UCS 刀片服务器基本配置手册v1.0
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
UCS 刀片服务器基本
配置手册
V1.0
liuxyn@
2011.8.25
目录
0 UCS测试前准备工作 (1)
确认现场是否具备测试环境 (1)
电源环境 (1)
网络环境 (1)
设备拆箱所需工具 (1)
检查设备及相关配件 (1)
IP地址规划 (1)
1 UCS Manager 密码重置 (2)
2 UCS Manager删除配置 (6)
3 UCS Manger 初始化配置 (8)
4 UCS Manager web 管理 (9)
5 配置上联口(GLC-T)千兆上联到网络交换机 (12)
6配置Server Port (14)
7 配置管理IP 使用KVM,Vmedia (15)
8 配置Profile 模板 (15)
9 根据profile模板生成profile (15)
10 profile 关联刀片 (15)
11 安装操作系统 (15)
12 MDS 9124 系统恢复 (15)
13 MDS 9124 初始化配置 (16)
0 UCS测试前准备工作
确认现场是否具备测试环境
电源环境
5108 刀片机箱电源线为16A 插头,确认用户现场有16A插口的插线板
6120 功率350W左右
5108 功率最大功率2500W ,实际功耗取决于刀片多少
网络环境
6120 接5108刀片机箱最少需要1个万兆口互联
6120 上联到网络交换机千兆连接需要GLC-T模块连到网络交换机的千兆电口,或使用一对GLC-SX-MM模块+光纤跳线连到网络交换机的千兆SFP接口
6120 上联到SAN交换机需要4Gb的SFP模块和光纤跳线(如果刀片上没有配硬盘、或需要和存储互联做相关测试,需要有MDS9124或其他厂商的SAN交换机)
设备拆箱所需工具
美工刀、平口螺丝刀、十字螺丝刀、老虎钳
检查设备及相关配件
电源线(10A/16A)
模块(GLC-T或GLC-SX-MM),4Gb FC模块
网线、光纤跳线
IP地址规划
UCS6120 管理口IP地址
MDS9124 管理地址
存储设备管理地址
1
刀片KVM管理地址
ication OK
3038 Mar 30 2011 04:19:33 115468140 Jan 13 2011 03:03:00
plugin_file_is_excluded_from_exec_path: /boot/lib/libplugin_sysreg.so is excluded from linking plugin_file_is_excluded_from_exec_path: /boot/etc/ is excluded from linking
plugin_file_is_excluded_from_exec_path: /boot/etc/plugin_exclude.conf is excluded from linking plugin_file_is_excluded_from_exec_path: /boot/ is excluded from linking
plugin_file_is_excluded_from_exec_path: /boot/lib/ is excluded from linking
plugin_file_is_excluded_from_exec_path: /boot/lib/libplugin_sysreg.so.0.0.0 is excluded from linking
plugin_file_is_excluded_from_exec_path: /boot/lib/libplugin_sysreg.so.0 is excluded from linking plugin_file_is_excluded_from_exec_path: /boot/lib/libplugin_sysreg.so is excluded from linking plugin_file_is_excluded_from_exec_path: /boot/etc/ is excluded from linking
plugin_file_is_excluded_from_exec_path: /boot/etc/plugin_exclude.conf is excluded from linking 145680+1 records in
145680+1 records out
ethernet end-host mode on CA
FC end-host mode on CA
n_port virtualizer mode.
---------------------------------------------------------------
ln: `/isan/etc/sysmgr.d//fcfwd.conf': File exists
ethernet end-host mode
INIT: Switching to runlevel: 3
INIT: Sending processes the TERM signal
INIT: (boot)#
Exporting directories for NFS kernel daemon...done.
Starting NFS kernel daemon:rpc.nfsd.
rpc.mountddone.
Set name-type for VLAN subsystem. Should be visible in /proc/net/vlan/config
Added VLAN with VID == 4042 to IF -:muxif:-
---------------------
enabled fc feature
---------------------
2011 Mar 30 04:30:33 %$ VDC-1 %$ %KERN-2-SYSTEM_MSG: Starting kernel... - kernel Executing Port Power On Tests.......System is coming up ... Please wait ...
System is coming up ... Please wait ...
.System is coming up ... Please wait ...
.System is coming up ... Please wait ...
.System is coming up ... Please wait ...
.System is coming up ... Please wait ...
.System is coming up ... Please wait ...
Done
System is coming up ... Please wait ...
System is coming up ... Please wait ...
System is coming up ... Please wait ...
System is coming up ... Please wait ...
5