拓展-0603红黄双色led贴片灯珠规格书,参数

160～180℃ 100 seconds Max. 260℃ Max. 5 seconds Max. Refer to Temperature-profile
Temperature Soldering time
260℃ Max.
3 second Max. (one time only)
• After reflow soldering rapid cooling should be avoided
ＳＭＤ ＬＥＤ
1.4 [0.063]
0.6 [0.028]
[R0R.00.0177]5
1
1.6 [0.063]
2
0.10 [0.004]
3
4
1.2 [0.043] 3°
0.30 [0.012]
1.5 [0.067]
0.20 [0.008]
2
1
4
3
1.0 [0.028]
1
R2
3
Y4
RESIN: EPOXY
ATTENTION
OBSERVE PRECAUTIONS
ELECTROSTATIC SENSITIVE DEVICES
核准：
业务： 段小姐
工程：
日期： ２０１２－０８－０５
客户名称：
合 格 不合格
原因：
联系人：
客户确认：
ＡＤＤ：深圳市宝安区西乡宝田一路拓展工业区 ＴＥＬ：０７５５－２９６３２５４１ ＦＡＸ：０７５５－６１５２８６２５ ｈｔｔｐ：／／ｗｗｗ．ｔｚｌｅｄ．ｎｅｔ
If=20mA If=20mA If=20mA If=20mA If=20mA If=10mA Vr=5V
R λpeak
Ｙ
R △λ
Ｙ
Ｒ Vf
Ｙ
R λd
Ｙ
R Iv
Ｙ
2 θ1/2
Ir
NOTE: (Tolerance: Iv ±10% , λd ±2nm , Vf ±0.05V ) IFP Conditions : Pulse Width≦10msec. and Duty ≦1/10.
Derating
Ambient Temperature vs. Maximum Forward Current
Forward Current (mA) Forward Current vs. Dominate wavelength (Ta=25° C)
Dominate wavelength (nm)
Parameter
Test Condition Symbol
Wavelength at peak emission Spectral Half bandwidth Forward voltage Dominant wavelength Luminous intensity Viewing angle at 50% Iv Reverse current
Relative Intensity
Forward Current (mA)
Relative Intensity
Relative Intensity
Wavelength[nm] Relative Intensity vs. Ambient Temperature
Forward Voltage VF(V)
Pd
Forward current
If
Reverse voltage
Vr
Operating temperature range
Top
Storage temperature range
Tstg
Pulse Forward Current
Ifp
Electrostatic Discharge
ESD
Electro-optical characteristics at Ta=25℃
Reliability
(1)TEST Байду номын сангаасTEMS AND RESULTS
ＳＭＤ ＬＥＤ
Environmental Sequence
Type
Test Item
Resistance to Soldering Heat(Reflow Soldering)
Temperature Cycle
Thermal Shock
75cm
Note
2 times 100 cycle
100 cycle 1000 hrs 1000 hrs 1000 hrs 100 cycle 1000 hrs 500 hrs 1000 hrs 3 times
Number of Damaged
0/22 0/100
0/100 0/100 0/100 0/100 0/100 0/100 0/100 0/100 0/10
Temperature-profile (Surface of circuit board)
Use the following conditions shown in the figure.
RECOMMEND PAD DESIGN (Units: mm)
TEMPERATURE C M5ACX /SEC.
ＳＭＤ ＬＥＤ
Reflow profile
Soldering condition
• Recommended soldering conditions
Reflow Soldering
Hand Soldering
Pre-heat Pre-heat time Peak temperature Soldering time Condition
Value
Ｒ
Ｙ
50
50
25
5
-30 ~+80
-40~+100
100
1000(HBM)
Unit
mW mA V ℃ ℃ mA V
Value Unit
Min. Typ. Max.
--
--
--
nm
--
-
--
--
--
35
30
--
nm
--
2.0
2.5
V
3.0
--
3.4
620
--
630
nm
585
--
590
nm
80
Forward Current (mA)
Ambient Temperature Ta(° C)
Ambient Temperature Ta(° C)
Diagram characteristics of radiation
0
10
20
30
Forward Current (mA)
ＡＤＤ：深圳市宝安区西乡宝田一路拓展工业区 ＴＥＬ：０７５５－２９６３２５４１ ＦＡＸ：０７５５－２９６３２５４５ Ｈｔｔｐ：／／ｗｗｗ．ｔｚｌｅｄ．ｎｅｔ
ＡＤＤ：深圳市宝安区西乡银田宏鹏辉工业园Ｂ栋 ＴＥＬ：０７５５－２９６３２５４１ ＦＡＸ：０７５５－２９６３２５４５ Ｈｔｔｐ：／／ｗｗｗ．ｔｚｌｅｄ．ｎｅｔ
ＳＭＤ ＬＥＤ
Absolute maximum ratings at Ta=25℃
Parameter
Symbol
Power dissipation (two circuit)
LED DICE
BONDING WIRE:Φ25um Au
PRINTED CIRCUIT BOARD: BT
ELECTRODE
NOTES:
1. All dimensions are in millimeters (inches); 2. Tolerances are ±0.1mm (0.004inch) unless otherwise noted.
Criteria for Judgement
Min.
Max.
_
U.S.L*)×1.1
_
U.S.L*)×2.0
L.S.L**)×0.7
_
U.S.L.: Upper Standard Level
L.S.L.: Lower Standard Level
ＡＤＤ：深圳市宝安区西乡宝田一路拓展工业区 ＴＥＬ：０７５５－２９６３２５４１ ＦＡＸ：０７５５－２９６３２５４５ Ｈｔｔｐ：／／ｗｗｗ．ｔｚｌｅｄ．ｎｅｔ
ＳＭＤ ＬＥＤ
深圳市拓展光电有限公司
ＳＨＥＮＺＨＥＮ ＴＵＯＺＨＡＮ ＯＰＴＯＥＬＥＣＴＲＯＮＩＣＳ ＣＯ．，ＬＴＤ
贴片型发光二极管规格书
产品型号 : 文件编号 : 版本编号 : 产品描述:
ＴＺ－０３ＲＹ３ＨＣ TZL-13-063RY V.03
■ ０６０３贴片型超高亮双色ＬＥＤ ■ 发光颜色: 红／黄 ■ 胶体颜色: 无色透明 ■ 半功率视角：140°
100
mcd
--
７０
90
mcd
--
140
--
Deg
--
--
10
µA
ＡＤＤ：深圳市宝安区西乡宝田一路拓展工业区 ＴＥＬ：０７５５－２９６３２５４１ ＦＡＸ：０７５５－２９６３２５４５ ｈｔｔｐ：／／ｗｗｗ．ｔｚｌｅｄ．ｎｅｔ
Typical optical characteristics curves
Soldering iron
1. When hand soldering, keep the temperature of the iron under 300℃, and at that temperature keep the time under 3 sec.
2. The hand soldering should be done only a time 3. The basic spec is ≤5 sec. when the temperature of 260℃, do not contact the resin when hand soldering
High Temperature Storage Temperature Humidity Storage
Low Temperature Storage Power On/off Cycle Test
IF=20mA
Life Test High Humidity Heat Life
Test Low Temperature Life Test
Rework
1. Customer must finish rework within 5 sec under 260℃ 2. The head of iron can not touch the resin 3. Twin-head type is preferred.
ＡＤＤ：深圳市宝安区西乡宝田一路拓展工业区 ＴＥＬ：０７５５－２９６３２５４１ ＦＡＸ：０７５５－２９６３２５４５ Ｈｔｔｐ：／／ｗｗｗ．ｔｚｌｅｄ．ｎｅｔ
Operation Sequence
(2)CRITERIA FOR JUDGING THE DAMAGE
Item
Forward Voltage Reverse Current Luminous Intensity
Symbol
VF IR IV
Test Conditions
IF=10mA VR=5V IF=10mA
Feature
◆ Viewing angle:140 deg ◆ The materials of the LED dice is InGaN ◆ 1.6mm×1.6mm×0.6mm SMT-LED ◆ RoHS compliant lead-free soldering compatible
Package Outline
Drop
Test Conditions
Tsld=260℃,10sec
-20℃ 30min ↑↓5min
80℃ 30min -20℃ 15min
↑↓ 80℃ 15min
Ta=80℃ Ta=60℃ RH=90% Ta=-30℃ On 2 hours
↑↓ Off 10min Ta=25℃ IF=20mA 60℃ RH=90% IF=20mA Ta=-20℃ IF=20mA
Spectral Distribution Relative Intensity vs. Wavelength (Ta=25° C)
Forward Voltage vs. Forward Current (Ta=25° C)
ＳＭＤ ＬＥＤ
Relative Intensity vs. Forward Current (Ta=25° C)
5C MAX/.SEC.
２．４
０．２
MAX.
260 230 200 170 140 110 80 50 20
REFLOW PROFILE 5 SEC. MAX.
100 SEC. MAX
90
180
TIME (SECONDS)
above 220℃ 30sec max
240
２．４ １．０
1. Reflow soldering should not be done more than two times 2. When soldering ,do not put stress on the LEDs during heating