Vedio204 - O204-QSL及VR单线注油器
博士安全FLEXIDOME IP 7000 VR全能防刺激球机器人视频摄像头说明书
uAesthetic vandal-resistant enclosure, suitable for indoor or outdoor applicationsuContent-based scene analysis optimizes the image processinguIntelligent noise reduction reduces bandwidth and storage requirements by up to 50%uEasy to install with auto zoom/focus SR lens, wizard and pre-configured modesThe FLEXIDOME IP 7000 VR dome camera combines intelligence with adaptive video processing to provide you with superior HD image quality. This true day/night camera provides high resolution video, tuned for 24x7 applications.The aesthetic vandal-resistant housing makes the camera suitable for indoor or outdoor installation.System overviewCompared to SD cameras, this camera offers, at no higher cost, motorized autofocus, higher resolution,better sensitivity, higher frame rates, and improved picture quality, and is still more bandwidth-efficient.Video storage costs are significantly reduced.FunctionsContent Based Imaging TechnologyContent Based Imaging Technology (CBIT) is used to radically improve image quality in all lighting conditions and to identify areas for enhancedprocessing. The camera examines the scene using Intelligent Video Analysis (IVA) and provides feedback to re-tune the image processing. This provides better detail in the areas that matter and better all-roundperformance. With IVA, the Intelligent Auto Exposure technology, for example, allows you to view moving objects in bright and dark areas of a scene.Intelligent Dynamic Noise Reduction reduces bandwidth and storage requirementsThe camera uses Intelligent Dynamic Noise Reduction which actively analyzes the contents of a scene and reduces noise artifacts accordingly.The low-noise image and the efficient H.264compression technology provide clear images while reducing bandwidth and storage by up to 50%compared to other H.264 cameras. This results in reduced-bandwidth streams that still retain a high image quality and smooth motion. The cameraprovides the most usable image possible by cleverly optimizing the detail-to-bandwidth ratio.Area-based encodingArea-based encoding is another feature which reduces bandwidth. Compression parameters for up to eight user-definable regions can be set. This allowsuninteresting regions to be highly compressed, leaving more bandwidth for important parts of the scene.The average typical optimized bandwidth in kbits/s for various image rates is shown in the table:Multiple streamsThe innovative multi-streaming feature delivers various H.264 streams together with an M‑JPEG stream. These streams facilitate bandwidth-efficient viewing and recording as well as integration with third-party video management systems.An upright mode can be selected for the second stream. In this mode an image of 400 x 720 (9:16 aspect ratio) is cropped from the full sensor image. When the scene to be monitored is suitable to this mode, the bandwidth and storage requirements are reduced.Regions of interest and E-PTZRegions of Interest (ROI) can be user defined. The remote E-PTZ (Electronic Pan, Tilt and Zoom) controls allow you to select specific areas of the parent image. These regions produce separate streams for remote viewing and recording. These streams, together with the main stream, allow the operator to separately monitor the most interesting part of a scene while still retaining situational awareness.With IVA, Intelligent Tracking can follow objects within the defined regions of interest. Intelligent Tracking can autonomously detect and track moving objects or the user can click on an object which the tracker will then follow.Flexible lens choiceThe camera comes with a choice of AVF (Automatic Varifocal) lenses for easy installation. These SR (Super Resolution) lenses have an advanced iris design to ensure that the high resolution HD sensor produces the sharpest image possible, even in the corners. Simple set-upThe camera has a very intuitive user interface that allows fast and easy configuration. Configurable scene modes are provided with the best settings for a variety of applications.•Indoor – general day-to-night changes in an indoorenvironment without sun highlights or street lighting effects.•Outdoor – general day-to-night changes in an outdoor environment with sun highlights and street lightingeffects.•Traffic – for monitoring traffic movement on roads or parking lots. It can also be used in industrialapplications where fast moving objects are to bemonitored. Motion artifacts are minimized.•Night-optimized – optimized for details in low lightenvironments.•Intelligent AE – optimized for scenes with fluctuating front and back light caused by sunlight or otherilluminated objects in the scene.•Vibrant – enhanced contrast, sharpness andsaturation.•Low bit rate – reduces bandwidth requirements.•Sports and gaming – high-speed capture, andimproved color rendition and sharpness.•Retail – improved color rendition and sharpness with reduced bandwidth requirements.Storage managementRecording management can be controlled by the Bosch Video Recording Manager (VRM) or the camera can use iSCSI targets directly without any recording software.Edge recordingInsert a memory card into the card slot to store up to 2 TB of local alarm recording. Pre-alarm recording in RAM reduces recording bandwidth on the network, and extends the effective life of the memory card. Video analyticsWith built-in video content analysis, the camera reinforces the Intelligence-at-the-Edge concept where edge devices become increasingly intelligent. The MOTION+ video motion analysis system that is built into all camera versions is the perfect solution for applications where standard video content analysis features are required.The IVA version of the camera uses the latest generation of the Bosch Intelligent Video Analysis (IVA) software. This IVA system is the guard-assistant system of choice when reliable indoor or outdoor video analytics is needed. The state-of-the-art system reliably detects, tracks, and analyzes moving objects while suppressing unwanted alarms from spurious sources in the image.The face detection feature detects faces in the scene and forwards a high quality JPEG image of the best shot of each face when the face disappears from the scene.Retrospective forensic search capabilities are available remotely from the web browser or theBosch Video Client.Cloud-based servicesThe camera supports time-based or alarm-based JPEG posting to four different accounts. These accounts can address FTP servers or cloud-based storage facilities (for example, Dropbox). Video clips or JPEG images can also be exported to these accounts.Alarms can be set up to trigger an e-mail or SMS notification so you are always aware of abnormal events.Access securityPassword protection with three levels and 802.1x authentication is supported. To secure Web browser access, use HTTPS with a SSL certificate stored in thecamera. The video and audio communication channels can be independently AES encrypted with 128-bit keys by installing the optional encryption site license. Complete viewing softwareThere are many ways to access the camera’s features: using a web browser, with the Bosch Video Management System, with the free-of-chargeBosch Video Client, with the video security mobile app, or via third-party software.Video security AppThe Bosch video security mobile App has been developed to enable Anywhere access to HD surveillance images allowing you to view live images from any location. The App is designed to give you complete control of all your cameras, from panning and tilting to zoom and focus functions. It’s like taking your control room with you.This App, together with the separately available Bosch transcoder, will allow you to fully utilize our dynamic transcoding features so you can play back images even over low-bandwidth connections.System integrationThe camera conforms to the ONVIF Profile S specification. Compliance with this standard guarantees interoperability between network video products regardless of manufacturer.Third-party integrators can easily access the internal feature set of the camera for integration into large projects. Visit the Bosch Integration Partner Program (IPP) website () for more information.Easy installationPower for the camera can be supplied via a Power-over-Ethernet compliant network cable connection. With this configuration, only a single cable connection is required to view, power, and control the camera. Using PoE makes installation easier and more cost-effective, as cameras do not require a local power source.The camera can also be supplied with power from+12 VDC/24 VAC power supplies. To increase system reliability, the camera can be simultaneously connected to both PoE and +12 VDC/24 VAC supplies. Additionally, uninterruptible power supplies (UPS) can be used, which will allow continuous operation, even during a power failure.The automatic zoom/focus lens wizard makes it easy for an installer to accurately zoom and focus the camera for both day and night operation. The wizard is activated from the PC or from the on-board camera push button making it easy to choose the workflow that suits best.The AVF (Automatic Varifocal) feature means that the zoom can be changed without opening the camera. The automatic motorized zoom/focus adjustment with 1:1 pixel mapping ensures the camera is always accurately focused.Hybrid modeAn analog video output enables the camera to operate in hybrid mode. This mode provides simultaneous high resolution HD video streaming and an analog video output via a BNC connector. The hybrid functionality offers an easy migration path from legacy CCTV to a modern IP-based system.Aesthetic vandal resistant designThe compact aesthetic design is suitable for installations where housing size and appearance are important. The cast-aluminum housing, polycarbonate window, and hardened inner liner can withstand the equivalent of 55 kg (120 lbs) of force (IK10). The camera is protected against water and dust to IP 66 (NEMA Type 4X) standards. Using the proprietary pan/ tilt/rotation mechanism, installers can select the exact field of view. Mounting options are numerous, including surface, wall, corner, and suspended-ceiling mounting.Typical applications•Retail, banks•Stadiums•Schools•Care facilities•Traffic monitoring (air, land and sea)•Hotels, bars and nightclubs•Commercial and government buildings•City surveillance and safety•Border controlHD standardsComplies with the SMPTE 274M-2008 Standard in:–Resolution: 1920x1080–Scan: Progressive–Color representation: complies with ITU-R BT.709–Aspect ratio: 16:9–Frame rate: 25 and 30 frames/sComplies with the 296M-2001 Standard in:–Resolution: 1280x720–Scan: Progressive–Color representation: complies with ITU-R BT.709–Aspect ratio: 16:9–Frame rate: 25 and 30 frames/sStandards* Chapters 7 and 8 (mains voltage supply requirement) are not applicable to the camera. However, if the system in which this camera is used needs to comply with this standard, then any power supplies used must comply with this standard.Installation/configuration notesDimensions flush mountingmm (in) Dimensions surface mountingØ158 (6.22)mm (i n)VDA-WMT-DOME –Pendant Wall Mount205 (8.07)mm (in)247(9.71) LTC 9213/01 Pole Mount AdapterHolemm(in.)mm (in)17(4.19)Parts includedTechnical specificationsSensitivity – (3200K, reflectivity 89%, 1/60, 30IRE)Lens 3 - 9 mm (F1.2)Resolutions (H x V)Ordering informationFLEXIDOME IP 7000 VRHigh-performance IP dome camera for HD surveillance. 1080p30; Hybrid; IP66; IK10; IDNR; ROI; H.264 quad-streaming; cloud services; free viewing Apps; 3 to9 mm SR lens; MOTION+Order number NIN-832-V03PFLEXIDOME IP 7000 VRHigh-performance IP dome camera for HD surveillance. 1080p30; Hybrid; IP66; IK10; IDNR; IAE; ROI; H.264 quad-streaming; cloud services; free viewing Apps; 3 to 9 mm SR lens; IVAOrder number NIN-832-V03IPFLEXIDOME IP 7000 VRHigh-performance IP dome camera for HD surveillance. 1080p30; Hybrid; IP66; IK10; IDNR; ROI; H.264 quad-streaming; cloud services; free viewing Apps; 3 to9 mm SR lens; MOTION+; SMBOrder number NIN-832-V03PSFLEXIDOME IP 7000 VRHigh-performance IP dome camera for HD surveillance. 1080p30; Hybrid; IP66; IK10; IDNR; IAE; ROI; H.264 quad-streaming; cloud services; free viewing Apps; 3 to 9 mm SR lens; IVA; SMBOrder number NIN-832-V03IPSFLEXIDOME IP 7000 VRHigh-performance IP dome camera for HD surveillance. 1080p30; Hybrid; IP66; IK10; IDNR; ROI; H.264 quad-streaming; cloud services; free viewing Apps; 10 to23 mm SR lens; MOTION+Order number NIN-832-V10PFLEXIDOME IP 7000 VRHigh-performance IP dome camera for HD surveillance. 1080p30; Hybrid; IP66; IK10; IDNR; IAE; ROI; H.264 quad-streaming; cloud services; free viewing Apps; 10 to 23 mm SR lens; IVAOrder number NIN-832-V10IPFLEXIDOME IP 7000 VRHigh-performance IP dome camera for HD surveillance. 1080p30; Hybrid; IP66; IK10; IDNR; ROI; H.264 quad-streaming; cloud services; free viewing Apps; 10 to23 mm SR lens; MOTION+; SMBOrder number NIN-832-V10PS FLEXIDOME IP 7000 VRHigh-performance IP dome camera for HD surveillance. 1080p30; Hybrid; IP66; IK10; IDNR; IAE; ROI; H.264 quad-streaming; cloud services; free viewing Apps; 10 to 23 mm SR lens; IVA; SMBOrder number NIN-832-V10IPSAccessoriesVDA-WMT-DOME Wall Pendant Mount BracketWall pendant mount bracket for FlexiDome cameras Order number VDA-WMT-DOMEVDA-CMT-DOME Corner Mount BracketCorner mount bracket for FlexiDome camerasOrder number VDA-CMT-DOMEVDA-PMT-DOME Pendant Pipe Mount Bracket Pendant pipe mount bracket for FlexiDome cameras Order number VDA-PMT-DOMELTC 9213/01 Pole Mount AdapterFlexible pole mount adapter for camera mounts (use together with the appropriate wall mount adapter). Max. 9 kg (20 lb); 3 to 15 inch diameter pole; stainless steel strapsOrder number LTC 9213/01VDA-PLEN-DOME In-ceiling Housing for Plenums Kit FLEXIDOME in-ceiling housing installation kit (plenum-rated) for various FLEXIDOME camerasOrder number VDA-PLEN-DOMEVGA-IC-SP In-ceiling Support KitSuspended ceiling support kit for FLEXIDOME VR cameras (requires VDA-PLEN-DOME kit) and AUTODOME 100/600/7000 cameras.Order number VGA-IC-SPUPA-2420-50 Power SupplyPower supply for cameras. 220 VAC, 50 Hz In; 24 VAC, 20 VA OutOrder number UPA-2420-50UPA-2430-60 Power SupplyPower supply for camera. 120 VAC, 60 Hz; 24 VAC,30 VA OutOrder number UPA-2430-60UPA-2450-50 Power Supply, 220 V, 50 HzIndoor power supply for camera. 220 VAC, 50 Hz In; 24 VAC, 50 VA OutOrder number UPA-2450-50UPA-2450-60 Power Supply, 120 V, 60 HzIndoor power supply for camera. 120 VAC, 60 Hz In; 24 VAC, 50 VA OutOrder number UPA-2450-60VDA-455TBL Tinted bubbleTinted bubble for FlexiDome seriesOrder number VDA-455TBLVDA-455CBL Clear bubbleClear Bubble for FlexiDome seriesOrder number VDA-455CBLS1460 Service/Monitor Cable2.5 mm jack to BNC video connector cable. 1 mOrder number S1460VIDEOJET XTC XF Video TranscoderHigh-performance video transcoder. H.264; CF cardslot; ROI; max resolution 1080p; 2 channelsOrder number VJT-XTCXFSurface Mount Box FLEXIDOME VRSurface Mount Box for FLEXIDOME VR CamerasOrder number VDA-455SMB-IPNIN-DMY Dummy CameraFLEXIDOME VR family dummy cameraOrder number NIN-DMYSoftware OptionsBVIP AES 128 Bit EncryptionSite licence for BVIP AES 128‑bit encryption. Enablesencrypted communication between BVIP devices andmanagement stationsOrder number MVS-FENC-AESRepresented by:Americas:Europe, Middle East, Africa:Asia-Pacific:China:America Latina:Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, New York, 14450, USA Phone: +1 800 289 0096 Fax: +1 585 223 9180***********************.com Bosch Security Systems B.V.P.O. Box 800025617 BA Eindhoven, The NetherlandsPhone: + 31 40 2577 284Fax: +31 40 2577 330******************************Robert Bosch (SEA) Pte Ltd, SecuritySystems11 Bishan Street 21Singapore 573943Phone: +65 6571 2808Fax: +65 6571 2699*****************************Bosch (Shanghai) Security Systems Ltd.203 Building, No. 333 Fuquan RoadNorth IBPChangning District, Shanghai200335 ChinaPhone +86 21 22181111Fax: +86 21 22182398Robert Bosch Ltda Security Systems DivisionVia Anhanguera, Km 98CEP 13065-900Campinas, Sao Paulo, BrazilPhone: +55 19 2103 2860Fax: +55 19 2103 2862*****************************© Bosch Security Systems 2015 | Data subject to change without notice 5288219275 | en, V15, 05. Mar 2015。
润滑设备样本
EM型电动换向阀(40MPa)/pro43.htm（第 1／3 页）2010-6-25 11:49:18EM型电动换向阀(40MPa)/pro43.htm（第 2／3 页）2010-6-25 11:49:18EM型电动换向阀(40MPa)/pro43.htm（第 3／3 页）2010-6-25 11:49:18SRB系列手动润滑泵SRB系列手动润滑泵一、使用条件 手动润滑泵是一种人力板动手柄操作排出润滑剂的小型润滑泵，可直接安装于机器的壁板或机架上。
基本型可直接与单线分配器组成手动单线集中润滑系统；基本型配上换向阀与双线分配器组成手动双线终端式集中润滑系统。
本泵适用于润滑频率较低（一般给油间隔为8小时以上），配管DN10长度不超过50米，润滑点不超过40点的单机小型设备上，作为集中润滑供送润滑剂的装置。
二、技术参数 适用介质为锥入度不低于265(25℃，150g)1/10mm的润滑脂(NLGI0#～2#)和粘度等级大于N68的润滑油，适用环境温度-10℃～40℃三、外形尺寸/pro70.htm（第 1／5 页）2010-6-25 11:50:08SRB系列手动润滑泵/pro70.htm（第 2／5 页）2010-6-25 11:50:08SRB系列手动润滑泵四、型号说明五、工作原理 手动润滑泵是人工扳动手柄，通过齿轮1带动齿轮活塞2往复运动实现给脂的。
当活塞处于图示右端极限位置时，左端油腔容积增大形成真空，于是贮油筒内的润滑剂在弹簧和活塞片的作用下从吸油口吸入活塞左端油腔内。
当活塞向左移动时，被吸入的润滑剂压入孔道Ⅰ并把滑阀4推向右端极限位置，顶开单向阀5从出油口排出，此时，活塞右端油腔容积逐渐增大，润滑剂被吸入，在活塞返回向右移动时，充满润滑剂的油腔又逐渐变小，挤压润滑剂进入孔道Ⅱ，推动滑阀4向左移动，顶开单向阀5从出油口排出，泵底部配装换向阀，扳动换向手柄至左右二极限位置可实现双线供剂。
/pro70.htm（第 3／5 页）2010-6-25 11:50:08SRB系列手动润滑泵六、操作方法单线型： 1、将回油指示器的指示杆推进。
17 Series微雾和油雾润滑器说明书
L1717 SeriesMicro-Fog and Oil-Fog Lubricators3/4", 1", 1 1/4"and 1 1/2"Port Sizes q All around (360°) visibility of the sight-feed domesimplifies installation and adjustmentq Screw-on bowl reduces maintenance timeq Can be serviced without the use of tools or removalfrom the air lineq Flow sensor design provides a nearly constant oil/airratio over a wide range of air flowsUse Micro-Fog models in applications containing one or morepoints of lubricationUse Oil-Fog models to lubricate a single tool, cylinder, or other airdriven deviceTechnical DataFluid: Compressed airMaximum pressure: 17 bar (250 psig)Operating temperature*: -20°to +80°C (0°to +175°F)*Air supply must be dry enough to avoid ice formation at temperatures below +2°C (+35°F).Start point (minimum flow required for lubricator operation):3,8dm3/s (8 scfm) at 6,3 bar (90 psig) inlet pressureTypical flow with 6,3 bar (90 psig) inlet pressure and 0,5 bar(7psig) pressure drop:1" ports: 130 dm3/s (275 scfm)Nominal reservoir size:Standard:1 litre (1 quart US)Optional:0,5 litre (1 pint US)2 litre (2 quart US)8 litre (2 gallon US)20 litre (5 gallon US)Recommended lubricants: See page N/AL.8.900.935 Materials:Body: AluminumReservoir:0,5 litre (1 pint US), 1 litre (1 quart US):Aluminum2 litre (2 quart US) and larger: Steel*Reservoir sight glass: PyrexSight-feed dome:Standard: Transparent nylonOptional: Pyrex and aluminumElastomers: Neoprene and nitrile*The 8 and 20 litre (2 and 5 gallon) steel reservoirs are ASME rated according to the ASME Pressure Vessel Code, Section VIII Ordering InformationSee Ordering Information on the followingpages.Back to Selector PageTypical Performance Characteristics (Littleton)0,30,20,10P R E S S U R E D R O Pb a r d 543210 p s i d04080120160200dm 3/s AIR FLOW80160240320400scfm*Models listed in the order table must not be located downstream of frequently cycling directional control valves. Order the optional bi-directional Oil-Fog Lubricator for use under such conditions.†Typical flow with 6,3 bar (90 psig) inlet pressure and a pressure drop of 0,5 bar (7 psig).*Only available with 3/4"and 1"port sizes.L17 Micro-Fog L17 Micro-Fog L17 Micro-Fog L17 Oil-FogMicro-Fog (Littleton) shown,Typical of Oil FogClosed bowl (Shipston)Manual drain (Shipston)Petcock drain (Littleton)2 litre (2 quart US) reservoir 8 litre (2 gallon US) reservoir 20 litre (5 gallon US) reservoirDimensions – mm (Inches)ReservoirA B ∅C 2 litre (2 quart US)(Littleton)333 (13.1)118 (4.63)137 (5.38)8 litre (2 gallon US)(Littleton)538 (21.2)159 (6.25)189 (7.44)8 litre (2 gallon US) (Shipston)*397 (15.6)252 (9.92)290 (11.4)20 litre (5 gallon US)(Littleton)614 (24.2)260 (10.3)291 (11.4)20 litre (5 gallon US)(Shipston)*509 (20.0)306 (12.1)344 (13.5)Accessories*Standard dome: 56 mm (2.22")Pyrex dome:69 mm (2.72")Wall BracketsService kit 5771-02 (Littleton), includes o-rings, seals and gaskets.Service kits L17-100M, L17-100(Shipston), include threaded cap, ball,o-rings, gaskets, screen, Micro-Fog or Oil-Fog sight dome assembly,filler plug and spring.Gasket kit (Shipston), includes o-rings, seals, gaskets and screen.Reservoir sight glass kits, include all o-rings, seals, glass, guard, and sight glass hardware.Service KitsItem TypePart Number Oil-Fog and Micro-Fog (Littleton)5771-02Service kit Micro-Fog (Shipston)L17-100M Oil-Fog (Shipston)L17-100Gasket kitMicro-Fog and Oil-Fog (Shipston)L17-GK 0,5 litre (1 pint US) (Shipston only)5872-99Reservoir sight glass kit 1 litre (1 quart US)2273-222 litre (2 quart US)2273-048 and 20 litre (2 and 5 gallon US)2274-01Replacement drainManual (Shipston)684-84Replacement drainPetcock684-016212-50, 6212-51 bracket.Use 8 mm (5/16") screws to mount bracket to wall.18-001-980, 18-001-981 brackets.Use 8 mm (5/16") screws to mount bracket to wall.18-001-056, 18-001-039 strap.Use 12 mm (1/2") screws to mount bracket to wall.*76 mm (3.00") for 18-001-056127 mm (5.00") for 18-001-039**225 mm (8.84") for 18-001-056330 mm (13.0") for18-001-039WarningThese products are intended for use in industrial compressed airsystems only. Do not use these products where pressures and temperatures can exceed those listed under ‘Technical Data’.Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult Norgren.Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid powersystems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure.System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided.System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products.。
9V NEDA 1604（Eveready 216或等效产品）电源替换
TRANSMITTER BATTERY REPLACEMENTReplacement battery - 9 volt NEDA 1604 (Eveready 216 or equivalent).The battery in the transmitter can be checked or changed by removing the front lower half of the transmitter. Refer to the directions under “accessing the code switch” for battery replacement.TO REPLACE OR ADD A SETA replacement or new transmitter or receiver may be purchased by specifying the Model Number and the RF frequency designated on the identification label. The RF frequency is set at the factory and must not be adjusted in the field. The digital code can be matched to the companion receiver or transmitter by following the above procedure.OPERATIONAL CHECKTo check operation, move back a reasonable distance (about 50 feet) and press the transmitter button. Operation should be reliable at this distance but environment and location of both the transmitter and receiver will affect the range. If the transmitter is stowed well out of sight, it may be necessary to remove it from its mounting and hold near the windshield. Try different locations and positions. If operation is still unsatisfactory, the problem maybe isolated by: 1 .Checking the door operator. If the door will not open when the wall button ispressed, the problem is likely to be the operator. If the door will open by pressing the wall button, but not when the radio control button is pressed, the problem is probably in the radios.2.Replacing the transmitter battery.If, after performing the above operational checks, the controls still do not function, they should be returned to your dealer for repair or replacement or they may be returned, postage prepaid.CAUTION: Any c hanges or m odifications in intentional or unintentional radiators which are not expressly approved by LINEAR CORPORATION could void the user’s authority to operate this equipment. This applies to intentional and unintentional radiators certified per part 15 of the F.C.C. rules and regulations.LINEAR CORPORATION2055 Corte del Nogal • Carlsbad, CA 92008(760) 438-7000Copyright © 1999 Linear Corporation214961 AInstallation Instructions GARAGE DOOR RADIO CONTROLSModel 3089 TransmitterModel 1090 ReceiverWARNING:•Disconnect power before any installation or repair•Wear safety glassesYour MULTI-CODE™ Radio Controls are designed specifically to remotely control a garage door from within an automobile and to give years of dependable service without adjustment. The transmitter/receiver combination utilizes the MULTI-CODE™ scheme which permits the selection of as many as 1024 code combinations of the owner’s personal choice. Because all radio controls are set with the even numbered switches in the “ON” position when they leave the factory, it is recommended that a different code be selected and set at the time of installation. Please refer to the “Accessing the Code Switch” section for instructions. The radio frequency (RF) portion of the controls, however, are tuned to standard frequencies and are thoroughly tested at the factory. This permits the addition or replacement of either the transmitter or the receiver by spec if ying the M odel N um ber and the R F frequency designated on the identification label. No RF adjustments are needed nor should any be attempted.RECEIVER INSTALLATIONThe receiver is designed to mount directly to the operator. It can be remotely installed if the operator terminal strip is not accessible, or if power for the receiver is not obtainable from the operator. To direct mount the receiver, simply loosen the terminal screws on the operator and insert the two-way lugs from the receiver under the screw heads along with the wall button wires), and tighten the screws (See Fig #1).Place the antenna (an 11 inch white wire) in a vertical position as far from any metal as possible.®For remote installation the receiver may be mounted near the operator head on a joist or the ceiling by using the mounting tab. Order Model 1092-06 adapter, which permits connection between the operator terminal and the two-way lugs on the receiver.Slip on connectors at one end of the adapter connect to the flat side of each spade lug on the receiver, and spade connectors at the other end connect to the operator terminal. Connect the wires as follows:(a)White wire to terminal “1” or “24v”(b)Black wire to terminal “2” or “Relay”(c)Red wire to terminal “3” or “Common” (“Radio Power”)(d) Connect push button wires to terminal “1” and “2” (See Figure #2). Where power for the radio receiver is not available from the operator order aM od el 1092-01 po w er t r an s f o r m e r ad ap t or f or c o nn e ction betw een the operator and the remote receiver.ACCESSING THE CODE SWITCHUsing a small screwdriver, pry the rectangular hatch from the receiver for access to the code switch. On the transmitter the entire front lower half of the case is removable. Grasp the front lower half of the case near the bottom on both sides and pull upward away from the transmitter, this will disengage the lower end. Then pull down ward to remove the lower cover, this will expose both the code switch and battery compartment. Set both switches to the code of your choice, being sure both are set the same since a different setting of just one switch will prevent operation. The digital code is determined by the position of 10 s m al l s w it c h es n um be r e d 1 t h rou gh 10 loc ated in the receiver and transmitter. Any combination of “on” or “off” positions can be selected by using a pencil or ball point pen. (Note: The switches are in the “on” position when the switch is depressed toward the number.) See Figure #3.Once the codes have been set, check operation and reinsert the hatches. TRANSMITTER INSTALLATIONThe transmitter is completely self contained, including battery, and can be operated while mounted in the car. It is supplied with a clip for attaching to the sun visor, if desired. If the clip is used attach to the case by sliding it into the recess provided on the back of the transmitter until the small dimples fit into the holes in the clip.CAUTION:Keep the clip flat when pushing it into position so that is doesn’t extend down into the case where it could touch the circuit board and cause damage.OPERA TOR TERMINA L24 VOLTRELA Y COMMON 1 2 3WA LL B UTTON 2 - WA Y LUGSCODE SWITCH MA TCHMOUNTING TA BA NTENNAFigure 1OPERATORTERMINALSTRIPTO WALLPUSH BUTTONSWITCHWhiteBlackRed WhiteBlackRedFigure 212345678910Figure 3OPEN。
研控科技 YKD2405PR 总线型步进驱动器 用户手册说明书
目录前言 (1)1概述 (2)1.1产品介绍 (2)1.2特性 (2)1.3应用领域 (2)1.4产品命名规则 (3)2性能指标 (4)2.1电气特性 (4)2.2使用环境 (4)3安装 (5)3.1安装尺寸 (5)3.2安装方法 (5)4 驱动器端口与接线 (6)4.1接线示意图 (6)4.2端口定义 (7)4.2.1状态指示灯 (7)4.2.2控制信号输入/输出端口 (7)4.2.3电源输入/电机输出端口 (8)4.2.4拨码开关 (8)4.2.5 MODBUS总线端口 (8)4.3输入/输出端口操作 (8)4.4拨码开关设定 (10)4.5 RS485通讯端口 (12)5适配电机 (13)5.1电机尺寸 (13)5.2技术参数 (13)5.3电机接线图 (14)6 MODBUS通讯协议 (15)6.1 MODBUS寄存器地址定义 (15)6.2 MODBUS常用功能码 (21)6.2.1读保持寄存器命令03 (21)6.2.2写单个寄存器命令06 (22)6.2.3写多个寄存器命令16 (22)6.2.4通讯错误码 (23)6.2.5应用示例 (24)7运动控制功能介绍 (26)7.1位置模式 (26)7.2速度模式 (27)7.3多段位置模式 (27)7.3.1 位置段参数介绍 (27)7.3.2 多段位控制方式 (28)7.4多段速度模式 (29)7.4.1 速度段参数介绍 (29)7.4.2 多段速度控制方式 (29)7.5回原点功能 (30)7.6运动控制命令 (31)7.6.1 启动命令（0x0027） (31)7.6.2 停止命令（0x0028） (31)7.6.3 回原点命令（0x0030） (32)8报警排除 (33)9版本修订历史 (34)10保修及售后服务 (35)10.1保修 (35)10.2售后服务 (35)前言感谢您使用本公司总线型步进驱动器。
在使用本产品前，请务必仔细阅读本手册，了解必要的安全信息、注意事项以及操作方法等。
诺基亚 SCALANCE X204-2 Managed IE 交换机数据手册说明书
Product type designation
Transmission rate Transfer rate
Interfaces / for communication / integrated Number of electrical connections ● for network components or terminal equipment Number of 10/100 Mbit/s RJ45 ports / Integrated ● with securing collar Number of 100 Mbit/s ST(BFOC) ports ● for multimode
Interfaces / others Number of electrical connections ● for signaling contact ● for power supply ● for redundant voltage supply Type of electrical connection ● for signaling contact ● for power supply
SCALANCE X204-2 10 Mbit/s, 100 Mbit/s
4 4 2
1 1 1 2-pole terminal block 4-pole terminal block
6GK5204-2BB10-2AA3 Page 1/6
07/10/2018
Subject to change without notice © Copyright Siemens
● SICLOCK support
Yes
Protocol / is supported
● NTP
欧姆龙 3G3MV 系列通用变频器 说明书
限制运转方向 (n006)................................................................ 51 阶梯形改变速度........................................................................ 51 低速运行.................................................................................... 52 调整速度设定信号.................................................................... 53 限制速度.................................................................................... 54 使用 2 套加减速时间................................................................ 54 瞬时停电复电后的自动再起动 (n081).................................... 55 平滑运行 (n023)........................................................................ 56 力矩的检测................................................................................ 56 检测频率 (n095)........................................................................ 58 避免共振 (n083 ～ n086).......................................................... 59 故障时自动复位并继续运行 (n082)........................................ 59 自由滑行中的电机无抖动运转................................................ 60 加减速暂停................................................................................ 61 使用频率表，电流表 (n066).................................................... 62 校正频率表·电流表 (n067).................................................... 62 脉冲序列信号输出作为模拟量输出 (AM-AC) 使用.............. 63 降低杂波和漏电流 (n080)........................................................ 65 STOP 键的有效 / 无效的选择 (n007) ...................................... 67 ■ 选择停止方法............................................................................ 67 选择停止方法 (n005)................................................................ 67 进行直流制动............................................................................ 68 ■ 与外部接口回路组合................................................................ 69 使用输入信号............................................................................ 69 使用多功能模拟量输入功能 (n007,n078,n079)...................... 72 使用输出信号 (n057,n058,n059) .............................................. 74 ■ 以电流指令输入设定频率........................................................ 75 ■ 用脉冲序列输入设定频率指令................................................ 77 防止电机失速............................................................................ 78 运行中失速防止的功能 UP ..................................................... 79 ■ 减少电机的速度变动................................................................ 81 补偿电机的转差 (V/f 控制模式 n002=0 的场合 ) .................. 81
LiveU LU500 User Guide V3.0
•
• • •
•
3
LiveU LU500 User Guide
Table of Contents
About This Guide ........................................................................................................ 1 Intended Audience ................................................................................................. 3 Additional Documentation .................................................................................... 3 Chapter 1: Introducing the LU500 ............................................................................ 9 Overview........................................................................................................................... 9 What’s in the LU500 Carrying Case? .........................................................................11 LiveU Central ..................................................................................................................12 Chapter 2: Getting Started ...................................................................................... 13 Step 1, Connecting the Video Camera ...................................................................14 Step 2, Powering On the LU500 Unit...........................................................................15 Charging the LU500 ...............................................................................................15 Step 3, Selecting a Channel .......................................................................................17 Virtual Groups .........................................................................................................20 Step 4, Selecting a Profile ............................................................................................22 Select a Profile ........................................................................................................22 Select the Delay .....................................................................................................23 Step 5, Selecting an Advanced Streaming Mode ................................................. 23 Step 6, Configuring WiFi ...............................................................................................27 Step 7, Going Live .........................................................................................................29 Checking Interface Quality .................................................................................30 Step 8, Shutting Down ..................................................................................................33 Chapter 3: LU500 User Interface ............................................................................. 35 LU500 Touch Screen Interface ....................................................................................36 Video Feed .....................................................................................................................37 Currently Selected Channel ......................................................................................39 Currently Selected Profile ...........................................................................................40 Connected Interfaces and Bandwidth.........................................................................40 Battery Status ................................................................................................................41 Turning Off .....................................................................................................................41 System Menu .................................................................................................................42 Selecting the LU500 Profile..........................................................................................43 Live ............................................................................................................................41 Store & Forward ......................................................................................................42 Configuration ................................................................................................................45
204中文说明书
GSW型光栅数显系统（中文液晶提示）使用说明书成都远山机电产品有限公司尊敬的用户：欢迎您使用远山机电最新开发液晶中文提示的GSW 光栅数显系统，远山机电光栅系统广泛用于铣床、磨床、镗床、线切割、车床、电火花加工设备，它的应用有助于提高生产效率、显示直观、操作方便、精度准确、重复性稳定，是模具制造业、机械加工业、精密测量仪器必不可少的装置。
本系统设置多种智能化功能，如SDM300点记忆、等分圆和椭圆、斜面加工、R的加工8个面选择、分中功能的用法，还配置了计算器，等等功能，使用起来十分方便。
应用远山机电的光栅数显系统，不须经过培训，按照中文使用说明书每步提示一看就懂。
最适合刚使用操作的新手，对于熟练的操作者更是得心应手。
要想了解有关的细节请阅读使用说明书。
安全注意事项：打开产品包装，取出箱内数显表与电子尺相接，然后插上电源检查显示是否正常。
①开箱后检查外观是否完好，若有故障应立即联系本公司销售部，切勿自行拆卸维修。
②本装置使用110V～220V，50Hz～60Hz的交流电源，电源插头是带有接地脚的三芯电源插头。
三芯电源插座地线一定要接地牢靠。
③用户不可以自行打开机壳修理，表内有高压电源以免造成人员伤害。
④本机壳是采用ABS工程塑料，不具防爆高温的环境中使用。
⑤平时不用时请关闭电源，可延长本产品使用时间。
⑥在雷雨天气时应关闭或拔掉电源线以免高压雷击电网引起表的电源电压突然猛增高而烧毁表内电源，给用户带来不必要的损失。
日常维护：①每天下班时，清洁时请关闭电源。
②用干布或毛刷擦拭数显表或电子尺防护外壳。
③不能用甲苯或乙醇清洗外壳。
④数显表外壳或显示窗的污迹可用洗衣粉和水搅匀用毛巾扭干水擦拭。
承诺：本公司产品如因用户使用操作不当造成电子尺和数显表的损坏，特别是因碰撞造成产品外观或内部损坏，或自行拆下电子尺限位，造成因超行程把尺撞坏，需本公司维修服务的，本公司要收取适当的材料费和维修费。
面板按键说明GSW-204GSW-304目录功能项目 (7)清零 (8)输入坐标 (8)公/英制显示 (8)ABS/INC坐标 (9)自动分中 (10)RI（寻找师傅零位） (11)半径/直径 (11)计算器 (11)SDM300组记忆 (12)圆周分孔 (18)椭圆分孔 (21)斜线分孔 (25)圆弧加工 (27)平滑圆弧加工 (35)斜面加工 (39)电火花加工 (42)基本参数 (45)高级用户 (46)光栅线位移传感器 (48)光栅线位移动传感器行程和安装尺寸 (51)安装示图 (52)故障分析与处理 (53)GSW-中文提示光栅数显表，中文辅助显示智能表，采用高科技软件电子技术，功能多、易操作、可靠耐用，使机械加工的必备产品。
Foxboro 43AP Pneumatic Indicating Controllers 产品说明
FIELD DEVICES – CONTROLLERSProduct Specifications43AP Pneumatic Indicating ControllersThese instruments indicate and control pressure, temperature, vacuum, and differential pressure. They provide process industries with a highly dependable and versatile group of instruments.WIDE SELECTION OF MEASURING ELEMENTS Foxboro products offer the widest variety of element constructions and ranges in the industry. This versatility enables the 43AP Series Pneumatic Indicating Controllers to be applied to virtually any process.WIDE CHOICE OF CONTROL MODESOn-off, proportional, proportional plus derivative, proportional plus integral (reset), proportional plus integral plus derivative, differential gap, and automatic shutdown actions are available.BROAD RANGE OF INTEGRAL (RESET) AND DERIVATIVE ADJUSTMENTSThe integral unit has the complete range from0.01to 50 minutes, and the derivative unit from 0.05 to 50 minutes.VARIETY OF OPTIONSThese controllers are available with an extensive list of optional features. Among these are internal bumpless automatic-manual transfer stations (two types), “batch” function, remote pneumatic set point, Type 70 electric contacts, and control valvemounting.PSS 3-1B3 APSS 3-1B3 APage 2OPERATING CONDITIONSACCURACY UNAFFECTED BY MOUNTING STRESSESBoth the control unit and the measurement element are mounted on a rigid steel plate. Thus, these components are isolated from case stresses due to mounting, and dependable accuracy is ensured. POWER FAILURES DO NOT INFLUENCE PROCESS-DRIVEN INDICATIONA power failure and the likely subsequent loss of supply pressure do not influence the process-driven indication.WEATHERPROOF CONSTRUCTIONA glass fiber reinforced case and a gasketed door with a shatterproof polycarbonate window meet IEC IP53 and provide the environmental protection of NEMA®T ype 3.VERSATILE MOUNTINGInstruments may be mounted in a panel, on a flat surface, on a continuous vertical pipe, or on a vertical pipe stub.INTERNAL BUMPLESS AUTOMATIC-MANUAL TRANSFER STATIONThis option provides bumpless-balanceable transfer between automatic and manual control by simple 2-step procedure. Accidental transfer is avoided because the door must be opened to gain access to the transfer station.PERFORMANCE SPECIFICATIONS(Under Reference Operating Conditions unless otherwise specified)AccuracyINPUT TO POINTER±0.5% of span for qualified elements.INPUT TO OUTPUTDepends on measuring element used. Repeatability0.2% of span.Deadband0.1% of span.Ambient Temperature EffectMaximum control point shift at midspan per 55°C (100°F) change within normal operating conditions is 1% of input span.Supply Pressure EffectMaximum control point shift at midspan per 7 kPa (1psi) change within normal operating conditions is 0.2% of input span.OPERATING CONDITIONSAmbient T emperature24 ±2°C(75 ±3°F)–30 and +80°C(–20 and +180°F)–40 and +80°C(–40 and +180°F)Relative Humidity50% ± 10%No Limit No LimitSupply Pressure140 ± 1.4 kPa(20 ± 0.2 psi)115 and 155 kPa(17 and 23 psi)210 kPa(30 psi)FUNCTIONAL SPECIFICATIONSPSS 3-1B3 APage 3 FUNCTIONAL SPECIFICATIONSElementsRefer to “Measuring Element Specifications” on page4 for types, materials, and ranges. Controller ActionOutput signal either increases or decreases with increasing measurement, as specified; action is reversible in the field.Output Signal20 to 100 kPa, 3 to 15 psi, or 0.2 to 1.0 bar or kg/cm2, as specified.Air Consumption (Under normal operation)0.5 m3/h (0.3 cfm) at standard conditions.Output Gauge0 to 200 kPa, 0 to 30 psi, or 0 to 2 bar or kg/cm2, as specified.Set Point AdjustmentBy means of a knob mounted inside the case. PointersSet point and measurement pointers are fluorescent red.ScaleBlack markings on white background; sector-shaped with nominal effective length of 150 mm (6 in). (Refer to Chart and Dial Catalog 600 for available ranges.)Connections (Located in Bottom of Case.) PRESSURE AND VACUUMFor upper range-values up to 14 MPa(2000psi, or 140 bar or kg/cm2):Connections tapped for R1/4 or 1/4 NPT, asspecified.For upper range-values from 14 MPa(2000psi, or 140 bar or kg/cm[sup/2]) up to70 MPa (10000psi, or 700 bar or kg/cm2):Connections threaded for R1/2 or 1/2 NPT,as specified.For upper range-values above 70 MPa (10000psi, or 700 bar or kg/cm2):9/16-18 Aminco® fitting used.PNEUMATICSupply and output connections tapped for1/4NPT.MountingPANELFlush in a panel up to 16 mm (0.6 in) thick.SURFACESuitable for all controllers having internally-mounted elements. Note that this mounting isnot available with heavy duty helical elements.(These elements extend through the back of the case.)PIPEA kit of parts to fit a DN 50 or 2 in vertical pipe.YOKEKit of parts to fit a vertical DN 50 or 2 in pipestub. This mounting scheme is designedspecifically for controllers having rear-mounted differential pressure elements.PSS 3-1B3 A Page 4PHYSICAL SPECIFICATIONSPHYSICAL SPECIFICATIONSEnclosureThe case is a glass fiber reinforced polyester molding, compounded for superior corrosion resistance. The door is glass fiber reinforced phenylene oxide, and has a shatterproofpolycarbonate window, ultraviolet resistant. The overall construction is weatherproof, meets IEC IP53, and provides the environmental protection of NEMA Type 3.FinishCase, gray polyester; door, blue textured polyurethane.Data LabelAluminum data label fastened to inside of door with pressure sensitive adhesive. Includes space for Customer Tag data up to a maximum of 72characters and spaces. For additional space, see optional Customer T ag.Approximate Mass4.8 kg (10.6 lb), excluding element.MEASURING ELEMENT SPECIFICATIONS (To achieve stated Performance Specifications)Differential Pressure Elements (Refer to PSS 3-4A2 A)a.Body and cover material for DE-A is zinc-cobalt; material for DE-B is 316 ss.b.These are zero-based elements. The lower range value is zero and the upper range value is as shown (100% of span). Zerodifferential pressure can be elevated (compound range) so that lower range value is as low as -50% of span; or suppressed so that upper range value is as high as either –150% of span or 50 kPa (200 inH 2O) ∆P , whichever is less.22DE–A,BType 375 and 5020 and 20050 and 500142000140Temperature Elements—Filled Thermal Systems (Refer to PSS 3-3A1 A)T A–1A IA –130 and +315–200 and +60025 and 33040 and 600TA–2A and 2BIIA and IIB–45 and +315–50 and +600Varies with operating temperature (a)T A–3BIIIB–195 and +760–320 and +140070 and 550120 and 1000a.Does not include temperature overrange values. Narrow spans are at low end of range. The maximum span is 215︒C (400︒F)MEASURING ELEMENT SPECIFICATIONS PSS 3-1B3 APage 5Pressure Elements (Refer to PSS 3-2A1 A)P A–CA (d)Absolute Bellows316 ss170 and 240 kPa abs 2.5 and 35 psia P A–MA Absolute Double Spiral316 ss140 and 700 kPa abs20 and 100 psiaPB–AA PB–AM (e)Helical316 ssK-Monel1.4 and 40 MPa1.7 and 14 MPa200 and 6000 psi200 and 2000 psiPB–BA PB–BM (e)Spiral316 ssK-Monel82 and 1400 kPa140 and 1400 kPa12 and 200 psi20 and 200 psiPB–CA Bellows316 ss35 and 200 kPa 4.5 and 29 psiPB–CC Bellows Brass34 and 100 kPa vac30 and 180 kPa 4.9 and 15 psi 4 and 26 psiPB–DF Diaphragm 50 mm (2 in)Cu-Ni-Sn Alloy 6 and 35 kPa vac6 and 70 kPa 0.9 and 5 psi 0.9 and 10 psiPB–PF Diaphragm 75 m (3 in)Cu-Ni-Sn Alloy 2 and 6 kPa vac2 and 10 kPa 0.3 and 0.9 psi 0.3 and 1.5 psiPB–GA (f)Heavy-Duty Helical316 ss0.5 and 200 MPa75 and 30 000 psiPC 3 to 15 PC 3 to 27Receiver (Bellows)Brass20 to 100 kPa Range—3 to 15 psi Range3 to 27 psi Rangea.All elements except Code PC have zero-based ranges. Therefore, the lower range values are zero and the upper range valuesare as listed.b.To convert kPa to bar or kg/cm2, divide kPa value by 100. To convert MPa to bar or kg/cm2, multiply MPa value by 10.c.To convert psi to inH2O, multiply psi value by 27.73. To convert psi to inHg, multiply psi value by 2.036.d.Replacement element not calibrated.e.K-Monel elements comply with NACE Standard MR-01-75.f.Element extends through back of case. Replacement element not recommended. Return instrument to Global CustomerSupport.PSS 3-1B3 A Page 6MODEL CODEMODEL CODEDescription Model Indicating Controller43AP MountingField (Pipe or Y oke, as specified in complete element code)– F Panel or Surface– P Control On-OffA1Proportional 4 to 400%A2Proportional plus Derivative 0.05 to 50 minutesA3Proportional plus Integral (Reset) 0.01 to 50 minutes per repeat A4Proportional plus Integral plus Derivative A5Differential Gap 1 to 100%A7Automatic ShutdownA8Output Signal and Gauge20 to 100 kPa signal; 200 kPa gauge 53 to 15 psi signal; 30 psi gauge 20.2 to 1.0 bar signal; 2 bar gauge60.2 to 1.0 kg/cm 2 signal; 2 kg/cm 2 gauge4Automatic Manual Internal Transfer Switching NoneN Bumpless with 2-position switch, balance gauge, regulator C 2-position nozzle seal switch for manual controlD Optional SuffixRemote Pneumatic Set Point (Not available with pressure elementCodes P A–CA, P A–CC, PB–GA, T ype 70 Contacts, or AS Reference “BA TCH-H”.)– PElements Available (Refer to element specifications tables) (a)a.The 43AP also uses the /E Electronic Servo Element. Refer to PSS 3-1B3 B.Differential pressure, T ype 37 Diaphragm (43AP–F only)/DE–A, –B Absolute pressure, bellows/P A–CA Absolute pressure, double spiral /P A–MA Pressure, helical /–PB–AA, –AM Pressure, spiral /–PB–BA, –BM Pressure, bellows /–PB–CA, –CC Pressure, diaphragm/–PB–DF , –PF Pressure, heavy-duty helical (43AP–F only)/–PB–GA Pressure receiver, bellows/–PCT emperature, Filled Thermal System/–T A–1A, –2A,–2B, –3BExamples: 43AP–P A12N–P/PB–AA; 43AP–FA25C/DE–EOPTIONAL FEATURESPSS 3-1B3 APage 7 OPTIONAL FEATURESBumplessAutomatic-Manual T ransferStation Consists of precision balance tube, regulator, and 2-position switch locatedwithin enclosure. A simple 2-step procedure provides bumpless transferbetween automatic and manual control. A shutoff valve is supplied to allowautomatic controller and relay to be serviced while retaining manual control.See ModelCodeNozzle Seal Switchfor Manual Control An internally mounted 2-position switch provides a simple and inexpensivemethod of achieving manual control. In the manual position, the switch sealsthe nozzle circuit and the output can be changed by varying the controllersupply pressure with an external regulator.See ModelCodeRemote Pneumatic Set Point Integral AirSupply Set Enables the set point to be positioned from a remote source using a standardpneumatic signal. Available over the full span or part of the span.Fixed or adjustable combination pressure regulator and filter with 50mm (2 in)gauge mounted and piped to controllers. Fixed pressure regulator availablewithout gauge. Maximum input 1 MPa, 150 psi, or 10 bar or kg/cm2. NOTE:Not available with panel mounted controllers.See ModelCodeIASType 70 Electric Alarm Contacts This option comprises a rotor unit with up to 5 contacts. Relays are located in aseparate external sheet metal housing. One relay may be supplied to energizeon increasing or decreasing measurement, as specified. Or two relays may be provided, one energizing on increasing measurement and one on decreasing measurement. Relay contacts rating (noninductive load): 5 A at 120 V ac, 2 Aat 240 V ac, and 5 A at 24V ac or dc. Electrical classification: ordinarylocations.C–T/70Control Valve Mounting A 43AP Controller without elements extending from back of case may beassembled on a control valve fitted with a P50 or P110 Actuator at the factory.CVMExternal Connection to IntegralBellows Used when an external feedback signal must be applied to prevent integralcircuit saturation.ECRBExternal Set Point A knob is fitted on door and engages set point adjustment mechanism.ESPHigh “Batch”Modification For processes involving discontinuous control, the integral (reset) function ismodified to prevent overshoot and to initiate immediate corrective action whencontrol is resumed.BA TCH-HGas Tight Case Special case machining and a gasketed 1/2 NPT vent connection permitsoperation of the controller with clean, noncorrosive process gas.GTCExternal Phenolic Nameplate Laminated plastic nameplate 38 X 76 mm (1.5 X 3 in) with white characters ona black background. Maximum of 5 lines with 28characters or spaces 3 mm(0.13 in) high, or 24 characters or spaces 4 mm (0.16 in) high per line.N/PGlass Window inDoor Shatterproof glass window used in areas where abrasive dust can causescratching of standard polycarbonate window under frequent wiping conditions.GIDStainless Steel DataPlate A stainless steel data plate 36 X 40 mm (1.4 X 1.6 in). Maximum of 4lines with11 characters or spaces per line.SCTCustomer T ag Stainless steel tag attached to instrument for customer tag data that doesn't fiton data plate. There can be a maximum of 10 lines of data with 40 charactersper line.MTSPSS 3-1B3 APage 8OPTIONAL FEATURES Tamper-Proof Knob The door knob is removed to prevent unauthorized access to controladjustments. The door is opened with a specially shaped knob.TPKExternal Subpanel forAutomatic-Manual Switching For use only with controllers not having internal transfer switching. Consists ofpressure regulator, nominal 40 mm (1.5 in) gauge, and 2-position transferswitch completely piped and assembled to external subpanel mounted tobottom surface of enclosure. Subpanel is finished in gray. The 1 in AS Code isfor Control Codes A1, A2, A3, A7, and A8. The 2 in AS Code is for ControlCodes A4 and A5. The S in AS Code is gauge in kPa, the E is psi, and the M iskg/cm2.SD–1SSD–1ESD–1MSD–2DSD–2ESD–2Ma.AS is Auxiliary Specification.OPTIONAL FEATURES (CONTINUED)DIMENSIONS - NOMINALPSS 3-1B3 APage 9 DIMENSIONS - NOMINALPSS 3-1B3 APage 10NOTESNOTESPSS 3-1B3 APage 11NOTESInvensys Systems, Inc.10900 Equity DriveHouston, TX 77041United States of America Global Customer Support Inside U.S.:1-866-746-6477Outside U.S.:1-508-549-2424Website: Copyright 1977-2015 Invensys Systems, Inc. All rights reserved.Invensys and Foxboro are trademarks of Invensys Limited, its subsidiaries, and affiliates. All othertrademarks are the property of their respectiveowners.Invensys is now part of Schneider Electric.0715PSS 3-1B3 APage 12ORDERING INSTRUCTIONSOTHER FOXBORO PRODUCTS1. Model Number2. Mounting3. Element T ype, Material, and Range4. Measurement Range5. Measurement Connection6. Scale Range7. Supply Pressure and Output Signal8. Controller Action9. Optional Features 10. T ag and ApplicationThe Foxboro product lines offer a broad range of measurement and instrument products, including solutions for pressure, flow, analytical, temperature, positioning, controlling, and recording.For a list of these offerings, visit our web site at:。
美达尔044948产品说明说明书
Eaton 044948Eaton Moeller® series B3 Three-phase busbar link, Circuit-breaker:5, 261 mm, For PKZM0-... or PKE12, PKE32 without side mountedauxiliary contacts or voltage releasesGeneral specificationsEaton Moeller® series B3 AccessoryThree-phase busbar link0449484015080449485264 mm34 mm11 mm0.109 kgCECSA Class No.: 3211-06CSA File No.: 98494ULUL File No.: E36332CSACSA-C22.2 No. 14IEC/EN 60947-4-1UL 508UL Category Control No.: NLRV B3.1/5-PKZ0Product Name Catalog NumberEANProduct Length/Depth Product Height Product Width Product Weight Certifications Model CodeBlackForkInsulatedCan be extended by rotating installation 3Three-pole 45 + 9 mmIII3Accessories 6000 V AC5 Circuit-breakers-25 °C 55 °C 690 V 690 V 63 A0 kA 0 kA 8.4 W0 W2.8 W63 A0 WMeets the product standard's requirements.ColorElectric connection type FeaturesFunctionsNumber of phases Number of poles Mounting widthOvervoltage categoryPollution degreeProduct categoryRated impulse withstand voltage (Uimp) Suitable forAmbient operating temperature - min Ambient operating temperature - max Rated operational voltage (Ue) - max Rated operational voltage (Ue) at AC - max Rated uninterrupted current (Iu)Rated conditional short-circuit current (Iq) Rated short-time withstand current (Icw)Equipment heat dissipation, current-dependent PvidHeat dissipation capacity PdissHeat dissipation per pole, current-dependent PvidRated operational current for specified heat dissipation (In) Static heat dissipation, non-current-dependent Pvs10.2.2 Corrosion resistanceMeets the product standard's requirements.Meets the product standard's requirements.Meets the product standard's requirements.Meets the product standard's requirements.Does not apply, since the entire switchgear needs to be evaluated.Does not apply, since the entire switchgear needs to be evaluated.Meets the product standard's requirements.Does not apply, since the entire switchgear needs to be evaluated.Meets the product standard's requirements.Does not apply, since the entire switchgear needs to be evaluated.Does not apply, since the entire switchgear needs to be evaluated.Is the panel builder's responsibility.Is the panel builder's responsibility.Is the panel builder's responsibility.Is the panel builder's responsibility.Is the panel builder's responsibility.Save time and space thanks to the new link module PKZM0-XDM32ME Motor Starters in System xStart - brochureProduct Range Catalog Switching and protecting motorsSwitching and protecting motors - catalogDA-DC-00004245.pdfDA-DC-00004109.pdfDA-DC-00004544.pdfDA-DC-00004601.pdfDA-DC-00004951.pdfDA-DC-00004890.pdfDA-DC-00004944.pdfDA-DC-00004879.pdfDA-DC-00004888.pdfDA-DC-00004884.pdfDA-DC-00004917.pdfDA-DC-00004945.pdfDA-DC-00004891.pdfDA-DC-00004920.pdfDA-DC-00004911.pdfDA-DC-00004892.pdfDA-DC-00004962.pdfDA-DC-00004918.pdfDA-DC-00004887.pdfDA-DC-00004883.pdfDA-DC-00004914.pdfDA-DC-00004921.pdfeaton-manual-motor-starters-busbar-b3-accessory-dimensions-007.eps eaton-manual-motor-starters-busbar-b3-accessory-3d-drawing-007.epsDA-CE-ETN.B3.1_5-PKZ010.2.3.1 Verification of thermal stability of enclosures10.2.3.2 Verification of resistance of insulating materials to normal heat10.2.3.3 Resist. of insul. mat. to abnormal heat/fire by internal elect. effects10.2.4 Resistance to ultra-violet (UV) radiation10.2.5 Lifting10.2.6 Mechanical impact10.2.7 Inscriptions10.3 Degree of protection of assemblies10.4 Clearances and creepage distances10.5 Protection against electric shock10.6 Incorporation of switching devices and components10.7 Internal electrical circuits and connections10.8 Connections for external conductors10.9.2 Power-frequency electric strength10.9.3 Impulse withstand voltage10.9.4 Testing of enclosures made of insulating material BrochuresCataloguesCertification reports Declarations of conformityDrawingseCAD modelInstallation instructionsEaton Corporation plc Eaton House30 Pembroke Road Dublin 4, Ireland © 2023 Eaton. All rights reserved. Eaton is a registered trademark.All other trademarks areproperty of their respectiveowners./socialmediaThe panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.Is the panel builder's responsibility. The specifications for the switchgear must be observed.Is the panel builder's responsibility. The specifications for the switchgear must be observed.The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.IL122027ZUWIN-WIN with push-in technologyDA-CS-b3_1_5_pkz0DA-CD-b3_1_5_pkz010.10 Temperature rise10.11 Short-circuit rating10.12 Electromagnetic compatibility 10.13 Mechanical function Installation videos mCAD model。
主机注油器原理
目录前言-------------------------------------------------------------------------2 1 Alpha注油器系统组成及工作原理--------------------------------------------31.1 Alpha注油器系统组成--------------------------------------------------31.2 Alpha注油器系统工作原理----------------------------------------------51.3 注油器的工作模式-----------------------------------------------------61.3.1 主控单元（MCU）模式工作----------------------------------------61.3.2 备控单元（BCU）模式工作----------------------------------------71.3.3 应急模式工作---------------------------------------------------72 Alpha注油器系统注油率----------------------------------------------------82.1 Alpha电子注油器设计应用时的一些相关计算------------------------------82.1.1 Alpha电子注油器的主要尺寸参数的确定----------------------------92.1.2 计算各状态、各工况率下的注油频率-------------------------------92.2 注油率计算方法------------------------------------------------------102.3 Alpha注油器实际注油率控制-------------------------------------------112.3.1 按最大持续功率计算--------------------------------------------112.3.2 按燃油含硫量计算----------------------------------------------112.3.3 注油率控制调节中注意问题--------------------------------------123 系统维修保养管理要点------------------------------------------------------133.1 日常使用中-----------------------------------------------------------133.2 每月-----------------------------------------------------------------133.3 每季度---------------------------------------------------------------133.4 每半年---------------------------------------------------------------134 总结----------------------------------------------------------------------13摘要：“育鲲”轮主机为MAN B&W 6S35MC型柴油机，本文从系统组成、工作原理、注油率计算调节等方面介绍了该轮主机的Alpha电子汽缸油注油器系统，并提出注油率调节过程中应注意的问题以及系统维修保养管理要点。
巨鹰Giant204 四通道称重模块 用户手册说明书
Giant204四通道称重模块用户手册 V1.0目录1 技术支持 (3)2 产品介绍 (4)3 技术参数 (5)4 外形尺寸,电气连接以及选型 (6)4.1 外形尺寸 (6)4.2 电气连接与说明 (6)4.2.1 称重传感器连接 (7)4.2.2 指示灯 (8)4.2.3 通信接口RS232/RS485 (8)4.3 选型 (8)5 显示与按键 (9)6 功能与设置 (10)6.1 主界面显示与功能 (11)6.1.1 相关指令 (12)6.2功能菜单 (15)6.2.1 相关指令 (16)6.3校准菜单 (21)6.3.1 校准方式选择菜单 (21)6.3.2 实物校准菜单 (22)6.3.3 数字校准菜单 (24)6.3.4 相关指令 (25)6.4 参数保存菜单 (27)6.4.1相关指令 (27)6.5 显示设置菜单 (28)6.5.1相关指令 (28)6.6 通信设置菜单 (29)6.6.1 相关指令 (30)7 MODBUS通讯协议 (33)8用户设置软件 (40)8.1 软件安装与启动 (40)9 附件 (41)9.1 仪表显示的错误代码 (41)9.2 基本术语 (41)9.3 标准ASCII码 (42)1 技术支持感谢您选择并使用大连哲勤科技有限公司产品，此用户手册协助您了解并正确使用设备。
如需订购产品、技术支持、以及产品信息反馈，请通过以下方式联系我们。
请在联系时附注设备的购买时间，购买方式，联系人信息，地址以及电话等相关信息，便于我们为您服务。
网址E-Mail**************电话+86-411-66831953， 4000-511-521传真+86-411-82388125版本控制2 产品介绍Giant204四通道称重变送器是面向工业控制领域的重量变送器，集四个高速称重通道，RS485和RS232通信接口于一体（Modbus-RTU通信协议），同时进行四个重量的独立并行高速检测。
KOD -Plus- Neo 1109 F1066K说明书
manual KOD -Plus- Neo 1109 F1066K KOD -Plus- NeoKOD-401 200 U 200 reactionsStore at -20°C Contents[1] Introduction[2] Components[3] Quality testing[4] Primer design[5] Cloning of PCR products[6] Protocol1. Standard reaction setup2. Cycling conditions[7] Examples[8] Troubleshooting[9] References[10] Related productsC AUTIONAll reagents in this kit are intended for research purposes. Do not use for diagnostic or clinical purposes. Please observe general laboratory practices and safety precautions while using this kit.JAPAN CHINATOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140www.toyobo.co.jp/e/bio 1JAPAN CHINA TOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140 www.toyobo.co.jp/e/bio********************1[ 1 ] IntroductionDescriptionKOD -Plus- Neo is based on a DNA polymerase from the hyperthermophilic Archaeon Thermococcus kodakaraensis KOD11) 2). This polymerase exhibits excellent PCR fidelity because of its efficient 3’J 5’ exonuclease activity (proof reading activity). This product contains a unique “elongation enhancer” that suppresses the “plateau effect” produced by conventional PCR. Therefore, this reagent exhibits greater amplification efficiency and elongation capability compared to the previous version of KOD -Plus- (Code No. KOD-201).Moreover, this enzyme requires only 30 sec/kb for the PCR extension step. This facilitates the long range PCR.This enzyme contains two anti-KOD DNA polymerase antibodies that inhibit polymerase and 3’J 5’ exonuclease activity, thus allowing for Hot Start PCR 3). This polymerase generates blunt-end PCR products due to 3’J 5’ exonuclease (proof-reading) activity.Features-KOD -Plus- Neo exhibits 80-fold greater PCR fidelity than Taq DNA polymerase.-“Elongation enhancer” enables greater amplification efficiency and elongation capability(up to 24 kb from human genomic DNA) compared to conventional PCR.-Requires only 30 sec/kb for the PCR extension step.-2-step cycle conditions can be used for amplification using ≥ 20 mer primers (melting temperatures, Tm >63°C).JAPAN CHINATOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140www.toyobo.co.jp/e/bio********************2[ 2 ] Components[ 3 ] Quality Testing [ 4 ] Primer Design[ 5 ] Cloning ofPCR products*The Nearest Neighbor method is recommended to calculate the Tm of primers. The Tm values in this manual were calculated using this method with the following parameters.Na+ concentration: 50 mMOligonucleotide concentration: 0.5 μMKOD -Plus- Neo (1.0 U/μl)* 200μl x 110 x PCR Buffer for KOD -Plus- Neo 1 ml x 125 mM MgSO4 1 ml x 12 mM dNTPs 1 ml x 1*The enzyme solution contains anti-KOD DNA polymerase antibodies that neutralize polymerase and 3’J5’ exonuclease activity.Quality control was performed by amplifying the human β-globin gene (17.5 kb).-Primers should be 22–35 bases with Tm >63°C.-Optimal GC content of primers is 45–60%. Ideal GC contents of the 5’ half and the 3’half are 60–70% and 40–50%, respectively.-Primers for long target amplification should be 25-35 bases with Tm >65°C.-Primers containing inosine cannot be used.-The Tm of primers should be calculated using the Nearest Neighbor method. The Tm values in this manual were calculated using this method with the following parameters. Na+ concentration: 50 mMOligonucleotide concentration: 0.5 μM-KOD -Plus- Neo generates blunt-end PCR products due to its 3’J5’ exonuclease (proof-reading) activity. Therefore, PCR products can be cloned according to blunt-end cloning methods.-PCR products of KOD -Plus- Neo should be purified prior to restriction enzyme treatments. The 3’J5’ exonuclease activity of KOD DNA polymerase remains at the end of the PCR reaction.-The dedicated TA cloning kit “TArget clone™ -Plus- (Code No. TAK-201)” is recommended for the cloning of blunt end PCR products produced by KOD DNA polymerase (see [10] Related product).JAPAN CHINA TOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140 www.toyobo.co.jp/e/bio********************3[ 6 ] Protocol1. Standard reaction setupThe following procedure is designed for use with the components provided in this kit. Before mixture preparation, all components should be completely thawed, except for the enzyme solution.*Do not use dNTPs from other kits or companies. Notes:-Optimal primer concentration is 0.3 μM. In the case of long target (≥10 kb), a reduced primer concentration (0.15 μM) may give more effective amplification.-The addition of DMSO (final conc. 2–5%) is beneficial for the amplification of GC-rich targets. Decreased PCR fidelity does not occur in the presence of DMSO (See step 2, Cycling conditions).-Contaminating RNA in cDNA or genomic DNA inhibits the PCR reaction by chelating Mg 2+. PCR should be performed using template DNA containing <200 ng RNA.-Quality of template DNA should be checked by electrophoresis. The length and purity of template DNA affects amplification results.-Templates containing uracil cannot be used for amplification.-For PCR reactions, thin-wall tubes are recommended. A total reaction volume of 50 μl is also recommended.Component Volume Final Concentration 10x Buffer for KOD -Plus- Neo 5 μl 1x 2 mM dNTPs* 5 μl 0.2 mM each 25 mM MgSO 4 3 μl 1.5 mM 10 pmol/μl Primer #1 0.75–1.5 μl 0.15–0.3 μM 10 pmol/μl Primer #2 0.75–1.5 μl 0.15–0.3 μMTemplate DNA X μl Genomic DNA ≤ 200 ng/50 μlPlasmid DNA ≤ 50 ng/50 μlcDNA ≤ 200 ng （RNA equiv.)/50 μlPCR grade water Y μl KOD -Plus- Neo (1.0 U/μl) 1 μl 1.0 U/50 μl Total reaction volume 50 μlJAPAN CHINA TOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140 www.toyobo.co.jp/e/bio********************42. Cycling conditions [Important]Two-step cycle conditions with primers ≥20 mer, Tm >63°C are recommended for effective amplification using KOD -Plus- Neo.A. 2-step cycleIf the Tm value of the primer is over 63°C, a 2-step cycle is recommended.Notes :-For amplification using low copy templates or amplification of long targets (>10 kb), longer extension times (up to 1min/kb) or higher Mg concentrations (up to 2 mM final concentration) may increase the yield.-The addition of DMSO (final conc. 2–5%) may be beneficial for the amplification of GC-rich targets. The concentration of DMSO used should be determined according to the Tm of the primers.<25 mer or Tm <68°C: up to 2% ≥25 mer or Tm ≥68°C: up to 5%-In the case of amplification failure a 3-step cycle may be required.< 2-step cycle > Pre-denaturation: 94°C, 2 min Denaturation:98°C, 10 secExtension: 68°C, 30 sec/kb 25-45 cyclesJAPAN CHINA TOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140 www.toyobo.co.jp/e/bio********************5B. 3-step cycleWhen the Tm of primers are less than 63°C, a 3-step cycle should be used.Notes:-Amplification using low copy templates or amplification of long targets (>10 kb) may be improved by increasing the extension time (up to 1 min/kb) or Mg concentration (up to 2 mM final concentration).-The addition of DMSO (final conc. 2–5%) might be beneficial for the amplificationof GC-rich targets. C.Step-down cycleIf non-specific amplification is observed with 2-step and 3-step cycle conditions (extra or smeared bands observed after electrophoresis of PCR product), then the step-down cycle may improve specificity.Notes:-Amplification from low copy templates or amplification of long targets (>10 kb), may be improved by increasing the extension time (up to 1 min/kb) or the Mg concentration (up to 2 mM final concentration).< 3-step cycle > Pre-denaturation: 94°C, 2 min Denaturation:98°C, 10 secAnnealing: [Tm]oC, 30 sec Extension: 68°C, 30sec/kb < Step-down cycle > Pre-denaturation: 94°C, 2 min Denaturation: 98°C, 10 sec Extension: 74°C , 30 sec/kb Denaturation: 98°C, 10 sec Extension: 72°C , 30 sec/kb Denaturation: 98°C, 10 sec Extension: 70°C , 30 sec/kb Denaturation: 98°C, 10 sec Extension: 68°C , 30 sec/kbExtension: 68°C , 7 minJAPAN CHINATOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140www.toyobo.co.jp/e/bio********************6[ 7 ] Examples-The addition of DMSO (final conc. 2–5%) might be effective for the amplification of GC-rich targets. The DMSO concentration should be determined according to the Tm of primers.<25 mer or Tm <68°C: up to 2%≥25 mer or Tm ≥68°C: up to 5%Performance data 1． PCR fidelityMutation frequency was measured by sequence analysis of human β-globin gene products amplified from human genomic DNA via TA cloning with TArget Clone™ -Plus-. KOD -Plus- Neo showed excellent fidelity and the mutation frequency was equal to that of the previous version of the enzyme (KOD -Plus-).Performance data 2． Elongation capabilityTargets of various sizes were amplified from human genomic DNA by several PCR enzymes according to the recommended conditions of each enzyme. KOD -Plus- Neo successfully amplified targets up to 17.5 kb.JAPAN CHINA TOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140 www.toyobo.co.jp/e/bio********************7Performance data 3． Amplification from low copy templatesFour genes were amplified using 0.5 ng cDNA template (RNA equiv.). Templates were synthesized from total RNA of HeLa cells. KOD -Plus- Neo successfully amplified all genes.Performance data 4． Elongation rateThe β-globin gene (3.6 kb) was amplified from human genomic DNA (50 ng) using various extension times. KOD -Plus- Neo can amplify a 3.6 kb target using an extension time of 30 sec/kb.JAPAN CHINA TOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140 www.toyobo.co.jp/e/bio********************8Application data 1． Amplification of various protein kinase targetsVarious protein kinase open reading frames (ORFs) were amplified using cDNA synthesized from total RNA of HeLa cells. KOD -Plus- Neo successfully amplified alltargets.Application data 2． Amplification of long targetsLong targets were amplified from human genomic DNA using various concentrations of primers. Excessive amounts of primer inhibit the amplification. Therefore, long targets (>10 kb) should be amplified using lower primer concentrations of approximately 0.15 μM.JAPAN CHINA TOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140 www.toyobo.co.jp/e/bio********************9[ 8 ] Troubleshooting[ 9 ] Reference1) Takagi M, Nishioka M, Kakihara H, Kitabayashi M, Inoue H, Kawakami B, Oka M, and Imanaka T., Appl Environ Microbiol., 63: 4504-10 (1997)2) Hashimoto H, Nishioka M, Fujiwara S, Takagi M, Imanaka T, Inoue T and Kai Y , J Mol Biol ., 306: 469-77 (2001)3) Mizuguchi H, Nakatsuji M, Fujiwara S, Takagi M and Imanaka T, J Biochem ., 126: 762-8 (1999)4) Fujii S, Akiyama M, Aoki K, Sugaya Y , Higuchi K, Hiraoka M, Miki Y , Saitoh N, Yoshiyama K, Ihara K, Seki M, Ohtsubo E and Maki H, J. Mol. Bio l., 289: 835-850 (1999)SymptomCauseSolutionNo PCR product/low yield Cycling conditions are not suitable.Using the 3-step cycle, lower annealing temperature incrementally to a maximum of Tm-5–10°C.Prolong the extension time to 1 min/kb.Increase the number of cycles by 2–5 cycles. Mg concentration is low.Increase the Mg concentration up to 2 mM. High GC content of target sequence.Add DMSO 2–5%.[See Cycling conditions]Quality and/or quantity of primers is not sufficient.Decrease the primer concentration incrementally down to 0.15 μM. Use fresh primers. Redesign primers.Quality and/or quantity of template DNA is not sufficient.Check the quality of template DNA. RNA inhibits amplification.Increase the amount of template DNA.Enzyme concentration is low.Increase enzyme concentration up to 1.5–2.0 U/50 μl.Smearing/extra bandCycling conditions are not suitable.Decrease the number of cycles by 2–5 cycles. Change from 3-step cycle to 2-step cycle. Change from 2-step cycle to Step-down cycle. Quality of primers is not sufficient.Use fresh primers. Redesign primers.Too much template DNA. Reduce the amount of template DNA.Too much Mg. Reduce MgSO 4 incrementally down to 1.0 mM. Too much enzyme. Reduce enzyme concentration to 0.5–0.8 U/50 μl. Poor TA cloning efficiency. PCR products have blunt-ends.Clone the PCR products according to general blunt-end cloning guidelines.Use TArget clone™ -Plus- (Code No.TAK-201) [See Related products].JAPAN CHINA TOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140 www.toyobo.co.jp/e/bio********************10[ 10 ] Related productsProduct namePackage Code No. TArget Clone™ -Plus- 10 reactions TAK-201 10x A-attachment mix 25 reactions TAK-301 Ligation high Ver.2 750 μl(100 reactions)LGK-201TArget Clone™ -Plus- is a high efficient TA cloning kit. The kit can be applied to the TA cloning of blunt-end PCR products amplified using KOD -Plus- [Code No. KOD-201], KOD -Plus- Neo [Code No. KOD-401] or KOD FX [Code No. KFX-101]. The kit contains pTA2 Vector, 2x Ligation Buffer, T4 DNA Ligase and 10x A-attachment Mix.10 x A-attachment mix is a reagent comprising anti-KOD DNA polymerase antibody specific to KOD 3’J 5’ exonuclease activity (proof-reading activity), as well as Taq DNA polymerase, which exhibits terminal transferase activity. PCR products from KOD -Plus- [Code No. KOD-201] and KOD FX [Code No. KFX-101] possess blunt ends due to 3’J 5’ exonuclease activity of the KOD DNA polymerase. The 10 x A-attachment mix allows for PCR products to acquire overhanging dA at the 3’-ends. Products with 3’-dA overhangs can be directly cloned into arbitrary T-vectors using ligation reagents, such as Ligation high Ver.2 [Code No. LGK-201].Fig. Principle of the 10 x A-attachment mixAnti-KOD DNA polymeraseAJAPAN CHINA TOYOBO CO., LTD. TOYOBO Bio-Technology, CO., LTD.Tel(81)-6-6348-3888 Tel(86)-21-58794900.4140 www.toyobo.co.jp/e/bio********************NOTICE TO PURCHASER: LIMITED LICENSEUse of this product is covered by one or more of the following US patents and corresponding patent claims outside the US: 5,079,352, 5,789,224, 5,618,711, 6,127,155 and claims outside the US corresponding to US Patent No. 4,889,818. The purchase of this product includes a limited, non-transferable immunity from suit under the foregoing patent claims for using only this amount of product for the purchaser’s own internal research. No right under any other patent claim (such as the patented 5’ Nuclease Process claims in US Patents Nos. 5,210,015 and 5,487,972), no right to perform any patented method, and no right to perform commercial services of any kind, including without limitation reporting the results of purchaser's activities for a fee or other commercial consideration, is conveyed expressly, by implication, or by estoppel. This product is for research use only. Diagnostic uses under Roche patents require a separate license from Roche. Further information on purchasing licenses may be obtained by contacting the Director of Licensing, Applied Biosystems, 850 Lincoln Centre Drive, Foster City, California 94404, USA.。
真空滴油式注油器
真空滴油式注油器用途：单柱塞真空滴油式注油器适用于空气/天然气CNG往复式压缩机、往复泵、锻压机、发动机等带压工作的机械。
在其运转工作时，对摩擦零部件强行压注润滑油，以减轻机件磨损，保证机器正常运转。
组成：单柱塞真空滴油式注油器由安装在油箱上表面的若干个注油泵，油箱及传动部份组成。
1、注油泵注油泵是单柱塞真空滴油式注油器的主要部份，每支注油泵用螺钉固定在箱体上。
由凸轮轴的旋转推动杠杆绕支承销作摆动。
当凸轮的偏心距逐渐减小时，在弹簧的作用下柱塞向下移动，使泵体之柱塞套内形成真空。
由于大气压的作用将润滑油由吸油管吸入，吸入的润滑油经过泵体内进油管道进入滴油管中，此时视油罩内亦处于真空状态，藉此真空将油从滴油管中吸出，吸出的油又由视油罩内的小孔重新进入泵体，这样视油罩内形成为一密闭的通路。
当偏心距逐渐增大时，柱塞向上移动将润滑油经注油阀排出送至各润滑点，可根据用户润滑点的数目，在箱体上排布所需数目的注油泵。
根据柱塞直径和柱塞行程的不同制造有：中压（16Mpa)、高压（32Mpa)、超高压（40、63、100Mpa)三大类注油泵。
注油泵与其相应的油箱及传动部份可组成中压，高压，超高压三大类单柱塞真空滴油式注油器。
2、油箱油箱是贮存润滑油、安装注油泵、支承凸轮轴的部份，每台单柱塞真空滴油式注油器通常有一至二个油箱（单联为一个，双联为二个）。
注油泵排列固定于油箱体平面上。
每只注油泵的工作运动由箱中凸轮带动。
凸轮轴按产品规格不同（即润滑点不同）由不同数目的凸轮组成。
凸轮轴的转动由传动部份供给。
3、传动部份单柱塞真空滴油式注油器传动部份有两大类：I 由主机带动；II 单独传动。
I .由主机带动的单柱塞真空滴油式注油器，有三种标准型式：（1）ZL型：联轴器型，由主机通过超越离合联轴器传动工作；（2）ZB型：摆杆型，由主机带动摆杆传动工作；（3）ZJ型：键联接型，凸轮轴头部带有平键，由主机直接传动工作。
II.单独传动的单柱塞真空滴油式注油器有ZD型：由电动机通过下面减速器（蜗杆，蜗轮减速和小，大齿轮减速）的二级传动带动凸轮轴转动。
风机林肯润滑手册
安装 ·安全设备
－不能作改动或使其失效； －仅当安装泵时才能拆除； －泵安装好后需重新装回。 ·QUICKLUB 润滑泵必须远离热源。 ·必须采用林肯原来的部件（见部件目录）或许可
的部件。 ·应遵守： －在钻孔和焊接作业时应遵守车辆或设备制造商的
安装手册要求； －镗孔之间和镗孔与机架上下缘之间规定的最小距
·根据“排量调节图”（图 5）可取得所需排 量的尺寸“S”值
注：最大排量时的“S”值为 29±0.1mm.
LINCOLN GmbH & Co. KG ∗ Postfach 1263 ∗ D-69183 Walldorf ∗ Tel.: +49 (6227) 33-0 ∗ Fax.: +49 (6227) 33-259
需改动则应事先咨询制造商或其代表。
事故预防条例 ·遵守本国现行事故预防条例
操作、维护和维修 ·维修工作必须由经过培训的熟悉本说明的授权人
员来进行。 ·林肯 QUICKLUB 润滑泵必须配备了安全阀才能
投入运行。 ·林肯 QUICKLUB 润滑泵必须采用干净油/脂。
注意：若从顶盖处往油箱内补油，则 必须在补油前切断电源。
用户手册 操作指南
使用与维护手册
LINCOLN GmbH & Co. KG * Postfach 1263 * D-69183 Walldorf * Tel.: +49 (6227) 33-0 *Fax.: +49 (6227) 33-259
用户手册 操作指南
风机用林肯集中润滑系统
LINCOLN GmbH & Co. KG * Postfach 1263 * D-69183 Walldorf * Tel.: +49 (6227) 33-0 *Fax.: +49 (6227) 33-259
科视Christie Spyder X20 视频处理器指南说明书
CHRISTIE SPYDER X20Fast and flexible video processing and matrix switchingAuditoriums Boardrooms Broadcast studios Conference rooms Control rooms Houses of worship Media centers Post-production Rental and staging Training roomsThe Christie® Spyder X20 is a versatile hardware-based video processor combined with the flexibility of a universal routing switcher. Its integrated source monitoring enables simultaneous, real-time, full frame rate monitoring of all inputs.The Spyder X20 provides users with a 20 megapixel bandwidth to blend, window, mix and scale any source format and then routes the signal to any destination device or combination of display devices – quickly and easily. It is easy to deploy and install because of its advanced architecture and reduces the amount of wires, boxes and rack space traditionally required because everything is all in one unit.Unrestricted multi-window processingThe Christie® Spyder X20 offers a unique architecture that allows for a resolution and video-format-independent environment. Users are no longer restricted to the resolution of a single computer or video source, or a single display destination. Multiple displays can be combined to generate an enhanced resolution to exceed what any single display can support.Ideal for live event and broadcast environments, its20 megapixel bandwidth enables the Spyder X20 to drive multiple displays to achieve higher brightness, image quality and resolution. The Spyder X20 can be used in many different environments and with any combination of display devices.Key featuresAdditional features › 20 megapixel bandwidth › I nternal matrix switching›Universal input/output capabilities – mix and matchmultiple formats with one piece of equipment›Input capability – either 8 or 16 inputs (depending onmodel) that can be a mix of analog BNC and DVI signals›Output capability – 8 outputs that natively support anydisplay from component analog 480i to digital 4K›Built-in conversion for analog/digital, interlaced/progressive, resolution, aspect ratio and refresh rate›2D and 3D capabilities›Manages and displays multiple 3D sources›Define properties for each output independentof each signal›Integrated source monitoring – real-time and fullframe-rate view of all sources connected to the Spyder X20 (either 16 or 8 inputs) on a single output, tiled into either a 4x4 array (X20-1608) or a 4x2 array (X20-0808)›Single point of control for all processing and signaldistribution functions from front panel, PC via Ethernet, or external control system›10-bit processing›Small form factor – (LxWxH): 21.9 x 17.3 x 7.0" (556 x 439x 178mm). Additionally, only one piece of equipment is required so the overall space used in a rack is reduced›Each output individually supports rotation –enabling the creation of vertically-oriented displays›User-definable edge blending and tiling›Create any kind of window border or drop shadowwith adjustable color, width, softness, shadow offset and transparency›Online editing mode allows for preset displays to be builtand edited in preview mode without affecting what the audience is seeing›Built-in image Still Storefunctionality›Built-in VESA calculatorfor custom resolution outputs›Intuitive graphical userinterface (GUI)›Simple cohesive controlof all functions›Redundant hot swappablepower supplies›Optional stereoscopicsupport›Advanced auto-syncfunctionality›Bitmap borders ›Window titling›Optional HDCP supportThis generation of SpyderThe Spyder X20 is designed for users in any environment to take images from unique sources, use a variety of display systems and present the images as intended. It is ideal for applications such as live events, broadcast, high-end boardrooms, command and control, houses of worship and education – anyinstallation that has multi-windowing, multiple displays and processing requirements.The Spyder X20 also offers the flexibility to display 2D and 3Dcontent simultaneously in the same display.Remote PC functionality allows the support of multiple remote servers to match certain securityrequirements and classification levels Software interfaceThe Microsoft® Windows® based control software provides full set-up, configuration, and real-time controlwith an easy-to-use interface.V ista Advanced is a Windows-based software interface that makes it easy to configure and control the Spyder X20.R educed rack spaceB itmap bordersFor the most current specification information, please visit Copyright 2022 Christie Digital Systems USA, Inc. All rights reserved. All brand names and productnames are trademarks, registered trademarks or tradenames of their respective holders. Performance specifications are typical. Due to constant research, specifications are subject to change without notice. CHRI4546_SpyderX20_Brochure_DEC_21_EN。