锂离子电池专业英语

锂离子电池常用专业英语

（一）

序号首字母英文中文

1 A aging 老化

2 B battery charger 充电器

3 black-fleck 黑斑

4 C cap 盖板

5 capacity density 能量密度

6 capacity grading 分容

7 cathode tab welding 极耳超焊

8 cell 电芯

9 charge(capacity) retention 荷电（容量）保持

10 checking code 检码

11 concave spot 凹点

12 constant current charge 恒流充电

13 constant current discharge 恒流放电

14 constant voltage charge 恒压充电

15 corrective measures 纠正措施

16 crack 裂纹

17 cut-off voltage 终止电压

18 cycle life 循环寿命

19 D dark trace 暗痕

20 degrade 降级

21 dent 凹痕

22 discharge depth 放电深度

23 distortion 变形

24 drape 打折

25 E Electrical and MechanicalServices Department 机电部

26 electrolyte 电解，电解液

27 empaistic 压纹

28 end-off voltage 放电截止电压

29 environmentally friendly 对环境友好

30 equipment first inspection 设备首检

31 erode 腐蚀

32 explosion-proof line 防爆线

33 F first inspection 首检

34 formation 化成

35 fracture 断裂

36 I inspection 检验

37 insulate 绝缘

38 internal resistance 内阻

39 J jellyroll 卷芯

40 joint 接缝，结合点

42 laser reticle 激光刻线

43 laser welding-flatwise weld 激光焊接-平焊

laser welding-standing weld 激光焊接-立焊

44 leakage 漏液

45 leak-checking 测漏

46 leaving out of welding 漏焊

47 limited charge voltage 充电限制电压

48 local action 自放电

49 M margin turnly 翘边

50 measuring the dimension of cells 电芯卡尺寸

51 meet requirement 达到要求

52 memory effects 记忆效应

53 N nick 划痕

54 nominal voltage 标称电压

55 notice-board confirmation 看板确认

56 nugget 硬块

57 O obverse 正面

58 open circuit voltage 开路电压

59 over charge 过充

60 over discharge 过放

61 over the thickness 超厚

62 P particle 颗粒

63 PE membrane PE膜

64 pit 坑点

65 placing cells into the box 电芯装盒

66 point inspection 点检

67 preventive measures 预防措施

68 pricking the tapes 扎孔

69 process inspection 制程检验

70 put the battery piled up 将电芯叠放在一起

71 Q qualified products 合格品

72 quality assurance 质量保证

73 quality control 质量控制

74 quality improvement 质量改进

75 quality match 品质配对

76 quality planning 质量策划

77 R rated capacity 额定容量

78 recharge 再充电

79 refitting the can of cell 电芯壳口整形

80 requirment 要求

81 reverse 背面，反面

82 rework 返工

83 ringing cells into pyrocondensation films 套热缩膜

85 sand aperture 砂眼

86 scar 疤痕

87 secondary battery 二次电池

88 select appearance 选外观

sharp-set 批锋

89 short circuit checking 测短路

90 smudginess 污物

91 spot welding by laser 激光点焊

92 spot welding place 点焊位置

93 spraying the code 喷码

94 spur 毛刺

95 sticking the PVC cover boards 贴面垫

96 storing 陈化

97 storing with high voltage 高压储存

98 T tabs deflection 极耳歪斜

99 tabs excursion 极耳错位

100 technics requiment 工艺要求

101 U ultrasonic welding 超声波焊接102 ultrasonic welding strength 超焊强度103 unqualified products 不合格品

104 W wave 波浪

105 working procedure 工序

（二）

盖板cover board

底板solepiece

钢珠steel ball

压钢珠press steel ball

防爆阀valve preventing explosion

大电流(倍率)放电discharge in high rate current

标称电压Normal voltage

标称容量normal capacity

放电容量discharge capacity

充电上限电压limited voltage in charge

放电下限电压terminating voltage in discharge

恒流充电constant current charge

恒压充电constant voltage charge

恒流放电constant current discharge

放电曲线discharge curve

充电曲线charge curve