美孚合成齿轮油SHC629系列产品技术说明书

合集下载

Mobilgear SHC 46M 高技术、超高粘度、合成开式齿轮油说明书

Product Data Sheet Mobilgear SHC 46MHigh Technology, Ultra High Viscosity,Synthetic Open Gear Oil Product DescriptionMobilgear SHC 46M is a speciality ultra high viscosity lubricant primarily intended for use in heavily loaded, low and medium speed gears where boundary lubrication conditions prevail.Mobilgear SHC 46M is formulated from wax-free synthetic base stocks which have exceptional oxidation and thermal properties and remarkable excellent low-temperature fluidity. The combination of a naturally highviscosity index and a unique additive system enables the product to provide outstanding performance under severe high and low temperature operating conditions. The base stocks have inherently low traction properties which result in low fluid friction in the load zone of non-conforming surfaces such as gears. Reduced fluidfriction produces lower oil operating temperatures and improved gear efficiency.Mobilgear SHC 46M exceeds Falk minimum viscosity requirements for intermittent lubrication of gears.Mobilgear SHC 46M does not contain any solvent.BenefitsMobilgear SHC 46M offers the following benefits:•Extended gear life resulting from outstanding load-carrying, anti-wear and tackiness properties derived from proprietary thick film lubrication•Reduction in pump replacement costs due to their pumpability at ambient temperature•Improved safety gear efficiency and lower operating temperatures arising from low traction properties •Reduced lubricant consumption and disposal costs•Absence of hard-packed deposits and the elimination of the need for gear cleaning with subsequent reduction in downtime and maintenance costs•Improved safety through absence of solvent•Easier distribution/meteringApplicationMobilgear SHC 46M is primarily recommended for open gears where asphaltic, diluent-containing lubricantshave historically been used. Mobilgear SHC 46M is also recommended for the replacement of semi-fluid greases.Mobilgear SHC 46M can be applied with conventional single line or dual line spray systems without costly circulation system modifications. It is pumpable at temperatures as low as +6°C but, at lower temperatures, the product may have to be heated to achieve the proper spray distribution pattern.Health and SafetyBased on available toxicological information, it has been determined that this product poses no significant health risk when used and handled properly.Details on handling, as well as health and safety information, can be found in the Material Safety Data Bulletin which can be obtained through Mobil Oil Company Ltd., by telephoning 01372 22 2000.Typical physical characteristics are given in the table. These are intended as a guide to industry and are not necessarily manufacturing or marketing specifications.Typical CharacteristicsMobilgear SHC 46MTest MethodISO VG-46000Viscosity, cSt at 40ºC ASTM D4*******Viscosity, cSt at 100ºC ASTM D4451250Viscosity Index ASTM D2270210Specific Gravity ASTM D12980.924Flash Point, ºC ASTM D92228Pour Point, ºC ASTM D97+6Rust Protection, Distilled Water ASTM D665PassRust Protection, Synthetic Sea Water ASTM D665PassCopper Corrosion ASTM D1301A/1BTimken OK Load, kg ASTM D250926.7FZG Gear Test, Fail Stage DIN 5135412+4-Ball Wear, Scar mm ASTM D22660.9754-Ball Weld Load, kg ASTM D2596315Colour ASTM D1500 1.5Due to continual product research and development, the information contained herein is subject to change without notice.Mobil Oil Company LimitedActing as Agent for Mobil Lubricants UK LimitedExxonMobil House, Ermyn WayLeatherhead, Surrey, KT22 8UXTelephone: 01372 22 2000。

Mercon ULV自动变速箱油产品说明说明书

SAFETY DATA SHEET1. IdentificationMERCON ULV AUTOMATIC TRANSMISSION FLUIDProduct identifierOther means of identification196825FIR No.Automatic Transmission FluidRecommended useNone known.Recommended restrictionsManufacturer/Importer/Supplier/Distributor informationFord Motor CompanyCompany NameAttention: SDS Information, P.O. Box 1899AddressDearborn, Michigan 48121USA1-800-392-3673Telephone1-800-448-2063 (USA and Canada)SDS InformationEmergency telephonenumbersPoison Control Center: USA and Canada: 1-800-959-3673INFOTRAC (Transportation): USA and Canada 1-800-535-50532. Hazard(s) identificationNot classified.Physical hazardsAspiration hazardCategory 1Health hazardsNot classified.Environmental hazardsNot classified.OSHA defined hazardsLabel elementsSignal word DangerHazard statement May be fatal if swallowed and enters airways.Precautionary statementPrevention Observe good industrial hygiene practices.Response If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting. Take offcontaminated clothing and wash it before reuse.Storage Store locked up.Disposal Dispose of contents/container in accordance with local/regional/national/international regulations. Hazard(s) not otherwiseNone known.classified (HNOC)Supplemental information None.3. Composition/information on ingredientsMixturesCAS number% Chemical name Common name and synonyms89 - 90Distillates (petroleum), hydrotreated64742-55-8light paraffinicSpecific chemical identity and/or exact percentage (concentration) of composition has been withheld as a trade secret.4. First-aid measuresMove to fresh air. Call a physician if symptoms develop or persist.Inhalation Wash off with soap and water. Get medical attention if irritation develops and persists.Skin contact Rinse with water. Get medical attention if irritation develops and persists.Eye contact Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs.IngestionAspiration may cause pulmonary edema and pneumonitis.Most importantsymptoms/effects, acute and delayedProvide general supportive measures and treat symptomatically. Keep victim under observation.Symptoms may be delayed.Indication of immediatemedical attention and special treatment needed Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves.General information5. Fire-fighting measuresWater fog. Foam. Dry chemical powder. Carbon dioxide (CO2).Suitable extinguishing media Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishing mediaDuring fire, gases hazardous to health may be formed. Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons.Specific hazards arising from the chemicalSelf-contained breathing apparatus and full protective clothing must be worn in case of fire.Special protective equipment and precautions for firefighters Move containers from fire area if you can do so without risk.Fire fightingequipment/instructions Use standard firefighting procedures and consider the hazards of other involved materials.Specific methods No unusual fire or explosion hazards noted.General fire hazards6. Accidental release measuresAvoid contact with eyes, skin, and clothing. Avoid inhalation of vapors and spray mists. Ensure adequate ventilation. Keep people away from and upwind of spill/leak. Keep unnecessarypersonnel away. Local authorities should be advised if significant spillages cannot be contained.Wear appropriate protective equipment and clothing during clean-up. For personal protection, see section 8 of the SDS.Personal precautions,protective equipment and emergency proceduresThe product is immiscible with water and will spread on the water surface.Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS.Methods and materials for containment and cleaning upAvoid discharge into drains, water courses or onto the ground.Environmental precautions7. Handling and storageAvoid contact with eyes, skin, and clothing. Avoid breathing mist or vapor. Avoid prolongedexposure. Provide adequate ventilation. Observe good industrial hygiene practices. Wash hands thoroughly after handling. Wear appropriate personal protective equipment. For personal protection, see Section 8 of the SDS.Precautions for safe handlingStore locked up. Store in tightly closed container. Store away from incompatible materials (see Section 10 of the SDS).Conditions for safe storage,including any incompatibilities8. Exposure controls/personal protectionOccupational exposure limitsThe following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.At this time, the other constituents have no known exposure limits.US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)Form Value Components Type PEL5 mg/m3Mist.Distillates (petroleum),hydrotreated light paraffinic (CAS 64742-55-8)US. ACGIH Threshold Limit Values FormValue ComponentsType TWA5 mg/m3Inhalable fraction.Distillates (petroleum),hydrotreated light paraffinic (CAS 64742-55-8)US. NIOSH: Pocket Guide to Chemical Hazards Form Value Components Type STEL10 mg/m3Mist.Distillates (petroleum),hydrotreated light paraffinic (CAS 64742-55-8)TWA 5 mg/m3Mist.No biological exposure limits noted for the ingredient(s).Biological limit values Use adequate ventilation to control airborne concentrations below the exposure limits/guidelines. If user operations generate a vapor, dust and/or mist, use process enclosure, appropriate local exhaust ventilation, or other engineering controls to control airborne levels below the recommended exposure limits/guidelines.Appropriate engineering controlsIndividual protection measures, such as personal protective equipmentWear safety glasses with side shields (or goggles).Eye/face protectionSkin protectionSuitable chemical protective gloves should be worn when the potential exists for skin exposure.The choice of an appropriate glove does not only depend on its material but also on other quality features and is different from one producer to the other. Nitrile gloves are recommended.Hand protectionWear appropriate chemical resistant clothing if applicable.OtherIf engineering controls do not maintain airborne concentrations to a level which is adequate to protect worker health, an approved respirator must be worn. Respirator selection, use and maintenance should be in accordance with the requirements of OSHA Respiratory Protection Standard 29 CFR 1910.134 and/or Canadian Standard CSA Z94.4.Respiratory protectionWear appropriate thermal protective clothing, when necessary.Thermal hazards Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants.General hygiene considerations9. Physical and chemical propertiesAppearanceLiquid.Physical state Liquid.Form Red.Color PETROLEUM OdorOdor threshold Not available.pHNot available.Melting point/freezing point Not available.Initial boiling point and boiling range Not available.Flash point > 314.6 °F (> 157.0 °C) Pensky-Martens Closed Cup Evaporation rate Not available.Not applicable.Flammability (solid, gas)Upper/lower flammability or explosive limits Explosive limit - lower (%)Not available.Explosive limit - upper (%)Not available.Vapor pressure< 1 mm HgVapor density > 1 (Air=1)Relative density0.83 - 0.85 (Water=1)Relative density temperature 60.08 °F (15.6 °C)Solubility(ies)Solubility (water)Negligible Partition coefficient (n-octanol/water)Not available.Auto-ignition temperature Not available.Decomposition temperature Not available.Viscosity19 - 20 cSt Viscosity temperature104 °F (40 °C)10. Stability and reactivityThe product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity Material is stable under normal conditions.Chemical stability No dangerous reaction known under conditions of normal use.Possibility of hazardous reactionsContact with incompatible materials.Conditions to avoid Strong oxidizing agents.Incompatible materials Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons.Hazardous decomposition products11. Toxicological informationInformation on likely routes of exposureInhalationBased on available data, the classification criteria are not met. Prolonged inhalation may be harmful.Skin contact Based on available data, the classification criteria are not met.Eye contact Based on available data, the classification criteria are not met.IngestionDroplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious chemical pneumonia.Symptoms related to the physical, chemical andtoxicological characteristics Aspiration may cause pulmonary edema and pneumonitis.Information on toxicological effectsAcute toxicityMay be fatal if swallowed and enters airways.Prolonged skin contact may cause temporary irritation.Skin corrosion/irritation Direct contact with eyes may cause temporary irritation.Serious eye damage/eye irritationRespiratory or skin sensitizationRespiratory sensitizationNot a respiratory sensitizer.This product is not expected to cause skin sensitization.Skin sensitization No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic.Germ cell mutagenicity CarcinogenicityNot classifiable as to carcinogenicity to humans.IARC Monographs. Overall Evaluation of CarcinogenicityNot listed.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)Not listed.This product is not expected to cause reproductive or developmental effects.Reproductive toxicitySpecific target organ toxicity -single exposureNot classified.Specific target organ toxicity -repeated exposureNot classified.Aspiration hazard May be fatal if swallowed and enters airways.Chronic effectsProlonged inhalation may be harmful.12. Ecological informationThe product is not classified as environmentally hazardous. However, this does not exclude the possibility that large or frequent spills can have a harmful or damaging effect on the environment.EcotoxicityNo data is available on the degradability of any ingredients in the mixture. Persistence and degradabilityBioaccumulative potential No data available.Mobility in soil Other adverse effectsNo other adverse environmental effects (e.g. ozone depletion, photochemical ozone creationpotential, endocrine disruption, global warming potential) are expected from this component.13. Disposal considerationsCollect and reclaim or dispose in sealed containers at licensed waste disposal site. Dispose of contents/container in accordance with local/regional/national/international regulations. Don't pollute. Conserve resources. Return used oil to collection centers.Disposal instructionsDispose in accordance with all applicable regulations.Local disposal regulations The waste code should be assigned in discussion between the user, the producer and the waste disposal company.Hazardous waste code Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see:Disposal instructions).Waste from residues / unused productsSince emptied containers may retain product residue, follow label warnings even after container is emptied. Empty containers should be taken to an approved waste handling site for recycling or disposal.Contaminated packaging14. Transport informationDOTNot regulated as dangerous goods.IATANot regulated as dangerous goods.IMDGNot regulated as dangerous goods.Not established.Transport in bulk according toAnnex II of MARPOL 73/78 and the IBC Code15. Regulatory informationThis product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.US federal regulationsToxic Substances Control Act (TSCA)TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)Not regulated.CERCLA Hazardous Substance List (40 CFR 302.4)Not listed.SARA 304 Emergency release notificationNot regulated.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)Not listed.SARA 302 Extremely hazardous substanceSuperfund Amendments and Reauthorization Act of 1986 (SARA)Not listed.YesSARA 311/312 Hazardous chemicalAspiration hazardClassified hazard categoriesSARA 313 (TRI reporting)Not regulated.Other federal regulationsClean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) ListNot regulated.Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)Not regulated.Not regulated.Safe Drinking Water Act(SDWA)International InventoriesAll components are listed or are exempt from listing on the Toxic Substances Control Act Inventory.16. Other information, including date of preparation or last revision08-20-2021Issue date Version 01Health: 0Flammability: 1Physical hazard: 0HMIS® ratingsHealth: 0Flammability: 1Instability: 0NFPA ratingsThis document was prepared by FCSD-Toxicology, Ford Motor Company, Diagnostic Service Center II, 1800 Fairlane Drive, Allen Park, MI 48101, USA, based in part on information provided by the manufacturer. The information on this data sheet represents our current data and is accurate to the best of our knowledge as to the proper handling of this product under normal conditions and in accordance with the application specified on the packaging and/or technical guidance literature. Any other use of the product which involves using the product in combination with any other product or any other process is the responsibility of the user. To the extent that there are any differences between this product’s Safety Data Sheet (SDS) and the consumer packaged product labels, the SDS should be followed.Preparation Information and DisclaimerXT-12-QULV, XT-12-QULV1Part number(s)。

齿轮油安全技术说明书(MSDS)

精心整理齿轮油安全技术说明书MSDS第一部分：化学品名称化学品中文名称：齿轮油化学品英文名称：第二部分：成分/组成信息主要组成基础油抗磨剂极压抗磨剂油性剂防锈剂抗氧剂需要披露的有害物质或有害复合物1-*危险特性：遇明火、高热或与氧化剂接触，有引起燃烧爆炸的危险。

若遇高热，容器内压增大，有开裂和爆炸的危险。

有害燃烧产物： 1.可能分解出一氧化碳及二氧化碳气体。

2.烟气。

3.乙醛,硫氧化物。

灭火方法：使用消防水雾、泡沫、干化学制剂(干粉)或者二氧化碳(CO2)灭火，不能用水灭火。

消防说明疏散该地区。

?防止控制火灾或稀释的流出液流入河川、下水道或饮水源。

?消防员应使用标准防护设备,在密闭空间需使用自给式呼吸器(SCBA)。

?用喷水的方式使暴露于火灾的表面降温并保护工作人员。

闪点>210C(410F)[ASTMD-92] 爆炸下限(LEL) 0.9 自燃温度未制定爆炸上限（UEL）7.0第六部分：泄漏应急处理应急处理：迅速撤离泄漏污染区人员至安全区，并进行隔离，严格限制出入。

切断火源。

建议应急处理人员戴自给正压式呼吸器，穿一般作业工作服。

尽储存注意事项： 1.使用适当设计及保养的机械通风系统,如整体换气装置或局部排气装置。

2.以局部排气装置及必要的制程隔离以控制雾滴及蒸气量。

3.供给充分新鲜空气以补充排气系统抽出的空气。

4.可能需要处理发散的废气以免污染环境。

5.置于室内环境,保持油品密封，不可与易燃、易爆化学品摆在一起。

6.不可存放于开口或者无标识容器中。

静电集电物:?? 本产品蓄积静电。

第八部分：接触控制/个体防护监测方法：密闭操作，注意通风。

工程控制：防护级别和所需的控制措施的种类根据潜在的接触条件不同而不同。

可供选择的控制措施包括:?在通常使用环境和充分通风条件下没有特殊要求。

当空气中浓度超标时，建议佩戴自吸过滤式防毒面具（半面罩）。

紧急事态抢救或撤离时，应该佩戴空气呼吸器。

个人防护：选择个人防护设备因可能的接触条件,如应用领域、处理工作、浓度和通风等而异。

美孚SHC624齿轮油

美孚SHC624合成齿轮油
美孚SHC624合成齿轮油是用美孚独有的合成油专有技术与优良的添加剂配方调制而成，氧化稳定性大大增强，抗泡性能得到提高，即使在含水条件下性能仍保持超级稳定，同时具有出色的防锈防腐及减磨性能。

与传统的矿物油相比，合成基础油可提供更长的使用寿命，具有天然的更高的粘度指数。

美孚SHC600系列合成齿轮油同时具有低牵引系数和高粘度指数，可显著地降低动力消耗。

设备较低的工作温度意味着摩擦已经降低，因而较少的动力消耗。

最终，设备的寿命得到延长，设备的设计可以更经济，油品的使用寿命也同时得到了延长。

此系列齿轮油包含了美孚SHC624|626|627|629|630|632|634|636|639.
产品优点：
1. 更好的高温氧化稳定性
2. 增强了的低温流动性
3. 更低的工作温度
4. 油品使用寿命延长
5. 动力消耗减少
6. 泡沫控制改进
7.含水条件下保持超级稳定（水解稳定性和抗乳化性）
8.出色的防锈防腐性
产品应用：
美孚SHC624合成齿轮油推荐用于广阔工作温度范围内工业轴承及齿轮的润滑。

尤其对于下述情形最为适合，即高温时油品寿命短，因部件更换、系统清洗和更换滑油而造成维护费用高等。

美孚SHC 625、627、629及630适用於注油回转螺杆式压缩机，供压缩天然气、矿场收集的天然气、二氧化碳及其他在天然气行业采用的加工气体。

美孚齿轮油型号

美孚齿轮油型号美孚齿轮油SHC XMP 系列美孚齿轮油SHC XMP 150 Mobilgear SHC XMP 150 美孚齿轮油SHC XMP 220 Mobilgear SHC XMP 220 美孚齿轮油SHC XMP 320 Mobilgear SHC XMP 320 美孚齿轮油SHC XMP 460 Mobilgear SHC XMP 460 美孚齿轮油SHC XMP 680 Mobilgear SHC XMP 680美孚齿轮油SHC系列美孚齿轮油SHC 150 Mobilgear SHC 150美孚齿轮油SHC 220 Mobilgear SHC 220美孚齿轮油SHC 320 Mobilgear SHC 320美孚齿轮油SHC 460 Mobilgear SHC 460美孚齿轮油SHC 680 Mobilgear SHC 680美孚SHC600系列美孚SHC 624 Mobil SHC 624美孚SHC 626 Mobil SHC 626美孚SHC 627 Mobil SHC 627美孚SHC 629 Mobil SHC 629美孚SHC 630 Mobil SHC 630美孚SHC 632 Mobil SHC 632美孚SHC 634 Mobil SHC 634美孚SHC 636 Mobil SHC 636美孚SHC 639 Mobil SHC 639美孚齿轮油格高系列美孚格高 68 齿轮油 Mobil Glgoyle 68美孚格高 100 齿轮油 Mobil Glgoyle 100美孚格高 150齿轮油 Mobil Glgoyle 150美孚格高 220齿轮油 Mobil Glgoyle 220美孚格高 320齿轮油 Mobil Glgoyle 320美孚格高 460 齿轮油 Mobil Glgoyle 460美孚格高 680 齿轮油 Mobil Glgoyle 680美孚格高 1000 齿轮油 Mobil Glgoyle 1000美孚格高系列11，22，30美孚格高11-合成循环/齿轮油 Mobil Glygoyle 11 美孚格高22-合成循环/齿轮油Mobil Glygoyle 22 美孚格高30-合成循环/齿轮油 Mobil Glygoyle 30 美孚超级齿轮油600 XP系列美孚超级齿轮油600 XP 68 Mobilgear 600 XP 68美孚超级齿轮油600 XP 100 Mobilgear 600 XP 100美孚超级齿轮油600 XP 150 Mobilgear 600 XP 150 美孚超级齿轮油600 XP 220 Mobilgear 600 XP 220美孚超级齿轮油600 XP 320 Mobilgear 600 XP 320美孚超级齿轮油600 XP 460 Mobilgear 600 XP 460美孚超级齿轮油600 XP 680 Mobilgear 600 XP 680美孚齿轮油XMP系列美孚齿轮油 XMP 68， Mobilgear XMP 68美孚齿轮油 XMP 100，Mobilgear XMP 100美孚齿轮油 XMP 150，Mobilgear XMP 150美孚齿轮油 XMP 220，Mobilgear XMP 220美孚齿轮油 XMP 320，Mobilgear XMP 320美孚齿轮油 XMP 460，Mobilgear XMP 460美孚齿轮油 XMP 680，Mobilgear XMP 680美孚齿轮油型号—【加多力】主营产品:工业润滑油，齿轮油，液压油,润滑脂（黄油），空气压缩机油,变压器油,导热油,导轨油，轧制液,防锈油,切削油，水溶性切削液,冲压机油,,柴油机油,白矿油,锭子油,高温润滑脂,水基清洗剂等。

金美孚参数

金美孚参数
金美乎参数是指金美乎(Mobi)品牌的润滑油产品的性能和规格参数。

以下是关于会美乎洞滑油的参数:
1.枯度等级:根据枯高等级，金美手润滑油产品分为不同系列，如
5W.30. 10W-40等。

这些数字表示油的粘度和流动性能，其中W表示冬事使用。

2AP服务分类:金美乎润滑油按API (美国石油协会)标准进行分类，如APISN. APC14等这些分类表示油的性能和应用领域。

此外，还有一其他的性能指标，如运动粘度密封性.润海抗奢性能。

音和机油消耗等，
以上信息仅供参考，建议咨询专业人士获取准确的信息，。

美孚齿轮油SHC系列

美孚齿轮油SHC系列（Mobilgear SHC Series）详细信息：Mobilgear SHC Series (美孚齿轮油SHC系列)齿轮油产品简介美孚齿轮油SHC系列是优异性能的重负荷齿轮油，供所有类型的密封式齿轮及滑动与滚动元件轴承使用。

本产品在设备保护、润滑油寿命和无故障作业方面提供出色的服务，提高顾客的生产率。

这些科学设计的合成润滑油由合成基础液配制而成，具有出色的抗氧化与热稳定特性及低温流动性。

固有的高粘度指数和独特的添加剂配方结合，使本系列产品在严苛的高、低温工作条件下表现杰出。

合成基础油的本质，还使产品具有优异的低温性能。

它们具有杰出的极压性，并能承受冲击负荷。

合成基础油先天所具有的低牵引力特性，能使处在不规则表面，如齿轮和滚动元件轴承负荷区的流体摩擦降低。

流体摩擦降低，可降低工作温度，因而能够提高齿轮的效率。

美孚齿轮油SHC系列产品的粘度范围广，介於ISO VG 150至6800之间。

因此可用於大量密封式齿轮传动装置中，也适合滑动与滚动元件轴承使用。

由於具有粘度等级高的种类，本系列润滑油可以满足极低速、高负荷/高温工作的齿轮与轴承的要求，对於处於边界润滑条件下的传统产品，它们是理想的代替品。

在使用润滑油浴或循环系统施用润滑油的情况下，它们可用于润滑开式齿轮。

由於用途广泛，在艰难的工作条件下性能极佳，因此美孚齿轮油SHC系列润滑油是世界上许多原设备制造商和用户选用的产品。

特性与优点美孚齿轮油SHC系列是Mobil SHC品牌产品中的先进产品，因其创新及杰出的性能而享誉全球。

这些科学设计的合成润滑油表明了本公司不断致力于采用先进技术提供卓越润滑油产品的努力。

Mobilgear SHC润滑油具备许多矿物油所缺乏的优点，尤其是在极高和极低温的作业条件下，具有优异的性能特点和用户效益。

我们的配方科学家采用专利的添加剂系统结合强化的基础油，使它即使处在冲击负荷的情况下，仍保持优异的极压性能与抗磨损性能。

Mobilgear 629 (中文)

610865-00 MOBILGEAR 629产品安全技术说明书第一部分产品和企业标识产品名称：MOBILGEAR 629 供应商名称、地址及电话：埃克森美孚（中国）投资有限公司上海市天钥桥路30号美罗大厦 200030 86-21-5464 4588紧急联络电话：86-21-5464 4588传真电话：86-21-6427 0570第二部分成分/组成信息化学名称和别名：石油碳氢化合物和添加剂。

全球报告的MSDS成分：无。

接触限值（若适用）见第8部分。

第三部分危险性概述在正常使用条件下，依照法规认为本品无害（参见15部分）。

应急综述：微浊琥珀色液体。

美国运输部（DOT）紧急情况响应指导书（ERG）编号: 不适用。

潜在健康影响：在正常的预期使用条件下，本品对健康没有危险。

过度接触会引起眼睛、皮肤或呼吸刺激。

进一步的健康影响/毒理学资料参见第11部分。

第四部分急救措施眼睛接触：用清水彻底冲洗。

若出现刺激，就医。

皮肤接触：用肥皂和清水冲洗污染皮肤。

脱掉被油浸湿的衣服并洗干净，清洗污染皮肤。

（参见第16部分-注射伤害）。

吸入：一般不会有问题。

但是，如果由于过多接触蒸气或雾出现呼吸刺激、眩晕、恶心或神志不清，立即就医。

如果呼吸停止，用机械装置或口对口的方式进行人工呼吸。

食入：一般不会有问题。

若感觉不适，就医。

禁止催吐。

第五部分消防措施灭火剂：二氧化碳、泡沫、干粉和雾状水。

特殊灭火程序：用水或泡沫灭火可导致喷沫。

用水冷却暴露在火场中的容器。

可使用雾状水从暴露区域冲走泄漏物。

防止泄漏物从受控的火场流出或被稀释后排入河流、下水道或饮用水供应系统。

防护器具：在封闭的区域灭火，消防员必须佩戴自给式呼吸器。

异常燃爆危险：无。

燃烧产物：在不完全燃烧的情况下，有浓烟、一氧化碳、硫的氧化物、醛和其它分解产物。

闪点℃（℉）：204 (399) (ASTM D-92)。

美孚高温润滑脂系列（Mobiltemp

美孚⾼温润滑脂系列（Mobiltemp SHC Series）美孚⾼温润滑脂SHC系列产品为性能超卓之防磨损润滑脂，主要⽤于⾼温作业条件。

该产品结合了聚？烯烃(PAO)合成基础液和有机粘⼟⽆皂增稠剂的独特之处。

PAO基出⾊的抗热/抗氧化降解性能加上粘⼟增稠剂出⾊的⾼温结构稳定性和⾼滴点，制成了这种卓越的⾼温润滑脂。

合成基础液的⽆蜡性质及其⾼粘度指数也提供极佳的低温润滑以及⾼温条件下出⾊的油膜保护。

鉴于 PAO基础油具有低牵引特性（与矿物油相⽐），美孚⾼温滑脂 SHC系列还因减少摩擦和低扭矩以及降低轴承滚动元件负荷区的温度⽽具有节能潜⼒。

美孚⾼温滑脂 SHC 系列有三个产品：Mobiltemp SHC 32 为 NLGI 1 1/2 等级润滑脂，采⽤ ISO VG 32 基础油； Mobiltemp SHC 100 为 NLGI 2等级润滑脂，采⽤ ISO VG 100 基础油；Mobiltemp SHC 460 Special 为NLGI 1等级润滑脂，采⽤ISO VG 460 基础油，加上⼆硫化钼以增添额外防磨保护。

美孚⾼温润滑脂 SHC系列润滑脂⽤于各种⾼温⽤途以及需要低温起动或额定转速转矩的应⽤。

它们在⾼温下具有出⾊的润滑脂寿命，延长加脂周期并有节能潜⼒。

Mobiltemp SHC 系列润滑油在全世界许多⾏业中已成为许多⽤户的⾸选产品，因应⽤温度范围⼴及总体性能出⾊⽽享有很⾼的声誉。

特性与优点应⽤范围规格与认可Mobiltemp SHC 系列符合以下⾏业规格：32100460SpecialDIN 51825: (2004-06)KPHC1-2K-50典型性质Mobiltemp SHC Series 32100460SpecialNLGI粘度等级1.521增稠剂类型粘⼟粘⼟粘⼟颜⾊，⽬视红⾊浅褐灰⾊针⼊度，⼯作后，25°C,ASTM D 217315280325滴点，°C,ASTM D2265260+260+260+油粘度，ASTM D445cSt @ 40°C32100460四球测试/磨损，ASTM D2266, 伤痕，mm0.70.40.4四球测试/烧结，ASTM D200+200+250+2596, 负荷，KgMobil SHC 油品和润滑脂的品牌在全世界因创新和性能超卓⽽得到公认及好评。

埃克森美孚Mobil Delvac极限服役润滑脂 MSDS说明书

Page 1 of 8______________________________________________________________________________________________________________________ MATERIAL SAFETY DATA SHEETPRODUCTProduct Name: MOBIL DELVAC XTREME SERVICE GREASEProduct Description:Base Oil and AdditivesProduct Code: 2015A020F010, 530089-00, 97M078Intended Use: GreaseCOMPANY IDENTIFICATIONSupplier: EXXON MOBIL CORPORATION3225 GALLOWS RD.FAIRFAX, VA. 22037 USA24 Hour Health Emergency 609-737-4411Transportation Emergency Phone 800-424-9300ExxonMobil Transportation No. 281-834-3296MSDS Requests 713-613-3661Product Technical Information 800-662-4525, 800-947-9147MSDS Internet Address , * All concentrations are percent by weight unless material is a gas. Gas concentrations are in percent by volume.This material is not considered to be hazardous according to regulatory guidelines (see (M)SDS Section 15). POTENTIAL HEALTH EFFECTSLow order of toxicity. Excessive exposure may result in eye, skin, or respiratory irritation. High-pressure injection under skin may cause serious damage.NFPA Hazard ID:Health: 0 Flammability: 1 Reactivity: 0HMIS Hazard ID:Health: 0 Flammability: 1 Reactivity: 0NOTE: This material should not be used for any other purpose than the intended use in Section 1 without expert advice. Health studies have shown that chemical exposure may cause potential human health risks which may vary from person to person.Page 2 of 8______________________________________________________________________________________________________________________ INHALATIONUnder normal conditions of intended use, this material is not expected to be an inhalation hazard.SKIN CONTACTWash contact areas with soap and water. If product is injected into or under the skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately bya physician as a surgical emergency. Even though initial symptoms from high pressure injection may beminimal or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent of injury.EYE CONTACTFlush thoroughly with water. If irritation occurs, get medical assistance.INGESTIONFirst aid is normally not required. Seek medical attention if discomfort occurs.EXTINGUISHING MEDIAAppropriate Extinguishing Media: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.Inappropriate Extinguishing Media: Straight Streams of WaterFIRE FIGHTINGFire Fighting Instructions: Evacuate area. Prevent runoff from fire control or dilution from entering streams, sewers, or drinking water supply. Firefighters should use standard protective equipment and in enclosedspaces, self-contained breathing apparatus (SCBA). Use water spray to cool fire exposed surfaces and toprotect personnel.Hazardous Combustion Products: Aldehydes, Smoke, Fume, Sulfur oxides, Incomplete combustionproducts, Oxides of carbonFLAMMABILITY PROPERTIESFlash Point [Method]: >204C (400F) [ EST. FOR OIL, ASTM D-92 (COC)]Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/DAutoignition Temperature: N/DNOTIFICATION PROCEDURESIn the event of a spill or accidental release, notify relevant authorities in accordance with all applicableregulations. U.S. regulations require reporting releases of this material to the environment which exceed thereportable quantity or oil spills which could reach any waterway including intermittent dry creeks. The National Response Center can be reached at (800)424-8802.Page 3 of 8______________________________________________________________________________________________________________________ SPILL MANAGEMENTLand Spill: Scrape up spilled material with shovels into a suitable container for recycle or disposal.Water Spill: Stop leak if you can do it without risk. Confine the spill immediately with booms. Warn other shipping. Skim from surface.Water spill and land spill recommendations are based on the most likely spill scenario for this material;however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and speed may greatly influence the appropriate action to be taken. For this reason, local experts should be consulted. Note: Local regulations may prescribe or limit action to be taken.ENVIRONMENTAL PRECAUTIONSPrevent entry into waterways, sewers, basements or confined areas.HANDLINGPrevent small spills and leakage to avoid slip hazard.Static Accumulator: This material is not a static accumulator.STORAGEDo not store in open or unlabelled containers.EXPOSURE LIMIT VALUESNOTE: Limits/standards shown for guidance only. Follow applicable regulations.ENGINEERING CONTROLSThe level of protection and types of controls necessary will vary depending upon potential exposure conditions.Control measures to consider:No special requirements under ordinary conditions of use and with adequate ventilation. PERSONAL PROTECTIONPersonal protective equipment selections vary based on potential exposure conditions such as applications,handling practices, concentration and ventilation. Information on the selection of protective equipment for use with this material, as provided below, is based upon intended, normal usage.Respiratory Protection: If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect worker health, an approved respirator may be appropriate. Respiratorselection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types of respirators to be considered for this material include:No protection is ordinarily required under normal conditions of use and with adequate ventilation.Page 4 of 8______________________________________________________________________________________________________________________ For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode.Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate,gas/vapor warning properties are poor, or if air purifying filter capacity/rating may be exceeded.Hand Protection: Any specific glove information provided is based on published literature and glovemanufacturer data. Work conditions can greatly effect glove durability; inspect and replace worn or damaged gloves. The types of gloves to be considered for this material include:No protection is ordinarily required under normal conditions of use.Eye Protection: If contact is likely, safety glasses with side shields are recommended.Skin and Body Protection: Any specific clothing information provided is based on published literature or manufacturer data. The types of clothing to be considered for this material include:No skin protection is ordinarily required under normal conditions of use. In accordance with goodindustrial hygiene practices, precautions should be taken to avoid skin contact.Specific Hygiene Measures: Always observe good personal hygiene measures, such as washing afterhandling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned.Practice good housekeeping.ENVIRONMENTAL CONTROLSSee Sections 6, 7, 12, 13.Typical physical and chemical properties are given below. Consult the Supplier in Section 1 for additional data.GENERAL INFORMATIONPhysical State: SolidForm: Semi-fluidColor: OrangeOdor: CharacteristicOdor Threshold: N/DIMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATIONRelative Density (at 15 C ): 0.908Flash Point [Method]: >204C (400F) [ EST. FOR OIL, ASTM D-92 (COC)]Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/DAutoignition Temperature: N/DBoiling Point / Range: > 316C (600F)Vapor Density (Air = 1): N/DVapor Pressure: < 0.013 kPa (0.1 mm Hg) at 20 CEvaporation Rate (n-butyl acetate = 1): N/DpH: N/ALog Pow (n-Octanol/Water Partition Coefficient): > 3.5Solubility in Water: NegligibleViscosity: 320 cSt (320 mm2/sec ) at 40 COxidizing Properties:See Sections 3, 15, 16.Page 5 of 8______________________________________________________________________________________________________________________ OTHER INFORMATIONFreezing Point: N/DMelting Point: 260°C (500°F)DMSO Extract (mineral oil only), IP-346: < 3 %wtNOTE: Most physical properties above are for the oil component in the material.STABILITY: Material is stable under normal conditions.CONDITIONS TO AVOID: Excessive heat. High energy sources of ignition.MATERIALS TO AVOID: Strong oxidizersHAZARDOUS DECOMPOSITION PRODUCTS: Material does not decompose at ambient temperatures. HAZARDOUS POLYMERIZATION: Will not occur.CHRONIC/OTHER EFFECTSContains:Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346, Modified Ames test, and/or other screening tests. Dermal and inhalation studies showed minimal effects; lungnon-specific infiltration of immune cells, oil deposition and minimal granuloma formation. Not sensitizing in test animals.Additional information is available by request.Page 6 of 8______________________________________________________________________________________________________________________ The following ingredients are cited on the lists below:None.--REGULATORY LISTS SEARCHED--1 = NTP CARC 3 = IARC 1 5 = IARC 2B2 = NTP SUS 4 = IARC 2A 6 = OSHA CARCThe information given is based on data available for the material, the components of the material, and similar materials. ECOTOXICITYMaterial -- Not expected to be harmful to aquatic organisms.MOBILITYBase oil component -- Low solubility and floats and is expected to migrate from water to the land.Expected to partition to sediment and wastewater solids.PERSISTENCE AND DEGRADABILITYBiodegradation:Base oil component -- Expected to be inherently biodegradableBIOACCUMULATION POTENTIALBase oil component -- Has the potential to bioaccumulate, however metabolism or physical properties may reduce the bioconcentration or limit bioavailability.Disposal recommendations based on material as supplied. Disposal must be in accordance with current applicable laws and regulations, and material characteristics at time of disposal.DISPOSAL RECOMMENDATIONSProduct is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervisedincineration at very high temperatures to prevent formation of undesirable combustion products. REGULATORY DISPOSAL INFORMATIONRCRA Information: The unused product, in our opinion, is not specifically listed by the EPA as a hazardous waste (40 CFR, Part 261D), nor is it formulated to contain materials which are listed as hazardous wastes. It does not exhibit the hazardous characteristics of ignitability, corrositivity or reactivity and is not formulated with contaminants as determined by the Toxicity Characteristic Leaching Procedure (TCLP). However, usedproduct may be regulated.Empty Container Warning PRECAUTIONARY LABEL TEXT: Empty containers may retain residue and can be dangerous. DO NOT PRESSURIZE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION; THEY MAY EXPLODE AND CAUSE INJURY OR DEATH. Do not attempt to refill or clean container since residue is difficult to remove. Empty drums should be completely drained, properly bunged and promptly returned to a drumPage 7 of 8______________________________________________________________________________________________________________________ reconditioner. All containers should be disposed of in an environmentally safe manner and in accordance with governmental regulations.LAND (DOT) : Not Regulated for Land TransportLAND (TDG) : Not Regulated for Land TransportSEA (IMDG) : Not Regulated for Sea Transport according to IMDG-CodeAIR (IATA) : Not Regulated for Air TransportOSHA HAZARD COMMUNICATION STANDARD: When used for its intended purposes, this material is not classified as hazardous in accordance with OSHA 29 CFR 1910.1200.NATIONAL CHEMICAL INVENTORY LISTING: TSCAEPCRA:This material contains no extremely hazardous substances.SARA (311/312) REPORTABLE HAZARD CATEGORIES: None.--REGULATORY LISTS SEARCHED--1 = ACGIH ALL 6 = TSCA 5a2 11 = CA P65 REPRO 16 = MN RTK2 = ACGIH A1 7 = TSCA 5e 12 = CA RTK 17 = NJ RTK3 = ACGIH A2 8 = TSCA 6 13 = IL RTK 18 = PA RTK4 = OSHA Z 9 = TSCA 12b 14 = LA RTK 19 = RI RTK5 = TSCA 4 10 = CA P65 CARC 15 = MI 293Code key: CARC=Carcinogen; REPRO=ReproductivePage 8 of 8______________________________________________________________________________________________________________________ * EPA recently added new chemical substances to its TSCA Section 4 test rules. Please contact the supplier to confirm whether the ingredients in this product currently appear on a TSCA 4 or TSCA 12b list.THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:No revision information is available.----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------The information and recommendations contained herein are, to the best of ExxonMobil's knowledge and belief, accurate and reliable as of the date issued. You can contact ExxonMobil to insure that this document is the most current available from ExxonMobil. The information and recommendations are offered for the user's consideration and examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to handlers and users. Alteration of this document is strictly prohibited. Except to the extent required by law,re-publication or retransmission of this document, in whole or in part, is not permitted. The term, "ExxonMobil" is used for convenience, and may include any one or more of ExxonMobil Chemical Company, Exxon Mobil Corporation, or any affiliates in which they directly or indirectly hold any interest.----------------------------------------------------------------------------------------------------------------------------------------------------- Internal Use OnlyMHC: 0, 0, 0, 0, 0, 0 PPEC: ADGN: 2006067XUS (553320)----------------------------------------------------------------------------------------------------------------------------------------------------- Copyright 2002 Exxon Mobil Corporation, All rights reserved。

美孚SHC齿轮油Mobil SHC630重负荷齿轮油

深圳市华莱斯润滑油贸易有限公司经过努力与Mobil(美国美孚润滑油)、Shell(荷兰壳牌润滑油)、Total(法国道达尔润滑油)、Kluber（德国克鲁勃润滑油）、Castrol（英国嘉实多润滑油）、BP(英国BP润滑油)、Caltex(美国加德士润滑油) 、Fuchs(德国福斯润滑油)等国际知名企业的战略合作伙伴或一级代理分销商精诚合作。

美孚SHC 630系列润滑油是性能卓越的齿轮与轴承油的设备保护，油品寿命及无故障操作，能够提高客户的生产力。

这些油是设计科学配方，基础油的一个固有的高粘度指数和一个独特的，专有的添加剂系统，合成产品天意出色的性能在极端的服务应用程序在高和低的温度下应，远远超出矿物油的能力。

这些产品具有耐机械剪切，即使在负荷极重的齿轮和受高剪切作用力的轴承，美孚SHC 600系列产品中使用的基础油，具有出色的响应，特别是在高温下抗氧化添加剂的的TION结果在优越的抗氧化。

在添加剂组合以优异的抗锈蚀和腐蚀，很好的抗磨，抗乳化性，泡沫控制和空气释放性，以及多金属相容性。

美孚SHC 600系列润滑油被推荐用于在各种各样的齿轮和轴承的应用程序那里温度过高或过低将遇到的是或的工作温度应油体温度应顷，具体应用包括：∙充满生活的齿轮箱，特别是高比率/低效率的蜗轮蜗杆传动装置∙远程位于变速箱，油变化是困难的∙低温应用滑雪缆车，可避免季节性换油∙调音台轧辊轴承与辊颈轴承高温战神遇到∙塑料日历∙严重的离心分离机的应用程序，海洋离心机∙铁路A / C牵引传动∙美孚SHC 625 * 627，629和630是适用于注油旋转螺杆式压缩机，压缩天然气，现场集气，二氧化碳及其他在天然气工业中使用的工艺气体美孚SHC600系列624625（1）626627629630632634636639ISO粘度等级32 46 68 千美孚SHC600系列624625（1）626627629630632634636639 100 150 220 320 460 680粘度，ASTM D 445CST @40ºC31.46.66.97.149 222 320 454 652 968CST @100ºC5.8 7.7 10.3 13.719.25.735.46.561.278.5粘度指数，ASTM D2270 133136144 144 144 147 154 161 163 159倾点，ºC，ASTM D 97 -51 -48-48 -45 -45 -42 -40 -40 -39 -33美孚SHC600系列624625（1）626627629630632634636639闪点92ºC，ASTM D 237 242231 228 235 240 236 234 240 23515ºC/15ºC比重，ASTM D 4052，0.850.850.860.860.860.870.870.870.870.87外观方面，视觉橙橙橙橙橙橙橙橙橙。

美孚产品系列

工业润滑油产品
应用
产品系列
阻塞密封油
美孚SHC 600系列、美孚Synturion 6
链条油和窑炉润滑油
美孚合成窑炉润滑油1090、美孚Pyrolube 830,
Socony窑炉输送机润滑油
压缩机油–空气及惰性气体
美孚拉力士1020系列、美孚拉力士800系列、美孚格高系列、美孚SHC 500系列、美孚SHC 600系列、美孚拉力士400系列、美孚DTE Oil 205
冷却剂–金属加工
美孚克特300系列、美孚克特100系列、美孚克特200系列
联轴器润滑油
美孚齿轮油SHC 22M和46M、美孚力富SHC系列、美孚齿轮油600 XP系列3、美孚滑脂XTC、Mobilux EP 111
切削液–金属加工
美孚美特400系列、美孚美特760系列、Vacmul系列
电动机润滑脂
Mobilith SHC系列、美孚Polyrex EM
其它产品
应用
产品系列
汽车底盘及轴承润滑脂
美孚1号合成润滑脂、美孚Infinitec 152、Ronex MP
商用车底盘及轴承润滑脂
美孚黑霸王极限润滑脂、美孚Centaur Moly、美孚滑脂HT系列
发动机油–汽车
美孚1号系列
发动机油–柴油
美孚黑霸王1系列、美孚黑霸王1300系列、美孚黑霸王1600系列
润滑脂
美孚力富SHC系列、Mobiltemp SHC系列、美孚力富SHC PM系列、美孚齿轮油EAL系列、美孚齿轮油XHP系列、美孚宝力达EM、美孚宝力达EP2、Mobiltemp系列、Mobilux EP系列
传热油
Mobiltherm 600系列
液压油
美孚EAL Envirosyn H系列、美孚SHC 500系列、美孚Pyrogard 53、美孚Pyrotech HFD 46、美孚DTE 10M系列、美孚DTE 20系列、美孚DTE FM系列、美孚DTE Oil命名系列、美孚EAL 224H、美孚Pyrogard D、美孚Nyvac FR 200D润滑液

美孚与壳牌产品对比

DTE 20系列
DTE 21(10黏度) Tellus S2 V 15
DTE 22
Tellus S2 M 22
DTE 24
Tellus S2 M 32
DTE 25
Tellus S2 M 46
DTE 26
Tellus S2 M 68
DTE 27
Tellus S2 M 100
DTE 10M 系列
DTE 11M
Omala F 320
XMP 460
Omala F 460
XMP 680
美孚已取消
齿轮油 600 系列(已改名600 XP系列)
mobilgear 626 Omala S2 G 68
mobilgear 627 Omala S2 G 100
mobilgear 629 Omala S2 G 150
mobilgear 630 Omala S2 G 220
度)
Rarus 826
Corena S4 R 68
Rarus 827
Corena S4 P 100
Rarus 829(150黏无
度)
拉力士 SHC 1020
空气压缩机油 Rarus SHC1024 Rarus SHC1025 Rarus SHC1026 拉力士400系列
Corena S4 R 32 Corena S4 R 46 Corena S4 R 68
产品类别液压油
齿轮油
美孚与壳牌产品对比
美孚Mobil
壳牌Shell
DTE 超凡系列
DTE Excel 22 无,这个黏度等级少用到
DTE Excel 32 Tellus S3 M 32
DTE Excel 46 Tellus S3 M 46

美孚油品参数表

下一代Mobil SHC 600 系列624 625 626 627 629 630 632 634 636 639 ISO 粘度等级32 46 68 100 150 220 320 460 680 1000粘度，ASTM D 445cSt @ 40º C 32 46 68 100 150 220 320 460 680 1000 cSt @ 100º C 6.3 8.5 11.6 15.3 21.1 28.5 38.5 50.7 69.0 98.8粘度指数，ASTM D2270 148 161 165 162 166 169 172 174 181 184倾点，ºC，ASTM D5950 -57 -54 -51 -45 -42 -42 -42 -39 -39 -33闪点，ºC，ASTM D 92 236 225 225 235 220 220 225 228 225 222密度@ 15°C (60°F) (g/cc) ASTM D4052 0.85 0.85 0.86 0.86 0.86 0.87 0.87 0.87 0.87 0.87肉眼外观橙色橙色橙色橙色橙色橙色橙色橙色橙色橙色TOST，ASTM D 943 mod，小时数10,000+ 10,000+ 10,000+ 10,000+ 10,000+ 10,000+ 10,000+ 10,000+ 10,000+ 10,000+ RPVOT，ASTM D 2722，分钟2500 2500 2500 2500 2500 2500 2500 2500 2500 2500抗锈蚀试验，ASTM D665B，合成海水合格合格合格合格合格合格合格合格合格合格分水性，ASTMD1401，54º C 时达到37 ml 水的时间，分钟(min)10 15 15 - - - - - - -分水性，ASTMD1401，82º C 时达到37 ml 水的时间，分钟(min)- - - 15 20 20 20 20 20 25 美孚齿轮油参照表下一代Mobil SHC 600 系列624 625 626 627 629 630 632 634 636 639铜片腐蚀试验，ASTM D130，24 hrs @ 121º C1B 1B 1B 1B 1B 1B 1B 1B 1B 1B泡沫试验，ASTM D892，顺序I、II、III，倾向性/稳定性，ml/ml 15/0,20/0,25/0 10/0,30/0,10/010/0,20/0,10/00/0,10/0,0/00/0,0/0,0/0/0,10/0,0/00/0,0/0,0/00/0,0/0,0/00/0,0/0,0/00/0,0/0,0/0FZG 齿轮胶合试验，A/8.3/90，ISO 14635-1 (mod)，失效级数11 12 12 12 13 13+ 13+ 13+ 13+ 13+FAG FE8 轴承磨损试验7.5/80-80((DIN 51819-3)滚轴磨损(mg)- - - 2 2 2 2美孚抗磨液压油参照表2018-04-24整理。

油品编码参照表

乌鲁木齐荣立商贸有限公司
（美孚、爱克玛润滑油授权代理商）
地址：乌鲁木齐经济技术开发区厦门路63号电话：3717624 3713281 传真：3732691致：新疆中泰
化学（集团）
尊敬的殷勇先生：您好！
备注：此价格为含17%的增值税与到现场的的价格。

因2010年以来原油价格的持续上涨，导致在2010年至2011年美孚润滑油价格几次上调，我公司为了能够更好地提供优质的产品及润滑服务，经慎重考虑对今年的润滑油产品价格进行调整，以利于共同发展，望贵公司予以支持和理解。

今后我公司会一如既往地向贵公司提供优质的产品，优良的服务。

我们衷心的希望能得到贵公司的理解和信任！
乌鲁木齐荣立商贸有限公司
2012年4月20日。

齿轮油安全技术说明书(MSDS)

若遇高热，容器内压增大，有开裂和爆炸的危险。

有害燃烧产物： 1.可能分解出一氧化碳及二氧化碳气体。

2.烟气。

3.乙醛,硫氧化物。

灭火方法：使用消防水雾、泡沫、干化学制剂(干粉)或者二氧化碳(CO2)灭火，不能用水灭火。

消防说明疏散该地区。

?防止控制火灾或稀释的流出液流入河川、下水道或饮水源。

?消防员应使用标准防护设备,在密闭空间需使用自给式呼吸器(SCBA)。

?用喷水的方式使暴露于火灾的表面降温并保护工作人员。

切断火源。

建议应急处理人员戴自给正压式呼吸器，穿一般作业工作服。

尽储存注意事项： 1.使用适当设计及保养的机械通风系统,如整体换气装置或局部排气装置。

2.以局部排气装置及必要的制程隔离以控制雾滴及蒸气量。

3.供给充分新鲜空气以补充排气系统抽出的空气。

4.可能需要处理发散的废气以免污染环境。

5.置于室内环境,保持油品密封，不可与易燃、易爆化学品摆在一起。

6.不可存放于开口或者无标识容器中。

静电集电物:?? 本产品蓄积静电。

第八部分：接触控制/个体防护监测方法：密闭操作，注意通风。

工程控制：防护级别和所需的控制措施的种类根据潜在的接触条件不同而不同。

可供选择的控制措施包括:?在通常使用环境和充分通风条件下没有特殊要求。

当空气中浓度超标时，建议佩戴自吸过滤式防毒面具（半面罩）。

紧急事态抢救或撤离时，应该佩戴空气呼吸器。

个人防护：选择个人防护设备因可能的接触条件,如应用领域、处理工作、浓度和通风等而异。

美孚Mobil润滑油齿轮油新旧型号及与其他品牌型号对照

加德士 Caltex Meropa68 Meropa100 Meropa150 Meropa220 Meropa320 Meropa460 Meropa680 壳牌公司 Shell Omala68 Omala100 Omala150 Omala220 Omala320
英国石油 BP Energol GR XP68 Energol GR XP100 Energol GR XP150 Energol GR XP220 Energol GR XP320 Energol GR XP460 Energol GR XP680 埃克森 Exxon Spartan EP68 Spartan EP100 Spartan EP150 Spartan EP220 Spartan EP320
Mobil 600XP680 Mobil 600XP460 Mobil 600 XP320 Mobil 600XP220 Mobil 600XP150 Mobil 600XP100 Mobil 600XP68
L-CKD680 L-CKD320 L-CKD220 L-CKD100
其他国内外重负荷工业齿轮油产品牌号对照表
美孚公司 Mobil 埃克森 Energol HLP100 壳牌公司 Shell Tellus-33 Exxon DTE-26 Bando HD68 Mobilgear626 Energol HLP150 Mobilgear627 BP Omala68 DTE-27 Omala100 Mobil Spartan Bando HD100 Tellus-41 EP68 Spartan EP100 Shell Caltex
中石化长城（得威） L-CKD150 L-CKC68 L-CKD220 L-CKC100 L-CKD320 L-CKC150 L-CKD460 L-CKC220 L-CKD680