GPS网复测成果书(最终版)

广东省东山(闽粤界）至潮州古巷公路控制网复测报告TJ4标测量复测成果编制：复核：审批：中铁四局集团有限公司广东省东山(闽粤界）至潮州古巷公路TJ4标2015年03月21日目录1.1工程简介 (3)1.2工作内容 (3)2.1技术依据及高程坐标系统 (4)2.1.1.测量数据依据 (4)2.1.2设计成果资料 (4)2.1.3高程坐标系统 (4)3.1仪器配备及计算软件 (4)3.1.1仪器配备 (4)3.1.2计算软件 (4)4.1.GPS静态测量要求 (5)4.2水准测量要求 (5)5.1 GPS外业观测的要求 (6)5.2水准观测 (6)6.1平面坐标 (6)6.2高程 (7)7.1测量仪器鉴定证书.............................. 错误！未定义书签。

7.2测量人员资质证书 (18)7.3 GPS评查计算表及成果 (19)8.1 交桩记录 (35)测量复测成果报告1.1工程简介本项目起点K0+000位于饶平县东山镇粤闽省界，与已建成的宁莞高速漳州至诏安段（原名福建省沈海高速复线）顺接，终点位于潮安区古巷镇，与在建的宁莞高速潮州至惠州段（简称潮惠高速）相连。

路线途经的主要城镇有饶平县东山镇、浮山镇、浮滨镇、樟溪镇，湘桥区磷溪镇、意溪镇，潮安区文祠镇、归湖镇、古巷镇等。

施工图阶段路线全长约64.561km。

广东省东山（粤闽界）至潮州古巷公路TJ4标段位于潮州市湘桥区意溪镇境内，起点里程K35+290，终点里程K43+400，主线长8.11km。

合同段内设置有意溪互通及项目管理中心，主线设特大桥1926.4m/1座，大桥573.7 m/4座，中桥65.0m/1座，通道桥30.3m/1座，涵洞1134.6m/21道。

本合同段总挖方240.1万m3，主线挖方147.7万m3，线内剩余坚石作为石料利用，合同段弃方约35.6万m3。

1.2工作内容自设计院2015年2月2日交桩以来，我部积极组织测量技术人员对沿线桩位进行重新踏勘，确定水准测量走向。

之后使用2台DSZ2自动安平水准仪采用两次置镜法的方式对设计院所交的控制点进行水准复测，最后使用6太天宝5800型接收机采用边连边式的观测方式对控制点进行平面坐标的复测。

2.1技术依据及高程坐标系统2.1.1测量技术依据1、《国家三、四等水准测量规范》（GB/T12898-2009)2、《工程测量规范》（GB/5006-2007)3、《全球定位系统(GPS)测量规范》(GB/T18314-2001)2.1.2设计成果资料广东省公路勘察规划设计院股份有限公司提供的《控制点成果表》2.1.3高程坐标系统潮漳高速公路采用1980年西安参考椭球，中央子午线116度45分，抵偿大地高100米，平均曲率半径为6363.7千米；1985国家高程基准。

3.1仪器配备及计算软件3.1.1仪器配备为满足控制网复测的精度要求，本次采用天宝GPS六台编号为：4850161650、4850161651、4850161849、4811147489、4811147497、4811147509；苏州一光DSZ2自动安平水准仪仪器编号为：366955、368741。

所有使用的仪器均在测前交送检测机构进行全面鉴定，且在鉴定的有限期内，各项指标均符合规范要求，作业过程中无异常情况发生。

表1 仪器的配置表3.1.2仪器配备东山至潮州古巷公路TJ4标平面坐标采用南方测绘公司的南方测绘GPS数据处理软件进行GPS的基线、三维网评差及二维约束评差。

高程的部分经过外业观测的成果，采用南方评差易软件对整体水准网进行评差。

4.1 GPS静态测量要求公路以及GPS静态测量要求见表2大于平均距离的两倍。

②特殊构筑物指对施工测量精度有特殊要求的桥梁，隧道等构筑物。

外业观测中按照公路一级等级进行外业观测。

具体要求详见表3。

表3 GPS静态观测要求4.2水准测量要求水准观测站限差要求见表5，水准观测限差要求见表6。

表5表6长度，以千米记；n为测段水准测量站数。

②当山区水准测量每公里测站数n≥25站时，采用测站数计算高差测量限差。

水准观测测单站视距≤75m，前后视距差≤2m，测段的前后视距累计差≤5m，最低视线高度要求三丝能读数。

5.1 GPS外业观测的要求1、观测中必须严格遵守调度命令，按规定的时间进行作业。

2、经检查接收机电源、电缆及天线等各项联接无误，方可开机。

3、接收机启动前与作业过程中，应随时逐项填写记录纸的内容。

4、每时段观测开始及结束前各记录一次观测卫星情况，天气状况。

5、每时段观测前后应各量取天线高一次。

两次量高之差不应大于3mm，取平均值作为天线高度。

6、观测期间防止仪器的震动，更不得移动，要防止人员及其他物体碰动天线及阻挡信号。

7、观测期内，不得在仪器附近50m内使用电台，10m以内使用对讲机。

8、一时段观测过程中不允许进行以下操作：a）接收机关闭又重启b）改变天线位置5.2水准规则1、观测前30min，将仪器置于露天阴影下，使仪器与外界温度趋于一致。

2、在连续各测站上安置水准仪的三脚架时，使其中两脚与水准线路方向平行，第三角轮换置于路线方向的左侧与右侧。

3、除路线转弯处之外，每一测站上仪器和前后视标尺的三个位置，接近一条直线。

4、不应为了增加尺读数，而把标尺安置在壕沟内。

5、每一测段的往测与返测，其测站数均为偶数，由往测转向返测时，两尺交换位置，并重新整平仪器。

6、观测至水准网的节点时，在观测手簿中的详细记录接测情况。

6.1平面坐标经过软件评差，计算评差后的坐标与设计坐标对比见表7。

表7为13.2mm。

经过二维约束评差后，采用复测后的控制点数据进行指导工作。

6.2高程高程按测段进行分析，测段间高差、闭合差、距离及允许闭合差详见表8：个控制点的水准点高程如表9。

本标段为满足施工生产要求埋设了几个加密水准点成果见表107.1测量仪器鉴定证书7.2测量人员资质证书7.3 GPS评差计算及成果重复基线长度差值比较,每部分第一行为参考基线及长度差限差(mm)，后续为重复基线及其与参考基线的差值(mm) ---------------------------------------------------------------------------------------------------- 序号起点终点 DX(m) DY(m) DZ(m) S(m) S限差/差值(mm) ----------------------------------------------------------------------------------------------------6 D2 D3 -85.5472 -55.4205 24.7766 104.8982 14.14314 D2 D3 -85.5493 -55.4182 24.7792 104.8993 1.1116 合格----------------------------------------------------------------------------------------------------33 GE86 GE83 -958.6423 -579.0763 16.0851 1120.0818 14.490528 GE86 GE83 -958.6516 -579.0853 16.0863 1120.0944 12.6298 合格----------------------------------------------------------------------------------------------------37 GE87 GE86 -491.8139 -114.8976 -194.8971 541.3569 14.222649 GE87 GE86 -491.8241 -114.9038 -194.8982 541.3678 10.9785 合格----------------------------------------------------------------------------------------------------57 BMD09 GE89 283.2609 59.2286 146.6183 324.4098 14.169761 BMD09 GE89 283.2666 59.2308 146.6156 324.4139 4.1584 合格----------------------------------------------------------------------------------------------------70 D5 GE91 -11.9356 -377.8445 772.8936 860.3914 14.947866 D5 GE91 -11.9431 -377.8337 772.9152 860.4062 14.7648 合格----------------------------------------------------------------------------------------------------79 BMD10 GE94 -397.4531 -158.8260 32.8625 429.2722 14.192083 BMD10 GE94 -397.4583 -158.8220 32.8489 429.2745 2.2937 合格----------------------------------------------------------------------------------------------------异步环闭合差计算结果环号,线路各点名...,X闭合差限差(mm),X闭合差(mm),Y闭合差限差(mm),Y闭合差(mm),Z闭合差限差(mm),Z闭合差(mm),S闭合差限差(mm),S闭合差(mm),线路总长度(m),ppm,备注1, D2 GE93 BMD10 , 26.43, -1.70, 26.43, 8.70, 26.43,3.50, 45.77, 9.53, 2785.9256, 3.42, 合格2, D3 D5 D2 , 26.25, -4.60, 26.25, 1.80, 26.25,1.70, 45.46, 5.22, 2151.0456,2.43, 合格3, D4 D2 D5 , 26.24, 0.90, 26.24, 0.80, 26.24,0.40, 45.45, 1.27, 2120.6772, 0.60, 合格4, D4 D2 GE92 , 26.25, -9.70, 26.25, 13.20, 26.25,5.20, 45.46, 17.19, 2148.6965, 8.00, 合格5, D6 BMD09 D5 , 26.23, 2.00, 26.23, -2.20, 26.23, -0.30, 45.43, 2.99, 2082.9616, 1.43, 合格6, D7 D6 BMD09 , 26.12, 0.00, 26.12, -0.50, 26.12, -0.60, 45.25, 0.78, 1574.5770, 0.50, 合格7, D8 GE87 BMD09 , 26.16, -0.30, 26.16, 0.00, 26.16,1.20, 45.31, 1.24, 1750.7632, 0.71, 合格8, GE79 GE83 GE78 , 27.43, -0.50, 27.43, -0.80, 27.43, -0.20, 47.51, 0.96, 5076.3391, 0.19, 合格9, GE81 GE83 GE78 , 27.37, -0.40, 27.37, 0.80, 27.37,0.60, 47.41, 1.08, 4979.2409, 0.22, 合格10, GE81 GE83 GE79 , 26.92, 0.10, 26.92, 0.60, 26.92,0.20, 46.63, 0.64, 4074.8776, 0.16, 合格11, GE84 GE83 D9 , 26.23, 0.20, 26.23, 1.20, 26.23, -5.40, 45.44, 5.54, 2093.7122, 2.64, 合格12, GE85 GE83 D9 , 26.23, -4.50, 26.23, -0.00, 26.23, -0.30, 45.44, 4.51, 2092.7213, 2.16, 合格13, GE85 GE83 GE84 , 26.13, -0.80, 26.13, -22.90, 26.13, -7.50, 45.25, 24.11, 1594.5516, 15.12, 合格14, GE86 GE83 GE87 , 26.59, 6.60, 26.59, 4.80, 26.59,5.80, 46.06, 10.01, 3279.3090, 3.05, 合格15, GE86 GE83 D9 , 26.34, -6.50, 26.34, 0.60, 26.34, -0.50, 45.62, 6.55, 2506.7779, 2.61, 合格16, GE86 GE83 GE84 , 26.28, -5.60, 26.28, -16.90, 26.28, -6.70, 45.51, 19.02, 2273.9765, 8.37, 合格17, GE86 GE83 GE85 , 26.30, 0.10, 26.30, 1.30, 26.30, -0.90, 45.55, 1.58, 2361.7289, 0.67, 合格18, GE86 GE83 GE81 , 27.10, -8.50, 27.10, -9.90, 27.10,1.20, 46.93, 13.10, 4440.1516,2.95, 合格19, GE86 GE83 GE79 , 28.15, -9.90, 28.15, -6.60, 28.15,1.30, 48.75, 11.97, 6250.4528, 1.91, 合格20, GE86 GE83 GE78 , 28.65, -7.50, 28.65, -9.00, 28.65,1.40, 49.63, 11.80, 6976.6631, 1.69, 合格21, GE87 GE83 GE85 , 26.59, 3.60, 26.59, 2.30, 26.59, -7.00, 46.05, 8.20, 3257.8591, 2.52, 合格22, GE87 GE83 D9 , 26.59, -4.50, 26.59, -1.30, 26.59, -7.00, 46.06, 8.42, 3268.3524, 2.58, 合格23, GE87 GE83 GE84 , 26.58, -5.00, 26.58, -17.80, 26.58, -9.00, 46.04, 20.56, 3247.0281, 6.33, 合格24, GE88 D8 GE87 , 26.09, 0.50, 26.09, -3.30, 26.09,0.40, 45.18, 3.36, 1354.3696, 2.48, 合格25, GE89 D5 BMD09 , 26.24, -1.90, 26.24, 1.50, 26.24,0.40, 45.44, 2.45, 2114.4744, 1.16, 合格26, GE91 D7 D6 , 26.24, -0.10, 26.24, 0.60, 26.24,0.50, 45.44, 0.79, 2103.9246, 0.37, 合格27, GE92 D2 D5 , 26.39, 4.40, 26.39, -1.50, 26.39,0.00, 45.72, 4.65, 2688.6406, 1.73, 合格28, GE94 GE93 BMD10 , 26.29, -3.50, 26.29, 7.50, 26.29,18.30, 45.54, 20.08, 2331.4131, 8.61, 合格29, GE94 GE93 D2 , 26.24, -6.30, 26.24, 3.40, 26.24,1.80, 45.45, 7.38, 2130.3736, 3.46, 合格30, GE95 D1 GE94 , 26.18, 0.20, 26.18, 0.00, 26.18, -0.30, 45.34, 0.36, 1847.0949, 0.20, 合格31, GE96 GE95 D1 , 26.07, 0.40, 26.07, -0.10, 26.07, -0.50, 45.16, 0.65, 1260.4126, 0.51, 合格32, D1 GE94 BMD10 , 26.15, -0.10, 26.15, 0.00, 26.15,0.20, 45.30, 0.22, 1733.8666, 0.13, 合格33, D3 D2 BMD10 , 26.12, -0.30, 26.12, 0.70, 26.12,0.50, 45.25, 0.91, 1575.3710, 0.58, 合格34, D4 D5 D3 , 26.20, 0.20, 26.20, -1.70, 26.20, -0.50, 45.39, 1.78, 1974.9909, 0.90, 合格35, D7 BMD09 D5 , 26.23, 2.00, 26.23, -1.70, 26.23, -0.10, 45.44, 2.63, 2097.3149, 1.25, 合格36, GE86 GE87 D8 , 26.17, 1.10, 26.17, 0.00, 26.17, -1.20, 45.32, 1.63, 1803.7282, 0.90, 合格37, GE86 GE87 BMD09 , 26.41, 0.80, 26.41, -0.70, 26.41,0.30, 45.75, 1.10, 2753.2198, 0.40, 合格38, GE88 GE87 BMD09 , 26.14, 0.50, 26.14, -0.60, 26.14, -0.40, 45.28, 0.88, 1674.3490, 0.52, 合格39, GE88 GE87 GE86 , 26.30, 0.20, 26.30, -1.10, 26.30, -0.80, 45.55, 1.37, 2354.0482, 0.58, 合格40, GE89 BMD09 D7 , 26.04, -1.10, 26.04, 0.60, 26.04, -1.80, 45.10, 2.19, 980.1109, 2.24, 合格41, GE89 BMD09 D6 , 26.13, -1.50, 26.13, 1.80, 26.13,0.20, 45.25, 2.35, 1591.6374, 1.48, 合格42, GE89 BMD09 D8 , 26.15, 7.20, 26.15, -3.40, 26.15, -2.90, 45.29, 8.47, 1708.8323, 4.96, 合格-2.70, 45.53, 7.40, 2317.7291, 3.19, 合格44, GE91 D6 BMD09 , 26.48, 1.10, 26.48, -1.80, 26.48, -1.00, 45.86, 2.33, 2953.5150, 0.79, 合格45, GE91 D6 D5 , 26.21, 2.30, 26.21, -2.90, 26.21, -1.30, 45.39, 3.92, 1986.6961, 1.97, 合格46, GE92 D5 D3 , 26.35, -1.70, 26.35, 0.00, 26.35,1.10, 45.63,2.02, 2526.9396, 0.80, 合格47, GE93 D2 D3 , 26.20, 6.50, 26.20, -7.30, 26.20, -2.30, 45.38, 10.04, 1942.7663, 5.17, 合格48, GE94 D2 D3 , 26.03, 0.30, 26.03, -0.60, 26.03, -0.10, 45.09, 0.68, 962.1072, 0.70, 合格49, GE95 GE94 BMD10 , 26.10, 0.00, 26.10, -0.10, 26.10,0.10, 45.20, 0.14, 1417.7825, 0.10, 合格50, GE96 D1 GE94 , 26.22, -0.00, 26.22, 0.10, 26.22,0.00, 45.42, 0.10, 2045.6060, 0.05, 合格51, D4 D5 GE91 , 26.20, -9.40, 26.20, 10.60, 26.20,23.60, 45.39, 27.53, 1966.6574, 14.00, 合格52, GE89 GE87 GE88 , 26.29, 0.30, 26.29, -2.50, 26.29, -0.40, 45.53, 2.55, 2316.0713, 1.10, 合格53, GE89 GE87 GE86 , 26.64, -0.50, 26.64, -0.60, 26.64,0.10, 46.14, 0.79, 3398.0410, 0.23, 合格54, GE91 BMD09 GE89 , 26.38, -0.10, 26.38, 0.00, 26.38,0.80, 45.69, 0.81, 2644.7783, 0.30, 合格55, GE91 D5 D2 , 26.52, 7.10, 26.52, -9.10, 26.52, -23.30, 45.93, 26.00, 3073.2893, 8.46, 合格56, GE91 D5 D3 , 26.46, 6.80, 26.46, -11.40, 26.46, -20.70, 45.83, 24.59, 2895.7656, 8.49, 合格57, GE92 D5 GE91 , 26.37, -9.70, 26.37, 8.60, 26.37,23.00, 45.67, 26.40, 2604.1731, 10.14, 合格58, GE96 GE94 BMD10 , 26.19, -0.30, 26.19, -0.00, 26.19,0.20, 45.35, 0.36, 1884.8883, 0.19, 合格----------------------------------------------------------------------------------潮州二维网平差结果多余观测数= 130已知点数= 3总点数= 27GPS基线向量数= 90地面边长数= 0地面方位角数= 0旋转角(GPS->地面)= -0.000080245(dms)尺度(GPS->地面)= 16.7509(ppm)中央子午线= 116.450000000(dms)椭球长轴= 6378140.000(m)椭球扁率分母= 298.257000000M0= 0.418(cm)----------------------------------------------------------------------------------已知坐标(X,Y)---------------------------------------------------------------------------------- No. Name X(m) Y(m)----------------------------------------------------------------------------------1 GE78 2623751.6710 502274.77402 GE96 2624738.7520 494531.45903 GE87 2623386.8980 498354.1030----------------------------------------------------------------------------------GPS二维基线向量---------------------------------------------------------------------------------- No. From To VectorDX(m) VectorDY(m) Distance(m) ----------------------------------------------------------------------------------1 GE87 BMD09 342.090 -756.590 830.3342 BMD10 D1 203.494 -403.817 452.1923 BMD10 D2 -356.447 598.640 696.7244 D2 D3 27.103 101.337 104.8995 BMD10 D3 -329.344 699.976 773.5856 D2 D3 27.102 101.336 104.8987 D2 D4 -358.971 675.109 764.6138 D3 D4 -386.073 573.775 691.5719 D5 D4 156.120 -250.580 295.23510 GE91 D4 -685.043 -431.307 809.51211 GE92 D4 -761.667 258.414 804.31012 BMD09 D5 157.863 -1028.710 1040.75213 D3 D5 -542.194 824.354 986.67814 D2 D5 -515.091 925.688 1059.34715 BMD09 D6 139.243 -766.733 779.27416 D5 D6 -18.619 261.976 262.63717 D6 D7 21.241 312.944 313.66418 BMD09 D7 160.483 -453.789 481.33119 D5 D7 2.622 574.920 574.92620 GE87 D8 299.916 -219.696 371.77421 BMD09 D8 -42.173 536.895 538.54922 GE78 GE79 -618.804 -307.566 691.02523 GE78 GE81 -828.620 -1236.999 1488.88524 GE79 GE81 -209.816 -929.432 952.82025 GE87 GE83 -177.045 1607.567 1617.28726 D9 GE83 -267.296 1010.744 1045.49127 GE84 GE83 -111.386 317.476 336.44928 GE86 GE83 49.157 1116.666 1117.74729 GE85 GE83 -219.332 765.427 796.23230 GE81 GE83 286.797 -1076.047 1113.61132 GE79 GE83 76.981 -2005.478 2006.95533 GE86 GE83 49.154 1116.653 1117.73534 D9 GE84 -155.916 693.267 710.58335 D9 GE85 -47.965 245.321 249.96636 GE84 GE85 107.947 -447.940 460.76337 GE87 GE86 -226.197 490.893 540.50138 D8 GE86 -526.114 710.588 884.15539 BMD09 GE86 -568.287 1247.483 1370.82640 D9 GE86 -316.455 -105.916 333.71041 GE84 GE86 -160.544 -799.177 815.14342 GE85 GE86 -268.490 -351.239 442.10443 GE81 GE86 237.643 -2192.700 2205.54144 GE79 GE86 27.825 -3122.132 3122.25645 GE78 GE86 -590.977 -3429.701 3480.24446 GE85 GE87 -42.294 -842.144 843.20547 D9 GE87 -90.258 -596.818 603.60448 GE84 GE87 65.656 -1290.078 1291.74849 GE86 GE87 226.198 -490.905 540.51250 D8 GE88 -10.868 -342.930 343.10251 GE87 GE88 289.049 -562.625 632.53152 BMD09 GE88 -53.041 193.966 201.08753 GE86 GE88 515.246 -1053.517 1172.76554 D5 GE89 6.380 749.101 749.12855 D7 GE89 3.756 174.182 174.22256 D6 GE89 24.998 487.126 487.76757 BMD09 GE89 164.242 -279.608 324.27858 GE88 GE89 217.281 -473.580 521.04659 D8 GE89 206.416 -816.508 842.19560 GE87 GE89 506.330 -1036.205 1153.29661 BMD09 GE89 164.240 -279.614 324.28262 GE86 GE89 732.527 -1527.098 1693.70163 D7 GE91 838.557 -394.188 926.58664 BMD09 GE91 999.041 -847.978 1310.40065 D6 GE91 859.798 -81.245 863.62866 D5 GE91 841.180 180.731 860.37667 GE89 GE91 834.800 -568.370 1009.91868 D2 GE91 326.072 1106.417 1153.46569 D3 GE91 298.972 1005.084 1048.60870 D5 GE91 841.165 180.729 860.36171 D2 GE92 402.694 416.698 579.48372 GE91 GE92 76.623 -689.719 693.96273 D5 GE92 917.786 -508.993 1049.47974 D3 GE92 375.593 315.363 490.43275 D2 GE93 849.731 424.849 950.02177 BMD10 GE93 493.285 1023.491 1136.16278 D3 GE93 822.630 323.510 883.95679 BMD10 GE94 15.173 426.440 426.71080 D1 GE94 -188.321 830.256 851.34681 D2 GE94 371.606 -172.198 409.56482 D3 GE94 344.502 -273.535 439.89083 BMD10 GE94 15.158 426.443 426.71284 D1 GE95 174.533 351.491 392.43885 GE96 GE95 397.707 460.630 608.56586 BMD10 GE95 378.027 -52.326 381.63187 GE94 GE95 362.854 -478.765 600.73288 D1 GE96 -223.174 -109.139 248.43189 BMD10 GE96 -19.680 -512.956 513.33390 GE94 GE96 -34.853 -939.395 940.042--------------------------------------------------------------------------------------平差坐标(X,Y)-------------------------------------------------------------------------------------- No. Name X(m) Y(m) Mx(cm) My(cm) Mp(cm)--------------------------------------------------------------------------------------1 GE78 2623751.6710 502274.77402 GE96 2624738.7520 494531.45903 GE87 2623386.8980 498354.10304 BMD09 2623728.9976 497597.5018 0.14 0.14 0.205 BMD10 2624758.4320 495044.4232 0.09 0.10 0.146 D1 2624961.9292 494640.6008 0.11 0.12 0.167 D2 2624401.9808 495643.0725 0.14 0.15 0.218 D3 2624429.0836 495744.4100 0.14 0.15 0.219 D4 2624042.9988 496318.1927 0.26 0.23 0.3410 D5 2623886.8694 496568.7740 0.17 0.16 0.2311 GE91 2624728.0581 496749.5120 0.16 0.15 0.2212 GE92 2624804.6810 496059.7791 0.30 0.25 0.3913 D6 2623868.2479 496830.7547 0.18 0.17 0.2514 D7 2623889.4867 497143.7040 0.20 0.18 0.2715 D8 2623686.8205 498134.4063 0.24 0.25 0.3416 GE79 2623132.8575 501967.1999 0.22 0.26 0.3417 GE81 2622923.0415 501037.7530 0.14 0.15 0.2018 GE83 2623209.8470 499961.6904 0.12 0.13 0.1719 D9 2623477.1551 498950.9303 0.17 0.17 0.2420 GE84 2623321.2363 499644.2045 0.26 0.19 0.3221 GE86 2623160.6958 498845.0091 0.14 0.14 0.2022 GE85 2623429.1883 499196.2565 0.16 0.16 0.2323 GE88 2623675.9547 497791.4722 0.20 0.20 0.2824 GE89 2623893.2430 497317.8876 0.16 0.15 0.2225 GE93 2625251.7246 496067.9322 0.32 0.39 0.5027 GE95 2625136.4637 494992.0985 0.11 0.12 0.17--------------------------------------------------------------------------------------最弱点-------------------------------------------------------------------------------------- No. Name MX(cm) MY(cm) MP(cm)--------------------------------------------------------------------------------------25 GE93 0.32 0.39 0.50--------------------------------------------------------------------------------------误差椭圆参数(E,F,T)-------------------------------------------------------------------------------------- No. Name E(cm) F(cm) T(dms)--------------------------------------------------------------------------------------1 GE78 0.00 0.00 0.00002 GE96 0.00 0.00 0.00003 GE87 0.00 0.00 0.00004 BMD09 0.14 0.14 28.58415 BMD10 0.10 0.09 116.56146 D1 0.12 0.11 117.43327 D2 0.15 0.14 97.41138 D3 0.15 0.14 97.01229 D4 0.26 0.23 4.361110 D5 0.17 0.16 155.522711 GE91 0.16 0.15 156.502912 GE92 0.30 0.25 10.375413 D6 0.18 0.16 153.540414 D7 0.21 0.17 154.514015 D8 0.26 0.22 49.103716 GE79 0.26 0.22 96.135217 GE81 0.15 0.14 95.540618 GE83 0.13 0.12 102.533319 D9 0.18 0.17 123.215620 GE84 0.26 0.18 165.553721 GE86 0.14 0.14 84.443822 GE85 0.16 0.16 118.054023 GE88 0.21 0.19 40.204024 GE89 0.16 0.15 171.483725 GE93 0.39 0.32 98.162126 GE94 0.12 0.11 113.411927 GE95 0.13 0.11 117.5913--------------------------------------------------------------------------------------二维基线向量残差-------------------------------------------------------------------------------------- No. From To V_DX(cm) V_DY(cm)--------------------------------------------------------------------------------------2 BMD10 D1 -0.18 0.033 BMD10 D2 0.41 0.114 D2 D3 -0.07 -0.115 BMD10 D3 0.33 -0.006 D2 D3 0.05 -0.037 D2 D4 -0.28 0.088 D3 D4 -0.26 -0.089 D5 D4 0.54 0.1810 GE91 D4 -0.63 -0.2611 GE92 D4 -0.18 -0.1912 BMD09 D5 0.26 -0.1013 D3 D5 -0.80 -0.2014 D2 D5 -0.85 0.0115 BMD09 D6 0.19 -0.1616 D5 D6 -0.16 0.0217 D6 D7 -0.12 0.0118 BMD09 D7 0.12 -0.1719 D5 D7 -0.23 0.0320 GE87 D8 0.08 0.1521 BMD09 D8 -0.08 0.0722 GE78 GE79 -0.02 -0.0123 GE78 GE81 -0.05 0.1824 GE79 GE81 -0.01 0.1625 GE87 GE83 0.32 -0.5726 D9 GE83 -0.34 0.0027 GE84 GE83 -0.03 0.4628 GE86 GE83 -0.23 -0.3429 GE85 GE83 -0.25 -0.5130 GE81 GE83 -0.01 0.1031 GE78 GE83 -0.05 0.2832 GE79 GE83 -0.03 0.2233 GE86 GE83 0.03 0.8934 D9 GE84 0.23 -0.3835 D9 GE85 0.02 0.1236 GE84 GE85 0.10 -0.1337 GE87 GE86 0.06 0.5838 D8 GE86 0.08 0.5339 BMD09 GE86 -0.06 0.5740 D9 GE86 0.08 -0.2141 GE84 GE86 0.31 -0.4742 GE85 GE86 0.11 -0.1143 GE81 GE86 -0.09 -0.7644 GE79 GE86 0.03 -0.6345 GE78 GE86 -0.13 -0.4547 D9 GE87 0.02 0.1148 GE84 GE87 -0.06 -0.2249 GE86 GE87 -0.13 0.6150 D8 GE88 0.14 0.1851 GE87 GE88 0.06 0.2152 BMD09 GE88 0.01 0.1853 GE86 GE88 0.02 -0.3954 D5 GE89 -0.35 -0.0355 D7 GE89 0.05 -0.1356 D6 GE89 -0.17 -0.1357 BMD09 GE89 -0.05 -0.2358 GE88 GE89 0.14 0.2159 D8 GE89 0.04 0.1960 GE87 GE89 0.25 0.5161 BMD09 GE89 0.17 0.3862 GE86 GE89 0.17 -0.1363 D7 GE91 -0.11 -0.0564 BMD09 GE91 -0.05 -0.1665 D6 GE91 -0.25 -0.0366 D5 GE91 -0.43 0.0867 GE89 GE91 -0.07 0.0568 D2 GE91 0.39 0.3169 D3 GE91 0.14 -0.0470 D5 GE91 1.02 0.2671 D2 GE92 0.06 -0.0072 GE91 GE92 -0.40 -0.2573 D5 GE92 0.79 0.3174 D3 GE92 -0.07 -0.0475 D2 GE93 -0.03 -0.0076 GE94 GE93 -0.36 -0.2977 BMD10 GE93 0.36 -0.1478 D3 GE93 -0.14 0.3679 BMD10 GE94 -0.62 0.1880 D1 GE94 -0.47 0.1481 D2 GE94 0.40 -0.1382 D3 GE94 0.45 -0.0183 BMD10 GE94 0.86 -0.1184 D1 GE95 -0.01 -0.0185 GE96 GE95 -0.01 0.0386 BMD10 GE95 -0.16 0.0487 GE94 GE95 0.48 -0.1288 D1 GE96 0.03 -0.0189 BMD10 GE96 -0.14 -0.0090 GE94 GE96 0.50 -0.15二维基线向量可靠性-------------------------------------------------------------------------------------- No. From To 内部可靠性DX DY--------------------------------------------------------------------------------------1 GE87 BMD09 0.69 0.692 BMD10 D1 0.66 0.653 BMD10 D2 0.69 0.714 D2 D3 0.70 0.785 BMD10 D3 0.74 0.766 D2 D3 0.76 0.677 D2 D4 0.80 0.798 D3 D4 0.77 0.779 D5 D4 0.56 0.5610 GE91 D4 0.85 0.8511 GE92 D4 0.65 0.6312 BMD09 D5 0.82 0.8113 D3 D5 0.82 0.8114 D2 D5 0.83 0.8215 BMD09 D6 0.78 0.7816 D5 D6 0.31 0.3117 D6 D7 0.73 0.7318 BMD09 D7 0.69 0.6619 D5 D7 0.82 0.8120 GE87 D8 0.47 0.4521 BMD09 D8 0.82 0.8222 GE78 GE79 0.52 0.5223 GE78 GE81 0.54 0.5424 GE79 GE81 0.73 0.7325 GE87 GE83 0.62 0.6126 D9 GE83 0.82 0.8227 GE84 GE83 0.80 0.7228 GE86 GE83 0.89 0.8829 GE85 GE83 0.78 0.7830 GE81 GE83 0.20 0.2031 GE78 GE83 0.65 0.6732 GE79 GE83 0.77 0.7733 GE86 GE83 0.92 0.9334 D9 GE84 0.70 0.7335 D9 GE85 0.41 0.4436 GE84 GE85 0.69 0.6237 GE87 GE86 0.90 0.9038 D8 GE86 0.89 0.9039 BMD09 GE86 0.71 0.7041 GE84 GE86 0.85 0.8042 GE85 GE86 0.68 0.7243 GE81 GE86 0.91 0.9244 GE79 GE86 0.78 0.8145 GE78 GE86 0.81 0.8446 GE85 GE87 0.64 0.6947 D9 GE87 0.68 0.7048 GE84 GE87 0.75 0.6949 GE86 GE87 0.90 0.9150 D8 GE88 0.83 0.8451 GE87 GE88 0.76 0.7452 BMD09 GE88 0.57 0.5953 GE86 GE88 0.72 0.7254 D5 GE89 0.86 0.8555 D7 GE89 0.75 0.7356 D6 GE89 0.82 0.8357 BMD09 GE89 0.83 0.8158 GE88 GE89 0.74 0.7459 D8 GE89 0.81 0.8260 GE87 GE89 0.84 0.8561 BMD09 GE89 0.77 0.8162 GE86 GE89 0.81 0.8263 D7 GE91 0.62 0.6164 BMD09 GE91 0.67 0.6765 D6 GE91 0.71 0.7266 D5 GE91 0.76 0.7667 GE89 GE91 0.70 0.7068 D2 GE91 0.71 0.6769 D3 GE91 0.64 0.6270 D5 GE91 0.92 0.9271 D2 GE92 0.74 0.7472 GE91 GE92 0.71 0.7173 D5 GE92 0.92 0.9174 D3 GE92 0.76 0.7575 D2 GE93 0.75 0.7676 GE94 GE93 0.80 0.8077 BMD10 GE93 0.67 0.6878 D3 GE93 0.71 0.7279 BMD10 GE94 0.75 0.7480 D1 GE94 0.82 0.8181 D2 GE94 0.63 0.6682 D3 GE94 0.66 0.7083 BMD10 GE94 0.76 0.7884 D1 GE95 0.29 0.3086 BMD10 GE95 0.66 0.6687 GE94 GE95 0.81 0.8088 D1 GE96 0.66 0.6689 BMD10 GE96 0.46 0.4790 GE94 GE96 0.69 0.70累计内部可靠性 65.00 65.00平均内部可靠性 0.72 0.72内部可靠性总和 130.00内部可靠性均值 0.72--------------------------------------------------------------------------------------------------平差后方位角、边长及精度-------------------------------------------------------------------------------------------------- No. FROM TO A(dms) MA(s) S(m) MS(cm) MS:S ppm --------------------------------------------------------------------------------------------------1 GE87 BMD09 294.19489 0.36 830.3478 0.14 1/602000 1.662 BMD10 D1 296.44412 0.48 452.1986 0.12 1/380000 2.633 BMD10 D2 120.46144 0.40 696.7342 0.14 1/497000 2.014 D2 D3 75.01360 2.36 104.8992 0.12 1/86000 11.505 BMD10 D3 115.11503 0.37 773.5968 0.14 1/538000 1.866 D2 D3 75.01360 2.36 104.8992 0.12 1/86000 11.507 D2 D4 118.00034 0.64 764.6275 0.21 1/362000 2.768 D3 D4 123.56084 0.70 691.5837 0.21 1/324000 3.089 D5 D4 301.55327 1.60 295.2412 0.21 1/142000 7.0010 GE91 D4 212.11415 0.54 809.5323 0.23 1/345000 2.8911 GE92 D4 161.15347 0.69 804.3241 0.30 1/264000 3.7812 BMD09 D5 278.43290 0.29 1040.7710 0.14 1/764000 1.3113 D3 D5 123.20037 0.33 986.6976 0.16 1/633000 1.5814 D2 D5 119.05383 0.31 1059.3691 0.16 1/681000 1.4715 BMD09 D6 280.17362 0.40 779.2892 0.14 1/548000 1.8216 D5 D6 94.03566 0.95 262.6417 0.11 1/246000 4.0617 D6 D7 86.07030 1.21 313.6692 0.14 1/221000 4.5118 BMD09 D7 289.28355 0.67 481.3410 0.16 1/299000 3.3419 D5 D7 89.44210 0.64 574.9360 0.14 1/400000 2.5020 GE87 D8 323.46364 1.47 371.7797 0.22 1/167000 5.9621 BMD09 D8 94.29302 0.98 538.5586 0.26 1/210000 4.7622 GE78 GE79 206.25449 0.75 691.0369 0.22 1/310000 3.2223 GE78 GE81 236.11006 0.20 1488.9083 0.14 1/1032000 0.9724 GE79 GE81 257.16448 0.50 952.8349 0.26 1/366000 2.7325 GE87 GE83 96.17057 0.15 1617.3077 0.13 1/1288000 0.7826 D9 GE83 104.48484 0.37 1045.5092 0.19 1/548000 1.8227 GE84 GE83 109.19600 1.54 336.4593 0.22 1/152000 6.5528 GE86 GE83 87.28470 0.29 1117.7624 0.17 1/672000 1.4929 GE85 GE83 105.59243 0.46 796.2409 0.18 1/443000 2.2630 GE81 GE83 284.55272 0.20 1113.6284 0.12 1/913000 1.0931 GE78 GE83 256.48596 0.10 2375.6955 0.12 1/1908000 0.5232 GE79 GE83 272.11544 0.23 2006.9868 0.26 1/768000 1.3033 GE86 GE83 87.28470 0.29 1117.7624 0.17 1/672000 1.4934 D9 GE84 102.40301 0.74 710.5911 0.22 1/320000 3.1235 D9 GE85 101.03470 1.35 249.9715 0.17 1/148000 6.7536 GE84 GE85 283.32581 1.12 460.7722 0.21 1/220000 4.5337 GE87 GE86 114.44223 0.53 540.5148 0.14 1/380000 2.6338 D8 GE86 126.30574 0.66 884.1739 0.25 1/355000 2.8139 BMD09 GE86 114.29299 0.26 1370.8543 0.16 1/833000 1.2040 D9 GE86 198.30208 1.19 333.7151 0.19 1/179000 5.5941 GE84 GE86 258.38302 0.69 815.1604 0.20 1/402000 2.4842 GE85 GE86 232.36209 0.83 442.1119 0.18 1/249000 4.0143 GE81 GE86 276.11085 0.16 2205.5850 0.19 1/1182000 0.8544 GE79 GE86 270.30391 0.16 3122.3149 0.28 1/1132000 0.8845 GE78 GE86 260.13246 0.08 3480.3073 0.14 1/2432000 0.4146 GE85 GE87 267.07307 0.39 843.2147 0.16 1/519000 1.9347 D9 GE87 261.24015 0.59 603.6135 0.17 1/349000 2.8648 GE84 GE87 272.54491 0.41 1291.7714 0.19 1/675000 1.4849 GE86 GE87 294.44223 0.53 540.5148 0.14 1/380000 2.6350 D8 GE88 268.11068 1.70 343.1061 0.29 1/117000 8.4951 GE87 GE88 297.11321 0.67 632.5402 0.19 1/329000 3.0452 BMD09 GE88 105.17388 2.03 201.0922 0.19 1/107000 9.3253 GE86 GE88 296.03436 0.38 1172.7880 0.21 1/568000 1.7654 D5 GE89 89.30451 0.45 749.1407 0.14 1/534000 1.8755 D7 GE89 88.45526 2.19 174.2241 0.15 1/116000 8.6056 D6 GE89 87.03457 0.72 487.7737 0.14 1/341000 2.9257 BMD09 GE89 300.25479 0.80 324.2848 0.14 1/240000 4.1658 GE88 GE89 294.38471 0.83 521.0534 0.20 1/262000 3.8159 D8 GE89 284.11152 0.66 842.2072 0.26 1/328000 3.0460 GE87 GE89 296.02325 0.28 1153.3116 0.16 1/739000 1.3561 BMD09 GE89 300.25479 0.80 324.2848 0.14 1/240000 4.1662 GE86 GE89 295.37359 0.22 1693.7312 0.18 1/939000 1.0663 D7 GE91 334.49225 0.28 926.6010 0.18 1/511000 1.9564 BMD09 GE91 319.40330 0.18 1310.4231 0.15 1/898000 1.1165 D6 GE91 354.36079 0.29 863.6399 0.15 1/573000 1.7466 D5 GE91 12.07344 0.30 860.3863 0.13 1/650000 1.5467 GE89 GE91 325.45050 0.25 1009.9343 0.16 1/632000 1.5868 D2 GE91 73.34455 0.27 1153.4880 0.14 1/827000 1.2169 D3 GE91 73.26043 0.29 1048.6256 0.14 1/762000 1.3170 D5 GE91 12.07344 0.30 860.3863 0.13 1/650000 1.5471 D2 GE92 45.58454 0.88 579.4927 0.27 1/215000 4.6472 GE91 GE92 276.20205 0.85 693.9758 0.23 1/307000 3.2673 D5 GE92 330.59181 0.51 1049.5017 0.28 1/381000 2.6274 D3 GE92 40.01062 1.02 490.4397 0.27 1/178000 5.5975 D2 GE93 26.33518 0.82 950.0369 0.32 1/295000 3.3976 GE94 GE93 51.18438 0.94 764.9096 0.35 1/220000 4.5477 BMD10 GE93 64.16037 0.60 1136.1814 0.36 1/313000 3.1978 D3 GE93 21.28061 0.89 883.9711 0.32 1/279000 3.5879 BMD10 GE94 87.57479 0.47 426.7182 0.11 1/390000 2.5680 D1 GE94 102.46489 0.30 851.3630 0.14 1/615000 1.6381 D2 GE94 335.08161 0.74 409.5753 0.13 1/306000 3.2682 D3 GE94 321.33036 0.68 439.9010 0.14 1/316000 3.1683 BMD10 GE94 87.57479 0.47 426.7182 0.11 1/390000 2.5684 D1 GE95 63.35367 0.52 392.4448 0.10 1/407000 2.4585 GE96 GE95 49.11348 0.42 608.5749 0.11 1/544000 1.8486 BMD10 GE95 352.07104 0.62 381.6357 0.11 1/347000 2.8787 GE94 GE95 307.09317 0.42 600.7462 0.14 1/438000 2.2888 D1 GE96 206.03372 1.02 248.4351 0.11 1/231000 4.3289 BMD10 GE96 267.48105 0.37 513.3416 0.10 1/513000 1.9590 GE94 GE96 267.52326 0.25 940.0589 0.12 1/779000 1.28 --------------------------------------------------------------------------------------------------最弱边-------------------------------------------------------------------------------------------------- No. FROM TO A(dms) MA(s) S(m) MS(cm) MS:S ppm -------------------------------------------------------------------------------------------------- 4 D2 D3 75.01360 2.36 104.8992 0.12 1/86000 11.50 --------------------------------------------------------------------------------------------------相邻点坐标分量及其相对中误差-------------------------------------------------------------------------------------------------- No. FROM TO dX(m) dY(m) mdX(cm) mdY(cm) --------------------------------------------------------------------------------------------------1 GE87 BMD09 342.0996 -756.6012 0.14 0.14 合格2 BMD10 D1 203.4971 -403.8224 0.11 0.12 合格3 BMD10 D2 -356.4512 598.6494 0.13 0.14 合格4 D2 D3 27.1027 101.3375 0.12 0.12 合格5 BMD10 D3 -329.3485 699.9868 0.14 0.15 合格6 D2 D3 27.1027 101.3375 0.12 0.12 合格7 D2 D4 -358.9820 675.1202 0.24 0.21 合格8 D3 D4 -386.0847 573.7827 0.24 0.20 合格9 D5 D4 156.1294 -250.5813 0.24 0.20 合格10 GE91 D4 -685.0593 -431.3193 0.24 0.20 合格11 GE92 D4 -761.6822 258.4136 0.32 0.25 合格12 BMD09 D5 157.8718 -1028.7278 0.15 0.13 合格13 D3 D5 -542.2142 824.3640 0.17 0.15 合格14 D2 D5 -515.1114 925.7015 0.17 0.15 合格15 BMD09 D6 139.2503 -766.7471 0.16 0.13 合格16 D5 D6 -18.6215 261.9807 0.12 0.10 合格17 D6 D7 21.2388 312.9493 0.18 0.15 合格18 BMD09 D7 160.4891 -453.7978 0.17 0.14 合格19 D5 D7 2.6173 574.9300 0.18 0.14 合格20 GE87 D8 299.9225 -219.6967 0.24 0.25 合格。