船舶轮机英语集成
轮机英语词汇总结1~20章
Lesson1：ships and machinery 专业词汇：naval architect造船工程师marine engineer轮机工程师hull 船体外壳propel推进steer 操舵anchor 抛锚cargo-handling 货物装卸vibration振动longitudinal纵向的transverse横向的deck甲板hatch 舱口hatch cover舱盖navigating bridge area 驾驶台communication centre通信中心stabilizer 减摇鳍container ship 集装箱船bulk carrier 散货船tanker液货船passenger ship 客船cruise ship 游船pilot vessel 引航船displacement排水量deadweight 船舶载重量light weight 船舶空船排水量installation 安装layout 布置gearbox 齿轮箱direct-couple 直接传动diesel engine柴油机team turbine 蒸汽轮机propeller 螺旋桨prime mover原动机crankshaft 曲轴cylinder 气缸auxiliary辅助的generator发电机air compressor 空压机evaporator 造水机heat exchanger 换热机boiler 锅炉funnel烟炊twin-screw双螺旋port左旋starboard 右旋waste combustion plant 焚烧炉bulkhead 船舱壁metric米制的公制的tug 拖船非专业词汇：vehicle 交通工具habitability可居住性overlap 重合ores 矿石arbitrary 任意性distinct 清楚的独特的endure 持续度过self-sustaining 自稳定自维持Lesson2：how does a marine diesel engine work 专业词汇：internal combustion engine内燃机ignite 点燃injection喷射chamber腔室piston活塞spray 油雾cycle循环sequence顺序stroke 冲程alternator 交流发电机aspirate吸入atomized 雾化的auxiliary 辅助的blow 吹，鼓风draw 抽吸centripetal 向心的chamber 腔，室charge 填充物combustion 燃烧compress压缩crank 曲柄crankshaft 曲轴crankpin 曲柄箱cylinder 气缸diesel 柴油机exhaust 排出，耗尽，废气fine细小的generator 发电机ignite 点燃induce 引起，招致inefficient 效率低的inhale 吸入inject 喷射injector喷射器inlet 进口marine海运的，船用的piston活塞principle 原理，原则propeller螺旋桨，推进器propulsion 推进residual 残留的，剩余的revolution 转rotate 旋转scavenge扫除，吹除timing 定时turbocharge 涡轮增压turbocharger 涡轮增压器bottom dead centre （BDT）下止点top dead centre（TDC）上止点loop scavenge 回流扫气uniflow scavenge 直流扫气reduction gear box 减速齿轮箱slight ram 进气阀座connecting rod 连杆blade 叶片非专业词汇：adjacent邻近的application 请求，应用closure 关闭encourage 促使fresh 新鲜的inlet 进口medium 中间的，介质operation 操作，过程poppet 提升retard 推迟vast 大量的Lessen3 diesel engine construction 专业词汇：adjustment 调节annular 环形的assembly 组件bearing 轴承bedplate 机座bolt螺栓bore 钻孔channel 通道clearance间隙component 部件diameter 直径dowel 销钉drill 钻孔duct 管道emission 散发，喷射film 油膜flange 法兰forge 锻造frame 机架groove槽，沟guide导板indicator 示功器jacket 夹层joint 接口liner 衬套maneuverability 机动操作性，机动性mount 安装pin 销子reliability 凹槽scraper 刮油器screw 螺钉seating 座，底座shim 垫片shoe 滑块slot 开槽stud 双头螺栓weld焊接carrier ring 承磨环cast iron 铸铁chain transmission 链条传动white metal 白合金stuffing box 填料箱非专业词汇：deformation变形rigid 刚性的，坚实的rubber 橡胶horizontally 水平地adequate 足够的advanced先进的chromium镀铬construction结构displace 错位integral 整体的precise精确的reliability 可靠性rotary旋转secure固定topmost最上部vertical垂直的vital至关重要的Lesson4 fuel oil system 专业词汇：catalyst催化剂catalytic催化剂的centrifuge分油机cavitation 气穴现象contaminate污染contaminate杂质deaerate除气，除氧impurity杂质，混杂物overflow溢流overhaul大修pressurize增压，密封purifier分水机clarifier分杂机refinery炼油厂rust铁锈safeguard维护，保护措施black-out全船停电booster pump增压泵gasway气道in parallel并联in series串联residual fuel渣油fuel oil燃油diesel oil柴油daily service tank日用柜viscosity粘度preheater预热supply pump驳运泵maintenance维护setting point倾点water content水分cleaerate放气flash point闪点specific gravity比重valve seat阀座bar大气压filter滤器非专业词汇：component元件，构件consumption消费量conventional常规的delivery传递，输送provided倘若irrespective不考虑的Lesson5 central cooling water system专业词汇：Chest 箱，柜deaeration除气malfunction故障scoop收集器，吸入口standstill停车thermostatic恒温的by-pass旁通管expansion tank 膨胀水箱volume体积alarm device 报警装置shipyard船厂非专业词汇：Accomodate 收容，装有additional另外的alternatively备用地integrate使成整体，结合Lesson 6Reservoir 容器Drainage 放残Interlock 连锁Non-return vavle 单向阀Pilot air 控制空气Pneumatic 气动Vent 放气Ahead/astern 进车/倒车Deposit 沉积物Ignite 点燃Flame trap 阻焰口Relief vavle 安全阀Bursting cap 防爆门Fusible plug 易熔塞Air distribution 空气分配器Engage/disengage 啮合/脱离Humidity 湿度Suck in 吸收Isolate 隔离Manoeuvre 操纵，机动Provision 备件Reluctant 冗余的Drawn from 来自Stringent 严格的Bore 孔Correspond 相应的Whilst 当什么时候Occurrence 事故Lesson 7Oil film 油膜Neutralize 中和Acidic product 酸性产物Considerable 相当多的Resist oxidation 抗氧化Wear detritus 磨削Total loss system 不回收系统Circulating system 循环系统Line wall 气缸壁Piston ring belt 活塞环带Carry Out 实现完成Quill 注油针阀Residual fule 渣油Corrosive 腐蚀的Lacquer 漆Alkalinity 碱Detergency 去垢能力Property 性质Rupture 破裂Crack 裂纹Slump 油底壳In duplicate 双联Level guage 液位表Drain tank 循环柜Impinge 射到Counteract 克服Impart 给予Reversal 相反的=Lesson 8Naturally aspiration 自然换气Exhaust gas turbocharging 废气涡轮增压Induce 参与Manifold 总管Volumetric efficiency 容积效率Turbine blade 增压机压片Adjacent 邻近的Swirl 漩涡Opposed piston 对置活塞Constant pressure system 定压增压Pulse system 脉动增压Thermal loads 热负荷Cross flow scavenge 横流扫去i Loop flow scavenge 回流增压Uniflow scavenge 直流扫气Blower 鼓风机Simplify 简化Lesson 10Thrust 推力Intermediate shaft 中间轴承Tail shaft 尾轴承Sterntube 尾轴管Cone 螺旋桨轴帽Mounte 安装Integral/independent 整体式/独立式Cate for 满足Shock load 冲击性负荷Thrust block 推力块Fitted bolt 紧固螺栓Bearing pad 承压块Pivot 支点，枢轴Tilt 倾斜Thrust Collar 推力环Oil scraper 刮油器Fabricate 铸造Aftermost tunnel bearing 尾轴管轴承Jounal bush 轴瓦Oil thrower ring 甩油环Gland 机械密封Outboard/inboard 舷外/内Stuffing box 填料箱Bulkhead 舱壁Lip seal 唇封Radial seal 径向密封Mate 配对Ingot steel 钢锭Taper 变细Fixed pitch propeller 定距桨Controlallable pitch propeller 变距浆Static 静态Dynamic 动态Lesson11直径Diameter半径radius孔，镗孔bore 行程stroke 平均有效压力MEP平均活塞速度mean piston speed 比燃油消耗率SFOC共轨common rail传统的conventionl 可用的available电磁阀magnetic valve/ solenoid valve 可靠性reliability耐用性durability精确地precisely精确的precise灵活地flexibly消耗consumption优化的optimized排放mission机动性maneuverability大修over hauls烟灰soot变量，可变的variable备份back-upLesson15轴向的axial离心的centrifugal水库，水柜reservoir安全阀relief valve容积volume排出的delivery排出阀discharge valve吸入阀suction valve空气室air vessel椭圆的elliptical螺杆screw双作用double acting往复泵reciprocating displacement pump 自吸self-priming维护，保养maintenance放残draining回转式容积泵rotary displacement pump 程序procedure轴封shaft sealing密封装置packing arrangement磨蚀abrasive腐蚀corrosive叶轮impeller外围periphery填料箱式packed gland转子element机械轴封mechanical seal耦合室coupling spacer紧tight导轮diffuser套筒drum串联in seriesLesson10Transmission SystemThrust shaft推力轴Intermediate shaft 中间轴Tail shaft 尾轴Thrust block推力轴承Thrust collar 推力环Lip seal 唇形密封Head tanker高置油箱Thread 螺纹Back press背压Boss 桨Pitch 螺距Radial face seal 径向面密封Fixed pitch propeller定距桨Stern tube bearing 尾轴管轴承Controllable pitch propeller变距桨Bearing pad 推力块Integral 完整的Cone 锥形物推冒Rudder 舱Hull 壳体Fitted blot 紧配螺栓Pivot 支点Tilt 使倾斜Scraper 刮油器Cascade 分布Fabricate 焊接Aftermost 靠近船尾Bush 轴瓦Tunnel 轴遂Thrower ring 甩油环Dip 浸入Lignum vitae铁梨木Timber 纤维Axial 轴向的Radial 径向的Stuffing box填料箱Helicoidat 螺旋面Blad 桨叶Rigid 刚性的Cascade 倾泻Lesson11 A leap in technology for marine enginesMagnetic valve 电磁阀Part load 低负荷Emission 排放Strock 行程Mean piston speed 活塞平均速度SFOC燃油消耗率Bore 缸孔Coastal 海岸的Diminish 使减少Dredger 挖泥船Leap 飞跃Optimal 最理想的Optimize 使最优化Precise 精确的Vital 至关重要的Back up 备份Lesson12 ME EnginesActuator 执行器Boester 升压器Diognostics 诊断Governor 调速器Hydraulic 水力的Inclination 倾斜Mechatronic 机械电子的Mesh 网孔Momentum 动力Proprietary 专利的Servo 伺服Counterpart对应物LESSON13 marine boilera and their constructionAttemperator 保温装置Casing 包装Conrection 传送对流Downcomer 下水道Furnace 炉子Gastight 不漏气Mounting 设备Propulsion 推力推进力Spherical 球型的Tangent 接触的Refractory lining耐火Saturated steam 饱和蒸汽Steam generation 蒸发Lesson14boiler mountings management and maitentBilge 舱底Condensate 冷凝物Bulge 不规则突起Detritus 碎石Dislodge 驱逐Fracture 破裂Friable 易碎的、Gauge 测量Periodically 优先的Salinity 盐分Sludge 淤泥Sample connection 取样口Soot blower 吹灰口Steam trap 凝气口Lesson15 marine pumpAxial flow pump 轴流泵Screw displacement pump 螺杆泵Displacement pump 容积式泵Peciprdate 螺杆泵Impeller 叶轮Volute 蜗壳Pump element 泵转子Priming umit引水单元Self-priming自吸Multi-stage多级Vane 叶片Wearing ring 承磨环Suction pipe 引入管NPSH汽蚀余量Configuration 构造Equilibrium平衡Pipe work 管系Alternately 交替的Valve arrangement阀组Air vessel空气室Dampen 减弱Vaper 水蒸气Entrained 引入空气Seizure 卡住Ridge凸台Erratically 不稳定Ground in 研磨Nesh 啮合Abrasive 磨蚀的Covrosive 腐蚀的Strip 拆开Bracket 支架Diffuser 导轮Coupling spacer耦合室Reservoir 储存器Lesson16marine refrigerationRefrigerant 冷剂Condenser 冷凝器Sub-cooled过冷Super heat 过热Evaporator 蒸发器Liquid receiver 储液器Drier 干燥器Unloading gear 卸载机构Hermetic 封闭的Semi-hermetic 半封闭的Oxide 氧化Brine 盐水Carbon dioxide二氧化碳Compact 紧凑的Bulb 湿包Fin 肋板Pass over 在上面流过Pass through 在里面穿过Ventilation 通风Solenoid valve 电磁阀Sub—devided 细分Rotor 螺杆Star wheel 星形轮Pitch 倾斜Fan 风机Coin 盘管Hunt 震荡Baffce 挡板Solenoid 螺线管Elastomer 弹性体Lesson17 marine refrigeration management and fault diagnosisLeak detector lamp检漏灯Concentration 浓度Liquid hammer水击Oil hammer油击Surplus 过多的Up right 直立Inclined 倾斜Violet 紫色Pale blue淡蓝Symptom 症状Press differential rely压差继电器Parge valve 放气阀Service valve 检修阀Duct 管子Under charge 冷剂不足Gauge 压力表Stem 阀杆Purge 放出Ascertain 确定Lesson20 Air Conditioning systemClimatic condition 气候条件Sufficient 足够充分Relative humidity 相对湿度Percentage 百分数Ratio 比例Vapor pressure蒸汽压力Absorb 吸收Heat source 热源Criculate 循环Renewal 补充Consume 消耗Single duct system 单风管系统Volume 容积Flexible 灵活性Tendency 趋势Incurs 引起Fabricated standard duct 预制标准尺寸风管Air terminals lined 空气终端管路Sound insulation material 隔音材料Centrifugal fan 离心式风机Driect expansion 直接膨胀Hermetic 气密的Thermostat 温度传感器Pnenmatic 气动型Capacity 载荷Stuffiness 不通风的Interval 每隔Grease 润滑Axial flow fan 轴流式风机Slight variation 微调Extreme weather 热带气候Tropical condition温和条件Intermediate weather极端天气Lesson19 Bilge Water Treatment SystemBilge water 舱底水Definition 定义Scope 范围Merely 仅仅Intermittent 断续Predictable 可预测Foresee 预见Soot water 吹灰冲洗水Leakage 泄露Detergent 洗涤剂Cat fine 催化粉末Soot 灰分Primary 第一级Particle 颗粒Portion 空间Emulsified 被乳化Organic solvent 有机溶剂Sludge 渣Nautical miles 海里Desposal 排放Legislation 立法Ecosystem 生态系统Constraints 约束Compactness 结构紧凑Droplet 滴Buoyancy 浮力Disperse 分散Immiscible 不融合的Shear 剪力Robust 耐用Adsorbent 吸附剂Polisher 洁油单元Zeolite 硅酸盐Capacity 能力Salinity 盐度Polymeric 聚合体Ultimate 根本上Primary 最初的Cross—flow membrane 横流膜Predicte 预期Filtration system 反渗透超滤系统Lesson20 Garbage Management and Biological Sewage TreatmentClinker 渣块Refuse 废物Dunnage 垫舱物料Crockery 陶器Comminute 粉碎Incinerator 焚烧炉Discharge 排出Authorize 批准In principle 原则上Engage 从事Comply 遵守Prescribe 规定Regulator 调节器Extended aeration process 充分曝气过程Bubbling 气泡Agitating 搅拌Bacteria 细菌Propagate 繁殖Thrives 兴旺Innocuous 无害的BOD生物需氧量Aerobic 好氧的Anaerobic 厌氧的。
EnglishofMarineEngineering（轮机英语）
EnglishofMarineEngineering（轮机英语）English of Marine Engineering（轮机英语）Unit 1 ：Main Propulsion Plant（船舶主推进装置）一、船舶动力装置概述●船舶动力装置的组成和类型、热机的类型和应用二、船舶柴油机1)船舶柴油机基本参数、特性指标2)船舶柴油机的工作原理3)船舶柴油机的基本结构4)船舶柴油机的燃油系统5)船舶柴油机的润滑系统6)柴油机的冷却系统7)柴油机的启动系统8)船舶柴油机操纵和控制系统、柴油机的运行管理、故障诊断三、船舶推进装置●推进装置的传动方式Unit 2 ：Auxiliary Machinery（船舶辅助机械）一、船用锅炉1)船用锅炉的类型和结构特点2)船用锅炉的运行管理、故障分析和排除二、船用泵1)船用泵类型；常见船用泵的工作原理和结构特点；船舶通用泵系的布置原则和特点2)常见船用泵的运行管理和故障排除三、船舶制冷和空调装置1)船舶制冷原理和制冷循环2)船舶空调系统的组成及主要设备；船舶空调装置的运行管理、故障分析和排除四、船舶防污染设备1)油水分离器的工作原理及运行管理2)焚烧炉的工作原理及运行管理3)生活污水处理装置的工作原理及运行管理五、分油机和海水淡化装置1)分油机的工作原理及运行管理2)海水淡化原理、主要设备和运行管理六、船舶甲板机械1)起货机的结构特点及其故障分析和排除2)锚机、绞缆机的结构特点及其故障分析和排除3)液压泵、控制阀件和油马达的结构特点；液压系统管理Unit 3：Marine Electrization and Automatization（船舶电气和自动化）一、船用发电机1)船用发电机的结构特点2)船用发电机的并车和解列3)船用发电机的故障分析和排除二、船用配电板1)主配电板的分类及组成2)应急配电板；配电箱三、船舶电气设备●船舶电气设备：船舶电气设备概况；电气控制设备；电气设备运行管理Unit 4 ：Marine Engineering Management（船舶轮机管理）一、操作规程●备车；巡回检查；完车二、安全管理知识1)船舶防火防爆的措施及守则2)轮机部操作安全注意事项；安全知识；机舱应急设备的使用及管理三、油、物料和备件的管理●燃油的管理四、船舶修理和检验1)修理的类别；轮机坞修工程2)船舶检验的类别与作用五、防污染管理及PSC检查1)《油类记录簿》与IOPP证书的管理2)PSC检查中的明显理由与更详细检查；PSC检查报告和缺陷的纠正Unit 5 ：International Convention and Regulations（国际公约与规则）一、STCW公约1)STCW78/95公约中有关轮机值班的基本原则2)轮机员的基本职责和道德；机架联系制度二、MARPOL公约●MARPOL73/78公约中有关含油污水的排放规则；有关国家、港口的防污染规则三、SOLAS公约●SOLAS公约的基本精神和基本原则四、ISM、ISPS等规则和公约1)ISM规则简介2)ISPS规则简介3)其他最新公约和规则。
轮机英语词汇(主机)
rotational speed：转速capacity: 功率steam turbine: 蒸汽轮机gas turbine: 燃气轮机speed reduction ratio: 减速比displacement: 排量flexible coupling: 柔性联轴节maintenance interval：检修周期gasoline engine：汽油机draft：吃水线torsional vibration damper: 减振器torque：扭矩prime mover：原动机be aligned with: 与…对中alignment：对中thermal efficiency：热效率loop scavenge：回流扫气cross scavenge：横流扫气uniflow scavenge：直流扫气supercharge：增压tappet clearance：挺杆间隙spark plug：火花塞indicator diagram：示功图indicator cards：示功图mechanical efficiency：机械效率compressed air: 压缩空气coolant：冷却剂occur：发生spray of fuel: 雾状燃油，油雾timing: 定时foul: 使…脏污fouling：污垢，脏污stuffing box：填料函，填料箱atmospheric pressure：大气压camshaft：凸轮轴cam：凸轮internal combustion engine：内燃机MIP（mean indicated pressure）：平均指示压力combustion chamber：燃烧室compression ratio：压缩比cylinder bore: 缸径overlap：重叠cross-head pin：十字头销bearing shell：轴瓦drill：钻孔，钻井，演习angle：角度expose：暴露，打开cycle：工作循环uncover：打开descending piston：下行的活塞value：值，数值decrease：降低，下降increase：上升，增加governor：调速器governor weight：调速器的飞重fuel injection：燃油喷射，喷油reliability：可靠性stroke coefficient：冲程系数give off：释放，放出naturally aspirated：自然吸气的，自然换气的admit：准许进入intake valve：进气阀linear motion：直线运动rotary motion：回转运动atomization：雾化cylinder firing pressure：气缸的爆炸压力be subjected to: 受到，遭受，承受ignition lag：滞燃期ignition delay period：滞燃期degree：程度，学位back pressure：背压thermal energy：热能mechanical energy: 机械能clockwise：顺时针地turbocharger：涡轮增压器brake horsepower：制动马力friction：摩擦single acting：单作用式的blow down：排气mixing：混合的mixture: 混合物advantage：优势，优点disadvantage：劣势，缺点compare：对比rocker arm：摇臂foundation：基础support：支撑，支持maintenance access：维修通道doors：道门in-line engine：直列式柴油机Vee engine：V型柴油机connecting rod large end bearing：连杆大端轴承connecting rod small end bearing：连杆小端轴承cast iron：铸铁cast steel：铸钢scavenging air box：扫气箱inertia：惯性thermal expansion：热膨胀aluminum：铝，铝的bronze：铜的mount：安装bolt：螺栓，用螺栓固定cross girder：横梁longitudinal girder：纵梁heat energy：热能float：漂浮，浮动piston skirt：活塞裙gudgeon pin：活塞销spur gear：正齿轮camshaft gear train：凸轮轴齿轮系starting air valve：空气启动阀side-chock bolt：侧楔形螺栓end-chock bolt：端楔形螺栓distance piece：调隙片compression plate：压缩片compression ratio：压缩比bearing housing：轴承座bearing cap：轴承盖bearing bush:轴瓦trunk piston：筒状活塞axial：轴向的stud：双头螺栓nut: 螺母enclose：密闭，密封guide：引导，导板tie rod=tie bolt=through bolt：贯穿螺栓entablature：机架column：机架cylinder block：气缸体external：外部的，外面的internal：内部的，里面的running-in period：磨合期load：负载，负荷，装载bearing wear：轴承磨损replace：替换，代替replacement：替换，代替clearance：间隙gap：间距tolerance：公差carrier ring：承磨环machine：机器，机械，加工machinery：机械（总称）machined：加工的，车削的ridge：凸台，凸肩groove：凹槽invariably：总是，一直forge：锻造forged：锻造的worn out：磨损的shim：垫片crank web：曲柄臂crank throw: 曲柄臂，曲拐crankpin：曲柄销crankcase：曲柄箱spring：弹簧，春天heat-resistant steel：耐热钢wearing resistance：抗磨，耐磨journal 轴颈sealing ring：密封环scraper ring：刮油环fuel valve：油头lubricator:注油器chromium-plated：镀铬的cylinder wall：汽缸壁lift out：吊出（活塞）piston ring belt: 活塞环区域cooling jacket：冷却水套balance：使…平衡shim：垫片thick：厚的thin：薄的thickness：厚度deformation：变形double bottom：双层底location：位置，定位locate：位于length: 长度width:宽度height：高度circular space：环形空间assemble：组装disassemble：拆卸assembly：组件fore and aft：前后semi-built：半组合式的transmit：传递，传送bending stress：弯曲应力torsion stress：扭曲应力shear stress：剪切应力turning gear：盘车机fitted bolt：拂配螺栓white metal：白合金horizontally：水平地be fitted with：装有，带有be provided with：装有，带有be equipped with装有，带有circumference [sə'kʌmfərəns]: 圆周，周长nip：过盈压隙crush：过盈joint face：连接面，结合面diameter：直径oil distributor ring：布油环scraper ring：刮油环oil control ring：刮油环protective layer：保护层lining：衬有，内衬copper-lead alloy：铜铅合金aluminum-tin alloy：铝锡合金thin-walled：薄壁的flame hardened：淬火处理的shipchandler：船舶供应商bore：孔，镗孔thermal stress：热应力compressive stress：压应力forced lubrication system：强制润滑系统output：功率，输出cooling chamber：冷却腔crosshead shoes：十字头滑块slipper：滑块guide shoes：滑块dowel pin：定位销machine-turned：车削的projection：凸台vertical flange：垂直法兰coil spring：圈簧surface：表面slopping surface：倾斜表面sliding bearing：滑动轴承sludge：油渣main propulsion diesel engine：主推进柴油机tension：张力under tension：承受张力heater：加热器electric heater：电加热器timing gear：定时齿轮chain drives：链条驱动机构coincide with：重叠，一致center of gravity：重心statically balanced：静平衡wrist pin：活塞销heat conductivity：导热性oil film：油膜excess：过多的excessive：过多的，过大的rigid：结实的，坚实的transverse girder：横梁jack bolt：撑杆螺栓tap-bolt：锥头螺栓solid forged：整体锻造的solid bearing：整体式轴承polish：抛光telescopic pipe：伸缩管sag：下垂sagging：下沉量component：部件corrosion resistant：耐腐蚀的flame screen：防火网罩watertight compartment：水密舱taper：锥形的，逐渐减小的insert：插入：插件stationary part：固定部件statically balanced：静平衡dynamically balanced：动平衡turbulence：涡流flywheel：飞轮kinetic energy：动能fluctuation：波动valve stem：阀杆valve head：阀头valve cage：阀壳heat dissipation：散热water seal：水封wet liner：湿式缸套dry liner：干式缸套test cock：示功考克gasket：垫片knurling：滚花sodium：钠cold clearance：冷态间隙thrust：推力side thrust：侧推力manifold：总管bundle：管束overload：过载plasma coated：等离子涂层的oil sump：油底壳treat：处理，对待treatment：处理advanced firing：早燃retarded firing：后燃，发火滞后air venting arrangement：放气装置prime：灌注，注油priming：灌注priming pump：引液泵fuel supply passage：供油管路viscosity regulator：粘度调节器lifting check：起阀压力试验fuel main：总管plunger：柱塞spindle：针阀available：可用的，可得到的manoeuvring condition：机动操纵状态specification：规格grade:规格specific gravity：比重specify：规定service tank：日用柜day tank：日用柜port：港口，开口pressurize：加压injector nozzle：喷油嘴clog：堵塞particle：颗粒，颗粒状index：刻度，指数reading：读数rack：齿条rack and pinion arrangement：齿条/齿轮装置transfer pump：驳运泵bunker tank：燃油舱banker list：加油单have much to do with：与…..有很大的关系have nothing to do with：与…..没有关系quality：质量quantity：数量earlier ignition：发火提早stick open：保持开启状态oil sump：油底壳settling tank：沉淀柜droplet：水珠，油滴strainer：粗滤器fine filter：细滤器at interval：定期地prevent from doing sth.:防止做某事set：设定setting：设定量，设定值preset：预先设定buffer tank：缓冲柜balance tank：平衡柜（集油柜）service tank：日用柜cleared of：排除，清除barrel：套筒sleeve：套筒pipe：管子duct：管道，导管hose：软管flash point：闪点overflow：溢出（满了溢出）spill：溢油full ahead：全速前进fuel consumption：燃油消耗save：挽救，救生，节省economical speed：经济转速purify：分离，清洁purifier：分水机clarifier：分杂机foreign matter：杂质follower：滚轮calorific value：发热值pour point：倾点diameter：直径original：原来的，开始的vibration：振动penetration of fuel：燃油穿透penetration：穿透力distribution of fuel：燃油分布minimize：使….最小化maximize：使…..最大化shut down：关闭，切断cut off：终止，关闭check valve：止回阀jerk pump：喷射泵meter：计量，测量，米proper metering：精确计量parameter：参数size：尺寸carbon accumulation：结炭flow rate：流速break up：分裂，破裂，分手manufacture：制造商precaution：预防措施contamination：污染，脏污cetane rating：十六烷值cetane number：十六烷值secure the fuel supply：切断燃油供应take place：发生，开始commence：发生，开始slope：斜面spill port：回流孔，溢流孔build up：建立，积聚helix：螺旋槽MCR：最大持续功率base circle：基圆sulfur：硫water vapor：水蒸汽acid：酸，酸的malfunction：故障ash：灰duplex pressure gage：双联压力表thermostatic：恒温的needle valve：针阀differential needle valve：差压式针阀constant volume：定容constant pressure：定压unit injector：单体式喷油器misfiring：不发火vanadium：钒sodium：钠indicate：显示，表示contribute to：有利于，导致block：堵塞compressibility:压缩性remove：清除，去除sounding tube：深管sounding rod：量油杆oil impingement：注油cavitation （erosion）:气穴，汽蚀booster pump：增压泵salt water：海水raw water：海水air cooler：空冷器make up：补充，补给distilled water：蒸馏水in contact with：与….接触facilitate：有利于，促进prior to：在….之前acid solution strength：酸性强度lime：石灰，氧化钙get rid of：去除，排除，摆脱release：释放mechanical property：机械性能expansion tank：膨胀水箱head tank：高置（膨胀）水箱coolant：冷却剂inoperative：不运转的，不运行的frost：结霜individual：单独的，独立的deposit：沉积物，沉淀物scale：水垢rust：生锈，铁锈dividing wall：分隔板overheat：过热explosion：爆炸chemical addition：投药，添加化学品additive：添加剂steam coil：蒸汽盘管anti-corrosion oil：防锈油inorganic inhibitor：无机缓蚀剂corrosion inhibitor：抗腐蚀剂regulate：调节modulate：调节head：压头volume：体积，容积closed cooling system：闭式冷却系统a portion of：一部分heat exchanger：换热器slightly：轻微的，轻度的nozzle holder：喷嘴座crack：裂纹suspect：怀疑baffle plate：挡板sacrificial zinc：保护性锌块soluble oil：可溶性油thermometer：温度计obstruct：堵塞，阻塞impeller：叶轮fin：翅片alarm：报警，警报器activate：激发，动作housing：壳体concentric：同心的bi-directional operation：双向运行compensating tank：补偿水箱（膨胀水箱）salinity：盐分，盐度alternative：选择，替代deaerating tank：除气柜three-way valve：三通阀flush：吹洗，冲洗oil barge：油驳interlocking device：连锁装置reversing：换向pilot air：控制空气，先导空气air distributor：空气分配器fusible plug：易熔塞guard against：防止air reservoir=air bottle=air receiver：空气瓶pneumatic control system：气动控制系统pneumatic tool：气动工具drain cock：放残考克blade：叶片turbine：透平remote valve：遥控阀air start lever：空气启动手柄instrument：仪表humidity：水分starting air distributor：启动空气分配器sufficient：充足的，足够的consecutive start：连续启动knocking sound：敲缸condensate：凝水condensation：冷凝run roughly：运转不平稳delay：推迟，延迟clearance volume：余隙容积two stage compressor：两级空气压缩机intercooler：中间冷却器，中冷器aftercooler：后冷器airborne：空气中携带的valve plate:阀片valve strip：阀片valve face：阀面valve seat：阀座volumetric efficiency：容积效率LP cylinder：低压缸HP cylinder：高压缸trip：跳闸overload relay：过载继电器dew point：露点splash lubrication：飞溅润滑water hammer：水击air delivery line：排出管路non-return valve：止回阀，单向阀carbonization：碳化throttling：节流solenoid：电磁的idle speed：怠速storage tank：储存柜neutralize：中和neutralization number：中和值alkalinity：碱detergency：清洁剂fundamental：基本的guard against：防止stern-tube bearing：尾轴承lignum vitae：铁梨木emulsion oil：乳化油，乳化防锈油sodium nitrite：硝酸钠additive：添加剂approved：认可的galvanize：镀锌investigation：调查gas seal 气封pot-shaped piston：筒状活塞analyze：分析total loss system：全消耗系统recirculation system：循环系统renew：更新，换新renewal：更新，换新static head：静压头in duplicate：一式两份，一式两台carry away：带走magnetic filter：磁性滤器blow out：吹洗in that：在于，因为former：前者latter：后者forced lubrication system：强制润滑系统employ：采用，使用，利用，雇佣hydrostatic lubrication：液体静力润滑impurity：杂质to a great extent：在很大程度上deterioration：恶化heat transfer：传热wear detritus：磨屑trouble-free life：无故障寿命dilute：冲淡，稀释，降低mist detector：油雾检测器monitor：检测，监控duplex filter：双联式滤器audible/visual alarm：声光报警shaker：振荡scuffing：划伤remain：保持remaining：剩余的retain：保留clogged：堵塞的hard varnish：硬的清漆pitting：点蚀oxidize：氧化carbon deposit：积碳detergent oil：净化油orifice：油孔diffuser：扩压器constant-pressure：定压增压pulse pressure：脉冲增压angle：角度，成….角度smoky exhaust：排气冒黑烟opposite：相反的，相对的supercharging：增压make use of：利用blower：鼓风机turboblower：涡轮增压器adjacent：相邻的in comparison to：与…相比compared to：与…相比fabricated：锻造的swirl：旋转rated speed：额定速度rated load：额定负载oxygen：氧气oxidize：使…氧化average：平均的velocity：速度directly proportional to：成正比characteristic：特点in conjunction with：和….一起performance：性能utilize：利用，使用furnish：提供muffle：消音，降低gas exchange：换气lose power：损失功率loss of pressure：失压take out=disengage:脱开put in=engage：合上FWE=finished with engine：完车give a trial：试车ahead and astern: 正倒车packing box：填料箱overhaul：大修stall：停止，停车enlarge：扩大，变大abnormal：不正常on no account：绝不，不可以seizure：卡住，咬缸gradually：逐渐地，逐步地remedy：补救，补修metalock：金属扣合法warm up:加温，暖机unless：除非surge：喘振spark：火星paint：油漆blistering：起泡peeling：剥落withdraw：取出routine 日常的，周期性的whilst=while：当…时候eliminate：消除，清除ambient temperature：环境温度regarding：关于with regard to：关于，对于….来说ventilation：通风vacuum：真空risk：风险，危险hazard：危险head wind：顶风heavy sea：风浪大combustion knock：燃烧过程粗暴wheelhouse：驾驶台contaminant：杂质，污染物cease：停止defect：损坏，缺陷sensor：传感器dead slow ahead：微速前进distribution：分配，布置，配电idle：闲置的guarantee：保证，确保pressure-volume diagram：压容图jerk pump：脉动泵，急拉式泵by-product：副产品erosion：剥蚀spark arrestor：火花消除器navigation：航行score：划痕scratch：刮痕abrasive particle：磨蚀颗粒pyrometer：高温计（测量排烟温度）manometer：压力计pressure gauge：压力表dial indicator：千分表，量缸表micrometer：千分表feeler：塞尺straight edge：直尺bridge gauge：桥规（轴颈下沉量，较小的主轴承磨损）blow-by：漏气break-in period：磨合期hone：搪磨detuner：减震器verify：检查，证实underway：航行时at partial load：部分负载localized：局部的local：当地的，机旁的file：锉blank off：堵死rotor：转子metal scraper：金属刮刀wrench：扳手moisture：水分muffler=silencer：消音器switch on：接通absolute pressure：绝对压力（=表压力+大气压力）air blast pump：抽气泵quay：码头direction handle：换向手柄coke deposit：积碳asphalt：沥青boss：桨毂hub：桨毂，轮毂variable pitch propeller：调距桨controllable pitch propeller：调距桨constant pitch propeller：定距桨fixed pitch propeller：定距桨tail shaft：尾轴intermediate shaft、；中间轴mass：重量in turn：依次，循序thrust block：推力块thrust pad：推力块reversing gear：换向装置axial movement：轴向运动solid propeller：整体式螺旋桨stem：船尾astern：船尾bow：艏，船头apparent slip：滑失比helix：螺旋线helicoidal：螺旋面，螺旋状的uniform pitch：定螺距non-uniform pitch：不定螺距pitch ratio：螺距比rubber：橡胶sterntube bearing：尾轴管轴承common rail system：共轨燃油系统VIT= variable injection timing: 可喷油定时。
船体和轮机常用英语单词汇总
船体aircraft carrier 航母submarine 潜艇air cushion vehicle 气垫船longitudinal strength 总纵强度transverse strength 横向强度local strength 局部应力hull 主船体superstructure 上层建筑stem 船首midship 船中stern 船尾forecastle 首楼brige 桥楼poop 尾楼deck house 甲板室ship bottom 船底ship side 舷侧upper deck 上甲板lower deck 下甲板transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁forepeak bulkhead 首尖舱壁afterpeak bulkhead 尾尖舱壁shell plate 外板seam 边接缝butt 端接缝strake 列板bottom plate 底板plate keel 平板龙骨bilge strake 舭列板side plate 舷侧外板sheer strake 舷顶列板second deck 第二甲板third deck 第三甲板platform deck 平台甲板deck plate 甲板板deck stringer 甲板边板sponson deck 舷伸甲板center keelson 中内龙骨side keelson 旁内龙骨T-bar T型材web 腹板bracket 肘板face plate 面板flange 折边板floor 肋板bilge bracket 舭肘板bulb plate 球扁钢angle bar 角钢bottom center girder 中底桁bottom side girder 旁底桁solid floor 主肋板watertight floor水密肋板bracket floor框架肋板lightened floor 轻型肋板stiffener 加强筋reverse frame 内底横骨bottom frame 船底肋骨inner bottom plate 内底板man hole 人孔margin plate 内底边板duct keel 箱型中底桁pipe tunnel 管隧longitudinal 纵骨bottom longitudinal 船底纵骨inner bottom longitudinal 内底纵骨bottom side tank 底边舱foundation seating 基座shaft tunnel 轴隧tunnel recess 尾室emergency exit 应急出口bilge keel 舭龙骨frame 肋骨integrated barge 分节驳main frame 主肋骨tweendeck frame 甲板间肋骨intermediate frame 中间肋骨web frame 强肋骨side stringer 舷侧纵桁side longitudinal 舷侧纵骨cross tie 撑杆wing tank 舷边舱ballast water tank 压载水舱torsion box 抗扭箱bulwark 舷墙fender 护舷材beam 横梁deck beam 甲板横梁half beam 半梁hatch end beam 舱口端横梁deck girder 甲板纵桁hatch side girder 舱口纵桁beam knee 梁肘板deck longitudinal 甲板纵骨web beam 强横梁cargo hatch 舱口hatch coaming 舱口围板gusset plate 菱形板hatch side cantilever 悬臂梁piller 支柱topside tank 顶边舱excess hatch 人员出入舱口expansion trunk 膨胀井cofferdam 隔离空舱partial bulkhead 局部舱壁plane bulkhead 平面舱壁bulkhead plate 舱壁板tweendeck bulkhead 甲板间舱壁vertical bow 直立型首raked bow 前倾型首clipper bow 飞剪型首icebreaker bow 破冰型首bulb bow 球鼻型首fore peak 首尖舱collision bulkhead 防撞舱壁raised floor 升高肋板panting beam 强胸横梁wash bulkhead 制荡舱壁chain locker 锚链舱stem 首柱steel plate stem 钢板首柱combination cast and rolled stem 铸钢和钢板混合式首柱forged steel stem 锻钢首柱thruster 侧推器elliptical stern 椭圆型尾cruiser stern 巡洋舰型尾transom stern 方型尾after peak 尾尖舱shaft tube 艉轴管cant frame 斜肋骨cant beam 斜横梁stern frame尾柱rudder post舵柱propeller post 螺旋桨柱shoe piece 尾柱底骨propeller shaft strut 艉轴架A-bracket 人字架shell bossing 轴包套spectacle frame 眼镜形骨架accommodation deck 起居甲板boat deck 艇甲板navigation deck 驾驶甲板compass deck 罗经甲板compass plateform 罗经平台expansion joint 伸缩接头engine casing 机舱棚derrick post 桅柱derrick plateform 起货机平台tower post 塔式桅pressure hull 耐压舰体pressure structure 耐压结构non pressure structure 非耐压结构pressure conning tower 耐压指挥台pressure tank 耐压水舱pressure bulkhead 耐压舱壁oil ballast tank 燃油压载水舱conning tower sail 指挥台围壳exhaust valve 排气阀camshaft 凸轮轴crankshaft 曲轴crosshead 十字头connecting rod 连杆tie bolt 地脚螺栓轮机英语ashore 在岸上，陆地上shipchandler 船舶供应商saloon 大台，大厅，酒吧，展览会场，motorman 机工agent 代理cabin 舱室corridor 走廊brief discription 简短，简要的介绍domestic 国内的，家庭的|佣人，国货materials 材料installation 安装，装置marine diesel engine 船用柴油机horsepower 马力diesel 柴油cylinder 汽缸bore 钻孔，孔cylinder bore 缸径piston 活塞stroke 冲程，打击，笔画piston stroke 活塞冲程compressor 压缩机the oil-burning vertical type auxiliary boiler 立式燃油辅助锅炉automatic changover switch 自动转换开关marine animals and plants 海洋动植物compound 混合，化合物，混合物，妥协chemical compound 化学添加剂corrosive 腐蚀copper 铜aluminium 铝instruction manual 说明书Asian 亚洲人alien 外国的，相异的，性质不同的，外侨，转让the living expenditure 生活费用spare part 备件urgent 急切的，迫切的recall the order 取消订单surveyor 验船师leakage of fuel oil 漏油nozzle nap喷嘴帽injector 喷油器on the spot 现场B register of shipping B船级社bunkering 加油terminal 终点，终极oil company’s terminal 油品公司码头barge 驳船application 应用，申请store 储备，储藏high reputation 信誉好tempting 诱人的，吸引人的quote 引述，举证catalogue 目录bolt 螺栓freon 氟利昂brake 刹车expansion valve 膨胀阀air-mailed 空运Fax 传真whole threaded 全丝双头螺栓stud 大头钉screw pitch 螺距hexagon nipple 六角管接头washer 垫圈，洗涤器，洗衣人micrometer 千分表the wire stripping pliers 剥皮钳specification 规格invoice 发票tug 拖轮joint 接头the harbour office 港务局specific gravity 比重viscosity 粘度warranty 担保，保证，授权substitute 代替duplicate 复制，副本alongside 在旁边，在…旁边portside 左舷starboard 右舷hose 软管diameter 直径gangway 跳板，舷梯the fire hoses and equipment 消防管道和设备precaution 预防，警惕plug 塞住the deck scupper pipe 甲板排水管leakage泄露choke 窒息，堵塞dismantle 拆除tank 舱室trim 整齐，修整the temperature correction factor 温度修正系数acid number 酸值ash content 灰度main engine 主机fuel oil heater 燃油加热器pilot 引水员lube oil 滑油diesel oil 柴油revolution 旋转，革命，运行，循环the hydraulic valve 液压阀nitrogen 氮installation 安装，就职，装置the warm-up valve 暖缸阀the circulating lube oil tank 循环油柜filter 过滤器clamp 夹紧，固定住joint 垫子previous 以前的，早先的generator 发电机the prime mover 原动机liner 钢衬crack 裂缝turbochanger 涡轮增压器shift 轮班，移动，转变main air compressor 主空气增压器workshop 车间overtime work 加班foreman 工头the air cooler 空冷器abnormal noise 声音异常inlet/outlet 进口/出口supercharger 增压器the tube leakage 管子泄露the fouling脏堵the chemical cleaning equipment 化学清洗设备the air seal 气封felt 毡silencer 消音器disassembling 解体the cooling copper tube 冷却铜管the cooling ribs around the tube管上的散热翅片make-do with sth 凑合auxiliary engine 辅机cylinder 汽缸the cylinder head 缸头ground 研磨the inlet and exhaust valves 进排气阀trial 试验the end cover 端盖the valve seat 阀座piston ring活塞环crank 曲轴the crank bearing 曲轴轴承the oil sump 油底壳magnet 磁铁storekeeper 保管员the special tool 专用工具torque spanner 扭力扳手screw nut 螺帽loose 松的hydraulic tool 液压工具groove 槽the piston ring groove 活塞环槽gap 天地，缺口，空白machined 车削加工过storeroom 仓库the worn-out flare 磨损的喇叭口the bearing shell 轴承瓦the piston pin活塞销rag 破布bulletin 公告scraper ring 刮油环in triplicate 一式三份burr 毛刺crank bearing bushes 曲柄销轴瓦polish 抛光oilstone 油石oil sump 油底壳replenish the oil 加油the scavenger pressure 扫气压力the engine trial 试车surge喘振dismantle 拆卸fly-wheel 飞轮the up-side-down type 倒挂式oil filter 滤油器the indicator cock 示功考克crankcase 曲柄箱boiler 锅炉weld 焊接the blow-down pipe 排污管slope vessel 污水船the flue door 烟道drawing 图纸you can count on me 你可以放心the combustion chamber 燃烧室refractory line 炉墙peeled off 剥落high percentage of carbon 高含碳量the boiler automatic feed control 锅炉自动给水控制the combustion automatic control 燃烧自动控制low water level 低水位the light resistor 光敏电阻the ignition electrode 点火电极the ignition injector 点火油头the buoy for the water level control 水位控制浮子the scale is very thick 水垢很厚the relay for the high and low water levels高低水位接触器the insulating material of some wires was aged and peeled off 一些电线的绝缘层都易老化并脱落avometer 万用电表the solenoid valve 电磁阀flange法兰blind plate 盲板the oil way 油路scavenge the boiler 炉内扫气。
船舶轮机英语集成
船舶轮机英语集成第 1 页船舶英语27．压缩环(气环) Compression ring目录28．刮油环(油环) Oil scraper ring一.职位及工种一．职位及工种(Titles and type of work) 29．减磨令Wear ring (copper ring)(Titles and type of work) ·····1 1．船长Captain 30．伸缩管(水拉管) Telescopic pipe二、柴油机类2．大副Chief officer 31．活塞冷却空间Piston cooling space(Words about diesel engine) ·····3 3．二副Second officer 32．填料箱(函) Stuffing box三、船舶机械类4．三副Third officer 33．填料箱密封环Sealing ring for Stuffing(Words about marine machinery) ··11 5．四副Fourth officer box四、阀门(Words about valve) ····14 6．水手长Boatswain 34．填料箱压缩环Pressure ring for Stuffing五、泵类(Words about pump) ··········16 7．水手Sailor & Seaman box六、甲板机械类（Deck machinery）······18 8．木匠Carpenter 35．填料箱刮油环Scraper ring for Stuffing七、工具类(Word about tools) ········20 9．轮机长Chief engineer box八、常用物料(Material in common use) 26 10．大管轮Second engineer 36．扫气箱Scavenging receiver九、常用紧固件11．二管轮Third engineer 37．扫气口Scavenging port(Part of fixation in common use) ···28 12．三管轮Fourth engineer 38．排十、常用油类(Oil in common use) ·····28 13．机匠长Chief motorman 39．十字头Cross head十一、常用量词15．机匠Fitter 40．十字头销Crosshead pin(Quantifier in common use) ·········29 16．加油工Oil man 41．十字头轴承Crosshead bearing十二、国家名称(Name of country) 。
【知识】船舶轮机英语：基础词汇
【知识】船舶轮机英语：基础词汇第六部分：基础词汇Ⅰ.技术术语 Technical Terms1、pump 泵①Supply pump供给泵②transfer pump 输送泵③circulating pump 循环泵④bilge pump 舱底水泵⑤ballast pump 压载水泵1、tank①drain tank 泄放柜②service tank 日用柜③settling tank沉淀柜④storage tank 储存柜⑤circulating tank 循环柜⑥used oil tank 废油柜⑦buffer tank 缓冲柜⑧overflow tank 溢流柜⑨Collecting tank 收集柜⑩expansion water tank 膨胀水箱2、water①sea water (S.W.) 海水②fresh water (F.W.) 淡水③operating water 工作水④sanitary water 卫生水⑤washing water 冲洗水⑥refilling water 再注水⑦feed water 给水⑧condensate water 冷凝水⑨bilge water 舱底水⑩sewage 污水2、oil①fuel oil (F.O.) 燃油②lubricating oil (L.O.) 滑油③engine oil 机油④cylinder oi l 气缸油⑤diesel oil (D.O.) 柴油⑥turbine oil 透平油⑦cool oil 冷却油⑧seal oil 密封油3、temperature (temp) 温度4、flow 流量5、pressure（press）压力6、power 功率10、level 液位11、vibration 振动12、normal/abnormal 正常/异常13、main/auxiliary (aux.) 主要/辅助的14、inlet/exhaust 进气/排气15、fire alarm 火警16、fail/failure 故障17、overload 过载18、no-voltage 失电19、leak/leakage 泄漏20、wrong-way 错向21、insulation(insul) 绝缘22、oil mist 油雾23、viscosity 粘度24、density 浓度25、salinity 盐度26、oil content 油含量27、pressure difference 压差28、switch 开关29、flame 火焰30、automatic（auto）自动的31、emergency 应急的32、standby 备用的33、screw 螺丝34、nut 螺母35、stud 螺柱36、meter 仪表37、thermometer温度计38、level gauge 液位计38、pressure gauge 压力表39、length 长度40、breadth 宽度41、height 高度42、meter 米43、centimeter 厘米44、millimeter毫米45、decimillimetre 丝米46、micrometer微米46、hundredth of one millimeter 丝47、de(rust)生锈（除绣）48、spare parts 备件49、spanner 扳手50、ahead/astern 正车/倒车51、screwdriver 螺丝刀（minus / plus）52、sludge 油渣53、electrician’s knife 电工刀54、decrustation pliers 剥线钳Ⅱ.（主机主要部件） Main Parts for M/E1、engine frame 机架2、cylinder 气缸3、piston 活塞4、crosshead 十字头5、bedplate 机座6、crankshaft 曲轴7、cylinder cover/head 气缸盖8、connecting rod 连杆9、turbocharger 增压器10、driving chain 传动链11、air cooler 空气冷却器12、scanvage box 扫气箱13、oil sprayer 喷油器14、oil nozzle 喷油嘴15、exhaust valve 排气阀16、sealing ring密封环17、cylinder liner 气缸套18、piston rod 活塞杆Ⅲ.机舱布置图 Engine room arrangement1、main engine /M.E. 主机2、intermediate shaft 中间轴3、bearing 轴承4、propeller shaft 螺旋桨轴5、stern tube艉管6、aft seal head tank 后密封油箱7、FWD seal head tank前密封油箱8、stern tube L.O. drain tank 艉管滑油泄放柜9、chemical cleaning tank 化学清洗柜10、L.O. drain tank11、sludge oil trap 油渣收集柜12、rust preventer tank 防锈剂柜13、 oily water separator油水分离器14、Low sea chest 低位海水门15、L.O. transfer pump16、bilge pump 舱底泵17、M/E lub oil pump18、M/E S.W. cooling pump 主机海水泵19、sludge pump 油渣泵20、ejector pump for F.W.G 造水装置工作水泵21、stern tube L.O. pump 艉轴管滑油泵22、H.F.O. Transfer pump 燃油输送泵23、ballast pump 压载泵24、bilge & G.S. pump 舱底总用泵25、Fire & G.S. pump 消防总用泵26、Provision Ref. Unit S.W. pump伙食冷藏海水泵27、aux. S.W. Cooling pump 辅海水泵28、L.O. purify cleaning tray 滑油分油机洗池29、L.O. purify. Operating water tank 滑油分油机工作水箱30、L.O. purify. Heater滑油分油机加热器31、diesel generator 柴油发电机组32、D/G F.W. Cooler 柴油发电机淡水冷却器33、boiler feed water pump 锅炉给水泵34、cascade tank 热井35、aux.condenser 大气冷凝器36、inspection tank 凝水检查柜37、filter 过滤器38、distilling plant 造水装置39、control air vessel 控制空气瓶40、control air dryer控制空气干燥器41、air compressor 空压机42、main air vessel 主空气瓶43、M/E F.O. heater 主机燃油加热器44、purif room exh fan分油机室抽风机45、sludge tank 油渣柜46、drinking water hydrophone tank 饮水压力柜47、calorifier 热水柜48、drinking water sterilizer 饮水消毒器49、emergency air compressor50、stern tube gravity oil tank艉管重力油柜51、antifouling system power unit防污系统电源箱52、ECR. Unit cooler 集控室空冷机53、overhead crane 机舱行车54、boiler feed water test kit 炉水试验台55、cylinder oil measuring tank气缸计量柜56、sink 洗池57、gas welder 气焊机58、E.L. welder 电焊机59、universal machine 组合机床60、driller 立式钻床61、bench 钳桌台62、vice台虎钳63、grinder 砂轮机64、cupboard 橱65、sewage treatment unit 生活污水处理装置66、composite boiler 燃油/废气组合锅炉67、forced draft fan 锅炉强力风机68、incinerator焚烧炉69、waste oil service tank 废油日用柜70、supply ventilating fans 送风机71、spark arrester消音器Ⅳ.Others1、shipyard 船厂2、shipbuilding 造船3、berth/slipway 船台4、marine diesel engine 船用柴油机5、bulk-cargo carrier 散装货船6、container ship 集装箱船7、oil tanker 油船8、tonnage 吨位9、merchant ship 民用船10、military ship (warship) 军用船11、drawing 图纸12、hull 船外壳13、bow/stern 船艏/船尾14、port/starboard 左舷/右舷15、deadweight 载重量16、displacement 排水量17、freeboard 干舷18、deck 甲板19、keel 龙骨20、anchor 锚21、rudder 舵22、bottom 底23、supersrtucture 上层建筑24、side25、weld 焊26、painting 油漆27、assemble 装配28、launching29、sea trial 试航30、delivery 交船31、tightness test 密性试验32、after service 售后服务33、approval 认可34、blue collar worker 蓝领35、maker36、rules and regulations 规则、规范37、chief engineer 轮机长38、chief officer大副39、clerk 事务员40、foreigner41、fore peak 艏尖舱42、aft peak 尾尖舱43、frame 肋骨44、cabin 舱室45、wheel house 驾驶室46、shaft tunnel 轴隧47、beam横梁48、manhole 人孔49、bulbous bow球鼻艏50、sea chest 海水门51、bulkhead 隔舱壁52、dry cargo hold 干货舱53、provision store 食品库54、passageway 走廊、通道55、refrigerating chamber 冷藏室Ⅴ甲板机械 Deck Machinery1、deck 甲板2、anchor chain（cable）锚链3、chain locker 锚链舱4、windlass 起锚机5、mooring hole 导缆孔6、bollard 带缆桩7、cargo winch 起货绞车8、hand rail 栏杆9、hawse pipe 锚链筒10、hatchcover 舱口盖11、hatch coaming舱口围板12、control cabin操纵室13、derrick 吊杆14、cargo hook 吊货钩15、mooring winches 系泊绞车16、wire cable 钢索17、vertical ladder 直梯18、wire steel 钢丝卷筒19、side scuttle舷窗20、rudder stock 舵杆21、rudder shaft 舵轴22、flag staff 旗杆23、ventilator 通风筒Ⅵ.管系 for piping1、Exhaust air system 排气系统Exhaust pipe for M.E（Generators / boiler / emergency generators）主机 / 发电机 / 锅炉 / 应急发电机2、Cooling Water System 冷却水系统①cooling fresh water (CFW) 淡水冷却水②cooling sea water (CSW) 海水冷却水3、fuel oil system 燃油系统①light diesel oil②heavy diesel oil (HDO)③fuel oil purifying 燃油净化④oil sludge 废油（污油）⑤fuel oil transferring 燃油输送4、Lubricating oil system①L.O for M.E(generator / stern tube)②Lub. oil transferring5、Compressed air system①high / low pressure air②starting air 起动空气③control air④remote control air 遥控空气⑤miscellanous air 杂用空气6、Ship systems①the bilge system舱底水②the ballast system 压载水③the water supply system 供水④the steam system 蒸汽⑤the drainage system 排水⑥the fire-fighting system 消防⑦the air measuring and filling system 空气测量注入⑧the level system 液位7、filter / filter gauze (screen)8、drainage valve sets9、pressure gauge 压力表9、vacuum真空表10、thermometer 温度计11、steel tube 钢管12、copper tube 铜管13、observation glass 观察镜14、funnel 漏斗15、hose 软管16、induction port 吸口17、bracker 支架18、shim (washer) 垫片19、flange 法兰20、connection 接口21、stainless steel pipe 不锈钢管22、threaded connection 螺纹接头23、sleeve pipe 套管24、flowmeter 流量计25、radiator 散热器26、pipe wrench 管子钳27、spanner 扳手28、pipe cutter 管子割刀29、scraper 刮刀30、vice 老虎钳31、screwdriver 螺丝刀32、torch 手电筒Ⅶ主要阀件铭牌 Main valve list1、slush valve 截止阀2、non-return valve 止回阀3、through-way valve 直通阀4、butterfly valve 蝶阀5、sluice valve 闸阀6、remote-control butterfly valve 遥控蝶阀7、quick closing valve 速关阀8、self-closing valve 自闭阀9、reducer valve 减压阀10、ball valve 球阀11、copper valve 铜阀12、steel valve 钢阀13、cast iron valve 铸铁阀14、stainless steel valve 不锈钢阀15、safety valve 安全阀16、temperature adjusting valve 温度调节阀17、thermostatic valve 恒温阀18、induction valve 进气阀19、exhaust valve排气阀20、drain valve 排泄阀21、fire valve 消防阀22、three-way valve 三通阀23、valve material①cast iron 铸铁②cast steel铸钢③stainless steel④bronze 青铜⑤brass黄铜⑥copper紫铜⑦nodular cast iron球墨铸铁Ⅷ.电力设备 electrical equipment1.emergency (diesel / tacho- / shaft) generator应急（柴油/ 测速/ 轴带）发电机2.servo (governor) motor 伺服（调速）马达3.ignition (current / voltage) transformer点火变压器（电流/电压互换器）4.converter 变流器5.frequency changer 变频器6.charger 充电器7.rectifier 整流器8.uninterrupted power source (UPS)不间断电源装置9.battery or storage battery蓄电池或蓄电池组10.main (emergency / power section) switchboard 主（应急/电力区）配电板11.generator (feeder) panel 发电机（馈电）屏12.charging & discharging panel 充放电板13.(radio / low voltage / internal communication) power distribution board无线电（低压 / 船内通信 / 电力）分电箱14.power unit for cathodic protection阴极保护电源箱15.test panel 电工试验板16.shore connection box 岸电箱17.junction box (with fuse) 接线箱（带熔断器）18.control console (panel) 控制台，集控台19.main engine control stand主机控制台20.motor starter 电动机起动器21.control box (panel) 控制箱（板）22.main engine safety (air conditioning) control box主机安全系统（空调）控制箱23.control box for singal light信号灯控制箱24.steering gear source box 舵机电源箱25.contactor 接触器26.relay 继电器27.control (pressure / change over) switch 控制（压力 / 转换）开关28.magnetic valve 电磁阀29.resistor 电阻器30.push button 按钮31.temperature transducer 温度变换器32.oil mist detector 油雾探测器33.fuse 熔断器34.Ammeter 电流表35.voltmeter 压力表36.power meter 功率表37.power factor meter 功率因数表38.watt-hour meter 电度表39.frequency meter 频率表40.flow meter 流量表41.speed indicator 转速表42.ohm meter 欧姆表43.welder 电焊机the 车床45.drilling machine 钻床46.planning machine 刨床47.grinding machine 砂轮机48.electric heater 电热器49.electric refrigerator 电冰箱50.electric fan 电风扇51.air conditioner 空调52.washing machine 洗衣机53.fresh water sterilizer 引水消毒器54.stator 定子55.rotor 转子56.neutral wire 零线（中性线）57.winding 绕组58.coil 线圈Ⅸ.illumination equipment 照明设备1.port (starboard) light 左右舷灯2.mast 桅灯(stern艉灯 / anchor锚灯 / steering操舵灯 / signal 信号灯 / flashing 闪光灯/ towing 拖船灯/ daylight signal 白昼信号灯/ pendant 舱顶灯/ fluorescent pendant 荧光舱顶灯/ ceiling 蓬顶灯/passage corner 走道角灯/ desk 台灯/ wall 壁灯/ berth 床头灯/ r oom’s nameplate 舱室铭牌灯/ chart table 海图灯/ flameproof 防爆灯/ flood 泛光灯（强光灯）/ search 聚光灯（探照灯）) light3.switch开关4.plug插头5.socket 插座6.socket box 插座箱Ⅹ.Navigation equipment 导航设备1.gyrocompass 电罗径2.magnetic compass 磁罗径3.feedback unit 反馈装置4.echo-sounder 回声测深仪5.log 计程仪6.master (slave) clock 母（子）钟7.radar 雷达8.radio direction finder 无线电测向仪9.Loran (radio navigation / satellite navigation) receiver劳兰（无线电导航 / 卫星导航）接收机10.VHF radio telephone transceiver 甚高频电话收发信机11.facsimile 传真机12.television set 电视机13.video camera 电视摄像机oxygen 氧气acetylene 乙炔nitrogen 氮气inter gas 惰性气体epoxy 环氧的resin 树脂chock楔子垫木soapy water 肥皂水anemometer 风速计manometer 压力（压强）表，气压表straight edge 直尺feeler gauge 塞尺steel scale 钢尺dial gauge 千分表micrometer 外径千分尺vernier caliper 游标卡尺spanner 扳手wrench 扳手screw driver 螺丝刀hammer 锤子clinometer 测斜仪chain block 手拉葫芦mandatory 命令、强制的Chlorinator 氯化器syphon=siphon 弯管，存水管，虹吸管blind 盲板booklet of piping procedure 工序，过程，步骤gymnasium 健身房galley 船上厨房motorcycle safety helmet 安全帽life belt 安全带glove 手套respirator 口罩overall 工作服 uniformelectric torch 手电筒 flashligheyeglass 眼镜elevator 电梯plank 厚木板stage 大舞台expressions 公式 formula（复数formulae）plus 加，正minus 减，负multiply 乘divide by 用…除equal to 等于sb entrust sb with sth 委托某人reply to 答复promise 许诺explanation 解释说明answer to 答案typist 打字员triangle 三角形quadrangle 四边形四角形pentagon 五角形inflator 打气筒tyre 轮胎wheel 车轮off duty 下班on duty 上班overtime 加班Slipway、shipway船台1.Lighting alignment for shafting & rudder system 轴舵系照光对中2.Stern tube boring 艉轴管镗孔3.Stern tube bush 艉轴衬套4.Stern boss艉轴壳5.forced fitting inspection压入配合检验6.oil jack（千斤顶）油泵7.（propeller shaft & stern tube bush）radial clearance （艉轴和艉管衬套）径向间隙8.axial clearance 轴向间隙9.Stern tube seals sealing 艉轴密封10. propeller installation force fitting压配11.pull-up length压进距离12.pull-up force 推进力13.oilpressure for boss 扩涨油压14.Zero point 零点15. Shrinkage 过盈量16.cleanness光洁度17.taper圆锥，斜度18. superposition 重合19. intersect 相交20.perpendicularity 垂直度21.vertical垂直的22.horizontal 水平的23. nut of stern shaft艉轴螺栓24.rudder 舵25.rudder blade 舵叶26.rudder stock 舵杆27.rudder pintle 舵销28.rudder tiller 舵柄29.rudder bush 舵承30.rudder horn 挂舵臂31. securing key 定位销，定位键32.protecting cover 保护帽33.grease牛油34.rudder angle 舵角35.full angle 满舵36. rudder blade’s stopper 防跳块37.temperature sensor 温度传感器38. inlet outlet 进出39. tolerance 公差，允许量40.wear down gauge 磨损规41.stern tube main chamber 大腔42.high pressure chamber 高压腔43.low pressure chamber 低压腔Engine Room 机舱1.Cleaning check：Storage oil tank of steering gear 舵机储存油箱（方形）Expansion oil tank of mooring winch 绞机膨胀油箱（圆形）Storage oil tank of mooring winch 绞机储存油箱Storage oil tank of windlass 锚机储存油箱（方形）Expansion oil tank of windlass 锚机膨胀油箱（圆形）Hydraulic oil tank of hatch cover 舱口盖液压油箱2.flushing of winch piping 绞机管路投油1.D/G pouring epoxy chock 发电机浇环氧2.holding down bolt 地脚螺栓3. deflection of crankshaft 曲轴甩档4.piston 活塞5.cylinder 气缸6. turbocharger 涡轮增压器1.Force measurement of M/E stay bolts 紧固螺栓2.piston rod and connection rod bolts 活塞杆和连杆螺栓3.bolts in drive end of crank 曲轴大端螺栓4.piston—piston rod—crosshead—connection rod—crank—crankshaft活塞活塞杆十字头连杆曲柄曲轴5.cam 凸轮6.camshaft 凸轮轴7.M/E chain cable 主机链条8.flooding test of M/E return oil pipes 压水试验9.propeller cap—propeller—stern tube seals—stern tube bush—stern shaft—intermediate shaft导流帽螺旋桨艉密封艉管衬套艉轴中间轴—intermediate bearing—flywheel (thrust shaft)中间轴承飞轮推力轴10.coupling reamer holes 联轴节铰制孔11.turning gear 盘车机12. spring 弹簧1.main air compressor 主空压机2.alignment of coupling flange 联轴节对中3.gap 裂面4.sag 位移1.steering gear 舵机2. ram roller bearing 舵机活塞杆轴承3. neck bush & cylinder 舵机活塞颈衬套和活塞缸体4. dimension measurement 尺寸测量1.fore draft valve艏吃水阀2.speed log 计程仪3.echo sounder 测深仪Quay、shipside、wharf、dock码头感谢阅读，这里是龙de船人获取更多资讯，请关注后输入关键字搜索投稿、建议、沟通：*****************。
船舶常用英语(一)汇总
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船第 1 页共24 页cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳. 专业.专注.hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长. 专业.专注.length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）. 专业.专注.bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器. 专业.专注.camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔. 专业.专注.duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟. 专业.专注.gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨. 专业.专注.keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板. 专业.专注.out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航. 专业.专注.sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算. 专业.专注.strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门. 专业.专注.weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料) T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力. 专业.专注.elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲. 专业.专注.lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差. 专业.专注.building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验. 专业.专注.pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度. 专业.专注.potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复. 专业.专注.12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start)不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammable vapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴. 专业.专注.4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲. 专业.专注.22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损. 专业.专注.7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热. 专业.专注.9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀. 专业.专注.14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊. 专业.专注.。
船舶常用英语(一)汇总
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard pro 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start) 不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammablevapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊。
船舶轮机英语lesson 13
Jimei university
The gudgeon pin is carried in bosses in the piston skirt. Generally the gudgeon pin is fully floating in both connecting rod small end and the piston bosses.
Jimei university
circlip
Jimei university
Bearings The main bearing shells are made of steel with a lining of bearing metal, which may be white metal, copperlead or aluminium-tin(锡) alloy; they often have a thin flash of lead or indium(铟元素) to provide a layer giving protection against corrosion.
Jimei university
Accordingly it is essential that the large end bolts are tightened correctly to the designed pull as under- or over-tightening will result in the housing bore departing from its true circular shape.
Jimei university
This is required much more often in the case of the exhaust valves because of operation at higher temperature and because the gases flowing through may contain particles of carbonaceous matter which occasionally get trapped under the valve seat causing pitting.
船舶轮机专业英语经典版
轮机部分Ⅰ.主机提交过程用语：（for Main Engine）1、请验收轴系找中。
Please check the alignment of the shafting.2、请验收主机对中。
Please check the alignment of M/E.3、请验收主机曲轴拐档（甩档） Please check and accept the crankshaft deflection.4、主机联结（贯穿）螺栓测力验收 Approval of force measurement of M.E. through bolts.5、紧拂螺栓安装验收。
Approval of the installation of fitted bolts.6、紧拂螺栓孔验收。
Approval of the fitted bolt holes.7、中间轴测力验收 Approval of force measurement of intermediate shaft.8、中间轴承间隙验收 Approval of intermediate bearing clearance.9、主机找中不好 The alignment of M/E is incorrect.10、轴系找中不好 The alignment of shafting is incorrect.11、曲轴拐档超差 The crankshaft deflection is over the allowance.12、请调整到范围内 Please make an adjustment.13、主机爆压 Explosive Pressure on M/E.14、主机轴马力 The BHP( brake horse power ) of M/E15、主机扭力 The torsional force of M/E.16、主机旁撑 M.E. side support.17、主机尾撑 M.E. stern support18、主机拉撑 M.E. fastening support19、起动主机 Start main engine20、起动反向 Start M/E reversely21、排温高（低） Exhaust temperature is too high (low).22、爆压高（低） Explosive pressure on M/E is too high(low).23、冷却水温度高（低） The temperature of the cooling water is too high (low).24、启动空气压力低 The pressure of starting air is too low.25、滑油压力低 The pressure of lub oil is too low.26、扫气压力低 The pressure o scanvage air is too low.27、增压器转速低 The rpm of turbocharger is too low.28、开启（关闭）主启动阀 Start (Stop) the main starting valve.29、启动（关闭）主滑油泵 Start (Stop) the main L.O. pump.30、启动辅助鼓风机 Start the auxiliary (anx.) blower.31、启动主海水冷却泵 Start the main sea water cooling pump.32、主机暖机 Preheat the M/E cylinder.33、循环滑油预热 Preheat the L.O. circulating pump.34、启动（关闭）燃油循环泵 Start (Stop) the F.O. circulating pump.35、启动（关闭）燃油供给泵 Start (Stop) the F.O. supply pump.36、燃油压力高（低） The pressure of F.O. is high (low).37、燃油调压阀失灵 The F.O. pressure adjusting valve doesn’t work.38、轻油转重油 Change from light oil to heavy oil.39、主机启动（反向）试验 M/E starting (reversing) test.40、应急停车试验 Test of emergency stop.41、集控室操纵 The engine control room control (the control from the control room)42、机旁操纵 Local control43、桥楼遥控操纵 The remote control from the bridge.44、主机飞车保护试验 Protection test of M/E flywheel trip.45、淡水高温停车试验 Shut-down test of F/W. high temp.46、滑油低压停车试验 Shut-down test of L.O. low press.47、高压油泵齿条格数 Tooth sector of high pressure oil pump.48、喷油提前角太大（小） The advance angle is too large (small).49、喷油嘴雾化不良 The atomization of nozzle is too poor.50、喷油嘴压力太高（低） The pressure of nozzle is too high (low).51、喷油嘴漏油 The nozzle leakage.52、盘车装置离合保护试验 The protection test of turning gear clutch.53、调速器有故障 The governor has failed.54、液压链条压紧装置 Hydraulic chain tightener.55、缸头启动阀 The cylinder cover starting valve.56、缸头启动阀发烫 The cylinder cover starting valve is too hot.57、缸头启动阀漏气 The cylinder cover starting valve leakage.58、气缸油单向阀漏 The cylinder oil one-way valve leakage.59、气缸油单向阀装反 The cylinder oil one-way valve is fitted reversely.60、气缸油进油过多(少) The inlet cylinder oil is too much (little).61、拉缸 Cylinder score62、咬缸 Cylinder seizing63、敲缸 Cylinder knocking64、燃烧不良 Poor combustion65、排气中有水份 The exhaust gas is with water vapour.66、排气冒黑烟（呈淡蓝色） The exhaust gas is black（light blue）.67、排气管振动（漏烟） Exhaust pipe vibration (leakage).68、排气管增加支架 Attached bracket of exhaust pipe.69、排气管支架螺丝未扳紧 The bracket of exhaust pipe.70、冷却水管漏水 The cooling water pipe leakage.71、滑油管漏油 L.O pipe leakage.72、油底壳(循环滑油舱 / 主机内部)不干净The Oil pan（The circulating L.O. tank / The inside of M/E ）is not clean.73、主机出油点不畅 The M/E oil outlets are blocked.74、主机内部螺丝保险未装好 The safety of inner screw of M/E is not fitted properly.75、主机贯穿螺丝泵紧提交 M.E. through bolt submission.76、主机底脚紧固螺丝提交 M.E bottom fastening bolt submission.77、滑油（燃油）自清滤器不动作 The L.O. (F.O.) filter doesn’t work.Ⅱ发电机提交过程用语：（for diesel engine generator）1、主发电机内部清洗提交 The cleanness inside the main generator to be confirmed.2、主发电机曲拐挡提交 The main generator crankshaft deflection to be confirmed.3、主发电机安装提交 The installation of main generator to be confirmed.4、飞车保护提交 The protection of flywheel trip to be confirmed.5、滑油低压停车提交 The auto-stop function of L.O. low pressure to be confirmed.6、淡水高温停车提交 The auto-shop function of F.W. high temperature to be confirmed.7、主发电机负载试验 The load test of main generator.8、100％负载试验 100％ load test of generator.9、调速器突加/突卸试验 Instant load/ unload test of governor.10、100％到50％突卸试验 100％ to 50% instant unload test.11、50％到零突卸试验 50％ to nil instant unload test.12、零到100％突加试验 Nil to 50% instant load test.13、主发电机并电试验 The parallel test of generators.14、测量热拐挡（外压） The measurement of thermal deflection (exterior pressure).15、应急发电机负荷试验 The load test of emergency generator.16、应急发电机飞车保护试验 The protection test of flywheel trip of emergency generator.17、应急发电机淡水高温停车试验 The auto-stop test of emergency generator F.W. high-temp.18、应急发电机滑油低压停车试验 The auto-stop test of emergency generator L.O. low-press.19、应急发电机调速突加突卸试验 The instant load & unload test of emergency generator governor.20、应急发电机合主发电机联锁试验 The parallel of emergency and main generators.Ⅲ空压机合空气系统提交用语（for air compressor and air system）1、空压机垫片提交 The air compressor washer to be confirmed.2、空压机找中提交 The alignment of air compressor to be confirmed.3、淡水高温报警试验 Alarm test of F.W. high temperature.4、滑油低压报警试验 Alarm test of L.O. low pressure.5、安全阀提交 The safety valve to be submitted.6、空压机冲气试验 The filling test of air compressor.7、空压机高压(低压)自动停车试验 High-pressure (Low- pressure) auto-stop test of aircompressor.8、主空气瓶密性提交 Gas tightness submission of main air reservoir.9、主空气瓶安全阀提交 The main air reservoir safety valve to be submitted10、控制空气减压阀试验 Test of control air pressure-reducing valve.11、控制空气瓶密性试验 Gas tightness test of control air reservoir.12、控制空气瓶安全阀试验 The safety valve test of control air bottle.13、干燥器效用试验 The effect test of dehumidifier.14、日用空气减压阀试验 The test of service air pressure-reducing valve.15、日用空气瓶密性试验 The gas tightness test of service air reservoir.16、日用空气安全阀提交 The safety valve of service air reservoir to be confirmed.17、副空气瓶密性试验 The gas tightness test of aux. air reservoir.18、副空气瓶安全阀提交 The aux. air bottle safety valve to be submitted.19、应急空压机安全阀试验 The safety valve test of emergency air compressor.20、应急空压机冲气试验 The filling test of emergency air compressor.Ⅳ. 锅炉提交用语：（for boiler）1、主锅炉密性试验 The tightness test of main boiler.2、制炉 Boiler pickling(浸酸，酸洗).3、炉内清洁提交 The inside cleanness to be checked.4、锅炉给水泵运转提交 The running test of boiler water-feed pump.5、给水泵真空（自动转换）试验 The vacuum test（the auto-shifting test）of water-feed pump.6、自动给水提交 The auto water-feed system to be confirmed.7、锅炉燃油泵安全阀提交 The safety valve of boiler F.O. pump to be submitted.8、锅炉燃油真空试验 The vacuum test of boiler F.O. pump.9、锅炉燃油泵自动转换试验 The auto-shifting test of boiler F.O. pump.10、锅炉安全阀提交 The boiler safety valve to be confirmed.11、锅炉蒸发量试验 The test of boiler evaporation.12、锅炉自动化试验 The automation test of boiler.Ⅴ.轴舵系提交过程用语（for shafting and steering gear system）1、请检验照光靶 Please check the lighting target.2、请检验轴系照光(舵系)对中 Please check the alignment of shafting（steering gearsystem）.3、请检验轴孔加工圆 Please check the shaft hole.4、请检验搪孔尺寸（光洁度） Please check the boring size（cleanness）.5、艉轴管衬套压紧验收。
最全轮机英语基本单词
yacht : [jɔt]n.快艇，(竞赛用的)帆船，游艇general cargo ship: 杂货船refrigerator ship :冷藏船cruiser n．游船dry bulk carrier 干散货船passenger liner 旅客班轮cruiser n．游船air cushion craft 气垫船barge-carrier 载驳货船bulk-carrier散货船catamaran 双体船container ship 集装箱船chemical carrier 化学品（运输船）diesel boa柴油机船dry cargo ship 干货船electric motor ship 电动机船ferry 渡船freighter (cargo ship) 货船fire boat 消防船hydrofoil craft水翼船Ice-breaker破冰船life boat 救生船LNG carrier（liquefied natural gas carrier）液化天然气（运输）船multi-purpose ship多用途船oil barge 油驳ore carrier（ore ship ）矿砂船passenger liner 定期客船pilot boat引航船roll - on / roll - off ship (Ro-Ro ship) 滚装船reefer ( refrigerator ship )冷藏船salvage vessel救助船scientific surveying ship科研考察船semi-container ship半集装箱船semisubmersible drilling vessel半潜式钻井船specialized duty vessel专业船tramp不定期货轮tug拖船10．商船：merchant ship11．油船：tanker 12．散货船：bulk carrier2.船舶主要部分船首：bow 船尾stern 左舷：port side 右舷：starboard side 艏楼：forecastle艉楼：poop 上层建筑：superstructure肋骨：frame二层甲板：tween deck机舱：engine room 水密分舱：watertight compartment 艏尖舱：fore peak tank艉尖舱：after peak tank 双层底舱：double bottom tank 制链器：chain stopper锚链舱：chain locker锚链管：chain pipe锚机滚筒：chain cable barrel锚链筒：hawse pipe标准罗经：standard compass磁罗经：magnetic compass主操舵罗经：main rudder compass 陀螺罗经：gyrocompass推进器：propeller3.船用柴油机工作原理1．船用柴油机：marine diesel2．内燃机：internal combustion engine3．气缸：cylinder 4．活塞：piston 5．细雾状燃油：fine spray of fuel6．曲轴：crankshaft7．推进器：propeller 8．循环：cycle 9．四冲程柴油机：four-stroke diesel10．进气：fresh air11．压缩：compession 12．膨胀：expansion13．排气：exhaust14．二冲程柴油机：two-stroke diesel17．下死点：B.D.C15．燃烧室：combustion chamber 16．工作原理：principle of operation 18．排气口：exhaust port 19．残留废气：residual exhaust 20．上死点：T.D.C21．燃油喷射：fuel injection 22．进气口：inlet port 23．工作冲程：working stroke24．减速齿轮箱：reduction gearbox25．交流发电机：alternator26．连杆：connecting rod 27．扫气口：scanvenging port4.船用柴油机的种类1.船用发动机：Marine engine2.紧凑：compact3.柴油机：diesel4．蒸汽机：steam turbine 5．气轮机：gas turbine6．内燃机：internal combustion engine7．输出功率：output power 8．制动马力：brake horsepower9．螺旋桨：propeller 13．燃油消耗率：fuel comsuption 14．锅炉：boiler15．有吸引力的：attractive16．集装箱船：container ship17．衰变：decay 18．通过比较：by comparision19．限制，约束：restriction20．叶片：blade21．有效马力：effective horsepower22．放射性的：radioactive23．船用核装置：marine nuclear plant24．货油泵：cargo oil pump固定件：fixed part 运动件：moving part 曲柄箱：crankcase缸套和衬套：cylinder and liner 气缸盖：cylinder cover 活塞：pistion气缸体：cylinder block 活塞头：piston crown 活塞杆：piston rod十字头：cross 连杆：connecting rod 主轴承：main bearing轴向推力：axial push端塞螺栓：side-chock bolt 从动轴：driven shaft 推力块：thrust block扫气箱：scavenging air box机座：bedplate 机架：frame冷却水套：cooling jacket 21．燃烧室：combustion chamber22．排气阀：exhaust valve23．燃油阀：fuel valve 24．起动阀：starting valve25．安全阀：safety valve26．示功器旋塞：indicator cock 27．冷却腔：cooling chamber28．活塞裙：piston skirt29．活塞环：piston ring30．垫圈：rubber ring31．往复运动：reciprocating movement 32．工作行程：power stroke6.燃油系统燃油系统：fuel oil system 运行和维护：operation and maintainence残碳值：carbon residues 燃油粘度：fuel oil＇s viscosity十六烷值：cetane number 热值：calorific value 闪点：flash point凝固点：setting point 比重：gravity 10.含水量：water content11．机械杂度：mechanical impurity12．重油：heavy fuel 13．渣油：residual oil14．沉淀柜：settling tank15．燃油舱：bunker tank16．日用柜：daily service tank17．细滤器：fine filter18．压力调节阀：pressure regulating valve19．针阀：needle vavle20．低油位报警：low tank level level alarm21．输送泵：transfer pump22．三通阀：three-way valve23．喷射泵：injection pump 24．过滤器：stainer7.润滑系统润滑油膜：lubricating oil film 运动件：moving part 运动条件：operation conditions油冷式活塞：oil cooled piston抗氧化：resistance to oxidation总量损耗系统：total loss system feeding循环式系统：circulating system传动装置：running gear燃烧室：combustion space活塞顶：piston crown活塞环：piston ring衬套壁：liner wall运动方向的改变：reversal of direction of motion机械注油器：mechanical lubricator曲轴箱：crankcase轴承：bearing17．活塞杆：piston rod 18．辅助设备：auxiliary equipment 19．泵：pump20．离心分离机：centrifuge8.水冷却系统燃油喷射阀fuel injector valve排气阀exhaust valve起动空气阀starting air valve机械强度mechanical strength内部管道internal passage热交换器heat exchanger气缸套冷却水循环泵cylinder liner circulating pump涡轮增压器turbo-blower闭式系统closed system开式系统open system压力水柜pressure tank海水循环式冷却器sea water circulated cooler heat exchanger汽蚀效应cavitation effect气囊steam pocket放气口air lock透气管ventilation pipe支路branch可视式流量计visual flowmeter喷嘴积碳nozzle deposited carbon滑油冷却器lubricating oil cooler盲板法兰blind-flange9.舱底和压载系统舱底水：bilge water 压载水：ballast water 相互连接：interconnec t涨水，进水：flood 在船外，到舷外：overboard 水密舱室：watertight compartment应急舱底水泵：emergency bilge pump 替换物，选择对象：alternative引水装置：priming device 到某种程度：to some extent 调节船舶吃水差：trim the vessel 切换阀箱：change-over chest10.管路系统发证机构：certifying authority铸铁：cast iron冲击载荷：shock loading易碎性：brittle nature 循环热处理：cyclic heat treatment低碳钢：mild steel气密结构：gastight structure热膨胀：thermal expansion 锅炉水舱柜：boiler feed water tank贯通配件：through fitting隔离空舱：cofferdam船体变形：deflection of ship construction1．safety valve（安全阀）2．steam stop valve（蒸汽截止阀）3．starting valve（起动阀）4．indicator cock（示功阀，示功考克）5．governing valve（调速阀）6．by-pass valve（旁通阀）7．main stop valve（主截止阀）8．hull valve（船体阀）9．flushing valve（冲洗阀）10．vent valve（排气阀）11．suction valve（进气阀）12．angle valve（角阀）13．automatic valve（自动阀）14．pressure valve（压力阀）15．quick-closing valve（速闭阀）16．self-closing valve（自闭阀）17．air filter（空气过滤器）18．coarse filter（粗滤器）19．fine filter（细滤器）20．heating circulating valve（加热循环阀）11.船用泵容积式泵：displacement pump 离心泵：centrifugal pump往复泵：reciprocating pump叶片泵：vane pump齿轮泵：gear pump旋转泵：rotary pump离心力：centrifugal force轴向的：axial flow涡轮，涡轮机：turbine自吸式：self-priming啮合齿轮：meshing gear蒸汽喷射器：steam ejector舵机液压系统：steering gear hydraulic system人字齿：double helical tooth大气压：atmospheric pressure立式泵：vertical pump12.舵机舵机：steering gear船级社：classification society转舵能力：steering capacity舵叶：rudder船舶吃水：ship’s draught驾驶台：bridge故障：trouble独立的：independent液压伺服马达：hydraulic telemotor舵机室：steering gear room舵柱：rudder stock液压油缸：hydraulic cylinder液压泵：hydraulic pump撞杆：ram舵角信号：signal of rudder angle13.甲板机械甲板机械：deck machinery克令吊：crane日常检验：routine checking锚泊设备：anchor arrangement 集装箱吊装设备厂：container handling facility原动机：prime mover装卸能力：handling capacity多旋转吊杆系统：multiwinch slewing derrick system安全工作负载：safe working load绞车卷筒：winch barrel or drum吊杆式起货装置：derrick crane system14.推进装置直接传动：direct drive推进效率：propulsion efficiency轴系：shaft system旋转方向：rotating direction齿轮传动：gear drive减速齿轮箱：reduction gear box减速装置：reduction arrangement双桨：twin-screw双舵：twin-rudde r双机并车：twin-engine incorporation多级：multi-stage带倒车离合器的减速：reduction with an astern clutch机舱：engine space挠性联轴节：flexible coupling安装误差：installation error可调螺旋桨：VPP or CPP固定螺旋桨：fixed pitch propeller定位：keep station15.轴系及设计程序传动轴系：transimission shafting system艉轴：stern shaft螺旋桨轴：screw shaft中间轴：intermediate shaft法兰联轴节：flange coupling可拆联轴节：removable coupling 隔舱填料函：compartment stuffing box推力环：thrust ring中空轴：hollow shaft轴倾斜度：shaft rake动态特性：dynamic characteristic扭振：torsional vibration纵振：longitudinal vibration回转振动：whirling vibration振动计算：vibration calculation 螺旋桨桨叶：propeller blade16.船舶设计与造船工程师造船工程师：naval architect造船工程学：naval architecture力矩平衡：moment balance重力平衡：weight balance轴马力：shaft horsepower净登记吨位：net register tonnage总吨位：gross tonnage扣除空间：deductible space流体力学：fluid mechanics结构强度：structural strength重货：high-density cargo轻货：low-density cargo港口税：harbor due母型船：projected ship重心：centers of gravity纵倾和稳性：trim and stability肋骨尺度：frame dimension外板厚度：plate thickness零件图：detail drawing总图：general drawing17.造船过程1.（船舶）下水滑道：launching way2．初步设计：preliminary design3．合同设计：contract design 4．详细设计：detail design5．运作要求：operational requirement6．缩尺船模（模型）：scale model7．成组建造技术：group technology to shipbuilding 8．大规模生产：mass production 9．任务系统：mission system10．交船日：delivery date 11．性能要求：performance requirements12．计划与调度：planning and scheduling13．个别零件：individual parts14．干船坞：dry dock15．投标过程：bidding process 16．船体分段：hull block17．装配线：assembly line18．概念设计：concept design18.船厂设施building period建造周期assembly line 装配（流水）线sloping shipway 有坡度船台，滑道building basin 船台floating dry dock 浮船坞engineering workshop轮机车间erection shop 装配车间fitting out quay舾装码头pumping station泵站，动力室repair quay 修船码头ship drawing office 船舶设计室20.船舶下水与舾装横向下水：sideway launching下水架：launching cradle滑道：standing way滑板：sliding way边墩：side support下水扳机：launching trigger局部压力：local pressure限制水域：restricted waterway减速力：retarding force阻力锚：drags21.适航1.试验大纲：sea trial programmers2．测速区：measured mile course3．重新试航：re-trial run4．性能试验：performance test5．动力装置：power plant6．抛锚试验：anchor-heaving trial7．适航性能：sea-keeping performance8．回转试验：turning trial9．潮汐效应：tidal effect10．逐级加速试航：Progressive speed trial11．续航力试验：endurance trial12．船舶试验协议：Protocol of T rials of the ship13．船舶设备清单：Inventory of the equipment of the vessel14．消耗品储备协议：Protocol of Stores of Consumable Nature15．完工图：finished drawings and plans16．交船：delivery of the vessel23.船级社1．合同前服务：pre-contract service2．提交检验申请：submit survey application3．申请评审及签署检验服务协议：aplication reviewing & survey agreement4．船舶审图及确定船用产品持证清单：drawing approval & required marine products list舶开工前检查：inspect before steel-cutting6．焊接工艺认可：welding technology approval7．焊工资格：welder qualification8．建造检验标准：standard of construct survey9．分段检验：structure inspection10．结构装配及焊接：structure assemble & welding11．安装主辅机、舵及轴系：installation of main engine, auxiliary mechinery & shafting 12．船台上或船坞内装配检验：assemble inspection on slipway or dock13．分段合拢检验：inspection of structure assemble14．焊缝检验：inspection of welding 15．无损探伤检验：NDT16．密性试验：tightness test17．船舶下水：lauching18．系泊试验：mooring trial19．航海试验：sea trial20．签发短期证书：issuance of interim certificates21．签发全期法定证书：Issuance of Full-Term Statutory Certificates22．CCS船舶录：Register of Ships by CCS23．签发全期船级证书：Issuance of Full-Term Class Certificates24．船级委员会：Class Committee。
船舶动力主要专业英汉词汇
主要专业词汇1、crew member船员2、captain船长3、chief engineer轮机长4、chief mate大副5、second engineer大管轮6、second mate二副7、third engineer二管轮8、third mate三副9、fourth engineer三管轮10、assistant engineer轮助11、electrical engineer电机员12、mechanic机工、机匠13、ship船舶14、diesel boat柴油船舶15、electric propulsion ship电力推进船16、lift on/off ship吊装船17、container ship集装箱船18、cargo ship货船19、dry cargo ship干货船20、harbor boat港作船21、passenger ship客船22、ore carrier矿砂船23、refrigerated cargo ship冷藏船24、multipurpose towing ship多用途拖船25、nuclear powered vessel核动力船26、steam turbine ship汽轮机船27、gas turbine ship燃气轮机船28、ocean－going ship远洋船29、oil water disposal boat油污水处理船30、oil tanker油船31、general cargo ship杂货船32、hull strength船体强度33、hogging中拱34、sagging中垂35、longitudiual rigidiy总刚度36、torsional strength扭转强度37、local strength局部强度38、shell plate外板39、hull structure船体结构40、transverse system of framing横骨架式41、longitudinal system of framing纵骨架式42、combination system of framing混合骨架式43、framing管架44、truss纵骨45、gorder纵行46、longitudinal纵骨47、single strake单板48、double bottom双层底49、bilge strake舭列板50、keel龙骨51、floor肋底52、frame肋骨53、frame spacing肋骨间距54、stern post尾柱55、stem首柱56、propeller strut尾轴架57、stern tube尾轴管58、shaft tunnel轴隧59、floating condition浮态60、buoyancy浮性61、heel横倾62、trim纵倾63、center gravity重心64、center offloatation漂心65、stability稳性66、metacenter稳心67、statical stability静稳性68、initial stability初稳性69、stability at large angles大倾角稳性70、rudder舵71、flat－plate rudder平板舵72、balanced rudder平衡舵73、streamline rudder流线型舵74、underhung rudder悬挂舵75、flag－type rudder襟翼舵76、steerine gear操舵装置77、anchor锚78、lightweight anchor大抓力锚79、admiralty anchor海军锚80、single－fluke anchor单爪锚81、stock anchor有杆锚82、anchor chain锚链83、chain cable compressor制链器84、mooring bitt带缆桩85、mooring cleat带缆羊角86、fairlead导缆器87、cargo handinggear起货设备88、derrick rig吊杆装置89、life boat救生艇90、unclosed lifeboat开敞式救生艇91、closed lifeboat封闭式救生船92、lifebuoy救生圈93、watertight door水密门94、sliding watertight door滑动水密门95、fire proof door防火门96、fuel oil system燃油系统97、tracer line伴热管98、fuel transfer pump驳运泵99、setting tank沉淀柜100、oil separator分油机101、oil collector集油柜102、daily service tank日用柜103、fuel comsumption rate燃油消耗率104、fuel booster pump燃油增压泵105、vent line透气管106、duplex filter unit双联滤器107、lubricating system润滑系统108、magnetic filter磁性滤器109、lube oil pump滑油泵110、lube oil cooler滑油冷却器111、lube oil drain tank滑油循环柜112、cylinder lubrication气缸滑油113、wet sump lubrication湿底滑油114、dry sump lubrication干底滑油115、oil sump油底壳116、cooling system冷却系统117、fresh water cooler淡水冷却器118、closed cooling water system闭式冷却119、fresh water cooler pump淡水冷却泵120、sea valve海底阀121、sea chest海底阀箱122、sea water strainer海水粗滤器123、expansion tank膨胀水箱124、heat exchanger热交换器125、operational code操作代码126、central cooling system中央冷却系统127、marine pollution prevention海洋防污染128、standard discharge connection标准排放接头129、standard shore connection标准通岸接头130、de－oiler除油器131、faecal coliform大肠杆菌132、shipboard marine pollution emergency plan（SMPEP）船舶海洋污染应急计划133、shipboard oil pollution emergency plan（SOPEP）船舶油污染应急计划134、pollution by garbage from ships船舶垃圾污染135、pollution by sewage from ships船舶生活污染136、shipboard incinerootion船上焚烧137、noise level on boardship船上噪音等级138、atmospheric pollution大气污染139、abandon ship弃船140、emergency equipment应急设备141、station bill应急部署表142、emergency bilge pump应急舱底泵143、emergency bilge suction应急舱底吸口144、emergency valve应急阀145、emergency battery应急蓄电池145、emergency generator应急发电机boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HV AC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线。
船舶轮机英语lesson 5
In use, the filling connections on deck are connected to shore hoses and the fuel oil bunkers(燃料舱) are then distributed to various double bottom, deep, wing and side tanks(双层底舱，深舱，舷侧 (xián cè)舱和边舱） as necessary.
精品资料
The fuel oil system for a diesel engine can be considered in
two parts—the fuel supply and the fuel injection systems.
精品资料
Fuel supply deals with the provision of the fuel oil suitable for use by the injection system.
精品资料
the sulphur(硫分) in it and its carbon residues( 残 炭 值 ) and ash( 灰 分 (huī fēn)) are factors that decide the formation of combustion products;
精品资料
and the engine’s maintenance has a lot to do with its flash and setting points(闪点(shǎn diǎn)和 凝 点 ), specific gravity( 密 度 ), viscosity, water content(水分) and the mechanical impurities(机械杂 质) in it.
船厂造船及修船船体、轮机、电气三大专业实用英语汇总
shell plate
船外板
bow plate
船艏外板
bracket plate
肘板
bulkhead plate
舱壁板
corrugated bulkhead plate
槽型舱壁板
bulwark plate
舷墙板
coaming plate
围板
connection plate
连续板
copper sheathing steel plate
平衡块
hinge
铰链
handle
把手
二、焊接
groove
支柱
frame
肋骨
base frame
基础台架
bear frame
支架
bilge frame
舭肋骨
bottom frame
船底肋骨
bow frame
首肋骨
bracket frame
肘板框架肋骨
bulbous bow frame
球鼻首肋骨
bulbous frame
球曲型肋骨
chief frame
主肋骨
铜-钢复合板
deck stringer plate
甲板边板
sloping plate
斜板
reinforcement plate
加强板
rudder plate
舵板
side plate
舷侧外板
skirt plate
裙板
stem plate
艏柱板
stern plate
艉柱板
platform
平台
engine-room platform
舭纵桁、舭纵骨
船舶专业英语词汇
ABS (American Bureau of Standard)美国船级社ANG (Angle Bar)角钢BFE (Builder Furnish Equipment)建造商提供设备BG (Bulk Carrier)散货船BHD (Bulkhead)舱壁BHP (Break Horsepower)制动马力BL (Base Line)基线BM (Breadth Molded)型宽BV (Bureau Veritas)法国船级社CAD (Computer Aided Design)计算机辅助设计CAM (Computer Aided Manufacturing)计算机辅助制造CB (Center of Buoyancy)浮心CCS (China Classification Society)中国船级社CF (Center of Floatation)漂心CFE (Contractor Furnish Equipment)承包商提供设备CG (Center of Gravity)重心CH (Channel)槽钢CM (Metacenter)稳心CPP (The Controllable Pitch Propeller)可调螺距桨CS (Carbon Steel)碳素钢DB (Double Bottom)双层底DK (Deck)甲板DM (Depth Molded)型深DNV (Det Norske Veritas)挪威船级社DWG (Drawing)图DWL (Design Waterline)设计水线DWT (Deadweight)载重量FAT (Factory Acceptance Test)工厂验收试验FB (Flat Bar)扁钢FEM (Finite Element Method)有限元法FPSO (Floating Production Storage Offloading) 浮（船）式生产储油卸油系统FSO (Floating Storage Offloading)浮（船）式储油卸油系统Fwd (Forward)向船艏GL (Germanischer Lloyd)德国船级社GM (Metacentric Height)初稳心高HP (Half Bulb Plate)球扁钢LBP (Length between Perpendiculars)垂线间长LCG (Longitudinal Center of Gravity)纵向重心LNG (Liquefied Natural Gas Vessel) 液化石油气船LOA (Overall Length)总长Long. (Longitudinal)纵骨LPG (Liquefied Petroleum Gas Vessel) 液化天然气船LR (Lloyd's Register)英国劳氏船级社MDK (Main Deck)主甲板MODU (Mobile Offshore Drilling Units)移动式近海钻井平台MS (Mild Steel)低碳钢MTO (Material Takeoff)材料估算NK (Nippon Kaiji Kyokai)日本海事协会OFE (Owner Furnished Equipment)船东提供设备OT (Oil Tight)油密PL (Plate)板RI (Register Italian)意大利船级社SB (Starboard)右舷Semi- (Semi-submersible Platform)半潜式钻井平台STLP (Suspended Tension Leg Platform)悬式张力腿平台TCG (Transverse Center of Gravity)横向重心TEU (Twenty-foot equivalent Unit)20英尺国际标准集装箱TLP (Tension Leg Platform)张力腿平台UCLL (Ultra Large Crude Carrier)超大型油船VCG (Vertical Center of Gravity)垂向重心VLCC (Very Large Crude Carrier)特大型油船WB (Web Bar)腹板WL (Waterline)水线WT (Water Tight)水密MECHANICAL & PIPING（轮机）：AHU (Air Handling Unit)通风装置BHP (Break Horsepower)制动马力A/C (Air Compressor)空气压缩机A/C (Air Conditioning)空调BB (Ball Bearing)滚珠轴承BRG (Bearing)轴承CAS NUT(Castle Nut)蝶型螺帽CCR (Central Control Room)中心控制室COW (Crude Oil Washing)原油洗舱DFO (Diesel Fuel Oil)柴油DPS (Dynamic Position System)动力定位系统DT (Double-Thread)双头螺纹FS (Forged Steel)锻钢FW (Fresh Water)淡水FO (Fuel Oil)燃油GRP (Glass-reinforced Plastic)玻璃钢HV A V (Heating Ventilation and Air-condition)暖通空调系统HPU (Hydraulic Power Unit)液压工作站LSA (Life Saving Apparatus)救生器具LCC (Local Control Console)机旁控制台LO (Lube Oil)滑油MDO (Marine Diesel Oil)船用柴油OS (Operation System)操作系统PLC (Programmable Logic Controller)逻辑控制单元PMS (Power Manage System)动力管理系统ELECTRICAL（电气）:AC (Alternative Current)交流电A VR (Automatic V oltage Regulation)自动电压调整计CCTV (Closed Circuit Television)闭路电视CMS (Cargo Monitoring System)货物监控系统DC (Direct Current)直流电DFT (Dry Film Thickness)干膜DG (Diesel Generator)柴油发电机DVD (Digital Video Disc) 数字化视频光盘EMSP (Emergency Shutter Panel)应急关断板ESS (Emergence Shutdown System)应急关闭系统GPS (Global Position System)全球定位系统HG (Harbor Generator)停泊发电机HT (High Temperature)高温JB (Junction Box)接线盒LED (Light Emitting Diode)发光二极管LT (Low Temperature)低温MCU (Main Control Unit)主控器箱MG (Main Generator)主发电机MUR (Manual V oltage Regulation)手动调压器NEMA (National Electrical Manufacturers Association) 国际电气制造业协会PA (Public Address System)公共寻呼系统PWM (Pulse Width Modulation)脉宽调制ST (Starter)启动器SWBD (Switch Board)配电盘，配电板UPS (Uninterrupted Power Supply)不间断电源VCR (Video Cassette Recorder)录像机PAINTING（涂装）:ARD (Alkyd Resin Deck)醇酸树脂甲板漆ARF (Alkyd Resin Finish)醇酸树脂面漆ARP (Alkyd Resin Primer)醇酸树脂底漆A/C (Anti-corrosive Paint)防腐漆CAF (Compressed Asbestos Fiber)压缩石棉填料EDP (Epoxy Deck Paint)环氧甲板漆EFP (Epoxy Finish Paint)环氧面漆EPP (Epoxy Primer Paint)环氧底漆ETPF (Epoxy Tank Paint Finish)环氧舱室面漆ETPP (Epoxy Tank Paint Primer)环氧舱室底漆ETP (Epoxy Topside Paint)环氧干舷漆ERL (Erosion Resistant Lacquer)防腐漆ECP (Etching Primer) 磷化底漆EPR (Ethylene-Propylene Rubber)乙丙橡胶F/C (Finish Coating)面漆IZP (Inorganic Zinc Primer)无机锌底漆IZSP (Inorganic Zinc Shop Primer)无机锌车间底漆UTP (Polyurethane Topside Primer)聚氨脂干舷漆TE (Tar Epoxy Paint)环氧焦油漆VTP (Vinyl Tar Primer)聚乙烯焦油底漆ZRP (Zinc Rich Primer)富锌底漆WELDING and Material（焊接与材料）ASTM (American Society for Testing Materials)美国材料实验协会AWS (American Welding Society)美国焊接协会FCAW (Flux Cored Arc Welding)药芯焊丝电弧焊FRP (Fiberglass Reinforced Polyester)玻璃钢GMAW (Gas Metal Arc Welding)气体保护金属极电弧焊GRP (Glass Reinforced Polyester)玻璃钢GTAW (Gas Tungsten Arc Welding)气体保护钨极电弧焊GW (Gravity Welding)重力焊MPI (Magnetic Particle Inspection) 磁粒检验NDE (Nondestructive Evaluation)无损鉴定NDT (Nondestructive Testing)非破坏性检验PVC (Poly Vinyl Chloride)聚氯乙烯S/W (Spot Weld) 点焊SAW (Submerge Arc Welding)埋弧焊SMAW (Shielded Metal Arc Welding)手弧焊UT (Ultrasonic Test)超声波检验WPS (Welding Procedure Sheet)焊接程序表WQT (Welding Qualification Test)焊工资格检验OTHERS（其它）AE (Assistant Engineer)助理工程师ANSI (American National Standards Institute)美国国家标准局API (American Petroleum Institute)美国石油协会ASME (American Society of Mechanical Engineers)美国机械工程师协会Bbls (Barrels) 桶（美制容量单位1桶= 159升），C.E. (Chief Engineer) 总工程师CEO (Chief Executive Officer)首席执行总裁CIS (Chinese Industrial Standard)中国工业标准CNOOC (China National Offshore Oil Company)中国海洋石油总公司Co Ltd.(Company Limited)（股份）有限公司cu.ft. (Cubic Feet) 立方英尺cu.in. (Cubic Inch) 立方英寸GB (Guo Biao)国标GM (General Manage)总经理H.Q. (Headquarters) 总部HSE (Health, Safety & Environment)健康，安全和环保ID (Inner Dimension)内径IEC (International Electro technical Commission)国际电工协会IMO (Intergovernmental Marine Organization)国际海事组织ISO (International Standardization Organization)国际标准化协会ITU (International Telecommunication Union)国际电信联盟Ksi (kilopounds per square inch)千磅/平方英寸N/A (None Applicable)不适用NACE (National Association of Corrosion Engineer)全国防蚀工程师协会NFPA (National Fire Protection Association)国家防火协会OD (outer Dimension)外径QA (Quality Assurance)质量保证QC (Quality Control)质量管理（检查）ST (Short Ton)短吨SOLAS (International Convention of the Safety of Life at Sea)国际海上人命安全公约Spec. (specification)说明书，规格书sq.ft. (Square Feet) 平方英尺sq.in. (Square Inch) 平方英寸PROPER NOUN（专有名词）:Basic Design(基础设计): Preparation of specification and plans/drawings outlining the design and in sufficient detail to gain Class approval.总括性的设计规格书和图纸等，其详细程度仅足可以通过船级社认可其设计思想。
船舶轮机英语集成
一．职位及工种(Titles and type of work)1．主管工程师Engineer in charge2 机务船东Superintendent &Super&Owner 3．助理工程师Assistant engineer4．验船师（机）Register 5．验船师（船）Surveyor二、柴油机类(Words about diesel engine)1．主机Main engine 2．二冲程柴油机Two-stroke diesel engine 3．四冲程柴油机Fore-stroke diesel engine 4．高速柴油机High speed diesel engine5 中速柴油机Middle speed diesel engine 6．低速柴油机Low speed diesel engine7．气缸盖(缸头) Cylinder head 8．安全阀Safety valve9．释放阀Relief valve 10．示功阀Indicator valve11．示功考克Indicator cock 12．空气起动阀Air starting valve13．起动空气分配器Air starting distributor14．油头(燃油喷射器) Fuel injector15．排气阀Exhaust valve 16．气缸套Cylinder liner17．冷却水套Cooling water jacket 18．气缸注油器Cylinder lubricator19．活塞Piston 20．活塞头Piston crown21．活塞裙Piston skirt 22．活塞销Piston gudgeon pin24．活塞杆Piston rod 25．活塞环Piston ring26．活塞环槽Piston ring groove 27．压缩环(气环) Compression ring28．刮油环(油环) Oil scraper ring 29．减磨令Wear ring (copper ring)30．伸缩管(水拉管) Telescopic pipe 31．活塞冷却空间Piston cooling space32．填料箱(函) Stuffing box 33．填料箱密封环Sealing ring for Stuffingbox 34．填料箱压缩环Pressure ring for Stuffingbox35．填料箱刮油环Scraper ring for Stuffingbox 36．扫气箱Scavenging receiver 37．扫气口Scavenging port38．排气口Exhaust port 39．十字头Cross head40．十字头销Crosshead pin 41．十字头轴承Crosshead bearing42．十字头滑块Crosshead slipper 43．滑块Guide shoe44．十字头导板Crosshead guide plate 45．连杆Connecting rod46．连杆大端轴承Big end bearing 47．连杆小端轴承Small end bearing48．曲柄轴承Crank bearing 49．曲柄销Crank pin50．曲轴Crank shaft 51．曲轴颈Crank journal52．曲柄臂Crank web 53．拐档差Crank deflection54．主轴承Main bearing 55．主轴颈Main journal56．轴承瓦Bearing bush 57．上轴瓦Upper bearing bush58．上轴瓦Upper half 59．下轴瓦Lower bearing bush60．下轴瓦Lower half 61．推力轴承Thrust bearing62．推力块Thrust pad 63．推力盘Thrust disc64．推力轴Thrust shaft 65．底座Bed plate66．机架Frame 67．曲柄箱Crank case68．曲柄箱导门Crank case door 69 曲柄箱防爆门Explosion-proof Crankcase. 70．定时齿轮Timing gear 71．飞轮Flying wheel72．凸轮Cam 73．凸轮轴Cam shaft74．喷油凸轮Fuel injection cam 75．链条Chain76．链条轮Chain wheel 77．链条箱Chain box78．推杆Push rod 79．摇臂Rocker arm80．排气阀Exhaust valve 81．吸气阀Suction valve82．排气总管Exhaust manifold 83．进气总管Air inlet manifold84．高压燃油管High pressure fuel pipe 85．活塞冷却水管Piston cooling water pipe 86．法兰Flange 87．贯穿螺栓Tie bolt (tie rod)88．端盖Side cover 89．滑油泵Lubricating oil pump90．燃油泵Fuel oil pump 91．滑油泵齿轮Gear for lubricating oil92．燃油泵齿轮Gear for fuel oil pump 93．叶轮Impeller94．柱塞Plunger 95．导杆Guide rod96．导套Sleeve 97．滚动轴承Ball bearing98．滑动轴承Sliding bearing 99．推力滚动轴承Thrust ball bearing100 推力面Thrust surface (thrustside) 101．盘车机Turning gear102．增压器Turbocharger 103．涡轮机(透平) Turbine104．涡轮Turbine wheel 105．涡轮叶片Turbine blade106．喷嘴Nozzle 107．废气叶轮Exhaust impeller108．废气叶轮片Exhaust blade 109．废气端Exhaust side110．透平端Turbine side 111．转子轴Rotor shaft112．油泵L.O.pump 113．换向装置Reversing device114．换向伺服期Reversing servomotor 115．压气机(鼓风机) Blower116．膨胀接Expansion joint 117．调速器governor118．飞重Flying weight 119．补偿阀Compensate valve120．针阀Needle valve 121．开口销Cotter pin122．轴封Shaft seal 123．机械密封Machinery seal124．配电盘Switchboard 125．应急配电盘Emergency switchboard 126．应急发电机Emergency generator 127．滤器Filter128．细滤器Filter 129．粗滤器Strainer130．滑油滤器L.O. filter 131．燃油滤器F.O. filter132．空气消音器Air intake silencer 132．空气滤器Air intake filter133．空气瓶Air bottle (receiver) 134．分油机Separator135．油水分离器Water-oil separator 136．净油机Purifier137．燃油净化器F.O. purifier 138．二氧化碳CO2139．二氧化碳瓶CO2 bottle 140．正时齿轮Timing gear141．导向棒装置Guide bar 142．注油器驱动Lubricator driver143．链条张紧装置Chain tightener 144．凸轮轴传动轮Chain wheel on cam shaft145．中间链链传动轮Intermediate chain wheel146．注油器驱动装置Lubricator drive 147．链条张紧装置Chain tightener 148．滚筒导座Roller guide housing149．应急操纵台Emergency console 150．力矩平衡器Moment compensator 151．主启动阀Main starting valve 152．启动空气分配器Starting air distributor 153．喷油器Fuel valve 154．扫气系统Scavenge air system 155．安全帽Safety cap 156．机座Bed plate 157．轴向振动减振器Axial vibration damper 158．贯穿螺栓Arrangement of staybolt 159．示功器驱动装置Indicator driver 160．端罩End shields 161．气缸架Cylinder frame 162．气阀传动装置Valve operating device 三、船舶机械类(Words about marinemachinery)1．船用锅炉Marine boiler 2．废气锅炉Exhaust boiler 3．辅锅炉donkey boiler 4．组合式锅炉Combined boiler 5．火管Fire tube 6．给水管Feed pipe 7．炉膛Furnace 8．炉墙Furnace wall 9．火侧Fire side 10．水侧Water side 11．燃烧器Oil burner 12．安全阀Safety valve 13．上排污Upper drain 14．下排污Lower drain 15．锅炉皮阀Mounting valve 16．水位计Water level gauge 17．压力表Pressure gauge 18．主汽门Main steam valve 19．玻璃管Glass tube 20．空调装置Air-conditioning plant 21．制冷装置Refrigerating plant 22．冰机Fridge. Machine 23．空气压缩机Air compressor 24．造水机Fresh water generator 25．板式冷却器Plate type cooler 26．机舱天车Engine room crane 27．天车导轨Crane rail 28．电磁阀Solenoid valve 29．舵机Steering gear 30．舵承Rudder bearing carrier 31．液压缸Hydraulic cylinder 32．废气涡轮增压器Exhaust gas turbocharger 33．弹簧阀Spring loaded valve 34．冷凝器Condenser 35．分油器Oil separator 36．轴带发电机Shaft generator 37．焚烧炉Oil burner 38．分油机Separator 39．分离筒Separator bowl 40．配水盘装置Paring disc device 41．转数计Revolution counter 42．控制阀Control valve 43．辅机Auxiliary machinery 44．制冷装置Refrigerating plant 45．海水淡化装置Sea water desalting plant 46．热交换器Heat exchanger 47．船用气瓶Marine air bottle 48．冷风机Cooler unit 49．防水风门Fire damper 50．气密挡板Gas tight damper 51．排气风机Exhaust fan 52．舱室通风机Cabin fan 53．机舱通风机Engine room fan 54．应急鼓风机Emergency blower 四、阀门(Words about valve)1．吸气阀Suction valve 2．排气阀Exhaust valve3．控制阀Control valve 4．导阀Pilot valve 5．单向阀Non-return valve 6．口琴阀Flap valve 7．调节阀Regulating valve 8．液压阀Hydraulic valve 9．膨胀阀Expansion valve 10．给水阀Feed valve 11．排水阀Discharge valve 12．截止阀Stop valve 13．吹泄阀Blow-off valve 14．空气阀Air valve 15．泄放阀Drain valve 16．止回阀Check valve 17．海底阀Sea valve 18．回流阀Retune valve 19．节流阀Throttle valve 20．进气阀Inlet valve 21．出气阀Outlet valve 22．热力阀Thermal valve 23．中央阀Center valve 24．单向阀One way valve 25．二通阀Two way valve 26．三通阀Triple valve 27．旁通阀By-pass valve 28．换向阀Change-over valve 29．减压阀Pressure-reducing valve 30．溢流阀Overflow valve 31．自闭阀Self-locking valve 32．针阀Needle valve 33．平衡阀Balance valve 34．循环阀Circulation valve 35．主阀Main valve 36．滑阀Slide valve 37．蝶阀Butter-fly valve 38．截止阀Shut-off valve 39．闸板阀Gate valve 40．通海阀Sea suction valve 41．吹除阀Sea chest cleaning valve 42．防浪阀Storm valve 43．舱壁阀Bulkhead valve 44．快关阀Emergency shut off valve45．呼吸阀Breather valve 五、泵类(Words about pump)1．电动泵Motor-driven pump 2．柱塞泵Plunger pump 3．叶片泵Vane pump 4．回转泵Rotary pump 5．齿轮泵Gear pump 6．往复泵Reciprocating pump 7．离心泵Centrifugal pump 8．真空泵Vacuum pump 9．螺杆泵Screw pump 10．喷射泵Ejector pump 11．冷却泵Cooling pump 12．淡水泵Fresh water pump 13．海水泵Sea water pump 14．给水泵Feed water pump 15．循环泵Circulating pump 16．锅炉给水泵Boiler feed pump 17．卫生水泵Sanitary pump 18．压载泵Ballast pump 19．舱底泵Bilge pump 20．污水泵Sewage pump 21．燃油泵Fuel pump 22．高压油泵High pressure pump 23．底压油泵Low pressure pump 24．驳运泵Transfer pump 25．增压泵Booster pump 26．消防泵Fire pump 27．通用泵G.S. pump 28．旋涡泵Regenerative pump 29．蜗壳泵V olute pump 30．导叶泵Diffuser pump 31．单联泵Simplex pump 32．双联泵Duplex pump 33．多联泵Multiplex pump 34．活塞泵Piston pump 35．减摇泵Anti-roll pump 36．总用泵General service pump 37．应急消防泵Emergency fire pump 38．扫舱泵Stripping pump 39．货油泵Cargo oil pump 40．滑油泵Lubricating oil pump 六、甲板机械类（Deck machinery）1．锚机Windlass 2．锚机轴Windlass shaft 3．刹车带Brake lining 4．离合器Clutch 5．锚链轮Anchor Chain wheel 6．轴承瓦Bearing bush 7．轴承盖Bearing cover 8．绞揽机Capstan 9．系揽绞车Mooring winch 10．卷缆车Reel 11．钢丝绳Wire rope 12．卡环Shackle 13．缆绳Mooring rope 14．滑轮Block 15．刹车装置Brake device 16．制链器Anchor chain stopper 17．舱盖滚轮Hatch cover wheel 18．舱盖铰链Hatch cover hinge 19．液压油缸Hydraulic jack 20．起货机Cargo winch 21．可令吊Crane 22．生活吊Accommodation crane 23．吊杆Derrick boom 24．桅杆Mast 25．救生艇Lifeboat 26．艇架Davit 27．艇机Lifeboat capstan 28．救生筏Life raft 29．救生衣Life jacket七、工具类(Word about tools)1．车床Lathe 2．刨床Planing machine 3．钻床Drill machine 4．砂轮机Grinding machine 5．磨床Grinder 6．铣床Milling machine 7．镗床Boring machine 8．手锤Engineer’s hammer 9．冲击板手Impact wrench 10．板手Spanner 11．活络板手Screw spanner 12．梅花板手Ring spanner 13．呆扳手Open spanner 15．套筒板手Socket spanner 16．管子钳Pipe spanner 17．螺丝刀Screw driver 18．钢丝钳Wire pliers 19．尖嘴钳Long nose pliers 20．钢锯Hack saw 21．剪刀Scissors 22．手电筒Torch 23．扁铲(凿子) Chisel 24．锉刀File 25．丝攻Thread tap 26．板牙Thread die 27．绞刀Reamer 28．刮刀Scraper 29．油石Oil stone 30．拔子(拉马) Puller 31．沙布Emery cloth 32．破布Rag 33．卷尺Measuring tape 34．空心冲Hole punch 35．样冲Joint punch 36．油壶Oil gun 37．牛油枪Grease gun 38．手电钻Handle drill 39．钻头Drill 40．液压千斤Hydraulic jack. 41．塞尺Feeler gauge 42．游标卡尺Vernier caliper 43．外卡尺Outside calipers 44．内卡尺Inside calipers 45．螺纹量规Screw gauge 46．桥规Bridge gauge 47．电焊机Electrode welding machine 48．气焊机Gas welding machine 49．电焊钳Electric welding pliers 50．气割枪Cutting touch 51．电焊条Electric soldering iron 52．电工刀Electrician knife 53．电笔Test pen 54．剥线钳Wire stripping pliers 55．圆规Compass 56．量表Gauge 57．拐档表Crank deflection gauge 58．深度规Depth gauge 59．千分表Micrometer gauge 60．台虎钳Table vice 61．柴油Diesel oil 62．滑油Lubricating oil 63．液压油Hydraulic oil 64．重油Heavy oil 65．燃油Fuel oil 66．黄油Grease 67．螺栓Bolt 68．螺帽Nut 69．垫片Washer 70．研磨沙Grinding sand 71．研磨膏Grinding paste 72．石棉板Asbestos plate 73．青壳纸Fish paper 74．盘根Packing 75．细钢丝Thin steel wire 76．密封圈Rubber seal ring 77．塑料管Plastic pipe 78．胶皮管Rubber hose 79．电灯泡Electric bulb 80．工作灯Working lamp 81．插头Electric plug 82．插座Electric socket. 93．喷砂机Sand blaster outfit 94．空气马达Air motor 95．油柜清洁器Tank cleaning machine 96高压冲水机High pressure hose for hydraulic 97．真空泵Vacuum pump 98．套筒扳手组Socket wrench set 99．深头套筒Deep socket wrench 100．套筒扳手Box wrench 101．单开口扳手Single open end wrench 102．双开口扳手Double open end wrench 103．转矩扳手Torque wrench 104．电动机扳手Motor wrench 105．侧剪钳Slide cutting plier 106．活节钳Combination plier 107．可调快速扳手Speed wrench 108．螺丝起子Screwdriver 109．偏向螺丝起子Offset screw 110．六角螺帽起子组Hexagon nut drivers set 111．手摇钻Straight hand drill 112．手工锯Hacksaw frame 113．锯片Hacksaw blade 114．砂纸Silicon paper 115．手拉葫芦Chain block 116．高压管High pressure hose 117．液压千金顶Hydraulic jack 118．锤子Hammer 119．平錾Cold chisel 120．活动扳手Adjustable wrench 121．螺丝刀Screwdriver 122．侧剪铗Side cutting hipper 123．螺栓剪Cable cutter 124．敲击管钳Rap wrench 125．砂轮Grinding wheel126．老虎钳Utility vise 127．直梯Straight ladder 128．踏梯Step ladder 129．平台推车Platform trunk 130．搬平车Gas cylinder carrier 131．给油机Grease lubricator 132．强力油泵Heavy duty pump oiler 133．油壶Oil jag 134．麻花钻Twist drill 135．绞刀Pin reamer 136．旋转中心钻Rolling center 137 ．外径测微计Outside micrometer with counter 138．六折式尺Six-folding rule 139．弹性带尺Convex rule 140．不锈钢直尺Stainless steel straight rule 141．平面规Surface gauge 142．平行直角定规Precision flat try square 143．温度计Thermometer八、常用物料(Material in common use)1．阀研磨剂valve grinding compound 2．电焊条steel electrode 3．气焊条Steel welding wire 4．细钢丝绳Seizing wire 5．刚焊条Steel welding rod 6．紫铜管Copper tube 7．乙炔气瓶Acetylene cylinder 8．木屑Saw dust 9．水泥Cement 10．石灰Lime 11．帆布手套Canvas glove 12．垫片Gasket. 13．氧气瓶Oxygen cylinder 14．抹布Rag 15．垫隙片Shim 16．电线Wire 17．电缆Electric cylinder 18．电池Rag 19．灯泡Bulb 20．胶布Insulating tape 21．插头Plug 22．插座Socket 23．保险丝Fuse 24．不锈钢Stainless steel 25．铸铁Cast iron 26．黄铜Brass 27．青铜Bronze 28．铝合金Aluminium alloy 29．橡胶Rubber 30．石棉Asbestus 31．低碳钢Soft steel 32．高碳钢High-carbon steel 33．合金钢Alloy steel 34．木材Wood 35．塑料Plastic 36．球墨铸铁Nodular iron 九、常用紧固件(Part of fixation in common use)1．螺栓Bolt 2．螺丝Screw3．螺母Nut 4．方头螺栓Sq head bolt5．埋头螺栓Counter sunk head screw 6．套筒螺栓Socket head bolt 7．定位螺栓Set screw 8．十字接头Cross9．锥形销Taper pin 10．锁紧螺母Lock nut 11．六角头螺栓Hex head bolt十、常用油类(Oil in common use)1．汽油Gas oil 2．煤油Kerosene 3．润滑油Lubricating oil 4．汽缸油Cylinder oil 5．压缩机油Compressor oil 6．齿轮油Gear oil7．机油Motor oil 8．凡士林Vaseline9．燃油Fuel oil 10．油脂Grease 11．柴油Diesel oil十一、常用量词(Quantifier in common use)1．件，只，个Piece 2．条，张，片Sheet3．双Pair 4．套，组，副Set.5．盒Box 6．箱Case7．瓶Bottle 8．米Meter9．厘米Centimeter 10．毫米Millimeter11．公斤Kilogram 12．克Gram13．公升Liter 14．平方Square15．袋Bag 16．码Yard17．吨Ton 18．磅Pound19．加仑Gallon 20．立方Cubic十四、船用动态常用单词(marine tends word)1．停靠Alongside 2．接近Approach3．停泊Berth 4．浮筒Buoy5．码头Pier 6．港口Port7．移泊Shift 8．航次V oyage9．试验Try 10．值班Watch 11．航行Sail十五、船舶机电设备操作词汇(manipulate of marine equipment)1．调整Adjust 2．压载Ballast3．转换Change over 4．清洁Clean5．联接Connect 6．排放压载Deballast7．放残水Drain 8．卸载Off9．油漆Paint 10．接通Put on 11．吹灰Soot blown 12．开始Start13．顶端Top 14．洗Wash 15．吹Blow 16．检查Check 17．铲Chip 18．断开Cut out 19．排放Discharge 20．除垢Descale 21．检验Examine 22．受载On(load) 23．用泵排出Pump out 24．调整Set 25．停止Stop 26．调驳Transfer 27．加满Top up十六、故障常用单词(words about malfunction)1．失常的Abnormal 2．烧坏Burn3．堵塞Clog 4．裂缝Crack 5．变形Deform 6．毁坏Destroy 7．磨损Wear 8．出故障In trouble 9．敲击Knock 10．松开Loose 11．不对中Misalign 12．不足的Insufficient 13．失灵Out of order 14．过载Overload 15．过度磨损Over-worn 16．尺寸过大Oversized 17．尺寸过小Under-sized 18．振动Vibrate 19．不平的Uneven 20．不准确Inaccurate 21．全船断电Black out 22．出故障Fail 23．关掉Shut off 24．弯曲Bend 25．停车Break drown 26．腐蚀Corrode 27．腐蚀的Corrosive 28．损坏Damage 29．有毛病的Faulty 30．有缺陷的Defective 31．破裂Fracture 32．卡住Jam 33．漏泄Leak 34．漏泄的Leaky 35．融化Melt 36．噪声Noise 37．过热Overheat 38．咬住Seize 39．紧的Tight 40．松的Loosen 41．发现Find 42．停止Stop43．脏的Dirty 44．油污的greasy45．失效的ineffective 46．椭圆形的oval47．点不着火misfire 48．接错misjoin49．放错misplace 50．老化perish51．麻点pit 52．凸起ridge53．划伤score 54．拉痕scuff十七、保养检修常用词汇(Words about maintain and examination) 1．卡死Blind 2．用卡钳量Caliper3．关闭Close 4．解体Disassemble5．安装Fix 6．组装Box up 7．检验Check 8．拆卸Dismantle9．装配Fit 10．紧固Fasten11．测量Gauge 12．安装Install 13．测量Measure 14．打开Open 15．上油漆Paint 16．换新Renew 17．上紧Tighten 18．洗Wash 19．涂油脂Grease 20．松开Loosen 21．加油Oil 22．检修Overhaul 23．重新组装Reassemble 24．测取读数Take reading25．拧开螺栓Unbolt 26．抽出Withdraw二十、常用词组（Phrases in common use）1．发现已无法修复found beyond repair 2．发现尺寸过大found over-sized 3．发现反应缓慢found slow function 4．发现不正常found out of order 5．发现不合标准found not up to standard 6．发现不准确found inaccurate 7．发现失去作用found out of function 8．发现轧住found seized 9．发现过热found overheated 10．发现过度磨损found excessive wear 11．发现过度磨掉found worn out 12发现有一点倾斜found a little bit inclined 13．发现不正常found abnormal14 发现因过热而损坏found destroyed by overheating 15．发现龟裂found chapped 16．发现塌陷found collapsed 17．发现运转失灵found out of operation 18．发现呈椭圆形found oval 19．发现拉痕found scored 20．发现拉毛found scuffed 21．发现变形found deformed 22．发现松动found loose 23．发现油污found greasy 24．发现肮脏found dirty 25．发现咬住found stuck 26．发现挤压found squeezed 27．发现弯曲found bent 28．发现故障found faulty 29．发现损坏found damaged 30．发现破碎成片found broken to pieces 31．发现部分剥离found partly detached 32．发现部分堵塞found partly choked 33．发现剧烈震动found violent vibration 34．发现烧坏found burnt 35．发现断裂found fractured 36．发现接地found earthed 37．发现敲缸found knocking 38．发现溶化found melted away39 ．发现泄漏found leaking (found leaky) 40 ．发现冻结found stuck fast by icing 41．发现锈蚀found rusty 42．发现失效found ineffective 43．发现故障found out of order 44．发现结霜found frosted 45．发现丢失found lost 46．发现出故障found in trouble 47．发现失灵found out of order 48．发现失灵found out of action 49．发现不一致found out of operation 50．发现错位found out of place二十一、常用动词和例句(Verb in common use and example)1．借borrow 我要向你借这份图纸I want to borrow the drawing from you.我可以向你借这个手锤吗? May I borrow the hammer from you? 2．裂break 阀杆断裂了The valve spindle is broken.滚动轴承断裂成碎片了The ball bearing are broken to pieces. 3．加强build up 叶轮应该堆焊The impeller should be built up by welding. 4．烧burn 电动机烧了The motor is burnt. 5．进行carry out 应进行负载试验The load test should be carried out. 6．吹blow 管子必须用压缩空气吹清The pipe should be blown with compressed air. 7．铸cast 按原样铸造一个Cast one piece as per sample.8．引起cause 损坏是有剧烈振动引起的The damage was caused by violent vibration. 9．倒角chamfer 油槽须倒角Oil groove is to be chamfered.法兰切削后须倒角The flange should be chamfered after being machined. 11．龟裂chap 轴瓦上的白合金龟裂了The white metal on the bearing bush is chapped. 12．核查check 用桥规核查主轴承Check the main bearing with bridge gauge.修理前后要核查拐档Check the crankshaft deflection before and after repair. 13．清洁clean 装前须清洁Clean it before fit back. 14．阻塞clog 燃油滤器阻塞了The fuel filter is clogged. 15．涂漆coat 用红丹涂管子Coat the pipe with red lead.泵壳里涂防护漆The pump casing is to be coated with anti-fouling. 17．连接connect把电动机和淡水泵连接起来Connect the motor with the fresh water pump 18．腐蚀corrode泵壳和叶轮均有腐蚀The pump casing and impeller are corroded. 19．盖cover请把所有卸下的部件盖起来Please cover all the removed parts. 20．裂二号缸头裂开穿透至冷却水空间No.2 cylinder head is cracked. 21．吊crane 把液压马达吊上岸去修理Crane the hydraulic motor ashore for repair. 22．割cut 把底座割掉Cut off the bedplate. 23．损坏damage 滚动轴承严重损坏The ball bearings are seriously damaged. 24．脱落detach 白合金部分脱落了The white metal is partly detached. 25．查看detect 查看氟里昂系统有无泄漏Detect the Freon system for leakage. 27．脱开disconnect 把起动空气管脱开Disconnect the starting air pipe. 将发电机与原动机脱开。
轮机英语(精编文档).doc
【最新整理，下载后即可编辑】轮机英语词汇1、pump 泵①Supply pump供给泵②transfer pump 输送泵③circulating pump 循环泵④bilge pump 舱底水泵⑤ballast pump 压载水泵1、tank①drain tank 泄放柜②service tank 日用柜③settling tank沉淀柜④storage tank 储存柜⑤circulating tank 循环柜⑥used oil tank 废油柜⑦buffer tank 缓冲柜⑧overflow tank 溢流柜⑨Collecting tank 收集柜⑩expansion water tank 膨胀水箱2、water①sea water (S.W.) 海水②fresh water (F.W.) 淡水③operating water 工作水④sanitary water 卫生水⑤washing water 冲洗水⑥refilling water 再注水⑦feed water 给水⑧condensate water 冷凝水⑨bilge water 舱底水⑩sewage 污水2、oil①fuel oi l (F.O.) 燃油②lubricating oil (L.O.) 滑油③engine oil 机油④cylinder oil 气缸油⑤diesel oil (D.O.)柴油⑥turbine oil透平油⑦cool oil冷却油⑧seal oil密封油3、temperature (temp) 温度4、flow 流量5、pressure（press）压力6、power 功率10、level 液位11、vibration 振动12、normal/abnormal 正常/异常13、main/auxiliary (aux.) 主要/辅助的14、inlet/exhaust 进气/排气15、fire alarm 火警16、fail/failure 故障17、overload 过载18、no-voltage 失电19、leak/leakage 泄漏20、wrong-way 错向21、insulation(insul) 绝缘22、oil mist 油雾23、viscosity 粘度24、density 浓度25、salinity 盐度26、oil content 油含量27、pressure difference 压差28、switch 开关29、flame 火焰30、automatic（auto）自动的31、emergency 应急的32、standby 备用的33、screw 螺丝34、nut 螺母35、stud 螺柱36、meter 仪表37、thermometer温度计38、level gauge 液位计38、pressure gauge 压力表39、length 长度40、breadth 宽度41、height 高度42、meter 米43、centimeter 厘米44、millimeter毫米45、decimillimetre 丝米46、micrometer微米46、hundredth of one millimeter 丝47、de(rust)生锈（除绣）48、spare parts 备件49、spanner 扳手50、ahead/astern 正车/倒车51、screwdriver 螺丝刀（minus / plus）52、sludge 油渣53、electrician’s knife 电工刀54、decrustation pliers 剥线钳Ⅱ.（主机主要部件）Main Parts for M/E1、engine frame 机架2、cylinder 气缸3、piston 活塞4、crosshead 十字头5、bedplate 机座6、crankshaft曲轴7、cylinder cover/head 气缸盖8、connecting rod 连杆9、turbocharger 增压器10、driving chain 传动链11、air cooler 空气冷却器12、scanvage box 扫气箱13、oil sprayer 喷油器14、oil nozzle 喷油嘴15、exhaust valve 排气阀16、sealing ring 密封环17、cylinder liner 气缸套18、piston rod 活塞杆Ⅲ.机舱布置图Engine room arrangement1、main engine /M.E. 主机2、intermediate shaft 中间轴3、bearing 轴承4、propeller shaft 螺旋桨轴5、stern tube艉管6、aft seal head tank 后密封油箱7、FWD seal head tank前密封油箱8、stern tube L.O. drain tank 艉管滑油泄放柜9、chemical cleaning tank 化学清洗柜10、L.O. drain tank11、sludge oil trap 油渣收集柜12、rust preventer tank 防锈剂柜13、oily water separator油水分离器14、Low sea chest 低位海水门15、L.O. transfer pump 16、bilge pump 舱底泵17、M/E lub oil pump 18、M/E S.W. cooling pump 主机海水泵19、sludge pump 油渣泵20、ejector pump for F.W.G 造水装置工作水泵21、stern tube L.O. pump 艉轴管滑油泵22、H.F.O. Transfer pump 燃油输送泵23、ballast pump 压载泵24、bilge & G.S. pump 舱底总用泵25、Fire & G.S. pump 消防总用泵26、Provision Ref. Unit S.W. pump伙食冷藏海水泵27、aux. S.W. Cooling pump 辅海水泵28、L.O. purify cleaning tray 滑油分油机洗池29、L.O. purify. Operating water tank 滑油分油机工作水箱30、L.O. purify. Heater滑油分油机加热器31、diesel generator 柴油发电机组32、D/G F.W. Cooler 柴油发电机淡水冷却器33、boiler feed water pump 锅炉给水泵34、cascade tank 热井35、aux.condenser 大气冷凝器36、inspection tank 凝水检查柜37、filter 过滤器38、distilling plant 造水装置39、control air vessel 控制空气瓶40、control air dryer控制空气干燥器41、air compressor 空压机42、main air vessel 主空气瓶43、M/E F.O. heater 主机燃油加热器44、purif room exh fan分油机室抽风机45、sludge tank 油渣柜46、drinking water hydrophone tank 饮水压力柜47、calorifier 热水柜48、drinkingwater sterilizer 饮水消毒器49、emergency air compressor 50、stern tube gravity oil tank艉管重力油柜51、antifouling system power unit防污系统电源箱52、ECR. Unit cooler 集控室空冷机53、overhead crane 机舱行车54、boiler feed water test kit 炉水试验台55、cylinder oil measuring tank气缸计量柜56、sink 洗池57、gas welder 气焊机58、E.L. welder 电焊机59、universal machine 组合机床60、driller 立式钻床61、bench 钳桌台62、vice台虎钳63、grinder 砂轮机64、cupboard 橱65、sewage treatment unit 生活污水处理装置66、composite boiler 燃油/废气组合锅炉67、forced draft fan 锅炉强力风机68、incinerator 焚烧炉69、waste oil service tank 废油日用柜70、supply ventilating fans 送风机71、spark arrester消音器Ⅳ.Others1、shipyard 船厂2、shipbuilding 造船3、berth/slipway 船台4、marine diesel engine 船用柴油机5、bulk-cargo carrier 散装货船6、containership 集装箱船7、oil tanker 油船8、tonnage 吨位9、merchant ship 民用船10、military ship (warship) 军用船11、drawing 图纸12、hull 船外壳13、bow/stern 船艏/船尾14、port/starboard 左舷/右舷15、deadweight 载重量16、displacement 排水量17、freeboard 干舷18、deck 甲板19、keel 龙骨20、anchor 锚21、rudder 舵22、bottom 底23、supersrtucture 上层建筑24、side 25、weld 焊26、painting 油漆27、assemble 装配28、launching 29、sea trial 试航30、delivery 交船31、tightness test 密性试验32、after service 售后服务33、approval 认可34、blue collar worker 蓝领35、maker 36、rules and regulations 规则、规范37、chief engineer 轮机长38、chief officer大副39、clerk 事务员40、foreigner41、fore peak 艏尖舱42、aft peak 尾尖舱43、frame 肋骨44、cabin 舱室45、wheel house 驾驶室46、shaft tunnel 轴隧47、beam横梁48、manhole 人孔49、bulbous bow球鼻艏50、sea chest 海水门51、bulkhead 隔舱壁52、dry cargo hold 干货舱53、provision store 食品库54、passageway 走廊、通道55、refrigerating chamber 冷藏室Ⅴ甲板机械Deck Machinery1、deck 甲板2、anchor chain（cable）锚链3、chain locker 锚链舱4、windlass 起锚机5、mooring hole 导缆孔6、bollard 带缆桩7、cargo winch 起货绞车8、hand rail 栏杆9、hawse pipe 锚链筒10、hatchcover 舱口盖11、hatch coaming舱口围板12、control cabin操纵室13、derrick 吊杆14、cargo hook 吊货钩15、mooring winches 系泊绞车16、wire cable 钢索17、vertical ladder 直梯18、wire steel 钢丝卷筒19、side scuttle舷窗20、rudder stock 舵杆21、rudder shaft 舵轴22、flag staff 旗杆23、ventilator 通风筒Ⅵ.管系for piping1、Exhaust air system 排气系统Exhaust pipe for M.E（Generators / boiler / emergency generators）主机/ 发电机/ 锅炉/ 应急发电机2、Cooling Water System 冷却水系统①cooling fresh water (CFW) 淡水冷却水②cooling sea water (CSW) 海水冷却水3、fuel oil system 燃油系统①light diesel oil②heavy diesel oil (HDO)③fuel oil purifying燃油净化④oil sludge 废油（污油）⑤fuel oil transferring燃油输送4、Lubricating oil system①L.O for M.E(generator / stern tube)②Lub. oil transferring5、Compressed air system①high / low pressure air②starting air起动空气③control air④remote control air遥控空气⑤miscellanous air杂用空气6、Ship systems①the bilge system舱底水②the ballast system 压载水③the water supply system供水④the steam system 蒸汽⑤the drainage system排水⑥the fire-fighting system 消防⑦the air measuring and filling system空气测量注入⑧the level system 液位7、filter / filter gauze (screen)8、drainage valve sets9、pressure gauge 压力表9、vacuum真空表10、thermometer 温度计11、steel tube 钢管12、copper tube 铜管13、observation glass 观察镜14、funnel 漏斗15、hose 软管16、induction port 吸口17、bracker 支架18、shim (washer) 垫片19、flange 法兰20、connection 接口21、stainless steel pipe 不锈钢管22、threaded connection 螺纹接头23、sleeve pipe 套管24、flowmeter 流量计25、radiator 散热器26、pipe wrench 管子钳27、spanner 扳手28、pipe cutter 管子割刀29、scraper 刮刀30、vice 老虎钳31、screwdriver 螺丝刀32、torch 手电筒Ⅶ主要阀件铭牌Main valve list1、slush valve 截止阀2、non-return valve 止回阀3、through-way valve 直通阀4、butterfly valve 蝶阀5、sluice valve 闸阀6、remote-control butterfly valve 遥控蝶阀7、quick closing valve 速关阀8、self-closing valve 自闭阀9、reducer valve 减压阀10、ball valve 球阀11、copper valve 铜阀12、steel valve 钢阀13、cast iron valve 铸铁阀14、stainless steel valve 不锈钢阀15、safety valve 安全阀16、temperature adjusting valve 温度调节阀17、thermostatic valve 恒温阀18、induction valve 进气阀19、exhaust valve排气阀20、drain valve 排泄阀21、fire valve 消防阀22、three-way valve 三通阀23、valve material①cast iron铸铁②cast steel铸钢③stainless steel④bronze青铜⑤brass黄铜⑥copper紫铜⑦nodular cast iron球墨铸铁Ⅷ.电力设备electrical equipment1.emergency (diesel / tacho- / shaft) generator应急（柴油/ 测速/轴带）发电机2.servo (governor) motor 伺服（调速）马达3.ignition (current / voltage) transformer点火变压器（电流/电压互换器）4.converter 变流器5.frequency changer 变频器6.charger 充电器7.rectifier 整流器8.uninterrupted power source (UPS)不间断电源装置9.battery or storage battery蓄电池或蓄电池组10.m ain (emergency / power section) switchboard 主（应急/电力区）配电板11.g enerator (feeder) panel 发电机（馈电）屏12.c harging & discharging panel 充放电板13.(radio / low voltage / internal communication) power distributionboard无线电（低压/ 船内通信/ 电力）分电箱14.p ower unit for cathodic protection阴极保护电源箱15.t est panel 电工试验板16.s hore connection box 岸电箱17.j unction box (with fuse) 接线箱（带熔断器）18.c ontrol console (panel) 控制台，集控台19.m ain engine control stand主机控制台20.m otor starter 电动机起动器21.c ontrol box (panel) 控制箱（板）22.m ain engine safety (air conditioning) control box主机安全系统（空调）控制箱23.c ontrol box for singal light信号灯控制箱24.s teering gear source box 舵机电源箱25.c ontactor 接触器26.r elay 继电器27.c ontrol (pressure / change over) switch 控制（压力/ 转换）开关28.m agnetic valve 电磁阀29.r esistor 电阻器30.p ush button 按钮31.t emperature transducer 温度变换器32.o il mist detector 油雾探测器33.f use 熔断器34.A mmeter 电流表35.v oltmeter 压力表36.p ower meter 功率表37.p ower factor meter 功率因数表38.w att-hour meter 电度表39.f requency meter 频率表40.f low meter 流量表41.s peed indicator 转速表42.o hm meter 欧姆表43.w elder 电焊机44.l athe 车床45.d rilling machine 钻床46.p lanning machine 刨床47.g rinding machine 砂轮机48.e lectric heater 电热器49.e lectric refrigerator 电冰箱50.e lectric fan 电风扇51.a ir conditioner 空调52.w ashing machine 洗衣机53.f resh water sterilizer 引水消毒器54.s tator 定子55.r otor 转子56.n eutral wire 零线（中性线）57.w inding 绕组58.c oil 线圈Ⅸ.illumination equipment 照明设备1.port (starboard) light 左右舷灯2.mast 桅灯(stern艉灯/ anchor锚灯/ steering操舵灯/ signal信号灯/ flashing 闪光灯/ towing 拖船灯/ daylight signal 白昼信号灯/ pendant 舱顶灯/ fluorescent pendant 荧光舱顶灯/ ceiling 蓬顶灯/passage corner 走道角灯/ desk 台灯/ wall 壁灯/ berth 床头灯/ room’s nameplate 舱室铭牌灯/ chart table 海图灯/ flameproof 防爆灯/ flood 泛光灯（强光灯）/ search 聚光灯（探照灯）) light3.switch开关4.plug插头5.socket 插座6.socket box 插座箱Ⅹ.Navigation equipment 导航设备1.gyrocompass 电罗径2.magnetic compass 磁罗径3.feedback unit 反馈装置4.echo-sounder 回声测深仪5.log 计程仪6.master (slave) clock 母（子）钟7.radar 雷达8.radio direction finder 无线电测向仪9.Loran (radio navigation / satellite navigation) receiver劳兰（无线电导航/ 卫星导航）接收机10.V HF radio telephone transceiver 甚高频电话收发信机11.f acsimile 传真机12.t elevision set 电视机13.v ideo camera 电视摄像机oxygen 氧气acetylene 乙炔nitrogen 氮气inter gas 惰性气体epoxy 环氧的resin 树脂chock楔子垫木soapy water 肥皂水anemometer 风速计manometer 压力（压强）表，气压表straight edge 直尺feeler gauge 塞尺steel scale 钢尺dial gauge 千分表micrometer 外径千分尺vernier caliper 游标卡尺spanner 扳手wrench 扳手screw driver 螺丝刀hammer 锤子clinometer 测斜仪chain block 手拉葫芦mandatory 命令、强制的Chlorinator 氯化器syphon=siphon 弯管，存水管，虹吸管blind 盲板booklet of piping procedure 工序，过程，步骤gymnasium 健身房galley 船上厨房motorcycle safety helmet 安全帽life belt 安全带glove 手套respirator 口罩overall 工作服uniformelectric torch 手电筒flashlighteyeglass 眼镜elevator 电梯plank 厚木板stage 大舞台Slipway、shipway船台1.Lighting alignment for shafting & rudder system 轴舵系照光对中2.Stern tube boring 艉轴管镗孔3.Stern tube bush 艉轴衬套4.Stern boss艉轴壳5.forced fitting inspection压入配合检验6.oil jack（千斤顶）油泵7.（propeller shaft & stern tube bush）radial clearance （艉轴和艉管衬套）径向间隙8.axial clearance 轴向间隙9.Stern tube seals sealing 艉轴密封10. propeller installation force fitting压配11.pull-up length压进距离12.pull-up force 推进力13.oilpressure for boss 扩涨油压14.Zero point 零点15. Shrinkage 过盈量16.cleanness光洁度17.taper圆锥，斜度18. superposition 重合19. intersect 相交20.perpendicularity 垂直度21.vertical垂直的22.horizontal 水平的23. nut of stern shaft艉轴螺栓24.rudder 舵25.rudder blade 舵叶26.rudder stock 舵杆27.rudder pintle 舵销28.rudder tiller 舵柄29.rudder bush 舵承30.rudder horn 挂舵臂31. securing key 定位销，定位键32.protecting cover 保护帽33.grease牛油34.rudder angle 舵角35.full angle 满舵36. rudder blade’s stopper防跳块37.temperature sensor 温度传感器38. inlet outlet 进出39. tolerance 公差，允许量40.wear down gauge 磨损规41.stern tube main chamber 大腔42.high pressure chamber 高压腔43.low pressure chamber 低压腔Engine Room 机舱1.Cleaning check：Storage oil tank of steering gear 舵机储存油箱（方形）Expansion oil tank of mooring winch 绞机膨胀油箱（圆形）Storage oil tank of mooring winch 绞机储存油箱Storage oil tank of windlass 锚机储存油箱（方形）Expansion oil tank of windlass 锚机膨胀油箱（圆形）Hydraulic oil tank of hatch cover 舱口盖液压油箱2.flushing of winch piping 绞机管路投油1.D/G pouring epoxy chock 发电机浇环氧2.holding down bolt 地脚螺栓3.deflection of crankshaft 曲轴甩档4.piston 活塞5.cylinder 气缸6. turbocharger 涡轮增压器7.1.Force measurement of M/E stay bolts 紧固螺栓2.piston rod and connection rod bolts 活塞杆和连杆螺栓3.bolts in drive end of crank 曲轴大端螺栓4.piston—piston rod—crosshead—connection rod—crank—crankshaft活塞活塞杆十字头连杆曲柄曲轴5.cam 凸轮6.camshaft 凸轮轴7.M/E chain cable 主机链条8.flooding test of M/E return oil pipes 压水试验9.propeller cap—propeller—stern tube seals—stern tube bush—sternshaft—intermediate shaft导流帽螺旋桨艉密封艉管衬套艉轴中间轴—intermediate bearing—flywheel (thrust shaft)中间轴承飞轮推力轴10.coupling reamer holes 联轴节铰制孔11.turning gear 盘车机12. spring 弹簧1.main air compressor主空压机2.alignment of coupling flange 联轴节对中3.gap 裂面4.sag 位移1.steering gear舵机2. ram roller bearing 舵机活塞杆轴承3. neck bush & cylinder 舵机活塞颈衬套和活塞缸体4. dimension measurement 尺寸测量1.fore draft valve艏吃水阀2.speed log 计程仪3.echo sounder 测深仪Quay、shipside、wharf、dock码头。
船舶轮机专业词汇
第一部分柴油机DIESEL ENGINE1、二冲程柴油机two stroke marine diesel engine2、四冲程柴油机four stroke marine diesel engine3、高（中、低）速柴油high（medium，lower）speed engine4、汽缸cylinder5、汽缸盖cylinder cover（cylinder head）6、汽缸体cylinder body（block、jacket）7、汽缸套cylinder liner8、示功阀indicator cock9、示功阀indicator valve10、汽缸启动阀cylinder air starting valve11、缸套顶圈head ring for cylinder liner12、排气阀exhaust valve13、进气阀air inlet valve（suction valve）14、气阀传动机构valve driving mechanism15、顶杆tappet rod16、推杆push rod18、摇臂rocker rod（rocker lever）19、活塞piston20、十字头式活塞crosshead type piston21、筒型活塞trunk piston22、活塞头piston crown（head）23、活塞裙piston skirt24、活塞体piston body25、活塞销piston pin（gudgeon pin）26、活塞环piston ring27、气环（压缩环）compression ring28、刮油环oil scraper ring（oil ring、scraper ring）29、布油环oil distributing ring30、耐磨环wear ring31、活塞环槽piston ring groove32、活塞冷却水管piston cooling pipe33、往复管reciprocating pipe34、伸缩管telescope pipe35、铰链管articulate pipe36、活塞杆piston rod37、活塞杆凸缘piston rod flange38、活塞杆填料函stuffing box for piston rod39、活塞杆填料箱gland box for piston rod （Packing gland for piston rod）40、填料函壳体stuffing box casing41、填料函张力弹簧tension spring for stuffing box42、填料函密封环sealing ring for stuffing box43。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
4船舶英语目 录一.职位及工种(Titles and type of work) ····· 1 二、柴油机类(Words about diesel engine) ····· 3 三、船舶机械类(Words about marine machinery) ·· 11 四、阀门(Words about valve) ···· 14 五、泵类(Words about pump) ·········· 16 六、甲板机械类（Deck machinery） ······ 18 七、工具类(Word about tools) ········ 20 八、常用物料(Material in common use) 26 九、常用紧固件(Part of fixation in common use) ··· 28 十、常用油类(Oil in common use) ·····28 十一、常用量词(Quantifier in common use) ·········29 十二、国家名称(Name of country) 。
30 十三、常用缩语(abbreviation in common use) ·····31 十四、船用动态常用单词(marine tends word) 32十五、船舶机电设备操作词汇(manipulate of marine equipment) ·33 十六、故障常用单词(words about malfunction) ····· 35 十七、保养检修常用词汇(Words about maintain and examination) 38 十八、常用数字(Numeral in common use) 40 十九、时间、季节与方向(Time、Season and Direction) ·····42 二十常用词组（Phrases in common use） ·45 二十一、常用动词和例句(Verb in common use and example) ····48 二十二、问候和常用表达语(Greeting and common expression) ····67 二十三、主机提交过程用语(Delivery expressions for main engine) 68 二十四、空压机和空气系统用语(Air compressor and Air system) ···· 75 二十五、锅炉提交用语(Delivery expressions for boiler) ···77 二十六 、 锚绞车提交过程用语 (Delivery expressions for anchor windlass) 79 二十七、舵机提交过程用语(Steering gear delivering) ··· 87 二十八、付机提交过程用语（Delivery expression for A/E） ····· 91 二十九、救生艇提交过程用语(Delivery expressions for lifeboat) ··92 三十、其他提交项目(Delivery expressions for other items) (95)三十一、甲板机械系泊试验(Mooring test for deck machinery) (96)三十二、机舱设备系泊试验(Mooring test for the equipment in E/R) (98)三十三、谈论故障常用语（Expressions for trouble） ············100 三十四、谈论检修常用语(Expressions for overhaul) ············ 101 三十五、谈论试验和检验 (Talking about test & check) ···········103 三十六、谈论技术要求(Talking about technology required) (105)一．职位及工种(Titles and type of work)1．船长 Captain 2．大副 Chief officer 3．二副 Second officer 4．三副 Third officer 5．四副 Fourth officer 6．水手长 Boatswain 7．水手 Sailor & Seaman 8．木匠 Carpenter 9．轮机长 Chief engineer 10．大管轮 Second engineer 11．二管轮 Third engineer 12．三管轮 Fourth engineer 13．机匠长 Chief motorman 15．机匠 Fitter 16．加油工 Oil man 17．大电 Chief electrician 18．电工 Electrician 19．车间主任 Workshop director 20．工长 Section chief 21．班长 Fore man 22．钳工 Fitter23．主管工程师 Engineer in charge 24．机务 &船东 Superintendent &Super &Owner25．助理工程师 Assistant engineer 26．验船师（机）Register 27．验船师（船）Surveyor 28．油漆工 Painter 29．焊工 Welder 30．大橱 Chief cook 31．物料员 Store keeper 32．加油工 Oiler 33．机工 Mechanic 34．甲板员 Deck man 35．电线工 Wireman 36．外包工 Laborer 37．铸工 Molder 38．管子工 Pipe fitter 39．起重工 Crane operator二、柴油机类(Words about diesel engine) 1．主机 Main engine2．二冲程柴油机 Two-stroke diesel engine 3．四冲程柴油机 Fore-stroke diesel engine 4．高速柴油机 High speed diesel engine 5．中速柴油机 Middle speed diesel engine6．低速柴油机 Low speed diesel engine 7．气缸盖(缸头) Cylinder head 8．安全阀 Safety valve 9．释放阀 Relief valve 10．示功阀 Indicator valve 11．示功考克 Indicator cock 12．空气起动阀 Air starting valve13．起动空气分配器 Air starting distributor 14．油头(燃油喷射器) Fuel injector 15．排气阀 Exhaust valve 16．气缸套 Cylinder liner 17．冷却水套 Cooling water jacket 18．气缸注油器 Cylinder lubricator 19．活塞 Piston 20．活塞头 Piston crown 21．活塞裙 Piston skirt 22．活塞销 Piston gudgeon pin 24．活塞杆 Piston rod 25．活塞环 Piston ring 26．活塞环槽 Piston ring groove27．压缩环 (气环) Compression ring28．刮油环 (油环) Oil scraper ring 29．减磨令 Wear ring (copper ring) 30．伸缩管(水拉管) Telescopic pipe 31．活塞冷却空间 Piston cooling space 32．填料箱(函) Stuffing box33．填料箱密封环 Sealing ring for Stuffing box34．填料箱压缩环 Pressure ring for Stuffing box35．填料箱刮油环 Scraper ring for Stuffing box36．扫气箱 Scavenging receiver 37．扫气口 Scavenging port 38．排气口 Exhaust port 39．十字头 Cross head 40．十字头销 Crosshead pin41．十字头轴承 Crosshead bearing 42．十字头滑块 Crosshead slipper 43．滑块 Guide shoe44．十字头导板 Crosshead guide plate 45．连杆 Connecting rod 46．连杆大端轴承 Bid end bearing 47．连杆小端轴承 Small end bearing 48．曲柄轴承 Crank bearing 49．曲柄销 Crank pin 50．曲轴 Crank shaft 51．曲轴颈 Crank journal 52．曲柄臂 Crank web 53．拐档差 Crank deflection 54．主轴承 Main bearing 55．主轴颈 Main journal 56．轴承瓦 Bearing bush 57．上轴瓦 Upper bearing bush 58．上轴瓦 Upper half 59．下轴瓦 Lower bearing bush 60．下轴瓦 Lower half 61．推力轴承 Thrust bearing 62．推力块 Thrust pad 63．推力盘 Thrust disc 64．推力轴 Thrust shaft 65．底座 Bed plate 66．机架 Frame 67．曲柄箱 Crank case68．曲柄箱导门 Crank case door69．曲柄箱防爆门 Explosion-proof Crank case.70．定时齿轮 Timing gear 71．飞轮 Flying wheel 72．凸轮 Cam 73．凸轮轴 Cam shaft 74．喷油凸轮 Fuel injection cam 75．链条 Chain 76．链条轮 Chain wheel 77．链条箱 Chain box 78．推杆 Push rod 79．摇臂 Rocker arm 80．排气阀 Exhaust valve 81．吸气阀 Suction valve 82．排气总管 Exhaust manifold 83．进气总管 Air inlet manifold84．高压燃油管 High pressure fuel pipe 85．活塞冷却水管 Piston cooling water pipe 86．法兰 Flange 87．贯穿螺栓 Tie bolt (tie rod) 88．端盖 Side cover 89．滑油泵 Lubricating oil pump 90．燃油泵 Fuel oil pump91．滑油泵齿轮 Gear for lubricating oilpump92．燃油泵齿轮 Gear for fuel oil pump 93．叶轮 Impeller94．柱塞 Plunger95．导杆 Guide rod96．导套 Sleeve97．滚动轴承 Ball bearing98．滑动轴承 Sliding bearing99．推力滚动轴承 Thrust ball bearing 100．推力面 Thrust surface (thrust side)101．盘车机 Turning gear102．增压器 Turbocharger103．涡轮机(透平) Turbine104．涡轮 Turbine wheel105．涡轮叶片 Turbine blade106．喷嘴 Nozzle107．废气叶轮 Exhaust impeller108．废气叶轮片 Exhaust blade109．废气端 Exhaust side110．透平端 Turbine side111．转子轴 Rotor shaft112．油泵 L.O.pump113．换向装置 Reversing device114．换向伺服期 Reversing servomotor 115．压气机(鼓风机) Blower116．膨胀接 Expansion joint117．调速器 governor118．飞重 Flying weight119．补偿阀 Compensate valve120．针阀 Needle valve121．开口销 Cotter pin122．轴封 Shaft seal123．机械密封 Machinery seal124．配电盘 Switchboard125．应急配电盘 Emergency switchboard 126．应急发电机 Emergency generator 127．滤器 Filter128．细滤器 Filter129．粗滤器 Strainer130．滑油滤器 L.O. filter131．燃油滤器 F.O. filter132．空气消音器 Air intake silencer 132．空气滤器 Air intake filter 133．空气瓶 Air bottle (receiver) 134．分油机 Separator135．油水分离器 Water-oil separator 136．净油机 Purifier137．燃油净化器 F.O. purifier138．二氧化碳 CO2139．二氧化碳瓶 CO2 bottle140．正时齿轮 Timing gear141．导向棒装置 Guide bar142．注油器驱动 Lubricator driver 143．链条张紧装置 Chain tightener144．凸轮轴传动轮 Chain wheel on cam shaft 145． 中间链链传动轮 Intermediate chain wheel 146．注油器驱动装置 Lubricator drive 147．链条张紧装置 Chain tightener148．滚筒导座 Roller guide housing 149．应急操纵台 Emergency console 150．力矩平衡器 Moment compensator 151．主启动阀 Main starting valve 152． 启动空气分配器 Starting air distributor 153．喷油器 Fuel valve154．扫气系统 Scavenge air system 155．安全帽 Safety cap156．机座 Bed plate157．轴向振动减振器 Axial vibration damper 158．贯穿螺栓 Arrangement of staybolt159．示功器驱动装置 Indicator driver160．端罩 End shields161．气缸架 Cylinder frame162．气阀传动装置 Valve operating device163．摇臂润滑油泵 Rocker arm lubricatingoil pump164．摇臂润滑油柜 Rocker arm lubricatingtank165．摇臂润滑滤器 Rocker arm lubricatingfilter三、船舶机械类(Words about marinemachinery)1．船用锅炉 Marine boiler2．废气锅炉 Exhaust boiler3．辅锅炉 Donkey boiler4．组合式锅炉 Combined boiler5．火管 Fire tube6．给水管 Feed pipe7．炉膛 Furnace8．炉墙 Furnace wall9．火侧 Fire side10．水侧 Water side11．燃烧器 Oil burner12．安全阀 Safety valve13．上排污 Upper drain14．下排污 Lower drain15．锅炉皮阀 Mounting valve16．水位计 Water level gauge17．压力表 Pressure gauge18．主汽门 Main steam valve19．玻璃管 Glass tube20．空调装置 Air-conditioning plant21．制冷装置 Refrigerating plant22．冰机 Fridge. Machine23．空气压缩机 Air compressor24．造水机 Fresh water generator25．板式冷却器 Plate type cooler26．机舱天车 Engine room crane27．天车导轨 Crane rail28．电磁阀 Solenoid valve29．舵机 Steering gear30．舵承 Rudder bearing carrier31．液压缸 Hydraulic cylinder32．废气涡轮增压器 Exhaust gas turbocharger33．弹簧阀 Spring loaded valve34．冷凝器 Condenser35．分油器 Oil separator36．轴带发电机 Shaft generator37．焚烧炉 Oil burner38．分油机 Separator39．分离筒 Separator bowl40．配水盘装置 Paring disc device41．转数计 Revolution counter42．控制阀 Control valve43．辅机 Auxiliary machinery44．制冷装置 Refrigerating plant45．海水淡化装置 Sea water desalting plant46．热交换器 Heat exchanger47．船用气瓶 Marine air bottle48．冷风机 Cooler unit49．防水风门 Fire damper50．气密挡板 Gas tight damper51．排气风机 Exhaust fan52．舱室通风机 Cabin fan53．机舱通风机 Engine room fan54．应急鼓风机 Emergency blower四、阀门(Words about valve)1．吸气阀 Suction valve2．排气阀 Exhaust valve3．控制阀 Control valve4．导 阀 Pilot valve5．单向阀 Non-return valve6．口琴阀 Flap valve7．调节阀 Regulating valve8．液压阀 Hydraulic valve9．膨胀阀 Expansion valve10．给水阀 Feed valve11．排水阀 Discharge valve12．截止阀 Stop valve13．吹泄阀 Blow-off valve14．空气阀 Air valve15．泄放阀 Drain valve16．止回阀 Check valve17．海底阀 Sea valve18．回流阀 Retune valve19．节流阀 Throttle valve20．进气阀 Inlet valve21．出气阀 Outlet valve22．热力阀 Thermal valve23．中央阀 Center valve24．单向阀 One way valve25．二通阀 Two way valve26．三通阀 Triple valve27．旁通阀 By-pass valve28．换向阀 Change-over valve29．减压阀 Pressure-reducing valve30．溢流阀 Overflow valve31．自闭阀 Self-locking valve32．针阀 Needle valve33．平衡阀 Balance valve34．循环阀 Circulation valve35．主 阀 Main valve36．滑 阀 Slide valve37．蝶 阀 Butter-fly valve38．截止阀 Shut-off valve39．闸板阀 Gate valve40．通海阀 Sea suction valve41．吹除阀 Sea chest cleaning valve42．防浪阀 Storm valve43．舱壁阀 Bulkhead valve44．快关阀 Emergency shut off valve45．呼吸阀 Breather valve五、泵类(Words about pump)1．电动泵 Motor-driven pump2．柱塞泵 Plunger pump3．叶片泵 Vane pump4．回转泵 Rotary pump5．齿轮泵 Gear pump6．往复泵 Reciprocating pump7．离心泵 Centrifugal pump1．电动泵 Motor-driven pump2．柱塞泵 Plunger pump3．叶片泵 Vane pump4．回转泵 Rotary pump5．齿轮泵 Gear pump6．往复泵 Reciprocating pump7．离心泵 Centrifugal pump8．真空泵 Vacuum pump9．螺杆泵 Screw pump10．喷射泵 Ejector pump11．冷却泵 Cooling pump12．淡水泵 Fresh water pump13．海水泵 Sea water pump14．给水泵 Feed water pump15．循环泵 Circulating pump 16．锅炉给水泵 Boiler feed pump 17．卫生水泵 Sanitary pump18．压载泵 Ballast pump19．舱底泵 Bilge pump20．污水泵 Sewage pump21．燃油泵 Fuel pump22．高压油泵 High pressure pump 23．底压油泵 Low pressure pump 24．驳运泵 Transfer pump25．增压泵 Booster pump26．消防泵 Fire pump27．通用泵 G.S. pump28．旋涡泵 Regenerative29．蜗壳泵 Volute pump30．导叶泵 Diffuser pump31．单联泵 Simplex pump32．双联泵 Duplex pump33．多联泵 Multiplex pump 34．活塞泵 Piston pump35．减摇泵 Anti-roll pump 36．总用泵 General service pump 37．应急消防泵 Emergency fire pump 38．扫舱泵 Stripping pump 39．货油泵 Cargo oil pump 40．滑油泵 Lubricating oil pump六、甲板机械类（Deck machinery）1．锚机 Windlass2．锚机轴 Windlass shaft3．刹车带 Brake lining4．离合器 Clutch5．锚链轮 Anchor Chain wheel 6．轴承瓦 Bearing bush7．轴承盖 Bearing cover8．绞揽机 Capstan9．系揽绞车 Mooring winch10．卷缆车 Reel11．钢丝绳 Wire rope12．卡环 Shackle13．缆绳 Mooring rope14．滑轮 Block15．刹车装置 Brake device16．制链器 Anchor chain stopper 17．舱盖滚轮 Hatch cover wheel 18．舱盖铰链 Hatch cover hinge 19．液压油缸 Hydraulic jack20．起货机 Cargo winch21．可令吊 Crane22．生活吊 Accommodation crane 23．吊杆 Derrick boom24．桅杆 Mast25．救生艇 Lifeboat26．艇架 Davit27．艇机 Lifeboat capstan 28．救生筏 Life raft29．救生衣 Life jacket七、工具类(Word about tools)1．车床 Lathe2．刨床 Planing machine 3．钻床 Drill machine4．砂轮机 Grinding machine 5．磨床 Grinder6．铣床 Milling machine 7．镗床 Boring machine8．手锤 Engineer’s hammer 9．冲击板手 Impact wrench10．板手 Spanner 11．活络板手 Screw spanner12．梅花板手 Ring spanner13．呆扳手 Open spanner15．套筒板手 Socket spanner16．管子钳 Pipe spanner17．螺丝刀 Screw driver18．钢丝钳 Wire pliers19．尖嘴钳 Long nose pliers20．钢锯 Hack saw21．剪刀 Scissors22．手电筒 Torch23．扁铲(凿子) Chisel24．锉刀 File25．丝攻 Thread tap26．板牙 Thread die27．绞刀 Reamer28．刮刀 Scraper29．油石 Oil stone30．拔子(拉马) Puller31．沙布 Emery cloth32．破布 Rag33．卷尺 Measuring tape34．空心冲 Hole punch35．样冲 Joint punch36．油壶 Oil gun37．牛油枪 Grease gun38．手电钻 Handle drill39．钻头 Drill40．液压千斤 Hydraulic jack.41．塞尺 Feeler gauge42．游标卡尺 Vernier caliper43．外卡尺 Outside calipers44．内卡尺 Inside calipers45．螺纹量规 Screw gauge46．桥规 Bridge gauge47．电焊机 Electrode welding machine48．气焊机 Gas welding machine49．电焊钳 Electric welding pliers50．气割枪 Cutting touch51．电焊条 Electric soldering iron52．电工刀 Electrician knife53．电笔 Test pen54．剥线钳 Wire stripping pliers55．圆规 Compass56．量表 Gauge57．拐档表 Crank deflection gauge58．深度规 Depth gauge59．千分表 Micrometer gauge60．台虎钳 Table vice61．柴油 Diesel oil62．滑油 Lubricating oil63．液压油 Hydraulic oil64．重油 Heavy oil65．燃油 Fuel oil66．黄油 Grease67．螺栓 Bolt68．螺帽 Nut69．垫片 Washer70．研磨沙 Grinding sand71．研磨膏 Grinding paste72．石棉板 Asbestos plate73．青壳纸 Fish paper74．盘根 Packing75．细钢丝 Thin steel wire76．密封圈 Rubber seal ring77．塑料管 Plastic pipe78．胶皮管 Rubber hose79．电灯泡 Electric bulb80．工作灯 Working lamp81．插头 Electric plug82．插座 Electric socket.93． 喷砂机 Sand blaster outfit94． 空气马达 Air motor95．油柜清洁器 Tank cleaning machine96．高压冲水机 High pressure hose forhydraulic97．真空泵 Vacuum pump98．套筒扳手组 Socket wrench set99． 深头套筒 Deep socket wrench100．套筒扳手 Box wrench101．单开口扳手 Single open end wrench102．双开口扳手 Double open end wrench103．转矩扳手 Torque wrench104．电动机扳手 Motor wrench105．侧剪钳 Slide cutting plier106．活节钳 Combination plier107．可调快速扳手 Speed wrench108．螺丝起子 Screwdriver109．偏向螺丝起子 Offset screw110．六角螺帽起子组 Hexagon nut drivers set111．手摇钻 Straight hand drill112．手工锯 Hacksaw frame113．锯片 Hacksaw blade114．砂纸 Silicon paper115．手拉葫芦 Chain block116．高压管 High pressure hose117．液压千金顶 Hydraulic jack118．锤子 Hammer119．平錾 Cold chisel120．活动扳手 Adjustable wrench121．螺丝刀 Screwdriver122．侧剪铗 Side cutting hipper123．螺栓剪 Cable cutter124．敲击管钳 Rap wrench125．砂轮 Grinding wheel126．老虎钳 Utility vise127．直梯 Straight ladder128．踏梯 Step ladder129．平台推车 Platform trunk130．搬平车 Gas cylinder carrier131．给油机 Grease lubricator132．强力油泵 Heavy duty pump oiler133．油壶 Oil jag134．麻花钻 Twist drill135．绞刀 Pin reamer136．旋转中心钻 Rolling center137．外径测微计 Outside micrometer withcounter138．六折式尺 Six-folding rule139．弹性带尺 Convex rule140．不锈钢直尺 Stainless steel straightrule141．平面规 Surface gauge142．平行直角定规 Precision flat try square143．温度计 Thermometer八、常用物料(Material in common use)1．阀研磨剂 valve grinding compound2．电焊条 steel electrode3．气焊条 Steel welding wire4．细钢丝绳 Seizing wire5．刚焊条 Steel welding rod6．紫铜管 Copper tube7．乙炔气瓶 Acetylene cylinder8．木屑 Saw dust9．水泥 Cement10．石灰 Lime11．帆布手套 Canvas glove12．垫片 Gasket.13．氧气瓶 Oxygen cylinder14．抹布 Rag15．垫隙片 Shim16．电线 Wire17．电缆 Electric cylinder18．电池 Rag19．灯泡 Bulb20．胶布 Insulating tape21．插头 Plug22．插座 Socket23．保险丝 Fuse24．不锈钢 Stainless steel25．铸铁 Cast iron26．黄铜 Brass27．青铜 Bronze28．铝合金 Aluminium alloy29．橡胶 Rubber30．石棉 Asbestus31．低碳钢 Soft steel32．高碳钢 High-carbon steel33．合金钢 Alloy steel34．木材 Wood35．塑料 Plastic36．球墨铸铁 Nodular iron九、常用紧固件(Part of fixation in common use)1．螺栓 Bolt2．螺丝 Screw3．螺母 Nut4．方头螺栓 Sq head bolt5．埋头螺栓 Counter sunk head screw 6．套筒螺栓 Socket head bolt7．定位螺栓 Set screw8．十字接头 Cross9．锥形销 Taper pin10．锁紧螺母 Lock nut11．六角头螺栓 Hex head bolt十、常用油类(Oil in common use)1．汽油 Gas oil2．煤油 Kerosene3．润滑油 Lubricating oil4．汽缸油 Cylinder oil5．压缩机油 Compressor oil6．齿轮油 Gear oil7．机油 Motor oil8．凡士林 Vaseline9．燃油 Fuel oil10．油脂 Grease11．柴油 Diesel oil十一、常用量词(Quantifier in common use) 1． 件，只，个 Piece2． 条，张，片 Sheet3． 双 Pair4． 套，组，副 Set.5． 盒 Box6． 箱 Case7． 瓶 Bottle8． 米 Meter9． 厘米 Centimeter10．毫米 Millimeter11．公斤 Kilogram12．克 Gram13．公升 Liter14．平方 Square15．袋 Bag16．码 Yard 17．吨 Ton18．磅 Pound19．加仑 Gallon20．立方 Cubic十二、国家名称(Name of country)1．中国 China2．美国 American3．日本 Japan4．英国 Britain5．法国 France6．德国 German7．韩国 South Korea8．希腊 Greece9．泰国 Thailand10．印度 India11．挪威 Norway12．俄罗斯 Russia13．新加坡 Singapore14．澳大利亚 Australia15．伊朗 Iran16．丹麦 Denmark17．加拿大 Canada18．丹麦 Denmark19．芬兰 Finland20．巴基斯坦 Pakistan21．意大利 Italy十三、常用缩语(abbreviation in common use)1．主机 M/E2．付机 A/E3．阀 V/V4．泵 P/P5．备车 St/by6．完车 F.W.E.7．前进三 FAHD8．微速后退 D.S.Ast9．前进二 H.Ahd10．高压 H.P.11．低压 L.P.12．重油/柴油 H.O./D.O.13．前后 F/A14．左舷 P: port15．无人机舱 UMS16．自动 Auto17．气缸 Cyl18．燃油柜 19．滑油柜 20．沉淀柜 .21．排出 Disc22．吸入 Suct23．柴油柜 十四、船用动态常用单词(marine tends word)1．停靠 Alongside2．接近 Approach3．停泊 Berth4．浮筒 Buoy5．码头 Pier6．港口 Port7．移泊 Shift8．航次 Voyage9．试验 Try10．值班 Watch11．航行 Sail十五、船舶机电设备操作词汇(manipulate of marine equipment)1．调整 Adjust2．压载 Ballast3．转换 Change over4．清洁 Clean5．联接 Connect6．排放压载 Deballast7．放残水 Drain8．卸载 Off9．油漆 Paint10．接通 Put on11．吹灰 Soot blown12．开始 Start13．顶端 Top14．洗 Wash15．吹 Blow16．检查 Check17．铲 Chip18．断开 Cut out19．排放 Discharge20．除垢 Descale21．检验 Examine22．受载 On(load)23．用泵排出 Pump out24．调整 Set25．停止 Stop26．调驳 Transfer27．加满 Top up十六 、 故障常用单词 (words aboutmalfunction)1．失常的 Abnormal2．烧坏 Burn3．堵塞 Clog4．裂缝 Crack5．变形 Deform6．毁坏 Destroy7．磨损 Wear8．出故障 In trouble9．敲击 Knock10．松开 Loose11．不对中 Misalign12．不足的 Insufficient13．失灵 Out of order14．过载 Overload15．过度磨损 Over-worn16．尺寸过大 Oversized17．尺寸过小 Under-sized18．振动 Vibrate19．不平的 Uneven20．不准确 Inaccurate21．全船断电 Black out22．出故障 Fail23．关掉 Shut off24．弯曲 Bend25．停车 Break drown26．腐蚀 Corrode27．腐蚀的 Corrosive28．损坏 Damage29．有毛病的 Faulty30．有缺陷的 Defective31．破裂 Fracture32．卡住 Jam33．漏泄 Leak34．漏泄的 Leaky35．融化 Melt36．噪声 Noise37．过热 Overheat38．咬住 Seize39．紧的 Tight40．松的 Loosen41．发现 Find42．停止 Stop44 43．脏的 Dirty 44．油污的 greasy45．失效的 ineffective 46．椭圆形的 oval 47．点不着火 misfire 48．接错 misjoin 49．放错 misplace 50．老化 perish 51．麻点 pit 52．凸起 ridge 53．划伤 score 54．拉痕scuff十七、保养检修常用词汇 (Words about maintain and examination) 1．卡死 Blind 2．用卡钳量 Caliper 3．关闭 Close 4．解体 Disassemble 5．安装 Fix 6．组装 Box up 7．检验 Check 8．拆卸 Dismantle 9．装配 Fit 10．紧固 Fasten 11．测量 Gauge 12．安装 Install 13．测量 Measure 14．打开 Open 15．上油漆 Paint 16．换新 Renew 17．上紧 Tighten 18．洗 Wash 19．涂油脂 Grease 20．松开 Loosen 21．加油 Oil 22．检修 Overhaul 23．重新组装 Reassemble 24．测取读数 Take reading 25．拧开螺栓 Unbolt 26．抽出 Withdraw 十八、常用数字(Numeral in common use) 一 One 二 Two 三 Three 四 Four 五 Five 六 Six 七 Seven 八 Eight 九 Nine 十 Ten 十一 Eleven 十二 Twelve 十三 Thirteen 十四 Fourteen 十五 Fifteen 十六 Sixteen 十七 Seventeen 十八 Eighteen十九 Nineteen 二十 Twenty 三十 Thirty 四十 Forty 五十 Fifty 六十 Sixty 七十 Seventy 八十 Eighty九十 Ninety 百 Hundred 千 Thousand 万 Ten thousand 百万 Million 第一 First 第二 Second 第三 Third 第四 Fourth 第五 Fifth 第六 Sixth 第七 Seventh 第八 Eighth第九 Ninth第十 Tenth 第十一 Eleventh 第十二 Twelfth 第二十 Twentieth 十九、时间、季节与方向 (Time、Season and Direction) 1．星期一 Monday 2．星期二 Tuesday 3．星期三 Wednesday 4．星期四 Thursday 5．星期五 Friday 6．星期六 Saturday 7．星期日 Sunday 8．春季 Spring 9．夏季 Summer 10．秋季 Autumn 11．冬季 Winter 12．一月 January 13．二月 February 14．三月 March 15．四月 April 16．五月 May 17．六月 June 18．七月 July 19．八月 August 20．九月 September21．十月 October22．十一月 November 23．十二月 December 24．小时 Hour 25．分钟 Minute 26．秒 Second 27．月 Month 28．天 Day 29．夜 Night 30．周 Week 31．早晨、上午 Morning 32．下午 Afternoon 33．傍晚 Evening 34．正午 Noon 35．今天 Today 36．昨天 Yesterday 37．明天 Tomorrow 38．前天 The day before yesterday 39．后天 The day after tomorrow40．本周 This week41．上周 Last week42．下周 Next week 43．九月十日 Sep.10 th 44．去年 Last year 45．明年 Next year 46．上周二 Last Tuesday 47．下周一 Next Monday 48．东 East 49．西 West 50．南 South 51．北 North52．西北 Northwest 53．东北 Northeast 54．东南 Southeast 55．西南 Southwest 56．世纪Century二十、常用词组（Phrases in common use）1．发现已无法修复 found beyond repair2．发现尺寸过大found over-sized 3．发现反应缓慢 found slow function 4．发现不正常 found out of order 5．发现不合标准 found not up to standard 6．发现不准确 found inaccurate 7．发现失去作用 found out of function 8．发现轧住 found seized 9．发现过热 found overheated 10．发现过度磨损 found excessive wear 11．发现过度磨掉 found worn out12．发现有一点倾斜 found a little bit inclined13．发现不正常 found abnormal14． 发现因过热而损坏 found destroyed byoverheating15．发现龟裂 found chapped 16．发现塌陷 found collapsed17．发现运转失灵 found out of operation 18．发现呈椭圆形 found oval 19．发现拉痕 found scored 20．发现拉毛 found scuffed 21．发现变形 found deformed 22．发现松动 found loose 23．发现油污 found greasy 24．发现肮脏 found dirty 25．发现咬住 found stuck 26．发现挤压 found squeezed 27．发现弯曲 found bent 28．发现故障 found faulty 29．发现损坏 found damaged30．发现破碎成片 found broken to pieces 31．发现部分剥离 found partly detached 32．发现部分堵塞 found partly choked33．发现剧烈震动 found violent vibration 34．发现烧坏 found burnt 35．发现断裂 found fractured 36．发现接地 found earthed 37．发现敲缸 found knocking 38．发现溶化 found melted away 39．发现泄漏 found leaking (found leaky)40．发现冻结 found stuck fast by icing41．发现锈蚀 found rusty 42．发现失效 found ineffective 43．发现故障 found out of order 44．发现结霜 found frosted 45．发现丢失 found lost 46．发现出故障 found in trouble 47．发现失灵 found out of order 48．发现失灵 found out of action 49．发现不一致 found out of operation 50．发现错位 found out of place 二十一、常用动词和例句(Verb in common use and example) 1．借 borrow我要向你借这份图纸I want to borrow the drawing from you.我可以向你借这个手锤吗?May I borrow the hammer from you?2．裂 break阀杆断裂了The valve spindle is broken.滚动轴承断裂成碎片了The ball bearing are broken to pieces. 3．加强 build up叶轮应该堆焊The impeller should be built up by welding.4． 烧 burn电动机烧了 The motor is burnt.5． 进行 carry out应进行负载试验The load test should be carried out. 6．吹 blow管子必须用压缩空气吹清The pipe should be blown with compressed air.7．铸 cast按原样铸造一个 Cast one piece as per sample.8．引起 cause损坏是有剧烈振动引起的 The damage was caused by violent vibration.9．倒角 chamfer油槽须倒角 Oil groove is to be chamfered.法兰切削后须倒角 The flange should be chamfered after being machined.10．换掉 change把它们换掉,否则我拒绝验收Have them changed, otherwise I refuse to accept them.11．龟裂 chap轴瓦上的白合金龟裂了 The white metal on the bearing bush is chapped.12．核查 check用桥规核查主轴承Check the main bearing with bridge gauge.修理前后要核查拐档 Check the crankshaft deflection before and after repair.13．清洁 clean装前须清洁 Clean it before fit back. 14．阻塞 clog燃油滤器阻塞了 The fuel filter is clogged.15．涂漆 coat用红丹涂管子 Coat the pipe with red lead.泵壳里涂防护漆 The pump casing is to be coated with anti-fouling.16．完成 complete finish你什么时候能完成修理工作?When can you complete (finish) the repair job?17．连接 connect把电动机和淡水泵连接起来Connect the motor with the fresh water pump18．腐蚀 corrode泵壳和叶轮均有腐蚀 The pump casing and impeller are corroded.19．盖 cover请把所有卸下的部件盖起来Please cover all the removed parts. 20．裂二号缸头裂开穿透至冷却水空间No.2 cylinder head is cracked.21．吊 crane把液压马达吊上岸去修理Crane the hydraulic motor ashore forrepair.22．割 cut把底座割掉Cut off the bedplate.23．损坏 damage滚动轴承严重损坏The ball bearings are seriously damaged.24．脱落 detach白合金部分脱落了The white metal is partly detached.25．查看 detect查看氟里昂系统有无泄漏Detect the Freon system for leakage.26．解体 disassemble解体,清洁并检查高压油泵 Disassemble,clean and check the H.P. fuel pump.27．脱开 disconnect把起动空气管脱开Disconnect the starting air pipe.将发电机与原动机脱开。