设置hcsecpathf系列防火墙的web访问终审稿)

设置H3C SecPath F100 系列防火墙的web访问

精心整理设置H3CSecPathF100系列防火墙的web访问
最近集团下属酒店退回一台H3CSecPathF100-S防火墙，自我学习巩固的同时，给大家带来几篇教程，欢迎大家的拍砖。

今天给大家带来的是如何实现通过Web方式访问和配置路由器。

和H3C之前的产品不同，H3C在SecPathF100系列防火墙产品中增加了更加人性
化的
WEB
墙自带
自带
第三步：
输入“system-view”命令，进入高级管理模式，我们首先查看一下防火墙默认的配置信息
第四步：下面开始配置：
精心整理
??????启动防火墙的HTTP服务，默认情况下是开启的，我们不用操作。

命令：undoiphttpshutdown
在防火墙中新建相应的用户，授于用户telnet的权限，管理权限设为最高的3级。

local-useradmin?????????????(新建用户admin)
Quit。

H3C SecPath F100系列防火墙配置教程

H3C SecPath F100系列防火墙配置教程初始化配置〈H3C〉system-view开启防火墙功能[H3C]firewall packet-filter enable[H3C]firewall packet-filter default permit分配端口区域[H3C] firewall zone untrust[H3C-zone-trust] add interface GigabitEthernet0/0[H3C] firewall zone trust[H3C-zone-trust] add interface GigabitEthernet0/1工作模式firewall mode transparent 透明传输firewall mode route 路由模式http 服务器使能HTTP 服务器 undo ip http shutdown关闭HTTP 服务器 ip http shutdown添加WEB用户[H3C] local-user admin[H3C-luser-admin] password simple admin[H3C-luser-admin] service-type telnet[H3C-luser-admin] level 3开启防范功能firewall defend all 打开所有防范切换为中文模式 language-mode chinese设置防火墙的名称 sysname sysname配置防火墙系统IP 地址 firewall system-ip system-ip-address [ address-mask ] 设置标准时间 clock datetime time date设置所在的时区 clock timezone time-zone-name { add | minus } time取消时区设置 undo clock timezone配置切换用户级别的口令 super password [ level user-level ] { simple | cipher } password取消配置的口令 undo super password [ level user-level ]缺缺省情况下，若不指定级别，则设置的为切换到3 级的密码。

web配置H3C防火墙

1、先启动模式器,连接设备，如果是真实环境直接连接设备即可，桥接好物理网卡。

组网图
如下：
2、然后配置物理网卡的地址，这里配置的是10.10.10.2，真实机器防火墙默认是管理地址
为192.168.0.1/账号密码均为admin，只有管理口才是这个地址。

3、创建安全域，防火墙需要安全域才能转发。

（真机不用创建安全域）
4、接口加入管理安全域内，真实环境管理域已经绑定了管理口。

5、创建ip安全策略：
6、定义rule 名字为fangxing,配置动作为pass ，指定放行的源目安全区域。

7、在设备上ping电脑网卡的管理地址。

8、浏览器输入10.10.18.1即可
9、输入账号密码admin/admin登陆
10、新版本需要强制修改密码，老款防火墙则不需要。

11、进入配置页面后，首次配置有向导跳转，不熟悉配置按照配置来即可。

12、自由选择部署模式，这里选择的是路由模式，因为部署在出口
13 ，开始部署，可以选择出口方式。

PP0E，公网等。

这里选择是公网固定地址
13、配置完成wan,
14、配置lan口属性
15、连接安全云，保持默认
16、核对配置
17、将刚刚配置WAN口，lan口加入安全域，先选择网络-安全域。

18、点击untrust 安全域加wan口加入到untrust内
19、将lan加入trust安全域内。

20、最后在安全策略内，将相关策略放行即可。

21、放行trust 到untrust策略。

H3C SecPath F100-C-SI防火墙 Web配置指导-5PW100-安全配置

目录1访问控制 ············································································································································ 1-11.1 概述 ··················································································································································· 1-11.2 配置访问控制····································································································································· 1-11.3 访问控制典型配置举例 ······················································································································ 1-3 2网站过滤 ············································································································································ 2-12.1 概述 ··················································································································································· 2-12.2 网站过滤典型配置举例 ······················································································································ 2-23 MAC地址过滤 ···································································································································· 3-13.1 概述 ··················································································································································· 3-13.2 配置MAC地址过滤····························································································································· 3-13.2.1 配置MAC地址过滤类型··········································································································· 3-13.2.2 配置要过滤的MAC地址··········································································································· 3-23.3 MAC地址过滤典型配置举例 ·············································································································· 3-3 4攻击防范 ············································································································································ 4-14.1 概述 ··················································································································································· 4-14.1.1 黑名单功能······························································································································ 4-14.1.2 入侵检测功能 ·························································································································· 4-14.2 配置黑名单 ········································································································································ 4-34.2.1 配置概述 ································································································································· 4-34.2.2 启用黑名单过滤功能 ··············································································································· 4-44.2.3 手动新建黑名单表项 ··············································································································· 4-44.2.4 查看黑名单······························································································································ 4-54.3 配置入侵检测····································································································································· 4-54.4 攻击防范典型配置举例 ······················································································································ 4-64.4.1 攻击防范典型配置举例 ··········································································································· 4-6 5应用控制 ············································································································································ 5-15.1 概述 ··················································································································································· 5-15.2 配置应用控制····································································································································· 5-15.2.1 配置概述 ································································································································· 5-15.2.2 加载应用程序 ·························································································································· 5-15.2.3 配置自定义应用程序 ··············································································································· 5-25.2.4 使能应用控制 ·························································································································· 5-35.3 应用控制典型配置举例 ······················································································································ 5-41 访问控制1.1 概述访问控制是指通过设置时间段、局域网内计算机的IP地址、端口范围和数据包协议类型，禁止符合指定条件的数据包通过，来限制局域网内的计算机对Internet的访问。

H3C SecPath防火墙系列产品混合模式的典型配置

H3C SecPath防火墙系列产品混合模式的典型配置
一、组网需求：
组网图中需要三台PC, PC1和PC4在Trust区域；PC2处于DMZ区域，其IP地址与PC1和PC4在同一网段，PC3位于Untrust区域，为外部网络。

G0/0接口和G1/0接口属于同一个桥组Bridge1。

对于访问控制有如下要求：
在防火墙G0/1接口上配置NAT，使Trust区域与DMZ区域通过地址转换才能访问Untrust区域；
通过NAT Server使DMZ区域对Untrust区域提供WWW服务；
在G1/0接口绑定ASPF策略并配合包过滤，使得Trust区域用户可以访问DMZ区域设备；但DMZ区域不能访问Trust区域；
在G0/0接口上绑定基于MAC地址的访问控制列表禁止PC4访问其他任何区域。

二、组网图：
支持混合模式的产品型号有：Secpath F1000-A/F1000-S/F100-E/F100-A；版本要求Comware software, Version 3.40, ESS 1622及以后。

四、配置关键点：
1、每一个桥组都是独立的，报文不可能在分属不同桥组的端口之间
传输。

换句话说，从一个桥组端口接收到的报文，只能从相同桥
组的其他端口发送出去。

防火墙上的一个接口不能同时加入两个
或两个以上的桥组。

2、要实现不同桥组之间或二层接口和三层接口之间数据转发，需要
创建桥组虚接口，并且将桥组虚接口加入到相应的区域。

H3C SecPath F100系列防火墙配置教程

H3C SecPath F100系列防火墙配置教程初始化配置〈H3C〉system-view开启防火墙功能[H3C]firewall packet-filter enable[H3C]firewall packet-filter default permit分配端口区域[H3C] firewall zone untrust[H3C-zone-trust] add interface GigabitEthernet0/0[H3C] firewall zone trust[H3C-zone-trust] add interface GigabitEthernet0/1工作模式firewall mode transparent 透明传输firewall mode route 路由模式http 服务器使能HTTP 服务器 undo ip http shutdown关闭HTTP 服务器 ip http shutdown添加WEB用户[H3C] local-user admin[H3C-luser-admin] password simple admin[H3C-luser-admin] service-type telnet[H3C-luser-admin] level 3开启防范功能firewall defend all 打开所有防范切换为中文模式 language-mode chinese设置防火墙的名称 sysname sysname配置防火墙系统IP 地址 firewall system-ip system-ip-address [ address-mask ] 设置标准时间 clock datetime time date设置所在的时区 clock timezone time-zone-name { add | minus } time取消时区设置 undo clock timezone配置切换用户级别的口令 super password [ level user-level ] { simple | cipher } password取消配置的口令 undo super password [ level user-level ]缺缺省情况下，若不指定级别，则设置的为切换到3 级的密码。

H3C SecPath Web 应用防火墙安全手册说明书

未经本公司书面许可，任何单位和个人不得擅自摘抄、复制本书内容的部分或全部，并不得以任何形式传播。

H3C 、、H3CS 、H3CIE 、H3CNE 、Aolynk 、、H 3Care 、、IRF 、NetPilot 、Netflow 、SecEngine 、SecPath 、SecCenter 、SecBlade 、Comware 、ITCMM 、HUASAN 、华三均为杭州华三通信技术有限公司的商标。

对于本手册中出现的其它公司的商标、产品标识及商品名称，由各自权利人拥有。

由于产品版本升级或其他原因，本手册内容有可能变更。

H3C 保留在没有任何通知或者提示的情况下对本手册的内容进行修改的权利。

本手册仅作为使用指导，H3C 尽全力在本手册中提供准确的信息，但是H3C 并不确保手册内容完全没有错误，本手册中的所有陈述、信息和建议也不构成任何明示或暗示的担保。

技术支持用户支持邮箱：***************技术支持热线电话：400-810-0504（手机、固话均可拨打）网址：资料获取方式您可以通过H3C 网站（）获取最新的产品资料：H3C 网站与产品资料相关的主要栏目介绍如下：•[服务支持/文档中心]：可以获取硬件安装类、软件升级类、配置类或维护类等产品资料。

•[产品技术]：可以获取产品介绍和技术介绍的文档，包括产品相关介绍、技术介绍、技术白皮书等。

•[解决方案]：可以获取解决方案类资料。

• [服务支持/软件下载]：可以获取与软件版本配套的资料。

资料意见反馈如果您在使用过程中发现产品资料的任何问题，可以通过以下方式反馈：E-mail ：************感谢您的反馈，让我们做得更好！环境保护本产品符合关于环境保护方面的设计要求，产品的存放、使用和弃置应遵照相关国家法律、法规要求进行。

H3C-SecPath系列防火墙基本上网配置

新手可以根据下面的配置一步一步操作，仔细一点儿就没问题了~！可以用超级终端配置，也可以用CRT配置如果配置了，还是不能上网，可以加我的QQ：957602411恢复出厂设置：Reset saved-configuration配置防火墙缺省允许报文通过：system-viewfirewall packet-filter default permit为防火墙的以太网接口（以Ethernet0/0为例）配置IP位置，并将接口加入到安全区域：interface Ethernet0/0ip address IP位置子网掩码quitfirewall zone trustadd interface Ethernet0/0quit添加登录用户为使用户可以通过Web登录，并且有权限对防火墙进行管理，必须为用户添加登录帐户并且赋予其权限：local-user 登录账号password simple 登录密码service-type telnetlevel 3quitquitsysfirewall packet-filter default permitdialer-rule 1 ip permitacl number 3000rule 0 permit ipquitinterface Dialer1link-protocol pppppp chap user PPPOE账号ppp chap password simple PPPOE密码ip address ppp-negotiatedialer-group 1dialer bundle 1nat outbound 3000quitinterface Ethernet0/4pppoe-client dial-bundle-number 1firewall zone untrustadd interface Ethernet0/4add interface Dialer1quitfirewall zone trustadd interface Ethernet0/0quitip route-static 0.0.0.0 0.0.0.0 Dialer 1 preference 60save友情提示：部分文档来自网络整理，供您参考！文档可复制、编辑，期待您的好评与关注！。

HCSecath F系列防火墙配置教程

H3C S e c P a t h F100系列防火墙配置教程初始化配置〈H3C〉system-view开启防火墙功能[H3C]firewall packet-filter enable[H3C]firewall packet-filter default permit分配端口区域[H3C] firewall zone untrust[H3C-zone-trust] add interface GigabitEthernet0/0[H3C] firewall zone trust[H3C-zone-trust] add interface GigabitEthernet0/1工作模式firewall mode transparent 透明传输firewall mode route 路由模式http 服务器使能HTTP 服务器 undo ip http shutdown关闭HTTP 服务器 ip http shutdown添加WEB用户[H3C] local-user admin[H3C-luser-admin] service-type telnet[H3C-luser-admin] level 3开启防范功能firewall defend all 打开所有防范切换为中文模式 language-mode chinese设置防火墙的名称 sysname sysname配置防火墙系统IP 地址 firewall system-ip system-ip-address [ address-mask ]设置标准时间 clock datetime time date设置所在的时区 clock timezone time-zone-name { add | minus } time取消时区设置 undo clock timezone配置切换用户级别的口令 super password [ level user-level ] { simple | cipher } password取消配置的口令 undo super password [ level user-level ]缺缺省情况下，若不指定级别，则设置的为切换到3 级的密码。

H3C SecPath F100系列防火墙配置

H3C SecPath F100系列防火墙配置2009-10-13 16:52:34标签：H3C防火墙配置初始化配置〈H3C〉system-view开启防火墙功能[H3C]firewall packet-filter enable[H3C]firewall packet-filter default permit分配端口区域[H3C] firewall zone untrust[H3C-zone-trust] add interface GigabitEthernet0/0[H3C] firewall zone trust[H3C-zone-trust] add interface GigabitEthernet0/1工作模式firewall mode transparent 透明传输firewall mode route 路由模式http 服务器使能HTTP 服务器 undo ip http shutdown关闭HTTP 服务器 ip http shutdown添加WEB用户[H3C] local-user admin[H3C-luser-admin] password simple admin[H3C-luser-admin] service-type telnet[H3C-luser-admin] level 3开启防范功能firewall defend all 打开所有防范切换为中文模式 language-mode chinese设置防火墙的名称 sysname sysname配置防火墙系统IP 地址 firewall system-ip system-ip-address [ address-mask ]设置标准时间 clock datetime time date设置所在的时区 clock timezone time-zone-name { add | minus } time取消时区设置 undo clock timezone配置切换用户级别的口令 super password [ level user-level ] { simple | cipher } password取消配置的口令 undo super password [ level user-level ]缺缺省情况下，若不指定级别，则设置的为切换到3 级的密码。

H C SecPath F 系列防火墙配置教程

H3C SecPath F100系列防火墙配置教程初始化配置〈H3C〉system-view开启防火墙功能[H3C]firewall packet-filter enable[H3C]firewall packet-filter default permit分配端口区域[H3C] firewall zone untrust[H3C-zone-trust] add interface GigabitEthernet0/0 [H3C] firewall zone trust[H3C-zone-trust] add interface GigabitEthernet0/1 工作模式firewall mode transparent 透明传输firewall mode route 路由模式http 服务器使能HTTP 服务器 undo ip http shutdown关闭HTTP 服务器 ip http shutdown添加WEB用户[H3C] local-user admin[H3C-luser-admin] password simple admin[H3C-luser-admin] service-type telnet[H3C-luser-admin] level 3开启防范功能firewall defend all 打开所有防范切换为中文模式 language-mode chinese设置防火墙的名称 sysname sysname配置防火墙系统IP 地址 firewall system-ip system-ip-address[ address-mask ]设置标准时间 clock datetime time date设置所在的时区 clock timezone time-zone-name { add | minus } time 取消时区设置 undo clock timezone配置切换用户级别的口令 super password [ level user-level ] { simple | cipher }password取消配置的口令 undo super password [ level user-level ]缺缺省情况下，若不指定级别，则设置的为切换到3 级的密码。

H C SecPath F C EI 防火墙说明书

目录第1章产品介绍...............................................................................1-11.1 简介....................................................................................1-11.2 外观....................................................................................1-21.2.1 前面板......................................................................1-21.2.2 后面板......................................................................1-21.3 规格....................................................................................1-31.4 指示灯................................................................................1-31.5 固定接口.............................................................................1-41.5.1 配置口......................................................................1-41.5.2 以太网口..................................................................1-5第2章安装前准备工作....................................................................2-12.1 安装场所要求......................................................................2-12.1.1 温度/湿度要求..........................................................2-12.1.2 洁净度要求...............................................................2-12.1.3 防静电要求...............................................................2-22.1.4 电磁环境要求...........................................................2-42.1.5 防雷击要求...............................................................2-42.1.6 检查安装台...............................................................2-52.1.7 机柜安装要求...........................................................2-52.2 安全注意事项......................................................................2-52.2.1 安全标志..................................................................2-52.2.2 通用安全建议...........................................................2-62.2.3 用电安全..................................................................2-62.3 安装工具、仪表和设备.......................................................2-6第3章防火墙的安装.......................................................................3-13.1 防火墙安装流程..................................................................3-13.2 安装防火墙到指定位置.......................................................3-13.2.1 安装防火墙到工作台................................................3-23.2.2 安装防火墙到机柜....................................................3-23.3 连接保护地线......................................................................3-43.4 连接电源线.........................................................................3-53.5 连接接口电缆......................................................................3-73.5.1 连接配置口电缆.......................................................3-73.5.2 连接以太网电缆.......................................................3-83.6 安装后的检查......................................................................3-8第4章防火墙的启动与配置............................................................4-14.1 搭建配置环境......................................................................4-14.1.1 连接防火墙到配置终端............................................4-14.1.2 设置配置终端的参数................................................4-14.2 防火墙上电.........................................................................4-44.2.1 上电前检查...............................................................4-44.2.2 防火墙上电...............................................................4-54.2.3 上电后检查/操作......................................................4-54.3 启动过程.............................................................................4-54.4 防火墙配置的基本思路.......................................................4-64.5 命令行接口.........................................................................4-74.5.1 命令行接口的特点....................................................4-74.5.2 命令行接口...............................................................4-7第5章防火墙的软件维护................................................................5-15.1 Boot菜单.............................................................................5-15.1.1 防火墙的Boot菜单....................................................5-25.1.2 防火墙的Boot ROM子菜单......................................5-35.2 利用XModem协议完成应用程序和Boot ROM程序升级.........5-45.2.1 应用程序的升级.......................................................5-45.2.2 Boot ROM程序的升级..............................................5-75.2.3 Boot ROM程序扩展段的升级...................................5-85.3 通过TFTP完成应用程序的升级..........................................5-85.4 利用FTP完成程序/文件的上传下载..................................5-125.5 应用程序及配置文件的维护..............................................5-165.5.1 显示所有文件.........................................................5-165.5.2 删除文件................................................................5-175.6 Boot ROM程序扩展段的备份及恢复.................................5-185.6.1 在FLASH中备份Boot ROM程序的扩展段..............5-185.6.2 从FLASH中恢复Boot ROM程序扩展段..................5-185.7 口令丢失的处理................................................................5-195.7.1 用户口令丢失.........................................................5-195.7.2 Boot ROM口令丢失...............................................5-20第6章安装故障处理.......................................................................6-16.1 电源系统问题故障处理.......................................................6-16.2 配置系统故障处理..............................................................6-1插图目录图1-1 F100-C-EI防火墙前面板.................................................1-2图1-2 F100-C-EI防火墙后面板.................................................1-2图1-3 配置口电缆示意图..........................................................1-5图1-4 以太网电缆示意图..........................................................1-6图2-1 佩戴防静电手腕示意图...................................................2-4图3-1 防火墙安装流程..............................................................3-1图3-2 挂耳结构图.....................................................................3-2图3-3 安装左、右前挂耳到防火墙的两侧.................................3-3图3-4 固定防火墙到机架..........................................................3-3图3-5 连接保护地接地端子到防火墙........................................3-4图3-6 连接保护地线到接地排...................................................3-5图3-7 连接交流电源线..............................................................3-6图3-8 连接配置口电缆..............................................................3-7图4-1 新建连接........................................................................4-1图4-2 本地配置连接端口设置...................................................4-2图4-3 串口参数设置.................................................................4-2图4-4 超级终端窗口.................................................................4-3图4-5 终端类型设置.................................................................4-4图5-1 断开终端连接.................................................................5-5图5-2 修改波特率.....................................................................5-5图5-3 [发送文件]对话框............................................................5-6图5-4 正在发送文件界面..........................................................5-6图5-5 搭建TFTP升级环境........................................................5-9图5-6 搭建FTP升级环境........................................................5-12表格目录表1-1 F100-C-EI防火墙规格....................................................1-3表1-2 F100-C-EI指示灯含义....................................................1-3表1-3 配置口属性.....................................................................1-4表1-4 以太网口属性.................................................................1-5表2-1 机房温度/湿度要求.........................................................2-1表2-2 机房灰尘含量限值..........................................................2-2表2-3 机房有害气体限值..........................................................2-2第1章产品介绍1.1 简介H3C SecPath F100-C-EI防火墙设备（以下简称F100-C-EI）是H3C公司面向家庭办公、小型办公室（Small Office Home Office，SOHO）开发的新一代专业防火墙产品。

H C SecPath F C EI 防火墙说明书

目录第1章产品介绍...............................................................................1-11.1 简介....................................................................................1-11.2 外观....................................................................................1-21.2.1 前面板......................................................................1-21.2.2 后面板......................................................................1-21.3 规格....................................................................................1-31.4 指示灯................................................................................1-31.5 固定接口.............................................................................1-41.5.1 配置口......................................................................1-41.5.2 以太网口..................................................................1-5第2章安装前准备工作....................................................................2-12.1 安装场所要求......................................................................2-12.1.1 温度/湿度要求..........................................................2-12.1.2 洁净度要求...............................................................2-12.1.3 防静电要求...............................................................2-22.1.4 电磁环境要求...........................................................2-42.1.5 防雷击要求...............................................................2-42.1.6 检查安装台...............................................................2-52.1.7 机柜安装要求...........................................................2-52.2 安全注意事项......................................................................2-52.2.1 安全标志..................................................................2-52.2.2 通用安全建议...........................................................2-62.2.3 用电安全..................................................................2-62.3 安装工具、仪表和设备.......................................................2-6第3章防火墙的安装.......................................................................3-13.1 防火墙安装流程..................................................................3-13.2 安装防火墙到指定位置.......................................................3-13.2.1 安装防火墙到工作台................................................3-23.2.2 安装防火墙到机柜....................................................3-23.3 连接保护地线......................................................................3-43.4 连接电源线.........................................................................3-53.5 连接接口电缆......................................................................3-73.5.1 连接配置口电缆.......................................................3-73.5.2 连接以太网电缆.......................................................3-83.6 安装后的检查......................................................................3-8第4章防火墙的启动与配置............................................................4-14.1 搭建配置环境......................................................................4-14.1.1 连接防火墙到配置终端............................................4-14.1.2 设置配置终端的参数................................................4-14.2 防火墙上电.........................................................................4-44.2.1 上电前检查...............................................................4-44.2.2 防火墙上电...............................................................4-54.2.3 上电后检查/操作......................................................4-54.3 启动过程.............................................................................4-54.4 防火墙配置的基本思路.......................................................4-64.5 命令行接口.........................................................................4-74.5.1 命令行接口的特点....................................................4-74.5.2 命令行接口...............................................................4-7第5章防火墙的软件维护................................................................5-15.1 Boot菜单.............................................................................5-15.1.1 防火墙的Boot菜单....................................................5-25.1.2 防火墙的Boot ROM子菜单......................................5-35.2 利用XModem协议完成应用程序和Boot ROM程序升级.........5-45.2.1 应用程序的升级.......................................................5-45.2.2 Boot ROM程序的升级..............................................5-75.2.3 Boot ROM程序扩展段的升级...................................5-85.3 通过TFTP完成应用程序的升级..........................................5-85.4 利用FTP完成程序/文件的上传下载..................................5-125.5 应用程序及配置文件的维护..............................................5-165.5.1 显示所有文件.........................................................5-165.5.2 删除文件................................................................5-175.6 Boot ROM程序扩展段的备份及恢复.................................5-185.6.1 在FLASH中备份Boot ROM程序的扩展段..............5-185.6.2 从FLASH中恢复Boot ROM程序扩展段..................5-185.7 口令丢失的处理................................................................5-195.7.1 用户口令丢失.........................................................5-195.7.2 Boot ROM口令丢失...............................................5-20第6章安装故障处理.......................................................................6-16.1 电源系统问题故障处理.......................................................6-16.2 配置系统故障处理..............................................................6-1插图目录图1-1 F100-C-EI防火墙前面板.................................................1-2图1-2 F100-C-EI防火墙后面板.................................................1-2图1-3 配置口电缆示意图..........................................................1-5图1-4 以太网电缆示意图..........................................................1-6图2-1 佩戴防静电手腕示意图...................................................2-4图3-1 防火墙安装流程..............................................................3-1图3-2 挂耳结构图.....................................................................3-2图3-3 安装左、右前挂耳到防火墙的两侧.................................3-3图3-4 固定防火墙到机架..........................................................3-3图3-5 连接保护地接地端子到防火墙........................................3-4图3-6 连接保护地线到接地排...................................................3-5图3-7 连接交流电源线..............................................................3-6图3-8 连接配置口电缆..............................................................3-7图4-1 新建连接........................................................................4-1图4-2 本地配置连接端口设置...................................................4-2图4-3 串口参数设置.................................................................4-2图4-4 超级终端窗口.................................................................4-3图4-5 终端类型设置.................................................................4-4图5-1 断开终端连接.................................................................5-5图5-2 修改波特率.....................................................................5-5图5-3 [发送文件]对话框............................................................5-6图5-4 正在发送文件界面..........................................................5-6图5-5 搭建TFTP升级环境........................................................5-9图5-6 搭建FTP升级环境........................................................5-12表格目录表1-1 F100-C-EI防火墙规格....................................................1-3表1-2 F100-C-EI指示灯含义....................................................1-3表1-3 配置口属性.....................................................................1-4表1-4 以太网口属性.................................................................1-5表2-1 机房温度/湿度要求.........................................................2-1表2-2 机房灰尘含量限值..........................................................2-2表2-3 机房有害气体限值..........................................................2-2第1章产品介绍1.1 简介H3C SecPath F100-C-EI防火墙设备（以下简称F100-C-EI）是H3C公司面向家庭办公、小型办公室（Small Office Home Office，SOHO）开发的新一代专业防火墙产品。

HCSecPathF系列防火墙配置教程

H3C SecPath F100系列防火墙配置教程初始化配置〈H3C〉system-view开启防火墙功能[H3C]firewall packet-filter enable[H3C]firewall packet-filter default permit分配端口区域[H3C] firewall zone untrust[H3C-zone-trust] add interface GigabitEthernet0/0 [H3C] firewall zone trust[H3C-zone-trust] add interface GigabitEthernet0/1 工作模式firewall mode transparent 透明传输firewall mode route 路由模式http 服务器使能HTTP 服务器 undo ip http shutdown关闭HTTP 服务器 ip http shutdown添加WEB用户[H3C] local-user admin[H3C-luser-admin] password simple admin[H3C-luser-admin] service-type telnet[H3C-luser-admin] level 3开启防范功能firewall defend all 打开所有防范切换为中文模式 language-mode chinese设置防火墙的名称 sysname sysname配置防火墙系统IP 地址 firewall system-ip system-ip-address[ address-mask ]设置标准时间 clock datetime time date设置所在的时区 clock timezone time-zone-name { add | minus } time 取消时区设置 undo clock timezone配置切换用户级别的口令 super password [ level user-level ] { simple | cipher }password取消配置的口令 undo super password [ level user-level ]缺缺省情况下，若不指定级别，则设置的为切换到3 级的密码。

配置H3C SecPath f100-c防火墙纪实

配置H3C SecPath f100-c防火墙纪实
有人请我去给设置上网，免费的奥，本人很好的，乐于助人呢。

本来以为是个四口的小路由，三分钟就可以了，没有想到我错了，去了一看好大一个防火墙，而且要使用console口进行初始配置，一下子命令都忘干净了。

我灰溜溜的回去查资料了，打个电话找找专家，拨开乌云见太阳了。

原来如此简单，只因自己平时用工不到，学习不精所致。

拿到一手配置材料，高高兴兴就去了，自信是做事的根本。

给他们精彩的上了一堂课，围观者都瞪大了眼睛，说是英文的不懂。

让我快点，不要耽误工作了。

哎，没有懂得人，只有我自己孤芳自赏了。

下面给我大家分享一下，f100的adsl拨号共享上网的具体配置文件，和网络连接图解如图1,很多还是很有参考价值的，尤其争对那些初级的网络爱好者，大家一起学习进步。

希望大家有什么高超的建议和意见都跟帖，我会认真细致的进行分析处理。

我也做个榜样，把每天生活中重要的事件记录下来，供所有爱好网络技术，爱好学习的朋友一个参考。

学无止境。

h3c防火墙怎么样设置好呢

h3c防火墙怎么样设置好呢h3c防火墙怎么样设置好呢h3c防火墙要怎么样设置才最好呢?小编来教你方法!下面由店铺给你做出详细的h3c防火墙设置方法介绍!希望对你有帮助!h3c防火墙设置方法一：配置HTTP服务器使能HTTP服务器SecPath系列安全产品支持以HTTP方式登录到系统中，并通过Web管理界面对系统进行配置和管理。

在使用Web界面登录到系统前，必须先使能HTTP服务器功能。

请在系统视图下进行下列配置。

使能/关闭HTTP服务器使能HTTP服务器undo ip http shutdown关闭HTTP服务器ip http shutdown缺省情况下，系统使能HTTP服务器。

仅当登录用户具有T elnet的服务类型时(service-type telnet)，才允许登录HTTP服务器，且不同等级的用户在Web界面中的可配置项也会不同。

h3c防火墙设置方法二：不需要把网段分开，除非你的IP不够用因此，按你的要求，3个部分，只需要分3个IP段就可以，例如：行政部：100-139，财务部：140-179，业务部：180-119，并在防火墙设置分组上网权限在防火墙上绑定每部电脑的网卡MAC和IP，再给每个组设置规则h3c防火墙设置方法三：首先得确定内网里有到服务器外网地址的路由，还有服务器到内网地址的路由。

如果有路由直接在WEB界面里选防火墙----域间关系，加上一条原域服务器B所在的域目的域内网域源IP 服务器Bip 目的IP 内网IP 端口允许通过的端口动作permit 然后使能，加一条原域内网域到服务器 B 所在域 permit 的就可以了相关阅读：h3c软件介绍秉承“融合、智能、开放”的IT管理理念，华三通信推出基于iMC智能管理中心统一平台的全系列产品和解决方案，为客户提供端到端的管理业务流程，实现了业务、资源和用户的深度融合管理，使客户真正做到了“精细IT、智能掌控”。

作为H3C NGIP战略的重要组成部分，华三通信业务软件产品依托开放架构，以业务为导向，实现智能融合和协同联动，将各个业务模块进行端到端整合，提供端到端的精细化业务管理：数据中心管理领域，提供一体化、可视化的基础设施管理，虚拟化、自动化的资源管理，多纬度、新模型的应用和流量管理，规范化、可衡量的IT运维流程管理，为数据中心资源的动态调配、最优化利用提供了保障;基础承载网络管理领域，提供从分级分权的基础资源管理，全面、易部署的终端准入控制，端到端的业务部署，可视化的流量性能优化以及可灵活定义的业务报表展示，确保基础承载网络的高效、可靠。

H3C SecPath防火墙配置指导

目录1路由设置 ············································································································································ 1-11.1 概述 ··················································································································································· 1-11.2 配置静态路由····································································································································· 1-11.3 查看激活路由表 ································································································································· 1-21.4 静态路由典型配置举例 ······················································································································ 1-31.5 注意事项············································································································································ 1-61 路由设置•本章所指的路由器代表了一般意义下的路由器，以及运行了路由协议的三层交换机。

HCF防火墙配置

连接好电脑到-防火墙(de)console线,打开putty（默认账户和密码admin,admin）进入特权模式,命令：system-view建立管理员账号,并设置密码：manageDevicemanagementuser（管理用户）建立管理账户没设超级密码情况下开启HTTPS服务设立超级密码.类似cisco(de)特权密码登录验证在全局模式下.输入命令：superlevel-进入特权模式,输入设置好(de)特权密码,密码隐藏开启h3c防火墙HTTPS服务打开WEB界面,输入IP,登录防火墙,如图选择设备-管理员返回到xshell界面,保存配置,命令：save进接口配置IP.命令与Cisco没多大出入（全局下）查看接口(de)配置,命令如下；g1/0/0接口默认(de)配置,为了方便使用暂留不动,以及VRRP(de)配置.portlink-moderoute类似Cisco(de)iprouting(三层)进入到H3C防火墙(de)区域,命令如下把对应(de)接口划分到对应(de)区域,命令如下dissecurity-zone查看安全域状态信息默认路由做NAT1.先抓取需要IP地址转换(de)IP段(de)流量,做ACL2.建立动态地址池.3.动态NAT(de)应用与IP地址(de)转换,命令如下：discurrent-configurationinterfaceg1/0/1查看g1/0/1(de)状况信息建立一条新(de)拓展ACL,放行IP流量,用于安全区域(de)跨区域(de)访问应用,命令如下：创建源区域到目(de)区域过滤包3500diszone-pairsecurity,查看所有区域(de)对应关系状态security-zoneintra-zonedefaultpermit（缺省是允许流量从trust口到untrust口方向(de)主动访问,而不允许untrust口到trust口方向(de)主动访问.当从trust口到untrust口有主动访问时,防火墙会保存这个连接信息,回应数据从untrust口到trust方向,防火墙会放行,但是不会允许untrust口到trust口(de)主动访问）命令用来配置同一安全域内接口间报文处理(de)缺省动作为permit. acladvancednameh3crule5permiticmpsource（放行icmp）做VRRP.步骤如下把需要做VRRP(de)接口设置为bridge（桥接模式）然后把接口设置为trunkdiscurrent-configurationinterfaceg1/0/3配置VRRP,(在接口下)然后在另外一台防火墙相应(de)接口进行相应(de)设置.只是优先值设置为100（H3C默认也是100）disvrrp查看VRRP状态（当主,down,备用自动抢占）测试配置VTY,并启用本地账户配置输入模式虚墙建立一个名为cisco(de)虚墙设置磁盘(de)使用上限设置内存(de)使用上限设置cpu(de)权重分配接口给cisco这个虚墙,确认回车Y启动虚墙查询登录虚墙cisco,可进行配置,命令;switchtocontext。

设置hcsecpathf系列防火墙的web访问终审稿)

设置H3C SecPath F100 系列防火墙的web访问

H3C SecPath F100系列防火墙配置教程

web配置H3C防火墙

H3C SecPath F100-C-SI防火墙 Web配置指导-5PW100-安全配置

H3C SecPath防火墙系列产品混合模式的典型配置

H3C SecPath F100系列防火墙配置教程

H3C SecPath Web 应用防火墙 安全手册说明书

H3C-SecPath系列防火墙基本上网配置

HCSecath F系列防火墙配置教程

H3C SecPath F100系列防火墙配置

H C SecPath F 系列防火墙配置教程

H C SecPath F C EI 防火墙说明书

H C SecPath F C EI 防火墙说明书

HCSecPathF系列防火墙配置教程

配置H3C SecPath f100-c防火墙纪实

h3c防火墙怎么样设置好呢

H3C SecPath防火墙配置指导

HCF防火墙配置

H3C SecPath Web 应用防火墙安全手册说明书