汽车模具英语

汽车冲压模具英语词汇

Die / Tool= 模具

Prog. Die=progressive die 级进模Ball bearing guide posts and bushings=球形滚珠导柱和轴套

Casting die=铸造模Cage=套Part=钣件Rigidity=强度Die material=制模材料Thin=薄

Tool design=模具设计Strip design=料条设计Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口”

Tool design approval=模具设计审核

Tool design modification/revision=模具设计更改

Tool parts design (detail) = 模具钣件设计（详细）Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引

FMC Make=保丽龙制作Construction method=结构方法

modification= 更改

Check & measure=检查& 测试

Machining= 机器加工

Large machining=在大型机器上加工上下模架（铣、车等）

Small machining=在小型机器上加工模块等Lower die trim inserts=下模切刃块

Lower trim inserts retainer=下模切刃块承盘Assemble inserts=组立镶块

Punch stripping plates=冲头压料板

Assembly=组立Trim punch backing plates=切刃冲头背板NC Machining=NC雕刻加工Stripper window inserts=料条窗户镶块

Fitting=研磨组立Spotting=合模Die tryout=试模Cushing stroke=缓冲行程

Dowel pin=定位销Guide lift pin=导引升降销

Assemble gas spring=安装氮气缸Stamp parts=冲钣件

Adjustment=调试Run off parts=冲钣件

Lower trim steels=下刃块Hit parts=冲钣件

Section=冲头断面Lifters=提升器

Trim punch=切刃冲头Coil=卷材

jack screw hole=起重[千斤顶]螺旋孔Guide block=导引块

Die set, lower plate=下模架Guide the coil through the tool=导引卷材Die set, upper plate=上模架layout inspection=全尺寸检验

Die inspection & approval=模具检查和审核Stretch carriers=拉伸运送装置

delivery=发货Punch stripping plates=冲头压料板Rejected=拒收Trim punch backing plates=切刃冲头背板Scrapped=报废Stripper window inserts=料条窗户镶块Rework=返工Heel plates=背托

stop block=停止块Prepare for delivery=准备发货

Hydro form 液压成形Key=键

Shear=剪切For locating retainer blocks=承盘键

Sensor=传感器For holding buttons or pilots=冲母座或导销

键

Stretch web=拉伸网For fixed heel or positive stop=镶根键Layout the parts=设计钣件Construction method=结构方法

Preceding into the design=继续设计Manual Surface Grinder=手动平面磨床Guide the coil through the tool=导引卷材Spotting red=合模用丹红

Checking aid /checking gage=检具Layout ink=试模用蓝墨水

Jig=夹具Masking tape=黄色不透明胶带(遮蔽胶带) Fixture=夹具Pliers=尖嘴钳，老虎钳

Ball bearing guide posts and bushings=

球形滚珠轴套

Cresent wrench=可调扳手

Guide post=导柱Bushings=导套Pump pipe=泵管

Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”CMM=三次元测量仪Symmetric=对称的

The axis of symmetry=对称轴Technical=技术上的Diagonal=对角线

Heeled die sets, internally heel form & trim sections=带箱根的模架，成形与切刃冲头带导引One two three block=一二三模块Adjustable parallels=可调平行块Stop block=阻止块

Granite Table=花岗岩平台Backing Plate=背板

Plotter= .描绘器, 图形显示器, 绘图器, 坐标自记器, 标图员Shoulder Bolt=肩头螺丝(Stripper bolt)

Belt Sander=带磨机Keeper Block=行程块Metal Cutting Band Saw=立式带锯床Corner Guide Block=导块Blanchard Grinder=大型平面磨床Dowel pin=定位销