吉普自由光天鉴电动尾门安装说明书
智能电动尾门专业知识讲座
? 智能电吸：尾门关闭碰到第二级锁之后，电吸功能开启，会缓慢把尾门拉紧锁 死
本文档所提供的信息仅供参考之用，不能作为科学依据，请勿模仿。文档如有不当之处，请联系本人或网站 删除。
本文档所提供的信息仅供参考之用，不能作为科学依据，请勿模仿。文档如有不当之处，请联系本人或网站 删除。
电尾门——支撑杆的结构
电动尾门基本结构是两根芯轴驱动杆构成。驱动杆通过主轴驱动器由一个内管和 一个外管组成其中内管中的电机和齿轮驱动着一个螺纹主轴该螺纹主轴在固定于外 管内侧的螺纹螺母上运动。电动支柱使用位于支柱内部电机内的电动主轴来开合行 李箱盖弹簧也对盖开启操作起到辅助作用
本文档所提供的信息仅供参考之用，不能作为科学依据，请勿模仿。文档如有不当之处，请联系本人或网站 删除。
壹捷电尾门的开关方式
? 打开方式：车内开关打开，原车钥匙打开，手动打开，共3种
? 关闭方式：车内开关关闭，原车钥匙关闭，手动关闭，后备箱按键关闭，共4 种
? 防夹功能：电动尾门开启或关闭过程中碰到障碍物，门会向反方向运动或停止 运行，有效防止夹伤，安全看得见
本文档所提供的信息仅供参考之用，不能作为科学依据，请勿模仿。文档如有不当之处，请联系本人或网站 删除。
本文档所提供的信息仅供参考之用，不能作为科学依据，请勿模仿。文档如有不当之处，请联系本人或网站 删除。
电尾门的主要配件
本文档所提供的信息仅供参考之用，不能作为科学依据，请勿模仿。文档如有不当之处，请联系本人或网站 删除。
本文档所提供的信息仅供参考之用，不能作为科学依据，请勿模仿。文档如有不当之处，请联系本人或网站
汽车车库门电动开关器安装与使用说明书
S M A N U As of date of manufacture, meets all ANSI/UL 325 Safety Requirements for Vehicular Garage Door OpenersM A N U A L C A R E F U L L Y B E F O R E I N S T A L A T I O N O R INSTALLER: Place this manual in the plastic envelope provided andpermanently attach to the wall near the pushbutton.Product Features....................................................2 Tools Required/Component Identification.....2 & 3 Assembly Instructions...........................................3 Identify Your Door Type.........................................4 Important Installation Instructions........................5 Installing the Opener..............................................6 Mounting the Front Bracket............................6 Mounting the Power Head...............................7 Using the Manual Release Mechanism...........7 Installation......................................8 Requirements/Permanent Wiring........9 Control and Auxiliary Equipment........................10 Standard Wall Push Button Installation.......10 Installation of the Super Station...................10 Remote Control Radio System .....................11 TABLE OF CONTENTSOR DEATH. Gives instructions to avoid FCC and IC Radio Operation Statement ......12 Installation of Safe Finish Photosystem.......13 Installation Checklist.....................................14 Operation and Adjustment Instructions............15 Important Safety Instructions.......................15 Basic Operating Parameters.........................15 Testing the Limit Settings.............................16 Testing the Sensitivity...................................16 Testing the Reversing System......................16 Testing the Safe Finish Photosystem...........17 Operating the Super Station Wall Station Wiring Diagram.....................................................18 Auxiliary Equipment Wiring Diagram..................19 Troubleshooting Guide........................................19 Warranty Statement. (20)CAUTION READ THESE STATEMENTS CAREFULLY AND FOLLOW THE INSTRUCTIONS CLOSELY The Warning and Caution boxes throughout this manual are there to protect you and your equipment.Pay close attention to these boxes as you follow the manual.WARNING CAUTION Indicates an ELECTRICAL hazard of DAMAGE to the door, door opener, or equipment. Gives instructions to avoid thehazard .Indicates an ELECTRICAL hazard of INJURY OR DEATH. Gives instructions to avoid the hazard . Indicates a MECHANICAL hazard of DAMAGE to the door, door opener, or equipment. Gives instructions to avoid the hazard . Residential Vehicular Garage Door OperatorMODELS: MVP and MVP-SQSTEPLADDER TAPE MEASUREWOOD BLOCKHAMMERHACKSAW TOOLS REQUIRED FOR INSTALLATION1/2” OPEN ENDWRENCHLEVELSCREW DRIVERSMALL SCREW DRIVER (1/8” HEAD)NOTE:Rail/Chain Assembly is packaged separately from the Power Unit. The Inner Trolley half, Front Idler Sprocket, Chain, and Limit Cams are assembled on the Tee Rail at the factory.Follow the steps outlined below to complete assembly prior to installation. Refer to the component identification illustrations on the previous page.STEP 1: Protect the Power Unit cover fromscratching during assembly by placing it on cardboard. Remove the two 5/16"-18 washered nuts and save them for later use. STEP 2: Position the Tee Rail/Chain Assembly box near the Power Unit. Open the box and locate theInstallation Hardware Packet.STEP 3: Locate the Outer Trolley half (packaged 104363ASSEMBLY INSTRUCTIONSDOOR MOUNTINGFRONT IDLERTROLLEY OUTER CHAIN GUARDWALL MOUNTING BRACKETRELEASE ROPE AND KNOBOPENER HARDWAREBAGTEE RAILRUBBER BUMPEROPENER HEAD UNITPHOTOSYSTEM HARDWARERADIO TRANSMITTERCONTROL WIRESPOOLIMPORTANT!IDENTIFY YOUR DOOR TYPE FROM THOSE ILLUSTRATED BELOW ANDFOLLOW INSTRUCTIONS FOR THAT TYPE OF DOORFOR THESE TYPES OF DOORS USE MODEL MVP OR MODEL MVP-SB. USE 7 FT, 8 FT OR 10 FT RAIL (MATCH DOOR HEIGHT)THE MODEL MVP SERIES IN NOT DESIGNED TO OPERATE THESETYPES OF DOORSone 5/16"-18 washered nut (supplied) Tighten the bolt a MAXIMUM of 1.5 turns after the bolt and nut are Recheck the nuts used to secure the TeeRail to the Power Unit, making sure they are tight. the Chain tension, Chain twist, Chain Guard and the position of both the Close Limit Switch and Open Limit Switch Actuators.CHAIN GUARDACTUATORSPROCKETSPROCKET 104366Assembly is now complete and you are ready to begin installation of the opener.CHAINMASTER LINKOUTER NUTINNER NUTMASTER LINKCHAINDOOR TYPE IDENTIFICATIONONE PIECE DOOR NO TRACKJAMB HARDWAREONE PIECE DOOR NO TRACKPIVOT HARDWAREHIGH ARC OF DOOR TRAVELHIGH ARC OF DOOR TRAVELDOORPIVOT104368TRACKTRACKDOORDOOR104367SECTIONAL DOOR CURVED TRACKONE PIECE DOOR HORIZONTAL TRACK JAMB HARDWAREHIGH ARC OF DOOR TRAVELHIGH ARC OF DOOR TRAVELPower Unit on a ladder or other sturdy support.Open the door to the full open position. Allowsection of the door (as shown in the illustration104372Step 8: Connecting the Door Arm to the Door Type 1: Door Mounted BracketVisually align the door arm connecting hole with the middle hole of the door bracket by rotating the tube section in the appropriate direction.Release the trolley (leave door arm attached) with the manual release cord and pull trolley toward the power head unit. Now rotate the door arm tube section two turns counterclockwise (increasing the exposed length of the door rod) to provide a cushion when the door is closed or encounters an obstruction. Align connecting hole in the door arm to middle hole in the door bracket; insert 3/8” diameter bolt and tighten locking nut, allowing for free pivot of the arm. Note: Do not overtighten locking nut as this will cause binding between the door arm and door bracket.Type 2: Strut Mounted BracketVisually align the door arm connecting hole with the connecting pin of the strut by rotating the tube section in the appropriate direction.Release the trolley (leave door arm attached) with the manual release cord and pull trolley toward the power head unit. Now rotate the door arm tube section two turns counter-clockwise (increasing the exposed length of the door rod) to provide a cushion when the door is closed or encounters an obstruction. Align connecting hole in the door arm with the strut mounted connecting bracket. Insert connecting pin through the hole in the door arm. Secure the connecting pin to the strut bracket according to the manufacturer’s instructions. Note: Door Bracket Mount or Strut Mount - If rod bottoms in cushion tube, cut rod to allow for proper function of this assembly. Set the outer trolley to re-engage, see page 7.Alternate StrutConnecting BracketCut to Fit110054-2Openers are subject to vibration during normal operation which may shorten their life spans.Rough Service bulbs, available at most hardware stores, are recommended. Fit Light Diffuser tabs into the panel slots as shown.On most models, theLimit Cams are installed at the factory. If the Limit Cams have not been installed, or it is necessary to move a Limit Cam to a different link, fasten them to the chain as shown at right in the approximate positions as illustrated below. Position theSwitch Actuators as shown below.104380106428FASTENING LIMIT CAM TOCHAINunder “Special Notes” at the While the LED is. The .LED will blink twice to confirm a valid code and Special Notes - Express CodingRepeat the steps listed above as needed or desired for each button. Each button can be programmed to a unique code, however all three buttons may be programmed at one time (Express Coding). To Express Code, select the “+” button in Step 2, then end the code entry in Step 3 with the “+” button (the first 8 entries can be any random code). The code for each button may be changed at any time.However, if the plus button is programmed as described above, it will replace the existing code settings of the zeroStep 1Step 2Step 3used, slide it into the recess provided on the back of the transmitter caseuntil the snaps on the caseHomeLink® is a registered trade mark of Johnson Controls, Inc. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept anyPRE-POWER ON-INSTALLATION CHECKLISTBefore continuing with the operation andadjustment section, make sure that:1. The front and rear mounts for the opener aresound and secure and the rail is positionedcorrectly above the high arc of the door, and thatthe opener is positioned over the door actioncenterline.2. For sectional door and one piece door withtracks, the position of the door arm (with thedoor closed), is such that it’s connecting point onthe trolley is 5” to 8” behind it’s connectingpoint on the door bracket. The door arm shouldnever be perfectly vertical when the door in inthe closed position.3. The Manual Release Label and cord are secureto the Manual Release Lever. The handle islocated 6 FT above floor level and requires nomore than a 50 pound pull to activate. Thetrolley and the release mechanism are properlylubricated.4. The standard wall push button or the SuperStation (deluxe wall push button station) is insuch a position and of such a height that it canonly be actuated by an adult of average height.The Control Button Warning label isprominently displayed next to the push button orwall station.5. All wiring is correct to codes or better. There isground continuity form the supply. The groundprong on the power cord is intact.6. All ropes have been removed from the door.The door moves freely without binding whenraised or lowered manually. The door iscorrectly balanced and lubricated. All doorhardware is secure and sound. The sensitivityhas been adjusted to minimum force for theapplication.7. The door reverses on obstructions to within 1.5"of the floor. The concrete or other surfacebeneath the closed door provided uniformcontact.8. The plastic envelope for this manual is attachedto the wall near the push button or wall stationand this manual is placed there for owner useand reference.9. On door with extension type counterbalancesprings, restraint cables have been placedthrough the springs.10. There is Ground Fault Interruption (GFI)protection of the power line to the opener or inthe receptacle.11. On doors with adjustable bottom edges, edgeshave been locked after adjustment.TURNING ON POWER TO THE OPENERNOTE: It is now necessary to turn on the power in order to run the opener to test the operation and check the limit settings. Before doing so, ensure that all mounting hardware is installed and has been properly tightened, that all electrical connections are per local code requirements, and that proper wiring practices have been followed. Also, double-check that all ropes have been removed from the door and that the doorway is clear.BASIC OPERATING PARAMETERS Please note the following Operating Parameters which apply to Openers with Auxiliary Entrapment Protection System (Safe Finish™ Photosystem, Installation Instructions on Page 15) and a standard wall push button connected. Please see page 17 for instructions concerning the Super Station Deluxe Wall Push Button operating parameters.IF THE DOOR IS…...FULLY OPEN, then pushing the standard wall Push Button or the radio control will cause the door to begin MOVING DOWNWARD. ...FULLY CLOSED, then pushing the wall Push Button or the radio control will cause the door to begin MOVING UPWARD....MOVING UPWARD, then pushing the wall Push Button will cause the door to STOP. The next push of the wall button will cause the door to begin MOVING DOWNWARD (Alternate Action Operation)....MOVING UPWARD, then pushing the radio control will cause the door to STOP. The next push of the wall button will cause the door to RESUME UPWARD MOVEMENT (Radio Operation). ...MOVING DOWNWARD, then pushing the wall Push Button or the radio control will cause the door to STOP, PAUSE FOR APPROXIMATELY ONE SECOND, AND THEN BEGIN MOVING UPWARD....MOVING DOWNWARD then reaches the down limit, the lamp will blink off for a 1/2 second then turn back on again, remaining on for 4 minutes 30 seconds and will then automatically turn off....MOVING UPWARD then reaches the open limit, the lamp will remain on for 4 minutes 30 seconds and will then automatically turn off.STEP 3: Testing the Sensitivity Force — To test theSensitivity System, start the Opener and grasp the bottom door handle halfway through the door's travel(opening or closing). When testing in the CLOSEdirection, a second person will be needed to maintainpressure on the Push Button IF an Auxiliary EntrapmentProtection Device has not yet been fitted. If a secondperson isunavailable, use astiff cardboard carton placed in the door's downward path to indicate the force the Opener isOPEN FORCEADJUSTMENTCLOSE FORCE ADJUSTMENT104391THE SENSITIVITY SYSTEM REVERSING TESTENSURE THAT THIS IMPORTANT SYSTEMW A R N I N G1 2 3 4 5 6 7 8 9 Plus Button Zero Button Minus ButtonIF DESIRED, RECORD YOUR RADIO TRANSMITTER CODE POSITIONSETTINGS HERESee Page 11 for Radio System programming instructions and FCC/RSS-210 Industry Canada statement. The opener radio system is HomeLink® compatible.Serial #: Date Installed: Your Dealer:This garage door operatorcomplies with all requirements ofANSI/UL Standard 325.P/N 190-111069 Rev. FX1 August 2007Copyright © 2007 Linear LLC。
电动尾门使用说明书PPT课件
关门动作的流程首先驱动电动撑杆执行关门动作，执行过程中不断采集到位信号及 防夹信号，出现防夹信号时立即停止电动撑 杆动作，并驱动电动撑杆回复到开启位
产品介绍
高品质
采用国际一线品牌供应链，让 产品水平达到国际顶尖水平。
多类型 针对各类型汽车的电动尾门推杆
智能化
全平台采用智能学习控制型，更舒 适更安全
第1页/共20页
深圳市壹胜佰科技有限公司
产品介绍
产品细节展示
紧密的结构设计，使得产品更具稳定性
第2页/共20页
深圳市壹胜佰科技有限公司
细节介绍
电动尾门细节介绍
第9页/共20页
深圳市壹胜佰科技有限公司
控制系统
电动尾门智能操作系统
搭载独家开发的智能电动尾门控制系统，只需将尾门 推杆安 装后接通电源，即可进入实时环境学习模式，自动记录 当前 环境尾门弹簧数值，尾门关门时间。正常开启关闭一次后 初 步学习模式完成。 用户立即就可以体验到无以伦比的体验。
自动修复系统
脚踢感应系统
第13页/共20页
深圳市壹胜佰科技有限公司
脚踢感应系统
（一） 通过独立的分析两条天线信号的动态变化值，才探测一 个有效的脚踢动作，从而 实现后尾门的打开与关闭功能。
（二） 两条天线装配在不同位置是为了区分有效动作和误操作 情况,经过控制系统的智 能甄别进行信号区别是否为有效 动作。
踢腿-﹥有效动作 车尾捡东西-﹥误动作 车底部杂物-﹥误动作 下雨天-﹥误动作
2018-Current Jeep JL Stealth Fighter 后排假板安装说明 说明书
Preparation:• Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake.• We recommend reading through the installation instructions in whole before performing the work.• Estimated Installation Time: 2 Hours for OEM Removal/Bumper Installation 1 Additional Hour to Wire Cube Lights **This installation requires 2 people for best results** **Labor Rates are based on a vehicle with no pre-existing damage. Wiring labor is based on a standard wiring procedure with light switches installed in an easily accessible location. Custom light triggering or switch mounting location will result in a greater labor charge.**You will need the following tools: - Ratchet - 8mm Socket - 16mm Socket - 17mm Socket - 18mm Socket - 21mm Socket - 3/16" Allen Wrench/Socket - 1/2" Wrench - Wire Crimpers - 7/32" Allen Wrench/Socket - 9/16" Socket & Wrench - Butt Connectors (x2) - Electrical Tape - Zip Ties - 3/4" Wrench - Drill - 9/16" Drill Bit - Putty Knife/Scraper- Epoxy Included in Kit:4 - Hex Head Bolts (M14-1.5 x 40mm) 4 - Flat Washers (M14) 3 - Button Head Bolts (5/16"-18 x 1") 3 - Flat Washers (5/16) 3 - Nylon Lock Nuts (5/16"-18) 1 - License Plate Bracket 2 - Hex Head Bolts (3/8"-16 x 1") 2 - Flat Washers (3/8") 2 - Knurled Rivet Nuts (3/8"-16) 1 - Grade 8 Bolt (3/8"-16 x 1") 2 - Grade 8 Washers (3/8") 1 - Hex Nut (1/2"-13) 1 - LED License Plate Light Kit Removal:1. Unplug the rear bumper harness connector, then release the two plastic clips holding the bumper end of theharness to the vehicle. This connector is located under the vehicle on the driver side. Refer to (Fig A).Release these clipsFig A2. Remove your OEM spare tire.3. Using a 16mm Socket, remove the bottom two bumper bolts and the two trailer plug bracket bolts. Save these bolts for reuse. (Fig B)Fig B4. Using a 16mm Socket, remove the bumper side support bolts (2 per side) that are accessible from underneath the truck on the outer section of the bumper. (Fig C)Fig C5. Using a 17mm Socket, remove the bumper mounting nuts (2 per side) which are accessible from underneath the vehicle. Then, remove the OEM bumper. (Fig D)Fig D6. Using an 8mm Socket, remove the three (per side) inner fender liner bolts referenced in (Fig E). Then, re-move the lower inner fender liner pieces from the vehicle.Fig E7. Remove the two bolts that hold on each bumper side support bracket. Then, remove both brackets from the vehicle. (Fig F)Fig F8. Use an 18mm Socket to remove the driver side tow hook bolts (x4). Then, use a 21mm Socket to remove the passenger side bumper mounting bracket bolts (x2). Remove the tow hook and both bumper mounting brackets from the vehicle. (Fig G)Fig G9. IF YOU HAVE A METAL BUMPER, FOLLOW THIS STEP. IF NOT, SKIP TO STEP 10. Remove the parking sensors from the OEM rear bumper. Do this by first spreading the tabs on the inner mounting ring and releasing the sensor out the back side of the bumper. Then, spread the tabs on the outer mounting ring to release it from the inner mounting ring. Finally, press the tabs in on the inner mounting ring to push it out the front side of the bumper. (Fig H)Spread these tabs andrelease the parkingsensor from the rearSpread these tabsand release the outermounting ring fromthe rearFig H10. IF YOU HAVE A PLASTIC BUMPER, FOLLOW THIS STEP. IF NOT, SKIP TO STEP 11. Remove the parking sensors from the OEM Rear Bumper. Do this by first spreading the tabs on the mounting ring and releasing the sensor out the back side of the bumper. Then, take a putty knife, scraper, or something similar and work it between the sensor ring mounting plate and the rear bumper. Use the scraper to cut through the plas-tic welds holding that plate to the OEM bumper. Once the plastic welds have been broken, the plate will be free from the bumper. M ake sure to keep track of the order/orientation of the sensors on the OEM bumper as you will need to install them in the same order/orientation on your new bumper. (Fig I)Use a scraperto separatethe mountingplate fromthe bumperThis is whatit looks likeonce itsseparated Fig I11. Release the series of plastic clips holding the OEM Bumper Harness in the OEM Bumper. Then, remove the harness from the OEM Bumper. (Fig J)Fig JInstallation:12. If you have any lights to install on your new bumper, now is a good time to do so. Please follow the light manufacturer's installation guide for mounting/wiring information.13. Install the supplied license plate bracket. Do this by lining the mounting holes on the bracket up with the mounting holes on the bumper. Then, use the supplied 5/16" Bolts (x3), 5/16" Washers (x3), and 5/16" Lock Nuts (x3) to secure the bracket to the bumper. Install all bolts loosely, then go back and torque them to 13 foot pounds. (Fig K)Fig K14. IF YOUR PARKING SENSORS LOOK LIKE THE SENSORS IN STEP 9, FOLLOW THIS STEP . IF NOT, SKIP TO STEP 16. Install the two outer OEM Parking Sensors on your new bumper by pressing the inner mounting ring in from the front until it clicks into place. Then, press the outer ring onto the inner ring from the backside. Finally, press the sensor into place from the back side. For the two outer sensors, install the sensors 180 degrees from the OEM orientation (with the raised portion of the mounting ring towards the center of the bumper). (Fig L)Fig L Install this backing ring with the slimmer part faced towards the center of thebumper. Install this ring with the fatter part faced towards the center of the bumper.15. For the two middle sensors, you will have to face the sensor mounting rings so that the fatter part is towards the top of the bumper as shown in (Fig M). Y ou will also have to switch the backing rings, so that the backing ring that originally went on the left side will now go on the right side and the backing ring that went on the right side will now go on the left side. (Fig N)Install the outer ring with the fatter part towards the top of the bumper Fig NInstall the backing rings with the slimmer part facing upwards.Install the left backing ring on theright side of the bumper and the right backing ring on the left side of the bumper. Fig M16. IF YOUR PARKING SENSORS LOOK LIKE THE SENSORS IN STEP 10, FOLLOW THIS STEP. IF NOT, SKIP TO STEP 18. Before installing the parking sensor mounting plates, you will have to trim both outer plates. Do this by setting them in place in their precut holes (push them in place from the back side keeping the same orientation as on the OEM bumper). Then, mark out where you will have to make your cuts. We cut them so that none of the mounting plate is visible from the front side of the bumper. Refer to (Fig O & Fig P)Before AfterFig PBefore AfterFig OApply epoxy on these faces17. IF YOUR PARKING SENSORS LOOK LIKE THE SENSORS IN STEP 10, FOLLOW THIS STEP . IF NOT, SKIP TO STEP 18. Use a strong epoxy to glue the parking mounting plates to your new bumper. Do this by applying epoxy on the front face of the mounting plate. Then, push the sensor mounting ring through the pre-cut hole in the bumper from the backside of the bumper, so that the front face of the mounting plate gets glued to the back side of the bumper. Install the sensor rings in the exact position they came off the OEM bumper. Once the glue has set, push the sensor into the back side of the mounting ring until it clicks into place. (Fig Q)Fig Q19. Mount your license plate to the license plate bracket using the supplied LED License Plate Lights as yourmounting bolts. Make sure the LED Lights are facing down at your license plate. (Fig S)Fig S18. Take the OEM bumper harness and plug it into the newly installed parking sensors. Make sure to leave the main plug of the harness on the driver side of the bumper. (Fig R)Fig R21. Cut the license plate light connector off the OEM Harness. Twist both Red Wires from the LED Lights together and butt connect them to the White/Blue Wire from the OEM Harness. Then, twist both Black Wires from the LED Lights together and butt connect them to the black wire from the OEM Harness. (Fig U)Fig U22. Re-cover the now exposed wiring with either electrical tape or wire loom and zip tie the OEM Bumper Har-ness how you would like it.20. Locate the license plate light connector on the OEM Bumper Harness. Remove the conduit far enough back to allow this connector to reach the ends of the LED License Plate Light wires. (Fig T)Fig T23. IF YOUR OEM BUMPER DID NOT HAVE THE BUMPER MOUNTING BOLTS REFERENCED IN STEP 3, FOLLOW STEPS 23 & 24. OTHERWISE, SKIP TO STEP 25. Find the holes on the bottom of the rear frame section. These holes are referenced in (Fig V) and are hexagon shaped. Take a 9/16" Drill Bit and drill them so they are circular.Fig V24. Find the supplied 3/8" Grade 8 Bolt (x1), 3/8" Grade 8 Washers (x2), and 1/2" Nut (x1). Assemble them as shown in (Fig W) to create a rivet nut installation tool. Once this tool has been assembled, place the supplied 3/8" Rivet Nuts in the newly drilled holes. Loosely thread the rivet nut installation tool into the rivet nuts. Then, while holding the 1/2" Nut steady, thread the rivet nut tool into the rivet nut until it gets tight. Once it is tight, back the tool out and the rivet nut will be set.Fig W25. Set your new bumper in place on the vehicle. Secure it to the vehicle using the supplied M14 Bolts (x4) and M14 Washers (x4). Do not reuse the stock bolts and leave these bolts loose for now. (Fig X)Fig X26. Use a 16mm Socket to install the lower bumper bolts that were set aside in Step 3. If your OEM bumper did not have those bolts, then install the supplied 3/8" Bolts (x2) and 3/8" Washers (x2) through these holes into your newly installed Rivet Nuts. (Fig Y)Fig Y27. Position the bumper so that it is straight in relation to the tailgate and is level when viewed from the side. Then, go back and tighten all mounting bolts to OEM torque specs.28. Plug in the connector from Step 1 and reinstall the plastic clips that hold it in place. 29. Set the trailer plug bracket in place, then reinstall the two trailer plug bracket bolts from Step 3. (Fig Z)Fig ZFor Additional Support or Technical Questions,Please Call 480-671-0820 or This product is protected by one or more U.S. patents/patents30. Stand back and enjoy your new Stealth Fighter™ Rear Bumper. 31. Check and re-tighten, if needed, all mounting bolts after 100 miles and periodically thereafter.。
吉普自由光天电动尾门安装说明书
百度文库1天鉴电动尾门安装说明书(自由光)电动举升门安装一、注意事项●本说明书中的所有图片仅供参考，图片与实物有可能不同，但安装方法是一样的。
●为方便您安装，请在安装前认真阅读该商品使用说明书；安装时需注意保护好您爱车的表面，避免刮花。
●请定期检查与车连接的所有配件是否松动，以确保使用安全。
1 12三、安装步骤二、配件清单参考配件清单和配件图检查配件是否齐全。
首先把尾厢盖板及遮物帘拿开拿出备胎，并拆开后盖板（箭头所示）拆开左边侧饰板3拆下尾门内饰板拆下左边穿线胶套两边4用一字螺丝刀把与举升杆与车门连接的头部的卡簧撬开，拆出原车举升杆，拆装过程中需把门顶住拆下原车气弹簧的车身支架的两个螺丝5安装产品所配的万向头，另一个螺丝孔位用拆下的螺丝拧上把产品举升杆装上，注意，带线的一头靠门那一边67把举升杆的线 从如图所示的胶塞里穿到门内把电源正极线，解锁信号线，解码线与拉锁控制线通过穿线胶套穿到车身上在穿线套两头打上表板蜡，利于穿线8解锁信号线，电源正极线与解码线从尾厢车顶穿到前面电源正极线与解码线从后排迎宾踏板穿到驾驶位910把电源正极线与保险丝座相连，保险丝座插入驾驶位方向盘下的保险丝盒上，如图所示，注意保险丝座的方向 如图所示，解锁信号线（黄色线）接B 柱上如图的接头右边从上数起第六根黄色线、如图所示，解码线与OBD线相连，再把OBD线插入原车OBD 接口1112把拔下的公接头接到线束的母接头，再把线束的公接头插到原车的母接头上把原车锁机上的插头拔下把负极线接到如图所示尾门上的螺丝上，注意要接在螺丝头与垫片中间开门开关线接尾门上的开关按钮处，如图所示，把接头拔下，把拔下的公接头接到线束的母接头，再把线束的公接头插到原车的母接头上13把所配的开关装到如图所示位置把控制盒放于尾门上，用所配的魔术贴固定好。
把所有内饰板还原。
最后检查所有内饰是否全部锁紧；1415四、免责声明：由于安装及使用不当而引发的相关问题及损失，不在我公司的质保范围内。
电动尾门开闭系统(轿车)
3.3 如图，将尾门按键线/转接线从支撑杆 管内引至尾门上，电源线从饰板内引 至中控驾驶位（搭铁线接线位置如图）
原车预留的尾 门按键槽位
5.1 拆下原车预留的尾门按键小盖板， 将尾门按键装入原车饰板预留的槽 位中，连接尾门按键线与尾门按键， 安装完成后测试尾门的各项功能， 确认无误后，复原各饰板
6. 饰板复原
安装前准备
根据我司的线束接线说明，接好各线束(注意地线位置)。 接线顺序：先连接各零部件线束，连接OK后再通电。 请勿在开机状态下，插拔已连接好的线束/附件，避免损坏主机。
装车后注意事项：
电动尾门安装结束后，需手工关闭激活系统后方可正常使用。 高度设置：在开门或关门过程中，当门运行到合适的高度位置，按一次 加装的尾门按键，使尾门暂停运行后，通过长按加装的尾门关闭按键3秒， 当出现嘀嘀的响声后，尾门系统记忆功能激活，关闭尾门后再次开启， 即可达到设定高度。
安装步骤
安装步骤
安装步骤
1. 拆原车尾门饰板
1.1 大众-迈腾外观（拆装前，先关闭原车尾 1.2 拆掉尾门饰板上的门锁胶套，如图 门，观察尾门两侧高低缝隙，确认原车状态OK） 用工具拆下箭头指示位置的两颗螺 丝后，拆下尾门大饰板
1.3 如图掰开锁扣饰板，用工具分别拆 除侧饰板箭头指示位置的固定螺钉
2. 拆车身左侧饰板/专用球头支架安装
加强板 球头螺钉
原车弹簧
用螺丝固定 用螺丝固定
原车球头
2.1 如箭头所示，拆掉锁扣饰板处固定 胶塞
2.2 拆掉左侧支撑杆处的塑胶固定板后 掰开侧饰板，取下原车弹簧
2.3 将加强板安装在图中指示位置并用 两颗螺钉进行固定，专用球头螺钉装上 垫片安装在加强板上(内侧的原车球头不拆)
3. 电动撑杆安装/专用拉锁组合安装/主线束布线/搭铁线接线
2007-2014年Jeep JK HD风isation尾板门套装说明书
Parts Included Qty 93-288AR300K Cup Holder Bracket 4 93-288AR300L Tailgate Table Swing Out 193-288AR300N Tailgate Mount 1 93-288AR300U Tailgate Table Swing Out 193-288AR300A Tailgate Table Top 1 97-288AR300Q Stainless Badge 197-288AR300X Bottle Opener 1 0048603 Sash Lock: Oil Rubbed Bronze 1Hardware Pack: Rubber Bumper 1 9540K921 Round rubber Bumper 2 8638T43 Push-In Rubber Bumper 2 Hardware Pack: Swing Out Hinge 1 6mm-1.0 X 80mm Black Button Head Bolt 4 6mm Black Nylock Nut 4 6mm Black SAE Flat Washer 81/4” Nylon Flange Sleeve Washer 8Hardware Pack: (Inside) 1 3/8"-16 Threaded Insert 4 3/8”-16 X 1” Black Button Head Bolt 43/8” Black Hardened Flat Washer 12NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included Qty Hardware Pack: SS Badge and Bumps 1#10-24 X 5/8” Black Button Head Bolt 6 #10-24 Black Nylock Nut 6#10-24 SAE Black Flat Washer 12Hardware Pack: Drink Ledges 1#10-24 X 1/4” Black Button Head Bolt 4 Hardware Pack: Bump Stops 1 #10-24 X 3.4” Black Button Head Bolt 2 #10-24 Black Nylock Nut 2#10-24 SAE Black Flat Washer 4Hardware Pack: Hinge 1 1/4”-20 X 1” Black Button Head 2 1/4”-20 Black Stover Nut 21/4” Black Flat Washer 4Hardware Pack: Tailgate Mount (Outside) 1 8mm-1.25 X 35mm Black Head Bolt 8 8mm Black Flat Washer 8Step 1: Place the vehicle on a flat, level surface and engage the parking brake.Step 2: Install the stainless steel badge (97-288AR300Q) to the table top (93-288AR300A)mounting holes using the (2) supplied 10-24 X 5/8” button head bolt and hardware. (Fig. A)Step 3: Install the sash lock (0048603) to the table top (93-288AR300A) mounting holes using the (2) supplied 10-24 X 5/8” button head bolt and hardware.Step 4: Install the bottle opener (97-288AR300X) to the table top (93-288AR300A) mount-ing holes using the (2) supplied 10-24 X 5/8” button head bolt and hardware. (Fig. B)INSTALLATION:NOTE: Tailgate table can be installed either inside tailgate or outside of tailgate.Fig. AFig. B97-288AR300Q BadgeTable Top 93-288AR300ABottle Opener 93-288AR300XTable Top 93-288AR300AStep 5: Drop the cup holder brackets (93-288AR300K) into place and secure to the tail gate table top (93-288AR300A) mounting holes using (4) supplied 10-24 X 1/4” button head bolts and hardware. (Fig. C)Step 6: Install the round rubber bumpers (9540K921) to the to the swing out arm (93-288AR300L drvr and 93-288AR300U pass) mounting holes using the (2) supplied 10-24 X 3/4” button head bolt and hardware. Step 7: Install the push-in rubber bumpers (8638T43) to the to the swing out arms (93-288AR300L drvr and 93-288AR300U pass) by pressing into the mounting holes.Step 8: Install the swing out arms (93-288AR300L and 93-288AR300U) into the mounts on the tailgate mount (93-288AR300N) using the (2 per side) supplied 6mm X 80mm button head bolts, (4 per side) 1/4” nylon flange sleeve washers and hardware . (Fig. D)Fig. CFig. DTable Top 93-288AR300ACup Holder Bracket 93-288AR300K10-24 X 1/4” BoltTable Top 93-288AR300ACup Holder Bracket 93-288AR300K10-24 X 1/4” BoltTailgate Mount 93-288AR300NSwing Out Arm 93-288AR300L and93-288AR300U6mm X 80mm Bolt and Nylon Flange Sleeve Washers6mm X 80mm Bolt and Nylon Flange Sleeve WashersStep 9: Install the tailgate mount (93-288AR300N) to the table top (93-288AR300A) using (2) supplied 1/4”-20 X 1” bolts and hardware. Do not fully tighten 1/4”-20 hardware.NOTE: This is the location is where table top will pivot. Open and close tailgate table and keep tightening hardware until you feel slight drag. (Fig. E)Outside Mounting Installation Instructions:Step 1: Remove the spare tire and unbolt and remove the OE rear tire mount from the OE rear gate. (Fig. F)Step 2:Carefully raise tailgate table assembly into position and line up with the existing mounting holes in the OE rear gate. Secure using the (8) supplied 8mm X 35mm button head bolts and hardware. (Fig. G)Fig. EFig. FTable Top 93-288AR300ATailgate Mount93-288AR300N 1/4”-20 X 1” BoltOE Rear GateStep 3: Open and close the tailgate table assembly to ensure smooth movement. Adjust if necessary. (Fig. G)Inside Mounting Installation Instructions:Step 1: Remove the OE plastic trim piece from inside OE rear gate. (Fig. H)IMPORTANT!: Be sure to position the tail gate table assembly to clear the hard top/soft topif applicable. Step 2: Carefully raise the tailgate table assembly into position and mark the holes to be drilled using the tailgate table mount (93-288AR300N) as a drill template. NOTE: Tailgate mount holes are slotted for adjustment. It is recommended to mark the holes in the center of the slots for maximum adjustment.Fig. GFig. HTailgate Table AssemblyOE Rear GateOE Rear GateOE Rear GateStep 3: Remove the tailgate table assembly and center punch the previously applied marks for drilling. (Fig. I)Step 4: From the rear of tailgate, look through the inspection hole and check to make sure marked holes will not interfere with any internal structures. (Fig. J)Step 5: Using a 17/32” drill bit, drill the previously center punched marks. Install the 3/8”-16 threaded inserts into newly drilled holes using a NutSert tool to lock them securely in place. (Fig. H)Step 6:Carefully raise the tailgate table assembly into position and line up with the previ-ously drilled holes in the OE rear gate. Secure using the (8) supplied 3/8” X 1” bolts and hardware.Fig. JFig. IOE Rear Gate OE Rear GateTailgate Table AssemblyInspection HoleProduct cleaning and maintenance instructionsStainless Steel Finish – Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap, window or glass cleaner may be used to clean the finish. Dual state pow-der coat finish – Mild soap, window or glass cleaner may be used to clean the finish. In order to protect the finish, you may wax your product on a regular basis with pure carnauba automotive wax. Do not use any types of soap, polish or was that contains abrasive that could damage the finish. Textured coated finishes should be cleaned with a mild soap on a damp sponge. Do not apply polish or was that requires to be removed by means of buffing. This type of wax is com-monly used at car wash facilities . Chrome Finish – Mild soap, window or glass cleaner may be used to clean the finish. In order to protect the finish you should wax your product on a regularNOTE: Be careful not to overtighten hardware. Nutserts may spin if too much torque is applied. (Fig. J)Step 7: Installation is now complete.Limited WarrantiesSmittybilt’s products are covered under the following limited warranties only. Note that the dura-tion of the limited warranty differs according to the material and finish of the product purchased. Subject to the duration and conditions of the limited warranty stated below, Smittybilt warrants to the original retail purchaser that its products are free from defects in material and workmanship. All other warranties and representations express or implied, are hereby disclaimed, including fit-ness for merchantability and buyer’s intended use or purpose. All parts are sold “AS IS” except for the limited warranties granted herein. Buyer assumes all risks as to the selection, suitability and performance of all goods and products selected. This limited warranty does not cover dam-age or impairment in any part due to misuse, improper installation, accident or contact with on-road or off-road hazards, product modification, improper or inadequate cleaning and/or mainte-nance. Smittybilt is not responsible for items damaged during shipping. This warranty is not transferable from the original buyer. For the original Buyer to be eligible for the limited warranty coverage, the Buyer must provide proof of purchase. Smittybilt strongly recommends returning the warranty registration card.Customer’s remedy hereunder shall be limited only to repair or replacement (at Smittybilt’s op-tion) of any defective part(s) returned to Smittybilt at customer’s expense. The determination of whether or not a returned part is defective or subject to coverage under the limited warranties stated herein shall be made at Smittybilt’s sole discretion.To assure product quality, Smittybilt reserves the right to change product design, material, speci-fication and finishes without prior notice to customers. This limited warranty gives you specific legal rights and you may also have other rights, which may vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply as to you. Also, some states do not allow the exclusion or limitation of incidental or conse-quential damages, so the above limitations or exclusions may not apply to you. Smittybilt re-serves the right to discontinue product lines and substitute products, or provide other remedies than those listed in this limited warranty for those discontinued products.WarningRollover and other types of vehicle accidents may result in serious injury or death to you, your passengers and others sharing the road. Smittybilt accessories are decorative and are not intended to reduce or avoid injury or damage in the event of an accident. The weight and location of Smit-tybilt accessories may affect your vehicles’ handling, stability and performance, creating an in-。
希曼 M、MLB、MDC、MDC LB 折叠式尾门安装说明书
M16, 20, 25, 30attEntiOn inStallERS:Changes are made periodically to the installation procedure to comply with engineering changes. To ensure proper liftgate operation, it is VERY iMPORtant to read and understand the installation instructions before attempting an installation. Installers also MuSt read and understand the liftgate’s Owner’s Manual before installing the liftgate, so they can operate the liftgate safely as required during different stages of the installation process. nEVER perform a modification on the liftgate, which is not specifically covered in the manual or which is unauthorized by Thieman. Modifications may result in failure of the liftgate and may create hazards for liftgate installers, operators, or maintainers. Serious damage, equipment failure, or operator injury could result from improper installation. This equipment MuSt have all decals applied properly. FailuRE to apply all decals properly will VOid all warranties! Any installer with questions or doubts should contact Thieman before proceeding.The M, MLB, MDC, and MDCLB are stow-away style liftgates for use on trucks and trailers. Before mounting your liftgate, make sure that the model you have will work on the truck or trailer you intend to mount it on. The loaded and unloaded bed height of your truck (with weight of liftgate figured in) MuSt fall within the bed height range of your liftgate. T o determine the bed height range of your liftgate, you must know the full model name, the platform material of both the main section and extension (i.e. both steel, both aluminum, or steel main with aluminum extension), and the platform size (see charts and fig-ures on pages 2 thru 4).nOtES:1. The tip of the platform will touch the ground on standard STOW-AWAY liftgates, but not on gates designed for “level ride”. “Ramp ride” is standard, “level ride” is built for special order only.2. Reference figures 1 and 2 for charted dimensions on pages 2 thru 4.3. All maximum mounting dimensions are shown with the vehicle empty; all minimum mounting dimen-sions are shown with the vehicle loaded.4. Check bed height “H” when parked on a level surface.5. Check “C” dimension for possible interference with spring hanger bracket before installation.6. If the liftgate was ordered with the optional 216 receiver kit, use the loaded bed height (Hmin) to determine what set of mounting dimensions to use. Bed height range for 216 Kit is 42" min. (vehicle fully loaded) and 54" max. (vehicle empty).all StEEl PlatFORMS (StEEl Main and ExtEnSiOn) Platform Size Models h a b C d E 32+5All Models 34"-40" 16.50 14.00 32.00 4.00 5.50 38W MLB 16/20 34"-40" 16.50 14.00 32.00 4.00 5.50 36+6M 16/20 37"-44.99" 19.50 17.00 30.50 5.00 8.0045"-50" 22.00 16.00 28.50 5.50 10.0050"-54" 25.00 15.00 25.50 6.50 13.00 36+6M 25/30 38"-44.99" 19.50 17.00 30.50 5.00 8.0045"-50" 22.00 16.00 28.50 5.50 10.0050"-54" 25.00 15.00 25.50 6.50 13.00 42+6All Models 42"-45" 19.50 18.50 30.50 5.00 8.0045"-50" 22.00 17.50 28.50 5.50 10.0050"-54" 25.00 16.50 25.50 6.50 13.00 42+10 RET M 16/20 37"-45" 19.50 17.00 30.50 4.19 6.0045"-50" 22.00 16.50 28.50 4.75 8.0050"-54" 25.00 16.00 25.50 5.50 11.00 42+10 RET M/MDC 25/30 38"-45" 19.50 17.00 30.50 4.19 6.0045"-50" 22.00 16.50 28.50 4.75 8.0050"-54" 25.00 16.00 25.50 5.50 11.00 42W M/MDC 45"-50" 22.00 16.00 28.50 5.50 10.0050"-54" 25.00 15.00 25.50 6.50 13.00A—Distance from top of bed to trunnion tube.B, D, E—Clearance needed for platform in closed position.C—Minimum distance needed for mounting plates.F, G, J, K—Rubrail notch dimension. See figure 2.H—Distance from ground to bed height.StEEl Main SECtiOn/aluMinuM ExtEnSiOn PlatFORMSPlatform Size Models h a b C d E 48W M/MDC25 45"-49.99" 22.00 17.00 28.50 5.50 10.00 50"-54" 25.00 15.00 25.50 6.50 13.0048W MDCLB 25 38"-45" 19.50 17.00 30.50 5.00 8.00all aluMinuM PlatFORMS (aluMinuM Main and ExtEnSiOn)Platform Size Models h a b C d E 27+6MLB 16/20/25 34"-40" 16.50 13.00 32.00 4.50 5.5037W MLB 16/20 34"-40" 16.50 13.00 32.00 4.50 5.5036+6M16/20 37"-44.99" 19.50 18.00 30.50 5.00 8.00 45"-50" 22.00 17.00 28.50 5.50 10.00 50"-54" 25.00 16.00 25.75 6.50 13.0036+6MDC/M25/30 38"-44.99" 19.50 19.00 30.50 5.00 8.00 45"-50" 22.00 18.00 28.50 5.50 10.00 50"-54" 25.00 16.50 25.75 6.50 13.0040+6All Models 42"-45" 19.50 19.00 30.50 5.00 8.00 45"-50" 22.00 18.00 28.75 5.50 10.00 50"-54" 25.00 16.50 26.00 6.50 13.0042+10 RETM 16/20 37"-44.99" 19.50 19.00 30.50 4.50 6.50 45"-50" 22.00 18.00 28.50 5.00 8.50 50"-54" 25.00 16.50 25.75 6.00 11.5042+10 RETM/MDC 25/30 38"-44.99" 19.50 19.00 30.50 4.50 6.50 45"-50" 22.00 18.00 28.50 5.00 8.50 50"-54" 25.00 16.50 25.75 6.00 11.5048W M/MDC 25 45"-49.99" 22.00 18.00 28.50 5.50 10.00 50"-54" 25.00 16.25 25.75 6.50 13.0048W MDCLB 25 39"-45" 19.50 19.00 30.50 5.00 8.00Step 4 Raise the liftgate by lifting under the main section of the folded platform with a forklift.Make sure the platform is clamped securely to the forks. With the trunnion and liftarmshanging from the platform, the platform rib and pivot assembly should make firm contact.The installer may need to rotate the trunnion, as shown, to make this contact. Tack weldthis time, the M series liftgates are pre-assembled with cylinder and pump mounted. Oncertain installations, for instance a truck with a rear fuel tank, the pump may get in theway of obtaining the proper “A” dimension. In most of these cases, Except for the 50" to54" bed height range, where the “A” dimension is 25.00, the pump may be removed andthen mounted to the second, more rearward, set of holes in the pump mounting bracketto provide more clearance. note: do not move pump when the “A” dimension is 25.00because the platform will not stow properly.Step 6 Cut a small post or similar item to the correct length and place it under the platform so the platform and payload area are at the same height. Place barrels or other protectiveequipment under the platform so that the gate will not accidentally fall and injure some-Step 7Attach mounting plates to truck by means of .62" Grade 8 screws or by a .38 fillet weld all around. Weld the mounting plates to the trunnion tube all around in the samemanner.note: On installation where narrow underframe members are used, the liftgate mounting plates will reach these frame members for mounting purposes; however, the spacebetween the frame members and trunnion now becomes quite large. This lengthyunsupported area may contribute to undesirable ‘springiness’ under heavy loading.Many installers when faced with this problem extend the underframe support on themounting plate closer to the trunnion by adding a channel section under the existingframe member as shown in figure 6. On certain equipment such as a lengthened vanbody, rebuilt trailer or other altered vehicle, where the underframe stops short of theend of the vehicle body frame, extra support must be added to avoid any indepen-dent deflection. See figure 7 for bracing suggestions. Refer to figure 1 for clearances.Step 8battery cable from the liftgate toward the circuit breaker. AvOID SHARP CORnERSAnD HIGH HEAT e cable clips provided to secure the cable to the truckframe every 2 ft. Cut the cable to the desired Length and strip .88" of the insulationfrom the end. Slide the pre-cut heat shrink over the end of the cable. Secure thecable lug in a vise and apply heat to the connector and insert the cable as the soldermelts. Allow connector to cool and install the heat shrink. Attach this end to one ter-minal on the 150 amp circuit breaker.Step 9Many late model trucks have battery connections as shown in figure 8. The ground cable from the battery may be connected directly to the engine block with only a lightbraided ground strap connecting the block to the chassis. Where this is the case, thefactory installed cable does not provide an adequate ground circuit for operating bat-tery powered liftgates. We recommend that the cables labeled with an “X” be not lessthan #2 gauge cable as supplied in the installation kit. Also because of the high cur-rent draw (approximately 200A) we recommend that the alternator be a heavy dutytype and the battery must have a 150 AMP minimum reserve capacity.Step 10Install breather cap on power unit and connect hydraulic hose from power unit to flow control. Remove tack weld from Step 4. See figures 9 thru 12 for hose and batterycable connections. On gravity down liftgates, install return line in place of plugson butt end of cylinder and return port on pump reservoir. On Power downliftgates, the rod end port on cylinder must be plumbed to C1 port on pump.(note: Incorrectly plumbing rod end port on cylinder to C2 port will make gate driftdown and motor to spin backwards from raised position.) Attach ground cable to thetapped hole in the pump base labeled “GnD” and to the trunnion mounting plate withthe .38 hardware and internal lockwashers provided.Step 11Locate and mount the toggle switch assembly or pushbutton box in a convenientM series liftgate comes with a standard snubber kit to prevent excessive wear duringtransport. See figure 15 for mounting instructions.Step 13To re-adjust the platforms spring assist, follow these steps: (See figure 16.)1. Fold the platform for stowing and raise until the tension is relieved from springitem C.2. Remove snap ring item A from the groove and slide it to the left.3. Remove the locknut item G from item E.4. Slide spring support tube item B to the left and tilt right side up and remove fromassembly.5. Remove long straight end of closing spring from hole in center rib of platform itemD. Moving the spring to the left decreases the tension and to the right increasesthe tension.6. Return spring support tube to position and replace snap ring.between the platform and main section a shim must be added as shown in figure 17.Step 15now review the entire installation with the power source disconnected. With the power connected again, check for possible interference of all moving parts. If inter-ference occurs review the instructions and contact THIEMAn if the problem can notbe eliminated.Step 16Thieman recommends that the installer perform a weight test of the liftgate to check the welds or mounting bolts and the structural integrity of the body or frame of thetruck or trailer. The load used should be the maximum weight rating of the particularliftgate with the weight centrally located on the platform. A minimum of 20 cyclesshould be made to insure the integrity of the mounting.Step 17Finish paint as required and remove the pre-mask on decals already applied by Thieman. Apply the remaining decals in the appropriate locations as shown. Whenpainting, carefully grease or mask fittings and exposed portion of the piston rod. Thedecals MuSt be applied properly or all warranties are VOid!Step 18Any lights that were removed or obstructed must be replaced or relocated in such a manner that the completed vehicle must be compliance with FMvSS 108 (49 CFR571.108).Step 19It may be necessary to add Rear End Protection on this installation. Check your localand state laws for requirements for FMCSR 49 CFR 393.86.item Part name Part number1 Warning Decal-off center 46710502 Fast Idle Decal 46501502 PTO Decal 46501403 Danger Decal-no riding 46094 Operating Decal 46508905 Capacity Decal-1600# 4650750 5 Capacity Decal-2000# 4650100 5 Capacity Decal-2500# 46501105 Capacity Decal-3000# 46501206 Warning Decal-pinch point 46047 Handle Decal 46058 Thieman nameplate (not shown) 46508009 Urgent Warning Decal 468110 Reflector (3) 570511 Wiring Diagram-Gravity Down 461211 Wiring Diagram-Power Down 461412 Warning Decal 462013 Caution Decal 465077014 Receiver Latch Decal (w/optional 216 Kit) 4683。
现代Casper电尾门安装说明
现代Casper电尾门安装说明
1、现代Casper电尾门安装说明先用小一字螺丝刀撬出卡扣放心撬，是铁的拆底座螺丝就可以拿下撑杆再拆掉上支座电尾门配套的支座。
要分清左右，以及安装方向。
有箭头标识，朝前一定要防水垫安装电尾门撑杆上下支座安装电动撑杆，要分清左右标识。
2、直接按压扣上就行。
另一边一样，在此不再重复从手指示的位置撬饰板，左右都可以。
要用塑料撬棒撬开，再用手稳住劲的拉下来，一定要平稳。
以防损坏饰板卡扣拿下第一块饰板，白色的就是卡扣，拆的时候找好发力点，一定要平稳用力，卡扣一个都不会坏。
拆掉两颗十字螺丝，手指的位置。
左右各一就可以拿下两边饰板拆掉螺丝拉手孔里的螺丝拆掉手指位置的螺丝，左右各一。
就可以拉下饰板。
找好受力点，平稳发力，咔咔的就拉下来了最后一块大饰板就可以拉下来了。
拆掉锁头换上电吸锁从橡胶管中穿线。
3、需要用到穿线器和表板蜡没有表板蜡，用的车蜡。
抹在电线上，穿起来很顺滑。
表板蜡就没有问题已经成功穿线我是从驾驶室开始布线，最后剩余线长都绑扎在尾门里面了。
4、撬开驾驶室的保险丝盒，最好用塑料撬棒。
从上撬开，沿边拉开。
一句话就是要平稳发力，卡扣就不会坏。
取出这个保险丝连接电尾门配套的取电器一根线保险盒插电，一根压在螺丝下面接地接好线试了一下，电尾门可以正常工作。
广汽丰田汽车有限公司 GAC TOYOTA MOTOR CO.,LTD. 电动尾门系统安装说明书
电动尾门系统安装说明书感谢惠购丰田产品*电动尾门系统*这本手册介绍了电动尾门系统的安装方法，安装之前请仔细阅读本手册适用车型2018款汉兰达（两驱精英版、豪华版，四驱精英版、豪华版、骑士版）目录一、安装注意事项 (1)二、构成零件清单 (2)三、安装工具 (2)四、接线概要 (3)五、更换尾门撑杆 (5)六、尾门部分拆装 (7)七、车身部分拆装 (11)八、车身侧走线 (20)九、尾门侧走线 (24)十、线束连接 (26)十一、接线夹使用步骤 (33)十二、安全警示标签粘贴 (34)十三、功能确认 (34)十四、注意 (35)一、安装注意事项承蒙购买电动尾门系统,深表感谢!本说明书叙述电动尾门系统的安装要领。
在安装前,请务必阅读本说明书,以便做到正确安装。
二、构成零件清单三、安装工具电工绝缘胶带套筒扳手、一字螺丝刀、十字螺丝刀、10mm 套筒、14mm 套筒Φ25开口钻美工刀斜口钳尖嘴钳翘板手工电钻四、接线概要1、系统部件流程2、系统线束示意注意：线束安装过程中，接线夹的使用方法在手册第35页查阅。
3、电动尾门COMBOX的安装电动尾门COMBOX的安装位置：如图所示，拆下尾门的内饰板。
找到电动尾门COMBOX安装位置，先将电动尾门COMBOX固定在安装支架上，再用螺栓将电动尾门COMBOX安装至尾上预留的COMBOX安装位置示意图，详细拆装步骤见下文。
4、电动尾门ECU的安装电动尾门ECU的安装位置：如图所示，拆下行李箱左侧的内饰板。
找到行李箱左侧ECU安装位置，先将行李箱左侧ECU固定在安装支架上，再用螺栓将电动尾门ECU安装至行李箱左侧预留的ECU安装位置示意图，详细拆装步骤见下文。
五、更换尾门撑杆1、拆气撑杆1将尾门开到全开状态，并做好支撑；以防止在拆卸气撑杆过程中，尾门向下掉落。
▲不做支撑，可能造成人身伤害！▲为安全起见，需一人支撑尾门，一人更换撑杆，完成两边的气撑杆拆卸后，再更换电撑杆！2用10mm套筒扳手松开气撑杆车身侧支架的两颗固定螺丝并移出。
荣威RX5天鉴电动尾门安装说明书
天鉴电动尾门安装说明书(RX5)电动举升门安装一、注意事项●本说明书中的所有图片仅供参考，图片与实物有可能不同，但安装方法是一样的。
●为方便您安装，请在安装前认真阅读该商品使用说明书；安装时需注意保护好您爱车的表面，避免刮花。
●请定期检查与车连接的所有配件是否松动，以确保使用安全。
编号数量名称编号数量名称编号数量名称1 1 控制盒⑵2 举升杆⑶ 1 电吸锁⑷ 1 拉绳⑸ 1 电吸锁控制盒⑹ 1 线束⑺10 扎带⑻ 1 开孔器⑼ 1 手动开关二、配件清单三、安装步骤参考配件清单和配件图检查配件是否齐全。
首先把尾厢盖板拿开，拆下锁扣盖板拆下尾门内饰板拆下左边穿线胶套两边 用一字螺丝刀把与举升杆与车门连接的头部的卡簧撬开，拆出原车举升杆，拆装过程中需把门顶住把举升杆装在原气弹簧位把产品举升杆装上，注意，带线的一头靠门那一边把举升杆的线从如图所示的胶塞里穿到门内，左右杆的安装方法一样把电源正极线，拉锁控制线通过穿线胶套穿到车身上在穿线套两头打上表板蜡，利于穿线电源正极线从尾厢车顶穿到前面电源正极线从后排迎宾踏板穿到驾驶位电源正极线从驾驶位车顶穿到方向盘左侧处如图所示把保险丝座插到原车的保险丝处，注意保险丝座的方向，电源正极线与保险丝座相接撬开方向盘左侧的饰板把拉锁控制线从尾厢右侧穿下 接插头端子：把线束上的拉锁控制线对应拉锁控制盒的插头插好，注意颜色要一一对应接负极线：如图所示，把负极线接到门上的接线柱上接开门信号线： 如图所示把原车尾门开关接头拔下, 线束棕色线接右边数起第三根蓝黑线，蓝色线接右边数起第一根棕色线拆下原车锁扣装上产品所配的拉锁，用所配的螺丝拧紧，先上左边的螺丝，再上右边的，注意上螺丝前先把长拉簧拆下把长拉簧装上，再把拉绳卡进拉锁的卡槽上，拧紧拉绳螺丝把拉绳另一对与拉锁控制盒相连，拧紧螺丝把控制盒装在门上如图所示的位置，把所有内饰板还原。
最后检查所有螺丝是否全部锁紧通电后首次开关门为控制盒自动学习模式，请确保门能开关到位，至此，电动举升门安装完毕。
10-16款途观电动尾门装车流程图
尾门锁头开关转接线
原车锁头
1、原车尾箱效果图
2、取下尾门上的装饰板和螺丝，按图示 1/2/3/4拆开饰板
3、取下原车撑杆和车身支架与尾门球钉，车身换上我司短球钉；尾门换上我司长球钉， 注意球钉要加上垫片
4、装好我司左撑杆（L杆）与右撑杆（R杆），注意球头帽卡簧要卡到位， 否则会脱杆
5、用22MM的开孔器开孔走撑杆线并装好硅胶塞如图所示
6、拔下原车锁头后面的插头与我司后按键通讯线的插头对插如图所示
7、把尾门开关检测线（紫色线）夹到原车尾门开关插座的1号线上如图所示
8、把电源线、CAN线、前按键线与电吸 9、我司建议在如图位置用22mm开孔器打孔 盒连接线分别走至方向盘左侧和尾箱左后 装上我司通用前按键 方如图所示
10、拆下原车导航，在导航后面的插头上找到橙色和橙棕色线；把我司 CAN-H线夹到橙色线上，CAN-L线夹到橙棕色线上如图所示
6、安装车身支架时要把原车螺丝换成我司所配的平头螺丝，否则会造成尾门关 不到位或掉杆子（具体参考安装流程）
7、撑杆装到原车球钉后要注意把球头帽上的卡簧压到位，否则会引起掉杆子(最 好是用点力把撑杆往外拉看撑杆是否会松脱，如果有松脱现象说明卡簧没卡到位）
8、用取电器取电时，一定要从保险盒B+的大电流保险丝位取电，同时不能影响 原车其它功能的正常使用，地线的位置应保障良好的回路（请按照我司的安装流程 操作）
9、布撑杆连接线打孔时，一定要按照我司的打孔指引标识位置打孔，同时应把 车门适当拉低点以保证钻头与打孔位垂直，否则在打孔过程中可能会引起钻头偏 位，把孔周边的地方搞花
10、布置CAN线、电源线、前按键线、电吸盒连接线时，要把所有线和插头以 最小的面积绑在穿线器上（大插头绑在前，小插头和线绑在后面），且应在原车穿 线管槽里喷些表板蜡以方便穿线（具体布线位置请参考安装流程指引图）
途锐电动尾门安装方法
途锐电动尾门安装方法
1. 首先，根据车型和尾门型号，选择适合的电动尾门装置。
2. 在安装前需要检查车辆的电路和电池，确保电量充足。
3. 着手安装电动尾门的主支架，其位置可能需要依据车型和尾门型号进行调整，要求支架位置最大程度地利用车辆原有结构，以防影响车辆美观和安全。
4. 板件固定支架上。
适当减轻电动尾门的重量，提高安装的可靠性。
5. 根据操作说明书链接电源，连接导线至电池正负极，将控制盒固定在车内，或安装远控模块，这些重要的配件一定要和主支架位置充分配合，避免影响车辆原有结构。
6. 对安装的每个关键部件进行测试，以确保它们能够运作正常，测试的要点包括：控制盒，电缆和电机。
测试时可以依据配件说明书来检验部件的功能和操作流程，如无法使用，需要检查相关配件是否涉及损坏或则电路问题。
7. 完成上述步骤后，将整个尾门与支架进行连接，并进行检查以确保安装的稳定性。
8. 进行最终的测试，测试电动尾门的所有控制器是否正常，检查尾门的打开和
关闭是否平稳无误，再次确认所有部件工作正常之后，方可将尾门安装完毕。
电动尾门（SUV）安装说明书
电动尾门（SUV）安装说明书安装产品前请仔细阅读本安装说明书适配车型：智能双杆电动尾门适配18+款大众探歌产品编号：PW029648零件号：5002171版本：A/0电动尾门安装注意事项：1、为了安全和确保产品正常使用，由销售本产品的专业工作人员或经过培训人员安装，切勿私自拆卸本机，以免造成本产品损坏及事故发生；2、装车前的注意事项：1）与客户沟通：咨询车主尾门是否加装过或改装过，如加装尾灯罩/装饰板/音响等使原车尾门增加重量超过2KG，则不能安装该产品；2）启动发动机，检查并确保：汽车各仪表盘针指显示正常及无故障报警，车内门边开关、遥控钥匙按键灵敏并正常使用，尾门开、关状态能在仪表盘上显示等，如发现有异常及时告知客户；3）保持发动机开启一段时间，确保电瓶有电以便保证电动尾门能够运行；4）关闭发动机，检查并确保：汽车内、外表面完好，原车尾门无左右缝隙大小、高低台阶；5）检查并确保该套电动尾门配件清单的种类、数量齐全；6）安装人员取下身上所携带的金属物品等硬物；3、装车中的注意事项：1）拆下的汽车组件一定要保管好，对可能刮花原车的地方采用贴美纹纸、隔珍珠棉等方式进行保护；2）穿线时，防止尾门/原车线束被划破出现短路的潜在风险；连接线路时，连接头一定要做好绝缘并预留一定的活动空间；各部件需固定牢固；3）安装拉线电动尾门的连接档块时，确保能自由活动；4）连线顺序：各部件先连接，再连常电，最后插ECU（先大后小）4、汽车的清洁、整理：1）安装过程留下的杂物及时处理，不要留在车内；2）对汽车内饰、外观有弄脏的，用干净的布清洁干净；5、汽车启动状态下，请勿插拔各连接部件的接头，以免插拔时损坏原车或部件。
安装说明书免责声明：1、本安装说明书的图片仅供安装方法参考；2、非专业人员或未经培训人员安装的，且未按本安装说明书要求、步骤安装的，出现异常或事故，本公司不负任何责任；本安装说明书最终解释权归广东东箭汽车科技股份有限公司；电动尾门配件清单：量号量2 ○2 21 ○2 11 ○4 216 ○2 11 ○4 111 ○2 110 ○4 11 1电动尾门安装工具清单：1○11○ 1撑杆线束图驱动盒线解码器控制信号线灰色接原车尾门开关控制信号线CAN 信号线 正极负极粉红线接ECU 开关黑色线接解码器安装步骤一：安装门锁1.1把原车后踏盖拆下 1.2拆下原车锁扣组 1.3把我司垫板装上，根据箭头朝向正确安装，用原车螺母把垫板平行拧紧1.4安装门锁组，用两颗内六角沉头螺栓配合门锁专用垫圈拧紧螺丝；注意：安装时根据开关门的缝隙上下移动锁扣调整至合适位置1.5门锁驱动盒，安装好后需隐藏 1.6驱动盒按图示装入消音盒1.7驱动盒装入消音盒后，将其捆绑好，如图所示1.8 如图示意为驱动盒安装位置 1.9装有驱动盒的消音盒，放置在备胎的尾门方向左侧，需固定好，防止行车时松动安装步骤二：安装撑杆1.10用扎带把拉线固定好，防止拉线与盖板、钣金摩擦；把我司配的后踏盖安装（图片仅供参考）1.11复原安装后踏盖2.1拆原车气弹簧：把原车左右两边气弹簧拆卸，提示：拆原车撑杆时需有人撑起尾门，防止掉下；2.2拆下右侧原车下支架 2.3图为拆下的原车下支架2.4保留原车固定头2.5 用我司配的下支架右安装，原车螺栓复原拧紧 2.6把我司撑杆如图示意卡进原车固定头内，并确保卡稳，如图右侧已装好，左侧同样安装2.7左电机穿线孔：拆下原车盖板后，看到此原车孔，用于穿电机线，把胶塞装上，防止进水2.8右电机穿线孔：在撑杆圆圈位置钻φ19的孔，撑杆线束穿过，胶塞卡紧并用封口胶封口； 2.9接撑杆电机插头端子：对应颜色线插进凹槽内，白色对应插槽白色，棕色对应棕色，把上面的黄色小卡块摘下移到下面卡紧；注意车头车头车头车头车头安装步骤三：接线、布线2.10另外一束线：绿色对绿色，蓝色对蓝色，灰色对灰色，红色对红色，然后用接头的黄色卡片推进卡槽把线稳固；2.11插头端子连接完成，轻轻摇晃接头，确定线束对接稳固；3.1接开关、门信号线、左右撑杆线束分布到尾门对应位置，ECU 放置在尾箱右侧3.2把我司（左右撑杆线束、门锁信号线、开关信号线）线束从此处波纹管穿过引至尾门上3.3布正极线：将正极延着虚线引至左C 柱；（同时布解码器控制信号线）3.4布正极线：将连接正极的线如图所示，通过尾箱后，把左C 柱及迎宾踏板掀开线穿过将正极线引至B 柱；（同时布解码器控制信号线）3.5布正极线：把正极线从B 柱引至前门迎宾踏板隐藏；（虚线）（同时布解码器控制信号线） 3.6布正极线：在驾驶室中控台装饰件， 看到原车保险盒3.7安装ECU ：把主线束插头对应安装到ECU 上， 先大后小的顺序接上3.8安装ECU ：安装ECU ：撕走魔术贴上的3M 离型纸，贴在ECU 背部3.9安装ECU ：与ECU 接头对接，并把ECU 装在右侧装饰板内空旷处, 可自行调整3.10接门锁信号线：拆下原车尾门上门盖板后，看到原车门锁连接器3.11接门锁信号线：上门锁扣背后如图此位置拆下原车插头连接器，注意如图拍摄角度3.12接门锁信号线：用我们配的转接线连接，再把我司转接线插头（箭头）插进上门锁；注意如图拍摄角度3.13接正极线：在驾驶室中控台拆下面板，3.14接正极线：把正极取电器接驳；3.15接正极线：把两个白色端口对插；3.16接解码器正极：把我司解码器线束中的正极（黄色线），如图示意连接到取电器内；3.17拆下保险丝，把黄色线铜丝如图插入保险丝取电器内；3.18把保险丝还原安装回去，线束用电工胶布包扎，如图示意解码器正确线已安装好在取电器里；3.19接正极：在驾驶室中控台保险盒预留孔用试电笔测出常电孔位3.20接正极：放大图示意位置 3.21接正极：用保险丝取电器插上,注意取电器插头方向正确插入取电，如图示意正确安装3.22接负极：在右侧装饰板内找到原车有搭线的负极连接螺栓柱，把我们的负极线搭上3.23接负极：松动螺母，卡进负极连接片，卡紧后再还原拧紧螺母3.24解码器负极：用解码器负极接此箭头位置连接负极3.25所有线束接好后把解码器放在主驾驶室A柱内侧位置固定好3.26接解码器信号线：在驾驶室左下角把盖板取下，找到我们要接的线束，（箭头）解码器安装在此处内部固定好防止松动3.27接解码器信号线：如图角度正视图内正确找到原车黑色线束3.28接解码器信号线：原车线束拆下黑色胶布3.29接解码器信号线：橙绿色接绿黑色橙棕接绿色3.30接解码器信号线：橙棕线为CAN-L要和解码器线束中的绿黑线相接，橙绿色线为CAN-H要和解码器线束中的绿线相接3.31接控制信号线：在尾门车标按键位置，按照3.33方式寻找控制信号线方法找到控制信号线3.32接控制信号线：接上我司解码器线束上的灰色线3.33如果遇到连接器中控制信号线的颜色和说明书描述的不同可以按照以下方法查找控制信号线：控制信号线找线方法：试电笔的夹子头搭铁，试电笔的笔头和所要量的线保持良好接触，此时试电笔灯常亮；手动按下后尾门的按钮，试电笔的灯灭一下；手按着后尾门按钮不放开试电笔的灯常灭；则，此线为控制信号线！安装步骤四：安装零部件、还原内饰3.34控制线的接线方法：解码器线束中的控制线（粉色线）需要和尾门开关按钮三根线中的黑色线相接，相接的时候连接点尽量靠近ECU 的连接器，控制线要和其他线束加固好； 3.35在手抓的小内饰件上打孔，选择无干涉的方便操作的地方，优先考虑左侧，方便操作 3.36在盖板背面此对应位置开孔安装中控开关 3.37注意内饰板后面的空间能够容纳开关的插头 3.38拆下内饰，根据中控开关，在内饰板上用定位片定位后开一个φ19mm 的孔 3.39中控开关装上*底胶*以减少空隙4.1拆下原车上尾门此位置用于安装开关按钮 4.2开关按钮装上，再安装在原车上 4.3如图示意已安装好 4.4安装蜂鸣器：与ECU 接头对接，并把蜂鸣器装在装饰板内空旷处； 4.5检查安装的螺钉是否全部锁紧，检查所有拆卸的装饰件是否全部锁紧，安装完成本安装说明书所有权归广东东箭汽车科技股份有限公司所有，未经本公司预先书面同意，严禁复制全部或部分内容作为商业用途。
马克森SL-20A SL-30A电动液压尾门操作手册说明书
1
MAXON Lift Corp. 11921 Slauson Ave Santa Fe Springs, CA 90670
(800) 227-4116
2
3
4
5
5. Comply with all attached instruction decals and warning decals.
6. Keep decals clean and legible. If decals are defaced or missing have them replaced. Get free replacement decals from Maxon.
2. Do not exceed rated load capacity of the Liftgates which is 2000 lbs. for model SL-20 and 3000 lbs. for model SL-30.
3. Do not allow any part of your body to be placed under, within, or around any portion of the moving Liftgate or its mechanisms, or in a position that would trap them between the platform and the floor of truck body (or between platform and the ground) when Liftgate is operated.
沃尔沃S90电动尾门安装说明书
电动尾门（摆臂）安装说明书安装产品前请仔细阅读本安装说明书适配车型：智能电动尾门适配18+款沃尔沃S90（摆臂）产品编号：PW026559零件号：5002024版本：A/0电动尾门安装注意事项：1、为了安全和确保产品正常使用，由销售本产品的专业工作人员或经过培训人员安装，切勿私自拆卸本机，以免造成本产品损坏及事故发生；2、装车前的注意事项：1）与客户沟通：咨询车主尾门是否加装过或改装过，如加装尾灯罩/装饰板/音响等使原车尾门增加重量超过2KG，则不能安装该产品；2）启动发动机，检查并确保：汽车各仪表盘针指显示正常及无故障报警，车内门边开关、遥控钥匙按键灵敏并正常使用，尾门开、关状态能在仪表盘上显示等，如发现有异常及时告知客户；3）保持发动机开启一段时间，确保电瓶有电以便保证电动尾门能够运行；4）关闭发动机，检查并确保：汽车内、外表面完好，原车尾门无左右缝隙大小、高低台阶；5）检查并确保该套电动尾门配件清单的种类、数量齐全；6）安装人员取下身上所携带的金属物品等硬物；3、装车中的注意事项：1）拆下的汽车组件一定要保管好，对可能刮花原车的地方采用贴美纹纸、隔珍珠棉等方式进行保护；2）穿线时，防止尾门/原车线束被划破出现短路的潜在风险；连接线路时，连接头一定要做好绝缘并预留一定的活动空间；各部件需固定牢固；3）安装拉线电动尾门的连接档块时，确保能自由活动；4）连线顺序：各部件先连接，再连常电，最后插ECU（先大后小）；4、汽车的清洁、整理：1）安装过程留下的杂物及时处理，不要留在车内；2）对汽车内饰、外观有弄脏的，用干净的布清洁干净；5、汽车启动状态下，请勿插拔各连接部件的接头，以免插拔时损坏原车或部件。
安装说明书免责声明：1、本安装说明书的图片有可能与实物不一致，但安装方法一致；2、非专业人员或未经培训人员安装的，且未按本安装说明书要求、步骤安装的，出现异常或事故，本公司不负任何责任；本安装说明书最终解释权归广东东箭汽车科技股份有限公司；电动尾门配件清单：量号量1 ○2 11 ○4 111 ○2 11 ○4 11 ○2 11 ○4 11 ○6 11 ○2 31 ○4 51 ○6 1电动尾门安装工具清单：1○11 ○ 14○8 32○10 21安装步骤一：拆装门锁1.2掀开原车尾箱盖板 后踏盖上有一个小灯和一个传感器信号接线，可先抬起后踏盖脱离钣金, 然后拆下这两个连接线首先把我司小后踏盖与门锁组安装好，箭头的卡扣连接好 1.11我司小后踏盖拆下原车锁扣1.4把门锁组装在原车上，用原车螺栓复原安装，1.5门锁驱动盒，安装好后需隐藏1.6驱动盒按图示装入消音盒1.7装好合上，把拉线露出外面1.8把包装好的驱动盒安装在如图空旷位置，需固定好，防止行车时松动1.1拆下后踏盖上固定螺丝，双手把后踏盖从底处轻轻搬起，拆下原车尾箱盖板，左侧盖板取下后踏盖安装步骤二：安装支架 、气撑杆1.9拉线固定好，防止干涉把原先拔下线插头先安装回去，原车插头放大示意图原车插头需复原安装最后还原安装后踏盖2.1把左边内侧装饰件拆下，并妥善保管好，后续还原安装,注意防止尾门掉下2.2 图中画圈的3个孔是支架的安装孔。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
天鉴电动尾门
安装说明书(自由光)
电动举升门安装
一、注意事项
●本说明书中的所有图片仅供参考，图片与实物有可能不同，但安装方法是一样的。
●为方便您安装，请在安装前认真阅读该商品使用说明书；安装时需注意保护好您爱车的表面，避免刮花。
●请定期检查与车连接的所有配件是否松动，以确保使用安全。
编号数
量
名称
编
号
数
量
名称
编
号
数
量
名称
1 1 控制盒⑵
2 举升杆⑶ 1 电吸锁
⑷ 1 拉绳⑸ 1 电吸锁控制盒⑹ 1 线束
⑺10 扎带⑻ 1 开孔器⑼ 1 手动开关二、配件清单
三、安装步骤
参考配件清单和配件图检查配件是否齐全。
首先把尾厢盖板及遮物帘拿开
拿出备胎，并拆开后盖板（箭头所示）
拆开左边侧饰板
拆下尾门内饰板
拆下左边穿线胶套两边 用一字螺丝刀把与举升杆与车门连接的头部的卡簧撬开，拆出原车举升杆，拆装过程中需把门顶住
拆下原车气弹簧的车身支架的两个螺丝
安装产品所配的万向头，另一个螺丝孔位用拆下的螺丝拧上
把产品举升杆装上，注
意，带线的一头靠门那一边
把举升杆的线 从如图所示的胶塞里穿到门内
把电源正极线，解锁信
号线，解码线与拉锁控制线通过穿线胶套穿到车身上
在穿线套两头打上表板蜡，利于穿线
解锁信号线，电源正极线与解码线从尾厢车顶穿到前面
电源正极线与解码线从后排迎宾踏板穿到驾驶位
、
把电源正极线与保险
丝座相连，保险丝座插入驾驶位方向盘下的
保险丝盒上，如图所示，注意保险丝座的方
向
如图所示，解锁信号线
（黄色线）接B 柱上如图的接头右边从上数起
第六根黄色线
把负极线接到如图所示
尾门上的螺丝上，
注意要接在螺丝头与垫片中间
如图所示，解码线与
OBD 线相连，再把
OBD 线插入原车OBD 接口
把拔下的公接头接到
线束的母接头，再把线束的公接头插到原车
的母接头上
把原车锁机上的插头拔
下
把所配的开关装到如图所示位置
开门开关线接尾门上的开关按钮处，如图所示，把接头拔下，把拔下的公接头接到线束的母接头，再把线束的公接头插到原车的母接头上
把控制盒放于尾门上，用所配的魔术贴固定
好。
把所有内饰板还原。
最后检查所有内饰
是否全部锁紧；
通电后首次开关门为控制盒自动学习模式，请确保门能开关到位，至此，电动举升门安装完毕。
四、免责声明：由于安装及使用不当而引发的相关问题及损失，不在我公
司的质保范围内。
感谢您购买智能电动举升门，在使用前请仔细阅读本手册，阅后请小心收藏，以备日后才查阅.图片仅供参考，产品以实物为准。