报警说明(斗山机床维修)

2005 HYD。PRESSURE DOWN ALARM 液压压力低报警
2006 HYD。PUMP MOTOR NOT RUN 液压马达没有运转
2007 SPINDLE STOP SIGNAL ALARM 主轴停止信号报警
2008 GEAR SHIFT CHECK SW。ALARM 换挡检测开关报警
第一主轴在急停状态（主轴在报警状态此报警 出现）
2003 The control circuit protectors are tipped out or fuse 空气开关跳脱或保险丝熔断 blown
2004 The hydraulic motor is overloaded The hydraulic pressure becomes below the set
错误的刀浩命令
2025
Keep relay setting to define the tool post model is not selected
控制刀塔型号的K参数没有设定
2026 The gear shift command(M41/M42/M43/M44)is not 换挡命令没有执行 accepted
2013 The Z-axis torque limiter s/w is tripped out. Trouble of z-axis torque limiter switch
Z轴扭力开关被绊住 Z轴扭力开关出错
2014 The B-axis torque limiter s/w is tripped out. Trouble of B-axis torque limiter switch The hydraulic oil of drain oil reservoir is
排屑机报警
DRUM FILTER CHIP CLT.LOW 2099 LEVEL
鼓式过滤器液面低
MUST BE RETUREND TO 2101 REF.POINT
必须返回原点
CYCLE START IN FIXTURE
2102 UNCLAMP
夹具放松时的循环启动
2103 MUST BE ATC 1 CYCLE
刀库同步故障 ATC 互锁报警
ATCMAGAZINE GUARD DOOR 2081 OPEN
ATC 刀库门开报警
ATC MAG.POT TOOL OUT
2082 SW.ALARM
刀库刀杯出来报警
2083 ATC MAINTENANCE STATUS
ATC维护状态
2084 ATHPCERSMETA-LUPCOSTMAPTEINOSNADTOIOONR OPEN APC安装站门开
立加报警说明
号码
英文注释
中文注释
2001 OP EMERGENCY PB OR LS OFF 急停开关被按下或轴向限位开关被碰到
2002 MAIN SPINDLE SERVO ALM
主轴伺服报警
2003 CIRCUIT PROTECT TRIP
电路保护故障
2004 HYD。PUMP MOTOR OVERLOAD 液压马达过载
中文注释
2064 AL
刀库等待刀杯到主轴侧/刀库侧报警
CHANGER ARM POS.CHECK 2065 ALARM
换刀臂位置检查报警
MUST BE COMMAND NEXT TOOL
2066 No.
必须指定下一个刀号
2068 ATC DOOR OPEN /CLOSE ALARM ATC门开/关报警
2037 M06 COMMAND ILLEGAL ALARM M06命令违法报警
MAG.MOVING ILLEGAL 2039 POS.ALARM
刀库移动错误位置报警
4-AXIS PRESSURE DOWN CHECK
2043 AL
第四轴压力低检测报警
FIXTURE CLAMP/UNCLAMP 2045 ALARM 2047 ATC DOOR OPEN 2048 OPERATORS SIDE DOOR OPEN
2017 overflowed. Trouble of float switch in the oil reservoir
B轴扭力开关被绊住 B轴扭力开关出错 液压蓄油池过溢报警 液压蓄油池过溢出错
2019 Keep relay setting to define the machine model is not selected
The x or z axis multi-limit switch is tripped out.
中文注释 急停按钮被按下或X，Z轴限位开关被压下
X，Z轴限位开关被压下
2002 The 1st spindle is in the Emergency status(It comes out when a 1st spindle alarm occurs)
SPDL STOP IN CUTTING MODE 2113 CMD 2114 RST COMMAND ALARM ON STL
切削模式主轴停 复位命令报警
车 床报警说明
序号
英文注释
The Emergency push button s/w is pressed. The X
2001 or Zaxis multi-limit s/w is tripped out.
2005 value.. Trouble of hydraulic pressure s/w
液压马达过载 油压压力在设定值以下 油压压力开关故障
2007 The zero-speed detection or the speed detection of 主轴马达零速检测器或速度检测器无检测 spindel motor is not detected.
2008 Fault of gear shift confirmation switch. 2009 The 2nd spindle Emergency status.(It comes out
when a 2nd spindle alarm occurs)
换挡开关出错 第2主轴在急停状态（2主轴在报警状态此报警 出现）
夹具夹紧放松报警 ATC门被打开 操作门被打开
润滑油位低或压力低 油温冷却器报警
冷却过滤器转换报警 冷却液压力低报警
刀具寿命结束报警 工件计数结束报警 主轴刀具夹紧/放松报警 刀库停止器进出报警 ATC 换刀位置报警 安全开关锁定报警
号码 WAIT.POT(MA英G文) S注P释D/MAG.SIDE
自动电源关准备中
2109 MACHINE LOCK ON STATUS
机床锁定中
2110 AUXILIARY FUNC.M,S,T,LOCK ON 辅助机能，即M，S，T锁定中
2111 APC SET-UP SW.UNPUSH
APC设定按扭没有按下
2112 MAN AБайду номын сангаасIS MOVING INTERLOCK 手动轴移动互锁
incorrectly.
2022 The spindle orientation command (m19) is not
主轴定位命令没有执行
accepted.
2023 The tool change command is not accepted.
换刀命令没有执行
2024 Incorrect tool No.is commanded.
2027 The spindle speed arrival signal is not detected.
2028
Spindle rotation command(M03/M04)is not accepted.
2029 The splash guard door is opened
冷却，润滑，或ATC马达过载 气压低报警
SPINDLE ORINETATION 2022 OVERTIME
主轴定位超时
M06 COMMAND OVERTIME 2023 ALARM 2024 T.CODE COMMAND ERROR
M06命令超时报警 T码命令错误
TOOL NO.SELECT KEEP/R NOT 2025 SET 2026 GEAR SHIFT OVERTIME ALARM 2027 SPDL SPEED ARRIVAL ALARM
LUB.LEVEL LOW OR PRESSURE 2050 DOWN 2051 OIL COOLING UNIT ALARM
COOLANT FILTER CHANGE 2052 ALARM 2053 COOLANT PRESSURE DOWN ALARM
TOOL LIFE MANAGE MENT END 2054 ALARM 2058 PARTS COUNT END ALARM 2060 SPINDLE TOOL CL/UNCL ALARM 2061 TMG STOPPER IN/OUT ALARM 2062 ASATFCECTHYASNWGIETRCHPOLSO.CAKLIANRGM 2063 ALARM
2032 SW)
外部速率保持
SPINDLE HEAD OIL PUMPING 2033 ALARM
主轴冷却油泵报警
CLNT W/TANK OR LEVEL SW
2034 ALARM
冷却液水位低报警
2035 TSC W/TANK MOTOR OVERLOAD TSC冷却马达过载
2036 TOOL SEARCH ILLEGAL ALARM 刀具搜索违法报警
关于机床种类的K参数没有设定
2020 The AC motor is overloaded.(coolant or lubrication 马达过载（冷却马达或润滑油马达）
pump motor)
2021 The Torque limit SKIP command is used
使用扭力限制跳过命令出错
2085 ERROR
热补偿错误
2087 GEAR SHIFT LOST
档位丢失
2088 TOOL BREAKAGE
刀具破损
2089 TOOL WEAR DETECT
刀具磨损检测
2090 PALLET UNCLAMP STATUS
工作台放松中
CHIP OR SCREW CONVEYOR 2094 ALARM
2010 Machine is in Not Ready status.
机床准备不足状态
2012 The X-axis torque limiter s/w is tripped out. Trouble of x-axis torque limiter switch
X轴扭力开关被绊住 X轴扭力开关出错
2009 MAGAZINE EMG。STATUS
刀库急停
MAIN POWER PHASE&ATC 2011 SWITCH ER
总电相序或ATC开关错误
SPINDLE TOOL UNCLAMP
2015 ALARM
主轴松刀报警
2017 SPINDLE HEAD OIL OVERFLOW 主轴冷却油过溢
CLT.&LUB&ATC.MOTOR 2020 OVERLOAD 2021 AIR PRESSURE DOWN ALARM
2074 ATC OVERTIME ALARM
ATC超时报警
ATC MAGAZINE ROT.OVERTIME
2075 ALARM
ATC 旋转超时报警
2077 4TH-AXIS CL/UNCL SW.ALARM 第四轴夹紧放松开关报警
TOOL MAG.SYNCHRO 2079 MALFUNCTION 2080 ATC INTERLOCK ALARM
刀具号选择保持开关没有设定 换挡超时报警 主轴速度到达报警
SPINDLE ROTATION 2028 MALFUNCTION 2029 APC DOOR OPEN
主轴旋转故障 APC门被打开
TOOL CHANGE MOTOR BRAKE
2030 RLS
换刀马达刹车释放
2031 AEXTCTEMRNAAINLTFEENEADNHCOELDST(AOTPUPSBINT ATC维护状态
ATC必须循环一次 K12.4=1
2104 SPINDLE TOOL No .ZERO
主轴刀号为0
2105 ATC OP MAUAL MODE
ATC手动模式
2106 APC OP MAUAL MODE
APC手动模式
2107 FEEDRATE OVERRIDE 0%
进给倍率选择开关为0
2108 AUTO POWER OFF READY