X飞机结构设计规范
合集下载
相关主题
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
TABLE OF CONTENTS
PART 1: HEADING.......................................................................................................................................9 1 INTRODUCTION ......................................................................................................................................11 1.1 SCOPE OF THE DOCUMENT ........................................................................................................... 11 1.2 CONTENTS.......................................................................................................................................... 12 1.3 APPLICABILITY / CONFIDENTIALITY...........................................................................................12 1.4 REVISION.............................................................................................................................................13 PART 2: COMPOSITE DESIGN PRINCIPLES ......................................................................................16 1 INTRODUCTION ......................................................................................................................................17 1.1 GENERAL............................................................................................................................................ 17 1.1.1 Highlight.........................................................................................................................................17 1.2 REFERENCES ..................................................................................................................................... 18 1.3 PARTICIPANTS............................................................................................................. ......................19 1.4 REQUIREMENTS TERMINOLOGY................... ...............................................................................20 1.5 ABBREVIATIONS ......................................................................... .............. ..................................... 21 2 DESIGN PRINCIPLES ..............................................................................................................................22 2.1 MATERIALS ...................................................................................................................... ................. 22 2.2 INTEGRATION METHODS................................................................................................ ................22 2.2.1 Co-curing............................................................................................................ ............................22 2.2.2 Co-bonding .....................................................................................................................................22 2.2.3 Secondary bonding................................................................................................. ........................22 2.2.4 Stitching.................................................................................................................... ......................23 2.3 RULES FOR LAMINATE.................................................................................................................... 24 2.3.1 General................................................................................................................... ........................24 2.3.2 Solid laminate......................................................................................................... ........................24 2.3.3 Sandwich.................................................................................................................. .......................39 2.4 TOLERANCES ..................................................................................................................................... 43 2.4.1 Thickness tolerance.................................................................................................. .......................43 2.4.2 Fibre location and orientation tolerances........................................................ ..............................43 2.4.3 Positional tolerance........................................................................................ ................................44 2.4.4 Surface finish.................................................................................................... ..............................44 2.5 JOINTS........................................................................................................................... ...................... 46 2.5.1 Bonded joints.................................................................................................... ..............................46 2.5.2 Mechanically fastened joints.........................................................................wenku.baidu.com... .............................46 2.5.3 Hybrid Metallic-Composite joints..................................................................... .............................53 2.5.4 Torque ............................................................................................................... .............................54 2.6 SHIMMING..................................................................................................................... ......................54 2.7 BEARING AND BUSHING INSTALLATION .................................................................................. 54 3 SPECIAL DESIGNS...................................................................................................................................55 3.1 STRINGERS AND STIFFENERS.........................................................................................................55 3.1.1 Introduction.....................................................................................................................................55 3.1.2 Design Principles ...........................................................................................................................56 3.2 FITTINGS ............................................................................................................................................ 58 3.3 HOISTING POINTS............................................................................................................................. 58 3.4 STIFFENING SWAGES ...................................................................................................................... 58
PART 1: HEADING.......................................................................................................................................9 1 INTRODUCTION ......................................................................................................................................11 1.1 SCOPE OF THE DOCUMENT ........................................................................................................... 11 1.2 CONTENTS.......................................................................................................................................... 12 1.3 APPLICABILITY / CONFIDENTIALITY...........................................................................................12 1.4 REVISION.............................................................................................................................................13 PART 2: COMPOSITE DESIGN PRINCIPLES ......................................................................................16 1 INTRODUCTION ......................................................................................................................................17 1.1 GENERAL............................................................................................................................................ 17 1.1.1 Highlight.........................................................................................................................................17 1.2 REFERENCES ..................................................................................................................................... 18 1.3 PARTICIPANTS............................................................................................................. ......................19 1.4 REQUIREMENTS TERMINOLOGY................... ...............................................................................20 1.5 ABBREVIATIONS ......................................................................... .............. ..................................... 21 2 DESIGN PRINCIPLES ..............................................................................................................................22 2.1 MATERIALS ...................................................................................................................... ................. 22 2.2 INTEGRATION METHODS................................................................................................ ................22 2.2.1 Co-curing............................................................................................................ ............................22 2.2.2 Co-bonding .....................................................................................................................................22 2.2.3 Secondary bonding................................................................................................. ........................22 2.2.4 Stitching.................................................................................................................... ......................23 2.3 RULES FOR LAMINATE.................................................................................................................... 24 2.3.1 General................................................................................................................... ........................24 2.3.2 Solid laminate......................................................................................................... ........................24 2.3.3 Sandwich.................................................................................................................. .......................39 2.4 TOLERANCES ..................................................................................................................................... 43 2.4.1 Thickness tolerance.................................................................................................. .......................43 2.4.2 Fibre location and orientation tolerances........................................................ ..............................43 2.4.3 Positional tolerance........................................................................................ ................................44 2.4.4 Surface finish.................................................................................................... ..............................44 2.5 JOINTS........................................................................................................................... ...................... 46 2.5.1 Bonded joints.................................................................................................... ..............................46 2.5.2 Mechanically fastened joints.........................................................................wenku.baidu.com... .............................46 2.5.3 Hybrid Metallic-Composite joints..................................................................... .............................53 2.5.4 Torque ............................................................................................................... .............................54 2.6 SHIMMING..................................................................................................................... ......................54 2.7 BEARING AND BUSHING INSTALLATION .................................................................................. 54 3 SPECIAL DESIGNS...................................................................................................................................55 3.1 STRINGERS AND STIFFENERS.........................................................................................................55 3.1.1 Introduction.....................................................................................................................................55 3.1.2 Design Principles ...........................................................................................................................56 3.2 FITTINGS ............................................................................................................................................ 58 3.3 HOISTING POINTS............................................................................................................................. 58 3.4 STIFFENING SWAGES ...................................................................................................................... 58