注塑常用术语英文表达
注塑专业中英文术语
Injection Machine Parameter1，注塑机规格参数 Injection Machine Specification①锁紧类型 clamp typea．油缸— hydraulic b．肘杆式— toggle②垂直注塑机导柱间距— tie bar vertical clearance③水平注塑机导柱间距— tie bar horizontal clearance④台板尺寸— platen dim.⑤最小 / 最大模厚— mold height Min./ Max., Min. / Max. mold thickness⑥最小 / 最大注塑机开档— open day light Min. / Max.⑦锁紧行程— clamp stroke ⑧锁紧力— clamping force⑨顶出行程— ejector stroke ⑩顶出力— ejector force2，试模工艺参数 Molding Process Parameter, machine setting①时间 Timer（TM）, seca, 注塑（充填）时间— filling time, injection timeb, 冷却时间— cooling time c, 补缩时间— packing timed, 保压时间— holding time e, 成型周期— cycle time②速率、速度 Velocity, %、speed, in/seca, 注塑（充填）速度— injection speedb, 保压速率— hold pressure velocityc, 螺杆转速— screw rotation speed③压力 Pressure（Prs.）, psia, 注塑压力— injection pressure b, 保压压力— hold pressurec, 回压（背压）— back pressure④温度 Temperature（Temp.）, °Fa, 注塑机喷嘴温度— nozzle temp.b, 料筒前段、中段、后段温度— barrel front、middle、rear temp.c, 模温— mould temp. d, 料温— purged resin melt temp.e, 空射料温— air shot melt temp.产品几何 Geometry1．点— point 2．线（边）— line, edge3．面 faceA 侧面— sideB 表面— surfaceC 外观面— appearance surface4．壁厚— wall thickness, stock thickness5．加强筋（骨位）— rib 6．孔— hole7．细长的槽— slot 8．柱位— boss9．角—cornerA 圆角— filletB 倒角— chamferC 尖角— sharp corner10．斜度— angle, taper 11. 凹槽—recess , groove一．分模信息 Splitting1．分型线— parting line (P/L), splitting line2．主分模方向— main direction, line of draw3．浇口设定— gating二．产品标识 Part Identification1．产品名称— part name (P/N)2．产品编号+版本号— part number + revision (Rev.)3．型腔号— cavity number 4．材料标记— material symbol 5．模具编号— mold number (no.) 6．日期印—date code7．循环印— cycling code 8．公司标志—company logo 三．技术要求 Specification (Special Requirement)1．项目启动表 Kick-off sheet5）项目启动日期— kick off date, start date6）项目完成日期— due date, lead time7）内模件用钢— tool steel8）型腔数量— number of cavities9）数据文件编号— data file no.10）注塑材料— resin, plastic, raw material11）收缩率— shrink, shrinkage, shrink factor12）注塑机吨位— molding machine size, injection machine size13）成型周期— cycle time14）型腔光洁度— cavity polish15）型芯光洁度— core polish16）皮纹（晒纹）— texture, grain17）拔模斜度— draft angle, removal taper18）注塑件颜色及光泽— molded color & gloss19）模具加工地— manufacturing facility20）热流道供应商— manifold manufacturer, manifold supplier21）浇口位置— gate location / position22）浇口类型— gate type23）产品标识— stamp information, part identification24）特殊要求— special instructions2．产品质量及外观要求 Part Quality & Appearance Requirement1）尺寸及公差 Dimension & Tolerance①重要尺寸— critical dimension, important dim., key dim.②理论尺寸—nominal dimension ③实际尺寸— actual dimension⑤公差带—tolerance range ⑥尺寸超差— dimension deviation⑧拒绝（不合格）— reject, refuse, obsolete, NG⑨让步接受— concession, special admit2）产品缺陷（常见的）Defects (normal)①缩水— sink mark, shrinkage ②飞边，毛边— flash, burr③段差— mismatch discrepancy ④银丝纹，蛇纹—snake marks, streak⑤弯曲，变形— warpage, distortion⑥打不饱（缺料）— short shot ⑦熔接线— weld line⑧多胶— unwanted plastic ⑨拉伤—damage3．产品外观 Part Appearance①产品颜色— part color ②产品光泽— gloss③皮纹粒度— grain4．常用词汇、词组及短语 Normal Word, Short Sentence1）单边— per side 2）双边— both sides3）加入，添加— add, incorporate 4）去除，取消— remove, cancel5）满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet6）要求，需要— require, need, demand7）确认—be approved, agreed by …8）允许— permit, allow 9）在…范围之内— within10）不可以，不允许，禁止— free from, prevent, avoid11）除非有另指—… unless otherwise specified12）或少于—…or less13）自动化运作— automatic operation14）未注尺寸（详细形状）见三维造型Non dimensioned contour(detailed shape) see 3D model.15）分型线上的飞边（披缝）或段差应小于…Burrs or discrepancy on the P/L shall be … or less.注塑过程专业术语以及分析1, 热注射成型 thermoplastic injection molding2. 控制面板 control plat 对设备参数控制的简易操作平台3 显示器 pro-face 显示设备必要信息的屏幕4 安全门 safe door 防止事故发生,增大安全系数的保护装置门5 注射座 Injection blend 注射成型机组成部件,支撑并协助注射的金属平台6 螺杆 screw 起旋转计量作用的螺纹状部件.是成型机的核心机械件7 料膛 fabbrel 树脂预塑的炮膛状部件,和螺杆配合俎件质量要求较高8 加热圈 heater 围绕在料膛周围,起迅速并均匀加热作用的片状加热器9 喷嘴 nozzle 连接注射成型机料筒与模具浇口套接触的像针头状的组件10 定模板 plam 可固定模具在成型机上的铁板,是成型机的一部分11 动模板 moving plam成型机曲臂连接板,使模具固定在成型机上做开合模运动的动模板12 成型机顶杆 ejector pin 连接到模具上控制模具顶杆顶出或回退作用的连接杆13 手动操作 man 只能手动单一步骤状态操作14 半自动操作 sengle man 可半自动状态操作15 全自动操作 auto 根据设置的程序在全自动状态动作16 料膛清洗 purge 一般用PE料做**动作来清除或淡化料膛内物料或颜色17 上料机 loader 在料杯树脂不足在传感器监控下吸取储备树脂的成型辅助设备18 温调机，控制模具温度,保持在设定温度以内的温度控制设备19 参数监控画面，对设备具体参数设定的画面,一般配有图表20 生产管理画面 product menut 在全自动生产状态下对产品质量和数量控制的页面21 模板控制画面 plam control 模板动作状态控制页面22 顶出控制画面 ejector control 顶出动作状态控制画面23 加热管理画面 heat control 材料加热控制画面24 注射速度画面 speed control 注射过程中对速度控制的画面25 注射压力画面 fulling pressure control 注射过程中注射压力控制画面26 保压控制画面 packing pressure control注射后保持设定压力提高制品质量的控制画面27 计量控制画面 excit control 计量尺寸和相关参数控制画面28 报警显示画面 alarm view 设备动作异常或监控报警预览29 最大高度 maximum daylight 成型机模板打开的最大尺寸30 最小高度minimum daylight 能满足成型机性能的最小模具厚度31 锁模力 clamping force成型过程中为保证动，定模相互紧密配合而需施加的在模具上的力32 锁模系统 clamping system 模板控制系统,注塑机上系统的一部分33 控制系统 control system 计算机通过检测、处理信息并重新输入计算机进行控制相关参数34抽芯距 core-pulling distance 将侧型心抽至不防碍制品脱落的滑块滑动的距离35 抽芯力 core-pulling force 从模内的成型塑件中，抽**侧型心所需要的力36 生产周期 Cycle time 生产每个制品的时间或是单位时间内生产制品的个数37 液压系统 hydraulic system 液压动力注射机上的压力系统38 短射 short shot 由于一次注射压力不足或速度偏低引起的浇不足现象39 ** jetting 材料水份超标,结构不良引起的表面气泡等不良现象40 白化，制品破坏前变形引起的颜色差异41 缩痕 shrinkage 热熔体在收缩情况下表面会形成凸凹状现象的统称42 收缩差异 asymmetric shrinkage 制品厚度不均匀或分子排列不同引起的不均匀收缩43 熔接线 lines 两股或多股熔体结合位置形成的线状痕迹44 亮线 color change 一种有明亮痕迹的注塑成型缺陷，一般为线状少为带状45 冷熔接 Cold welding 低温区域的熔接，多见于冲填结束，不同塑料熔前交汇造成46 困气 air traps 又称包气,熔体流动将气体堵住或包住不能及时排出47 烧伤 burn 填充时模具内部气体不能迅速排出产生压缩高温,导致制品局部变色48黑斑 black specks 注射成型过程中因高温或树脂分解等原因引起的黑色不良现象49 料纹 black streads树脂在模具腔内流动时由于层流因素引起的外观不良现象51 烧焦 burn marks 因高温引起的成型缺陷的一种52 色差 discoloration制品本身颜色有其他杂质颜色混入形成的不良现象53 脆化 brittleness 成型缺陷（因树脂性质发生变化引起的脆化或者破裂）54 蠕变 Creep高聚物在恒定温度和应力下，长度随时间延长而逐步深长的现象55 位移 Displacement熔体内部压力差引起高压部份向低压部分推移现象,可产生层次感56 分层表面剥离 delamination同一树脂或不同树脂发生层流后产生的现象57 三角洲效应 delta effect局部温度差58 方向收缩 diectional shrinkage由大分子链排列引起的具有方向特性的收缩59 尺寸变化 dimensional variation生产出的制品在不同的环境下都会产生尺寸的变化60 尺寸稳定性 dimensional stability制品尺寸的稳定性和一致性61 密度 Density 单位体积的质量62 翘曲 warpage 有多种原因引起的变形现象,如收缩翘曲,配向翘曲等63 变形 distortion 产品在内应力或外力的作用下产生的尺寸变化以及形状变化64 迟滞 hesitation 熔体的某一部份发生停止流动或极缓慢流动的现象65 垂直于流动方向的收缩 cross-flow shrinkage 发生在垂直于熔体流动方向上的收缩66 热变形温度 deflection temperature热力的作用下，塑料可以发生变形的温度67 脱模 demolding 保压后制品在模具内部成型完毕脱离模具的现象68 脱模斜度 draft 方便成型制品脱离模具而设计的角度69 脱模困难 ejection difficulties 成型制品不容易脱离模具的现象70 内应力 internal stress 残留在制品内部因各种原因产生的应力71 长链高分子 long chain macromolecules 很多小分子连接而成的具有较大质量的长分子连72 凝固层比例 frozen layer fraction 熔体在模具内冷却状态之一的数学表示方法73 取出 removal 成型后制品拿出的过程74 粗加工 rough machining 毛坯加工或留有大量余量的待加工品75 伺服马达 servomotor 配合CPU工作的马达76 工序 workstage 完成一个组件或产品经过的步骤77 塑料件 plastic parts 以塑料为原料生产的制品78 注射模 injection mould 通过注射方式成型的模具79 斜销 angle pin / finger cam 倾斜于分型面、随模具的开闭产生相对运动的圆柱零件80 斜滑块 angled-lift / splits 斜向镶块或滑动的镶块81 悬臂搭扣连接 cantilever snap joints组合方式之一82 模套 chase / bolster / frame 使镶件或拼块定位并紧固在一起的框套形结构零件83 型芯 Core 成型模具内表面突起的组件84 支架 ejector housing / mould base leg 使动模能固定在压机或注塑机上的L型垫块85 推块 ejector pad 在腔内起部分成型作用，并在开模时把塑件从型腔内推出的零件86 推杆 ejector pin 用于推出塑件或浇注系统凝料的杆件87 推板 ejector plate 支撑推出和复位零件，直接传递机床推出力的板件88 复位杆 push-pack pin 借助模具的闭合动作，强制推出机构复位的杆件89 浇口尺寸 Gate dimensions(sizes) 浇口的相关尺寸90 直接浇口 direct gate ; sprue gate 熔融塑料经主流道直接进入型腔的进料方式91 盘式浇口 disk gate 沿塑料件内圆周扩展进料的浇口92 侧浇口 edge gate 设置在模具的分型处从塑件的内或外侧进料的方式93 扇形浇口 fan gate 从分流道道型腔方向的宽度逐渐增加的呈扇型的浇口94 浇口镶块 gating insert 浇口以镶块的形式存在95 圆柱头推杆 ejector pin with cylindrical head 头部形状是圆柱型形推杆96 扁顶杆 flat ejector pin 工作截面为矩形的顶杆97 连接推杆 ejector tie rod 连接推件板与推杆固定板，传递推力的杆件98 导套 guide bush 与导柱相配合，用于初步确定模具99 导柱 guide pillar 起导向作用的部件，一般为圆柱体100 浇口 gate 连接分流道合型腔的进料通道101 浇口长度 gate length 浇口的长度102 浇口位置 Gate location 树脂流入模腔的点相对整体模腔的位置103 嵌件 insert 成型中埋入或随后压入塑件中的金属或其他材料的部件104 楔紧块 heel lock 带有楔角,用于合模时楔紧滑块的零件105 凹模 cavity plate 成型塑件外表面的凹壮零件(包括零件的内腔和实体两部分)106 凹模拼块 cavity splits 母模中的镶件拼块107 定模座板 fixed clamp plate 使定模固定在注塑机的固定工作台面上的板件108 顶出系统设计 ejection system design顶出制品机构的类型109 顶出时间ejection time 制品脱离模具可安全取出的时间110 推板导套 ejector bushing 与导柱滑配合，用于推出机构导向的圆柱形零件成型工艺 Molding technique procedureA 成型工艺 Section 1 molding technique.1.成型工艺参数类型 Sorts of molding parameter.(1). 注塑参数 Injection parameter.a.注射量 Injection rate.b.计量行程Screw back positionc.余料量Cushiond.防诞量Sucking back ratee.螺杆转速Screw speedf.塑化量Plastic0 rateg.预塑背压Screw backpressureh.注射压力和保压压力Injection pressure and holding pressurei.注射速度Injection speed(2)合模参数Clamping parametera.合模力Clamping forceb.合模速度Clamping speedc.合模行程.Clamping stroked.开模力Opening forcee.开模速度Opening speedf.开模行程Opening positiong.顶出压力Ejector advance pressure h.顶出速度Ejector advance speedi.顶出行程Ejector advance position2.温控参数Temperature parametera.烘料温度Dry resin material temperatureb.料向与喷嘴温度Cylinder temperature and nozzle temperaturec.模具温度Mold temperatured.油温Oil temperature3.成型周期Molding cyclea.循环周期Cycle timeb.冷却时间Cool timec.注射时间Injection timed.保压时间Holding pressure timee.塑化时间Plant timef.顶出及停留时间Knocking out and delay timeg.低压保护时间Mold protect time成型工艺参数的设定须根据产品的不同设置.Molding technique parameter setting differs depending on type of product成型条件设定 Molding parameter Setting按成型步骤:可分为开锁模,加热,**,顶出四个过程.Molding steps: mold opening/closing, heating injection and knocking out.开锁模条件:Mold opening parameter: 快速段中速度High-speed mid-speed低压高压速度Low pressure high pressure speed锁模条件设定:Mold closing parameter setting1锁模一般分: 快速→中速→低压→高压Mold closing: high-speed →low-speed →low pressure→ high pressure。
（精编）模具注塑术语中英文对照
（精编）模具注塑术语中英文对照(精编)模具注塑术语中英文对照根据国家标准，以下为部分塑料模具成形术语的标准翻译。
动模MovableMouldMovingHalf定模座板FixedClampPlateTopClampingPlateTopPlate动模座板MovingClampPlateBottomClampingPlateBottomPlate上模座板UpperClampingPlate下模座板LowerClampingPlate凹模固定板Cavity-retainerPlate 型芯固定板MouldCore-retainerPlate凸模固定板Punch-retainerPlate模套DieBodyDieSleeveDieBlank支承板BackingPlateSupportPlate垫块SpacerParallel支架EjectorHousingMouldBaseLeg模头DieHead模具分类8InjectionMold注塑模PlasticRubberMould塑胶模RubberMolding橡胶成形HotChamberDieCasting热室压铸SandMoldCasting砂模铸造ExtrusionMold挤出模Multi-CavityMold多模穴模具PalletizingDie叠层模PlasterMold石膏模ThreePlatesMold三板模PlainDie简易模PierceDie冲孔模FormingDie成型模ProgressiveDie连续模GangDies复合模ShearingDie剪边模CavityDie型腔模RivetingDie铆合模CompressionMolding压缩成型FlashMold溢流式模具ExtrusionMold挤压式模具SplitMold分割式模具MouldCavity型腔母模MoldCore模芯公模LargeDieMold大型模具PreciseDieMold 精密模具ComplexDieMold复杂模具FoamingMould发泡模具MetalDie金属模具PlasticMold塑料模具ToolStampingDiePunchDie冲压模具ExtrusionDie挤压模具GraphiteDie石墨模具流道浇口部分RunnerSystem浇道系统SprueColdMaterialTrap浇道冷料井SpruePuller拉杆RunnerDesign流道设计MainRunner主流道SecondaryRunner 次流道MouldGateDesign浇口设计SubmarineGate潜伏浇口TunnelGate隧道式浇口PinpointGate点浇口FanGate扇形浇口SideGate侧浇口EdgeGate侧缘浇口TabGate 搭接浇口FilmGate薄膜浇口FlashGate闸门浇口SlitGate缝隙浇口DishGate盘形浇口DiaphragmGate隔膜浇口RingGate环形浇口Runnerless无浇道Sprueless无射料管方式LongNozzle延长喷嘴方式Sprue浇口，溶渣Insulated/HotRunner热浇道RunnerPlat 浇道模块ValveGate阀门浇口SlagWell冷料井ColdSlag冷料渣SprueGate射料浇口Nozzle 射嘴SprueLockPin料头钩销（拉料杆）注塑缺陷Flash飞边Warpage翘曲AirTrap积风Blush发赤FlowLine流痕Splay银纹ShortShot 短射SinkMark缩痕Streak条纹Void缩孔WeldLine熔接线GasMark烧焦ColdSlug冷斑Delamination起皮Burr毛刺FlawScratch刮伤Gloss光泽Glazing光滑SurfaceCheck表面裂痕Hesitation迟滞注塑工艺MoldingConditions成型条件Drying烘干BarrelTemperature 料筒温度MeltTemperature熔化温度MoldTemperature模具温度InjectionPressure注塑压力BackPressure背压InjectionSpeed注塑速度ScrewSpeed螺杆转速TensileStrength抗拉强度T ensileElongation延伸率FlexuralModulus弯曲模FlexuralStrength抗弯强度Shrinkage收缩率RegrindUsage次料使用Moulding模塑机械设备Lathe车床Planer刨床Miller/MillingMachine铣床Grinder磨床Driller钻床LinearCutting线切割ElectricalSparkle电火花Welder电焊机PunchingMachine冲床Robot机械手CommonEquipment 常用设备EDMElectronDischargeMachining放电加工3DCoordinateMeasurement三次元量床BoringMachine搪孔机ContouringMachine轮廓锯床CopyGrindingMachine仿形磨床CylindricalGrindingMachine外圆磨床DieSpottingMachine合模机EngravingMachine 雕刻机EngravingE.D.M雕模放置加工机FormGrindingMachine成形磨床GraphiteMachine石墨加工机HorizontalBoringMachine卧式搪孔机HorizontalMachineCenter卧式加工制造中心InternalCylindricalMachine内圆磨床模具零件TopPlate上托板（顶板）T opBlock上垫脚PunchSet上模座PunchPad上垫板PunchHolder上夹板StripperPad脱料背板UpStripper上脱料板MaleDie公模（凸模）FeatureDie公母模FemaleDie母模（凹模）UpperMoldPlate上模板LowerMoldPlate 下模板DiePad下垫板DieHolder下夹板DieSet下模座BottomBlock下垫脚BottomPlate下托板（底板）StrippingPlate内外打（脱料板）OuterStripper外脱料板InnerStripper内脱料板LowerStripper下脱料板InnerGuidingPost 内导柱InnerHexagonScrew内六角螺钉DowelPin固定销MouldCoilSpring模具弹簧LifterPin 顶料销IsoheightSleeve等高套筒Pin销LifterGuidePin浮升导料销GuidePin导正销WireSpring圆线弹簧OuterGuidingPost外导柱StopScrew止付螺丝LocatedPin定位销OuterBush外导套Punch冲头Insert入块（嵌入件）DeburringPunch压毛边冲子GroovePunch压线冲子StampedPunch字模冲子RoundPunch圆冲子SpecialShapePunch 异形冲子BendingBlock折刀Roller滚轴BafflePlate挡块LocatedBlock定位块SupportingBlockforLocation定位支承块AirCushionPlate气垫板Air-CushionEject-rod 气垫顶杆TrimmingPunch切边冲子StiffeningRibPunchStinger加强筋冲子RibbonPunch压筋冲子Reel-stretchPunch卷圆压平冲子GuidePlate定位板SlidingBlock滑块SlidingDowelBlock滑块固定块ActivePlate活动板LowerSlidingPlate 下滑块板UpperHolderBlock上压块UpperMidPlate上中间板SpringBox弹簧箱Spring-BoxEject-rod弹簧箱顶杆Spring-BoxEjec模具技术用语各种常用模具成形方式AccurateDieCasting精密压铸PowderForming粉末成形CalendaringMolding压延成形PowderMetalForging粉末锻造ColdChamberDieCasting冷式压铸PrecisionForging 精密锻造ColdForging冷锻PressForgingstampforging冲锻CompactingMolding粉末压出成形RockingDieForging摇动锻造CompoundMolding复合成形RotaryForging回转锻造CompressionMolding压缩成形RotationalMolding离心成形DipMold浸渍成形RubberMolding橡胶成形EncapsulationMolding注入成形SandMoldCasting砂模铸造ExtrusionMolding挤出成形ShellCasting壳模铸造FoamForming 发泡成形SinterForging烧结锻造ForgingRoll轧锻SixSidesForging 六面锻造GravityCasting重力铸造SlushMolding凝塑成形HollowBlowMolding中空（吹出）成形SqueezeCasting高压铸造HotChamberDieCasting热室压铸Swaging挤锻HotForging 热锻TransferMolding转送成形InjectionMolding射出成形WarmForging温锻InvestmentCasting精密铸造MatchedDieMethod对模成形法LaminatingMethod被覆淋膜成形LowPressureCasting低压铸造LostWaxCasting脱蜡铸造MatchedMouldThermalForming对模热成形模CloseMold合模Demould脱模脱模剂MouldUnloading开模ToolChangeRetoolingDieChanging换模MouldClamping锁模各式模具分类用语BismuthMold铋铸模LandedPlungerMold有肩柱塞式模具BurnishingDie挤光模LandedPositiveMold有肩全压式模具ButtonDie镶入式圆形凹模LoadingShoeMold料套式模具Center-GatedMold中心浇口式模具LooseDetailMold活零件模具ChillMold冷硬用铸模LooseMold活动式模具ColdHobbing冷挤压制模法LouveringDie百叶窗冲切模CompositeDies复合模具ManifoldDie分歧管模具CounterPunch反凸模ModularMold组合模具DoubleStackMold双层模具Multi-CavityMold多模穴模具ElectroformedMold电铸成形模Multi-GateMold复式浇口模具ExpanderDie扩径模OffsetColdBendingDie双折冷弯模具ExtrusionDie挤出模PalletizingDie叠层模FamilyMold反套制品模具PlasterMold石膏模BlankThroughDies漏件式落料模PorousMold通气性模具DuplicatedCavityPlate复板模PositiveMold全压式模具FantailDie扇尾形模具PressureDie压紧模FishtailDie鱼尾形模具ProfileDie轮廓模FlashMold溢料式模具ProgressiveDie顺序模GypsumMold石膏铸模PortableMold手提式模具Hot-RunnerMold热流道模具PrototypeMold雏形试验模具原型模具IngotMold钢锭模PunchingDie落料模LancingDie切口模切缝模Raising（Embossing）压花起伏成形Re-entrantMold倒角式模具SectionalDie拼合模RunlessInjectionMold无流道冷料模具SectionalDie对合模具SegmentMold组合模Semi-PositiveMold半全压式模具Shaper 定型模套SingleCavityMold单腔模具SolidForgingDie整体锻模SplitForgingDie拼合锻模SplitMold双并式模具SpruelessMold无注道残料模具SqueezingDie挤压模StretchFormDie拉伸成形模SweepingMold 平刮铸模SwingDie振动模具ThreePlatesMold三片式模具TrimmingDie切边模UnitMold单元式模具UniversalMold 通用模具UnscrewingMold退扣式模具YokeTypeDie轭型模t-Plate弹簧箱顶板BushingBlockLinerBushing衬套CoverPlate盖板GuidePad导料块模具厂常用之标准零配件AirVentValve通气阀AnchorPin锚梢AngularPin角梢Baffle调节阻板AngularPin倾斜梢BafflePlate折流档板BallButton球塞套BallPlunger定位球塞BallSlider球塞滑块BinderPlate压板BlankHolder防皱压板BlankingDie落料冲头Bolster上下模板Bottomboard浇注底板Bolster垫板BottomPlate下固定板Bracket托架BumperBlock 缓冲块Buster堵口CastingLadle浇注包Castinglug铸耳Cavity模穴（模仁）CavityRetainerPlate模穴托板CenterPin中心梢ClampingBlock 锁定块CoilSpring螺旋弹簧ColdPunchedNut冷冲螺母CoolingSpiral螺旋冷却栓Core心型CorePin心型梢Cotter开口梢Cross十字接头CushionPin缓冲梢DiaphragmGate盘形浇口DieApproach模头料道DieBed型底DieBlock块形模体DieBody铸模座DieBush合模衬套DieButton冲模母模DieClamper夹模器DieFastener模具固定用零DieHolder母模固定板DieLip模唇DiePlate冲模板DieSet冲压模座DirectGate直接浇口DogChuck爪牙夹头Dowel定位梢DowelHole导套孔DowelPin合模梢Dozzle辅助浇口DowelPin定位梢Draft拔模锥度DrawBead张力调整杆DriveBearing传动轴承EjectionPad顶出衬垫Ejector脱模器EjectorGuidePin顶出导梢EjectorLeaderBush顶出导梢衬套EjectorPad顶出垫EjectorPin 顶出梢EjectorPlate顶出板EjectorRod顶出杆EjectorSleeve顶出衬套EjectorValve顶出阀EyeBolt环首螺栓FillingCore填充型芯椿入蕊FilmGate薄膜形浇口FingerPin指形梢FinishMachinedPlate 角形模板FinishMachinedRoundPlate圆形模板FixedBolsterPlate固定侧模板FlangedPin带凸缘针FlashGate毛边形浇口Flask上箱FloatingPunch浮动冲头Gate浇口GateLand浇口面Gib凹形拉紧楔GooseNeck鹅颈管GuideBushing引导衬套GuidePin导梢GuidePost 引导柱GuidePlate导板GuideRail导轨HeadPunch顶头冲孔HeadlessPunch直柄冲头HeavilyT aperedSolid整体模蕊盒HoseNippler管接头ImpactDamper缓冲器InjectionRam压射柱InlayBush嵌入衬套InnerPlunger内柱塞InnerPunch内冲头Insert 嵌件InsertPin嵌件梢KingPin转向梢KingPinBush主梢衬套KnockoutBar脱模杵Land 合模平坦面LandArea合模面LeaderBush导梢衬套LiftingPin起模顶针起模杆Lining内衬LocatingCenterPunch定位中心冲头LocatingPilotPin定位导梢LocatingRing定位环LockBlock压块LockingBlock定位块LockingPlate定位板LooseBush活动衬套MakingDie打印冲子ManifoldBlock歧管档块MasterPlate靠模样板MatchPlate分型板MoldBase塑胶模座MoldClamp铸模紧固夹MoldPlaten模用板MovingBolster换模保持装置MovingBolsterPlate可动侧模板OnePieceCasting整体铸件ParallelBlock平行垫块PartingLine 分模线PartingLockSet合模定位器PassGuide穴型导板PeenedHeadPunch镶入式冲头锤击强化冲头钻杆凸模PilotPin定位销导向销子PinGate针尖浇口Plate衬板PreExtrusionPunch顶挤冲头Punch冲头Puncher推杆PusherPin衬套梢Rack机架RappingRod起模杆Re-entrantMold凹入模RetainerPin嵌件梢RetainerPlate托料板ReturnPin回位梢RidingStripper浮动脱模器RingGate环型浇口Roller滚筒Runner流道RunnerEjectorSet流道顶出器RunnerLockPin流道拉梢ScrewPlug头塞SetScrew固定螺丝Shedder脱模装置Shim分隔片Shoe模座之上下模板Shoot流道ShoulderBolt肩部螺丝Skeleton骨架SlagRiser冒渣口Slide（SlideCore）滑块SlipJoint滑配接头SpacerBlock间隔块SpacerRing间隔环Spider模蕊支架Spindle主轴Sprue注道SprueBushing注道衬套SprueBushingGuide注道导套SprueLockBushing注道定位衬套SpruePuller注道拉料浇道推出杆注道残料顶销SpewLine合模线SquareKey方键SquareNut方螺帽SquareThread方螺纹LimitStopCollar限位套StopPin止动梢StopRing止动环Stopper定位停止梢StraightPin圆柱销StripperBolt脱料螺栓StripperBushing脱模衬套StripperPlate剥料板StrokeEndBlock行程止梢SubmarineGate潜入式浇口SupportPillar支撑支柱顶出支柱SupportPin支撑梢SupportingPlate托板SweepT emplate造模刮板TabGate辅助浇口TaperKey推拔键TaperPin拔锥梢锥形梢TeemingPouring浇注ThreeStartScrew 三条螺纹ThrustPin推力销TieBar拉杵TunnelGate隧道形浇口Vent通气孔WortlePlate拉丝模板模具常用之工作机械3DCoordinateMeasurement三次元量床BoringMachine搪孔机CNCMillingMachineCNC铣床ContouringMachine轮廓锯床CopyGrindingMachine仿形磨床CopyLathe仿形车床CopyMillingMachine仿形铣床CopyShapingMachine仿形刨床CylindricalGrindingMachine外圆磨床DieSpottingMachine合模机DrillingMachine钻孔机EngravingMachine雕刻机EngravingE.D.M 雕模放置加工机FormGrindingMachine成形磨床GraphiteMachine 石墨加工机HorizontalBoringMachine卧式搪孔机HorizontalMachineCenter卧式加工制造中心InternalCylindricalMachine内圆磨床JigBoringMachine冶具搪孔机JigGrindingMachine冶具磨床LapMachine研磨机MachineCenter加工制造中心MultiModelMiller靠磨铣床NCDrillingMachineNC钻床NCGrindingMachineNC磨床NCLatheNC车床NCProgrammingSystemNC程式制作系统Planer 龙门刨床ProfileGrindingMachine投影磨床ProjectionGrinder投影磨床RadialDrillingMachine旋臂钻床Shaper牛头刨床SurfaceGrinder平面磨床TryMachine试模机TurretLathe转塔车床UniversalToolGrindingMachine万能工具磨床VerticalMachineCenter立式加工制造中心WireE.D.M线割放电加工机入水Gate进入位GateLocation水口形式GateType大水口EdgeGate细水口Pin-pointGate水口大小GateSize转水口SwitchingRunnerGate唧嘴口径SprueDiameter流道MoldRunner热流道HotRunnerHotManifold温度控制器温控器ThermostatThermoregulatorsT emperatureController 热嘴冷流道HotSprueColdRunner 唧嘴直流DirectSprueGate圆形流道RoundFullHalfRunner流道电脑分析MoldFlowAnalysis流道平衡RunnerBalance热嘴HotSprue热流道板HotManifold发热管CartridgeHeater探针Thermocouples插头ConnectorPlug插座ConnectorSocket密封封料Seal运水WaterLine喉塞LinePlugThroatT aps喉管Tube塑胶管PlasticTube快速接头JiffyQuickConnectorQuickDisconnectCoupling 模具零件MoldComponents三板模3-PlateMold二板模2-PlateMold边钉导边LeaderPinGuidePin边司导套BushingGuideBushing中托司ShoulderGuideBushing中托边GuidePin顶针板EjectorRetainnerPlate托板SupportPlate螺丝Screw管钉DowelPin开模槽PlyBarScot内模管位CoreCavityinter-Lock顶针EjectorPin司筒EjectorSleeve司筒针EjectorPin推板EjectPlatePushPlateStripperPlate缩呵MovableCoreReturnCorePuller 扣机（尼龙拉勾）NylonLatchLock 斜顶Lifter模胚（架）MoldBase上内模CavityInsert下内模CoreInsert行位（滑块）Slide镶件Insert压座Wedge耐磨板油板WedgeWearPlate压条Plate撑头SupportPillar唧嘴SprueBushing挡板StopPlate定位圈LocatingRing锁扣Latch扣机PartingLockSet推杆PushBar栓打螺丝S.H.S.B顶板EjectorPlate活动臂LeverArm分流锥SprueSpreader分流板SpreaderPlate水口司Bush垃圾钉StopPin隔片Buffle弹弓柱SpringRod弹弓DieSpring中托司EjectorGuideBush中托边EjectorGuidePin镶针Pin销子DowelPin波子弹弓Ballcatch喉塞PipePlug锁模块LockPlate斜顶AnglefromPin斜顶杆AngleEjectorRod尼龙拉勾PartingLocks活动臂LeverArm复位键提前回杆EarlyReturnBar气阀Valves斜导边AnglePin术语Terms承压平面平衡PartingSurfaceSupportBalance模排气PartingLineVenting回针碰料位ReturnPinandCavityInterference 顶针碰运水WaterLineInterfereswithEjectorPin 料位出上下模PartfromCavith （Core）Side不准用镶件DoNotUse（CoreCavity）Insert 用铍铜做镶件UseBerylliumCopperInsert初步模图设计PreliminaryMoldDesign正式模图设计FinalMoldDesign弹弓压缩量SpringCompressedlength稳定性好GoodStabilityStable强度不够InsufficientRigidity均匀冷却EvenCooling扣模Sticking热膨胀ThermalExpansion公差Tolerance铜公（电极）CopperElectrode AirVentValve通气阀AnchorPin锚梢AngularPin角梢Baffle调节阻板AngularPin倾斜梢BafflePlate折流挡板BallButton球塞套BallPlunger定位球塞BallSlider球塞滑块BinderPlate压板BlankHolder防皱压板BlankingDie落料冲头Bolster上下模板BottomBoard浇注底板Bolster垫板BottomPlate 下固定板Bracket托架BumperBlock缓冲块Buster堵口CastingLadle浇注包CastingLug铸耳Cavity模腔模穴（模仁）CavityRetainerPlate模穴托板CenterPin中心梢ClampingBlock锁定块CoilSpring螺旋弹簧ColdPunchedNut冷冲螺母CoolingSpiral螺旋冷却栓。
注塑常用术语英文表达
1.雾气Moisture Streaks2。
玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4。
银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7。
黑点Dark Sport8。
顶出印Visible Ejector Marks9。
变形Deformation During Demolding10.填充不足Short Filling11。
冷料流痕Cold Slug12。
进胶口点不良Dull Spots Near The Sprue13。
喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16。
过热变色Burnt Streaks17。
龟裂Stress Crack18。
缩水痕Sink Marks19。
真空气泡Density Bubble20。
披锋Flash21。
擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface 22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch—retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi—cavity mould多浇口multi—gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate ，sprue gate轮辐浇口spoke gate ，spider gate 点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold—slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould，movable half 上模upper mould, upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin，finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine。
注塑方面英语术语共22页文档
注塑方面英语术语压铸 die-cast压炼 injection铸件 casting/cast/founding起泡/气泡 bubble/blister/air bubble缺料 shor-shots/undershot浇不足/*铸 under-founding多料 superfluit ies/superfluous material(alloy)顶针痕 ejector (pins)mark花纹 flowmark/flow line冷纹 coldmark/cold streak油纹 oilstreak走水纹 splash mark银纹 silverstreaks霜纹 splaymark夹水纹 silverstreaks/flow line/weld line扣模/粘模 sprue sticking 砂眼/气眼 air hole（塑胶件）弯曲/变形 warping/warpage变形 deformation扭曲 twist翅曲 warp/warped材料错误 using wrongplastic material凸痕 convex mark凹位/凹陷 sink mark/dentmark披锋 flashing批损 pare-mark/cut mark批凹 pareoff锉纹 trim-mark/file-mark锉损 excessive trim mark黑点/黑纹 black spots/blackstreak发白 white mark烧焦 burnmarks刮花/刮痕 scratch mark擦痕/擦伤 rub-mark/brush-burn裂缝 cracking裂纹 craking line碰损 stress mark起皮 chip错位（合模线） part line misaling ment孔位尺寸改变 dimension various哑色 dull color表面变光滑（喷油面） glossy finishing表面sruface/outside镶件insert/insert word缩水/收缩 sinkmark/shrinkage/shrink mark偏差 color deviation色粉 colourment颜色 colour/color零件污糟 dirty mark onpart顶白 stress mark/ejector mark屈曲 bent夹模线移位 part linemisalignment胶件料厚不均 uneven wall thickness水口料 degradedmaterial凹印 sink mark擦花 abrasion mark混色 contamination mark热点不良 poor heatsticking定位圈 locatingring唧嘴 sprue bush (浇口套)A板 Aplate (定模板)B板 Bplate（动模板）方铁 spacer block (垫铁)底板 bottom clamp plate(动模底板)面板 topclamp plate(定模底板)顶针 ejector pin（顶杆）直边钉 guide pin(导柱)托司 shoulder guide bush(导套)直司 straightguide bush(导柱)回针 returnpin(回程杆)细水口边钉 support pin(副导柱)蓝弹簧 blue spring（回程弹簧）水口推板 runner stripperplate(卸流道板)中边钉 ejector guidepin (顶板导柱)顶针板 ejectorretainer plate(顶杆固定板)顶针底板 ejector plate(顶杆垫板)撑头 support pollar（支撑柱）垃圾钉 stop pin(限位钉)呵core (后模肉内镶件)后模肉 back moldbody(后模镶件)前模肉 cavity（前模镶件）扣鸡 P-lockblister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)毛边flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤(Flow Line)流痕(Weld Line) 熔接线Sink Mark凹陷Streak条纹Warpage翘曲希望以上资料对你有所帮助，附励志名言3条：1、有志者自有千计万计，无志者只感千难万难。
注塑常用术语英文表达
1.雾气Moisture Streaks2.玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4.银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7.黑点Dark Sport8.顶出印Visible Ejector Marks9.变形Deformation During Demolding10.填充不足Short Filling11.冷料流痕Cold Slug12.进胶口点不良Dull Spots Near The Sprue13.喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16.过热变色Burnt Streaks17.龟裂Stress Crack18.缩水痕Sink Marks19.真空气泡Density Bubble20.披锋Flash21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine。
注塑成型术语中英文对照
注塑成型术语中英文对照Material Properties原料物性back pressure背压drying干燥Material supplied使用的原料Colorant or other additives色母和其他添加剂plastication rate(ie.screw RPM)塑化能力（例如：螺杆转速）coolant inlet pressure冷却水（或冷媒）进水口压力cooling channel condition 冷却效果（冷却系统）coolant outlet pressure冷却水出水口压力Coolant flow rate冷却水流量Coolant delta pressure冷却水delta压力fill speed settins填充速度设定Transfer position切换位置（速度转保压）Cooling rate & time 冷却速度和时间Screw run time螺杆储料时间Melt temperature原料融解温度viscosity粘性Screw delay回转延迟Residence or soak time原料滞留时间Barrel temperature机筒温度coolant temperature冷媒（或冷却水）温度Cooling time(Mold clamped time)冷却时间(合模时间）Clamp force锁模力Times:Cycle mold open etc.模居开模时间Clamp force锁模力Hot runner variation热流道变化flow rate流动速率check ring perormance止逆环的表现Injection Pr.Limit注射压力限制Fill speed settings填充速度设定Transfer position切换位置shot size计量尺寸Amount of Material in shot射出量Pressure profile压力曲线Cavity Pr. Setpoint模腔压力设定Pack Speed保压速度（补缩）Hold pressure保压速度（浇口冷却）cavity shape模腔形状。
注塑专业英语
Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡V oid孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra …添加多一点…Reduced … content减少…含量Dr opped/reduced … by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption 预计年/月用量air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模？die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧？goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口？roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量三、模具塑料模具mould of plastics 注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate 底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine一、组织机构及职位二、X X电子有限公司XX Electronics CO., Ltd三、总经理办公室General manager’s office四、企管部Enterprise management department (EM)五、行政部Administration department (AD)六、销售部Sales department (SD)七、财务部Financial department (FD)八、技术部Technology department (TD)九、物控部Production material control department(PMC)十、生产部Production department(PD)十一、模具部Mold manufacturing department, Tooling manufacturing department (TM)十二、品管部Quality Assurance department (QA) 十三、冲压车间Stamp workshop, press workshop 十四、注塑车间injection workshop十五、装配车间Assembly workshop十六、模具装配车间Mold and die Assembly workshop 十七、金属加工车间metal machine workshop十八、电脉冲车间Electric discharge process workshop十九、线切割车间wire cutting process workshop 二十、工磨车间Grinding workshop二十一、总经理General manager (GM)二十二、副总经理Vice-general manager二十三、经理manager二十四、董事长president二十五、副董事长Vice-president二十六、XX部门经理Manager of XX department二十七、主任、主管supervisor二十八、拉长Line leader二十九、组长Foreman, forelady三十、秘书secretary三十一、文员clerk三十二、操作员operator三十三、助理assistant六．物控保质期shelf lifeABC分类法ABC Classification反常需求Abnormal Demand措施信息Action Message活动报告标志Action-report-flag基于活动的成本核算Activity-based Costing (ABC) 实际能力Actual Capacity实际成本Actual Costs调整现有库存量Adjust-on-hand已分配量Allocation替代工序Alternative Routine装配订单Assembly Order装配零件表Assembly Parts List装配Assembly计划自动重排Automatic Rescheduling可达到库存Available Inventory可用材料Available Material达到库存Available Stock可利用工时Available Work可签约量Available-to-promise平均库存Average Inventory欠交订单Back Order倒序计划Back Scheduling倒冲法Back flush未完成订单Backlog现有库存余额Balance-on-hand Inventory批号Batch Number批量生产Batch Production标杆瞄准Benchmarking工时清单Bill of Labor提货单Bill of Lading物料清单Bill of Material分库Branch Warehouse经营规划Business Plan采购员Buyer能力管理Capacity Management能力需求计划Capacity Requirements Planning (CRP) 保管费率Carrying Cost Rate保管费Carrying Cost单元式制造Cellular Manufacturing修改批量日期Change Lot Date修改工序Change Route修改产品结构Change Structure检查点Check Point闭环物料需求计划Closed Loop MRP通用工序标识Common Route ID计算机集成制造Computer-integrated Manufacturing (CIM)配置代码Configuration Code约束管理/约束理论Constraints Management/Theory of Constraints (TOC)依成本的材料清单Costed Bill of Material急需零件Critical Part累计提前期Cumulative Lead Time现有运转时间Current Run Hour现有运转数量Current Run Quantity周期盘点Cycle Counting调整日期Date Adjust有效日期Date Available修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required发货日期Date to Pull空负荷Dead Load需求管理Demand Management需求Demand实际能力Demonstrated Capacity非独立需求Dependent Demand直接增减库存处理法Direct-deduct Inventory Transaction Processing发料单Disbursement List派工单Dispatch List分销资源计划Distribution Resource Planning (DRP) 鼓－缓冲－绳子Drum-buffer-rope经济订货批量Economic Order Quantity (EOQ)工程变更生效日期Engineering Change Effect Date工程变更生效单Engineering Change Effect Work Order工程停止日期Engineering Stop Date例外控制Exception Control呆滞材料分析Excess Material Analysis急送代码Expedite Code加工订单Fabrication Order补足欠交Fill Backorder总装提前期Final Assembly Lead Time 确认的计划订单Firm Planned Order固定订货批量F ixed Order Quantity集中预测Focus Forecasting完全跟踪Full Pegging通用生产管理原则Generally Accepted Manufacturing Practices毛需求Gross Requirements在制品库存In Process Inventory独立需求Independent Demand投入/产出控制Input/ Output Control检验标识Inspection ID厂际需求Interplant Demand库存周转率Inventory Carry Rate仓库库位类型Inventory Location Type库存周转次数Inventory Turnover发送订单Issue Order项目记录Item Record物料项目Item加工车间Job Shop准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time层Level负荷量Load Leveling负荷报告Load Report负荷Load仓位代码Location Code仓位备注Location Remarks仓位状况Location Status按需订货Lot for Lot批量标识Lot ID批量编号Lot Number批量Lot Size低位码Low Level Code机器能力Machine Capacity机器加载Machine Loading外购或自制决策Make or Buy Decision面向订单生产的产品Make-to-order Product面向库存生产的产品Make-to-stock Product制造周期时间Manufacturing Cycle Time制造资源计划Manufacturing Resource Planning (MRP II)主生产计划Master Production Schedule (MPS)物料成本Material Cost物料发送和接收Material Issues and Receipts物料需求计划Material Requirements Planning (MRP) 登陆标志MPS Book Flag MPS多重仓位Multiple Location净改变式MRP N et Change MRP净需求Net Requirements新仓位New Location新组件New Parent新仓库New Warehouse不活动报告No Action Report现有库存量On-hand Balance未结订单Open Order订单输入Order Entry订货点Order Point订货方针Order Policy订货承诺Order Promising订货备注Order Remarks双亲Parent零件清单Part Bills零件批次Part Lot零件编号Part Number零件Part反查Pegging领料单Picking List领料/提货Picking计划订单Planned Order后减库存处理法Post-deduct Inventory Transaction Processing前减库存处理法Pre-deduct Inventory Transaction Processing发票价格Price Invoice采购订单价格Price Purchase Order优先计划Priority Planning产品控制Product Control产品线Production Line生产规划编制Production Planning产品率Production Rate产品结构树Production Tree预计可用库存Projected Available Balance采购订单跟踪Purchase Order Tracking已分配量Quantity Allocation仓位数量Quantity At Location欠交数量Quantity Backorder完成数量Quantity Completion需求量Quantity Demand毛需求量Quantity Gross进货数量Quantity In排队时间Queue Time队列Queue重生成式MRP Regenerated MRP重排假设Rescheduling Assumption资源需求计划Resource Requirements Planning粗能力计划Rough-cut Capacity Planning工艺路线Routing安全库存量Safety Stock保险期Safety Time预计入库量Scheduled Receipt残料率Scrap Factor发送零件Send Part维修件Service Parts发货地址Ship Address发货单联系人Ship Contact发货零件Ship Date发货单Ship Order 工厂日历Shop Calendar车间作业管理Shop Floor Control损耗系数Shrinkage Factor标准产品成本Standard Product Cost标准机器设置工时Standard Set Up Hour标准单位运转工时Standard Unit Run Hour标准工资率Standard Wage Rate状况代码Status Code库存控制Stores Control建议工作单Suggested Work Order约束理论Theory of Constraints (TOC)时间段Time Bucket时界Time Fence单位成本Unit Cost采购计划员Vendor Scheduler采购计划法Vendor Scheduling工作中心能力Work Center Capacity工作中心Work Center在制品Work in Process工作令跟踪Work Order Tracking工作令Work Order工作进度安排Work Scheduling零库存Zero Inventories经济订货批量＝Squat(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本)美国生产和库存控制协会APICS，American Production & Inventory Control Society三十四、产品三十五、连接器connector三十六、端子terminal三十七、条型连接器bar connector三十八、阴连接器Housing三十九、阳连接器wafer四十、线束wire harness四十一、间距space四十二、额定电压rated voltage四十三、额定电流rated current四十四、接触电阻contact resistance四十五、绝缘电阻insulation resistance四十六、超声波焊接ultrasonic welding四十七、耐压withstand voltage四十八、针pin四十九、物料编号part number五十、导线wire五十一、基体金属Base metal五十二、电缆夹cable clamp五十三、倒角chamfer五十四、接触面积contact area五十五、接触件安装孔contact cavity五十六、接触长度contact length五十七、接触件电镀层contact plating五十八、接触压力contact pressure五十九、接触件中心距contact space六十、接触簧片contact spring六十一、插孔socket contact六十二、法兰、凸缘Flange六十三、界面间隙interfacial gap六十四、键Key六十五、键槽keyway六十六、过渡段ramp六十七、屏蔽套shielding六十八、定位基准Datum reference六十九、扁平电缆flat cable ，Ribbon cable七十、柔性印刷电线Flexible printed wiring七十一、多层印制电路Multilayer printed circuit七十二、焊盘pad七十三、图形pattern七十四、间距pitch七十五、负极Negative pole七十六、正极positive pole七十七、回流Reflow七十八、原理图Schematic diagram七十九、单面板single sided board八十、双面板Two-sided board，Double-sided board 八十一、表面安装surface Mounting八十二、翘曲warp，bow八十三、波峰焊wave soldering八十四、编织层braid八十五、同轴电缆coaxial cable八十六、电介质dielectric八十七、电缆中导线的头数ends八十八、外部干扰external interference八十九、填充物filler九十、护套jacket九十一、比重specific gravity九十二、电阻的温度系数Temperature coefficient of resistance九十三、品管九十四、SPC statistic process control九十五、品管保证Quality Assurance九十六、品管控制Quality control九十七、来料检验IQC Incoming quality control九十八、巡检IPQC In-process quality control九十九、校对calibration百、动态试验dynamic test百一、环境试验Environmental test百二、非破坏性试验non-destructive test百三、光泽gloss百四、击穿电压(dielectric) breakdown voltage百五、拉伸强度tensile strength百六、冷热骤变试验thermal shock test百七、环境试验炉Environmental chamber百八、盐雾实验salt spray test百九、绝缘电阻测试验仪Insulating resistance meter百十、内应力internal stress百十一、疲劳fatigue百十二、蠕变creep百十三、试样specimen百十四、撕裂强度tear strength 百十五、缩痕shrink mark, sink mark百十六、耐久性durability百十七、抽样sampling百十八、样品数量sample size百十九、AQL Acceptable Quality level百二十、批量lot size百二十一、抽样计划sampling plan百二十二、OC曲线operation curve百二十三、试验顺序sequence of tests百二十四、环境温度ambient temperature百二十五、可焊性solderability百二十六、阻燃性flame resistance百二十七、生产百二十八、注塑机injection machine百二十九、冲床Punch machine百三十、混料机blender mixer百三十一、尼龙nylon百三十二、黄铜brass百三十三、青铜bronze百三十四、紫(纯)铜copper百三十五、料斗hopper百三十六、麻点pit百三十七、配料compounding百三十八、涂层coating百三十九、飞边flash百四十、预热preheating百四十一、料reworked material百四十二、塑料reworked plastics百四十三、工艺设计process design百四十四、紧急停止emergency stop百四十五、延时time delay七．QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan，产品先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力non-return valve 止回阀shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure/packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Polystyrene 聚苯乙烯（PS）Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin 结晶形塑料Mold materials 模具General-purpose steel 多用途钢tool steel 模具钢Free-cutting steel 高速切削钢case hardening steel 表面硬化钢Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢Nonferrous steel 非铁合金high speed steel 高速钢cast iron 铸铁Steel specification 钢材规格steel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍chrome 铬aluminum 铝Copper 铜brass 黄铜bronze 青铜titanium 钛Processing 钢材的加工方法Harding / quench 淬火nitride 氮化temper 回火anneal 退火Roll 轧制abrasive 研磨，磨损的finish 精加工，抛光（polish）Case-hardening 表面硬化milling machine 铣（锣）床Lathe车床drill 钻床wire cut 线割NC(numerical control ) 数控材料EDM (Electrical discharge machine) 电火花加工Cut steel 开料Precision ground 精密研磨heat treatment 热处理tap 丝锥，攻牙Texture 蚀纹weld 焊接forge 锻压deformation 变形Spraying 喷涂die-cast 压铸Properties 性能Resistance 电阻，抵抗能力abrasion / wear磨损erode / corrode 腐蚀Toughness 韧性yield strength 屈服强度tensile strength 拉伸强度Fatigue strength 疲劳强度break 断裂stress 应力hardness 硬度Humidity / moisture 潮湿，湿气roughness 粗糙度parameter 参数Thermal conductivity 导热系数manufacture 制造，加工drawback 缺点Ductility 延展性grain 晶粒property 性能，财产brittleness 脆性GD&T （Geometric Dimensions and Tolerance ）形位尺寸公差Flexural strength 挠曲强度impact 冲击conductivity 传导性，导电性Optical 光学的transparent 透明的insulation 绝缘Mechanical 机械的processability 可加工性能timeyield 蠕变Physical 物理的flow rate 流动速率compressive strength 压缩强度Adhesive 粘附的，胶合durability 耐用性Mold design 模具设计Tooling specification 模具规格mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空，间隙undercut 倒扣flush 插入，埋入legend 图例Groove 凹槽latch 插销class 类型，种类plan 平面图Orifice 孔，口column 柱位boss 凸台standard 标准，规格Rib 骨位tapered interlock 锥形管位块Bubbler 炮隆Bolt 螺钉，销顶identification mark 铭牌P/L strip 锁模片Overflow well / cold-slug well 冷料井Vent 排气pocket 槽Gate location 入水点full line 实线broken line 虚线Retainer 固定，支撑operator 操作者（啤工）receptacle 插座Lifting hole 吊令孔insulation plate 隔热板cavity number 型腔号Bolster 支撑，垫子vent channel 排气槽leak / filter 渗漏Leak test 试运水stamp / engrave 雕刻，印记（打字唛）Clamp slot 码模槽support button / pin 垃圾钉cut steel 开料Lodge 安装，放置inlay 镶嵌，插入cam / lifter 斜顶Stripper推方lifting bar 吊模方sprue 唧咀tolerance 公差Counter bore 沉孔slant 倾斜，斜面conical 圆锥的，圆锥形的Bolt 螺栓manifold 热流道板prototype tooling 原型试验Gusset 角撑reverse mold 倒装模constrain / restrict约束，限制Counter lock 反锁thermocouple 热电偶moldmaker 模具制造商Asset / property number 资产编号tool product destination 模具生产地点Accelerating ejection 加速顶出hydraulic 液压的pneumatic 气动的Trapezoid 梯形的semi-round 半圆形format 格式baffle 隔水片Electrode 电极，铜公spare part 配件gall 磨伤，插伤Cable 电缆，电线plating / coating （电）镀bonding / joint 接头Wall transition 壁厚过渡Product problem 产品问题Troubleshoot 故障处理reduce(add) plastic 减（加）胶Burr/flash披峰Burn mark 烧焦ejector mark 顶针印，顶白black specs 黑点，黑斑Discoloration 混色，污点gloss 光泽jetting/worming 走水纹Sink mark 缩水void / bubble 气泡，夹气distortion 变形Warpage 翘曲short molding / non-fill缺胶，未走齐Weld line / knit line 夹水线discarded as useless 报废Split line 夹线stick in sprue bushing / cavity / core 粘唧咀/前模/后模Break / crack 顶裂brittleness 脆性，易脆Others 其他Invoice 发票，清单vendor(er) 卖方vendee 买方guideline 方针，指导Intricate 复杂的confidential 机密的，不可外泄的proprietary 私有的Authorize 批准，授权recipient 接收者issue ①发布，提供；②问题Approve 确认，赞成requirement 需要，必需物const 常数，常量Regarding 关于，涉及opposite 相反的，对面的latitude 纬度，纵向的Version 版本definition 注释，解说transversal 横向的，截线Profile 轮廓，剖面eliminate / cancel 取消allow / permit 允许，许可Respective 各自的，分别的individual 单独的decrease 减少increase 增加Preliminary 初步的approximately 大约，近似estimate / valuate估计，预算Adjust 调整，校准application 应用，申请maintain 维持Accurate / precise 精确的smooth 光滑，顺畅的device 装置，设备Convenient 方便的deadline 截至日期available 有用的，有空的Shift 轮班，换班critical 关键的，临界的exceptional 异常的，优异的Exceed 超过layout 布局，方案loss 损失，消耗install 安装，安置Rotation 旋转item 条款，项目quotation 报价stabilize 稳定Quality 质量quantity 数量couple 连接，接合configuration 构造，外形Illustrate 图解说明simulation 模拟，仿真recommend 推荐使用。
注塑常用术语英文表达
1.雾气Moisture Streaks2.玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4.银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7.黑点Dark Sport8.顶出印Visible Ejector Marks9.变形Deformation During Demolding10.填充不足Short Filling11.冷料流痕Cold Slug12.进胶口点不良Dull Spots Near The Sprue13.喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16.过热变色Burnt Streaks17.龟裂Stress Crack18.缩水痕Sink Marks19.真空气泡Density Bubble20.披锋Flash21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush 直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine（注：文档可能无法思考全面，请浏览后下载，供参考。
注塑常用英语
一、浇口(入水)：gate浇口进入位置：gate location浇口形式：gate type大水口(2板模)：edge gate, side gate细水口(3板模)：pin-point gate浇口大小：gate size转开关流道：switching runner/gate唧嘴直径：sprue diameter二、流道：runner热流道：hot runner，hot manifold温控箱：temperature controller热嘴冷流道：hot sprue/cold runner唧嘴直流：direct sprue gate圆形流道：round(full/half) runner模流道电脑分析：mold flow analysis流道平衡：runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探温针：thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socket 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold导柱(边钉/导边)：leader pin/guide pin导套(边司)：bushing/guide bushing顶针板：ejector retainer plate托板：support plate螺丝：screw管销(管钉)：dowel pin内模管位锁：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector sleeve pin推板：stripper plate缩呵：movable core，return core，core puller扣机(尼龙拉勾)：nylon latch lock斜顶：lifter模胚(架)：mold base上内模：cavity insert下内模：core insert行位(滑块)：slide镶件：insert压座(斜鸡)：wedge，heeled block耐磨板/油板：wedge wear plate压条：guide way plate模顶(撑头)：support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.S.(socket head shoulder screw) 杯头螺丝：S.H.C.S.(socket head cap screw)活动臂：lever arm分流锥：sprue separator垃圾钉：stop pin水隔片：buffle弹弓柱：spring rod弹弓：die spring中托司：ejector guide bush中托导套(边)：ejector guide pin镶针：insert pin波子弹弓：ball catch喉塞：pipe plug行位斜导柱：angle pin斜顶杆：angle ejector rod复位键/提前回杆：early return bar气阀：valves五、术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模闭合总厚度：mold base shut height顶针碰运水：water line interferes with ejector pin料位出上(下)模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate，core direct cut on B-plate.不准用镶件：do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步(正式)模图设计：preliminary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length强度不够：insufficient rigidity均匀冷却：even cooling扣前模：sticking热膨胀：thermo expansion公差：tolerance铜电极(铜公)：copper electrode石墨电极：graphite electrode夹线：weld line翘曲：warpage缺胶：short shot困气：air trap毛刺：flash，burr~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡Void 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PT FE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/tensile etc 物理性能低High flow/filler content etc 流动性/填充…过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为… High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra … 添加多一点…Reduced … content 减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by … 预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量。
注塑、模具行业术语：英汉对照版！
注塑、模具⾏业术语：英汉对照版！（⼀）模具专业基本⽤词 Professional Terms1．塑料 — plastic, resin2．样件 — sample3．钢料 — steel4．注塑机 — injection machine, press5．产品 — part, product, moulding6．模具 — mold, mould, toolA 简易模（样板模）— prototype moldB 量产⽤模具 — production mold7．三维造型（数模）—3D model, 3D data8．⼆维产品图 — 2D part drawing9．设计 — design10．制造 — manufacture, build up, construction, fabrication, make11．检验 — check, inspection12．测量 — measure, inspection13．修改 — change, modify, correction14．⼯程更改 — engineer change15．质量 — quality16．数量 — quantity17．基准 — datum, reference（⼆）如何解析2D 产品图？How to read 2D part drawing?⼀．产品⼏何 Geometry1．点 — point2．线（边） — line, edge3．⾯ faceA 侧⾯ — sideB 表⾯ — surfaceC 外观⾯ — appearance surface4．壁厚 — wall thickness, stock thickness5．加强筋（⾻位） — rib6．孔 — hole7．细长的槽 — slot8．柱位 — boss9．⾓ — cornerA 圆⾓ — filletB 倒⾓ — chamferC 尖⾓ — sharp corner10．斜度 — angle, taper11. 凹槽—recess , groove⼆. 分模信息 Splitting1．分型线 — parting line (P/L), splitting line2．主分模⽅向 — main direction, line of draw3．浇⼝设定 — gating⼀．产品标识 Part Identification1．产品名称 — part name (P/N)2．产品编号+版本号 — part number + revision (Rev.) 3．型腔号 — cavity number4．材料标记 — material symbol5．模具编号 — mold number (no.)6．⽇期印 — dating insert, date code7．循环印 — cycling code8．公司标志 — company logo⼆. 技术要求 Specification (Special Requirement)1．项⽬启动表 Kick-off sheet1）项⽬名称 — program name, project name2）产品名称 — part name, product name, part description3）产品编号 — part number (P/N)4）客户模号 — customer mold no.5）项⽬启动⽇期 — kick off date, start date6）项⽬完成⽇期 — due date, lead time7）内模件⽤钢 — tool steel8）型腔数量 — number of cavities9）数据⽂件编号 — data file no.10）注塑材料 — resin, plastic, raw material11）收缩率 — shrink, shrinkage, shrink factor12）注塑机吨位 — molding machine size, injection machine size 13）成型周期 — cycle time14）型腔光洁度 — cavity polish15）型芯光洁度 — core polish16）⽪纹（晒纹）— texture, grain17）拔模斜度 — draft angle, removal taper18）注塑件颜⾊及光泽 — molded color & gloss19）模具加⼯地 — manufacturing facility20）热流道供应商 — manifold manufacturer, manifold supplier 21）浇⼝位置 — gate location / position22）浇⼝类型 — gate type产品标识 — stamp information, part identification特殊要求 — special instructions1．产品质量及外观要求 Part Quality & Appearance Requirement 1）尺⼨及公差 Dimension & Tolerance①重要尺⼨ — critical dimension, important dim., key dim.②理论尺⼨ — nominal dimension③实际尺⼨ — actual dimension④公差 — tolerance⑤公差带 — tolerance range⑥尺⼨超差 — dimension deviation⑦接受（合格） — accept, OK⑧拒绝（不合格） — reject, refuse, obsolete, NG⑨让步接受 — concession, special admit⑩返⼯ — re-work2）产品缺陷（常见的）Defects (normal)①缩⽔ — sink mark, shrinkage②飞边，⽑边 — flash, burr③段差 — mismatch discrepancy④银丝纹，蛇纹 — snake marks, streak⑤弯曲，变形 — warpage, distortion⑥打不饱（缺料） — short shot⑦熔接线 — weld line⑧多胶— unwanted plastic⑨拉伤—damage2．产品外观 Part Appearance①产品颜⾊ — part color②产品光泽 — gloss③⽪纹粒度 — grain3．常⽤词汇、词组及短语 Normal Word, Short Sentence1）单边 — per side2）双边 — both sides3）加⼊，添加 — add, incorporate4）去除，取消 — remove, cancel5）满⾜…的要求，符合，与…要求⼀致 — according to, conform to, satisfy, meet 6）要求，需要 — require, need, demand7）确认 — be approved, agreed by …8）允许 — permit, allow9）在…范围之内 — within10）不可以，不允许，禁⽌ — free from, prevent, avoid11） …，除⾮有另指 — … unless otherwise specified12） …或少于 — …or less13）⾃动化运作 — automatic operation14）未注尺⼨（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.15）分型线上的飞边（披缝）或段差应⼩于…Burrs or discrepancy on the P/L shall be … or less.标题栏 Title Block1．产品名称 — part name2．图纸编号 + 版本号（索引号）— drawing no. + level (index)3．⼀般公差 — general tolerance（三）如何阅读制模标准？How to read tooling standard?⼀．模具结构术语 Mold Construction TermsA．模架 Mold Base1．模架量化特征 Measurement Feature①长 X 宽 X ⾼ — Length X Width X Height②模具⾼度尺⼨（模厚） — stack height of mould③模具重量 — total weight of mould, mould thickness2．定模底板 — front plate, top clamping plate, clamp plate, clamping plate 3．定模板 — cavity plate, fixed mould plate, A – plate4．动模板 — core plate, moving mould plate, B – plate5．⽀撑板 — support plate, backing plate6．间隔板,⽅铁 — support blocks, rails, risers, spacer block7．顶杆固定板 — retaining plate, ejector retaining plate8．顶板 — ejector plate，bottom clamping plate9．动模底板 — back plate10．导柱 — guide pillar, leader pin, guide pin11．导套 — guide bush, leader pin bush12．复位杆 — return pin, push-back pin13．弹簧 — spring14．撑头 — support pillar15．顶针板导柱、导套 — ejection guide pin / bush 16．垃圾钉 — stop pin, stop button17．模脚 — standing-off pillars18．标牌 — plaque scutcheonB．成型零部件 moulding components1．型芯 — core insert2．型腔 — cavity insert3．镶针 — core pin4．镶块 — sub-insert, split5．滑块 — slide, sliding split6．斜顶 — lifter, angled-lift split, loose coreA 斜顶头 — lifter headB 斜顶杆 — lifter rod, lifter shaft7．成型顶杆 — moulding face pin, form pin C．浇注系统 Feed System1．塑料 Mouldinga．主流道 — sprueb．分流道 runner①主分流道 — main runner②⼆级分流道 — branch runner分流道断⾯形状 cross-sectional shape of runner①圆形 — full round②半圆形 — semicircular③梯形 — trapezoidalc．浇⼝ gate常⽤浇⼝形式 normal gate type :①边缘浇⼝（J型浇⼝） — edge gate, J – gate②侧浇⼝ — side gate③潜伏式浇⼝ — sub-gate, subsurface gate, submarine gate, cashew gate④潜伏式⼆次浇⼝(隧道式浇⼝) — tunnel gate onto feeder post⑤点浇⼝ — pin gate⑥直接浇⼝(主流道型浇⼝) — sprue gate, direct gate⑦护⽿式浇⼝ — tab gated．模腔 — impressione．冷料井 — cold slug wellf．热流道 — hot runner2．模具零件 mold componentsa．定位圈 — locating ring, location ring, register ringb．浇⼝套 — sprue bushc．挡圈 — stop ringd．浇⼝镶块 — gate inserte．热流道板 — manifoldf．热嘴 — hot drophot sprue分型⾯及其锁紧、排⽓ Parting Surface, inter-locking & venting1．分型线 — parting line ( P/L )2．镶拼线 — bodyline, joint line3．平 / 不平的分型⾯ — flat / non – flat parting surface4．封胶⾯ — shut off surfaces, seal-off surfaces5．擦穿位 — shut off6．碰穿位 — kiss-off7．管位 — parting line lock8．分型⾯的释放(避空) — relief of parting surface9．分型⾯的平衡 — balancing of parting surface10．锁紧⾓度 — locking angle11．锁紧⼒ — clamping force12．锁模块 — safety strap13．精定位 — Interlock, die lock14．困⽓ — air trap15．排⽓槽 — vent, vent slotE．滑块机构 Slide1．驱动 Actuation①斜导柱 — angle pin, horn pin, cam pin②弹簧 — spring③油缸 — hydraulic cylinder2．制动 Detention①滑块固定器 — slide retainer②弹簧制动器 — spring-loaded detention (plunger)③挡钉、挡板 — stop pin, stop plate, slide stop3．导轨 — gib, guide strip4．锁紧块（楔紧块）— heel block, locking heel, wedge block, chase block 5．耐磨⽚ — wear plate, wear strip6．压板 — retainer, gib7．螺钉 — screw8．定位销 — dowel pinF．斜顶机构 Lifter1．斜顶头 — lifter head2．斜顶杆 — lifter rod, lifter shaft3．开⼝销 — split pin4．固定板（压板） — retainer plate5．耐磨⽚ — wear plate6．铜导套 — bronze bushing7．衬套 — spacer8．导轨 — L – gib9．滑动块 — slideG．顶出系统 Ejection System1．基本词汇 Basic Word①顶出⾏程 — ejection stroke②模具开档 — daylight③粘模 — stick④产品脱模 — part is push off from, clear part of mould, separation of part2．顶板机构 Ejector plate assembly①顶板 — ejector plate②顶板固定板 — retaining plate③推板— stripper plate④推板导柱 — ejector guide pin⑤推板导套 — ejector guide bush⑥撑头 — support pillar3．复位机构 Return System①复位杆（回程杆）— return pin, push – back pin②垃圾钉 — stop pin, stop button③压簧 — compressed spring④碟簧 — a stack of ―Belleville‖ washers⑤早复位机构 — early return system⑥强制复位机构 — positive return system4．顶出⽅法 Ejection Techniques1）顶杆顶出 — pin ejection2）顶管顶出 — sleeve ejection3）顶块顶出 — bar ejection4）扁顶顶出 — blade ejection5）顶板顶出 — stripper ejection6）油缸顶出 — hydraulic ejection7）⽓顶 — air ejection8）阀门顶出 — valve ejection5．顶出元件 Ejection Elements1）拉料杆 — sprue puller, sucker pin2）顶杆 — ejector pin3）阶梯式顶杆 — stepped ejector pin1）顶管 — ejection sleeve, sleeve2）扁顶 — ejector blade, slabbed off ejector pin 3）顶块 — stripper bar4）顶环 — stripper ring5）推板 — stripper plate6）加速顶 — accelerated ejection1．顶出辅助机构 Supplementary operating system1）弹簧柱塞器 — spring – loaded plunger2）弹珠定位器 — ball catch system3）插销式锁扣 — Latch – lock4）尼龙拉杆装置 — friction puller device2．电器元件 Electric Components1）压⼒传感器 — pressure transducer2）限位开关 — limit switchF．冷却系统 Cooling System1．基本词汇 Basic Word1）温差 — temperature variation2）⽔孔（⽔道） — waterlines, water-ways, flow-way, channel3）⽔路 — cooling circuit4）⽔路⽰意图 — water schematic, schematic circuit5）冷却液 — coolant, coolant fluid6）内连接 — interconnect7）外连接 — external connection8）出⼝、⼊⼝ — outlet、inlet9）漏⽔ — water leakage2．⽔路分布 Circuits1）阶梯式⽔路 — stepped system2）分隔板⽔路 — baffled hole system3）斜孔式⽔路 — angled hole system3．⽔路元件 Components1）闷头（螺塞、⽌⽔栓） — （threadless）brass pressure plug : female plug & male 2）隔⽔⽚ — baffle3）密封圈 — O – ring4）快插⽔路接头 — quick disconnect fitting, quick connection adaptor 5）弯头 — elbow6）偶合器（连接器、接头） — adaptor (including a plug & a socket) 7）橡⽪管 — rubber hose1）分⽔板,集⽔块 — water manifoldG．螺纹、螺纹孔 & 螺钉 Thread, thread hole & screw1．螺纹 — thread2．管螺纹 — pipe thread3．螺纹孔 — screw hole, tapped hole4．起吊孔 — handling hole, jack screw hole, eye bolt hole5．螺钉 — screw6．内六⾓螺钉 — socket headed cap screw （s.h.c.s.）7．沉头螺钉 — flat headed cap screw （f.h.c.s）8．螺栓 — bolt9．螺母 — nut10．锁紧螺母 — locknut11．螺纹标准 Thread Standard①公制标准 — Metric②英制标准 — Imperial③英制管螺纹标准 — British Standard Pipe thread （BSP）④美制管螺纹标准 — NPT⑤美制粗螺纹标准 — United Coarse thread （UNC）⑥美制细螺纹标准 — United Fine thread （UNF）H．润滑 Lubrication1．润滑槽 — grease groove2．加油管 — grease line3．油杯 — lubrication fittingI. 测量仪器 Measuring Instruments1．游标卡尺 — vernier caliper2．千分尺 — micrometer3．⾼度规 — height gauge4．刻度规 — dial gauge5．三坐标测量仪（三次元） — Coordinate Measure Machine（CMM）6．塞规 — pin gauge7．圆⾓量规 — radii gauge8．轮廓投影机—profile projectorJ．注塑机参数 Injection Machine Parameter1．注塑机规格参数 Injection Machine Specification①锁紧类型 clamp typea．油缸 — hydraulicb．肘杆式 — toggle②垂直注塑机导柱间距 — tie bar vertical clearance③⽔平注塑机导柱间距 — tie bar horizontal clearance④台板尺⼨ — platen dim.⑤最⼩ / 最⼤模厚 — mold height Min. / Max., Min. / Max. mold thickness⑥最⼩ / 最⼤注塑机开档 — open daylight Min. / Max.⑦锁紧⾏程 — clamp stroke⑧锁紧⼒ — clamping force⑨顶出⾏程 — ejector stroke⑩顶出⼒ — ejector force !你想成为学霸吗。
模具注塑术语中英文对照
模具注塑术语中英文对照1. 模具制造工艺 - Mold Manufacturing Process•钳工技术 - Fitting Technology•铣床 - Milling Machine•车床 - Lathe Machine•电火花 - Electrical Discharge Machine (EDM) •线切割机 - Wire Cutting Machine (WCM)•抛光 - Polishing•喷砂 - Sandblasting•组装 - Assembly•检验 - Inspection•测试 - Testing2. 模具材料 - Mold Materials•CNC - Computer Numerical Control•冷/热工作钢 - Cold/Hot Work Steel•韧性铁 - Ductile Iron•钢筋混凝土 - Reinforced Concrete•铝合金 - Aluminum Alloy•有机玻璃 - Organic Glass•尼龙 - Nylon•聚酯树脂 - Polyester Resin•低密度聚乙烯 - Low-Density Polyethylene (LDPE) •高密度聚乙烯 - High-Density Polyethylene (HDPE) 3. 注塑设备 - Injection Molding Equipment•注塑模 - Injection Mold•注塑机 - Injection Molding Machine•螺杆 - Screw•加热筒 - Barrel Heater•喷嘴 - Nozzle•冷却系统 - Cooling System•熔融体 - Melted Polymer•定位环 - Locating Ring•压力机 - Press•模芯 - Core4. 注塑工艺 - Injection Molding Process•熔胶温度 - Melting Temperature •注射速度 - Injection Speed•保压时间 - Holding Time•冷却时间 - Cooling Time•射胶压力 - Injection Pressure•模具温度 - Mold Temperature•注射容量 - Injection Capacity•射出比例 - Injection Ratio•射胶速度 - Injection Rate•开模时间 - Opening Time5. 注塑缺陷 - Injection Molding Defects•缩水 - Shrinkage•气泡 - r Bubbles•热分解 - Thermal Degradation•断裂 - Fracture•变形 - Deformation•熔接线 - Weld Line•流痕 - Flow Mark•挤出线 - Extrusion Line•色差 - Color Variation•异物 - Foreign Object6. 模具维护 - Mold Mntenance•涂抹脱模剂 - Apply Mold Release Agent•清洁模具 - Clean the Mold•磨削模具 - Grinding the Mold•检查模具 - Inspect the Mold•修复模具 - Repr the Mold•涂覆保护液 - Coat with Protective Agent•封存模具 - Store the Mold•更换模具配件 - Replace Mold Components•消除模具表面缺陷 - Eliminate Surface Defects on Mold •升级模具材料 - Upgrade Mold Material以上是模具注塑术语的中英文对照，希望能对你有所帮助。
注塑常用术语英文表达
1.雾气Moisture Streaks2.玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4.银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7.黑点Dark Sport8.顶出印Visible Ejector Marks9.变形Deformation During Demolding10.填充不足Short Filling11.冷料流痕Cold Slug12.进胶口点不良Dull Spots Near The Sprue13.喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16.过热变色Burnt Streaks17.龟裂Stress Crack18.缩水痕Sink Marks19.真空气泡Density Bubble20.披锋Flash21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine。
注塑专业名词
注塑专业名词中英文对照表英语名称中文名称Hopper Dryer 料斗干燥器Injection Molding Cycle 注塑周期Crushing Mill 粉碎机Precision Injection 精密成形Gas Injection/AGI 吹气成形、气辅成形Set the condition 设定注塑前提Machine 机械Mold Set-Up 上模Screw 螺杆、螺钉、螺旋Mold Down 下模Screw Head 螺杆头Pressure 压力Joint 接头，接缝Low Pressure 低压Injection 注塑Low Pressure Clamping 低压锁模Feeder 送料（加料）器Holding Time 保压时间Compound 混炼料Back Pressure 背压Blend 搅浑，调和Clamping Force 合模力Mixer 混淆器Hold Clamping Pressure 锁模型压成力Mixing 混淆Clamping Stroke 合摸行程Cooling 冷却Clamping Unit 锁模装配Cooling Tower 冷却塔Mold Opening 开模Chiller 冷水机Mold Closing 合摸Temperature Controller 温调机Speed 速率Cylinder 料筒Injection Speed 射出速率Heater 加热器Injection Capacity 注塑量Band Heater 加热圈Charging 计量Thermocouple 热电偶Charging Stroke 计量行程Nozzle 射嘴Rib 骨位，筋位，增强筋Nozzle Head 射嘴头子Insert 嵌件，镶嵌"Tie Bar,Tie Rod" 拉杆，拉杠Wall Thickness 胶厚，壁厚Distance Between Tie Rods 拉杆距离Plasticizing 塑化Limit Switch 限位（限定）开关Thermal Decomposition 热分化Operation Switch 操作开关Shrinkage 收缩Operation Guide 操作指南Resin 树胶Control Panel 节制器Material 原料，质料Automatic 全自己主动Plastics 份子化合物塑料，塑胶成品Semi Auto 半自己主动Rubber 橡胶Hand 手动Master Batch 色母Handle 手柄Powder 色粉，粉，粉末Extruder 押出机，挤塑机Dry Color 色粉，干色料Extrusion Molding 挤塑Pellet 粒，塑胶粒Blow Molding Machine 吹塑机"Glass Fiber,Fibrous Glass" 玻璃纤维Blow Molding 吹塑Hose 软管，管Program Control 步伐节制Over Packing 过充填Process 工艺，工序，历程Mold Mark 马克模伤，模痕Inject visor 注塑工艺步伐节制装配Shock 冲击Damage 损坏，毁伤Cold Slug 冷料Sink 马克抽水，紧缩Cold Slug Well 冷料井Short Shot 充填不足，欠料Freeze 冷凝Flash 毛刺，披峰Hydraulic 液压，油压String Flash 胶丝Ghydraulic Ejector 液压顶出，液压脱模White 马克白化，顶白Hydraulic Pump 液压泵Silver 雪白，银痕Hydrautic 摩托液压电动机Flow mark 流纹air compressor 空气压缩机，空压机burn 烧黑，烧焦oil leakage 漏油异物black spot 异物，黑点oil tank 油箱，油槽sticking 粘模piston 活塞weld 溶接线，联合线air cylinder 气缸flash 料花alarm 报警oil 马克油污，油渍safety gate 太平门damage 打痕，击伤emergency stop 紧迫遏制cracking 裂，开裂color change 换色jetting 气纹purge material 清机份子化合物塑料deform 变型resin thermal 胶料温度warping 屈曲，翘曲，外倾mold thermal 模温bend 屈曲，翘曲，外倾heat up 升温，升热torsion 扭曲air shot 空射蛟，空打uneven color 色彩不均匀try 试模Eccentric Wall thickness 壁厚不匀称mold release 脱模"bladder,cell" 气泡儿，浮泛，空地mold release agent 脱模剂stripes 条纹rust preventatives 防锈剂dirty 污痕，污点，渗溢can't release （产物）没有办法脱模flaking 脱落，剥落shot 注，射tear off 上下翻动gate 进点，浇口float 浮起center gate 中间浇口screw damage 螺钉滑牙sprue runner 水口，注口，流道料shortage 员数不足，欠品clearance 距离，余隔run out 跃动度，偏疼sprue 主流道注（塑）口contraction 紧缩runner 流道，流道料assembly NG 嵌合不良，装配不良air vent 散气眼，透风口stress 应力breathing 排气，散气internal stress 内部策应力anneal 热措置惩罚，退火preparation 摆设，筹办mold 生产模型stopper 挡块machining center 加工中间stripper 推板，脱模型板universal milling machine 刨床，锣床spacer plate 垫板latter 车床mould base 模胚surface grinder 最简单的面磨制机床support plate 托板grinding drilling 钻床support pillar 撑头electric discharge machine 火花机加工puller lock 拉塞wire EDM 线割切puller bolt 拉杆nitride steel 氮化钢取付板top clamp plate 工字板，水口板nitrogen 氮气bottom plate 底板nitride 氮化措置惩罚return 回针titanium 钛guider pin 导柱heat treatment 热措置惩罚guider bush 导套hardening 淬火die 生产模型，动模，移动模型板Temper 回火die plate 模型板，载模型板annealing 退火module 板块，模件，模数pre harden 预加硬钢parts 零件，生产模型零件hardness 硬度eye bolt 吊环螺栓soft 软，软的crane 吊车，行车electrodes 铜公hook 勾，吊勾insert 镶件wire 钢丝，钢丝绳slide 行位，滑块file 锉子taper 斜度oil stone 油石taper 斜度，锥度，锥形的sand paper 砂纸draft 脱模斜度mesh 节号，目guide pin 导向柱刻印engrave 刻印sleeve pin 司筒针texture 蚀纹square pin 扁顶针放电目EDM texture 火斑纹angular ejector 斜顶针rough 粗的cavity 模腔，前模，母模trifling 细的，幼的core 模心，后模，公模diamond cut 钻石纹number of cavities 取数，模腔数roulette 滚花刀，刻痕rocket ring 定位环blast 喷沙o ring O环，胶圈hot runner 暖流道wall trickness 肉厚，胶厚repair 补缀add material 加胶接welding 溶接，焊接building 加胶溶接机welder 焊机，电焊机cut material 减胶溶接棒welding rod 焊条，电焊条modify the tooling 改模（因设变补缀）argon arc welder 氩弧焊repairing the tooling 生产模型补缀torch bumper 喷燃烧现象器，火苗燃烧现象器design 预设ejector pin 顶出design drawing 预设图ejector pin 顶针design change 预设变动，设变gate type 水口体式格局designer 预设者，预设职员tunnel gate 隧道式浇口，潜入水下口designer 预设者pin point gate 针孔形浇口，细水口mold design 生产模型预设side gate 侧水口，洪流口mold specification 生产模型建造仕样书direct gate 直接浇口specification 规格multi gate 复式浇口mold construction 生产模型机关，生产模型布局fan gate 扇形浇口input 输入film gate 扇形浇口programming 编程jump gate 搭接浇口3D drawing 3D图，3维图gate balance 浇口均衡2D drawing 2D图，最简单的面图undercut 凹槽，倒扣front elevation 正面图cooling line 水管，运水plan 平面图cross-sectional drawing 剖面图cooling 冷却回路，运水CAD date CAD数值modeling 模mock-up 模子，原尺寸模子software 软体hand made sample 手板，手工样品mold drawing 生产模型图module 模数，模量，模件part drawing 零件图gear 齿轮，传动装配diagrammatic sketch 草图helical gear 螺旋齿轮drawing 绘图solid 群体的，固体revised drawing 图订变换transformation 变换，转换dimensioning 记入尺寸floppy disk 磁盘，软盘out mold direction 出模标的目的computer 台式机，计较机draft 出模斜度personal computer 私家用电器脑，手提台式机pitch 间距，齿距version 情势，品类（译文，翻译，译本）angle 角度reading 读取projected area 投影平面或者物体表面的大readout 读出taper 锥度，斜度reading 度数under cut 倒扣压缩compression 压缩2 plate 两板模开open 打开，读出文件（软体）3 plate 三板模not open 打（解）不开，读不出offset 偏置，偏移miss 纰缪，掉误mold layout 分模condition of the progress 进程项度状态split mold 对于开式生产模型finishing 打光，磨光slide core 滑动模芯polish 研磨，打磨loose core 勾当模芯target 方针，目的，对于准loose mold 勾当生产模型schedule 每一日安排表press 冲压，压床，压maintenance 维护，调养press machine 冲床did casting 压铸progressive 级进sintering 加热使黏结single 单冲monkey 勾当板子packing plate 垫板clamp 夹具（固定生产模型用）punch 冲头，凸模，冲床scrap 废铁，废物，废渣punch press 冲孔机rust 生锈die 下模rust inhibitor 防锈剂die set 模座，模架washing agent 洗濯剂press mold 冲压模，五金模ultrasonic cleaning 超音波洗濯leveler 整平滚，矫平机feeder 送料机，加料机burr 反边，毛刺drawing 拉伸thinner 天纳水，淡薄剂burring 去毛刺triclinic 三氯乙烯脱脂剂blank 复合trivalent chromium 六价铬cutting 落料，冲孔bending 折弯degreasing 脱脂，去油bend 折弯，屈曲harmful metal 有害物box-bending 箱cut 割切L-bending L折弯"press, sheet metal" 板金V-beding V折弯cut 堵截，割断punching 冲孔，钻孔iron plate 铁板SECC 镀锌板cutting 冲压，抽去silver top 镀锌板shirk 避空stainless 不锈钢calking 铆接copper 铜tap 螺丝攻brass 黄铜dies 板牙steel 钢reamer 铰孔aluminum 铝reamer 铰刀，扩孔器width 宽度end mill 刨刀thickness 板厚grinder 砂轮机，磨制机床density 疏密程度barrel 滚筒coil 卷材barrel tumbling 滚（捅抛）光width cut 片材plating 电镀nut 螺丝帽，螺帽electro plating vacuum 真空电镀bolt 螺栓，螺杆spot welding 点溶接，点焊chrome plating 镀铬jip 夹具，治具galvanization 镀锌clearance 间隙shave 切，削matching 接口assembly 装配，组装counter 统计器assembly unit 装配组件count method 统计法assembly time 装配工数timer 按时器line 生产线，拉线digital 数码（的），数码self 单人装配digital camera 数码拍照机conveyer 传送带connect 插座，插嘴U line U形出产线plug 插头，瓶塞capacitor 电器皿lamp 灯resistor 电阻器lighting 点灯，灯亮diode 二极管fuse 断电丝LED （light-emitting diode) 闪光二极管power code 电源线transistor 形成品体体管wire hamess 电线导线IC 集成电路bar code 条纹码lcd(liquid crystal display) 液态品体预示器vinyl tape 绝缘带sensor 传感器noise 异音，杂音，噪音relay 替续器decibel 分贝（声强单位）connector 保持器instruction sheet 功课引导书transformer 变压器access platform 功课台breaker 断路器series 串联buzzer 蜂鸣器parallel 并联printed circuit board/PCB 印刷电路板clutch 联轴器，聚散器driver 螺钉刀，起子solenoid coil 电磁线圈driver 十字批（起）coil 线圈driver 一字批（起）static electricity 静电electric drive 电动螺钉刀，电批prevent electricity 防静电torque 扭矩，转矩fan motor 电扇电动机screw 螺钉刀，起子grease 润滑washer 垫圈（片）apply 涂油e-ring 卡环block copy 底板，草图solder 焊锡film 胶卷，软片soldering iron 烙铁silk print 丝印tin 锡pat print 移印earth 接地，地线hot sample 烫印alcohol 火酒，乙醇ink 印字油墨foot switch 脚踏开关color sample 色板terminal 端子print NG 印刷不良terminal block 端子板bleeding 渗溢，飞油label 标贴，标签stamp 捺印bar code 条纹码，条形码spray 涂装，喷涂mile 软片，聚酯树胶wood graining 木纹加工quality control 品位办理sample 样品，样本，样板inspection 查抄boundary sample 限度样板IQC 验收，受入查抄approval sample 认可样板OQC 出货查抄tolerance 公役PQC 工程查抄plus 正，加号sampling 抽查minus 负，减号total inspection 全检disperse 不变，颠簸visual inspection 目视查抄unstable 不稳固appearance check 外不雅查抄balance 均衡patrol 巡检process capability /CP 工程能力measurement 丈量仪三角螺丝刀detection 检验测定measurement 张良，标定check point 查验（重）点measuring method 丈量要领no check 漏检clogging 刻度，分度special adoption application 特采审请memory 储存，影像provisional countermeasure 暂定对策three-dimensional measuring machine 3D丈量仪permanent countermeasure 长久对策microscope 东西目镜claim 投诉，抱怨，索赔profile projectior 投影机appraisal 评价slide calipers 卡尺decide 鉴定micrometer 量具，检查基准check standard 查抄基准lever type dial test 百分表检查基准表inspection sheet 查抄基准表torque gauge 扭转力计QC 工程表QC flow chart QC工程表scale 刻度尺specula face 镜面square 90度角尺mirror face 光面，光泽面steel tate 皮尺texture face 蚀纹面height gauge 高度尺first the face 一级面pin gauge 柱规appearance 外不雅面thickness gauge 片appearance part 外不雅产物protractor 角度仪function part 性能部品tension gauge 拉力机slide 滑动面indicator 百分表检查基准表flatness 最简单的面度hardness tester 硬度计reform 矫正multitester 万用表check jig 查抄用治具surface plate 平台，平板feed back 反馈V block V形块communication 信息，抱怨gauge block 方块规manual 指南，手册dial gauge 百分表flow chart 流程图data 数值process inspection 工程监查data sheet 数值单qualification 确定地认为parameter 参量graph 图表，曲线图warehouse 堆customhouse 海关pallet 卡板customs clearance 报关，通关corrugated fiberboard 纸箱customs clearance 报关手续partition 刀卡electronic data interchange 电子报关recycle box 周转箱container 货柜车plastics box 折叠式周转箱foot 英尺container 份子化合物塑料周转箱packing list 装箱单poly-bag 胶袋list 详细登记单tape 封箱品牌一字螺丝刀胶纸declaration 申请报告rope 绳索，线import 入口first in first out 先入先出export 出口fork lift 铲车fumigation certificate 熏蒸证实书hand lift 手推铲车no wood packing certificate 无木质包装证实书bogie 台车wooden box 木箱truck 卡车shelf 货架license 批文，容许stock 在库数license document 转厂shelf 盘货limits 指标，配额指标dead stock 死仓储，积压品import limits 入口指标purchasing 采集购买unbalance 数目不服衡supply parts 支给品contract 合约purchase parts 采集购买品contract 手册lead time 交货期，定货期order placement 发定单"transfer,carry over" 转余料，拨余料pay 有偿erase 核销free of charge 没有报酬的provision of information 加签vender 供应商submit document 递单quotation 报价单brand name 商物品名称invoice 发票，请款单goods No 商品编码deposit 预付款，包管金foreign enterprise 外资企业payment 付款owned enterprise 独资企业payment condition 付款partnership enterprise 合资工厂month payment 月结processing 来料加工over time 加班（没事了事情日加班）bailment processing 委托加工over time fee 加班费labor cost 人件费holiday work 加班（节假日上班）amortization 折旧费two shift 两班制hour charge 加工费，工时费day shift 白班exchange rate 汇价night shift 晚班material certificate 质料证实书。
注塑常用术语英文表达
1.雾气Moisture Streaks2.玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4.银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7.黑点Dark Sport8.顶出印Visible Ejector Marks9.变形Deformation During Demolding10.填充不足Short Filling11.冷料流痕Cold Slug12.进胶口点不良Dull Spots Near The Sprue13.喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16.过热变色Burnt Streaks17.龟裂Stress Crack18.缩水痕Sink Marks19.真空气泡Density Bubble20.披锋Flash21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine。
完整的注塑专用英语大全-专用技术术语 注塑人必备
Surface Appearance 外观Glossiness/gloss finish 光洁度、粗糙度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on thesurface 玻纤外露、浮纤Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹、料花Flow mark 流纹，流痕Brittle/brittleness 脆、脆性Bubbles/trapped gas 气泡/困气V oid 孔、气泡Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃等级V-2Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 颗粒料孔隙、Low impact/tensile strength etc 低冲击强度/拉伸强度等High flow/filler content etc 高流动性/过度填充Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 纤维结团Product was rejected due to 产品不能接受因为…High moisture level 高水分、高湿度Warpage/warped 翘曲/变形Shrinkage/shrink 收缩/收缩率Sink marks 凹陷、缩水Short shot/short molding 打不满、欠注、缺料，短射Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边、披锋、溢边Discoloration 变色Off color 颜色差异Flow rate 流动速率Viscous/viscosity 粘性的、粘的/黏度High flow 高流动Low flow 低流动Sticky 粘的，粘性的Sticking core 粘后模，粘模芯Sticking sprue 粘水口Sticking cavity 粘前模Mold release（agent）脱模(剂)Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra …添加多一点…Reduced …content 减少…含量Dropped/reduced …by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by …预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量模具方面：Ejection system 顶出系统、脱模系统pin 顶针、推杆spring 弹簧Gate type 浇口类型sprue 主流道runner 分流道cavity 模腔Sprue gate 直浇口Pin point gate 点浇口Tab gate 护耳浇口Fan gate 扇形浇口Tunnel or submarine gate 潜伏式浇口Jump gate 跳跃式浇口Diaphragm gate 片状浇口Ring gate 环形浇口The cavity of the mould 模腔Heated cylinder 加热料筒Surface finish 表面光洁度Sink mark 缩水Air trap 困气Gas trapped 气体困着，困气void 空隙，孔galling 烧焦Weld line 熔接痕，熔合线Drag mark 划伤、脱模痕Scratch mark 模具刮花Deformed/ warp 变形Ejector not returned 顶针不回位slide 滑块、行位streak 波纹、条纹、色痕delamination 分层Jetting mark 喷射痕Gate mark 浇口痕rib 筋、加强筋、骨位boss 凸台、凸起、凸痕Melt flow length 熔体流线长度Ejector plate 顶针板Stop pin 限位销Push rod 推杆、顶针Push back pin 复位杆Ejector guide pin 顶针导柱Cold-slug-well 冷料井、冷料穴plate 模板Ejected mark 顶痕，顶白nozzle 喷嘴Surface defect 表面缺陷Air vent 排气口Filling uneven 走胶不平衡、进胶不平衡。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
1。
雾气Moisture Streaks
2。
玻纤分配不均Glass Fiber Streaks
3.困气Gas Trap Effect
4。
银丝纹Sliver Marks
5.结合线Weld Line
6.水波痕Water Wave Effect
7。
黑点Dark Sport
8。
顶出印Visible Ejector Marks
9。
变形Deformation During Demolding
10.填充不足Short Filling
11。
冷料流痕Cold Slug
12。
进胶口点不良Dull Spots Near The Sprue
13。
喷射痕Jetting
14。
表面起层Flaking Of The Surface Layer
15。
浮泡Entrapped Air
16。
过热变色Burnt Streaks
17。
龟裂Stress Crack
18.缩水痕Sink Marks
19。
真空气泡Density Bubble
20.披锋Flash
21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface
22 尺寸过大Over dimension
23尺寸过小Under dimension
24 翘曲Warpage/warped
25 收缩Shrinkage/shrink
26 缩影Sink marks
27 打不满Short shot/short molding
塑料模具mould of plastics
注塑模具injection mould
冲压模具die
模架mould base
定模座板Top clamping plate
Top plate
Fixed clamp plate
水口推板stripper plate
A板A plate
B板B plate
支承板support plate
方铁spacer plate
底针板ejector plate
面针板ejector retainer plate
回针Return pin
导柱Guide pin
有托导套Shoulder Guide bush
直导套Straight Guide bush
动模座板Bottom clamp plate
Moving clamp plate
基准线datum line
基准面datum plan
型芯固定板core-retainer plate
凸模固定板punch—retainer plate
顶针ejector pin
单腔模具single cavity mould
多腔模具multi—cavity mould
多浇口multi—gating
浇口gate
缺料starving
排气breathing
光泽gloss
合模力mould clamping force
锁模力mould locking force
挤出extrusion
开裂crack
循环时间cycle time
老化aging
螺杆screw
麻点pit
嵌件insert
活动镶件movable insert
起垩chalking
浇注系统feed system
主流道sprue
分流道runner
浇口gate
直浇口direct gate ，sprue gate
轮辐浇口spoke gate ，spider gate
点浇口pin-point gate
测浇口edge gate
潜伏浇口submarine gate ，tunnel gate 料穴cold-slug well
浇口套sprue bush
流道板runner plate
排飞槽vent
分型线(面）parting line
定模stationary mould，Fixed mould
动模movable mould，movable half
上模upper mould，upper half
下模lower mould，lower half
型腔cavity
凹模cavity plate，cavity block
拼块split
定位销dowel
定位销孔dowel hole
型芯core
斜销angle pin, finger cam
滑块slide
滑块导板slide guide strip
楔紧块heel block，wedge lock
拉料杆sprue puller
定位环locating ring
冷却通cooling channel
脱模斜度draft
滑动型芯slide core
螺纹型芯threaded core
热流道模具hot—runner mould
绝热流道模insulated runner mould
熔合纹weld line （flow line)
三板式模具three plate mould
脱模ejection
换模腔模具interchangeable cavity mould
脱模剂release agent
注射能力shot capacity
注射速率injection rate
注射压力injection pressure
差色剂colorant
保压时间holdup time
闭模时间closing time
定型装置sizing system
阴模female mould，cavity block
阳模male mould
电加工设备Electron Discharge Machining
数控加工中心CNC machine center
万能铁床Universal milling machine
卧式刨床Horizontal planer
车床Engine lathe
平面磨床Surface grinding machine
去磁机Demagnetization machine
万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller
超声波清洗机Ultrasonic clearing machine。