锂离子电池英文共15页

锂离子电池技术英文词句

2.3 assembly line process(5/15)流水线工艺

film loading-vacuum on-film folding-sliding jig backward-top cutting-sliding jig forward-

vacuum off-film unloading

放上包装膜—抽真空—包装膜折叠-分切夹心的后端-剪掉顶部-分切夹心的前段-释放真空-拿下包装膜station 岗位two station 两个岗位

folding 折叠guide type 指导方式

top cutting 顶部剪切knife 刀片

2.3 assembly line process(6/15)流水线工艺

j/r loading-vacuum on-j/r jig backward-bottom former up-upper former down-

放极组-抽真空-极组夹具放在后端-模板末端在上面-顶端在下面-

heating forming-former up,down-j/r jig forward-vacuum off-j/r unloading

加热模板-模板上下翻转-极组夹具朝前-释放真空-取下极组

station two station

岗位两个岗位

heating forming pressing time,preset timer

加热模板施压时间施压次数

temperature thermocouple

温度热电耦

time:mmin,2~max.3sec

时间：

press force :40~50kg

压力

temperature:150℃

温度

2.3 assembly line process(7/15)流水线工艺

film loading-fim clamp-sliding jig backward-edge pushing-tab clamp-tab unclamp-

放上包装膜-包装夹具-分切极组末端-整边-放极耳夹具-卸下极耳夹具

sliding jig forward-cell unloading

分切极耳前端

station two station

heat sealing top

热封

sealing thickness control(micrometer)

热封厚度控制（毫米）

sealing control pressing time,preset timer

热封控制施压时间施压次数

precision regulator

精度校准

temperature, thermocouple

温度热电耦

time :min.2~max.3sec时间

press force:250kg

压力

temperature:180~250℃

温度

2.3 assembly line process(9/15)流水线工艺

cell loading-vacuum on-sliding jig backward-side cutting-feeding-tab cutting-

放上电芯-抽真空-滑动夹心后端-裁边-流入下工序-剪极耳

sliding jig forward-cacuum off-cell unloaing

滑动夹心前端-释放真空-取下电芯

station two station

side cutting knife

side cutting force 100kg

tab cutting knife

tab cutting force 100kg

2.3 assembly line process(10/15)流水线工艺

cell loading-sliding jig backward-vacuum pad down-open-needle down-e/l filling(e/l-needle up-needle up-vacuum pad up-sliding jig forward-cell unloading

station two station

e/l supply 3kuter sub-tank on equipment

metering pump hi -bar pump,hbd-2bc-17

accuracy; under 3.0;±0.1g

ocer 3.0; ±3.5g

2.3 assembly line process(11/15)流水线工艺

cell loading-sliding jig backward-jig backward-jig up-vacuum(vacuum chamber)-

放上电芯-滑动夹心后端-夹心向后-再向上-抽真空-

sealing block forward-sealing

热封前端- 密封

--sealing block backward-jig down-silding jig forward-cell loading-formation

热封后端- 夹心翻转向下-滑动夹心前端-取下电芯-成型

station two station

vacuum source 740mmhg max.vacuum pump

sealing control pressing time preset tiomer

pressing force, precision regulator

temperature, thermocouple热电偶

time:min.3~max4sec

press force:250kg

temperatrure:180~250℃

2.3 assembly line process(12/15)流水线工艺

cell loading-conveyor drive-numbering-numbering-head down-vacuum on-

放上电芯- 启动传送带- 编号码-编号码-电芯朝下-抽真空

head up-head forwward-head down-vacuum purge-head up-cell unloading

电芯朝上- 电芯朝前- 电芯朝下-真空净化- 电芯朝上-取下电芯

speed controller motor 25W

numbering ink jet printer

cell unloading magacine

2.3 assembly line process(13/15)流水线工艺

piercing-cell loading-sliding jig backward-jig up-vacuum°assing-

穿透？？- 放电芯-滑动夹心后端-夹心向上- 抽真空&脱气

sealing block forward-sealing-sealing block backward-jig down-sliding jig forward-cell loading