模具术语中英对照

模芯Parting Core
局部视图Partial View
冷料# Cold Slag
线切割Wire 轮廊Contour
螺纹孔Tapping Hole
连接件Fittings
斜针Angle Pin
接合Engage
替换镶件Interchangeable Mold Inserts
指定吨位的注塑机Specific Press
水嘴接头Water Fittings 螺纹Eyebolt Thread
回针Stop Pin
二级顶出针Sub-Leaderd Pin
镶件Mold Insert
加硬Harden
唧嘴Sprue 设计筒图Design
Preliminary
名称块表Title Block
版本标识Revision Level
材料清单Stock List
制模Build Mold
手动滑块Hand Slide
漏水测试Leak Test
流道排气Runner Vents
抛光Draw Polish
侧抽芯Side Action
加强筋Reinforcing
三角撑Gusset
柱子Bossed
出模斜度Draft
外廊Contour
落单会议Kick-Off
Meeting
装卸孔Handling Hole
运输安全带Moldstrap
码模槽Clamp Slot
撑头Support Pillar
螺牙1/2-13 Eye Bolt
1/2-13T ap
导柱位Leader Pin
Location
耐落胶Teflon Paste
偏移量Offset
水塞Water Line Plug
撬模脚Ppy Slot
重新加工Reworked
配件Components
补偿Compensation
平面度Parallel
倒角Chamfe
模胚Mold Base
热嘴Hotnozzle
火花机Edm
熔接线Weildline
压机Press
晒纹Texturing
梯形Trapezoid
凸缘、法兰Flange
方铁Spacer Block
顶针板Ejector Plate
顶针底板Ejector Retainer Plate
垫板Retainer Plate
后模镶针Core Pin
拉圾钉Stop Pin
有托顶针Shoulder Ejector Pin
顶针板导套Guided Ejection Bushing
针板导柱Guided Ejection Leader Pin
唧嘴Sprue Bushing
三板模延伸式唧嘴Extension Nozzle Bushing
水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring
管钉（定位销）Dowel Pin 管状管钉Tubular Dowel 吊环Safety Hoist Ring
日期印Dating Insert
环保印Recycling Insert
气顶Air Poppet Valve
截水口镶件Runner
Shut-Off Insert
早回Early Ejector Return
加速项Accelerated
Ejector
客户Client
产品名Part Name
产品编号Part No
缩水Shrinkage
版本Rev
模胚Mold Base
下模镶件Core Block
上模镶件Cavity Block
小镶件Sub-Insert
下模小镶件Core
Sub-Insert
上模小镶件Cavity
Sub-Insert
行位Slide
行位镶件Slide Insert
压条Gib
压紧块（铲机）Jaw
硬片（摩擦片）Wear Plate
水口铁Runner Bar
上模水口铁Upper
Runner Bar
下模水口铁Lower
Runner Bar
弹簧Spring
水口勾针Sprue Puller
Pin
顶针Ejector Pin
撑头Support Pillar
直身锁Side Lock
斜度锁Interlock
锁模板Safety Bar
‘O’令（密封圈）O'Ring
喉塞Plug
隔水片Baffle
波子螺丝（行位定位螺丝）
Ball-Catch
斜顶Lifter
控制开关Switch
回针Return Pin
斜导柱Angle Pin
推板Stripper Plate
A’板A'Plate
B’板B'Plate
方铁（垫铁）Spacer Block 顶针板Ejector Plate
顶针底板Ejector Retainer Plate
垫板Retainer Plate
垃圾钉Stop Pin
有托顶针Shoulder Ejector Pin
顶针板导套Guided Ejection Bushing
针板导柱Guided Ejection Leader Pin
唧嘴Sprue Bushing
三板模延伸式唧嘴Extension Nozzle
Bushing
水口板导套Runner
Stripper Plate Bushing
定位圈（法兰）Locating
Ring
管钉（定位销）Dowel Pin
管状管钉Tubular Dowel
吊环Safety Hoist Ring
日期印Dating Insert
环保印Recycling Insert
气顶Air Poppet Valve
截水口镶件Runner
Shut-Off Insert
早回Early Ejector Return
加速顶Accelerated
Ejector
扁顶Blade
出模斜波Draft
手动滑块模具Hand
Slide-In Type Mold
回针板Backup
合模Shutoff
空隙槽Clearance Slot
导柱及导套Leader Pin
Bushing
水口拉钩Spuer Puller
模框镶件Pocket Insert
成型热固性塑胶模具
Thermoset Mold
三板模3-Plat Mold
分型面Parting Line
司筒Ejector Sleeve
垫圈Washer
熔接线（夹水纹）Weldline
吸针Sucker Pin
回针板Retainer Plate
顶出板Knock -Out Plate
电动安全开关
Electrical-Safety Switch
脱开Cut Of Position
预先决定Preload
缓冲器Bumper
衬垫Cushion
公差Tolerance
突然性动作Slam
销针Dowel
钩槽Gib
精磨Finished
通框Through Window 粘后模Sticking Core
粘水口Sticking Sprue
夹水纹Weld Line
变形Warpage
走水不平均Filling Uneven
走不齐Short Shot
挂成品Part Hanging
漏水Water Leakage
刮花（擦伤）Galling
漏电Ele Leakage
困气Air Trapping
温度Temperature
注塑模Injection Mold 入水Gate
试板Sampling 压力Pressure
倒圆Fillet
顶棍Ejector
顶白Stress Mark
粘前模Sticking Cav
名称块表Title Block
版本标识Revision Level
材料清单Stock List
斜导柱（斜边）Angle Pin
A板A'plate
B板B'plate
倒扣Under-Cut
披峰Flash
缩水Sink Mark
氮化Nitride
不规则四边形Trapezoid
缩水Shrinkage
连续的Consecutive
雕刻Engrave
出模角Draft
分模面Parting Surface
擦位Shut-Off(S/0)
导套Bushing
回针Return Pin
加硬Harden
唧嘴Sprue
设计筒图Design
Preliminary
丝印Silkprint
不干胶Adhesive Sticker
导向针Guide Din
公差Tolerance
线切割Wire-Cut
电火花Edm
抛光Polishing
蚀纹Texture
探热针Thermocouple
三打螺丝毫（限螺丝）
Stripper Bolt
盖板Cover Plate
齿轮Gear
油唧Hydraulic Cylinder
司筒Ejector Sleeve
导柱Leader Pin
冷料# Cold Slag
线切割Wire 轮廓Contour
螺纹孔Tapping Hole
连接件Fittings
斜针Angle Pin
接合Engage
替换镶件Interchangeable Mold Inserts
指定吨位的注塑机Specific Press
水嘴接头Water Fittings 螺纹Eyebolt Thread
回针Stop Pin
二级顶出针Sub-Leader Pin
镶件Mold Insert
锁定位Lock
楔子(铲鸡) Wedge
高产量模量High Volume Running Mold 剖面图Cross Section
模具结构Mold Construction
模芯Parting Core
局部视图Partial View
热流道Manifold
热嘴Hot Nozzle
型腔数Cav No
模号Mold No
胶料Material
尺寸Dimension
重要尺寸Critical Dimension
雕刻Engrave
托司PIN。