A5_GBL6s_OP_Wk2_IntroDFSS - V1.3 2007-10-05
25AA256-ISN;25LC256-ISN;25LC256-ISM;25AA256-IP;25LC256-IP;中文规格书,Datasheet资料
Pin Function Table
Name
Function
CS SO WP VSS SI SCK HOLD VCC
Chip Select Input Serial Data Output Write-Protect Ground Serial Data Input Serial Clock Input Hold Input Supply Voltage
• Built-In Write Protection:
- Power-on/off data protection circuitry
- Write enable latch
- Write-protect pin
• Sequential Read
• High Reliability:
- Endurance: 1,000,000 erase/write cycles
© 2007 Microchip Technology Inc.
/
DS21822F-page 1
25AA256/25LC256
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings (†)
VCC.............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V Storage temperature .................................................................................................................................-65°C to 150°C Ambient temperature under bias ...............................................................................................................-40°C to 125°C ESD protection on all pins ..........................................................................................................................................4 kV
ProductTypeList-optiMOS(20-250V)
N-Channel MOSFETs: OptiMOS™ (20V…250V) Product TypeProduct TypeBSN045NE2LSBSN011NE2LSBSN011NE2LSIBSN012N03LSBSN012N03LSIBSN048N03LSBSB012NE2LXBSB014N04LX3 GBSB015N04NX3 GBSB017N03LX3 GBSB012N03LX3 GBSB028N06NN3 GBSB044N08NN3 GBSB056N10NN3 GBSB013NE2LXIBSB008NE2LXBSB280N15NZ3 G BSB165N15NZ3 G BSB012NE2LXI BSF024N03LT3 G BSF050N03LQ3 G BSF030NE2LQ BSF134N10NJ3 G BSF110N06NT3 G BSF450NE7NH3 G BSF035NE2LQ IPB015N04L G IPB027N10N3 G IPB035N08N3 G IPB015N04N G IPB019N06L3 G IPB083N10N3 G IPB042N10N3 G IPB054N06N3 GIPB037N06N3 G IPB097N08N3 G IPB055N03L G IPB054N08N3 G IPB042N03L G IPB022N04L G IPB065N03L G IPB072N15N3 G IPB025N08N3 G IPB080N03L G IPB081N06L3 G IPB147N03L G IPB096N03L G IPB136N08N3 GIPB090N06N3 G IPB029N06N3 G IPB049NE7N3 G IPB031NE7N3 G IPB020NE7N3 G IPB123N10N3 G IPB038N12N3 G IPB144N12N3 G IPB320N20N3 G IPB107N20N3 G IPB200N25N3 G IPB600N25N3 G BUZ32 H3045A BUZ31 H3045A IPB108N15N3 G BUZ30A H3045AIPB107N20NA IPB057N06N IPB026N06N IPB230N06L3 G IPB067N08N3 G IPB034N03L G IPB009N03L G IPB011N04L G IPB011N04N G IPB016N06L3 G IPB017N06N3 G IPB019N08N3 G IPB020N04N G IPB025N10N3 G IPB030N08N3 GIPB036N12N3 G IPB065N15N3 G IPB010N06NIPB014N06NSPD07N20 GIPD031N06L3 G IPD034N06N3 G IPD035N06L3 G IPD036N04L GIPD038N06N3 G IPD048N06L3 G IPD053N08N3 G SPD50N03S2L-06 G SPD30N03S2L-07 G IPD068N10N3 G SPD50N03S2-07 GIPD082N10N3 G IPD088N06N3 G IPD096N08N3 G SPD30N03S2L-10 G IPD127N06L GIPD135N08N3 G IPD160N04L GIPD170N04N GIPD200N15N3 G SPD30N03S2L-20 G IPD220N06L3 G IPD25CN10N GIPD250N06N3 G IPD33CN10N GIPD350N06L GIPD640N06L G IPD78CN10N G IPD800N06N G IPD122N10N3 G IPD180N10N3 G IPD110N12N3 G IPD031N03L G IPD040N03L G IPD050N03L G IPD060N03L G IPD075N03L G IPD090N03L G IPD320N20N3 G IPD600N25N3 G IPD530N15N3 G IPD105N03L G IPD135N03L GIPD025N06N IPD053N06N IPI023NE7N3 G IPI034NE7N3 G IPI052NE7N3 G IPI126N10N3 G IPI180N10N3 G IPI041N12N3 G IPI076N12N3 G IPI147N12N3 G IPI045N10N3 G IPI086N10N3 G IPI030N10N3 G IPI04CN10N G IPI072N10N3 G IPI26CN10N G IPI35CN10N GIPI075N15N3 G IPI200N15N3 G IPI024N06N3 G IPI032N06N3 G IPI040N06N3 G IPI037N08N3 G IPI320N20N3 G IPI110N20N3 G IPI200N25N3 G IPI600N25N3 G IPI111N15N3 G IPI530N15N3 G IPI020N06NIPI029N06N BUZ31 H3046 IPI084N06L3 GIPU135N08N3 G IPS110N12N3 G IPS060N03L G IPS075N03L G IPS031N03L G IPS040N03L G IPS090N03L G IPS105N03L G IPS135N03L G IPS050N03L G BSZ0908ND BSZ0907ND BSC0921NDI BSC0923NDI BSC0924NDI BSC0925ND BSC0910NDI BSC0911NDBSZ035N03LS G BSZ035N03MS G BSZ040N04LS G BSZ042N04NS G BSZ050N03LS G BSZ050N03MS G BSZ058N03LS G BSZ058N03MS G BSZ067N06LS3 G BSZ076N06NS3 G BSZ088N03MS G BSZ088N03LS G BSZ097N04LS G BSZ100N06LS3 G BSZ100N03MS GBSZ105N04NS G BSZ110N06NS3 G BSZ123N08NS3 G BSZ130N03MS G BSZ130N03LS G BSZ165N04NS G BSZ340N08NS3 G BSZ440N10NS3 G BSZ160N10NS3 G BSZ900N15NS3 G BSZ520N15NS3 G BSZ0909NSBSZ240N12NS3 G BSZ12DN20NS3 G BSZ16DN25NS3 GBSZ42DN25NS3 G BSZ900N20NS3 G BSZ060NE2LS BSZ065N03LS BSZ036NE2LS BSZ018NE2LS BSZ0901NSBSZ0901NSIBSZ0902NSBSZ0904NSIBSZ0902NSIBSZ018NE2LSI BSZ042N06NS BSZ023N04LS BSZ150N10LS3 G BSO615N GBSO033N03MS GBSO083N03MS G BSO110N03MS G BSO330N02K G BSO150N03MD G BSO220N03MD G BSC010NE2LS BSC050NE2LS BSC046N02KS G BSC019N02KS G BSC014N03LS G BSC016N03LS G BSC014N03MS G BSC016N04LS G BSC016N03MS G BSC017N04NS G BSC018N04LS GBSC020N03MS G BSC020N03LS G BSC025N03MS G BSC027N04LS G BSC025N03LS G BSC028N06LS3 G BSC030N03MS G BSC030N04NS G BSC030N03LS G BSC031N06NS3 G BSC034N03LS G BSC035N04LS G BSC042N03MS G BSC042N03LS GBSC050N03MS G BSC050N04LS G BSC050N03LS G BSC054N04NS G BSC057N03MS G BSC057N03LS G BSC057N08NS3 G BSC059N04LS G BSC060N10NS3 G BSC067N06LS3 G BSC076N06NS3 G BSC079N10NS GBSC080N03LS G BSC082N10LS G BSC090N03MS G BSC090N03LS G BSC093N04LS G BSC100N03MS G BSC100N10NSF G BSC100N06LS3 G BSC105N10LSF G BSC110N06NS3 G BSC118N10NS G BSC120N03MS G BSC120N03LS GBSC123N10LS G BSC152N10NSF G BSC190N15NS3 G BSC159N10LSF G BSC196N10NS G BSC205N10LS G BSC252N10NSF G BSC265N10LSF G BSC340N08NS3 G BSC042NE7NS3 G BSC160N10NS3 G BSC440N10NS3 G BSC077N12NS3 G BSC190N12NS3 G BSC520N15NS3 GBSC600N25NS3 G BSC026N02KS G BSC070N10NS3 G BSC109N10NS3 G BSC0909NSBSC360N15NS3 G BSC0908NSBSC240N12NS3 G BSC900N20NS3 G BSC12DN20NS3 G BSC16DN25NS3 G BSC22DN20NS3 G BSC018NE2LS BSC024NE2LS BSC011N03LS BSC052N03LSBSC0902NSBSC032NE2LS BSC0901NSIBSC0904NSIBSC010NE2LSI BSC0902NSIBSC014NE2LSI BSC018NE2LSI BSC011N03LSI BSC0906NSBSC009NE2LS BSC036NE7NS3 G BSC046N10NS3 G BSC028N06NS BSC010N04LSI BSC014N04LS BSC014N04LSIBSC039N06NS BSC014N06NS BSC010N04LS BSC500N20NS3 G BSC022N04LS BSC072N03LD G BSC150N03LD G BSC750N10ND G IPP023NE7N3 G IPP034NE7N3 G IPP052NE7N3 G BUZ31L HBUZ73 HBUZ73A HBUZ73AL HBUZ73L HIPP180N10N3 G IPP041N12N3 G IPP048N12N3 G IPP076N12N3 G IPP114N12N3 G IPP147N12N3 G IPP030N10N3 G IPP045N10N3 G IPP04CN10N G IPP05CN10N G IPP072N10N3 G IPP086N10N3 G IPP12CN10L G IPP16CN10N G IPP075N15N3 G IPP200N15N3 G IPP034N03L GIPP055N03L G IPP065N03L G IPP080N03L G IPP096N03L G IPP114N03L G IPP015N04N G IPP023N04N G IPP039N04L G IPP041N04N G IPP024N06N3 G IPP032N06N3 G IPP037N06L3 G IPP040N06N3 G IPP052N06L3 G IPP057N06N3 G IPP084N06L3 G IPP093N06N3 GIPP028N08N3 G IPP037N08N3 G IPP057N08N3 G IPP070N08N3 G IPP100N08N3 G IPP139N08N3 G IPP320N20N3 G IPP110N20N3 G IPP200N25N3 G IPP600N25N3 G BUZ31 HBUZ32 HIPP111N15N3 G BUZ30A HIPP065N04N G IPP530N15N3 GIPP048N04N G IPP110N20NA IPP147N03L G IPP029N06N IPP020N06N IPP040N06N IPP060N06N IPA028N08N3 G IPA037N08N3 G IPA057N08N3 G IPA100N08N3 G IPA045N10N3 G IPA086N10N3 G IPA126N10N3 G IPA180N10N3 G IPA030N10N3 GIPA105N15N3 G IPA032N06N3 G IPA057N06N3 G IPA093N06N3 G IPT004N03L IPT007N06N IPT020N10N3 IPT059N15N3Datasheet Group Product Status /dgdl/BSN045NE2LS_rev1.0.pdf?fBlade 3x3 (USON-6)in production olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433d68e984013d7ca959855780/dgdl/BSN011NE2LS_rev1.3.pdf?fBlade 3x3 (USON-6)in production olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433d68e984013d7cbfeef05815Blade 3x3 (USON-6)in production /dgdl/BSN011NE2LSI_rev1.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433d68e984013d7ccf22ee58e4Blade 3x3 (USON-6)in production /dgdl/BSN012N03LS_rev1.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433d68e984013d7cde510c594c/dgdl/BSN012N03LSI_rev1.3.pdf?Blade 3x3 (USON-6)in production folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433d68e984013d7cea5f8559f4Blade 3x3 (USON-6)in production /dgdl/BSN048N03LS_rev1.0.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433d68e984013d7cf6d2e25a60/dgdl/BSB012NE2LX_Rev+2.3.pdfCanPAK™ M-size in production?folderId=db3a304326dfb1300126fb3bec803f1a&fileId=db3a304326dfb1300126fb6a32613f3dCanPAK™ M-size in production /dgdl/BSB014N04LX3+G_Rev+2.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d590121a02c6c737a9bCanPAK™ M-size in production /dgdl/BSB015N04NX3+G_Rev+2.4.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d590121a03bbfcd7aacCanPAK™ M-size in production /dgdl/BSB017N03LX3+G_Rev+2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d590121a04b132c7abb/dgdl/BSB012N03LX3+G_Rev_+2CanPAK™ M-size in production.1_pdf.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d590121a0112ce07a8b/dgdl/BSB028N06NN3_G_rev2.0.CanPAK™ M-size in production pdf?folderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30432e25b009012e29fda4e23838/dgdl/BSB044N08NN3_G_rev2.0.CanPAK™ M-size in production pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30435819ae2e012e385cde7b70d4CanPAK™ M-size in production /dgdl/BSB056N10NN3+G_Rev+2.5.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30442e152e91012e390b9a631459/dgdl/BSB013NE2LXI_Rev+2.3.pdCanPAK™ M-size in production f?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432e398416012e47a158802577/dgdl/BSB008NE2LX_Rev+1.3.pdfCanPAK™ M-size in production?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432e564707012e5745ca7d000eCanPAK™ M-size in production /dgdl/BSB280N15NZ3+G+Rev+2.5_.pdf?folderId=db3a304326623792012669f6bee2224b&fileId=db3a30432e779412012e7b0b544c3852CanPAK™ M-size in production /dgdl/BSB165N15NZ3+G+Rev+2.2.pdf?folderId=db3a304326623792012669f6bee2224b&fileId=db3a30432e779412012e7b04a1353843/dgdl/BSB012NE2LXI_rev1+1.pdfCanPAK™ M-size coming soon?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433f764301013f805e3eb247c1CanPAK™ S-size in production /dgdl/BSF024N03LT3+G_Rev+2.1_pdf.pdf?folderId=db3a30431ddc9372011ebafa04517f8b&fileId=db3a30432239cccd012282adaadf7bc8CanPAK™ S-size in production /dgdl/BSF050N03LQ3+G_Rev+2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d590121a0f584407b1cCanPAK™ S-size in production /dgdl/BSF030NE2LQ_Rev+2.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432e398416012e47a8f0792588/dgdl/BSF134N10NJ3+G_Rev+2.5CanPAK™ S-size in production.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432e779412012e7afa4a6c3834CanPAK™ S-size in production /dgdl/BSF110N06NT3_G_rev2.0.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a3043382e837301387b92fdc80c37CanPAK™ S-size in production /dgdl/BSF450NE7NH3G_rev2.0.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433a047ba0013a687e2ae403daCanPAK™ S-size coming soon /dgdl/BSF035NE2LQ_rev1+1.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433f764301013f7fe8a925463cD2PAK (TO-263)in production /dgdl/IPB015N04L_rev1.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431936bc4b0119382488c359d3D2PAK (TO-263)in production /dgdl/IPB027N10N3+G_Rev2.4.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431ce5fb52011d1ed9348e15efD2PAK (TO-263)in production /dgdl/IPP037N08N3_Rev2.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431add1d95011ae8426111565bD2PAK (TO-263)in production /dgdl/IPB015N04N_rev2.2.pdf?folderId=db3a3043156fd5730115c7d50620107c&fileId=db3a30431689f4420116c474de8f0845/dgdl/IPB019N06L3_Rev2.2.pdf?fD2PAK (TO-263)in production olderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e2600a49e467b/dgdl/IPP086N10N3+G_Rev2.5.pdD2PAK (TO-263)in productionf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431ce5fb52011d1ac5c8fa1358/dgdl/IPP045N10N3+G_Rev2.5.pdD2PAK (TO-263)in productionf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431ce5fb52011d1e8b0cc31586D2PAK (TO-263)not for new design /dgdl/IPP_B057N06N3_Rev2.2.pdf?folderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e2b439f1d4d93/dgdl/IPP037N06L3_Rev2.7.pdf?fD2PAK (TO-263)in production olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431b3e89eb011b4561341f7d38D2PAK (TO-263)in production /dgdl/IPP040N06N3_Rev1.03.pdf?folderId=db3a3043163797a6011637c252b10018&fileId=db3a304317a7483601182c2d4f447647D2PAK (TO-263)in production /dgdl/IPP_I_B100N08N3_Rev2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431ddc9372011e071f53b82619D2PAK (TO-263)in production /dgdl/IPP055N03L_rev2.0.pdf?folderId=db3a30431441fb5d01148c401f250e27&fileId=db3a30431441fb5d01148d01ee1c0e91/dgdl/IPP057N08N3_Rev1.2.pdf?fD2PAK (TO-263)in production olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304317a748360117cf0cf5951d06/dgdl/IPP042N03L_rev2.0.pdf?foldD2PAK (TO-263)in production erId=db3a30431441fb5d01148c401f250e27&fileId=db3a30431441fb5d01148d012d010e8eD2PAK (TO-263)discontinued /dgdl/IPB022N04L_rev2.0.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431936bc4b01193836c99c5a08D2PAK (TO-263)in production /dgdl/IPP065N03L_rev2.0.pdf?folderId=db3a30431441fb5d01148c401f250e27&fileId=db3a30431441fb5d011492371ebc0fe2/dgdl/IPP075N15N3+G_Rev2.06.pD2PAK (TO-263)in production df?folderId=db3a304313b8b5a60113cee7c66a02d6&fileId=db3a304319c6f18c0119cd76cc527ab6/dgdl/IPB025N08N3_Rev1.2.pdf?fD2PAK (TO-263)in production olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304317a748360117d35658bc066bD2PAK (TO-263)in production /dgdl/IPP080N03L_rev2.0.pdf?folderId=db3a30431441fb5d01148c401f250e27&fileId=db3a30431441fb5d01148d028c300e94D2PAK (TO-263)in production /dgdl/IPP_B084N06L3_Rev2.23.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431b3e89eb011b4592273f7db2/dgdl/IPP147N03L_rev2.0.pdf?foldD2PAK (TO-263)in production erId=db3a30431441fb5d01148c401f250e27&fileId=db3a30431441fb5d01148d08f1f30e9aD2PAK (TO-263)in production /dgdl/IPP096N03L_rev2.0.pdf?folderId=db3a30431441fb5d01148c401f250e27&fileId=db3a30431441fb5d01148d0849910e97/dgdl/IPP139N08N3_Rev2.5.pdf?fD2PAK (TO-263)in production olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431add1d95011ae8a77e3656c2?folderId=db3a304313b8b5a60113cee7c66a02d6&fileId=db3a304319c6f18c0119cd1cc23279beD2PAK (TO-263)in production /dgdl/IPP_B093N06N3_Rev1.2.pdf?folderId=db3a3043163797a6011637c252b10018&fileId=db3a304317a7483601182c3043a67656D2PAK (TO-263)in production /dgdl/IPP032N06N3_Rev2.2.pdf?folderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e2a84ff084cc8/dgdl/IPB049NE7N3_Rev2.2.pdf?fD2PAK (TO-263)in production olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d590121a517a48e0bb9D2PAK (TO-263)in production /dgdl/IPB031NE7N3_Rev2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d590121a52a87680bc8/dgdl/IPB020NE7N3_Rev2.2.pdf?fD2PAK (TO-263)in production olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d590121e31c838554d3D2PAK (TO-263)in production /dgdl/IPP126N10N3+G_Rev2.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd012260508e027f74D2PAK (TO-263)in production /dgdl/IPP_I_B041N12N3_Rev2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd0122a75b86467ca4D2PAK (TO-263)in production /dgdl/IPP_I_B147N12N3+G_Rev2.6.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd0122a79a30f57d01D2PAK (TO-263)in production /dgdl/IPP_B_I_320N20N3+G+Rev2.3.pdf?folderId=db3a3043163797a6011637d4bae7003b&fileId=db3a3043243b5f170124967064ba184aD2PAK (TO-263)in production /dgdl/IPP_I_110N20N3+G_IPB107N20N3+G+Rev2.3.pdf?folderId=db3a3043163797a6011637d4bae7003b&fileId=db3a3043243b5f170124968e7d1f18e7/dgdl/IPP_B_I_200N25N3+G+RevD2PAK (TO-263)in production2.4.pdf?folderId=db3a3043163797a6011637d4bae7003b&fileId=db3a3043243b5f17012496b87e9f1971/dgdl/IPP_B_600N25N3+G+Rev2.D2PAK (TO-263)in production3.pdf?folderId=db3a3043163797a6011637d4bae7003b&fileId=db3a3043243b5f17012496c9548d199cD2PAK (TO-263)not for new design /dgdl/BUZ32+H3045A+rev+2.2.pdf?folderId=db3a304325305e6d012596c6ca7b290a&fileId=db3a304325305e6d01259718c8d8291eD2PAK (TO-263)not for new design /dgdl/BUZ31+H3045+A+Rev+2.1.pdf?folderId=db3a304325305e6d012596c6ca7b290a&fileId=db3a304325305e6d0125971c90292922D2PAK (TO-263)in production /dgdl/IPP_I111N15N3+G_IPB108N15N3+G_Rev2.1.pdf?folderId=db3a304325305e6d01254a567c041b4e&fileId=db3a304325305e6d01254a5795541b4fD2PAK (TO-263)in production /dgdl/Buz30a+H3045A+Rev+2.2.pdf?folderId=db3a304325305e6d012596c6ca7b290a&fileId=db3a304325305e6d012596cd45e4290folderId=db3a304326623792012669f6bee2224b&fileId=db3a30432662379201266a1f6dd2227c/dgdl/IPP110N20NA_IPB107N20NA+Rev2.1.pdf?folderId=db3a304325305e6d012596c6ca7b290a&fileId=db3a3043300464130130307ce52a20a3D2PAK (TO-263)in production/dgdl/IPB057N06N_Rev2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433727a44301372c2ed50b49b3D2PAK (TO-263)in production/dgdl/IPB026N06N_Rev2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a3043372d5cc8013754c7b2a74f7cD2PAK (TO-263)in production/dgdl/IPP_B230N06L3_Rev2.2_.pdf?folderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e2aab4a564d14D2PAK (TO-263)discontinued/dgdl/IPP070N08N3_Rev2.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431add1d95011ae849e8f1566bD2PAK (TO-263)in production/dgdl/IPP034N03L_rev2.0.pdf?folderId=db3a304313b8b5a60113cee8ed2a02db&fileId=db3a304313b8b5a60113d3c9730503e7D2PAK (TO-263)in production/dgdl/IPB009N03L_rev1.3.pdf?fold erId=db3a3043156fd5730115c7d50620107c&fileId=db3a3 0431689f4420116d426b6770ca3D2PAK 7pin (TO-2637pin)in production/dgdl/IPB011N04L_rev1.3.pdf?fold erId=db3a3043156fd5730115c7d50620107c&fileId=db3a3 0431689f4420116c451f4e20825D2PAK 7pin (TO-2637pin)in production/dgdl/IPB011N04N_rev1+4.pdf?fol derId=db3a3043163797a6011643468e7505a4&fileId=db3 a3043163797a601164373e07005f8D2PAK 7pin (TO-2637pin)in production/dgdl/IPB016N06L3_Rev2.3.pdf?f olderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3 a30431ddc9372011e261543e54693D2PAK 7pin (TO-2637pin)in production/dgdl/IPB017N06N3_Rev2.2.pdf?f olderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3 a30431ddc9372011e264a7ab746ea D2PAK 7pin (TO-2637pin)in production/dgdl/IPB019N08N3_Rev2.3.pdf?f olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db 3a30431add1d95011ae87fdf90569f D2PAK 7pin (TO-2637pin)in production/dgdl/IPB020N04N_rev1.3.pdf?fol derId=db3a304313b8b5a60113cee8763b02d7&fileId=db3 a30431936bc4b0119382c70a859ed D2PAK 7pin (TO-2637pin)in production/dgdl/IPB025N10N3+G_Rev2.03.p df?folderId=db3a304313b8b5a60113cee8763b02d7&fileId =db3a30431ce5fb52011d1ab1d9d51349D2PAK 7pin (TO-2637pin)in production/dgdl/IPB030N08N3_Rev2.3.pdf?f olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db 3a30431add1d95011ae88a47a856b1D2PAK 7pin (TO-2637pin)in productiondf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431ce5fb52011d1ed1fd3915e07pin)/dgdl/IPB036N12N3+G_Rev2.2.pd f?folderId=db3a304313b8b5a60113cee8763b02d7&fileId= db3a304323b87bc20123c7030ed51f56D2PAK 7pin (TO-2637pin)in production/dgdl/IPB065N15N3+G_Rev2.1.pd f?folderId=db3a304326623792012669f6bee2224b&fileId= db3a30432662379201266a0379d1225c D2PAK 7pin (TO-2637pin)in production/dgdl/IPB010N06N_Rev2.1.pdf?fol derId=db3a304313b8b5a60113cee8763b02d7&fileId=db3 a3043353fdc1601355341f17a485f D2PAK 7pin (TO-2637pin)in production/dgdl/IPB014N06N_Rev2.2.pdf?fol derId=db3a304313b8b5a60113cee8763b02d7&fileId=db3 a3043353fdc160135534e951e4873D2PAK 7pin (TO-2637pin)in production/dgdl/spd07n20_Rev+2.5.pdf?folderId=db3a30431a5c32f2011a809773886508&fileId=db3a30431f848401011fc73c3e60796aDPAK (TO-252)in production/dgdl/IPD031N06L3_Rev2.0.pdf?folderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e2a9f6a9d4d02DPAK (TO-252)in production/dgdl/IPD034N06N3_Rev2.0.pdf?folderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e2a97343b4cf3DPAK (TO-252)in production/dgdl/IPD035N06L3_Rev2.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431b3e89eb011b4558ed7f7d14DPAK (TO-252)in production/dgdl/IPD036N04L_rev1.0.pdf?folderId=db3a3043163797a6011643468e7505a4&fileId=db3a3043163797a6011643476a6505a5DPAK (TO-252)in production/dgdl/IPD038N06N3_Rev1.02.pdf?folderId=db3a3043132679fb0113346bdc4505a3&fileId=db3a304317a7483601181bf8dae11675DPAK (TO-252)in production/dgdl/IPD048N06L3_Rev2.0.pdf?folderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e2b4f496e4db0DPAK (TO-252)in production/dgdl/IPD053N08N3_Rev1.0.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304317a748360117cf072cf31ce8DPAK (TO-252)in production/dgdl/SPD50N03S2L-06+rev+1.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431b3e89eb011b9718a1a20e3cDPAK (TO-252)in production/dgdl/SPD30N03S2L-07+rev+1.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431b3e89eb011b92c6dcba0f89DPAK (TO-252)in production/dgdl/IPD068N10N3+G_Rev2.1.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431ce5fb52011d1eb7aeb615d1DPAK (TO-252)in production/dgdl/SPD50N03S2-07+rev+1.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431b3e89eb011b97117df80e2aDPAK (TO-252)in productionolderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e2b5528634dc0DPAK (TO-252)in production /dgdl/IPP086N10N3+G_Rev2.5.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431ce5fb52011d1ac5c8fa1358DPAK (TO-252)in production /dgdl/IPD088N06N3_Rev2.0.pdf?folderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e2b2351db4d5c/dgdl/IPD096N08N3_Rev2+1.pdf?DPAK (TO-252)in production folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431ce5fb52011d1f35150315feDPAK (TO-252)in production /dgdl/SPD30N03S2L-10+rev+1.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431b3e89eb011b96e752ea0e08/dgdl/IPD127N06LG%2BRev1.2.pDPAK (TO-252)not for new design df?folderId=db3a30431a5c32f2011a809773886508&fileId=db3a30431f848401011fc786d4077a24DPAK (TO-252)in production /dgdl/IPD135N08N3_Rev2.1.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431add1d95011ae8b1143256d4/dgdl/IPD160N04L_rev1.0.pdf?folDPAK (TO-252)not for new design derId=db3a3043163797a6011643468e7505a4&fileId=db3a3043163797a60116436401cf05cfDPAK (TO-252)not for new design /dgdl/IPD170N04N_rev1.0.pdf?folderId=db3a3043163797a6011643468e7505a4&fileId=db3a3043163797a601164367820f05dd/dgdl/IPD200N15N3_Rev2.05.pdfDPAK (TO-252)in production?folderId=db3a304313b8b5a60113cee7c66a02d6&fileId=db3a304319c6f18c0119cd1cc23279beDPAK (TO-252)in production /dgdl/SPD30N03S2L-20+rev+1.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431b3e89eb011b96f227b90e19/dgdl/IPD220N06L3_Rev2.0.pdf?fDPAK (TO-252)not for new design olderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e266fb35e471aDPAK (TO-252)in production /dgdl/IPP26CN10N_Rev1.08.pdf?folderId=db3a304412b407950112b408e8c90004&fileId=db3a304412b407950112b42b420244aa/dgdl/IPD250N06N3_Rev2.0.pdf?fDPAK (TO-252)not for new design olderId=db3a30431441fb5d01148ca9f1be0e77&fileId=db3a30431ddc9372011e268ceca1474fDPAK (TO-252)in production /dgdl/IPP35CN10N_Rev1.09.pdf?folderId=db3a304412b407950112b408e8c90004&fileId=db3a304412b407950112b42b457b44b1DPAK (TO-252)in production /dgdl/IPD350N06L+G++Rev1.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431be39b97011c320778777982?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431be39b97011c31db9a4f795cDPAK (TO-252)in production /dgdl/IPD640N06L%2BG%2BRev1.4.pdf?folderId=db3a30431ddc9372011ebafa04517f8b&fileId=db3a30431f848401011fcafb4ac00440DPAK (TO-252)in production /dgdl/IPP80CN10N_Rev1.09.pdf?folderId=db3a304412b407950112b408e8c90004&fileId=db3a304412b407950112b42c2aaf468dDPAK (TO-252)not for new design /dgdl/IPD800N06N%2BG%2BRev1.3.pdf?folderId=db3a30431ddc9372011ebafa04517f8b&fileId=db3a30431f848401011fcaff7887044fDPAK (TO-252)in production /dgdl/IPD122N10N3+G_Rev2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd0122604a0b2e7f65DPAK (TO-252)in production /dgdl/IPD180N10N3+G_Rev2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd01226070a4bb7fb9DPAK (TO-252)in production /dgdl/IPD_S110N12N3+G_Rev2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd0122a7a49e2b7d1dDPAK (TO-252)in production /dgdl/IPD031N03L_rev2+1.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432313ff5e01239e2ed62a6fffDPAK (TO-252)in production /dgdl/IPD040N03LG_rev1%5B1%5D.02.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432313ff5e01239e343d7c700fDPAK (TO-252)in production /dgdl/IPD050N03LG_rev1%5B1%5D.02.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432313ff5e01239e47dbfe701f/dgdl/IPD060N03LG_rev2.0.pdf?fDPAK (TO-252)in production olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432313ff5e01239e4d33a3702f/dgdl/IPD075N03LG_rev1%5B1%DPAK (TO-252)in production5D.1.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432313ff5e01239e56990c7047/dgdl/IPD090N03LG_rev2.0_.pdf?DPAK (TO-252)in production folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432313ff5e01239eac54cb707bDPAK (TO-252)in production /dgdl/IPD320N20N3+G+Rev2.3.pdf?folderId=db3a3043163797a6011637d4bae7003b&fileId=db3a3043243b5f1701249669796017f3/dgdl/IPD600N25N3+G+Rev2.3.pDPAK (TO-252)in productiondf?folderId=db3a3043163797a6011637d4bae7003b&fileId=db3a3043243b5f17012496b03c67195bDPAK (TO-252)in production /dgdl/IPD530N15N3_Rev2.5.pdf?folderId=db3a304326623792012669f6bee2224b&fileId=db3a30432662379201266a1f6dd2227c/dgdl/IPD105N03LG_rev2.1.pdf?fDPAK (TO-252)in production olderId=db3a304313b8b5a60113cee8ed2a02db&fileId=db3a3043271faefd0127b84794a33348/dgdl/IPD135N03LG_rev2.1.pdf?fDPAK (TO-252)in production olderId=db3a304313b8b5a60113cee8ed2a02db&fileId=db3a304327b897500127b8b9540f0003DPAK (TO-252)not for new design /dgdl/IPP12CN10N_Rev1.07.pdf?folderId=db3a304412b407950112b408e8c90004&fileId=db3a304412b407950112b42c236e467cDPAK (TO-252)in production /dgdl/IPD025N06N_Rev2.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304336415dec0136531648062c76/dgdl/IPD053N06N_Rev2.2.pdf?foDPAK (TO-252)in production lderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30433727a44301372c22c4c3499fI2PAK (TO-262)in production /dgdl/IPP_I023NE7N3_Rev2+11.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d5901210a9da8c22702I2PAK (TO-262)in production /dgdl/IPP_I034NE7N3_Rev2+01.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d5901210ab6d74b2720I2PAK (TO-262)in production /dgdl/IPP_I052NE7N3_Rev2+01.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304320d39d5901210ac80a8c273d/dgdl/IPP126N10N3+G_Rev2.3.pdI2PAK (TO-262)in productionf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd012260508e027f74I2PAK (TO-262)in production /dgdl/IPP180N10N3+G+Rev2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd01226066faa07f9dI2PAK (TO-262)in production /dgdl/IPP_I_B041N12N3_Rev2.2.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd0122a75b86467ca4I2PAK (TO-262)in production /dgdl/IPP_I076N12N3+G_Rev2.3.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd0122a77a83ab7cd4I2PAK (TO-262)in production /dgdl/IPP_I_B147N12N3+G_Rev2.6.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432239cccd0122a79a30f57d01I2PAK (TO-262)in production /dgdl/IPP045N10N3+G_Rev2.5.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431ce5fb52011d1e8b0cc31586I2PAK (TO-262)in production /dgdl/IPP086N10N3+G_Rev2.5.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30431ce5fb52011d1ac5c8fa1358I2PAK (TO-262)in production /dgdl/IPP030N10N3+G_Rev2%5B1%5D.1.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432313ff5e0123939fdbcf03c9/dgdl/IPP04CN10N_Rev1.4.pdf?foI2PAK (TO-262)not for new design lderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432313ff5e012393a80d1d03d8/dgdl/IPP072N10N3+G_Rev2%5BI2PAK (TO-262)in production1%5D.1.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432313ff5e012393bed2d20405/dgdl/IPP26CN10N_Rev1.08.pdf?fI2PAK (TO-262)discontinued olderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a30432313ff5e012393d285660441I2PAK (TO-262)discontinued /dgdl/IPP35CN10N_Rev1.09.pdf?folderId=db3a304313b8b5a60113cee8763b02d7&fileId=db3a304317a748360117cf1876cc1d1a。
Recom RAC AC DC Converter 产品说明说明书
RAC AC/DC ConverterFeaturesRegulated Converter• Wide input range 85-305VAC• Standby mode optimized (eco design Lot 6)• High efficiency over the entire load range • Operating temperature range: -40°C to +90°C • Overvoltage and overcurrent protected• EMC compliant without external components • Encapsulated module with pins or wiredDescriptionThe RAC05-K/277 series are multipurpose 5 watt AC/DC power supplies for enhanced mains input conditions from 90VAC up to 305VAC with an extra wide operating temperature range from -40°C to +90°C. These modules are designed to supply worldwide applications in automation, Industry 4.0, IoT, household and smart buildings. For worldwide use they come with international safety certifications for industrial, domestic and ITE as well as household standards. With both PCB-mount and wired packages, fully protected outputs, and EMC class B emissions compliance without any external components, these are the easiest to use modular power solutions in the industry.E224736RAC05-__ SK/277/WModel NumberingOrdering Examples:RAC05-05SK/277 5 Watt 5Vout Single Output THT version RAC05-24SK/277 5 Watt 24Vout Single Output THT version RAC05-05SK/277/W 5 Watt 5Vout Single Output Wired version RAC05-12SK/277/W5 Watt 12Vout Single Output Wired versionS inglenom. Output PowerOutput Voltage5 Watt Single OutputRAC05-K/277Selection GuidePart Input Output Output Efficiency Max. CapacitiveNumber Voltage Range Voltage Current typ (1) Load (2)[VAC] [VDC] [mA] [%] [µF]RAC05-3.3SK/277 85-305 3.3 1510 77 10000RAC05-05SK/277 85-305 5 1000 80 8000RAC05-12SK/277 85-305 12 416 83 1500RAC05-15SK/277 85-305 15 330 83 1000RAC05-24SK/277 85-305 24 210 84 330Notes:Note1: Efficiency is tested at nominal input and full load at +25°C ambient Note2: Max Cap Load is tested at nominal input and full resistive loadW ired Notes:Note3: add suffix …W“ for wired versionwithout suffix, standard THT versionUL62368-1 certified EN62368-1 certified IEC/EN60335-1 certified EN62233 certifiedIEC/EN61558-1 certified IEC/EN61558-2-16 certified EN55032 compliantEN55014-1(-2) compliant CB ReportSpecifications(measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)REGULATIONSParameterConditionValueOutput Accuracy ±1.0% typ.Line Regulation low line to high line, full load±0.5% typ. Load Regulation (7)10% to 100% load 1.0% typ.Transient Response25% load step change4.0% max.recovery time500µs typ.PROTECTIONSParameterTypeValueInput Fuse (8)internal T1A, slow blowShort Circuit Protection (SCP)below 100m Whiccup, automatic restart Over Voltage Protection (OVP)125% - 195%, latch of modeOver Voltage Category OVC IIOver Current Protection (OCP)125% - 195%, hiccup modeClass of EquipmentClass IIIsolation Voltage (safety certified) (9)I/P to O/P1 minute4.2kVACIsolation Resistance Isolation Voltage 500VDC 1G W min.Isolation Capacitance 100pF max.Insulation Grade reinforced Leakage Current0.25mA max.continued on next pageDeviation vs. Load(at 115VAC, 230VAC, 277VAC)10.50-0.5-1D e v i a t i o n [%]102030405060708090100Output Load [%]10.5-0.5-1D e v i a t i o n [%]0102030405060708090100Output Load [%]RAC05-05SK/277RAC05-12SK/277Notes:Note8: Refer to local safety regulations if input over-current protection is also required Note9: For repeat Hi-Pot testing, reduce the time and/or the test voltageNotes:Note7: Operation below 10% load will not harm the converter, but specifications may not be metSpecifications(measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)Specifications(measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)SAFETY AND CERTIFICATIONSCertificate Type (Safety)Report / File Number StandardAudio/Video, information and communication technology equipment - Part 1: Safety requirements E491408-A6004-ULUL62368-1, 2nd Edition, 2014-12-01CAN/CSA-C22.2 No. 62368-1-14, 2nd Edt., 2014-12Audio/Video, information and communication technology equipment -Part 1: Safety requirements (CB Scheme)E491408-A6007-CB-1IEC62368-1:2014 2nd EditionAudio/Video, information and communication technology equipment -Part 1: Safety requirements (LVD)EN62368-1:2014 + A11:2017Household and similar electrical appliances - Safety -Part 1: General requirementsLCS190308001CS IEC60335-1:2010 + A2:2016 + C1:2016, 5th Edt.EN60335-1:2012 + A13:2017Measurement methods for electromagnetic fields of household appliances and similarapparatus with regard to human exposureEN62233:2008Safety of power transformers, power supplies, reactors and similar products for sup-ply voltages up to 1100 V (CB Scheme)50230493 001IEC61558-1:2005 2nd Edition + A1:2009Safety of power transformers, power supplies, reactors and similar products for sup-ply voltages up to 1100 V Part 2: Particular requirements (CB Scheme)IEC61558-2-16:2009 1st Edition + A1:2013 Safety of power transformers, power supplies, reactors and similar products for sup-ply voltages up to 1100 VEN61558-1:2005 + A1:2009 Safety of power transformers, power supplies, reactors and similar products for sup-ply voltages up to 1100 V Part 2: Particular requirementsEN61558-2-16:2009 + A1:2013 RoHS2RoHS-2011/65/EU + AM-2015/863 EMC Compliance Conditions Standard / Criterion Low-voltage power supplies DC output - Part 3: Electromagnetic compatibility EN61204-3: 2018, Class B Electromagnetic compatibility of multimedia equipment - Emission requirements (11)EN55032:2015, Class B Electromagnetic compatibility - Requirements for household appliances, electric toolsand similar apparatus - Part 1: EmissionEN55014-1:2006 + A2:2011 I nformation technology equipment - Immunity characteristics - Limits and methods of measurement EN55024:2010 + A1:2015 Electromagnetic compatibility - Requirements for household appliances, electric toolsand similar apparatus - Part 2: ImmunityEN55014-2:2015ESD Electrostatic discharge immunity testAir: ±2, 4, 8kVContact: ±2, 4kVEN61000-4-2: 2009, Criteria BRadiated, radio-frequency, electromagnetic field immunity test 10V/m, 80MHz-1GHz3V/m, 1.4GHz-2GHz1V/m, 2GHz-2.7GHzEN61000-4-3: 2006 + A1, 2009, Criteria AFast Transient and Burst Immunity AC and DC Port: ±2kV EN61000-4-4: 2012, Criteria BSurge Immunity AC In Port (L-N): ±1kVDC Output Port: ±0.5kVEN61000-4-5: 2014 +A1:2017, Criteria BImmunity to conducted disturbances, induced by radio-frequency fields AC and DC Port: 10V EN61000-4-6: 2014, Criteria A Power Magnetic Field Immunity50Hz, 30A/m EN61000-4-8: 2010, Criteria AVoltage Dips and InterruptionsVoltage Dips: 30%Voltage Dips: 60%Voltage Dips: 100%Interruptions: >95%EN61000-4-11:2004 + A1:2017, Criteria CEN61000-4-11:2004 + A1:2017, Criteria CEN61000-4-11:2014 + A1:2017, Criteria BEN61000-4-11: 2014 + A1:2017,Criteria CVoltage Fluctuations and Flicker in Public Low-Voltage Systems <=16A per phase EN61000-3-3: 2013 Limitations on the amount of electromagnetic interference allowed from digital and electronic devices FCC 47 CFR Part 15 Supbart B, Class B Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical andElectronic Equipment in the Range of 9 kHz to 40 GHzANSI C63.4-2014, Class BNotes:Note11: If output is connected to GND, please contact RECOM tech support for adviceSpecifications(measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)Specifications (measured @ Ta= 25°C, nom. Vin, full load and after warm-up unless otherwise stated)The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM’s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorizeduse of RECOM products in such safety-critical applications.PACKAGING INFORMATIONParameterTypeValuePackaging Dimension (LxWxH)THT wiredtube tray466.0 x 30.4 x 29.3mm 468.0 x 198.0 x 46.0mmPackaging Quantity THT wired12pcs 24pcsStorage Temperature Range -40°C to +85°C Storage Humiditynon-condensing 20% to 90% RH max.。
LY G6SP.02 Advanced Power TOPLED
LY G6SP.02数据表LY G6SP.02数据表Published by ams-OSRAM AGTobelbader Strasse 30, 8141 Premstaetten, AustriaPhone +43 3136 500-0Advanced Power TOPLED ®LY G6SP.02新一代Advanced Power TOPLED.02 (APT.02) 采用艾迈斯欧司朗最先进的PLCC 6 封装，该封装在中功率 LED产品领域树立了行业标准，并且在过去的几十年前中作为主流的车规级封装被广为使用。
APT.02 系列凭借其稳定且坚固的设计，即使在严苛的使用环境条件下也能提供高水平的光电性能。
APT.02 系列产品使用了我们最新的InGaAlP芯片技术，以保证其优异的亮度性能，超高的发光效率及出色的散热能力。
应用-信号灯特点-封装: 白色SMT封装, 无色透明硅树脂 -芯片技术: Thinfilm-典型辐射值: 120° （朗伯发射极） -颜色: λdom = 590 nm (● yellow) -光效能: 44 lm/W -防腐蚀级别: 3B-认证: AEC-Q102 认证 RV-level 1-ESD: 2 kV acc. to ANSI/ESDA/JEDEC JS-001 (HBM, Class 2)订购信息型号发光强度 1)订单码I F = 140 mA I vLY G6SP.02-8D8E-36-G3R3-1406.3 ... 11.2 cdQ65113A3566最大额定参数图形符号值工作温度Top 最小值最大值-40 °C125 °C储存温度Tstg 最小值最大值-40 °C125 °C结温Tj最大值135 °C短时间应用的结温*Tj最大值150 °C 正向电流T S = 25 °CIF最小值最大值5 mA200 mA正向脉冲电流t ≤ 10 µs; D ≤ 0.005 ; TS = 25 °CIF pulse最大值1000 mA反向电压 2)T S = 25 °CVR最大值12 VESD耐受电压acc. to ANSI/ESDA/JEDEC JS-001 (HBM, Class 2)VESD2 kV* 当Tj = 150°C时，(L70/B50)的 中值寿命为100小时。
SCHOTTKY BARRIER DIODE LRB520S-商品说明书
DC
D=1/2 Sin(θ＝180)
10
0.001 0.01 0.1
1
10 100 1000
TIME:t(s)
Rth-t CHARACTERISTICS
0
0
0.1
0.2
0.3
0.4
0.5
AVERAGE RECTIFIED FORWARD CURRENT：Io(A) Io-Pf CHARACTERISTICS
10
15
Ifsm 8.3ms 8.3ms 10 1cyc
5
5
Ifsm t
0
1
10
100
NUMBER OF CYCLES IFSM-CYCLE CHARACTERISTICS
0
0.1
1
10
100
TIME:t(ms)
IFSM-t CHARACTERISTICS
10000
Mounted on epoxy board
75 100 125
AMBIENT TEMPERATURE:Ta(℃) Derating Curve (Io-Ta)
0.5
0.4 DC
0.3 D=1/2
0.2
0A
Io
0V t
VR D=t/T
VR=20V
T Tj=125℃
0.1 Sin(θ＝180)
0
0
25
50
75 100 125
CASE TEMPARATURE:Tc(℃) Derating Curve (Io-Tc)
LESHAN RADIO COMPANY, LTD. LRB520S-40T1G
FORWARD CURRENT:IF(mA)
MC13213资料
Freescale Semiconductor Technical DataFreescale reserves the right to change the detail specifications as may be required to permit improvements in the design of its products.Document Number: MC1321xRev. 0.0, 03/2006MC1321xPackage InformationCase 1664-0171-pin LGA [9x9 mm]Ordering InformationDevice Device MarkingPackage MC132********LGA MC132********LGA MC132********LGA MC13214113214LGA1See Table 1 for more details.1IntroductionThe MC1321x family is Freescale’s second-generation ZigBee platform which incorporates a low power 2.4 GHz radio frequency transceiver and an 8-bitmicrocontroller into a single 9x9x1 mm 71-pin LGA package. The MC1321x solution can be used for wireless applications from simple proprietary point-to-point connectivity to a complete ZigBee mesh network. The combination of the radio and a microcontroller in a small footprint package allows for a cost-effective solution.The MC1321x contains an RF transceiver which is an IEEE 802.15.4-compliant radio that operates in the 2.4 GHz ISM frequency band. The transceiver includes a low noise amplifier, 1mW nominal output power, PA with internal voltage controlled oscillator (VCO), integrated transmit/receive switch, on-board power supply regulation, and full spread-spectrum encoding and decoding.The MC1321x also contains a microcontroller based on the HCS08 Family of Microcontroller Units (MCU) and can provide up to 60KB of flash memory and 4KB of RAM. The onboard MCU allows the communicationsMC13211/212/213/214ZigBee ™- Compliant Platform - 2.4 GHz Low Power Transceiver for the IEEE ® 802.15.4 Standard plus MicrocontrollerContents1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 12MC1321x Pin Assignment and Connections 83MC1321x Serial Peripheral Interface (SPI) . 144IEEE 802.15.4 Modem . . . . . . . . . . . . . . . . . . 165MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256System Electrical Specification . . . . . . . . . 467Application Considerations . . . . . . . . . . . . . 638Mechanical Diagrams . . . . . . . . . . . . . . . . . . 68stack and also the application to reside on the same system-in-package (SIP). The MC1321x family is organized as follows:•The MC13211 has 16KB of flash and 1KB of RAM and is an ideal solution for low cost, proprietary applications that require wireless point-to-point or star network connectivity. TheMC13211 combined with the Freescale Simple MAC (SMAC) provides the foundation forproprietary applications by supplying the necessary source code and application examples to get users started on implementing wireless connectivity.•The MC13212 contains 32K of flash and 2KB of RAM and is intended for use with the Freescale fully compliant 802.15.4 MAC. Custom networks based on the 802.15.4 standard MAC can be implemented to fit user needs. The 802.15.4 standard supports star, mesh and cluster treetopologies as well as beaconed networks.•The MC13213 contains 60K of flash and 4KB of RAM and is also intended for use with the Freescale fully compliant 802.15.4 MAC where larger memory is required. In addition, this device can support ZigBee applications that use a stack from 3rd party vendors.•The MC13214 is a fully compliant ZigBee platform. The MC13214 contains 60K of flash and 4KB of RAM and uses the Figure 8 Wireless ZigBee Stack (Z-stack) software. Applications can beadded to develop fully certified ZigBee products.Applications include, but are not limited to, the following:•Residential and commercial automation—Lighting control—Security—Access control—Heating, ventilation, air-conditioning (HV AC)—Automated meter reading (AMR)•Industrial Control—Asset tracking and monitoring—Homeland security—Process management—Environmental monitoring and control—HV AC—Automated meter reading•Health Care—Patient monitoring—Fitness monitoring1.1Ordering InformationTable 1 provides additional details about the MC1321x family.1.2General Platform Features•IEEE 802.15.4 standard compliant on-chip transceiver/modem —2.4GHz—16 selectable channels—Programmable output power •Multiple power saving modes•2V to 3.4V operating voltage with on-chip voltage regulators •-40°C to +85°C temperature range •Low external component count•Supports single 16 MHz crystal clock source operation or dual crystal operation •Support for SMAC, IEEE 802.15.4, and ZigBee software •9mm x 9mm x 1mm 71-pin LGATable 1. Orderable Parts DetailsDevice Operating Temp Range(TA.)Package Memory Options DescriptionMC13211-40° to 85° C LGA1KB RAM, 16KB Flash Intended for proprietary applications and Freescale Simple MAC (SMAC)MC13211R2-40° to 85° C LGATape and Reel 1KB RAM, 16KB Flash Intended for proprietary applications and Freescale Simple MAC (SMAC)MC13212-40° to 85° C LGA2KB RAM, 32KB Flash Intended for IEEE 802.15.4 compliant applications and Freescale 802.15.4 MACMC13212R2-40° to 85° C LGATape and Reel 2KB RAM, 32KB Flash Intended for IEEE 802.15.4 compliant applications and Freescale 802.15.4 MACMC13213-40° to 85° CLGA4KB RAM, 60KB FlashIntended for IEEE 802.15.4 compliant applications and Freescale 802.15.4 MAC.Also supports ZigBee applications that use a stack from a 3rd party vendor.MC13213R2-40° to 85° CLGATape and Reel 4KB RAM, 60KB FlashIntended for IEEE 802.15.4 compliant applications and Freescale 802.15.4 MAC.Also supports ZigBee applications that use a stack from a 3rd party vendor.MC13214-40° to 85° C LGA4KB RAM, 60KB Flash Intended for full ZigBee compliant applications using the F8 Wireless Z-StackMC13214R2-40° to 85° CLGATape and Reel4KB RAM, 60KB FlashIntended for full ZigBee compliant applications using the F8 Wireless Z-Stack1.3Microcontroller Features•Low voltage MCU with 40 MHz low power HCS08 CPU core•Up to 60K flash memory with block protection and security and 4K RAM—MC13211: 16KB Flash, 1KB RAM—MC13212: 32KB Flash, 2KB RAM—MC13213: 60KB Flash, 4KB RAM—MC13214: 60KB Flash, 4KB RAM with ZigBee Z-stack•Low power modes (Wait plus Stop2 and Stop3 modes)•Dedicated serial peripheral interface (SPI) connected internally to 802.15.4 modem•One 4-channel and one 1-channel 16-bit timer/pulse width modulator (TPM) module with selectable input capture, output capture, and PWM capability.•8-bit port keyboard interrupt (KBI)•8-channel 8-10-bit ADC•Two independent serial communication interfaces (SCI)•Multiple clock source options—Internal clock generator (ICG) with 243 kHz oscillator that has +/-0.2% trimming resolution and +/-0.5% deviation across voltage.—Startup oscillator of approximately 8 MHz—External crystal or resonator—External source from modem clock for very high accuracy source or system low-cost option •Inter-integrated circuit (IIC) interface.•In-circuit debug and flash programming available via on-chip background debug module (BDM)—Two comparator and 9 trigger modes—Eight deep FIFO for storing change-of-flow addresses and event-only data—Tag and force breakpoints—In-circuit debugging with single breakpoint•System protection features—Programmable low voltage interrupt (LVI)—Optional watchdog timer (COP)—Illegal opcode detection•Up to 32 MCU GPIO with programmable pullups1.4RF Modem Features•Fully compliant IEEE 802.15.4 transceiver supports 250 kbps O-QPSK data in 5.0 MHz channels and full spread-spectrum encode and decode•Operates on one of 16 selectable channels in the 2.4 GHz ISM band•-1 dBm to 0 dBm nominal output power, programmable from -27 dBm to +3 dBm typical•Receive sensitivity of <-92 dBm (typical) at 1% PER, 20-byte packet, much better than the IEEE 802.15.4 specification of -85 dBm•Integrated transmit/receive switch•Dual PA ouput pairs which can be programmed for full differential single-port or dual-port operation that supports an external LNA and/or PA.•Three low power modes for increased battery life•Programmable frequency clock output for use by MCU•Onboard trim capability for 16 MHz crystal reference oscillator eliminates need for external variable capacitors and allows for automated production frequency calibration •Four internal timer comparators available to supplement MCU timer resources•Supports both packet data mode and streaming data mode•Seven GPIO to supplement MCU GPIO1.5Software FeaturesFreescale provides a wide range of software functionality to complement the MC1321x hardware. There are three levels of application solutions:1.Simple proprietary wireless connectivity.er networks built on the IEEE 802.15.4 MAC standard.3.ZigBee-compliant network stack.1.5.1Simple MAC (SMAC)•Small memory footprint (about 3 Kbytes typical)•Supports point-to-point and star network configurations•Proprietary networks•Source code and application examples provided1.5.2IEEE 802.15.4-Compliant MAC•Supports star, mesh and cluster tree topologies•Supports beaconed networks•Supports GTS for low latency•Multiple power saving modes (idle doze, hibernate)1.5.3ZigBee-Compliant Network Stack•Supports ZigBee 1.0 specification•Supports star, mesh and tree networks•Advanced Encryption Standard (AES) 128-bit security1.6System Block DiagramFigure1 shows a simplified block diagram of the MC1321x solution.Figure1. MC1321x System Level Block Diagram1.7System Clock ConfigurationThe MC321x device allows for a wide array of system clock configurations:•Pins are provided for a separate external clock source for the CPU. The external clock source can by derived from a crystal oscillator or from an external clock source•Pins are provided for a 16 MHz crystal for the modem clock source (required)•The modem crystal oscillator frequency can be trimmed through programming to maintain the tight tolerances required by IEEE 802.15.4•The modem provides a CLKO programmable frequency clock output that can be used as an external source to the CPU. As a result, a single crystal system clock solution is possible •Out of reset, the MCU uses an internally generated clock (approximately 8-MHz) for start-up. This allows recovery from stop or reset without a long crystal start-up delay•The MCU contains an internal clock generator (which can be trimmed) that can be used to run the MCU for low power operation. This internal reference is approximately 243 kHzFigure2. MC1321x Single Crystal System Clock Structure2MC1321x Pin Assignment and Connections Figure3 shows the MC1321x pinout.2.1Pin DefinitionsTable2 details the MC1321x pinout and functionality.Table2. Pin Function DescriptionPin #Pin Name Type Description Functionality1PTA3/KBI1P3DigitalInput/Output MCU Port A Bit 3 / Keyboard Input Bit 32PTA4/KBI1P4DigitalInput/Output MCU Port A Bit 4 / Keyboard Input Bit 43PTA5/KBI1P5DigitalInput/Output MCU Port A Bit 5 / Keyboard Input Bit 54PTA6/KBI1P6DigitalInput/Output MCU Port A Bit 6 / Keyboard Input Bit 65PTA7/KBI1P7DigitalInput/Output MCU Port A Bit 7 / Keyboard Input Bit 76VDDAD Power Input MCU power supply to ATD Decouple to ground.7PTG0/BKGND/MS DigitalInput/Output MCU Port G Bit 0 /Background / Mode SelectPTG0 is output only. Pin is I/O when used as BDMfunction.8PTG1/XTAL DigitalInput/Output/Output MCU Port G Bit 1 / Crystaloscillator outputFull I/O when not used as clock source.9PTG2/EXTAL DigitalInput/Output/Input MCU Port G Bit 2 / Crystaloscillator inputFull I/O when not used as clock source.10CLKO Digital Output Modem Clock Output Programmable frequencies of:16 MHz, 8 MHz, 4 MHz, 2 MHz, 1 MHz, 62.5 kHz,32.786+ kHz (default),and 16.393+ kHz.11RESET DigitalInput/OutputMCU reset. Active low12PTC0/TXD2DigitalInput/Output MCU Port C Bit 0 / SCI2 TX data out13PTC1/RXD2DigitalInput/Output MCU Port C Bit 1/ SCI2 RX data in14PTC2/SDA1DigitalInput/Output MCU Port C Bit 1/ IIC bus data15PTC3/SCL1DigitalInput/Output MCU Port C Bit 1/ IIC bus clock16PTC4DigitalInput/OutputMCU Port C Bit 417PTC5DigitalInput/OutputMCU Port C Bit 518PTC6DigitalInput/OutputMCU Port C Bit 619PTC7DigitalInput/OutputMCU Port C Bit 720PTE0/TXD1DigitalInput/Output MCU Port E Bit 0 / SCI1 TX data out21PTE1/RXD1DigitalInput/Output MCU Port E Bit 1/ SCI1 RX data in22VDDD Power Output Modem regulated outputsupply voltageDecouple to ground.23VDDINT Power Input Modem digital interfacesupply 2.0 to 3.4 V. Decouple to ground. Connect to Battery.24GPIO5DigitalInput/Output Modem General Purpose Input/Output 525GPIO6DigitalInput/Output Modem General Purpose Input/Output 626GPIO7DigitalInput/Output Modem General Purpose Input/Output 727XTAL1Input Modem crystal referenceoscillator inputConnect to 16 MHz crystal and load capacitor.28XTAL2Input/Output Modem crystal referenceoscillator output Connect to 16 MHz crystal and load capacitor. Do not load this pin by using it as a 16 MHz source. Measure 16 MHz output at CLKO, programmed for 16 MHz.29VDDLO2Power Input Modem LO2 VDD supply Connect to VDDA externally.30VDDLO1Power Input Modem LO1 VDD supply Connect to VDDA externally.31VDDVCO Power Output Modem VCO regulatedsupply bypassDecouple to ground.32VBATT Power Input Modem voltage regulators’inputDecouple to ground. Connect to Battery.33VDDA Power Output Modem analog regulatedsupply output Decouple to ground. Connect to directly VDDLO1 and VDDLO2 externally and to PAO_P andPAO_M through a bias network.34CT_Bias RF ControlOutput Modem biasvoltage/control signal forRF external componentsWhen used with internal T/R switch, providesground reference for RX and VDDA reference forTX. Can also be used as a control signal withexternal LNA, antenna switch, and/or PA.35RFIN_M RF Input(Output)Modem RF input/outputnegativeWhen used with internal T/R switch, this is abi-directional RF port for the internal LNA and PA36RFIN_P RF Input(Output)Modem RF input/outputpositiveWhen used with internal T/R switch, this is abi-directional RF port for the internal LNA and PATable2. Pin Function Description (continued)Pin #Pin Name Type Description Functionality37NC Not used May be grounded or left open38PAO_P RF Output Modem power amplifierRF output positive Open drain. Connect to VDDA through a bias network when used with external balun. Not used when internal T/R switch is used.39PAO_M RF Output Modem power amplifierRF output negative Open drain. Connect to VDDA through a bias network when used with external balun. Not used when internal T/R switch is used.40SM Input Test Mode pin Must be grounded for normal operation41GPIO4DigitalInput/Output Modem General Purpose Input/Output 442GPIO3DigitalInput/Output Modem General Purpose Input/Output 343GPIO2Test Point MCU Port E Bit 6 / ModemGeneral PurposeInput/Output 2Internally connected pins. When gpio_alt_en, Register 9, Bit 7 = 1, GPIO2 functions as a “CRC Valid” indicator.44GPIO1Test Point MCU Port E Bit 7 / ModemGeneral PurposeInput/Output 1Internally connected pins. When gpio_alt_en, Register 9, Bit 7 = 1, GPIO1 functions as an “Out of Idle” indicator.45VDD Power Input MCU main power supply Decouple to ground.46ATTN Test Point MCU Port D Bit 0 / Modemattention inputInternally connected pins.47PTD2/TPM1CH2DigitalInput/Output MCU Port D Bit 2 / TPM1 Channel 248PTD4/TPM2CH1DigitalInput/Output MCU Port D Bit 4 / TPM2 Channel 149PTD5/TPM2CH2DigitalInput/Output MCU Port D Bit 5 / TPM2 Channel 250PTD6/TPM2CH3DigitalInput/Output MCU Port D Bit 6 / TPM2 Channel 351PTD7/TPM2CH4DigitalInput/Output MCU Port D Bit 7 / TPM2 Channel 452PTB0/AD1P0Input/Output MCU Port B Bit 0 / ATDanalogChannel 053PTB1/AD1P1Input/Output MCU Port B Bit 1 / ATDanalog Channel 154PTB2/AD1P2Input/Output MCU Port B Bit 2 / ATDanalog Channel 255PTB3/AD1P3Input/Output MCU Port B Bit 3 / ATDanalog Channel 356PTB4/AD1P4Input/Output MCU Port B Bit 4 / ATDanalog Channel 4Pin #Pin Name Type Description Functionality57PTB5/AD1P5Input/Output MCU Port B Bit 5 / ATDanalog Channel 558PTB6/AD1P6Input/Output MCU Port B Bit 6 / ATDanalog Channel 659PTB7/AD1P7Input/Output MCU Port B Bit 7 / ATDanalog Channel 760VREFH Input MCU high referencevoltage for ATD61VREFL Input MCU low referencevoltage for ATD62PTA0/KBI1P0DigitalInput/Output MCU Port A Bit 0 / Keyboard Input Bit 063PTA1/KBI1P1DigitalInput/Output MCU Port A Bit 1 / Keyboard Input Bit 164PTA2/KBI1P2DigitalInput/Output MCU Port A Bit 2 / Keyboard Input Bit 265TEST Test Point For factory test Do not connect 66TEST Test Point For factory test Do not connect 67TEST Test Point For factory test Do not connect 68TEST Test Point For factory test Do not connect 69TEST Test Point For factory test Do not connect 70TEST Test Point For factory test Do not connect 71TEST Test Point For factory test Do not connectFLAG VSS Power input External package flag.Common VSS Connect to ground.Pin #Pin Name Type Description Functionality2.2Internal Functional InterconnectsThe MCU provides control for the 802.15.4 modem. The required interconnects between the devices are routed onboard the SiP. In addition, the signals are brought out to external pads primarily for use as test points. These signals can be useful when writing and debugging software.Table3. Internal Functional InterconnectsPin #MCU Signal Modem Signal Description43PTE6GPIO2Modem GPIO2 output acts as “CRC Valid” status indicator for Stream DataMode to MCU.44PTE7GPIO1Modem GPIO1 output acts as “Out of Idle” status indicator for Stream DataMode to MCU.46PTD0ATTN MCU Port D Bit 0 drives the attention (ATTN) input of the modem to wakemodem from Hibernate or Doze Mode.PTE5/SPSCK1SPICLK MCU SPI master SPI clock output drives modem SPICLK slave clock input.PTE4/MOSI1MOSI MCU SPI master MOSI output drives modem slave MOSI inputPTE3/MISO1MISO Modem SPI slave MISO output drives MCU master MISO inputPTE2/SS1CE MCU SPI master SS output drives modem slave CE inputIRQ M_IRQ Modem interrupt request M_IRQ output drives MCU IRQ inputPTD1RXTXEN MCU Port D Bit 1 drives the RXTXEN input to the modem to enable TX or RXor CCA operations.PTD3M_RST MCU Port D Bit 3 drives the reset M_RST input to the modem.NOTETo use the MCU and modem signals as described in Table3, the MCU needsto be programmed appropriately for the stated function.3MC1321x Serial Peripheral Interface (SPI)The MC1321x modem and CPU communicate primarily through the onboard SPI command channel. Figure4 shows the SiP internal interconnects with the SPI bus highlighted. The MCU has a single SPI module that is dedicated to the modem SPI interface. The modem is a slave only and the MCU SPI must be programmed and used as a master only. Further, the SPI performance is limited by the modem constraints of 8 MHz SPI clock frequency, and use of the SPI must be programmed to meet the modem SPI protocol.3.1SiP Level SPI Pin ConnectionsThe SiP level SPI pin connections are all internal to the device. Figure4 shows the SiP interconnections with the SPI bus highlighted.Figure4. MC1321x Internal Interconnects Highlighting SPI BusTable4. MC1321x Internal SPI ConnectionsMCU Signal Modem Signal DescriptionPTE5/SPSCK1SPICLK MCU SPI master SPI clock output drives modem SPICLK slave clock input.PTE4/MOSI1MOSI MCU SPI master MOSI output drives modem slave MOSI inputPTE3/MISO1MISO Modem SPI slave MISO output drives MCU master MISO inputPTE2/SS1CE MCU SPI master SS output drives modem slave CE input3.2SPI Features•MCU bus master •Modem bus slave•Programmable SPI clock rate; maximum rate is 8 MHz •Double-buffered transmit and receive at MCU•Serial clock phase and polarity must meet modem requirements (MCU control bits •Slave select programmed to meet modem protocol3.3SPI System Block DiagramFigure 5 shows the SPI system level diagram.Figure 5. SPI System Block DiagramFigure 5 shows the SPI modules of the MCU and modem in the master-slave arrangement. The MCU (master) initiates all SPI transfers. During a transfer, the master shifts data out (on the MOSI pin) to the slave while simultaneously shifting data in (on the MISO pin) from the slave. Although the SPI interface supports simultaneous data exchange between master and slave, the modem SPI protocol only uses data exchange in one direction at a time. The SPSCK signal is a clock output from the master and an input to the slave. The slave device must be selected by a low level on the slave select input (SS1 pin).7654321SPI SHIFTERCLOCK GENERATOR7654321SPI SHIFTER PTE2/SS1SPSCK1MISO1MOS1CESPICLKMISOMOSIMCU (MASTER)MODEM (SLAVE)4IEEE 802.15.4 Modem4.1Block DiagramFigure6. 802.15.4 Modem Block Diagram4.2Data Transfer ModesThe 802.15.4 modem has two data transfer modes:1.Packet Mode — Data is buffered in on-chip RAM2.Streaming Mode — Data is processed word-by-wordThe Freescale 802.15.4 MAC software only supports the streaming mode of data transfer. For proprietary applications, packet mode can be used to conserve MCU resources.4.3Packet StructureFigure7 shows the packet structure of the 802.15.4 modem. Payloads of up to 125 bytes are supported. The 802.15.4 modem adds a four-byte preamble, a one-byte Start of Frame Delimiter (SFD), and aone-byte Frame Length Indicator (FLI) before the data. A Frame Check Sequence (FCS) is calculated and appended to the end of the data.4 bytes 1 byte 1 byte125 bytes maximum 2 bytesPreamble SFD FLI Payload Data FCSFigure7. 802.15.4 modem Packet Structure4.4Receive Path DescriptionIn the receive signal path, the RF input is converted to low IF In-phase and Quadrature (I & Q) signals through two down-conversion stages. A Clear Channel Assessment (CCA) can be performed based upon the baseband energy integrated over a specific time interval. The digital back end performs Differential Chip Detection (DCD), the correlator “de-spreads” the Direct Sequence Spread Spectrum (DSSS) Offset QPSK (O-QPSK) signal, determines the symbols and packets, and detects the data.The preamble, SFD, and FLI are parsed and used to detect the payload data and FCS (which are stored in RAM in Packet Mode). A two-byte FCS is calculated on the received data and compared to the FCS value appended to the transmitted data, which generates a Cyclical Redundancy Check (CRC) result. A parameter of received energy during the reception called the Link Quality Indicator is measured over a 64 µs period after the packet preamble and stored in an SPI register.If the 802.15.4 modem is in Packet Mode, the data is stored in RAM and processed as an entire packet. The MCU is notified that an entire packet has been received via an interrupt.If the 802.15.4 modem is in streaming mode, the MCU is notified by a recurring interrupt on aword-by-word basis.Figure8 shows CCA reported power level versus input power. Note that CCA reported power saturates at about -57 dBm input power which is well above IEEE 802.15.4 Standard requirements. Figure9 shows energy detection/LQI reported level versus input power.NOTEFor both graphs, the required IEEE 802.15.4 Standard accuracy and rangelimits are shown. A 3.5 dBm offset has been programmed into the CCAreporting level to center the level over temperature in the graphs.FigureFigure4.5For the transmit path, the TX data that was previously written to the internal RAM is retrieved (packet mode) or the TX data is clocked in via the SPI (stream mode), formed into packets per the 802.15.4 PHY, spread, and then up-converted to the transmit frequency.If the 802.15.4 modem is in packet mode, data is processed as an entire packet. The data is first loaded into the TX buffer. The MCU then requests that the modem transmit the data. The MCU is notified via an interrupt when the whole packet has successfully been transmitted.In streaming mode, the data is fed to the 802.15.4 modem on a word-by-word basis with an interrupt serving as a notification that the 802.15.4 modem is ready for more data. This continues until the whole packet is transmitted.In both modes, a two-byte FCS is calculated in hardware from the payload data and appended to the packet. This done without intervention from the user.4.6Functional Description4.6.1802.15.4 Modem Operational ModesThe 802.15.4 modem has a number of operational modes that allow for low-current operation. Transition from the Off to Idle mode occurs when M_RST is negated. Once in Idle, the SPI is active and is used to control the IC. Transition to Hibernate and Doze modes is enabled via the SPI. These modes aresummarized, along with the transition times, in Table 5. Current drain in the various modes is listed in Table 8, DC Electrical Characteristics.4.6.2Serial Peripheral Interface (SPI)The MCU directs the 802.15.4 modem, checks its status, and reads/writes data to the device through the 4-wire SPI port. The transceiver operates as a SPI slave device only. A transaction between the host and the 802.15.4 modem occurs as multiple 8-bit bursts on the SPI. The modem SPI signals are:1.Chip Enable (CE) - A transaction on the SPI port is framed by the active low CE input signal. Atransaction is a minimum of 3 SPI bursts and can extend to a greater number of bursts.2.SPI Clock (SPICLK) - The host drives the SPICLK input to the 802.15.4 modem. Data is clockedinto the master or slave on the leading (rising) edge of the return-to-zero SPICLK and data out changes state on the trailing (falling) edge of SPICLK.Table 5. 802.15.4 Modem Mode Definitions and Transition TimesMode DefinitionTransition Time To or From IdleOff All IC functions Off, Leakage only. M_RST asserted. Digital outputs are tri-stated including IRQ10 - 25 ms to Idle Hibernate Crystal Reference Oscillator Off. (SPI not functional.) IC Responds to ATTN. Data is retained.7 - 20 ms to Idle DozeCrystal Reference Oscillator On but CLKO output available only if Register 7, Bit 9 = 1 for frequencies of 1 MHz or less. (SPI not functional.) Responds to ATTN and can be programmed to enter Idle Mode through an internal timer comparator. (300 + 1/CLKO) µs to Idle Idle Crystal Reference Oscillator On with CLKO output available. SPI active.Receive Crystal Reference Oscillator On. Receiver On.144 µs from Idle TransmitCrystal Reference Oscillator On. Transmitter On.144 µs from IdleNOTEFor the MCU, the SPI clock format is the clock phase control bit CPHA = 0and the clock polarity control bit CPOL = 0.3.Master Out/Slave In (MOSI) - Incoming data from the host is presented on the MOSI input.4.Master In/Slave Out (MISO) - The 802.15.4 modem presents data to the master on the MISOoutput.Although the SPI port is fully static, internal memory, timer and interrupt arbiters require an internal clock (CLK core), derived from the crystal reference oscillator, to communicate from the SPI registers to internal registers and memory.4.6.2.1SPI Burst OperationThe SPI port of the MCU transfers data in bursts of 8 bits with most significant bit (MSB) first. The master (MCU) can send a byte to the slave (transceiver) on the MOSI line and the slave can send a byte to the master on the MISO line. Although an 802.15.4 modem transaction is three or more SPI bursts long, the timing of a single SPI burst is shown in Figure10. The maximum SPI clock rate is 8 Mhz from the MCU because the modem is limited by this number.。
q_amp_spa-qf_usermanual_zh说明书
硬件用户手册Q-SYS SPA-Qf 系列网络放大器SPA-Qf 60x22 通道放大器，带 FlexIOSPA-Qf 60x44 通道放大器，带 FlexIOTD-001669-05-A*TD-001669-01*术语及符号说明“警告”一词表示有关人身安全的说明。
如果不遵照这些说明，可能会导致人身伤亡。
“小心”一词表示有关可能造成设备损坏的说明。
如果不遵照这些说明，可能会导致设备损坏，这种损坏不在质保范围内。
“重要信息”一词表示对于成功完成操作过程至关重要的说明或信息。
“注意”一词表示其他有用信息。
三角形内部的闪电箭头符号用于提醒用户注意产品外壳存在未绝缘的危险电压，可能对人体造成触电危险。
三角形内部的惊叹号用于提醒用户注意本手册中重要的安全、操作和维护说明。
重要安全说明警告！：为了防止火灾或电击，请勿将此设备暴露在雨中或潮湿环境中。
• 工作环境温度高——如果安装在封闭的或包含多台装置的机架总成中，则机架环境的工作温度可能高于室温。
确保其不超过所允许的最高工作温度范围 –请参阅第页的3页的“环境“部分。
• 气流减少——设备在机架中的安装应不会减少设备安全工作所需的气流量。
1. 请阅读、遵守并保存以下说明。
2. 请谨记所有警告。
3. 清洁设备时只能用干布擦拭。
4. 请勿将本产品安装在会产生热量的热源附近，如散热器、热调节装置、火炉或其他设备（包括放大器）。
5. 只能使用制造商指定的附件/配件。
6. 所有维修工作均应由合格的维修人员开展。
如果由于以下情况导致本设备损坏，必须进行维修：电源线或插头损坏，液体溅到本设备或物体落入本设备内部，设备遭到雨淋或受潮，不能正常工作或曾跌落。
7. 不要在靠近水或其他液体的地方使用本设备或将其浸入水或其他液体中。
8. 不要使用任何气溶胶喷雾、清洁剂、消毒剂或熏蒸剂清洁本设备及机器内部，请将以上制剂远离本设备。
9. 严格遵守所有适用的当地法规。
10. 如有任何关于物理设备安装的疑问或问题，请咨询持有执照的专业工程师。
WAGO 750-454 两通道分差输入模块说明说明书
Data sheet | Item number: 750-4542-channel analog input; 4 … 20 mA; Differential input; light gray/750-454Subject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products?Color:Item descriptionThis analog input module processes standard 4–20 V signals.The input signal is electrically isolated and transmitted with a resolution of 12 bits.The internal system supply powers the module.The input channels of the module are differential inputs.The shield directly connects to the DIN-rail.Subject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products?DataTechnical dataNumber of analog inputs2Total number of channels (module)2Signal typeCurrent Signal type (current)DC 4 … 20 mA Sensor connection 2 x (2-wire)Input voltage (max.)35 V Signal characteristic Differential Resolution [bit]12Bit Input resistance (max.)220ΩData width2 x 16-bit data; 2 x 8-bit control/status (optional)Conversion time (typ.)2ms Measurement error (reference temperature)25°C Measurement error – deviation (max.) from the upper-range value 0.2% Temperature error (max.) of the upper-range value 0.01%/KSupply voltage (system)5 VDC; via data contacts Power consumption (5 V system supply)70mAIsolation500 V system/fieldConnection dataConnection technology: inputs/outputs 8 x CAGE CLAMP ®Connection type (1)Inputs/OutputsSolid conductor0.08 … 2.5 mm² / 28 … 14 AWG Fine-stranded conductor 0.08 … 2.5 mm² / 28 … 14 AWG Strip length8 … 9 mm / 0.31 … 0.35 inchPhysical dataWidth 12 mm / 0.472 inch Height 100 mm / 3.937 inch Depth69.8 mm / 2.748 inch Depth from upper edge of DIN-rail62.6 mm / 2.465 inchMechanical dataMounting typeDIN-35 railSubject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products?Material dataColorlight grayHousing material Polycarbonate; polyamide 6.6Fire load 0.943MJ Weight49.8g Conformity markingCEEnvironmental requirementsSurrounding air temperature (operation)0 … 55 °C Surrounding air temperature (storage)-40 … 85 °C Protection type IP20Pollution degree (5) 2 per IEC 61131-2Operating altitude 0 … 2000 mMounting positionhorizontal (standing/lying); vertical Relative humidity (without condensation)95%Vibration resistance 4g per IEC 60068-2-6Shock resistance15g per IEC 60068-2-27EMC immunity to interference per EN 61000-6-2, marine applications EMC emission of interference per EN 61000-6-4, marine applications Exposure to pollutantsPer IEC 60068-2-42 and IEC 60068-2-43Permissible H S contaminant concentration at a relative humidity 75 2%10ppmPermissible SO contaminant concentration at a relative humidity 75 2%25ppm Commercial dataProduct Group 15 (Remote I/O)Packaging type BOX Country of origin DEGTIN4045454483098Customs tariff number853********Approvals / CertificatesEx-ApprovalsLogo Approval Additional Approval Text Certificate name ATEXTUEV Nord Cert GmbHEN 60079-0TÜV 07 ATEX 554086 X en.Subject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products?TUEV Nord Cert GmbH554086 X en.CCCExCQST/CNExCNCA-C23-012020312310000215EACBrjansker ZertifizierungsstelleTP TC 012/2011EAC RU C-DE.AM02.B.00163/19INMETROTÜV Rheinland do Brasil Ltda.IEC 60079BR-Ex_TÜV 12.1297XTUEV NordTUEV Nord Cert GmbHIEC 60079-0IECEx TUN 09.0001XULUnderwriters Laboratories Inc. (HAZARDOUS LOCATIONS)UL 121201E198726 Sec.1Country specific ApprovalsLogo ApprovalAdditional Approval Text Certificatename KCNational Radio Research AgencyArticle 58-2, Clause 3MSIP-REM-W43-AIM750Ship ApprovalsLogo ApprovalAdditional Approval Text Certificatename ABSAmerican Bureau of Shipping-19-HG1821926BVBureau Veritas S.A.-13453/DO BVSubject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products?DNV GLDet Norske Veritas, Germanischer Lloyd-TAA0000194KRKorean Register of Shipping-KRHMB05880-AC001LRLloyds Register-02/20026 (E6)NKNippon Kaiji Kyokai-TA17255MPRSPolski Rejestr Statków-TE/2236/880590/19RINARINA Germany GmbH-ELE066419XGUL-ApprovalsLogo ApprovalAdditional Approval Text Certificatename ULUL International Netherlands B.V. (ORDINARY LOCATIONS)UL 508E175199 Sec.1Compatible productsCarrier railItem no.: 210-112Steel carrier rail; 35 x 7.5 mm; 1 mm thick; 2 m long; slotted; according to EN 60715; "Hole width 25 mm; silver-colored/210-112Item no.: 210-113Steel carrier rail; 35 x 7.5 mm; 1 mm thick; 2 m long; unslotted; according to EN 60715; silver-colored /210-113Item no.: 210-114Steel carrier rail; 35 x 15 mm; 1.5 mm thick; 2 m long; unslotted; similar to EN 60715; silver-colored/210-114Subject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products?Steel carrier rail; 35 x 15 mm; 1.5 mm thick; 2 m long; unslotted; similar to EN 60715; silver-colored/210-114Item no.: 210-115Steel carrier rail; 35 x 7.5 mm; 1 mm thick; 2 m long; slotted; according to EN 60715; "Hole width 18 mm; silver-colored/210-115Item no.: 210-118Steel carrier rail; 35 x 15 mm; 2.3 mm thick; 2 m long; unslotted; according to EN 60715; silver-colored/210-118Item no.: 210-196Aluminum carrier rail; 35 x 8.2 mm; 1.6 mm thick; 2 m long; unslotted; similar to EN 60715; silver-colored/210-196Item no.: 210-197Steel carrier rail; 35 x 15 mm; 1.5 mm thick; 2 m long; slotted; similar to EN 60715; silver-colored/210-197Item no.: 210-198Copper carrier rail; 35 x 15 mm; 2.3 mm thick; 2 m long; unslotted; according to EN 60715; copper-colored/210-198Item no.: 210-504Steel carrier rail; 35 x 7.5 mm; 1 mm thick; 2 m long; slotted; galvanized; according to EN 60715/210-504Item no.: 210-505Steel carrier rail; 35 x 7.5 mm; 1 mm thick; 2 m long; unslotted; galvanized; according to EN 60715; silver-colored/210-505Item no.: 210-506Steel carrier rail; 35 x 15 mm; 1.5 mm thick; 2 m long; unslotted; galvanized; similar to EN 60715; silver-colored/210-506Item no.: 210-508Steel carrier rail; 35 x 15 mm; 1.5 mm thick; 2 m long; slotted; galvanized; similar to EN 60715; silver-colored/210-508Marking accessoriesItem no.: 2009-145Mini-WSB Inline; for Smart Printer; 1700 pieces on roll; stretchable 5 - 5.2 mm; plain; snap-on type; white/2009-145Item no.: 2009-145/000-002Mini-WSB Inline; for Smart Printer; 1700 pieces on roll; stretchable 5 - 5.2 mm; plain; snap-on type; yellow/2009-145/000-002Item no.: 2009-145/000-005Mini-WSB Inline; for Smart Printer; 1700 pieces on roll; stretchable 5 - 5.2 mm; plain; snap-on type; red/2009-145/000-005Item no.: 2009-145/000-006Mini-WSB Inline; for Smart Printer; 1700 pieces on roll; stretchable 5 - 5.2 mm; plain; snap-on type; blue /2009-145/000-006Item no.: 2009-145/000-007Mini-WSB Inline; for Smart Printer; 1700 pieces on roll; stretchable 5 - 5.2 mm; plain; snap-on type; gray /2009-145/000-007Item no.: 2009-145/000-012Subject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products?Item no.: 2009-145/000-012Mini-WSB Inline; for Smart Printer; 1700 pieces on roll; stretchable 5 - 5.2 mm; plain; snap-on type; orange/2009-145/000-012Item no.: 2009-145/000-023Mini-WSB Inline; for Smart Printer; 1700 pieces on roll; stretchable 5 - 5.2 mm; plain; snap-on type; green/2009-145/000-023Item no.: 2009-145/000-024Mini-WSB Inline; for Smart Printer; 1700 pieces on roll; stretchable 5 - 5.2 mm; plain; snap-on type; violet/2009-145/000-024Item no.: 248-501Miniature WSB Quick marking system; plain; Marker width 5 mm; 10 strips with 10 markers per card /248-501Item no.: 248-501/000-002Mini-WSB marking card; as card; not stretchable; plain; snap-on type; yellow/248-501/000-002Item no.: 248-501/000-005Mini-WSB marking card; as card; not stretchable; plain; snap-on type; red /248-501/000-005Item no.: 248-501/000-006Mini-WSB marking card; as card; not stretchable; plain; snap-on type; blue /248-501/000-006Item no.: 248-501/000-007Mini-WSB marking card; as card; not stretchable; plain; snap-on type; gray /248-501/000-007Item no.: 248-501/000-012Mini-WSB marking card; as card; not stretchable; plain; snap-on type; orange /248-501/000-012Item no.: 248-501/000-017Mini-WSB marking card; as card; not stretchable; plain; snap-on type; light green /248-501/000-017Item no.: 248-501/000-023Mini-WSB marking card; as card; not stretchable; plain; snap-on type; green /248-501/000-023Item no.: 248-501/000-024Mini-WSB marking card; as card; not stretchable; plain; snap-on type; violet /248-501/000-024Item no.: 750-100Marker card; as a DIN A4 sheet; plain; white /750-100Item no.: 750-103Group marker carrier; transparent/750-103Item no.: /750-106Subject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products?Item no.: 750-106Group marker carrier; transparent/750-106shield connectionItem no.: 790-108Shield clamping saddle; 11 mm wide; diameter of compatible conductor; 3 ... 8 mm/790-108Item no.: 790-116Shield clamping saddle; 19 mm wide; diameter of compatible conductor; 7 ... 16 mm/790-116Item no.: 790-124Shield clamping saddle; 27 mm wide; diameter of compatible conductor; 6 ... 24 mm/790-124Item no.: 790-140Shield clamping saddle; diameter of compatible conductor/790-140Item no.: 790-208Shield clamping saddle; 12.4 mm wide; 3 ... 8 mm/790-208Item no.: 790-216Shield clamping saddle; 21.8 mm wide; 6 ... 16 mm/790-216Item no.: 790-220Shield clamping saddle; 30 mm wide; 6 ... 20 mm/790-220system boxItem no.: 850-804IP65 enclosure; Stainless steel; WxHxD (400x123x200 mm); 4 x M20, 16 x M16, 28 x M12 cable grip/850-804Item no.: 850-804/000-001IP65 enclosure; Stainless steel; WxHxD (400x123x200 mm); 2 x M20, 13 x M16, 32 x M12 cable grip /850-804/000-001Item no.: 850-805IP65 enclosure; Stainless steel; WxHxD (600x123x200 mm); 4 x M20, 19 x M16, 67 x M12 cable grip/850-805Item no.: 850-814/002-000IP65 enclosure; Sheet steel (RAL 7035); WxHxD (200x120x200 mm); without flange plate/850-814/002-000Item no.: 850-815/002-000IP65 enclosure; Sheet steel (RAL 7035); WxHxD (300x120x200 mm); without flange plate /850-815/002-000Item no.: 850-816/002-000IP65 enclosure; Sheet steel (RAL 7035); WxHxD (400x120x200 mm); without flange plate /850-816/002-000Item no.: 850-817/002-000IP65 enclosure; Sheet steel (RAL 7035); WxHxD (600x120x200 mm); without flange plate /850-817/002-000Item no.: /850-825Subject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products?Item no.: 850-825IP65 enclosure; Aluminium (RAL 7032); WxHxD (160x100x160 mm); 9 x M12, 4 x M20/850-825Item no.: 850-826IP65 enclosure; Aluminium (RAL 7032); WxHxD (240x100x160 mm); 4 x M20, 4 x M16, 14 x M12 cable grip/850-826Item no.: 850-826/002-000IP65 enclosure; Aluminium (RAL 7035); WxHxD (240x100x160 mm); 4 x M20, 4 x M16, 14 x M12 cable grip/850-826/002-000Item no.: 850-827IP65 enclosure; Aluminium (RAL 7032); WxHxD (320x100x160 mm); 4 x M20, 8 x M16, 17 x M12 cable grip/850-827Item no.: 850-827/002-000IP65 enclosure; Aluminium (RAL 7035); WxHxD (320x100x160 mm); 4 x M20, 8 x M16, 17 x M12 cable grip/850-827/002-000Item no.: 850-828IP65 enclosure; Aluminium (RAL 7032); WxHxD (480x100x160 mm); 4 x M20, 10 x M16, 35 x M12 cable grip/850-828Item no.: 850-828/002-000IP65 enclosure; Aluminium (RAL 7035); WxHxD (480x100x160 mm); 4 x M20, 10 x M16, 35 x M12 cablegrip/850-828/002-000Item no.: 850-834IP65 enclosure; Polyester (RAL 7032); WxHxD (164x100x164 mm); 9 x M12, 4 x M20/850-834Item no.: 850-835IP65 enclosure; Polyester (RAL 7032); WxHxD (244x100x164 mm); 4 x M20, 4 x M16, 14 x M12 cable grip/850-835Item no.: 850-836IP65 enclosure; Polyester (RAL 7032); WxHxD (324x100x164 mm); 4 x M20, 8 x M16, 17 x M12 cable grip/850-836DownloadsDocumentationManual2-channel, 4-20mA, diff.V 1.2.0pdf 2.1 MBDownloadBid Text750-454X81 - Datei Feb 19, 2019xml 4.3 kB Download750-454doc - DateiOct 17, 2017doc 29.2 kBDownloadSubject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Do you have any questions about our products?750-454docx - Datei Oct 17, 2017docx 17.2 kBDownloadSystem Description750/753 Series I/O-System ‒ General Product Informationpdf 1.7 MB DownloadOverview on WAGO-I/O-SYSTEM 750 approvals pdf780.2 kBDownloadUse in Hazardous EnvironmentsTerm definition, marking and installation regulations V 1.0.0pdf 1.0 MBDownloadAdditional InformationDisposal; Electrical and electronic equipment, Packaging V 1.0.0pdf265.8 kBDownloadCAD/CAE-DataCAD data2D/3D Models 750-454URL DownloadCAE dataEPLAN Data Portal 750-454URL Download WSCAD Universe 750-454URL Download ZUKEN Portal 750-454URLDownloadDevice FilesDevice DriverWAGO USB Service Kabel Treiber / Serie 750 und 8576.5.3.0Sep 10, 2014zip 4.8 MBDownloadInstallation NotesData sheet | Item number: 750-454/750-454Subject to changes. Please also observe the further product documentation!WAGO Kontakttechnik GmbH & Co. KG Hansastr. 2732423 MindenPhone: +49571 887-0 | Fax: +49571 887-169 Email:****************|Web: Do you have any questions about our products?We are always happy to take your call at +49 (571) 887-44222.22.02.2021 Page /1111Product family750/753 Series I/O SystemShow all products from the family。
埃尔克斯电子产品的五种型号功能规范说明书
SPECIFICATIONS13Models 7520DT, 7530DT, 7540DT, 7550DT and 7564SAFunctional SpecificationsINPUTVoltage 115/230 VAC 15, Single Phase, User selection Frequency 50/60 Hz 5Fuse6.3 Amp 250V Slo-Blo for 7550DT and 7564SA 5 Amp 250V Slo-Blo for 75/20/30/40DTDIELECTRIC WITHSTAND TEST MODEOutput Rating5 KV @ 40 mA for 7550DT and 7564SA, 5 KV @ 20mA for 75/20/30/40DT6 KV @ 10 mA DC for 75/30/40/50DT and 7564SAOutput AdjustmentRange:0 - 5 KV AC 0 - 6 KV DCResolution: 1 volt/step Accuracy:(2 of setting 5 volts) Ramp-HI 12mA peak maximum, ON/OFF selectableCharge-LORange:0.0 - 350.0A DC or Auto setHI-Limit AC Range:0.00 - 40.00 mA for 7550DT and 7564SA, 0.00 - 20.00 mA for 75/20/30/40DT Resolution: 0.01 mA/step Accuracy: (2 of setting 2 counts) DC Range:0 - 9999AResolution: 1A/stepAccuracy:(2 of setting 2 counts) LO-Limit AC Range:0.000 - 9.999 mA Resolution: 0.001 mA/stepAccuracy: (2 of setting 2 counts) DC Range:0.0 - 999.9 AResolution: 0.1A/stepAccuracy:(2 of setting 2 counts) Arc Detection Range:1 - 9Failure DetectorAudible and VisualRecycledEquipment(410)email:***************************1981SPECIFICATIONS14Voltage Display Range: 0.00 - 6.00 KV Full Scale0.00 - 5.00 KV Full Scale for 7520DT onlyResolution: 10 volt/stepAccuracy: (2 of reading 2 counts)Current Display Auto RangeAC Range 1: 0.000mA - 3.500mAResolution: 0.001mA/stepRange 2: 3.00 - 40.00 mA for 7550DT and 7564SA,3.00 - 20.00 mA for 75/20/30/40DTResolution: 0.01 mA/stepDC Range 1: 0.0 A - 350.0 AResolution: 0.1A/stepRange 2: 300 A - 3500 AResolution: 1A/stepRange 3: 3000 A - 9990 AResolution: 10A/stepAccuracy: All Ranges (2 of reading 2 counts)DC Output Ripple 4**********************,ResistiveLoad Discharge Time 200 msMaximum CapacitiveLoad DC Mode1uF < 1KV0.75uF < 2KV0.5uF < 3KV0.08uF < 4KV0.04uF < 5KV0.01uF < 6KVAC Output Wave Form Sine Wave, Crest Factor = 1.3 - 1.5Output Frequency Range: 60 or 50 Hz, User SelectionAccuracy: 1%Output Regulation (1 of setting 5 volts) from no load to full load Dwell Timer Range: 0, 0.3 - 999.9 sec (0 = Constant)Resolution: 0.1 sec incrementsAccuracy: (0.1% + 0.05 sec)Ramp Timer Range: AC 0.1 - 999.9 secDC 0.4 - 999.9 secResolution: 0.1 sec incrementsAccuracy: (0.1% + 0.05 sec)RecycledEquipment(410)email:***************************SPECIFICATIONS15Ground Continuity For 75/20/30/40/50DT Current : DC 0.1 A 0.01A, fixedMax. ground resistance : 1 0.1, fixed Ground Fault Interrupt GFI Trip Current: HV Shut Down Speed: 450 A max (AC or DC)< 1msINSULATION RESISTANCE TEST MODE Model 75/30/40/50DT, 7564SAOutput VoltageRange:100 - 1000 Volts DC Resolution: 1 volt/step Accuracy:(2 of reading 2 volts) Short Circuit Current Maximum: 12mA peak Voltage DisplayRange: 0 - 1000 VResolution: 1 volt/stepAccuracy:(2 of reading 2 counts) Resistance DisplayRange: 1 - 9999 M (4 Digit, Auto Ranging)Resolution:500VDC 1000VDC M M M 0.001 1.000 - 5.388 1.000 - 9.999 0.01 1.40 - 53.88 2.80 - 99.99 0.1 14.0 - 538.8 28.0 - 999.9 1104 - 9999280 - 9999Accuracy:(2 of reading 2 counts) at test voltage 500 - 1000V and 1 - 1000 M(8 of reading 2 counts) at test voltage 500 - 1000V and 1000 - 9999 M(8 of reading 2 counts) at test voltage 100 - 500V and 0 - 1000 MCharge-LO Range: 0.000 - 3.500A or Auto Set HI-Limit Range: 0 - 9999 M (0 = Off) LO-Limit Range: 1 - 9999 MDelay TimerRange: 0, 0.5 - 999.9 sec (0 = Constant) Resolution: 0.1 sec/stepAccuracy:(0.1% + 0.05 sec)Ground Fault InterruptGFI Trip Current:HV Shut Down Speed:450 A max (AC or DC) < 1msRecycledEquipment(410)email:***************************SPECIFICATIONS16GROUND BOND TEST MODE Model 7564SA onlyOutput Voltage Range: 3.00 - 8.00 Volts AC (Open Circuit Limit) Resolution: 0.01 volt/stepAccuracy: (2 % of Setting + 0.03V ) O.C. Condition Output Frequency Range: 60 or 50 Hz, User Selection Accuracy: 1%Output CurrentRange: 3.00 - 30.00 Amps AC Resolution: 0.01 Amp/stepAccuracy :(2 % of Setting + 0.02 A) Current DisplayRange: 0.00 - 30.00 Amps Resolution: 0.01 Amp/stepAccuracy:(3 % of Reading + 0.03 A) Resistance DisplayRange: 0 - 600 m Resolution: 1 m /stepAccuracy:(2 % of Reading + 2 m ) HI-LimitRange: 0 - 600 m for 3 - 10 A 0 - 150 m for 3 - 30 A Resolution: 1 m /stepAccuracy:(2 % of Setting + 2 m ) LO-LimitRange: 0 - 600 m for 3 - 10 A 0 - 150 m for 3 - 30 A Resolution: 1 m /stepAccuracy:(2 % of Setting + 2 m ) Dwell TimerRange: 0, 0.5 - 999.9 sec (0 = Constant) Resolution: 0.1 sec/step Accuracy:(0.1% + 0.05 sec)Milliohm OffsetMax. Offset Capability: 200 mResolution: 1 m / stepAccuracy:(2 % of Setting + 2 m )RecycledEquipment(410)email:***************************SPECIFICATIONS17GENERAL SPECIFICATIONSPLC Remote Control Input - Test, Reset, Recall memory 1, 2 and 3Output - Pass, Fail, Test-in-ProcessMemory Allows storage of up to 50 groups different test programsand 8 step/each memory. Step is not available on 7520DT SecurityProgrammable password lockout capability to avoid unauthorized access to test set-up program. LCD Contrast Setting 9 ranges set by the numeric keys on the front panel. Buzzer Volume Setting 10 ranges set by the numeric key on the front panel.Calibration Software and adjustments are made through front panel. Mechanical Bench or rack mount with tilt up front feet. Dimension7540DT, 7550DT and 7564SA:(W x H x D) 17 x 5.8 x 20.3 in. (432 x 147 x 515 mm) 7520DT and 7530DT:(W x H x D) 17 x 5.8 x 12 in. (432 x 147 x 305 mm)Weight7564SA without scanner 52.5 lbs (24 Kgs) 7564SA with built-in scanner 57.0 lbs (26 Kgs) 7550DT without scanner 50.5 lbs (23 Kgs) 7550DT with built-in scanner 55.0 lbs(25 Kgs) 7540DT with 4 port scanner 39.6 lbs (18 Kgs) 7540DT with 8 port scanner41.8 lbs(19 Kgs) 7530DT scanner not available 24.8 lbs (11.27 Kgs) 7520DT scanner not available 24.8 lbs(11.27 Kgs)Scanner Port Two Port Maximum including the built-in scanner. Not available on 7520DT, 7530DT and 7540DT.Scanner Built-in OptionHigh Voltage x 4 Ports (7540DT only)High Voltage x 8 Ports (75/40/50DT and 7564SA) Ground Bond x 8 Ports (7564SA only)RecycledEquipment(410)email:***************************。
ioLogik 2500 Series (GPRS) 固件发布说明书
Firmware for ioLogik 2500 Series (GPRS) Release NotesSupported Operating SystemsNotesChangesApplicable ProductsBugs FixedN/A• Fixed where using FTP Upload action in Click&Go Plus triggers abnormal device reboot.• Fixed AI scaling result and web display error.• Fixed where using TCP Message action in Click&Go Plus triggers abnormal device reboot.EnhancementsN/AioLogik 2542-GPRS(-T), ioLogik 2512-GPRS(-T)N/ANew FeaturesN/AN/ASupported Operating SystemsNotesChangesApplicable ProductsBugs Fixed• Counter Value can be set by user through Modbus/TCP, AOPC, SNMP, RESTful API.• DO safe mode Hold Last function added.• ioLogik E1200 expansion unit connection status registers added.• ioLogik E1200 expansion unit auto-reconnection function added.• Unencrypted system log content added.• Fixed NTP only updates once for daylight saving time.• Fixed weekday and time zone mismatch issue.• Fixed counter initial value reset to 0 after counter scaling is enabled.• Fixed counter value reset to 0 when device is reconnected with MX-AOPC UA Server.• Fixed AI keyword replacement error for active messages from Click&Go Plus.• Fixed Click&Go DO lock issue when power on delay occurs.• Fixed unable to show special characters on web dashboard.• Fixed alias name with special characters issue.• Fixed AI on change update not triggered when variance<1.EnhancementsN/AioLogik 2512-HSPA, ioLogik 2512-HSPA-T, ioLogik 2542-HSPA, ioLogik 2542-HSPA-T• Modbus/TCP Master function.• RESTful API protocol support.• HTTPS support.• Counter power off storage function.• Counter overflow flag.• Service Setting to Enable/Disable all services on one page.• Access Control function for login attempt and lockout.• User Settings operator, user account enable/disable.• Password expiry time and notification configuration.• System use notification added on login page.• Internal registers BOOL and DWORD.• AOPC alive check for port 9500.New Features• Updated password requirements.N/ASupported Operating SystemsNotesChangesApplicable ProductsBugs Fixed• Improved device time accuracy.N/AEnhancementsN/AioLogik 2512-GPRS-T, ioLogik 2512-GPRS, ioLogik 2542-GPRS, ioLogik 2542-GPRS-TN/ANew FeaturesN/AN/ASupported Operating SystemsNotesChangesApplicable ProductsBugs FixedN/A• Fixed DO incorrect ON CHANGE status issue, which happened on Online Web interface, Modbus,AOPC, and Data Logging functions.• Fixed FTP Client return code (450) handling issue for FTP server.• Fixed Serial Mode setting mismatch (485-2W/422).EnhancementsN/AioLogik 2512-GPRS, ioLogik 2512-GPRS-T, ioLogik 2542-GPRS, ioLogik 2542-GPRS-T• Supports MXIO V3.0.• Supports MX-AOPC UA Logger data supplement function.• User Settings for three roles: Administrator, Operator, and User.• Access Control for allowing IP addresses to access through the Modbus protocol.• Three TC modes (78.126 mV, 39.062 mA, 19.532 mV) for ioLogik E1262 as I/O expansion.• Added “Power on Delay” settings for relay channels of ioLogik E1214 as I/O expansion.• Modbus address for raw value of AI, AO, TC, and RTD.• Modbus address for relay current count value, relay total count value, and reset relay current count value for ioLogik E1214 as I/O expansion.• Click&Go Plus IF condition for “relay current count value” and “total count value”.• Click&Go Plus Action for “Reset relay current count value”.• Modbus host connection timeout settings.• Click&Go Plus IF condition for “Modbus host connection status”.• Click&Go Plus IF condition for RTD and TC value comparison.• Enable/disable option for FTP server service.• Timestamp options (device local time or UTC and time zone) for data logging function.• Peer-to-Peer disconnection mode settings for DO and AO channels.• Communication timeout settings for FTP Client, Email, CGI Command Client, TCP Message, and Remote Action Client.• Checksum algorithm to improve correctness of configuration file transfer between IOxpress and Device.• Search device by IP address function.• Click&Go Plus IF condition for “Cellular link up”.• RSSI tag.• Added “Cellular IP” in keyword lookup options of SNMP trap, TCP/UDP message, email, and SMS.• Online web and configuration compatibility check, and guide user to import configuration through IOxpress.• Web server, FTP server, and Modbus TCP server connections in Network Connection status of Web Console.• Web console access rights by user type.New FeaturesN/AN/ASupported Operating SystemsNotesChangesApplicable ProductsBugs FixedN/A• Fixed a malfunction that occurs while importing configurations with empty rules to the device via the web.EnhancementsN/AioLogik 2512-GPRS, ioLogik 2512-GPRS-T, ioLogik 2542-GPRS, ioLogik 2542-GPRS-TN/ANew FeaturesN/AN/A。
赛米控丹佛斯电子 Board_4S_SKYPER_32_PRO_R_Gold 数据表
1®Adaptor boardAdaptor boardOrder Nr. L5062701Board 4S SKYPER 32 PRO R GoldFeatures•Two output channels •Gold nickel finish •Failure managementTypical Applications*•Adaptor board for SKYPER 32 IGBT drivers in bridge circuits for industrial applications •PCB with gold plating •DC bus up to 1000VRemarks•With external high voltage diode•Please Note: the insulation test is not performed as a series test atSEMIKRON and must be performed by the user•According to VDE 0110-20•Insulation coordination in compliance with EN50178 PD2•Operating temperature is real ambient temperature around the driver core •Degree of protection: IP00Absolute Maximum Ratings SymbolConditionsValuesUnitV s Supply voltage primary 16V Iout PEAK Output peak current 15A Iout AVmax Output average current 50mA f max Max. switching frequency50kHz V CECollector emitter voltage sense across the IGBT1700V V isol IO Insulation test voltage input - output (AC, rms, 2s)4000V V isolPD Partial discharge extinction voltage, rms, Q PD ≤ 10pC1200V V isol12Insulation test voltage output 1 - output 2 (AC, rms, 2s)1500V R Gon minMinimum rating for external R Gon 1.5ΩR Goff min Minimum rating for external R Goff 1.5ΩT op Operating temperature -40...85°C T stgStorage temperature-40 (85)°CCharacteristics SymbolConditionsmin.typ.max.UnitV s Supply voltage primary side 14.41515.6V V i Input signal voltage on / off 15 / 0V V IT+Input threshold voltage (HIGH)12.3V V IT-Input threshold voltage (LOW) 4.6V V G(on)Turn on output voltage 15V V G(off)Turn off output voltage-7V t d(on)IO Input-output turn-on propagation time 1.2µs t d(off)IOInput-output turn-off propagation time1.2µsThis is an electrostatic discharge sensitive device (ESDS), international standard IEC 60747-1, chapter IX.*IMPORTANT INFORMATION AND WARNINGSThe specifications of SEMIKRON products may not be considered as guarantee or assurance of product characteristics ("Beschaffenheitsgarantie"). The specifications of SEMIKRON products describe only the usual characteristics of products to be expected in typical applications, which may still vary depending on the specific application. Therefore, products must be tested for the respective application in advance. Application adjustments may be necessary. The user of SEMIKRON products is responsible for the safety of their applications embedding SEMIKRON products and must take adequate safety measures to prevent the applications from causing a physical injury, fire or other problem if any of SEMIKRON products become faulty. The user is responsible to make sure that the application design is compliant with all applicable laws, regulations, norms and standards. Except as otherwise explicitly approved by SEMIKRON in a written document signed by authorized representatives of SEMIKRON, SEMIKRON products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury. No representation or warranty is given and no liability is assumed with respect to the accuracy, completeness and/or use of any information herein, including without limitation, warranties of non-infringement of intellectual property rights of any third party. SEMIKRON does not assume any liability arising out of the applications or use of any product; neither does it convey any license under its patent rights, copyrights, trade secrets or other intellectual property rights, nor the rights of others. SEMIKRON makes no representation or warranty of non-infringement or alleged non-infringement of intellectual property rights of any third party which may arise from applications. Due to technical requirements our products may contain dangerous substances. For information on the types in question please contact the nearest SEMIKRON sales office. This document supersedes and replaces all information previously supplied and may be superseded by updates. SEMIKRON reserves the right to make changes.2。
Model 7265 DSP Lock-in Amplifier 信号恢复仪说明书
Dual Reference In this mode the instrument can make simultaneous measurements on two signals at different reference frequencies, which is ideal, for example, for use in source compensated optical experiments
Graphical Display
The model 7265 is extremely easy to use. All instrument controls are adjusted using soft-touch, front panel push-buttons, with the present settings and measured outputs being displayed on the centrally located, cold fluorescent backlit dot-matrix LCD. A particularly convenient feature is the pop-up keypad which is
External control of the unit is via either the RS232 or GPIB interfaces, using simple mnemonic-type ASCII commands. A second RS232 port allows up to sixteen 7265 or compatible instruments to be operated from a single RS232 computer port by connecting them in a “daisy-chain” configuration.
Foxboro 43AP Pneumatic Indicating Controllers 产品说明
FIELD DEVICES – CONTROLLERSProduct Specifications43AP Pneumatic Indicating ControllersThese instruments indicate and control pressure, temperature, vacuum, and differential pressure. They provide process industries with a highly dependable and versatile group of instruments.WIDE SELECTION OF MEASURING ELEMENTS Foxboro products offer the widest variety of element constructions and ranges in the industry. This versatility enables the 43AP Series Pneumatic Indicating Controllers to be applied to virtually any process.WIDE CHOICE OF CONTROL MODESOn-off, proportional, proportional plus derivative, proportional plus integral (reset), proportional plus integral plus derivative, differential gap, and automatic shutdown actions are available.BROAD RANGE OF INTEGRAL (RESET) AND DERIVATIVE ADJUSTMENTSThe integral unit has the complete range from0.01to 50 minutes, and the derivative unit from 0.05 to 50 minutes.VARIETY OF OPTIONSThese controllers are available with an extensive list of optional features. Among these are internal bumpless automatic-manual transfer stations (two types), “batch” function, remote pneumatic set point, Type 70 electric contacts, and control valvemounting.PSS 3-1B3 APSS 3-1B3 APage 2OPERATING CONDITIONSACCURACY UNAFFECTED BY MOUNTING STRESSESBoth the control unit and the measurement element are mounted on a rigid steel plate. Thus, these components are isolated from case stresses due to mounting, and dependable accuracy is ensured. POWER FAILURES DO NOT INFLUENCE PROCESS-DRIVEN INDICATIONA power failure and the likely subsequent loss of supply pressure do not influence the process-driven indication.WEATHERPROOF CONSTRUCTIONA glass fiber reinforced case and a gasketed door with a shatterproof polycarbonate window meet IEC IP53 and provide the environmental protection of NEMA®T ype 3.VERSATILE MOUNTINGInstruments may be mounted in a panel, on a flat surface, on a continuous vertical pipe, or on a vertical pipe stub.INTERNAL BUMPLESS AUTOMATIC-MANUAL TRANSFER STATIONThis option provides bumpless-balanceable transfer between automatic and manual control by simple 2-step procedure. Accidental transfer is avoided because the door must be opened to gain access to the transfer station.PERFORMANCE SPECIFICATIONS(Under Reference Operating Conditions unless otherwise specified)AccuracyINPUT TO POINTER±0.5% of span for qualified elements.INPUT TO OUTPUTDepends on measuring element used. Repeatability0.2% of span.Deadband0.1% of span.Ambient Temperature EffectMaximum control point shift at midspan per 55°C (100°F) change within normal operating conditions is 1% of input span.Supply Pressure EffectMaximum control point shift at midspan per 7 kPa (1psi) change within normal operating conditions is 0.2% of input span.OPERATING CONDITIONSAmbient T emperature24 ±2°C(75 ±3°F)–30 and +80°C(–20 and +180°F)–40 and +80°C(–40 and +180°F)Relative Humidity50% ± 10%No Limit No LimitSupply Pressure140 ± 1.4 kPa(20 ± 0.2 psi)115 and 155 kPa(17 and 23 psi)210 kPa(30 psi)FUNCTIONAL SPECIFICATIONSPSS 3-1B3 APage 3 FUNCTIONAL SPECIFICATIONSElementsRefer to “Measuring Element Specifications” on page4 for types, materials, and ranges. Controller ActionOutput signal either increases or decreases with increasing measurement, as specified; action is reversible in the field.Output Signal20 to 100 kPa, 3 to 15 psi, or 0.2 to 1.0 bar or kg/cm2, as specified.Air Consumption (Under normal operation)0.5 m3/h (0.3 cfm) at standard conditions.Output Gauge0 to 200 kPa, 0 to 30 psi, or 0 to 2 bar or kg/cm2, as specified.Set Point AdjustmentBy means of a knob mounted inside the case. PointersSet point and measurement pointers are fluorescent red.ScaleBlack markings on white background; sector-shaped with nominal effective length of 150 mm (6 in). (Refer to Chart and Dial Catalog 600 for available ranges.)Connections (Located in Bottom of Case.) PRESSURE AND VACUUMFor upper range-values up to 14 MPa(2000psi, or 140 bar or kg/cm2):Connections tapped for R1/4 or 1/4 NPT, asspecified.For upper range-values from 14 MPa(2000psi, or 140 bar or kg/cm[sup/2]) up to70 MPa (10000psi, or 700 bar or kg/cm2):Connections threaded for R1/2 or 1/2 NPT,as specified.For upper range-values above 70 MPa (10000psi, or 700 bar or kg/cm2):9/16-18 Aminco® fitting used.PNEUMATICSupply and output connections tapped for1/4NPT.MountingPANELFlush in a panel up to 16 mm (0.6 in) thick.SURFACESuitable for all controllers having internally-mounted elements. Note that this mounting isnot available with heavy duty helical elements.(These elements extend through the back of the case.)PIPEA kit of parts to fit a DN 50 or 2 in vertical pipe.YOKEKit of parts to fit a vertical DN 50 or 2 in pipestub. This mounting scheme is designedspecifically for controllers having rear-mounted differential pressure elements.PSS 3-1B3 A Page 4PHYSICAL SPECIFICATIONSPHYSICAL SPECIFICATIONSEnclosureThe case is a glass fiber reinforced polyester molding, compounded for superior corrosion resistance. The door is glass fiber reinforced phenylene oxide, and has a shatterproofpolycarbonate window, ultraviolet resistant. The overall construction is weatherproof, meets IEC IP53, and provides the environmental protection of NEMA Type 3.FinishCase, gray polyester; door, blue textured polyurethane.Data LabelAluminum data label fastened to inside of door with pressure sensitive adhesive. Includes space for Customer Tag data up to a maximum of 72characters and spaces. For additional space, see optional Customer T ag.Approximate Mass4.8 kg (10.6 lb), excluding element.MEASURING ELEMENT SPECIFICATIONS (To achieve stated Performance Specifications)Differential Pressure Elements (Refer to PSS 3-4A2 A)a.Body and cover material for DE-A is zinc-cobalt; material for DE-B is 316 ss.b.These are zero-based elements. The lower range value is zero and the upper range value is as shown (100% of span). Zerodifferential pressure can be elevated (compound range) so that lower range value is as low as -50% of span; or suppressed so that upper range value is as high as either –150% of span or 50 kPa (200 inH 2O) ∆P , whichever is less.22DE–A,BType 375 and 5020 and 20050 and 500142000140Temperature Elements—Filled Thermal Systems (Refer to PSS 3-3A1 A)T A–1A IA –130 and +315–200 and +60025 and 33040 and 600TA–2A and 2BIIA and IIB–45 and +315–50 and +600Varies with operating temperature (a)T A–3BIIIB–195 and +760–320 and +140070 and 550120 and 1000a.Does not include temperature overrange values. Narrow spans are at low end of range. The maximum span is 215︒C (400︒F)MEASURING ELEMENT SPECIFICATIONS PSS 3-1B3 APage 5Pressure Elements (Refer to PSS 3-2A1 A)P A–CA (d)Absolute Bellows316 ss170 and 240 kPa abs 2.5 and 35 psia P A–MA Absolute Double Spiral316 ss140 and 700 kPa abs20 and 100 psiaPB–AA PB–AM (e)Helical316 ssK-Monel1.4 and 40 MPa1.7 and 14 MPa200 and 6000 psi200 and 2000 psiPB–BA PB–BM (e)Spiral316 ssK-Monel82 and 1400 kPa140 and 1400 kPa12 and 200 psi20 and 200 psiPB–CA Bellows316 ss35 and 200 kPa 4.5 and 29 psiPB–CC Bellows Brass34 and 100 kPa vac30 and 180 kPa 4.9 and 15 psi 4 and 26 psiPB–DF Diaphragm 50 mm (2 in)Cu-Ni-Sn Alloy 6 and 35 kPa vac6 and 70 kPa 0.9 and 5 psi 0.9 and 10 psiPB–PF Diaphragm 75 m (3 in)Cu-Ni-Sn Alloy 2 and 6 kPa vac2 and 10 kPa 0.3 and 0.9 psi 0.3 and 1.5 psiPB–GA (f)Heavy-Duty Helical316 ss0.5 and 200 MPa75 and 30 000 psiPC 3 to 15 PC 3 to 27Receiver (Bellows)Brass20 to 100 kPa Range—3 to 15 psi Range3 to 27 psi Rangea.All elements except Code PC have zero-based ranges. Therefore, the lower range values are zero and the upper range valuesare as listed.b.To convert kPa to bar or kg/cm2, divide kPa value by 100. To convert MPa to bar or kg/cm2, multiply MPa value by 10.c.To convert psi to inH2O, multiply psi value by 27.73. To convert psi to inHg, multiply psi value by 2.036.d.Replacement element not calibrated.e.K-Monel elements comply with NACE Standard MR-01-75.f.Element extends through back of case. Replacement element not recommended. Return instrument to Global CustomerSupport.PSS 3-1B3 A Page 6MODEL CODEMODEL CODEDescription Model Indicating Controller43AP MountingField (Pipe or Y oke, as specified in complete element code)– F Panel or Surface– P Control On-OffA1Proportional 4 to 400%A2Proportional plus Derivative 0.05 to 50 minutesA3Proportional plus Integral (Reset) 0.01 to 50 minutes per repeat A4Proportional plus Integral plus Derivative A5Differential Gap 1 to 100%A7Automatic ShutdownA8Output Signal and Gauge20 to 100 kPa signal; 200 kPa gauge 53 to 15 psi signal; 30 psi gauge 20.2 to 1.0 bar signal; 2 bar gauge60.2 to 1.0 kg/cm 2 signal; 2 kg/cm 2 gauge4Automatic Manual Internal Transfer Switching NoneN Bumpless with 2-position switch, balance gauge, regulator C 2-position nozzle seal switch for manual controlD Optional SuffixRemote Pneumatic Set Point (Not available with pressure elementCodes P A–CA, P A–CC, PB–GA, T ype 70 Contacts, or AS Reference “BA TCH-H”.)– PElements Available (Refer to element specifications tables) (a)a.The 43AP also uses the /E Electronic Servo Element. Refer to PSS 3-1B3 B.Differential pressure, T ype 37 Diaphragm (43AP–F only)/DE–A, –B Absolute pressure, bellows/P A–CA Absolute pressure, double spiral /P A–MA Pressure, helical /–PB–AA, –AM Pressure, spiral /–PB–BA, –BM Pressure, bellows /–PB–CA, –CC Pressure, diaphragm/–PB–DF , –PF Pressure, heavy-duty helical (43AP–F only)/–PB–GA Pressure receiver, bellows/–PCT emperature, Filled Thermal System/–T A–1A, –2A,–2B, –3BExamples: 43AP–P A12N–P/PB–AA; 43AP–FA25C/DE–EOPTIONAL FEATURESPSS 3-1B3 APage 7 OPTIONAL FEATURESBumplessAutomatic-Manual T ransferStation Consists of precision balance tube, regulator, and 2-position switch locatedwithin enclosure. A simple 2-step procedure provides bumpless transferbetween automatic and manual control. A shutoff valve is supplied to allowautomatic controller and relay to be serviced while retaining manual control.See ModelCodeNozzle Seal Switchfor Manual Control An internally mounted 2-position switch provides a simple and inexpensivemethod of achieving manual control. In the manual position, the switch sealsthe nozzle circuit and the output can be changed by varying the controllersupply pressure with an external regulator.See ModelCodeRemote Pneumatic Set Point Integral AirSupply Set Enables the set point to be positioned from a remote source using a standardpneumatic signal. Available over the full span or part of the span.Fixed or adjustable combination pressure regulator and filter with 50mm (2 in)gauge mounted and piped to controllers. Fixed pressure regulator availablewithout gauge. Maximum input 1 MPa, 150 psi, or 10 bar or kg/cm2. NOTE:Not available with panel mounted controllers.See ModelCodeIASType 70 Electric Alarm Contacts This option comprises a rotor unit with up to 5 contacts. Relays are located in aseparate external sheet metal housing. One relay may be supplied to energizeon increasing or decreasing measurement, as specified. Or two relays may be provided, one energizing on increasing measurement and one on decreasing measurement. Relay contacts rating (noninductive load): 5 A at 120 V ac, 2 Aat 240 V ac, and 5 A at 24V ac or dc. Electrical classification: ordinarylocations.C–T/70Control Valve Mounting A 43AP Controller without elements extending from back of case may beassembled on a control valve fitted with a P50 or P110 Actuator at the factory.CVMExternal Connection to IntegralBellows Used when an external feedback signal must be applied to prevent integralcircuit saturation.ECRBExternal Set Point A knob is fitted on door and engages set point adjustment mechanism.ESPHigh “Batch”Modification For processes involving discontinuous control, the integral (reset) function ismodified to prevent overshoot and to initiate immediate corrective action whencontrol is resumed.BA TCH-HGas Tight Case Special case machining and a gasketed 1/2 NPT vent connection permitsoperation of the controller with clean, noncorrosive process gas.GTCExternal Phenolic Nameplate Laminated plastic nameplate 38 X 76 mm (1.5 X 3 in) with white characters ona black background. Maximum of 5 lines with 28characters or spaces 3 mm(0.13 in) high, or 24 characters or spaces 4 mm (0.16 in) high per line.N/PGlass Window inDoor Shatterproof glass window used in areas where abrasive dust can causescratching of standard polycarbonate window under frequent wiping conditions.GIDStainless Steel DataPlate A stainless steel data plate 36 X 40 mm (1.4 X 1.6 in). Maximum of 4lines with11 characters or spaces per line.SCTCustomer T ag Stainless steel tag attached to instrument for customer tag data that doesn't fiton data plate. There can be a maximum of 10 lines of data with 40 charactersper line.MTSPSS 3-1B3 APage 8OPTIONAL FEATURES Tamper-Proof Knob The door knob is removed to prevent unauthorized access to controladjustments. The door is opened with a specially shaped knob.TPKExternal Subpanel forAutomatic-Manual Switching For use only with controllers not having internal transfer switching. Consists ofpressure regulator, nominal 40 mm (1.5 in) gauge, and 2-position transferswitch completely piped and assembled to external subpanel mounted tobottom surface of enclosure. Subpanel is finished in gray. The 1 in AS Code isfor Control Codes A1, A2, A3, A7, and A8. The 2 in AS Code is for ControlCodes A4 and A5. The S in AS Code is gauge in kPa, the E is psi, and the M iskg/cm2.SD–1SSD–1ESD–1MSD–2DSD–2ESD–2Ma.AS is Auxiliary Specification.OPTIONAL FEATURES (CONTINUED)DIMENSIONS - NOMINALPSS 3-1B3 APage 9 DIMENSIONS - NOMINALPSS 3-1B3 APage 10NOTESNOTESPSS 3-1B3 APage 11NOTESInvensys Systems, Inc.10900 Equity DriveHouston, TX 77041United States of America Global Customer Support Inside U.S.:1-866-746-6477Outside U.S.:1-508-549-2424Website: Copyright 1977-2015 Invensys Systems, Inc. All rights reserved.Invensys and Foxboro are trademarks of Invensys Limited, its subsidiaries, and affiliates. All othertrademarks are the property of their respectiveowners.Invensys is now part of Schneider Electric.0715PSS 3-1B3 APage 12ORDERING INSTRUCTIONSOTHER FOXBORO PRODUCTS1. Model Number2. Mounting3. Element T ype, Material, and Range4. Measurement Range5. Measurement Connection6. Scale Range7. Supply Pressure and Output Signal8. Controller Action9. Optional Features 10. T ag and ApplicationThe Foxboro product lines offer a broad range of measurement and instrument products, including solutions for pressure, flow, analytical, temperature, positioning, controlling, and recording.For a list of these offerings, visit our web site at:。
SL2.1A-Datasheet-V1
USB2.0 HUB控制器集成电路USB 2.0 HIGH SPEED 4-PORT HUB CONTROLLERSL2.1A数据手册Data Sheet内容目录第一章管脚分配 (3)1.1 SL2.1A管脚图 (3)1.2 SL2.1A管脚定义 (4)第二章 功能叙述 (5)2.1综述 (5)2.2充电支持 (5)第三章电气特性 (5)3.1极限工作条件 (5)3.2工作范围 (6)3.3直流电特性 (6)3.4HS/FS/LS电气特性 (6)3.5ESD特性 (6)附录一封装 (7)表格目录表格1: 最大额定值 (5)表格2: 工作范围 (6)表格3: 直流电特性 (7)插图目录图1：SL2.1A 管脚图 (3)图 2：附录 封装图 ................................................................................... .7SL Chip ShenZhen Co.,LtdSL2.1A 管脚图SL Chip ShenZhen Co.,Ltd 第一章 管脚分配图 1：SL2.1A 管脚图SL2.1A管脚定义管脚名称16Die IO类型定义Pin#DM4 1 B 下行口4的USB DM信号DP4 2 B 下行口4的USB DP信号DM3 3 B 下行口3的USB DM信号DP3 4 B 下行口3的USB DP信号DM2 5 B 下行口2的USB DM信号DP2 6 B 下行口2的USB DP信号DM1 7 B 下行口1的USB DM信号DP1 8 B 下行口1的USB DP信号DM 9 B 上行口的USB DM信号DP 10 B 上行口的USB DP信号VDD5 11 P 5v输入GND 12 P 芯片地VDD33 13 P 内部3.3vVDD18 14 P 内部1.8vXOUT 15 O晶振PADXIN 16 I注释：O，输出；I 输入；B 双向；P 电源/接地；SL Chip ShenZhen Co.,Ltd第二章 功能叙述2.1综述SL2.1A是一颗高集成度,高性能,低功耗的USB2.0集线器主控芯片；该芯片采用STT技术,单电源供电方式，芯片供电电压为5v, 内部集成5V转3.3V,只需在外部电源添加滤波电容；芯片自带复位电路，低功耗技术让他更加出众。
瑞特拉电子产品购买指南说明书
241For additional technical information visit Metric measurements for this product are exact, imperial measurements are rounded to the nearest whole numberUseful Cooling Capacity: 2400 - 5794 BTU (703 - 1697 W)Part No. with basic controller 3303.1042)3303.1142)3304.1043304.1143304.1443305.1043305.1143305.144Part No. with comfort controller 3303.5042)3303.5142)3304.5043304.5143304.5443305.5043305.5143305.544Voltage V , Hz230, 50/60115, 60230, 50/60115, 60400, 50/ 460, 60, 3~230, 50/60115, 60400, 50/ 460, 60, 3~Dimensions inches (mm)H x W x D24 x 11 x 12 (620 x 285 x 298)40 x 16 x 14 (1020 x 405 x 358)Useful cooling capacity Q KBTU (W)T i 131 T a 1312400 (703)3916 (1147)5794 (1697)Useful cooling capacity Q K to DIN 3168 BTU (W)T i 95 T a 951708/2083(500/610)1708 (500)3415/3620 (1000/1060)5123/5157 (1500/1510)T i 95 T a 122956/1195(280/350)956 (280)2698/2869 (790/840)4201/4269 (1230/1250)Rated current maximum 2.6/2.6 A 5.7 A 5.4/5.0 A 10.6/11.1 A 2.8/2.9 A 6.0/6.5 A 12.1/13.6 A 2.6/2.9 A Starting current 5.1/6.4 A 11.5 A 12.0/14.0 A 26.0/28.0 A 11.5/12.7 A 22.0/24.0 A 42.0/46.0 A 12.2/11.3 A Pre-fuse T 10.0 A 10.0 A 10.0 A 16.0 A 10.0 A 1)16.0 A 20.0 A 10.0 A 1)Power consumption Pel toDIN 3168T i 95 T a 95360/380 W 470 W 700/650 W 725/680 W 580/550 W 850/1000 W 880/1050 W 800/980 W T i 95 T a 122420/390 W500 W 750/710 W 780/750 W 660/680 W 1000/1160 W 1040/1200 W 960/1150 W Cooling coefficient j =Q K /PelT i 95 T a 95 1.4 1.7 1.8 1.7 1.9Refrigerant R134a, 6.0 oz (170 g)R134a, 17.6 oz (500 g)R134a, 21.1 oz (600 g)Maximum allowable operating pressure 406 psi (28 bar)363 psi (25 bar)Temperature and setting range Comfort Controller - 68 to 131° F (+20 to +55° C) / Basic Controller - 86 to 131° F (+30 to +55° C)Environmental ratings UL Type 4X (IP 66)Duty cycle 100%Type of connection Plug-in terminal strip Weight lb (kg)55.1 (25)108.2 (49)119.0 (54)110.2 (50)112.4 (51)123.5 (56)114.6 (52)Material Type 304 stainless steelAir displacement offans External circuit 203 cfm (345 m 3/h)530 cfm (900 m 3/h)530 cfm (900 m 3/h)Internal circuit 182 cfm (310 m 3/h)353 cfm (600 m 3/h)471 cfm (800 m 3/h)Temperature control Basic or comfort controller (factory setting 95° F [+35° C])Accessories PU Page Door-operated switch 14127.010–Master/slave cable for comfortcontroller13124.100–3124.100267RiDiag II including cables for comfortcontroller13159.100267Interface card for comfort controller 13124.200268Condensate hose 13301.6103301.6122731) Motor circuit breaker. 2)Internal condensate evaporator not included. Special voltages and technical modifications available on request.Wallmounted UL T ype 4X Air ConditionerCon guration:Fully wired ready for connection, including drilling template and assembly parts. With nano-coated condenser and integrated condensate evaporator.Protection Ratings:UL and cUL recognized, CSA UL Type 4XUL file: SA8250 Material:Type 304 stainless steel Note:Air conditioner with comfortcontroller may be integrated into a monitoring system with an optional interface card 3124.20 (RS 232, RS 485, RS 422 and PLC interface). See page 268. Made in the USA.000C o u r t e s y o f C M A /F l o d y n e /H y d r a d y n e ŀ M o t i o n C o n t r o l ŀ H y d r a u l i c ŀ P n e u m a t i c ŀ E l e c t r i c a l ŀ M e c h a n i c a l ŀ (800) 426-5480 ŀ w w w .c m a f h .c o242For additional technical information visit Metric measurements for this product are exact, imperial measurements are rounded to the nearest whole numberUseful Cooling Capacity: 8706 - 10525 BTU (2550 - 3083 W)Part No. with basic controller 3328.1043328.1143328.1443329.1043329.1143329.144Part No. with comfort controller 3328.5043328.5143328.5443329.5043329.5143329.544Rated operating voltage V , Hz 230, 50/60115, 50/60400, 50/460, 60, 3~230, 50/60115, 50/60400, 50/460, 60, 3~Dimensions inches (mm)H x W x D 65 x 16 x 15 (1650 x 405 x 388)Useful cooling capacity Q K BTU (W)T i 131 T a 1318706 (2550)10525 (3083)Useful cooling capacity Q K to DIN 3168 BTU (W)T i 95 T a 956860/8025 (2000/2350)8538/9392 (2500/2750)T i 95 T a 1224952/5772 (1450/1690)5464/5977 (1600/1750)Rated current max. 7.5 A/9.1 A 14.7 A/17.3 A 2.8 A/3.3 A 8.6 A/10.6 A 17.0 A/22.0 A 3.7 A/3.8 A Start-up current 22.0 A/26.0 A36.0 A/39.0 A6.8 A/7.8 A 21.0 A/21.0 A44.0 A/42.0 A6.8 A/7.6 A Pre-fuse T16.0 A25.0 A 10.0A/10.0 A 1)16.0 A 25.0 A 10.0 A/10.0 A 1)Power consumption Pel to DIN 3168 T i 95 T a 951025/1200 W 1085/1250 W 1050/1275 W 1450/1675 W 1500/1725 W 1425/1625 W T i 95 T a 1221250/1350 W1300/1410 W1275/1525 W1625/2000 W1675/2065 W1675/1975 WCooling coefficient j = Q K /Pel T i 95 T a 951.72.31.92.0RefrigerantR134a, 31.7 oz (900 g)Maximum allowable operating pressure 406 psi (28 bar)Temperature and setting range Comfort Controller - 68 to 131° F (+20 to +55° C) / Basic Controller - 86 to 131° F (+30 to +55° C)Protection rating UL Type 4X (IP 66)Duty cycle 100%Type of connection Plug-in terminal stripWeight lb (kg)176.4 (80)191.8 (87)176.4 (80)183.0 (83)198.4 (90)183.0 (83)MaterialType 304 stainless steelAir displacement of fans External circuit 377 cfm (640 m 3/h)418 cfm (710 m 3/h)Internal circuit324 cfm (550 m 3/h)377 cfm (640 m 3/h)Temperature control Basic or comfort controller (factory setting 95° F [+35° C])Accessories PU Page Door-operated switch14127.010–Master/slave cable for comfort controller13124.100267RiDiag II including cables for comfort controller 13159.100267Interface card for comfort controller 13124.200268Condensate hose13301.6122731)Motor circuit breaker. Special voltages available on request. We reserve the right to make technical modifications.Wallmounted UL T ype 4X Air ConditionerCon guration:Fully wired ready for connection, including drilling template and assembly parts. With nano-coated condenser and integrated condensate evaporator.Protection Ratings: UL and cUL recognized UL Type 4X UL file: SA8250Material:Type 304 stainless steelNote:Air conditioner with comfortcontroller may be integrated into a monitoring system with an optional interface card 3124.200(RS 232, RS 485, RS 422 and PLC interface). See page 268. Made in the USA.C o u r t e s y o f C M A /F l o d y n e /H y d r a d y n e ŀ M o t i o n C o n t r o l ŀ H y d r a u l i c ŀ P n e u m a t i c ŀ E l e c t r i c a l ŀ M e c h a n i c a l ŀ (800) 426-5480 ŀ w w w .c m a f h .c o。
波仕Power Tools GBH Professional 2-23 S 2-23 E 2
1 619 P09 070 | (12.10.10)Bosch Power Tools2 |B o sc h h a m m e B o s c h h a m m e r B o s c h h a m m e r B 123456789101111X1109GBH 2-23 RE Professional 1112OBJ_BUCH-1282-002.book Page 2 Tuesday, October 12, 2010 3:33 PMB oB os c h h a m m e r B o 31194 | 中文1 619 P09 070 | (12.10.10)Bosch Power Tools安全规章电动工具通用安全警告阅读所有警告和所有说明! 不遵照以下警告和说明会导致电击、着火和／或严重伤害。
保存所有警告和说明书以备查阅。
在所有下列的警告中术语 "电动工具" 指市电驱动（有线）电动工具或电池驱动（无线）电动工具。
1)工作场地的安全a)保持工作场地清洁和明亮。
混乱和黑暗的场地会引发事故。
b)不要在易爆环境，如有易燃液体、气体或粉尘的环境下操作电动工具。
电动工具产生的火花会点燃粉尘或气体。
c)让儿童和旁观者离开后操作电动工具。
注意力不集中会使你失去对工具的控制。
2)电气安全a)电动工具插头必须与插座相配。
绝不能以任何方式改装插头。
需接地的电动工具不能使用任何转换插头。
未经改装的插头和相配的插座将减少电击危险。
b)避免人体接触接地表面，如管道、散热片和冰箱。
如果你身体接地会增加电击危险。
c)不得将电动工具暴露在雨中或潮湿环境中。
水进入电动工具将增加电击危险。
d)不得滥用电线。
绝不能用电线搬运、拉动电动工具或拔出其插头。
使电线远离热源、油、锐边或运动部件。
受损或缠绕的软线会增加电击危险。
e)当在户外使用电动工具时，使用适合户外使用的外接软线。
适合户外使用的软线将减少电击危险。
SS56
SYMBOL VRRM VRMS VDC I(AV)
SS52 20 14 20
SS53 30 21 30
SS54 40 28 40
SS55 50 35 50 5.0
SS56 60 42 60
SS58 80 56 80
SS510 100 70 100
UNIT V V V A
IFSM VF IR CJ RθJA TJ TSTG 500 15 0.45 0.55 0.6
.060(1.52) .030(0.76)
.320(8.13) .305(7.75)
.008(.203) .002(.051)
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25℃ ambient temperature unless otherwise specified. Single phase, half wave ,60Hz, resistive or inductive load. For capacitive load, derate current by 20%
SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.375″（9.5mm) LEAD LENGTHS
FIG. 2 – MAXIMUM NON-REPETITIVE SURGE CURRENT 200
150
100
50
PULSE WIDTH 8.3ms SINGLE HALF-SINE-WAVE (JEDEC METHOD)
FIG.2-TYPICAL REVER CHARACTERISTICS 20 INSTANTANEOUS REVERSE CURRENT(mA) 10
DA230_datasheet
Termination: L = RoHS compliant tin-silver over tin over nickel over phos bronze. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
series and with the secondary windings shorted. 5. Based on Bsat of the core at 25°C and number of turns on winding 4-3. 6. Calculated output power based on 150 kHz operating frequency. Power
Document 550
SMT Power Transformers ForAnalogDevicesADM2485 Isolated RS-485 Transceiver
• Developed specifically for Analog Devices ADM2485 Isolated RS-485 Transceiver for stepping up 5 V or 3.3 V to 6 V.
Dot indicates pin 1
4
8
1 0.394 max 10,00
4
0.235 max 5,97
0.028 0,70
4
DA230X-AL CCIXXXX
0.475 max 12,07
0.319 ±0.004 8,1 ±0,1
8 Pri 3 2
7 Sey windings and secondary windings to be connected in series on the PC board.
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
A Customer Driven, Better and Faster Product Development Advanced Green Belt Training
1
In today’s fast-paced global economy, time to market constraints are demanding that companies produce their products more quickly and with higher quality. This has driven a shift from inspection based quality where defects are found and repaired… … to design based quality where defects are prevented from ever occurring. Through Quality Function Deployment, Design of Experiments, detailed Failure Mode Analyses, and other quality tools, zero defect or 3ppm defect levels are being achieved by design. That is what Design for Six Sigma (DFSSest our Six Sigma efforts where it offers the highest leverage against the cost of poor quality
Quality Leverage
Here… 1000:1 PRODUCT 100:1 PLANNING PRODUCT 10:1 ENGINEERING PROCESS ENGINEERING
Costly to fix problem
Design For Six Sigma aims at designing 6 sigma quality into a new product or service right from the start… … When cost of change is lowest and design alternatives are still available. Design for Six Sigma can be seen as a subset of Six Sigma focusing on preventing problems, instead of just fixing them, such as Six Sigma DMAIC.
Six Sigma Green Belt 2007 - English
© 2006 Rath & Strong, limited rights for Schneider Electric - internal use only
4
Introduction
Six Sigma Green Belt 2007 - English
Six Sigma Green Belt 2007 - English
© 2006 Rath & Strong, limited rights for Schneider Electric - internal use only
6
Cross Functional Engineering and Optimal Design To Customer
© 2006 Rath & Strong, limited rights for Schneider Electric - internal use only
5
Design for Six Sigma Supports You On…
The primary emphasis in DFSS is Customer Focus and Quality. Its Essence is to ensure design quality and predictability during the early design phases. The approach employs a structured integrated design methodology and a comprehensive set of robust tools to drive product quality, innovation, faster time to market, and lower costs for product, process and service design.
Six Sigma Green Belt 2007 - English © 2006 Rath & Strong, limited rights for Schneider Electric - internal use only 3
Agenda
Introduction The Reasons of A Deep Change Successful Product Development Design for Six Sigma Core Modules
Manufacturing process improvement is often the result of poor product development
… Early investments of time and effort pay off grandly in getting the product Right First Time…
CTQ Tree
Process Management supports and maintains the projects’ solutions once they are fully implemented. It is a source for new improvement and design projects.
Bob Galvin, CEO of Motorola stated that…
“ If I would start six sigma again, I would focus on product development rather than manufacturing.”
Galvin’s view is that mfg. process improvement is often the result of poor product development.
what the customer wanted
© 2006 Rath & Strong, limited rights for Schneider Electric - internal use only 7
Design For Six Sigma Defined
Products are created by processes. Making the processes work will help make the product work.
Six Sigma Green Belt 2007 - English © 2006 Rath & Strong, limited rights for Schneider Electric - internal use only 10
Three Dimensions of Six Sigma
Lean Six Sigma DMAIC incrementally improves existing processes by systematically removing root causes for variation and increasing process velocity by eliminating waste and creating a continuous flow of value-adding activities pulled by the customer
DFSS focuses here
Planning
High Returns Easy to fix problem
Development
Running Production
Easy to see Low Returns
Difficult to see / predict
Currently, 45% of the Issues faced by our Customer are coming from the Offer Creation Process.
what marketing suggested
what management approved
as designed by engineering
what was manufactured
Six Sigma Green Belt 2007 - English
as services installed it
Core Process Matrix
Design For Six Sigma
QFD Design For Six Sigma is used when a new a product or service is needed or an existing requires significant change so that the improvement process is inadequate.
R & D offers the highest leverage against the cost of poor quality.
Six Sigma Green Belt 2007 - English © 2006 Rath & Strong, limited rights for Schneider Electric - internal use only