全数字双闭环比例换向阀控制器使用说明书
IMT 系列智能型多回转阀门电动装置 使用说明书
（使用产品前请详细阅读本说明书）SM-22IMT系列智能型多回转阀门电动装置IMTEx系列隔爆智能型多回转阀门电动装置使 用 说 明 书TET通二天天津百利二通机械有限公司(原天津市第二通用机械厂)目 录第一部分 机械构造与安装部分 (1)1.概述2.基本技术参数3.主要结构4.与阀门的连接5.润滑6.电气接线7.注意事项第二部分 设定与调试部分 (4)1.电动装置的操作方法2.显示状态说明3.电动装置的调试4.电动装置功能、参数设置5.控制接线方式第三部分 IMT-04～4Ex 隔爆智能型产品附加说明 (15)1.概述2.使用及维护注意事项3.接线盒的出线部位4.装置的接线程序5.其它天二通T ET第一部分 机械构造与安装部分1．概述IMT 系列非侵入式智能型多回转阀门电动装置（以下简称电动装置）用于驱动控制闸阀、截止阀、隔膜阀等阀瓣工作中直线运动的多回转阀门或类似机构。
IMT 系列电动装置也可与减速器组合，形成组合式多回转电动装置或部分回转电动装置。
本《使用说明书》适用IMT 系列普通型电动装置和IMTEx 防爆型电动装置，如有其它特殊功能时将提供相应的附加说明。
2．基本技术参数2.1动力电源：380V、50Hz 三相三线制正弦交流电（特殊电源订货时提出） 2.2外壳防护等级：IMT-04～2、IMT-04～2Ex ： IP68 IMT-3～4、IMT-3～4Ex ：IP67 2.3使用环境温度：-20℃～+70℃（隔爆型-20℃～+60℃） 2.4环境相对湿度：≤90%（25℃时） 2.5海拔高度：≤1000m2.6短时工作：时间定额为 10、15、30min（根据电动机实际负载） 2.7无强烈振动工况2.8工作环境不含强腐蚀性介质和爆炸性混合物气体2.9设定方式：现场磁旋钮开关、遥控器（需要遥控器订货时提出）3．主要结构电动装置由以下主要部件构成：3.1阀门专用电动机：鼠笼式三相异步电动机，适合阀门的载荷特性和使用工况，启动转矩大，转动惯量小，短时工作制。
D3FB型号的PNGK10式比例方向控制阀门说明书
Series D3FBGeneral DescriptionSeries D3FB (NG10) proportional directional valves are available with and without onboard electronics (OBE).D3FB OBE:The digital onboard electronics is situated in a robust metal housing, which allows the usage under rough environmental conditions.The nominal values are factory set. The cable connec-tion to a serial RS232 interface is available as acces-sory.D3FB for external electronics:The parameters can be saved, changed and duplicated in combination with the digital power amplifier PWD00A-400.The valve parameters can be edited with the common ProPxD software for both versions.Series D3FB valves can be ordered with spool/sleeve design (D3FB*0) for maximum precision, as well as spool/body design (D3FB*3) for high nominal flow - see functional limit curves for maximum flow capability.Features• Spool/sleeve and spool/body.• 3 command options for D3FB OBE:+/- 10V , 4…20mA, +/- 20mA• High repeatability from valve to valve.Technical Information D3FB OBED3FB OBED3FBD3FB• Low hysteresis.• Manual override.• Digital onboard electronics.DDirectional Control Size Flow Style Seal SolenoidB WWeight:D3FB 6.5 kg (14.3 lbs.)F0Spool Solenoid Design 3DesignStandardBolt Kit:BK98 (4) 1/4-24x1.625 SHCSBK385 (4) M6x40Design DDirectional ControlSizeFlow StyleSealInput BPlease order plugs separately. See Accessories.Parametrizing cable OBE => RS232 Item no. 40982923FSpool OptionsDesign3Standard* Flow rate for different ∆p per control edge: Qx = QNom.· √ ∆p x∆p Nom.Continued on the next pageSeries D3FBAll performance curves measured with HLP46 at 50°C (122°F).Performance Curves(Electrically set to opening point 10%)Functional Limits100% command signal (symmetric flow). At asymmetric flow a reduced flow limit has to be considered – typically approx. 10% lower.All performance curves measured with HLP46 at 50°C (122°F).Series D3FB (Onboard Electronics)Block Diagrams — WiringCode W511 + PE acc. to EN 175201-804Code F06 + PE acc. to EN 175201-804Code G0, S06 + PE acc. to EN 175201-804Series D3FB (Onboard Electronics) Technical InformationFeatures•Simple editing of all parameters.•Storage and loading of optimized parameter adjustments.•Executable with all Windows® operating systems fromWindows® 95 upwards.•Communication between PC and electronics via serialinterface RS-232.•Simple to use PC user software, free of charge:/euro_hcd– see "Software Downloads"The parametrizing cable may be ordered under item no. 40982923.ProPxD Interface ProgramThe ProPxD software permits comfortable param-eter setting for the module electronics. Via the clearlyarranged entry mask the parameters can be noticedand modified. Storage of complete parameter sets ispossible as well as printout or record as a text file forfurther documentation. Stored parameter sets may beloaded anytime and transmitted to other valves. Insidethe electronics a nonvolatile memory stores the datawith the option for recalling or modification.D3FB*CD3FB*K★Order plugs separately.D3FB*C OBED3FB*E OBE。
Parker B Series 方向控制阀门说明书
aerospaceclimate control electromechanical filtrationfluid & gas handling hydraulics pneumatics process controlsealing & shieldingDirectional Control Valves B SeriesCompact installation dimensions -flexible installationCompact dimensions, direct body porting and integral mounting holes are all features of the B series valve range. Valves may be mounted singly or on compact modular manifolds that can be extended to accomodate changes in the machine control system.High reliabilityValves easily comply with the requirements for component reliability in accordance with EU Machinery Directive standards EN 9 - and EN983.A wide range of solenoid valvesSolenoid operated versions of the B3 & B4 valves are fitted with interface to accept the 15mm wide solenoid and Form C / ISO 15 17 connector. The valve has small installation dimensions, low energy consumption. The B5 is also available with the mm wide solenoid suitable for (EN175301-803 form B) connector.The solenoid operators are available with or without manual overrides.Manifold mountingIEM stackable manifold system is designed to give maximum flexibility to system designers. Individual manifold bases stack together to form lightweight custom length manifold that can easily be modified to accommodate changes to system requirements. Different solenoid connector optionsA large range of solenoid connectors are available with or without suppression, LED and rectifier and complete with moulded lead.MaintenanceAll B series valves have reliable function and long service life. Spare solenoid and repair kits are available.PRODUCTS AND/ORsubsidiaries andthe informationand testing,herein, includingWARNINGSALE CONDITIONSThe items described in this document are available for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. Any sale contract entered into by Parker will be governed by the provisions stated in Parker’s standard terms and conditions of sale (copy available upon request).3The B series valves are fitted with dynamic bi-directional spool seals suitable for vacuum or pressures up to 10 bar.Under pressure radial expansion of the seal occurs to maintain sealing contact with the valve bore.“Wear Compensating System”This sealing method reduces friction gives lower pilot pressures, fast response and less wear. Valves do not require lubrication in operation but they can also be installed in systems that are lubricated.4Flow CharacteristicsB SeriesFlow characteristicsFlow capacities in accordance with ISO6358All pressures = effective pressureThe curves in the diagram below are typical onlyTechnical Data B3Port sizeG1/8Operating pressure. Vacuum - 10 bar Working temperature.Pneumatically operated valves. -10O C to + 50O C Solenoid operated valves. -10O C to + 50O C Response times:Single sol spring return Single sol air spring return 4/ 6ms Double solenoid operated 13/15ms Flow (acc. to ISO 6358) c = .3 b = 0.45 Qn = 13 l/s Qmax = 16 l/sCv = 0.75Technical Data B4Port sizeG1/4Operating pressure. Vacuum - 10 bar Working temperature.Pneumatically operated valves. -10O C to + 50O C Solenoid operated valves. -10O C to + 50O C Response times:Single sol spring return Single sol air spring return 38/38ms Double solenoid operated 3/ 4ms Flow (acc. to ISO 6358) c = 4.56 b = 0.30Qn = 19.5 l/s Qmax = 3 l/sCv = 1.Technical Data B5Port sizeG1/4Operating pressure. Vacuum - 10 bar Working temperature.Pneumatically operated valves. -10O C to + 50O C Solenoid operated valves. -10O C to + 50O C Response times:Single sol spring return Single sol air spring return 38/40ms Double solenoid operated 16/18ms Flow (acc. to ISO 6358) Qn = 4 l/s Qmax = 37 l/sCv = 1.45Directional Control ValvesB SeriesB4 valveValve body Anodised aluminiumSpool Acetal plastic/ Anodised aluminium Piston Acetal plastic /Anodised aluminium LiningReinforced thermoplastic End covers Anodised aluminium Sliding seals Thermoplastic U-rings, O-rings Nitrile rubber End cover sealingsNitrile rubber Push buttom for manual changeoverAcetal plastic End cover screws Stainless steel SpringsStainless steel Mounting screws for solenoidZinc-plated steelB4 AccessoriesIEM manifold Glass filled nylon End platesAnodised aluminium Manifold connecting screwsZinc plated steelB3 valveValve body Anodised aluminium End covers Anodised aluminium orReinforced thermoplastic Spool Aluminium + nitrile rubberPistonAcetal plastic/ Anodised aluminium U-rings, O-rings Nitrile rubber End cover sealings Nitrile rubber End cover screws Stainless steelSprings Dacromet ® - processed steel,Stainless steel Mounting screws for solenoidStainless steelB3 AccessoriesIEM manifold Glass filled nylon End platesAnodised aluminium Manifold connecting screwsZinc plated steelB5 valveValve body Anodised aluminiumSpool Aluminium + nitrile rubber Piston Brass LiningBrassEnd covers Anodised aluminium Sliding seals Thermoplastic U-rings, O-rings Nitrile rubber End cover sealings Nitrile rubber End cover screws Stainless steel SpringsStainless steel Mounting screws for solenoidZinc plated steelB5 AccessoriesIEM manifold Glass filled nylon End platesAnodised aluminium Manifold connecting screwsZinc plated steel6Metal Spool ValvesB3• G1/8 ports, 3/ , 5/ and 5/3 functions • Inlet-exhaust manifold facility • DIN rail mounting • Integral mounting holes • 1. watt solenoid actuators • FormC/ISO15 17 connector7Metal Spool ValvesB3Main data for Directional control valves, B3 SeriesSymbol Actuator Return Signal pressure Changeover Weight Voltage Order codeQtymin, bar time, ms Kg at 6 bar at 6 baractua./return actua./returnAirAir3,0/3,0 1 /1 0,10 B395000XXH 1Vented centre Self centring positionAir Air 3,0/3,01 /10,10B305000XXH1Pressurised Self centringcentre positionElectric Air 1,4/1/4 9/3 0,13 4 VDC B3S5BB549H 1 0,09 Less solenoid B3S5BXXXXH 1 Electric Air 1,4/1/4 9/3 0,14 4 VDC B3A5BB549H 1 0,10 Less solenoid B3A5BXXXXH 1Metal Spool Valves B3 Main data for Directional control valves, B3 SeriesSymbol Actuator Return Signal pressure Changeover Weight Voltage Order code Qtymin, bar time, ms Kgat 6 bar at 6 baractua./return actua./returnElectric Electric 3,0/3,0 1 /1 0,18 4 VDC B365BB549H 1Vented centre Self centring0,09 Less solenoid B365BXXXXH 1 positionElectric Electric 3,0/3,0 1 /1 0,10 4 VDC B375BB549H 1Pressurised Self centring 0,09 Less solenoid B375BXXXXH 1centre positionInternal air supply to differential pilots and solenoids via port 1Silencers and push-in fittings are shown on page 7.Valves supplied with solenoid operators include standard P8C-D connector89Metal Spool ValvesB3Inlet Exhaust Manifolds for B3 series valvesStandard Base without Flow Controls Each kit contains:1 pcs Manifold Basepcs Mounting screws and nuts 3 pcs Tie Rods1 pcs Body-to-base Gasket and 1 pcs Base-to-Base GasketEnd platesStandard End Plates may be used with either of aboveManifold BasesEach kit contains:1 right and 1 left End Plate 3 pcs O-Rings3 pcs Blanking Plugs3 pcs Socket Head Cap Screws 3 pcs Flat Washers 3 pcs LockwashersIsolator Plug KitUsed to isolate the 1, 3 or 5 gallerybetween two Manifold Bases Each kit contains:3 pcs Isolator Plugs complete with O-rings.Manifold Blanking Plate Each kit contains:1 pcs Cover Platepcs Mounting Screws 1 pcs GasketUsed to blank off unused stations.Order code QtyOrder code QtyOrder code QtyMetal Spool Valves B3 Dimensions, B3 Valve SeriesAll dimensions in mm unless otherwise stated3/2 Body portedSingle solenoid operated air spring return / spring return Double solenoid operatedAir differential return Spring returnA130,5 136,7Air differential return Spring returnB67,0 73,103/2 Inlet Exhaust Manifold For B3 Body Ported ValvesManifolds - IEM Inlet Exhaust Manifold System5/2 Inlet Exhaust Manifold For B3 Body Ported ValvesAll dimensions in mm unless otherwise stated5/3 Body portedDimensions, B3 Valve Series• G1/4 ports, 3/ , 5/ and 5/3 functions • Inlet-exhaust manifold facility • DIN rail mounting • Integral mounting holes • 1. watt solenoid actuators • Form C / ISO 15 17 connectorMain data for Directional control valves, B4 SeriesSymbol Actuator Return Signal pressure Changeover Weight Voltage Order code Qtymin, bar time, ms Kgat 6 bar at 6 baractua./return actua./returnAir Air 3,0/3,0 16/19 0, 04 B496000XXF 1Vented centre Self centringpositionAir Air 3,0/3,0 16/19 0, 04 B406000XXF 1Pressurised Self centringcentre positionElectric Air 1,5/1,5 15/17 0, 0 4 VDC B4S6AB549F 10,170 Less solenoid B4S6AXXXXF 1Electric Air 1,5/1/5 15/17 0, 41 4 VDC B4A6AB549F 10,19 Less solenoid B4A6AXXXXF 1Symbol Actuator Return Signal pressure Changeover Weight Voltage Order code Qtymin, bar time, ms Kgat 6 bar at 6 baractua./return actua./returnElectric Electric 3,0/3,0 16/18 0, 89 4 VDC B466AB549F 1Vented centre Self centring 0,191 Less solenoid B466AXXXXF 1positionElectric Electric 3,0/3,0 16/18 0, 89 4 VDC B476AB549F 1Pressurised Self centring 0,191 Less solenoid B476AXXXXF 1centre positionInternal air supply to differential pilots and solenoids via port 1Silencers and push-in fittings are shown on page 7.Valves supplied with solenoid operators include standard P8C-D connectorInlet Exhaust Manifolds for B4 series valvesStandard Base without Flow Controls Each kit contains:1 pcs Manifold Basepcs Mounting screws and nuts pcs Tie Rods1 pcs Body-to-base Gasket and 1 pcs Base-to-Base GasketEnd platesStandard End Plates may be used with either of aboveManifold BasesEach kit contains:1 right and 1 left End Plate 3 pcs O-Rings3 pcs Blanking Plugspcs Socket Head Cap Screws pcs Flat Washers pcs LockwashersIsolator Plug KitUsed to isolate the 1, 3 or 5 gallery between two Manifold Bases Each kit contains:3 pcs Isolator Plugs complete with O-ringsManifold Blanking plate Each kit contains:1 pcs Cover Platepcs Mounting Screws 1 pcs GasketUsed to blank off unused stations.Order code QtyOrder code Qty Port Size Order code QtyOrder code QtyDimensions, B4 Valve Series3/2 Body portedSingle solenoid operated air spring return / spring returnAll dimensions in mm unless otherwise stated5/2 Body portedSingle solenoid operated air spring return / spring returnSingle solenoid operated air pilot return Single solenoid operated air pilot returnDouble solenoid operated Double solenoid operatedAir differential returnSpring returnA154,0156,0Air differential returnSpring returnB166,0168,0ADimensions, B4 Valve Series3/2 Body portedDouble air pilot operatedAll dimensions in mm unless otherwise stated5/2 Body portedDouble air pilot operatedAir pilot operated air spring return / spring returnAir pilot operated air spring return / spring returnAir differential returnSpring returnC107,5109,5Air differential returnSpring returnD1 0,01 ,0CD5/3 Body portedDouble air pilot return 5/3 Body portedDouble solenoid operated3/2 Inlet Exhaust Manifold For B4 Body Ported ValvesP e r s t a t i o nManifolds - IEM Inlet Exhaust Manifold System5/2 Inlet Exhaust Manifold For B4 Body Ported Valves3348,54,541,510,65837118186,89,58G3/86,6P e r s t a t i o n3348,54,541,510,6599,587,518186,8599,5G3/86,6• G1/4 ports, 3/ , 5/ and 5/3 functions • Inlet-exhaust manifold facility • Integral mounting holes • 5 watt solenoid actuators• EN175301-803 Industrial Form B connectorMain data for Directional control valves, B5 Series (G1/4 threaded ports)Symbol Actuator Return Signal pressure Changeover Weight Voltage Order code Qtymin, bar time, ms Kgat 6 bar at 6 baractua./return actua./returnElectric Electric 3,0/3,0 16/18 0, 89 4 VDC B566BCB49C 1Vented centre Self centring 0,191 Less solenoid B566BCNXXC 1positionElectric Electric 3,0/3,0 16/18 0, 89 4 VDC B576BCB49C 1Pressurised Self centring 0,191 Less solenoid B576BCNXXC 1centre positionOrder solenoid connectors separately, see page 25 for part numbers.Internal air supply to differential pilots and solenoids via port 1Silencers and push-in fittings are shown on page 7.Inlet Exhaust Manifolds for B5 series valvesStandard Base without Flow Controls Each kit contains:1 pcs Manifold Basepcs Mounting screws and nutspcs Tie Rods1 pcs Body-to-base Gasket and1 pcs Base-to-Base GasketEnd platesStandard End Plates may be used with either of above Manifold BasesEach kit contains:1 right and 1 left End Plate3 pcs O-Rings3 pcs Blanking Plugspcs Socket Head Cap Screwspcs Flat Washerspcs LockwashersIsolator Plug KitUsed to isolate the 1, 3 or 5 gallery between two Manifold BasesEach kit contains:3 pcs Isolator Plugs completewith O-ringsManifold Blanking plateEach kit contains:1 pcs Cover Platepcs Mounting Screws1 pcs GasketUsed to blank off unused stations.Order code Qty ManifoldBlanking plateOrder code Qty Isolator Plug kitPort Size Order code QtyOrder code Qty1Metal Spool ValvesB5Dimensions, B5 Valve SeriesAll dimensions in mm unless otherwise stated3/2 Body portedSingle solenoid operated air spring return / spring return5/2 and 5/3 Body portedSingle solenoid operated air spring return / spring returnDouble solenoid operatedDouble solenoid operated2 Position3 PositionA51,16 ,7Metal Spool ValvesB5Manifolds - IEM Inlet Exhaust Manifold System5/2 Inlet Exhaust Manifold For B5 Body Ported ValvesAll dimensions in mm unless otherwise stated6,699,587,59,559G3/845,410,65181830,7P e r S t a t i o n4,53348,53Solenoid Valve OptionsB SeriesValve supplied without solenoidsB3 and B4 valves are designed to accept 15mm solenoid operator / connector CECC/EN 175301-803 Form C/ISO 15 17. Solenoidoperated valves may be ordered without the solenoid operator and connector by substituting XXXX in positions 6 to 9 of the part number. Example B3T5BXXXXH is part number for 5/ Single solenoid operated spring return valve without solenoid operator and standard connector. See Fig 1.B5 valves are designed to accept mm solenoid operator/connector EN175301-803 Industrial Form B. Solenoid valves may be ordered without the coil and connector and are supplied with the solenoid operator fitted to the valve. See Fig .Example B5E6BCNXXC is part number for 5/ Single solenoid operated valve fitted with the solenoid operator having flush locking M/O without coils and connectors.Fig .Fig 1.4Solenoid OperatorsB Series15mm Solenoid Operators for B3 and B4 ValvesElectrical connection EN 175302-803 C/ISO15217 (Ex DIN 43650C)Self tapping screwTorque: .7 - .9 Nm (6 - 8 In. Lbs.)Solenoids 15mm NC, standard(Note! Mounting screws included with basic valve) Voltage WeightOrder code WeightOrder code WeightOrder codeKg Without manual Kg Override, blue, Kg Override, yellow,override non locking flush locking flushSolenoid coils to suit ‘N’ enclosure type22mm 3-Pin EN 175301-803 Industrial Form BCoil Voltage Order code Weight (kg)Solenoid coils for B5 valvesSolenoid Operator Kit for B5 valvesEach kit contains:1 large ‘O’ ring for operator base 1 small ‘O’ ring for operator base mounting screwsSpare solenoid nutsValves with vented exhaust are fitted with diffuser plastic nutSolenoid Valves B SeriesSolenoid Connectors / Cable Plugs EN175301-803Description Order code Order code15mm Form C/ISO15 17 mm Industrial Form BSuitable for B3 & B4 valves Suitable for B5 valves56Solenoid ValvesB SeriesMale straight connectors - Parallel threadTube dia 1 Thread Ordercode Box Qty BFittingsSilencersPort Ordercode Pack QtyCable Plug Dimensions (mm)Solenoid valves P2E-•V ...122Accessories, Service and Replacement PartsCable plugs form C / ISO 15217 for B3 & B4 valves Cable plugs Form B for B5 valvesCable plugs form C / ISO 15217with cables for B3 & B4 valves7Accessories, Services and Replacement PartsB SeriesB3,B4 and B5 Spool/Body repair kits contain:SpoolSpool sealsLip seal – operator pistons GasketsSpool springs Grease packetB3 series valvesManifold gasket kits3/ IEM Gasket kit (10 valve/manifold gaskets)5/ IEM Gasket kit (10 valve/manifold gaskets)B4 series valves5/3 solenoid and remote pilot operated valves – CE Spool/Body repair kit 5/3 solenoid and remote pilot operated valves – PC Spool/Body repair kitManifold gasket Kits.3/ IEM Gasket Kit (10 valve/manifold gaskets)5/ IEM Gasket Kit (10 valve/manifold gaskets)B5 series valves5/3 solenoid and remote pilot operated valves – CE Spool/Body repair kit 5/3 solenoid and remote pilot operated valves – PC Spool/Body repair kitManifold gasket Kits.3/ & 5/ IEM Gasket kit PS 884P (10 valve/manifold gaskets)Solenoid coils for B5 valvesSolenoid coils to suit ‘N’ enclosure type mm 3-Pin Industrial Form BPS2980F PS2981FPS4503F PS4504FSolenoid operator kitEach kit contains:1 Large ‘O’ring for operator base 1 Small ‘O’ ring for operator base PS2884PPS4580F PS4581FPS 2803P PS2804PAE – UAE, Dubai Tel: +971 4 8875600 ********************AR – Argentina, Buenos Aires Tel: +54 3327 44 4129AT – Austria, Wiener Neustadt Tel: +43 (0)2622 23501-0 *************************AT – Eastern Europe, Wiener NeustadtTel: +43 (0)2622 23501 970 ****************************AU – Australia, Castle Hill Tel: +61 (0)2-9634 7777AZ – Azerbaijan, Baku Tel: +994 50 2233 458****************************BE/LX – Belgium, Nivelles Tel: +32 (0)67 280 900*************************BR – Brazil, Cachoeirinha RS Tel: +55 51 3470 9144BY – Belarus, Minsk Tel: +375 17 209 9399*************************CA – Canada, Milton, Ontario Tel: +1 905 693 3000CH – Switzerland, Etoy Tel: +41 (0) 21 821 02 30*****************************CN – China, Shanghai Tel: +86 21 5031 2525CZ – Czech Republic, Klecany Tel: +420 284 083 111*******************************DE – Germany, Kaarst Tel: +49 (0)2131 4016 0*************************DK – Denmark, Ballerup Tel: +45 43 56 04 00*************************ES – Spain, Madrid Tel: +34 902 33 00 01 ***********************FI – Finland, Vantaa Tel: +358 (0)20 753 2500 *************************FR – France, Contamine s/Arve Tel: +33 (0)4 50 25 80 25 ************************GR – Greece, Athens Tel: +30 210 933 6450 ************************HK – Hong Kong Tel: +852 2428 8008HU – Hungary, Budapest Tel: +36 1 220 4155*************************IE – Ireland, Dublin Tel: +353 (0)1 466 6370 *************************IN – India, MumbaiTel: +91 22 6513 7081-85IT – Italy, Corsico (MI) Tel: +39 02 45 19 21 ***********************JP – Japan, Fujisawa Tel: +(81) 4 6635 3050KR – South Korea, Seoul Tel: +82 2 559 0400KZ – Kazakhstan, Almaty Tel: +7 7272 505 800****************************LV – Latvia, Riga Tel: +371 6 745 2601 ************************MX – Mexico, Apodaca Tel: +52 81 8156 6000MY – Malaysia, Subang Jaya Tel: +60 3 5638 1476NL – The Netherlands, OldenzaalTel: +31 (0)541 585 000 ********************NO – Norway, Ski Tel: +47 64 91 10 00************************NZ – New Zealand, Mt Wellington Tel: +64 9 574 1744PL – Poland, Warsaw Tel: +48 (0)22 573 24 00 ************************PT – Portugal, Leca da Palmeira Tel: +351 22 999 7360**************************RO – Romania, Bucharest Tel: +40 21 252 1382*************************RU – Russia, Moscow Tel: +7 495 645-2156************************SE – Sweden, Spånga Tel: +46 (0)8 59 79 50 00 ************************SG – Singapore Tel: +65 6887 6300SK – Slovakia, Banská Bystrica Tel: +421 484 162 252**************************SL – Slovenia, Novo Mesto Tel: +386 7 337 6650**************************TH – Thailand, Bangkok Tel: +662 717 8140TR – Turkey, Istanbul Tel: +90 216 4997081 ************************TW – Taiwan, Taipei Tel: +886 2 2298 8987UA – Ukraine, Kiev Tel +380 44 494 2731*************************UK – United Kingdom, WarwickTel: +44 (0)1926 317 878 ********************US – USA, Cleveland Tel: +1 216 896 3000VE – Venezuela, Caracas Tel: +58 212 238 5422ZA – South Africa, Kempton ParkTel: +27 (0)11 961 0700*****************************Catalogue PDE2582TCUK-ca. Edition February 09Your local authorized Parker distributor© 2008 Parker Hannifin Corporation. All rights reserved.Parker WorldwideEuropean Product Information Centre Free phone: 00 800 27 27 5374(from AT, BE, CH, CZ, DE, EE, ES, FI, FR, IE, IT, PT, SE, SK, UK)Parker Hannifin LtdPneumatic Division Europe The Collins Centre,Lichfield South, Wall Island,Birmingham Road, Lichfield.WS14 0QP United Kingdom Tel.: +44 (0) 1543 483800Fax: +44 (0) 1543 483801/euro_pneumatic。
E02 22 32 比例电磁阀操作说明书
E02/E22/E32系列电磁比例阀操作说明书比例阀参数特性注：Pin1－棕；pin2－白；pin3－蓝；pin4－黑外型尺寸图参数设定――模拟量型常规设定步骤1. 长按3秒“SET”键直至屏幕显示“IS”步骤2. 短按“SET”键进入单位选择界面，此时屏幕显示“U－P”；通过面板上、下箭头按钮可进行显示单位转换。
步骤3. 确定选定的显示单位后，短按“SET”键，存储选定单位并进入零点设定状态。
此时屏幕显示“0”并处于闪烁状态。
步骤4. 通过面板上、下箭头按钮可设置目标的“零点值”（下限压力值），设定范围是全量程的0～50％。
步骤5. 短按“SET”键，存储设定的零点值，并进入跨度设定状态，此时屏幕显示“SP”并处于闪烁状态。
步骤6. 通过面板上、下箭头按钮可设置目标的“跨度值”（上限压力值），设定范围是全量程的10～100％，且必须大于“零点值”。
步骤7. 短按“SET”键，存储设定的跨度值，返回工作状态高级设定步骤1. 长按10秒“SET”键直至屏幕显示“AS”.`步骤2. 短按“SET”键进入模式选择界面，此时屏幕显示“0－S”；通过面板上、下箭头按钮可进行工作模式的转换。
工作模式的确定根据实际的应用而定。
通常地，快速模式响应时间短，而精确模式的响应精度高。
默认为标准模式。
步骤3. 短按“SET”键存储工作模式，且进入反相功能选择模式，此时屏幕显示“Γ□0”。
步骤4. 通过面板上、下箭头按钮可进行反相模式的转换。
“0”为关闭，“1”为开启。
步骤5. 短按“SET”键，存储反相选定状态，返回工作状态。
参数设定――开关量型 常规设定步骤1. 长按3秒“SET ”键直至屏幕显示“IS ”步骤2. 短按“SET ”键进入单位选择界面，此时屏幕显示“U －P ”；通过面板上、下箭头按钮可进行显示单位转换。
步骤3. 确定选定的显示单位后，短按“SET ”键，存储选定单位并进入P1压力设定状态，此时屏幕显示“P1”并处于闪烁状态。
多功能电动阀控制器说明书
IP4 VALVE MIDDLE TRAVEL POSITION SWITCH(No 4)
DSM DIGITAL SWITCH MECHANISM(ELECTRONIC VALVE POSITION AND TORQUE SIGNALS)
46 24
11
B
47 25
(VALVE POSITION SIGNAL)
A
6. THE USER MUST COMPLETE A RISK ASSESSMENT AND IMPLEMENT WHATEVER MEASURES ARE REQUIRED TO ENSURE
A
THAT THE RESULTANT SYSTEM COMPLIES WITH ALL APPLICABLE LEGISLATION.
OTS 8-9 10-11
CLOSED
INTERMEDIATE
OPEN
OPEN by limit switching/CLOSE by torque switching
SWITCH
CTS
4-5 6-7
OTS 8-9 10-11
CLOSED
INTERMEDIATE
OPEN
CLS 12-13
CLS 12-13
2. SEE ACTUATOR USER MANUAL AND DATASHEETS FOR TECHNICAL DATA, PARAMETERS AND DESCRIPTION OF THE ACTUATOR ELECTRIC AND ELECTRONIC EQUIPMENT.
3. IF THE ACTUATOR IS CONFIGURED TO BYPASS THE MOTOR PROTECTION THERMOSTAT (TRM), THE ACTUATOR WILL NO
Air Torque一体式智能比例阀操作说明书
一体式智能比例阀●请仔细阅读本操作手册，然后正确使用●使用之前，请务必先阅读有关注意事项 (3) (3)请仔细地阅读下面的注意事项，并且严格遵守其中的每一条指令。
1word）ID2（高八位））按进入界面继续按继续按直到 Profibus 总线控制，此时再按会增加界面，可以选择PRESS ->FOR 3SC:CONFIG2.Profibus DP LED显示状态PCB主板电源接口：建议将PE口4.Profibus 系统电路连接Sl当定位器在断电或是发生意外情况下，在总线无法控制阀门时，需要定位器的显示元件向左向右键向下键向上键初始化流程说明P=0.0a.若开机显示画面 ， 系统进行初始化才能正常工D:NO INIT按切换为0..20mA：若换，出现连接以后按住3S初始化完成，整个初始化过程需要返回界面成功初始化之后增加界面：切换界面。
调节数值，切换界面。
注意：当P=0.0D: INIT OK进入下一级界面后按切换的界面下按恢复默认值，切换为界面后即退回到上级界面。
三、在初始化成功之后进行各项参数设定：后按切换3S进行初始改变设定值方向说明见参数说明中设定方向）OFF,MIN/MAX, MIN/MIN输出的设定。
LCD显示Min/Min AlarmFun调节10-100，。
设置报警的最大位置。
ERR+RAN, RANGE0-100S。
设置错误时间，即达到错误等级所需要的时间。
错误等级的选择，当错误选项被选择，必须在错误时间内达到错误等级设置的误差内，否则，进行错误输出。
选择错误范围。
即输入信号低于/高于范围报警。
RangeError按（详细说明见参数说明中最小位置和最大位置）按值为100。
（详细说明见参数说明中最小位置和最大位置）no/min/max/min&max为阀门排气至最小位置时实现阀门紧闭，67.6 94.9100 1004 5.67.2调节0.1-10.0，默认值5.0。
Parker D3W 方向控制阀门说明说明书
2-53Catalogue HY11-2500/UKDirectional Control ValveSeries D3W Inductive Position Control2Parker Hannifin GmbH & Co. KG Hydraulic Controls Division Kaarst, GermanyCharacteristics2-54D3W POSITION CONTROL.PMD RHCatalogue HY11-2500/UKDirectional Control ValveSeries D3W Inductive Position Control2Parker Hannifin GmbH & Co. KG Hydraulic Controls Division Kaarst, GermanyOrdering Code3)Only position control code I2 or I54)Only position control code I1 or I42)Only available for styles "E"and "F"2-55Catalogue HY11-2500/UKDirectional Control ValveSeries D3W Inductive Position Control 2Parker Hannifin GmbH & Co. KG Hydraulic Controls Division Kaarst, GermanyOrdering Code2-56D3W POSITION CONTROL.PMD RHCatalogue HY11-2500/UKDirectional Control ValveSeries D3W Inductive Position Control2Parker Hannifin GmbH & Co. KG Hydraulic Controls Division Kaarst, GermanyPosition ControlElectrical characteristics of position control M12x1M12 pin assignment1Normally open 2+ Supply 18...42V 3Normally closed 40V5Earth groundDefinitionsStart position monitored:The valve is de-energized. The inductive switch gives a signal at the moment (below 15% spool stroke) when the spool leaves the spring offset position.End position monitored:The inductive switch gives a signal before ending the stroke (above 85% spool stroke).The switch can only be located opposite the solenoid for direct-controlled valves. This means, if the solenoid is located on the A side of the valve, the switch can only take place on the B side.Protection classIP 65 in accordance with DIN 40050 (plugged and mounted)Ambient temperature [°C]0...+50Supply voltage / ripple[V]18...42 / 10%Current consumption without load[A]≤ 30Max. output current per channel, ohmic [mA]400Min. output load per channel, ohmic [kOhm]100Max. output drop at 0.2A [V]≤ 1.1Max. output drop at 0.4A [V]≤ 1.6EMCEN50081-1 / EN50082-2Max. tolerance ambient field strength [A/m]<1200Min. distance to next AC solenoid [m]>0.1Interface M12x1Wiring min.[mm²] 5 x 0.25 brad shield recommended Wiring length max.[m]50 recommended2-57Catalogue HY11-2500/UKDirectional Control ValveSeries D3W Inductive Position Control2Parker Hannifin GmbH & Co. KG Hydraulic Controls Division Kaarst, GermanyPerformance Curves2-58D3W POSITION CONTROL.PMD RHCatalogue HY11-2500/UKDirectional Control ValveSeries D3W Inductive Position Control2Parker Hannifin GmbH & Co. KG Hydraulic Controls DivisionKaarst, GermanyDimensionsInterface EN 175301-803, DC-solenoid, with plug M12x1*B, E, F -styleAttentionThe switch must be adjusted by the valve manufacturer only. The exchange of individual modules is not permitted.* Delivery includes plug M12 x 1 (see accessories, plug M12x1; order no.: 5004109).The space necessary to remove the plug per EN 175301-803, design type AF is at least 15 mm.The torque for the screw M3 of the plug has to be 0.5 to 0.6 Nm.H, K, M -style。
比例方向控制阀 说明书
15 设计号，10 系列
会改变。对于设计号 10 至 19， 安装尺寸不变。
空白 = 普通手动操作器 H = 防水型ቤተ መጻሕፍቲ ባይዱ动操作器 Z = 无手动操作器
11 电磁铁标识
16 特殊部件
EN47 与 P 型线圈连接和 UNIPLUG 接头一起使用。 不需要时省略
V = 电磁铁 "A" 在先导阀的油口 A 端， 电磁铁 "B"在油口 B 端 ("A" 通电 时从油口 B 给主级供油，"B" 通电 时从油口 A 供油) ：德国惯例
当系统压力低于 200 bar (2900 psi) 时，先导减压 模块可选。 当系统压力高于 200 bar (2900 psi) 时，先导减压 模块必用。
9 先导泄油
M = 用于先导阀的部件和 选项
13 电气数据和连接型式 插头型式符合 ISO4400 (DIN43650)。 线圈特性见 "工作数据" 表 (B.7 页) U-G = 使用带 12V 直流电源的放
大器 U-GP = 使用 12V 电源 U-H = 使用带 24V 直流电源的放
大器 U-HA = 使用 24V 电源 U-HR = 使用 800mA 电源 F-PD7 = 塑料 7 针插头 见下面的警告
14 先导泄油压力
1 = 标准 (见先导泄油应用注意事项，B.9 页)
T = 内部先导泄油 空白 = 外部先导泄油
● 威格士产品的柔性设计使其与多种放大 器，阀选项和阀芯额定值相匹配。
典型剖视图
KDG5V-7 所示不带 “EX” 和 “X” (不带叠加式先导减压阀)
KDG5V-10 所示带有 “EX” 和 “X” (带叠加式先导减压阀)
比例阀使用说明
比例阀使用说明全数字双闭环比例换向阀控制器使用说明书双闭环控制一、概述电路采用32bit高速CPU设计，具有结构简单可靠，参数长时间不会漂移，看门狗设计。
具有模拟量和数字量外部接口设计。
一块控制板可以方便控制比例换向阀，大大简化了常规设计。
二、功能特点1、集成双闭环设计，比例换向阀阀芯位置闭环控制\外部给定反馈闭环控制2、放大器和控制器合二为一，精简设备，减少维护量降低故障率3、具有使用模拟量接口4-20mA（或者0-20mA）反馈、4-20mA（或者0-20mA）（给定与主电路隔离）4、具有数字量接口设计，MODEBUSRS485RTU、CANBUS接口5、可以多个设备进行组网控制，适合多点集中控制6、外部给定反馈闭环控制PID参数调节通过3个电位器调整7、两路阀芯电磁铁控制具有输出过流保护8、看门狗设计，能够及时复位异常工况三、参数1、供电：DC15~30VDC @ 2A2、尺寸123（mm）X160（mm）3、调节精度±1%4、适用范围：华德比例换向阀6通径或10通径带阀芯位置反馈装置进行液压缸、液压缸伸缩位置定位控制，马达行走机构定位控制，液压升降机构定位控制，液压紧紧力装置控制、液压马达行走速度控制等5、工作温度：-30~60摄氏度6、湿度：7、震动：四、典型应用执行机构可以是液压缸，液压马达等执行部件，可以对控制对象进行精准控制五、接线说明六、调整方法此步骤为出厂已经调试好，一般用户无需调整，如果参数确实差异很大，请谨慎操作1、按照接线方法接好线，并认真检查正确后，将控制板上的保险丝去掉，控制板上电后，用万用表的交流档测量COM与L 和COM与R的电压应相同大约在2.3VAC，如果差异大（>0.1VAC）就需要松开位置传感器上的螺丝，将位置传感器的位置通过两个限位螺丝移动，直到测量COM与L 和COM与R的电压应相同为止。
这个步骤一般用户只做检查即可，已经出厂调整过。
成都电气比例阀使用说明
成都电气比例阀使用说明
一、安装和保管
1.安装位置：生产现场应尽量避免直接受到热、湿、粉尘、腐蚀性大的气体、液体等
污染，安装位置应符合电气特性及结构尺寸，以免影响使用效果。
2.保管：设备应放置在干燥、清洁、通风良好、无机械震动和有足够空间的仓库里，
防止受潮、受震动，以免影响使用效果。
二、安装
1.参考技术数据：装置的技术数据应按设计要求正确地安装，以确保正确的使用性能；
2.安装方式：安装应严格按照本说明书和设计要求来进行，采用铰接、螺纹式等结构；
3.余量：安装余量应满足设计要求，余量越大，调节精度越高；
4.检验：安装完毕后，进行位置检查，若发现错误应及时更正；
三、调节
1.根据压力变化：当安装完毕后，按照压力变化调节，保证调节精度；
2.灵活调节：阀门的灵活调节大大增强了比例阀的使用效果；
3.使用状态：使用状态应当满足标准要求，只有如此才能保证比例阀的正常使用；
四、操作
1.手动操作：安装完成后，可以采用手动方式对比例阀进行操作，调节比例阀的压力；
2.注意安全：操作阀门过程中，应注意安全，不要将手放入比例阀内；
3.检修维护：操作完成后，应特别注意对比例阀进行检修维护，以确保比例阀的正常
使用。
整体普通型及整体防爆型多回转阀门电动装置使用说明书
ZB5Z～40Z ZC45Z～1000Z ZB5BZ～40BZ ZC45BZ～1000BZ 整体普通型及整体防爆型多回转阀门电动装置使 用 说 明 书OPERATION INSTRUCTION MANUAL FOR INTEGRATED NORMAL TYPE AND INTEGRATED EXPLOSION-PROOF TYPE MULTI-TURNELECTRIC V ALVE ACTUATORS一、概述General Description整体普通型、整体防爆型多回转阀门电动装置由ZB5~ZB40、ZC45~250及ZB5～ZB40B、ZC45~ZC250B阀门电动装置附加控制电气元件组成，而ZC350~ZC1000BZ由ZC180~250BZ叠加减速装置组成。
本系列阀门电动装置内置控制模块，大容量接触器，可不再使用电控箱，因此具有体积小，功能全（加设了相序自动纠正及缺相保护功能，远程控制有四种方式，另加紧急关阀功能），安装接线简单（只需接入三相动力线，即可现场操作），检修方便（电气回路通过DC24V电压控制，电气部件之间采用接插件连接）等特点。
本产品性能指标达到GB/T24923-2010《普通型阀门电动装置技术条件》的规定，防爆型性能指标达到GB3836.1-2010《爆炸性环境 第1部分：设备 通用要求》、GB3836.2-2010《爆炸性环境 第2部分：由隔爆外壳“d” 保护的设备》及GB/T 24922-2010《隔爆型阀门电动装置技术条件》的规定。
Integrated normal type and integrated explosion type multi-turn electric valve actuators consist of ZB5~ZB40, ZC45~250 and ZB5B~ZB40B, ZC45B~ZC250B electric valve actuators and additional electric control elements. And ZC350~ZC1000BZ actuators are combined with ZC180~250BZ actuators and additional gear reducers. With control module and big capacity contactors built in, these series electric valve actuators need no more electric control box. And so they are small in size and of complete functions (provided with automatic correction of phase sequence, protection of phase-lacking, four modes of remote control, and the function of emergent valve shut in addition), simple in installation and wiring (once the 3-phase power supply is connected, can local operation be carried out), easy to maintain and repair (electric circuit is controlled by DC 24V voltage, electric elements are connected one another with plugs and sockets).Performance index of these products meets with the requirements of Std GB/T24923-2010 TECHNICAL SPECIFICATIONS OF NORMAL ELECTRIC V ALVE ACTUATORS and performance index of explosion-proof type actuators meets with Std GB3836.1—2010ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES—PART I: GENERAL REQUIREMENTS and Std GB3836.1-2010 Explosive atmospheres-Part 1:Equipment-General requirements and Std GB3836.2-2010 Explosive atmospheres-Part 2:Equipment protection by flameproof enclosures“d”and Std GB/T 24922-2010 TECHNICAL SPECIFICATIONS OF FLAMEPROOF ELECTIRIC V ALVE ACTUATORS.二、型号表示方法Representation of TypeMeans integrated model表示防爆型，不标注表示普通型Means max. travel (revolutions)Output speed (r/min)T为推力型，I为电站型，无字母表示Connection mode: T means thrust mode,means connection mode for power station, normalOutput torque (10N·m)ZB或ZC Product type: ZB or ZC例：ZB30T－18/ 40BZ表示输出额定转矩300N·m（30kg·m)推力型，输出转速18r/ min，最大转圈数40，防爆型，整体式。
双闭环直流调速控制模块使用说明书
双闭环直流调速控制模块一、产品介绍双闭环直流调速模块，内含功率晶闸管、移相控制电路、电流传感器、转速与电流双闭环调速电路，可对直流电动机进行速度调节，其方框图见图1。
产品用途：应用于直流电机调速。
产品特点：（１）工艺先进，性能优越①采用进口方芯片，高级芯片支撑板及其它高级热绝缘材料，特殊烧结工艺。
②国外加工专用IC，大大提高智能化控制能力。
③热循环负载次数超过国家标准近10倍，使用寿命长。
④控制电路置于模块内部，简化了外围器件，增强可靠性。
⑤移相控制系统，主电路、导热基板相互隔离，介电强度≥2500V AC。
⑥三相模块主电路交流输入无相序。
（２）质量可靠，应用安全方便①0～10V 直流信号，可对主电路输出电压进行平滑调节。
②给定积分环节可实现直流电机软起动，并且积分时间可调。
③电机起动电流可调节。
④模块具有过流、过热和缺相三种保护。
二、产品种类表 1注：1、规格栏中的电流为模块输出最大直流电流平均值；电压为最高输入工作线电压有效值。
2、全波输出（由于晶闸管不能逆向导通---所以电机只能自行停车）。
3、特殊规格，可按用户要求协议定做。
三、模块内部电联接形式图 2四、输出特性曲线图3 无积分环节电机起动电流、速度波形图（额定负载）图4 有积分环节电机起动电流、速度波形图（额定负载）五、模块的保护1、过流保护模块过流保护可采用外接快速熔断器、快速过电流继电器、传感器的方法。
快速熔断器是最常用的方法，介绍如下：（1）接线方法：快速熔断器接在模块的交流输入端，以三相整流模块和单相整流模快为例，见图5-6：图 5 三相双闭环直流调速模块图6 单相双闭环直流调速模块(2)快速熔断器的选择：①熔断器的额定电压大于电路上正常工作电压。
②熔断器额定电流的选取，参考表3。
表32、过压保护双闭环直流调速模块的过压保护，推荐使用阻容吸收和压敏电阻两种方式并用。
（1）阻容吸收回路电容器把过电压的电磁能量变成静电能量存贮，电阻防止电容与电感产生谐振。
Sun Hydraulics DLDA 2-way 双向操作方向控制阀门说明书
MODELDLDA2-way, solenoid-operated directional spool valve SERIES 1 / CAPACITY: 12 gpm / CAVITY: T-13AX-Control, C-Spool X-Control, H-SpoolM or S-Control, C-Spool M or S-Control, H-SpoolD-Control, C-Spool D-Control, H-SpoolL-Control, C-Spool L-Control, H-SpoolT-Control, C-Spool T-Control, H-SpoolNOTE: DATA MAY VARY BY CONFIGURATION. SEE CONFIGURATION SECTION.This solenoid-operated 2-way, 2-position cartridge is a direct-acting, balanced spool directional valve. The valve is available in either a normally open or normally closed configuration.TECHNICAL DATACavity T-13A Series1Capacity12 gpm Maximum Operating Pressure 5000 psiResponse Time - Typical 50 msMaximum Valve Leakage at 110 SUS (24 cSt) 5 in³/min.@3000 psi Switching Frequency15000 cycles/hrManual Override Force Requirement 5 lbs/1000 psi @ Port 1Manual Override Stroke .10 in.Solenoid Tube Diameter .75 in.Valve Hex Size 7/8 in.Valve Installation Torque 30 - 35 lbf ft Seal kit - Cartridge Buna: 990413007Seal kit - Cartridge EPDM: 990413014Seal kit - Cartridge Viton: 990413006Seal and nut kit - CoilViton: 990770006Model Weight 0.52 lb./DLDANOTESPlease verify cartridge clearance requirements when choosing a Sun manifold. Different valve controls and coils require different clearances.An additional 2.00 inches (50,8 mm) beyond the valve extension is needed for coil installation and removal.C M A /F l o d y n e /H y d r a d y n e ▪ M o t i o n C o n t r o l ▪ H y d r a u l i c ▪ P n e u m a t i c ▪ E l e c t r i c a l ▪ M e c h a n i c a l ▪ (800) 426-5480 ▪ w w w .c m a f h .c o m(X)CONTROLM Manual OverrideD Twist/Lock (Dual) Manual Override L Twist/Lock (Detent) Manual Override TTwist (Momentary) Manual Override(C)SPOOL CONFIGURATIONH Normally Open(N)SEAL MATERIALE EPDM V VitonCOIL *212DIN 43650-Form A, 12 VDC 224DIN 43650-Form A, 24 VDC 712Twin Lead, 12 VDC 724Twin Lead, 24 VDC912Deutsch DT04-2P, 12 VDC 924Deutsch DT04-2P, 24 VDC* Additional coil options are availableMATERIAL/COATINGTECHNICAL FEATURESThe solenoid tube assembly is fatigue rated for 5000 psi (350 bar) service.This valve is direct actuated and requires no minimum hydraulic pressure for operation.On models equipped with the D or L control, the detent mechanism in the manual override is meant for temporary actuation. The D, L and T manual control assembly has a mechanical life expectancy of approximately 7,000 cycles.Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.This cartridge has several manual override choices, including no manual override. See the CONFIGURATION section. Please note: Manual override functionality is not compatible with weatherized coils.This valve utilizes a wet armature design. This means that the working fluid surrounds the armature and is exposed to the heat generated by the coil. This can be a factor if the coil is energized for long periods of time. Some fluids, notably water/glycol mixtures, break down at these temperatures over time and form varnishes that will affect the function of the cartridge.A wide variety of coil termination and voltage options are available, with and without surge protection. See the CONFIGURATION section.The solenoid's unique magnetic design results in a high efficiency solenoid, yielding high spool actuating force per Watt expended, leading to reliable valve shifting.Coils are interchangeable with other Sun Series 1 solenoid products and can be mounted on the tube in either direction.Coil connector options offer ratings up to IP69K. See individual coil product pages for details. Additional weatherized coils and kits are available for more complete environmental protection.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.PERFORMANCE CURVESRELATED MODELSDLDAS 2-way, soft shift, solenoid-operated directional spool valveDLDAZ 2-way, solenoid-operated directional spool valve with position switchModel Code Example: DLDAXCNCONFIGURATION OPTIONSC M A /F l o d y n e /H y d r a d y n e ▪ M o t i o n C o n t r o l ▪ H y d r a u l i c ▪ P n e u m a t i c ▪ E l e c t r i c a l ▪ M e c h a n i c a l ▪ (800) 426-5480 ▪ w w w .c m a f h .c o m。
电动阀门智能控制器说明手册
本定位器出厂之前已对其输入、输出性能进行严格标定， 接线后一般只需标定零、满位即可正常使用，如有任何不明之 处，请与相关技术服务部门联系。 -------------------------------------------------------------------------------------------------产品的不断升级可能导致部分数据的变化，如
四、定位器面板与接线：
10、外形尺寸：
1、定位器面板：
KZQ07-1A
→
74mm(长)x58mm(宽)x38mm(高);
KZQ07-1A 操作面板图
KZQ07-1B
→
mm(长)x48mm(宽)x27mm(高)
61 图
KZQ07-2A 操作面板
11、可通过按键自由标定输入信号所对应执行
面板功能说明
器的动作区间（一般标定为电动参执数行器全
------------------------------------------------------------
-----2 三、 定 位 器 控 制 原 理
------------------------------------------------------------
--4 四、 定 位 器 面 板 与 接 线
到自动状态。
参数设置状态，并保存设定的参数值，返回
自动测控状态。
六、标定接线及操作方法：
（注意：由于电动执行器的应用范围十
诚峰智远全自动多路阀说明书
全自动过滤阀—GA时间型（不带关闭工位）代号：CF：00（LED显示屏）北京诚峰智远科技有限公司目录一、注意事项二、产品简介三、基本说明1、控制面板功能及其意义2、阀门通电后显示屏显示3、出厂默认参数4、按键的意义5、参数查询、设定及修改6、手动功能7、显示8、保护功能9、信号输出及控制功能10、安装管路及水路试运行11、通电试运行12、控制电路功能及连接A、信号输出端口B、互锁C、泄压端口D、远程控制端口四、常见故障及其排除方法五、组件及零部件编号六、保修说明一、注意事项★确保产品安装后的正常使用，请在使用前让专业的安装或维修人员确认。
★安装时如有任何管道工程及任何电器工作都必须由专业人员完成。
★本阀门安装时需要远离强磁场，如果有变频器和水泵，变频器和水泵的连接线需要用屏蔽电缆连接。
★严禁将该阀用于不安全的或者不明水质的地方。
★过滤个过程的参数应根据工作条件的变化和出水的要求及时修正。
★使用过程中，应周期性的检测水质，以确保系统的正常运行。
★切勿将阀门靠近热源或高湿度、有腐蚀性、强磁场、强震动等环境中，亦不能将其直接暴露于室外。
★严禁将排水管和其他接头作为支撑提升或搬运系统。
★请在水温为5~50℃、水压为0.15~0.6MPa范围内使用本产品，在此范围外使用本产品所引发的故障或事故不在本公司责任及保修之列。
★如果进水压力大于0.6MPa，需在进水口端安装减压阀；进水压力低于0.15MPa 时，应在进水端加装增压泵。
★切勿让儿童接触或玩耍，不小心碰到操作键可能导致程序发生变化。
★本产品附带的电源线及电源适配器损坏时，必须更换本公司出厂的电源线及电源适配器。
二、产品概述1、主要用途适用范围主要用于水处理系统中进行过滤过程的智能化控制。
适用于家用过滤系统、泳池过滤设备、反渗透预处理系统中的过滤器等。
2、产品特点2.1 结构简单密封可靠采用高平面度、耐腐蚀的端面密封片开闭，密封可靠；集运行、反洗、正洗等全过程功能于一体。
SWD-QBH 数字化全闭环电梯调速装置使用维护说明书 - 维多自控
SWD－ＱＢＨ数字化全闭环电梯调速装置使用维护说明书沈阳维多自控技术有限公司数字化全闭环电梯速装置使用维护说明书数字化全闭环电梯调速装置是一种以单片计算机为核心的交流电梯调速控制器（以下简称调速器），全部采用数字化方法实现从速度给定、速度反馈、速度调节到可控硅触发等控制功能，可适用于速度为1.75米／秒以下的交流调速电梯，为了便于用户使用维护本装置，现将该调速器的基本原理及使用方法详述如下。
用户在使用调速器之前应认真阅读此说明书。
一、调速器的原理及功能调速器的原理框图如图一所示。
光电脉冲调速系统的主回路电动部分采用可控硅反并联三相交流调压控制，制动部分采用单相半控桥实现能耗制动控制，是一种典型的交流调压调速控制系统，简称ＡＣＶＶ。
速度指令是在计算机内部存储的一组经过量化后的理想速度曲线值。
当系统收到起动或制动信号后，计算机通过执行相应的控制程序将速度指令曲线调出。
用户在进行系统调试时，可以通过主控板上的ＤＩＰ开关选择不同的起、制动曲线以获得最佳乘座舒适感，满足电梯起、制动过程中平均加、减速度指标。
速度反馈值是计算机通过安装在电机轴端的光电码盘和光电开关产生的脉冲信号经过计算获得的。
计算机将速度指令值和速度反馈值进行比较，对其差值进行比例、积分和微分（ＰＩＤ）调节运算，再将运算的结果转换成代表可控硅触发角的数字量，通过数字触发通道触发电动或制动可控硅，控制施加在电机上的电压，从而达到调节电机速度、使其跟踪理想速度指令曲线的目的。
在系统调试过程中，ＰＩＤ运算参数可以通过主控板上ＤＩＰ开关进行选择。
在电梯的制动过程中，计算机通过光电码盘的脉冲信号可获得电梯实际位置的反馈信息，经过位置到速度的变换，产生按位置原则的制动速度指令曲线，再通过速度的闭环调节，控制电梯的速度均匀减至零时，正好到达平层位置，实现直接停靠。
调速器的控制功能主要包括如下几个方面：１、能够产生可由用户选择的理想速度指令曲线（内部），该曲线为抛物线和直线的组合。
数字方向·流量控制阀 D-DF (R) G说明书
3-1K数字阀控制系统数字方向·流量控制阀 D-DF (R) GDigital directional & flow control valves液压图形符号Ｄ-ＤＦＧ-３１-０６-２Ｃ-ＥＸ-１３０-１５７-（＊）-２１1 数字方向・流量控制阀2 尺寸规格标称3 阀芯型号（中立位置） 2：全部端口关闭4 弹簧设置方式 C：弹簧中心型5 最大控制流量 参照［规格］6 最大阶跃数100： ±100阶跃（5相电机） 7设计编号1数字方向・流量控制阀 D-DFG：无压力补偿阀D-DFRG：有溢流型压力补偿阀（适用于尺寸规格标称03，04） 2 方向控制位置数 2：中立及1位置 3：中立及2位置 3 负载敏感端口0：无端口 5：升降回路用（适用于尺寸规格标称04，06） 1：有端口 7：出口节流回路用（适用于尺寸规格标称04，06） 4 尺寸规格标称 参照［规格］5 阀芯型号（中立位置） 2：全部端口关闭6 弹簧设置方式 C：弹簧中心型7 EX：外部先导工作型（内置减压阀） 8 最大控制流量 参照［规格］ 9 最大阶跃数63 ：±63或±126阶跃（2相电机）※ 157：±157阶跃（5相电机） 10 阀芯详细分类 无符号：标准阀芯 1～：选配阀芯 11 设计编号20：D-DF（R）G-03，D-DFG-1021：D-DF（R）G-04，D-DFG-064Ｄ-ＤＦＧ-０１-２Ｃ-３０-１００-２０1257361471129310856型号※ 旧称4相电机（电机无变更。
）ＬＶＢＰＴＡＹＸＶＢＡＬＰＴＸＹＰＴＢＡD-DFG-01D-DFG-03～10D-DFRG-03/043-2 K 数字阀控制系统规格特性曲线图（20mm2/s时）（代表性示例）阀阶跃位置－流量特性（P→A/B差压约0.7 Mpa时）D-DFG-01D-DF (R) G-31-03D-DF (R) G-31-04D-DFG-31-06D-DFG-31-10D-DFGD-DFRG响应性能机差Y端口(泄油)允许压力过滤器(公称过滤粒度)2.510.712.710.812.818.245―最大控制流量的±3 %以下最大控制流量的0.1 %以下双向±157(P→A及P→B)(5相电机)2000 pps最大控制流量的2 %以下双向± 63(P→A及P→B)(2相电机)※1双向±126(P→A及P→B)(2相电机)※12～21(阀内置的减压阀设定为3 MPa。
D 1FH比例方向控制阀门说明书
( ) ( ) ΔPactual =
(5)
Qactual
2 Bar; (Q in LPM)
Qrated
[or]
= (75)
Qactual
2 PSI; (Q in GPM)
Qrated
A
D_1FH.p65, dd
A53
Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA
QA=QB QA>QB7) E21 B41
Spool Type
Code B
D31 LPM (GPM)
–
D41 LPM (GPM)
–
D81/D91 LPM (GPM)
–
D E22 B42
F
7) 2:1 Ratio: Reduced Flow Rate on Port B, Rated Flow Rate on Port A
G
C
Zero
U
I
Command
MIN
MAX
Signal E
0...±10V 0...±20mA
D
PID
Differential
Features
• Standard DIN/ISO/CETOP/NFPA interfaces. • Integrated valve electronics. • Spool position feedback. • High frequency response. • Spring centered main stage spool. • LED functional diagnostic indicator. • Wide selecton of spool options, and flow capacity. • 2:1 ratio spool options.
比例阀使用说明
全数字双闭环比例换向阀控制器使用说明书双闭环控制一、概述电路采用32bit高速CPU设计，具有结构简单可靠，参数长时间不会漂移，看门狗设计。
具有模拟量和数字量外部接口设计。
一块控制板可以方便控制比例换向阀，大大简化了常规设计。
二、功能特点1、集成双闭环设计，比例换向阀阀芯位置闭环控制\外部给定反馈闭环控制2、放大器和控制器合二为一，精简设备，减少维护量降低故障率3、具有使用模拟量接口4-20mA（或者0-20mA）反馈、4-20mA（或者0-20mA）（给定与主电路隔离）4、具有数字量接口设计，MODEBUSRS485RTU、CANBUS接口5、可以多个设备进行组网控制，适合多点集中控制6、外部给定反馈闭环控制PID参数调节通过3个电位器调整7、两路阀芯电磁铁控制具有输出过流保护8、看门狗设计，能够及时复位异常工况三、参数1、供电：DC15~30VDC @ 2A2、尺寸123（mm）X160（mm）3、调节精度±1%4、适用范围：华德比例换向阀6通径或10通径带阀芯位置反馈装置进行液压缸、液压缸伸缩位置定位控制，马达行走机构定位控制，液压升降机构定位控制，液压紧紧力装置控制、液压马达行走速度控制等5、工作温度：-30~60摄氏度6、湿度：7、震动：四、典型应用执行机构可以是液压缸，液压马达等执行部件，可以对控制对象进行精准控制五、接线说明六、调整方法此步骤为出厂已经调试好，一般用户无需调整，如果参数确实差异很大，请谨慎操作1、按照接线方法接好线，并认真检查正确后，将控制板上的保险丝去掉，控制板上电后，用万用表的交流档测量COM与L 和COM与R的电压应相同大约在2.3VAC，如果差异大（>0.1VAC）就需要松开位置传感器上的螺丝，将位置传感器的位置通过两个限位螺丝移动，直到测量COM与L 和COM与R的电压应相同为止。
这个步骤一般用户只做检查即可，已经出厂调整过。
如果确实差异很大就必须进行调整。
WKDP32G-8U-_-_A型滑动盒3通道 2位方向控制阀门说明书
-Screw-in cartridge valve -For cavity AU/C1030-All external parts with zinc-nickel plating according to DIN EN ISO 19598-Fits common cavity according to ISO and NFPA -Reliable switching, even after long dwell times -Low head loss-Optional with manual override-Installation in threaded port body type GAU-12-The slip-on coil can be rotated, and it can be replaced without opening the hydraulic envelope -High pressure wet-armature solenoids-Various plug-connector systems and voltages are availableDirectional valve 3-way/2-positionQ max = 40 l/min, p max = 350 barswitching solenoid, direct acting, spool typeType series: WKDP32G-8U-_-_A…operating environments. The slip-on coils can be replaced without opening the hydraulic envelope and can be positioned at any angle through 360°. These valves are primarily used in mobile and industrial applications as pilot valves for controlling the travel direction of actuators such as hydraulic motors and cylinders. For self-assembly, please refer to the secti-on related data sheets.DescriptionThe 3-way/2-position solenoid operated spool val-ves, series WKDP32G…, are NG 8, direct acting, pres-sure balanced screw-in valves with a 7/8-14 UNF mounting thread. They are designed on the proven sliding-spool principle. The straightforward design delivers an outstanding price/performance ratio. All external parts of the screw-in valves are zinc-nickel plated, and are thus suitable for use in the harshestSymbolTechnical dataNOTE!The switching time can be strongly de-pendent on flow rate, pressure, oil viscosity and the dwell time under pressure. In practice, the switching time may th-erefore deviate from the specified value range.Performance graphsmeasured with oil viscosity 33.0 mm²/s (cSt), coil at steady-state temperature and 10 % undervoltage p = f (Q) Performance limitΔp = f (Q) Pressure drop-flow rate characteristic400-PG-0737p [bar (psi)]0050 (700)100 (1400)150 (2100)200 (2900)250 (3600)300 (4300)350 (5000)Q [l/min (gpm)]40203010(10)(5)(7.5)(2.5)1)2)3)1) 2 → 1 solenoid de-energized 2) 2 → 3 solenoid energized 3) 3 → 2 solenoid energized400-PG-073602 (30)4 (60)6 (85)8 (120)10 (140)Q [l/min (gpm)]402030100p [bar (psi)]∆(10)(5)(7.5)(2.5)Dimensions and sectional viewOhne Handnotbetaetigung "O"without manual override "O"Mit Handnotbetaetigung "P"with manual override "P"Mit Handnotbetaetigung schraubbar "S"with screw-in manual oberride "S"s$NOTE!1) When fitting the screw-in cartridge valve, use the specified tightening torque. The value can be found in the chapter "Technical data". ATTENTION!Only qualified personnel with mechanical skills may carry out any maintenance work. Generally, the only work that should ever be undertaken is to check, and possibly replace, the seals. When changing seals, oil or grease the new seals thoroughly before fitting them.NOTE!The seals are not available individual-ly. The seal kit order number can befound in the chapter "Technical data". Installation informationRelated data sheets****************************© 2023 by Bucher Hydraulics AG Frutigen, 3714 Frutigen, SwitzerlandAll rights reserved.Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense. The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to continual improvement, we reserve the right to amend the product specifications contained in this catalogue.Ordering codeN =V=W =K =8=A … Q =Z … R =1 … 9=…=D =G =J =JR =U =UR=(blank)=Q =D =32G =P =U =O =P =S =。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
使用说明书
双闭环控制
1
一、 概述
电路采用 32bit 高速 CPU 设计，具有结构简单可靠，参数长时间不会漂移，看门狗 设计。具有模拟量和数字量外部接口设计。一块控制板可以方便控制比例换向阀，大大 简化了常规设计。
二、 功能特点
1、 集成双闭环设计，比例换向阀阀芯位置闭环控制\外部给定反馈闭环控制 2、 放大器和控制器合二为一，精简设备，减少维护量降低故障率 3、 具有使用模拟量接口 4-20mA（或者 0-20mA）反馈、4-20mA（或者 0-20mA）（给
2、 第 1 步做好后，将保险丝恢复，上电后测量下面图中的位置，按照图中的说明进行调整 操作。
4
3、 外部闭环 PID 参数调节 当接线正确，第 1 步和第 2 步骤都做好后，进行外部的控制，调节控制板上的三个一起 的蓝色电位器，P 表示比例，I 表示积分，D 表示微分。可以适当调整这三个电位器达 到最佳控制，应避免调节过大产生震荡。
四、 典型应用
执行机构可以是液压缸，液压马达等执行部件，可以对控制对象进行精准控制
五、 接线说明
2
3
六、 调整方法
此步骤为出厂已经调试好，一般用户无需调整，如果参数确实差异很大，请谨慎操作 1、 按照接线方法接好线，并认真检查正确后，将控制板上的保险丝去掉，控制板上电后，
用万用表的交流档测量 COM 与 L 和 COM 与 R 的电压应相同大约在 2.3VAC，如果差 异大（>0.1VAC）就需要松开位置传感器上的螺丝，将位置传感器的位置通过两个限位 螺丝移动，直到测量 COM 与 L 和 COM 与 R 的电压应相同为止。这个步骤一般用户只 做检查即可，已经出厂调整过。如果确实差异很大就必须进行调整。
1、 供电：DC15~30VDC @ 2A 2、 尺寸 123（mm）X160（mm） 3、 调节精度±1% 4、 适用范围：华德比例换向阀 6 通径或 10 通径带阀芯位置反馈装置进行液压缸、液
压缸伸缩位置定位控制，马达行走机构定位控制，液压升降机构定位控制，液压紧 紧力装置控制、液压马达行走速度控制等 5、 工作温度：-30~60 摄氏度 6、 湿度： 7、 震动：
定与主电路隔离） 4、 具有数字量接口设计，MODEBUSRS485RTU、CANBUS 接口 5、 可以多个设备进行组网控制，适合多点集中控制 6、 外部给定反馈闭环控制 PID 参数调节通过 3 个电位器调整 7、 两路阀芯电磁铁控制具有输出过流保护 8、 看门狗设计，能够及时复位异常工况
三、 参数
5
6
七、故障排除说明
序号 故障现象
故障原因
பைடு நூலகம்
排除方法
1
不按照预期的方式调节，总 比例换向阀发位置 从新接线
是到极端调节
传感器接线不正确
2
不按照预期的方式调节，总 两个比例换向阀电 从新接线
是到极端调节
磁阀线圈电缆没有
接对位置
3
比例换向阀阀不动作
保险丝断掉
更换保险丝 2A
4
调节不正确
5
调节震荡
6
调节迟缓，跟不上
比例换向阀位置移 动调整电位器位置 变动 PID 参数过大 PID 参数过小
从新调整
从新调节，减小 PID 参数 从新调节，减小 PID 参数
7