室内温湿度传感器H7012B
湿度与温度传感器产品说明书
• Measuring range from 5 to 95 %HR and from 0 to 50 °C (1) or from -20 to +80 °C (2)• 0-10 V output, active, power supply24 Vac/Vdc (3-4 wires) or 4-20 mAoutput, passive loop, power supply from 16 to 30 Vdc (2 wires)• Housing with simplified mounting system• ABS V0 housing IP65(2) or IP20(1), with orwithout display • Alternating display of humidity and temperature • “¼ turn” system mounting with wall-mount plateFeatures of housingPart numberPower supply / Output A : Active 24 Vac/Vdc – 0-10 V P : Passive – 16/30 Vdc - 4-20 mA Display O : With display N : Without displayType of probe S : Ambient A : Duct D : Remote ES : StandardExample: TH 110-ANSHumidity and temperature transmitter TH 110, 0-10 V active, without display, ambient model.Caution: the TH 110 – POES model (passive with display) is not availableConfigurable outputs1 or2 analogue outputs(1)Ambient model / (2) Duct, remote and standard model.Ambient modelDuct modelProbe cable length (remote models only)( ): 2 m 05M: 5 m 10M: 10 mStandard modelTechnical specificationsConnectionsInside the front housing 1. Active switch (S1)2. Inactive switch3. LCC-S software connection4. Output terminal block5. Power supply terminal block6.Cable glandSimplified calibrationElectronic board and measuring element connected to the front side of the sensor, which allows toconfigure and calibrate your device without causing any damage.12Removable front face Fixed back housingGeneral features*Can be configured by switch.**All the accuracy indicated in this technical datasheet were stated in laboratory conditions, and can be guaranteed for measurements carried out in the same conditions, or carried out with calibration compensation.Measuring range Analogue output*654316354(standard model)Electrical connections as per NFC15-100 standardsThis connection must be made by a qualified and trained technician.IRH Vdc IT Vdc 1 2 hilos - +- +IRH Vdc IT Vdc IRH VdcIT Vdc IRH VdcIT Vdc symbol:F T _E N – T H 110 – 06/01/23 – N o n -c o n t r a c t u a ld o c u me n t – W e r e s e r v e t h e r i g h t t o m o d if y t h e c h a r a c t e r i s t i c s o f o u r p r o d u c t s w i t h o u t p r i o r n o t i c e .Only the accessories supplied with the device must be used.T o configure the transmitter , it must not be energized. Then, you can make the settings required, with the DIP switches (as shown on the drawing below).When the transmitter is configured, you can power it up.Please follow carefully the combinations beside with the DIP switch. If the combination is wrongly done, the following message will appear on the display of the transmitter “CONF ERROR”. In that case, you will have to unplug the transmitter , place the DIP switches correctly, and then power the transmitter up.1234Off OnActive switchUnit settingOutput setting On-off switch1234Active switch (S1)Please refer to the user manual of the LCC-S software to make the configuration.Set the DIP switches as shown beside. Connect the cable of the LCC-S to the connection of the transmitter .PC configurationSettings and use of the transmitterIt is possible to set the measuring ranges and the unit of the instrument either by switch and/or via software.Configurationis correctly installed. Ambient model does not have any mounting plate. 4 fixing holes are present inside the back Configuration via LCC-S software (option)It is possible to configure intermediate ranges, an offset...Example: for a 0-100 °C transmitter, minimum delta is 20 °C.The instrument can be configured from 0 to +20 °C or from -10 to +10 °C. In order to compensate a possible drift of the sensor, it is possible to add an offset to the displayed value by the TH 110 transmitter: it shows 48% RH, a standard instrument shows 45% RH. It is then possible, via the software, to integrate an offset of -3 to the displayed value by the TH 110 instrument.The configuration of the parameters can be done either with the DIP switch or via software (you can not combine both solutions).WarrantyInstruments have 1-year guarantee for any manufacturing defect.Maintenance:• Avoid any aggressive solvent.• Protect the transmitter and its probes from any cleaning product containing formalin, that may be used for cleaning rooms or ducts.Precautions for use: always use the device in accordancewith its intended use and within parameters described in the technical features in order not to compromise the protection ensured by the device.。
楼宇自控系统HVAC产品目录简介
可用于通风与空调装置上驱动截 面积大至从 3m2 至 6m2 的风阀， N20 系列为 20Nm 的风门执行器， 可 提 供 开 关， 浮 点 和 模 拟 控 制， N34 系列为 34Nm 的风门执行器， 可提供开关，浮点和模拟控制。
弹簧复位风门执行器。可用于通风 与空调装置上驱动截面积大至从 1m2 至 4m2 的风阀，可提供开关， 浮点和模拟控制。
楼宇自控系统 HVAC 产品目录简介
为您营造 舒适、节能、温馨的 工作方面占世界 领先地位的多元化跨国集团。在全球，其业务涉 及：航空产品和服务，楼宇、家庭和工业控制技 术、汽车产品、涡轮增压器、以及特殊材料。霍 尼韦尔公司总部位于美国新泽西州莫里斯镇，在 全球将近 100 个国家开展业务，拥有 120,000 名 员工。霍尼韦尔是构成道琼斯工业指数的 30 支 股票之一，也是标准普尔 500 家指数的股票之 一。霍尼韦尔公司名列“财富 100 强”，2006 年 全球销售收入达到 310 亿美元。
◆ VC6013/VC4013 风机盘管电动阀
◆ TB6980/TB7980 比例温控制器
用 于 XE70、XE99、DT70 系 列 风 机盘管控制系统，亦兼用于热水和 冷水。提供多种 Kv 值，功耗小， 可拆卸，无水锤。二通阀流向任意。 无进出口规定，静压力为 20Bar。 新型产品带保护帽，对阀门提供物 理保护并可用作手动开关。
应 用 于 加 热， 通 风 和 空 调 系 统 阀 门 的 调 节 控 制， 内 带 一 个 选 择 正 反作用的插头，提供 20mm 的行 程， 提 供 模 拟 输 出 0~10Vdc 或 2-10Vdc 的调节控制。
◆ ML7425 电动阀门执行 ( 弹簧复位）
◆ N05/N10 风门执行器
Honeywell_传感器_技术参数 2
目录：水系统传感器 (2)水流开关WFS-1001-H (2)液位开关MAC-3-5M (2)水管式压差传感器P7620C (3)水管式压力传感器P7620A (4)流量变送器8550+2517 (5)VF20T浸入式温度传感器 (5)风系统传感器 (7)DPS系列气流压差开关 (7)DPTM系列压差变送器 (7)风管式温度传感器LF20 (8)风管式温度传感器LF20-C (9)室外温度传感器T7416A1022 (9)室内温度传感器T7412A1000 (9)室内温度传感器CTR21 (10)风管式温湿度传感器H7050B1018 (10)风管式温湿度变送器H7050B1117 (11)室内温湿度变送器H7030A1000 (12)室内温湿度传感变送器H7012B1023 (12)室内温湿度传感器CTR21-H (13)风管式温湿度传感器H7015B1020 (14)室外温湿度传感变送器H7508A1042 (14)CDS2000 系列二氧化碳传感器 (15)C7110C1001(替换已停产的AQS51) 系列二氧化碳传感器 (15)AQS71-KAM(替换已停产的AQS51-KAM) 系列二氧化碳传感器 (16)GD250W3E 系列一氧化碳传感器 (17)C7110A1005系列房间空气质量传感器 (17)L4064K1006B 高温断路开关，手动复位 (18)T6950A1000 低温短路开关，手动复位 (18)数字化挂墙模块T7560 温度传感器 (19)数字化挂墙模块T7460 温度传感器 (19)水系统传感器水流开关 WFS-1001-H应用∙ WFS 水流开关具有SPDT 输出，性能优异，高精度可靠性，可安装在水管和对铜无腐蚀性液体中，当液体流量达到整定速率时，可不到整定点，其一个回路关闭，另一个回路打开，典型应用于连锁作用或断流保护的场所。
∙ WFS 系列开关仅用0℃以上液体介质，它亦可于高盐或氯气的液体，但是非易燃介质。
温湿度传感器（型号：WHT20B）使用说明书
温湿度传感器（型号：WHT20B）使用说明书版本号：1.0实施日期：2023-02-01郑州炜盛电子科技有限公司Zhengzhou Winsen Electronic Technology Co.,Ltd声明本说明书版权属郑州炜盛电子科技有限公司（以下称本公司）所有，未经书面许可，本说明书任何部分不得复制、翻译、存储于数据库或检索系统内，也不可以电子、翻拍、录音等任何手段进行传播。
感谢您使用本公司的系列产品。
为使您更好地使用本公司产品，减少因使用不当造成的产品故障，使用前请务必仔细阅读本说明书并按照所建议的使用方法进行使用。
如果您没有依照本说明书使用或擅自去除、拆解、更换传感器内部组件，本公司不承担由此造成的任何损失。
您所购买产品的颜色、款式及尺寸以实物为准。
本公司秉承科技进步的理念，不断致力于产品改进和技术创新。
因此，本公司保留任何产品改进而不预先通知的权力。
使用本说明书时，请确认其属于有效版本。
同时，本公司鼓励使用者根据其使用情况，探讨本产品更优化的使用方法。
请妥善保管本说明书，以便在您日后需要时能及时查阅并获得帮助。
郑州炜盛电子科技有限公司WHT20B温湿度传感器产品描述WHT20B温湿度传感器嵌入了适于回流焊的双列扁平无引脚SMD封装，温度和湿度信号可以在不同的引脚读出，底面3.0×3.0mm，高度1.0mm。
传感器输出经过标定的数字信号，标准I2C格式。
WHT20B温湿度传感器，包含一个全新设计的ASIC专用芯片内置晶体管Vbe温度特性，实现高精度温度检测；同时包含一个电容湿度芯片，其中湿敏材料吸湿后介电常数变化实现环境湿度检测。
并结合最新的集成电路信号处理技术而成的双芯片解决方案。
具有体积小、功耗低、可靠性高、兼容性好等优点。
产品特点⏹高精度，±3.0%RH和±0.5℃⏹宽电源电压范围，从2.0V到5.5V⏹采用SMD封装，适于回流焊⏹响应迅速、抗干扰能力强⏹高湿条件下优异的长期稳定性应用场景家电领域：家电、湿度调节、暖通空调、除湿机、智能恒温器、房间监视器；工业领域：汽车、测试及检测设备、自动控制；其他领域：数据记录器、气象站、医疗及其他相关温湿度检测控制。
霍尼韦尔控制阀门
霍尼韦尔控制阀门V4043,V4044风机盘管电动阀(弹簧复位)VC6013,VC4013风机盘管电动阀V5011P二通螺纹线性阀门V5013P三通螺纹线性阀门V5211F高关断力二通螺纹线性阀门V5328A法兰型二通线性阀门V5088A高关断力法兰型二通线性阀门V5329A/V5050A.B法兰型三通线性阀门V5016A二通法兰线性阀门V5025A二通法兰线性阀门PN25V5049A.B法兰型二通线性阀门PN25/40V5050A.B法兰型三通线性阀门PN25/40V5832A/V5833A.C小线性调节、开关阀门霍尼韦尔驱动执行器ML7420A电动阀门执行器ML7421A.B电动阀门执行器ML7425A电动阀门执行器N05系列5Nm风门执行器N10系列10Nm风门执行器N20系列20Nm风门执行器N34系列34Nm风门执行器S10系列10Nm弹簧复位风门执行器S20系列20Nm弹簧复位风门执行器霍尼韦尔数字式DDC控制器XL20小型DDC控制器XL50小型DDC控制器XL100中型DDC控制器XL500中型DDC控制器霍尼韦尔温度控制器T6373..系列风机盘管恒温器T6573/T6575 XE88,XE99,XE100系列数字式风机盘管恒温器T7126 T-STAR系列大屏幕数字式风机盘管恒温器DT70系列数字式风机盘管恒温器T6390系列液晶数显风机盘管恒温器T6800系列两管制大屏幕液晶显示风机盘管温控器T6861系列四管制大屏幕液晶显示风机盘管温控器Q6371风机三速开关T675,T678,T4031,T6031低温毛细管恒温器T991A比例式温度控制器T775A,E,F远程电子温度控制器T7984系列电子温度控制器T9275A单回路温度控制器R7428多回路温湿度控制器L4064K风机高温断路报警器L480低温断路报警器L4029高温断路报警器霍尼韦尔湿度控制器H49A,B,X/H69A湿度控制器H775A-E电子远端湿度控制器霍尼韦尔水流量控制WFS-1001-H液体水流开关霍尼韦尔温湿度传感器T7460系列房间温度传感器VF20T浸入式温度传感器LF20风管式温度传感器AF20室外温度传感器T7416A室外温度传感器T7425A快速浸入式温度传感器LF24风管式平均温度传感器KTF20/DKF20锅炉用温度传感器SAF25太阳光传感器IPF1房间居住者探测器GD250一氧化碳传感器AQS51系列二氧化碳传感器AQS61系列二氧化碳传感器C7110A房间空气质量传感器H7050系列风管式温湿度传感器H7030系列房间型温湿度传感器霍尼韦尔压力传感器DPS系列气流压差开关DPT系列压差变送器SK/SKV风管式静压、压差变送器ML系列压力传感器P7620A系列压力传感器L404A-D.F/L604A.L.M.N压力控制器P906系列压差控制器242PC压力传感器霍尼韦尔水控制产品Kombi-2-plus平衡阀V4 Kombi-F平衡阀Kombi-3-plus自动压差平衡阀DPCV自动压差控制阀V4系列电动蝶阀霍尼韦尔其它产品V5431A.F三通旋转阀门PN6V5433A三通旋转阀门PN6Q5001阀门连杆M7284,M7294,M9184,M9194,IV调节马达M6410C/L M7410C电动小线性阀门执行器M7410E电动小线性阀门执行器M6061A,L旋转阀门执行器M6063A,L旋转阀门执行器M7061E旋转阀门执行器DA0206A/DA0201A 1.5Nm风门执行器M447C1004 0.5Nm弹簧复位风门执行器FS4-3J流量开关T7412/T7560/TF26,H房间温度传感器WPF20L/T7413A/PS21,31/L7087A浸入式温度传感器VF20A/WPF20A/PAL21/T7414A外绑式温度传感器T7411A/PL21/T7415A/C7068A/L7087A风管式温度传感器DAF20室外温度传感器C7085A风管式平均温度传感器H7015A风管式湿度传感器H7015B风管式温湿度传感器H7012A房间型湿度传感器H7012B房间型温湿度传感器C7600B.C固态湿度传感器一,温度控制器1,T6373 XE702,T6573/T6575 XE88,XE99,XE1003,T7126T-STAR4,DT70 T63905,T6800 T68616,Q63717,T675,T678,T4031,T6031 8,T991A9,T775A,T775E,T775F10,T798411,T9275A12,R742813,L4064K14,L48015,L4029二,湿度控制器1,H49A,H49B,H49X,H69A2,H775A-E三,控制阀门(小线性阀门与大线性阀门) 1,V4043,V40442,VC6013,VC40133,V5011P4.V5013P5,V5011N,V5011P ,V5011F.V5011G6,V5013N7,V52118,V5328A9,V5088A10,V5329A,V5050A,V5050B11,V5016A12,V5025A13,V5049A,B ,V5050A,B14,V5832A/V5833A,V5833C15,V5431A,V5431F16,V5433A四,驱动执行器及连杆1,Q50012,M7284,M7294,M9184,M9194,IV3,M6410C/LM7410C/E4,ML7420A5,ML7421A.B6,M6063A,L M6061A,L7,M7061E8,DA0206A/DA0201A 1.5NM9,N05, N10系列5NM,10NM10,N20,N34系列20NM,34NM11,M447C10040.5NM12,S10,S20系列10NM,20NM五,水流量控制1,FS4-3J2,WFS-1001-H六,温湿度传感器1,T7412/T7460/TF26,H2,VF20T/WPF20L/T7413A/PS21,31/L7087A3,VF20A/WPF20A/PAL21/T7414A4,LF20/T7411A/PA21/T7415A/C7068A/L7087A 5,AF20/DAF20/T7416A6,T7425A7,LF24,C7085A8,KTF20/DKF209,SAF2510,IPF111,GD25012,AQS51/AQS6113,C7110A14,H7015A湿度,H7015B风管温湿度传感器15,H7012A湿度,H7012B房间式温湿度传感器16,C7600B.C固态湿度传感器七,压力传感器1,DPS2,DPT3,SK/SKV4,ML5,L404A-D.F/L604A.L.M.N6,P906八,水控制产品1,KOMBI-2-PLUS平衡阀2,V4KOMBI-F平衡阀3,KOMBI-3-PLUS自动压差平衡阀4,DPCV自动压差控制阀5,V4系列电动蝶阀九,数字式DDC控制器1,XL20小型DDC控制器2,XL50小型DDC控制器3,XL500大型DDC控制器4,XFL521/522/523/524 输入/输出模块SYMSTARTER-CD310 SymmetrE 软件基本包SYM-DB2-5-EXP SymmetrE 软件数据库扩展包，250-500点SYM-DB5-10-EXP SymmetrE 软件数据库扩展包，500-1000点SYM-DB10-20-EXP SymmetrE 软件数据库扩展包，1000-2000点Q7055A1007 BNA-1C网络通讯器Q7055A1015 BNA-2CS网络通讯器XI582CH 手提操作器XL50-MMI-FP DDC（AI8，DI4，AO4，DO6）XL50-FP DDC（AI8，DI4，AO4，DO6）XL50-MMI-EP DDC（AI8，DI4，AO4，DO6）XL100C XL100 DDC控制器XCL8010A Excel 800 plant controllerXF821A 8 analog input module (Panel)XF822A 8 analog output module (Panel)XF823A 12 binary input module (Panel)XF824A 6 relay output module (Panel)XFL821A 8 analog input module (LON)XFL822A 8 analog output module (LON)XFL823A 12 binary input module (LON)XFL824A 6 relay output module (LON)XS821-22 底座XS823 底座XS824-25 底座XL50UMMIPCCBLON XL50 FREIPROGR.+XS50+XD50B-FCL99-XFR-2AC24-20 变压器R7428A1006 MLC多功能控制器TB7980A1006 温度控制器50014157-001 温度传感器T9275A1002 单回路温度控制器L4064K1006B 断路器CN7505A2001 PI型电动执行器CN7510A2001 PI型电动执行器CN7220A2007 PI型电动执行器CN7234A2008 PI型电动执行器CN6105A1001 电动执行器CN6110A1003 电动执行器CN6120A1002 电动执行器LF20 风管插入式温度传感器VF20T 水管型插入式温度传感器H7050B1018 风管插入式温湿度传感器H7030A1000 室内温湿度传感器T7460A1001 室内温度传感器 NTC 20WFS-1001-H 水流开关P7620A1020 水压力传感器UEC24014M262 Differential Pressure Switch DPS400B 压差开关DPS1000B 压差开关DPTM1000 压差传感器0-1000Pa, with display, 0-10VDPTM50 压差传感器 +/-50Pa, 4-20 Ma8550+2517 电磁流量计FFS-10A 水位开关T7460B1008V5011N1040 电动二通阀DN15（铜阀塞）V5011N1057 电动二通阀DN20V5011P1004 电动二通阀DN25V5011P1012 电动二通阀DN32V5011P1020 电动二通阀DN40V5011P1038 电动二通阀DN50V5211F1004 电动二通阀DN65（铜）V5211F1012 电动二通阀DN80（铜）V5088A1005 电动二通阀DN100V5088A1013 电动二通阀DN125V5088A1021 电动二通阀DN150ML7420A6033-E PI型电动执行器ML7421A1032-E PI型电动执行器ML7421B1023-E PI型电动执行器ML7425A3013-E PI型电动执行器V5011N2048 电动二通阀DN15（不锈钢阀塞）V5011N2055 电动二通蒸汽阀DN20V5011P2036 电动二通蒸汽阀DN25V5011P2002 电动二通蒸汽阀DN32V5011P2010 电动二通蒸汽阀DN40V5011P2028 电动二通蒸汽阀DN50V5211F2002 电动二通蒸汽阀DN65V5211F2010 电动二通蒸汽阀DN80V5013N1063 电动三通阀DN25V5013P1002 电动三通阀DN32V5013P1010 电动三通阀DN40V5013P1028 电动三通阀DN50V5329A2077 电动三通阀DN65V5329A2085 电动三通阀DN80V5050A2088 电动三通阀DN100V5050A2106 电动三通阀DN125V5050A2114 电动三通阀DN150VBN2CJ3P0X/M 电动二通阀DN25 VBN2DK3P0X/M 电动二通阀DN32VBN2EL3P0X/M 电动二通阀DN40VBN2FN3P0X/M 电动二通阀DN50VBN2GR3P0X/M 电动二通阀DN65VBN2HT3P0X/M 电动二通阀DN80VBF2J11S0X/M 电动二通阀DN100, CV 197VBF2K31S0X/M 电动二通阀DN125,CV 309VBF2L51S0X/M 电动二通阀DN150, CV 441V4ABFW16-100-012 电动蝶阀DN100V4ABFW16-125-012 电动蝶阀DN125V4ABFW16-150-012 电动蝶阀DN150V4ABFW16-200-012 电动蝶阀DN200V4ABFW16-250-012 电动蝶阀DN250V4ABFW16-300-012 电动蝶阀DN300V4ABFW16-350-012 电动蝶阀DN350V4ABFW16-100-112 电动蝶阀DN100,调节式V4ABFW16-125-112 电动蝶阀DN125,调节式V4ABFW16-150-112 电动蝶阀DN150,调节式V4ABFW16-200-112 电动蝶阀DN200,调节式V4ABFW16-250-112 电动蝶阀DN250,调节式V4ABFW16-300-112 电动蝶阀DN300,调节式V4ABFW16-350-112 电动蝶阀DN350,调节式OM-1 On-Off, 90Nm, 220V 50/60Hz, Hand-Wheel，(DN125-DN150)OM-2 On-Off, 90Nm, 220V 50/60Hz, Hand-Wheel，(DN125-DN150)OM-3 On-Off, 150Nm, 220V 50/60Hz, Hand-Wheel，(DN200)OM-4 On-Off, 400Nm, 220V 50/60Hz,Hand-Wheel,(DN250-DN300)OM-7 On-Off, 1000Nm, 220V 50/60Hz,Hand-Wheel,(DN350)OM-8 On-Off, 1500Nm, 220V 50/60Hz,Hand-Wheel,(DN400)OM-P1 On-Off, 3500Nm, 220V 50/60Hz,Hand-Wheel,(DN600)OM-P2 Modulating, 90Nm, 220V 50/60Hz,Hand-Wheel，(DN125-DN150)OM-P3 Modulating, 150Nm, 220V 50/60Hz,Hand-Wheel，(DN200)OM-P4 Modulating, 400Nm, 220V 50/60Hz,Hand-Wheel,(DN250-DN300)OM-P7 Modulating, 1000Nm, 220V 50/60Hz, Hand-Wheel,(DN350)OM-P8 Modulating, 1500Nm, 220V 50/60Hz, Hand-Wheel,(DN400)V5032Y0032 Kombi-2平衡阀,DN32,螺纹联接V5032Y0040 Kombi-2平衡阀,DN40,螺纹联接V5032Y0050 Kombi-2平衡阀,DN50,螺纹联接V5032Y0020 Kombi-2平衡阀,DN20,螺纹联接V5032Y0025 Kombi-2平衡阀,DN25,螺纹联接Q6371A1006 三速开关T6373AC1108 风机盘管温控器,Heat or cool,2-pipeT6373BC1130 风机盘管温控器,Heat and cool,2-pipeT6375B1153 风机盘管温控器,Heat or cool,4-pipeT6390A1001 数字式温控器,2-pipe Fancoil, cycle fanT6391A1001 数字式温控器,4-pipe Fancoil, cycle fanT6800H2WN 数字式温控器（横款）T6800V2WN 数字式温控器（竖款）T6861H2BB 数字式温控器（蓝色，横款）T6861V2BB 数字式温控器（蓝色，竖款）T6861H2GG 数字式温控器（绿色，横款）T6861V2GG 数字式温控器（绿色，竖款）VC6013AJC1000 电动二通阀DN20,BSPP/240v/Cable,SPATVC6013AP1000 电动二通阀DN25,BSPP/240v/Cable VC6013MJ6000 电动三通阀DN20,BSPT/240v/Cable VC4013AJ1000 电动二通阀DN20,BSPP/240v/Cable,SPSTV4043C1362B 电动二通阀DN20,弹簧复位型,BSPP/220v,50HzV4-BLC-GP16-G065 V4 Kombi-F静态平衡阀,DN65 V4-BLC-GP16-G080 V4 Kombi-F静态平衡阀,DN80 V4-BLC-GP16-G100 V4 Kombi-F静态平衡阀,DN100 V4-BLC-GP16-G125 V4 Kombi-F静态平衡阀,DN125 V4-BLC-GP16-G150 V4 Kombi-F静态平衡阀,DN150 V4-BLC-GP16-G200 V4 Kombi-F静态平衡阀,DN200 V4-BLC-GP16-G250 V4 Kombi-F静态平衡阀,DN250 V4-BLC-GP16-G300 V4 Kombi-F静态平衡阀,DN300 V4-BLC-GP16-G350 V4 Kombi-F静态平衡阀,DN350 V5328A1179-E 电动二通阀,DN65,for waterV5328A1187-E 电动二通阀,DN80,for waterV5088A1005-E 电动二通阀,DN100,for water V5088A1013-E 电动二通阀,DN125,for waterV5088A1021-E 电动二通阀,DN150,for waterV5328A2011-E 电动二通阀,DN65,for steamV5328A2029-E 电动二通阀,DN80,for steamV5088A2003-E 电动二通阀,DN100,for steamV5088A2011-E 电动二通阀,DN125,for steamV5088A2029-E 电动二通阀,DN150,for steamP906C2004 diff pressure controller（4-20ma）DPCV-40A 动态压差平衡阀,DN40,0.2~0.5bar DPCV-50A 动态压差平衡阀,DN50,0.2~0.5bar DPCV-65A 动态压差平衡阀,DN65,0.2~0.5bar DPCV-80A 动态压差平衡阀,DN80,0.2~0.5bar DPCV-100A 动态压差平衡阀,DN100,0.2~0.5bar DPCV-125A 动态压差平衡阀,DN125,0.2~0.5bar DPCV-150A 动态压差平衡阀,DN150,0.2~0.5bar DPCV-40B 动态压差平衡阀,DN40,0.6~0.9bar DPCV-50B 动态压差平衡阀,DN50,0.6~0.9bar DPCV-65B 动态压差平衡阀,DN65,0.6~0.9bar DPCV-80B 动态压差平衡阀,DN80,0.6~0.9bar DPCV-100B 动态压差平衡阀,DN100,0.6~0.9bar DPCV-125B 动态压差平衡阀,DN125,0.6~0.9bar DPCV-150B 动态压差平衡阀,DN150,0.。
Honewell 产品目录
产品目录一、温度控制器1 、T6373 XE70系列风机盘管恒愠器 (5)2 、T6573/T6575 XE88,XE99,XE100系列数字式风机盘管恒温器 (9)3 、T7126 T-STAR系列大屏幕数字式风机盘管恒温器 (16)4 、DT70 系列数字式风机盘管恒温器 (19)5 、XE80 系列数字式风机盘管恒温器 (23)6 、Q6371 三速风机开关 (25)7 、T675,T678,T4031,T6031低温毛细管恒温器 (27)8 、T991A比例式温度控制器 (30)9 、T775A,E,F远程电子温度控制器 (32)10、T7984系列电子温度控制器 (37)11、T9275A单回路温度控制器 (40)12、R7428多回路温湿度控制器 (42)13、L4064K风机高温断路报警器 (45)14、L480低温断路报警器 (46)15、L4029高温断路报警器 (48)二 、湿度控制器1 、H49A,B,X/H69A湿度控制器 (49)2 、H775A-E电子远端湿度控制器 (53)三 、控制阀门 (小线性阀门与大线性阀门）1 、V4043,V4044风机盘管电动阀 ( 弹簧复位 ) (58)2 、VC6013,VC4013风机盘管电动阀 (60)3 、V5011P二通螺纹线性阀门PN16 (65)4 、V5013P三通螺纹线性阀门PN16 (70)5 、V5011N,P,F,G二通螺纹线性阀门PN16 (75)6 、V5013N,P三通螺纹线性阀门PN16 (76)7 、V5211F高关断力二通螺纹线性阀门 PN16 (77)8 、V5328A法兰型二通线性阀门PN16 (78)9 、V5088A 高关断力法兰型二通线性阀门PN16 (79)10、V5329A/V5050A.B法兰型三通线性阀门PN16 (80)11、V5016A二通法兰线形阀门PN16 (81)12、V5025A二通法兰线形阀门PN25 (82)13 、V5049A.B法兰型二通线性阀门PN25/40 (83)14、V5050A.B法兰型三通线性阀门PN25/40 (84)15 、V5832A/V5833A.C小线形调节、开关阀门PN16 (85)16 、V5431A.F三通旋转阀门PN6 (87)17 、V5433A三通旋转阀门PN6 (88)18 、大线性阀与执行器匹配表 (89)19 、旋转阀与执行器匹配表 (93)20 、Cv值的计算 (94)四、 驱动执行器及连杆1 、Q5001阀门连杆 (98)2 、M7284,M7294,M9184,M9194,Ⅳ调节马达 (100)3 、M6410C/L M7410C电动小线性阀门执行器 (106)4 、M7410E电动小线性阀门执行器 (107)5 、ML7420A电动阀门执行器 (108)6 、ML7421A.B电动阀门执行器 (114)7 、M6061A,L旋转阀门执行器 (118)8 、M6063A,L旋转阀门执行器 (119)9、 M7061E旋转阀门执行器 (120)10、DA0206A/DA0201A1.5Nm风门执行器 (121)11、N05，N10系列5Nm，10Nm风门执行器 (122)12、N20，N34系列20Nm，34Nm风门执行器 (123)13、M447C1004 0.5Nm弹簧复位风门执行器 (124)14、S10，S20系列10Nm，20Nm弹簧复位风门执行器 (125)五、水流量控制1 、FS4-3J (126)2 、WFS-1001-H液体水流开关 (128)六、温湿度传感器1 、T7412/T7460/T7560/TF26,H房间温度传感器 (130)2 、VF20T/WPF20L/T7413A/PS21,31/L7087A浸入式温度传感器 (131)3 、VF20A/WPF20A/PAL21/T7414A外绑式温度传感器 (132)4 、LF20/T7411A/PL21/T7415A/C7068A/L7087A风管式温度传感器 (133)5 、AF20/DAF20/T7416A室外温度传感器 (134)6 、T7425A快速浸入式温度传感器 (135)7 、LF24，C7085A风管式平均温度传感器 (136)8 、KTF20/DKF20锅炉用温度传感器 (137)9 、SAF25太阳光传感器 (138)10 、IPF1房间居住者探测器 (139)11、GD250一氧化碳传感器 (140)12、AQS51/AQS61系列二氧化碳传感器 (141)13、C7110A房间空气质量传感器 (142)14、H7015A湿度、H7015B风管式温湿度传感器 (143)15、H7012A湿度、H7012B房间式温湿度传感器 (145)16、C7600B.C固态湿度传感器 (147)七、压力传感器1 、DPS系列气流压差开关 (149)2 、DPT系列压差变送器 (150)3 、SK/SKV风管式静压、压差变送器 (151)4 、ML系列压力传感器 (152)5 、L404A-D.F/L604A.L.M.N压力控制器 (154)6 、P906压差控制器 (157)八、水控制产品1 、Kombi-2-plus平衡阀 (159)2 、V4 Kombi-F平衡阀 (164)3 、Kombi-3-plus自动压差平衡阀 (170)4 、Kombi压差控制膜盒 (172)5 、DPCV 自动压差控制阀 (173)6 、V4系列电动蝶阀 (179)九、数字式DDC控制器1 、XL20小型控制器 (183)2 、XL50小型控制器 (187)十、HVAC产品应用图例1 、风机盘管控制（二管式、单一冷水盘管) (192)2 、风机盘管控制（二管式、冷/热水二用盘管） (194)3 、风机盘管控制（四管式 、冷/热水盘管独立） (198)4 、空气处理机组控制 （二管式、单一冷水盘管） (200)5 、空气处理机组控制（二管式、冷 /热水二用盘管） (202)6 、新风处理机组控制（二管式、单一冷水盘管） (205)7 、新风处理机组控制（二管式、冷/热水二用盘管） (207)8 、恒温恒湿DDC控制原理图 (209)9、 热交换器控制 (210)10、冷冻/热水压差旁路控制 (211)十一、工程实例部份产品项目应用清单 (212)T6373 XE70系列风机盘管恒温器概述· T 6373恒温器可应用于控制阀门，或者管风机中的阀门和风门。
Neosensor室内用温度传感器室内用湿度传感器室内用温湿度传感器
量范围大、稳定性高，可用于一般楼宇空调为主的各种室内应 用。
本资料不含2线式(4-20 mA 输出)型的Neosensor的规格。 请参阅以下的资料。
AI-7051C 规格使用说明书 Neosensor (2线式 4-20 mA 输出型) 室内用温度传感器 (TY7043D) 室内用湿度传感器 (HY7043D) 室内用温湿度传感器 (HTY7043D)
HY7043T6000-1
类型 Neosensor
电源 24 V DC/AC
Neosensor
24 V DC/AC
Neosensor
不要电源
Neosensor
不要电源
Neosensor
不要电源
高灵敏度 Neosensor 不要电源
Neosensor
24 V DC/AC
Neosensor
24 V DC/AC
进行检查。
对湿度检测，腐蚀性气体或有机溶剂等会引起输出漂移或引起故障。本产品(HY7043, HTY7043)在与通常的空 气不同的环境下使用的场合，请咨询本公司的销售人员。
2
型号
基础型号
HTY70 TY70 HY70
形状
4 5
种类 3
电源 湿度输出
T Z
0 1 6
温度输出
0 P K
固定 输出线
使用前请仔细阅读本使用说明书，并在规格范围内正确地使用本产品。 阅读后，请务必将使用说明书保管在可随时查阅的地方。
使用上的限制和注意事项
本产品用于普通的空调控制。请勿在有碍人身安全的情况下使用本产品。 另外，当用于洁净室、动物棚舍等对可靠性、控制精度有特别要求的用途时，请咨询本公司的销售人员。 对由于用户使用不当造成的后果，本公司概不负责。敬请谅解！
海康威视 HM70 手持湿度和温度计说明书
Order form Valid from August 2021Orderer Order no.HM70 Handheld Humidity and Temperature MeterHM70 PRICE Indicator type no indicator *Arechargeable with Euro AC-adapter Brechargeable with UK AC-adapter Crechargeable with US AC-adapter Drechargeable with AUS AC-adapter Erechargeable with all AC-adapters Frechargeable with JP AC-adapter Jalkaline batteries only KIndicator accessories no indicator accessories0MI70LINK software with RS232 cable (MI70LINK)1analog output-signal cable (27168ZZ)2MI70LINK with RS232 and analog output signal cables3MI70LINK software with USB cable (219687)4Probe type HMP75AHMP75B (chemical purge and sensor preheating)FHMP76BHMP76B (chemical purge and sensor preheating)CHMP77DHMP77B (chemical purge and sensor preheating)ECalibration at room temperature1Probe accessories no accessories Aprobe holder for HMP76/76B **BConnection cable no connection cable0to a transmitter connection cable to HMD/W60/70 series (HMA6070)1connection cable to HMP230 series / HMP228 (27159ZZ)2connection cable to 20/30 series transmitters (HMA2030)3connection cable to HMT330 and HMT120/130 (211339)4connection cable to HMW90 (219980)6Carrying case no carrying case Aweather proof carrying case for MI70 and probe (HMP75/77/77B) (MI70CASE3)Dweather proof carrying case for MI70 and long probe (HMP76/76B) (MI70CASE4)EManual No manual AMultilingual Quick Guide (EN, JA)****BSpanish User Manual ETOTAL* select item A, if only probe is ordered QTY** used in field calibration of duct 60/70 and 20/30 transmitters TOTAL VALUE*** aluminium case for HMP76 probe (long case)**** Comprehensive HM70 User Guide in English available at /HM70Selections in bold are included in the prices of the basic versions.Selections in italic are available at an extra price.Example of order code with typical settings:HM70B4F1A0D BEnd customer:Accessories:Order code:Connection cable to HMT330 and HMT120/130211339Connection cable to HMT310DRW216050Connection cable to HMD/W60/70 series HMA6070Connection cable to HMW90219980Weather proof carrying case for MI70 and short probe MI70CASE3Weather proof carrying case for MI70 and long probe MI70CASE4MI70LINK software with USB cable219687MI70LINK software with serial port cable MI70LINKAnalog output cable27168ZZProbe cable extension, 10 m213107SPRestricted。
楼控(EBI)
楼宇自控系统
设备几材料名称 EBI软件 计算机 C-BUS通讯器 XL500现场控制器 通讯连接模XFL521/522/523端接模块 XFL524端接模块 XFL522超弛模块 XFL524超弛模块 风管温度传感器 室外温湿度传感器 风压差开关 风门执行器 电动调节阀 电动调节阀 电动调节阀 液位开关 液位传感器 温度传感器 水压力传感器 附件 水流量传感器 水流开关 电动开关碟阀 电动开关碟阀 电动开关碟阀 电动开关碟阀 电动调节阀（旁通阀） 电流变送器 电压变送器 有功功率变送器 功率因数变送器 频率变送器 控制箱 规格型号 EBI（3500点） IBM P4 2.4G Q7055A1015 XCL5010 XSL511 XFL521 XFL522 XFL523 XFL524 XFL513 XFL514 XFLR522 XFLR524 LF20 H7012B DPS400 ML7284 V5011（DN40） V5011（DN50） V5011（DN80） KEY UQZ VF20T ML016BS 3685901 MODEI2517+8510 PS4-3J V4-ABFL-EPN16-150-03 V4-ABFL-EPN16-200-03 V4-ABFL-EPN16-250-03 V4-ABFL-EPN16-300-03 V4-ABFL-EPN16-200-04 M100-AA3 M100-VA3 M100-WA5 M100-PA3 M100-FA1 Honeywell /美国 Honeywell /美国 Honeywell /美国 SIGNET/英国 ITT美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 品牌及产地 Honeywell /澳大利亚 IBM/国产 Honeywell /德国 Honeywell /德国 Honeywell /德国 Honeywell /德国 Honeywell /德国 Honeywell /德国 Honeywell /德国 Honeywell /德国 Honeywell /德国 Honeywell /德国 Honeywell /德国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 Honeywell /美国 单位 套 台 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个 个
智能温湿度传感器文档说明书
GENERAL USE AND APPLICATIONSUse your smartphone, tablet or computer to remotely monitor ambient temperature and humidity levels that affect your home second home, office or rental property.* The 6 foot detachable dry probe measures temperature of air outside through a window, or even in your refrigerator or freezer.* Text & e-mail alerts can signify power outages to help you protect property or prevent frozen pipes.*MONITORING OPTIONS•Home, second home, office or rental property•Indoor or outdoor temperature and humidity •Basement, garage, attic and utility room •Refrigerators, freezers and dry food storage•Plants, gardens and greenhouses•Outdoor pets, farms and livestock•Books, photos and musical instruments•Computers, servers and electronics•Wine storage and humidors•Fireplace mantelPACKAGE CONTENTSHARDWARE:1. Wireless Ambient Temperature and HumidityMonitor with mounting bracket (TX60U-IT)2. *Wet or Dry Temp. Probe included in select packages.See (B) in the FEATURES AND MEASUREMENTSsection for more details.3. Mounting hardware (screws and drywall anchors) PRINTED MATERIALS:5. Printed Product Overview Guide (this document)IMPORTANT: Product set up and activationinstructions are online: 6. IMPORTANT: Activation Key Card required forset up and activation. Do not throw away.•Two fresh AAA, IEC LR03, 1.5V Alkaline batteries•Two-sided tape as needed•Browser with high speed Internet•Network router•Existing La Crosse Alerts Internet Gateway with mounting bracket, AC adapter and LAN cable (sold separately)FEATURES AND MEASUREMENTS (Diagram 1)(A) Wireless Ambient Temperature & Humidity Monitor:•LCD displays ambient air temp. & humidity (CH1)•LCD displays probe temperature (CH2)•Transmits collected data to Internet Gatewaywithin a 200 Ft. wireless range.•Weather resistant case (not water proof)Note: The case with LCD cannot get wet andmay be affected by high humidity conditions.•Wall hanging or free standing(B) **Optional Temp. Probe on 6 Ft. Detachable Cable:•Wet & Dry temperature probes are sold separately.Check your retailer for availability. Attach a probe atany time with no need to reset sensor.•**Attach a dry temperature probe to the main sensorcase to monitor DRY environments such as air or drysoil. MODEL #: D000.101.BG•**Or attach a Wet probe for measuring wet or humidconditions such as a pool, aquarium or terrarium:MODEL #: D000.102.BG or D000.103.BGHOW IT WORKS•The wireless sensor transmits temperature and humiditymeasurements to the Internet Gateway within a 200 Ft.(60.96m) wireless range.*•The Internet Gateway (sold separately) connects to yourexisting network router and uses your high-speed Internetconnection to upload collected measurements to your ownaccount at .*•Once the sensor and gateway are activated on youraccount, you can monitor sensor(s) online from a(1) *(2)(B)**Optional externalin select packages.smartphone, tablet or computer, and set up custom e-mail/text alerts*.•Add up to 5 sensors (sold separately) per Internet gateway (sold separately) to monitor additional areas.1. Begin set up near your existing network router and a computer with high-speed Internet access.2. Unpack package contents and insert temp. probe (if it’s included) into the TX60U-IT case (see diagram 1).1. Locate the Activation Key Card in the package for setupinstructions and the Activation Key . The Activation Key is necessary to activate your sensor with Internet Gateway (sold separately). Keep your Activation Card for reference. 2. Visit with your Activation KeyCard to create your account and activate the product.ACTIVATION INFORMATION:THE INCLUDED ACTIVATION KEY is good for1 year of ENHANCED SERVICE with early warning text & e-mail alerts, plus 4 more years of BASIC SERVICE for standard remote monitoring.Lost your Activation Key Card?Contact Customer Support:/support/alerts Phone: (608) 785-7920Once the sensor is activated and building a measurement log, you can download the data as a comma separated values (CSV) file. You must use an application such as Microsoft Excel® or Google Docs® that supports comma separated values (CSV) formatted files to view the table data.• Select a location protected from water and otherprecipitation. The case is water resistant, not water proof. • Place the sensor in a dry, shaded area. Avoid locations with direct sun, to prevent inaccurate readings.• Fog and mist will not harm the sensor but direct precipitation must be avoided.• Note: Exposing the sensor case to extreme humidity may temporarily disrupt data. The sensor case reads humidity, but should not be submerged in water.• Select a location within range of the Internet gateway (see “IMPORTANT SETUP & OPERATION NOTES”).• IMPORTANT: Before permanently mounting…Test sensor in the desired mounting location for at least 1 hour to confirm good reception. Confirm consistent readings on your account at before permanentlymounting. Move the sensor closer to the Internet Gateway if the signal is lost or not received. • Mount the sensor after the activation process (see “SETUP AND ACTIVATION”). MOUNT TO WALL WITH SCREWS1. Remove the mounting bracket2. Place bracket over the desired location.3. Mark mounting surface with a pencil through the 2 holes of the bracket.4. Screw bracket onto surface and tighten screws to bracket.5. Insert the sensor back into the bracket.FREE STANDINGAttach the mounting bracket to the bottom or top of the sensor and place it on any flat surface.PLACEMENT OF TEMPERATURE PROBE (Optional)• Confirm that the end of the probe cable is secured in the socket inside the sensor (See Diagram 1).• Insert the dry temp. probe on 6 Ft. cable into a refrigerator or freezer, or dry soil, etc. for a separate reading of air or soil temperature. The dry temp. probe is not for use in water. • **An optional wet probe should be used to measure wet environments (sold separately). Check your retailer for availability: MODEL #: D000.102.BG• Loosely coil and secure extra cord with a twist tie or secure with tape (not included).• The sensor has a wireless range of 200 feet (60.96 m). The 200 ft. range equates to open air with no obstructions, and that radio waves DO NOT curve around objects. Actualtransmission range will vary depending on what is in the path of the signal. Each obstruction (roof, walls, floors, ceilings, etc.) will effectively cut signal range in half.• Metal, stucco, and some types of glass can reduce signal range by as much as ¾ or more, compared to the ½ reduction typical of most obstructions. It is possible toreceive a signal through these materials, however maximum range will be reduced due to their tendency to absorb or reflect a much larger portion of the sensor’s signal.• The sensor measures and updates the temperature and humidity on the LCD every 6 seconds.Note : The new measurement is reported to your account at intervals that you select using your online account.1. Remove the battery cover by sliding the cover down.2. Observing the correct polarity install 2-AAA batteries. The batteries will fit tightly (to avoid start-up problems make sure they do not spring free).3. Do not mix old and new batteries.4. Do not mix alkaline, lithium, standard or rechargeable batteries.5. Replace the battery cover by sliding upwards and check that it is securely fitted.• Low battery icon appears on LCD when batteries are low. • You will receive an e-mail or mobile text message alert when the battery power of the sensor is low. Change the batteries immediately.Note: The LED light turns ON briefly after changing batteries. The LED light turns OFF when not needed to save battery power. The previously stored information in the temperature and humidity sensor will not be affected or cancelled while you change the batteries.• Avoid extreme temperatures, vibration and shock. • Clean the sensor with a soft, damp cloth. Do not use solvents or scouring agents.• Do not submerge the sensor case in water. • Do not kink the 6 ft. sensor cable.• Secure the 6 ft. cable to avoid tripping hazards.• Immediately remove all low powered batteries to avoid leakage and damage.• Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology® for repairs.Temperature range:-40°F to 140°F with 0.2°F resolution“OFL” displayed if outside this range. Humidity measuring range: 3% to 99% Transmission range:200 feet (60.96 m) in open spaceTemp. Probe 6 Ft. Cable: Channel 2:-40°F to 140°F with 0.2°F OPTIONAL resolution “OFL” displayed if outside this range, and displayed “nC” if probe is not connected.Sensor battery power 2 x AAA Alkaline, IEC LR03, 1.5V Internet gateway power: AC adapter (included) Battery life cycle:Approximately 24 monthsTX60U-IT size: 5.23" H x 0.76" W x 1.44" DLa Crosse Technology, Ltd provides a 1-year limited warrantyon this product against manufacturing defects in materials and workmanship.This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and serviceprocedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. Theoriginal dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center.La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remainingoriginal warranty, or ninety (90) days, whichever is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered by this warranty. If necessary repairs are not covered by this warranty, or if a product isexamined which is not in need or repair, you will be charged for the repairs or examination. The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground returnshipping charges to the owner of the product to a USA address only.Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specifiedexceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, ordeterioration of, any accessory or decorative surface; (4)damage resulting from failure to follow instructions contained in your owner’s manual; (5) damage resulting from theperformance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference.. This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances.LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUMELIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF CHILDREN’S REACH.This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do not allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information, please contact:La Crosse Technology, Ltd2817 Losey Blvd. S. La Crosse, WI 54601/support/alertsLost your Activation Key Card?Contact Customer Support:/support/alerts Phone: (608) 785-7920* Disclaimers: La Crosse Technology, LTD. (“La Crosse”) provides various alert and monitoring services to aid users. (1) Service providers may charge users for alert services. Standard messaging and data rates apply and will be billed to the customer’s wireless account. Customers may be unable to receive text messaging or data service in some areas due to unavailability of service. (2) La Crosse shall not be liable for accuracy, usefulness or availability of data transmitted via the service. Users are solely responsible for damages to persons or property by service use.All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or processed using electronic, mechanical or chemical procedures without written permission of the publisher.This handbook may contain mistakes and printing errors. The information in this handbook is regularly checked and corrections made in the next issue.We accept no liability for technical mistakes or printing errors, or their consequences. All trademarks and patents are acknowledged.5,978,738 6,076,044 6,597,990This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference.2) This device must accept any interference received,including interference that may cause undesired operation.。
SIGMA II 温湿度计说明书
Use an external fan for faster response and more accurate measurement. It is in combination with this fan that the maximum capability of measurement for temperature and humidity can be achieved.The fan inhales fresh air into the instrument and makes the response of sensor faster, resulting in the detection of accurate data. It is effective, par ticularly in warehouses which are excluded from the open air, laboratories where ventilation is poor or air tight small space.SIGMA II THERMOHYGROGRAPHSPECIFICATIONSCat. No.: No. 7211-00 (Quartz type)Measuring range: –10 to 50°C for temperature 0 to 100% for relative humidity Other specifications: same as 7210-00Cat. No.: No. 7215-00 (Spring-wound type)Model: NSII-SClock: Spring-wound typeDrum rotation: 1 day and 7 day changed by gear Weight: Approx. 3.5kgAccessories: 7 day chart for 1 year use (55 sheets/pad), chart holder, Test resultOther specifications: same as 7210-00 quartz typeCat. No.: No. 7210-00 (Quartz type)Model: NSII-QMeasuring range: –15 to 40°C for temperature 0 to 100% for relative humidity Clock: Quartz type:1 day, 7 day and 32 day by change-over switch Battery: "C" size battery x 2Battery life: 1 year for continuous use Sensors: Aged bimetallic strip for temperature Human hair bundle for humidity Accuracy: ±1°C for temperature (10 to 30°C)±3%RH for humidity (20 to 95%RH at 15 to 25°C) ±5%RH (other range)Chart graduation: 1°C for temperature 1% for RH Recording pens: Cartridge pens (violet)Dimensions: 336 (W) x 148 (D) x 295 (H) mm Weight: Approx. 3.1 kgAccessories: 7 day chart for 1 year use (55 sheets/pad), Test result "C" size battery x 2Exclusive ChartsOther AccessoriesThe charts for "SIGMA II" series can be interchangeably used with ''SIGMA'' series products except 32 day chart. The charts with mmHg scale is available.。
常用SENSOR安装手册
24 V
+
+
两芯1.0电源线
DDC 控制器
-
-
1.C7110C1001带CO2传感器、 CO2浓度LED指示。 2.C7110D1009带温度设定拨盘、温度传感器、 CO2传感器、 LED有人无人控制、旁路 按钮控制。 3.此墙装模块为墙面安装方式。 4.将墙装模块后座安装在离地面 1.3m以上高度的墙面上，用螺丝固定，注意安装时右侧 预留100mm宽度的空间。 5.按接线图完成接线，然后将面盖合上 (24Vac或24Vdc的电源另配 )
RVVP2X1.0
设备端
C7068A1007,C7068A1007-5m
设备端
接线安装详细
法兰接头 套筒接头
视角 A
平均温度传感器连接线通往 DDC
10-15mm
传感器
传感器
棒状支架
50mm
墙面孔槽
棒状支架
传感器
22mm 60mm 80mm
传感器 柔性支架
安装孔模板
接线图 安装说明 AI DDC 控制器 DDC 控制器 1.按照所附的安装模板开孔，安装法兰附件 ,传感器还要用支架固定。 2.传感器线与 380Vac/220Vac线最小距离为 150mm。 3.传感器与控制器的最大距离为 200m。 AI GND
24V
设备端
风管或风道
接线安装详细
垫圈
视角 A
开孔向风 直径6mm 转孔 直径7.3mm
夹子
开孔向风 安装孔 孔内穿 5.5mm螺丝
2/3 管直徑
LF20 温度传感器 通往DDC
管子隔离材料
温度传感器导线放在软管内
接线图 AI DDC 控制器 AI GND 安装说明 1.温度传感器与控制器的最长距离为 200m。 2.传感器线与 380Vac/220Vac线最小距离为 150mm。 DDC RVVP2X1.0 黄色 红色 设备端 设备端
HX80A系列湿度传感器与温度传感器产品说明书
H uEnvironmental/Process Air Transmitters RH and Temperature with Dew Point or Pressure Outputs U 316 SS HousingU ±1% RH AccuracyU ±0.5°C (1.0°F) Temperature AccuracyU H igh Temperature[120°C (248°F)]U R emovable StainlessSteel Sensor Cap U RS232 StandardU A djustable ¾ NPTFitting The HX80A Series is a family of humidity probes that offer a variety of measurement parameters with precision accuracy: relative humidity and temperature, with dew point or pressure. The probe is easily adaptable for most applications via a 3⁄4 NPT fitting that can beadjusted to any desired position, including high temperature and high pressure conditions. This remote type transmitter comes standard with a 1.8 m (6') cable and is ideally suited for many different applications such as environmental chambers, compressed air, and industrial applications. Models offer a stainless steel probe with a removable sinter stainless steel filter and RS232 (which allows for reading of data, scaling output, and for HX86A type units, changing the digital display and setting the alarms). All models have 3 outputs, with output 1 scaled for 0 to 100% RH, output 2 scaled for -20 to 120°C (-4 to 248°F), and output 3 determined by the model number. Output 3 for HX85A and HX86A is -60 to 40°C (-76 to 104°F) dew point, forHX85BA and HX86BA is 750 to 1100 mb, and for HX85PAand HX86PA is 0 to 200 psia. RH measurement range is 5 to 95% with an accuracy of ±1%. temperature accuracy is ±0.5°C (33°F).HX85A (probe only) models (HX85A, HX85BA, HX85PA) offer 0 to 10V signals on the outputs via a 1.8 m (6') cable. The HX86A models (HX86A, HX86BA,HX86PA) include a display box attached to the end of the cable from the probe, and offers a 2 line digital display, 2 alarms, three 4 to 20 mA output signals, and an RS232 serial output.SPECIFICATIONS RH Accuracy: ±1% RH RH Measurement Range: 5 to 95%Time Constant: <15 sec, air flow dependent (for 66.6% response)Temp Accuracy: ±0.5ºC (1.0°F)Temp Measurement Range: -20 to 120ºC (-4 to 248ºF) Pressure Rating: 317 kg (700 lb) (47.6 bar) max Serial Output: RS232C (bi-directional) to DTE device, 19.2 kilo baud, 8 bits data, 1 stop bit, no parity Power Requirements: 18 to 30 Vdcunregulated, 50 mA max HX85A shown smaller than actual size.HX86ASensor Dimensions: robe: 19 Dia. x 203 mm (3⁄4 x 8") Cable Length: 1.8 m (6')Filter: Sinter stainless steel (removable and cleanable)Probe Material: Stainless steelFitting: Adjustable ¾ NPTWeight: 0.9 kg (2 lb)Display Box (HX86A, HX86BA, HX86PA Only): Dimensions: 130 x 94 x 56 mm (5.1 x 3.7 x 2.2") Mounting Centers: 115 x 79 mm (4.52 x 3.11") Digital Display: LCD, 2-line Electrical Analog Outputs (HX85A, HX85BA, HX85PA Only):0 to 10 Vdc (x3) @ 10 mA max Electrical Outputs (HX86A, HX86BA, HX86PA Only): Analog Outputs: 4 to 20 mA (x3) into 500 Ω max Ordering Example: HX85A, RH/air temperature/dew point transmitter with 0 to 10 Vdc outputs, and PSR-24S, regulated power supply90 to 264 Vac input with 24 Vdc output.Alarm Relay (x2): Form A (SPST , NO) rated at 3 A/250 Vac Barometric Pressure (HX85BA, HX86BA Only): Range*: 750 to 1100 mb Accuracy: ±5 mb * Although the unit is scaled 750 to 1100 mb, the unit actual measurement range is 10 to 1100 mb and can be reprogrammed in the field if the range needs to be expanded. High Pressure (HX85PA, HX86PA Only): Range: 0 to 200 psia Accuracy: ±0.75 psi。
CT M702参数设置
CT M702参数设置
M702温湿度控制器是一种用来监测环境温湿度的仪器，常用于对室内温湿度进行控制、监测和管理。
M702控制器具有多种参数，以满足不同的环境需要。
它具有内置的传感器，可以实时监测室内温湿度，内置定时器可以调整温湿度。
在调整M702参数时，首先要设置温湿度范围。
在设备上设置温湿度报警阈值，超出这一范围会发出警报。
另外，还可以设置温湿度控制反馈信号，表示温湿度合适时发出正向反馈信号，不合适时发出负向反馈信号，便于管理人员及时采取处理措施。
M702参数调节还可以设置温度控制方式、温湿度补偿等，并可以根据实际情况使用湿帘控制温湿度，可以有效降低环境温湿度，减少能耗，节约成本。
M702控制器的参数调节可以使环境温湿度符合要求，保护整个空间的安全和舒适程度，并提升性能。
通过仔细设置参数，可以让M702温湿度控制器为设施管理增添质量。
H7015A风管温湿度传感器
订货型号
H7015A1006 H7015B1004 H7015B1012 H7015B1020 H7015B1038
温
BALCO500 Ω at 23.3℃ NTC20K Ω at 25℃ 灵 敏 度： Pt100 0.385 Ω/K Pt1000 3.85 Ω/K BALCO 2 Ω/K 精 度： Pt100/Pt1000 △T/K=± (0.3+0.005*|t|) BALCO500 NIC ±0.4k at 23.3℃ ±0.2k at 25℃
Pt1000 BALCO500 20KΩNTC Pt100
应用
两种传感器均可用于 －排风和回风控制 －高限传感器，例如：蒸气湿度 －作为测量传感器，用于指示被测量的值。
技术规格
电 源： 24Vac，＋20...-30%；50／60Hz， 34Vdc、+20...-30% 电流消耗： 20mA@24V 工作温湿度范围： 0...50℃ 5-95%rh 贮藏温湿度范围： -35...+70℃ 5-95%rh 保护标准：端子合：IP54； 重 量： 度： 300g 标称值 Pt100 100 Ω at 0℃ Pt1000 1000 Ω at 0℃ 型 号 温度阻值特性
h7015b是湿度温度风管式传感器合二为一其中度传感器为电容式电容式温度传感器阻值特性为pt100pt1000balco500型20kntc技术规格h7015a湿度h7015b风管式温湿度传感器
H7015A湿度, H7015B风管式温湿度传感器
● H7015A是风管安装传感器，电容式相对湿度。 ● H7015B是湿度、温度风管式传感器合二为一， 其中湿度传感器为电容式， 电容式温度传感器阻 值特性为Pt100，Pt1000，BALCO500型20K ΩNTC
H7080B简要说明
简要说明：H7080B风管型温湿度传感器 H7080B2103 FLD DEVICES Temp & Hum, RH 3%, NTC20K详细介绍：H7080B风管型温湿度传感器H7080B2103 FLD DEVICES Temp & Hum, RH 3%, NTC20K1.0~10V，4.20mA 温度与湿度输出，或温度电阻输出；2.风道安装形式3.良好的线性度4.长期的稳定性5.高可靠性6.宽检测范围7. 灰尘与油污不影响传感8.安装简单技术规格相对湿度测量范围: 0~100%RH输出： 4~20mA:精度: 3%RH（@20ºC, 20~80%RH）全范围精度: 5%RH长期稳定性: ± 1%RH （每年）温度温度传感器: Pt1000 或NTC20K测量范围: 0~50ºC;0~100ºC;-10~60ºC输出 4~20mA 或0~10VDCNTC20K，PT1000;Ni1000精度± 0.2K @25ºC，NTC20K± 0.3K @25ºC，PT1000± 0.6K @25ºC，Ni1000With transimitter±0.5ºC 带变送（0~40ºC）长期稳定性 0.25C （每年）供电: 24 VAC/VDC ±10%电流负载 500 Ohm Max电流消耗 40mA Max工作温度 -30ºC~+70ºC储藏温度 -40ºC~+90ºC壳体材料 ABS 塑料，防火等级UL94/V1保护等级 IP54H7080B2103 FLD DEVICES Temp & Hum, RH 3%, NTC20KH7080B2105 FLD DEVICES Temp & Hum, RH 5%, NTC20KH7080B3102 FLD DEVICES Temp & Hum, RH 2%,Pt1000, 0°C~50°CH7080B3103 FLD DEVICES Temp & Hum,RH 3%, Pt1000, 0°C~50°CH7080B3105 FLD DEVICES Temp & Hum, Pt1000, RH 5%, 0°C~50°CH7080B3242 FLD DEVICES Temp& Hum, RH2%, 0~10V/4~20mA -10°C~40°C H7080B3243 FLD DEVICES Temp& Hum, RH3%, 0~10V/4~20mA -10°C~40°C H7080B3272 FLD DEVICES Temp& Hum, RH2%, 0~10V/4~20mA, 0°C~70°C H7080B3273 FLD DEVICES Temp& Hum, R H3%, 0~10V/4~20mA, 0°C~70°C。
温湿度传感器使用说明书
NO:S1*******使用说明书温湿度传感器目录1、产品介绍 (1)1.1概述 (1)1.2功能特点 (1)1.3外观尺寸 (1)2、性能参数 (2)3、使用方法 (4)3.1系统框架图 (4)3.2安装说明 (6)4、通信协议 (9)4.1通讯基本参数 (9)4.2数据帧格式定义 (9)4.3通讯基本参数 (11)4.4通讯协议示例以及解释 (12)5、常见问题及解决方法 (14)6、保养维护 (15)7、运输存储 (16)7.1运输要求 (16)7.2存储要求 (16)8、订货服务 (17)8.1订货方法 (17)8.2客户服务 (17)1产品介绍1.1概述本(系列)产品可在线监测环境温度和湿度信息，广泛用于开关柜仪表室、断路器室、电缆室等处的环境温湿度在线监测。
采用进口工业级微处理器芯片、进口高精度温度传感器，确保产品高精度和可靠性。
1.2功能特点◆进口的测量单元，测量精准。
◆专用的485电路，通信稳定。
◆宽电压范围供电，安装方便。
1.3外观尺寸（单位：mm公差：±0.5）2性能参数3使用方法3.1系统框架图本产品也可以多个传感器组合在一条485总线使用，理论上一条总线可以接254个485传感器，另一端接入带有485接口的PLC 、通过485接口芯片连接单片机，或者使用USB转485即可与电脑连接，使用我公司提供的传感器配置工具进行配置和测试(在使用该配置软件时只能接一台设备)。
3.2安装说明3.2.1注意事项1、传感器应尽量垂直放置，保证安装墙面时，温湿度探头在传感器本体的下方(传感器本体上的字体为正方向)。
2、安装高度为人体坐高或主要测量的环境区域。
3、避免在易于传热且会直接造成与待测区域产生温差的地带安装，否则会造成温湿度测量不准确。
4、安装在环境稳定的区域,避免直接光照,远离窗口及空调、暖气等设备,避免直对窗口、房门。
5、尽量远离大功率干扰设备，以免造成测量不准确,如变频器/电机等。
温湿度传感器型号大全
温湿度传感器型号大全1. DHT11温湿度传感器•型号：DHT11•工作电压：3.3V-5V•测量范围：温度0-50°C，湿度20-90%RH•精度：温度±2°C，湿度±5%RH•特点：低成本，数字输出，单线串行通信2. DHT22温湿度传感器•型号：DHT22•工作电压：3.3V-5V•测量范围：温度-40-80°C，湿度0-100%RH•精度：温度±0.5°C，湿度±2%RH•特点：数字输出，较高精度，需要外部电阻3. AM2302温湿度传感器•型号：AM2302•工作电压：3.3V-5V•测量范围：温度-40-80°C，湿度0-100%RH•精度：温度±0.5°C，湿度±2%RH•特点：数字输出，与DHT22相同4. SHT11温湿度传感器•型号：SHT11•工作电压：2.4V-5.5V•测量范围：温度-40-123.8°C，湿度0-100%RH•精度：温度±0.5°C，湿度±3%RH•特点：数字输出，较低功耗5. SHT15温湿度传感器•型号：SHT15•工作电压：2.4V-5.5V•测量范围：温度-40-123.8°C，湿度0-100%RH•精度：温度±0.3°C，湿度±2%RH•特点：数字输出，较高精度，带有可选的I2C接口6. HTU21D温湿度传感器•型号：HTU21D•工作电压：3.3V-5V•测量范围：温度-40-125°C，湿度0-100%RH•精度：温度±0.3°C，湿度±2%RH•特点：数字输出，高精度，可通过I2C接口进行通信7. BME280温湿度传感器•型号：BME280•工作电压：1.71V-3.6V•测量范围：温度-40-85°C，湿度0-100%RH•精度：温度±0.5°C，湿度±3%RH•特点：数字输出，温湿度压力三合一传感器，可通过I2C或SPI接口进行通信8. BME680温湿度传感器•型号：BME680•工作电压：1.71V-3.6V•测量范围：温度-40-85°C，湿度0-100%RH•精度：温度±0.5°C，湿度±3%RH•特点：数字输出，温湿度压力气体四合一传感器，可通过I2C或SPI 接口进行通信9. HDC2080温湿度传感器•型号：HDC2080•工作电压：1.62V-3.6V•测量范围：温度-40-125°C，湿度0-100%RH•精度：温度±0.2°C，湿度±2%RH•特点：数字输出，高精度，可通过I2C接口进行通信以上是一些常见的温湿度传感器型号及其主要参数介绍。