日本浅野ASANO真空成型机FLTP-9512-40
Sunnen Honing Guide
HONING GUIDEH e l p f u l T i p s F o r S o l v i n g B o r e S i z i n g & F i n i s h i n g P r o b l e msPRINTED IN U.S.A. 0410©COPYRIGHT SUNNEN ®PRODUCTS COMPANY 2004, ALL RIGHTS RESERVED X-SP-5061PSUNNEN PRODUCTS COMPANY7910 Manchester Ave., St. Louis, MO 63143 U.S.A.Phone: 314-781-2100 Fax: 314-781-2268U.S.A. Toll-Free Sales and Service –Automotive: 1-800-772-2878 • Industrial: 1-800-325-3670International Division Fax: 314-781-6128 e-mail:*****************GENERAL HONE CORP (A Sunnen Company)471 US 250 East, Ashland, OH 44805 U.S.A.Phone:419-289-3000 Fax: 419-281-0700U.S.A. Toll-Free Sales and Service: 1-800-837-1999SUNNEN PRODUCTS LIMITED No. 1 Centro, Maxted RoadHemel Hempstead, Herts HP2 7EF ENGLANDPhone:++ 44 1442 39 39 39 Fax: ++ 44 1442 39 12 12SUNNEN AG Fabrikstrasse 18586 Ennetaach-Erlen, SwitzerlandPhone:++ 41 71 649 33 33 Fax: ++ 41 71 649 34 34Sunnen®reserves the right to change or revise specifications and product design in connection with any feature of our products contained herein. Such changes do not entitle the buyer to corresponding changes,improvements, additions, or replacements for equipment, supplies or accessories previously sold. Information contained herein is considered to be accurate based on available information at the time of printing.Should any discrepancy of information arise,Sunnen recommends that user verify discrepancy with Sunnen before proceeding.SHANGHAI SUNNEN MECHANICAL CO., LTD.889 Kang Qiao East Road, PuDong Shanghai 201319, P.R. ChinaPhone:86 21 5 813 3322 Fax: 86 21 5 813 2299SUNNEN ITALIA S.R.L.Viale Stelvio 12/1520021 Ospiate di Bollate (MI) ItalyPhone:39 02 383 417 1 Fax: 39 02 383 417 50“SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN PRODUCTS COMPANY.”Standard Sunnen Tooling and Procedures will satisfy all ordinary honing requirements. If problems are encountered, they can usually be solved by following procedure suggested below. For detailed information on difficult or unusual honing problems contact your local Sunnen Field Engineer or Sunnen Customer Service Department in St. Louis, Missouri, USA.CONDITION TO BE CORRECTED STEP1STEP2STEP3STEP4STEP5STONE GLAZED*Sharpen A or J stone Increase cutting Increase stroking Use a softer stone Check oil to be STONE Stone surface looks with MAN-700pressure speed(one with a lower sure you are using NOT clean but cutting diamond dresser; use hardness number)Sunnen Industrial CUTTING grains are dulledLBN-700 dressing stick Honing Oil*on all other stones (Honing dial STONE LOADED*Clean stone with Increase stroking Use a softer stone Use a coarser grit Check oil to be needle moves Stone surface looks LBN-700 dressing pressure (one with a lower stone (one with a sure you are using too slowly)smeared and stickhardness number)lower grit number)Sunnen Industrial clogged with chipsHoning Oil*SLOW STOCK REMOVAL*Increase spindle speedIncrease cutting Check oil to be Use a softer stone Use a coarser grit (Honing dial needle moves too slowly)pressuresure you arc using (one with a Lower stone (one with a Sunnen Industrial hardness number)lower grit number)Honing Oil*POOR STONE LIFE* Decrease cutting Use faster spindle Use harder stone Use coarser grit stone Using Sunnen (Honing dial needle moves too fast)pressur e spe ed (higher hardness number) (lower g rit number) Industrial Honing Oil/Coolant*BELLMOUTH True stone and shoes Use softer stone If Bore is LONGERShorten STONE only If bellmouth persists with truing sleeve (OK with lower than 2/3 stone length:(or row of stones)shorten stones still If part is short or hardness number)slightly on both ends more but do not shorten unbalanced, shorten shoes any further stroke length If Bore is SHORTER Shorten STONES and CAUTION:than 2/3 stone length:SHOES equally to Overcorrection of1-1/2 times bore bellmouth will lead length to barrel conditionBARREL True stone and shoes Use finer grit stone Use longer stone or Use mandrel with CAUTION:with truing sleeve (one with higher grit shorten guide shoes longer stone and shoe Overcorrection ofnumber)on both ends barrel will leadto bellmouth conditionTAPER IN True stone and shoes Change stroke so tight Reverse work on If power stroking, make OPEN HOLE with truing sleeveend of bore is stroked mandrel more oftensure spindle and stroker over stone further are in alignment TAPER IN Shorten stone and True stone and shoes If hole has insufficient Provide sufficient Provide adequate oil BLIND HOLE shoes to about 3/4frequently with truing or no relief at bottom,relief at bottom of flow at bottom of hole shorten stone more sleeveuse hard tip stone holeto wash cutting out if taper persists OUT-OF-ROUNDMake sure honing Thoroughly true stone If thin wall part,If stone stops cutting If power stroking tool is recommended and shoes to exact decrease cutting at decreased pressure make sure spindle size for diameter to hole diameter pressure use stone with lower and stroker are in be honedhardness numberalignmentWAVINESS Use honing tool with sufficient stone length to bridge waviness (or Iands and ports in bore)RAINBOWUse L, BL, or multi-stone mandrel. Stone Use shorter stroke Use stone with lower length should be at least 1-1/2 times the length hardness number to length of bore for best bow correction (less overstroke)avoid part flexing FINISH TOO ROUGH*Decrease cutting Use finer grit stone Check oil to be sure Thoroughly true shoes For extremely fine pressure(one with higher grit you are using Sunnen to exact hole diameterfinishes in soft or number)Industrial Honing Oil*exotic material, use bronze mandrel or bronze shoes RANDOM SCRATCHESDecrease cutting Use finer grit stone Use softer stone If hard steel mandrel is Check oil to be pressure(one with higher grit (one with lower being used, change to sure you are using number)hardness number)soft steel mandrel. If Sunnen Industrial soft steel mandrel or Honing Oil*shoes are being used,change to bronze mandrel or shoes*Many honing problems, such as poor cutting action, poor stone life, and rough finish are caused by wrong honing oil, insufficient honing oil, dirty honing oil, or contaminated honing oil. Use only clean, full-strength Sunnen Industrial Honing Oil. Make sure that honing oil is neither diluted or "cut" with other oils. Keep solvents and cleaning fluids away from honing machine.{{FOR FAST STOCK REMOVAL IN DE-BURRED, BORED, REAMED OR GROUND HOLESFOR FINE FINISHING SOFT STEELHARDENED STEELIN PREVIOUSLHONED HOLES DIAMETER HONING FOR INCLUDIES: CAST STEELS HARD SOFT STEEL,SPINDLE OF BOREUNITDE-BURRING & STAINLESS STEELS FOR OCCASIONALFOR SOFT CAST IRON,CARBIDE GLASSS STEEL,BRONZE,CARBIDE,GLASSSPEED IN ROUGH (USE BRONZE MANDREL WORKPRODUCTION BRASSBRONZE &SOFT ALUMINUM CERAMICRPM HOLESOR SHOES IN WORK RUNS&CERAMIC * * *BRASSCAST IRON(MAX)STAINLESS STEEL)ALUMINUM * * *ALL FOR FOR TRY THIS IF FIRSTCHOICE MATERIALS OCCASIONALPRODUCTION STONE DOES NOT CUT,* *!!mm INCHES WORK WORK FIRST USE THIS STONE1,52- 2,03(0.060-0.080)D2D6-A67D6-A67D6-NM69D6-A65D6-A63D6-NM69D6-J63D6-J67D6-DM57D6-DM57D6-J93D6-J95D6-DR07D6-DR0730002,03- 2,54(0.080-0.100)D2D8-A67D8-A67D8-NM69D8-A65D8-A63D8-NM69D8-J63D8-J67D8-DM57D8-DM57D8-J93D8-J95D8-DR07D8-DR0730002,54- 3,05(0.100-0.120)K3K3-A611K3-A67K3-NM69K3-A65K3-A63K3-NM69K3-J63K3-J67K3-DM57K3-DM57K3-J93K3-J95K3-DMO7K3-DMO73000BU L3-A611L3-A67L3-NM69L3-A65L3-A63L3-NM69L3-J63L3-J67L3-DM57L3-DM57L3-J93L3-J95L3-DMO7L3-DMO73,05- 3,81(0.120-0.150)K4K4-A611K4-A67K4-NM69K4-A65K4-A63K4-NM69K4-J63K4-J67K4-DM57K4-DM57K4-J93K4-J95K4-DMO7K4-DMO73000BL4L4-A611L4-A67L4-NM69L4-A65L4-A63L4-NM69L4-J63L4-J67L4-DM57L4-DM57L4-J93L4-J95L4-DMO7L4-DMO73,81- 4,70(0.150-0.185)K5K5-A611K5-A67K5-NM69K5-A65K5-A63K5-NM69K5-J63K5-J57K5-DM57K5-DM57K5-J93K5-J95K5-DMO7K5-DMO73000BL5L5-A611L5-A67L5-NM69L5-A65L5-A63L5-NM69L5-J63L5-J57L5-DM57L5-DM57L5-J93L5-J95L5-DMO7L5-DMO74,70- 6,22(0.185-0.245)K6, JK6K6-A415K6-A57K6-NM69K6-A55K6-A63K6-NM69K6-J63K6-J57K6-DM57K6-DM57K6-J93K6-J95K6-DMO7K6-DMO73000L6, BL6L6-A413L6-A57L6-NM69L6-A55L6-A63L6-NM69L6-J63L6-J57L6-DM57L6-DM57L6-J93L6-J95L6-DMO7L6-DMO7K8, JK8K8-A413K8-A57K8-NM55K8-A55K8-A63K8-NM55K8-J63K8-J57K8-DM55K8-DM55K8-J93K8-J95K8-DMO5K8-DM056,22- 7,82(0.245-0.308)L8, BLS L8-A413L8-A57L8-NM55L8-A55L8-A63L8-NM55L8-J63L8-J57L8-DM55L8-DM55L8-J93L8-J95L8-DM05L8-DMO53000Y8Y8-A49Y8-A57'Y8-A55Y8-A63*Y8-J63Y8-J57****Y8-J93Y8-J95****K10, JK10K10-A413K10-A57K10-NM55K10-A55K10-A63K10-NM55K10-J63K10-J57K10-DM55K10-DM55K10-J93K10-J95K10-DM05K10-DMO57,82- 9,40(0.308-0.370)L10, BL10L10-A413L10-A57L10-NM55L10-A55L10-A63L10-NM55L10-J63L10-J57L10-DM55L10-DM55L10-J93L10-J95L10-DM05L10-DMO52000Y10Y10-A49Y10-A57*Y10-A55Y10-A63*Y10-J63Y10-J57****Y10-J93Y10-J95****K12, JK12K12-A413K12-A57K12-NM55K12-A55K12-A63K12-NM55K12-J63K12-J57K12-DM55K12-DM55K12-J93K12-J95K12-DM05K12-DMO516009,40- 12,57(0.370-0.495)L12, BL12L12-A413L12-A57L12-NM55L12-A55L12-A63L12-NM55L12-J63L12-J57L12-DM55L12-DM55L12-J93L12-J95L12-DMO5L12-DMO5to Y12Y12-A49Y12-A57*Y12-A55Y12-A63*Y12-J63Y12-J57****Y12-J93Y12-J95****2000K16, JK16K16-A413K16-A57K16-NM55K16-A55K16-A63K16-NM55K16-J63K16-J57K16-DM55K16-DM55K16-J93K16-J95K16-DMO5K16-DMO512,57- 15,72(0.495-0.619)L16, BL16L16-A413L16-A57L16-NM55L16-A55L16-A63L16-NM55L16-J63L16-J57L16-DM55L16-DM55L16-J93L16-J95L16-DMO5L16-DMO51270Y16Y16-A49Y16-A57"Y16-A55Y16-A63*Y16-J63Y16-J57**Y16-J93Y16-J95K20, JK20K20-A413K20-A57K20-NM55K20-A55K20-A63K20-NM55K20-J63K20-J57K20-DM55K20-DM55K20-J93K20-J95K20-DMO5K20-DMO515,72- 18,90(0.619-0.744)L20, BL20L20-A413L20-A57L20-NM55L20-A55L20-A63L20-NM55L20-J63L20-J57L20-DM55L20-DM55L20-J93L20-J95L20-DMO5L20-DMO51000P20P20-A413P20-A57P20-NM55P20-A55P20-A63P20-NM55P20-J63P20-J57P20-DM55P20-DM55P20-J93P20-J95P20-DMO5P20-DMO5Y20Y20-A411Y20-A57Y20-A55Y20-A63*Y20-J63Y20-J57""**Y20-J93Y20-J95AK20, JAK20K20-A413K20-A57K20-NM55K20-A55K20-A63K20-NM55K20-J63K20-J57K20-DM55K20-DM55K20-J93K20-J95K20-DMO518,90- 25,40(0.744-1.00)AL20, BAL20L20-A413L20-A57L20-NM55L20-A55L20-A63L20-NM55L20-J63L20-J57L20-DM55L20-DM55L20-J93L20-J95L20-OM05800P20P20-A413P20-A57P20-NM55P20-A55P20-A63P20-NM55P20-J63P20-J57P20-DM55P20-DM55P20-J93P20-J95P20-DMO5AAY20N20Y20-A411Y20-A57*Y20-A55Y20-A63*Y20-J63Y20-J57****Y20-J93Y20-J95**AK20, JAK20K20-A413K20-A57K20-NM55K20-A55K20-A63K20-NM55K20-J63K20-J57K20-DM55K20-DM55K20-J93K20-J95K20-DM05K20-DMO525,40- 26,19(1.000-1.031)AL20, BAL20L20-A413L20-A57L20-NM55L20-A55L20-A63L20-NM55L20-J63L20-J57L20-DM55L20-DM55L20-J93L20-J95L20-DMO5L20-DMO5640P28P28-A413P28-A57P28-NM55P28-A55P28-A63P28-NM55P28-J63P28-J57P28-DM55P28-DM55P20-J93P20-J95P20-DMO5P20-DMO5R28R28-A413R28-A57R28-NM55R28-A55R28-A63R28-NM55R28-J63R28-J57R28-DM55R28-DM55Y20-J93Y20-J95..AK20K20-A413K20-A57K20-NM55K20-A55K20-A63K20-NM55K20-J63K20-J57K20-DM55K20-DM55K20-J93K20-J95K20-DMO5K20-DMO526,19- 31,75(1.031-1.250)P28P28-A413P28-A57P28-NM55P28-A55P28-A63P28-NM55P28-J63P28-J57P28-DM55P28-DM55L20-J93L20-J95L20-DMO5L20-DMO5640R28R28-A413R28-A57R28-NM55R28-A55R28-A63R28-NM55R28-J63R28-J57R28-DM55R28-DM55P28-J93P28-J95P28-DMO5P28-DMO531,75- 92,08(1.250-3.625)P28P28-A413P28-A57P28-NM55P28-A55P28-A63P28-NM55P28-J63P28-J57P28-DM55P28-DM55P28-J93P8-J95P28-DMO5P28-DMO5640 to R28R28-A413R28-A57R28-NM55R28-A55R28-A63R28-NM55R28-J63R28-J57R28-DM55R28-DM55R28-J93R8-J95R28-DMO5R28-DMO550092,08-152,40(3.625-6.000)P28P28-A413P28-A57P28-NM55P28-A55P28-A63P28-NM55P28-J63P28-J57P28-DM55P28-DM55P28-J93P28-J95P28-DMO5P28-DMO5200R28R28-A413R28-A57R28-NM55R28-A55R28-A63R28-NM55R28-J63R28-J57R28-DM55R28-DM55R28-J93R28-J95R28-DMO5R28-DM0525,20- 34,93(0.992-1.375)Y32Y32-A49Y32-A57*Y32-A55Y32-A63*Y32-J63Y32-J57****Y32-J93Y32-J95****640 to 50034,67- 44,45(1.365-1.750)Y44Y44-A49Y44-A57*Y44-A55Y44-A63*Y44-J63Y44-J57****Y44-J93Y44-J95****500 to 40044,20- 57,15(1.740-2.250)Y56Y56-A49Y56-A57*Y56-A55Y56-A63*Y56-J63Y56-J57****Y56-J93Y56-J95****400 to 32056,90- 69,85(2.240-2.750)Y72Y72-A49Y72-A57*Y72-A55Y72-A63*Y72-J63Y72-J57****Y72-J93Y72-J95****320 to 25069,60- 82,55(2.740-3.250)Y88Y88-A49Y88-A57*Y88-A55Y88-A63*Y88-J63Y88-J57****Y88-J93Y88-J95****25082,30- 98,42(3.240-3.875)Y104Y104-A49Y104-A57*Y104-A55Y104-A63*Y104-J63Y104-J57****Y104-J93Y104-J95****20063,50- 68,58(2.500-2.700)AN-600G25-A47G25-A45*G25-A45G25-A63*G25-J63G25-J45G25-DV57G25-DV57G25-J85G25-J87G25-DV87**G25-DV87**25068,58-104,14(2.700-4.100)AN-600M27-A47M27-A45*M27-A45M27-A63*M27-J63M27-J45M27-DV57M27-DV57M27-J85M27-J87M27-DV87**M27-DV87**20088,90-139,70(3.500-5.500)AN-600N37-A47N37-A45*N37-A45N37-A63*N37-J63N37-J45N37-DV57N37-DV57N37-J85N37-J87N37-DV87**N37-DV87**20063,50- 83,82(2.500-3.300)AN-600GY25-A47GY25-A45*GY25-A45GY25-A63*GY25-J45GY25-J45****GY25-J85GY25-J85****250GG25-A47GG25-A45*GG25-A45GG25-A63*GG25-J45GG25-J45****GG25-J85GG25-J85****83,82-106,68(3.300-4.200)AN-600MY33-A47MY33-A45*MY33-A45MY33-A63*MY33-J45MY33-J45****MY33-J85MY33-J85****200MM33-A47MM33-A45*MM33-A45MM33-A63*MM33-J45MM33-J45****MM33-J85MM33-J85****101,60-142,24(4.000-5.600)AN-600NY40-A47NY40-A45*NY40-A45NY40-A63*NY40-J45NY40-J45****NY40-J85NY40-J85****200NN40-A47NN40-A45*NN40-A45NN40-A63*NN40-J45NN40-J45****NN40-J85NN40-J85****ABRASIVE TYPESGRIT SIZEHARDNESSRECOMMENDED STONESGRIT SIZEMATERIAL ABRASIVE TYPE 801001502202803204005006001200HARD ALUMINUM OXIDE 25 / 0,65–20 / 0,5018 / 0,4512 / 0,3010 / 0,25 5 / 0,12 3 / 0,08 1 / 0,03–STEEL SILICON CARBIDE CBN/BORAZON ®–55 / 1,4045 / 1,1540 / 1,0028 / 0,70–20 / 0,50–7 / 0,18 2 / 0,05SOFT ALUMINUM OXIDE 80 / 2,00–35 / 0,9025 / 0,6520 / 0,5016 / 0,407 / 0,18 4 / 0,10 2 / 0,05–STEEL SILICON CARBIDE CBN/BORAZON ®–65 / 1,60–70 / 1,75––25 / 0,65–16 / 0,40 5 / 0,12CAST SILICON CARBIDE 100 / 2,50–30 / 0,7520 / 0,5012 / 0,30– 6 / 0,15 5 / 0,12 3 / 0,08–IRON DIAMOND –––80 / 2,00––50 / 1,27–20 / 0,5012 / 0,30ALUMINUM,SILICON CARBIDE 170 / 4,30–80 / 2,0055 / 1,4033 / 0,8527 / 0,7016 / 0,4012 / 0,30 2 / 0,05–BRASS, BRONZE CARBIDE DIAMOND ––30 / 0,7520 / 0,50––7 / 0,18– 3 / 0,08 1 / 0,03CERAMIC DIAMOND ––50 / 1,2740 / 1,00––20 / 0,50–15 / 0,4010 / 0,25GLASSDIAMOND––95 / 2,4070 / 1,80––30 / 0,75–15 / 0,408 / 0,20SUNNEN STONE GUIDEAPPROXIMATE SURFACE FINISH IN MICROINCHES R A / MICROMETERS (MICRONS) R A* CBN/Borazon stones available on special order. !CBN/Borazon stones available on special order. ** CBN/Borazon stones available on special order.*** CBN/Borazon stones available on special order.FINISH FIGURES BASD ON USE OF SUNNEN HONING OIL. IN GENERAL, USE OF WATER BASED COOLANTS RESULT IN FINER SURFACE FINISH AND REDUCED METAL REMOVAL RATES.A—ALUMINUM OXIDE C —SILICON JCARBIDE DM DR —DIAMONDDV NM CBN /NR —NVBORAZON1—702—803—1004—1505—2206—2807—3208—4009—5000—60090—90000—12001—SOFT2—3—5—7—11—15—HARDK8 –A57SERIES ABRASIVE GRIT HARD-TYPE SIZE NESS}}}HONING GUIDEInformation shown is applicable to (conventional) stones, which must be used with honing oil, and NM & DM stones (metal bond)which may be used with either honing oil or water based coolant. The process fluid is very important. Many honing problems,such as poor cutting action, poor stone life, and rough finish are traceable to the process fluid. In general, honing performance will be reduced when water based coolants are used.。
プレスの専门用语
サイレンサ メントリ（面取り） クリップ センサー ピッチ ロクタイト（接着剤） タスクホース 呼び ジャッキ バランス バランサー 平ら カウンター ボルスター ベッドオープニング エアレリース ジャミング ガイド ダンク メモリ 扉 カウンター プリセット トータル フィード ライニング ネジジャッキ バス パス プリセットカウンタ アクリルカバー タイマーオフ 桁 トータル エジェクタ フュルト クリーナー 巻き取り機 ターンテーブル パットライト ぼうおんbox
英文
冲压机 升降叉车 卷线机 捻线机 打磨机 装料机 切线机 车床 钻床 铣床
汉语
日语
ハンモック アングル バロメーター オペレーション 上型（うえかた） 下型（したかた） 導入 パンチ グラインダー ビシャモン ラジオペンチ サイレンサー マフラースタンド ダクトー アグプタ アウトーレット（？） アクセサリ アプリケータ アライメント ソケット
jamming guide trough memo counter preset total feed lining buss pass preset timer off total ejector cleaner turn table alarm(light)
英文
Hammock angle operation upperdie lowerdie punch grinder radio pencher silencer stand duct adapter outlet accessory applicator alignment socket
spline micro meter 异型千分尺
hoist striker strip
crane
Vacuum tube for milking machine
专利名称：Vacuum tube for milking machine发明人：宮下 明彦申请号：JP実願平6-241申请日：19940128公开号：JP第3003211号U公开日：19941018专利内容由知识产权出版社提供专利附图：摘要：(57)< Abstract > < Objective > Although configuration being simple, themultiple tubesThe joint physical relationship of the multiple tube which was formed to one body permitting/insertingBe able to identify in divination, at the same time being cheap, for milking machine which does not have discoloration and decolorizationThe vacuum tube is offered. < Constitution > In the milking machine which milks with the vacuum pressure useThe multiple tubes which consist of the re and the flexibility tube substantial one deformationBeing constituted possibly, just the vacuum tube smell of becomingThe te, at least outer part cross section 3 of the tube of edge side ofoneDifference with the outer part cross section of other tube 2 featureWith the vacuumtube for the milking machine which is done.申请人：オリオン機械株式会社地址：長野県須坂市大字幸高246番地国籍：JP更多信息请下载全文后查看。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
锁定转子加热测试和运行测试进行了铝辐射板的大小表示如下。
电机的齿轮
头,齿轮相反的测试进行了辐射板
A Running Heating TEST AND A LOCKED-ROTOR TEST HAS BEEN CONDUCTED WITH A ALUMINUM RADIATION PLATE OF SIZE INDICATED BELOW. FOR THE MOTOR WITH A GEAR HEAD ,TESTS HAS BEEN CONDUCTED WITH A GEAR INSTEAD OF THE RADIATION PLATE
东方电机
ORIENTAL MOTOR
通用交流伺服
GENERAL PURPOSE AC SERVO
安全使用交流伺服
TO USE THE AC SERVO SAFELY
表的内容TABLE OF CONTENTS
设置打印机SETTING UP YOUR PRINTER
使用您的打印机软件USING YOUR PRINTER SOFTWARE
创造性的印刷CREATIVE PRINTING
使用和照顾你的喷墨打印CARTRIDES USING AND CARING FOR YOUR INKJET PRINT CARTRIDES
得到帮助当事情出错GETTING HELP WHEN THINGS GO WRONG
更多关于你的PRINTRE和供应MORE ABOUT YOUR PRINTRE AND SUPPLIES
附录A规范APPENDIX A SPECIFICATIONS
检查你的电脑设置CHECKING YOUR COMPUTER SETTINGS
致动器一般目录ACTUATORS GENERAL CATALOG
各级夹具CYLIN C系列JIG CYLIN DERS C SERIES
新钢笔气缸NEW PEN CYLINDERS
苗条的气缸slim cylinders
广泛的变化wide variation
nok铁橡胶nok iron rubber
unitta 带目录unitta belt catalogue
小金属平面弹性联轴器small metal flat spring coupling
The HC products are applied in thermoforming machines, PET stretch blow molding machines, dry/cure (i.e. paint) or general material heating. We supply machine builders having the necessary automation expertise to implement our controllers. Our system partners, offers complete retrofits for heater control in existing machines.
我们开发、制造商和市场力量控制器用于ofens的电加热元件(暖气)
为工业加热过程。
HC(加热控制器)需要更少的空间在一个电控箱SSR相比,固态继电器控制。
当打开加热器需要检测HC的解决方案是便宜那么PLC(流程逻辑控制器)控制SSR。
我们的产品最适合我们的客户提供多种控制平台的应用程序。
HC的控制单个加热器和多个加热器(区)单独优化热剖面。
HC产品应用于热成型机器,宠物拉伸吹塑机械、干燥/治疗(即油漆)或通用材料加热。
我们供应自动化机械制造商拥有必要的专业知识来实现我们的控制器。
我们的系统合作伙伴,均提供完整的加热器控制现有的机器。