华三交换机命令大全审批稿

华三交换机命令大全 YKK standardization office【 YKK5AB- YKK08- YKK2C- YKK18】

一、

system

进入使能模式

password:

~~~~~~~~~~

[Quidway]super password

修改特权用户密码

[Quidway]sysname

交换机命名

[Quidway]interface ethernet 0/1

进入接口视图

[Quidway]interface vlan x

进入接口视图

[Quidway-Vlan-interfacex]ip address

[Quidway]ip route-static 静态＝网关

[Quidway]user-interface vty 0 4

[S3026-ui-vty0-4]authentication-mode password

[S3026-ui-vty0-4]set authentication-mode password simple 222

[S3026-ui-vty0-4]user privilege level 3

[Quidway-Ethernet0/1]duplex {half|full|auto}

配置端口双工工作状态

[Quidway-Ethernet0/1]speed {10|100|auto}

配置端口工作速率

[Quidway-Ethernet0/1]flow-control

配置端口流控

[Quidway-Ethernet0/1]mdi {across|auto|normal}

配置端口MDI/MDIX状态平接或扭接

[Quidway-Ethernet0/1]port link-type {trunk|access|hybrid} 接口工作模式

[Quidway-Ethernet0/1]shutdown

关闭/重起接口

[Quidway-Ethernet0/2]quit

退出视图

[Quidway]vlan 3

创建/删除一个VLAN/进入VLAN模式

[Quidway-vlan3]port ethernet 0/1 to ethernet 0/4

在当前VLAN增加/删除以太网接口

[Quidway-Ethernet0/2]port access vlan 3

将当前接口加入到指定VLAN

[Quidway-Ethernet0/2]port trunk permit vlan {ID|All} 设trunk允许的VLAN

[Quidway-Ethernet0/2]port trunk pvid vlan 3

设置trunk端口的PVID

[Quidway]monitor-port

指定和清除镜像端口

[Quidway]port mirror 指定和清除被镜像端口

[Quidway]port mirror int_list observing-port int_type int_num 指定镜像和被镜像

[Quidway]description string

指定VLAN描述字符

[Quidway]description

删除VLAN描述字符

[Quidway] vlan [vlan_id]

查看VLAN设置

[Quidway] {enable|disable}

开启/关闭生成树,默认关闭

[Quidway]stp priority 4096

设置交换机的优先级

[Quidway]stp root {primary|secondary}

设置交换机为根或根的备份

[Quidway-Ethernet0/1]stp cost 200

设置交换机端口的花费

[SwitchA-vlanx]isolate-user-vlan enable

设置主vlan

[SwitchA]Isolate-user-vlan secondary

设置主vlan包括的子vlan

[Quidway-Ethernet0/2]port hybrid pvid vlan

设置vlan的pvid

[Quidway-Ethernet0/2]port hybrid pvid

删除vlan的pvid

[Quidway-Ethernet0/2]port hybrid vlan vlan_id_list untagged 设置无标识的vlan

如果包的vlan id与PVId一致，则去掉vlan信息. 默认PVID=1。所以设置PVID为所属vlan id, 设置可以互通的vlan为untagged. 二、

sys 进入到系统视图

Enter system view, return to user view with Ctrl+Z. [Quidway]user-interface aux 0

[Quidway-ui-aux0]authentication-mode scheme

Notice: Telnet or SSH user must be added , otherwise operator cant login!

[Quidway-ui-aux0]qu

[Quidway]local-user huawei 增加用户名

New local user added.

[Quidway-luser-huawei]password simple huawei 配置密码,且密码不加密

[Quidway-luser-huawei]service-type telnet ssh level 3

类型为SSH和telnet,且用户登陆后权限为员权限

[Quidway-luser-huawei]qu

[Quidway]user-interface vty 0 4

[Quidway-ui-vty0-4]authentication-mode scheme