国外民用船舶修理价格表
《国内民用船舶修理价格表》92黄本
《国内民用船舶修理价格表》使用说明1. 本《价格表》系参照我中国船舶工业总公司系统各船厂的历史资料并结合修船产品实际情况和现行市场价格水平，经测算整理汇编成册，供我公司系统各单位使用。
2.本《价格表》仅适用于民用常规船舶的修理。
3.本《价格表》中已包括材料的项目，其材料费是按91年现行价格测算的，如遇材料市场价格有较大变动时，各厂按实际情况适当调整其差价部分。
4.本《价格表》中各分项说明中均已明确修换范围，其他附带工程及可能产生的零部件换新以及施工工艺所需的专用工具、模具、胎架、专用设备等费用另计。
5.凡单一性技术劳动，如柴油机的喷油器、高压油泵、调速器、冰机、空调等的修理价格可作适当上浮。
6. 本《价格表》所列的各档规格，凡在两档之间者均按高一档价格计。
7. 本《价格表》中各部分的系数，凡遇多个同时出现时，应将系数相加后计算。
本《价格表》所列之价格，均系出厂价格。
9. 凡工厂委托外单位加工、借用设备、外购器材等，应按工厂实际支付费用加上运杂费、管理费及法定利润、税金。
10.本《价格表》之价格仅适用于厂区作业，离厂区作业及出差施工价格另计。
11.本《价格表》适用于正常工作日的日班作业，若船方要求特急需逾时加班者，则应增收加班费。
12.船舶在工厂修理期间，其因修换而拆下的旧件、旧料，均归船厂所有。
服务项目殊船型价格另计）消防值班：以一天24小时计，不足一天按一天计算，每天每人:消防巡回检查， 以一天24小时计，不足一天按一天计算。
五、七、临时放置消防器材：50元/只八、供淡水、供电：按当地实际情况计价。
二、码头费：以船长每米24小时一天计，不足一天按一天计算，每天每米:5元（注：特船舶靠离码头系解缆：元/次（注：下列价格不包括拖轮费 ）85元。
四、八、1、 2、 3、 电缆接拆一次：138元 水管接拆一次：102元 消防软管接拆一次：102元清除生活垃圾，船长100米以下40 元 /天船长100米以上 70 元 /天注：船舶进厂后局部测爆每次每处50元；厂区外测爆交通费另计。
《国内民用船舶修理价格表92黄本》
《国内民用船舶修理价格表》使用说明一、本《价格表》系参照我中国船舶工业总公司系统各船厂的历史资料并结合修船产品实际情况和现行市场价格水平,经测算整理汇编成册,供我总公司系统各单位使用。
二、本《价格表》仅适用于民用常规船舶的修理。
海洋钻井平台、工程船舶及其它特种船舶中的特殊设施修理价格另计.三、本《价格表》中已包括材料的项目，其材料费是按91年现行价格测算的,如遇材料市场价格有较大的变动时,各厂可按实际情况适当调整其差价部分。
四、本《价格表》各分项说明中均已明确修换范围，其附带工程及可能的零部件换新以及施工工艺所需的专用工具、模具、胎架、专用设备等费用另计。
五、凡单一性技术劳务,如柴油机的喷油器、高压油泵、调速器、冰机、空调等的修理价格可作适当上浮。
六、本《价格表》所列的各档规格，凡在两档之间者均按高一档价格计。
七、本《价格表》中各部分的系数，凡遇多个同时出现时，应将系数相加后计算。
八、本《价格表》所列价格，均系出厂价格.九、凡工厂委托外单位加工、借用设备、外购器材等，应按工厂实际费用加上运杂费、管理费及法定利润、税金。
十、本《价格表》之价格仅适用于厂区作业，离厂区作业及出差施工其价格另行计算.十一、本《价格表》适用于正常工作日的日班作业，若船方要求特急,需逾时加班者，则应增收加班费。
十二、船舶在工厂修理期间，其因修换而拆下的旧件、旧料，均归船厂所有。
服务项目一、船舶靠离码头系解缆二、码头费以船长每米24小时一天计，不足一天按一天计算。
每天每米5元注:特殊船型价格另计.三、消防值班：以一天24小时计，不足一天按一天计算.每天每人：85元四、消防巡回检查:以一天24小时计，不足一天按一天计算。
五、接拆电缆、水管：(1)电缆接拆一次:138元（2)水管接拆一次：102元（3）消防软管接拆一次102元六、清除生活垃圾船长100米以下：40元／天船长100米以上：70元／天七、临时放置消防器材:每只：50元／天八、供淡水、供电:按当地实际情况计价.九、测爆:2、厂区外测爆交通费另计.十、引水费：根据各厂实际情况计价。
民用船舶修理价格表
民用船舶修理价格表1. 清洗与涂漆：- 小型船舶 (10米以下)：500-1000元- 中型船舶 (10-20米)：1000-2000元- 大型船舶 (20米以上)：2000-5000元2. 电力系统修复：- 电缆更换：500-1000元- 蓄电池更换：200-500元- 发电机修理：500-1000元3. 发动机与传动系统维修：- 发动机故障检修：500-1500元- 排气系统维修：200-500元- 传动系统维修：500-1500元4. 船体与船底维修：- 破损修补：500-2000元- 钢琴漆磨光和涂漆：500-1000元- 确认船底防腐涂料：500-1000元5. 冷却系统和水泵修理：- 水泵更换：500-1000元- 冷却系统清洗：200-500元- 冷却系统更换零件：200-500元6. 船舶电子设备修理：- GPS修理：200-500元- 雷达修理：500-1000元- 航向仪修理：200-500元以上价格仅供参考，具体修理费用可能因船舶型号、维修项目和修理工作量的不同而有所变动。
建议在修理前与船坞或修理厂取得书面报价。
同时，也建议定期进行船舶检查和维护，以避免大修和高额费用的发生。
民用船舶修理是保障船只安全和良好运行的重要环节。
在航海过程中，由于船只长时间暴露在海水和恶劣的环境条件下，船体和船上设备会受到损坏和磨损。
及时修理和维护可以延长船只的使用寿命，确保船舶运营的可靠性和安全性。
因此，船舶修理成为船主和船舶运营者不可避免的费用。
船舶修理价格表中列出了一些常见的修理项目和对应价格范围。
首先是清洗与涂漆。
船只长时间在海上行驶，船体容易积聚污垢和藻类，需要定期清洗和涂漆以保持船体的外观和防腐效果。
根据船舶大小，清洗与涂漆的价格会有所不同。
电力系统是船舶正常运行所必需的，电缆和蓄电池的损坏可能导致船只停电或无法启动。
相关修理项目包括电缆更换、蓄电池更换以及发电机的修理。
费用的区间取决于修理的规模和所需材料的成本。
(完整版)国内民用船舶修理价格表(92黄本)
国内民用舶舶修理价格表中国船舶工业总公司一九九二年关于颁发《国内民用船舶修理价格表》(一九九二年本）的通知船总修[1992] 1374 号各有关单位：中国船舶工业总公司一九九二年编制的《国内民用船舶修理价格表》(以下简称一九九二年黄皮本）业经批准，自一九九二年十月一日起正式执行，特通知如下：一、中国船舶工业总公司自一九八六年颁发的《国内民用船舶修理价格表》以来，对承接国内修船业务及宏观调控方面都起到了良好的作用。
由于目前修船成本比五、六年前有较大幅度的提高，而该本一直未作修改，已不适用于目前修船市场的要求。
"一九九二年黄皮本"是根据当前修船市场的情况与各厂近年来的实际报价水平，经调查研究后制订的。
二、该本（一九九二年黄皮本）是中国船舶工业总公司系统所属船厂对国内民用船舶（特种船舶的修理除外）修理统一开价标准的依据。
三、本公司系统所属船厂可按各自情况，在该本（一九九二年黄皮本）计价标准的基础上，允许上下浮动百分之十范围内对外开价。
四、原一九八六年颁发的《国内民用船舶修理价格表》及船总修(199l) 2041号文《关于对国内民用船舶修理价格调整的通知》均自一九九二年十月一日起停止使用。
五、该本（一九九二年黄皮本）的版权和解释权属中国船舶工业总公司，未经许可，不准重版与翻印。
中国船舶工业总公司一九九二年七月九日目录《国内民用船舶修理价格表》使用说明－－－－－－（１）服务项目一、船舶靠离码头系解缆－－－－－－－－－－－（３）二、码头费－－－－－－－－－－－－－－－－－（３）三、消防值班－－－－－－－－－－－－－－－－（４）四、消防巡回检查－－－－－－－－－－－－－－（４）五、接拆电缆、水管－－－－－－－－－－－－－（４）六、清除生活垃圾－－－－－－－－－－－－－－（４）七、临时放置消防器材－－－－－－－－－－－－（５）八、供淡水、供电－－－－－－－－－－－－－－（５）九、测爆－－－－－－－－－－－－－－－－－－（５）十、引水费－－－－－－－－－－－－－－－－－（５）十一、搭拆上下船扶梯－－－－－－－－－－－－－（５）十二、临时通风设备的设置－－－－－－－－－－－（６）十三、坞底临时照明设备的设置－－－－－－－－－（６）十四、舱底污水及污油水抽出－－－－－－－－－－（６）十五、供冰机冷却水－－－－－－－－－－－－－－（６）十六、供蒸汽上船－－－－－－－－－－－－－－－（６）十七、安装临时电话上船－－－－－－－－－－－－（６）坞修工程一、进出坞及在坞－－－－－－－－－－－－－－（７）二、尾轴工程－－－－－－－－－－－－－－－－（９）三、舵系工程－－－－－－－－－－－－－－－（１１）四、海底阀研磨－－－－－－－－－－－－－－（１３）五、人孔道门拆装－－－－－－－－－－－－－（１４）六、船底塞拆装－－－－－－－－－－－－－－（１４）七、锌板换新－－－－－－－－－－－－－－－（１４）钢质工程一、钢质焊接结构船体平直外板换新－－－－－（１５）二、舷外搭拆脚手架－－－－－－－－－－－－（１６）三、油、水舱压水试验或气密试验－－－－－－（１６）四、钢板测厚－－－－－－－－－－－－－－－（１７）起货设备起货设备－－－－－－－－－－－－－－－－－（１８）油漆工程一、船名、港籍、水尺、干舷圈描写－－－－－（１９）二、船体外部除锈油漆－－－－－－－－－－－（２０）三、货舱除锈油漆－－－－－－－－－－－－－（２１）四、甲板除锈油漆－－－－－－－－－－－－－（２１）五、高油、水舱及双层底油水舱除锈油漆－－－（２２）六、机、炉舱花铁板上、下除锈油漆－－－－－（２３）七、上层建筑室内、外、顶部及围壁除锈油漆－（２３）锚、锚链工程锚及锚链工程－－－－－－－－－－－－－－－（２４）轮机工程轮机工程说明－－－－－－－－－－－－－－－－（２５）一、主机工程１、气缸盖拆装－－－－－－－－－－－－（２７）２、进排气阀拆装－－－－－－－－－－－（２８）３、气缸盖附属阀拆装－－－－－－－－－（２９）４、筒型活塞拆装－－－－－－－－－－－（３０）５、十字头式活塞拆装－－－－－－－－－（３１）６、活塞解体试压－－－－－－－－－－－（３２）７、十字头轴承、连杆大端轴承拆装－－－（３３）８、气缸套拆装－－－－－－－－－－－－（３４）９、高压燃油泵、喷油器拆装－－－－－－（３５）１０、空气分配器拆装－－－－－－－－－－（３５）１１、主轴承拆装－－－－－－－－－－－－（３６）１２、曲拐轴拐档差测量－－－－－－－－－（３７）１３、推力轴承拆装－－－－－－－－－－－（３７）１４、船舶预试航、调整试车、系泊试验－－（３８）二、付机工程－－－－－－－－－－－－－－－（３９）三、离心泵１、卧式离心泵－－－－－－－－－－－－（４０）２、立式离心泵－－－－－－－－－－－－（４１）四、卧式齿轮泵－－－－－－－－－－－－－－（４２）五、螺杆泵－－－－－－－－－－－－－－－－（４３）六、空压机－－－－－－－－－－－－－－－－（４４）七、制冷压缩机－－－－－－－－－－－－－－（４５）八、热交换器清洗－－－－－－－－－－－－－（４６）九、管路低压阀门－－－－－－－－－－－－－（４７）十、锅炉安全阀－－－－－－－－－－－－－－（４８）十一、管路拆装换新－－－－－－－－－－－－－（４９）十二、起货机－－－－－－－－－－－－－－－－（５１）十三、立式电动绞缆机－－－－－－－－－－－－（５２）十四、起锚机－－－－－－－－－－－－－－－－（５３）电气部分一、交流电动机小修－－－－－－－－－－－－（５４）二、交流发电机小修－－－－－－－－－－－－（５５）三、发电机用盐水缸设备作负荷试验－－－－－（５６）四、配电屏自动空气断路器保护装置校验－－－（５７）五、各类电表校验－－－－－－－－－－－－－（５８）六、配电屏清洗、紧固螺丝－－－－－－－－－（５９）七、电缆拆装与新装－－－－－－－－－－－－（６０）中国船舶工业总公司船舶修理暂行基本条款－－－（６１）常用金属材料比重表－－－－－－－－－－－－－（６６）常用非金属材料比重表－－－－－－－－－－－－（６７）《国内民用船舶修理价格表》使用说明一、本《价格表》系参照我中国船舶工业总公司系统各船厂的历史资料并结合修船产品实际情况和现行市场价格水平，经测算整理汇编成册，供我总公司系统各单位使用。
（完整版）国内民用船舶修理价格表（92黄本）
（完整版）国内民用船舶修理价格表（92黄本）国内民用舶舶修理价格表中国船舶工业总公司一九九二年关于颁发《国内民用船舶修理价格表》(一九九二年本）的通知船总修[1992] 1374 号各有关单位：中国船舶工业总公司一九九二年编制的《国内民用船舶修理价格表》(以下简称一九九二年黄皮本）业经批准，自一九九二年十月一日起正式执行，特通知如下：一、中国船舶工业总公司自一九八六年颁发的《国内民用船舶修理价格表》以来，对承接国内修船业务及宏观调控方面都起到了良好的作用。
由于目前修船成本比五、六年前有较大幅度的提高，而该本一直未作修改，已不适用于目前修船市场的要求。
"一九九二年黄皮本"是根据当前修船市场的情况与各厂近年来的实际报价水平，经调查研究后制订的。
二、该本（一九九二年黄皮本）是中国船舶工业总公司系统所属船厂对国内民用船舶（特种船舶的修理除外）修理统一开价标准的依据。
三、本公司系统所属船厂可按各自情况，在该本（一九九二年黄皮本）计价标准的基础上，允许上下浮动百分之十范围内对外开价。
四、原一九八六年颁发的《国内民用船舶修理价格表》及船总修(199l) 2041号文《关于对国内民用船舶修理价格调整的通知》均自一九九二年十月一日起停止使用。
五、该本（一九九二年黄皮本）的版权和解释权属中国船舶工业总公司，未经许可，不准重版与翻印。
中国船舶工业总公司一九九二年七月九日目录《国内民用船舶修理价格表》使用说明－－－－－－（１）服务项目一、船舶靠离码头系解缆－－－－－－－－－－－（３）二、码头费－－－－－－－－－－－－－－－－－（３）三、消防值班－－－－－－－－－－－－－－－－（４）四、消防巡回检查－－－－－－－－－－－－－－（４）五、接拆电缆、水管－－－－－－－－－－－－－（４）六、清除生活垃圾－－－－－－－－－－－－－－（４）七、临时放置消防器材－－－－－－－－－－－－（５）八、供淡水、供电－－－－－－－－－－－－－－（５）九、测爆－－－－－－－－－－－－－－－－－－（５）十、引水费－－－－－－－－－－－－－－－－－（５）十一、搭拆上下船扶梯－－－－－－－－－－－－－（５）十二、临时通风设备的设置－－－－－－－－－－－（６）十三、坞底临时照明设备的设置－－－－－－－－－（６）十四、舱底污水及污油水抽出－－－－－－－－－－（６）十五、供冰机冷却水－－－－－－－－－－－－－－（６）十六、供蒸汽上船－－－－－－－－－－－－－－－（６）十七、安装临时电话上船－－－－－－－－－－－－（６）坞修工程一、进出坞及在坞－－－－－－－－－－－－－－（７）二、尾轴工程－－－－－－－－－－－－－－－－（９）三、舵系工程－－－－－－－－－－－－－－－（１１）四、海底阀研磨－－－－－－－－－－－－－－（１３）五、人孔道门拆装－－－－－－－－－－－－－（１４）六、船底塞拆装－－－－－－－－－－－－－－（１４）七、锌板换新－－－－－－－－－－－－－－－（１４）钢质工程一、钢质焊接结构船体平直外板换新－－－－－（１５）二、舷外搭拆脚手架－－－－－－－－－－－－（１６）三、油、水舱压水试验或气密试验－－－－－－（１６）四、钢板测厚－－－－－－－－－－－－－－－（１７）起货设备起货设备－－－－－－－－－－－－－－－－－（１８）油漆工程一、船名、港籍、水尺、干舷圈描写－－－－－（１９）二、船体外部除锈油漆－－－－－－－－－－－（２０）三、货舱除锈油漆－－－－－－－－－－－－－（２１）四、甲板除锈油漆－－－－－－－－－－－－－（２１）五、高油、水舱及双层底油水舱除锈油漆－－－（２２）六、机、炉舱花铁板上、下除锈油漆－－－－－（２３）七、上层建筑室内、外、顶部及围壁除锈油漆－（２３）锚、锚链工程锚及锚链工程－－－－－－－－－－－－－－－（２４）轮机工程轮机工程说明－－－－－－－－－－－－－－－－（２５）一、主机工程１、气缸盖拆装－－－－－－－－－－－－（２７）２、进排气阀拆装－－－－－－－－－－－（２８）３、气缸盖附属阀拆装－－－－－－－－－（２９）４、筒型活塞拆装－－－－－－－－－－－（３０）５、十字头式活塞拆装－－－－－－－－－（３１）６、活塞解体试压－－－－－－－－－－－（３２）７、十字头轴承、连杆大端轴承拆装－－－（３３）８、气缸套拆装－－－－－－－－－－－－（３４）９、高压燃油泵、喷油器拆装－－－－－－（３５）１０、空气分配器拆装－－－－－－－－－－（３５）１１、主轴承拆装－－－－－－－－－－－－（３６）１２、曲拐轴拐档差测量－－－－－－－－－（３７）１３、推力轴承拆装－－－－－－－－－－－（３７）１４、船舶预试航、调整试车、系泊试验－－（３８）二、付机工程－－－－－－－－－－－－－－－（３９）三、离心泵１、卧式离心泵－－－－－－－－－－－－（４０）２、立式离心泵－－－－－－－－－－－－（４１）四、卧式齿轮泵－－－－－－－－－－－－－－（４２）五、螺杆泵－－－－－－－－－－－－－－－－（４３）六、空压机－－－－－－－－－－－－－－－－（４４）七、制冷压缩机－－－－－－－－－－－－－－（４５）八、热交换器清洗－－－－－－－－－－－－－（４６）九、管路低压阀门－－－－－－－－－－－－－（４７）十、锅炉安全阀－－－－－－－－－－－－－－（４８）十一、管路拆装换新－－－－－－－－－－－－－（４９）十二、起货机－－－－－－－－－－－－－－－－（５１）十三、立式电动绞缆机－－－－－－－－－－－－（５２）十四、起锚机－－－－－－－－－－－－－－－－（５３）电气部分一、交流电动机小修－－－－－－－－－－－－（５４）二、交流发电机小修－－－－－－－－－－－－（５５）三、发电机用盐水缸设备作负荷试验－－－－－（５６）四、配电屏自动空气断路器保护装置校验－－－（５７）五、各类电表校验－－－－－－－－－－－－－（５８）六、配电屏清洗、紧固螺丝－－－－－－－－－（５９）七、电缆拆装与新装－－－－－－－－－－－－（６０）中国船舶工业总公司船舶修理暂行基本条款－－－（６１）常用金属材料比重表－－－－－－－－－－－－－（６６）常用非金属材料比重表－－－－－－－－－－－－（６７）《国内民用船舶修理价格表》使用说明一、本《价格表》系参照我中国船舶工业总公司系统各船厂的历史资料并结合修船产品实际情况和现行市场价格水平，经测算整理汇编成册，供我总公司系统各单位使用。
《国内民用船舶修理价格表》
《国内民用船舶修理价格表》使用说明一.本价格表的计价货币为人民币。
二•本价格表仅适用于正常工作时间，即每周5天，每天8小时工作制，应船方要求的法定假日船厂假日中的修理，将按加班收费。
三. 本价格表仅适用在船厂厂区内施工，在非厂区及港内装卸货码头、浮筒、锚地等施工费用，将按具体工程场合提价。
四. 船舶在船厂修理期间，非经船厂同意，不允许安排非船厂劳动力进船厂担任修理工作。
五. 本价格表的计价原则：凡在两档之间者均按高一档价格计算。
各部分的系数，凡遇多个同时出现时，应将系数相加后计算。
六. 除了重要机械部份、螺旋桨和尾轴之外，所有在修船中拆卸的废旧料，全部归船厂所有。
七. 本价格表仅适用于运输船舶之修理，其他船舶之修理不属本价格表范围。
八. 本价格表自1996年1月1日起生效，如遇材料价格变化等原因，我公司保留调整开价权利，调整时不另行通知。
服务项目码头费：5000总吨以下：每天1000元5001总吨至20000总吨：每天每总吨0.20元大于20000总吨：每天4000元+ (总吨-20000 )x 0.16元船舶靠离码头系解缆:注。
三•接拆电缆、水管:(1) 电缆接拆一次：320 元(2) 水管接拆一次：200 元(3) 消防软管接拆一次：200 元四.供冰机冷却水每天每路：270 元接拆冰机冷却水管路每路每次：200元五•供淡水、供电：按当地实际情况计价。
六•供压载舱压载水费:接拆水管一次：供压载水每吨：200元2.50 元七.消防值班：每天每人：85 元不足一天按一天计算临时放置消防器材：5000总吨以下：每艘5000总吨以上：每艘800元1200 元八•清除生活垃圾：每天150元九•供压缩空气费：接拆管路一次：供气（8小时计价）200 元每路266元十•供蒸汽费：接拆管路一次：供气（每小时计价）1328 元每路120元:电话费拆装电话: 使用电话:每台150元每台每天10元注：国内、国际长途费另计十二•临时通风设备的设置：每班每台：240元十三．供电加热器费：每套安装费：33每套每天维持费：33 元十四．测爆：油轮：每艘次600 元其它船舶：每艘次320 元厂区外测爆交通费另计。
《国内民用船舶修理价格表》使用说明92黄本解读
《国内民用船舶修理价格表》使用说明（92黄本）1. 本《价格表》系参照我中国船舶工业总公司系统各船厂的历史资料并结合修船产品实际情况和现行市场价格水平，经测算整理汇编成册，供我公司系统各单位使用。
2. 本《价格表》仅适用于民用常规船舶的修理。
3. 本《价格表》中已包括材料的项目，其材料费是按91年现行价格测算的，如遇材料市场价格有较大变动时，各厂按实际情况适当调整其差价部分。
4. 本《价格表》中各分项说明中均已明确修换范围，其他附带工程及可能产生的零部件换新以及施工工艺所需的专用工具、模具、胎架、专用设备等费用另计。
5. 凡单一性技术劳动，如柴油机的喷油器、高压油泵、调速器、冰机、空调等的修理价格可作适当上浮。
6. 本《价格表》所列的各档规格，凡在两档之间者均按高一档价格计。
7. 本《价格表》中各部分的系数，凡遇多个同时出现时，应将系数相加后计算。
8. 本《价格表》所列之价格，均系出厂价格。
9. 凡工厂委托外单位加工、借用设备、外购器材等，应按工厂实际支付费用加上运杂费、管理费及法定利润、税金。
10. 本《价格表》之价格仅适用于厂区作业，离厂区作业及出差施工价格另计。
11. 本《价格表》适用于正常工作日的日班作业，若船方要求特急需逾时加班者，则应增收加班费。
12. 船舶在工厂修理期间，其因修换而拆下的旧件、旧料，均归船厂所有。
六、清除生活垃圾，船长100米以下40元/天服务项目、船舶靠离码头系解缆：元次（注：下列价格不包括拖轮费）二、码头费：以船长每米24小时一天计，不足一天按一天计算，每天每米：5元（注：特殊船型价格另计）三、消防值班：以一天24小时计，不足一天按一天计算，每天每人：85元四、消防巡回检查：以一天24小时计，不足一天按一天计算。
元/天五、接拆电缆、水管：1电缆接拆一次：138元2、水管接拆一次：102元3、消防软管接拆一次：102元船长100米以上70元/天七、临时放置消防器材：50元/只八、供淡水、供电：按当地实际情况计价注：船舶进厂后局部测爆每次每处元；厂区外测爆交通费另计十、引水费：根据各厂实际情况计价。
船舶修理项目报价单
水线以下做环氧紫红面漆二度
⑷
甲板防锈漆一度，甲板防滑漆二度
⑸
顶棚做一底二面棚子清理破裂的腻子，打磨补齐环氧腻子，进行多遍补平磨光，再喷聚氨酯可复涂白色漆三度
⑴
该项环氧腻子及油漆材料费
⑵
清理刮灰打磨喷漆劳务费
勘划船名及标色
左右舷轮胎护靠更换
室内局部整理，驾驶室右侧面已坏，不能打开，进行拆修，左侧门保养调整
舵杆传动钢丝绳更换，所有的滑轮检查保养
机舱后棚后部变形，拆修棚架，更换棚顶板
机舱内主机按二级保养要求进行保养，调整气门，油泵调试，更换三滤和机油
⑴
机配件
⑵
修理费
齿轮箱保养修理
⑴
机配件
⑵
修理费
尾轴检查，更换前后油封水封，检查铜套磨损情况，视情况更换
海底箱、过滤器、海底阀进行检查清理，做密性实验
船舶修理项目报价单
单位：南通公安局港闸分局
船舶名称：公安
工程名称：上坡修理第页
序号
工程内容
单位
数量
项目价格
单价
合计
机舱油箱清洗
舵系检查，更换下舵承油封
沙发更换人造革面皮
前客舱更换防滑垫
玻璃窗检查，老化的橡皮密封条更换
更换海水泵一台
更换电瓶只
只
总计
报价单位：
时间：年月日
船舶修理项目报价单
单位：南通公安局港闸分局
船舶名称：公安
工程名称：上坡修理第页
序号
工程内容
单位
数量
项目价格
单价
合计
一
船舶简况
船长，船宽，型深，主机一台，齿轮箱为一台，本次上坡修理。
二
修理项目
《国内民用船舶修理价格表92黄本》
资料范本本资料为word版本，可以直接编辑和打印，感谢您的下载《国内民用船舶修理价格表92黄本》地点：__________________时间：__________________说明：本资料适用于约定双方经过谈判，协商而共同承认，共同遵守的责任与义务，仅供参考，文档可直接下载或修改，不需要的部分可直接删除，使用时请详细阅读内容《国内民用船舶修理价格表》使用说明本《价格表》系参照我中国船舶工业总公司系统各船厂的历史资料并结合修船产品实际情况和现行市场价格水平，经测算整理汇编成册，供我总公司系统各单位使用。
本《价格表》仅适用于民用常规船舶的修理。
海洋钻井平台、工程船舶及其它特种船舶中的特殊设施修理价格另计。
本《价格表》中已包括材料的项目，其材料费是按91年现行价格测算的，如遇材料市场价格有较大的变动时，各厂可按实际情况适当调整其差价部分。
本《价格表》各分项说明中均已明确修换范围，其附带工程及可能的零部件换新以及施工工艺所需的专用工具、模具、胎架、专用设备等费用另计。
凡单一性技术劳务，如柴油机的喷油器、高压油泵、调速器、冰机、空调等的修理价格可作适当上浮。
本《价格表》所列的各档规格，凡在两档之间者均按高一档价格计。
本《价格表》中各部分的系数，凡遇多个同时出现时，应将系数相加后计算。
本《价格表》所列价格，均系出厂价格。
凡工厂委托外单位加工、借用设备、外购器材等，应按工厂实际费用加上运杂费、管理费及法定利润、税金。
本《价格表》之价格仅适用于厂区作业，离厂区作业及出差施工其价格另行计算。
本《价格表》适用于正常工作日的日班作业，若船方要求特急，需逾时加班者，则应增收加班费。
船舶在工厂修理期间，其因修换而拆下的旧件、旧料，均归船厂所有。
服务项目一、船舶靠离码头系解缆元／次注：上述价格不包括拖轮费二、码头费以船长每米24小时一天计，不足一天按一天计算。
每天每米5元注：特殊船型价格另计。
三、消防值班：以一天24小时计，不足一天按一天计算。
《国内民用船舶修理价格表》
《国内民用船舶修理价格表》使用说明一．本价格表的计价货币为人民币。
二．本价格表仅适用于正常工作时间，即每周5 天，每天8 小时工作制，应船方要求的法定假日、船厂假日中的修理，将按加班收费。
三．本价格表仅适用在船厂厂区内施工，在非厂区及港内装卸货码头、浮筒、锚地等施工费用，将按具体工程场合提价。
四．船舶在船厂修理期间，非经船厂同意，不允许安排非船厂劳动力进船厂担任修理工作。
五．本价格表的计价原则：凡在两档之间者均按高一档价格计算。
各部分的系数，凡遇多个同时出现时，应将系数相加后计算。
六．除了重要机械部份、螺旋桨和尾轴之外，所有在修船中拆卸的废旧料，全部归船厂所有。
七．本价格表仅适用于运输船舶之修理，其他船舶之修理不属本价格表范围。
八．本价格表自1996年1月1日起生效，如遇材料价格变化等原因，我公司保留调整开价权利，调整时不另行通知。
服务项目一．码头费：5000 总吨以下：每天1000 元5001 总吨至20000总吨：每天每总吨0.20 元大于20000总吨：每天4000元+(总吨-20000) X 0.16元二. 船舶靠离码头系解缆：注：上述价格不包括拖轮费三•接拆电缆、水管：(1)电缆接拆一次：320元(2)水管接拆一次：200元(3)消防软管接拆一次：200元四•供冰机冷却水每天每路：270元接拆冰机冷却水管路每路每次：200元五•供淡水、供电：按当地实际情况计价。
六•供压载舱压载水费：接拆水管一次：200元供压载水每吨： 2.50元七•消防值班：每天每人：85元不足一天按一天计算临时放置消防器材：5000 总吨以下：每艘800 元5000 总吨以上：每艘1200元八．清除生活垃圾：每天150 元九．供压缩空气费：接拆管路一次：200 元供气（8 小时计价）：每路266元十．供蒸汽费：接拆管路一次：1328 元供气（每小时计价）每路120 元十一．：电话费拆装电话：每台150 元使用电话：每台每天10 元注：国内、国际长途费另计十二．临时通风设备的设置：每班每台：240 元十三．供电加热器费：每套安装费：33 元每套每天维持费：33 元十四．测爆：油轮：每艘次600 元其它船舶：每艘次320 元厂区外测爆交通费另计。
修船价格蓝本
船舶修理价格表TARIFF FOR SHIP REPAIRS中国船舶工业总公司CHINA STATE SHIPBUILDING CORPORATIONGENERAL NOTES1. The rates quoted herein are in US dollar $.2. The rates are applicable to the work carried out during the normal workinghour, that is five working days a week, and sixteen hours a day. Any works done outside these hours or on Saturdays and Sundays, National Holidays and yard's holidays shall be charged with extra for overtime, ship on voyage repair will be priced extra.3. All prices quoted herein are for ship repairs carried out in the premisesof the shipyard, extra price should be added for such repairs carried out at the port berths, buoys, anchorages according to the actual work to be done.4. Any vessel during the repair period of repair in the yard, unless agreed bythe yard, the Customer shall not be permitted to employ any labor other than the yard to perform repairs.5. The yard shall not be responsible for the consequences of war, earthquakeor causes beyond yard's control.6. All scrapped material except heavy parts of machinery, propeller andtailshafts shall be the yard's property.7. This tariff is applicable to the repair of freight carriers only, repairsof other types of ship are beyond of this tariff scope.8. This tariff becomes effective from January 1st, 1991, subject to revised pricedepending on the change in material cost etc. without notice.CONTENTS1.General Services page1.Wharfage 12.Mooring and unmooring 13.Shore electric power supply 14.Cooling water supply 15.Fresh water supply 16.Water to ballast tank 17.Fire precautions 28.Garbage disposal 2pressed air supply 210.Steam supply 211.Telephone service 212.Ventilation fan 213.Heating lamp for electric motor 214.Gas free inspection 215.Rental of crane 216.Drain pipes 317.Gangway for ship mooring 318.Shipyard pilotage 32.Docking Works1.Docking charges 42.Tugs charges 43.Tailshaft 54.Rudder 65.Underwater works 7(1)Sea chests 7(2)Sea valves 8(3)Zinc anodes 8(4)Bottom plugs 8 3.Hull Department1.Cleaning and painting 9(1)Marks repainting 9(2)Hull cleaning 9(3)Painting 9(4)Scraping and chipping 10(5)Gritblasting 10(6)Staging 10 2.Anchors and chain cables 11(1)Anchor chain cable 11(2)Chain blocker 113.Steel work 12(1)Renewal 12(2)Handrail fence 13(3)Hatch cover, watertight door, manhole cover 134.Tank work(1)Cleaning 13(2)Chipping and mud removal 14(3)Test 145.Derrick union 15 4.Machinery Works1.Diesel engine 162.Turbo charger 183.Heating exchanger 184.Aux. Boiler 195.Pipe 206.Valve 21 5.Electric Works1.Motor 222.Generator 22General Service1.WharfageLess than 5000 GRT 125 per day 5001 to 20,000 GRT 0.025 per gross ton per day Over 20,000 GRT 500 + (Gross ton – 20000) x 0.02 per day2.Mooring and unmooring (per time)Up to 5,000 GRT 800 5,001 to 10,000 GRT 1,120 10,001 to 20,000 GRT 1,56020,001 to 30,000 GRT 2,05030,001 to 40,000 GRT 2,60040,001 to 50,000 GRT 3,20050,001 to 60,000 GRT 3,900Over 60,000 GRT 4,700Note:(1)Above ratesat normal working hours on shipyard’s premises for mooring and unmooring.(include Towage service)(2)Above ratesincluding line handling.(3)In case ofovertime, extra 30% shall be charged.(4)If ownerschange the towing plan, unless there is timelynotice to shipyard, extra 50% shall be charged for waiting.3.Shore electric powerConnection and disconnection of cable 100 per time Current, per K.W.H. (AC) 0.20 4.Cooling water supply to food refrigeratorLine to connect and disconnect 40 per time per line Water supply 40 per day per line 5.Fresh water supplyLine to connect and disconnect 40 per time per line From shore 1.00 per ton (Prices are separately charged from barge)6.Water to ballast tank (sea and river water)Line to connect and disconnect 40 per time per lineSupply of water 0.40 per ton7.Fire precautionsPut fire extinguishers 10 per dayFire line to connect and disconnect 40 per time per lineKeep pressure 20 per day per lineFire watch, per man (24 hours) 120 per day8.Galley garbage disposal30 per daypressed air supplyLine connection and disconnection 40 per time per lineTo supply 40 per day (8 Hours)10.Steam supplyLine connection and disconnection 200 per time per lineTo supply 20 per hour11.TelephoneserviceTelephone wire connect and disconnect 30 per time4 per set, per day(Toll calls to be extra)12.Ventilationfan15 per set per day13.Heating lampfor electric motrorInstallation 5 per setMaintenance 5 per set, per day14.Gas freeinspectionTanker 80 per timeOther vessel 40 per time15.Rental ofcrane(1)Shore craneLess than 30 ton 90 per hour(2)F loating craneLess than 30 ton 90 per hour50 ton 150 per hourover 50 ton extra Note:(1)Any fractionof one hour shall be charged as one full hour.(2)Floatingcrane price excludes tuggage price.(3)At shipyardoutside service, price shall be charged extra.16.Connectionof sewage water drain pipes and grooves20 per pc17.Ship mooringgangway ladder on and off (per time)Less than 5000 gross ton 250Less than 10000 gross ton 350Less than 20000 gross ton 500Over 20000 gross ton extra18. Shipyard pilotage chargedUp to 20000 GRT 800 Up to 40000 GRT 1000Up to 60000 GRT 1200I.Docking works1.Dock chargesNote:(1)Floatingdocks extra 10% to be added.(2)Above ratesexcluded towage service and line handlers for docking and undocking.(3)Minimumcharge will be calculated on the basis of 48 hours. Any fraction of one subsequent day shall be counted as one full day.(4)Any vesselhaving gross tonnage less than of 60% her deadweight, shall be charged with dockage calculated as if her gross tons were of 60% thedeadweight.(5)When thevessel with cargo onboard is allowed to drydock weight of the cargo onboard shall be added to gross tonnage of the vessel.(6)Specialvessel shall be charged extra.(7)Extracharges shall be paid when: remove and replace keel blocks for access to repair USD75 per each, side blocks for access to repair USD50 per each.(8)Lossincurred, if any, may be claimed for, compensation against abruptcancellation after shipyard made all necessary preparation for thedocking2.Tuggage (per tug boat/shifting)Note:(1)Above ratesat normal working time, all overtime and national holidays, extra 30%shall be charged.(2)Towageservices as required for other work shall be charged by 0.15/HP.hour. Above tug boat price are all net price.3.Tailshaft(1) Conventional service------draw of tailshaft, for examination, measure,and recording, rope guard to remove, propeller to disconnect andtailshaft to draw, including removal of one intermediate shaft, bearing and cooling water pipe, in shaft alley, stern gland to repack with owner supplied packing, upon completion to reinstall.Note:(1)Above priceincludes necessary staging.(2)Thefollowing items shall be charged extra:Shaft alignment adjustment.Filling with tallow in propeller bonnet and bossRenewal of water seal rubber ringMagnaflux test on tailshaft coneRemoval and replacement of miscellaneous fittings in engineroom and shaft alley, such as handrails and cables, etc.Any repair and / or renewal.Tailshaft and / or propeller to workshop.(3)Above pricediameter of tailshaft means diameter of the brass sleeves.(4)Controllable pitch propeller shaft to be considered separately.(5)Due totailshaft, intermediate shaft, main thrust shaft removal, necessary removal hull plate extra charge.(6)40% of priceof the above will be charged in case of disconnecting only propeller.(2) Remove rope guard and measure stern tube bearing wear-down and renewalwith owner supplied packing.(4) Cleaning the propellerNote:(1)In case 5blades, 20% up; 6 blades, 30% up.(2)Above pricestaging shall be extra.4.Rudder(1) Check and record rudder pintle clearance in place(including staging and removal of inspection plate)(2) Renewal rudder gland packing supplied by owner (ordinary type)(3) Rudder lift up, to disconnect steering gear, lift up rudder for checking clearance and then close.Note:(1)Simplex rudder, hanging rudder and AEG type to be charged with extra20%(2)Ruder rod and rudder blade removal to be extra.(3)All spares to workshop repair charged with extra.5.Underwater work(1) Sea chest:Removal strainer, clean, one coat paint and close on completion.area per eachUp to 0.5 sqm 70Over 0.5 sqm 120Note:(1)Above priceexcluding any repair, renewal and staging.(2)Paint supplyby owners.(2)S ea valveOpen up sea valves for survey, grind in, clean and paint,(owner supply) renew packing, repack and close in place.Note:(1)Renewal ofvalve (with owner’s valve), 80% of above tariff.(2)Valve toworkshop for repair, 150% of above tariff.(3)Any renewaland repair will be charged separately.(3) Zinc and hull anodes(1) Renewal with owner’s materialless than 10 kg 13 per pc10 ~ 25 kg 16 per pcover 25 kg 20 per pc(2) Renewal with yard’s material per pcsize 300 x 150 x 30mm 58 per pcstaging price to be charged extraNote:(1)Double tankand ballast tank zinc anode renewal (owner supply) add 30% abovetariff.(2)Stagingprice to be extra.(4) Bottom plugsRemoval and refitting (including cement-washing) per pc 18(any repair and renewal and staging will be charged separately)III. Hull Department1 Cleaning and painting(1) Marks RepaintingNote:(1)Stagingshall be extra.(2)Paints to besupplied by owner.(3)Above pricewill be only applicable to work carried out in dock.(2) Hull cleaning ( Per sq.m.)High pressure water washing (pressure over 200kg/sq.cm)0.80Washing down with fresh water 0.30Removal of oily spots 4.00Note:(1)Under 300sq.m, price shall be charged extra.(2)Stagingshall be extra.(3) Painting (Per sq.m.)Note:(1)Stagingshall be extra.(2)Paintssupplied by owner.(3)If coatingsof bitumen paint are required, extra shall be charged with addition of 20%, if coating SPC thickness 75 micron add 50% charge, over 75micron shall be extra.(4) Scraping and Chipping (per sq.m.)Note:(1) Prices for surface area in dirty condition shall be charged extra.(2) Staging shall be extra.(3)Other tankwork shall be charged extra.(5) Gritblasting (per sq.m.)Note:(1)Spotblasting (hull up to 300sq.m., hold up to 500sq.m. per hold) shall be chargedwith extra 50% of above price.(2)Excludingnecessary staging and any other accessary work.(3)For doubletank above price extra charged.(4)Surface areain dirty condition to be charged extra.(5)Mechanicalscaling before Gritblasting, price shall extra.(6) Staging (actual length / per meter)Outside shell 4In cargo hold 5In engine room 6Note:(1)Under 30 M,additional 50% of above to be charged.(2)Prices forin-side, difficult area such as internal tank, hold, etc. to be charged extra 100%.(3)At thesupperstructure, mast, etc. high position, to be charged extra.(4)Usehydraulic crane working 50USD per hour per set.2.Anchors, anchor cables (port and stb’d)(1)ranginganchors and cables, port abd stb’d sides, wash down chain cables with fresh water, light scraping and chipping, apply one coat with owner’s supplied paint and restore. Unshackling, and reshackling, measure chain cables diameter and reversing marking and close up on completion.Note:(1)Range downand clean, measure and close up on completion excluding chainreversing, overhaul of shackles, marking, painting.(2)All paintsand bitumen will be supplied by owner(3)Unshacklingand reshackling per piece 20. reversing per piece 120.(2)Chain locker(port and stb’d) clean, apply one coat with owner’s supplied paint and bitumen.。
《国内民用船舶修理价格表》92黄本
《国内民用船舶修理价格表》使用说明1.本《价格表》系参照我中国船舶工业总公司系统各船厂的历史资料并结合修船产品实际情况和现行市场价格水平，经测算整理汇编成册，供我公司系统各单位使用。
2.本《价格表》仅适用于民用常规船舶的修理。
3.本《价格表》中已包括材料的项目，其材料费是按91年现行价格测算的，如遇材料市场价格有较大变动时，各厂按实际情况适当调整其差价部分。
4.本《价格表》中各分项说明中均已明确修换范围，其他附带工程及可能产生的零部件换新以及施工工艺所需的专用工具、模具、胎架、专用设备等费用另计。
5.凡单一性技术劳动，如柴油机的喷油器、高压油泵、调速器、冰机、空调等的修理价格可作适当上浮。
6.本《价格表》所列的各档规格，凡在两档之间者均按高一档价格计。
7.本《价格表》中各部分的系数，凡遇多个同时出现时，应将系数相加后计算。
8.本《价格表》所列之价格，均系出厂价格。
9.凡工厂委托外单位加工、借用设备、外购器材等，应按工厂实际支付费用加上运杂费、管理费及法定利润、税金。
10.本《价格表》之价格仅适用于厂区作业，离厂区作业及出差施工价格另计。
11.本《价格表》适用于正常工作日的日班作业，若船方要求特急需逾时加班者，则应增收加班费。
12.船舶在工厂修理期间，其因修换而拆下的旧件、旧料，均归船厂所有。
服务项目一、船舶靠离码头系解缆：元/次（注：下列价格不包括拖轮费）二、码头费：以船长每米24小时一天计，不足一天按一天计算，每天每米：5元（注：特殊船型价格另计）三、消防值班：以一天24小时计，不足一天按一天计算，每天每人：85元。
四、消防巡回检查，以一天24小时计，不足一天按一天计算。
元/天五、接拆电缆、水管：1、电缆接拆一次：138元2、水管接拆一次：102元3、消防软管接拆一次：102元六、清除生活垃圾，船长100米以下40元/天船长100米以上70元/天七、临时放置消防器材：50元/只八、供淡水、供电：按当地实际情况计价。
《船舶修理报价》word版
4.2.3机械部分（1）柴油机主机(单作用十字头型)说明：a 缸径在两个规格之间，按大缸径计价；b 下列修理内容中未述及的修理和换新项目价格另计；c 须配置拆卸专用工具价格另计；d 测量、调整中心另计。
①气缸盖拆除有碍件，拆下气缸盖，清洁，检查，装复。
表4-3缸径（毫米）价格（每缸）（元）400 2730500 2890600 3060700 3230800 3390900 3560②活塞拉出活塞，清洁，检查后装复。
表4-4缸径（毫米）价格（每缸）（元）400 4470500 4800600 5130700 5380800 5620900 5870备注：a 上述价格不包括气缸盖拆装；b 更换活塞环备件、研磨活塞环间隙价格另计。
③缸套拉出缸套，清洁冷却水腔，涂漆，密封圈换新，装复后水压试验（油漆、密封圈船供）。
表4-5缸径（毫米）价格（每缸）（元）400 3230500 3470600 3720700 3970800 4220900 4470备注：a 上述价格不包括缸盖和活塞拆装；b 气缸盖凸痕研磨价格另计。
④主轴承、十字头轴承和曲柄销轴承轴承打开，清洁，检查，装复。
表4-6缸径（毫米）主轴承（每道）（元）十字头轴承（每缸）（元）曲柄销轴承（每道）（元）400 1240 1570 1200500 1410 1740 1320600 1570 1900 1490700 1740 2070 1650800 1900 2230 1820900 2070 2400 1980 备注：主轴承仅打开上盖检查，按上述价格50%计价。
⑤活塞杆填料箱拆卸，清洗，检查测量，换船供备件，装复。
表4-7缸径（毫米）价格（每缸）（元）400 1390500 1520600 1650700 1750800 1850900 1950⑥曲轴拐档表测量修理前后拐档差测量价格标准6缸机1240元8缸机1410元仅测量拐档差而打开曲轴箱道门290元/每缸（2）柴油机副机发电机组的柴油机气缸盖拆装，解体，清除积炭；进排气阀、安全阀、启动阀、试验阀拆检，清洁，研磨，压力校正；活塞抽出，解体，清洗，检查，测量，不良活塞环换新（船供）；主轴承拆检，间隙测量，调整；缸套就地清洁，测量；高压油泵、喷油器拆检，研磨，压力校正；柴油机装复后进行运转试验。
《国内民用船舶修理价格表》92黄本
《国内民用船舶修理价格表》使用说明1.本《价格表》系参照我中国船舶工业总公司系统各船厂的历史资料并结合修船产品实际情况和现行市场价格水平，经测算整理汇编成册，供我公司系统各单位使用。
2.本《价格表》仅适用于民用常规船舶的修理。
3.本《价格表》中已包括材料的项目,其材料费是按91年现行价格测算的，如遇材料市场价格有较大变动时，各厂按实际情况适当调整其差价部分。
4.本《价格表》中各分项说明中均已明确修换范围，其他附带工程及可能产生的零部件换新以及施工工艺所需的专用工具、模具、胎架、专用设备等费用另计。
5.凡单一性技术劳动,如柴油机的喷油器、高压油泵、调速器、冰机、空调等的修理价格可作适当上浮.6.本《价格表》所列的各档规格，凡在两档之间者均按高一档价格计。
7.本《价格表》中各部分的系数，凡遇多个同时出现时，应将系数相加后计算.8.本《价格表》所列之价格，均系出厂价格。
9.凡工厂委托外单位加工、借用设备、外购器材等，应按工厂实际支付费用加上运杂费、管理费及法定利润、税金。
10.本《价格表》之价格仅适用于厂区作业,离厂区作业及出差施工价格另计。
11.本《价格表》适用于正常工作日的日班作业，若船方要求特急需逾时加班者，则应增收加班费。
12.船舶在工厂修理期间,其因修换而拆下的旧件、旧料，均归船厂所有.服务项目一、船舶靠离码头系解缆：元/次（注：下列价格不包括拖轮费）二、码头费：以船长每米24小时一天计,不足一天按一天计算,每天每米：5元（注：特殊船型价格另计）三、消防值班:以一天24小时计，不足一天按一天计算，每天每人：85元.四、消防巡回检查，以一天24小时计，不足一天按一天计算。
元/天五、接拆电缆、水管：1、电缆接拆一次:138元2、水管接拆一次:102元3、消防软管接拆一次：102元六、清除生活垃圾，船长100米以下40元/天船长100米以上70元/天七、临时放置消防器材:50元/只八、供淡水、供电：按当地实际情况计价.九、测爆:元/次注:船舶进厂后局部测爆每次每处50元；厂区外测爆交通费另计.十、引水费:根据各厂实际情况计价。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
船舶修理价格表TARIFF FOR SHIP REPAIRS中国船舶工业总公司CHINA STATE SHIPBUILDING CORPORATIONGENERAL NOTES1. The rates quoted herein are in US dollar $.2. The rates are applicable to the work carried out during the normalworking hour, that is five working days a week, and sixteen hoursa day. Any works done outside these hours or on Saturdays andSundays, National Holidays and yard's holidays shall be charged with extra for overtime, ship on voyage repair will be priced extra.3. All prices quoted herein are for ship repairs carried out in thepremises of the shipyard, extra price should be added for such repairs carried out at the port berths, buoys, anchorages according to the actual work to be done.4. Any vessel during the repair period of repair in the yard, unlessagreed by the yard, the Customer shall not be permitted to employ any labor other than the yard to perform repairs.5. The yard shall not be responsible for the consequences of war,earthquake or causes beyond yard's control.6. All scrapped material except heavy parts of machinery, propellerand tailshafts shall be the yard's property.7. This tariff is applicable to the repair of freight carriers only, repairsof other types of ship are beyond of this tariff scope.8. This tariff becomes effective from January 1st, 1991, subject torevised price depending on the change in material cost etc. without notice.CONTENTS1.General Services page1.Wharfage 12.Mooring and unmooring 13.Shore electric power supply 14.Cooling water supply 15.Fresh water supply 16.Water to ballast tank 17.Fire precautions 28.Garbage disposal 2pressed air supply 210.Steam supply 211.Telephone service 212.Ventilation fan 213.Heating lamp for electric motor 214.Gas free inspection 215.Rental of crane 216.Drain pipes 317.Gangway for ship mooring 318.Shipyard pilotage 3 2.Docking Works1.Docking charges 42.Tugs charges 43.Tailshaft 54.Rudder 65.Underwater works 7(1)Sea chests 7(2)Sea valves 8(3)Zinc anodes 8(4)Bottom plugs 8 3.Hull Department1.Cleaning and painting 9(1)Marks repainting 9(2)Hull cleaning 9(3)Painting 9(4)Scraping and chipping 10(5)Gritblasting 10(6)Staging 102.Anchors and chain cables 11(1)Anchor chain cable 11(2)Chain blocker 113.Steel work 12(1)Renewal 12(2)Handrail fence 13(3)Hatch cover, watertight door, manhole cover 134.Tank work(1)Cleaning 13(2)Chipping and mud removal 14(3)Test 145.Derrick union 15 4.Machinery Works1.Diesel engine 162.Turbo charger 183.Heating exchanger 184.Aux. Boiler 195.Pipe 206.Valve 21 5.Electric Works1.Motor 222.Generator 22General Service1.WharfageLess than 5000 GRT 125 per day5001 to 20,000 GRT 0.025 per gross ton per dayOver 20,000 GRT 500 + (Gross ton – 20000) x 0.02 per day2.Mooring and unmooring (per time)Up to 5,000 GRT 8005,001 to 10,000 GRT 1,12010,001 to 20,000 GRT 1,56020,001 to 30,000 GRT 2,05030,001 to 40,000 GRT 2,60040,001 to 50,000 GRT 3,20050,001 to 60,000 GRT 3,900Over 60,000 GRT 4,700Note:(1)Above rates at normal working hours on shipyard’s premises for mooring andunmooring.(include Towage service)(2)Above rates including line handling.(3)In case of overtime, extra 30% shall be charged.(4)If owners change the towing plan, unless there is timelynotice to shipyard, extra 50% shall be charged for waiting.3.Shore electric powerConnection and disconnection of cable 100 per timeCurrent, per K.W.H. (AC) 0.204.Cooling water supply to food refrigeratorLine to connect and disconnect 40 per time per lineWater supply 40 per day per line5.Fresh water supplyLine to connect and disconnect 40 per time per lineFrom shore 1.00 per ton(Prices are separately charged from barge)6.Water to ballast tank (sea and river water)Line to connect and disconnect 40 per time per lineSupply of water 0.40 per ton7.Fire precautionsPut fire extinguishers 10 per day Fire line to connect and disconnect 40 per time per line Keep pressure 20 per day per line Fire watch, per man (24 hours) 120 per day 8.Galley garbage disposal30 per day pressed air supplyLine connection and disconnection 40 per time per line To supply 40 per day (8 Hours) 10.S team supplyLine connection and disconnection 200 per time per line To supply 20 per hour 11.T elephone serviceTelephone wire connect and disconnect 30 per time4 per set, per day(Toll calls to be extra)12.V entilation fan15 per set per day 13.H eating lamp for electric motrorInstallation 5 per set Maintenance 5 per set, per day 14.G as free inspectionTanker 80 per time Other vessel 40 per time 15.R ental of crane(1)Shore craneLess than 30 ton 90 per hour(2)Floating craneLess than 30 ton 90 per hour50 ton 150 per hourover 50 ton extra Note:(1)Any fraction of one hour shall be charged as one full hour.(2)Floating crane price excludes tuggage price.(3)At shipyard outside service, price shall be charged extra.16.C onnection of sewage water drain pipes and grooves20 per pc 17.S hip mooring gangway ladder on and off (per time)Less than 5000 gross ton 250 Less than 10000 gross ton 350 Less than 20000 gross ton 500 Over 20000 gross ton extra 18. Shipyard pilotage chargedUp to 20000 GRT 800 Up to 40000 GRT 1000 Up to 60000 GRT 1200I. Docking works1.(1) Floating docks extra 10% to be added.(2) Above rates excluded towage service and line handlers for docking and undocking. (3) Minimum charge will be calculated on the basis of 48 hours. Any fraction of one subsequent day shall be counted as one full day.(4) Any vessel having gross tonnage less than of 60% her deadweight, shall be charged with dockage calculated as if her gross tons were of 60% the deadweight.(5) When the vessel with cargo onboard is allowed to drydock weight of the cargo onboard shall be added to gross tonnage of the vessel. (6) Special vessel shall be charged extra.(7) Extra charges shall be paid when: remove and replace keel blocks for access to repair USD75 per each, side blocks for access to repair USD50 per each.(8) Loss incurred, if any, may be claimed for, compensation against abrupt cancellation after shipyard made all necessary preparation for the docking2. (1) A bove rates at normal working time, all overtime and national holidays, extra 30% shall be charged. (2) T owage services as required for other work shall be charged by 0.15/HP.hour.Above tug boat price are all net price.3. Tailshaft(1) Conventional service------draw of tailshaft, for examination, measure, and recording,rope guard to remove, propeller to disconnect and tailshaft to draw, including removal of one intermediate shaft, bearing and cooling water pipe, in shaft alley, stern gland to(1) A bove price includes necessary staging. (2) T he following items shall be charged extra: Shaft alignment adjustment.Filling with tallow in propeller bonnet and boss Renewal of water seal rubber ring Magnaflux test on tailshaft coneRemoval and replacement of miscellaneous fittings in engine room and shaft alley, such as handrails and cables, etc. Any repair and / or renewal.Tailshaft and / or propeller to workshop. (3) Above price diameter of tailshaft means diameter of the brass sleeves. (4) C ontrollable pitch propeller shaft to be considered separately. (5) D ue to tailshaft, intermediate shaft, main thrust shaft removal, necessary removal hull plate extra charge. (6) 40% of price of the above will be charged in case of disconnecting only propeller.(2) Remove rope guard and measure stern tube bearing wear-down and renewal with owner(1)In case 5 blades, 20% up; 6 blades, 30% up.(2)Above price staging shall be extra.4.Rudder(1) Check and record rudder pintle clearance in place(3) Rudder lift up, to disconnect steering gear, lift up rudder for checking clearance and(1)Simplex rudder, hanging rudder and AEG type to be charged with extra 20%(2)Ruder rod and rudder blade removal to be extra.(3)All spares to workshop repair charged with extra.5.Underwater work(1) Sea chest:Removal strainer, clean, one coat paint and close on completion.area per eachUp to 0.5 sqm 70Over 0.5 sqm 120Note:(1)Above price excluding any repair, renewal and staging.(2)Paint supply by owners.(2)Sea valveOpen up sea valves for survey, grind in, clean and paint,(owner supply) renew packing,Note:(1)Renewal of valve (with owner’s valve), 80% of above tariff.(2)Valve to workshop for repair, 150% of above tariff.(3)Any renewal and repair will be charged separately.(3) Zinc and hull anodes(1) Renewal with owner’s materialless than 10 kg 13 per pc10 ~ 25 kg 16 per pcover 25 kg 20 per pc(2) Renewal with yard’s material per pcsize 300 x 150 x 30mm 58 per pcstaging price to be charged extraNote:(1)Double tank and ballast tank zinc anode renewal (owner supply) add 30%above tariff.(2)Staging price to be extra.(4) Bottom plugsRemoval and refitting (including cement-washing) per pc 18(any repair and renewal and staging will be charged separately)III. Hull Department1 Cleaning and paintingNote:(1) Staging shall be extra.(2) Paints to be supplied by owner.(3) Above price will be only applicable to work carried out in dock.(2) Hull cleaning ( Per sq.m.)High pressure water washing (pressure over 200kg/sq.cm) 0.80 Washing down with fresh water 0.30 Removal of oily spots 4.00Note:(1) Under 300 sq.m, price shall be charged extra. (2) Staging shall be extra.(1) Staging shall be extra. (2) Paints supplied by owner.(3) If coatings of bitumen paint are required, extra shall be charged with addition of 20%, if coating SPC thickness 75 micron add 50% charge, over 75 micron shall be extra.(4) Scraping and Chipping (per sq.m.)Note:(1) Prices for surface area in dirty condition shall be charged extra.(2) Staging shall be extra.(3)Other tank work shall be charged extra.(5) Gritblasting (per sq.m.)Note:(1)Spotblasting (hull up to 300sq.m., hold up to 500sq.m. per hold) shall be chargedwith extra 50% of above price.(2)Excluding necessary staging and any other accessary work.(3)For double tank above price extra charged.(4)Surface area in dirty condition to be charged extra.(5)Mechanical scaling before Gritblasting, price shall extra.(6) Staging (actual length / per meter)Outside shell 4In cargo hold 5In engine room 6Note:(1)Under 30 M, additional 50% of above to be charged.(2)Prices for in-side, difficult area such as internal tank, hold, etc. to becharged extra 100%.(3)At the supperstructure, mast, etc. high position, to be charged extra.(4)Use hydraulic crane working 50USD per hour per set.2.Anchors, anchor cables (port and stb’d)(1)ranging anchors and cables, port abd stb’d sides, wash down chain cables with freshwater, light scraping and chipping, apply one coat with owner’s supplied paint an drestore. Unshackling, and reshackling, measure chain cables diameter and reversingmarking and close up on completion.(1)Range down and clean, measure and close up on completion excluding chainreversing, overhaul of shackles, marking, painting.(2)All paints and bitumen will be supplied by owner(3)Unshackling and reshackling per piece 20. reversing per piece 120.(2)Chain locker (port and stb’d) clean, apply one coat with owner’s supplied paint andbitumen.(1)All paints and bitumen will be supplied by owner.(2)Excluding chipping and other assistance work.(3)Cleaning out mud and garbage, remaining water and grating removal excluded.(4)Removal of mud 60/ton; over 10 tons, 50/ton.Remaining water 30/ton; over 10 tons, 25/ton.3.Steel work(1)RenewalFollowing costs shall be applied to renewal of welded construction plates such as side plates, main deck plate and bulkhead plate.Weight of steel per ton priceUp to 1 ton extraUp to 5 tons 2,803Up to 10 tons 2,689Up to 100 tons 2,565Up to 200 tons 2,395Up to 300 tons 2,265Up to 400 tons 2,135Over 400 tons 2,010 Note:(1)The rates for weights are charged on the continued-scope. Steel weights of theseparate position do not added up together.(2)Above price are applicable to steel plate of 10mm thickness and over 10mm; upto 10mm extra add 10%.(3)Less than 3mm will be charged extra.(4)Following plates renewal to be extra:Engine room and pump room 10% upD.B. tank, F.P. tank, and A.P.tank deep tank 20% upOil tank 30% upBottom plate and hold bottom plate 20% upKeel plate of forward or stern area 50% upBulbous bow 150% upFashion plate, stern plate 75% upHawse pipe 50% upCorrugated bulkhead plate, hinged, folding hatchcover, “PAM” type single-pullhatchcover, price by arrangement.(5)Following quality plate renewal price to be extra:Plate with single curvature 12% upPlate with double curvature 25% upHigh strength plate 20% upSpecial steel ExtraStraight frame 10% up(6)Above price exclude tank work oil shifting, tank cleaning, gas freeing andremoval of blocks, staging, shot blasting, water and jet cleaning other pressuretesting, X-ray examination and other accessary work.(7)Steel weight to be calculated from greatest length plus 2% of steel weight onallowance for wastage.(8)For off fair and refit, price shall be at 80% of its renewal price.(9)For patching instead of cropping, price at 85% of its renewal price.(10)Steel weight up to 8kg, USD 32 per pc.(11)For fair in place, price at 50% of its renewal price.(2) Handrails and fence (on deck)Handrail renewal (pipe 1 1/4” ~ 1 1/2”)16/M(round bar 3/4”)14/M renewal of stanchion 24/Mrectify in place 10/M(3) Cargo hold cover and watertight door, manhole cover:(1)Cargo hatch coverPacking renewal (owners supply packing) 8/MDerusting for packing groove 7/MNote: (1) Removal and refitting of hatchcover shall be extra.(2) Hose test shall be extra.(2)Watertight doorPacking renewal and derust, paint 70/pcWater test 8/pc(3)Manhole coverOpening and closing manhole cover 30/pcPacking renewal (including cover opening and closing) 60/pcNote: Renewal bolts and nuts to be extra.4. Tank work(1)tank cleaning(1)fresh water tankup to 100 cub.m./tank 2.05/cub.m.over 100 cub.m./tank 1.85/cub.m.Note:The above price will be based on tank capacity above 50 c.m., up to 50 c.m. tank capacity shall be extra,removal of mud and scale and ventilation shall be extra.(2)Sea water tankUp to 200 cub.m. /tank 2.20/cub.m.Over 200 cub.m. /tank 2.00/cub.m.Note:The above price will be based on tank capacity above 100 c.m., up to 100 c.m. tank capacity shall be extra,removal of mud and scale and ventilation shall be extra.(3)Oil tankUp to 100 c.m. /tank Diesel oil 7.50/c.m.Fuel oil 12.00/c.m.Over 100 c.m. /tank Diesel oil 6.50/c.m.Fuel oil 10.00/c.m.Note:(1)Above price will be based on tank capacity about 50 c.m., up to 50 c.m.tank capacity shall be extra.(2)Engine room double bottom tank, lub oil tank cleaning, price shall becharged as diesel oil tank.(3)Above price excludes opening and closing manhole cover, removing pipesand obstruction for access.(4)Steaming and solvent washing will be charged extra.(5)Provide ventilation fan equipment shall be extra.(6)Tank removal mud shall be extra.(7)If the tank clean for hotwork,price shall be extra.(4) Derusting and removal mud1.Painting and derust prices shall base on prices for cargo holds painting, to becharged at higher level, which are to be fixed according to the works contents.Wash cement (supplied by owner)Tank capacity 2.00 per cub.m per coat2.Removal mud etc.:Removal oil sludge 240 per tonMud 60 per tonMud over 100 tons 50 per tonSewage disposal 90 per tonRemains water 30 per tonRemains water over 10 tons 25 per ton(2)Tank testingSea water test 1 per cub.m.Fresh water tank 2 per cub.m.Note:(1)For tank capacity up to 50 cub.m., shall 50 cub.m charge.(2)Air test per USD1 per cub.m.(3)The above price exclude manhole cover removing, staging, cleaning outremainders of the tank and any repair work and pumping water out of tank aftertest .4.Derrick union(1)Derrick goose neckTo open up, draw pin, clean, adjust and reassemble, per pc.SWL 5 tons10 tons15 tons 110 120 145Note:access staging, renewal or repair, if any , to be extra.(2)Block1.Cargo block overhauling of topping, per pc.SWL 5 tons10 tons15 tons80 100 125Note:(1)Double sheaves block overhauling in place, the charge shall add 50%, threesheaves add 80% four sheaves add 100%.(2)Access staging, renewal or repair, of any, to be extra.(3)Bull type bearing block 20% up of above price.(4)Deck crane post sheaves and jib sheave block overhaul per unit5 tons 26010 tons 350(5)If removal to workshop overhauling shall be above 25% add price.(6)Cable removal shall be extra.(3)Derrick boom and deck crane load test by weight per unit(1)Derrick boom test proof weight5 tons 14510 tons 19515 tons 245(2)Heavy derrick load test by weight30 tons 115550 tons 216580 tons 4300(3)Deck crane test proof weight5 tons 24010 tons 34015 tons 440IV. Machinery Department1.Diesel main engine (single acting crosshead type)(1)Open up cylinder cover, remove other accessory partsCylinder bore (mm) per unit400 360500 400600 440700 480800 520900 5601000 600(2)Draw out piston and clean for survey, gauging cylinder liner and close upon completionCylinder bore (mm) per unit400 600500 675600 750700 825800 900900 9751000 1050(3)Draw out cylinder liner, clean and paint in way of cooling water space,refit in position with new rubber rings, hydrotest liner on completion.( owners supply paint and rubber rings)Cylinder bore (mm) per unit400 430500 480600 540700 590800 650900 7001000 750(4)Draw and examination of main, cross hand and crank bearing, clean after refitting.(per pair)Note:(1)For any size between two specified sizes, the rate of higher size shall be applied.(2)Open up main bearing at top half, 50% charge.(3)Bearings adjusting of clearance shall 200% charge.(4)Gauging and adjusting center shall be extra.(5)The above prices are not applicable to medium speed engine, shall be extra.(6)Due to the erosion of engine’s parts for making special tools for removing and refittingparts, the price shall be charged extra.(7)Any repair work shall be extra.(5)Exhaust ValveRemove exhaust valve to workshop, open up, clean, grind in, hydrotest and return onboard.Cylinder bore (mm) per unit cyl400--600 400700--800 420900--1000 470(6)Stuffing BoxRemove piston rod stuffing box, renew spare metallic packing rings (owner supply) dress, adjust clearance and refit same.Cylinder bore (mm) per unit cyl400--600 250700--800 265900--1000 280(7)Crankshaft deflectionTo check crankshaft deflection before and after repair and submit copies of reading.For 6 cylinder engine 1708 cylinder engine 190r2.Turbo chargerOpen cover, remove rotor, clean, overhaul, renew owner supply spare parts, close and test.(exclude remove air inlet case and exhaust case, rotor ballance and silencer chemical cleaning)Type per unitVTR200 420VTR250 530VTR320 730VTR500 1200VTR630 1440VTR750 20903.Heat exchangers(1)Aux. condenser, L.O. cooler and F.W. cooler.Open up covers, clean sea water side, cover inside coat with paint and close,test, per setexchangers surface areaUp to 20 sq.m. 450Up to 50 sq.m. 540Up to 80 sq.m. 630Up to 150 sq.m. 720(2)L.O. cooler and F.W. cooler inside and chemical cleaning in workshop. Open upcovers, clean inside with chemical, test and close, per set.exchangers surface areaUp to 20 sq.m. 810Up to 50 sq.m. 970Up to 80 sq.m. 1134Up to 150 sq.m. 1296Note:(1)Zinc plate and other accessary parts renewal shall be extra.(2)Above price excluding removals of obstruction access.(3)If staging necessary, price to be extra.4.Auxiliary Boiler (Boiler output 1.5ton/hour vertical fire tube type)(1) Clean boiler water and fire surface 2800 per boilerNote:(1)Chemical clean shall be extra.(2)Superheater or draw superheater coil clean shall be extra.(3)Opening of doors and hand hole shall be extra.(2) Boiler mountings repair:Boiler mountings to open up, check for survey in place, grind in, and close with new packing.Valve diameter (mm) 1” 25mm2” 50mm3” 75mm4” 100mm5” 125mm Globe valve405275100120Cock7080Note:(1)Overhaul of superheater valve shall be extra.(2)Any repair and renew shall be extra.(3)Remove valve to workshop repair shall be extra.(3)S afety valve:Safety valve to open up, check for survey in place, grind in, and close with new packing, refit same and test.Single valve 270 per pcDouble valve 390 per pc Note:Removal to workshop repair shall be extra.(4)T estSupply fresh water for testing,each test 2505.Pipe workPipe renewal including bolt, nut and gasket, excluding flanges and bends.Note:(1)For pipe length under one meter, price shall be applied as one meter, for pipelength over one meter , calculation will be made according actual length, forany size between two specified sizes, the rate of higher size shall be applied.(2)Above prices are not applicable to S-shaped pipe, tank heating coil and oiltank pipes.(3)Above prices excluding staging, pressure test, removal of obstruction foraccess, painting and insulation, cleaning tank and gas free.(4)In the following case, extra are charged:Pipe in engine room, pump room and cargo hold add 20%.Double tank pipe and lavatory pipe add 35%.(5)Galvanized pipe add 25% and acid treated pipe add 15%.(6)High pressure pipe and alloy steel pipe shall be charged with extra.(7)Removal and refitting of pipe (excluding test) charge above price; on deckadd 30%, engine room add 40%, double tank and pump room and cargo oiltank pipe add 50%.(8)Newly replaced flange 3.5 per inch diameter pipe.6.Valve repairTo open up in place, clean, overhaul, grind in, renew packing and reassemble.Note:(1)When valve is sent to workshop for repair and test, price shall be chargedextra by 50%.(2)Any renewal and staging, paint, insulation access work not included.(3)For the valve (owner supply) renewal, price based on above globe valve priceas follows:(exclude pipe system refit)deck valve 70%engine room valve 80%pump room valve 100%(4)For valve in tank, cofferdam, pump room, above price shall be increased by30%, engine room 20%, pipe room 35%.(5)Valve working pressure over 7kg/sq.cm., price extra.V. Electrical department1.MotorRemoved to workshop, open up, clean, varnish, bake, close up and test on completion.Power (KW)13.77.51015203040506075100 AC motor1172102903134225476547027658449601240DC motor13524033636048562975280788097011041426Note:(1)Staging and attached works excluded.(2)Same noumenon transverter motor add 50%, multi-speed motor add 50%,fan motor add 25%.(3)Bearing renewal shall be extra.2.Generators(AC)A.C. alternators rotor drawing out, remove to workshop, measure megger, varnish, bake, polish communicator or rings, close up and test on completionPower (KW)501002003004005006008001000 AC alternators105514641920222225242826302434563960Note:(1)For D.C. generators, 10% shall be added to above prices.(2)Bearing renewal shall be extra.(3)Staging and attached works excluded.。