加拿大ULC阻燃、防火测试标准

加拿大ULC阻燃、防火测试标准

CAN/ULC-S101-M89：建筑结构和材料的耐火性测试方法

CAN/ULC-S101-M89：Standard Methods of Fire Endurance Tests of Building Construction

and Materials

Abstract 摘要

This Standard covers fire endurance tests applicable to walls, partitions, floors, roofs, ceilings, columns, beams, and girders, as well as to some components of these building sub-assemblies. It is the intent that the fire endurance period established by this test method indicates performance only during the fire exposure period and shall not be construed as having determined suitability for use after fire exposure.

CAN/ULC-S102-M88：建筑材料和配件表面燃烧特性测试方法

CAN/ULC-S102-M88：Standard Method of T est for Surface Burning Characteristics of

Building Materials and Assemblies

Abstract 摘要

This method of test for surface burning characteristics of building materials is applicable to any type of building material that, by its own structural qualities or the manner in which it is applied, is capable of supporting itself in position or may be supported in the test furnace as described in this Standard or in a manner comparable to its recommended use. Where a material cannot be readily determined to be thermoplastic or thermoset, one test is conducted in accordance with this Standard and one additional test in conformance with requirements of CAN/ULC-S102.2, Standard Method of Test for Surface Burning Characteristics of Flooring, Floor Coverings, and Miscellaneous Materials and Assemblies.

The primary purpose of this test is to determine the comparative burning characteristics of the material or assembly under test by evaluating the flame spread over its surface when exposed to a test fire and thus establish a basis on which surface burning characteristics of different materials or assemblies may be compared, without specific considerations of all the end use parameters that might affect these characteristics.

It is the intent of this method to register performance during the period of exposure, and not to determine suitability for use after the test exposure.

CAN/ULC-S102.2-M88：地板,地面覆盖物和复合材料及配件表面燃烧特性测试方法

CAN/ULC-S102.2-M88：Standard Method of Test for Surface Burning Characteristics of

Flooring, Floor Covering, and Miscellaneous Materials and

Assemblies

Abstract 摘要

The primary purpose of the Standard is to determine the comparative burning

characteristics of the material or assembly under test by evaluating the flame spread over its surface when exposed to a test fire and thus establish a basis on which surface burning characteristics of different materials or assemblies may be compared, without specific considerations of all the end-use parameters that might affect these characteristics.

ULC-S102.3-M1982：光散射器和镜头的防火测试方法

ULC-S102.3-M1982：Standard Method of Fire Test of Light Diffusers and Lenses

Abstract 摘要

This test method is applicable to materials employed in light diffusers and lenses.

The testing procedure described herein is intended to assess the propensity of material employed in light diffusers and lenses to fall from its installed position before igniting when subjected to test fire exposure conditions in CAN/ULC-S102.

以上资料由防火资源网（）防火测试中心整理或发布。

ULC-S102.4-M1987：电线电缆的燃烧及烟雾特征防火测试方法

ULC-S102.4-M1987：Standard Method of Test for Fire and Smoke Characteristics of

Electrical Wiring and Cables

Abstract 摘要

This test is designed to provide information for evaluating the possibility of fire spreading in a plenum or other space used for environmental air along electrical wires or cables, optical-fiber cables or non-metallic raceways; or the possibility of high smoke levels being developed in the space when wiring or raceways are subject to fire exposure. The test method has been related to the results of tests on cables exposed to fires in simulated plenums.

This test method is used to determine if a cable or non-metallic raceway qualifies for an FT-6

classification as specified in CSA C22.2 No. 0.3, Test Methods for Electrical Wires and Cables or CSA C22.2 No. 262, Optical Fiber Cable and Communication Cable Raceway Systems.

This test method is for use in determining values of flame propagation distance and smoke optical density for electrical and optical-fiber cables and non-metallic raceways that are to be installed in ducts, plenums, and other spaces used for environmental air. It is not intended for use with cables enclosed in metallic raceways in those spaces. This method also determines values of flame propagation distance and smoke optical density for electrical and optical-fiber cables with combustible jackets or sheathes, and non-metallic raceways to determine their acceptability for use in buildings of non-combustible construction.