ASTM A792-A792M-2003
美标目录大全ASTMABCDEFGP
美标目录大全ASTM A B C D E F GP美标目录大全ASTM A-B-C-D-E-F-G-P(下)2010-12-09 A736/A736M-03低碳时效硬化的镍铜铬钼铌和镍铜锰钼铌合金钢压力容器板Standard Specification for Pressure Vessel Plates,Low-Carbon Age-Hardening Nickel-Copper-Chromium-Molybdenum-Columbium and Nickel-Copper-Manganese-Molybdenum-Columbium Alloy Steel A737/A737M-99高强度低合金钢压力容器板Standard Specification for Pressure Vessel Plates,High-Strength,Low-Alloy Steel A738/A738M-03a中温和低温装备用经热处理的碳锰硅钢压力容器板Standard Specification for Pressure Vessel Plates,Heat-Treated,Carbon-Manganese-Silicon Steel,for Moderate and Lower Temperature Service A739-90a(2000)升温或者/和加压部件用热轧合金钢棒Standard Specification for Steel Bars,Alloy,Hot-Wrought,for Elevated Temperature or Pressure-Containing Parts,or Both A740-98(2003)钢丝网(编织或者焊接电镀钢丝网)Standard Specification for Hardware Cloth(Woven or Welded Galvanized Steel Wire Fabric)A741-98(2003)马路护栏用镀锌钢丝绳和配件Standard Specification for Zinc-Coated Steel Wire Rope and Fittings for Highway Guardrail A742/A742M-03波纹钢管用预涂聚合物和金属涂覆钢薄板Standard Specification for Steel Sheet,Met allic Coated and Polymer Prec oated for Corrugated Steel Pipe A743/A743M-03一般用耐腐蚀铬铁及镍铬铁合金铸件Standard Specification for Castings,Iron-Chromium,Iron-Chromium-Nickel,Corrosion Resistant,for General Application A744/A744M-00e1严酷条件下使用的耐腐蚀镍铬铁合金铸件Standard Specification for Castings,Iron-Chromium-Nickel,Corrosion Resistant,for Severe Service A745/A745M-94(2003)奥氏体钢锻件的超声波查验Standard Practice for Ultrasonic Examination of Austenitic Steel Forgings A746-03排污管用球墨铸铁Standard Specification for Ductile Iron Gravity Sewer PipeA747/A747M-99沉淀硬化不锈钢铸件Standard Specification for SteelCastings,Stainless,Precipitation Hardening A748/A748M-87(2003)压力容器用静态铸造的激冷白口铁-灰口铁双金属轧辊Standard Specification for Statically Cast Chilled White Iron-Gray Iron Dual Metal Rolls for Pressure Vessel Use A749/A749M-97(2002)热轧碳素钢和高强度低合金钢带材通用要求Standard Specification for Steel,Strip,Carbon and High-Strength,Low-Alloy,Hot-Rolled,General Requirements for A751-01钢制品化学分析的实验方法、操作和术语Standard Test Methods,Practices,and Terminology for Chemical Analysis of Steel Products A752-04合金钢条和粗圆铁丝Standard Specification for General Requirements for Wire Rods and Coarse Round Wire,Alloy Steel A752M-04合金钢条和粗圆铁丝(国际公制)Standard Specification for General Requirements for Wire Rods and Coarse Round Wire,Alloy Steel[Metric]A753-02镍铁软磁合金Standard Specification for Wrought Nickel-Iron Soft Magnetic Alloys(UNSK94490,K94840,N14076,N14080)A754/A754M-96(2000)X射线荧光涂层厚度的试验方法Standard Test Method for Coating Weight(Mass)of Metallic Coatings on Steel by X-Ray Fluorescence A755/A755M-03外露建筑材料用热浸涂覆和用卷涂工艺预涂的钢薄板Standard Specification for Steel Sheet,Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products A756-94(2001)耐磨不锈轴承钢Standard Specification for Stainless Anti-Friction Bearing Steel A757/A757M-00低温下承压装备及其他装备用铁素体和马氏体钢铸件Standard Specification for Steel Castings,Ferritic and Marte nsitic,for Pressure-Containing and Other Applications,for Low-Temperature Service A758/A758M-00具备改进的切口韧性的对缝焊锻制碳素钢管配件Standard Specification for Wrought-Carbon Steel Butt-Welding Piping Fittin gs with Improved Notch Toughness A759-00起重机用碳铁轨条Standard Specification for Carbon Steel Crane Rails A760/A760M-01a 下水道和排水沟用金属涂覆的波纹钢管Standard Specification for Corrugated Steel Pipe,Metallic-Coated for Sewers and DrainsA761/A761M-04现场栓接受、管拱和拱用波纹镀锌结构钢板Standard Specification for Corrugated Steel Structural Plate,Zinc-Coated,for Field-Bolted Pipe,Pipe-Arches,and Arches A762/A762M-00下水道和排水沟用预涂聚合物波纹钢管Standard Specification for Corrugated Steel Pipe,Polymer Precoated for Sewers and Drains A763-93(2004)铁素体不锈钢晶间腐蚀敏感性检测Standard Practices for Detecting Susceptibility to Intergranular Attack in Ferritic Stainless Steels A764-95(2001)机械弹簧用冷拉镀锌和按成品尺寸镀锌的碳素钢丝Standard Specification for Metallic Coated Carbon Steel Wire,Coated at Size and Drawn to Sizefor Mechanical Sp rings A765/A765M-01具备强力压制性韧性要求的碳素钢及低合金钢压力容器部件锻件Standard Specification for Carbon Steel and Low-Alloy Steel Pressure-Vessel-Component Forgings with Mandatory Toughness Requirements A767/A767M-00b钢筋混凝土用镀锌钢筋Standard Specification for Zinc-Coated(Galvanized)Steel Bars for Concrete Reinforcement A768-95(2001)涡轮机转子及轴用经真空处理的含铬12%的合金钢锻件Standard Specification for Vacuum-Treated 12%Chromium Alloy Steel Forgings for Turbine Rotors and Shafts A769/A769M-00电阻焊钢结构型材Standard Specification for Carbon and High-Strength Electric Resistance Welded Steel Structural Shapes A770/A770M-03专用钢板通过厚度丈量进行的抗拉试验Standard Specification for Through-Thickness Tension Testing of Steel Plates for Special Applications A771/A771M-95(2001)增殖反应堆堆芯部件用奥氏体不锈钢管Standard Specification for Seamless Austenitic and Martensitic Stainless Steel Tubing for Liquid Metal-Cooled Reactor Core Components A772/A772M-00正弦电流用材料的交流磁导率的试验方法Standard Test Method for ac Magnetic Permeability of Materials Using Sinusoidal Current A773/A773M-01用带直流电子的磁滞曲线记录仪的(B-H)回路法丈量材料的磁性能的标准试验方法Standard Test Method for dc Magnetic Properties of Materials Using Ring and Permeameter Procedures with dc Electronic Hysteresigraphs A774/A774M-02低温和中温一般腐蚀情况下用的焊接锻制奥氏体不锈钢配件Standard Specification for As-Welded Wrought Austenitic Stainless Steel Fittings for General Corrosive Service at Low and Moderate Temperatures A775/A775M-04a涂环氧树脂的钢筋钢棒StandardSpecification for Epoxy-Coated Steel Reinforcing Bars A778-01焊接未退火的奥氏体不锈钢管形制品Standard Specification forWelded,Unannealed Austenitic Stainless Steel Tubular ProductsA779/A779M-00预应力混凝土用应力消除未涂覆的密实七股钢丝绞绳Standard Specification for Steel Strand,Seven-Wire,Uncoated,Compacted,Stress-Relieved for Prestressed Concrete A780-01热浸镀锌层的损坏及无覆层区域的检修Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings A781/A781M-04a一般工业用一般要求的钢和合金铸件Standard Specification for Castings,Steel and Alloy,Common Requirements,for General Industrial Use A782/A782M-90(2001)经淬火和回火的锰铬钼硅锆合金钢压力容器板Standard Specification for Pressure-Vessel Plates,Quenched-and-Tempered,Manganese-Chromium-Molybdenum-Silicon Zirconium Alloy Steel A786/A786M-00b轧制钢楼板Standard Specification for Hot-Rolled Carbon,Low-Alloy,High-Strength Low-Alloy,and Alloy Steel Floor Plates A787-01电阻焊金属涂覆碳素钢机械配管Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing A788-04a钢锻件Standard Specification for Steel Forgings,General Requirements A789/A789M-04a 平凡装备用无缝与焊接铁素体/奥氏体不锈钢管Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service A790/A790M-04a无缝与焊接铁素体/奥氏体不锈钢管Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe A792/A792M-03热浸工艺法处理的55%铝-锌合金涂覆钢板Standard Specification for Steel Sheet,55%Aluminum-Zinc Alloy-Coated by the Hot-Dip Process A793-96(2001)不锈钢轧制楼板Standard Specific ation for Rolled Floor Plate,Stainless Steel A794-97(2002)商品级冷轧碳素钢薄板(无上含碳量为0.16%-0.25%)Standard Specificationfor Commercial Steel(CS),Sheet,Carbon(0.16%Maximum to0.25%Maximum),Cold-Rolled A795/A795M-04防火用黑色及热浸镀锌的焊接和无缝钢管Standard Specification for Black and Hot-Dipped Zinc-Coated(Galvanized)Welded and Seamless Steel Pipe for Fire Protection Use A796/A796M-04雨水管和卫生污水管及其他地下埋设管道用波纹钢管、管托架及拱形架结构设计惯例Standard Practice for Structural Design of Corrugated Steel Pipe,Pipe-Arches,an dArches for Storm and SanitarySewers and Other Buried Applications A798/A798M-01下水道及其他近似用途用工厂制波纹钢管的安装Standard Practice for Installing Factory-Made Corrugated Steel Pipe for Sewers and Other ApplicationsA799/A799M-04估算不锈钢铸件铁素体含量用仪表的校准Standard Practice for Steel Castings,Stainless,Instrument Calibration,for Estimating Ferrite Content A800/A800M-01奥氏体合金钢铸件中铁素体含量的估算Standard Practice for Steel Casting,Austenitic Alloy,Estimating Ferrite Content Thereof A801/A801M-99铁钴高磁性饱和合金Standard Specification for Wrought Iron-Cobalt High Magnetic Saturation Alloys UNS R30005 and K92650 A802/A802M-95(2001)钢铸件外不雅查验的表面验收标准Standard Practice for Steel Castings,Surface Acceptance Standards,Visual Examination A803/A803M-03焊接铁素体不锈钢给水加热器管Standard Specification for Welded Ferritic Stainless Steel Feedwater Heater Tubes A804/A804M-04在电力频率下用薄钢板型试样对材料交流磁特性的测试方法Standard Test Methods for Alternating-Current Magnetic Properties of Materials at Power Frequencies Using Sheet-Type Test Specimens A805-93(2002)冷轧碳素钢扁平线Standard Specification for Steel,Flat Wire,Carbon,Cold-Rolled A807/A807M-02e1下水道及其他近似用途用波纹结构钢涂覆管的安装Standard Practice for Installing Corrugated Steel Structural Plate Pipe for Sewers and Other Applications A808/A808M-00a具备改进的切口韧性的结构级高强度低合金碳钢、锰钢、铌钢和钒钢Standard Specification for High-Strength,Low-Alloy Carbon,Manganese,Columbium,Vanadium Steel of Structural Quality with Improved Notch Toughness A809-98镀铝碳素钢丝Standard Specifi cation for Aluminum-Coated(Aluminized)Carbon Steel Wire A810-01镀锌钢管用绕网Standard Specification for Zinc-Coated(Galvanized)Steel Pipe Winding Mesh A811-03粉末冶金技术制造的软磁石零件Standard Specification for Soft Magnetic Iron Parts Fabricated by Powder Metallurgy(P/M)Techniques A813/A813M-01单或者双焊接奥氏体不锈钢管Standard Specification for Single-or Double-Welded Austenitic Stainless Steel Pipe A814/A814M-03冷加工焊接奥氏体不锈钢管Standard Specification for Cold-Worked Welded Austenitic StainlessSteel Pipe A815/A815M-04锻制铁素体、铁素体/奥氏体和马氏体不锈钢管配件Standard Specification for WroughtFerritic,Ferritic/Austenitic,and Martensitic Stainless Steel Piping Fittings A8 17-03链接栅子网用金属涂覆钢丝Standard Specification for Metallic-Coated Steel Wire for Chain-Link Fence Fabric and Marcelled Tension Wire A818-91(2001)镀铜碳素钢丝Standard Specification for Coppered Carbon Steel Wire A820/A820M-04纤维增强混凝土用钢纤维Standard Specification for Steel Fibers for Fiber-Reinforced Concrete A821/A821M-99预应力混凝土容器用经回火的冷拉钢丝StandardSpecification for Steel Wire,Hard Drawn for Prestressing Concrete Tanks A822-90(2003)液压系统装备用冷拉碳素无缝钢管Standard Specification for Seamless Cold-Drawn Carbon Steel Tubing for Hydraulic System Service A823-99(2003)静铸永久铸模灰铸件Standard Specification for Statically Cast Permanent Mold Gray Iron CastingsA824-01链接栅子用Marcelled拉力金属涂覆钢丝Standard Specificationfor Metallic-Coated Steel Marcelled Tension Wire for Use With Chain Link Fence A827/A827M-02锻造及近似用途用的碳素钢板技术规范Standard Specification for Plates,Carbon Steel,for Forging and Similar Applications A829/A829M-04结构性合金钢板Standard Specification for Alloy Structural Steel Plates A830/A830M-02按照化学成分要求提供的碳素钢板技术规范Standard Specification for Plates,Carbon Steel,Structural Quality,Furnished to Chemical Composition Requirements A831/A831M-95(2000)核心部件用不锈耐热钢棒,坯段及锻件规格Standard Specification for Austenitic and Martensitic Stainless SteelBars,Billets,and Forgings for Liquid Metal Cooled Reactor Core Components A832/A832M-99e1压力容器板用铬钼钒及铬钼钒钛硼合金钢Standard Specification for Pressure Vessel Plates,AlloySteel,Chromium-Molybdenum-Vanadium A833-84(2001)用比力硬度测试仪丈量金属材料的压痕硬性Standard Practice for Indentation Hardness of Metallic Materials by Comparison Hardness Testers A834-95(2001)一般工业用铁铸件的一般要求Standard Specification for Common Requirements for Iron Castings for General Industrial Use A835-84(2000)铁合金与合金添加剂的筛分粒度Standard Specification for Sizes of Ferroalloys and Alloy Additives A836/A836M-02搪瓷管和压力容器装备用钛稳定碳素体钢锻件Standard Specification for Titanium-Stabilized Carbon Steel Forgings for Glass-Lined Piping and Pressure Vessel ServiceA837/A837M-03渗碳用合金钢锻件Standard Specification for Steel Forgings,Alloy,for Carburizing Applications A838-02继电器用易切削铁素体不锈软磁合金技术规范Standard Specification for Fr ee-Machining Ferritic Stainless Soft Magnetic Alloy Bar for Relay ApplicationsA839-02软磁用途的磷铁粉末冶金制造的零件技术规范Standard Specification for Iron-Phosphorus Powder Meta llurgy(P/M)Parts for Soft Magnetic Applications A840/A840M-00全处理的磁性夹层钢Standard Specification for Fully Processed Magnetic Lamination SteelA841/A841M-03a压力容器用温度机械控制工艺加工的钢板Standard Specification for Steel Plates for Pressure Vessels,Produced by Thermo-Mechanical Control Process(TMCP)A842-85(2004)高疏密程度石墨铸铁Standard Specification for Compacted Graphite Iron CastingsA844/A844M-93(1999)压力容器用直接淬火加工的含镍9%的合金钢板Standard Specification for Steel Plates,9%Nickel Alloy,for PressureVessels,Produced by the Direct-Quenching Process A845-85(2000)用于脱氧与合金钢的钛碎片Standard Specification for Titanium Scrap for Use in Deoxidation and Alloying of Steel A846-85(2000)用于脱氧与合金钢的铝碎片Standard Specification for Aluminum Scrap for Use in Deoxidation and Alloying of Steel A847-99a(2003)具备增强耐大气腐蚀性能的冷成型焊接与无缝高强度低合金结构管Standard Specification for Cold-Formed Welded and Seamless High Strength,L ow Alloy Structural Tubing with Improved Atmospheric Corrosion Resistance A848-01低碳磁石Standard Specification for Low-Carbon Magnetic Iron A849-00波纹钢排水管和污水管用后涂覆铺面和衬里材料Standard Specification for Post-Applied Coatings,Pavings,and Linings for Corrugated Steel Sewer and Drainage Pipe A852/A852M-03最小屈服强度为70Ksi(485MPa),厚度为4英寸(100mm)的经淬火和回火的低合金结构钢板Standard Specification for Quenched and Tempered Low-Alloy Structural Steel Plate with 70ksi[485 MPa]Minimum Yield Strength to 4in.[100 mm]Thick A853-04平凡碳素钢丝Standard Specification for Steel Wire,Carbon,for General Use A854/A854M-98(2003)镀锌高强度钢栅子和格架用光滑金属线Standard Specification for Metallic-Coated Steel Smooth High-Tensile Fence and Trellis Wire A855/A855M-03锌-5%铝-铈合金涂覆的钢丝绳Standard Specification for Zinc-5%Aluminum-Mischmetal Alloy-Coated Steel Wire Strand A856/A856M-03锌-5%铝-铈合金涂覆的碳素钢丝Standard Specification for Zinc-5%Aluminum-Mischmetal Alloy-Coated Carbon Steel Wire A857/A857M-00a冷成形轻型薄钢板桩Standard Specificationfor Steel Sheet Piling,Cold Formed,Light Gage A858/A858M-00低温和腐蚀情况下用热处理碳素钢配件Standard Specification for Heat-Treated Carbon Steel Fittings for Low-Temperature and Corrosive ServiceA859/A859M-04压力容器部件用时效硬化镍铜铬钼钶低碳合金钢锻件Standard Specification for Age-Hardening Alloy Steel Forgings for Pressure Vessel Components A860/A860M-00锻制高强度低合金钢的高强度对缝焊接配件Standard Specification for Wrought High-Strength Low-Alloy Steel Butt-Welding Fittings A861-04高硅铁管和配件Standard Specificationfor High-Silicon Iron Pipe and Fittings A862/A862M-98(2003)波纹钢污水管和排水管沥清(柏油)涂层的应用Standard Practice for Application of Asphalt Coatings to Corrugated Steel Sewer and Drainage Pipe A865-03钢管连接用黑色或者镀锌焊接或者无缝钢螺纹接头Standard Specification for Threaded Couplings,Steel,Black or Zinc-Coated(Galvanized)Welded or Seamless,for Use in Steel Pipe Joints A866-01耐磨中碳轴承钢Standard Specification for Medium Carbon Anti-Friction Bearing Steel A867-03继电器用铁硅钢Standard Specification for Iron-Silicon Relay Steels A871/A871M-03抗空气腐蚀的高强度低合金结构钢板Standard Specification for High-Strength Low-Alloy Structural Steel Plate With Atmospheric Corrosion Re sistance A872/A872M-02腐蚀环境下用离心铸造铁素体/奥氏体不锈钢管Standard Specification for Centrifugally Cast Ferritic/Austenitic Stainless Steel Pipe for Corrosive EnvironmentsA874/A874M-98适于低温使用的铁素体球墨铸铁铸件Standard Specification for Ferritic Ductile Iron Castings Suitable for Low-TemperatureService A875/A875M-02a热浸处理的锌-5%铝合金金属涂覆的钢薄板Standard Specification for Steel Sheet,Zinc-5%Aluminum Alloy-Coated by theHot-Dip Process A876-03全处理型平轧的晶粒取向的硅铁电工钢Standard Specification for Flat-Rolled,Grain-Oriented,Silicon-Iron,Electrical Steel,Fully Processed Types A877/A877M-99铬硅合金阀弹簧级钢丝Standard Specification for Steel Wire,Chromium-Silicon Alloy Valve Spring Quality A878/A878M-99经改良的铬钒阀弹簧级钢丝Standard Specification for Steel Wire,Modified Chromium Vanadium Valve Spring Quality A879-00每面镀层质量应予标明的电解镀锌薄钢板Standard Specification for Steel Sheet,Zinc Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface A881/A881M-02预应力混凝土铁路轨枕用应力消除或者应力松弛变形钢丝Standard Specification for Steel Wire,Deformed,Stress-R elievedor Low-Relaxation for Prestressed Concrete Railroad Ties A882/A882M-04a涂环氧树脂的七股预应力钢丝绳Standard Specification for Filled Epoxy-Coated Seven-Wire Prestressing Steel Strand A883/A883M-01非金属磁性材料铁磁共振行距和旋磁比值的测试方法Standard Test Method for Ferrimagnetic Resonance Linewidth and Gyromagnetic Ratio of Nonmetallic Magnetic Materials A884/A884M-04钢筋用涂环氧树脂的钢丝与焊接钢丝织网的技术规范Standard Specification for Epoxy-Coated Steel Wire and Welded Wire Reinforcement A885/A885M-96(2002)波纹钢制下水沟、暗渠和雨水管用锌和聚芳基酰胺纤维复合涂覆钢板Standard Specificationfor Steel Sheet,Zinc and Aramid Fiber Composite Coated for Corrugated Steel Sewer,Culvert,and Underdrain Pipe A886/A886M-02预应力混凝土用应力消除的七股齿纹钢丝绳Standard Specification for SteelStrand,Indented,Seven-Wire Stress-Relieved for Prestressed ConcreteA887-89(2000)核能装备用经硼酸处理的不锈钢板、薄板及带材Standard Specification for Borated Stainless Steel Plate,Sheet,and Strip for Nuclear Application A888-04下水管、雨水管、污水管和排气管道用无衬套铸铁管和配件Standard Specification for Hubless Cast Iron Soil Pipeand Fittings for Sanitary and Storm Drain,Wa ste,and Vent Piping Applications A889/A889M-03在低感应条件下用万用表法和25厘米艾普斯亭(Epstein)框测定材料的交流磁特性的试验方法Standard Test Method for Alternating-Current Magnetic Properties of Materials at Low Inductions Using the Wattmeter-Varmeter-Ammeter-Voltmeter Method and 25-cm(250-mm)Epstein Frame A890/A890M-99(2003)平凡应用的铁铬镍钼耐腐蚀双重(奥氏体/铁素体)铸件Standard Specification for Castings,Iron-Chromium-Nickel-Molybdenum Corrosion-Resistant,Duplex(Austenitic/Ferritic)for General Application A891-98(2003)涡轮机转子圆盘和轮用沉淀硬化铁基超合金钢锻件Standard Specification for Precipitation Hardening Iron Base Superalloy Forgings for Turbine Rotor Disks and Wheels A892-88(2001)高碳轴承钢微不雅结构的定义和等级Standard Guide for Defining and Rating the Microstructure of High Carbon Bearing Steels A893/A893M-03微波频率下非金属磁性材料复合介电常数的测试方法Standard Test Method for Complex Dielectric Constant of Nonmetallic Magnetic Materials at Microwave Frequencies A894/A894M-00非金磁性材料的饱和磁化强度或者磁感应性能的标准试验方法Standard Test Method for Saturation Magnetization or Induction of Nonmetallic Magnetic Materials A895-89(2000)易切削不锈钢板、薄板和带材Standard Specification for Free-Machining Stainless Steel Plate,Sheet,and Strip A896-89(2004)电镀结构导电壳的研究Standard Practice for Conducting Case Studies on Galvanized Structures A897/A897M-03等温淬火球墨铸铁Standard Specification for Austempered Ductile Iron Castings A898/A898M-91(2001)轧制结构钢型材的直束超声查验Standard Specification for Straight Beam Ultrasonic Examination of Rolled Steel Structural Shapes A899-91(2002)环氧涂层钢丝Standard Specification for Steel Wire,Epoxy-Coated A900/A900M-01非晶磁性带材叠装系数的测试方法Standard Test Method for Lamination Factor of Amorphous Magnetic Strip A901-03半成品型非晶形磁芯合金Standard Specification for Amorphous Magnetic Core Alloys,Semi-Processed Types A902-03与金属涂覆的钢制品涉及的标准技术术语Standard Terminology Relating to Metallic Coated Steel Products A903/A903M-99(2003)钢铸件磁粉探伤和荧光渗透查验的表面验收标准Standard Specification for Steel Castings,Surface AcceptanceStandards,Magnetic Particle and Liquid Penetrant Inspection A904-04 50镍-50铁粉末冶金(P/M)软磁合金Standard Specification for 50 Nickel-50 Iron Powder Metallurgy(P/M)Soft Magnetic Parts A905-93(1998)压力容器环绕纠缠用钢丝Standard Specification for Steel Wire,Pressure Vessel Winding A906/A906M-02高架提升装备用的80级和100级合金钢悬链规范Standard Specification for Grade 80 and Grade 100 Alloy Steel Chain Slings for Overhead Lifting A908-03不锈钢针管Standard Specification for Stainless Steel Needle Tubing A909-03一般企业用微合金钢锻件Standard Specification for Steel Forgings,Microalloy,for General Industrial Use A910/A910M-99预应力混凝土用无涂层、无焊缝、2股及3股钢绞绳Standard Specification for Uncoated,Weldless,2-and 3-Wire Steel Strand for Prestressed Concrete A911/A911M-02预应力混凝土轨枕用无涂层的预应力消除的钢棒Standard Specification for Uncoated,Stress-Relieved Steel Bars for Prestressed Concrete TiesA912/A912M-04用万用表圆环样品法测试非晶材料在电频率条件下交流磁特性的试验方法Standard Test Method for Alternating-Current Magnetic Properties of Amorphous Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method with Toroidal SpecimensA913/A913M-04经淬火和自回火(QST)处理的高强度低合金结构级钢型材Standard Specification for High-Strength Low-Alloy Steel Shapes of Structural Quality,Produced by Quenching and Self-TemperingProcess(QST)A914/A914M-92(1999)e1对末端淬火淬透性有限定要求的钢棒材技术规范Standard Specification for Steel Bars Subject to Restricted End-Quench Hardenability Requirements A915/A915M-93(2003)化学要求同锻件近是的碳素钢和合金钢Standard Specification for SteelCastings,Carbon,and Alloy,Chemical Requirements Similar to Standard Wrought Grades A917-00要求每壁标识有镀层质量用的电解工艺涂层的薄钢板材标准规范Standard Specification for Steel Sheet,Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface(General Requirements)A 918-00要求在每壁标识有涂层质量用电解工艺镀锌镍合金的薄钢板技术规范Standard Specification for Steel Sheet,Zinc-Nickel Alloy Coated by theElectrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface A920/A920M-02a具备机械特性,微合金,热锻,高质量钢棒的标准规范Standard Specification for SteelBars,Microalloy,Hot-Wrought,Special Quality,Mechanical PropertiesA921/A921M-93(1999)后热锻用微合金,高质量,热锻钢棒的标准规范Standard Specification for Steel Bars,Microalloy,Hot-Wrought,SpecialQuality,for Subsequent Hot Forging A922-93(2000)硅金属标准规范Standard Specification for Silicon Metal A923-03检测锻制双重奥氏体/铁素体不锈钢中有害金属间相的标准试验方法Standard Test Methods for Detecting Detrimental Intermetallic Phase in Wrought DuplexAustenitic/Ferritic Stainless Steels A924/A924M-04用热浸镀法对薄钢板金属涂层的一般要求的标准规范Standard Specification for General Requirements for Steel Sheet,Metallic-Coated by the Hot-Dip Process A925-03锌-5%铝.混合稀土合金涂覆钢的地面金属绞线的技术规范Standard Specification for Zinc-5%Aluminum-Mischmetal Alloy-Coated Steel Overhead Ground Wire Strand A926-03波纹形金属管用比力涂层材料磨耗阻力的标准测试方法Standard Test Method for Comparing the Abrasion Resistance of Coating Materials for Corrugated Metal Pipe A927/A927M-99使用伏特计-电流计-瓦特计方法的圆环铁芯交流磁性能的标准试验方法Standard Test Method for Alternating-Current Magnetic Properties of Toroidal Core Specimens Using the Voltmeter-Ammeter-Wattmeter Method A928/A928M-04加填料金属电熔焊铁素体/奥氏体(二联)不锈钢管标准规范Standard Specification for Ferritic/Austenitic(Duplex)Stainless Steel Pipe Electric Fusion Welded with Addition of Filler Metal A929/A929M-01波纹钢管用的经热浸处理的金属镀覆薄钢板标准规范Standard Specification for Steel Sheet,Metallic-Coated by the Hot-Dip Process for Corrugated Steel Pipe A930-03涵洞,暴雨下水道和其他地下的排水道用波形金属管的生存的年限周期用度分析的标准惯例Standard Practice for Life-Cycle Cost Analysis of Corrugated Metal Pipe Used forCulverts,Storm Sewers,and Other Buried Conduits A931-96(2002)金属丝绳和绞线拉伸试验的标准试验方法Standard Test Method for Tension Testing of Wire Ropes and Strand A932/A932M-01用瓦特计-安培计-伏特计和薄钢板样品测试在电源频率下非晶体材料交流磁性能的标准试验方法Standard Test Method for Alternating-Current Magnetic Properties of Amorphous Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method with Sheet Specimens A933/A933M-95(2001)加筋增强用聚氯乙烯涂层钢丝和焊接钢丝网的标准规范Standard Specification forVinyl(PVC)Coated Steel Wire and Welded Wire Fabric for Reinforcement A934/A934M-04环氧基树脂涂覆的预制增强钢棒的标准规范Standard Specification for Epoxy-Coated Prefabricated Steel Reinforcing Bars A937/A937M-01使用临界试验面测定绝缘涂层层间阻力的标准测试方法Standard Test Method for Determining Interlaminar Resistance of Insulating Coatings Using Two Adjacent Test Surfaces A938-97(2003)丝材抗扭试验的标准试验方法Standard Test Me thod for Torsion Testing of Wire历史上的今天：名牌阀门吹动温州美标阀门出口外贸2010-12-09蔬菜大棚用镀锌钢管2010-12-09美标钢管石油套管美标石油套管价格2010-12-09特别声明：1：资料来源于互联网，版权归属原作者2：资料内容属于网络意见，与本账号立场无关3：如有侵权，请告知，立即删除。
ASTM-美国涂层标准
20
ANSI/AWWA C116/A 21.162003
供水设备用球墨铸铁和灰铁配件的内外表面的 防护熔融胶合环氧涂层 给水钢管煤焦油保护涂层和内衬.热用搪瓷和 胶带 钢制供水管道的煤焦油保护涂层和内衬标准. 搪瓷和胶带.热水 商用4英寸和4英寸以上钢水管的水泥灰浆保护 衬和涂层 钢水管用特殊部件、连接件和配件的外部用低 温磁带涂层 钢制水管的内外层用液体环氧树脂涂层系统 给水钢管的内、外层熔化粘结环氧涂层 钢制水管内外的熔融胶合环氧树脂涂层 钢制水管的外层用挤压聚烯烃涂层 给水钢管用专用部件、连接件和配件外部可热 收缩交联的聚烯烃涂层 钢水管和配件聚氨基甲酸乙酯内或外涂层 钢水管、连接件、配件和特殊部件的内部和外 部用尼龙11基聚酰胺涂层系统 阀门和给水栓用防护性内部涂层 涂层的钢制储水箱 光纤涂层几何尺寸的测量方法 测量电器连接器件的金属涂层厚度的试验程序
10 ANSI/ASTM D2534-1988 11 ANSI/ASTM D3214-1997 12 ANSI/ASTM D3236-1988 13 ANSI/ASTM D3521-1986 14 ANSI/ASTM D3708-1988 15 ANSI/ASTM D4917-1997 16 ANSI/ASTM D4918-1997 17 ANSI/ASTM F1916-1998 18 ANSI/ASTM F2016-2000 19 ANSI/AWS A4.4M-2001
用光截面显微镜测量铝阳极镀层厚度及不透明 表面的其它透明涂层厚度的试验方法 金属表面自催化(无电)镍磷涂层标准规范 用硝酸蒸汽测试金属基体上金涂层孔隙率的标 准试验方法 用扫描电子显微镜测量横截面测定金属涂层厚 度的方法 热浸涂层用锭铁模型中GALFAN(锌-5%铝-含铈 稀土)合金的标准规范 金属涂层和无机物涂层的不同抽样 镉电沉积涂层标准规范 用重量分析法和其它化学分析法测定电沉积涂 层及相关涂层单位面积的质量 用凝胶体电谱法测定金属基物上金或钯涂层孔 隙度的标准试验方法 用湿硫黄蒸气("硫黄华")作金属涂层中孔隙率 测试的标准试验方法 用聚硫化物浸入法测试金属涂层中总疵点和机 械损坏的标准试验方法 镁和镁合金上非电解质转换涂层的标准规范 工程应用硬涂层阳极氧化规范 在锌和镉表面非铬酸涂层试验的标准实施规程 热处理平板玻璃的标准规范.HS和FT类涂层和 无涂层玻璃 建筑物内部辐射控制涂层系统(IRCCS)的安装 和使用的标准实施规程 建筑物外部防太阳辐射涂层的标准规范 用定量单点划痕试验测定陶瓷涂层粘结强度和 机械损坏类型的标准试验方法 涂层砖(由粘土或页岩制造的实心砌块)的标准 规范
对照表
23456附表2 JIS(JIS G 3312—87)：JIS G 3312—87备注：根据供需双方的协议，可将610mm的钢带宽度作为标准宽度。
附表10 JIS(JIS G 3312—87)厚度的允许偏差mm附表11 JIS(JIS G 3312—87)厚度的允许偏差mm附表12 JIS(JIS G 3312—87)宽度及长度允许偏差mm附表13 JIS(JIS G 3312—87)横向弯曲的最大值mm注：平直度应放置在平台上测定，其数值为从应变的最大值减去钢板厚度，适用于钢板的上侧表面。
注：①经供需双方协商，可供应宽度小于700mm的纵切钢带。
②厚度系指钢板和钢带涂层前基板的厚度。
附表22 (GB/T 12754─****征求意见稿)附表23 (GB/T 12754─****征求意见稿)附表24 (GB/T 12754─****征求意见稿)附表25 (GB/T 12754─****征求意见稿)附表26 (GB/T 12754─****征求意见稿)附表27 (GB/T 12754─****征求意见稿)附表28 (GB/T 12754─****征求意见稿)附表29 (GB/T 12754─****征求意见稿)附表30 (GB/T 12754─****征求意见稿)附表31(GB/T 12754─****征求意见稿)附表32(GB/T 12754─****征求意见稿)附表33(GB/T 12754─****征求意见稿)附表34 (GB/T 12754─****征求意见稿)附表35 （EN10169-1）附表36 （EN10169-1）附表37（EN10169-2）附表38 （EN10169-2）附表39 （EN10169-2）抗紫外线试验指数附表40 (GB/T 12754─****征求意见稿)附表40 (GB/T 12754─****征求意见稿)附表42 (GB/T 12754─91)可能的情况下，应存储在干燥和空调的环境中，一般来说，产品应该防潮并保证在运输过程中的干燥。
美国钢铁产品的标准比较多
美国钢铁产品的标准比较多，主要有以下几种：美国钢铁产品的标准比较多，主要有以下几种：ANSI 美国国家标准AISI??美国钢铁学会标准ASTM 美国材料与试验协会标准ASME 美国机械工程师协会标准AMS 航天材料规格（美国航空工业最常用的一种材料规格，由SAE制定）API 美国石油学会标准AWS 美国焊接协会标准SAE 美国机动车工程师协会标准MIL 美国军用标准QQ 美国联邦政府标准A216:：WCB , WCCA217: WC6 , WC9 , C5 (ZGCr5Mo)A351: CF8 , CF3 , CF3 M , CF8C标准号? ? ? ? 标准中文名称? ? ? ? 标准英文名称ASTM A1-00 ? ? ? ? 碳素钢丁字轨? ? ? ? Standard Specification for Carbon Steel Tee Rails ASTM A2-02 ? ? ? ? 普通型,带槽和防护型碳素工字钢轨? ? ? ? Standard Specification for Carbon Steel Girder Rails of Plain, Grooved, and Guard TypesASTM A3-01 ? ? ? ? 低、中、高碳素钢鱼尾（连接）板? ? ? ? Standard Specification for Steel Joint Bars, Low, Medium, and High Carbon (Non-Heat-Treated)ASTM A6/A6M-04a ? ? ? ? 轧制结构钢板材、型材和薄板桩通用技术要求? ? ? ? Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling ASTM A20/A20M-04a ? ? ? ? 压力容器用钢板材通用要求? ? ? ? Standard Specification for General Requirements for Steel Plates for Pressure VesselsASTM A27/A27M-03 ? ? ? ? 通用碳素钢铸件? ? ? ? Standard Specification for Steel Castings, Carbon, for General ApplicationASTM A29/A29M-04 ? ? ? ? 热锻及冷加工碳素钢和合金钢棒? ? ? ? Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements forASTM A31-04 ? ? ? ? 钢铆钉及铆钉和压力容器用棒材? ? ? ? Standard Specification for Steel Rivets and Bars for Rivets, Pressure VesselsASTM A34/A34M-01 ? ? ? ? 磁性材料的抽样和采购试验的标准惯例? ? ? ? Standard Practice for Sampling and Procurement Testing of Magnetic MaterialsASTM A36/A36M-04 ? ? ? ? 碳素结构钢技术规范? ? ? ? Standard Specification for Carbon Structural SteelASTM A47/A47M-99 ? ? ? ? 铁素体可锻铁铸件? ? ? ? Standard Specification for Ferritic Malleable Iron CastingsASTM A48/A48M-03 ? ? ? ? 灰铁铸件? ? ? ? Standard Specification for Gray Iron CastingsASTM A49-01 ? ? ? ? 经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板? ? ? ? Standard Specification for Heat-Treated Carbon Steel Joint Bars, Microalloyed Joint Bars, and Forged Carbon Steel Compromise Joint BarsASTM A53/A53M-04 ? ? ? ? 无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范? ? ? ? Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and SeamlessASTM A65-01 ? ? ? ? 钢轨道钉? ? ? ? Standard Specification for Steel Track SpikesASTM A66-01 ? ? ? ? 钢质螺旋道钉? ? ? ? Standard Specification for Steel Screw SpikesASTM A67-00 ? ? ? ? 热加工低碳钢和高碳钢垫板技术规范? ? ? ? Standard Specification for Steel Tie Plates, Low-Carbon and High-Carbon Hot-WorkedASTM A74-04 ? ? ? ? 铸铁污水管及配件的技术规范? ? ? ? Standard Specification for Cast Iron Soil Pipe and FittingsASTM A82-02 ? ? ? ? 钢筋混凝土用无节钢丝? ? ? ? Standard Specification for Steel Wire, Plain, for Concrete ReinforcementASTM A90/A90M-01 ? ? ? ? 镀锌和镀锌合金钢铁制品镀层重量的试验方法? ? ? ? Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings ASTM A99-03 ? ? ? ? 锰铁合金? ? ? ? Standard Specification for FerromanganeseASTM A100-04 ? ? ? ? 硅铁? ? ? ? Standard Specification for FerrosiliconASTM A101-04 ? ? ? ? 铬铁? ? ? ? Standard Specification for FerrochromiumASTM A102-04 ? ? ? ? 钒铁合金? ? ? ? Standard Specification for FerrovanadiumASTM A105/A105M-03 ? ? ? ? 管系部件用碳素钢锻件? ? ? ? Standard Specification for Carbon Steel Forgings for Piping ApplicationsASTM A106/A106M-04a ? ? ? ? 高温用无缝碳素钢管? ? ? ? Standard Specification for Seamless Carbon Steel Pipe for High-Temperature ServiceASTM A108-03 ? ? ? ? 优质冷加工碳素钢棒材技术规范? ? ? ? Standard Specification for Steel Bar, Carbon and Alloy, Cold-FinishedASTM A109/A109M-03 ? ? ? ? 冷轧碳素钢带技术规范? ? ? ? Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-RolledASTM A111-99a(2004)e1 ? ? ? ? 电话和电报线路用镀锌"铁"丝规格? ? ? ? Standard Specification for Zinc-Coated (Galvanized) Iron Telephone and Telegraph Line WireASTM A116-00 ? ? ? ? 镀锌钢丝编织栏栅网? ? ? ? Standard Specification for Metallic-Coated, Steel Woven Wire Fence FabricASTM A121-99(2004) ? ? ? ? 镀锌刺钢丝? ? ? ? Standard Specification for Mettalic-Coated Carbon Steel Barbed WireASTM A123/A123M-02 ? ? ? ? 钢铁产品的锌镀层（热浸镀锌）技术规范? ? ? ? Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM A125-96(2001) ? ? ? ? 热处理螺旋形钢弹簧? ? ? ? Standard Specification for Steel Springs, Helical, Heat-TreatedASTM A126-04 ? ? ? ? 阀门、法兰和管配件用灰铁铸件? ? ? ? Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe FittingsASTM A128/A128M-93(2003) ? ? ? ? 钢铸件,奥氏体锰? ? ? ? Standard Specification for Steel Castings, Austenitic ManganeseASTM A131/A131M-04 ? ? ? ? 海船用结构钢? ? ? ? Standard Specification for Structural Steel for ShipsASTM A132-04 ? ? ? ? 钼铁合金? ? ? ? Standard Specification for FerromolybdenumASTM A134-96(2001) ? ? ? ? 电熔(电弧)焊钢管(NPS为16英寸和16英寸以上)? ? ? ? Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)ASTM A135-01 ? ? ? ? 电阻焊钢管? ? ? ? Standard Specification for Electric-Resistance-Welded Steel PipeASTM A139/A139M-04 ? ? ? ? 电熔(电弧)焊钢管(4英寸以上的)? ? ? ? Standard Specification for Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and Over)ASTM A143/A143M-03 ? ? ? ? 热浸镀锌结构钢制品防脆裂措施和探测脆裂的程序? ? ? ? Standard Practice for Safeguarding Against Embrittlement of Hot-Dip Galvanized Structural Steel Products and Procedure for Detecting EmbrittlementASTM A144-02 ? ? ? ? 铁钨合金规范? ? ? ? Specification for FerrotungstenASTM A146-04 ? ? ? ? 氧化钼制品? ? ? ? Standard Specification for Molybdenum Oxide Products ASTM A148/A148M-03 ? ? ? ? 结构用高强度钢铸件? ? ? ? Standard Specification for Steel Castings, High Strength, for Structural PurposesASTM A153/A153M-04 ? ? ? ? 钢铁制金属构件上镀锌层(热浸)? ? ? ? Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareASTM A159-83(2001) ? ? ? ? 汽车用灰铁铸件? ? ? ? Standard Specification for Automotive Gray Iron CastingsASTM A167-99 ? ? ? ? 不锈钢和耐热铬镍钢板、薄板及带材? ? ? ? Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and StripASTM A176-99 ? ? ? ? 不锈钢和耐热铬钢板、薄板及带材? ? ? ? Standard Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and StripASTM A178/A178M-02 ? ? ? ? 电阻焊接碳素钢钢管及碳锰钢锅炉和过热器管的技术规范? ? ? ? Standard Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater TubesASTM A179/A179M-90a(2001) ? ? ? ? 热交换器和冷凝器用无缝冷拉低碳钢管? ? ? ? Standard Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes ASTM A181/A181M-01 ? ? ? ? 普通锻制碳素钢管的规格? ? ? ? Standard Specification for Carbon Steel Forgings, for General-Purpose PipingASTM A182/A182M-02 ? ? ? ? 高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件? ? ? ? Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature ServiceASTM A183-03 ? ? ? ? 钢轨用碳素钢螺栓和螺母? ? ? ? Standard Specification for Carbon Steel Track Bolts and NutsASTM A184/A184M-01 ? ? ? ? 混凝土加筋用变形钢筋编织网? ? ? ? Standard Specification for Fabricated Deformed Steel Bar Mats for Concrete ReinforcementASTM A185-02 ? ? ? ? 钢筋混凝土用焊接钢丝结构? ? ? ? Standard Specification for Steel Welded Wire Reinforcement, Plain, for ConcreteASTM A192/A192M-02 ? ? ? ? 高压用无缝碳素钢锅炉管? ? ? ? Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure ServiceASTM A193/A193M-04b ? ? ? ? 高温设备用合金钢和不锈钢螺栓材料? ? ? ? Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature ServiceASTM A194/A194M-04a ? ? ? ? 高温和高压设备用碳素钢与合金钢螺栓和螺母的规格? ? ? ? Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or BothASTM A197/A197M-00 ? ? ? ? 化铁炉用可锻铸铁? ? ? ? Standard Specification for Cupola Malleable IronASTM A202/A202M-03 ? ? ? ? 压力容器用铬锰硅合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Manganese-SiliconASTM A203/A203M-97(2003) ? ? ? ? 压力容器用镍合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, NickelASTM A204/A204M-03 ? ? ? ? 压力容器用钼合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, MolybdenumASTM A209/A209M-03 ? ? ? ? 锅炉和过热器用无缝碳钼合金钢管? ? ? ? Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater TubesASTM A210/A210M-02 ? ? ? ? 锅炉和过热器用无缝中碳素管? ? ? ? Standard Specification for Seamless Medium-Carbon Steel Boiler and Superheater TubesASTM A213/A213M-04 ? ? ? ? 无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管? ? ? ? Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, andHeat-Exchanger TubesASTM A214/A214M-96(2001) ? ? ? ? 热交换器与冷凝器用电阻焊接碳素钢管? ? ? ? Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes ASTM A216/A216M-93(2003) ? ? ? ? 高温下使用的适合于熔焊的碳素钢铸件规格? ? ? ? Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High- Temperature ServiceASTM A217/A217M-02 ? ? ? ? 适合高温受压零件用合金钢和马氏体不锈钢铸件? ? ? ? Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature ServiceASTM A220/A220M-99 ? ? ? ? 珠光体可锻铁? ? ? ? Standard Specification for Pearlitic Malleable IronASTM A225/A225M-03 ? ? ? ? 压力容器用锰矾镍合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-NickelASTM A227/A227M-99 ? ? ? ? 机械弹簧用冷拉钢丝? ? ? ? Standard Specification for Steel Wire, Cold-Drawn for Mechanical SpringsASTM A228/A228M-02 ? ? ? ? 乐器用优质弹簧钢丝? ? ? ? Standard Specification for Steel Wire, Music Spring QualityASTM A229/A229M-99 ? ? ? ? 机械弹簧用油回火的钢丝? ? ? ? Standard Specification for Steel Wire, Oil-Tempered for Mechanical SpringsASTM A230/A230M-99 ? ? ? ? 阀门用油回火优质碳素钢弹簧丝? ? ? ? Standard Specification for Steel Wire, Oil-Tempered Carbon Valve Spring QualityASTM A231/A231M-96(2002) ? ? ? ? 铬钒合金钢弹簧丝? ? ? ? Standard Specification for Chromium-Vanadium Alloy Steel Spring WireASTM A232/A232M-99 ? ? ? ? 阀门用优质铬钒合金钢弹簧丝? ? ? ? Standard Specification for Chromium-Vanadium Alloy Steel Valve Spring Quality WireASTM A234/A234M-04 ? ? ? ? 中温与高温下使用的锻制碳素钢及合金钢管配件? ? ? ? Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature ServiceASTM A239-95(2004) ? ? ? ? 用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法? ? ? ? Standard Practice for Locating the Thinnest Spot in a Zinc (Galvanized) Coating on Iron or Steel ArticlesASTM A240/A240M-04ae1 ? ? ? ? 压力容器用耐热铬及铬镍不锈钢板、薄板及带材? ? ? ? Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General ApplicationsASTM A242/A242M-04 ? ? ? ? 高强度低合金结构钢? ? ? ? Standard Specification for High-Strength Low-Alloy Structural SteelASTM A247-67(1998) ? ? ? ? 铁铸件中石墨显微结构评定试验方法? ? ? ? Standard Test Method for Evaluating the Microstructure of Graphite in Iron CastingsASTM A249/A249M-04 ? ? ? ? 锅炉、过热器、换热器和冷凝器用焊接奥氏体钢管? ? ? ? Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser TubesASTM A250/A250M-04 ? ? ? ? 锅炉和过热器用电阻焊铁素体合金钢管? ? ? ? Standard Specification for Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater TubesASTM A252-98(2002) ? ? ? ? 焊接钢和无缝钢管桩? ? ? ? Standard Specification for Welded and Seamless Steel Pipe PilesASTM A254-97(2002) ? ? ? ? 铜焊钢管规格? ? ? ? Standard Specification for Copper-Brazed Steel TubingASTM A255-02 ? ? ? ? 测定钢淬透性用末端淬火试验的标准试验方法? ? ? ? Standard Test Method for Determining Hardenability of SteelASTM A262-03 ? ? ? ? 奥氏体不锈钢晶间浸蚀敏感性的检测? ? ? ? Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless SteelsASTM A263-03 ? ? ? ? 耐腐蚀铬钢包覆板材,薄板材及带材技术规范? ? ? ? Standard Specification for Stainless Chromium Steel-Clad PlateASTM A264-03 ? ? ? ? 包覆的不锈铬镍钢板,薄板及带材规格? ? ? ? Specification for Stainless Chromium-Nickel Steel-Clad PlateASTM A265-03 ? ? ? ? 镍和镍基合金包覆钢板规格? ? ? ? Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel PlateASTM A266/A266M-03a ? ? ? ? 压力容器部件用碳素钢锻件规格? ? ? ? Standard Specification for Carbon Steel Forgings for Pressure Vessel ComponentsASTM A268/A268M-04 ? ? ? ? 一般设备用无缝和焊接铁素体与马氏体不锈钢管? ? ? ? Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General ServiceASTM A269-04 ? ? ? ? 一般设备用无缝和焊接奥氏体不锈钢管? ? ? ? Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General ServiceASTM A270-03a ? ? ? ? 卫生设施用无缝钢和焊接奥氏体不锈钢管? ? ? ? Standard Specification for Seamless and Welded Austenitic Stainless Steel Sanitary TubingASTM A275/A275M-98(2003) ? ? ? ? 钢锻件的磁粉检查试验方法? ? ? ? Standard Test Method for Magnetic Particle Examination of Steel ForgingsASTM A276-04 ? ? ? ? 不锈钢棒材和型材? ? ? ? Standard Specification for Stainless Steel Bars and ShapesASTM A278/A278M-01 ? ? ? ? 适用于650F容压部件用灰铸铁件的技术规范? ? ? ? Standard Specification for Gray Iron Castings for Pressure-Containing Parts for Temperatures Up to 650°F (350°C) ASTM A283/A283M-03 ? ? ? ? 低和中等抗拉强度碳素钢板? ? ? ? Standard Specification for Low and Intermediate Tensile Strength Carbon Steel PlatesASTM A285/A285M-03 ? ? ? ? 压力容器用低和中等抗拉强度的碳素钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile StrengthASTM A288-91(2003) ? ? ? ? 涡轮发电机磁性定位环用碳素钢和合金钢锻件? ? ? ? Standard Specification for Carbon and Alloy Steel Forgings for Magnetic Retaining Rings for Turbine Generators标准号? ? ? ? 标准中文名称? ? ? ? 标准英文名称ASTM A289/A289M-97(2003) ? ? ? ? 发电机非磁性定位环用合金钢锻件的技术规范? ? ? ? Standard Specification for Alloy Steel Forgings for Nonmagnetic Retaining Rings for GeneratorsASTM A290-02 ? ? ? ? 减速器环用碳素钢和合金钢锻件? ? ? ? Standard Specification for Carbon and Alloy Steel Forgings for Rings for Reduction GearsASTM A291-03 ? ? ? ? 减速器小齿轮、齿轮和心轴用碳素钢和合金钢锻件? ? ? ? Standard Specification for Steel Forgings, Carbon and Alloy, for Pinions, Gears and Shafts for Reduction Gears ASTM A295-98 ? ? ? ? 高碳耐磨轴承钢技术规范? ? ? ? Standard Specification for High-Carbon Anti-Friction Bearing SteelASTM A297/A297M-97(2003) ? ? ? ? 一般用耐热铬铁与镍铬铁合金钢铸件规格? ? ? ? Standard Specification for Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant, for General ApplicationASTM A299/A299M-04 ? ? ? ? 压力容器用锰硅碳钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-SiliconASTM A302/A302M-03 ? ? ? ? 压力容器用锰钼和锰钼镍合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel ASTM A304-04 ? ? ? ? 有末端淬火淬透性要求的合金钢棒材的技术规范? ? ? ? Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability RequirementsASTM A307-04 ? ? ? ? 抗拉强度为60000psi的碳素钢螺栓和螺柱的技术规范? ? ? ? Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile StrengthASTM A308/A308M-03 ? ? ? ? 经热浸处理镀有铅锡合金的薄板材的技术规范? ? ? ? Standard Specification for Steel Sheet, Terne (Lead-Tin Alloy) Coated by the Hot-Dip ProcessASTM A309-01 ? ? ? ? 用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法? ? ? ? Standard Test Method for Weight and Composition of Coating on Terne Sheet by the Triple-Spot TestASTM A311/A311M-04 ? ? ? ? 有机械性能要求的消除应力的冷拉碳素钢棒? ? ? ? Standard Specification for Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements ASTM A312/A312M-04a ? ? ? ? 无缝和焊接奥氏体不锈钢管? ? ? ? Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel PipesASTM A313/A313M-03 ? ? ? ? 不锈钢弹簧丝技术规范? ? ? ? Standard Specification for Stainless Steel Spring WireASTM A314-97(2002) ? ? ? ? 锻造用不锈及耐热钢坯及钢棒规格? ? ? ? Standard Specification for Stainless Steel Billets and Bars for ForgingASTM A319-71(2001) ? ? ? ? 高温无压部件用灰铁铸件? ? ? ? Standard Specification for Gray Iron Castings for Elevated Temperatures for Non-Pressure Containing PartsASTM A320/A320M-04 ? ? ? ? 低温用合金钢螺栓材料规格? ? ? ? Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for Low-Temperature ServiceASTM A321-90(2001) ? ? ? ? 经淬火和回火的碳素钢棒? ? ? ? Standard Specification for Steel Bars, Carbon, Quenched and TemperedASTM A322-91(2001)e1 ? ? ? ? 合金钢棒材.级别? ? ? ? Standard Specification for Steel Bars, Alloy, Standard GradesASTM A323-93(2000) ? ? ? ? 硼铁规格? ? ? ? Standard Specification for FerroboronASTM A324-73(2000) ? ? ? ? 钛铁合金? ? ? ? Standard Specification for FerrotitaniumASTM A325-04a ? ? ? ? 经热处理最小抗拉强度为120/105ksi的热处理钢结构螺栓? ? ? ? Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength ASTM A325M-04a ? ? ? ? 经热处理最小抗拉强度为830Mpa的热处理钢结构螺栓? ? ? ? Standard Specification for Structural Bolts, Steel, Heat Treated 830 Mpa Minimum Tensile Strength [Metric] ASTM A327-91(1997) ? ? ? ? 铸铁冲击试验方法? ? ? ? Standard Test Methods for Impact Testing of Cast IronsASTM A327M-91(1997) ? ? ? ? 铸铁冲击试验方法(米制)? ? ? ? Standard Test Methods for Impact Testing of Cast Irons (Metric)ASTM A328/A328M-03 ? ? ? ? 薄钢板桩? ? ? ? Standard Specification for Steel Sheet Piling ASTM A333/A333M-04a ? ? ? ? 低温用无缝与焊接钢管规格? ? ? ? Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature ServiceASTM A334/A334M-04a ? ? ? ? 低温设备用无缝与焊接碳素和合金钢管? ? ? ? Standard Specification for Seamless and Welded Carbon and Alloy-Steel Tubes for Low-Temperature ServiceASTM A335/A335M-03 ? ? ? ? 高温用无缝铁素体合金钢管? ? ? ? Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature ServiceASTM A336/A336M-03a ? ? ? ? 压力与高温部件用合金钢锻件规格? ? ? ? Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature PartsASTM A338-84(2004) ? ? ? ? 铁路,船舶和其他重型装备在温度达到650华氏度(345摄氏度)时使用的可锻铸铁法兰,管件和阀门零件? ? ? ? Standard Specification for Malleable Iron Flanges, Pipe Fittings, and Valve Parts for Railroad, Marine, and Other Heavy Duty Service at Temperatures Up to 650°F (345°C)ASTM A340-03a ? ? ? ? 有关磁性试验用符号和定义的术语? ? ? ? Standard Terminology of Symbols and Definitions Relating to Magnetic TestingASTM A341/A341M-00 ? ? ? ? 用直流磁导计和冲击试验法测定材料的直流磁性能的试验方法? ? ? ? Standard Test Method for Direct Current Magnetic Properties of Materials Using D-C Permeameters and the Ballistic Test MethodsASTM A342/A342M-99 ? ? ? ? 磁铁材料导磁率的试验方法? ? ? ? Standard Test Methods for Permeability of Feebly Magnetic MaterialsASTM A343/A343M-03 ? ? ? ? 在电力频率下用瓦特计-安培计-伏特计法(100-1000赫兹)和25 厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法? ? ? ? Standard Test Method forAlternating-Current Magnetic Properties of Materials at Power Frequencies UsingWattmeter-Ammeter-Voltmeter Method and 25-cm Epstein Test FrameASTM A345-98 ? ? ? ? 磁设备用平轧电炉钢? ? ? ? Standard Specification for Flat-Rolled Electrical Steels for Magnetic ApplicationsASTM A348/A348M-00 ? ? ? ? 用瓦特计--安培计--伏特计法(100-10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法? ? ? ? Standard Test Method for Alternating Current Magnetic Properties of Materials Using the Wattmeter-Ammeter-Voltmeter Method, 100 to 10 000 Hz and 25-cm Epstein FrameASTM A350/A350M-04 ? ? ? ? 要求进行缺口韧性试验的管道部件用碳素钢与低合金钢锻件技术规范? ? ? ? Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping ComponentsASTM A351/A351M-03 ? ? ? ? 容压零件用奥氏体及奥氏体铁素体铸铁的技术规范? ? ? ? Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing PartsASTM A352/A352M-03 ? ? ? ? 低温受压零件用铁素体和马氏体钢铸件规格? ? ? ? Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for Low-Temperature ServiceASTM A353/A353M-93(1999) ? ? ? ? 压力容器用经二次正火及回火处理的含9％镍的合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel,Double-Normalized and TemperedASTM A354-04 ? ? ? ? 淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格? ? ? ? Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded FastenersASTM A355-89(2000) ? ? ? ? 渗氮用合金钢棒? ? ? ? Standard Specification for Steel Bars, Alloys, for NitridingASTM A356/A356M-98(2003) ? ? ? ? 蒸汽轮机用厚壁碳素钢、低合金钢和不锈钢铸件? ? ? ? Standard Specification for Steel Castings, Carbon, Low Alloy, and Stainless Steel, Heavy-Walled for Steam TurbinesASTM A358/A358M-04 ? ? ? ? 高温用电熔焊奥氏体铬镍合金钢管? ? ? ? Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General ApplicationsASTM A363-03 ? ? ? ? 地面架空线用镀锌钢丝绳? ? ? ? Standard Specification for Zinc-Coated (Galvanized) Steel Overhead Ground Wire StrandASTM A367-60(1999) ? ? ? ? 铸铁的激冷试验方法? ? ? ? Standard Test Methods of Chill Testing of Cast IronASTM A368-95a(2000) ? ? ? ? 不锈钢和耐热钢丝绳的标准? ? ? ? Standard Specification for Stainless Steel Wire StrandASTM A369/A369M-02 ? ? ? ? 高温用锻制和镗孔碳素钢管和铁素体合金钢管? ? ? ? Standard Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature ServiceASTM A370-03a ? ? ? ? 钢制品机械测试的标准试验方法和定义? ? ? ? Standard Test Methods and Definitions for Mechanical Testing of Steel Products标准号? ? ? ? 标准中文名称? ? ? ? 标准英文名称ASTM A372/A372M-03 ? ? ? ? 薄壁压力容器用碳素钢及合金钢锻件? ? ? ? Standard Specification for Carbon and Alloy Steel Forgings for Thin-Walled Pressure VesselsASTM A376/A376M-02a ? ? ? ? 高温中心站用无缝奥氏钢管? ? ? ? Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Central-Station ServiceASTM A377-03 ? ? ? ? 球墨铸铁压力管规范索引? ? ? ? Standard Index of Specifications for Ductile-Iron Pressure PipeASTM A380-99e1 ? ? ? ? 不锈钢零件、设备和系统的清洗和除垢? ? ? ? Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and SystemsASTM A381-96(2001) ? ? ? ? 高压输送用金属弧焊钢管? ? ? ? Standard Specification forMetal-Arc-Welded Steel Pipe for Use With High-Pressure Transmission SystemsASTM A384/A384M-02 ? ? ? ? 防止钢组件热浸镀锌时翘曲和扭曲用安全保护? ? ? ? Standard Practice for Safeguarding Against Warpage and Distortion During Hot-Dip Galvanizing of Steel Assemblies ASTM A385-03 ? ? ? ? 提供高质量镀锌覆层(热浸)? ? ? ? Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip)ASTM A387/A387M-03 ? ? ? ? 压力容器用铬钼合金钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-MolybdenumASTM A388/A388M-03 ? ? ? ? 重型钢锻件超声波检测? ? ? ? Standard Practice for Ultrasonic Examination of Heavy Steel ForgingsASTM A389/A389M-03 ? ? ? ? 适合高温受压部件用经特殊热处理的合金钢铸件规格? ? ? ? Standard Specification for Steel Castings, Alloy, Specially Heat-Treated, for Pressure-Containing Parts, Suitable for High-Temperature ServiceASTM A390-95(2001) ? ? ? ? 饲养家禽用镀锌钢丝栏栅网(六角形和直线形)? ? ? ? Standard Specification for Zinc-Coated (Galvanized) Steel Poultry Fence Fabric (Hexagonal and Straight Line)ASTM A391/A391M-01 ? ? ? ? 80号合金钢链条? ? ? ? Standard Specification for Grade 80 Alloy Steel ChainASTM A392-03 ? ? ? ? 镀锌钢丝链环栏栅网? ? ? ? Standard Specification for Zinc-Coated Steel Chain-Link Fence FabricASTM A394-04 ? ? ? ? 传动塔架用镀锌和裸露钢螺栓? ? ? ? Standard Specification for Steel Transmission Tower Bolts, Zinc-Coated and BareASTM A395/A395M-99e1 ? ? ? ? 高温用铁素体球墨铸铁受压铸件? ? ? ? Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated TemperaturesASTM A400-69(2000) ? ? ? ? 钢棒的成分及机械性能选择指南? ? ? ? Standard Practice for Steel Bars, Selection Guide, Composition, and Mechanical PropertiesASTM A401/A401M-03 ? ? ? ? 铬硅合金钢丝? ? ? ? Standard Specification for Steel Wire, Chromium-Silicon AlloyASTM A403/A403M-04 ? ? ? ? 锻制奥氏体不锈钢管配件? ? ? ? Standard Specification for Wrought Austenitic Stainless Steel Piping FittingsASTM A407-93(2004) ? ? ? ? 盘簧用冷拉钢丝? ? ? ? Standard Specification for Steel Wire, Cold-Drawn, for Coiled-Type SpringsASTM A409/A409M-01 ? ? ? ? 腐蚀场所或高温下使用的焊接大口径奥氏体钢管? ? ? ? Standard Specification for Welded Large Diameter Austenitic Steel Pipe for Corrosive or High-Temperature ServiceASTM A411-03 ? ? ? ? 镀锌低碳钢铠装线? ? ? ? Standard Specification for Zinc-Coated (Galvanized) Low-Carbon Steel Armor WireASTM A413/A413M-01 ? ? ? ? 碳素钢链? ? ? ? Standard Specification for Carbon Steel Chain ASTM A414/A414M-04 ? ? ? ? 压力容器用碳素薄钢板? ? ? ? Standard Specification for Steel, Sheet, Carbon, for Pressure VesselsASTM A416/A416M-02 ? ? ? ? 预应力混凝土用无涂层七股钢铰线? ? ? ? Standard Specification for Steel Strand, Uncoated Seven-Wire for Prestressed ConcreteASTM A417-93(2004) ? ? ? ? 之字形、方形、正弦形家具用弹簧元件用冷拔钢丝? ? ? ? Standard Specification for Steel Wire, Cold-Drawn, for Zig-Zag, Square-Formed, and Sinuous-Type Upholstery Spring UnitsASTM A418-99(2003) ? ? ? ? 涡轮机及发电机钢转子锻件的超声波检查方法? ? ? ? Standard Test Method for Ultrasonic Examination of Turbine and Generator Steel Rotor ForgingsASTM A420/A420M-04 ? ? ? ? 低温下用锻制碳素钢和合金钢管配件? ? ? ? Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature ServiceASTM A421/A421M-02 ? ? ? ? 预应力混凝土用无涂层消除应力钢丝的技术规范? ? ? ? Standard Specification for Uncoated Stress-Relieved Steel Wire for Prestressed ConcreteASTM A423/A423M-95(2000) ? ? ? ? 无缝和电焊低合金钢管? ? ? ? Standard Specification for Seamless and Electric-Welded Low-Alloy Steel TubesASTM A424-00 ? ? ? ? 搪瓷用钢薄板? ? ? ? Standard Specification for Steel, Sheet, for Porcelain EnamelingASTM A426/A426M-02 ? ? ? ? 高温用离心铸造的铁素体合金钢管? ? ? ? Standard Specification for Centrifugally Cast Ferritic Alloy Steel Pipe for High-Temperature ServiceASTM A427-02 ? ? ? ? 冷轧和热轧用锻制合金钢辊? ? ? ? Standard Specification for Wrought Alloy Steel Rolls for Cold and Hot ReductionASTM A428/A428M-01 ? ? ? ? 钢铁制品上铝覆层重量的测试方法? ? ? ? Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel ArticlesASTM A434-04 ? ? ? ? 热轧与冷精轧经回火及淬火的合金钢棒? ? ? ? Standard Specification for Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and TemperedASTM A435/A435M-90(2001) ? ? ? ? 钢板的直射束纵向超声波检验? ? ? ? Standard Specification for Straight-Beam Ultrasonic Examination of Steel PlatesASTM A436-84(2001) ? ? ? ? 奥氏体灰口铁铸件? ? ? ? Standard Specification for Austenitic Gray Iron CastingsASTM A437/A437M-01a ? ? ? ? 高温用经特殊处理的涡轮型合金钢螺栓材料? ? ? ? Standard Specification for Alloy-Steel Turbine-Type Bolting Material Specially Heat Treated for High-Temperature ServiceASTM A439-83(1999) ? ? ? ? 奥氏体可锻铸铁铸件? ? ? ? Standard Specification for Austenitic Ductile Iron CastingsASTM A447/A447M-93(2003) ? ? ? ? 高温用镍铬铁合金钢铸件(25-12级)? ? ? ? Standard Specification for Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service ASTM A449-04a ? ? ? ? 经淬火和回火的钢螺栓和螺柱? ? ? ? Standard Specification for Quenched and Tempered Steel Bolts and StudsASTM A450/A450M-04 ? ? ? ? 碳素钢管、铁素体合金钢管及奥氏体合金钢管? ? ? ? Standard Specification for General Requirements for Carbon, Ferritic Alloy, and Austenitic Alloy Steel TubesASTM A451/A451M-02 ? ? ? ? 高温用离心铸造的奥氏体钢管? ? ? ? Standard Specification for Centrifugally Cast Austenitic Steel Pipe for High-Temperature ServiceASTM A453/A453M-03 ? ? ? ? 具有同奥氏体钢相类似的膨胀系数、屈服强度为50-120Ksi(345-827MPa)的耐高温螺栓材料? ? ? ? Standard Specification for High-Temperature Bolting Materials, with Expansion Coefficients Comparable to Austenitic Stainless SteelsASTM A455/A455M-03 ? ? ? ? 压力容器用高强度碳锰钢板? ? ? ? Standard Specification for Pressure Vessel Plates, Carbon Steel, High-Strength ManganeseASTM A456/A456M-99(2003) ? ? ? ? 大型曲轴锻件的磁粉检查? ? ? ? Standard Specification for Magnetic Particle Examination of Large Crankshaft ForgingsASTM A459-97(2003) ? ? ? ? 镀锌平轧扁钢铠装带? ? ? ? Standard Specification for Zinc-Coated Flat Steel Armoring TapeASTM A460-94(2004)e1 ? ? ? ? 包铜钢丝绳标准? ? ? ? Standard Specification for Copper-Clad Steel Wire StrandASTM A463/A463M-02a ? ? ? ? 热浸镀铝薄钢板? ? ? ? Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip ProcessASTM A466/A466M-01 ? ? ? ? 非焊接碳素钢链? ? ? ? Standard Specification for Weldless Chain ASTM A467/A467M-01 ? ? ? ? 机器链和盘旋链? ? ? ? Standard Specification for Machine and Coil Chain标准号? ? ? ? 标准中文名称? ? ? ? 标准英文名称。
ASTM标准号A B C
ASTM标准号A B CASTM A/B/C/D/E/F/G 2006年标准，只为索引无下载A3-01(2006) 低、中、高碳素钢鱼尾（连接）板A20/A20M-06 压力容器用钢板材通用要求A34/A34M-06 磁性材料的抽样和采购试验的标准惯例A49-01(2006) 经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板A53/A53M-06 无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范A74-06 铸铁污水管及配件的技术规范A106/A106M-06a 高温用无缝碳素钢管A135/A135M-06 电阻焊钢管A159-83(2006) 汽车用灰铁铸件A181/A181M-06 普通锻制碳素钢管的规格A182/A182M-06 高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件A184/A184M-06 混凝土加筋用变形钢筋编织网A185-06e1 钢筋混凝土用焊接钢丝结构A193/A193M-06a 高温设备用合金钢和不锈钢螺栓材料A194/A194M-06a 高温和高压设备用碳素钢与合金钢螺栓和螺母的规格A197/A197M-00(2006) 化铁炉用可锻铸铁A213/A213M-06ae1 无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管A227/A227M-06 机械弹簧用冷拉钢丝A234/A234M-06 中温与高温下使用的锻制碳素钢及合金钢管配件A240/A240M-06c 压力容器用耐热铬及铬镍不锈钢板、薄板及带材A275/A275M-06 钢锻件的磁粉检查试验方法A276-06 不锈钢棒材和型材A278/A278M-01(2006) 适用于650F容压部件用灰铸铁件的技术规范A312/A312M-06 无缝和焊接奥氏体不锈钢管A319-71(2006) 高温无压部件用灰铁铸件A322-06 合金钢棒材.级别A325-06 经热处理最小抗拉强度为120/105ksi的热处理钢结构螺栓A327-91(2006) 铸铁冲击试验方法A327M-91(2006) 铸铁冲击试验方法(米制)A335/A335M-06 高温用无缝铁素体合金钢管A336/A336M-06 压力与高温部件用合金钢锻件规格A351/A351M-06 容压零件用奥氏体及奥氏体铁素体铸铁的技术规范A352/A352M-06 低温受压零件用铁素体和马氏体钢铸件规格A355-89(2006) 渗氮用合金钢棒A369/A369M-06 高温用锻制和镗孔碳素钢管和铁素体合金钢管A370-06 钢制品机械测试的标准试验方法和定义A376/A376M-06 高温中心站用无缝奥氏钢管A380-06 不锈钢零件、设备和系统的清洗和除垢A387/A387M-06 压力容器用铬钼合金钢板A390-06 饲养家禽用镀锌钢丝栏栅网(六角形和直线形)A400-69(2006) 钢棒的成分及机械性能选择指南A403/A403M-06 锻制奥氏体不锈钢管配件A414/A414M-06 压力容器用碳素薄钢板A416/A416M-06 预应力混凝土用无涂层七股钢铰线A420/A420M-06 低温下用锻制碳素钢和合金钢管配件A424-06 搪瓷用钢薄板A434-06 热轧与冷精轧经回火及淬火的合金钢棒A436-84(2006) 奥氏体灰口铁铸件A437/A437M-06 高温用经特殊处理的涡轮型合金钢螺栓材料A451/A451M-06 高温用离心铸造的奥氏体钢管A466/A466M-01 非焊接碳素钢链A467/A467M-01(2006) 机器链和盘旋链A469/A469M-06 用于发电机转子的真空处理钢锻件A471-06 涡轮转子转盘和转轮用真空处理合金钢锻件技术规范A479/A479M-06a 锅炉及压力容器用不锈钢和耐热钢棒与型材A480/A480M-06a 扁平轧制耐热不锈钢厚板材、薄板材和带材通用要求A484/A484M-06a 不锈及耐热锻钢棒,钢坯及锻件的规格A488/A488M-06 钢铸件焊接规程和工作人员的合格鉴定A490-06 最小拉伸强度为150千磅/平方英寸热处理钢结构螺栓A495-06 硅钙合金钢技术规范A497/A497M-06e1 钢筋混凝土用焊接变形钢丝网A498-06 无缝与焊接碳素钢,铁素体钢与奥氏体钢制有整体散热片的换热器钢管A503/A503M-01(2006)e1 锻制大型曲轴的超声波检验A507-06 优质拉拔,热轧和冷轧合金钢薄板与带材A510-06 碳素钢盘条和粗圆钢丝通用要求A510M-06 碳素钢盘条和粗圆钢丝通用要求A512-06 冷拉对缝焊碳素钢机械管A513-06a 电阻焊碳素钢与合金钢机械钢管A516/A516M-06 中温及低温压力容器用碳素钢板A519-06 无缝碳素钢与合金钢机械管A522/A522M-06 低温用锻制或轧制含镍8%和9%的合金钢法兰,配件,阀门和零件规格A531/A531M-91(2006) 涡轮发电机钢定位环的超声波检验A537/A537M-06 压力容器用经热处理的碳锰硅钢板A540/A540M-06 特殊用途的合金钢螺栓材料A550-06 铌铁合金A553/A553M-06 压力容器用经回火和淬火的含8%及9%镍的合金钢板A562/A562M-06 搪玻璃或扩散金属镀层的压力容器用锰钛合金碳素钢板A563M-06 碳素钢及合金钢螺母技术规范（米制）A568/A568M-06a 热轧及冷轧高强度低合金碳素钢薄板A571/A571M-01(2006) 适用于低温压力容器零件的奥氏体球墨铸铁件A572/A572M-06 高强度低合金钴钒结构钢技术规范A576-90b(2006) 特级热轧碳素钢棒A580/A580M-06 耐热不锈钢丝A595/A595M-06 结构用圆锥形低碳钢管A608/A608M-06 高温受压离心铸造的铁铬镍高合金钢管A615/A615M-06a 钢筋混凝土配筋用变形和光面坯钢筋A623-06a 锡轧制产品A623M-06a 镀锡薄钢板轧制品通用要求(米制)A633/A633M-01(2006) 正火的高强度低合金结构钢A635/A635M-06a 热轧碳素钢薄板,带材和重型粗盘条规格A653/A653M-06 热浸处理的镀锌铁合金或镀锌合金薄钢板的标准规范A659/A659M-06 商业级热轧碳素钢薄板和带材(最大含碳量为0.16%-0.25%)A663/A663M-89(2006) 商品级碳素钢棒的机械特性A664-06 在ASTM规范中对电工钢和层压钢级别的识别A671-06 常温和较低温用电熔焊钢管A672-06 中温高压用电熔焊钢管A679/A679M-06 硬(冷)拉高抗拉强度钢丝A684/A684M-06 冷轧高碳钢带材A693-06 沉淀硬化耐热不锈钢板、薄板和带材A696-90a(2006) 压力管道部件专用热锻或冷精轧碳素钢棒A702-89(2006) 热锻钢栅栏柱和组件A703/A703M-06 受压部件用钢铸件A704/A704M-06 混凝土加筋用焊接普通钢棒或杆的光面钢筋或钢筋网A706/A706M-06a 混凝土配筋用变形低合金光面无节钢筋A709/A709M-06 桥梁用结构钢A717/A717M-06 单片样品表面绝缘电阻率的试验方法A722/A722M-06 预应力混凝土用无涂覆的高强度钢筋A729/A729M-06 货物运输及电气铁路用热处理合金钢轴A739-90a(2006) 升温或/和加压部件用热轧合金钢棒A743/A743M-06 一般用耐腐蚀铬铁及镍铬铁合金铸件A744/A744M-06 严酷条件下使用的耐腐蚀镍铬铁合金铸件A751-01(2006) 钢制品化学分析的实验方法、操作和术语A754/A754M-06 X射线荧光涂层厚度的试验方法A760/A760M-06 下水道和排水沟用金属涂覆的波纹钢管A774/A774M-06 低温和中温一般腐蚀情况下用的焊接锻制奥氏体不锈钢配件A775/A775M-06 涂环氧树脂的钢筋钢棒A781/A781M-06 一般工业用一般要求的钢和合金铸件A782/A782M-06 经淬火和回火的锰铬钼硅锆合金钢压力容器板A788/A788M-06 钢锻件A792/A792M-06 热浸工艺法处理的55%铝-锌合金涂覆钢板A796/A796M-06 雨水管和卫生污水管及其它地下埋设管道用波纹钢管、管托架及拱形架结构设计惯例A800/A800M-01(2006) 奥氏体合金钢铸件中铁素体含量的估算A802/A802M-95(2006) 钢铸件外观检验的表面验收标准A818-06 镀铜碳素钢丝A820/A820M-06 纤维增强混凝土用钢纤维A829/A829M-06 结构性合金钢板A830/A830M-06 按照化学成分要求提供的优质碳素钢板技术规范A832/A832M-06 压力容器板用铬钼钒及铬钼钒钛硼合金钢A834-95(2006) 一般工业用铁铸件的一般要求A837/A837M-06 渗碳用合金钢锻件A840/A840M-00(2006) 全处理的磁性夹层钢A848-01(2006) 低碳磁铁A858/A858M-06 低温和腐蚀情况下用热处理碳素钢配件A865-06 钢管连接用黑色或镀锌焊接或无缝钢螺纹接头A879/A879M-06 每面镀层质量应予标明的电解镀锌薄钢板A897/A897M-06 等温淬火球墨铸铁A900/A900M-01(2006) 非晶磁性带材叠装系数的测试方法A902-06 与金属涂覆的钢制品有关的标准技术术语A917-06a 要求每一面标识有镀层质量用的电解工艺涂层的薄钢板材标准规范A918-06 要求在每一面标识有涂层质量用电解工艺镀锌镍合金的薄钢板技术规范A923-06 检测锻制双重奥氏体/铁素体不锈钢中有害金属间相的标准试验方法A924/A924M-06 用热浸镀法对薄钢板金属涂层的一般要求的标准规范A932/A932M-01(2006) 用瓦特计-安培计-伏特计和薄钢板样品测试在电源频率下非晶体材料交流磁性能的标准试验方法A937/A937M-06 使用临界试验面测定绝缘涂层层间阻力的标准测试方法A939-96(2006) 圆柱体锻件镗孔表面反射超声检测的标准试验方法A940-06 涡轮转子用的差温热处理真空处理钢锻件,合金钢锻件的标准规范A941-06a 钢,不锈钢,有关合金和铁合金术语A945/A945M-06e1 为改良可焊接性、可加工性及粘接性用低碳限硫的高强度低合金结构钢板的标准规范A951/A951M-06 砌体接缝配筋的技术规范A955/A955M-06a 混凝土增强的变形的和无节钢筋技术规范A956-06 钢制品依阔提皮(Equotip)硬度测试方法A957/A957M-06 一般工业用普通要求熔模铸造的钢及合金钢熔模铸件技术规范A958-00(2006) 拉伸要求及化学要求类似于标准铸造等级的碳钢和合金钢铸件的技术规范A960/A960M-06 普通要求的锻制钢管管件的标准规范A962/A962M-06 预定用于从低温至蠕变范围内任何温度的钢紧固件或其材料的通用要求A965/A965M-06a 压力和高温零件用奥氏体钢锻件的技术规范A966/A966M-96(2006) 用交流电和磁粉探伤检验钢锻件的标准试验方法A970/A970M-06 混凝土配筋用焊接或锻制镦头的棒材技术规范A983/A983M-06 中速柴油发动机用连续晶粒流向锻制的碳素钢及合金钢曲轴技术规范A986/A986M-01(2006) 连续晶粒流向曲轴锻件的磁粉探伤检查技术规范A990-06 耐腐用保压零件用特殊控制阀的铁铬镍和铬合金铸件技术规范A992/A992M-06a 建筑框架中使用的结构成型件钢规范A996/A996M-06a 混凝土用条钢和车轴钢变形钢棒规范A1001-01(2006) 大型材高强度钢铸件规范A1008/A1008M-06a 高强度低合金和改性高强度低合金冷轧结构碳钢板材规范A1011/A1011M-06b 高强度低合金和改型高强度低合金热轧结构碳钢板材和带材规范A1014/A1014M-06 高温下使用的沉淀硬化螺栓连接材料规范(UNS N07718)A1017/A1017M-06 压力容器铬-钼-钨合金钢板规范A1018/A1018M-06c 含铌或钒的高强度低合金和改性高强度低合金热轧厚镀锡卷板结构碳钢板材和带材规范A1022/A1022M-06 用于混凝土加固的变形和未变形的不锈钢钢筋和焊接钢筋规范A1035/A1035M-06 用于混凝土加固的变形和未变形的低碳含铬棒材规范A1040-06 Standard Guide for Specifying Harmonized Standard Grade Compositions f or Wrought Carbon, Low-Alloy, and Alloy SteelsA1046/A1046M-06 Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip ProcessA1048/A1048M-06 Standard Specification for Pressure Vessel Forgings, Alloy Steel, High er Strength Chromium-Molybdenum-Tungsten for Elevated Temperature ServiceA1049/A1049M-06 Standard Specification for Stainless Steel Forgings, Ferritic/Austenitic(Duplex), for Pressure Vessels and Related ComponentsA1053/A1053M-06 Standard Specification for Welded Ferritic-Martensitic Stainless Steel PipeC10-06 Standard Specification for Natural CementC11-06 石膏及相关建材和系统相关术语C12-06 陶化粘土管线的安装C24-01(2006) 耐火和高矾土耐溶材料的溶锥当量测试法C25-06 石灰石,生石灰和熟石灰的化学分析方法C31/C31M-06 现场混凝土试样的制备和养护C43-06 结构用粘土制品的术语C51-06 与石灰及石灰石相关的(工业用)名词术语C59/C59M-00(2006) 石膏铸件和模型用灰泥C61/C61M-00(2006) 基恩(Keene)石膏水泥C67-06 砖及结构粘土瓦的取样和试验的试验方法C70-06 细集料表面湿度的测试方法C90-06a 承重混凝土空心砌块C94/C94M-06 搅拌好的混凝土规范C99-87(2006) 规格石料断裂模数的试验方法C110-06 生石灰,熟石灰和石灰石的物理试验方法C119-06 与规格石料相关的术语C120-06e1 石板的弯曲试验方法(弯曲模数和弹性模数)C121-06 石板吸水性的试验方法C125-06a 与混凝土和混凝土集料相关术语C131-06 用洛杉机磨耗试验机测定小规格粗集料的抗磨性与抗冲击性的试验方法C136-06 细集料及粗集料筛分试验方法C148-00(2006) 玻璃容器偏振检验的试验方法C157/C157M-06 硬化水泥灰浆和混凝土长度变化的试验方法C159-06 釉面陶瓷过滤块C170-06 天然建筑石料抗压强度的试验方法C174/C174M-06 混凝土钻心测量长度的试验方法C192/C192M-06 实验室中制造和养护混凝土的试验样品C207-06 砌筑用熟石灰C212-00(2006) 建筑用饰面瓷砖C216-06 饰面砖(粘土或页岩制实心砌块)C230/C230M-03 水硬性水泥试验用流动台C260-06 混凝土用加气混合物C265-06 水化硅酸盐水泥灰浆中的硫酸钙的试验方法C267-01(2006) 灰浆,薄浆和整块铺面石料耐化学侵蚀性的试验方法C270-06 砌块用的灰浆C273/C273M-06 夹层结构或夹层芯材的平直剪切性能的试验方法C305-06 塑性稠度的水硬性水泥泥浆和灰浆机械搅拌C309-06 养护混凝土用液态成膜化合物C315-06 粘土烟道衬砌料C323-56(2006) 卫生陶瓷粘土的化学分析的试验方法C329-88(2006) 焙烧卫生陶瓷材料比重的试验方法C341/C341M-06 水泥灰浆或混凝土的钻取试样和锯取试样长度变化的试验方法C359-06 硅酸盐水泥早硬的试验方法(灰浆法)C368-88(2006) 陶瓷器具抗冲击性的试验方法C370-88(2006) 焙烧卫生陶瓷制品受潮膨胀的试验方法C373-88(2006) 焙烧卫生陶瓷制品的吸水率、松密度、表观多孔性与表观比重的试验方法C375-58(2006) 搪瓷研磨用水的分类C387/C387M-06a 灰浆和混凝土用包装、烘干和复合材料C393/C393M-06 平夹层结构的挠曲试验方法C395-01(2006) 耐化学腐蚀的树脂灰浆C400-98(2006) 中和废酸用生石灰和熟石灰的试验方法C404-06 砌筑用灰浆集料C406-06 屋面石板瓦C408-88(2006) 卫生陶瓷制品传热性的试验方法C413-01(2006) 耐化学侵蚀的灰浆,薄浆和整块铺面石料吸收性的试验方法C424-93(2006) 用热压处理法测定焙烧卫生釉瓷抗破裂性的试验方法C428-05(2006) 石棉水泥无压污水管C448-88(2006) 工业瓷器茨漆的耐磨蚀的试验方法C452-06 暴露在硫酸盐中的硅酸盐水泥灰浆潜在膨胀性的试验方法C457-06 硬化混凝土中孔隙度和孔隙系统参数的显微测定的试验方法C458-98(2006) 石棉水泥制品中有机纤维含量的试验方法C459-97(2006) 石棉水泥板制品的试验方法C473-06 石膏板制品和石膏板条的物理测试标准试验方法C478-06b 预制钢筋混凝土检查井构件C478M-06b 预制钢筋混凝土检查井构件(米制)C500-98(2006) 石棉水泥管的试验方法C509-06 多孔弹性预成型垫片和密封材料C539-84(2006) 用干扰法测定搪瓷、釉瓷和白色陶瓷材料线性热膨胀的试验方法C541-98(2006) 石棉水泥管道的衬料C547-06 预制矿物纤维管形绝热材料C549-06 珠光岩疏松填充隔热材料C554-93(2006) 用热冲击法测定焙烧上釉卫生陶瓷器抗裂开的试验C578-06 刚性,蜂窝状聚苯乙烯的隔热C584-81(2006) 卫生陶瓷器具和有关制品的透光光泽度的试验方法C595-06 混合水硬性水泥C602-06 农用石灰处理材料C632-88(2006) 搪瓷用薄钢板的再煮倾向的试验方法C636/C636M-06 吸音瓦及铺设顶棚镶板用金属悬吊装置的安装C642-06 硬化混凝土的比重、吸收性及空隙度的试验方法C645-06 石膏板上无荷载(轴向)承载钢柱,滑槽(道)和硬性槽钢用的螺钉C661-06 用硬度计测量弹性密封件的压痕硬度的试验方法C665-06 木框架和轻型建筑物用矿质纤维毡绝热材料C674-88(2006) 卫生陶瓷材料的挠曲特性的试验方法C692-06 评定奥氏体钢热绝缘材料对外部应力腐蚀开裂趋势的影响的试验方法C694-90a(2006) 薄钢板在硫酸溶液浸渍过程中重量损失(质量损失)的试验方法C703-72(2006) 铝制搪瓷涂层的抗脱落试验方法C715-90(2006) 用光度计分析法测定搪瓷用钢表面沉积镍量的试验方法C716-06 安装锁条衬垫和固定上光材料C717-06 建筑用密封剂和密封料的术语C731-00(2006) 包装老化后胶乳密封料的可挤压性试验方法C732-06 人工风蚀对胶乳密封料老化效果的试验方法C734-06 胶乳密封料受人工气候影响后的低温柔韧性的试验方法C738-94(2006) 从上釉陶瓷表面提取铅和镉的试验方法C756-87(2006) 表面精整的清洁性试验方法C757-06 核纯级可烧结的二氧化钚粉末的规格C764-06 矿物纤维疏松填充热绝缘C773-88(2006) 预制封缝带泛油或增塑剂泛出的试验方法C774-88(2006) 焙烧的白色陶瓷材料抗压(压碎)强度的试验方法C778-06 玻璃上陶瓷装璜耐硫化物作用的试验方法C780-06 混凝土表面水平方向抗磨力的测试方法C787-06 浓缩用六氟化铀C794-06 弹性封缝料的抗撕裂粘附力的试验方法C810-90(2006) 用X射线光谱测定法测定搪瓷用钢制品表面镍沉积量的试验方法C822-06 混凝土管及其有关制品的术语C825-06 预制混凝土栅栏C830-00(2006) 用真空压力法测定耐火砖和异型砖的表观多孔性、吸水性、表观比重和体密度的试验方法C835-01(2006) 20-1400℃表面整个半球辐射热的测试方法C836-06 分层磨损层用的高固体含量冷却液体用弹性防水薄膜C840-06 石膏板的加工和应用C843-99(2006) 石膏砌面粉饰的应用C848-88(2006) 用共振法测定卫生陶瓷的弹性模量、切变模量和泊松比的试验方法C849-88(2006) 卫生陶瓷努氏压痕硬度的试验方法C864-05 致密弹性压缩密封垫片，调整垫块和定位块技术规范C866-77(2006) 卫生陶瓷粘土的过滤速率的测试方法C869-91(2006) 泡沫混凝土用生产预制泡沫材料用发泡剂C880-06 天然建筑石料弯曲强度的试验方法C889-06 核纯级的氧化钆(Gd2O3)粉末规格C890-06 整体或分段预制混凝土贮水及废水建筑物的最低结构设计负载的推荐规程C902-06 行人及交通不繁忙的道路用铺面砖C904-01(2006) 耐化学腐蚀的非金属材料的术语C905-01(2006) 耐化学的灰浆、薄胶泥和整体面层的表观密度的试验方法C908-00(2006) 预制密封带的屈服强度的试验方法C910-06 单一成份弹性溶剂释放型密封料的粘结力及粘聚力的试验方法C926-06 硅酸盐水泥基灰浆的应用C932-06 室外粉刷表面用粘结剂C933-05 焊丝板条C953-06 在实验室内测定预置集料混凝土的灌浆料凝固时间的试验方法C955-06 螺钉安装石膏板及金属灰泥基板用承载(横向及轴向)钢墙骨、导板、系杆或隔栅撑C957-06 与整体磨损层一同使用的冷却液用含大量固体物质的弹性防水薄膜C961-06 热用密封材料的搭接剪切强度的试验方法C968-06 烧结氧化钆及二氧化铀丸粒的分析方法C970-87(2006) 多个容器堆中专用核材料取样C972-00(2006) 密封带的压缩恢复的试验方法C989-06 混凝土和灰浆用研磨成颗粒状的高炉碎渣的技术规范C990-06 使用预制接缝密封胶粘结的混凝土管道、检查孔和预制箱型型件C990M-06 使用预制接缝密封胶粘结混凝土管道、检查孔和预制箱形件C992-06 核废燃料存放架用系列硼基中子吸收材料设备C1009-06 核工业化学分析实验室制订质量保证大纲C1015-06 纤维素和矿物纤维松充填热绝缘装置C1028-06 用水平功率拉力计法估价瓷砖及其它相同表面的磨擦电系数的试验方法C1032-06 钢丝网抹灰底层C1043-06 使用护热板装置中线电源加热器时稳态热传导特性测量用的加热板温度的测定C1072-06 砌块抗弯粘结强度的测定C1077-06 建筑用混凝土和混凝土集料的实验室测试标准惯例和实验室评定准则C1083-06 弹性泡沫垫圈和密封材料吸水性的试验方法C1088-06 粘土或泥板岩制薄陶面砖C1089-06 离心铸造的预应力混凝土C1093-06 砌块试验方法的鉴定C1094-01(2006) 可移动的挠性绝热覆盖物C1097-06 沥青混凝土混合物用熟石灰C1104/C1104M-00(2006) 测定未覆面矿物纤维绝缘材料蒸汽的吸收率的试验方法C1108-99(2006) 控制电势库仑法测定钚的试验方法C1114-00(2006) 薄加热设备稳态热传导特性的试验方法C1115-06 密实弹性体硅橡胶衬垫和附件C1120-98(2006) 石棉清洗试验方法C1136-06 热绝缘材料用柔性、低渗透蒸汽阻化剂C1141-06 喷浆混凝土用添加剂C1145-06 高级陶瓷术语C1154-06 石棉水泥和纤维水泥术语C1166-06 致密及多孔弹性体衬垫和附件火焰蔓延的试验方法C1170-06 使用振动台测定滚动压实混凝土的稠度和密度的试验方法C1173-06 地下管道系统用挠性过渡管联接件C1177/C1177M-06 用于遮敝的玻璃衬垫石膏基层C1210-06 制定核工业分析化学实验室用测量系统质量控制大纲C1215-92(2006) 核工业用试验方法标准中精密度与及偏倚报告的编写和表达C1217-00(2006) 处理核材料及放射性材料用设备的设计C1222-06 实验室试验水硬水泥的评定C1226-93(2006) 石棉中可溶氯化物的试验方法C1239-06a 报告单轴强度数据和评估高级陶瓷维泊尔分布参数C1245/C1245M-06 测定路碾水硬性压缩混凝土与其它水硬性水泥混合物结合强度的标准试验方法-点负荷试验C1248-06 用连接密封层时多孔衬底染色的标准试验方法C1249-06a 结构件密封剂上光泽用的密封隔热玻璃装置二次密封指南C1257-06 溶剂释放型密封剂加速老化的标准试验方法C1267-06 近距预演金属探测器操作灵敏度设置调整的标准规程C1271-99(2006) 石灰和石灰岩X射线光谱分析标准试验方法C1274-00(2006) 用物理吸收法对高级陶瓷比表面积的标准试验方法C1277-06 防护联接器连接无毂铸铁污水管和配件标准规范C1278/C1278M-06 增强纤维石膏镶板标准规范C1282-00(2006) 用离心光电沉淀法测定高级陶瓷粒径分布的标准试验方法C1283-06 安装粘土烟道衬块的标准操作规范C1289-06 贴面硬质泡沫聚异氰尿酸酯隔热板的标准规范C1290-06 外部隔热HVAC导管用的软玻璃纤维地毯隔热材料的标准规范C1293-06 用测定碱-硅石反应引起的混凝土长度变化对混凝土集料的标准试验方法C1305-06 液体外加防水薄膜的裂缝挖补能力的标准测定方法C1315-06 固化混凝土和密封混凝土液膜性化合物特种性能的标准规范C1341-06 连续纤维增强高级陶瓷合成物弯曲特性的标准试验方法C1355/C1355M-96(2006) 玻璃纤维增强的石膏组合件的技术规范C1364-06 建筑铸石的标准规范C1367-06 最大承载剪切下热应用密封剂的标准试验方法C1368-06 在环境温度下加恒定应力弯曲试验测定整体高级陶瓷裂纹缓慢增长参数的标准试验方法C1384-06a 砌筑用砂浆改性剂技术规范C1393-00a(2006) 管道和罐绝热用的垂直导向矿物质纤维包裹物和覆盖物规范C1396/C1396M-06 石膏灰泥屋顶板规范C1433M-06 涵洞，雨水排放管道和污水管道用的预浇筑加强混凝土箱型制件规范（米制）C1433-06 涵洞，雨水排放管道和污水管道用的预浇筑加强混凝土箱型制件规范C1435/C1435M-06 用震动锤在桶型模具中模压制作滚轮压缩的混凝土标准惯例C1442-06 用人工风化仪器对密封剂进行试验标准惯例C1452-00(2006) 高压加气增强混凝土构件规范C1453-00(2006) 用核级二氧化铀粉末和颗粒点火及氧铀(O/U)原子比法测定铀的试验方法C1461-06 地下和地上用接合排水、废物、通风、污水、卫生及暴雨排放系统用带热塑弹性垫圈的机械连接器的规范C1464-06 弯曲玻璃规范C1465-00(2006) 高温下用恒定应力速度挠曲试验测定高级陶瓷的慢裂增长系数的标准试验方法C1467/C1467M-00(2006) 模制玻璃纤维增强石膏部件安装规范C1468-06 室温下连续纤维增强高级陶瓷过渡厚度抗拉强度试验方法C1470-06 高级陶瓷热性能测试指南C1472-06 确定密封材料接缝宽度时计算运动和其它影响因素的标准指南C1474-00(2006)e1 四极感应耦合等离子质谱法分析核纯级燃料中铀的同位素组分的试验方法C1476-06 感应耦合等离子质谱法分析尿液中锝99试验方法C1477-06 多收集器感应耦合等离子质谱法分析六氟化铀同位素丰度的标准试验方法C1478-06 钢筋混凝土雨水排水结构、管道和支管之间的雨管水道弹性连接件规范C1478M-03(2006) 钢筋混凝土雨水排水结构、管道和支管之间的雨管水道弹性连接件规范(米制）C1481-00(2006) 外部绝缘和精整系统用密接剂使用的标准指南C1485-06 用电辐射热能量源测量露天阁楼地板绝缘材料临界辐射通量的测试方法C1495-06 表面研磨对高级陶瓷抗弯强度影响试验方法C1507-01(2006) 土壤中锶-90放射化学测定的试验方法C1508-01(2006) 用X射线荧光光谱法测定UF-6和硝酸铀酰中溴和氯的含量的标准试验方法C1529-06 生石灰、熟石灰和石灰石的环境用途规范C1532-06 从现有建筑选择，移动，装运石工装配样品指南C1577-06 Standard Specification for Precast Reinforced Concrete Box Sections fo r Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFDC1579-06 Standard Test Method for Evaluating Plastic Shrinkage Cracking of Res trained Fiber Reinforced Concrete (Using a Steel Form Insert)C1587-06 Standard Practice for Preparation of Field Removed Manufactured Masonr y Units and Masonry Specimens for Compressive Strength TestingC1601-06 Standard Test Method for Field Determination of Water Penetration ofMasonry Wall SurfacesC1602/C1602M-06 Standard Specification for Mixing Water Used in the Production of Hy draulic Cement ConcreteC1607-06 Standard Test Method for Determination of "Microwave Safe for Reheati ng" for CeramicwareC1608-06 Standard Test Method for Chemical Shrinkage of Hydraulic Cement Paste C1610/C1610M-06 Standard Test Method for Static Segregation of Self-Consolidating Concrete Using Column TechniqueC1621/C1621M-06 Standard Test Method for Passing Ability of Self-Consolidating Concrete by J-RingC1630-06 Standard Guide for Development of Coverage Charts for Loose-Fill Thermal Building InsulationsC1635-06 Standard Test Method to Evaluate Adhesion/Cohesion Properties of a Se alant at Fixed ExtensionC1636-06a Standard Guide for the Determination of Uranium-232 in Uranium HexafluorideC1637-06 Standard Test Method for the Determination of Impurities in PlutoniumMetal: Acid Digestion and Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS) AnalysisC1638-06 Standard Guide for the Determination of Iodine-129 In Uranium OxideC1644-06 Standard Specification for Resilient Connectors Between Reinforced Conc rete On-Site Wastewater Tanks and PipesC1645-06 Standard Test Method for Freeze-thaw and De-icing Salt Durability of Solid Concrete Interlocking Paving UnitsC1647-06 Standard Practice for Removal of Uranium or Plutonium, or both, forImpurity Assay in Uranium or Plutonium Materials特别声明：1：资料来源于互联网，版权归属原作者2：资料内容属于网络意见，与本账号立场无关3：如有侵权，请告知，立即删除。
3600个 ASTM 标准目录清单
ASTM A系列标准ASTM A100－2004 硅铁ASTM A1011－2006 高强度低合金和改型高强度低合金热轧结构碳钢板材和带材规范ASTM A1011－A1011M－2006b 高强度低合金和改型高强度低合金热轧结构碳钢板材和带材规范ASTM A101－2004 铬铁ASTM A1017－2005 压力容器铬－钼－钨合金钢板规范ASTM A1018－A1018M－2006b含铌或钒的高强度低合金和改性高强度低合金热轧厚镀锡卷板结构碳钢板材和带材规范ASTM A102－2004 钒铁合金ASTM A1035－A1035M－2006 用于混凝土加固的变形和未变形的低碳含铬棒材规范ASTM A105&A105M－2002 管道用碳素钢锻件标准规范ASTM A105－1998 管道部件用碳素钢锻件ASTM A105－A105M－2003 管系部件用碳素钢锻件ASTM A106－1999 高温设备用无缝碳素钢管的标准规范ASTM A106－A106M－2004a 高温用无缝碳素钢管ASTM A106－A106M－2006 高温用无缝碳素钢管ASTM A108－2003 优质冷加工碳素钢棒材技术规范ASTM A109－A109M－2003 冷轧碳素钢带技术规范ASTM A111－99a(2004)e1 电话和电报线路用镀锌－铁－丝规格ASTM A116－2000 镀锌钢丝编织栏栅网ASTM A1－2001 碳素钢丁字轨ASTM A121－99(2004) 镀锌刺钢丝ASTM A123&A123M－2001a 铁和钢制品镀锌层(热浸镀锌)的标准规范ASTM A135－A135M－2006 电阻焊钢管ASTM A143－2001 热浸镀锌结构钢制品防脆化的标准实施规程和脆化探测方法ASTM A148－2001 结构用高强度钢铸件ASTM A148A148M－2001 结构用高强度钢铸件ASTM A153&A153M－2001a 铁及钢制金属构件上镀锌层(热浸)标准规范ASTM A153－2003 钢铁制金属构件上镀锌层(热浸)的标准规范ASTM A181－2001 普通锻制碳素钢管的规格ASTM A182－2002 高温下使用的锻制或轧制的合金钢管法兰、锻制管件、阀门及零件的标准规范ASTM A182－A182M－2006 高温设备用锻制或轧制的合金钢管法兰、锻制管件、阀门及零件ASTM A184－A184M－2006 混凝土加筋用变形钢筋编织网ASTM A193－2000 高温设备用合金钢和不锈钢螺栓材料的标准规范ASTM A193－A193M－2006 高温设备用合金钢和不锈钢螺栓材料ASTM A194－A194M－2006 高温和高压设备用碳素钢与合金钢螺栓和螺母的规格ASTM A197－A197M－2000(2006) 化铁炉用可锻铸铁ASTM A202－2003 压力容器用铬锰硅合金钢板ASTM A202－202M－2003 压力容器用铬锰硅合金钢板ASTM A20A20M－2001 压力容器用钢板材通用要求ASTM A20－A20M－2006 压力容器用钢板材通用要求ASTM A213－2001 无缝铁素体和奥氏体合金钢锅炉、过热器和热交换器管的标准规范ASTM A213－A213M－2006 无缝铁素体和奥氏体合金钢锅炉、过热器和换热器管ASTM A2－2002 普通型,带槽和防护型碳素工字钢轨ASTM A225－A225M－2003 压力容器用锰矾镍合金钢板ASTM A227－A227M－1999 机械弹簧用冷拉钢丝ASTM A227－A227M－2006 机械弹簧用冷拉钢丝ASTM A228－1993 乐器用优质弹簧钢丝标准规范ASTM A234&A234M－2000a 中温与高温设备用锻制碳素钢及合金钢管配件的标准规范ASTM A234&A234M－2005 中温与高温设备用锻制碳素钢及合金钢管配件的标准规范ASTM A239－1995(2004) 用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法ASTM A239－2004 用普力斯试验法(硫酸铜浸蚀)确定铁或钢制品上镀锌层最薄点的测试方法ASTM A240－1994 压力容器用耐热铬及铬镍不锈钢板、薄板及带材ASTM A240－2004a 压力容器用耐热铬及铬镍不锈钢板、薄板及带材ASTM A249－2001 锅炉焊接管ASTM A262－2002ae2 奥氏体不锈钢晶间浸蚀敏感性的检测ASTM A266&A266M－2003 压力容器部件用碳素钢锻件标准规范ASTM A268&A268M－20001 通用无缝和焊接铁素体与马氏体不锈钢管的标准规范ASTM A269－2001 普通设备用无缝和焊接奥氏体不锈钢管标准规范ASTM A27－1995 通用碳素钢铸件ASTM A276－2006 不锈钢棒材和型材1ASTM A27A27M－2000 通用碳素钢铸件ASTM A283A&283M－1998 低和中等抗拉强度碳素钢板标准规范ASTM A290－1995 减速器环用碳素钢和合金钢锻件ASTM A295－2005 高碳耐磨轴承钢技术规范ASTM A29－A29M－1999 热锻及冷加工碳素钢和合金钢棒ASTM A307－2000 抗拉强度为60000PSI的碳素钢螺栓和螺柱的标准规范ASTM A308－2003 经热浸处理镀有铅锡合金的薄板材的技术规范ASTM A309－2001 用三点试验法测定长镀锌薄钢板镀层的重量成分的试验方法ASTM A311－2000 有机械性能要求的消除应力的冷拉碳素钢棒ASTM A312&A312M－2001a 无缝、焊接和深度冷加工奥氏体不锈钢管的标准规范ASTM A31－2004 钢铆钉及铆钉和压力容器用棒材ASTM A312－A312M－2006 无缝和焊接奥氏体不锈钢管ASTM A3－2001(2006) 低、中、高碳素钢鱼尾（连接）板ASTM A320－A320M－2005 低温用合金钢螺栓材料规格ASTM A325M－2000 最小抗拉强度为830Mpa的热处理钢结构螺栓标准规范(米制)ASTM A327M－1991(2006) 铸铁冲击试验方法(米制)ASTM A333&A333M－1999 低温设备用无缝和焊接钢管的标准规范ASTM A333－2004 低温设备用无缝和焊接钢管的标准规范ASTM A335－A335M－2006 高温用无缝铁素体合金钢管ASTM A336－A336M－2006 压力与高温部件用合金钢锻件规格ASTM A338－1994(2004)铁路、船舶和其它重负荷设施在650F（345℃）温度内使用的可锻铸铁法兰、管道配件和阀门零件ASTM A340－2003a 有关磁性试验用符号和定义的术语ASTM A343－2003在电力频率下用瓦特计－安培计－伏特计法(100－1000赫兹)和25厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法ASTM A343－343M－2003在电力频率下用瓦特计－安培计－伏特计法(100－1000赫兹)和25厘米艾普斯亭(EPSTEIN) 机架测定材料的交流电磁性能的试验方法ASTM A345－2004 磁设备用平轧电炉钢ASTM A348－2005用瓦特计－安培计－伏特计法(100－10000赫兹)和25厘米艾普斯亭框测定材料的交流磁性能的试验方法ASTM A34－A34M－2001 磁性材料的抽样和采购试验的标准惯例ASTM A351A315M－2000 压力容器部件用奥氏体和双相奥氏体－铁素体铸件ASTM A351－A351M－2006 容压零件用奥氏体及奥氏体铁素体铸铁的技术规范ASTM A354－2004 淬火与回火合金钢螺栓,双头螺栓及其他外螺纹紧固件规格ASTM A36&A36M－1996 结构碳钢的标准规范ASTM A366e1－1997 冷轧碳钢规范ASTM A370－1996 钢制品机械试验的标准试验方法和定义(中文版)ASTM A370－2003a 钢制品机械试验的标准试验方法和定义ASTM A380－1999(2005) 不锈钢零件、设备和系统的清洗和除垢ASTM A384－2005ASTM A385－2005 提供高质量镀锌覆层(热浸)ASTM A400－69(2006) 钢棒的成分及机械性能选择指南ASTM A403－1997 锻制奥氏体管不锈钢配件标准规范ASTM A403－A403M－2006 锻制奥氏体不锈钢管配件ASTM A409－409M－2001 腐蚀场所或高温下使用的焊接大口径奥氏体钢管ASTM A416－A416M－2006 预应力混凝土用无涂层七股钢铰线ASTM A421 A421M－2005 预应力混凝土用无涂层消除应力钢丝的技术规范ASTM A421－2002 预应力混凝土用无涂层消除应力钢丝的技术规范ASTM A437A&437M－2004 高温设备用经特殊热处理的涡轮型合金钢螺栓材料标准规范ASTM A451－A451M－2006 高温用离心铸造的奥氏体钢管ASTM A47－A47M－1999 铁素体可锻铁铸件ASTM A485－2003 高淬透性耐磨轴承钢的技术规ASTM A48－A48M－2003 灰铁铸件ASTM A49－2001 经热处理的碳素钢鱼尾（连接）板，微合金鱼尾板及锻制碳素钢异型鱼尾板ASTM A494－2004 镍和镍合金铸件ASTM A496－2001 混凝土增强用变形钢丝的标准规范ASTM A512－96 （2001）冷拉对缝焊碳素钢机械管规格标准ASTM A513－2000 电阻焊碳素钢与合金钢机械钢管标准规范ASTM A513－2006 电阻焊碳素钢与合金钢机械钢管ASTM A514M－2000a焊接用经回火与淬火的高屈服强度合金钢板ASTM A514M－2005 焊接用经回火与淬火的高屈服强度合金钢板ASTM A516－A516M－2006 中温及低温压力容器用碳素钢板ASTM A517－2006 压力容器用经回火与淬火的高强度合金钢板ASTM A518–2003 耐蚀高硅铁铸件ASTM A524－1996(2001) 常温和低温用无缝碳素钢管ASTM A530A530M－2004a 特种碳素钢和合金钢管ASTM A532 A532M－1993a(2003) 耐磨铸铁ASTM A53－2002 黑色和热浸镀锌焊接及无缝钢管规范ASTM A53－2006 无镀层热浸的、镀锌的、焊接的及无缝钢管的技术规范ASTM A536－1984(2004) 球墨铸铁件中文版ASTM A537－A537M－2006 压力容器用经热处理的碳锰硅钢板ASTM A540－A540M－2006 特殊用途的合金钢螺栓材料ASTM A541 A541M－2005 压力容器部件用经淬火和回火的碳素钢及合金钢锻件ASTM A553A&553M－1995(00) 压力容器用经回火和淬火的含8%及9%镍的合金钢板的标准规范ASTM A563M－2003 碳合金钢螺母ASTM A564－2004 热轧及冷精轧时效硬化处理过的不锈钢棒材和型材技术规范ASTM A568－A568M－2006 热轧及冷轧高强度低合金碳素钢薄板ASTM A572－2006 高强度低合金钴钒结构钢技术规范ASTM A572－A572M－2006 高强度低合金钴钒结构钢技术规范ASTM A575－1996(2002) 商品级碳素钢棒(M级)ASTM A577 A577M－1990(2001) 钢板的超声角波束检验ASTM A578 A578M－1996(2001) 特殊设备用的普通钢板和包覆钢板的直波束超声探伤检验ASTM A578A578M－2001 特殊设备用的普通钢板和包覆钢板的直波束超声探伤检验的标准规范ASTM A579－2004 超高强度合金钢锻件ASTM A580 A580M－1998 耐热不锈钢丝ASTM A581 A581M－1995b(2000) 高速切削用耐热不锈钢丝和盘条ASTM A581A581M－1995b(2004) 高速切削用耐热不锈钢丝和盘条ASTM A582 A582M－2005 热轧或冷精轧的高速切削不锈及耐热钢棒ASTM A586－1998 镀锌平行和螺旋形钢丝绳ASTM A587－1996(2001) 化学工业用电阻焊低碳钢管ASTM A588 A588M－2004 高强度低合金结构钢4英寸(100mm)厚屈服点最小为50ksi(345MPa) ASTM A589 A589M－2006 水井用无缝和焊接碳素钢管ASTM A6&A6M－1989 轧制结构钢棒材、板材、型材和板桩一般要求的标准规范ASTM A606,656715,JIS G3106,3114中文ASTM A615－A615M－2006 钢筋混凝土配筋用变形和光面坯钢筋ASTM A6－2000 轧制结构钢棒材、板材、型材和板桩一般要求的标准规范ASTM A6－2004 轧制结构钢棒材、板材、型材和板桩一般要求的标准规范(中文)ASTM A633－A633M－2001(2006) 正火的高强度低合金结构钢ASTM A644－1998(R2003) 铁铸件的相关术语ASTM A65－2001 钢轨道钉ASTM A653－A653M－2006 热浸处理的镀锌铁合金或镀锌合金薄钢板的标准规范ASTM A656－2003 具有改良可模锻性的高强度低合金热轧结构钢板ASTM A66－2001 钢质螺旋道钉ASTM A663－A663M－1989(2006) 商品级碳素钢棒的机械特性ASTM A666－奥氏体不锈钢板ASTM A67－2000 热加工低碳钢和高碳钢垫板技术规范ASTM A691－1998(2002) 高温下高压装置用电熔焊碳素钢和合金钢管ASTM A696－2000 压力管道部件专用热锻或冷精轧碳素钢棒ASTM A6－A6M－2006 轧制结构钢板材、型材和薄板桩通用技术要求ASTM A703－2004a 受压部件用钢铸件ASTM A704－A704M－2006 混凝土加筋用焊接普通钢棒或杆的光面钢筋或钢筋网ASTM A706－2006a 混凝土配筋用低合金变形和光圆钢筋ASTM A706－A706M－2006 混凝土配筋用变形低合金光面无节钢筋ASTM A707－2002 低温设备用锻制碳素钢和合金钢法兰ASTM A709－A709M－2006 桥梁用结构钢ASTM A722A&722M－1998 预应力混凝土用未涂覆的高强度钢棒材的标准规范ASTM A732－2002 一般设备用熔模铸造碳素低合金钢及高强度加温钴合金钢铸件ASTM A732A732M－2002 一般设备用熔模铸造碳素低合金钢及高强度加温钴合金钢铸件ASTM A737－1999(2004) 高强度低合金钢压力容器板ASTM A74－2004 铸铁污水管及配件的技术规范ASTM A743A743M－2003 一般用途铁铬、铁铬镍耐腐蚀铸件ASTM A748－1987 压力容器用静态铸造的激冷白口铁－灰口铁双金属轧辊ASTM A754－A754M－2006 X射线荧光涂层厚度的试验方法ASTM A763－2004 铁素体不锈钢晶间腐蚀敏感性检测ASTM A775－A775M－2006 涂环氧树脂的钢筋钢棒ASTM A781－2002 一般工业用一般要求的钢和合金铸件ASTM A781A781M－2002 一般工业用一般要求的钢和合金铸件ASTM A782－A782M－1990[1996] 经淬火和回火的锰铬钼硅锆合金钢压力容器板ASTM A782－A782M－2006 经淬火和回火的锰铬钼硅锆合金钢压力容器板ASTM A795M－2004 防火用黑色及热浸镀锌的焊接和无缝钢管ASTM A796－A796M－2006雨水管和卫生污水管及其它地下埋设管道用波纹钢管、管托架及拱形架结构设计惯例ASTM A800－A800M－2001(2006) 奥氏体合金钢铸件中铁素体含量的估算ASTM A802－A802M－1995(2006) 钢铸件外观检验的表面验收标准ASTM A810－2001 镀锌钢管用绕网ASTM A815－2004 锻制铁素体、铁素体奥氏体和马氏体不锈钢管配件ASTM A817－2003 链接栅栏网用金属涂覆钢丝ASTM A820－A820M－2006 纤维增强混凝土用钢纤维ASTM A82－2002 钢筋混凝土用无节钢丝ASTM A832－1995 压力容器板用铬钼钒及铬钼钒钛硼合金钢ASTM A836－1995 搪瓷管和压力容器设备用钛稳定碳素体钢锻件ASTM A841－2001 压力容器用温度机械控制工艺加工的钢板ASTM A844A844M－1993(1999) 压力容器用直接淬火加工的含镍9%的合金钢板ASTM A887－1989(2004) 核能设备用经硼酸处理的不锈钢板、薄板及带材ASTM A897－A897M－2006 等温淬火球墨铸铁ASTM A90&A90M－2001 镀锌和镀锌合金钢铁制品镀层重量的标准试验方法ASTM A905－1993 压力容器缠绕用钢丝ASTM A917－2006 要求每一面标识有镀层质量用的电解工艺涂层的薄钢板材标准规范ASTM A923－2006 检测锻制双重奥氏体－铁素体不锈钢中有害金属间相的标准试验方法ASTM A946－1995 耐腐蚀和耐热用铬,铬－镍和硅合金钢板,薄板和带的标准规范ASTM A955－A955M－2006a 混凝土增强的变形的和无节钢筋技术规范ASTM A960－A960－2003 普通要求的锻制钢管管件的标准规范ASTM A967－2001 不锈钢零件化学钝化处理的标准规范ASTM A99－2003 锰铁合金ASTM A996－A996M－2006a 混凝土用条钢和车轴钢变形钢棒规范ASTM B 系列标准ASTM B103－1998 锡磷青铜板带材标准ASTM B117－2003 盐雾喷射（雾化）装置操作的标准实施规范 (中文版)ASTM B117－2003 盐雾喷射（雾化）装置操作的标准实施规范(EN)ASTM B117－2003 盐雾喷射装置操作的标准实施规范ASTM B137－1995 阳极镀铝层重量测定的标准试验方法ASTM B148－1997(2003) 铝青铜砂型铸件ASTM B152－152M－2000 铜薄板、带材、中厚板及轧制棒材技术规范ASTM B152M－2006 铜薄板、带材、中厚板及轧制棒材技术规范ASTM B16&B16M－2000 螺纹切削机用易切削黄铜杆材、棒材和型材的标准规范ASTM B16－2005 制螺钉机用易切削黄铜条材、棒材和型材ASTM B164－1998 镍铜合金杆材、棒材和线材标准规范ASTM B166－2004 镍铬铁合金及镍铬钴钼合金条材、棒材及线材ASTM B167－2001 无缝镍铬铁合金管ASTM B168－2001 镍铬铁合金及镍铬钴钼合金板、薄板和带材ASTM B179－2006 砂型铸件、永久型模铸件和压模铸件用铝合金锭及其熔化成形方式ASTM B183－1979(1997) 电镀用低碳钢的制备ASTM B187－B187M－2003 铜汇流棒、条和型材ASTM B208－2004 砂型、永久型、离心型和连续铸造铸件用的铜基合金拉伸试验样件制备标准惯例ASTM B230－B230M－2004 电气用1350－H19型铝线ASTM B231－B231M－2004 同心绞捻铝1350导线ASTM B232－B232M－2001 涂覆钢芯加强的同心绞捻铝导线(ACSR)ASTM B233－2003 电气用1350铝拉制坯料ASTM B234－2004 冷凝器及热交换器用拉制铝和铝合金无缝管ASTM B240－2004 压模铸造用锌及锌铝合金锭ASTM B242－1999(2004)e1 电镀用高碳钢的制备ASTM B249M－2006 铜和铜合金棒材、型材及锻件ASTM B311－1993(2002)e1 孔隙度小于2%的粉末冶金材料密度的标准测试方法ASTM B328－2003 烧结金属结构零件和油浸轴承密度与互连多孔性的试验方法规范ASTM B368－1997(2003) 加速铜氧化的醋酸盐喷雾试验(cass试验)ASTM B36M－2006 黄铜板、薄板、带材及轧制棒材ASTM B380－1997 装饰性电镀层的腐蚀膏试验中文版ASTM B388－2000 恒温双金属薄板和带材ASTM B389－1981(2004) 恒温双金属螺旋形线圈的热偏转率的测试方法ASTM B407－2001 镍铁铬合金无缝管ASTM B423－2005 镍铁铬钼铜合金无缝管ASTM B425－1999 镍铁铬钼铜合金(UNS N08825和UNS N08221)杆材和棒材标准规范ASTM B435－2003统一编制牌号为NO6002、NO6230、N12160和R30556的板材和带材及牌号为N06002、N06230和R30556的带材ASTM B439－2000 铁基烧结轴承(油浸的)ASTM B446－2000 镍铬钼钶合金(UNS N06625)条和棒规范ASTM B446－2003 镍铬钼钶合金(UNS N06625)条和棒规范ASTM B456－1995 铜+镍+铬及镍+铬的电解沉积镀层标准规范ASTM B466 B466M－2003 无缝铜镍合金管ASTM B488－2001(2006) 工程用电解沉积镀金层ASTM B527－1993用塔普－帕克(Tap－Pak)容量计测定金属粉末及化合物粉末的塔普(Tap)密度的标准试验方法ASTM B557－2002a 锻造和铸造的铝及镁合金制品的抗拉试验的标准试验方法ASTM B580－2000 铝阳极氧化镀层ASTM B594－2006 航空用铝合金锻件超声波检测ASTM B604－1991(97) 塑料表面装饰用铜加镍铬镀层标准规范ASTM B619－2005 焊接的镍和镍钴合金管ASTM B626－2004 焊接的镍和镍钴合金管ASTM B633－1998 钢和铁电积沉淀镀锌的标准(中文)ASTM B66－2003 蒸汽机车易损零件用青铜铸件ASTM B670－2002 高温设备用沉淀淬火镍合金(UNS N07718) 厚板、薄板及带材的标准规范ASTM B680－1980(00) 用酸溶解法测定铝的阳极镀层封闭质量的试验方法ASTM B68－2002 光亮退火的无缝铜管ASTM B689－1997(2003) 电镀工程镀镍层ASTM B689－2003 电镀工程镀镍层ASTM B733－2004 化学镀镍ASTM B735－1995(2000) 用硝酸蒸汽测试金属基体上金涂层孔隙度的方法ASTM B748－1990(2006) 用扫描电子显微镜测量横截面测定金属涂层厚度的方法ASTM B824－2004 铜合金铸件ASTM B870－2002 铜－铍合金锻制和挤制合金C17500和C17510的标准规范ASTM B912－2000 用电抛光法测定不锈钢钝化的标准规范ASTM B912－2002 电解抛光ASTM B93－2006 砂型铸件、永久型模铸件和压模铸件用镁合金锭ASTM B94－2005 镁合金压铸件ASTM C 系列标准ASTM C1005－2000 水硬水泥物理试验中质量和体积测定用标准质量与称重器具的标准规范ASTM C1017&C1017M－1998 生产流动混凝土用的化学混合物的标准规范ASTM C1025－2000 石墨电极芯挠曲断裂模数的试验方法ASTM C1038－2004 存放在水中的水硬性水泥灰浆棒膨胀的标准试验方法ASTM C1039－2000 石墨电极的表观孔隙率、表观比重和松密度的试验方法ASTM C1043－2006 使用护热板装置中线电源加热器时稳态热传导特性测量用的加热板温度的测定ASTM C109&C109M－2002ASTM C110－2006 生石灰,熟石灰和石灰石的物理试验方法ASTM C1107－2002 干包装水硬水泥砂浆(非收缩的)标准规范ASTM C113－1993 耐火砖的二次加热变化的标准试验方法ASTM C1134－1990 部分浸入后刚性热绝缘材料水分保持标准试验方法ASTM C114－2004a 水硬水泥化学分析的标准试验方法ASTM C1166－2000 致密及多孔弹性体衬垫和附件火焰蔓延的试验方法ASTM C1179－2000 室外加工碳素材料及石墨材料氧化质量损失试验方法ASTM C1222－2006 实验室试验水硬水泥的评定ASTM C1276－1994 利用旋转米度计测量模制粉末熔点以上粘度的标准试验方法ASTM C1293－2006 用测定碱－硅石反应引起的混凝土长度变化对混凝土集料的标准试验方法ASTM C1305－2006 液体外加防水薄膜的裂缝挖补能力的标准测定方法ASTM C131－2006 用洛杉机磨耗试验机测定小规格粗集料的抗磨性与抗冲击性的试验方法ASTM C1329－2004 砂浆水泥的标准规范ASTM C1398－1998(04)用吉尔摩水泥稠度试验针实验室测定含喷浆混凝土添加剂的水硬水泥砂浆凝固时间的标准试验方法ASTM C1437－2001 水硬水泥灰浆流动性的标准试验方法ASTM C146－1994a(1999) 玻璃沙的化学分析试验方法ASTM C148－2000 玻璃容器偏振检验的试验方法ASTM C149－1986(2000) 玻璃容器热冲击的试验方法ASTM C158－2002 玻璃的挠曲试验方法(测定玻璃挠折模量)ASTM C1587－2006Standard PraASTM CtiASTM Ce for Preparation of Field Removed ManufaASTM Ctured Masonry Units and Masonry SpeASTM Cimens for ASTM Compressive Strength TestingASTM C169－1992(2000) 碱石灰玻璃及硅酸盐玻璃的化学分析试验方法ASTM C170－1990(R1999) 天然建筑石料抗压强度的试验方法ASTM C186(2000) 玻璃容器的内压的试验方法ASTM C－1997 用护热板法测定稳态热通量和传导性的标准试验方法ASTM C224－78(2004)e1 玻璃容器的取样方法ASTM C225－1985(1999) 玻璃容器耐化学腐蚀的试验方法ASTM C24－2001（2006）耐火和高矾土耐溶材料的溶锥当量测试法ASTM C242－2001 卫生陶瓷及其制品术语ASTM C25－2006 石灰石,生石灰和熟石灰的化学分析方法ASTM C270－2006 砌块用的灰浆ASTM C273－2000 夹层结构或夹层芯材的平直剪切性能的试验方法ASTM C305－2006 塑性稠度的水硬性水泥泥浆和灰浆机械搅拌ASTM C32－2004 污水管及检查井用砖(粘土或页岩)ASTM C329－1988(2006) 焙烧卫生陶瓷材料比重的试验方法ASTM C428－05(2006) 石棉水泥无压污水管ASTM C428－2005(2006) 石棉水泥无压污水管ASTM C473－2006 石膏板制品和石膏板条的物理测试标准试验方法ASTM C51－2006 与石灰及石灰石相关的(工业用)名词术语ASTM C518－2004用热流计法测定稳态热通量和热传递特性的试验方法ASTM C559－2000 用物理测量法测定碳加工品及石墨制品松密度的试验方法ASTM C560－1998 石墨的化学分析试验方法ASTM C561－2000 石墨样品中灰分的检测方法ASTM C562－2000 石墨样品中水分的检测方法ASTM C565－1998 碳和石墨机械加工材料抗拉检验的试验方法ASTM C595－2006 混合水硬性水泥ASTM C61（2006）基恩(Keene)石膏水泥ASTM C611－1998 在室温时,炭加工品及石墨制品的电阻率的试验方法ASTM C625－2000 石墨辐射结果的报告ASTM C651－2000 在室温下用四点负荷法，测定炭加工品及石墨制品的抗挠强度的试验方法ASTM C662－1998 不透水的石墨管和插片ASTM C67－2006 砖及结构粘土瓦的取样和试验的试验方法ASTM C695 －2000 碳和石墨和抗压强度的试验方法ASTM C70－2006 细集料表面湿度的测试方法ASTM C704－2001 室温下耐火材料耐腐蚀的试验方法ASTM C709－2003 炭和石墨加工术语ASTM C714－2000 用热脉冲法测定炭和石墨的热扩散系数的测试方法ASTM C747－1998 用音响共振法测定炭精和石墨的弹性模量与基本频率的试验方法ASTM C748－1998 细粒石墨材料的洛氏硬度的测试方法ASTM C749－2002 碳和石墨抗拉应力的试验方法ASTM C769－1998 为获得近似扬氏模量测量加工的炭精及石墨材料中音速的试验方法ASTM C773－1988(2006) 预制封缝带泛油或增塑剂泛出的试验方法ASTM C781－2002 高温气冷核反应堆用试验石墨及硼酸化石墨元部件的标准操作ASTM C783－2003 预制封缝带柔软度的测试方法ASTM C808－2000 炭加工的及石墨制承重材料和密封材料的磨擦及磨蚀结果的报告指南ASTM C816－1998 用燃烧碘量滴定法测定石墨中硫含量的试验方法ASTM C838－2001 加工炭精及石墨型材松密度的试验方法ASTM C880－2006 天然建筑石料弯曲强度的试验方法ASTM C886－1998 细粒炭精和石墨材料肖氏硬度的试验方法ASTM C90－2006a 承重混凝土空心砌块ASTM C94－2004 搅拌好的混凝土规范ASTM C94－2006 搅拌好的混凝土规范ASTM C989－2006 混凝土和灰浆用研磨成颗粒状的高炉碎渣的技术规范ASTM C990－2006 使用预制接缝密封胶粘结的混凝土管道、检查孔和预制箱型型件ASTM C99－1987(R2006) 规格石料断裂模数的试验方法ASTM D 系列标准ASTM D0091－2002润滑油的沉淀值试验方法ASTM D1002－2001 用拉力负载测定金属之间胶粘剂抗剪切强度特性的试验方法ASTM D1002－2005 用拉力负载测定金属之间胶粘剂抗剪切强度特性的试验方法ASTM D1003－1997 ;RASTM DEWMASTM DMTUKVEASTM D1003－2000 ;RASTM DEWMASTM DM－ASTM D1004－1994 ;RASTM DEWMASTM DQTOTRBASTM D1004－1994a R03 ;RASTM DEWMASTM DQTOTRBUJAZASTM D1004－1994a R03 ;RASTM DEWMASTM DQTUKVEASTM D1004－2003 ;RASTM DEWMASTM DQ－ASTM D1004－2003 塑料薄膜和薄板的抗撕裂强度的测试方法ASTM D1005－1995 用千分尺测量有机涂层干膜厚度的试验方法ASTM D1007－2000 仲丁醇ASTM D1007－2005 仲丁醇ASTM D1015－1999高纯烃凝固点测定试验方法ASTM D1015－2004 高纯度烃冻结点的测试方法ASTM D1016－1999 烃纯度试验方法ASTM D1016－2004 冻结点测定烃纯度的试验方法ASTM D1018－2000 石油馏分中氢含量的测试方法ASTM D1018－2000 石油馏分中氢试验方法ASTM D1018－2000(2005) 石油馏分中氢含量的测试方法ASTM D1025－2000 聚合级丁二烯中不挥发性残余物的试验方法ASTM D1025－2000 聚合级丁二烯中固定渣滓试验方法ASTM D1042－1993 ;RASTM DEWNASTM DITOTM－ASTM D1042－2001 ;RASTM DEWNASTM DI－ASTM D1042－2001 ;RASTM DEWNASTM DITMASTM DE－ASTM D1042－2001 ;RASTM DEWNASTM DITUKVEASTM D1043－1999 ;RASTM DEWNASTM DMTOTK－ASTM D1043－1999 ;RASTM DEWNASTM DMTUKVEASTM D1043－2002 ;RASTM DEWNASTM DM－ASTM D1044－1999 ;RASTM DEWNASTM DQ－ASTM D1044－2005 透明塑料表面耐磨蚀性的试验方法ASTM D1045－1995 ;RASTM DEWNASTM DUTOTU－ASTM D1045－1995 R01 ;RASTM DEWNASTM DU－ASTM D1052－1999 用罗斯挠曲装置测定橡胶切口扩展的试验方法ASTM D1053－1997 橡胶特性试验.挠性聚合物和涂覆制品的低温劲度测试方法ASTM D1054－1991 用回跳摆锤法测定橡胶弹性的试验方法ASTM D1055－1997 ;RASTM DEWNTU－ASTM D1056－1998 ;RASTM DEWNTYTUKVEASTM D1056－2000 ;RASTM DEWNTY－ASTM D1062－1996 金属间粘结力抗裂强度的标准试验方法ASTM D1066－2001 蒸汽的抽样方法ASTM D1067－2002 水的酸性和碱性的测试方法ASTM D1068－2003 水中铁的测定ASTM D1068－2003 水中铁的测试方法ASTM D1076－1997 橡胶.浓缩的、氨储存的、乳状的和离心处理的天然胶乳ASTM D1078－2003 挥发性有机液体馏程的测定方法ASTM D1078－2003 挥发性有机液体馏程的试验方法ASTM D1083－1991(98)集装箱、大型船运箱和板条箱的机械搬运的试验方法ASTM D1084－1997 胶粘剂粘度的测试方法ASTM D1091－2000 润滑油和添加剂中磷含量的测试方法ASTM D1091－2000 润滑油及添加剂中磷试验方法ASTM D1092－1999 润滑油可测量表观粘度试验方法ASTM D1092－1999 润滑脂表观粘度的试验方法ASTM D1093－1998 液态烃和它们的蒸馏残余物酸度的测试方法ASTM D1094－00 航空燃料水反应性的试验方法ASTM D1094－2000 航空燃料水反应性的试验方法ASTM D1094－2000 航空燃料易溶于水成分试验方法ASTM D1101－1997a 室外用层压结构木制品的胶合接头完整性的试验方法ASTM D1102－1984(2001)木材中灰分的测试方法ASTM D1125－1999 水的电导性和电阻率的测试方法ASTM D1125－1999 水中的电导和电导率测定法ASTM D1126－2002 水硬度的测试方法ASTM D1126－2002 水中的总硬度 (以 CaCO3计)ASTM D1129－2004 与水相关的术语ASTM D1133－2004 烃类溶剂的贝壳杉脂丁醇值的测试方法ASTM D1141－2003 海水代用品ASTM D1144－1999 胶粘剂粘结强度提高的测定方法ASTM D1146－2000 有效粘结层粘结点的试验方法ASTM D1148－1995 橡胶变质.受热及紫外线使浅颜色表面退色的试验方法ASTM D1149－1999 橡胶变质试验.在小室中橡胶表面臭氧龟裂ASTM D1149－99 橡胶变质试验.在小室中橡胶表面臭氧龟裂ASTM D1151－2000 潮气和温度对胶粘剂粘结能力影响的试验方法ASTM D1152－2001 甲醇(甲基醇)ASTM D1153－2001 甲基异丁基甲酮ASTM D1157－1991 轻烃中TBC测试试验方法ASTM D1157－2000 轻质烃总抑制剂含量(TBC)的测试方法ASTM D1159－2001 电化学滴定法测量石油馏分及商用脂族烯烃的溴值试验方法ASTM D1159－2001 电位滴定法测试石油馏出物和脂肪烃溴数ASTM D1160－2002a 减压蒸馏石油产品试验方法ASTM D1160－2003 石油产品减压蒸馏方法ASTM D116－1986(2006) 电气设备用上釉陶瓷材料的试验ASTM D1171－1999 橡胶变质试验.室外或小室内橡胶表面臭氧龟裂(三角形试样) ASTM D1179－2004 水中氟化物离子的测试方法ASTM D1183－1996 胶粘剂耐周期性实验室老化条件的标准试验方法ASTM D1184－1998 胶粘剂粘结的层压部件抗挠强度的试验方法ASTM D1186－2001 铁基非磁性涂层干膜厚度的无损测量方法ASTM D1192－1998 水和蒸汽的抽样设备标准指南ASTM D1193－1999 试剂水(联邦试验方法No.7916)ASTM D1200－1994(2005) 福特粘度杯测定粘度的试验方法ASTM D1201－1999 ;RASTM DEYMASTM DE－ASTM D1203－1994 R03 ;RASTM DEYMASTM DM－ASTM D1203－1994 R99 ;RASTM DEYMASTM DMTOTRSOTLFMQ－－ASTM D1204－1994 ;RASTM DEYMASTM DQTOTRFMQ－－ASTM D1204－1994 ;RASTM DEYMASTM DQTUKVEASTM D1204－2002 ;RASTM DEYMASTM DQ－ASTM D1209－2000 透明液体色度的试验方法(铂钴标度)ASTM D1209－2000 无色透明液体色度的测定方法(铂钴标度)ASTM D1210－1996 颜料载体体系分散细度的测试方法ASTM D121－2005 煤和焦炭术语ASTM D1217－1993 宾汗比重瓶测试液体密度试验方法ASTM D1217－1993 用宾汉比重法测定液体密度和相对密度(比重)的试验方法ASTM D1217－2003 用宾汉比重法测定液体密度和相对密度(比重)的试验方法ASTM D1218－2002 碳氢化合物折射率试验方法ASTM D1218－2002 液态烃的折光率和折光分散度的测试方法。
ASTMD79200塑料密度测试标准ASTMD792用浮力法测定塑料密度和
ASTM D792 00塑料密度测试标准ASTM D792用浮力法测定塑料密度和比重(相关密度)的标准试验方法本标准由方法D 792发布；紧接着名称后的数字表示最初版本的年份，或者是修改后的最后版本年份。
括号内的数字表示版本最后批准的年份。
上标有∈表示对最后一次修订本或批准的编辑修改。
本标准已经国防部代理处批准使用。
1、范围*1.1本测试方法描述了固体塑料的比重（相关密度）的密度的测定，如板材、杆轴、管束或塑料制品。
1.2测试方法有两种：1.2.1方法A：测试在水里的固体塑料1.2.2方法B：测试在除水以外的其他液体里的固体塑料注1：也可以选择方法D1505，此方法可用在上述材料以及胶面和板材。
1.3本标准以在SI单元表示的数据为标准数据。
1.4本标准无意体积所有的安全注意事项，如有，也仅是与其使用有关。
标准的使用者有责任使用本标准前指定合适的安全防范措施，并确定各项安全条令的适用性。
注2：本标准比不等同于ISO 1183中方法A。
2、参考标准2.1ASTM标准D618塑料和电绝缘材料实验的状态调节2D891液态工业化合物的比重,表观比重的标准试验方法3D1505用密度梯度法测试塑料密度的测试方法2D1622硬质泡沫塑料的表观密度的测试方法2D1898塑料制样操作4D4968塑料的试验方法和使用的年度复审标准指南2E1 ASTM温度计使用5E12 固体、液体及气体密度和比重的有关术语6E380 SI制国际体制的使用操作（现代化的十进制）7E691采用实验室间合作研究确定检测方法精密度73、术语3.1常规——本测试中使用的计量单位、标志的缩写都以E380为依据3.2名词解释：3.2.1比重（相关密度）——物质不能渗透的一部分的单位体积在23。
C的空气里和在相同温度下不含气体蒸馏水的同等体积的同等密度的比值。
公式表示为：sp gr23/23。
C注3：此精确度与术语E12里表观比重和表观密度的精确度本质上相等，因为由不准确的空气浮力得来的细微的百分比差异不影响整体效果。
宝钢锌铁合金规格一览表
品名规格材质材质说明产地热镀锌锌铁合金0.42*940*0 Grade 550 —ASTM A792 Grade 550-N-AZ150-UF 宝钢股份热镀锌锌铁合金0.47*940*0 Grade 550 —ASTM A792 Grade 550-N-AZ150-UF 宝钢股份热镀锌锌铁合金0.48*1000*0 宝钢股份热镀锌锌铁合金0.48*970*0 Grade 550 —ASTM A792 Grade 550-N-AZ150-UF 宝钢股份热镀锌锌铁合金0.48*1130*0 Grade 550 —ASTM A792 Grade 550-N-AZ150-UF 宝钢股份热镀锌锌铁合金0.5*1017*0 宝钢股份热镀锌锌铁合金0.5*1000*0 宝钢股份热镀锌锌铁合金0.6*1250*0 H260YD+ZF —Q/BQB 420 H260YD+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金0.6*1680*0 SP783BJQ —NES M2027 SP783BJQ 宝钢股份热镀锌锌铁合金0.6*840*0 SP783BQ —M2027 SP783BQ 宝钢股份热镀锌锌铁合金0.6*840*0 SP783BQ —M2027 SP783BQ 宝钢股份热镀锌锌铁合金0.6*1680*0 DC54D+ZF —GT1802 DC54D+ZF 45/45-R-L Y 宝钢股份热镀锌锌铁合金0.6*1200*0 JAC590Y —HES C071 JAC590Y C N-1201-O SD-45/45 宝钢股份热镀锌锌铁合金0.6*1200*0 JAC590R #NAME? 宝钢股份热镀锌锌铁合金0.6*900*0 JAC270C —HES C071 JAC270C U N-1201-O SD-45/45 宝钢股份热镀锌锌铁合金0.6*1583*0 DC51D+ZF —Q/BQB 420 DC51D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金0.6*1200*0 JAC270E —HES C071 JAC270E U N-1211-L SD-45/45 宝钢股份热镀锌锌铁合金0.6*1380*0 SCGA270D —TSG3109G SCGA270D 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金0.6*900*0 DC52D+ZF —BQXH2005-100 DC52D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金0.6*1200*0 JAC270F —HES C071 JAC270F U N-1211-L SD-45/45 宝钢股份热镀锌锌铁合金0.6*1400*0 St05ZF —BQXH2005-016 St05ZF140RB-O 宝钢股份热镀锌锌铁合金0.65*1670*0 SP783BQ —NES M2027 SP783BQ热镀锌锌铁合金0.75*1630*1770 DC51D+ZF热镀锌锌铁合金1.2*1644*0 H220YD+ZF —Q/BQB 420 H220YD+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.2*1000*0 B450LAD+ZF —BKJ04-901 B450LAD+ZF-45/45-R-FB-Y 宝钢股份热镀锌锌铁合金1.2*1048*0 JAC270C —宝钢股份热镀锌锌铁合金1.2*980*0 DC52D+ZF —Q/BQB 420 DC52D+ZF 45/45-R-FB-Y 宝钢股份热镀锌锌铁合金1.2*1060*0 DC52D+ZF —BQXH2005-100 DC52D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.2*1368*0 DC52D+ZF —BQXM2005-079 DC52D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.2*1045*0 SCGA270D —TSG3109G SCGA270D 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.2*1560*0 SCGA270D —TSG3109G SCGA270D 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.2*1560*0 SCGA270D —TSG3109G SCGA270D 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.2*916*0 DC54D+ZF —Q/BQB 420 DC54D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.2*1175*0 DC54D+ZF —Q/BQB 420 DC54D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.5*1360*0 DC53D+ZF —Q/BQB 420 DC53D+ZF 40/40-R-FC-Y 宝钢股份热镀锌锌铁合金1.5*1170*0 DC54D+ZF —GT1802 DC54D+ZF 45/45-R-Y 宝钢股份热镀锌锌铁合金0.9*935*C SCGA270D+ZF —TSG3109G SCGA270D 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*880*C SP782-440BQ+ZF —NES M2027 SP782-440BQ 宝钢股份热镀锌锌铁合金1.4*1020*C DC51D+ZF —BQXM2006-042 DC51D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金0.9*1005*C CR280+ZF —BQXH2005-151 CR280 HD45A45AU 宝钢股份热镀锌锌铁合金0.9*1005*C CR280+ZF —BQXH2005-151 CR280 HD45A45AU 宝钢股份热镀锌锌铁合金0.9*1200*C SCGA270D+ZF —TSG3109G SCGA270D 45/45-R-FC-SL 宝钢股份热镀锌锌铁合金0.9*1005*C SP783BQ+ZF —NES M2027 SP783BQ 宝钢股份热镀锌锌铁合金0.9*1565*C DC54D+ZF —BQXH2005-100 DC54D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*880*C SP782-440BQ+ZF —NES M2027 SP782-440BQ 宝钢股份热镀锌锌铁合金1.4*1020*0 DC54D+ZF —Q/BQB 420 DC54D+ZF 40/40-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*1140*0 DC56D+ZF —Q/BQB 420 DC56D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*1362*0 DC54D+ZF —BQXM2005-080 DC54D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.41*1050*0 SCGA270D —TSG3109G SCGA270D 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.5*1300*0 H260PD+ZF —Q/BQB 420 H260PD+ZF 40/40-R-FC-Y 宝钢股份热镀锌锌铁合金1.5*1180*0 H260PD+ZF —Q/BQB 420 H260PD+ZF 40/40-R-FC-Y 宝钢股份热镀锌锌铁合金1.5*1250*0 DX51D+ZF —EN 10142 DX51D+ZF 99-R-B-O 宝钢股份热镀锌锌铁合金1.5*1250*0 DC51D+ZF —Q/BQB 420 DC51D+ZF-40/40-R-FC-L 宝钢股份热镀锌锌铁合金1.5*1250*0 DC51D+ZF —Q/BQB 420 DC51D+ZF-40/40-R-FC-L 宝钢股份热镀锌锌铁合金1.5*1360*0 DC53D+ZF —Q/BQB 420 DC53D+ZF 40/40-R-FC-Y 宝钢股份热镀锌锌铁合金1.5*1170*0 DC54D+ZF —GT1802 DC54D+ZF 45/45-R-Y 宝钢股份热镀锌锌铁合金1.4*1650*0 DC54D+ZF —Q/BQB 420 DC54D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*953*0 SCGA440 —TSG3109G SCGA440-45 宝钢股份热镀锌锌铁合金1.4*1200*0 JAC590R —HES C071 JAC590R C N-1201-O SD-45/45 宝钢股份热镀锌锌铁合金1.4*1120*0 SCGA440 —TSG3109G SCGA440-45 宝钢股份热镀锌锌铁合金1.4*1125*0 APFC340 —BQXH2005-063 EDS-M-1201热镀锌锌铁合金1.4*1110*0 B450LAD+ZF —BQXM2006-056 B450LAD+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*1260*0 B450LAD+ZF —BKJ04-901 B450LAD+ZF-45/45-R-FB-Y 宝钢股份热镀锌锌铁合金1.4*1260*0 B450LAD+ZF —BQXM2006-056 B450LAD+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*1260*0 B450LAD+ZF —BQXM2006-056 B450LAD+ZF 45/45-R-FC-Y宝钢股份热镀锌锌铁合金1.4*1420*0 B450LAD+ZF —BKJ04-901 B450LAD+ZF-45/45-R-FB-Y 宝钢股份热镀锌锌铁合金1.4*1200*0 H260P1D+ZF —GT1802 H260P1D+ZF 45/45-R-Y 宝钢股份热镀锌锌铁合金 1.4*1050*0 B260L YD+ZF —BQXH2005-025 B260L YD+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*1230*0 B260L YD+ZF —BQXM2005-107 B260L YD+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金 1.4*1230*0 B240P1D+ZF —BQXM2005-107 B240P1D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*875*0 SCGA270D —TSG3109G SCGA270D 45 宝钢股份热镀锌锌铁合金1.4*875*0 SCGA270D —TSG3109G SCGA270D 45 宝钢股份热镀锌锌铁合金1.41*1050*0 SCGA270D —TSG3109G SCGA270D 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.5*1300*0 H260PD+ZF —Q/BQB 420 H260PD+ZF 40/40-R-FC-Y 宝钢股份热镀锌锌铁合金1.5*1180*0 H260PD+ZF —Q/BQB 420 H260PD+ZF 40/40-R-FC-Y 宝钢股份热镀锌锌铁合金1.5*1250*0 DX51D+ZF —EN 10142 DX51D+ZF 99-R-B-O 宝钢股份热镀锌锌铁合金1.5*1250*0 DC51D+ZF —Q/BQB 420 DC51D+ZF-40/40-R-FC-L 宝钢股份热镀锌锌铁合金1.4*1020*C DC51D+ZF —BQXM2006-042 DC51D+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*880*C SP782-440BQ+ZF —NES M2027 SP782-440BQ 宝钢股份热镀锌锌铁合金1.4*1660*900 H220YD+ZF —Q/BQB 420 H220YD+ZF 45/45-R-FC-Y 宝钢股份热镀锌锌铁合金1.4*1060*1585 DC54D+ZF —Q/BQB 420 DC54D+ZF 45/45-锌－铁合金镀技术简介。
ASTM A792M-2006
1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.
4. Classification
4.1 The material is available in several designations, as follows:
4.1.1 Commercial Steel—CS Types A, B, and C, 4.1.2 Forming Steel—FS, 4.1.3 Drawing Steel—DS, 4.1.4 High Temperature Steel—HTS, and 4.1.5 Structural Steel—SS. 4.2 Structural steel is available in several grades based on mechanical properties. Structural Steel Grade 50 [340] is available in three classes based on tensile strength. Structural Steel Grade 80 [550] is available in two classes, based on chemistry.
ASTM A90-2009 中文版：在铁和钢件上决定锌或锌合金重量的标准测试方法
ASTM A90－2009：在鐵和鋼件上決定鋅或鋅合金重量的標準測試方法1. 範圍1.1 本測試方法包括在鐵或鋼板、線、和其它物品上來決定其鋅或鋅合金例如5%-鋅鋁合金(包括5%-鋅鋁合金和5%-鋅0.1%-鋁鎂合金)或55% 鋁-鋅合金之塗層重量的程序。
除非有特別指定否則在本測試方法裡所提到的鍍鋅應被解釋為也包含鋅合金塗層在內。
1.2 由本測試方法所決定的最後結果應以英寸-磅單位或SI單位來表示，取決於在其材料規定的單位使用何種結果來作比較。
與樣品重量的測定有關的程序的某些部分已經習慣以SI 單位來實施，且不包含相對應英寸-磅單位。
1.3 對於板狀產品，其塗層的最後結果可以用雙邊的全部重量或是用每一單邊的重量來表示，是取決於其規範要求。
1.4 本標準並未指明試驗方法上所產生之任何安全問題，該安全問題是引用本標準之使用者的責任。
使用者應自行建立適當之安全衛生操作方法，並且在使用前決定應有的使用限制規定。
對特定的危險敘述請參閱 5.1。
2. 參考文件2.1 ASTM 標準A 653/A 653M 鍍鋅(熱浸)或以熱浸處理的鋅鐵合金塗層鋼板的規定A 792/A 792M 以熱浸處理的55%鋁鋅合金塗層的鋼板的規定A 875/A 875M 以熱浸處理的5%-鋅鋁合金塗層的鋼板的規定D 1193 試藥水的規定E 29 在測試資料上使用有效數字用以確定符合的練習3. 重要性和使用3.1 本測試方法對於比較與規範要求上之塗層重量的決定提供一種標準方法。
在鐵或鋼物品上的鋅塗層用來提供保護以防止腐蝕。
由於保護是藉由鋅的犧牲性損失所提供，因此保護的程度與鍍鋅的重量成正比。
鋅塗層物品的規範上經常提供各種各樣的塗層等級，以便採購者能選擇最適合他所需要的塗層重量。
4. 試藥4.1 純的試藥：於所有的測試上應使用試藥等級的化學品。
除非另有規定，期望所有的試藥都能符合美國化學協會的分析試藥委員會的規範，在這樣的規格是有效的。
镀锌钢卷标准
1240～1260 0.60～1.60A653M SS Gr ade340 A653 SS Grade50900～920920～12301230～12500.28～1.600.35～1.600.40～1.60900～920920～12301230～12500.28～1.600.35～1.600.40～1.60A653M SS Gr ade550 A653 SS Grade80900～920920～940940～12301230～12500.21～1.600.25～1.600.28～1.600.47～1.40900～920920～940940～12301230～12500.21～1.200.25～1.600.28～1.600.47～1.40A653M DDS A653 DDS 900～1250 0.30～1.60 900～1250 0.30～1.60镀层量及可适用之冷轧厚度范围公制：Z080：0.30 ～1.60 mmZ120 , Z180 , Z275：0.20 ～1.60 mm Z350：0.40 ～1.60 mm英制：G40 , G60 , G90：0.20 ～ 1.60 mmG115：0.40 ～1.60 mmB.镀铝锌重量范围: 40g/m2 ~ 200g/m2 (两面总合)C.表面精整: 一般花纹、超平滑D.可供应钢卷等级: 一般级、扣锁成型级、冲压级、结构级热浸镀55%铝锌钢卷种类符号冷轧底板最小降伏点N/mm2最小抗拉强度N/mm2最小伸长率% 用途公称厚度mm (t)JIS G3321-1 998 盛余规格0.25≤t<0.40.4≤t<0.60.6≤t<1.01.0≤t<1.61.6≤t<2.3SGLCC SGLC (205) (270) (20) (21) (24) (24) (25) 一般用SGLCD SGLD1 --- 270 --- 27 31 32 33 冲压用--- SGL340 245 340 20 20 20 20 20 结构用SGLC400 SGL400 295 400 16 17 18 18 18 结构用SGLC440 SGL440 335 440 14 15 16 18 18 结构用SGLC490 SGL490 365 490 12 13 14 16 16 结构用SGLC570 SGL570 560 570 --- --- --- --- --- 结构用ASTM 代号1999版最小降伏点最小抗拉强度最小伸长率% 用途ksi(MPa) ksi(MPa)A792(M)-99 CS TYPEA,B,C--- --- --- 一般用A792(M)-99 FS --- --- --- 扣锁成型用A792(M)-99 DS --- --- --- 冲压用A792(M)-99 SS Grade33(230)33(230) 45(310) 20 结构用A792(M)-99 SS Grade37(255)37(255) 52(360) 18 结构用A792(M)-99 SS Grade440(275) 55(380) 16 结构用A792(M)-99 SS Grade50(345)50(345) 65(450) 12 结构用 A792(M)-99 SS Grade80(550)80(550) 82(570)---结构用备注: J IS/SYSCO: JIS/SYSCO: ( )内的数值仅供参考ASTM:A792(M) 表公制, 以 ( ) 数字表示. 镀锌钢卷A.表面精整: 一般花纹, 微细花纹, 超平滑 1.一般花纹: 镀锌后之钢板无任何处理而自然成形之花纹,又称正常花纹.2.微细花纹:在锌液中降低铅之成份或另于锌槽上方加装喷锌粉之设备, 以抑制锌花成长.3.超平滑: 在微小花纹再经调质机调质, 使其在表面可得到均匀平滑之表面.B.可供应钢卷等级: 一般级, 扣锁成型级, 结构级, 冲压级JIS G3302-1998 / SYSC O热浸镀锌钢卷种类符号 最小降伏点 N/mm 2最小抗拉强度 N/mm 2最小伸长率 % 用途公称厚度 mm (t)冷軋底板熱軋底板0.25≤t<0.40.4≤ t<0.6 0.6≤ t<1.0 1.0≤ t<1.6 1.6≤ t<2.5 t≥2.5 SGCC SGHC --- --- --- --- --- --- --- --- 一般用 SGCH --- --- --- --- --- --- --- --- --- 全硬直一般用 SGCD1 --- --- 270 --- 34 36 37 38 --- 冲压用 SGC340 SGH340 245 340 20 20 20 20 20 20 结构用 SGC400 SGH400 295 400 18 18 18 18 18 18 结构用 SGC440 SGH440 335 440 18 18 18 18 18 18 结构用 SGC490 SGH490 365 490 16 16 16 16 16 16 结构用 --- SGH540 400 540 16 16 16 结构用 SGC570560570------------------结构用 ASTM 代号 1999版最小降伏点 最小抗拉强度 最小伸长率 % 用途ksi(MPa)ksi(MPa) A653(M)-99 CS TYPE A,B,C--- --- --- 一般用 A653(M)-99 FS TYPE A,B--- --- --- 扣锁成型用 A653(M)-99 DDS------ --- 冲压用 A653(M)-99 SS Grade3333(230)45(310)20结构用A653(M)-99 SS Grade3737(255) 52(360) 18 结构用(255)40(275) 55(380) 16 结构用A653(M)-99 SS Grade40(275)50(340) 65(450) 12 结构用A653(M)-99 SS Grade50(340)80(550) 82(570) --- 结构用A653(M)-99 SS Grade80(550)备注:ASTM:A653(M) 表公制, 以数字表示( ).补充：“镀55%铝锌钢卷”之铝锌合金结构是由55%铝、43.4%锌与1.6%矽在600ºC高温下固化而组成，其整个结构由铝－铁－矽－锌，形成致密的四元结晶体，此结晶体在钢板上形成一层屏障，因而有效的防止腐蚀因子穿透。
BASF-A蜡
德国巴斯夫Luwax A乙烯均聚蜡性能性能测试方法测试方法乙烯均聚蜡乙烯均聚蜡DGF DGFDIN DINASTM ASTMLuwax A Luwax A物理形态物理形态 - - - 粉状 特点特点 - - - - 颜色颜色 - - - 白色 熔点熔点(℃)DSC (℃)DSC (℃)DSC- 51007 D-3418 101-109 熔点熔点(℃) (℃) (℃) 有加热台的显微镜测有加热台的显微镜测有加热台的显微镜测 - 53736 D-2117 98-108 凝结点凝结点(℃) (℃) (℃) 旋转温度计测旋转温度计测旋转温度计测 M-1114a51556/ISO 2207D-938 92-100 凝结点凝结点(℃) (℃) (℃) - 51007 - 94-100 滴点滴点(℃) (℃) (℃) M-1113 51801 D-566 103-110 针入值针入值(dmm)23℃(dmm)23℃(dmm)23℃ M-1119b 51579 D-1321 1-2 球氏硬度球氏硬度(bar)23℃(bar)23℃(bar)23℃ M-1119a - - 150-300酸值酸值(mg KOH/g)(mg KOH/g)(mg KOH/g) M-IV 2 53402 D-1386 0 皂化值皂化值(mg KOH/g)(mg KOH/g)(mg KOH/g) M-IV 2 53401 D-1387 0 熔融黏度熔融黏度(mm2/s)120℃(mm2/s)120℃(mm2/s)120℃ M-1118 51562 D-2162 950-1550 分子量分子量(g/mol)(g/mol)(g/mol) - - - ～7000 密度密度(g/(g/(g/cm3)23℃cm3)23℃M-1112a53479D-7920.91-0.93Luwax 蜡粉特点:高压无催化聚合过程 黏度低，加工性好 分子量分布窄，耐热性优良可用于生产食品包装只有色母粒的黏度在加工温度下低于欲着色的塑料，才有足够的剪切力来分散颜料。
钢材大全ASTM-A钢材标准(5)(A792-A921)
Standard Specification for Cold-Worked 冷加工焊接奥氏体不锈钢管
Welded Austenitic Stainless Steel Pipe
Standard Specification for Wrought 锻制铁素体、铁素体/奥氏体和
Ferritic,Ferritic/Austenitic, and 马氏体不锈钢管配件
A805-93(2002)
冷轧碳素钢扁平线
Standard Specification for Steel, Flat Wire, Carbon,Cold-Rolled
A807/A807M-02e1
Standard Practice for Installing Corrugated 下水道及其它类似用途用波纹
冷拉钢丝
Drawn for Prestressing Concrete Tanks
Standard Specification for Seamless 液压系统设备用冷拉碳素无缝
Cold-Drawn Carbon Steel Tubing for Hydraulic 钢管
System Service
防火用黑色及热浸镀锌的焊接 Hot-Dipped Zinc-Coated (Galvanized) Welded
和无缝钢管
and Seamless Steel Pipe for Fire Protection
Use
Standard Practice for Structural Design of 雨水管和卫生污水管及其它地
商品级冷轧碳素钢薄板(最高 含碳量为 0.16%-0.25%)
Standard Specification for Commercial Steel (CS), Sheet,Carbon (0.16% Maximum to 0.25% Maximum), Cold-Rolled
钢板材质牌号对照
钢板材质牌号对照Document serial number【UU89WT-UU98YT-UU8CB-UUUT-UUT108】、国内所有钢板材质牌号；如有不懂的可以咨询张先生主要销售以下钢板◆汽车钢热轧和酸洗可供牌号： 410XLF、050XLF、060XLF、070XLF、080XLF、SAPH310、SAPH370、SAPH400、SAPH440、SPFH540、SPFH590、QSTE340TM、QSTE380TM、QSTE420TM、QSTE460TM、QSTE500TM、QSTE550TM、QSTE600TM、QSTE700TM、S315MC、S355MC、S420MC、S460MC、S500MC、S550MC、S600MC、S700MC、B380CL、B420CL、B500CL、B550CL、B440QK、B320L、B510L、B550L、B590L、B520JJ、B750GJ、BR1200HS、BR1500HS、CP800、CP900、DP600、DP780、HR340、H420B、JSH440W、RP221P、RP252-540FPQ、SP231-440PQ、SP252-540FPQ、TL1406、ZQS500L等。
◆高强度热轧和高碳钢热轧可供牌号： A572GR55、A572GR65、BSM590、BS600MC、BS700MC、BS700MCK2、Q345C、Q345D、Q460C、Q460D、Q500D、Q550D、Welten590RE、S20C、S35C、S45C、S50C等。
◆耐候钢、焊瓶钢和管线钢可供牌号：05CuPCrNi、 09CuPCrNi-A、B450NQ、B460NQ、B500NQ、B480GNQR、Q355GNH、Q400NQR1、Q450NQR1、Q500NQR1、Q550NQR1、Q700NQR1、B440HP、B490HP、HP295、HP345、L450MB等。
ASTM D792_2000
ASTM-D792ADOPTION NOTICEASTM-D792, "DENSITY AND SPECIFIC GRAVITY (RELATIVE DENSITY) OFPLASTICS BY DISPLACEMENT", was adopted on 15-JUL-91 for use bythe Department of Defense (DoD). Proposed changes by DoDactivities must be submitted to the DoD Adopting Activity:Commander, Defense Supply Center Philadelphia, ATTN: DSCP-ILEA,700 Robbins Avenue, Philadelphia, PA 19111-5096. Copies of thisdocument may be purchased from the American Society for Testingand Materials 100 Barr Harbor Drive West Conshohocken,____________________ Pennsylvania, United States, 19428-2959. /--`-`-`,,`,,`,`,,`---Custodians:Adopting Activity:DLA - ISArmy - MRNavy - SHAir Force - 11DLA - GSReviewer Activities:Navy - YDFSC 9330DISTRIBUTION STATEMENT A:Approved for public release; distributionis unlimited.Copyright ASTM InternationalProvided by IHS under license with ASTMNot for ResaleNo reproduction or networking permitted without license from IHSimmersion is determined,and its specific gravity(relative density)calculated.5.Significance and Use5.1The specific gravity or density of a solid is a property that can be measured conveniently to identify a material,to follow physical changes in a sample,to indicate degree of uniformity among different sampling units or specimens,or to indicate the average density of a large item.5.2Changes in density of a single specimen may be due to changes in crystallinity,loss of plasticizer,absorption of solvent,or to other causes.Portions of a sample may differ in density because of difference in crystallinity,thermal history, porosity,and composition(types or proportions of resin, plasticizer,pigment,orfiller).N OTE6—Reference is made to Test Method D1622.5.3Density is useful for calculating strength-weight and cost-weight ratios.6.Sampling6.1The sampling units used for the determination of spe-cific gravity(relative density)shall be representative of the quantity of product for which the data are required,in accordance with Practice D1898.6.1.1If it is known or suspected that the sample consists of two or more layers or sections having different specific gravities,either completefinished parts or complete cross sections of the parts or shapes shall be used as the specimens, or separate specimens shall be taken and tested from each layer.The specific gravity(relative density)of the total part cannot be obtained by adding the specific gravity of the layers, unless relative percentages of the layers are taken into account.7.Conditioning7.1Conditioning—Condition the test specimens at 2362°C and5065%relative humidity for not less than40 h prior to test in accordance with Procedure A of Practice D618,unless otherwise specified by the contract or relevant material specifications.In cases of disagreement,the tolerances shall be61°C and62%relative humidity.7.2Test Conditions—Conduct tests in the standard labora-tory atmosphere of2362°C and5065%relative humidity, unless otherwise specified in this specification or by the contract or relevant material specification.In cases of disagree-ment,the tolerances shall be61°C and62%relative humid-ity.TEST METHOD A FOR TESTING SOLID PLASTICS IN WATER(SPECIMENS1TO50g)8.Scope8.1This test method involves weighing a one-piece speci-men of1to50g in water,using a sinker with plastics that are lighter than water.This test method is suitable for plastics that are wet by,but otherwise not affected by water.9.Apparatus9.1Analytical Balance—A balance with a precision within 0.1mg,accuracy within0.05%relative(that is,0.05%of the mass of the specimen in air),and equipped with a stationary support for the immersion vessel above the balance pan(“pan straddle”).N OTE7—Assurance that the balance meets the performance require-ments should be provided by frequent checks on adjustments of zero point and sensitivity and by periodic calibration for absolute accuracy,using standard masses.9.2Sample Holder,corrosion-resistant(for example,wire, gemholder,etc.).9.3Sinker—A sinker for use with specimens of plastics that have specific gravities less than1.000.The sinker shall:(1)be corrosion-resistant;(2)have a specific gravity of not less than 7.0;(3)have smooth surfaces and a regular shape;and(4)be slightly heavier than necessary to sink the specimen.The sinker should have an opening to facilitate attachment to the specimen and sample holder.9.4Immersion Vessel—A beaker or other wide-mouthed vessel for holding the water and immersed specimen.9.5Thermometer—A thermometer with an accuracy of 60.1°C is required.10.Materials10.1Water—The water shall be substantially air-free and distilled or demineralized water.N OTE8—Water may be rendered substantially air-free by boiling and cooling or by shaking under vacuum in a heavy-walled vacuumflask. (Precaution:Use gloves and shielding.)If the water does not wet the specimen,a few drops of a wettingagent shall be added.If this solution does not wet the specimen,Method B shall be used.11.Test Specimen11.1The test specimen shall be a single piece of the material under test of any size and shape that can conveniently be prepared and tested,provided that its volume shall be not less than1cm3and its surface and edges shall be made smooth.The thickness of the specimen should be at least1mm for each1 g of weight.A specimen weighing1to5g usually will be found convenient,but specimens up to approximately50g may be used(Note9).Care should be taken in cutting specimens to avoid changes in density resulting from compressive stresses or frictional heating.N OTE9—Specifications for certain plastics require a particular method of specimen preparation and should be consulted if applicable.11.2The specimen shall be free from oil,grease,and other foreign matter.12.Procedure12.1Measure and record the water temperature.12.2Weigh the specimen in air to the nearest0.1mg for specimens of mass1to10g or to the nearest mg for specimens of mass more than10to50g.12.3If necessary,attach to the balance a piece offine wire sufficiently long to reach from the hook above the pan to the support for the immersion vessel.In this case attach the specimen to the wire such that it is suspended about25mm above the vessel support.N OTE10—If a wire is used the specimen may be weighed in air after hanging from the wire.In this case,record the mass of the specimen,a =(mass of specimen +wire,in air)−(mass of wire in air).12.4Mount the immersion vessel on the support,andcompletely immerse the suspended specimen (and sinkers,ifused)in water (10.1)at a temperature of 2362°C.The vesselmust not touch sample holder or specimen.Remove anybubbles adhering to the specimen,sample holder,or sinker,paying particular attention to holes in the specimen and sinker.Usually these bubbles can be removed by rubbing them with awire.If the bubbles cannot be removed by this method or ifbubbles are continuously formed (as from dissolved gases),theuse of vacuum is recommended (Note 12).Determine the massof the suspended specimen to the required precision (12.2)(Note 11).Record this apparent mass as b (the mass of thespecimen,sinker,if used,and the partially immersed wire inliquid).Unless otherwise specified,weigh rapidly in order tominimize absorption of water by the specimen.N OTE 11—It may be necessary to change the sensitivity adjustment ofthe balance to overcome the damping effect of the immersed specimen.N OTE 12—Some specimens may contain absorbed or dissolved gases,or irregularities which tend to trap air bubbles;any of these may affect thedensity values obtained.In such cases,the immersed specimen may besubjected to vacuum in a separate vessel until evolution of bubbles hassubstantially ceased before weighing (see Test Method B).It must also bedemonstrated that the use of this technique leads to results of the requireddegree of precision.12.5Weigh the sample holder (and sinker,if used)in waterwith immersion to the same depth as used in the previous step13.Calculation 13.1Calculate the specific gravity of the plastic as follows:sp gr 23/23°C 5a /~a 1w 2b !where:a =apparent mass of specimen,without wire or sinker,in air,b =apparent mass of specimen (and of sinker,if used)completely immersed and of the wire partially im-mersed in liquid,and w =apparent mass of totally immersed sinker (if used)and of partially immersed wire.13.2Calculate the density of the plastic as follows:D 23C ,kg/m 35sp gr 23/23°C 3997.513.3If the temperature of the water is different than 23°C,the following equations will be used:M 5D D /D t (1)D –~conversion to 23°C !,kg/m 35sp gr t a /t w 3@997.51~t w –23!3M #(2)sp gr 23/235D ~conversion to 23°C !/997.5(3)where:M =slope,D D =difference between the lowest and highest tempera-ture tolerance for the standard density of water (D @A S r =within laboratory standard deviation for the individual material.It is obtained by pooling the within-laboratory standard deviations of the test results from all of the participating laboratories:S r =[[(s 1)2+(s 2)2...+(s n )2]/n]1/2B S R =between-laboratories reproducibility,expressed as standard deviation:S R =[S r 2+S L 2]1/2where S L is the standard deviation of laboratory means.C r =within-laboratory critical interval between two test results =2.83S r .D R =between-laboratories critical interval between two test results =2.83S R .different layers or areas of a nonhomogeneous product,14.1.4Report the temperature of the water.14.1.5Report the density and specific gravity with foursignificant figures.14.1.6Any evidence of porosity of the material or speci-men,14.1.7The method of test (Method A of Methods D 792),and14.1.8Date of test.15.Precision and Bias15.1See Section 23.TEST METHOD B FOR TESTING SOLID PLASTICSIN LIQUIDS OTHER THAN WATER (SPECIMENS 1TO 50g)16.Scope16.1Test Method B uses a liquid other than water for testingone-piece specimens,1to 50g,of plastics that are affected bywater or which are lighter than water.17.Apparatus17.1The apparatus shall include the balance,wire,andimmersion vessel of Section 8,and,optionally,the following:17.2Pycnometer with Thermometer —A 25-mL specificgravity bottle with thermometer,or17.3Pycnometer —A pycnometer of the Weld type,prefer-ably with a capacity of about 25mL and an external cap overthe stopper.17.4Thermometer —A thermometer having ten divisionsper degree Celsius over a temperature range of not less than5°C or 10°F above and below the standard temperature,andhaving an ice point for calibration.A thermometer shortenough to be handled inside the balance case will be foundconvenient.ASTM Thermometer 23C (see Specification E 1)and Anschütz-type thermometers have been found satisfactoryfor this purpose.17.5Constant-Temperature Bath —An appropriate constant-temperature bath adjusted to maintain a temperature of 2360.1°C.18.Materials 18.1Immersion Liquid—The liquid used shall not dissolve,swell,or otherwise affect the specimen,but should wet it and should have a specific gravity less than that of the specimen.In addition,the immersion liquid should be nonhygroscopic,have a low vapor pressure,a low viscosity,and a high flash point,and should leave little or no waxy or tarry residue on evaporation.A narrow cut distilled from kerosine meets these requirements for many plastics.The specific gravity 23/23°C of the immersion liquid shall be determined shortly before and after each use in this method to a precision of at least 0.1%relative,unless it has been established experimentally in the particular application that a lesser frequency of determination can be used to assure the desired precision.N OTE 15—For the determination of the specific gravity of the liquid,the use of a standard plummet of known volume (Note 15)or of Method A,C,or D of Test Methods D 891,using the modifications required to give specific gravity 23/23°C instead of specific gravity 60/60°F,is recom-mended.One suggested procedure is the following:If a constant-temperature water bath is not available,deter-mine the mass of the clean,dry pycnometer with thermometer to the nearest 0.1mg on an analytical balance.Fill the pycnometer with water (10.1)cooler than 23°C.Insert the thermometer-stopper,causing excess water to be expelled through the side arm.Permit the filled bottle to warm in air until the thermometer reads 23.0°C.Remove the drop of water at the tip of the side arm with a bit of filter paper,taking care not to draw any liquid from within the capillary,place the cap over the side arm,wipe the outside carefully,and determine the mass of the filled bottle again to the nearest 0.2mg.Empty the pycnometer,dry,and fill and determine the mass with the other liquid in the same manner as was done with the water.TABLE 2Test Method BSpecific Gravity Tested in Liquids Other Than Water MaterialMean S r A S R B r C R D Polypropylene0.90230.001390.002390.003930.00676LDPE0.92150.001090.001950.003080.00552HDPE0.96780.001260.001890.003560.01007Thermoset1.31300.001600.002170.004530.01282A S r =within laboratory standard deviation for the individual material.It is obtained by pooling the within-laboratory standard deviations of the test results from all of the participating laboratories:S r =[[(s 1)2+(s 2)2...+(s n )2]/n]1/2B S R =between-laboratories reproducibility,expressed as standard deviation:S R =[S r 2+S L 2]1/2where S L is the standard deviation of laboratory means.C r =within-laboratory critical interval between two test results =2.83S r .D R =between-laboratories critical interval between two test results =2.83S R .TABLE 3Standard Density of Water A°Cr /kg m –30.00.10.20.30.40.50.60.70.80.921997.994897319513929490738852863084068182795722997.773075037275704568156584635161185883564823997.541251744936469744564215397337303485324024997.299427472499225020001749149712440990073525997.048002239965B 9707B 9447B 9186B 8925B 8663B 8399B 8135B AObtained from CRC Handbook of Chemistry and Physics ,78th edition,1997-1998.B The leading figure decreases by 1.Calculate the specific gravity23/23°C of the liquid,d,as follows:d5~b2e!/~w2e!where:e=apparent mass of empty pycnometer,w=apparent mass of pycnometerfilled with water at23.0°C,andb=apparent mass of pycnometerfilled with liquid at23.0°C.If a constant-temperature water bath is available,a pycnom-eter without a thermometer may be used(compare30.2).N OTE16—One standard object which has been found satisfactory for this purpose is the Reimann Thermometer Plummet.These are normally supplied calibrated for measurements at temperatures other than23/23°C, so that recalibration is necessary for the purposes of these methods. 19.Test Specimen19.1See Section11.20.Procedure20.1The procedure shall be similar to Section12,except for the choice of immersion liquid,and the temperature during the immersed weighing(12.3)shall be2360.5°C.21.Calculation21.1The calculations shall be similar to Section13,except that d,the specific gravity23/23°C of the liquid,shall be placed in the numerator:Sp gr23/23°C5~a3d/~a1w2b!22.Report22.1See Section14.23.Precision and Bias23.1Tables1and2are based on an interlaboratory study8conducted in1985in accordance with Practice E691,involv-ing5materials tested with Test Method A by6laboratories or 4materials tested with Test Method B by6laboratories.Each test result was based on two individual determinations and each laboratory obtained four test results for each material.N OTE17—Caution:The explanations of r and R are only intended to present a meaningful way of considering the approximate precision of these test methods.The data of Tables1and2should not be applied to acceptance or rejection of materials,as these data apply only to the materials tested in the round robin and are unlikely to be rigorously representative of other lots,formulations,conditions,materials,or ers of this test method should apply the principles outlined in Practice E691to generate data specific to the materials and laboratory(or between specific laboratories).The principles of23.2-23.2.3would then be valid for such data.23.2Concept of r and R in Tables1and2—If S r and S R have been calculated from a large enough body of data,and for test results that were averages from4test results for each material,then:23.2.1Repeatability—Two test results obtained within one laboratory shall be judged not equivalent if they differ by more than the r value for that material.The concept r is the interval representing the critical difference between two test results for the same material,obtained by the same operator using the same equipment on the same day in the same laboratory. 23.2.2Reproducibility—Two test results obtained by differ-ent laboratories shall be judged not equivalent if they differ by more than the R value forthat material.The concept R is theinterval representing the critical difference between two testresults for the same material,obtained by different operatorsusing different equipment in different laboratories.23.2.3Any judgment in accordance with23.2.1or23.2.2would have an approximate95%(0.95)probability of beingcorrect.23.3There are no recognized standards by which to esti-mate bias of this test method.24.Keywords24.1density;relative density;specific gravitySUMMARY OF CHANGESCommittee D20has identified the location of selected changes to these test methods since the last issue thatmay impact the use of these test methods.D792–98:(1)An ISO equivalency statement(Note2)was added and subsequent notes were renumbered.(2)Practice E380was added to the text.(3)Paragraph9.2was revised to include the identification of a sample holder.(4)“And”was added to10.1.(5)Paragraphs12.1and14.1.4were added and subsequent paragraphs were renumbered.(6)“I r”and I R were changed to“r”and“R”in Tables1and2.(7)Section23was rewritten.D792–00:(1)Changed Note2from“There is no similar or equivalent ISO standard”to“This standard is not equivalent to ISO1183 Method A.”(2)Deleted reference to Note2in3.2.2.(3)Changed1°C to61°C in7.1.(4)Changed“if the wire is used”to“if a wire is used”in Note 13.(5)Changed the correction factor from997.6to997.5in Note 5and13.2.(6)Replaced“wire”with“sample holder”in9.3.(7)Changed accuracy from1°C to0.1°C in9.5.(8)Deleted“if the test is not performed in the standard8Supporting data are available from ASTM Headquarters.Request RR:D20-1133.laboratory atmosphere of Practice D 618”from 9.5.(9)Started first sentence with “If necessary”in 12.3.(10)Started second sentence with “In this case”in 12.3.(11)Started first sentence with “If a wire is used”in Note 10.(12)Replaced “wire”with “sample holder”in 12.4.(13)Replaced “wire”with “sample holder”in 12.5.(14)Added “is used and”between “wire”and “is”in Note 14.(15)Added 13.3and equations.(16)Added “Report the density and specific gravity with four significant figures”to 14.1.5.(17)Replaced “not fewer than four”to “ten”in 17.4.The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this ers of this standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.Your comments will receive careful consideration at a meeting of the responsible technical committee,which you may attend.If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards,at the address shown below.This standard is copyrighted by ASTM,100Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Individual reprints (single or multiple copies)of this standard may be obtained by contacting ASTM at the above address or at 610-832-9585(phone),610-832-9555(fax),or service@ (e-mail);or through the ASTM website().。
ASTM与ISO单位换算
sarlink EPDM/PP型热塑性动态硫化橡胶（TPV）是以荷兰DSM公司自产的特殊EPDM作为橡胶相，PP 作为连续相，动态硫化后得到的稳定的弹性体。
动态硫化是指在橡胶相与不能硫化的热塑性聚合物熔融密炼过程中，将橡胶进行硫化，得到粒状的硫化橡胶相，并且橡胶微区形态非常稳定，在加工过程中不会发生物化变化。
EPDM/PP型热塑性动态硫化橡胶（TPV）具有优异的物化性能。
其耐环境性能相当于通用性三元乙丙橡胶材料，耐油耐溶剂性能与通用型氯丁橡胶不相上下。
●热塑性动态硫化橡胶性能特点：EPDM/PP型热塑性动态硫化橡胶（TPV）成功地把硫化橡胶的一些特性，如耐热性能和低压缩变形性能与热塑性塑料的易加工特性结合在一起。
具有优异的抗动态疲劳性、很高的抗撕裂性、极好的耐候性、良好的耐磨性，对水基酸碱液体、极性油品具有出色的抗侵蚀能力，在－40℃～+130℃范围内均具有使用可能性。
EPDM/PP型热塑性动态硫化橡胶（TPV）所具有的耐环境性能相当于通用性三元乙丙橡胶材料，同时其耐油耐溶剂性能与通用型氯丁橡胶不相上下。
这样的极优耐环境性能独一无二的结合，使得这种热塑性橡胶适用于广泛的用途。
EPDM/PP型热塑性动态硫化橡胶（TPV）的使用性能与许多种常见的硫化特种橡胶的特性相似。
这些特性向产品设计师及材料工程师们提供了这样的机会，就是可以利用成本较低的热塑性塑料加工方式，但又不会使所希望的产品受到影响。
EPDM/PP型热塑性动态硫化橡胶（TPV）的性能特点包括以下几个方面：1、橡胶的触感，塑料的加工方法。
2、在-40℃至+130℃的有效操作范围内具有机械性能。
3、对于水基的液体、油类及碳氢化合物类具有氯丁橡胶品级的耐油耐溶剂性能。
4、压缩变形及永久变形小。
5、在150℃暴露两星期或在125℃暴露更长时间，显出其极优的耐热空气老化性能。
6、卓越的抗动态疲劳性能。
7、很高的抗撕裂强度。
8、极优的耐臭氧及耐侯性9、与聚丙烯（PP）或尼龙（PA）有极佳的粘结性。
钢材大全ASTM-A钢材标准(5)(A792-A921)
Improved Notch Toughness
A809-98
镀铝碳素钢丝
Standard Specification for Aluminum-Coated (Aluminized) Carbon Steel Wire
镀铜碳素钢丝
Standard Specification for Coppered Carbon Steel Wire
纤维增强混凝土用钢纤维
Standard Specification for Steel Fibers for Fiber-Reinforced Concrete
预应力混凝土容器用经回火的 Standard Specification for Steel Wire, Hard
Surface Acceptance Standards, Visual 准
Examination
A803/A803M-03
焊接铁素体不锈钢给水加热器 Standard Specification for Welded Ferritic
管
Stainless Steel Feedwater Heater Tubes
Chemical Composition Requirements
Standard Specification for Austenitic and
核心部件用不锈耐热钢棒,坯 Martensitic Stainless Steel Bars, Billets,
A831/A831M-95(2000)
段及锻件规格
Corrugated Steel Pipe, Pipe-Arches, and 下埋设管道用波纹钢管、管托