朗讯CDMA项目网优数据操作手册--参数具体位置及修改办法

朗讯CDMA网优数据制作（操作手册）2010年1月1日一、cgsa第6页频点设置 (9)此表由MSC开局时总体规划 (9)二、1X一载波网优数据制作 (9)cell2第1页（日照边界纵为10，核心纵为8） (9)cell2第11页（打开六方软切换功能） (10)ceqface3g第1页（2G/3G承载比例） (10)ceqface3g第2页(3G1x是否共享） (11)ceqface3g第3页（载波语音/数据话务分担） (11)ceqface3g第8页(关闭RC4功能） (12)ceqface第8页(设置PN及切换参数） (12)ceqface第14页 (13)ceqface第16页1321值为空 (14)ceqface第24页（导频数字增益值，查表配套设置） (14)普通内部小区邻区设置 (15)朗讯MSC边界小区邻区设置 (15)厂商间基站的硬切换设置 (16)fci第15页(邻区设置）（其他厂商MSC边界小区硬切换） (16)ivc第1页(邻区设置）（其他厂商MSC边界小区硬切换） (16)二、1X二载波内部小区网优数据制作 (17)cell2第1页（日照边界纵为10,核心纵为8） (17)cell2第11页（打开六方软切换功能） (18)ceqface3g第1页（2G/3G承载比例） (18)ceqface3g第2页(3G1x是否共享） (19)ceqface3g第3页（载波语音/数据话务分担） (19)ceqface第8页(设置PN及切换参数） (20)ceqface第14页（载频间话务分担设置及边界扇区的切换设置） (20)ceqface第16页（二载波边界扇区设置1321项值为2,非边界扇区值为空） (21)三、RC4功能设置 (22)ceqface3g第8页(关闭RC4功能） (22)ceqface3g第8页(打开RC4功能） (22)四、导频数字增益值 (23)五、扇区载波功率及衰减设置可调整个别基站的覆盖范围 (24)(需要与ceqface24页导频数字增益结合吗，怎么结合？) (24)六、设置伪导频 (24)（基站数据负责）确保cgsa表格中存在需要使用的频点 (24)（基站数据负责）cell2表格中确定新增载频要用的交换资源 (25)（基站数据负责）Btseqp表格第14页设置伪导频共享的CCU (25)（基站初设，优化更改）Btseqp表格第21/22/23页设置伪导频的频点参数 (26)ceqface第29页(设置伪导频时用） (26)ivc第1页(邻区设置）（其他厂商MSC边界小区硬切换） (27)厂商间基站的硬切换设置 (27)七、载波专用于数据或语音 (28)八、OMCRAN中的优化数据制作 .................................................................错误！未定义书签。

扇区PN值修改......................................................................................错误！未定义书签。

DO邻区添加（不超过20条） ...............................................................错误！未定义书签。

扇区经纬度设置（一般不用设）.............................................................错误！未定义书签。

注意本文为了规范朗讯CDMA项目网优OMP数据操作编写，文件所引用数据为JNOMP4（IP：10.253.210.2）现网数据。

文中尚有不准确之处，敬请指正。

王本清 2010年1月1日基站数据制作站号、ZONEID设置，边界纵10，核心纵8CDMANetworks SERIES 2 CELL (cell2) Screen 1 of 40Cell Site Number............................ *1) 100ACC Location Area ID........................ +2) ____DCCH Virtual Mobile Location Area........... +3) ____CDMA Registration Zone ID................... +4) 8VZID/CID Cell ID............................ 5) ____Cellular Geographic Service Area............ 6) 7Switch Identification....................... @7) 10Virtual Switch Identification............... 8) __CDMA Switch Identification.................. 9) 10CDMA Virtual Switch Identification.......... 10) __Cell Site Status............................ 12) eLocation Equipped Antenna Faces............. 13) 0Wait for Overhead Message................... 14) yPerform Pre-setup on Traffic Channel........ 15) yTraffic Channel Holding Timer(sec).......... 16) 15TrFO/RTO on FPS Enabled..................... 17) nRNC ID...................................... 18) __Enter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________基站版本设置CDMANetworks SERIES 2 CELL (cell2) Screen 4 of 40 Cell 100Cell Site Dial-Up Number - Area Code................ 101)___- Office Code.............. 102)___- Station Number........... 103)____Cell Site Extended Dial-Up Number................... 104)______________ Cell Generic - Version Name......................... 105)F3113DDGA- R5 Compatible........................ 106)yFlexent Cell Site RCS Revision Number............... 107)0Flexent Software - Revision Number................. +108)0- Diagnostic Generic............... 109)D3113DDGABTS Name ........................................... 111)____________Priority Paging Control ........................... +112)_22144/22145 Assert................................. +115)___Mobile Station Reject Assert....................... +116)onRadio Initialization Debug Control................. +117)offControl for Paging Channel Occupancy Improvement.... 118)offInitial Default Noise Floor........................ @119)SImproved Noise Floor Adaptation Control Enable..... @120)nEnter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________BHS资源设置CDMANetworks SERIES 2 CELL (cell2) Screen 31 of 40Cell 100CDMA Cell Site For IP Backhaul Information ONLY:480)CDMA Carrier:Row Common Service Switching Packet BackhaulNum Carrier Option Class Module Switching Unit Server481) 482) 483) 484)[1] 1 BOTH 2 0 2[2] 2 BOTH 2 0 2[3] 3 _____ ___ _ __[4] 4 _____ ___ _ __[5] 5 _____ ___ _ __[6] 6 _____ ___ _ __[7] 7 _____ ___ _ __[8] 8 _____ ___ _ __[9] 9 _____ ___ _ __[10] 10 _____ ___ _ __Enter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________基站AP设置CDMANetworks CDMA MODULAR CELL EQUIPAGE (cmodeqp) Screen 1 of 14Cell Site Number.................................. *1) 100Cell Configuration................................ 2) 1bts_modPrimary Application Processor Number.............. 3) 2Alternate Application Processor Number............ 4) 1CDM Out of Service Limit (%)...................... +5) ___Functional Test Intervals:- CDMA Antenna (sec)........................... 6) 0- CDMA Overhead Channels (min)................. +7) ____- CDMA Traffic Path (min)...................... +8) ____- CDMA Pilot Level (min)....................... +9) ____Pilot Level Tolerance (db)....................... +10) ___CDMA Test Radio Module Status.................... 11) uEnter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________功放设置CDMANetworks CDMA MODULAR CELL EQUIPAGE (cmodeqp) Screen 7 of 14 115) MCA Equipage:MCA MCA Phy Tx Amp TxAmp TxAmp RevPwr MCPA SII MCPA PwrNum Type Ant Numbers Asm Spare Thresh PwrUsage Offset 116) 117) 118)119)120)121)122)123)124) @125) 126) 127) 128)[1] 1 chpamhe 1 1 __ __ __ __ __ 1 n ____ ___ ___[2] 2 chpamhe 2 4 __ __ __ __ __ 1 n ____ ___ ___[3] 3 chpamhe 3 7 __ __ __ __ __ 1 n ____ ___ ___[4] 4 _______ _ __ __ __ __ __ __ _ _ ____ ___ ___[5] 5 _______ _ __ __ __ __ __ __ _ _ ____ ___ ___[6] 6 _______ _ __ __ __ __ __ __ _ _ ____ ___ ___[7] 7 _______ _ __ __ __ __ __ __ _ _ ____ ___ ___[8] 8 _______ _ __ __ __ __ __ __ _ _ ____ ___ ___[9] 9 _______ _ __ __ __ __ __ __ _ _ ____ ___ ___[10] 10 _______ _ __ __ __ __ __ __ _ _ ____ ___ ___[11] 11 _______ _ __ __ __ __ __ __ _ _ ____ ___ ___[12] 12 _______ _ __ __ __ __ __ __ _ _ ____ ___ ___ Enter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________Ceqface时延设置CDMANetworks CELL EQUIPAGE FACE (ceqface) Screen 18 of 47 Cell 100 Face 1@1484) CDMA Antenna Propagation Delay (microseconds)Transmit Receive Transmit Receive Transmit Receive Carriers Antenna Antenna Carriers Antenna Antenna Carriers Antenna Antenna 1485) 1486) 1490) 1491) 1495) 1496)[1] 035.2 022.0 [12] 022.5 014.0 [23] 022.5 014.0[2] 035.2 022.0 [13] 022.5 014.0 [24] 022.5 014.0[3] 035.2 022.0 [14] 022.5 014.0 [25] 022.5 014.0[4] 022.5 014.0 [15] 022.5 014.0 [26] 022.5 014.0[5] 022.5 014.0 [16] 022.5 014.0 [27] 022.5 014.0[6] 022.5 014.0 [17] 022.5 014.0 [28] 022.5 014.0[7] 022.5 014.0 [18] 022.5 014.0 [29] 022.5 014.0[8] 022.5 014.0 [19] 022.5 014.0 [30] 022.5 014.0[9] 022.5 014.0 [20] 022.5 014.0 [31] 022.5 014.0[10] 022.5 014.0 [21] 022.5 014.0 [32] 022.5 014.0[11] 022.5 014.0 [22] 022.5 014.0 [33] 022.5 014.0Warning: Antenna Propagation Delay values on this form are applicable for CDMA carriers only. EVDO carrier Antenna Propagation Delay values aremanaged on the EMS GUI, "Sector" (General Attributes) page.Enter Review, Validate, screen#, or Print:________________________________________________________________________________ 背版号设置CDMANetworks CDMA OneBTS MODCELL ASSEMBLAGE EQUIPAGE (btseqp) Screen 1 of 27Cell Site Number............................. *1) 100Assemblage Number............................ *2) 1Backplane Serial Number...................... 3) 08TG09067648Spare CRC Controller Type ................... @4) ______Channel Elements OOS Limits: Minor.......... +5) ___Major.......... +6) ___IA Enabled PAF 1............................. @7) nIA Enabled PAF 2............................. @8) nIA Enabled PAF 3............................. @9) nEnter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________1X第二根2MCDMANetworks CDMA OneBTS MODCELL ASSEMBLAGE EQUIPAGE (btseqp) Screen 2 of 27 Cell 100 Assemblage 1 CRC/CDM 1CRC Status ................... 19) e 28) CDMA Digital Module DS1 Info.: CRC Controller Type ......... @20) URC Status Type Data RateSpare CRC Status ............. 21) u Num 29) 31) 32)Backhaul Mode ............... @22) IP [1] e ___ __Transmission Facility Type ... 23) l [2] e ___ __Flexent Software Rev Number. @+24) __ [3] u ___ __Signaling Link Width ......... 25) _ [4] u ___ __CRC Overload Control (%) .... +26) __ [5] u ___ __CRC Technology Type ......... @27) 1X [6] u ___ __[7] u ___ __[8] u ___ __Enter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________DO数据添加CDMANetworks CDMA OneBTS MODCELL ASSEMBLAGE EQUIPAGE (btseqp) Screen 6 of 27 Cell 100 Assemblage 1 CRC/CDM 2CRC Status ................... 139)e 148) CDMA Digital Module DS1 Info.: CRC Controller Type ......... @140)URC-II Status Type Data RateSpare CRC Status ............. 141)u Num 149) 151) 152)Backhaul Mode ............... @142)SH [1] e ___ __Transmission Facility Type ... 143)l [2] e ___ __Flexent Software Rev Number. @+144)__ [3] e ___ __Signaling Link Width ......... 145)_ [4] u ___ __CRC Overload Control (%) .... +146)__ [5] u ___ __CRC Technology Type ......... @147)DO [6] u ___ __[7] u ___ __[8] u ___ __Enter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________DO数据添加CDMANetworks CDMA OneBTS MODCELL ASSEMBLAGE EQUIPAGE (btseqp) Screen 8 of 27 Cell 100 Assemblage 1 CRC/CDM 2Frame Relay (FR) Specific Parameters:Digital Module Signaling Link Information for Connections at the CDM:CRC Primary: DS1 213)_ DS0 214)__CRC Alternate: DS1 215)_ DS0 216)__CRC VIM: DS1 @217)_ DS0 @218)__AP Signaling Link Information for Connections at the AP:Primary AP: DS1 219)_ DS0 220)__ Notes 221)________________Alternate AP: DS1 222)_ DS0 223)__ Notes 224)________________1xEV-DO Specific Parameters:DO LIU Processor Overload Control...................... 225)offOverload Control Threshold for DO LIU Processor (%).... 226)80DO EVM Processor Overload Control...................... 227)offOverload Control Threshold for DO EVM Processor (%).... 228)80Physical CRC Providing 1xEV-DO CDM Signaling Link ..... 229)1Enter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________ CMU EVM数据添加(在放开入网前需grows掉)CDMANetworks CDMA OneBTS MODCELL ASSEMBLAGE EQUIPAGE (btseqp) Screen 14 of 27 Cell 100 Assemblage 1379) CDMA Channel Unit (CCU) Information:Row CCU CCU CCU CE CEs CCU @CCU CarriersNum Num Status TechType Max Enabled CRC Block a380) @381) @382) @383) 384) 385)386)387)388)389)390)[ 1] 1 e 1X 128 ___ 1 1 2 __ __ __ __[ 2] 2 u ___ ___ ___ __ __ __ __ __ __ __[ 3] 3 e DO1 ___ ___ 2 4 __ __ __ __ __@CCU Carriers @CCU Carriers @CCU CarriersBlock b for CE Max 256 Block c for CE Max 256 Block d for CE Max 256 391)392)393)394)395)396) 397)398)399)400)401)402) 403)404)405)406)407)408) [ 1] __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ [ 2] __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ [ 3] __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __Enter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________ 扇区MCR参数设置CDMANetworks CDMA OneBTS MODCELL ASSEMBLAGE EQUIPAGE (btseqp) Screen 19 of 27 Cell 100 Assemblage 1567) CBR Equipage:Row CBR CBR CBR CBR CBR TX Port1 TX Port2 Phy B ase Rx Imbl CBR CBR Num Num Stat CRCs CRCs CRCs MCA CLGC MCA CLGC Ant Class Thrshld Type Ptnr 568) 569) 570) 571) 572) @573) 574) @575) 576) @577) 578) @579) @580)[1] 1 e 1 2 __ 1 1 __ _ 1 IS95 10.0 15MHz _[2] 2 e 1 2 __ 2 1 __ _ 2 IS95 10.0 15MHz _[3] 3 e 1 2 __ 3 1 __ _ 3 IS95 10.0 15MHz _[4] 4 u __ __ __ __ _ __ _ _ ____ ____ 5MHz _[5] 5 u __ __ __ __ _ __ _ _ ____ ____ 5MHz _[6] 6 u __ __ __ __ _ __ _ _ ____ ____ 5MHz _Enter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________ Btseqp表格第21—23页设置各扇区载波参数CDMANetworks CDMA OneBTS MODCELL ASSEMBLAGE EQUIPAGE (btseqp) Screen 21 of 27 Cell 100 Assemblage 1601) CBR 1 Carrier Equipage:Row Carr Carr Max Pging Acc Max Acc CBR Tx Port BCCH FCCCH REACH Num Carr Chnl Type Pwr Chnls Chnls Chnls Att Num Chnls Chnls Chnls @602) 603) 604) 605) @606) @607) 608) 609) @610) 611) 612) 613)[ 1] 4 37 DO 020.0 1 1 _ 02.0 1 0 0 0[ 2] 2 201 1X 010.0 1 1 _ 05.0 1 0 0 0[ 3] 1 283 1X 020.0 1 1 _ 02.0 1 0 0 0[ 4] __ ____ __ _____ 1 1 _ ____ ____ 0 0 0[ 5] __ ____ __ _____ 1 1 _ ____ ____ 0 0 0[ 6] __ ____ __ _____ 1 1 _ ____ ____ 0 0 0[ 7] __ ____ __ _____ 1 1 _ ____ ____ 0 0 0[ 8] __ ____ __ _____ 1 1 _ ____ ____ 0 0 0[ 9] __ ____ __ _____ 1 1 _ ____ ____ 0 0 0[10] __ ____ __ _____ 1 1 _ ____ ____ 0 0 0[11] __ ____ __ _____ 1 1 _ ____ ____ 0 0 0 Enter Review, Change-insert, Validate, screen#, or Print:网优数据制作一、c gsa第6页频点设置此表由MSC开局时总体规划CDMANetworks CELLULAR GEOGRAPHIC SERVICE AREA (cgsa) Screen 6 of 21WARNING:1. CHANGING THE CHANNEL NUMBER, BANDCLASS, BAND SUBCLASS OR CARRIERTYPE OF AN ACTIVE CARRIER MAY RESULT IN THE TERMINATION OF CALLS.REFER TO THE DATA BASE UPDATE FOR MORE DETAILS (LUCENT-401-610-036).2. THE DO CARRIER IS APPLICABLE ONLY ON THE BTSEQP AND CDMEQP FORMS.+130) CDMA Carrier:Row Common @Chnl @Carr @Band Band Sub Test Carrier 3G Allowed 2G Overlay Num Carrier Number Type Class Class Designation Carrier Carrier[1] 1 283 1X 850 _ _ 3G-allowed n[2] 2 201 1X 850 _ _ 3G-allowed n[3] 3 242 1X 850 _ _ 3G-allowed n[4] 4 37 DO 850 _ _ 3G-allowed n[5] 5 ____ 1X _________ _ _ 3G-allowed n[6] 6 ____ 1X _________ _ _ 3G-allowed n[7] 7 160 1X 850 _ _ 3G-allowed n[8] 8 ____ 1X _________ _ _ 3G-allowed n[9] 9 ____ 1X _________ _ _ 3G-allowed n[10] 10 ____ 1X _________ _ _ 3G-allowed nEnter Update, Change, Validate, screen#, or Print:二、1X一载波网优数据制作________________________________________________________________________________ cell2第1页（日照边界纵为10，核心纵为8）CDMANetworks SERIES 2 CELL (cell2) Screen 1 of 40Cell Site Number............................ *1) 262ACC Location Area ID........................ +2) ____DCCH Virtual Mobile Location Area........... +3) ____CDMA Registration Zone ID................... +4) 8VZID/CID Cell ID............................ 5) ____Cellular Geographic Service Area............ 6) 7Switch Identification....................... @7) 10Virtual Switch Identification............... 8) __CDMA Switch Identification.................. 9) 10CDMA Virtual Switch Identification.......... 10) __Cell Site Status............................ 12) eLocation Equipped Antenna Faces............. 13) 0Wait for Overhead Message................... 14) yPerform Pre-setup on Traffic Channel........ 15) yTraffic Channel Holding Timer(sec).......... 16) 15TrFO/RTO on FPS Enabled..................... 17) nRNC ID...................................... 18) __Enter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________ cell2第11页（打开六方软切换功能）超远程基站需将238第7项设为yCDMANetworks SERIES 2 CELL (cell2) Screen 11 of 40 Cell 262Cell Site Optional Features ( cont. )232) 234) 236) 238)[1] CDMA S2M/S2MM n TDMA CNAP n OFD-CAP y MSINACT TRIG n[2] TDMA TBIA n CDMA 2G CDPD n OFD-PG y TDMA FLCA DA n[3] CTRAF SMS y CDMA 2G IP y TDMA DTX CNI n Reserved n[4] CDMA IFHO TI n CDMA RLPE n TDMA HIER CELLS n ANLG ON TMC n[5] Reserved n OFD-MS y Reserved n Reserved n[6] Reserved n OFD-A y TDMA FLCA LM n TDMA MDCCH n[7] Reserved n CDMA ACO CTRL y CDMA CNAP n CDMA FRANGEXT n[8] Reserved n TDMA DATAPRIV n INTL ROAM y CDMA 3G1XHSPD y[9] MC DS0 NAILUP n COACC SMS y TDMA OTASP 1 n TDMA DDPC n[10] CDMA SHAPCAR n LCR n CDMA ANFX n INTL ROAM MIN n[11] CDMA SCSFT n CDMA MPIFHO y CDMA OTAPA n CDMA BKHAULEE y[12] CDMA PN & UZ n Reserved n CDMA RXANT n CDMA BCST SMS y[13] TDMA OTASP n CDMA PPOPTMT y TDMA GUTS n Reserved n[14] TDMA CKT DATA n CDMA PP 16 y CDMA COLOC n Reserved nEnter Review, Change-insert, Validate, screen#, or Print:________________________________________________________________________________ ceqface3g第1页（2G/3G承载比例）CDMANetworks CELL EQUIPAGE FACE For 3G (ceqface3g) Screen 1 of 193G1X CDMA - VoiceCell Site - Number ...........................................*1) 262- Physical Antenna Face ............................*2) 13G1X Load Preference Delta: Prim.........+3) 40 Alt.......+4)___？7) Carriers Using Alt:1 1 1 1 1 1 1 1 1 12 2 2 2 2 2 2 2 2 23 3 3 31 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _2G Load Preference Delta: Prim.........+72)0 Alt......+73)___76) Carriers Using Alt:1 1 1 1 1 1 1 1 1 12 2 2 2 2 2 2 2 2 23 3 3 31 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Quick Paging Channel Transmit Power Level ................... 141)-3Number of 3G Traffic Channel Preamble ....................... 142)7Enter Review, Validate, screen#, or Print:________________________________________________________________________________ceqface3g第2页(3G1x是否共享）CDMANetworks CELL EQUIPAGE FACE For 3G (ceqface3g) Screen 2 of 19Cell 265 Face 13G1X CDMA Information - VoicePreferred 8K Forward RC: Prim.........+146)3 Alt.......+147)_150) Carriers Using Alt:1 1 1 1 1 1 1 1 1 12 2 2 2 2 2 2 2 2 23 3 3 31 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Allow Sharing 3G1X Carrier: Prim.........+215)y Alt.......+216) ___？（n表示不起作用） 219) Carriers Using Alt:1 1 1 1 1 1 1 1 1 12 2 2 2 2 2 2 2 2 23 3 3 31 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3_ __ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _SMV EVRCBForward Vocoder Mode: +284)_ +286)_Reverse Vocoder Mode: +285)_ +287)_Enter Review, Validate, screen#, or Print:________________________________________________________________________________ceqface3g第3页（载波语音/数据话务分担）CDMANetworks CELL EQUIPAGE FACE For 3G (ceqface3g) Screen 3 of 19Cell 262 Face 13G1X CDMA Information - DataF-SCH Notification Threshold (%) ............................ 291) 50F-SCH Max Rate (kbps) .. 292) 153.6 F-SCH Min Rate (kbps) .. 293) 019.2R-SCH Max Rate (kbps) .. 294) 153.6 R-SCH Min Rate (kbps) .. 295) 019.2Max Num Active Set Pilots for Data Calls ....................+296) _Anchor Hysteresis (dB) ...................................... 297) 1.0Data Relative Strength Threshold (dB) ....................... 298) 2.53G1X Data Load Preference Delta (%): Prim...+299)40 Alt..+300) ___303) Carriers Using Alt:1 1 1 1 1 1 1 1 1 12 2 2 2 2 2 2 2 2 23 3 3 31 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3_ __ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Anchor Monitoring Interval (sec): Prim...+368)2.2 Alt..+369) ___372) Carriers Using Alt:1 1 1 1 1 1 1 1 1 12 2 2 2 2 2 2 2 2 23 3 3 31 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Enter Review, Validate, screen#, or Print:________________________________________________________________________________ ceqface3g第8页(关闭RC4功能）CDMANetworks CELL EQUIPAGE FACE for 3G (ceqface3g) Screen 8 of 19 Cell 262 Face 1CDMA Per Carrier Information1013) 3G1X CDMA per Carrier InformationRow RC4 Enabled RC4 DeterminationNum Carrier Threshold Threshold[1] 1 60 2.0[2] 2 60 2.0[3] 3 60 1.0[4] 4 60 1.0[5] 5 60 1.0[6] 6 60 1.0[7] 7 60 1.0[8] 8 60 1.0[9] 9 60 1.0[10] 10 60 1.0[11] 11 60 1.0Enter Review, Validate, screen#, or Print:________________________________________________________________________________ceqface第8页(设置PN及切换参数）切换参数、搜索窗必要时需做调整CDMANetworks CELL EQUIPAGE FACE (ceqface) Screen 8 of 47Cell 262 Face 1CDMA Information (Non-Power Control):Pilot PN Sequence Offset Index................................ @111)78Pilot PN Sequence Offset Index Increment Multiplier ........... 112)1Pilot Detection Threshold (dB)................................. 113)-13.0Pilot Drop Threshold (dB)...................................... 114)-15.0Active Set vs Candidate Set Comparison Thresh (dB)............. 115)2.5Active Set vs Candidate Set Comparison Thresh for Analog (dB).. 116)2.5Drop Timer..................................................... 117)3Search Window Size: Active Set and Candidate Set............ 118) 7Neighbor Set............................ 119) 9Remaining Set........................... 120) 0Cell (microseconds)..................... 121) 32Sector Size (miles)......................................... @+122) ____Transmit Delay (microseconds)................................ @123) 0Analog Handdown Physical Ant Face at Serving Sector........... 124) _Analog Equivalent Server Group at Serving Sector.............. 125) _Base Station ID............................................... 126) _____Enforced True Sector Size..................................... 127) nEnter Review, Validate, screen#, or Print:________________________________________________________________________________ ceqface第14页CDMANetworks CELL EQUIPAGE FACE (ceqface) Screen 14 of 47 Cell 262 Face 1CDMA-to-CDMA Handdown Threshold................................ +878) _____CDMA-to-Analog Handdown Threshold.............................. +879) _____Maximum Number of Active Set Pilots............................ +880) _Carrier Assignment Algorithm.+881)__ RF Loading Weight Factor.+882) ___Prim AltCDMA-to-CDMA Handoff Threshold...................+883) _____ +884) _____CDMA-to-Analog Handoff Threshold.................+885) _____ +886) _____Border Sector Distance Lower Threshold...........+887) 000.0 +888) _____Border Sector Distance Upper Threshold...........+889) 000.0 +890) _____Border Sector Distance Validity Check Period.....+891) 0 +892) __Border Sector Distance Upper Limit Difference....+893) 10 +894) __Border Sector Loss for Inter-Frequency Handoff...+895) ____ +896) ____Border Sector Loss for CDMA-to-Analog Handoff....+897) ____ +898) ____Border Pilot Versus Interior Pilot Threshold.....+899) ____ +900) ____903) Carriers Using Handoff/Border Alt:1 1 1 1 1 1 1 1 1 12 2 2 2 2 2 2 2 2 23 3 3 31 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Enter Review, Validate, screen#, or Print:________________________________________________________________________________ceqface第16页1321值为空CDMANetworks CELL EQUIPAGE FACE (ceqface) Screen 16 of 47 Cell 262 Face 1CDMA Information (Non-Power Control):Soft Swap Compatibility: Prim.+1252)_ Alt.+1253)_1256) Carriers Using Alt:1 1 1 1 1 1 1 1 1 12 2 2 2 2 2 2 2 2 23 3 3 31 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Request for Pilot Measurement: Prim.+1321) ___ Alt.+1322)__1325) Carriers Using Alt:1 1 1 1 1 1 1 1 1 12 2 2 2 2 2 2 2 2 23 3 3 31 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Bandclass for Dual Band Handoff Switch Alternate.......... 1390)_________ Enter Review, Validate, screen#, or Print:________________________________________________________________________________ ceqface第24页（导频数字增益值，查表配套设置）个别基站为了改变覆盖范围，需要调整数字增益值CDMANetworks CELL EQUIPAGE FACE (ceqface) Screen 24 of 47 Cell 262 Face 1CDMA Power Control ParametersForward Link:Pilot Channel Gain (dgu)............................. 1775)108Paging Channel Gain (dgu)............................ 1777)64Sync Channel Gain (dgu).............................. 1779)34Traffic Channel Voice Activity Factor................ 1781)1.00Enable Forward Link Power Control....................+1782)_Loading Threshold for High Capacity (%)..............+1783)___Rate Rate Set 1 Set 2 Nominal Traffic Channel Gain (dgu)...................+1784)___ +1785)___ Forward Frame Error Rate (%).........................+1786)1.0 +1787)1.0 Small Gain Increment (dgu)...........................+1788)__ +1789)__Target Frame Error Rate for High Capacity (%)........+1790)____ +1791)____ Gain Threshold for High Capacity (dgu)...............+1792)___ +1793)___Enter Review, Validate, screen#, or Print:________________________________________________________________________________ 普通内部小区邻区设置fci第15页 (邻区设置）（普通内部小区）CDMANetworks FACE CODE INFORMATION (fci) Screen 15 of 22 Cell 262 SG 0 Face 1274) CDMA Principal Neighbor ListAnlg Eqv Anlg Hard ExtendedCell Ant Plt Pri Ant Srv Only Ngbr Band Handoff CAM System ID BCCH Site Face PN Grp Face Grp Plt Conf Class Only AHO SHO AEHO DCS ECP SYS Supp 275)276)277)278)279) 280)281) 282) 283) 284) 285)286)287) 288)289)290) 291)[1] 262 2 246 0 _ _ n 0 850 n _ _ _ __ __ _____ _[2] 262 3 414 0 _ _ n 0 850 n _ _ _ __ __ _____ _[3] 69 2 240 1 _ _ n 0 850 n _ _ _ __ __ _____ _[4] 72 1 105 1 _ _ n 0 850 n _ _ _ __ __ _____ _[5] 86 2 225 1 _ _ n 0 850 n _ _ _ __ __ _____ _[6] 86 3 393 1 _ _ n 0 850 n _ _ _ __ __ _____ _[7] 86 1 57 1 _ _ n 0 850 n _ _ _ __ __ _____ _[8] 111 1 66 1 _ _ n 0 850 n _ _ _ __ __ _____ _[9] 111 3 402 1 _ _ n 0 850 n _ _ _ __ __ _____ _[10] 111 2 234 1 _ _ n 0 850 n _ _ _ __ __ _____ _[11] 134 1 126 1 _ _ n 0 850 n _ _ _ __ __ _____ _[12] 149 1 108 1 _ _ n 0 850 n _ _ _ __ __ _____ _ Enter Extended System ID when Neighbor Cell is on different Switch or MSC. Enter Review, Change-insert, Validate, screen#, or Print:朗讯MSC边界小区邻区设置如果添加的邻区与源小区不同MSC，需要添加PN值及DCS ECP SYS参数________________________________________________________________________________ fci第15页 (邻区设置）（朗讯MSC边界小区）CDMANetworks FACE CODE INFORMATION (fci) Screen 15 of 22 Cell 235 SG 0 Face 3274) CDMA Principal Neighbor ListAnlg Eqv Anlg Hard ExtendedCell Ant Plt Pri Ant Srv Only Ngbr Band Handoff CAM System ID BCCH Site Face PN Grp Face Grp Plt Conf Class Only AHO SHO AEHO DCS ECP SYS Supp 275)276)277)278)279) 280)281) 282) 283) 284) 285)286)287) 288)289)290) 291)[1] 235 1 144 0 _ _ n 0 850 n _ _ _ __ __ _____ _[2] 235 2 312 0 _ _ n 0 850 n _ _ _ __ __ _____ _[3] 129 3 492 1 _ _ n 0 850 n _ _ _ __ __ _____ _[4] 129 1 156 1 _ _ n 0 850 n _ _ _ __ __ _____ _[5] 173 3 390 1 _ _ n 0 850 n _ _ _ __ __ _____ _[6] 191 3 378 1 _ _ n 0 850 n _ _ _ __ __ _____ _[7] 439 1 18 1 _ _ n 0 850 n _ _ _ 12 5 13956 _[8] 439 2 186 1 _ _ n 0 850 n _ _ _ 12 5 13956 _[9] 440 1 120 1 _ _ n 0 850 n _ _ _ 12 5 13956 _。