模具常用名称中英文对应表
模具名称中英文对照
行位导向键 = Slider Certer Rail
行位镶件 = Slider Insert
斜边 = Angular Pin
方斜边 = Angular Cam
铲鸡 = Locking Block
行位压板 = Slider Guide Rail
进入位 = gate location
水口形式 = gate type
大水口 = edge gate
细水口 = pin-point gate
水口大小 = gate size
转水口 = switching runner/gate
唧嘴口直径 = sprue diameter
直身杯司 = Straight Bushing
有托杯司 = Shoulder Bushing
方定位块 = Position Block Set
定= Parting Lock
中托司套 = Ejector Lead Bushing
拉杆 = Support Pin
拉杆定位介子 = Support Pin Spacer
齿轮 = Gear
丝杆 = Screw
轴承 = Bearing
油缸 = Oil Cylinder
气缸 = Air Cylinder
间隔圈 = Spacer Ring
垃圾钉 = Slopper Ring
二板模 = 2-plate mold
边钉/导边 = leader pin/guide pin
边司/导套 = bushing/guide bushing
中托司 = shoulder guide bushing
常用模具零件中英文对照表
常用模具零件中英文对照表2005-12-19 14:51:17中国注塑网一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catchFor personal use only in study and research; not for commercial use喉塞:pipeplug锁模块：lockplate斜顶：anglefrompinFor personal use only in study and research; not for commercial use斜顶杆：angleejectorrod尼龙拉勾：partinglocks活动臂：leverarm复位键、提前回杆：earlyreturnbar气阀：valves斜导边：anglepin术语：terms承压平面平衡：partingsurfacesupportbalance模排气：partinglineventing回针碰料位：returnpinandcavityinterference模总高超出啤机规格：moldbaseshuthight顶针碰运水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate.不准用镶件：Donotuse(core/cavity)insert用铍铜做镶件：useberylliumcopperinsert初步（正式）模图设计：preliinary(final)molddesign反呵：reversecore弹弓压缩量：springcompressedlength稳定性好：goodstability,stable强度不够：insufficientrigidity均匀冷却：evencooling扣模：sticking热膨胀：theroexpansion公差：tolorance铜公(电极）：copperelectrode塑件模具相关英文词汇出处：FanE『翻译中国』作者：(转载) FanE『翻译中国』2005-12-16 20:41:59compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型、射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat 浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spearhead刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line 熔合痕eject pin顶出针零件英语punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块14. electrical discharge machining (EDM) 电火花加工15. electrical insulating property 电绝缘性能16. electrochemical die-sinking machine 电解型腔加工机，电解型腔加工机床17. electrochemical machine (ECM) 电解加工机床，电化学加工机床18. electrochemical machining (ECM) 电解加工，电化学加工19. electro-discharge cutting 电火花加工，电火花切割20. electro-discharge cutting machine 电火花切割机21. electro-discharge machine tool 电火花加工机床22. Electro-discharge Machine 电火花加工机床23. electro-discharge machining 电火花加工24. electro-discharge machining process 电火花加工工艺，电火花加工工序25. epoxy resin 环氧树脂9. guide bushing 导套10. guide pillar 导柱，导杆，导柱11. guide pin 导向销，导杆12. guide pin cover 导柱盖13. guide plate 导料板，导板14. guide plate blanking die 导板式冲裁模，导板式落料模15. guide post 导柱，导柱16. guide stock plate 挡料板4. injection mold 注射模，注塑模5. injection molding 注射成型，注塑成型6. injection-molding machine 注塑机，注射机，注塑成形机7. injection plunger 注射柱塞8. in-line reciprocating screw 联机往复螺杆，串联往复螺杆，直线排列往复螺杆9. inner ram 内滑块10. inserting molding 嵌件成形11. integrated manufacturing 集成制造12. internal stress 内应力13. intermediate platen 中间板，隔板塑料成型模具的主要设计要素脱模距stripper distance脱模斜度draft投影面积projected area最大开距maximum daylight;open daylight闭合高度mould-shut height抽芯距core-pulling distance抽芯力core-pulling force脱模力ejector force开模力mould opening force模内压力internal mould pressure;cavity pressure成型压力moulding pressure背压环back-up ring1 bar = 14.5psi高压接头bite type fitting液压马达hydraulic motor冷却水流量计waterflow regulator打磨器材abrasive material打磨砂轮grinding wheels切割砂轮cutting wheels码模夹(注塑机使用) mould clamps; lifting clamps小五金工具piping tools高压力软管high pressure hose风管,水软管air .water hose高压油表pressure gauge压力油喉hydraulic hoses光塑检测photoelastic testing吹塑模plastic blow mould注塑模plastic injection mould冲扎复合模blank & form compound die精密冲模precision blanking die熔料流动率MFR=melt flow rate熔料流动指数MET=melt flow index推板导柱guide pin for ejector plater座板clamping plate垫块space block(plate)推板ejector block(plate)afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件stage ejector 顶棍spacer rock(risers) 间隔板变形distortion弯曲warp拖花drag marks火花纹EDM marks困气venting烧黑burns表面缩水shrinkage料位过薄/砸穿thin wall stock走水不平行uneven fill pattern夹水纹/流纹witness line;mismatch;stress marks 走水纹knit lines走水不齐short shotsorifice 料口nozzle seat 热嘴垫圈nozzle plate 射嘴板cross pin 十字头销sled 射台seal ring 封密圈spacer rail 介子座heater groove 发热管槽heater cement 发热管的结合剂soak 浸泡seat 垫圈ream 铰大圆孔直径grind 磨床drill 钻床mill 铣床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚计hardness tester 硬度计angle gauge 角规marble table 云台石projector 投影仪height gauge 高度仪microscope 显微镜plug gauge 塞规leveller 水平器R gauge R 规Inter caliper 内分厘卡surface 平面仪item number 细目编码catalog number 材料分类编码undercut lip 倒扣口hot tip = hot drop = nozzle 热嘴blow-off strip 放气板blow-off nozzle 吹风口spiral hose 螺旋式的连接喉rust solvent 除锈剂shaft 曲轴tensile strength 拉伸力yield strength 屈服力spark erosion 电火花蚀刻etch(photo-etch) 电蚀harden 淬硬copper electrode 铜公corrosion resistance 耐腐蚀anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域reverse taper 倒啤把clamp plate 码板toggle clamp 快速夹vacuum furnace 真空炉cavity insert rounds 圆柱镶件cavity insert b0locks 方柱镶件tensile strength 抗张强度,抗拉强度Concept drawing 概念图Assembly drawing 装配图mismatch;witness line 夹纹shut-off(n.) 枕位venting valves 疏气阀venting plug 疏气塞valve casing 阀门罩twist drill 旋钻harden/nitride 碎硬anneal 退火temper 回火stess crack 应力断裂corrosion resistance 防腐,防锈tensile strength 物】抗张强度,抗拉强度split mould (分离)组合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,机械等)夹住东西的部分,钳口step change of the P/L 分形面枕位的改变thin steel section 较薄的料位clean-up 清理,清除,清扫Mold Dating Insert 模具日志镶件Hot Sprue Bushing 热浇口套semi-automatic 半自动quick disconnector 快速断开接头full shot 足量注射mismatch 夹痕;夹水纹ejector mark 顶痕screw boss 螺丝孔,螺丝基座sink mark 缩坑15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂drag mark 拖痕stress mark 应力痕reinforcement rib 加强筋slght stoning 轻度磨砂soliid line 实线dotted line 虚线internal diameter 内径external diameter 外径nickel-plated 电镀的handling hole;lifting hole 吊装孔parallel 平行块piston 活塞plunger 柱塞carrier 导轨rest 支架item number 项目编号catalog item 商品目录编码dimensional datum 尺寸基准heat treatment certification 淬硬证明文件back-up bushing 支撑导套jacking screw 起重螺丝,千斤顶tapped hole (带有螺旋角度的)螺丝孔diagonal corner 成对角的角落burn mark 烧痕hot runner mainfold (热流道板)分流板texuring 蚀纹clamping screw (注塑机)码模螺丝imperial 英制的metric 公制的puller bushing 水口套puller bar 水口铁drool bushing 防漏胶套筒safety switch 限位制water line connected internally or hard tubing 不可用胶喉连接运水lifter on square rod or locked from rotation 用方形柱或用管钉止转gate insert 入水镶件gate shut-offs 流道开关配件guided ejection 中托司parting line shutoff 前后模接触面waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱. BGV=Balanced Gate Value 平衡入水值spacer 垫块pocket 挖槽rough 粗加工finish 精加工plunge rate 进刀率retract rate 提刀速率splindle rate 主轴转速coolant 冷却液SPLIT RING 开口环(钥匙圈)侧向抽芯力side pulling-core forceconvert.transfer 转图guide pin 边针Tee slot cutter T形SLOT CUTTERzigzag 双向切削constant overlap spiral 等距环切parallel spiral 环绕切削parallel spiral clean corners 环切并清角morph spiral 依外形环绕true spiral 螺旋切削one way 单向end mill 平铣刀spher mill 球刀bull mill 圆鼻刀face mill 面铣刀rad mill 圆角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔铣刀dove mill 鸠尾铣刀lot mill 棒状drill 钻孔reamer 纹刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心钻spot drill 点钻cntr bore 沉头孔刀c. sink 鱼眼孔钻loft surface 举升曲面coons surface 昆氏曲面ruled surface 直纹曲面revolved surface 旋转曲面swept surface 扫描曲面draft surface 牵引曲面grinding wheel 磨砂使用的轮子quench steel 将...淬火,使冷却stress relieving 应力消除molten 熔热的oxide film 氧化层guide pin and sleeve, locating ring ,导边,司筒,定位圈ejector ,ejector balde, ejector sleeve,顶针,扁顶针,顶针司筒, lifters, wear plate,horn pin,斜坊,磨损板,气顶针,O ring, water baffle, water pipe plug,O形圈,隔片,运水管道塞, water line connector,wear plate ,运水管道转接头,耐磨板air cylinder,hydraulic cylinder,氯压缸,液压缸micro switch,oil nipple, spring,开关装置,油枪接头,弹弓sprue bushing,early return system,浇口套,早期回撞装置, accelerated ejectors, slied holder,加速顶针,注塑周期计数器, cycle counter,date stamper，滑块固定板,生产日期铭牌,hot runner system ，热流道系统chemical composition 化学成份thermal conductiivity 导热性能thermal diffusivity 热扩散性能dimensonal stablity 尺寸稳定性能cooling effiency 冷却效率easiler ejection 易于脱模alloy insert 合金镶件(cooling) duct 输送管;导管maintenance cost 维护费用ultrasonic testing 超声波检测crack 断裂direct gate 直接浇口ring gate 环形浇口disk gate;disphragm gate 盘形浇口spoke gate;spider gate 轮辐浇口pin-point gate 点浇口edge gate 侧浇口submarine gate;tunnel gate 潜伏浇口fan gate 扇形浇口tab gate 护耳浇口runner plate 流道板(或冷或热)secondary nozzle 二级喷嘴torpedo;torpedo body assembly 鱼雷形组合体catridge heater 管式加热器heat pipe 热管valve gate 阀式浇口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活动镶件cavity splits;core splits(凹模拼块) (型芯拼块) 拼块side core 侧型芯thread plug;threaded core 螺纹型芯thread ring;threaded cavity 螺纹型环cutting wheel 切割砂轮grinding wheel 打磨砂轮abrasive material 打磨器材mould clamps;lifting clamp 砂模夹(注塑机使用) air (water) hose 风管,水轮管pressure gauge 高压油表hydraulic hose 压力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 冲扎复合模precisiion blanking die 精密冲模MFR=melt flow rate 熔料流动率MFT=melt flow index 熔料流动指数handling hole 拉铃孔stop plate 限位块linder bush 衬套spacer block(plate) 垫块,方铁back-up ring 背位环standoff 限位块American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能Tensile Strength(MPa) 抗拉强度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 冲韧性Physical Properties 物理性能solidification shrinkage 凝固收缩率freezing range 凝固与熔范围thermal expansion 热膨胀系数specific heat 比热thermal conductivity 热导率electrical conductivity 电导率micro-structure 金相分析hot work tool steel 热作钢circular motion 环形运动variable 变数,参数graphics window 图形窗口45 degree entry and a zero degree exit. 进刀口45度,退刀口0度runner stripper plate 脱料板stripper plate 活动板spacer rock(risers) 间隔板stage ejector 顶棍sprue puller insert 扣针导套guide strip 行位后板afdek plate 挡尘板side gate 大水口pinpoint gate 细水口SHCS 杯头螺丝FHCS 平头螺丝set screw 无头螺丝ball catch 波子螺丝wedge 行位较杯gib 线条,(撑鸡的导轨)latch 拉杆clamp 码仔spring guide pin 弹弓导柱steel pad disc 橙仔方ejector cam insert 斜顶块(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把锁texture 花纹toggle-lok 回撞装置top clamping plate 顶码板unified national coarse (UNC) 美制螺丝(粗牙) unified national fine (UNF) 美制螺丝(幼牙) set screw 喷头螺丝side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 弹弓座sprue puller 勾针/勾粒spring washer 弹簧塑圈stepped ejector pin 有托顶针strippers plate 推板/细水口板submarine gate 潜水口support pin 拉杆support plate 暗板surface finish 光洁度alignment strip 斜锁angle pin 斜针fan gate 扇形入水fillet 圆口ball catch 弹弓波子blade ejector 扁顶bottom clamping plate 底码板free length 自然长度bridge piece 水口铁helix spindle 锅杆hose clip 水喉箍bubbler 隔气运水jiggle 斜顶jiggle witness line 斜顶片位置center distance (CRS) 山打距离(中心线距离)clamp 码仔contour 外形leader pin 导针location ring(flange) 法兰counterbore 拔头,介子托mock-up;prototype 手办die cast 合金压铸national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,顶套epoxy 胶样pin point gate 细水口pressure plug 喉塞pressure spring 压力弹簧parting line flash 披锋burned 烧黑underfilled 缺料insert mismatch 镶件夹口ejector pins not flush 顶针有高低ejector pins skid 顶针滑动insert flash 镶件披锋pressure transducer 压力探测头hydraulic schematic 油积筒油路接驳图jiffy connector recessed 安装喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位开关stop block 限位块safety strap 安全带drool bushing 防漏胶套筒insert mismatch 镶件夹口EDM visible 明显火花纹lifter scrapes 斜顶拖花short shots 走水不齐wall stock 料位厚薄knit lines 走水纹stress marks 夹水纹uneven fill pattern 走水不平行drag marks 拖花sprue pretrusion 唧嘴突出高度sprue orifice and radil size 唧嘴R尺寸sprue bushing-keyed 唧嘴有管钉English Chineseprogram name 产口名称part name 零件名称tool name 模具名称tool source 模具来源tool steel 模具钢材resin 塑料program number 产品编号part number 零件编号tool number 模具编号customer 客户名称No of cavities 内模编号machine size 啤机吨数drum miller 鼓形铣床duplex horizontal miller 复式卧铣床face miller 端面铣床grinding miller 研磨机plain miller 平面铣床planer-type miller 刨式铣床rack miller 齿条铣床slab miller 大型平面铣床slot miller 键槽铣刀spline miller 花键铣刀thread miller 螺纹铣刀vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀plastic mould steel 塑料模钢cold work steel 冷作钢hot work steel 热作钢high speed steel 高速钢electric magnetic clutch 电磁离合器pad printer 移印机screen printer 丝印机hot stamper 烫印机solid carbide slitting saw 钻石钢锯片convex cutter 凸锣刀片concave cutter 凹锣刀片side&face cutters,staggered teeth 正侧双用镶钻石钢锣刀end-mill 锣刀semi-rod 半圆刀split double end 双头刀single end 单头刀2-flute 两辨3-flute 三辨4-flute 四辨reamer 直拈centre drill 中心钻solid carbide drill 钻咀zinc ingot 锌锭aluminium ignot 铝锭tin ignot 锡锭heater cement 发热管的结合剂heater groove 发热管槽spacer rail 介子座cross pin 十字头销nozzle plate 射嘴板nozzle seat 热嘴addendum 齿冠dedendum 齿根air compressor 空气压缩机air exhauster 抽气机air intake 进气口air seal 空气隔离层仅供个人用于学习、研究；不得用于商业用途。
模具中英文对照
搬运固定板 防呆装置 快速定位 安全侧销 保管垫块 平衡垫块 停止垫块 氮气缸 到底记号 镶块 素材定位器 进退料支架 脱料板 顶料块 下模钢块 行程定位具 废料刀 废料盒 废料滑槽 折边刀块 定位键 凸轮组件 凸轮滑动座 凸轮驱动座 凸轮侧滑块 切刀块 分块 导柱 导套 导柱组 缓冲垫块 挡板（块） 垫块 垫圈 固定块 作用套管 安全套管 滚轮（组） 优力胶 弹簧 卸模停止具 侧销 H型顶料机构 UPPER DIE UPPER DIE HOLDER LOWER DIE LOWER DIE BOTTOM HOLDER DIE PAD SAFETY GUARD WEARPLATE HOOK INSERT HOOK FIX IN PLATES FOOL PROOFING QUICK CLAMP RETAINER PIN SETS(SAFETY) BLOCKS BALANCER BLOCK STOPER BLOCK NIIROGEN SPRING CHECK BUTTONS INSERT BLOCK NEST GUIDE SKID BRACKETS STRIPPER DIE LIFT BLOCK LOWER STEEL STROKE END BLOCK SCRAP CUTTER SCRAP BOX RETAINER BOLT FLANGE DIE LOCATING KEYS CAM UNIT CAM SLIDE CAM DRIVER CAM SIDE SLIDE CUTTER BLOCK SECTIONAL BLOCK GUIDE POST GUIDE BUSH GUIDE POST SET CUSHION PLATE BAFFLE PLATE WASHER FIXED PLATE SPOOL RETAINER SAFE STOPER BOLT RUBBER ROLLER(ASSEMBLY) STOCK BLOCKS COIL SPRING UNLOAD DIE STOPER BLOCK SIDE PIN H LIFTER UNIT 零件详细 检具 气缸 接头 C式快速接头 三向接头 万向接头 L型快速接头 T型快速接头 阀 调速阀 方向控制阀 定位销 开口销 带头销 固定销 夹 管 连接管 通气管 PVC管 行程端管 轴 连杆轴 焊接 树脂 消音器 螺帽 有槽螺帽 销规 冲母座 承盘 柱塞 端子箱 集头座 内六角螺栓 内螺纹圆柱销 吊挂 弹簧导销 工法图 上模平面 下模平面 断面 冲头 衬套 冲头固定座 盖板 垫板 打料器 托架 柄 曲柄 下料排样图 PARTS DETAIL CHECKING FIXTURE CYLINDER ADAPTER(AUGMTURE) QUICK NIPPLE THREE-WAY CONNECTOR UNIVERSAL-JOINT ADAPTER L JOINT T JOINT VALVE COVERNOR VALVE DIERCTIONAL CONTROL VALYE LOCATION PIN SPLIT PIN PIN WITH HEAD DOWEEL PIN CLAMP PIPE CONNECTOR AIR VENT AIR TUBE STROKE END PIPES SHAFT LINK SHAFT WELDING RESIN MUFFLE NUT SLOTTED NUT GUAGE BUSH(BUTTON DIE) RETAINER PLUNGER CABLE CONNECTING BOX CONNERTOR SUPPORT S.H.C.SCREW DOWEL PIN RETAINER BOLT SPRING GUIDE RETAINERS DIE LAYOUT ,PROCESS SHEETS UPPER DIE OF PLAN VIEW LOWER DIE OF PLAN VIEW SECTION PUNCH BUTTON RETAINER SAFETY GUARD BACKING PLATE KNOCK OUT PIN BRACKET HANDEL CRANK STRIP LAYOUT OF BLOCK
模具常用名称中英文对照表
24. 电极：Electrode——缩写：Elc
25. 限位：LIMIT——缩写：LT
26. 导向板：GUIDE PLATE——缩写GUP
27. 直顶块： STRAIGHT EJ BLOCK——缩写STB
28. 补强板： STIFFENING PLATE——缩写STP
5. 热流道板(热浇道板)：Hot runer——缩写：HR
6. 母模（定模）：Cavity——缩写：Cav
7. 导柱：Guide Pin——缩写：G.P.
8. 导套：Guide bush——缩写：G.B.
9. 复位杆：Release Pin——缩写：R.P.
10. 动模型芯（中间体）：Core——缩写：Cor
11. 模脚：Support parallels——缩写：Supa
12. 侧翼块：Side block——缩写：Sibk
13. 轮Leabharlann ：Plin——缩写：Plin 14. 模座（底座）：Die holder——缩写：Dho
15. 镶件：Insert——缩写：Ins
16. 滑块（行位块）：Slide——缩写：Sld
模具数模命名规则及常用名称中英文对照表（含缩写）
1. 射嘴：Nozzle——缩写：Noz
2. 定位圈：locating ring——缩写：locr
3. 浇口套：Sprue bush(Sprue busing) ——缩写：Sprb
4. 垫板(固定板)：Base Plate——缩写：BP
17. 斜顶块：Lifter——缩写：Lit
18. 推板(顶板)：Eject Plate——缩写：EP
模 具 常 用 术 语 中 英 文 对 照 表
中文hot nozzle 来自hermocouple英文
中文
管状管钉 吊环 日期印 环保印 气顶 截水口镶件 早回 加速顶 客户 产品名 产品编号 缩水 版本 型腔数 模号 胶料 尺寸 重要尺寸 公差 线切割 电火花 抛光 蚀纹 雕刻 出模角 分模面 擦位 倒扣
英文
tubular dowel safety hoist ring dating insert recycling insert air poppet valve runner shut-lff inser early ejector ruturn accelerated ejector client part name part no syr8hiage rev. cav. mold no. material dimension critical dimension tolerance wire-cut EDM polishing texture engrave draft parting surface shut-off(S/O) under-cut
模具常用术语中英文对照表
中文
模胚 上模镶件 下模镶件 小镶件 下模小镶件 上模小镶件 行位 行位镶件 压条 压紧块（铲机） 硬片（摩擦片） 水口铁 上模水口铁 下模水口铁 弹簧 水口勾针 顶针 撑头 直身锁 斜度锁 锁模板 O‘令（密封圈） 喉塞 隔水片
英文
mold base core block cavity block sub-insert cavity sub-insert core sub-insert slide slide insert gib jaw wear plate runner bar upper runner bar lower runner bar spring sprue puller pin ejector pin support pillar side lock inter lock safety bar O'ring plug baffle 热嘴 控热针
模具常用术语中英文对照表
模具常用术语中英文对照表Document serial number【LGGKGB-LGG98YT-LGGT8CB-LGUT-"R，L Co.,Ltd"模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割Wire 轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts指定吨位的注塑机Specific Press 水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin 二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary 名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位Leader Pin Location 耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked 配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin 顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing水口板导套Runner Stripper Plate Bushing定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return 加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert 行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate 水口铁Runner Bar上模水口铁Upper Runner Bar 下模水口铁Lower Runner Bar 弹簧Spring水口勾针Sprue Puller Pin 顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar ‘O’令（密封圈） O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针ShoulderEjector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing水口板导套Runner Stripper Plate Bushing定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return 加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹） Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance 突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven 走不齐Short Shot挂成品Part Hanging 漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold 入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav 名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板 A'plateB板 B'plate倒扣Under-Cut 披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface 擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag 线切割Wire 轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts指定吨位的注塑机Specific Press 水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High Volume RunningMold剖面图Cross Section 模具结构Mold Construction 模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension 雕刻Engrave托司 PIN。
模具结构中英文对照表
中文名英文名中文名日期印Date Code[kəud]司筒基准Datum[deitəm]斜顶垂直Alignment{əlainmənt]回针夹紧Binding[baindiŋ]顶针模腔Cavity(cav)扁顶颜色Color有托顶针外转角Corner[kɔ:nə]/outside中心针详图Detail[di:teil]浮哥出模角度Draft(dft)[drɑ:ft]预压图纸编号Dwg No.气氮/氮化雕字Engrave[in'ɡreiv]液氮内转角Fillet[filit]/Inside Radius火花电蚀光洁度Finish[finiʃ]火花电蚀平凹Flush[flʌʃ]隔热板入水位Gate温度感应器枕位碰穿Kiss-Off热咀商唛Logo油压马达胶料Material(Matl)[mətiəriəl]扣鸡穿孔Opening行位行程产品编号Part No.(P/N)推板凸高Raised[reizd]早回装置参考Reference(Ref)['refrəns]线切割修正Revision(Rev.)[ri'viʒən]导套缩水率Shrinkage['ʃriŋkidʒ]Factor['fæktə]针板导柱擦位Shut[ʃʌt] Off/(S/O)哥针/镶针凹入Recessed[ri'sesid]脱料板皮纹Texture[tekstʃə]热流板产品名称Title['taitl] /Part Name A板公差Tolerance(Tol.)['tɔlərəns]推板类型Typical(Typ.)['tipikəl]B板疏气/排气Venting['ventiŋ]承板倒扣Undercut(U'CUT)['ʌndəkʌt]方铁胶位厚度Wall[wɔ:l] Thickness['θiknis]面针板法兰/定位圈Locating Ring/Fixing Ring底针板唧咀（浇口套）Sprue[spru:] Bushing['buʃiŋ]底板直身锁Side Lock[lɔk]顶板啤把锁/斜度锁Taper['teipə] Lock斜顶滑座喉塞Plug[plʌɡ]斜顶喉咀Jiffy Connector滑动镶件胶圈/胶令/密封圈"O"ring/Seal Ring互换镶件隔水片Baffle铲鸡撑头Support Pillar压条顶棍孔Knockout Hole逼紧块内模玉/内模件Insert耐磨块模具常用名细镶件Sub-insert导向块水口套Runner Bar斜顶导向块运水通Bubbler Tube滑块导轨行位/滑板Slide滑块束块斜边钉Cam Pin斜顶底座垫片/硬片Wear Plate锁模块压锁Jaw青铜线条Gib夹具行位夹Slide Retainer顶棍接头弹弓波珠/弹簧钢珠Ball Plunger吊模板弹弓/弹簧Spring直身导边油唧筒Hydraulic Cylinder有托导边直齿轮Spur Gear直身杯司天梯/齿条Rack有托杯司啤令/轴承Bearing方定位块发热线/炮仗Heater定位锥鱼雷Probe尼龙塞接头Connector中托司套拮制Limit Switch中托导柱导柱Guide Pin/Leader Pin/Guidepillar脱水口螺丝组常用名称中英文对照英文名中文名英文名Ejector Sleeve限位螺丝Stopper BlotAngle Lifter/Lifter限位钉Positioning PinReturn Pin管位块Slotter KeyEjector Pin顶针板Ejector retainer plate Ejector Blade限位块Distance SpacerStepped E.P.无头螺钉Screw PlugCenter Pin平头螺钉Socket Head Cap Screw Floating Core/Plate波子螺丝Ball PlungerPre-loaded定位螺钉Positioning Screw Plrg Nitrided截流塞Cooling Circuit PlugTufftrided回针Return PinEDM拉杆Puller PillarCNC拉杆定位介子Support Pin SpacerInsulated/Insulating plate齿轮GearThermocouple['θɜ:məʊkʌp(ə)l]丝杆/螺丝ScrewHot Nozzle/Bushing轴承BearingHydraulic Motor液压油缸Hydraulic CylinderLatch-lock气缸Air Cylinderslide travel间隔圈Spacer RingStripper Plate垃圾钉Slopper RingEarly Return行位开关组Detection Switch SetWire Cut上模镶针Inlay Cavity PinGuide Pin Bushing流道衬板Runner PlateGuide Ejector(E.G)水口钩针Runner Lock PinCore Pin行位导向键Slide Center RailSpacer Plate行位镶件Slide InsertSpacer Plate方斜边Angular CamA Plate行位压板Slide Guide RailStripper Plate压板Cover PlateB Plate销钉Dowel PinSupport Plate斜边压块Holding Plate For A.P.Spacer Block冷胶Sprue Lock BushingEjector Retainer Plate运水镶件Insert For CoolingEjector plate等高螺丝Stopper BoltBottom Clamp Plate防尘板COVER PLATETop Clamp Plate斜契块WedgeSlide Unit For Loose Core接线盒Electrode BoxANGLE LIFTER顶棍K.O.ROBSlide Insert铍铜BECUChange Insert码模接头Clamp AdapterWedge流道截面RUNNER SECTIONGIB浇口SprueFixing element斜导柱Angle Pin/Slide PinWear Plate缩水印Sink markGuide Block波子弹弓Ball catchLift Guide Block喉塞expander sealing plug Slide Guide吊模条/扁担transport bridgeSlide Wedge吊环eyeboltLift Base强行脱模force demold/force demould Safity Strap青铜块Bronze compactBronzeClampK.O.AdapterEyebolt PlateStraight Leader PinShoulder Leader PinStraight BushingShoulder BushingPosition Block SetTaper Pin SetParting LockEjector LockEjector Leader PinPuller Bolt Set。
模具专业词汇中英文对照表
模具专业词汇中英文对照表1. 模具材料（Mould Materials）•合金钢（Alloy Steel）•不锈钢（Stnless Steel）•工具钢（Tool Steel）•铸造铁（Cast Iron）•铝合金（Aluminum Alloy）•铜合金（Copper Alloy）•硅橡胶（Silicone Rubber）•塑料（Plastic）•陶瓷（Ceramic）2. 模具零件（Mould Components）•模板（Mold Base）•注塑装置（Injection Unit）•顶出器（Ejector）•气嘴（Nozzle）•间隙（Clearance）•提位器（Lifter）•滑块（Slide）•定位圈（Locating Ring）•膜背（Backing Plate）•挡块（Stop Block）•压板（Clamp Plate）•冷却管（Coolant Pipe）•驱动装置（Drive Unit）3. 模具制造工艺（Mould Manufacturing Process）•设计（Design）•切割（Cutting）•加工（Machining）•组装（Assembly）•调试（Debugging）•精修（Finishing）•表面处理（Surface Treatment）•检查（Inspection）•试产（Trial Production）4. 模具加工方式（Mould Processing Methods）•铣削（Milling）•磨削（Grinding）•拉刀（Planing）•镗削（Boring）•钻孔（Drilling）•线切割（Wire Cutting）•抛光（Polishing）•火花加工（EDM）5. 模具设计要点（Key Points in Mold Design）•壁厚（Wall Thickness）•浇注系统（Gating System）•冷却系统（Cooling System）•排气（Venting）•气罩（Bubbler）•顶杆（Ejector Pin）•脱模斜度（Draft Angle）•零件坯料与尺寸（Blank and Dimensions）•对位方式（Alignment Method）•衬套（Insert）•翻制（Flip Mold）•分模（Split Mold）6. 模具维护与保养（Mold Mntenance）•模具清洁（Mold Cleaning）•润滑（Lubrication）•排浆（Purging）•磨损修复（Wear Repr）•抛光修复（Polish Repr）•零件更换（Component Replacement）•修复记录（Repr Record）•数字化管理（Digital Management）7. 模具常见故障及解决方法（Common Mold Faults and Solutions）•翘曲（Warping）•缺陷（Defects）•泛油（Flash）•磨损（Wear）•烧坏（Burning）•掉件（Part Ejection）•插损（Insert Damage）以上仅是模具专业领域常用词汇的一个简单对照表。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
英文名 bleeding blister bubble burned chalking clear patches crack discolouration filler specks fines fisheyes flash frosting haze orange peel pimple pinhole porosity scratch splashing weld line stamping machine transer moulding machine vacuume metallizer
ejector system on coefficient layout guaranteed tool life spare part requested tech point checklist parting line gating point cavity marking date code 12NC marking mould marking sub-contracting item sketch finishing 2 plate mould combined tool
I.P. P.L.
E.G.P. S.B.
W.J.
S.S.L. T.L. A.P. P.K. D.P. T.B.S.
電阻焊接 固定圈 螺絲批 點焊 彈簧夾 彈簧墊圈 雙頭螺栓 轉矩扳鉗 觸針 超聲焊接
resistance welding retaining ring screw driver spot welding spring clips spring washer stud torque wrench welding horn ul accelerator aging back pressure breathing cell-forming agent charge clamping frame compressor cooling fixture de-gassing expanding agent foaming agent gelling glass mat gloss heating element land moulding cycle mould parting line platform polymerization polystyrene beads pre-expand promotor regrind regrind material release agent rotation spindle roving seamless solidify spray gun squeegee steam jacket surge tank transfer chamber vacuume pump vent mould stripping polish grin lathe mill wire cut
中文名 滾壓 離心澆鑄 冷模塑 浸漬模塑 雙色模塑 垂幕式成型 包封,包裝,封裝 發泡模塑 纏絲法 鍛制 嵌件模型 相配模塑 相配模成型 熔體滾筒涂層 膠漿澆鑄 塞杆式真空成型 粉涂層 預混模塑 壓力袋模塑 旋轉模塑，搪膠 增強 膠漿模塑 壓傳涂層 真空袋模塑 真空驟縮成型 網架浸漬 預接待室 鎖模扣 拉針 油坑 薄鋼 模架 噴油 絲印 水路
唧嘴 水口扣針 頂針 頂板 面針板 邊釘 受力單位 受力板 模板 模塊 模鑲件 口哥塊 內口哥鑲件 固定口哥鑲件 活動口哥鑲件 行位,滑動板
sprue bushings butt joint ejector pins ejector plates ejector pin retainer plate loader pins force units force plate cavity plates cavity blocks cavity inserts core blocks core inserts fixed cores moveable cores slides
模具常用名稱中英文對應表 中文名 模胚 模（前模） 口哥（后模） 細水口 大水口 水口板 水口推板 模板 口哥板 面針板 底針板 方鐵（凳仔方） 底板 水口邊（支撐針） 直邊（導柱）/導向針 水口拉 木旱 托司(導套) 直司 回針 唧嘴 熱呶嘴 入水 流道 定位圈（法蘭） 水口鉤針 塞打螺絲 彈弓膠 拉膠 頂針 扁頂針 有托頂針 司筒針 單頭柳釘 平接 電動螺絲批 氣動螺絲批 換能器 焊條 磨擦焊接 氣焊 膠 熱壓封口 搭接 保險螺絲 螺母 英文名 簡稱 Mold Base Cavity Core Pin Point Gate Side gate Top clamp Plate Stripper Plate A Plate B Plate Ejector Retainer Plate Ejector Plate Spacer Block Bottom Clamp Plate Support Pin S.P. Guide Pin G.P. Small Support Pin S.S.P. Shoulder Guide BushSH.G.B. Straight Guide Bush S.G.B. Return Pin R.P. Sprue Bushing SP.B. Hot Sprue Bushing Gate Runner Locating Ring L.R. Runner Lock Pin R.L.P. Puller Bolt C TYPE P.B.C. Rubber Spring R.S. Parting Lock PA.L. Ejector Pin E.J.P. Ejector Blade E.J.B. Stepped Ejector Pin S.E.J.P. Ejector Sleeves E.J.S. blind rivet butt joint screw driver, electric screw driver,pneumatic energy converter filler rod friction welding gas welding glue heat sealing lap joint lock nut/lock washer nut 英文名 Ejector Block Insert 行位 Slide 斜方 Slant 鑲針 Insert Pin 拈板 Clamp Wedge 開模線面 Parting Line 杯頭螺絲 Screws 硬板 Harden Plate 電鑄 Electro-formed 中托邊 Ejector Guide Bushigs 撐頭 Support Block 彈弓 Spring 運水 Cooling 運水膠圈 "0"Ring 運水桶 Cooling Hole 喉嘴 Water Junction 發熱管 Hot Pin 拉令孔 Tapped Hole For Eyebolt 蝴蝶鉸 Butterfly Ware 拉勾(扣基) Multi Lock 指示針 Date Code 字嘜 Indicator 彈弓螺絲 Spring Screw 拉圾釘 Stop Pin 方型輔助器 Straight Side Interlocks 斜邊釘 Taper InterLock 斜導柱 Angular Pin 定位扣 "P" Lock 銷釘 Dowel Pin 斜鎖位 taper Block Set-ky TYPE 中文名 推方 簡稱 E.J.K. 中文名 添加劑 粘結劑 醇酸(樹脂) 抗氧化劑 抗靜電劑 觸媒,催化劑 涂層 著色劑 化合物 硬化劑 填充劑 阻烯劑 起泡劑 層壓料 潤滑劑 單聚物 增強劑 樹脂 溶劑 穩定劑(器) 紫外線吸收劑 超聲波模 螺紋 螺旋形的 倒扣,咬邊 操作表面 鋼公 加工程序 英文名 (')additive adhesive alkyd antioxidant antigtatic agent catalyst coating colorant compound daring agent(hardener) filler flame retardant foaming agent laminated lubricant monomer reinforcing agent resin solvent stabilizer ultraviolet absorber ultrasonic welding thread spiral undercut actuating surface electrode secondary process 中文名 燃燒率 冷流 壓縮強度 開裂應力 蠕變 撓曲溫度 介電常數 介電強度 體積穩定性 彈性模數 伸長 防火 可燃性 彎曲強度 耐熱 沖擊強度 模塑收縮量 戶外風蝕 抗刮磨 抗剪/切變強度 軟化溫度 比重 腫脹 抗撕裂/抗扯強度 抗拉強度 熱傳導性 熱膨脹系數 粘度 翹曲 附針(導柱) 司(導套,套司) 平行板 壓板 墊片 碼板 托板(固定器) 勾針 頂針 頂針板 托板 頂針 頂出條 頂出板 壓條,碼板 英文名 burning rate cold flow 3 compressive strength cracking stress creep deflection temperature dielectric constant dielectric strength dimensional stability elastic moulds elongation flame resistance flammability flexural strength heat resistance impact stregnth mould shrinkage scoutdoor weathering scratch resistance shear strength softening point specific gravity swelling tear resistance tensile strength thermal conductivity thermal expanion coefficient viscosity warpage guide pins guide pin bushings parallels clamping plate pressure pads mounting plates retainers pot plungers pots pot retainers backing plates knockout pins knockout bars knockout pin plates gibs