磁力锁产品说明书
磁力锁说明书Word版
1、吸力强，磁吸力为280kg。
本锁利用优质电工材料和先进加工工艺制造而成，外型美观，吸力强，无剩磁。
2、无机械磨损，克服一般要机械锁和电子锁缺陷，使用寿命长。
3、电源为12/24伏双直流电压入口。
4、启动电流0.45A，持续电流为0.45A，温升为室温+15℃。
锁体尺寸：250*47*25mm吸合力：280kg（静态直线）电压：DC12V\DC24V电流：480mA\240mA安装方式：明装状态指示灯：LED安全类型：断电开锁电磁锁的安装方法电磁锁(磁力锁)的标准安装方法[图]一．外开门的表面安装方法：（参照图一至图八）第一步：首先用螺丝刀打开盖板，再用六角扳手打边板，准备安装（见图一）第二步：拿出安装纸板，将纸板沿着虚线折叠按图二所示方法把纸板放到所需装锁的位置,然后把需要打孔的地方做上记号后打孔.第三步：A.继铁板的固定（参见图三）将内六角螺丝插入继铁板中，把橡胶华司置与两片金属华司之间，然后套在内六角螺丝上。
将继铁板插入门上打的三个孔中，同时把香菇头从门的另一面插入，利用六角扳手将继铁板锁在门上。
B．边板的固定（参见图三）把边板用两个半圆头螺丝固定在先前打孔的门框上（固定在边板的长形孔中）。
注意：不要将边板锁紧，让其能前后能移动以利于安位置的修正。
C．修正边板的位置使边板与继铁板的位置合适，目的使锁主体能与继铁板紧密的接触。
D：固定锁主体与边板锁紧边板的半圆头螺丝后，再锁上所有的沉头螺丝，然后再卸下半圆头螺丝，在适当的位置钻孔以便接线。
最后用六角扳手把锁主体锁在边板上。
(参见图四)第四步：按照说明书的指示接线。
第五步：盖上盖板，把小铝柱体塞进锁主体(参见图五)的螺丝孔中。
参见图六图七与图八所示为典型的外开门外置式的安装式样★安装注意事项在安装继铁板的时候，不要把它锁紧，让其能轻微摇摆以利于和锁主体自然的结合。
二、内开门的表面安装(ZL型支架的安装方法）：解决外装磁力锁的内装问题。
内开门做表面安装时需要有辅助配件来协助安装，我们选用富有装饰性的优质进口铝材来制做这种安装配件：Z&L支架。
D40ML系列RFID磁锁产品说明书
1Stainless SteelPlasticDie-cast MetalMagnetic latching combines with RFID technology to deliver high holding force and tamper resistance•RFID provide s a high degree of t a mper re s i s t a nce.•Cle a n/Sa nitize in Pl a ce – s t a inle ss s teel ver s ion s a re r a ted IP69K •LED s s upport e as y f a ult di a gno s i s •In s t a ll up to 20 s witche s in s erie s•Re s idu a l m a gneti s m a ct s as light door l a tch a fter unlocking •Two a ctu a tor type s with type 4 coding•B as ic – a ll a ctu a tor s in the s y s tem a re identic a lly coded.•Unique – every a ctu a tor i s individu a lly coded. 32,000,000 code s •Both offer toler a nce for mi sa lignment•Two s witch s ize s provide multiple holding force option s •Medium Duty-S t a inle ss S teel: F1m a x (typic a l) 600N, F zh 450N -Pl as tic a nd Diec as t: F1m a x (typic a l) 900N, F zh 675N •He a vy Duty-S t a inle ss S teel: F1m a x (typic a l) 950N, F zh 700N-Pl as tic a nd Diec as t: F1m a x (typic a l) 1500N, F zh 1150N •Three c as e m a teri a l sPl as tic, diec as t met a l, 316 s t a inle ss s teel•For u s e on m a chine s with no rundown time if power i s lo s tDiagnostic Indicator FunctionYellow LED indicates OPENS hown in Gu a rd Open Po s itionGreen LED indicates CLOSEDS hown in Gu a rd Clo s ed Po sition Switch StatusGuard Green LED Yellow LEDSafety OutputLockedClo s ed S te a dy Off Clo s ed S olenoid Power OFF (unlocked)Clo s ed Fl as hing Off Open Gu a rd Open Open Off S te a dy Open Door Forced OpenOpenOffFl as hingOpenD40ML Series2Ordering InformationSwitchesSpare ActuatorsNote:S p a re a ctu a tor s a re not a v a il a ble for uniquely coded s witche s.AccessoriesNote:1.The quick di s connect c a ble h as a n identic a l c a ble pining as the Cable Wiring on p a ge 42.Y92E-M12PUR S H8S M-L di s connect c a ble s a re a l s o comp a tible with D40ML.Case Material Holding Force F1max (typical)Actuator Type Cable Configuration Model Number316 S t a inle ssS teel (IP69K)600NUnique5m C a ble D40ML-SS2-U-5M10m C a ble D40ML-SS2-U-10MPigt a il w/ M12 Connector D40ML-SS2-U-M12B as ic5m C a ble D40ML-SS2-B-5M10m C a ble D40ML-SS2-B-10MPigt a il w/ M12 Connector D40ML-SS2-B-M12 950NUnique5m C a ble D40ML-SS1-U-5M10m C a ble D40ML-SS1-U-10MPigt a il w/ M12 Connector D40ML-SS1-U-M12B as ic5m C a ble D40ML-SS1-B-5M10m C a ble D40ML-SS1-B-10MPigt a il w/ M12 Connector D40ML-SS1-B-M12Pl as tic (IP67)900NUnique5m C a ble D40ML-P2-U-5M10m C a ble D40ML-P2-U-10MPigt a il w/ M12 Connector D40ML-P2-U-M12B as ic5m C a ble D40ML-P2-B-5M10m C a ble D40ML-P2-B-10MPigt a il w/ M12 Connector D40ML-P2-B-M12 1500NUnique5m C a ble D40ML-P1-U-5M10m C a ble D40ML-P1-U-10MPigt a il w/ M12 Connector D40ML-P1-U-M12B as ic5m C a ble D40ML-P1-B-5M10m C a ble D40ML-P1-B-10MPigt a il w/ M12 Connector D40ML-P1-B-M12Diec as t Met a l(IP67)900NUnique5m C a ble D40ML-M2-U-5M10m C a ble D40ML-M2-U-M12Pigt a il w/ M12 Connector D40ML-M2-U-M12B as ic5m C a ble D40ML-M2-B-5M10m C a ble D40ML-M2-B-10MPigt a il w/ M12 Connector D40ML-M2-B-M12 1500NUnique5m C a ble D40ML-M1-U-5M10m C a ble D40ML-M1-U-10MPigt a il w/ M12 Connector D40ML-M1-U-M12B as ic5m C a ble D40ML-M1-B-5M10m C a ble D40ML-M1-B-10MPigt a il w/ M12 Connector D40ML-M1-B-M12Product Description Model Number S t a inle ss S teel; IP69K; 950N; B as ic Code; Actu a tor D40ML-SS1-B-ACTS t a inle ss S teel; IP69K 600N; B as ic Code; Actu a tor D40ML-SS2-B-ACT Diec as t Met a l; IP67; 1500N; B as ic Code; Actu a tor D40ML-M1-B-ACTDiec as t Met a l; IP67; 900N; B as ic Code; Actu a tor D40ML-M2-B-ACTPl as tic; IP67; 1500N; B as ic Code; Actu a tor D40ML-P1-B-ACTPl as tic; IP67; 900N; B as ic Code; Actu a tor D40ML-P2-B-ACTProduct Description Model Number Quick Di s connect C a ble, 8-pin M12 to Flying Le a d s, PVC J a cket, 5 Meter Length D40ML-CBL-M12-5M Quick Di s connect C a ble, 8-pin M12 to Flying Le a d s, PVC J a cket, 10 Meter Length D40ML-CBL-M12-10MD40ML Series3SpecificationsNote:When the product u s e devi a te s from the s e ass umption s (different lo a d, oper a ting frequency, etc.) the v a lue s mu s t be a dju s ted a ccordingly.Codes and StandardsIEC 60947-5-3:2013, EN 60947-5-1:2004 + AC:2005 + A1:2009, EN 60947-1:2007 + A1:2011, EN I S O 13849-1:2008 + AC:2009, EN 62061:2005 + AC:2010 + A1:2013, I S O 14119:2013, UL508Safety Classificationand Reliability Data Minimum Switched Current 10VDC 1mA Dielectric Withstand 250VAC Insulation Resistance 100M ΩShock Resistance 11m s 30GVibration Resistance 10 to 55Hz, 1mm a mplitude Switching Distance S a o 1mm Clo s e; S a r 10mm OpenMisalignment Between s witch a nd a ctu a tor, 2mm in a ny direction Switching Frequency 1.0Hz m a ximum Response Time (On –> Off)10m s m a x.Operating Time (Off –> On)150m sApproach Speed200mm/m to 1000mm/sBody MaterialD40ML-P_: Pl as ticD40ML-M_: Diec as t Met a lD40ML-SS _: 316 S t a inle ss S teel Actu a tor S e a l: S iliconeEnc a p s ul a tion: High Temper a ture Epoxy Operating Temperature Range–25 to 40°CAmbient Operating Humidityup to 90% a t 25 ~ 40°CEnclosure Protection IP67 (Pl as tic or Diec as t Met a l)IP69K (S t a inle ss s teel ver s ion s with flying le a d s )Cable Type PVC 8 core, 6mm outer di a meter Mounting Bolts 2 × M5 Tightening torque 1.0Nm Mounting Position AnyPower Supply 24VDC ±10% (s elv / pelv)Power ConsumptionUnlocked: 50mA m a x.Locked:- Medium Duty 325mA m a x. - He a vy Duty 500mA m a x.Holding ForceMedium Duty- S t a inle ss S teel: F1m a x (typic a l) 600N, F zh *1 450N - Pl as tic a nd Diec as t: F1m a x (typic a l) 900N, F zh 675N He a vy Duty- S t a inle ss S teel: F1m a x (typic a l) 950N, F zh 700N- Pl as tic a nd Diec as t: F1m a x (typic a l) 1500N, F zh 1150N *1A new te s t h as been introduced with the coefficient 1.3. A device with a s pecified m a ximum holding force (F zh ) of 500N need s to hold up a force te s t (F1m a x ) a t 650N.According to the s t a nd a rd the locking force F zh s hould be s t a ted for every gu a rd locking s witch.Max. Switched Current (Outputs)200mA (min. intern a l re s i s t a nce 8.5 Ohm s )Auxiliary Signal+24 VDC (Door Open)Characteristic Data according to EN ISO13849-1PLe: If both ch a nnel s a re u s ed in combin a tion with a S IL3/PLe control device C a tegory: C a t. 4MTTFd: 1100aDi a gno s tic Cover a ge DC: 99% (high)Number of oper a ting d a y s per ye a r: d op = 365d Number of oper a ting hour s per d a y: h op = 24h B10d: Not mech a nic a l p a rt s implemented Characteristic Data according to IEC62061 (used as a sub system)Sa fety Integrity Level: S IL3PFH (1/h): 4.77E-10 Corre s pond s to 4.8% of S IL3PFD: 4.18E-05 Corre s pond s to 4.2% of S IL3Proof Te s t Interv a l T 1: 20aInformation with regard to UL508U s e LVLC or Cl ass 2 s upply. Type 1 enclo s ure.Risk Time in accordance with EN 60947-5-3150m s (s witching off del a y a t remov a l of a ctu a tor)D40ML Series4Cable WiringTypical Operating Distance (Front Approach)Note:DO NOT u s e s witch a nd a ctu a tor as a gu a rd door stop.Solenoid Supply 24 VDCAuxSafety Output 2Safety Output 1External Supply 24 VDCNon-Contact RFID Locking Switch Wiring DiagramQuick Connect(CC)M12 8-way maleplugConductorColorsFunction Power Rating8Or a ngeApply Lock(24VDC ±10%)50mA M a x5BrownAuxili a ry S ign a l(Door Open/Clo s ed)+24VDC(200mA)4Yellow Sa fety Output 2200mA M a x6Green Sa fety Output 21White Sa fety Output 1200mA M a x7Bl a ck Sa fety Output 13Blue0VDC500mA M a x2Red+24VDC ±10%Misalignment mmDistance mmD40ML Series5Dimensions(Unit: mm)D40ML Medium Duty SwitchD40ML Heavy Duty SwitchInstallation:•In s t a ll a tion of a ll D40ML s erie s sa fety s witche s mu s t be in a ccord a nce with a ri s k ass e ss ment for the individu a l a pplic a tion.•The u s e of a sa fety rel a y i s required for monitoring RFID coded s witche s . The s e rel a y s monitor two redund a nt circuit s as per I S O13849-1 for up to PLe/C a tegory 4 protection.•D40ML s erie s s witche s a re de s igned to oper a te with mo s t du a l ch a nnel sa fety rel a y s to sa ti s fy EN60947-5-3.•M5 mounting bolt s mu s t be u s ed to mount the s witche s . Tightening torque for mounting bolt s to en s ure reli a ble fixing i s 1.0 Nm. Alw a y s mount on non-ferrou s m a teri a l s .•Do not mount a dj a cent s witche s or a ctu a tor s clo s er th a n 30mm.•To a chieve nomin a l holding force en s ure f a ce-to-f a ce a lignment of m a gnetic p a rt s .•After in s t a ll a tion a lw a y s check e a ch s witch function by opening a nd clo s ing e a ch gu a rd individu a lly in turn a nd en s uring th a t the Green LED on the s witch a nd the LED s on the sa fety rel a y a re illumin a ted when the s witch i s clo s ed a nd a re extingui s hed when the s witch i s open. Check th a t the m a chine s top s a nd c a nnot be re-s t a rted when e a ch s witch i s open.Maintenance/Safety Checks: Monthly: Check a lignment of a ctu a tor a nd look for s ign s of mech a nic a l d a m a ge to the s witch c as ing or c a ble s .The sa fety function s a nd mech a nic s mu s t be te s ted regul a rly. For a pplic a tion s where infrequent gu a rd a cce ss i s fore s ee a ble, the s y s tem mu s t h a ve a m a nu a l function te s t to detect a po ss ible a ccumul a tion of f a ult s . At le as t once per month for PLe C a t3/4 or once per ye a r for PLd C a t3 (I S O13849-1). Where po ss ible it i s recommended th a t the control s y s tem of the m a chine dem a nd s a nd monitor s the s e te s t s , a nd s top s or prevent s the m a chine from s t a rting if the te s t i s not done. (I S O14119). Check th a t the m a chine s top s a nd c a nnot be re-s t a rted when e a ch s witch i s open.NOTE: The sa fety output s will only clo s e when the a ctu a tor i s in pl a ce a nd the lock m a gnet i s energized. Forcing open of the lock will c a u s e the sa fety output s to open.IMPORTANT: The gu a rd holding h as no interlock function. The Ri s k A ss e ss ment for the p a rticul a r a pplic a tion s hould include the ri s k of s p a re a ctu a tor s . S p a re a ctu a tor s s hould not be re a dily a v a il a ble a nd mu s t be s ecurely controlled. Record a ny RFID code s as required by f a ctory rule s or with reference to a ny ri s k ass e ss ment for the p a rticul a r a pplic a tion a nd u s er loc a tion.Fixing Holes for M5 ScrewsACTUATORSWITCHFixing Holes for M5 Screws64648896Ø 5058.5060.50411R 32437523225445232626.50SWITCH Fixing Holes for M5 ScrewsFixing Holes for M5 ScrewsACTUATOR11579.5010575.50Ø 6544116666Ø 76Ø 805252443228.504338631D40ML Series6Wiring OptionsD40ML to G9SE-201(up to Safety PLe acc. EN ISO13849-1)D40ML to G9SE-201 - Series Connections (up to SafetyPLd acc. EN ISO 13849-1, maximum 20 switches)M: 3-phase motorTerms and Conditions AgreementRead and understand this catalog.Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments.Warranties.(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanshipfor a period of twelve months from the date of sale by Omron (or such other period expressed in writingby Omron). Omron disclaims all other warranties, express or implied.(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENT ATION, EXPRESS OR IMPLIED, ABOUTNON-INFRINGEMENT, MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THEPRODUCTS. BUYER ACKNOWLEDGES THA T IT ALONE HAS DETERMINED THA T THE PRODUCTS WILLSUIT ABL Y MEET THE REQUIREMENTS OF THEIR INTENDED USE.Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) thenon-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty.See /global/ or contact your Omron representative for published information.Limitation on Liability; Etc.OMRON COMP ANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENT AL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.Suitability of Use.Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.NEVER USE THE PRODUCT FOR AN APPLICA TION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THA T THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THA T THE OMRON PRODUCT(S) IS PROPERL Y RA TED AND INST ALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.Programmable Products.Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.Performance Data.Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.Change in Specifications.Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product.Errors and Omissions.Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions.Authorized Di s tributor:In the interest of prod u ct improvement,specifications are s ub ject to change witho u t notice.Cat. No. F22E-EN-01C0421(0613)© OMRON Corporation 2013-2016 All Rights Reserved.OMRON Corporation Indu s trial Automation CompanyOMRON ELECTRONIC S LLC2895 Greenspoint Parkway, S u ite 200 Hoffman Estates, IL 60169 U.S.AT el: (1) 847-843-7900/Fax: (1) 847-843-7787Regional Headquarters OMRON EUROPE B.V.Wegalaan 67-69, 2132 JD Hoofddorp The NetherlandsTel: (31) 2356-81-300/Fax: (31) 2356-81-388 Contact: www.indu s trial.omron.euOMRON A S IA PACIFIC PTE. LTD.No. 438A Alexandra Road # 05-05/08 (Lo bb y 2), Alexandra T echnopark, Singapore 119967T el: (65) 6835-3011/Fax: (65) 6835-2711OMRON (CHINA) CO., LTD.Room 2211, Bank of China T ower, 200 Yin Cheng Zhong Road,P u Dong New Area, Shanghai, 200120, China T el: (86) 21-5037-2222/Fax: (86) 21-5037-2200。
磁力锁 、电插锁 、电动开门机说明书
磁力锁电插锁电动开门机规格书技术参数（DAIC-MJ-DCLS）产品名称：280KG单门磁力锁（带信号输出)产品图片：产品概述：磁力锁（或称电磁锁）的设计和电磁铁一样，是利用电磁的原理，当电流通过硅钢片时，磁力锁会产生强大的吸力紧紧吸住铁板；只要非常小的电流就会让磁力锁产生很大的磁力，从而能有效地控制门的开关。
深圳多奥磁力锁采用国际领先的生产和封装工艺，不仅让磁力锁表面抗氧化能力达到国际领先水平，还使磁力锁的拉力远高于同类产品达20%以上。
我们的产品已远销到全球六十个国家或地区，且广泛应用于机场、地铁、银行、监狱、智能大厦、智能小区等重要场所，为全球用户提供方便、快捷、智能化的出入口管理锁具，受到了用户的广泛好评和青睐。
产品优势：◆ 250KG±10%静态直线拉力◆ 可自行设定12VDC±10% 或24VDC±10%◆ 内置反向电流保护装置（MOV）◆ 防残磁设计，防磨损材料制造◆ 铝外壳采用高强度合金材料◆ 双重锁体绝缘处理◆ 完全电磁吸力工作，不存在机械故障技术参数：锁体尺寸：长250x宽47x厚26(mm) 吸板尺寸：长180x宽38x厚11(mm) 工作电压：DC12V±10%/DC24V±10% 工作电流：480mA±5%/240mA±5%信号输出：锁状态信号输出延时开门：无安全类型：断电开门适用门型：木门\玻璃门\金属门\防火门等质量认证：CE/FCC/CMA/ROHS 选配支架：DA-280L/280U/280ZL产品尺寸：产品规格书（DAIC-MJ-LXS）产品名称：灵性锁（电机锁)产品图片：产品概述：电机锁(或称灵性锁)的设计有效结合了传统电控锁及磁力锁的优点，克服了电控锁噪音过大、磁力锁耗电等方面的不足而开发的新产品，电机锁与电控锁和磁力锁相比较，它的性能更加的完善、优点更加明显，可与楼宇对讲、门禁等智能化系统配套使用。
Forcelock 3000系列电磁锁说明书
TMSM•High Security• 12/24 VDC/VAC• One Piece Housing• FasTrak Mounting• Lifetime Warranty3000S e r i e s1500L b s.H o l d i n g F o r c eE l e c t r o m a g n e t i c L o c k sDescriptionThe 3000 Series is a full size 1500 lbs. holdingforce electromagnet. It is designed for lifesafety and high security on rated or nonrateddoors and frames. Specify for commercial,industrial, or institutional openings wheremaximum security and durability is required.All 3000 Series locks are designed for ease ofinstallation with DynaLock’s exclusive FasTrakmounting system, field selectable voltage, andconvenient wiring compartments. Optionalintegrated door and lock status sensors allowremote monitoring without the need to installseparate “door contacts”.The 3000 Series is offered in single, double, andsplit armature models for both outswinging andinswinging doors. The coil and housingassembly mounts rigidly to the door frame whilethe armature mounts to the door in a mannerthat allows it to pivot slightly to compensate fordoor irregularities. When the door is closed andthe lock is energized the armature ismagnetically bonded to the lock face, thussecuring the door without utilizing any movingparts.Standard Features• One Piece Housing made from high strengthaluminum. A seamless housing means maximumresistance to weather and tampering.• FasTrak Mounting: Speed up installation by mountingthe FasTrak channel to the frame first. Lock can then beattached and removed with ease.• Universal Design: Lock handing can easily be reversedin the field, allowing placement of the coil adjacent to thevertical jamb where it will exert the most efficient force.• Low power consumption conserves energy, reducesoperation cost, and extends battery backup time.• A totally plated coil and armature provides protectionagainst corrosion.• A narrow backset of 1-1/2” may mean the eliminationof other mounting brackets or filler plates.• No residual magnetism - the door releases withoutdelay when lock is de-energized.• Built-in spike suppression protects other solid statecomponents within the system from damage when the lockis de-energized.•Lifetime Warranty - American Made in the USA byDynaLock, with over 20 years experience in themanufacture of electromagnetic locks.NYC Mea #23-92-ECSFM23000 Single Outswinging DoorSingle coil. Mounts to the underside of the frame header .1500 Lbs. Holding Force.3001 Double Outswinging DoorSingle coil with double (split) armature. Mounts to the underside of the frame header . Recommended for traffic control only. 750 Lbs. holding force per leaf.3002Double Outswinging DoorDouble coil. Mounts to the underside of the frame header .1500 Lbs. holding force per leaf.3002-TJ32 Double Inswinging DoorDouble coil. Mounts to the face of the frame header .1500 Lbs. holding force per leaf.3000-TJ30 Single Inswinging DoorSingle coil. Mounts to the face of the frame header .1500 Lbs. holding force.3001-TJ31 Double Inswinging DoorSingle coil with double (split) armature. Mounts to the face of the frame header . Recommended for traffic control only.750 Lbs. holding force per leaf.TM SM3Options23/4”SEXNUT LOCK11/2”23/16”MountingINSWINGING DOOR SIDE VIEW OUTSWINGING DOOR SIDE VIEWARMATURELOCK11/2”SEX NUT27/16”ADJUSTABLE23/4”ARMATUREMOUNTINGBRACKET WiringConnectionsShown with all options.CLHDSMDSM2HSMHSM2VOPVOP2LCLCBLEDLED2LPLP2OFAS FCUSTOM LENGTH HOUSING - See back page.DOOR STATUS SWITCH - Signals door closed or ajar. SPDT contacts.DOOR STATUS SWITCH - For the 3002 models.HIGH SECURITY MONITOR - Includes the following:HIGH SECURITY MONITOR - For the 3002 models.VALUE OPTION PACKAGE - Includes the following:VALUE OPTION PACKAGE - For the 3002 models.A 3000 Series coil assembly supplied in a 2000 Series multi-piece housing.BASIC LOCK LESS CIRCUIT BOARD - Coil and housing with flying leads.BI-COLOR LED - For local signaling of lock status. (Requires HSM or VOP option)BI-COLOR LED’S(2) - For the 3002 models. (Requires HSM2 or VOP2 option)*****************************(SingleLock)******************************(DoubleLock)OFFSET ARMATURE - For aluminum storefront doors. Mounting hole is higher to avoid top rail drilling problems.SPECIAL FINISH - Standard finish is US28 Satin Aluminum. Special anodized finishes, see price book. Notes: DSM, HSM, VOP and LED options not available on 3001 split armature models or with LCB option.5”DOOR STATUS SWITCH - Signals door closed or ajar. SPDT contacts.DYNASTAT FORCE SENSOR - Indicates efficient magnetic bond. SPDT contacts.DOOR STATUS SWITCH - Signals door closed or ajar. SPDT contacts.DYNASTAT FORCE SENSOR - Indicates efficient magnetic bond. SPDT contacts.ANTI-TAMPER SWITCH - Signals removal of the housing cover. SPDT contacts.RELOCK TIME DELAY - Adjustable 1-80 seconds.ARMATURESpecifications3000S e r i e s E l e c t r o m a g n e t i c L o c kHolding Force:Lock Size:3002, 3002TJ32 All othersArmature Size:3001, 3001TJ31 All othersLock Weight:1500 Lbs. Each Coil11/2”D x 23/4”H x 22”L11/2”D x 23/4”H x 11”L1/2”D x 23/8”H x 35/8”L1/2”D x 23/8”H x 73/8”L3000, 3001 10Lbs. / 3002 19Lbs. 3000TJ30, 3001TJ31 12Lbs. 3002TJ32 23Lbs.MECHANICALInput Voltage: Current Draw:Contact Ratings: Coil Resistance:12 or 24 VDC/VAC (Field Selectable)0.42A @ 12V Each Coil0.21A @ 24V Each CoilDSM - 0.25A @ 24VDC/VACDYN - 1A @ 24VDC/VACATS - 0.5A @ 24VDC/VAC53.2 Ohms (+/- 10%) Wht/Wht, Blk/BlkFeaturingDyna LifeLifetime WarrantyAccessories• 4000 Series Installation AccessoriesFiller Plates: Extend the door stopAngle Brackets: Extend the header• 5000 Series Power SuppliesSolid state power supplies provide propervoltage, time delay and battery backup ifrequired.• 6000 Series Exit ControlsPush-buttons in a variety of switchingconfigurations and exit sensor bars.• 7000 Series Keyswitches and KeypadsKeyswitches accept most mortise cylinders for controlled access.Rugged digital entry keypads.• 8000 Series ConsolesDesktop, slope front and rack mount fabricated to customer specifications.Custom Length HousingsOptional custom length housings are ordered in addition to the lock itself. They are used to provide an unbroken sight line across the header or vertical jamb, for a less conspicuous installation.3500 Single door. One horizontal lock LHR 30” to 48”.3600 Single door. One horizontal lock RHR 30” to 48”.3700 Single door. Two vertical locks up to 96”.3800 Double door. Two horizontal locks up to 96”.ELECTRICALFinish:US28 Satin Aluminum with clear anodizeOther Finishes AvailableELECTRICAL3500360038003700。
SL-200电磁锁说明
香菇頭螺絲
橡皮墊片 吸吸附附板板螺絲 M8
（注意為了彌補門的不對稱，吸附板與門㆗間必須 套㆖橡皮墊片使之能輕微晃動，以便與電磁鎖表面 能夠緊密相互吸合，如此才能發揮最大吸力。）
從香菇頭螺絲處鑽 12mm的孔
[圖㆒]
鑽約8mm的孔貫穿門
定位栓 (要先 敲入吸附板)
[圖㆓]
門 板
能輕微晃動
Page 2
步驟 4 : 選擇正確的電壓及開門延遲。
5.0 SEC
9.0 SEC
ON
開門延遲時間
12
調整
門框
主體固定板 電磁鎖主體
吸附板
※電磁鎖與吸附板正確關㆖時RELAY輸出為N.O.接點 (且指 示燈由紅色轉為綠色) ※RELAY 輸出端規格:1A/30VDC或0.5A/125VAC
步驟 5 :
橡皮墊圈
門板
[安裝完成圖]
把電磁鎖固定在固定板㆖，並且確認在門關㆖時電磁鎖能夠與吸附板輕易㆞吸 合以避免不必要的危險及聲音。
(5)安裝外拉門時可搭配EB/SB系列吸附板安裝架(附圖所示),方便施工。
木門
木門
玻璃門
[EB-200/220 槽型外掛架]
[SB-200/220 平板外掛架]
[UB-200/220 玻璃夾]
常 見問題
◆ 吸力不足? 1.請檢查電壓是否正常2.電壓調整是否正確3.磁力鎖與吸附板是否緊密結合。
◆ 門關㆖後,標準型或豪華型指示燈不會變成綠燈? 1.請檢查吸附板是否安裝在正確位置㆖,是否可晃動微調與磁力鎖緊密結合,因為當吸附板未與磁力鎖本體作緊密結合 時,指示燈不會轉變成綠色,因為它表示門未關㆖或未關好。 2.若吸附板在正確位置㆖,也緊密結合,但仍無法變成綠燈時,請檢查電壓是否足夠,電壓JUMP是否調整正確另外也請檢 查磁力鎖與吸附板兩者表面是否有異物附著在㆖面,若有請將之清除,因為灰塵或生鏽物等均會影響到吸力而導致燈不 會變化。
磁力锁使用说明书
磁力锁使用说明书(HT280G/HT280Q/HT300M)一、适用范围：1、门类型：木门、铁门、不锈钢门、玻璃门2、控制方式：楼宇对讲系统、门禁系统二、产品特点：1、电磁部份选取优质电磁专业材料(纯铁)及工艺制造。
2、拉力强、无残磁、用电少、无机械磨损、使用寿命长。
三、技术参数：型号标准电压工作电流抗拉力上锁方式安装方式极性HT280Q DC12V 0.26A 260kg-280kg 通电上锁嵌入式无HT280G DC12V 0.3A 280kg 通电上锁外挂式无HT300M DC12V 0.3A*2 250kg*2 通电上锁外挂式有型号尺寸HT280Q 250mm¡50m m¡26m mHT280G 210mm¡49m m¡26m mHT300M 500mm¡48m m¡25m m四、接线说明：1、当电锁工作时，若锁体与吸板接触不好，须从新调整吸板与锁体的位置，使锁体与吸板保持全面接触；2、直流DC12V供电, 接线不分极性；3、不含电子电路板.五、注意事项：1、选择功率够大的电源，线材必须大于0.75MM (电源的输出电压严格控制在12V+_10%内)。
2、锁体与连板的镙丝必须上紧，三个月检查锁体与吸板的固定情况；3、安装其间要小心以免损伤吸板和锁体的电镀层，否则影响正常使用、吸力、寿命；4、吸板和锁体的是否全面接触，接触面积的多少直接影响吸力大小；5、吸板与门之间必须加装一个橡皮垫让吸板保持适当的弹性，吸板的牵拉镙丝不要上得太紧，要让橡皮垫保持适当的弹性；6、吸板不能焊接到门体上，这样影响磁力锁的正常使用；7、使用前请将锁体表面的防锈油用棉布擦干净，不能用碱性或刺激性的清洁剂清洁。
安装吸板注意事项：1. 配件包内的橡皮圈一定要安装在吸板与门之间，能吸收关门时所受冲击力和平衡两者之间的接触。
2. 固定吸板的镙丝不能过于上紧，要让橡皮圈保持适当的弹性，使吸板能随吸板自动调整到正确的位置才能发挥最大的吸力。
320M（MiniLine，电磁锁）：一款中等安全程度的滑动门电磁锁说明书
*30020*30020 Model 320M320 Series Electromagnetic LockInstallation InstructionsDoor and frame preparationUsing mounting block:Door face1 1/4"5/8"1 1/16"2places:Outside: Ø 1/2" Inside: Ø 9/32",countersink 82º to 15/32"Magnet and armatureL Different sizeholes are used for the inside and outside of door.Door edge Magnet and armature4 5/16" if DSM removed 1 9/16"1 1/32" added to top or bottom ofcutout for total length of 5 11/32" with DSMRemoved material OR Recessed areaMounting directly into sliding door:Door face11/16"Reinforcement byothers, inside door cavityMagnet and armatureDoor edgeMagnet and armature4 5/16" if DSM removed1 15/16"2 5/32"1 9/16"1 1/32" added to top or bottom of cutout for total length of 5 11/32" with DSM3 7/8"Ø 1/4" 2 placesDrill and tap 5/16-183/8" min. full threadRemoved material OR Recessed areaFrame: Standard metalMagnet and armature1 17/32"Max.7/8"8 5/16"3/8"3/8"7 1/16"Ø 3/16" countersink 82º to Ø 5/16"6 placesRemoved material OR Recessed area 1 1/4" Deep Min.Frame: Wood/non-hollowMagnet and armature1 17/32"5/8"7" 6 1/2"Recessed area 1 1/4" DeepFasteners not included. Useappropriate fasteners to ensure magnet is securely installed.Recessed 1/8" two places6" Max.Installation1 Install magnet into frame.1a Orient mounting blocks as shown for your installation. Themagnet should be flush with frame after installation.1b Install magnet into frame.1c Magnet should be completely flush with frame.2 Install armature into door.Using mounting block:2a Install armature mounting block if the door has not been otherwise reinforced.InsideOutside2b Install armature.Mounting directly into sliding door: 2a Install armature.OR3Complete wiring for lock.Use configuration appropriate for your installation.Fig. 1: 24V with MBS, ATD and/or DSMM C DMAGNETN.C.C N.O.+-WHT -N.O.BLK -C RED -N.C.RED BLK BLU WHT ORN ORNBLU BRN GRN RED BLKRED BLK BLU WHT WHT WHTTAG LTRC D MDESCRIPTION COIL WIRES DSM WIRES MBS WIRESTAG LEGENDMBS (OPTION)SPDT DRY CONTACTSEE DESCRIPTION FOR DETAILSSTATION CONTROL (NOT INCLUDED) NORMALLY CLOSED DRY CONTACTS24VDC POWER INPUTDSM (OPTION)SPDT DRY CONTACTS SEE DESCRIPTION FOR DETAILS CONTROL MODULEATD (OPTIONAL)Switch must be set to C1 (24V)(factory default)C1C2switch flushswitch recessedFig. 2: 12V with MBS, ATD and/or DSMM C DSTATION CONTROL (NOT INCLUDED)NORMALLY CLOSED DRY CONTACTS12V DC POWERINPUTN.C.C N.O.+-MBS (OPTION)SPDT DRY CONTACTSSEE DESCRIPTION FOR DETAILSDSM (OPTION)SPDT DRY CONTACTS SEE DESCRIPTION FOR DETAILSWHT -N.O.BLK -C RED -N.C.BLU BRN GRN RED BLKN/C N/CRED BLK BLU WHT ORN ORNRED BLK BLU WHT WHT WHTTAG LTRC D MDESCRIPTION COIL WIRES DSM WIRES MBS WIRESTAG LEGENDMAGNETCONTROL MODULEATD (OPTIONAL)Switch must be set to C2 (12V)C1C2switch flushswitch recessedFig. 3: 12V or 24V without MBS or ATDM C DMAGNETWHT -N.O.BLK -C RED -N.C.RED BLK BLU WHT WHT WHTTAG LTRC D MDESCRIPTION COIL WIRES DSM WIRES MBS WIRESTAG LEGENDDSM (OPTION)SPDT DRY CONTACTS SEE DESCRIPTION FOR DETAILS12V OR 24V DC POWER INPUT+-STATION CONTROL (NOT INCLUDED) NORMALLY CLOSED DRY CONTACTS© Allegion 2019Printed in China 30020 Rev. 08/19-j4Adjust lock as necessary.ATD (Adjustable Time Delay)ATD can be set to delay relock from 0 to 30 seconds. To increase time, turn adjustment potentiometer clockwise (CW). To decrease time, turn adjustment potentiometer counterclockwise (CCW). ATD will operate whenever input power is interrupted and then reapplied. For potentiometer location, see Fig. 1 and Fig. 2.DSM (Door Status Switch)The DSM provides a signal to indicate whether door is open or closed. The lock’s mounting instructions should be followed closely to ensure reliable performance. DSM provides a signal via a set of form “C” dry contacts rated 100mA, resistive at 24VDC. These contacts, which are labeled in an open door condition are accessed by three (3) wires:• White - N.O. (Normally Open)• Black - C (Common)• Red - N.C. (Normally Closed).When the door closes, black and white wire contacts close and black and red wire contacts open. See Fig. 4, Fig. 5 and Fig. 6.N.O. (WHITE)C (BLACK)N.C. (RED)Fig. 4: Contact configuration when door is open N.O. (WHITE)C (BLACK)N.C. (RED)Fig. 5: Contact configuration when door is closedGRN.O. (WHITE)C (BLACK)N.C. (RED)To low voltage power source compatible lamp voltage requirements.Fig. 6: Wiring example of contacts used to switch externalindicators (not included). Shown door closed. Green LED lit.MBS (Magnetic Bond Sensor)The MBS senses whether sufficient magnetic holding force exists for adequate locking. It responds to low line voltage, foreignmaterials in magnetic gap, and damaged or dirty magnet and/or armature surfaces. The MBS option provides a signal via a set of form “C” dry contacts rated 1A @ 30VDC resistive load maximum. Dry contacts, which are labeled in a deenergized/no bond condition are accessed by three (3) wires:• Green - N.O. (Normally Open)• Brown - C (Common)• Blue - N.C. (Normally Closed)Once the lock is energized with magnet and armature properly bonded, C and N.O. contacts close and C and N.C. contacts open. See Fig. 7, Fig. 8 and Fig. 9.N.O.(GREEN)C (BROWN)N.C.(BLUE)Fig. 7: Contact configuration when insufficient or no bond existsN.O.(GREEN)C (BROWN)N.C.(BLUE)Fig. 8: Contact configuration when sufficient bond existsN.O.(GREEN)C (BROWN)N.C.(BLUE)Wiring example of contacts used to switchRGTo low voltage power source compatible with lamp voltage requirements.Green -Lit when sufficient bond exists Red -Lit when insufficient bond existsFig. 9: Wiring example of contacts used to switchexternal indicators (not included). Shown door closed. Green LED lit.。
磁力锁产品说明书
磁力锁产品说明书
感谢您购买本公司生产的磁力锁。
为了更好地使用本产品，请在开始安装之前仔细阅读本说明书内容。
一、概述:
本磁力锁主要主材料来自国外进口,产品质量稳定可靠；符合公安消防要求；符合环保要求，工作时无噪声；防腐蚀，锁体经过特殊防锈处理；耐磨损，不会因为机械零件的磨损引起这种故障。
二、主要技术参数:
序号项目指标
1工作电压DC12V±10%
2工作电流350mA
3工作环境湿度<90%
4工作环境温度-20℃~50℃
5吸力280KG
6开锁方式通电上锁，断电开锁
7门状态信号可选
三、安装步骤图:
四、注意事项：
1．磁力吸板的螺丝不要上的太紧，要让橡胶垫圈保持适当的弹性，使磁力吸板吸力自动调整到正确的位置。
2．磁力吸板安装要与锁体对正，以免吸力不够。
3．磁力锁工作时会产生较强磁场，请勿将对磁敏感元件靠近锁体。
磁力锁使用说明
软件
L
标准模式O非标准模式
产品名称
电子锁使用说明书
主板编码
753-5
版本
A/0
系列编码
880-2
页次பைடு நூலகம்
1/2
智能锁出厂统一密码:客密码为“8888”，主密码为“12345678”。
一、客密码设置及开箱
1.客密码设置：
可在开箱状态下自行设置任意4位密码，按“LOCK”键关箱锁定。
例：按数字“1111”按“LOCK”键显示CLOS再显示密码“1111”
2.按“CLOCK”键，设定年、月、日、时、分
以下“★”表示要输入内容：
年：“YE★★”、月：“ON★★”、日：“DA★★”、
小时：“HO★★”、分：“IN★★”。
例：2003年09月28日16时18分
YE03、ON09、DA28、HO16、IN18
3.按“MENU”键，进入查询开箱记录，显示“PAGS”
按“MENU”键，显示“★★★★”，前二位表示月份,后二位表示日期。
按“MENU”键，显示“★★★★”，前二位表示小时，后二位表示分钟。
按“CLR”键，退出查询。
主密码开箱记录“Code”
例：查询第二条开箱记录：输入主密码“12345678”在“9-1”计数期间
按“MENU”显示“PAGE”按“UP”二次显示“P002”
在输入过程中按“CLR”键，表示清除。
三、工作条件
电 源：四节5号“AA”碱性电池 功 耗：<10uA
工作温度：-10℃-+70℃ 工作湿度：10%-90%RH
密码容量：≥104
开箱记录：14条(120条)
四、维护、保养及注意事项
电磁锁M490DE安装说明书
Front Side of Lock
Wiring Cover
End Block
b. Remove board.
WARNING
Warnings indicate potentially hazardous conditions, which if not avoided or corrected, may cause death or serious injury.
CAUTION
Cautions indicate potentially hazardous conditions, which if not avoided or corrected, may cause minor or moderate injury.
Sex Nut
* Two armature bolts may be included in the package, but only one is used. There may be one left over after proper installation. ** Screws for both reinforced metal and sheet metal are included. Some screws will be left over after proper installation. See individual steps for screw identification.
interference that may cause undesired operation. Changes or modifications not expressly approved by party responsible for compliance could void user’s authority to operate equipment.
标准电磁锁-10010 20 40 60型号安装说明书
REV 1.0Fitting Instructions for Standard Electro Magnetic Lock - Model 10010/20/40/60The fixing option you use will depend on the height and depth of the Door frame header.1. Fig. 1 shows an outward opening door with a deep frame header. The Standard Flat Mounting plate which comes with the magnet can be used if measurement 'A' is at least 60mm (2.36") and 'B' is at least 80mm (3.15").2. Fig. 2 shows an outward opening door with a shallow frame header. The optional Transom 'L' bracket (AC-EMBR006) must be used if measurement 'A' is less than 45mm (1.75") and 'B' is at least 80mm (3.15").3. Fig. 3 shows an inward opening door for which the 'Z&L' bracket set must be used. The optional 'Z&L' bracket set (AC-EMBR026F) must be used if measurement 'A' is up to 20mm (0.78") and 'B' is at least 60mm (2.36"), 'C' must be at least 60mm (2.36").If any of the above measurement requirements do not match you may need to use a different magnetic lock . Important points to consider during installation:1. Check that the door is properly aligned with the door frame when in the closed position. If the gap around the door and frame is not equal the magnet should not be fitted until the door is correctly aligned.2. Always handle the equipment with care as damage to the mating surfaces of the magnet or armature plate may reduce locking efficiency.3. Ensure the correct screws and fittings from the fixing pack are used as incorrect screws or fittings will affect the operation of the magnetic lock and armature plate.4. It is essential that the magnetic lock and armature plate are correctly aligned and installed correctly.5. When using the template the door must be in the closed and latched position.6. Thread lock must be applied to all threads on the magnetic lock and fixing brackets and the armature Standard magnetic lock is suitable for Timber or Aluminium Entry and Exit doors to provide controlled access via an Access Control System. It should not be used as the only lock securing the door, a mortice deadlock or similar should also be fitted.It can also be used on an Internal door when a stronger holding force may be needed.It is essential that the Header Frame and Top Rail of the door are strong enough to accommodate the magnet and Armature Plate, if in doubt consult door and frame supplier for advice.NOTE: THIS LOCK IS SUITABLE FOR SOLID DOORS 35-53mm THICK OR HOLLOW DOORS 35-46mm THICK.A B C D E F G H I J LM N OFIXING PACK CONTENTS QTY M8 Counter sunk Allen bolt 50mm (2") long1Dome nut 41 x 12mm (1.6x0.5") ChromeAluminium spacer 43 x 16mm (1.7x0.63") (For hollow doors)No 10. 32mm (No 10x1.25") Csk wood screwNo 8. 15mm (No 8x0.6") Csk wood screw (for slotted holes)Steel washer 22mm (0.87") diameter (for Armature plate)Rubber washer 15mm (0.6") diameter (for Armature plate)*Guide pin 16 x 5mm (0.63x0.2") (split dowel)M5 x 8mm (0.31") Csk Machine screw M4 x 25mm (0.5") Csk screw (thread relieved)Allen key wrench 5 x 80mm (0.2x3.15")M8 Nylock nut (for use with 'Z' bracket)M6 Allen bolt 36mm (1.42") long Incl head**Metal spacer 21 x 9mm (0.83x0.35")**1111822222222A B C D E FG H IJLM N O * + 1 Spare(see Fig.1).2. With the door closed and latched fix the template to the door and frame. Place the edge of the template 60mm (2.4") from the side frame (see Fig.4).3. Mark the centre of each hole shown on the template and drill holes to size and depth stated on Template.4. From the outside of the door enlarge the 9mm hole to 12mm to a depth of 36mm (On Hollow doors enlarge the hole to 16mm through the outer door skin only to accomodate the a hollow door push the the Aluminium spacer (C) into the 16mm hole then cut down flush with door face. Push Dome nut (B) into Spacer (C).6. Gently tap the 2 guide pins (H) into the holes on the back of the Armature plate. Push the M8 50mm Allen bolt (A) through the countersunk hole in the Armature plate. Slide a Steel washer (F) over the M8 Allen bolt at the back of the Armature plate followed by a Rubber washer (G) and a Steel washer (F). (see Fig.5).7. Fix the Armature plate to the door using the Allen key (L) and tighten until the Armature plate sits 3-5mm away from 8. Using the Allen key wrench (L) remove the two M6 Allen bolts (N) and metal spacer (O) through the holes at the base of the magnetic lock. Slide the Mounting plate forward and lift up to remove it from the lock (see Fig.6).10mm cable hole is visible through the oval hole of the plate.Fix using two No 8 15mm Csk screws (E) through the slotted holes into pilot holes drilled previously (see Fig.7).Oplate towards the Armature plate until the edges are 2-3mm apart and parallel along the length of the armature plate (see Fig.8).O14. Hold the Magnet with the front facing the armature plate and the mushroom head screws at the top. Lift the magnet up onto the Mounting plate with the mushroom head screws located into the 13mm slotted holes and push forward towards the Armature plate. (see Fig.10).15. Fix the magnet to the mounting plate using two M6 Allen bolts (N) and Metal Spacer (O) fixed through the holes in the bottom of the magnet and tighten with the Allen key wrench (L).frame (see Fig.11) and connect to Magnet PCB as per wiring instructions on pages 7&8.17. Apply voltage to the Magnet. Close the door andcheck Armature plate is correctly aligned with the magnet. Apply firm pressure against the door to check magnet is holding properly. Remove voltage and open the door.apply Thread lock. Re-fit as per steps 6&7.19. Remove one at a time the M6 Allen bolt (N) from the bottom of the magnet and apply Thread lock. Re-fit as per step 15.20. Using the two M4 25mm Csk screw (J) fix the PCB cover plate in position on the magnet and into the counter sunk hole at the opposite end (see Fig.12). These screws will prevent the M6 Allen bolt from unscrewing (see Fig.12A).11. Mark the centres of the 6 countersunk holes through the Mounting plate.12. Drill six 3.2mm dia. holes to a depth of 25mm for the No 10. 32mm Csk screws.13. Fix the Mounting plate with the 6 No. 10 32mm Csk screws (D). (see Fig.9).ALLEN BOLTS FROM UNSCREWINGFIG 17Head Frame. (see Fig.2).2. With the door closed and latched, tape the template to the door and frame. Place the edge of the template 60mm from the side frame. (see Fig.13).3. Mark vertical lines for the 'L' bracket at the edge of the template, mark centre of each hole shown on the template. Drill all holes to the size and depth shown on template.4. From the outside of the door enlarge the 9mm hole to 12mm to a depth of 36mm (on a hollow metal door drill a 16mm hole through the outer door skin only to accommodate a hollow door push the the Aluminium spacer (C) into the 16mm hole then cut down flush with door face. Push Dome nut (B) into Spacer (C).6. Gently tap the 2 guide pins (H) into the holes on the back of the Armature plate. Push the M8 50mm Allen bolt (A)through the counter sunk hole in the Armature plate followed by one Rubber washer (G) sandwiched between 2 Steel washers (F) behind the Armature plate. (see Fig.14).7. Fix the Armature plate to the door using the Allen key (L) and tighten until the Armature plate sits 3-5mm away from the 8. Using the Allen key wrench (L) remove the two M6 Allen bolt (N) and Metal spacer (O) through the bottom of the magnetic lock. Slide the Mounting plate forward and lift up to remove it from the magnet. (see Fig.15).9. Remove the two Mushroom head screws from the top of the magnet and replace with the two M5 8mm machine screw (I).10. Use the Transom 'L' bracket (AC-EMBR006) as atemplate. Place the short side between the vertical lines on the frame (make sure it is flat against the frame) the bottom of the bracket should be 5mm below the underside of the frame header (fig 16).12. With the door closed and latched place the face of the magnet so that it touches the Armature plate and check that the hole in the top of the magnet lines up with one of the tapped holes on the bracket. If the holes do not line uploosen the M8 Allen bolt (A) making sure the gap behind the14. Pass lock cable through the cable entry hole (see Fig.19) and connect to Magnet PCB as per the wiring instructions on pages 7&8.15. Apply voltage to the Magnet. Close the door and check Armature plate is correctly aligned with the magnet. Apply firm pressure against the door to check magnet is holding properly. Remove voltage and open the door.16. Remove M8 Allen bolt (A) from Armature plate and apply Thread lock. Re-fit as per step 6&7.17. Remove one at a time the M6 Allen bolt (N) from the bottom of the magnet and apply Thread lock. Re-fit as per step 13.18. Using the two M4 25mm Csk screw (J) fix the PCB Cover plate in postion on the magnet and into the counter sunk hole at the opposite end (see Fig.20). These screws will prevent the M6 Allen bolt from unscrewing (see Fig.20A).13. Fix the magnet to the bracket using two M6 Allen bolts (N) and Metal spacer (O) fixed through the holes in thebottom of the magnet and tighten with the Allen key wrench (L). (see Fig.18).OALLEN BOLTS FROM UNSCREWINGFixing detail - Standard Double Magnetic Lock - Models 10040 and 10060REV 1.0Installation to Deep Header frame using Flat Mounting PlateInstallation to Shallow Header frame using 2 Transom 'L' BracketsThe Standard Double magnetic locks are used for a pair of double doors. They are fixed in exactly the same way as the Single version using 2 fixing packs.1. With both doors closed and latched fix the template across the centre of both doors and continue as steps 3&4 on page 2 (see Fig. 21).2. Fit the 2 Armature plates to each door as per steps 5-7 (Fig.5) on page 2.3. Remove the four M6 allen bolts (N) and Metal spacers (O) as per step 8 page 2 (see Fig.22).4. Fix the Mounting plate using 4 No.8 15mm Csk screws (E) as per step 9 page 2. Ensure Mounting plate is adjusted correctly as per step 10 (Fig.8) page 2.5. Fix the mounting plate using 12 No. 10 32mm Csk screws (D) as per steps 11-13 (Fig.9) page 3.6. Fix the Magnet to the mounting plate using four M6 Allen bolts (N) & Metal Spacers (O) as per steps 14&15 page 3.7. Fit 2 seperate cables for each magnet PCB as per steps 16&17 (Fig.11) page 3.8. Apply Thread lock to Allen Bolts as per steps 18&19 page 3.9. Fit four M4 25mm Csk screws (J) as per step 20 (Fig.12) page 3.1. With both doors closed and latched fix the template across the centre of both doors and continue as steps 3&4 on page 4 (see Fig. 23).2. Fit the 2 Armature plates to each door as per steps 5-7 (Fig.5) on page 4.3. Remove the four M6 allen bolts (N) and Metal spacers (O) as per step 8&9 page 4 (see Fig.22).4. Place the two 'L' brackets together and continue as per steps 10&11 page 4 (see Fig.24).5. Close both doors and line up Magnet with brackets as per step 12 (Fig.17) page 4.6. Fix the Magnet to the 2 'L' brackets using four M6 Allen bolts (N) & Metal Spacers (O) as per step 13 (Fig.18) page 5.7. Fit 2 seperate cables for each magnet PCB as per steps 14&15 (Fig.19) page 5.8. Apply Thread lock to Allen Bolts as per steps 16&17 page 5.9. Fit four M4 25mm Csk screws (J) as per step 18 (Fig.20) page 5.The standard magnet is designed to be operated by 12 or 24 volt DC systems. The Printed Circuit Board (PCB) in the magnet is factory set for 12V operation but can easily be changed for 24V operation (see wiring detail). The PCB also has built - in protection against Back EMF surges which means a seperate Diode or MOV is not needed. Because the magnet is Fail Unlock (Fail Safe) it needs a constant DC supply to hold the Armature plate in position, it is therefore recommended that a Rechargable Battery is fitted in the Power supply.Important Points to consider before Installation:-1. The Magnet must be connected to a Regulated DC Power supply (Ideally with BatteryBackup facility).2. Input voltage at the magnet PCB must be 12 or 24V `10%3. The PCB already has built-in protection against Back EMF surges.4. The Maximum current draw for 12V is 500mA and for 24V 250mA (Double version willdraw twice as much).5. DO NOT reverse polarity as this will result in damage to the PCB and Coil.6. There are two versions of the PCB - Unmonitored (Models 10010 and 10060) andMonitored (Models 10020 and 10040).7. Ensure all cabling and wiring connections conform to current Electrical Legislation.1. Check magnet PCB is set for correct voltage (Factory setting is 12V).2. Connect Negative Output (-) from Power Supply to terminal 2 (-) on Magnet PCB.3. Connect Positive Output (+) from Power Supply to Common of Relay or Exit switch.4. Connect Normally Closed (N/C) on Relay or Exit switch to terminal 1 (+) on Magnet PCB.5. With the door open switch Power supply On and check that the Magnet will hold a Screwdriver.6. Operate the Access Control Relay or Exit switch whilst holding the screwdriver to check magnet is working.7. If the Screwdriver is released close the door and check the Holding force by pulling / pushing the door.8. Re-fit the PCB cover plate with M4 25mm Csk Screw (J).RELAY OR EXIT SWITCH1. Check Magnet PCB is set for correct voltage (Factory setting is 12V).2. Connect Negative Output (-) from Power Supply to terminal 2 (-) on Magnet PCB.3. Connect Positive Output (+) from Power Supply to Common of Relay or Exit switch.4. Connect Normally Closed (N/C) on Relay or Exit switch to terminal 1 (+) on Magnet PCB.5. Connect Positive Output (+) from Power Supply to terminal 4 (Common) on Magnet PCB.6. Connect Negative Output (-) from Power Supply to Negative (-) terminal on each Lamp.7. Connect terminal 3 (NO) to Positive (+) terminal of Lamp (DOOR LOCKED).8. Connect terminal 5 (NC) to Positive (+) terminal of Lamp (DOOR OPEN).9. With the door open switch Power supply On and check that the Magnet will hold a screwdriver.10. Operate the Access Control Relay or Exit switch whilst holding the screwdriver to check magnet is working.11. If the Screwdriver is released close the door and check the Holding force by pulling / pushing the door.12. Check that the 2 Lamps are working correctly when the Magnet locks and unlocks.13. Re-fit the PCB cover plate with M4 25mm Csk Screw (J).。
磁力锁使用说明
按“CLOCK”键，设定年、月、日、时、分
输入主密码“12345678”按“MENU”键，查询开箱记录
在“9-1”计数期间按按“1”键，开箱记录数据传送到打印机
不按任何键，计数完毕后，箱门自动打开，并显示客密码。
1.按“CLR”键，修改主密码
输入任意8位密码，显示“Good”表示修改成功。
在输入过程中按“CLR”键，表示清除。
三、工作条件
电 源：四节5号“AA”碱性电池 功 耗：<10uA
工作温度：-10℃-+70℃ 工作湿度：10%-90%RH
密码容量：≥104
开箱记录：14条(120条)
四、维护、保养及注意事项
用户遗忘主密码处理：先按住红色设置键不放。再按任意功能键，叫“嘟--------”一长声，遗忘主、客密码清除。这时密码恢复出厂密码：主密码为“12345678”，客密码为“8888”。
按“MENU”显示“★★★★”表示客密码
按“MENU”显示“★★★★”表示年
按“MENU”显示“★★★★”前二位表示月份，后二位表示日期
按“MENU”显示“★★★★”前二位表示小时，后二位表示分钟
4.按“1”键，开箱记录数据传送到打印机
把打印机和智能锁用通信电缆连接，输入主密码“12345678”在“9-1”计数期间。按“1”键，显示“PRINT”。再按打印机开始键，把开箱记录数据打印出来。
在输入密码或开关箱过程中出现“LOBATT”字样，表示电池电量不足，须更换电池。
同时箱门自动锁定。
2.客密码开箱:
输入预先自行设置的任意4位密码即可开箱。
例：按数字“1111”同时箱门自动打开
若输入错误密码，按“CLR”键清除误码，重新输入密码。
AZM300系列电磁锁说明书
AZM300More than just a solenoid interlockAZM300Protection against hazardous inertial movementsOne of the unique features of the AZM300 is the innovative patented operating principle with rotating shaft and star handle.This operating principle offers the advantage that the safety guard is pulled into its end position upon closing the guarddoor and it is held shut. The solenoid interlock can be used as an end stop, which eliminates the use of a separate doorstop. The integrated latching ensures that the closed condition of the door is maintained after the unlocking of the solenoidinterlock and that the door cannot autonomously open itself. The latching force can be easily increased by turning the starhandle by 180° from 25 N to 50 N.For safe identification of the actuator an RFID sensor is used, featuring three different coding levels thus providing protectionagainst defeat.Fields of application■ Wood-processing machinery■ Printing machines and presses■ Handling and assembly technology■ S pecial-purpose and customisedmachine construction■ Food-processing industry■ Pharmaceutical industryPrinting machines and pressesProtecting humans and machinesThe safety outputs of the AZM300Z solenoid interlock (solenoid interlock monitoring) are enabled when the safety guard is closed and the solenoid interlock is locked.For applications where process protection is required, the AZM300B version (actuator monitoring) can be used. The safety outputs of this model are enabled when the safety guard is closed and can be locked. With this device locking is not required for operation, however the ability for a proper locking is still monitored.Identical mounting for left and right hinged doorsThree actuating directionsActuation from the slim side Actuation from frontAcutation from the rearsideProtection against defeating through individual codingIf interlocking devices are defeated, the machine is not operated under the conditions foreseen by the manufacturer. The result could be a significantly increased residual risk for the operator, possibly much higher than acceptable.If the defeating incentive cannot be eliminated completely by modified or additional modes of operation, then the designer has only one element left. This is to make the defeating of interlocking devices more difficult or even impossible. (Excerpt from prEN ISO 14119).The basic version of the AZM300 accepts any suitable target. A second version only accepts the actuator that has been taught upon the first activation. And finally, a third variant is available; here, the teaching process can be repeated anarbitrary number of times. In this way, the user can choose the most suitable coding variant for the intended application as well as the desired degree of protection against defeating. This is enabled by integration of the RFID technology into the safety sensor technology.Teaching actuators without additonal toolsThe AZM300-I1 and AZM300-I2 versions with individual coding, no tool whatsoever is required for the actuator teaching procedure.The teaching process starts automatically as soon as the device is switched on. The user must connect the solenoid interlock to the operating voltage and bring the actuator into the detection range. After approx. 10 seconds, a brief cyclic flashof the AZM300 LED indicates to remove the operating voltage. Next the operating voltage is switched back on and the actuator must be placed in the detection range once again to activate the actuator code.For ordering suffix -I1, once the actuator coding process has been completed it is irreversible. For ordering suffix -I2, the teaching procedure for a new actuator can be repeated an unlimited number of times. A restart inhibit period of 10 minutes prevents thelast-minute change of an actuator, thus increasing the protection against tampering.Automatic teaching after the operatingvoltage is switched on10 minute restart inhibit following the teaching procedure of a replacement actuatorMinutesSerial diagnosticSimilar to all electronic safety sensors and solenoid interlocks from Schmersal, the AZM300 is also available with serial di-agnostic. Solenoid interlocks with serial diagnostic feature have a serial input and output cable instead of the conventionaldiagnostic output. When solenoid interlocks are wired in series, the serial diagnostic cables are wired in series, in additionto the safety channels. The thus created "common diagnostic line" is wired to a serial Diagnosic Gateway for evaluation.Up to 31 different Schmersal electronic safety devices can be wired in series.For the evaluation of the serial diagnostics line either the PROFIBUS-Gateway SD-I-DP-V0-2 or the Universal-GatewaySD-I-U-… are used. This serial diagnostic interface is integrated as a slave in an existing field bus system. In this way,the diagnostic signals can be evaluated by means of a PLC. In addition to the comprehensive diagnostic and status infor-mation, the solenoid interlock is locked or unlocked through the diagnostic cable. The device can be wired either directlyto the machine through a special Y-adapter or in the control cabinet by means of terminal blocks. Because of the use ofserial diagnostics, an input (diagnostic) and an output (locking signal) can be saved for each device in the PLC.Hygiene-sensitive applications Packaging machineryFeaturesEasy latching force adjustment ■ T he latching force can be increased from 25 N to 50 N simply by turning the star handle 180°.■ P osition I: approx. 25 N, Position II: approx. 50 N LED display ■ S mart diagnostic by means of 3-color LEDs ■ L ED green: Power LED yellow: Status LED red: FaultLarge actuator tolerances ■ A ctuator tolerance inlongitudinal direction ± 3.5 mm, lateral direction ± 2.0 mmLegend➀H igh degree of protection against tampering because of the coded RFID sensor (also available with individual coding)➁ Dampener for door stop - saves costs: no additional mounting parts required ➂ Star handle - adjustable latching force - 25 N or 50 N ➃ Mounting hole for M6 screws ➄ Connector plug M12, 8-pole ➅ Manual release ➆ LED display± 3.5 mm± 2.0 m mThe AZM300 in detail➃➅➆➄Technical dataElectronic safety sensorsAZM300 ➀ - ➁ -ST- ➂ - ➃No. Option Description➀Z Guard locking monitored B Actuator (RFID) monitored➁Standard versionI1 Individual coding (Irreversible) I2 Individual coding (re-teachable)➂ 1P2P Diagnostic outputSD2P Serial Diagnostic ➃Power to unlock (spring lock)APower to lock• Thermoplastic enclosure • 2 short-circuit proof, p-type safety outputs (24 VDC per 250 mA)• I ncreased protection against tampering by optional individual coding of safety sensor and actuator• Adjustable latching from 25N to 50N • S afety and diagnostic signals can be wired in series • I ntegral cross-wire, wire breakage and external voltage monitoring of the safety cables up to the control cabinet • LED status indication • R obust design using cleaningagent-resistant materials achieving protection class IP69K ApprovalsOrdering detailsActuator AZ/AZM300-B1• Thermoplastic• Solenoid actuator key • Dampener for end stop • RFID tagApprovalsCertification incombination withsafety sensorOrdering detailsConnector CablesA-K8P-M12-S-G-5M-BK-1-X-A-4 IP69K cable, 5 meter length A-K8P-M12-S-G-10M-BK-1-X-A-4 IP69K cable, 10 meter length A-K8P-M12-S-G-5M-BK-1-X-A-2 IP67 cable, 5 meter length A-K8P-M12-S-G-10M-BK-1-X-A-2 IP67 cable, 10 meter length MountingMP-AZ/AZM300-1 Spacer plateMS-AZ/AZM300-B1 Mounting kit for actuatorStandards: IEC 60947-5-3, IEC 60947-5-1, IEC61508, EN ISO 13849-1Enclosure: glass-fibre reinforced thermoplasticMode of operation:RFID Actuator: AZ/AZM300-B1Series-wiring: unlimited number of components, up to 200 M; max. 31components for serial diagnosisConnection: Integrated connector M12 - Integrated connector: M12, 8-pole, A-coded Switching distances to IEC 60947-5-3:Rates switching distance S n : 2 mm Assured switch-on point S ao : 1 mm Assured switch-off point S ar : 20 mm Minimum distance between two sensors: 100 mm Ambient conditions:Ambient temperature Tu: 0 °C … +60 °C Storage and transport temperature: -10 °C … +90 °C Protection class: IP66 / IP67 to EN 60529; IP69K to DIN 40050-9 Mechanical Data:Resistance to vibration: 10…150 Hz,amplitude 0.35 mmResistance to shock: 30 g / 11 ms Electrical data:Switching frequency f: 0.5 Hz Response time: 120 ms Duration of risk: < 200 ms Standby delay: ≤ 5 s Rated Supply voltage U s : 24 VDC -15% / +10%(PELV)Power consumption with solenoid enabled: 0.25 APower consumption without load: 0.1 A Required rated short-circuit current:100 AOrdering detailsNOTESAZM Rev1 7/13660White Plains RoadSuite 160Tarrytown,New York 10591Tel:(914)347-4775Fax:(914)347-1567E-mail:********************** USA 15Regan Road Unit #3Brampton,Ontario L7A 1E3Tel:(905)495-7540Fax:(905)495-7543E-mail:************************* CanadaElectronic Safety Sensor & Solenoid Interlock Product FamilySchmersal offers a wide selection of Electronic safety devices which are designed to help solve application challenges for industry while enhancing operator safety.■ N on-contact sensor principle■ 3 color LEDs indicate status, error codes ■ Integrated dual monitoring microprocessor provides continuous internal function tests ■ Highest level of safety: PLe per ISO 13849-1, SIL3 per IEC 62061■ Wired in series without detriment to safety level ■ Serial Diagnostic option for connection to PLCs ■ RFID allows for individual coding of actuators The available features from the Schmersal electronic family provide our customers multiple options when selecting the appropriate productfor any application.CSS180CSS34CSS30SAZ200/AZM200RSS36AZM300CSS16MZM100。
JDY-280磁力门锁安装说明
JDY-280磁力门锁安装说明请参考图1的出线分配JDY-280磁力锁需要外接一组12伏或24伏直流电供其正常运作。
注意：必须在PC板上选择外接12伏或24伏直流电步骤完成后，才可供应正确的电源。
JDY-280内含磁簧开关用来推动继电器及LED的灯号，经由干接点输出的变化及LED的显示不同可为门开或门关的判断。
选择外接12伏直流电时：1、如图示，将拨动开关1、2拨至ON位置，3拨至OFF位置。
2、将12伏直流电的正极接上PC板上端子台标示“+”的位置。
3、将12伏直流电的负极接上PC板上端子台标示“-”的位置。
选择外接24伏直流电时：1、如图示，将拨动开关3拨至ON位置，1、2拨至OFF位置。
2、将24伏直流电的正极接上PC板上端子台标示“+”的位置。
3、将24伏直流电的负极接上PC板上端子台标示“-”的位置。
耗电量：12伏直流电-0.530安培24伏直流电-0.265安培干接点的输出及LED的显示：电源供应及门闭时：干接点C及NO导通，LED显示绿色。
电源供应及门开时：干接点C及NC导通，LED显示红色。
无电源供应时：干接点C及NC导通，LED灭。
注：干接点最大可承受24伏直流电-1安培的电流量。
注意事项安装时，不要将铁板紧锁在门上，应让其左右能上下稍微摆动为原则。
如此可让继铁板和磁铁块能以最自然的方式结合。
不要修剪或拿掉在继铁板中心螺丝上的橡胶圈。
否则，磁力门锁在操作时会达不到预期的效果。
问题的发生及处理接线时，请用最适合的线径并锁紧在端子台内。
问题的发生可能的原因解决方法门无法关闭无电源供应检查电源供应器输入端子台上的电源将电源线锁紧在端子台上线松掉拉力减少电压不足调整电压门变形或磁力门锁安调整门或重新安装装不良，导致继铁板磁力门锁和磁铁块接触面缩小继铁板或磁铁块表面清除杂质有杂质门开启时有在电源输入的正负上取出二极体延迟的现象加装了二极体LED灯号错误继铁板和磁铁块没有将继铁板和磁铁块完全接触面重新定位磁簧开关在磁铁块内重新安置磁簧开关的位置错误至正确的位置，请联络供应商保养继铁板和磁铁快表面必须无杂质，请定期用非蚀性的清洁剂清理表面。
LK-M012L MAGLOCK 1200 LBS 磁力锁说明书
LK-M012LMAGLOCK 1200 LBS with Lock Status and IndicatorJune 2012Installation Manual11. IntroductionThe LKM12L is a surface mounted magnetic lock series with 1200 lbs holding force. LKM12L has dual voltage (12 or 24 VDC) and lowcurrent consumption with anodized aluminum housing. LKM12L has a built-in voltage spike suppressor and no residual magnetism. Monitored status output and timer versions are available. Different types of bracket and housing are available to fit various mounting conditions.LKM12L is compatible with EN55011:1998: Class B, EN60601-1-2:2002, EN61000-4-2:1995, EN61000-4-3:2002 & UL-S5351.Figure 1: LKM012L2. Technical Specifications2.1Electrical Characteristics2.2 Physical Characteristics3. MountingBefore attempting to install magnetic lock: ▪ Handle the equipment with care. Damaging the mating surfaces of the magnet or armature plate may reduce locking efficiency. ▪The magnet mounts rigidly to the door frame. The armature plate mounts to the door with hardware. Kit provided that allows it to pivot about its center to compensate for door wear and misalignment.▪ Template use must take place with the door in its normally closed position.▪Before installing, please add the thread locker to all screws. Firmly tighten the screws to avoid fastening loosen.Typical mountings are shown in Figure 2.Figure 2: Surface MountingWhen fixing the armature plate: ▪ Do not fix the plate too tightly▪Make the rubber washer more flexible to make the armature plate automatically adjust its proper position with the magnetFigure 3 shows how to mount an armature plate/surface.Figure 3: Armature Plate/Surface Mounting4. W iring4.1I nputFor a 12 VDC input, a maximum of 0.5 A power is needed. For a 24 VDC input, a maximum of 0.25 A power is needed. The unit should only be powered by a UL listed power supply. If the power switch is not wired between the DC source voltage and magnet, it will take a longer time to de-energize the magnet simulating residual magnetism (see Figure 8).Figure 4: WiringTo wire input:1.Connect the ground (-) lead from the power source to Terminal 2. 2.Connect the positive (+) lead from the power source to Terminal 1.3.Set the jumper for either 12 or 24 VDC operation.4.2C ontactsThe relay dry contacts are rated 1 amp at 24 VDC for safe operation – do not exceed this ratingIf you require a normally open switch, connect the wires from the system to terminal 4 and terminal 3.If you require a normally closed switch, connect the wires from the system to terminal 4 and terminal 5.Figure 7 shows various PCB schematics with the jumper settings.Figure 5: PCB SchematicLimited WarrantyROSSLA RE ENTERPRISES LIMITED (ROSSLARE) ONE-YEAR LIMITED WA RRA NTY is applicable worldwide. This warranty supersedes any other warranty. ROSSLARE'S ONE-YEAR LIMITED WARRANTY is subject to the following conditions:W ARRANTYWarranty of ROSSLARE'S products extends to the original purchaser (Customer) of the ROSSLARE product and is not transferable.P RODUCTS C OVERED B Y T HIS W ARRANTY AND D URATIONROSSLA RE ENTERPRISES LTD. AND/OR SUBSIDIA RIES (ROSSLA RE) warrants that the LK-M12L Maglock to be free from defects in materials and assembly in the course of normal use and service. The warranty period commences with the date of shipment to the original purchaser and extends for a period of 1 year (12 months).W ARRANTY R EMEDY C OVERAGEIn the event of a breach of warranty, ROSSLARE will credit Customer with the price of the Product paid by Customer, provided that the warranty claim is delivered to ROSSLARE by the Customer during the warranty period in accordance with the terms of this warranty. Unless otherwise requested by a ROSSLARE representative, return of the failed product(s) is not immediately required.If ROSSLA RE has not contacted the Customer within a sixty (60) day holding period following the delivery of the warranty claim, Customer will not be required to return the failed product(s). A ll returned Product(s), as may be requested at ROSSLA RE’S sole discretion, shall become the property of ROSSLARE.To exercise the warranty, the user must contact ROSSLARE Enterprises Ltd. to obtain an RMA number after which, the product must be returned to the Manufacturer freight prepaid and insured.In the event ROSSLARE chooses to perform a product evaluation within the sixty (60) day holding period and no defect is found, a minimum US$ 50.00 or equivalent charge will be applied to each Product for labor required in the evaluation.ROSSLARE will repair or replace, at its discretion, any product that under normal conditions of use and service proves to be defective in material or workmanship. No charge will be applied for labor or parts with respect to defects covered by this warranty, provided that the work is done by ROSSLARE or a ROSSLARE authorized service center. E XCLUSIONS AND L IMITATIONSROSSLA RE shall not be responsible or liable for any damage or loss resulting from the operation or performance of any Product or any systems in which a Product is incorporated. This warranty shall not extend to any ancillary equipment not furnished by ROSSLARE, which is attached to or used in conjunction with a Product, nor to any Product that is used with any ancillary equipment, which is not furnished by ROSSLARE.This warranty does not cover expenses incurred in the transportation, freight cost to the repair center, removal or reinstallation of the product, whether or not proven defective.Specifically excluded from this warranty are any failures resulting from Customer's improper testing, operation, installation, or damage resulting from use of the Product in other than its normal and customary manner, or any maintenance, modification, alteration, or adjustment or any type of abuse, neglect, accident, misuse, improper operation, normal wear, defects or damage due to lightning or other electrical discharge. This warranty does not cover repair or replacement where normal use has exhausted the life of a part or instrument, or any modification or abuse of, or tampering with, the Product if Product disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection and testing to verify any warranty claim.ROSSLARE does not warrant the installation, maintenance, or service of the Product. Service life of the product is dependent upon the care it receives and the conditions under which it has to operate.In no event shall ROSSLARE be liable for incidental or consequential damages.L IMITED W ARRANTY T ERMSTHIS WARRANTY SETS FORTH THE FULL EXTENT OF ROSSLARE’S WARRANTY.THE TERMS OF THIS WARRANTY MAY NOT BE VARIED BY ANY PERSON, WHETHER OR NOT PURPORTING TO REPRESENT OR ACT ON BEHALF OF ROSSLARE.THIS LIMITED WA RRA NTY IS PROVIDED IN LIEU OF A LL OTHER WA RRA NTIES.A LL OTHER WA RRA NTIES EXPRESSED OR IMPLIED,INCLUDING WITHOUT LIMITATION, IMPLIED WA RRA NTIES OF MERCHA NTA BILITY A ND FITNESS FOR A PA RTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED.IN NO EVENT SHA LL ROSSLARE BE LIA BLE FOR DA MA GES IN EXCESS OF THE PURCH A SE PRICE OF THE PRODUCT,OR FOR A NY OTHER INCIDENT A L, CONSEQUENTIAL OR SPECIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF USE,LOSS OF TIME,COMMERCIA L LOSS,INCONVENIENCE,A ND LOSS OF PROFITS, ARISING OUT OF THE INSTALLATION, USE, OR INABILITY TO USE SUCH PRODUCT, TO THE FULLEST EXTENT THAT A NY SUCH LOSS OR DA MA GE MA Y BE DISCLA IMED BY LAW.THIS WARRANTY SHALL BECOME NULL AND VOID IN THE EVENT OF A VIOLATION OF THE PROVISIONS OF THIS LIMITED WARRANTY.Contact InformationAsia Pacific, Middle East, Africa Rosslare Enterprises Ltd.Kowloon Bay, Hong KongTel: +852 2795-5630Fax: +852 2795-1508********************************* United States and Canada Rosslare Security Products, Inc. Southlake, TX, USA 76092Toll Free: +1-866-632-1101Local: +1-817-305-0006Fax: +1-817-305-0069*******************************EuropeRosslare Israel Ltd.Rosh HaAyin, Israel 48091Tel: +972 3 938-6838Fax: +972 3 938-6830*******************************Latin AmericaRosslare Latin AmericaBuenos Aires, Argentina 1642*******************************ChinaRosslare Electronics (Shenzhen) Ltd.Shenzhen, ChinaTel: +86 755 8610 6842Fax: +86 755 8610 6101******************************* 76-96448+2。
安全门磁锁说明书
FeaturesStandard Features• Fire rated—3 hours• PoE friendly• Sustainability documentation • Efficient, low power usage• Automatic dual-voltage—no field adjustment required • Fully sealed forweather resistant operations • Size optimized for usewith door closers• Rust resistant—all ferrous metal surfaces plated for durability • Instant release circuit—no residual magnetism• Noise suppression withbuilt-in MOV• 10 ft [3.05m] of jacketed,stranded conductor cable• Ultra-secure collapsing blind nuts mount to door framefor strength and reliability• MagnaCare® lifetime replacement, no-fault, no questions asked warranty Optional Features• F Face drilled• G Gate conduit• B Patented BondSTATmagnetic bond sensor• D Integrated DoorPosition Switch (DPS)• SS Split Strike• SASM Shock AbsorbingStrike Mount for Gates• OS Offset Strike• EX UL Certifiedfor Hazardous LocationsNOTE: Only available with "G"configurations (e.g. M62G-EX)The ultimate inMagnalock versatilityfor indoor/outdoorhigher security.The M62 is a strong, easy-to-maintainsolution for interior, perimeter and exterioraccess control. With unsurpassed durability,the M62 will last long after most buildingswear out. Flexible mounting options supportapplications for hollow metal, concretefilled metal, wood, or glass with aluminumframes, and all glass doors. Options includesingle and double door configurations,or specialty applications such as gatesand fences, and hazardous locations.NOTE: M62FG-SASM in SpecialtyLock section. See page #62.®DimensionsSpecificationsCertifications• UL 10C Listed• CAN4-S104, CAN/ULC-S533 Listed • ANSI/UL 294 Listed • CSA-C22.2 No.205 Listed • ANSI/BHMA A156.23, Grade 2; E08501-1000 Compliant• CSFM—California State Fire Marshal Approved • CE:EN 50081-1(92), EN 61000-6-2(99) Approved • Environmental Product Declaration • Health Product Declaration•UL 294 Class I, Division 2, Groups A, B, C and D Listed (-EX configuration only)Electrical• 250 mA at 12 VDC • 150 mA at 24 VDCHolding Force• 1,200 lbs [544kg]Operating Temperature• -40˚ to 140˚F [-40˚ to 60˚C]• Indoor or Outdoor useShipping Weight• 11 lbs [5kg]**Only applicable to configurations including the Gate Conduit (G ). Please contact the factory with any questions.M62 Magnalock3"ASB Aluminum Spacer Bracket• Use when a blade stop requires the Magnalock to be lowered • Comes pre-drilled for the mounting bolts and wire • Provides a blind nut for surface installation of strike • Available in clear aluminum or black anodized•MagnaCare ® lifetime replacement, no-fault, no questions asked warrantyCWB Concrete Wood Bracket• Used on wood or concrete filled metal frames • Provides a concealed wire chamber• Available in clear aluminum or black anodized•MagnaCare ®lifetime replacement, no-fault, no questions asked warrantyASS Split Strike/Replacement Strike Plate• Allows a single M32, M62 or M82 Magnalock to secure adouble door at traffic control holding force level.• Includes Split Strike Plates only.• MagnaCare ® lifetime replacement, no-fault, no questions asked warranty.ZA Z Bracket Kits – Adjustable• Use on in-swing doors with Magnalock "F" options (8-1/2" [215.9mm] overall length).• Provides 1-1/4" [31.75mm] of lateral movement toaccommodate most openings and allows for precision adjustments (2-1/4" to 3-1/2" [57.15mm to 88.9mm] from door/header).• Includes an oversized dress cover.• MagnaCare ® lifetime replacement, no-fault, no questions asked warranty.M32/62/82 MagnalockAccessoriesAOS Offset Strike Plate• Alters the position of the mounting hole by 1/4" [6mm]. This is oftenrequired to clear the glass on aluminum frame store front doors.• Includes Offset Strike Plate only.• MagnaCare ®lifetime replacement, no-fault, no questions asked warranty.TDK-1 Accessory for Thick Doors• Provides replacement screws so armature plates for the M32, M62, M82, M38 and M68 can be used on doors thicker than 1-3/4" [44.45mm], and up to 3" [76.2mm].• MagnaCare® lifetime replacement, no-fault, no questions asked warranty.SB-1 Sex Bolt Replacement• Replaces armature plate sex bolt for M32, M38, M62, M68 and M82B Magnalocks.• Available in clear, polished brass or oil rubbed bronze finish.• MagnaCare® lifetime replacement, no-fault, no questions asked warranty.M32/62/82 MagnalockAccessoriesDDC Double Dress Covers•Use with M32/M62.•Available in clear anodized and black finish.•Will cover a pair of Magnalocks on a double door(if they are separated by no more than 2").•Not for use with the DM62 Magnalock.•MagnaCare ® lifetime replacement, no-fault, no questions asked warranty.MTK Metal Marking Template•Magnetic template streamlines installation for the M32 and M62 Magnalocks. •Includes basic instructions and hole placements.DC Dress Covers•Use with M32, M62, and M82.•Install using foam adhesive tape.•Available in clear, black, polished stainless and polished brass finish.•MagnaCare ®lifetime replacement, no-fault, no questions asked warranty.How to OrderSpecify quantity and the following information. Order related products separately.NOTE: Configurable parts HHSL-82 and HHSR-82 have beendiscontinued. Not every combination is possible. Please contact the factory if you need a combination of features not listed above.M32/62/82 Magnalock AccessoriesHHD / HHSL / HHSR / HVD Full Length Housings• Vertical or horizontal configurations • Fit one or two locks (not included)• (SLR) Single Left Hand Reverse • (SRR) Single Right Hand Reverse•MagnaCare ®lifetime replacement, no-fault, no questions asked warranty*Full length housings are individually manufactured to custom specifications up to the maximum length shown.CAHHD Horizontal Housing Dimensions。
880磅电磁锁，无线控制，型号：MAGLOC880说明书
880 LB ELECTROMAGNETIC LOCK3.More featuresDirect or wireless transmitter memorisation Full memory erasure Single transmitter cancelling C-NO or C-NC output contact (selectable )Direct magnet unlock with C-NO push-button 1. Introduction . k c o l g a m r o o d k c o l g a m d e l l o r t n o c o i d a r e h T The maglock release command can be sent or by radio, with a 2 key transmitter type 433TSPW2V or a 4 key transmitter type 433TSPW4V ( fig.1), or using an external C-NO push-button ( not provided ). The magnet unlock starts at the release of the button and lasts the programmed time ( par. 8) : default unlock time = 4 sec. NOTE : a short applied at the C-NO inputs can keep the magnet always unlocked.The maglock is equipped with a monitor output R-R ( C-NO or C-NC selectable with a jumper), see image below.MAGLOC880is a 880 lb (400Kg) radiocontrolledOperating temperature.........................................24°F 158°F÷5.Transmitter memorisation5.1Memorising with P1push-button (Fig.3)1) Push P1 for 4 sec. until L1+L2 turns OFF 2) Push the transmitter button to memorise, L1+L2 will flash and come back OFF , the magnet will have a pulse of UNLOCK. While L1+L2 are OFF it’s possible to memorize more TX buttons.After 5 sec. from the last memorisation L1+L2 turn back ON , the procedure ends and the magnet LOCKS AGAIN.7 . Memory erasure 7.1 Single transmitter cancelling (Fig. 4)The procedure to cancel the single transmitter is the identical to the memorisation and carried out only by using P1.Follow the steps 1 and 2 of the procedure at paragraph 5.1If the transmitter was memorised, at the end it will be cancelled.7.2 Full memory erasure ( Fig. 5)1) Push P1 and keep it pushed until L1+L2 turn OFF;2) Release P1 and then, before L1+L2 turn on again, keep pushed P1 until L1+L2 make 3 long flashes At that point the memory has been completely erased.5.2Wireless memorising (without accessing P1)(Fig.4)1)Push simultaneously the buttons A +B of the transmitter and the led L1+L2will make a SHORT FLASH.2)Release A+B and push the A until the led L1+L2TURN OFF 3)Release A and push the of the transmitter to memorise (A or B or C or D )always the led L1+L2turn ON AGAIN.L1+L2make a short flash,the magnet unlock for a while and remains OFF ,waiting for more buttons to receive.Then,after 4sec.,L1+L2turn back ON,the magnet locks again and the procedure ends.To memorise more transmitters it is necessary to use a transmitter already memorised for opening the memory.push the button of the new transmitter to memorise.button for 4SEC.button Repeat the steps 1and 2above,using the transmitter already memorised.When the led L1+L2turns OFF before 6 . Full memoryWhen the memory is full and you try to memorise another transmitter, the led L+L2 make 3 flashes and the operation fails.8. Unlock time setting ( fig. 6)The unlock time of the magnet is set by default to 4 sec. To modify this time proceed as follows:3) For setting the time desired, count the number of flashes and push P1 just after the flash corresponding to the release seconds desired.At the P1 release, the system will store the time corresponding to the number of flashes: L1 makes 3 short flashes and turns back ON.NOTE : the 10th flash lasts more then the others.1)Push simultaneously the buttons A +B of the transmitter and the led L1will make a SHORT FLASH.2)Release A+B and push the button B for 4SEC.until the led L1starts a SEQUENCE OF FLASHESAPPROVAL RELATIVE TO EMERGENCY EXITS:In the case of an installation of electromagnetic lock on emergency exits, it is imperative to make sure that these exit points will be automatically free in case of fire alarm, to open in the event of a fire alarm to allow evacuation of the premises.The electromagnetic lock installed on emergency exits must be in accordance with the fire approval department For more information, contact the local fire officer or the safety officer responsible for the building.POWER SUPPLY MOUNTING RECOMMENDATIONSAn electromagnetic lock always operates in DC current, a very low safety voltage. The Electromagnetic Lock is recommended for use with power supplies manufactured by Transmitter Solutions, however, other power supplies may be used on condition that they are of equivalent quality and characteristics rectified, filtered, regulated and protected by fuse in primary and secondary sectors.- Define the level of security of the access.- Determine the maximum strength of holding force to this level of security.- Select the Electromagnetic Lock according to the environment, the inside, the outside, the climatic constraints,(For example: stainless steel dedicated to an outside use).- Always install the electromagnetic lock on the secure side of the place to be secured.- Indeed make sure that the frame and opening, receiving or supporting the electromagnetic lock, armature plate and their accessories, are solid and resistant to damage or wear over a period of time.- Consider any bracketry required for the assembly according to the type of support receiving the electromagnetic lock and armature plate.- Define the passage of cables to ensure the protection against the vandalism and the environmental requirements (in particular through flexible hoses of door, glands, gutters, cross cables, plastic tubes).Armature plate - It is vital to fix the electromagnetic lock and armature plate solidly on their supports.- Make sure that the magnet and the armature meet evenly over their entire mating surfaces.- The Armature plate must be able to pivot slightly about its center mounting screw to compensate for any door misalignment.Security ropes The electromagnetic lock undergoes repeated shocks and the vibration at the points of fixation on the frame (frequencies of openings / closures, attempt of opening wears closed and attempts of vandalism) which can loosen the fixing bolts/screws. To prevent the risk of the electromagnetic block from falling, install both security ropes supplied, to guarantee the safety of the users (see attached plan).MAINTENANCE The Electromagnet and armature plate have a specific treatment which strengthens the protection against wear and corrosion.These products do not require high maintenance. Nevertheless to ensure optimum performance,it is recommended to clean regularly the surfaces in contact of the electro magnet and armature plate with a cloth and non abrasive products. If traces of corrosion appear, it is recommended to clean and oil the contact surfaces.Check and tighten regularly all the fixings of the Electromagnet and ensure that while the armature is able to pivot on its mou nting,the fixing bolt is not liable to loosen (we recommend thread-lock for all fixing bolts).Security rope (fixing on the magnetic lock and the frame)INSTALLATION Installation on an outward opening door (Push door)Installation on an inward opening door (Pull door)INSTALLATION WITH ACCESSORIESInstallation with an Armature housing Installation with base for glass doorArmature housing for glass doorInstallation with DPM300 - DPM400 - DPM500 (Door positionmonitoring)*300DPMFixed on the electromagnetic lock300DPM Fixed on the armatureRoll pinElectromagnetic lockArmature plateWARRANTY:The warranty period of Transmitter Solutions magnetic locks is twenty-four (24) months. This warranty shall begin on the date the keypad is manufactured. During the warranty period, the product will be repaired or replaced (at the sole discretion of Transmitter Solutions) if the product does not operate correctly due to a defective component. This warranty does not extend to (a) the case, which can be damaged by conditions outside the control of Transmitter Solutions, or (b) battery life. This warranty is further limited by the following disclaimer of warranty and liability:EXCEPT AS SET FORTH ABOVE, TRANSMITTER SOLUTIONS MAKES NO WARRANTIES REGARDING THE GOODS, EXPRESS OR IMPLIED, INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. BUYER MAKES NO RELIANCE ON ANY REPRESENTATION OF TRANSMITTER SOLUTIONS, EXPRESS OR IMPLIED, WITH REGARD TO THE GOODS AND ACCEPTS THEM “AS-IS/WHERE-IS”. TRANSMITTER SOLUTIONS SELLS THE GOODS TO BUYER ON CONDITION THAT TRANSMITTER SOLUTIONS WILL HAVE NO LIABILITY OF ANY KIND AS A RESULT OF THE SALE. BUYER AGREES THAT TRANSMITTER SOLUTIONS SHALL HAVE NO LIABILITY FOR DAMAGES OF ANY KIND, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO PERSONS OR PROPERTY, TO BUYER, ITS EMPLOYEES OR AGENTS, AS A RESULT OF THE SALE. BUYER ALSO AGREES TO HOLD TRANSMITTER SOLUTIONS HARMLESS FROM ANY CLAIMS BUYER, OR ANY THIRD PARTY, MAY HAVE AS A RESULT OF BUYER’S USE OR DISPOSAL OF THE GOODS. BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS TERMS IN CONSIDERATION OF RECEIVING THE GOODS.。
磁力锁 、电插锁 、电动开门机说明书
磁力锁电插锁电动开门机规格书技术参数（DAIC-MJ-DCLS）产品名称：280KG单门磁力锁（带信号输出)产品图片：产品概述：磁力锁（或称电磁锁）的设计和电磁铁一样，是利用电磁的原理，当电流通过硅钢片时，磁力锁会产生强大的吸力紧紧吸住铁板；只要非常小的电流就会让磁力锁产生很大的磁力，从而能有效地控制门的开关。
深圳多奥磁力锁采用国际领先的生产和封装工艺，不仅让磁力锁表面抗氧化能力达到国际领先水平，还使磁力锁的拉力远高于同类产品达20%以上。
我们的产品已远销到全球六十个国家或地区，且广泛应用于机场、地铁、银行、监狱、智能大厦、智能小区等重要场所，为全球用户提供方便、快捷、智能化的出入口管理锁具，受到了用户的广泛好评和青睐。
产品优势：◆ 250KG±10%静态直线拉力◆ 可自行设定12VDC±10% 或24VDC±10%◆ 内置反向电流保护装置（MOV）◆ 防残磁设计，防磨损材料制造◆ 铝外壳采用高强度合金材料◆ 双重锁体绝缘处理◆ 完全电磁吸力工作，不存在机械故障技术参数：锁体尺寸：长250x宽47x厚26(mm) 吸板尺寸：长180x宽38x厚11(mm) 工作电压：DC12V±10%/DC24V±10% 工作电流：480mA±5%/240mA±5%信号输出：锁状态信号输出延时开门：无安全类型：断电开门适用门型：木门\玻璃门\金属门\防火门等质量认证：CE/FCC/CMA/ROHS 选配支架：DA-280L/280U/280ZL产品尺寸：产品规格书（DAIC-MJ-LXS）产品名称：灵性锁（电机锁)产品图片：产品概述：电机锁(或称灵性锁)的设计有效结合了传统电控锁及磁力锁的优点，克服了电控锁噪音过大、磁力锁耗电等方面的不足而开发的新产品，电机锁与电控锁和磁力锁相比较，它的性能更加的完善、优点更加明显，可与楼宇对讲、门禁等智能化系统配套使用。
单管塔磁性防盗锁磁力锁产品技术手册
将锁舌挡板拆下，双锁紧螺母拆卸后，把锁旋转放入 D52mm 的门孔中，套上防水像皮止圈，拧上 M50 双锁紧螺母。
3：锁紧固定螺母组
将锁舌固定板套上锁具，拧上 M18 双锁紧螺母，固定后用钥匙调整档板的拉置即可使用。
4：安全性检查
本锁具内置磁性，具有很高的防盗性能，一般常规的方式无法将其打开，具有一定的防盗性能。 完成安装后,用专用磁性钥匙,检查开闭程度与锁紧度,如果较松,可适当调整楔形块的倾斜角度.
富阳佳淇通信技术有限公司-单管塔磁性防盗锁技术说明书
2、磁性锁及钥匙的磁体部分不得接触高温,油污,避免剧烈震动,以防失去磁性,导致功能丧失 3、锁体内部含有精密部件,请不要随意打开.确实需要更换零部件的,请及时与厂家联系. 4、为了保持锁具良好的性能,请勿置放于粉尘较多的环境下,不要将锁眼
堵塞,不得随意往锁体内添加黄油,润滑油,以防灰尘粘附. 5、锁具本体均为 SUS304 高强度不锈钢材质,工作环境在-15℃~+45℃之间,如果超过此环境,有
1：新产品：本产品是拥有知识产权的专利产品（专利证号 200920197683.9），是受法律保护的，在通信铁塔领域具有一定影响力的知名 品牌产品，可排除一切知识产权纠纷，客户可放心使用。
2：新材料：本产品主体材料为 304 高强度不锈钢，具有很强的抗冲 击与抗扭性，磁性材料采用钕铁硼强力磁铁，等级 N52，锁紧螺母与挡板固 定螺母均为高强度不锈钢细牙，防盗性能极高。
2：将锁舌挡板拆下，双锁紧螺母拆卸后，把锁旋转放下D50的门孔中， 套上防水像皮止圈，拧上M50双锁紧螺母。
3：将锁舌固定板套上锁具，拧上M18双锁紧螺母，固定后用钥匙调整档 板的拉置即可使用。
4：本锁具内置磁性，具有很高的防盗性能，一般常规的方式无法将其 打开，具有一定的防盗性能。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
磁力锁产品说明书
感谢您购买本公司生产的磁力锁。
为了更好地使用本产品，请在开始安装之前仔细阅读本说明书内容。
一、概述:
本磁力锁主要主材料来自国外进口,产品质量稳定可靠；符合公安消防要求；符合环保要求，工作时无噪声；防腐蚀，锁体经过特殊防锈处理；耐磨损，不会因为机械零件的磨损引起这种故障。
二、主要技术参数:
序号项目指标
1 工作电压DC12V±10%
2 工作电流350mA
3 工作环境湿度<90%
4 工作环境温度-20℃~50℃
5 吸力280KG
6 开锁方式通电上锁，断电开锁
7 门状态信号可选
三、安装步骤图:
四、线路板示意图:
注：上图中接电源的插座只需接一个，带LED磁力锁才具有门状态信号
五、注意事项：
1．磁力吸板的螺丝不要上的太紧，要让橡胶垫圈保持适当的弹性，使磁力吸板吸力自动调整到正确的位置。
2．磁力吸板安装要与锁体对正，以免吸力不够。
3．磁力锁工作时会产生较强磁场，请勿将对磁敏感元件靠近锁体。