hydｒauｌic ｂ．肘杆式—togｇle②垂直注塑机导柱间距—tie baｒverticalｃlｅarance③水平注塑机导柱间距—tie bar hoｒizonｔａlｃｌearancｅ④台板尺寸—platenｄim.⑤最小/最大模厚—molｄheighｔMiｎ. / Mａx., Min./ Max. moldｔhickｎess⑥最小／最大注塑机开档—ｏpen daｙliｇht Min. ／Max.⑦锁紧行程—ｃlamｐsｔroke⑧锁紧力—clampｉng forｃe⑨顶出行程—ejector stroke⑩顶出力—ejector forｃe２. 试模工艺参数Mouｌdiｎg ProcessＰaｒameter，macｈine setting①时间Ｔimer(TM)，seca. 注塑(充填）时间—fｉｌling time, iｎjｅctｉon timeb．冷却时间—cｏolｉnｇtimec. 补缩时间—ｐacｋinｇtimｅｄ.保压时间—holding ｔiｍee. 成型周期—cyｃｌe time②速率、速度Ｖelocｉｔy, ％、spｅed，in/seca．注塑（充填)速度—iｎjectiｏn sｐｅedb．保压速率—ｈｏld pressure velocitｙc．螺杆转速—screw rotatioｎｓｐeed③压力Pressｕｒe(Ｐrs．), psiａ. 注塑压力—ｉｎｊeｃtioｎpressurｅb. 保压压力—ｈoｌd prｅssuｒec．回压(背压）—bａｃk prｅｓsure④温度Temｐeratｕre(Teｍp．）, °Fa．注塑机喷嘴温度—nｏzzlｅｔｅmp.b．料筒前段、中段、后段温度—barrel ｆrｏnt、middle、rear temp.c．模温—mouldｔemp.d．料温—purgｅd resin melt ｔemp．ｅ．空射料温—air sｈot melt tｅmｐ.。
模具专业的英语词汇大全
模具专业的英语词汇大全一、模具基础词汇1. Mold 模具2. Die 冲模3. Core 核心模4. Cavity 型腔5. Mold Base 模架6. Mold Steel 模具钢7. Runner 流道8. Gate 进浇口9. Ejector Pin 顶针10. Ejector Plate 顶板二、模具设计相关词汇1. Draft Angle 脱模斜度2. Parting Line 分模线3. Radius 圆角4. Undercut 难以脱模的凹槽5. Slide 滑块6. Lifters 顶杆7. Cooling Channel 冷却水道8. Injection Point 注射点9. Shrinkage 收缩率10. Molding Cycle 成型周期三、模具加工与维护词汇1. Machining 加工2. Milling 铣削3. Grinding 磨削4. EDM (Electrical Discharge Machining) 电火花加工5. Wire Cutting 线切割6. Polishing 抛光7. Assembly 装配8. Maintenance 维护9. Repair 修理10. Replacement 更换四、模具材料与热处理词汇1. Tool Steel 工具钢2. Stainless Steel 不锈钢3. Aluminum 铝4. Plastic 塑料5. Rubber 橡胶6. Heat Treatment 热处理7. Hardness 硬度8. Tempering 回火9. Quenching 淬火10. Annealing 退火五、模具行业相关词汇1. Mold Maker 模具师傅2. Mold Designer 模具设计师3. Mold Manufacturer 模具制造商4. Injection Molding 注塑成型5. Blow Molding 吹塑成型6. Compression Molding 压缩成型7. Transfer Molding 传递成型8. Prototype Model 原型模具9. Mass Production 批量生产10. Quality Inspection 质量检验六、模具测试与质量控制词汇1. First Article Inspection 首件检查2. Sample 样品3. Defect 缺陷4. Dimensional Accuracy 尺寸精度5. Tolerance 公差6. Surface Finish 表面光洁度7. Stress Analysis 应力分析8. Flow Analysis 流动分析9. Mold Flow Simulation 模具流动模拟10. Quality Control 质量控制七、模具行业常用设备词汇1. Injection Molding Machine 注塑机2. Extruder 挤出机3. Blow Molding Machine 吹塑机4. CNC Machine 数控机床5. Lathe 车床6. Milling Machine 铣床7. Grinder 磨床8. EDM Machine 电火花机床9. Laser Cutter 激光切割机10. Robot 自动化八、模具生产流程词汇1. Design Drawing 设计图纸2. Mold Construction 模具构建3. Machining Process 加工工艺4. Tooling Setup 模具安装5. Trial Run 试模6. Adjustment 调整7. Production Run 生产运行8. Mold Maintenance 模具保养9. Mold Modification 模具修改10. Mold Recycling 模具回收九、模具行业认证与标准词汇1. ISO Certification ISO认证2. Quality Management System 质量管理体系3. Standard 标准化4. DIN 德国工业标准5. ASTM 美国材料与试验协会6. JIS 日本工业标准7. Certification Body 认证机构8. Audit 审核检查9. Compliance 符合性10. Continuous Improvement 持续改进十、模具行业发展趋势词汇1. Automation 自动化2. Intelligent Manufacturing 智能制造3. 3D Printing 三维打印4. Rapid Prototyping 快速原型5. Industry 4.0 工业4.06. Internet of Things (IoT) 物联网7. Big Data 大数据8. Cloud Computing 云计算9. Sustainable Development 可持续发展10. CrossIndustry Integration 跨行业整合通过这些词汇，我们可以看到模具行业不仅涉及具体的技术和操作，还包括了管理、质量控制、认证以及未来的发展趋势。
模具专业英语词汇
Injection Mold Technical Terms(一)模具专业基本用词Professional Terms1.塑料—plastic, resin2.样件—sample3.钢料—steel4.注塑机—injection machine, press5.产品—part, product, moulding6.模具—mold, mould, toolA 简易模(样板模)—prototype moldB 量产用模具—production mold7.三维造型(数模)—3D model, 3D data8.二维产品图—2D part drawing9.设计—design10.制造—manufacture, build up, construction11.检验—check, inspection12.测量—measure, inspection13.修改—change, modify, correction14.工程更改—engineer change15.质量—quality16.数量—quantity17.基准—datum, reference牛角入水-rads gate(二)如何解析2D 产品图?How to read 2D part drawing?一.产品几何Geometry1.点—point2.线(边)—line, edge3.面faceA 侧面—sideB 表面—surfaceC 外观面—appearance surface4.壁厚—wall thickness, stock thickness5.加强筋(骨位)—rib6.孔—hole7.细长的槽—slot8.柱位—boss9.角—cornerA 圆角—filletB 倒角—chamferC 尖角—sharp corner10.斜度—angle, taper11. 凹槽—recess , groove第 1 页共11 页二.分模信息Splitting1.分型线—parting line (P/L), splitting line2.主分模方向—main direction, line of draw3.浇口设定—gating产品标识Part Identification1.产品名称—part name (P/N)2.产品编号+版本号—part number + revision (Rev.)3.型腔号—cavity number4.材料标记—material symbol5.模具编号—mold number (no.)6.日期印—dating insert, date code7.循环印—cycling code8.公司标志—company logo三.技术要求Specification (Special Requirement)1.项目启动表Kick-off sheet1)项目名称—program name, project name2)产品名称—part name, product name, part description3)产品编号—part number (P/N)4)客户模号—customer mold no.5)项目启动日期—kick off date, start date6)项目完成日期—due date,lead time7)内模件用钢—tool steel8)型腔数量—number of cavities9)数据文件编号—data file no.10)注塑材料—resin, plastic, raw material11)收缩率—shrink, shrinkage, shrink factor12)注塑机吨位—molding machine size, injection machine size13)成型周期—cycle time14)型腔光洁度—cavity polish15)型芯光洁度—core polish16)皮纹(晒纹)—texture, grain17)拔模斜度—draft angle, removal taper18)注塑件颜色及光泽—molded color & gloss19)模具加工地—manufacturing facility20)热流道供应商—manifold manufacturer, manifold supplier21)浇口位置—gate location / position22)浇口类型—gate type23)产品标识—stamp information, part identification24)特殊要求—special instructions25)安全模数—safe steel2.产品质量及外观要求Part Quality & Appearance Requirement1)尺寸及公差Dimension & Tolerance①重要尺寸—critical dimension, important dim., key dim.②理论尺寸—nominal dimension③实际尺寸—actual dimension④公差—tolerance⑤公差带—tolerance range⑥尺寸超差—dimension deviation⑦接受(合格)—accept, OK⑧拒绝(不合格)—reject, refuse, obsolete, NG⑨让步接受—concession, special admit⑩返工—re-work2)产品缺陷(常见的)Defects (normal)①缩水—sink mark, shrinkage②飞边,毛边—flash, burr③段差—mismatch discrepancy④银丝纹,蛇纹—snake marks, streak⑤弯曲,变形—warpage, distortion⑥打不饱(缺料)—short shot⑦熔接线—weld line⑧多胶—unwanted plastic⑨拉伤—damage3.产品外观Part Appearance①产品颜色—part color②产品光泽—gloss③皮纹粒度—grain4.常用词汇、词组及短语Normal Word, Short Sentence1)单边—per side2)双边—both sides3)加入,添加—add, incorporate4)去除,取消—remove, cancel5)满足…的要求,符合,与…要求一致—according to, conform to, satisfy, meet6)要求,需要—require, need, demand7)确认—be approved, agreed by …8)允许—permit, allow9)在…范围之内—within10)不可以,不允许,禁止—free from, prevent, avoid11)…,除非有另指—…unless otherwise specified12)…或少于—…or less13)自动化运作—automatic operation14)未注尺寸(详细形状)见三维造型Non dimensioned contour (detailed shape) see 3D model. 15)分型线上的飞边(披缝)或段差应小于…Burrs or discrepancy on the P/L shall be … or less.四.标题栏Title Block1.产品名称—part name2.图纸编号 + 版本号(索引号)—drawing no. + level (index)3.一般公差—general tolerance(三)如何阅读制模标准?How to read tooling standard?一.模具结构术语Mold Construction TermsA.模架Mold Base1.模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具高度尺寸(模厚)—stack height of mould③模具重量—total weight of mould, mould thickness2.定模底板—front plate, top clamping plate, clamp plate, clamping plate3.定模板—cavity plate, fixed mould plate, A – plate4.动模板—core plate, moving mould plate, B – plate5.浮动板—floating plate6.支撑板—support plate, backing plate7.间隔板,方铁—support blocks, rails, risers, spacer block8.顶杆固定板—retaining plate, ejector retaining plate9.顶板—ejector plate,bottom clamping plate10.动模底板—back plate11.导柱—guide pillar, leader pin, guide pin12.导套—guide bush, leader pin bush13.复位杆—return pin, push-back pin14.弹簧—spring15.撑头—support pillar16.顶针板导柱、导套—ejection guide pin / bush17.垃圾钉—stop pin, stop button18.模脚—standing-off pillars19.标牌—plaque scutcheonB.成型零部件moulding components20.型芯—core insert21.型腔—cavity insert22.镶针—core pin23.镶块—sub-insert, split24.滑块—slide, sliding split25.斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaftC 斜顶连接块——lifter couplingD 斜顶导向块——lifter guideE 斜顶导滑块——lifter Gib26.成型顶杆—moulding face pin, form pinC.浇注系统Feed System1.塑料Plastica.主流道—sprueb.分流道runner①主分流道—main runner②二级分流道—branch runner分流道断面形状cross-sectional shape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidalc.浇口gate常用浇口形式normal gate type :①边缘浇口(J型浇口)—edge gate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate潜顶针—subgate to pin④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gated.模腔—impressione.冷料井—cold slug wellf.热流道—hot runner2.模具零件mold componentsa.定位圈—locating ring, location ring, register ringb.浇口套—sprue bushc.挡圈—stop ringd.浇口镶块—gate inserte.热流道板—manifoldf.热嘴—hot dropD.分型面及其锁紧、排气Parting Surface, inter-locking & venting1.分型线—parting line ( P/L )2.镶拼线—bodyline, joint line3.平/ 不平的分型面—flat / non – flat parting surface4.封胶面—shut off surfaces, seal-off surfaces5.擦穿位—shut off6.碰穿位—kiss-off7.管位—parting line lock8.分型面的释放(避空) —relief of parting surface9.分型面的平衡—balancing of parting surface10.锁紧角度—locking angle11.锁紧力—clamping force12.锁模块—safety strap13.精定位—Interlock, die lock14.困气—air trap15.排气槽—vent, vent slot16.撬模坑--- pry slot17.计数器--- shot counter/ cycle counterE.滑块机构Slide1.驱动Actuation①斜导柱—angle pin, horn pin, cam pin②弹簧—spring③油缸—hydraulic cylinder2.制动Detention①滑块固定器—slide retainer②弹簧制动器—spring-loaded detention (plunger)③挡钉、挡板—stop pin, stop plate, slide stop3.导轨—gib, guide strip,center guide4.锁紧块(楔紧块)—heel block, locking heel, wedge block, chase block,slide driver5.耐磨片—wear plate, wear strip6.压板—retainer,gib7.螺钉—screw8.定位销—dowel pin9.行位扣—slide lock / slide retainer10. flat ejector pin 扁顶针F.斜顶机构Lifter1.斜顶头—lifter head2.斜顶杆—lifter rod, lifter shaft3.斜顶固定块—lifter rod retainer4.斜顶导向块—lifter guide5.开口销—split pin6.固定板(压板)—retainer plate7.耐磨片—wear plate8.铜导套—bronze bushing9.导套固定板—bushing retainer10.衬套—spacer11.导轨—L – gib12.导轨---T-Gib13.滑动块—slide14.连接块—U-CouplingG.顶出系统Ejection System1.基本词汇Basic Word①顶出行程—ejection stroke②模具开档—daylight③粘模—stick on④产品脱模—part is push off from, clear part of mould, separation of part2.顶板机构Ejector plate assembly①顶板—ejector plate②顶板固定板—retaining plate③推板—stripper plate④推板导柱—ejector guide pin⑤推板导套—ejector guide bush⑥撑头—support pillar⑦限位块—stop block,stroke block3.复位机构Return System①复位杆(回程杆)—return pin, push – back pin②垃圾钉—stop pin, stop button③压簧—compressed spring④碟簧—a stack of ―Belleville‖ washers⑤早复位机构—early return system⑥强制复位机构—positive return system4.顶出方法Ejection Techniques1)顶杆顶出—pin ejection2)顶管顶出—sleeve ejection3)顶块顶出—bar ejection4)扁顶顶出—blade ejection5)顶板顶出—stripper ejection6)油缸顶出—hydraulic ejection7)气顶—air ejection8)阀门顶出—valve ejection5.顶出元件Ejection Elements1)拉料杆—sprue puller, sucker pin2)顶杆—ejector pin3)阶梯式顶杆—stepped ejector pin4)顶管—ejection sleeve, sleeve5)扁顶—ejector blade, slabbed off ejector pin6)顶块—stripper bar7)顶环—stripper ring8)推板—stripper plate9)加速顶—accelerated ejection10)直顶----straight lifter/EJECTOR BAR6.顶出辅助机构Supplementary operating system1)弹簧柱塞器—spring – loaded plunger2)弹珠定位器—ball catch system3)插销式锁扣—Latch – lock4)尼龙拉杆装置—friction puller device7.电器元件Electric Components1)压力传感器—pressure transducer2)限位开关—limit switchF.冷却系统Cooling System1.基本词汇Basic Word1)温差—temperature variation2)水孔(水道)—waterlines, water-ways, flow-way, channel3)水路—cooling circuit4)水路示意图—water schematic, schematic circuit5)冷却液—coolant, coolant fluid6)内连接—interconnect7)外连接—external connection8)出口、入口—outlet、inlet9)漏水—water leakage2.水路分布Circuits1)阶梯式水路—stepped system2)分隔板水路—baffled hole system3)斜孔式水路—angled hole system3.水路元件Components1)闷头(螺塞、止水栓)—(threadless)brass pressure plug : female plug & male2)隔水片—baffle3)密封圈—O – ring4)快插水路接头—quick disconnect fitting, quick connection adaptor5)弯头—elbow6)偶合器(连接器、接头)—adaptor (including a plug & a socket)7)橡皮管—rubber hose8)分水板,集水块—water manifoldG.螺纹、螺纹孔& 螺钉Thread, thread hole & screw1.螺纹—thread2.管螺纹—pipe thread3.螺纹孔—screw hole, tapped hole4.起吊孔—handling hole, jack screw hole, eye bolt hole5.螺钉—screw6.内六角螺钉—socket headed cap screw (s.h.c.s.)7.沉头螺钉—flat headed cap screw (f.h.c.s)8.螺栓—bolt9.螺母—nut10.锁紧螺母—locknut11.螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread (BSP)④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread (UNC)⑥美制细螺纹标准—United Fine thread (UNF)H.润滑Lubrication1.润滑槽—grease groove2.加油管—grease line3.油杯—lubrication fittingI.测量仪器Measuring Instruments1.游标卡尺—vernier caliper2.千分尺—micrometer3.高度规—height gauge4.刻度规—dial gauge5.三坐标测量仪(三次元)—Coordinate Measure Machine(CMM)6.塞规—pin gauge7.圆角量规—radii gauge8.轮廓投影机—profile projectorJ.注塑机参数Injection Machine Parameter1.注塑机规格参数Injection Machine Specification①锁紧类型clamp typea.油缸—hydraulicb.肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force2.试模工艺参数Moulding Process Parameter, machine setting①时间Timer(TM), seca.注塑(充填)时间—filling time, injection timeb.冷却时间—cooling timec.补缩时间—packing timed.保压时间—holding timee.成型周期—cycle time②速率、速度Velocity, %、speed, in/seca.注塑(充填)速度—injection speedb.保压速率—hold pressure velocityc.螺杆转速—screw rotation speed③压力Pressure(Prs.), psia.注塑压力—injection pressureb.保压压力—hold pressurec.回压(背压)—back pressure④温度Temperature(Temp.), °Fa.注塑机喷嘴温度—nozzle temp.b.料筒前段、中段、后段温度—barrel front、middle、rear temp.c.模温—mould temp.d.料温—purged resin melt temp.e.空射料温—air shot melt temp. 第11 页共11 页。
模具专业词汇中英文对照表
模具专业词汇中英文对照表1. 模具材料（Mould Materials）•合金钢（Alloy Steel）•不锈钢（Stnless Steel）•工具钢（Tool Steel）•铸造铁（Cast Iron）•铝合金（Aluminum Alloy）•铜合金（Copper Alloy）•硅橡胶（Silicone Rubber）•塑料（Plastic）•陶瓷（Ceramic）2. 模具零件（Mould Components）•模板（Mold Base）•注塑装置（Injection Unit）•顶出器（Ejector）•气嘴（Nozzle）•间隙（Clearance）•提位器（Lifter）•滑块（Slide）•定位圈（Locating Ring）•膜背（Backing Plate）•挡块（Stop Block）•压板（Clamp Plate）•冷却管（Coolant Pipe）•驱动装置（Drive Unit）3. 模具制造工艺（Mould Manufacturing Process）•设计（Design）•切割（Cutting）•加工（Machining）•组装（Assembly）•调试（Debugging）•精修（Finishing）•表面处理（Surface Treatment）•检查（Inspection）•试产（Trial Production）4. 模具加工方式（Mould Processing Methods）•铣削（Milling）•磨削（Grinding）•拉刀（Planing）•镗削（Boring）•钻孔（Drilling）•线切割（Wire Cutting）•抛光（Polishing）•火花加工（EDM）5. 模具设计要点（Key Points in Mold Design）•壁厚（Wall Thickness）•浇注系统（Gating System）•冷却系统（Cooling System）•排气（Venting）•气罩（Bubbler）•顶杆（Ejector Pin）•脱模斜度（Draft Angle）•零件坯料与尺寸（Blank and Dimensions）•对位方式（Alignment Method）•衬套（Insert）•翻制（Flip Mold）•分模（Split Mold）6. 模具维护与保养（Mold Mntenance）•模具清洁（Mold Cleaning）•润滑（Lubrication）•排浆（Purging）•磨损修复（Wear Repr）•抛光修复（Polish Repr）•零件更换（Component Replacement）•修复记录（Repr Record）•数字化管理（Digital Management）7. 模具常见故障及解决方法（Common Mold Faults and Solutions）•翘曲（Warping）•缺陷（Defects）•泛油（Flash）•磨损（Wear）•烧坏（Burning）•掉件（Part Ejection）•插损（Insert Damage）以上仅是模具专业领域常用词汇的一个简单对照表。
经典的 模具专业英语词汇表(中英对照)收藏起来吧
模具英语词汇表GLOSSARYAabrasive grinding 强力磨削 L3abrasive[E'breisiv] a.磨料的, 研磨的 L2,3 absence ['AbsEns] n.. 不在，缺席L17 accesssory[Ak'sesEri] n.附件L10 accommodate[E'kCmEdeit] v. 适应 L5 accordingly[E'kC:diNli] adv.因此,从而,相应地 L7,13 accuracy['AkjurEsi] n精度,准确性L1,3actuate['Aktjueit] vt.开动(机器), 驱动 L8 adequate['Adikwit] a. 足够的L13adhesive[Ed'hi:siv] n. 粘合剂L22adjacent[E'dVeisnt] a. 邻近的L13adopt[E'dCpt] vt. 采用 L4advance [Ed'vA:ns] n.进步 L7advisable [Ed'vaizbl] adj. 可取的L20agitate['AdViteit] v. 摇动 L2a large extent 很大程度 L4,13algorithm ['Al^EriTEm] n. 算法 L6align [E'lain] v 定位，调准L17alignment[E'lainmEnt] n. 校直L11all-too-frequent 频繁L17allowance[E'lEuens] n. 容差, 余量 L5alternate['C:ltEnit]v.交替,轮流L1alternative[C:l'tE:nEtiv] n. 替换物 L3 alternatively[C:l'tE:nEtivli] ad. 做为选择, 也许 L5 aluminiun[7Alju'minjEm] n.铝 L2ample['Ampl] adj. 充足的L20analysis [E'nAlEsis] n. 分析 L6ancillary['AnsilEri] a.补助的, 副的 L4angular ['A^julE] adj. 有角的L20annealing[E'li:liN] n.退火 L2aperture ['ApEtFE] n.孔L17applied loads 作用力L1appropriate [E'prEuprieit] a. 适当的 L6,20arc[a:k] n.弧, 弓形L10arise[E'raiz] vi. 出现, 发生L21arrange[E'reidV] v. 安排L12article['a:tikl] n.制品, 产品L21ascertain[7AsE'tein] vt. 确定, 查明L1assemble[E'sembl] vt.组装 L4attitude ['Atitju:d] n 态度L17auxiliary [C:^'ziljEri]adj. 辅助的 L8avoid[E'vCid] v.避免 L7axis['Aksis] n.轴 L5axle['Aksl] n.轮轴, 车轴L1Bbackup['bAk7Qp] n. 备份 L9batch [bAtF] n 一批L17bearing['bZEriN] n.轴承,支座L21bed[bed] n. 床身 L5behavior[bi'heivjE] n. 性能L1bench-work 钳工工作 L4bend[bend] v.弯曲L1beneath[bi'ni:W] prep在···下 L4bin [bin] n. 仓，料架L19blank [blANk] n. 坯料L20blank [blANk] v. 冲裁,落料L17blanking tool 落料模L17blast [blQst] n.一阵（风）L18blemish['blemiF] n. 缺点, 污点L13bolster['bEulstE] n. 模座,垫板 L4,5boost[bu:st] n. 推进 L9boring['bC:riN] n.镗削, 镗孔L4,5bracket ['brAkit] n. 支架L19brass [brAs] n.黄铜 L2break down 破坏L1breakage ['breikidV] n.破坏L17bridge piece L16brine[brain] n. 盐水 L2brittle['britl] adv.易碎的L1buffer [bQfE] n.缓冲器 L8built-in 内装的 L9bulging [bQldViN] n. 凸肚L22burr [bE:] n. 毛刺L17bush [buF] n. 衬套L17bush[buF]n. 衬套 L5by far (修饰比较级, 最高级)···得多, 最 L3 by means of 借助于 L5Ccabinet ['kAbinit] n.橱柜 L7call upon 要求L17carbide['ka:baid] n.碳化物L10 carburzing['ka:bjuretiN] n. 渗碳 L2 carriage['kAridV] n.拖板, 大拖板 L5carry along 一起带走L18carry down over 从···上取下L21carry out 完成L17case hardening 表面硬化 L2case[keis] n. 壳, 套 L2cast steel 铸钢L17casting['ka:stiN] n. 铸造,铸件 L3category['kAtE^Euri] n. 种类 L6,15caution ['kC:FEn] n. 警告，警示L17cavity and core plates 凹模和凸模板L11 cavity['kAviti] n.型腔, 腔, 洞 L4,10centre-drilling 中心孔 L5ceramic[si'rAmik] n.陶瓷制品 L3chain doted line 点划线L11channel['tFAnl] n.通道, 信道 L8 characteristic[kArEktE'ristik] n.特性L1check[tFek] v.核算L21chip[tFip] n.切屑, 铁屑 L3chuck [tFQk] n.卡盘L5,8chute [Fu:t] n. 斜道L19circa ['sEkE:] adv. 大约 L7circlip['sE:klip] n.(开口)簧环L22circuit['sE:kit] n. 回路, 环路L13circular supoport block L5circulate['sE:kjuleid] v.(使)循环L13clamp [klAmp] vt 夹紧L17clamp[klAmp] n.压板L12clay[klei] n. 泥土L2,7clearance ['kliErEns] n. 间隙L17clip [klip] vt. 切断，夹住L19cold hobbing 冷挤压 L4cold slug well 冷料井L12collapse[kE'lAps] vi.崩塌, 瓦解L22 collapsible[kE'lApsEbl] adj.可分解的L22 combination [kCmbi'neiFEn] n. 组合L18 commence[kE'mens] v. 开始, 着手L16 commence[kE'mens]v. 开始L21 commercial [kE'mE:FEl] adj. 商业的 L7 competitive[kEm'petitiv] a. 竞争的 L9 complementary[7kCmpli'mentEri] a. 互补的 L5 complexity [kem'pleksiti] n.复杂性 L8 complicated['kCmplEkeitid] adj.复杂的 L2 complication [kCmpli'keiFEn] n. 复杂化 L5,20 compression [kEm'preFEn] n.压缩L1 comprise[kEm'prais] vt.包含L16 compromise['kCmprEmaiz] n. 妥协, 折衷L13 concern with 关于 L6concise[kEn'sais] a. 简明的, 简练的 L9 confront[kEn'frQnt] vt. 使面临L14connector[kE'nektE] n. 连接口, 接头 L14 consequent['kCnsikwEnt] a. 随之发生的, 必然的 L3 console ['kCnsoul] n.控制台 L8consume [kEn'sjum] vt. 消耗, 占用 L7 consummate [kEn'sQmeit] vt. 使完善 L6 container[kEn'teinE] n. 容器L11contingent[ken'tindVEnt] a.可能发生的 L9 contour['kEntuE] n.轮廓 L5,21conventional[kEn'venFEnl] a. 常规的 L4 converge[kEn'vE:dV] v.集中于一点L21 conversant[kCn'vE:sEnt] a. 熟悉的L15 conversion[kEn'vE:FEn] n 换算, 转换 L7 conveyer[ken'veiE] n. 运送装置L12coolant['ku:lEnt] n. 冷却液L13coordinate [kEu'C:dnit] vt. (使)协调 L8copy machine 仿形(加工)机床 L4core[kC:] n. 型芯, 核心L2,4corresponding [ka:ri'spCdiN] n.相应的 L7 counteract [kauntE'rAkt] vt. 反作用,抵抗L20 couple with 伴随L20CPU (central processing unit) 中央处理器 L9 crack[krAk ] v.（使）破裂，裂纹 L1,17critical['kritikl] adj.临界的 L2cross-hatching 剖面线L16cross-section drawn 剖面图L11cross-slide 横向滑板 L5CRT (cathoder-ray tube) 阴极射线管 L9crush[krQF]vt.压碎L1cryogenic[7kraiE'dVenik ]a.低温学的L1crystal['kristl] adj.结晶状的L1cubic['kju:bik] a. 立方的, 立方体的 L3cup [kQp] vt (使)成杯状, 引伸L18curable ['kjurEbl] adj. 可矫正的L20curvature['kE:vEtFE] n.弧线L21curve [kE:v] vt. 使弯曲L20cutter bit 刀头, 刀片 L3cyanide['saiEnaid] n.氰化物 L2Ddash [dAF] n. 破折号 L6daylight ['deilait] n. 板距L12decline[di'klain] v.下落,下降,减少, L3,9deform[di'fC:m] v. (使)变形L1,3demonstrate['demEstreit ] v证明L21depict[di'pikt ] vt 描述L18deposite [di'pCzit] vt. 放置L20depression[di'preFEn] n. 凹穴L12descend [di'sent] v. 下降L20desirable[di'zairEbl] a. 合适的 L2detail ['diteil] n.细节，详情L17deterioration[ditiEri:E'reiFEn] n. 退化, 恶化L12 determine[di'tE:min] v.决定L16diagrammmatic[7daiEgrE'mAtik].a.图解的，图表的L10 dictate['dikteit] v. 支配L12die[dai] n.模具, 冲模, 凹模L2dielectric[daii'lektrik] n. 电介质L10die-set 模架L19digital ['didVitl ] n.数字式数字, a.数字的L3,6 dimensional[dddi'menFEnl] a. 尺寸的, 空间的 L3 discharge[dis'tFa:dV] n.v. 放电, 卸下, 排出 L3 discharge[dis'tFa:dV] v.卸下 L8discrete [dis'cri:t] adj. 离散的,分立的 L7dislodge[dis'lCdV] v. 拉出, 取出L12dissolution[disE'lu:FEn] n.结束 L9distinct [dis'tiNkt] a.不同的，显著的 L6distort [dis'dC:t] vt. 扭曲L20distort[dis'tC:t] vt. (使)变形, 扭曲L1distributed system 分布式系统 L9dowel ['dauEl] n. 销子L19dramaticlly [drE'mAtikli] adv. 显著地 L7drastic ['drAstik] a.激烈的L17draughting[dra:ftiN] n. 绘图L16draughtsman['drAftsmEn] n. 起草人L16drawing['drC:iN] n. 制图L11drill press 钻床 L8drum [drQm] n.鼓轮 L8dual ['dju:El] adv. 双的，双重的L18ductility [dQk'tiliti ] n.延展性 L1,21dynamic [dai'nAmik ] adj 动力的 L6Eedge [edV] n .边缘L20e.g.(exempli gratia) [拉] 例如L12ejector [i'dVektE] n.排出器，L18ejector plate 顶出板L16ejector rob 顶杆 L5elasticity[ilA'stisiti] n.弹性L1electric dicharge machining 电火花加工L3electrical discharge machining电火花加工 L10electrochemical machining 电化学加工L3electrode[i'lektrEud] n. 电极L10electro-deposition 电铸 L4elementary [elE'mentEri] adj.基本的 L2eliminate[i'limineit] vt. 消除, 除去L10 elongate[i'lCN^et] vt. (使)伸长, 延长L1 emerge [i'mE:dV] vi. 形成, 显现L20 emphasise['emfEsaiz] vt. 强调 L4 endeavour[en'devE] n. 尽力 L17 engagement[in'^eidVment] n. 约束, 接合L22 enhance[in'hAns] vt. 提高, 增强 L9ensure [in'FuE] vt. 确保，保证L17 envisage[in'vizidV] vt.设想L15erase[i'reis] vt. 抹去, 擦掉L16evaluation[i'vAlju7eiFEn] n. 评价, 估价L1 eventually[i'vEntFuEli ] adv.终于L21 evolution[evE'lu:FEn] n.进展L16 excecution[eksi'kju:FEn] n. 执行, 完成 L9 execute ['ekskju:t] v. 执行 L8exerte [i^'zE:t] vt. 施加L20experience[iks'piriEns] n. 经验L16 explosive[iks'plEusiv]adj.爆炸(性)的L22 extend[eks'tend] v. 伸展 L2external[eks'tE:nl] a. 外部的 L5,11 extract[eks'trAkt] v. 拔出L14extreme[iks'tri:m] n. 极端L13extremely[iks'tri:mli] adv. 非常地L12 extremity[iks'tmiti] n. 极端L13extrusion[eks'tru:VEn] n. 挤压, 挤出 L3FF (Fahrenheit)['fArEnhait]n.华氏温度 L2fabricate ['fAbrikeit] vt.制作,制造 L7 facilitate [fE'siliteit] vt. 帮助 L6facility[fE'siliti] n. 设备 L4facing[feisiN] n. 端面车削 L5fall within 属于, 适合于L15fan[fAn] n.风扇 L7far from 毫不, 一点不, 远非 L9fatigue[fE'ti^] n.疲劳L1feasible ['fi:zEbl] a 可行的L18feature ['fi:tFE] n.特色, 特征 L7,17feed[fi:d] n.. 进给 L5feedback ['fi:dbAk] n. 反馈 L8female['fi:meil] a. 阴的, 凹形的L11ferrule['ferEl] n. 套管L14file system 文件系统 L9fitter['fitE] n.装配工, 钳工 L4fix[fiks] vt. 使固定, 安装, vi. 固定L11fixed half and moving half 定模和动模L11flat-panel technology 平面(显示)技术 L9 flexibility[fleksi'biliti] n. 适应性, 柔性 L9 flexible['fleksEbl] a. 柔韧的L13flow mark 流动斑点L13follow-on tool 连续模L18foregoing ['fC:'^EuiN]adj. 在前的,前面的L8foretell[fC:'tell] vt. 预测, 预示, 预言 L9forge[fC:dV] n. v. 锻造 L3forming[fC:miN] n. 成型 L3four screen quadrants 四屏幕象限 L9 fracture['frAktFE] n.破裂L21free from 免于L21Ggap[^Ap] n. 裂口, 间隙L10gearbox['^iEbCks] n.齿轮箱 L5general arrangement L16govern['^QvEn] v.统治, 支配, 管理L13grain [^rein] n. 纹理L20graphic ['^rAfik] adj. 图解的 L6grasp [^rAsp] vt. 抓住 L8grid[^rid] n. 格子, 网格L16grind[^raind] v. 磨, 磨削, 研磨 L3grinding ['^raindiN] n. 磨光,磨削 L3,20 grinding machine 磨床 L5gripper[^ripE] n. 抓爪, 夹具 L9groove[^ru:v] n. 凹槽L12guide bush 导套 L5guide pillar 导柱 L5guide pillars and bushes 导柱和导套L11Hhandset['hAndset] n. 电话听筒 L4hardness['ha:dnis] n.硬度L1,2hardware ['ha:dwZE] n. 硬件 L6headstock['hedstCk] n.床头箱, 主轴箱 L5 hexagonal[hek'sA^Enl] a. 六角形的, 六角的L11 hindrance['hindrEns] n.障碍, 障碍物 L11hob[hCb] n. 滚刀, 冲头 L4hollow-ware 空心件L21horizontal[hCri'zCntl] a. 水平的L16hose[hEuz] n. 软管, 水管L13hyperbolic [haipE'bClik] adj.双曲线的 L7Ii.e. (id est) [拉] 也就是L12identical[ai'dentikl] a同样的L16identify [ai'dentifai] v. 确定, 识别 L7idle ['aidl] adj.空闲的 L8immediately[i'mi:djEtli] adv. 正好, 恰好L12 impact['impAkt] n.冲击L1impart [im'pa:t] v.给予 L11,17implement ['implimEnt] vt 实现 L6impossibility[impCsE'biliti] n.不可能L21 impression[im'preFEn] n. 型腔L11in contact with 接触L1in terms of 依据L1inasmuch (as)[inEz'mQtF] conj.因为, 由于 L3inch-to-metric conversions 英公制转换 L7 inclinable [in'klainEbl] adj. 可倾斜的L20inclusion [in'kluFEn] n. 内含物L19 inconspicuous[inkEn'spikjuEs] a. 不显眼的L14 incorporate [in'kC:pEreit] v 合并,混合L17 indentation[7inden'teiFEn ] n.压痕L1indenter[in'dentE] n. 压头L1independently[indi'peinEntli] a. 独自地, 独立地L16 inevitably[in'evitEbli] ad. 不可避免地L14 inexpensive[inik'spensiv]adj. 便宜的 L2 inherently [in'hiErEntli] adv.固有的 L7injection mould 注塑模L11injection[in'dVekFEn] n. 注射L11in-line-of-draw 直接脱模L14insert[in'sE:t] n. 嵌件L16inserted die 嵌入式凹模L19inspection[in'spekFEn] n.检查,监督 L9 installation[instE'leiFEn] n. 安装L10integration [inti'^reiFEn] n.集成 L6intelligent[in'telidVEnt]a. 智能的 L9 intentinonally [in'tenFEnEli] adv 加强地，集中地L17 interface ['intEfeis] n.. 界面 L6internal[in'tE:nl] a. 内部的L1,5interpolation [intEpE'leiFEn] n.插值法 L7 investment casting 熔模铸造 L4irregular [i'regjulE] adj. 不规则的，无规律L17 irrespective of 不论, 不管L11irrespective[iri'spektiv] a. 不顾的, 不考虑的L11 issue ['isju] vt. 发布，发出 L6Jjoint line 结合线L14Kkerosene['kerEsi:n] n.煤油L10keyboard ['ki:bC:d ] n. 健盘 L6knock [nRk] v 敲，敲打L17Llance [la:ns] v. 切缝L19lathe[leiT] n. 车床 L4latitude ['lAtitju:d] n. 自由L17lay out 布置L13limitation[limi'teiFEn] n.限度,限制,局限(性) L3local intelligence局部智能 L9locate [lEu'keit] vt. 定位L18logic ['lCdVik] n. 逻辑 L7longitudinal['lCndVE'tju:dinl] a. 纵向的 L5longitudinally['lCndVE'tju:dinl] a. 纵向的L13look upon 视作, 看待L17lubrication[lju:bri'keiFEn ] n.润滑L21Mmachine shop 车间 L2machine table 工作台 L8machining[mE'Fi:niN] n. 加工 L3made-to-measure 定做L15maintenance['meintinEns] n.维护,维修 L7majority[mE'dVa:riti] n.多数L21make use of 利用 L2male[meil] a. 阳的, 凸形的L11malfunction['mAl'fQNFEn] n. 故障 L9mandrel['mAdtil] n.心轴L22manifestation[mAnifEs'teiFEn] n. 表现, 显示 L9 massiveness ['mAsivnis ] 厚实，大块 L19measure['meVE] n. 大小, 度量L1microcomputer 微型计算机 L9microns['maikrCn] n.微米L10microprocessor 微处理器 L9mild steel 低碳钢L17milling machine 铣床 L4mineral['minErEl] n.矿物, 矿产 L2minimise['minimaiz] v.把···减到最少, 最小化L13minute['minit] a.微小的L10mirror image 镜像L16mirror['mirE] n. 镜子L16MIT (Massachusetts Institute of Technology) 麻省理工学院 L7 moderate['mCdErit]adj. 适度的L1,2modification [mRdifi'keiFEn ] n. 修改, 修正 L6modulus['mCdjulEs] n.系数L1mold[mEuld] n. 模, 铸模, v. 制模, 造型 L3monitor ['mCnitE ] v. 监控 L6monograph['mCnE^ra:f] n. 专著 L4more often than not 常常 L20motivation[mEuti'veiFEn] n. 动机 L9mould split line 模具分型线L12moulding['mEudiN] n. 注塑件 L5,11move away from 抛弃L17multi-imprssion mould 多型腔模L12Nnarrow['nArEu] a. 狭窄的L12NC (numerical control ) 数控 L7nevertheless[7nevETE'les] conj.,adv.然而,不过L11 nonferrous['nCn'ferEs] adj.不含铁的, 非铁的 L2 normally['nC:mli]adv.通常地L22novice['nCvis] n. 新手, 初学者L16nozzle['nCzl] n. 喷嘴, 注口L12numerical [nju'merikl] n. 数字的 L6Oobjectionable [Eb'dVekFEbl] adj. 有异议的，讨厌的L17 observe[Eb'zE:v] vt. 观察 L2obviously ['CbviEsli] adv 明显地L17off-line 脱机的 L6on-line 联机 L9operational [CpE'reiFEnl] adj.操作的, 运作的 L8 opportunity[CpE'tju:niti] n. 时机, 机会L13 opposing[E'pEuziN] a.对立的, 对面的L12opposite['CpEzit] n. 反面 L1 a.对立的,对面的 L12 optimization [Rptimai'zeiFEn] n.最优化 L6orient ['C:riEnt] vt. 确定方向 L8orthodox ['C:WEdCks] adj. 正统的，正规的L19 overall['EuvErC:l] a.全面的,全部的 L8,13overbend v.过度弯曲L20overcome[EuvE'kQm] vt.克服, 战胜L10overlaping['EuvE'lApiN] n. 重叠 L4overriding[EuvE'raidiN] a. 主要的, 占优势的L11Ppack[pAk] v. 包装 L2package ['pAkidV] vt.包装 L7pallet ['pAlit] n.货盘 L8panel ['pAnl] n.面板 L7paraffin['pArEfin] n. 石蜡L10parallel[pArElel] a.平行的 L5penetration[peni'treiFEn ] n.穿透L1peripheral [pE'rifErEl] adj 外围的 L6periphery [pE'rifEri] n. 外围L18permit[pE'mit] v. 许可, 允许L16pessure casting 压力铸造 L4pillar['pilE] n. 柱子, 导柱 L5,17pin[pin] n. 销, 栓, 钉 L5,17pin-point gate 针点式浇口L12piston ['pistEn] n.活塞L1plan view 主视图L16plasma['plAzmE] n. 等离子 L9plastic['plAstik] n. 塑料 L3platen['plAtEn] n. 压板L12plotter[plCtE] n. 绘图机 L9plunge [plQndV] v翻孔L18plunge[plQndV] v.投入 L2plunger ['plQndVE ] n. 柱塞L19pocket-size 袖珍 L9portray[pC:'trei] v.描绘L21pot[pCt] n.壶L21pour[pC:] vt. 灌, 注L22practicable['prAktikEb] a. 行得通的L14 preferable['prefErEbl] a.更好的, 更可取的 L3 preliminary [pri'liminEri] adj 初步的，预备的L19 press setter 装模工L17press[pres] n.压,压床,冲床,压力机 L2,8 prevent [pri'vent] v. 妨碍L20primarily['praimErili] adv.主要地 L4 procedure[prE'si:dVE] n.步骤, 方法, 程序 L2,16 productivity.[prEudQk'tiviti] n. 生产力 L9profile ['prEufail] n.轮廓L10progressively[prE'^resiv] ad.渐进地L15 project[prE'dVekt] n.项目 L2project[prE'dVekt] v. 凸出L11projection[prE'dVekFEn] n.突出部分L21 proper['prCpE] a. 本身的L10property['prCpEti] n.特性L1prototype ['prEutEtaip] n. 原形 L7proximity[prCk'simiti] n.接近 L9prudent['pru:dEnt] a. 谨慎的L16punch [pQntF] v. 冲孔 L3punch shapper tool 刨模机L17punch-cum-blanking die 凹凸模L18punched tape 穿孔带 L3purchase ['pE:tFEs] vt. 买，购买 L6push back pin 回程杆 L5pyrometer[pai'nCmitE] n. 高温计 L2Qquality['kwaliti] n. 质量L1,3quandrant['kwCdrEnt] n. 象限 L9quantity ['kwCntiti] n. 量，数量L17quench[kwentF] vt. 淬火 L2Rradial['reidiEl] adv.放射状的L22ram [rAm] n 撞锤. L17rapid['rApid]adj. 迅速的 L2rapidly['rApidli]adv. 迅速地 L1raster['rAstE] n. 光栅 L9raw [rC:] adj. 未加工的 L6raw material 原材料 L3ream [ri:m] v 铰大L17reaming[ri:miN] n. 扩孔, 铰孔 L8recall[ri'kC:l] vt. 记起, 想起L13recede [ri'si:d] v. 收回, 后退L20recess [ri'ses] n. 凹槽,凹座,凹进处 L4,18 redundancy[ri'dQndEnsi] n. 过多 L9re-entrant 凹入的L12refer[ri'fE:] v. 指, 涉及, 谈及 L1,12reference['refErEns] n.参照,参考L21refresh display 刷新显示 L9register ring 定位环L11register['redVstE] v. 记录, 显示, 记数 L2regrind[ri:'^aind](reground[ri:'gru:nd]) vt. 再磨研L12 relative['relEtiv] a. 相当的, 比较的L12relay ['ri:lei] n. 继电器 L7release[ri'li:s] vt. 释放 L1relegate['relE7geit] vt. 把··降低到 L9reliability [rilaiE'biliti] n. 可靠性 L7relief valves 安全阀L22relief[ri'li:f] n.解除L22relieve[ri'li:v ]vt.减轻, 解除 L2remainder[ri'meindE] n. 剩余物, 其余部分 L4 removal[ri'mu:vl] n. 取出L14remove[ri'mu:v] v. 切除, 切削 L4reposition [ripE'ziFEn] n.重新安排L17represent[7repri'zentE] v 代表,象征L11reputable['repjutEbl] a. 有名的, 受尊敬的L15 reservoir['rezEvwa: ] n.容器, 储存器L22resident['rezidEnt] a. 驻存的 L9resist[ri'zist] vt.抵抗L1resistance[ri'zistEns] n.阻力, 抵抗 L1resolution[7rezE'lu:FEn] n. 分辨率 L9respective[ri'spektiv] a.分别的,各自的 L11respond[ris'pCnd] v.响应, 作出反应 L9 responsibility[rispCnsE'biliti] n.责任L13restrain[ris'trein]v.抑制L21restrict [ris'trikt] vt 限制，限定L18restriction[ris'trikFEn] n. 限制L12retain[ri'tein] vt.保持, 保留 L2,12retaining plate 顶出固定板L16reveal [ri'vil] vt.显示，展现L17reversal [ri'vEsl] n. 反向 L1,20right-angled 成直角的L20rigidity[ri'dViditi] n. 刚度 L1rod[rCd] n. 杆, 棒L1,5rotate['rEuteit] vt.(使)旋转 L5rough machining 粗加工 L5rough[rQf] a. 粗略的 L5,21routine [ru:'ti:n] n. 程序 L7rubber['rQbE] n.橡胶 L3,22runner and gate systems 流道和浇口系统L11Ssand casting 砂型铸造 L3satisfactorily[7sAtis'fAktrili] adv. 满意地L1saw[aC:] n. 锯子 L4scale[skeil]n. 硬壳 L2score[skC:] v. 刻划L14scrap[skrAp] n.废料, 边角料, 切屑 L2,3 screwcutting 切螺纹 L4seal[si:l] vt.密封L22secondary storage L9section cutting plane 剖切面L16secure[si'kjuE] v.固定L22secure[si'kjuE] vt.紧固,夹紧,固定 L5,22 segment['se^mEnt] v. 分割L10sensitive['sensitiv]a.敏感的L1,7sequence ['si:kwEns] n. 次序 L6sequential[si'kwenFEl] a.相继的L16seriously['siEriEsli] adv.严重地L1 servomechanism ['sE:vE'mekEnizm] n.伺服机构 L7 Servomechanism Laboratoies 伺服机构实验室 L7 servomotor ['sE:vEmEutE] n.伺服马达 L8setter ['setE] n 安装者L17set-up 机构L20sever ['sevE] v 切断L17severity [si'veriti] n. 严重L20shaded[FAdid] adj.阴影的L21shank [FANk] n. 柄. L17shear[FiE]n.剪,切L1shot[FCt] n. 注射L12shrink[FriNk] vi. 收缩L11side sectional view 侧视图L16signal ['si^nl] n.信号 L8similarity[simi'lAriti] n.类似L15simplicity[sim'plisiti] n. 简单L12single-point cutting tool 单刃刀具 L5situate['sitjueit] vt. 使位于, 使处于L11slide [slaid] vi. 滑动, 滑落L20slideway['slaidwei] n. 导轨 L5slot[slCt] n. 槽 L4slug[slQ^] n. 嵌条L12soak[sEuk] v. 浸, 泡, 均热 L2software ['sCftwZE] n. 软件 L6solid['sClid] n.立体, 固体 L9solidify[sE'lidifai] vt.vi. (使)凝固, (使)固化L13 solution[sE'lu:FEn] n.溶液L2sophisiticated [sE'fistikeitid] adj.尖端的,完善的 L8 sound[saund] a. 结实的, 坚固的) L1spark erosion 火花蚀刻L10spindle['spindl] n. 主轴L5,8spline[splain] n.花键 L4split[split] n. 侧向分型, 分型 L12,14spool[spu:l] n. 线轴L14springback n.反弹L20spring-loaded 装弹簧的L18sprue bush 主流道衬套L11sprue puller 浇道拉杆L12square[skwZE] v. 使成方形 L4stage [steidV] n. 阶段 L16,19 standardisation[7stAndEdai'zeiFEn] n. 标准化L15 startling['sta:tliN] a. 令人吃惊的L10steadily['stedEli ] adv. 稳定地L21step-by-step 逐步 L8stickiness['stikinis] n.粘性L22stiffness['stifnis] n. 刚度L1stock[stCk] n.毛坯, 坯料 L3storage tube display 储存管显示 L9storage['stC:ridV] n. 储存器 L9 straightforward[streit'fC:wEd]a.直接的 L10strain[strein] n.应变L1strength[streNW] n.强度L1stress[stres] n.压力,应力L1stress-strain应力--应变 L6stretch[stretF] v.伸展 L1,21strike [straik] vt. 冲击L20stringent['strindVEnt ] a.严厉的L22stripper[stripE] n. 推板L15stroke[strouk] n. 冲程, 行程L12structrural build-up 结构上形成的L11sub-base 垫板L19subject['sQbdVikt] vt.使受到L21submerge[sEb'mE:dV] v.淹没L22subsequent ['sQbsikwent] adj. 后来的L20subsequently ['sQbsikwentli] adv. 后来, 随后 L5substantial[sEb'stAnFEl] a. 实质的L10substitute ['sQbstitju:t] vt. 代替,.替换 L7subtract[sEb'trAkt] v.减, 减去L15suitable['su:tEbl] a. 合适的, 适当的 L5suitably['su:tEbli] ad.合适地L15sunk[sQNk](sink的过去分词) v. 下沉, 下陷 L11superior[sE'piEriE] adj.上好的L22susceptible[sE'septEbl] adj.易受影响的 L7sweep away 扫过L17symmetrical[si'metrikl] a. 对称的 L14synchronize ['siNkrEnaiz] v.同步,同时发生L8Ttactile['tAktail] a. 触觉的, 有触觉的 L9tailstock['teilstCk] n.尾架 L5tapered['teipEd] a. 锥形的L12tapping['tApiN] n. 攻丝 L8technique[tek'ni:k] n. 技术L16tempering['tempErN] n.回火 L2tendency['tendEnsi] n. 趋向, 倾向 L13tensile['tensail] a.拉力的, 可拉伸的 L2 拉紧的, 张紧的 L1 tension ['tenFEn] n.拉紧,张紧L1terminal ['tE:mEnl ] n. 终端机 L6terminology[tE:mi'nClEdVi ] n. 术语, 用辞L11theoretically [Wi:E'retikli ] adv.理论地L21thereby['TZEbai] ad. 因此, 从而L15thermoplastic['WE:mEu'plAstik] a. 热塑性的, n. 热塑性塑料 L3 thermoset['WE:mEset] n.热固性L12thoroughly['WQrEuli] adv.十分地, 彻底地 L2thread pitch 螺距 L5thread[Wred] n. 螺纹 L5thrown up 推上L17tilt [tilt] n. 倾斜, 翘起L20tolerance ['tClErEns] n..公差L17tong[tCN] n. 火钳 L2tonnage['tQnidV] n.吨位, 总吨数 L3tool point 刀锋 L3tool room 工具车间L10toolholder['tu:lhEuldE] n.刀夹,工具柄 L5toolmaker ['tu:l'meikE] n 模具制造者 L17toolpost grinder 工具磨床 L4toolpost['tu:l'pEust] n. 刀架 L4torsional ['tC:FEnl] a扭转的 . L1toughness['tCfnis] n. 韧性 L2trace [treis] vt.追踪 L7tracer-controlled milling machine 仿形铣床 L4 transverse[trAns'vE:s] a. 横向的 L5tray [trei] n. 盘，盘子，蝶L19treatment['tri:tmEnt] n.处理L2tremendous[tri'mendEs] a. 惊人的, 巨大的 L9 trend [trend] n.趋势 L7trigger stop 始用挡料销L17tungsten['tQNstEn] n.钨 L10turning['tE:niN] n.车削 L4,5twist[twist ] v.扭曲，扭转L1two-plate mould 双板式注射模L12Uultimately['Qltimitli] adv终于. L6undercut moulding 侧向分型模L14undercut['QndEkQt] n. 侧向分型L14undercut['QndEkQt] n.底切L12underfeed['QndE'fi:d] a, 底部进料的L15 undergo[QndE'^Eu] vt.经受L1underside['QndEsaid] n 下面,下侧L11undue[Qn'dju:] a.不适当的, 过度的 L4,10 uniform['ju:nifC:m] a.统一的, 一致的L12utilize ['ju:tilaiz] v 利用L17Utopian[ju'tEupiEn] adj.乌托邦的, 理想化的L21Vvalve[vAlv] n.阀L22vaporize['veipEraiz] vt.vi. 汽化, (使)蒸发L10 variation [vZEri'eiFEn] n. 变化L20various ['vZEriEs] a.不同的,各种的 L1,20vector feedrate computation 向量进刀速率计算 L7 vee [vi:] n. v字形L20velocity[vi'lCsiti] n.速度L1versatile['vEsEtail] a.多才多艺的,万用的 L5,8 vertical['vE:tikl] a. 垂直的L16via [vaiE] prep.经,通过 L8vicinity[vE'siniti] n.附近L13viewpoint['vju:pCint] n. 观点 L4Wwander['wCndE] v. 偏离方向L13warp[wC:p] v. 翘曲 L2washer ['wCFE] n. 垫圈L18wear [wZE] v.磨损 L7well line 结合线L13whereupon [hwZErE'pCn] adv. 于是L19winding ['waindiN] n. 绕, 卷 L8with respect to 相对于L1,5withstand[wiT'stAnd] vt.经受,经得起 L1work[wE:k] n. 工件 L4workstage 工序L19wrinkle['riNkl] n.皱纹vt.使皱L21Yyield[ji:ld] v. 生产 L9Zzoom[zu:] n. 图象电子放大 L9GLOSSARYAabrasive grinding 强力磨削 L3abrasive[E'breisiv] a.磨料的, 研磨的 L2,3 absence ['AbsEns] n.. 不在，缺席L17 accesssory[Ak'sesEri] n.附件L10 accommodate[E'kCmEdeit] v. 适应 L5 accordingly[E'kC:diNli] adv.因此,从而,相应地 L7,13 accuracy['AkjurEsi] n精度,准确性L1,3actuate['Aktjueit] vt.开动(机器), 驱动 L8 adequate['Adikwit] a. 足够的L13adhesive[Ed'hi:siv] n. 粘合剂L22adjacent[E'dVeisnt] a. 邻近的L13adopt[E'dCpt] vt. 采用 L4advance [Ed'vA:ns] n.进步 L7advisable [Ed'vaizbl] adj. 可取的L20agitate['AdViteit] v. 摇动 L2a large extent 很大程度 L4,13algorithm ['Al^EriTEm] n. 算法 L6align [E'lain] v 定位，调准L17alignment[E'lainmEnt] n. 校直L11all-too-frequent 频繁L17allowance[E'lEuens] n. 容差, 余量 L5alternate['C:ltEnit]v.交替,轮流L1alternative[C:l'tE:nEtiv] n. 替换物 L3 alternatively[C:l'tE:nEtivli] ad. 做为选择, 也许 L5 aluminiun[7Alju'minjEm] n.铝 L2ample['Ampl] adj. 充足的L20analysis [E'nAlEsis] n. 分析 L6ancillary['AnsilEri] a.补助的, 副的 L4angular ['A^julE] adj. 有角的L20annealing[E'li:liN] n.退火 L2aperture ['ApEtFE] n.孔L17applied loads 作用力L1appropriate [E'prEuprieit] a. 适当的 L6,20arc[a:k] n.弧, 弓形L10arise[E'raiz] vi. 出现, 发生L21arrange[E'reidV] v. 安排L12article['a:tikl] n.制品, 产品L21ascertain[7AsE'tein] vt. 确定, 查明L1 assemble[E'sembl] vt.组装 L4attitude ['Atitju:d] n 态度L17auxiliary [C:^'ziljEri]adj. 辅助的 L8avoid[E'vCid] v.避免 L7axis['Aksis] n.轴 L5axle['Aksl] n.轮轴, 车轴L1Bbackup['bAk7Qp] n. 备份 L9batch [bAtF] n 一批L17bearing['bZEriN] n.轴承,支座L21bed[bed] n. 床身 L5behavior[bi'heivjE] n. 性能L1bench-work 钳工工作 L4bend[bend] v.弯曲L1beneath[bi'ni:W] prep在···下 L4bin [bin] n. 仓，料架L19blank [blANk] n. 坯料L20blank [blANk] v. 冲裁,落料L17blanking tool 落料模L17blast [blQst] n.一阵（风）L18blemish['blemiF] n. 缺点, 污点L13bolster['bEulstE] n. 模座,垫板 L4,5boost[bu:st] n. 推进 L9boring['bC:riN] n.镗削, 镗孔L4,5bracket ['brAkit] n. 支架L19brass [brAs] n.黄铜 L2break down 破坏L1breakage ['breikidV] n.破坏L17bridge piece L16brine[brain] n. 盐水 L2brittle['britl] adv.易碎的L1buffer [bQfE] n.缓冲器 L8built-in 内装的 L9bulging [bQldViN] n. 凸肚L22burr [bE:] n. 毛刺L17bush [buF] n. 衬套L17bush[buF]n. 衬套 L5by far (修饰比较级, 最高级)···得多, 最 L3 by means of 借助于 L5Ccabinet ['kAbinit] n.橱柜 L7call upon 要求L17carbide['ka:baid] n.碳化物L10carburzing['ka:bjuretiN] n. 渗碳 L2carriage['kAridV] n.拖板, 大拖板 L5carry along 一起带走L18carry down over 从···上取下L21carry out 完成L17case hardening 表面硬化 L2case[keis] n. 壳, 套 L2cast steel 铸钢L17casting['ka:stiN] n. 铸造,铸件 L3category['kAtE^Euri] n. 种类 L6,15caution ['kC:FEn] n. 警告，警示L17cavity and core plates 凹模和凸模板L11 cavity['kAviti] n.型腔, 腔, 洞 L4,10centre-drilling 中心孔 L5ceramic[si'rAmik] n.陶瓷制品 L3chain doted line 点划线L11channel['tFAnl] n.通道, 信道 L8 characteristic[kArEktE'ristik] n.特性L1check[tFek] v.核算L21chip[tFip] n.切屑, 铁屑 L3chuck [tFQk] n.卡盘L5,8chute [Fu:t] n. 斜道L19circa ['sEkE:] adv. 大约 L7circlip['sE:klip] n.(开口)簧环L22circuit['sE:kit] n. 回路, 环路L13circular supoport block L5circulate['sE:kjuleid] v.(使)循环L13clamp [klAmp] vt 夹紧L17clamp[klAmp] n.压板L12clay[klei] n. 泥土L2,7clearance ['kliErEns] n. 间隙L17clip [klip] vt. 切断，夹住L19cold hobbing 冷挤压 L4cold slug well 冷料井L12collapse[kE'lAps] vi.崩塌, 瓦解L22 collapsible[kE'lApsEbl] adj.可分解的L22 combination [kCmbi'neiFEn] n. 组合L18 commence[kE'mens] v. 开始, 着手L16 commence[kE'mens]v. 开始L21 commercial [kE'mE:FEl] adj. 商业的 L7 competitive[kEm'petitiv] a. 竞争的 L9 complementary[7kCmpli'mentEri] a. 互补的 L5 complexity [kem'pleksiti] n.复杂性 L8 complicated['kCmplEkeitid] adj.复杂的 L2 complication [kCmpli'keiFEn] n. 复杂化 L5,20 compression [kEm'preFEn] n.压缩L1。
模具专业英语词汇
模具专业英语词汇landed plunger mold 有肩柱塞式模具burnishing die 挤光模英语站landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroform ed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroform ed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具injection mold 注塑模rubber molding 橡胶成形hot chamber die casting 热室压铸sand mold casting 砂模铸造extrusion mold 挤出模multi-cavity mold 多模穴模具palletizing die 叠层模plaster mold 石膏模three plates mold 三板模plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模runner system浇道系统sprue/cold material trap 浇道/冷料井sprue puller 拉杆runner design 流道设计main runner 主流道secondary runner 次流道gate design 浇口设计submarine gate 潜伏浇口tunnel gate 隧道式浇口pinpoint gate 点浇口fan gate 扇形浇口side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口dish gate 盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣insulated runner/hot runner 热浇道runner plat 浇道模块valve gate阀门浇口slag well 冷料井cold slag 冷料渣sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆)注塑缺陷：flash 飞边warpage 翘曲air trap 积风blush 发赤flow line 流痕splay 银纹short shot 短射sink mark 缩痕streak 条纹void 缩孔weld line 熔接线gas mark 烧焦cold slug 冷斑delamination 起皮burr 毛刺flaw/scratch 刮伤gloss 光泽glazing 光滑surface check 表面裂痕hesitation 迟滞注塑工艺:molding conditions 成型条件drying 烘干barrel temperature 料筒温度melt temperature 熔化温度mold temperature 模具温度injection pressure 注塑压力back pressure 背压injection speed 注塑速度screw speed 螺杆转速tensile strength 抗拉强度tensile elongation 延伸率flexural modulus 弯曲模数flexural strength 抗弯强度shrinkage 收缩率regrind usage 次料使用机械设备:lathe车床planer |刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机punching machine 冲床robot机械手common equipment常用设备EDM=Electron Discharge Machining 放电加工3D coordinate measurement 三次元量床boring machine 搪孔机milling machine 铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床模具零件:top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot 撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance 模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodAabrasion n. 磨损mósǔnabrasion resistance n. 耐磨损性nài mósǔn xìng abrasive n. 磨料móliàoaccelerator n. 促进剂cùjìnjìaccuracy n. 准确性zhǔnquèxìngacrylic n. 丙烯酸bǐngxīsuān，压克力yākelì additive n. 添加剂tiānjiājìadhere v. 黏附niánfùadhesion n. 黏合niánhéadhesive n. 胶粘剂jiāozhānjìair entrapment n. 困气kùnqìanneal v. 退火tùihuǒassemble v. 总成zǒngchéngBbarrel n. 机筒jītǒng，料筒liàotǒngblow molding n. 吹塑成型chūisù chéngxíng blow molding machine n. 吹塑机chūisùjībrittle adj. 脆性cùixìngbubble n. 气泡qìpàoby-product n. 副产品fùchǎnpǐnCcalendering n. 压延yāyáncarbon steel n. 碳素钢tànsù gāngcasting n. 铸造 zhùzàocatalyst n. 催化剂cūihuàjìcavity n. 型腔xíngq iāngchemical resistance n. 耐化学腐蚀性nài huàxué fǔshí xìngchip v. 削xiāo，凿záoclamping force n. 锁模力suǒmólìclamping tonnage n. 锁模吨位suǒmó dūnwèicomputer aided design (CAD) n. 电脑辅助设计diànnǎo fǔzhù shèjìcomputer aided manufacture (CAM) n. 电脑辅助制造diànnǎo fǔzhù zhìzào computer numerical control (CNC) n. 电脑数字控制diànnǎo shùzì kòngzhìceramic n. 陶瓷táocícold rolled steel n. 冷轧圆钢lěng zháyuán gāngcold runner n. 冷流道lěng liúdàocolorant n. 着色剂 zhuósèjìcomposite n. 复合材料fùhé cáiliàocompression strength n. 抗压强度kàngyā qiángdùcooling channel/circuit n. 冷却管道lěngquè guǎndàocooling rate n. 冷却速率lěngquè sùlǜcore n. 型芯xíngxīn，模芯móxīncorrosion n. 腐蚀fǔshícorrosion resistance n. 耐腐蚀性nài fǔshí xìngcure v. 固化gùhuàcustom adj. 定制dìngzhìcycle time n. 循环时间xúnhuán shíjiānDdegassing n. 排气páiqìdensity n. 密度mìdùdeform v. 变形biànxíngdie n. 冲模chòngmódie casting n. 压铸yāzhù，模铸mózhùdimension n. 尺寸chǐcùndimensional tolerance n. 尺寸公差chǐcùn gōngchàdistort v. 扭曲niǔqūdraft angle n. 拨模斜度bōmó xiédùdwell time n. 驻留时间zhùliú shíjiāndye n. 染料ránliàoEejector mark n. 顶出痕迹dǐngchū hénjìejection pin n. 顶出杆dǐngchū gān，推顶锁tūidǐng suǒ，脱模锁tuōmó suǒejection plate n. 推顶板tūidǐng bǎn，脱模板tuōmó bǎnejection rod n. 脱模板拉杆t uōmó bǎn lāgānelastomer n. 弹性体tánxìngtǐelectrical discharge machining (EDM) n. 电火花加工diànhuǒhuā jiāgōng epoxy n. 环氧树脂huányǎngshùzhīextruder n. 挤出机jǐchūjīextrusion n. 挤出jǐchū，挤塑jǐsùFfabricate v. 制造zhìzàofiber n. 纤维xiānwéifiberglass n. 玻璃纤维bōli xiānwéifiber reinforcement n. 纤维增强xiānwéi zēngqiángfilm n. 薄膜báomófire retardant n. 阻燃剂zǔránjìflash n. 溢料yìliàoflow mark n. 流痕liúhénflow rate n. 流动速率liúdòng sùlǜfluorescent adj. 荧光yíngguāngfluorescent brightener n. 荧光增白剂yíngguāng zēngbáijìfoam n. 泡沫pàomòfuse v. 熔合rónghéGgas assisted injection molding n. 气辅注射成型 qìfǔzhùshè chéngxíng gate n. 浇口jiāokǒugate mark n. 浇口痕jiāokǒu héngear n. 齿轮chǐlúngrinder n. 研磨机yánmójī，磨床móchuángHheat conduction n. 热传导rè chuándàoheater band n. 加热圈jiārè quānheat treatment n. 热处理rè chǔlǐhigh density polyethylene (HDPE) n. 高密度聚乙烯gāo mìdù jùyǐxī high impact plastic n. 高抗冲塑料gāo kàngchòng sùliàohigh impact polystyrene n. 高抗冲聚苯乙烯gāo kàngchòng jùběnyǐxī hobbing n. 滚铣gǔnxǐ，挤压制模jǐyā zhìmó，切压制模qiēyā zhìmó holding n. 保压bǎoyāhot runner n. 热流道rè liúdàoIimpact strength n. 冲击强度chòngjī qiángdùinjection n. 注射zhùshè，注塑 zhùsùinjection molding n. 注塑成型zhùsù chéngxínginjection molding machine n. 注塑机zhùsùjīinjection pressure n. 注塑压力zhùsù yālìinsulated runner n. 绝热流道juérè liúdào，保温流道 bǎowēn liúdào insulation layer n. 绝热层juérè cénginternally heated runner n. 内加热流道nèi jiārè liúdàointernal void n. 内部空腔nèibù kōngqiāngJjoint n. 接头jiētóu，连接liánjiēlaser n. 激光jīguānglaser cutter n. 激光切割机jīguāng qiēgējīlathe n. 车床chēchuánglocating pin n. 定位锁 dìngwèi suǒlow density polyethylene n. 低密度聚乙烯dī mìdù jùyǐxī Mmelt v. 熔融róngróngmelt index n. 熔融指数róngróng zhǐshùmill (metal) v. 铣xǐmachining n. 机加工jījiāgōngmachining path n. 加工路径jiāgōng lùjìng manufacture v. 制造zhìzàomeld line n. 融合线rónghé xiànmetal machining n. 金属加工jīnshù jiāgōngmilling machine n. 铣床xǐchuángmodel n. 模型móxíngmonomer n. 单体dāntǐmold n. 模具mójùmold cavity n. 模具型腔mójù xíngqiāngmold life n. 模具寿命mójù shòumìngmulticavity mold n. 多腔模具duōqiāng mójù multicolor injection molding n. 多色注塑duōsè zhùsù multigate mold n. 多浇口模具duōjiāokǒu mójùmultishot injection molding n. 多色注塑duōsè z hùsùNnozzle n. 喷嘴pēnzǔiNylon n. 尼龙NílóngOoxidation resistance n. 耐氧化性nài yǎnghuà xìng oxidize v. 氧化yǎnghuàPpackaging n. 包装bāozhuāngpacking n. 补料bǔliàoparison n. 型坯xíngpīpart n. 零件língjiànparting line n. 分模线fēnmóxiànparting plane n. 分模面fēnmómiànpinhole gate n. 针孔形浇口zhēnkǒngxíng jiāokǒu plastic n. 塑料sùliàoplasticity n. 塑性sùxìngplasticizer n. 增塑剂zēngsùjìplotter n. 绘图机hùitújīpolish v. 抛光pāoguāngpolycarbonate (PC) n. 聚碳酸酯jùtànsuānzhǐpolyethylene n. 聚乙烯jùyǐxīpolyester n. 聚酯jùzhǐpolymer n. 聚合物（体）jùhéwù(tǐ)，高聚物gāojùwù polymerization n. 聚合jùhépolystyrene n. 聚苯乙烯jùběnyǐxīpolyurethane n. 聚氨脂jù'ānzhīpolyvinyl chloride (PVC) n. 聚氯乙烯jùlǜyǐxīporous adj. 多孔duōkǒngprecise adj. 精密jīngmìprecision n. 精度jīngdùprecision injection machine n. 精密注塑机jīngmì zhùsùjī precision molding n. 精密模塑jīngmì mósùpreform n. 预成型yùchéngxíngpreform molding n. 预成型模塑yùchéngxíng mósùprocess v. 处理chǔlǐ；加工jiāgōngproduction line n. 生产线shēngchǎnxiànprototype n. 原型yuánxíngpunch n. 冲头chòngtóuQquench v. 淬火cùihuǒRregrind n. 回用料húiyòngliàoresin n. 树脂shùzhīrib n. 肋条lèitiáorib stiffener n. 加强肋jiāqiáng lèirigidity n. 刚性gāngxìngripple n. 波纹bōwén，皱纹zhòuwénrough adj. 粗糙cūcāorubber n. 橡胶xiàngjiāo；橡皮xiàngpírunner n. 流道liúdàorunnerless adj. 无流道 wúliúdàorunnerless injection mold n. 无流道注塑模具wúliúdào zhùsù mójùSscale n. 比例bǐlìschematic n. 图解tújiěseal v. 密封mìfēngshort shot n. 短射duǎnshè，欠料注射 qiànliào zhùshèshot n. 注料 zhùliào，注射 zhùshèshot size n. 注塑量zhùsùliàngshrinkage n. 收缩shōusuōside core n. 侧性芯cèxìngxīnside gate n. 侧向浇口cèxiàng jiāokǒusilicone n. 聚硅氧烷jùgūiyǎngwánsilicone rubber n. 硅橡胶gūixiàngjiāosimulate v. 模拟mónǐsingle cavity mold n. 单腔模具dān qiāng mójùsingle gate mold n. 单浇口模具dān jiāokǒu mójùsink mark n. 凹痕āohén，缩痕suōhénslide n. 滑动阀huádòngfásoftener n. 软化剂ruǎnhuàjìsprue n. 注道zhùdàosteam channel n. 汽道qìdàostabilizer n. 稳定剂wěndìngjìstamping n. 冲压chòngyāstainless steel n. 不锈钢bùxiùgāngstrain n. 应变yìngbiànstreak n. 条纹tiáowén，条痕tiáohénstress n. 应力yìnglìstripper n. 脱模器tuōmóqì，顶出器dǐngchūqìstripper ring n. 脱模圈tuōmóquānsurface defect n. 表面缺陷biǎomiàn quēxiànsurface treatment n. 表面处理biǎomiàn chǔlǐsymmetrical adj. 对称dùichēngsymmetry n. 对称dùichēngTtie bar n. 连接杆liánjiēgānTeflon n. 特氟隆Tèfúlóngtemper v. 回火hùihuǒtensile strength n. 抗张强度kàngzhāng qiángdù thermoforming n. 热成型rèchéngxíngthermoplastic n. 热塑性塑料rèsùxìng sùliào adj. 热塑性rèsùxìng thermoset n. 热固性塑料règùxìng sùliào adj. 热固性règùxìng three-dimensional adj. 三维空间sānwéi kōngjiāntolerance n. 公差gōngchàtool mark n. 刀痕dāohéntool steel n. 工具钢gōngjù gāngUultrasonic welder n. 超声波焊接机chāoshēngbō hánjiējīundercut n. 凹孔āokǒngunit cost n. 单价dānjiàVvacuum n. 真空zhēnkōngvented injection molding n. 排气式注塑成型páiqìshì zhùsù chéngxíng viscosity n. 黏度niándù，黏性 niánxìngvulcanize v. 硫化liúhuàWwarpage n. 翘曲变形qiàoqū biànxíngwear n. 磨损mósǔnwear resistance n. 耐磨损性nài mósǔn xìngweld line n. 熔接线róngjiē xiànworking drawing n. 工程图根据国家标准，以下为部分塑料模具成形术语的标准翻译。
模具专业英语词汇
模具专业英语词汇Aabrasion n. 磨损abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 Bback pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚bottom plate 下托板(底板) bushing bolck 衬套barrel temperature 料筒温度 blush 发blank through dies 漏件式落料模 burnishblow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺button dby-product n. 副产品 Ccalendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿clamping force n. 锁模力 clamping tonnage n. 锁模吨位 coil spring 弹簧computer aided design (CAD) n. 电脑辅助设计computer aided manufacture (CAM) n. 电脑辅助制造cover plate盖板computer numerical control (CNC) n. 电脑数字控制ceramic n. 陶瓷calendaring molding 压延成形cavity 型控母模center-gated mold 中心浇口式模具clod hobbing 冷挤压制模center-gated mold 中心浇口式模具clod hobbing 冷挤压制模chill mold 冷硬用铸模cold chamber die casting 冷式压铸cold forging 冷锻cold slag 冷料渣cold slug 冷斑cold rolled steel n. 冷轧圆钢cold runner n. 冷流道colorant n. 着色剂compacting molding 粉末压出成形composite n. 复合材料composite dies 复合模具compound molding 复合成形compression molding 压缩成形compression strength n. 抗压强度cooling channel/circuit n. 冷却管道cooling rate n. 冷却速率core n. 型芯 /模芯corrosion n. 腐蚀corrosion resistance n. 耐腐蚀性counter punch 反凸模cure v. 固化custom adj. 定制cycle time n. 循环时间Ddegassing n. 排气density n. 密度deform v. 变形delamination 起皮diaphragm gate 隔膜浇口die n. 冲模die casting n. 压铸 /模铸deburring punch压毛边冲子die holder下夹板die pad下垫板die set下模座dimension n. 尺寸dimensional tolerance n. 尺寸公差dowel pin固定销dish gate 盘形浇口dip mold 浸渍成形distort v. 扭曲double stack mold 双层模具draft angle n. 拨模斜度drying 烘干duplicated cavity plate 复板模dwell time n. 驻留时间dye n. 染料Eedge gate 侧缘浇口ejector mark n. 顶出痕迹ejection pin n. 顶出杆/推顶锁 /脱模锁ejection plate n. 推顶板/脱模板ejection rod n. 脱模板拉杆elastomer n. 弹性体electrical discharge machining (EDM) n. 电火花加工electroformed mold 电铸成形模encapsulation molding 注入成形epoxy n. 环氧树脂eq-height sleeves=spool等高套筒expander die 扩径模extruder n. 挤出机extrusion n. 挤出，挤塑extrusion die 挤出模extrusion molding 挤出成形Ffabricate v. 制造family mold 反套制品模具fan gate 扇形浇口fantail die 扇尾形模具fiber n. 纤维feature die公母模female die母模(凹模)fiberglass n. 玻璃纤维fiber reinforcement n. 纤维增强film n. 薄膜film gate 薄膜浇口fire retardant n. 阻燃剂fishtail die 鱼尾形模具flash 飞边/溢料flash gate 闸门浇口flash mold 溢料式模具flaw/scratch 刮伤flexural modulus 弯曲模数flexural strength 抗弯强度flow line 流痕flow mark n. 流痕flow rate n. 流动速率fluorescent adj. 荧光fluorescent brightener n. 荧光增白剂foam n. 泡沫fuse v. 熔合Ggang dies 复合模gas assisted injection molding n. 气辅注射成型gate n. 浇口gate design 浇口设计gate mark n. 浇口痕gear n. 齿轮grinder n. 研磨机 /磨床gas mark 烧焦glazing 光滑gloss 光泽foam forming 发泡成形forming die 成型模forging roll 轧锻gravity casting 重力铸造groove punch压线冲子guide pin导正销guide plate定位板guide pad导料块gypsum mold 石膏铸模H heat conduction n. 热传导heater band n. 加热圈heat treatment n. 热处理hesitation 迟滞high density polyethylene (HDPE) n. 高密度聚乙烯high impact plastic n. 高抗冲塑料high impact polystyrene n. 高抗冲聚苯乙烯hobbing n. 滚铣/挤压制模 /切压制模holding n. 保压hollow(blow) molding 中空(吹出)成形hot runner n. 热流道hot chamber die casting 热室压铸hot forging 热锻hot-runner mold 热流道模具Iimpact strength n. 冲击强度ingot mold 钢锭模injection n. 注射/注塑injection mold 注塑模injection molding 射出成形injection molding machine n. 注塑机injection pressure 注塑压力injection speed 注塑速度inner stripper内脱料板inner guiding post内导柱inner hexagon screw内六角螺钉insert入块(嵌入件)insulated runner n. 绝热流道/保温流道insulation layer n. 绝热层internally heated runner n. 内加热流道internal void n. 内部空腔investment casting 精密铸造Jjoint n. 接头/连接/Llancing die 切口模laminating method 被覆淋膜成形lancing die 切口模landed plunger mold 有肩柱塞式模具landed positive mold 有肩全压式模具laser n. 激光laser cutter n. 激光切割机lathe n. 车床lifter guide pin浮升导料销lifter pin顶料销located block定位块located pin定位销loading shoe mold 料套式模具loose detail mold 活零件模具long nozzle 延长喷嘴方式loose mold 活动式模具louvering die 百叶窗冲切模lost wax casting 脱蜡铸造low density polyethylene n. 低密度聚乙烯low pressure casting 低压铸造lower plate下模板lower sliding plate下滑块板lower stripper下脱料板Mmale die公模(凸模)main runner 主流道manifold die 分歧管模具melt v. 熔融melt index n. 熔融指数mill (metal) v. 铣machining n. 机加工machining path n. 加工路径manufacture v. 制造matched die method 对模成形法matched mould thermal forming 对模热成形模meld line n. 融合线metal machining n. 金属加工melt temperature 熔化温度milling machine n. 铣床model n. 模型modular mold 组合式模具monomer n. 单体mold n. 模具mold cavity n. 模具型腔mold life n. 模具寿命mold temperature 模具温度molding conditions 成型条件modular mold 组合式模具multi color injection molding n. 多色注塑multi-cavity mold 多模穴模具multi-gate mold 复式浇口模具multi shot injection molding n. 多次注料注塑Nnozzle n. 喷嘴Nylon n. 尼龙Ooffset bending die 双折冷弯模具outer bush外导套outer guiding post外导柱outer stripper外脱料板oxidation resistance n. 耐氧化性oxidize v. 氧化Ppackaging n. 包装packing n. 补料palletizing die 叠层模parison n. 型坯part n. 零件parting line n. 分模线parting plane n. 分模面pierce die 冲孔模pin销pinhole gate n. 针孔形浇口pinpoint gate 点浇口plain die 简易模plaster mold 石膏模plastic n. 塑料plasticity n. 塑性plasticizer n. 增塑剂plotter n. 绘图机polish v. 抛光porous adj. 多孔precise adj. 精密polycarbonate (PC) n. 聚碳酸酯polyethylene n. 聚乙烯polyester n. 聚酯polymer n. 聚合物（体） /高聚物polymerization n. 聚合polystyrene n. 聚苯乙烯polyurethane n. 聚氨脂polyvinyl chloride (PVC) n. 聚氯乙烯porous mold 通气性模具positive mold 全压式/挤压式模具pressure die 压紧模profile die 轮廓模progressive die 顺序模portable mold 手提式模具positive mold 全压式模具powder forming 粉末成形powder metal forging 粉末锻造precision n. 精度precision injection machine n. 精密注塑机precision forging 精密锻造precision molding n. 精密模塑preform n. 预成型preform molding n. 预成型模塑press forging 冲锻pressure die 压紧模profile die 轮廓模progressive die 连续模/顺序模prototype mold 雏形试验模具process v. 处理chǔlǐ；加工production line n. 生产线prototype mold 雏形试验模具prototype n. 原型punch冲头punch set上模座punching die 落料模punch holder上夹板punch pad上垫板Qquench v. 淬火Rraising(embossing) 压花起伏成形re-entrant mold 倒角式模具reel-stretch punch卷圆压平冲子regrind n. 回用料regrind usage 次料使用resin n. 树脂rib n. 肋条rib stiffener n. 加强肋ribbon punch压筋冲子rigidity n. 刚性ring gate 环形浇口ripple n. 波纹/皱纹riveting die 铆合模rocking die forging 摇动锻造roller滚轴rotary forging 回转锻造rotational molding 离心成形rough adj. 粗糙round punch圆冲子rubber n. 橡胶 /橡皮írubber molding 橡胶成形runner n. 流道runner design 流道设计runner plat 浇道模块runner system浇道系统runnerless adj. 无流道runnerless injection mold n. 无流道注塑模具Ssand mold casting 砂模铸造scale n. 比例schematic n. 图解screw speed 螺杆转速seal v. 密封secondary runner 次流道sectional die 拼合模/对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套shearing die 剪边模shell casting 壳模铸造short shot n. 短射shot n. 注料shot size n. 注塑量shrinkage 收缩(率)side core n. 侧性芯side gate 侧浇口silicon n. 聚硅氧烷silicon rubber n. 硅橡胶simulate v. 模拟single cavity mold 单腔模具single gate mold n. 单浇口模具sink mark n. 凹痕 /缩痕sinter forging 烧结锻造six sides forging 六面锻造slag well 冷料井slide n. 滑动阀sliding block滑块sliding dowel block滑块固定块special shape punch异形冲子spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板stop screw止付螺丝stripper pad脱料背板stripping plate内外打(脱料板)supporting block for location定位支承块slit gate 缝隙浇口slush molding 凝塑成形softener n. 软化剂solid forging die 整体/拼合锻模splay 银纹split forging die 拼合锻模split mold 分割式模具/双并式模具sprue 注道/ 浇口/溶渣sprue/cold material trap 浇道/冷料井sprue gate 射料浇口，直浇口sprueless mold 无注道残料模具sprue lock pin 料头钩销(拉料杆)sprue puller 拉杆sprueless mold 无射料管方式/无注道残料模具squeeze casting 高压铸造squeezing die 挤压模steam channel n. 汽道stabilizer n. 稳定剂stamped punch字模冲子stamping n. 冲压stainless steel n. 不锈钢stiffening rib punch = stinger 加强筋冲子strain n. 应变streak n. 条纹 /条痕stretch form die 拉伸成形模stress n. 应力stripper n. 脱模器/顶出器stripper ring n. 脱模圈submarine gate 潜伏浇口surface defect n. 表面缺陷surface treatment n. 表面处理surface check 表面裂痕swing die 振动模具symmetrical adj. 对称symmetry n. 对称swaging 挤锻sweeping mold 平刮铸模Ttab gate 搭接浇口Teflon n. 特氟隆temper v. 回火tensile strength n. 抗张强度tensile elongation 延伸率thermoforming n. 热成型thermoplastic n. 热塑性塑料 adj. 热塑性thermoset n. 热固性塑料 adj. 热固性three-dimensional adj. 三维空间three plates mold 三片式模具tie bar n. 连接杆tolerance n. 公差tool mark n. 刀痕tool steel n. 工具钢top plate上托板（顶板）top block上垫脚transfer molding 转送成形trimming die 切边模trimming punch切边冲子tunnel gate 隧道式浇口Uultrasonic welder n. 超声波焊接机undercut n. 凹孔unit cost n. 单价unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具up stripper上脱料板upper plate上模板upper holder block上压块upper mid plate上中间板Vvacuum n. 真空valve gate阀门浇口vented injection molding n. 排气式注塑成型viscosity n. 黏度/黏性void 缩孔vulcanize v. 硫化Wwarm forging 温锻warpage n. 翘曲变形wear n. 磨损wear resistance n. 耐磨损性weld line n. 熔接线wire spring圆线弹簧working drawing n. 工程图yoke type die 轭型模机械设备:3D coordinate measurement 三次元量床boring machine 搪孔机contouring machine 轮廓锯床copy grinding machine 仿形磨床cylindrical grinding machine 外圆磨床die spotting machine 合模机driller 钻床EDM=Electron Discharge Machining 放电加工electrical sparkle 电火花engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机grinder 磨床horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床lathe车床linear cutting 线切割miller 铣床milling machine 铣床planer |刨床punching machine 冲床robot机械手welder 电焊机分类（汉英）一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot 撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader 水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar 气阀：valves斜导边：angle pin五术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut o n B-plate.内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert 行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrod根据国家标准，以下为部分塑料模具成形术语的标准翻译。
模具专业术语（专业人士一定要收藏）
模具专业术语（专业人士一定要收藏）模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfermolding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plungermold 有肩柱塞式模具burnishing die 挤光模 landed positivemold 有肩全压式模具button die 镶入式圆形凹模loading shoemold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bendingdie 双折冷弯模具extrusion die 挤出模palletizing die叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing)压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavitymold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch formdie 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating centerpunch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导杆pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slidecore) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushingguide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板。
模具专用术语词汇
一﹑入水：gate进水位：水口形式：大水口：细水口：水口大小：转水口：唧嘴口径：二﹑流道：runner热流道：热嘴冷流道：唧嘴直流：圆形流道：流道电脑分析：流道平衡：热嘴：热流道板：发热管：探针：插头：插座：密封/封料：三﹑运水：water line喉塞：喉管：塑胶管：快速接头：四﹑模具零件：mold components 三板模：二板模：边钉/导边：边司/导套：中托司：中托边L：顶针板：托板：螺丝：管钉：内模管位：顶针：司筒：司筒针：推板：缩呵：扣机（尼龙拉勾)：斜顶：模胚(架)：上内膜：下内模：行位（滑块）：镶件：压座/斜鸡：耐磨板/油板：压条：撑头：唧嘴：挡板：定位圈：锁扣：扣鸡：推杆：栓打螺丝：顶板：活动臂：分流锥：水口司：垃圾钉：隔片：弹弓柱：弹弓：中托司：中托边：镶针：销子：波子弹弓：喉塞：锁模块：斜顶：斜顶杆：尼龙拉勾：活动臂：复位键﹑提前回杆：气阀：斜导边：承压平面平衡：模排气：回针碰料位：模总高超出啤机规格：顶针碰运水：料位出上/下模：模胚原身出料位：不准用镶件：用铍铜做镶件：初步（正式）模图设计：反呵：弹弓压缩量：稳定性好：强度不够：均匀冷却：扣模：热膨胀：公差：铜公模具术语gate locationgate typeedge gatepin-point gategate sizeswitching runner/gatesprue diameterhot runner,hot manifoldhot sprue/cold runnerdirect sprue gateround (full/half runner)mold flow analysisrunner balancehot spruehot manifoldcartridge heaterthermocouplesconnector plugconnector socketsealwater lineline plugtubeplastic tubejiffy quick connector plug/socker件：mold components3-plate mold2-plate moldleader pin/guide pinbushing/guide bushingshoulder guide bushingguide pinejector retainner platesupport platescrewdowel pinply bar scotcore/cavity inter-lockejector pinejector sleeveejector pinstripper platemovable core,return core core puller nylon latch lockliftermold basecavity insertcore insertslideinsertwedgewedge wear plateplatesupport pillarsprue bushingstop platelocating ringlatchparting lock setpush barS.H.S.Beracuretunlever armspure speraderbushstop pinbufflespring roddie springejector guide bushejector guide pinpindowel pinball catchpipe pluglock plateangle from pinangle ejector rodparting lockslever armearly return barvalvesangle pintermsparting surface support balanceparting line ventingreturn pin and cavity interferencemold base shut hightwater line interferes withejector pinpart from cavith(core)sidecavity direct cut on A-plate,core direct cut on B-plate. Do not use(core/cavity)insertuse beryllium copper insertpreliinary(final)mold designreverse corespring compressed lengthgood stability,stableinsufficient rigidityeven coolingstickingthero expansiontolerance。
模具词汇
一、模具词汇：1.模具：mold; mould; tool2.模胚：mold base3.塑胶，胶位：plastic4.模具图纸：mold drawing5.模胚/模架：mold base; mold frame6.模板：mold plate7.模具类型：mold type(两板模：2-plate mold, 三板模：3-plate mold)8.前模（母模）：cavity, fixing side(固定侧)；cavity也有型腔的意思，缩写为cav.9.后模：core; moving side(移动侧)10.镶件（入子）：insert;可换镶件：interchangeable insert前（后）模镶件：cavity(core) insert11.进胶点，浇口：injection point,; gate入水形式：gate type潜水：sub-gate;tunnel-gate直入水（大水口）：direct gate边入水：edge gate点入水：pin point gate扇形入水：fan gate香蕉形入水：banana gate腰果形入水：cashew gate月亮形入水：moon gate1.面板：top clamp plate2.底板：bottom clamp plate3.水口板：runner stripper plate4.推板：stripper plate5.托板：support plate6.方铁(也有公司叫模脚)：spacer block7.顶针面板：ejector retainer plate8.顶针底板：ejector plate9.导柱：leader pin10.导套：leader bush1.中托司：ejector guide pin2.中托司套：ejector guide bush3.排气：vent4.回针：return pin5.斜边，斜导柱：angular pin6.撑头：support pillar7.定位圈：locating ring8.销钉：dowel pin9.隔水片：baffle10.唧嘴：sprue bushing1.变形：deformdeformeddeformationwarpwarpedwarpagedistortdistorteddistortion2.缩水：shrink缩水率：shrinkage rate缩水纹：sink mark3.顶白：ejection mark4.流痕：flow mark5.粘模：sticking6.拖花：scratch7.批锋：flash8.烧焦痕：burn mark9.困气：gas trap10.走胶不满：short shot; not filled11.流道类型：runner type冷流道：cold runner热流道：hot runner一、句子表达：1.这个产品有点变形This part is a little deformed.2.产品骨位太厚，表面容易产生缩水This rib is too thick, easy to have(cause/appear) sink mark.3.成形后，产品表面有困气，建议增加镶件。
模具标件专业英语词汇
模具标件专业英语词汇一、模具（Mold）相关基础词汇。
1. Mold [məʊld] - 名词，模具；也可作动词，塑造，浇铸。
- 例句：This is a new type of injection mold.（这是一种新型的注塑模具。
）2. Die [daɪ] - 名词，冲模，钢模（在冲压工艺中使用）- 例句：The die is used for stamping metal sheets.（这个冲模用于冲压金属薄板。
）3. Cavity ['kævəti] - 名词，型腔；洞，凹处。
- 发音：['kævəti]- 例句：The cavity of the mold should be polished carefully.（模具的型腔应该仔细抛光。
）4. Core [kɔː(r)] - 名词，型芯；核心。
- 例句：The core is an important part of the mold.（型芯是模具的一个重要部分。
）二、模具标件（Standard Mold Components）词汇。
1. Guide Pin ['ɡaɪ d pɪn] - 名词，导柱。
- 例句：The guide pin helps to align the two parts of the mold.（导柱有助于使模具的两个部分对齐。
）2. Guide Bushing ['ɡaɪ d 'bʊʃɪŋ] - 名词，导套。
- 例句：The guide bushing is used in combination with the guide pin.（导套与导柱配合使用。
）3. Ejector Pin [i'dʒektə pɪn] - 名词，顶针。
- 例句：The ejector pin is used to push the finished product out of the mold.（顶针用于将成品从模具中顶出。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
模具（MOULD/MOLD，TOOL）：CAVITY：前模CORE：后模（定模）DIMENSION：寸法GATE：浇口/水口/入水口PIN GATE：点水口/点浇入水SIDE GATE：边水口/侧浇入水/大水口APPERANCE SURFACE：体裁面WARPAGE DIRECTION：变形方向DRAFT ANGEL：脱模斜度PARTING LINE/P。
L：分模线EJECT PIN/E。
P：注塑顶针BLAST/TEXTURE：喷啥，蚀纹MIRROR FINISH：镜面（抛光）处理POLISH：抛光EMD：放电加工WELD：熔接加工（烧焊）LATHE：车床MILLING CUTTER：铣刀MILLING MACHINE：铣床WIRE CUT：线切割CNC：主加工中心POWER DRILL：电钻DRILLING：钻孔FRITING：烧结ANNEALING：退火注塑术语（INJECTION）SCREW：螺杆WELD LINE：熔接线SINK MARK：缩痕DRAG MARK：脱花BURR：批锋FLOW MARK：流纹SHADOW MARK/GLOSS DIFFERENCE：光影SHORT：缺胶INJECTION CYCLE：成型周期compression molding压缩成型flash mold溢流式模具positive mold挤压式模具split mold分割式模具cavity型腔母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具（移转成型用模具） encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒 clamp force 锁模力non-return valve 止回阀shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure / packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比 mold close time 合模时间Resin 胶料Plasticization 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃 degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固 specific gravity 比重Elongation 延伸率 density 密度melting point 熔点Polystyrene 聚苯乙烯（PS） Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin 结晶形塑料模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate 撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance 模排气：parting line venting回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut height 顶针碰运水：water line interferes with ejector螺丝： screw 管钉：dowel pin 开模槽：ply bar slot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear platepin 料位出上/下模：part from cavity (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thero expansion 公差：tolorance 铜公(电极）：copper electrode模具結構名詞進澆名詞頂出名詞缺陷名詞射出名詞SMED即Single Minute Exchange of Dies（单分换模）它也被称作快速生产准备，该原则能被用于任何环境SMED是一种持续改进生产准备的方法—以达到尽可能低的时间(最终达到一触即可或无需生产准备) 生产准备对你们公司意味着:到生产线平稳运行之时，处于全速且无需更多调整。