数码管规格书
3621数码管规格书
3621数码管规格书数码管是一种常见的显示装置，能够在电子设备中显示数字、字母和符号等信息。
3621数码管是一种常见的七段数码管，它由七个发光二极管组成，并且可以显示数字0-9以及一些字母和符号。
3621数码管的规格如下：1. 尺寸：3621数码管的尺寸通常为10mm x 20mm x 7mm。
尺寸的设计使得它适用于各种电子设备中，既能显示清晰的数字和字符，又不会占用太多的空间。
2. 亮度：3621数码管通常具有高亮度的特点，能够在各种环境光线条件下清晰可见。
这使得它特别适用于室外或者光线较暗的场合。
3. 电源电压：3621数码管的工作电压通常为3-5V，这使得它能够与各种电子设备中的电源兼容，并且能够满足不同设备的电源需求。
4. 工作电流：3621数码管的工作电流通常在15-20mA左右。
这个电流相对较小，使得数码管在工作时能够保持较低的能耗。
5. 显示模式：3621数码管可以显示数字0-9以及一些字母和符号，如A、B、C、D、E、F等。
它采用七段显示的方式，通过控制各个发光二极管的导通与否来显示不同的数字和字符。
6. 刷新率：3621数码管的刷新率通常在50Hz-200Hz之间。
刷新率越高，显示的数字和字符越稳定，不易出现闪烁的情况。
7. 视角：3621数码管的视角通常为120度。
这意味着无论从哪个角度观察数码管，都能够清晰地看到显示的内容，不易受到视角限制。
总结起来，3621数码管是一种常见的七段数码管，具有尺寸小、亮度高、工作电压适配性好、能源消耗低、显示模式多样等特点。
它可以在各种电子设备中使用，用于显示数字、字母和符号等信息。
无论是室内还是室外，无论是亮光还是暗光环境，3621数码管都能够提供清晰可见的显示效果。
同时，它的视角范围广，能够从多个角度观察内容，使得信息传达更加方便。
总体来说，3621数码管是一种性能稳定、可靠性高的显示装置，在各个领域中都有广泛的应用。
中山市晶明光电科技有限公司彩屏白光数码管产品规格书说明书
产品名称:12*15产品型号:JMF-4473BP3-59P6.8 Product No:样品单号：Sample NO:注：所有材料均符合All materials制作:何宗儒Author:客户:Customer:机型:Model No:料号:Part No:结论:版本VersionA/1产品说明书( 1.极限参数（（1）粉色(Pink功耗（Power直流电流（Continuous 反向电压（Reverse工作温度（Operating 储藏温度（Storage抗静电电压（2.光电特性（（1）粉色(Pink光颜Emitting color粉色Pink3.结构尺寸（5.面膜效果图：不贴膜！6.注意事项(6.1储存(Storage数码管为湿敏元器件，5—30℃，湿度用，超过六个月后则要库存不得超过The LED Displaythe use andmore,all ofre-testing,andcan be put intomachine shall每个数码管产品包装箱里面都放置无钴予处理方案，除湿条件There are HUMIDITYhumidity cardtime or inform6.2焊接(Welding产品在过波峰焊时，温度不得超过During the wave-soldering,The wave soldering图1手动焊接产品焊接点至少要距离产品实体 1.6mm以上，烙铁需在30W以下，温度不得超过300℃，时间不得超过3秒The solderingshould be lessseconds.7.外观要求（序号项目1针孔、汽泡Pinholes,2杂物/刮伤Scratch/other3变形Out of4印章不良Bad print5PIN排距Row pitch8.发光效果要求（序项目Items号发光颜色Emitting色差Chromaticaberration发光不均Unevenluminance膜纸漏光Filmlight-leaking。
数码管规格参数
先介绍一下5161数码管的类型：数码管按段数分为七段数码管和八段数码管，八段数码管比七段数码管多一个发光二极管单元（多一个小数点显示），本实验所使用的是八段数码管。
数码管的连接方式分为共阳极数码管和共阴极数码管。
本实验用到是共阴极数码管。
（一般情况下在元器件上能看到以下几种型号：5161AS:共阴红色；5161AG:共阴绿色；5161BS:共阳红色；5161BG:共阳绿色）本实验用到的元器件为：5161AS八段一位数码管*1；220Ω直插电阻*8；面包板及面包板跳线；图一图二（共阴）图三（共阳）数码管共有七段显示数字的段，还有一个显示小数点的段。
当让数码管显示数字时，只要将相应的段点亮即可。
例如：让数码管显示数字1，则将b、c 段点亮即可。
将每个数字写成一个子程序。
在主程序中每隔1s 显示一个数字，让数码管循环显示0～9 数字。
每一个数字显示的时间由延时时间来决定，时间设置的大些，显示的时间就长些，时间设置的小些，显示的时间就短。
实验代码：//设置控制各段的数字IO 脚int a=7;//定义数字接口7 连接a 段数码管int b=6;// 定义数字接口6 连接b 段数码管int c=5;// 定义数字接口5 连接c 段数码管int d=10;// 定义数字接口10 连接d 段数码管int e=11;// 定义数字接口11 连接e 段数码管int f=8;// 定义数字接口8 连接f 段数码管int g=9;// 定义数字接口9 连接g 段数码管int dp=4;// 定义数字接口4 连接dp 段数码管void digital_0(void) //显示数字0{unsigned char j;for(j=5;j<=11;j++)digitalWrite(j,HIGH);digitalWrite(dp,LOW);digitalWrite(g,LOW);}void digital_1(void) //显示数字1{unsigned char j;digitalWrite(c,HIGH);//给数字接口5 引脚高电平，点亮c 段digitalWrite(b,HIGH);//点亮b 段for(j=7;j<=11;j++)//熄灭其余段digitalWrite(j,LOW);digitalWrite(dp,LOW);//熄灭小数点DP 段}void digital_2(void) //显示数字2{unsigned char j;digitalWrite(b,HIGH);digitalWrite(a,HIGH);for(j=9;j<=11;j++)digitalWrite(j,HIGH);digitalWrite(dp,LOW);digitalWrite(c,LOW);digitalWrite(f,LOW);}void digital_3(void) //显示数字3 {unsigned char j;digitalWrite(g,HIGH);digitalWrite(d,HIGH);for(j=5;j<=7;j++)digitalWrite(j,HIGH);digitalWrite(dp,LOW);digitalWrite(f,LOW);digitalWrite(e,LOW);}void digital_4(void) //显示数字4 {digitalWrite(c,HIGH);digitalWrite(b,HIGH);digitalWrite(f,HIGH);digitalWrite(g,HIGH);digitalWrite(dp,LOW);digitalWrite(a,LOW);digitalWrite(e,LOW);digitalWrite(d,LOW);}void digital_5(void) //显示数字5 {unsigned char j;for(j=7;j<=9;j++)digitalWrite(j,HIGH);digitalWrite(c,HIGH);digitalWrite(d,HIGH);digitalWrite(dp,LOW);digitalWrite(b,LOW);digitalWrite(e,LOW);}void digital_6(void) //显示数字6 {unsigned char j;for(j=7;j<=11;j++)digitalWrite(j,HIGH);digitalWrite(c,HIGH);digitalWrite(dp,LOW);digitalWrite(b,LOW);}void digital_7(void) //显示数字7 {unsigned char j;digitalWrite(j,HIGH);digitalWrite(dp,LOW);for(j=8;j<=11;j++)digitalWrite(j,LOW);}void digital_8(void) //显示数字8 {unsigned char j;for(j=5;j<=11;j++)digitalWrite(j,HIGH);digitalWrite(dp,LOW);}void digital_9(void) //显示数字9 {unsigned char j;for(j=5;j<=11;j++)digitalWrite(j,HIGH);digitalWrite(dp,LOW);digitalWrite(e,LOW);}void setup(){int i;//定义变量pinMode(i,OUTPUT);//设置4～11 引脚为输出模式}void loop(){while(1){digital_0();//显示数字0delay(1000);//延时1sdigital_1();//显示数字1delay(1000);//延时1sdigital_2();//显示数字2delay(1000); //延时1sdigital_3();//显示数字3delay(1000); //延时1sdigital_4();//显示数字4delay(1000); //延时1sdigital_5();//显示数字5delay(1000); //延时1sdigital_6();//显示数字6delay(1000); //延时1sdigital_7();//显示数字7delay(1000); //延时1sdigital_8();//显示数字8delay(1000); //延时1s digital_9();//显示数字9 delay(1000); //延时1s }}实验截图：=================以下资料来源于网络==================按发光二极管单元连接方式分为共阳极数码管和共阴极数码管。
5寸数码管规格书
Parameters.
4
50 011 B
1 2 6.50 ( 5 . 0＂) 1 3 9 . 50 0.8 1 3 0 . 00
69.40
10
11. 8
104.50
F E
A GB
D DeCPlectronics
co.,ltd
xsm
15.90 6.9 ±0.5
ain.asp 5.08*4=20.32
规格书
Specifications
品名 Name
1 位数码管 1 Digit Seven Segments LED Display
型号 Model
发光颜色 Color 8 字高度
“8” Height
总芯片数 Total LED Chips
XSM-S50011A (共阴 Share Cathode)
XSM-S50011B (共阳 Share Anode)
z 冲驱动)功耗率是-0.75mW/℃。产品的工作电流不能大于对应工作温度条件 Ifm 或 Ifp 的 60%。 .s For operation above 25℃,The Ifm Ifp & Pd must be derated,the Current derating is-0.36Ma/℃ for DC w drive and -0.86mA/℃ for pulse drive,the power dissipation is -0.75mW/℃.The product working current ww must not more than the 60% of the Ifm or Ifp according to the working temperature.
1，8
桥格拉夫 GEN8 V3 HD LED数码管产品数据手册 DS435说明书
Product Data Sheet DS435V Series™ HD LED array product, an ultra-high lumen density COB product line, is designed for high intensity spotlights used in commercial and retail settings. V Series HD arrays offer industry leading color over angle uniformity, and replace ceramic metal halide lamps by providing equal or greater center beam candle power at lower power and at greater lifetimes. Their tight beam control and exceptional quality of light is well suited for demanding directional spot applications.The V3 HD LED array is available in a variety of CCT and CRI combinations providing substantial design flexibility and energy efficiencies.Lighting system designs incorporating these LED arrays deliver increased system level efficacy and longer service life. Typical applications include, but are not limited to, commercial and residential down lights, accent, spot and track lights.Bridgelux Décor Series™ is our state of the art color line designed specifically for premium applications, producing unmatched LED light quality with brilliant color-rendering options and offer pleasing and inspiring lighting palettes. Bridgelux Décor Series color points are available on Vero® SE Series, Vero® Series, V Series™ and V Series™ HD.Décor Series™ Ultra products provide a high CRI of 97 and a minimum R9 value of 91, which emphasizes the reds and color tones to which the human eye is most receptive - perfect for the most luxurious retail shops and world renowned museums. Décor Series Ultra is designed as a replacement for halogen.Features• Efficacy of 101 lm/W typical• Compact high flux density light source• Uniform high quality illumination• Minimum 80, 90 and 95 CRI options• Streamlined thermal path• ENERGY STAR® / ANSI compliant color binning structure with 3 SDCM options• More energy efficient than incandescent, halogen and fluorescent lamps• Low voltage DC operation• Instant light with unlimited dimmingBenefits• Enhanced optical control• Clean white light without pixelation• High quality true color reproduction• Significantly reduced thermal resistance and increased operating temperatures• Uniform consistent white light• Lower operating costs• Easy to use with daylight and motion detectors to enable increased energy savings• Reduced maintenance costs• Environmentally friendly, no disposal issueContentsProduct Feature Map2 Product Nomenclature2 Product Selection Guide3 Performance at Commonly Used Drive Currents5 Electrical Characteristics7 Absolute Maximum Ratings8 Performance Curves9 Typical Radiation Pattern10 Typical Color Spectrum11 Mechanical Dimensions12 Color Binning Information13 Packaging and Labeling14 Design Resources15 Precautions16 Disclaimers16 About Bridgelux17Product Feature MapProduct NomenclatureThe part number designation for Bridgelux V Series HD LED arrays is explained as follows:1 2 3 45 67 8 9 10 11 –12 – 13 14Product FamilyCCT Bin Options3 = 3 SDCMCRIE = 80 CRI min. G = 90 CRI min.H = 97 CRI typ.Array Configuration27 = 2,700K 30 = 3,000K 35 = 3,500K 40 = 4,000K 50 = 5,000K56 = 5,600KBXRH – 30 E 0400– C – 8 3Gen. 8Nominal CCTFlux Indicator 0400= 400 lmBridgelux arrays are fully engineered devices thatprovide consistent thermal and optical performance on an engineered mechanical platform. The V Series HD arrays are the most compact chip-on-board devices across all of Bridgelux’s LED Array products.The arrays incorporate several features to simplify design integration and assembly. Please visit for more information on the V Series HD family of products.Emitting Surface (LES)Solder PadsWhite ring around LESCase Temperature (T c Measurement PointProduct Selection GuideThe following product configurations are available:Table 1: Selection Guide, Pulsed Measurement Data (T j = T c= 25°C)1. Nominal CCT as defined by ANSI C78.377-2011.2. CRI values are typical for Decor Series Ultra . CRI values are minimums for all other products. Minimum R9 value for 80 CRI products is 0, the minimum R9 values for 90 CRI products is 50, Minimum R9 value for 95 CRI products is 91 on 2700K and 3000K,and it is 85 on 3500K /4000K/5000K and 5700K. Bridgelux maintains a ± 3 tolerance on R9 values .3. Drive current is referred to as nominal drive current.4. Products tested under pulsed condition (10ms pulse width) at nominal drive current where T j (junction temperature) = T c (case temperature) = 25°C.5. Typical performance values are provided as a reference only and are not a guarantee of performance.6. Bridgelux maintains a ±7% tolerance on flux measurements.Product Selection GuideTable 2:Selection Guide, Stabilized DC Performance (T= 85°C) 4,5Notes for Table 2:1. Nominal CCT as defined by ANSI C78.377-2011.2. All CRI values are measured at Tj = Tc= 25°C. CRI values are typical for Decor Series Ultra . CRI values are minimums for all other products. Minimum R9value for 80 CRI products is 0, the minimum R9 values for 90 CRI products is 50, Minimum R9 value for 95 CRI products is 91 on 2700K and 3000K,and it is85 on 3500K /4000K/5000K and 5700K. Bridgelux maintains a ± 3 tolerance on R9 values.3. Drive current is referred to as nominal drive current.4. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.5. Typical performance is estimated based on operation under DC (direct current) with LED array mounted onto a heat sink with thermal interfacematerial and the case temperature maintained at 85°C. Based on Bridgelux test setup, values may vary depending on the thermal design of the luminaire and/or the exposed environment to which the product is subjected.6. Minimum flux values at elevated temperatures are provided for reference only and are not guaranteed by 100% production testing. Based on Bridgelux testsetup, values may vary depending on the thermal design of the luminaire and/or the exposed environment to which the product is subjected.Performance at Commonly Used Drive CurrentsV Series HD LED arrays are tested to the specifications shown using the nominal drive currents in Table 1. V Series HD LED arrays may also be driven at other drive currents dependent on specific application design requirements. The performance at any drive current can be derived from the current vs. voltage characteristics shown in Figure 1 and the flux vs. current characteristics shown in Figures 2. The performance at commonly used drive currents is summarized in Table 3.Product Performance at Commonly Used Drive CurrentsTable 3:1. Alternate drive currents are provided for reference only and are not a guarantee of performance.2. Bridgelux maintains a ± 7% tolerance on flux measurements.3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.Performance at Commonly Used Drive Currents Product Performance at Commonly Used Drive Currents (Continued)Table 3:1. Alternate drive currents are provided for reference only and are not a guarantee of performance.2. Bridgelux maintains a ± 7% tolerance on flux measurements.3. Typical stabilized DC performance values are provided as reference only and are not a guarantee of performance.Electrical CharacteristicsElectrical CharacteristicsTable 4:Notes for Table 4:= 25°C. Pulse width is 10ms.1. Parts are tested in pulsed conditions, Tc2. Voltage minimum and maximum are provided for reference only and are not a guarantee of performance.3. Bridgelux maintains a tester tolerance of ± 0.10V on forward voltage measurements.4. Typical coefficient of forward voltage tolerance is ± 0.1mV for nominal current.5. Thermal resistance values are based from test data of a 3000K 80 CRI product.6. Thermal resistance value was calculated using total electrical input power; optical power was not subtracted from input power. The thermal interfacematerial used during testing is not included in the thermal resistance value.Absolute Maximum RatingsNotes for Table 5:1. For IEC 62717 requirement, please consult your Bridgelux sales representative.2. Refer to Bridgelux Application Note AN101: Handling and Assembly of Bridgelux V Series LED Arrays.3. Arrays may be driven at higher currents however lumen maintenance may be reduced, and product warranty will be void.4. Light emitting diodes are not designed to be driven in reverse voltage and will not produce light under this condition. Maximum rating provided for reference only.5. Operating Case Temperature 105°C is with drive current ≤500mA. When drive current is Maximum drive current,Operating Case Temperature should be limited with ≤85°C.Table 5: Maximum RatingsFigure 3: Typical DC Flux vs. Case TemperatureFigure 1: HD3 Drive Current vs. Voltage (T j = T c = 25°C)1Figure 2: HD3 Typical Relative Luminous Flux vs. Drive Current (T= T = 25°C)1Figure 4: Typical DC ccx Shift vs. Case TemperatureFigure 5: Typical DC ccy Shift vs. Case TemperaturePerformance CurvesNotes for Figures 1 - 5:1. Bridgelux does not recommend driving high power LEDs at low currents. Doing so may produce unpredictable results. Pulse width modulation (PWM) is recommended for dimming effects.2. Characteristics shown for 3000K and 90 CRI.Typical Radiation PatternFigure 6: Typical Spatial Radiation PatternFigure 7:Typical Polar Radiation PatternNotes for Figure 6:1. Typical viewing angle is 120⁰.2.The viewing angle is defined as the off axis angle from the centerline where intensity is ½ of the peak value.Typical Color Spectrum Figure 8: Typical Color SpectrumNotes for Figure 8:1. Color spectra measured at nominal current for Tj = Tc= 25°C.2. Color spectra shown is 2700K and 90 CRI.3. Color spectra shown is 3000K and 90 CRI.Mechanical DimensionsFigure 9: Drawing for HD3 LED Array1. Drawings are not to scale.2. Drawing dimensions are in millimeters.3. Unless otherwise specified, tolerances are ±0.1mm.4. Solder pad labeled “+” denotes positive contact.5. Refer to Application Notes AN101 for product handling, mounting and heat sink recommendations.6. The optical center of the LED Array is nominally defined by the mechanical center of the array to a tolerance of ± 0.2mm.7. Bridgelux maintains a flatness of 0.10mm across the mounting surface of the array.Color Binning InformationTable 6: Warm and Neutral White xy Bin Coordinates and Associated Typical CCTFigure 10:Warm and Neutral White Test Bins in xy Color SpaceNote: Pulsed Test Conditions, T c = 85°C1. Bridgelux maintains a tolerance of +/- 0.007 on x and y color coordinates in the CIE 1931 color Space.Figure 11: V3 HD Packaging TubeNotes for Figure 11:1. Each tube holds 40 V3 HD COB arrays.2. One tube is sealed in an anti-static bag. Four bags are placed in a shipping box. Depending on quantities ordered, a bigger shipping box, containing four boxes may be used to ship products.3. Each bag and box is to be labeled as shown above.4. Dimensions for each tube are 14.3 (W) x 8.3(H) x 530 (L) mm. Dimensions for the anti-static bag are 75 (W) x 615 (L) x 0.075 (T) mm. Dimensions for theshipping box are 58.7 x 13.3 x 7.9 cmBXRH-30E0300-A-8340150Figure 12: V Series HD Product LabelingBridgelux COB arrays have laser markings on the back side of the substrate to help with product identification. In addition to the product identification markings, Bridgelux COB arrays also contain markings for internal Bridgelux manufacturing use only. The image below shows which markings are for customer use and which ones are for Bridgelux internal use only. The Bridgelux internal manufacturing markings are subject to change without notice, however these will not impact the form, function or performance of the COB array.Customer Use- 2D BarcodeScannable barcode providesproduct part number and otherBridgelux internal productioninformation.Customer Use- Product part numberDesign ResourcesDisclaimersPrecautionsApplication NotesBridgelux has developed a comprehensive set of application notes and design resources to assistcustomers in successfully designing with the V Series HD product family of LED array products. For all available application notes visit . Optical Source ModelsOptical source models and ray set files are available for all Bridgelux products. For a list of available formats, visit .MINOR PRODUCT CHANGE POLICYThe rigorous qualification testing on products offered by Bridgelux provides performance assurance. Slight cosmetic changes that do not affect form, fit, or function may occur as Bridgelux continues product optimization.CAUTION: CHEMICAL EXPOSURE HAZARDExposure to some chemicals commonly used in luminaire manufacturing and assembly can cause damage to the LED array. Please consult Bridgelux Application Note AN101 for additional information.CAUTION: RISK OF BURNDo not touch the V Series HD LED array during operation. Allow the array to cool for a sufficient period of time before handling. The V Series HD LED array may reach elevated temperatures such that could burn skin when touched.3D CAD ModelsThree dimensional CAD models depicting the product outline of all Bridgelux V Series HD LED arrays areavailable in both IGS and STEP formats. Please contact your Bridgelux sales representative for assistance.LM80LM80 testing has been completed and the LM80 report is now available. Please contact your Bridgelux sales rep -resentative for LM-80 report.STANDARD TEST CONDITIONSUnless otherwise stated, array testing is performed at the nominal drive current.CAUTIONCONTACT WITH LIGHT EMITTING SURFACE (LES) Avoid any contact with the LES. Do not touch the LES of the LED array or apply stress to the LES (yellow phosphor resin area). Contact may cause damage to the LED array.Optics and reflectors must not be mounted in contact with the LES (yellow phosphor resin area).About Bridgelux: Bridging Light and Life™© 2021 Bridgelux, Inc. All rights reserved. Product specifications are subject to change without notice. Bridgelux, the Bridgelux stylized logo design, Vero, V Series and V Series HD are registered trademarks, and Decor Series is a trademark of Bridgelux, Inc. All other trademarks are the property of their respective owners.Bridgelux V3 HD Array Series Product Data Sheet DS435 Rev. A (01/2022)46410 Fremont Boulevard Fremont, CA 94538 U.S.A.Tel (925) At Bridgelux, we help companies, industries and people experience the power and possibility of light. Since 2002, we’ve designed LED solutions that are high performing, energy efficient, cost effective and easy to integrate. Our focus is on light’s impact on human behavior, delivering products that create better environments, experiences and returns—both experiential and financial. And our patented technology drives new platforms for commercial and industrial luminaires.For more information about the company, please visit /Bridgelux /Bridgelux/user/Bridgelux/company/bridgelux-inc-_2WeChat ID: BridgeluxInChina。
数码管规格书
参数规格书（2011年版）一、概述护栏管灯又名"LED数码管"，因其常装入护栏上亮化环境而得名。
集先进的微电脑数码控制技术、RGB（红绿蓝）三基色显示技术及军工塑胶壳体为一体，辅以PCB电路板及相关电子元器件混合有序设计，是迄今为止的高科技灯具之一。
以其丰富色彩、节能环保、轻便安全、长寿、防水、耐寒、耐高温及易于安装的特点，深受亮化工程商的青睐。
本产品特别适合户外使用，是国家指定取代霓虹灯的最佳产品之一。
真六段外控就是每条管里有受控的六个单元，每个单元的RGB 灯可单独或组合在接受控制器数据进行灰度变化而呈现出各种各样的色彩变化；帖片真六段外控是指里面的LED灯是SMD(小型化)封装。
元件脚不用穿透线路板，而是表贴在线路板表面的一种形式。
二、用贴片元器件生产LED护栏管的优点A:由于线路板整体厚度降低，LED灯离管壳距离加长，所以R，G，B三色LED混色更好，色彩更柔和。
B:零件的小型化和规则化更容易进行防水处理，比如刷防水胶或灌胶。
C:机器贴装电子元件，不会出现普通插件元件难以防止的虚焊假焊等现象。
D:线路板组装完成后表面整洁，元件端正，批量生产避免了人为因素产生的故障。
外观高档，抗弯曲度提高。
E：贴片LED 灯珠为纯自动化生产，质量比较常规草帽灯更稳定耐用。
三、对接线定义◆大二芯信号线的蓝色线为-----DATA◆大二芯信号线的棕色线为------GND◆小二芯电源的棕色线为---------+24V◆小二芯电源的棕色线为--- -----GND 四、电气参数主要参数如下：产品型号：LED数码管（HLGJZM108-6D-TP）光源颜色：红、蓝、绿（全彩）光源封装：SMD3528 单芯单R、G、B 色LED 数量： 108 粒/米。
可分段数：6 段/ 米。
亮度（LUX）: 1000+/-50LUX发光效率：92％半光衰期：24000 小时电源方式：外置DC 转换电源额定电压：DC24V。
5631数码管规格书
5631数码管规格书摘要：1.概述5631数码管2.5631数码管的规格参数3.5631数码管的应用领域4.5631数码管的选购与使用注意事项正文：一、概述5631数码管5631数码管是一种常见的显示器件，广泛应用于各种数字显示场合。
它的命名来源于其型号，其中“56”代表显示屏的尺寸，即直径为5.6毫米；“31”则表示该数码管有31个引脚。
5631数码管具有体积小、显示清晰、功耗低等优点，成为了许多电子设备的首选显示器件。
二、5631数码管的规格参数1.尺寸：直径5.6毫米，高度约4.5毫米。
2.显示位数：共四位数字，每位数字高6.2毫米。
3.数字间距：0.6毫米。
4.字母间距：0.7毫米。
5.工作电压：1.5V-3.0V。
6.工作温度：-20℃-+70℃。
7.存储温度：-40℃-+85℃。
三、5631数码管的应用领域5631数码管广泛应用于各类电子产品，如电子钟表、智能家居、医疗设备、汽车电子等。
由于其体积小、显示效果好，特别适用于需要紧凑型显示方案的设备。
四、5631数码管的选购与使用注意事项1.在选购5631数码管时，应根据实际应用需求选择合适的尺寸和显示位数。
2.注意查看产品的技术参数，如工作电压、工作温度等，确保选购的数码管能满足设备的性能要求。
3.在使用5631数码管时，应确保供电稳定，避免电压波动对显示效果造成影响。
4.注意数码管的散热，长时间高负荷运行可能导致过热损坏。
5.避免在潮湿环境中使用，以免影响数码管的寿命。
总之，5631数码管作为一种常见的显示器件，在众多电子产品中发挥着重要作用。
选购合适的5631数码管并正确使用，可以确保设备的良好性能。
数码管3461as参数
数码管3461as参数数码管是一种广泛应用于电子设备中的显示器件，它能够通过不同的电信号控制，在显示窗口中显示出数字、字母和符号等信息。
而3461AS数码管是一种常见的七段数码管，我们来详细了解一下它的参数。
一、介绍3461AS数码管是一种七段共阳极数码管，常用于计算机、电子钟、电子仪表、电子游戏等设备中。
它由七个LED发光二极管组成，每个LED发光二极管都能独立控制。
二、外观和尺寸3461AS数码管的外观尺寸为14.22mm x 9.00mm x 8.00mm，整体呈长方形。
它通常采用共阳极结构，即数字显示时需要给相应的引脚加正电压，且LED发光二极管的阳极连接在一起。
三、引脚说明1. 引脚1：片选引脚，用于选择片上的数码管。
2. 引脚2 - 引脚9：a、b、c、d、e、f、g、dp，表示七段数码管的七个段和小数点。
3. 引脚10：公共阳极引脚，用于控制所有数码管的阳极。
四、电气特性1. 工作电流：3461AS数码管的典型工作电流为15mA。
2. 工作电压：正常工作时，3461AS数码管的电压范围为2.5V至3.8V。
3. 最大反向电流：3461AS数码管的最大反向电流为100μA。
4. 工作温度范围：3461AS数码管的工作温度范围为-40℃至+85℃。
五、显示能力1. 数字显示：3461AS数码管可以显示0至9的数字。
2. 字母显示：3461AS数码管可以显示A至F的大写字母。
3. 符号显示：3461AS数码管可以显示一些基本符号，如“-”等。
六、引脚连接使用3461AS数码管时，我们需要将引脚正确连接到电路中。
具体连接方式如下：1. 引脚1连接到片选信号线，用于选择对应的数码管进行显示。
2. 引脚2 - 引脚9分别连接到相应的控制信号线，用于控制七段数码管的每个段的亮灭。
3. 引脚10连接到公共阳极的控制信号线，用于控制数码管显示的亮度。
七、总结3461AS数码管是一种常见的七段共阳极数码管，在各种电子设备中被广泛应用。
方舟 SN460561N 数码管规格书说明书
无锡市方舟科技电子有限公司WUXI ARK TECHNOLOGY ELECTRONIC CO.,LTD规格(承认)书Specification for approval※方舟P/N（ARKLED P/N）SN460561N※客户P/N（CUSTOMER P/N）：※产品说明（DESCRIPTION）：1、2、3、※日期（DATE）：2013年05月30日地址：江苏省宜兴市张渚镇金张渚工业区宇龙路6号ADD：NO.6Yulong Road，ZHANGZHU TOWN，YIXING CITY，JIANGSU PROVINCE，P.R.CHINA电话（TEL）：0086-510-8734116187345700传真(FAX)：0086-510-87342800E-mail：**************网址(http)：■产品特征FEATURES：●高可靠性和高稳定性High intensity and reliability●高品质、和低功耗、低成本High quality,Low power requirement and low cost●IC易兼容、易装配IC compatible,Easy assembly●符合RoHS指令要求Meet RoHS EU Directive●人体防静电承受能力2000V（HMB)ESD2000V(HMB)■产品描述DESCRIPTION：●0.56英寸双位数码管0.56Inch DUAL Digits Display●极性共阴Common Cathode●黑面，白胶Black face,white segment●发光颜色Lighting Color：1、红色RED2、3、4、5、●晶片材质1、AlGaInP2、3、4、5、■产品最大绝对参数值（Ta ：25℃）ABSOLUTE MAXIMUM RATINGS AT Ta=25℃：PARAMETER项目SYMBOL符号RED红色UNIT单位Power Dissipation Per Segment功耗PAD50mw Reverse Voltage Per Segment反向耐压VR5V Continuous Forward Current Per Segment最大使用电流IAF20mA Peak Forward Current PerSegment(Duty-0.1,1KHz)最大峰值电流IPF60mAOperating Temperature Range工作温度TOPr-20℃to80℃Storage Temperature Range贮藏温度Tstg-30℃to85℃Lead Soldering Temperature260℃at1.6mm From Body for3second焊接温度260℃/3秒距离胶体1.6mm以上■产品光电参数值（Ta：25℃）ELECTRICAL/OPTICAL CHARACTERISTICS AT Ta=25℃：PARAMETER项目SYMBOL符号TESTCONDITION测试条件Color颜色MIN最小值TYP标准值MAX最大值UNIT单位ForwardVoltage,Per Segment 正向压降VF IF=20mA红色RED1.922.5VReverse Current,Per Segment 反向漏电流IR VR=5V红色RED50μAPeak EmissionWavelength 峰值波长λp IF=20mA红色RED630633637nmLuminous IntensityPer Segment 法向光强IV IF=20mA红色RED232528mcdNOTES:1.All dimensions are in millimeters.(inches)2.Tolerance is±0.25(0.010")unless otherwise specified.。
东莞市光华电子有限公司 SLR403BRA1BD 数码管规格书说明书
Dongguan东莞市光华电子有限公司一、 特点：● 0.4″三位数码管● 红色发光，功耗低、寿命长 ● 黑面白胶，共阳显示 ● 符合欧盟公布RoHS 指令二、 用途：广泛应用于各类家用电器、仪器、仪表等产品中 三、 极限参数（T A =25℃）： 参数名称 符号 数值 单位正向电流 I F 20 mA 反向电压 V R 5 V 工作温度 T OPR -20 ~ +60 ℃ 储存温度 Tstg -25 ~ +85 ℃ 正向脉冲电流I FP60mA* 注：脉冲宽度≤0.1ms ，占空比≤1/10四、 光电参数（T A =25℃）：参数名称 符号 条件 最小值典型值 最大值单位正向电压 V F I F =20mA1.72.0 2.4 V反向电流 I RV R =5V --- --- 50 μA峰值波长 λP I F =20mA --- 648 --- nm 主波长 λd I F =20mA 635 640 645 nm 半波宽度 Δλ I F =20mA --- 20 --- nm 发光强度I V I F =20mA 10 15 22.5 mcd东莞市光华电子有限公司五、 外形尺寸：其余公差：±0.25单位： mm六、线路图：东莞市光华电子有限公司七、特性曲线：正向电流与正向电压正向电流 I F (m A )相对值 O TI F =20m A发光强度与正向电流发光强度与环境温度相对光发强度正向电流降额曲线正向电流 I F (m A )环境温度 TA(℃)环境温度 TA(℃)正向电流 IF(mA)正向电压 VF(V)波长 λ(nm)相对强度相对光谱分布发光强度东莞市光华电子有限公司八、使用注意事项：1、储存：在温度低于30℃，湿度不高于60%RH 的条件下，产品保存期限为12个月。
将产品保存在密封的容器中并附带干燥剂可以在一定程度上延续产品的储存日期。
不良的储存条件会导致产品引脚的腐蚀或产品性能的改变。
数码管参数
LED数码管基本技术参数欢迎您使用本公司产品，公司采用世界一流的自动化生产设备，聚集高素质优秀管理人才，严格执行ISO9001：2000质量管理体系，确保每一件产品、每一个效控制。
始终坚持“以诚为本”、“质量第一”为公司原则，并承接生产各种异型LED灯具和灯饰照明工程。
LED数码管产品说明书：1.电路板底部多加二条底线，电流更稳定，并采用超高亮度芯片及优质电子元器件。
2.公母对接线采用大头芯三道防水圈防水对接线，100%防水。
LED数码管产品说明书:1．单色数码管：电路采用多个电阻限流供电，使LED免受高压电流冲击，有效保护LED延长使用寿命，单色亮度高，颜色纯正，是户内外景观照明的好产品，线路做过特殊的防水，防潮处理，长期使用，线路板不会因潮气而断裂，生锈，产品性能可靠，稳定，有不同的电压、颜色选择。
2．七彩数码管：3．采用进口超高亮度LED芯片及进口PC管材，其基本特性是以RGB三基色及PCB电路板串（并）联混合连接，内置微处理器，执行主机传送的各种程序命令，能使众多光源组合时产生色彩和动态上的变化，有纵向分层追逐扫描、流水、扩张、渐变、同步等几十种变化程序，灯光效果有单色、三色变化、七色变化、三段变化、六段变化、八段变化、十二段变化等循环切换，除了推荐的几十种变化程序外，还可以根据客户的要求随机进行变幻花样的设计，七彩流水型数码管是通过新型的电脑编程控制，使其变化多达几十种，还可以根据客户需求而设定或自动变化。
主要原理：是由红绿蓝三基色混色实现七种颜色的变化，采用输出波形的脉宽调制，即调节LED灯导通的占空比，在扫描速度很快的情况下,利用人眼的视觉惰性达到渐变的效果。
一根灯管能够同时变化出七种不同颜色，并可产生渐变、闪变、扫描、追逐、流水等各种效果，多根灯管一起配合还可以展示图形和文字。
变化时间、变化形式可以任意控制，灯管长度可任意选择（单位：米）。
寿命长，节能环保，光色柔和，亮度高，抗紫外线照射，防水、防潮等优点。
数码管参数
下面列出了最常用产品的价格，供参考。
如果您需要其他种类的产品，烦请电话咨询。
(点击型号可以查看详细资料)型号规格颜色单价说明LG3611AH0.36" 单联共阴红0.95LG3611BH0.36" 单联共阳红0.95LG3611AG0.36" 单联共阴绿1.05LG3611BG0.36" 单联共阳绿1.05LG3621AH0.36" 双联共阴红1.99LG3621BH0.36" 双联共阳红LG3631AH0.36" 三联共阴红2.80LG3631BH0.36" 三联共阳红2.80LG3641AH0.36" 四联共阴红3.90LG3641BH0.36" 四联共阳红3.90LG3911AH0.39" 单联共阴红0.95LG3911BH0.39" 单联共阳红0.95LG3911AG0.39" 单联共阴绿LG3911BG0.39" 单联共阳绿1.05LG3941AH0.39" 四联共阴红4.95带冒号，无小数点LG3941BH0.39" 四联共阳红4.95带冒号，无小数点LG5011AH0.5" 单联共阴红0.70LG5011BSR0.5" 单联共阳红0.70LG5011AG0.5" 单联共阴绿0.75LG5011BG0.5" 单联共阳绿LG5022AH0.5" 双联共阴红1.85LG5022BH0.5" 双联共阳红1.85LG5611A0.56" 单联共阴红0.70LG5611B0.56" 单联共阳红0.70LG5611A0.56" 单联共阴绿0.75LG5611B0.56" 单联共阳绿0.75LG5621AH0.56" 双联共阴红1.85LG5621BH0.56" 双联共阳红1.85LG5631AH0.56" 三联共阴红2.75LG5631BH0.56" 三联共阳红2.75LG5641AH0.56" 四联共阴红4.20不带冒号LG5641BH0.56" 四联共阳红4.20不带冒号LG5641AG0.56" 四联共阴绿4.20不带冒号LG5641BG0.56" 四联共阳绿4.20不带冒号LG5641AH0.56" 四联共阴红4.20带冒号：LG5641BH0.56" 四联共阳红4.20带冒号：LG8011AH0.8" 单联共阴红1.20LG8011BH0.8" 单联共阳红1.20LG10012DH10 段光柱红1.80LG12012DH红3.25φ3 发光管红0.08管体透明发红光φ3 发光管红0.085φ3 发光管黄0.085φ3 发光管绿0.08φ3 发光管白2.20φ3 发光管兰0.70绿0.09φ5 发光管兰0.70φ5 发光管白2.20φ5 发光管黄0.10φ5 发光管红0.10回答者：maya100 - 四级2009-6-6 00:32型号规格颜色单价说明LG3611AH0.36" 单联共阴红0.95LG3611BH红0.95LG3611AG0.36" 单联共阴绿1.05LG3611BG0.36" 单联共阳绿1.05LG3621AH0.36" 双联共阴红1.99LG3621BH0.36" 双联共阳红1.99LG3631AH0.36" 三联共阴红2.80LG3631BH0.36" 三联共阳红2.80LG3641AH红3.90LG3641BH0.36" 四联共阳红3.90LG3911AH0.39" 单联共阴红0.95LG3911BH0.39" 单联共阳红0.95LG3911AG0.39" 单联共阴绿1.05LG3911BG0.39" 单联共阳绿1.05LG3941AH0.39" 四联共阴红4.95带冒号，无小数点LG3941BH0.39" 四联共阳红4.95带冒号，无小数点LG5011AH0.5" 单联共阴红0.70LG5011BSR0.5" 单联共阳红0.70LG5011AG0.5" 单联共阴绿0.75LG5011BG0.5" 单联共阳绿0.75LG5022AH0.5" 双联共阴红1.85LG5022BH0.5" 双联共阳红LG5611A0.56" 单联共阴红0.70LG5611B0.56" 单联共阳红0.70LG5611A0.56" 单联共阴绿0.75LG5611B0.56" 单联共阳绿0.75LG5621AH0.56" 双联共阴红1.85LG5621BH0.56" 双联共阳红1.85LG5631AH0.56" 三联共阴红LG5631BH0.56" 三联共阳红2.75LG5641AH0.56" 四联共阴红4.20不带冒号LG5641BH0.56" 四联共阳红4.20不带冒号LG5641AG0.56" 四联共阴绿4.20不带冒号LG5641BG0.56" 四联共阳绿4.20不带冒号LG5641AH0.56" 四联共阴红4.20带冒号：LG5641BH0.56" 四联共阳红带冒号：LG8011AH0.8" 单联共阴红1.20LG8011BH0.8" 单联共阳红1.20LG10012DH10 段光柱红1.80LG12012DH12 段光柱红3.25φ3 发光管红0.08管体透明发红光φ3 发光管红0.085φ3 发光管黄0.085φ3 发光管绿0.08φ3 发光管白2.20φ3 发光管兰0.70φ5 发光管绿0.09φ5 发光管兰0.70φ5 发光管白2.20φ5 发光管黄0.10φ5 发光管红0.10。
淘宝购买的LED数码管说明书
Dimensions: [mm]detail AScale - 1,5:1157136S12701Schematic:157136S12701157136S12701157136S12701157136S12701157136S12701157136S12701T e m p e r a t u r eT T T 157136S12701Cautions and Warnings:The following conditions apply to all goods within the product series of Optoelectronic Components of Würth Elektronik eiSos GmbH & Co. KG:General:•This optoelectronic component is designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network, etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Optoelectronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. •The optoelectronic component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products also apply to customer specific products.Product specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty.•All other soldering methods are at the customers’ own risk.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the optoelectronic component body, marking or plating. Washing agents may have a negative effect on the long-term functionality of the product.•Using a brush during the cleaning process may break the optoelectronic component body. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting:•If the product is potted in the customer application, the potting material might shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the optoelectronic component body, pins or termination. Expansion could damage the components. We recommend a manual inspection after potting to avoid these effects.Storage Conditions:• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the optoelectronic component to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•For a moisture sensitive component, the storage condition in the original packaging is defined according to IPC/JEDEC-J-STD-033. It is also recommended to return the optoelectronic component to the original moisture proof bag and reseal the moisture proof bag again. •The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Packaging:•The packaging specifications apply only to purchase orders comprising whole packaging units. If the ordered quantity exceeds or is lower than the specified packaging unit, packaging in accordance with the packaging specifications cannot be ensured. Handling:•Violation of the technical product specifications such as exceeding the nominal rated current, will void the warranty.•The product design may influence the automatic optical inspection.•Certain optoelectronic component surfaces consist of soft material. Pressure on the top surface has to be handled carefully to prevent negative influence to the function and reliability of the optoelectronic components.•ESD prevention methods need to be applied for manual handling and processing by machinery.•Resistors for protection are obligatory.•Luminaires in operation may harm human vision or skin on a photo-biological level. Therefore direct light impact shall be avoided. All products are additionally certified as risk groups 0 to 2 according to DIN EN 62471:2008.•In addition to optoelectronic components testing, products incorporating these devices have to comply with the safety precautions given in IEC 60825-1, IEC 62471 and IEC 62778•Please be aware that Products provided in bulk packaging may get bent and might lead to derivations from the mechanical manufacturing tolerances mentioned in our datasheet, which is not considered to be a material defect.Technical specification:•The typical and/or calculated values and graphics of technical parameters can only reflect statistical figures. The actual parameters of each single product, may differ from the typical and/or calculated values or the typical characteristic line.•On each reel, only one bin is sorted and taped. The bin is defined on intensity, chromaticity coordinate or wavelength and forwardWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODPLD001.0022023-05-27DIN ISO 2768-1mDESCRIPTIONWL-T7DS 7 Segments Display THTSingle Digit ORDER CODE157136S12701SIZE/TYPE BUSINESS UNIT STATUS PAGEvoltage.•In order to ensure highest availability, the reel binning of standard deliveries can vary. A single bin cannot be ordered. Please contact us in advance, if you need a particular bin sorting before placing your order.•Test conditions are measured at the typical current with pulse duration < 30ms. •Wavelength tolerance under measurement conditions ± 2nm. •Optical intensity tolerance under measurement conditions ±15%. •Forward voltage tolerance under measurement conditions ± 0.2V.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.However, no responsibility is assumed for inaccuracies or incompleteness.Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 174638 Waldenburg GermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCEPROJECTION METHODPLD001.0022023-05-27DIN ISO 2768-1mDESCRIPTIONWL-T7DS 7 Segments Display THT Single DigitORDER CODE157136S12701SIZE/TYPEBUSINESS UNITSTATUSPAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0*******************CHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODPLD001.0022023-05-27DIN ISO 2768-1mDESCRIPTIONWL-T7DS 7 Segments Display THTSingle Digit ORDER CODE157136S12701SIZE/TYPE BUSINESS UNIT STATUS PAGE0.52"eiPal PCN11/11This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.。
外控6段全彩数码管规格书
LED 护栏管规格书客户名称：产品型号：外控六段护栏管成品编码：RY-RGD-WK6D-108 发光颜色：全彩工作电压：DC24V一、概述（Introduction）LED护栏管采用进口超高亮度LED芯片及进口PC管材，其基本特性是以RGB三基色及PCB电路板串（并）联混合连接，内置微处理器，执行主机传送的各种程序命令，能使众多光源组合时产生色彩和动态上的变化，有纵向分层追逐扫描、流水、扩张、渐变、同步等几十种变化程序，灯光效果有单色、三色变化、七色变化、三段变化、六段变化、八段变化、十二段、十六段、三十二段、四十八段等循环切换，除了推荐的几十种变化程序外，还可以根据客户的要求随机进行变幻花样的设计，七彩流水型数码管是通过新型的电脑编程控制，使其变化多达几十种，还可以根据客户需求而设定或自动变化。
主要原理：是由红绿蓝三基色混色实现七种颜色的变化，采用输出波形的脉宽调制，即调节LED灯导通的占空比，在扫描速度很快的情况下,利用人眼的视觉惰性达到渐变的效果。
一根灯管能够同时变化出七种不同颜色，并可产生渐变、闪变、扫描、追逐、流水等各种效果，多根灯管一起配合还可以展示图形和文字。
变化时间、变化形式可以任意控制，灯管长度可任意选择（单位：米）。
寿命长，节能环保，光色柔和，亮度高，抗紫外线照射，防水、防潮等优点。
产品说明：用数码管装饰建筑物的轮廓，可以起到突出美化亮化建筑物的效果。
应用范围：适用于各种高档娱乐场所、如：政府机关、酒店、KTV、大型广告牌，轮廓、全彩动态图案显示、文字显示、音乐频谱等。
事实证明，它已经成为照明产品中的一只奇葩，绽放在动感都市。
LED guardrail tube imported high brightness LED chip and import PC steel tubes, its basic characteristics is three gezer and PCB RGB string (and) league mixed connection, built-in microprocessors, all sorts of program execution host transmit commands, can make more light combination of generate colour and dynamic change, vertical stratification chasing scanning, water, expansion and synchronization, gradient dozens of change procedures, lighting effects have monochrome, three colors change, seven color change, three sections of change, change, change, erection proudest twelve section, ten proudest, 32 section, forty erection, except as recommended by the circular switching dozens of change outside the program, can also according to the customer's requirements for changing the design of random pattern, colorful water type digital pipe is through the new computer programming control, make its change up to dozens of, can also according to customer demand and set or automatic changes. Main principle: is red, green, blue three colors by seven colors mixed color realize the change, use the output waveform, namely the pulse width modulation adjust LED lamp conduction 390v in scan quickly conditions, the human visual inert achieve gradient effect. A light tube can also change a seven different colors, and can produce change, flicker, scanning, chase, running water, etc. Various kinds of effect, more together can also tube display graphics and text. Change the time, change form can be arbitrary control, tube length can be arbitrarily choose (unit: meters). Long life, energy conservation and environmental protection, light color downy, high brightness, ultraviolet radiation, waterproof, moistureproof, etc.product description: with a digital tube adornment building outline, can rise to highlight the effect of beautification of buildings.Application: suitable for various kinds of high-grade amusement places, such asgovernment agencies, hotels, KTV, large billboards, outline, full-color dynamic design display, text display, music spectrum etc. Facts have proved, it has become one of lighting products strange flower, blossom in dynamic city.二、参数Features●灯管参数项目Item 参数Parameter range规格spec50*37mmLED数量 LED Amount 108PCSLED封装DIPΦ5发光颜色Choice of colors full-color寿命 Lifespan >50000 Hours发光角度180°LED芯片台湾晶元材质进口PC工程塑料[半透明管]工艺超声波,我司国家专利透气孔堵头控制方式外控工作频率50-60HZ净重Net Weight毛重Gross Weight●技术要求technical request项目item 单位units 参数范围Parameter range工作环境温度working environment ℃-200C - 550C适应湿度≤95%储存条件storage condition ℃-30℃~80℃功率 output power W 10输入工作电压 input voltage V DC24V防护等级IP67实物图Picture of real products。
F2454数码管规格书
深圳市丰骏光电科技有限公司SHENZHEN FENG CHUN ELECTRONICS CO.,LTD.样品承认书APPROVAL SHEET客户名称Customer 客户编号Customer NO.客户料号Customer Item 环保封胶样品型号Part TypeF2454AH送样日期Date of Issue 10月17日 2016年Momth Day Year样品数量QTY客户承认签核Customer Approval:○全部承认○部分承认○修改承认核准／日期Proofead/Date 承认／日期Approval/Date备注REMARKS丰骏签核FENG CHUN Signature核准 ( APPROVAL) 确认 (CHECK)＊如蒙承认，请予承认后签回一份，谢谢！Please approval and fax back to our company, Thanks!LED显示屏产品说明书SPECIFICATION OF LED DISPLAY客户确认：——————型号（PART NO.）：F2454AH用途Aplication：外型尺寸Outer Dimension长：Pancl Length：19.8mm宽：Pancl Width：10mm厚：Pancl Thickness：5mm发光颜色：Emitted Color 红电极间距：Lead Pitch 2.54mm一、极限参数：（Absolute Masimum Ratings）项目Item符号Symbol极限值（Max）单位Unit 红色功耗（Power Dissipation）Pd 57 mW 脉冲电流（Peak Forward Current）Ifp 80 mA 直流电流（Continuous Forward Current）Ifm 20 mA 反向电压（Reveerse V oltage）VR 5 V 工作温度（Operating Temperature Range）Topr -40~+80 ℃储藏温度（Storage Temperature Range）Tstg -40~+85 ℃静电电压（STATIC V oltage）Var ------ ------ ------ V二、光电特性（Optical-Electrical Characteristic）（1）红色（RED）参数（Parameter）测试条件TEST CONDITING）符号SymbolsMin Type Max 单位Unit发光强度（Luminous Intemsity）If=20mA IV 55 60 70 Mcd 正向电压（Forward Voltage）If=20mA VF 1.9 2.0 2.03 V 反向电流（Revbrse Current）VR=5V IR - - 100 uA 波长(Peak Wavelength) If=20mA λp620 621 623 nm 带宽(Spectral Bandwidth) If=20mA △λ- 5 nm 查看角度(View Angle) If=20mA 201/2- 60 Deg三、F2454AH Package Dimensions And Internal Circuit Diagram（1）F2454AH PACKAGE DIMENSION 结构图（2）F2454AH INTERNAL CIRCUIT DIAGRAM 电路图四、保存和焊接条件（Storage & Soldering Conditions）:1、注意保存，保存条件不好时，会降低膜片与反射壳（导光板）的粘附力。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
是由红绿蓝三基色混色实现七种颜色的变化，采用输出波形的脉宽调制，即调节LED灯导通的占空比，在扫描速度很快的情况下,利用人眼的视觉惰性达到渐变的效果。一根灯管通过内控芯片，能够分段变化出七种不同颜色，并产生渐变、闪变、扫描、追逐、流水等各种效果，灯管长度可任意选择（单位：米）。抗紫外线照射，防水、防潮。
特点：
可放在PCB电路板上按红绿兰顺序呈直线排列，以专用驱动芯片控制，构成变化无穷的色彩和图形。外壳采用阻燃PC塑料制作，强度高，抗冲击，抗老化，防紫外线，防尘，防潮，防护等级达到IP65。LED护栏管具有功耗小，无热量，耐冲击，长寿命等优点，配合控制器，即可实现流水，渐变，跳变，追逐等效果。如果应用于大面积工程个模拟LED显示屏，模拟显示屏可以提供各种全彩效果及动态显示图像字符，可以采用脱机控制或计算机连接实行同步控制；可以显示各式各样的全彩动态效果。控制系统采用三泰VISS专用灯光编程软件编辑，数码管控制花样更改方便，只需将编辑生成的花样格式文件复制进CF卡即可，数码管控制器可以单独控制，也可多台联机控制，数码管安装编排方式任意，适合各种复杂工程需求。数码管、控制器以及电源等以标准公母插头连接，方便快捷，并具有独特的外形设计，全新的户外防水结构
LED户外亮化（数码管）
规
格
说
明
书
产品名称： LED数码管
生产单位：中山市生辉科技照明灯饰厂
地 址：中山市五桂山长命水爱恩工业园
日 期：2010-01-10
编 写：
刘永生
前言：
LED护栏管是采用优质超高亮LED发光二极管组成，主要用于城市景观美彩作用。本产品具有耗电小(每个不到1W)、无热量、寿命长、耐冲击、可靠性高、节能环保，光色柔和，亮度高等特点。颜色纯正、超长寿命，平均寿命达8万～10万小时。
配合全彩灯管的LED全彩同步视频控制系统
1，产品图片：
二．规格及参数说明
应用范围
特别适合应用于广告牌背景、立交桥、河、湖护栏、建筑物轮廓等大型动感光带之中，可产生彩虹般绚丽的效果。用护栏管装饰建筑物的轮廓，可以起到突出美彩亮化建筑物的效果。事实证明，它已经成为照明产品中的一只奇葩，绽放在动感都市。
产品规格：
直径有:30mm、40mm、50mm、80mm、100mm、110mm，
产品外型：
有圆形、半圆形、D形。外壳有奶白、透明两种。注（底部加铝槽）
适用范围：
广泛应用于各种大厦幕墙、游乐景观装饰照明、各种桥体亮化等场所。
工作电压：
AC 80V-260V 50-60Hz损耗功率：<12W/m工作温度：-35℃～55℃颜色范围：256级灰度全彩
正常寿命：
>80,000小时防护等级：IP65外形尺寸：50mm×1000mm 80mm×L1000mm