船舶专业英文词汇汇总
船舶英语词汇
船舶英语词汇dugout 独木舟barge 驳船kayak （爱斯基摩人的）木排outrigger 桨叉架船rowing boat 划艇（美作：rowboat）gondola （意大利的）长平底船whale mother ship 捕鲸母船hydrofoil 水翼船catamarans 双体船dredger 挖泥船boat 船brig, brigantine 双桅船canoe 小船，独木舟caravel 快帆船cargo boat 货船coaster 近海贸易货船cod-fishing boat 捕鳕鱼船whaler 捕鲸船collier 运煤船battleship 战船shallop 小型战船coastguard cutter, coastguard vessel 巡逻艇，缉私艇revenue cutter 缉私船patrol boat 巡逻艇minelayer 布雷艇minesweeper 扫雷艇torpedo boat 鱼雷艇frigate 轻护航舰gunboat 炮舰submarine 潜水艇destroyer 驱逐舰corvette 轻巡洋舰cruiser 巡洋舰aircraft carrier 航空母舰ferry, ferryboat 渡船，渡轮fishing boat 渔船freighter 货船galleon 大型帆船galley 大划桨船hovercraft 气垫船icebreaker 破冰船launch 艇lifeboat 救生艇lighter 驳船liner, ocean liner 远洋班轮merchant ship, merchantman 商船motorboat 摩托艇outboard 尾部装有马达的小艇paddle steamer, paddle boat 明轮船passenger boat 客船piragua, pirogue 独木舟raft 木筏rowing boat 划艇sailing boat, sailing ship 帆船schooner 纵帆船ship 船skiff 小艇sloop 单桅船steamer, steamship 汽轮tanker 油轮trawler 拖网渔船tug, tugboat 拖轮vessel 船yacht 游艇yawl 船载小艇构架结构 Framed structure清洁压载舱Clean ballast tank纵桁结构 Girder structure冷凝水柜Condensate catch tank人孔 manhole干舱 Dry tank饮用水舱 Drinking water tank密封圈 Sealing ring污水舱 Bilge tank铰链 Hinge应急淡水柜Emergency fresh water tank 把手 Handle首舱 Fore tank平衡块 Balance block首尖舱 Fore peak tank斜边舱Hopper side tankwelding焊接液舱 Liquid tank坡口 groove龙骨舱 Keel tank单面坡口 Single groove右舷舱 Starboard tank双面坡口 Double groove顶边水舱 Topside tankⅠ形坡口 Square groove顶边翼舱Topside wing tankV型坡口Single v groove小舱口盖Small hatch coverU型坡口Single u groove水密舱口盖Water-tight small hatch coverX形坡口Single v groove风雨密舱口盖Weather-tight small hatch coverK形坡口 Single bevel grooveY形坡口Single v groove with broad rood face填充金属 Filler metal坡口面 Groove face热影响区 Heat-affected zone(HAZ)坡口角度 Groove angle过热区 Overheated zone焊缝倾角 Weld slope焊合线 Bond line(fusion line)接头根部 Root of joint焊接区 Weld zone根部间隙 Root gap焊缝区Weld metal area钝边 Root face焊缝 weld焊接接头 Welding joint连续焊缝 Continuous weld对接接头 Butt joint断续焊缝 Intermittent weld角接接头 Corner joint纵向焊缝 Longitudinal weldT形接头 T-joint横向焊缝 Transverse weld搭接接头 Lap joint对接焊缝隙 Butt weld十字接头Cross shaped joint角焊缝 Filled weld母材 Base metal(parent metal)并列断续角焊缝Chain intermittent fillet交错断续角焊缝Staggered intermittent fillet弧焊整流器 Arc welding rectifier焊缝正面 Face of weld自动焊 Automatic welding焊缝背面 Back of weld埋弧自动焊Submerged arc welding焊缝宽度 Weld width半自动焊Semi- automatic welding焊缝长度 Weld length氩弧焊 Argon-arc welding焊缝余高 Reinforcement二氧化碳气体保护焊CO2 gas shielded arc welding 焊脚Leg(of a fillet weld)氧乙炔焊 Oxy-acetylene welding焊脚长度 Leg length气割 Gas cutting套管接头 Muff joint碳弧气刨Carbon arc air gouging手工电弧焊Manual arc welding(shielded metal arc welding)水下切割 Underwater cutting直流电弧焊Direct current arc welding等离子弧切割Plasma arc cutting交流电弧焊alternating current arc welding连续焊 Continuous welding弧焊变压器 Arc welding transformer断续焊 Intermittent welding点焊 Sport welding对接焊 Butt welding分段退焊Back step welding角焊 Fillet welding分段多层焊 Block welding搭接焊 Lap welding深溶焊 Deep penetrating welding返修焊 Re-welding跳焊 Skip welding补焊 Repair welding陶质衬垫焊Ceramic backing welding定位焊 Tack welding引弧 Striking the arc封底焊Back sealing welding焊接工艺参数 Welding condition打底焊 Backing welding焊接电流 Welding current堆焊 Surfacing(overlaying)焊接电压 Welding voltage塞焊 Plug welding焊接速度 Welding speed槽焊 Slot welding电弧电压 Arc voltage盖面焊 Consmetic welding焊丝间距 Wire spacing前倾焊 Forward welding空载电压Open circuit voltage后倾焊 Backward welding熔化速度 Melting rate41． 300吨，是船台用起重机，跨度72m。
图纸-船舶图纸常用英语词汇
图纸-船舶图纸常用英语词汇1. abrasive blasting (磨料) 喷砂法, 喷砂2. access n. 通路, 访问, 入门； vt. 存取, 接近3. acknowledge vt. 承认, 答谢, 报偿4. alignment n. 排列成行; 排列成的行列; 结盟；合作（亦作：alinement）； n. 队列, 结盟 5. annex n. 附件 vt. 并吞, 附加 6. anti slip n. 防滑 7. application n. 请求, 申请, 申请表, 应用, 运用, 施用, 敷用; 应用, 应用程序, 应用软件8. argument n. 争论, 辩论, 论据, 论点, ～(for, against) , 意见 9. assembly 装配，安装，组装组装件，总成机组，集合, 装配, 集会, 集结, 汇编【机】装配; 装配车间; 部件, 组(合) 件; 成套件; 联合装置 10. attachment strap 搭接带, 搭接板 11. available adj. 可用到的, 可利用的, 有用的, 有空的, 接受探访的 12. back strap 背垫条, 衬垫, 垫里, 垫座 13. bar 杆, 棒, 棒材, 钢筋, 型材, 型钢; 炉条, (锚链的) 横档, 闩; 【电气】汇流排; 柜台, 酒吧, 快餐柜台;阻拦, 禁止 aitch bar 工字(形) 钢, 宽缘工字材 anchor bar 撬锚棒 angle bar 角材, 角钢 back(ing) bar 【焊接】垫板, 背垫短角材batten(ing) 舱口压条bearer bar 托梁, 支承梁bearing (steel) bar 支承钢筋, 受力(钢) 筋; 承重杆, 承压条bolt bar 插销, 驻栓; 螺柱杆 bounding bar 缘周角材 brass1/ 13bar 黄铜棒 bulb bar 球缘材, 球缘钢 bulb flat bar 球扁钢bulb-angle bar 球缘角材, 球缘角钢 bulb-tee bar 丁字形球缘材, 丁字形球缘钢 bulb bus bar 【电气】汇流条, 汇流排, 母线channel bar 槽材, 槽钢 copper bar 紫铜棒 crow bar 起货钩;橇杆, 撬棒 deep (frame) bar 强肋骨 equal-angle bar 等边角材, 等边角钢 face bar 面材,缘边角材 fender bar 护舷材(小艇的) , 护舷木 filler bar 焊条 flat bar 扁材 forged stem bar 锻造首柱 frame bar 肋骨角材, 肋骨钢 guard bar 栏杆, 扶手, 扶栏 H bar 宽缘工字钢,工字钢 half-round bar 半圆钢, 半圆材I bar (窄缘) 工字钢 iron bar 扁材, 铁条, 钢条 L bar 不等边角钢, 不等边角材 mo(u) d bar 型材, 型棒 pinch bar 撬杆, 撬棍, 绞盘棒 plain bar 普通角材, 平角钢 plain bulb bar 球缘扁材, 球扁钢 rack bar 齿条, 齿杆 reinforcing bar 钢筋, 加强筋round bar 圆材, 圆钢sectional bar 型材, 型钢square bar 方材, 方钢 stop bar 止动条 T bar T形材, T形钢tooth(ed) bar 齿条, 齿杆, 齿闩 unequal angle bar不等边角钢, 不等边角材 unequal flange[unequal leg] bar 不等边角钢, 不等边角材 14. barge 驳船，大平底船 covered barge 甲板驳deck barge 甲板驳 derrick barge 浮吊，起重驳 dump barge 非自航驳 flat top barge 平甲板驳 flat bottomed barge 平底驳15. banister n. 栏杆的支柱, 楼梯的扶栏 16. batten 样条，万能曲线尺；用板条钉住 batten down 封舱 mrasureing batten标尺 17. bay 舱壁间距，强肋骨间距；集装箱货位，货柜存放器；停泊地，码头区 assembly bay 装配工段 building bay 建造工段 fitting bay 舾装工段 welding bay 焊接工段 18. beam n. 梁, 桁条, (光线的) 束, 柱, 电波, 横梁 v. 播送 19. bearing pad 乌金轴瓦, 轴承垫 20. bending shackle 锚卸扣 21. bevel n. 坡口 , 斜角 , 斜角规 , 倾斜, 斜面 vi. 成斜角 , 开坡口 , 做成斜边 vt. 使成斜角 beveling(of the edge) 开坡口, 各种形状坡口的加工 22. blade 推进器叶片(舢板) 桨叶舵板翼叶片刀口 n. 轮叶, 叶片 23. blasting n. 爆破(作业) ;鼓风; 吹净; 喷丸处理; 喷砂处理 24. boltn. 门闩, 螺钉, 闪电, 跑掉 v. 上门闩, 囫囵吞下, 逃跑 25. boss(铸锻件表面) 凸起部毂，轴毂，轮毂，轴套。
有关船舶的英文专业术语
“Maritime Terminology: Essential Vocabulary for Ships”1.Bow: The front part of the ship.2.Stern: The back part of the ship.3.Port: The left side of the ship when facing forward.4.Starboard: The right side of the ship when facing forward.5.Hull: The main body of the ship, excluding superstructure and machinery.6.Deck: The horizontal surface of a ship where people walk or work.7.Bridge: The navigational control center of the ship, usually located at the front.8.Bulkhead: A partition wall within the hull of the ship.9.Keel: The central structural member of the ship’s hull, running along the bottom.10.Rudder: A movable device used to steer the ship.11.Propeller: A rotating device that propels the ship through the water.12.Mast: A vertical structure on the ship that supports sails or antennas.13.Bilge: The lowest compartment on a ship’s hull, often prone to collecting water and otherliquids.14.Ballast: Weight added to a ship to improve stability or adjust draft.15.Cargo Hold: A space within the ship’s hull for storing cargo.16.Anchor: A heavy object deployed to keep the ship stationary.17.Windlass: A machine used for raising and lowering the anchor.18.Lifeboat: A small boat carried by a ship for use in emergencies.19.Buoy: A floating object used for navigation or marking hazards.20.Chart: A map used for navigation, showing water depths, landmarks, and other relevantinformation.These are just a few examples of the many specialized terms used in the maritime industry. Understanding these terms is essential for effective communication and safe operation aboard ships.。
船舶航海英语词汇
..船舶航海英语词汇 Ranks of ship ’s crew(船员职务) crew 船员 captain （master ） 船长 chief officer 大副 or chief mate （first mate ） second chief 二副 or second mate third officer 三副 or third mate assistant officer 驾助 radio officer （radio 报务员operator, wireless operator ） purser (chief purser) 管事,事物长 clerk 事务员 boatswain or bosun 水手长 cassab 副水手长 quartermaster 舵工 coxswain 舵工,艇长 able seaman 全能水手,一水 a.b.(able bodied seaman)全能水手 e. D.h. , d.h.u. 全能水手 o.s.(ordinary seaman)普通水手,二水 seaman, mariner 普通水手,海员 deck boy 甲板员 engineer 轮机员 chief engineer 轮机长,大车,老轨 second engineer 大管轮,二车,二轨 third engineer 二管轮,三车,三轨 fourth engineer 三管轮,四车,四轨 assistant engineer 轮助 mechanic 机工 fireman 生火 cleaner or wiper 清洁工 chief steward 大管事 (or catering officer) second steward 二管事 chief cook 大厨 second cook 二厨 supernumerary 额外人员 ship ’scomplement 船上的定员 deck serang 水手长 deck tindal 副水手长 seacunny 舵工 Names of marine organizations and their( 船务机关名称及工作人员) harbour administration bureau (or harbour bureau)港务局 the joint inspection party-inward and outward 进口联合检查组 harbour supervision office 港务监督 the customs 海关 frontier inspection station 边防检查站 quarantine office (s0ervice) 卫生检疫所 animal and plant quarantine service 动植物检疫所 china commodity inspection and testing bureau(ccitb) 中国商品检验局 china marine bunker supply corporation 中国船舶燃料供应公司 china national chartering corporation(zhongzu) 租船公司 china ocean shipping agency 中国外轮代理公司 china ocean shipping company (cosco) 中国远洋运输公司 china ocean shipping company chartering department(coschard) 中国远洋轮船公司租船部 (“中远租”) chian ocean shipping tally company 中国外轮理货公司 china ocean shipping supply corporation(supco.)中国外轮供应公司 the ~ office of the register of shipping of the people ’s republic of china 中华人民共和国船舶检验局~办事处 joint inspection party 联检小组 customs officer 海关官员 harbour officer 港务监督员 frontier defence officer (inspector ,guard) 边防检查组 Quarantine officer(dotor) 卫生检疫员 customs boarding office 登轮官员 customs searching party 海关检查组 docker 码头工人(广义) longshoreman 码头工人(在岸上装卸) stevedore 码头工人(在船上装卸) foreman 装卸队长 pilot 引水员 cargo surveyor 商品检验员 marine or ship surveyor 验船师 chief tallyman 理货员 waterman 加水工人 agent 代理 Marine loading and discharging gear and harbour facilities （海运装卸机械工具和港口设施） barge 驳船 beacon 航标灯 belt conveyor 皮带运输机 board palnk 木版 bridge crane 桥吊，装卸桥 bunkering tanker 供燃料船 buoy 浮筒，浮标 can hook ，barrel sling 吊桶钩 canvas 帆布 canvas sling 吊货帆布袋 cargo tray 吊货盘 cargo runner 吊货钢丝绳 chafing plate 防擦板 chafing mat 防擦席 chain sling 链条吊索 crane 吊车 cold storage 冷藏仓库 conveyor belt 传送带 crowbar 撬杠 customs launch 海关关艇 dolphin 系缆桩 dunnage 垫仓物料 electric crane 电吊 elevator 升降机 ferry boat 轮渡船 fire boat 消防船 floating crane 浮吊 footboard 踏板 fork - lift 铲车，叉车 funnel 漏斗 gangboard 跳板 gantry crane 龙门吊 garbage(sludge,sewage) boat 垃圾船 grab 抓斗 grain elevator 吸粮机 hammer 铁锤 handcart 手推车 harbour light 港口灯标 iron nail 铁钉 landing pier 登岸码头 lifting maget 西铁吊具 lighter 驳船 light house 灯塔 light ship 灯船 manila rope 白棕绳 mat 席子 mobile crane 流动吊车 mooring anchorage 系泊锚地 mooring buoy 系泊浮筒 motor launch 小汽艇 nylon rope 尼龙绳 oil hose 输油软管 open yard 露天货场 personnelboat 交通艇 pilot boat 引水船 plate hook 钢板吊钩 pontoon 浮码头 pontoon bridge 浮桥 quarantine anchorage 检疫锚地 quarantine vessel 检疫船 refrigerator car 冷藏车 rope sling 绳吊索 saw 锯 semi-portal crane 半门吊 shifting board 防动板 signal tower 信号台 steam launch 小汽艇 steel wire 钢丝绳 tower crane 塔吊 tractor 牵引车 traffic boat 交通艇 tug boat(motor tug) 拖轮 warehouse 仓库 water boat 供水船 watr lever indicator 水深标尺 wire cargo net 钢丝网络 wire sling 钢丝吊索 various kind of vessels （各种船舶） air cushion craft 气垫船 bage-carrier 载驳货船 bulb-bowed ship 球鼻首船 bulk-carrier 散货船 cargo liner 定期货船 collier 散货船 crew boat （船员）联络船 diesel boat 柴油机船 dry cargo ship 干货船 dumb lighter 驳船（没有机器的） freighter 货船 oil barge 油驳 ore carrier （ore ship ） 矿砂船..reefer （refrigerator ship ） 冷冻船 salvage vessel 救助船 grain carrier 运量船 ice-breaker 破冰船 light ship 未载货的货船 lumber carrier （timber carrier ） 运木船 meat ship 肉类船 moto ship 内燃机船 ocean-going vessel 远洋船 sister ship 姐妹船 steam ship 蒸汽机船 stor carrier 补给船 tanker （oil tanker ） 油驳 trawler 拖网渔船 Major marine papers and certificates （主要船务单据及证书） （1）papers 单据 application for bunkers 加(燃油)申请书 application for tallyman 理货申请书 bill of lading 提单 booking note 订舱单 boat note 订载单 cargo receipt 交货收据 cargo tally sheet 理货记数单 copy 副本 damaged cargo report 货物残损报告书 declaration 申报单 delivery order 交货单 dock receipt 码头收据 gang record 工班报单 hatch(cargo)list 分舱单 inward manifest 进口舱单 license 许可证 mate ’s receipt 收货单 notice of arrival 到货通知书 motice of claim 索赔通知 notice of readiness 准备就绪通知书 on-spot record 现场记录 original 正本 outward manifest 出口舱单 parcel receipt 小包收据 sailing orders 开航通知 shipper ’s export declaration 货物出口申请书 shipping list 装货通知书 shipping permit 准运单 short/overlanded cargo list 货物溢短单 short/overlanded cargo report 货物溢短报告单 tally daily report 理货日报告 tally sheet 理货单 tally shift report 理货工班报告 2 )certificates ( 证书,证件) certificate of freeboard 干舷证书 certificate of health 无疫证书 certificate of origin 产地证书 ceitificate of port registry 船籍港证书 certicficate of survey 船舶检验证 classification certificate 船级证书 deratting certificate 除鼠证书 deratting exemption certificate 免予除鼠证书 inspection certificate 验讫单 international loading certificate 国际载重线证书 maritime declaration of health 航海健康申明书 navigation certificate seaworthiness certificate 适行证书 outward clearance certificate 出国证书 panama canal tonnage certificate 巴拿马运河吨位证书 passport 护照 safety radio telegraphy certificate 无线电报安全证书 ship ’s safety certificate 船舶安全证书 sues canal special tonnage certificate 苏伊士运河专用吨位证书 tonnage certificate 吨位证书 tonnage dues certificate 吨税证书 wireless inspection certificate 无线电安全证书 The structure of a ship(船舶结构) accomodation 房间 accomodation ladder 舷梯 aerial(antenna) 天线 aft part(after part) 船尾部 after-peak 后尖舱 air siren 汽笛 aldis lamp 闪光信号灯 alleyway 走道 anchor 锚 anchor chain 锚链 auxiliary machinery 辅机 bilge 船底沟 binnacle 罗盘支架 bitts(bollards) 系缆柱 block 滑轮 boom 吊杆 bow 船头 port bow 左舷船头 starboard bow 右舷船头 break 夹板台阶 bridge 船桥,驾驶台 brow (从船上到岸上的)舷梯 bulwarks 舷墙 bunker 燃料舱 cabin 船舱 pilot ’s cabin 引水员房间 cable 锚链 capstan 绞盘 cargo hold 货舱 catwalk 狭窄的舷梯 awning 帆布蓬 baggage room 行李房 barometer 气压表 basic line 吨位标志线 balk(blulk) , beam 船梁 hatch beam 舱盖横梁 port beam 左舷 starboard beam 右舷 chain locker 锚链舱 chronometer 经纬仪 coamings 舱口栏板 compass 罗盘course recorder 航向记录仪crane 起重机 davit 挂艇架 deck 甲板boat deck 救生艇甲板 lower deck 下甲板 lower tween deck 二层柜 main deck 正甲板 poop deck 船尾上面的甲板promenade deck 保护甲板之上甲板 shelter deck 遮蔽甲板 tonnage deck 量吨甲板 tween(between)deck 二层柜 upper deck 上甲板 upper tween deck 三层柜 deck house 甲板室 derrick 吊杆diesel engine 柴油机double bottom 双层底 draught marks(draft marks) 吃水标志 dynamo(generat 发电机 echo sounder 测深仪 engine roon 机舱 engin roon department 机舱部 escape trunk 救生道 fan room 打风间falg-staff 旗杆 forecastle 船首楼forecastle head 船头甲板 foremast 头柜 forepart 船头部 forepeak 前尖舱freeboard deckling 干舷甲板线 gangway 舷梯 glass (口语)气压表guy 稳索 gyro compass(gyro) 电罗经 halliard ,halyard 旗帜之升降索 hatch 舱口 hatch bord 舱盖板hatch coaming 舱口栏板 hatch cover 舱口盖 hawse hole 锚链孔 helm 舵轮;舵柄 hawser 船缆;锚链hull 舱壳jack ladder(jacob ’s ladder)软梯,绳梯 jackstaff 船头小旗杆 jigger mast 尾 jumbo(derrick 重吊(杆) keel 龙骨 life belt 救生带 life bort 救生艇 life buoy 救生圈 life jacket 救生衣 life raft 救生筏life-saving apparatus 救生设备 load ling 载重线,装载水线 mainmast man-rope 绳索mizzen mast monkey island 瞭望台 pilot ladder 领港梯子..piston 活塞 plimsol ’s mark 载重线标志 poop 船尾楼 port 港口,舱口,左舷 port -hole 舷舱,舱口 propeller 螺旋桨 pulley 滑轮 pump 水泵 purchase 绳索,滑轮 quarter 船舷的后部 port quarter 左舷后部 starboard quar 右舷后部 radar 雷达 radio 无线电 radio direction finder 无线电测向器 radio room 无线电室 radio transmitter 无线电发射机 rast 救生筏 rail,railings 扶手,栏杆 rat-guard 缆绳上的防鼠隔 ratlines 绳梯横索 refrigerated hol 冷藏舱 rig 帆索 rudder 舵 screw 螺丝钉 scupper 排水管 scupper board 挡水板 scanner 雷达扫描设备 sextant 六分仪 shaft tunnel 地轴弄 shackle 钩环 shifting board 防动板,防舱板 signal rocke 信号火箭 siren 汽笛 sling 吊索 starboard 右舷 steam engine 蒸汽引擎 steering gear 舵机 stem 船头 stern 船尾 storeroom 贮藏室 tackle 滑车,吊具 tank 液体舱 ballast tank 压载水舱 cofferdam tank 隔离沧 deep tank 深舱，深水柜 1 船舶专业英语词汇（初级） 1．基本，简单的词汇： AM 上午 PM 下午 Notification of inspection 检查验收通知单 Application 申请，申请单 Inspection 检验，报验 Technical discussion 技术讨论 On board 在船上 In the workshop 在车间 On the slipway 在船台上 At pier(wharf) 在码头 Fair 尚好的 The performance is merely fair 性能尚好 Terrible 极坏的，很糟的 So so 马马虎虎 So far ,so good 到目前，一切顺利 Worse 更糟的 worst 最差、最糟 Improvement 改进 Leave no room for improvement 完美，无缺点 Accept 接收 Accept subject to 有条件的接收，有待于……做好之后才接收 Reject 拒收 Comments 意见 defect lish 消除意见清单 Item 项目 memorandum 备忘录 manual n 、手册、说明书；a.手控的，手工的 drawings 图纸 working drawings 施工图 finished drawings 完工图 approved drawings 认可图 drawings for approval 送审认可图 supporting technical doucuments 基础技术文件 sketch 草图 draw a sketch 画草图 up to the standard 达到标准 substandard 低于标准的 crane 吊车 building berth 船台 slipway 船台、下水滑道 dry dock 干无坞 pier 突码头、突堤 wharf 码头 along side (船)靠码头 foreman 工长，领班 coordinator 调度员 inspector 检查员 supervisor 管理人、监督人，监造人 surveyor 验船师 2、船体总体，及各类型船舶 Hull 船体 Forecastle 艏楼 Stern 船尾 Poop 艉楼 Superstructure 上层建筑 Foremast 前桅杆 After mast 后桅杆 Radar mast 雷达桅杆 Main deck 主甲板 Upper deck 上甲板 Poop deck 艉楼甲板 Accommodation deck 生活甲板 Compass deck 罗经甲板 Funnel 烟囱 Bridge 桥楼，驾驶台 Bridge wing 驾驶室翼桥 Wheel house 驾驶室 Engine room 机舱 Engine control room 机舱集控室 Catwalk 天桥、步桥 Flying bridge （露天）航行驾驶室 Rescue boat 救助艇 Life boat 救生艇M/Vmerchant vessels 商船Naval Auxilary vessel 军用船 Naval Ship/war shipd 军船 Ice-breaker 破冰船Container vessel 集装箱船 Oil tanker 油轮Products tanks 成品油轮Carrier 运输船、航空母舰、托架 Chemical carrier 化学品运输船 Liquefied gas carrier 液化气体船 Liquefied natural gas carrier 液化天然气运输船Aircraft carrier/aeroplane carrier 航空母舰School ship/training ship 训练船Geophysical survey ship 地球物理勘探船Cruiser 巡洋舰、大型快船、游艇 Canoe 独木船，皮舟Junk 平底中国帆船、舳板 Gondola （意大利威尼斯的 ）一种狭长的平底船Yacht 快艇、游艇 Fast boat 快艇 Patrol boat 巡逻艇Anti-smuggling boat 缉私艇 Torpedo boat 公安艇 Ferry 渡船Catamaran 双体船 Jet foil 喷水水翼艇Wing assrsted vessel 地效船 3、各专业基本词汇 1）船体：Draft forward 前吃水 Draft middle 中吃水 Draft after 后吃水 Plimsoll mark/line Waterline 吃水线Waterlines （型）水线 Port 左舷 Starboard 右舷Sagging 中垂、下垂、下挂（流） Hogging 中拱、上拱 Derformation 变形Fairing 光顺、火工校正 Hot work 热工、明火作业 section 分段、部分、剖面 Block 分段Keel （船舶）龙骨 Bilge keel 舭龙骨Power tool 带动力工具（风动或电动） Welder 电焊工Welding machine 电焊机A.C welding 交流（电弧）焊 D.C welding 直流（电弧）焊 Grinding 打磨 Welding 电焊Spatters 飞溅（电焊） Under out 咬口 Sharp edge 快口2 船舶专业英语词汇（初级） Deflection 挠曲，变形 Slags 渣..Welding slags 电焊渣Automatic welding 自动焊 Manual welding 手工焊 Arc welding 电弧焊Gas shielded welding 气体保护焊 Inter gas arc welding 惰性气体保护电弧焊Welding seam 焊缝Bending machine 弯曲机Three-roll bending machine 三芯弯板机 Torsional box 抗扭箱 V oid space 空舱 Cofferdam 隔离舱 Bulwark 舷墙，防浪板 Wall 墙壁 Floor 地板Controllable pitch 可调桨 Elastic coupling 弹性联轴节 Bellow 波纹管 Joint 接头 Gaskets 垫片Fitting bolts 拂螺拴 Chock 制动块、导缆器 Chock fast 环氧垫块 Foundation 底座、基座 Mounting 装置、座、架Mount （常指火炮等武器的）座，架 Vent pipe 透气管 Sounding pipe 探测管Vapour return line 油气回路管 Stripping line 扫舱管Safety equipment 安全设备 Life-saving equipment 救生设备 Cargo hold 货舱 Cargo oil tank 货油舱 Cabin 船舱、舱室 Room 房间Store room 储藏室 Cold room 冷库 Fish room 鱼库 Meat room 肉库 Provision room 粮库 Foam room 泡沫库 CO2 room 二氧化碳室 Pump room 泵室Battery room 蓄电池室 Radio room 报务室 Galley 厨房Ventilation system 通风系统Fresh water piping system 淡水系统 Sea water piping system 海水管系 Water jacket 水套Insulation materials 绝缘材料Lagging 绝缘材料、外套（锅炉、管子等） 3）电器 Current 电流 V oltage 电压 Frequency 频率 Contact 触点、触头 Ballast 镇流器Convertor 变频器、换能器 Conductor 导体Semi-conductor 半导体 Rectifier 整流器 Transformer 变压器 Thermostat 恒温器 Thermister 热敏器Edison base 螺丝灯座、爱迪生灯座 Bayonet base 卡口灯座 On-off 开关（量）Analogue 模拟，模拟设备Active analogue 有源模拟、主动模拟 Passive analogue 无源模拟、被动模拟 Dry contact 无源模拟、干接触 Buzzer 蜂鸣器 Button 按扭，电扭 Switch 开关Main switch 主开关Main switch board 主配电板 Cable 电缆 Wire 电线Three-core cable 三蕊电缆 Clamp 夹钳、夹具 Clip 接线柱、线夹Alligator clip 鳄鱼夹、弹簧夹 V oltage drop 电压降 Speed droop 速度降低 Black out 黑灯试验 Power failure 失电 Setting point 设定点 Adjust 调正（v ） Adjustment 调正（n ） Oscillator 振荡器、振动器 Oscilloprobe 示波器测试头 Oscilloscope 示波器、示波仪 Resistor 电阻、电阻器Potentiometer 电位器、电势计 Electrolysis 电解（作用） Electrolyte 电解质、电解液setting point of power surplus 负载余量设定值 重载询问test the power surplus setting point 重载询问试验 4）漆、木Surface preparation 表面处理（清理工作）Blasting equipment 喷漆（砂粒）装置 Sand blasting 喷砂除锈 Pre-blasting 预喷砂 Lingt blasting 预喷砂 Full blasting 通喷砂 Sand sweep 扫砂Sand blasting to SA2.5喷砂达到SA2.5级Steel work inspection after full blasting 通喷砂后钢结构检查Cleanliness inspection 清洁度检查 Inspection after degreasing 除去油脂后检查Removing oil stains by detergent/solvent 使用洗洁剂/容剂除去油迹 Shop primer 车间底漆Spray painting 喷漆、喷涂法 Touch-up 补漆、修正Touch-up painting 补漆、点漆 First coat 底漆、头道漆 Finish coat 面漆Surface coat 表面涂层 Under coat 内涂层 Wearing coat 磨耗层Zinc-rich coating 富锌涂层Cement wash coating （薄）水泥涂层 Stripe coating 预涂层 Floor covering 地板覆层 Alkyd resin paint 醇酸树脂漆Epoxy(resin-based)paint 环氧树脂涂料 3 船舶专业英语词汇（初级） Scuttle 舷窗 Carpet 地毯Wooden skirt 木裙板（踢脚）Aluminum skirt 稆质裙板（踢脚） Brass nose 装于楼梯踏步一的黄铜防滑镶条Stainless screw 不锈钢螺钉 Spring 弹簧Securing dev ice 固定件Locking device 闭锁装置，制动设备 Plywood 胶合板，层压板 Laminated plate 迭层板Laminate 层压制品，迭层板，层压板 High pressure washing of the hull 用高压水冲洗船壳Steel plate temperature 钢板温度 Condensation 冷凝Capillary condensation 毛细管现象 Dew point 露点 Flashing point 闪点Ignition point 燃点，着火点 Ventilation for coating 涂装通风 Dehumidifier 去湿机，干燥机 Dehumidification 去湿，去潮 Sagging 流挂，下垂 Chalking 粉化Peeling 剥落（指油漆） Pinhole 针孔 CureCuring 硬化，熟化，硫化 Drying film thickness(DFT)干膜（漆膜）厚度Curing temperature 硬化、固化温度 Power tools 有动力的工具（包括电动及风动）Pheomatic tools 风动工具 Burnt area 烧坏的区域 Oil stains 油迹 Scratches 划痕Damaged places 遭损坏的部位 Chicken wire 钢丝网 Tiles 瓷砖，瓦Mosaic-tile 彩色瓷砖，镶嵌瓷砖，马赛克瓷砖Glue 胶，粘结剂Silica 硅石，二氧化碳 Silicagel 硅胶Decoration 装饰，装修Interior decoration 内部装饰，内装 Deck head 天花板..Ceiling 天花板Paneling 板墙，镶板 Wall 墙壁Desk 书桌，桌台 Drawer 抽屉Catch hook 固定钩子Observation window 观察窗 Inspection window 检查孔窗 Clear view window 旋转观察窗 Curtain 窗帘Latch 止动销，插销 Valance 窗帘箱 Hanging 窗帘Eyebrow 舷窗眉板 Pre-alarm 预报警 Trip 脱扣，跳闸Preferential trip 优先脱扣 Transducer 换能器synchronize （便）同步 synchronize motor 同步电机 synchronous motor 异步电机 step motor 步进电机 diode 二极管 triode 三极管 audion 三极管 single phase 单相 three phase 三相 phase-in 逐步引进 phase-shafting 相移retarding phase 滞后相位 reversed phase 倒相，相反 relay 继电器 timer 定时器trimmer 微调电容器，调正片 delay 延时carrier 载波，载波电流transponder 发射器，应答器，询问机 echo-sound 回声测深仪radio navigation equipment 无线电导航设备log 计程仪auto-pilot 自动驾驶仪 gyro-compass 电罗经barrier 屏障，障碍，栅栏 zenner barrier 齐纳屏（使电只能单向流的半导体）radio beacon 无线电信标 pluse 脉冲blanking plus 消隐脉冲 induction 感应，感应现象 oscillation 振荡 Leak(v)渗，漏 Leakage(n) 渗，漏Overhaul 大修，彻底检修 Hammer 榔头Spanner 扳手，扳头Ring spanner 环形扳手，梅花扳手 Allen key 内六角扳手， Box spanner 套筒扳手 Torque spanner 扭力扳手Double-ended spanner 双头扳手 Monkey spanner 活络扳手，活络管扳手 Shifting spanner 活络扳手Pipe spanner 管子扳手 Reamer 铰刀Reaming （用）铰（刀扩）孔 Countersink reamer 锥形孔铰刀 Wrench 扳手，扳头 Shisel 凿子Calipers 卡钳，两脚规 Inside calipers 内卡钳 Bore 内孔Boroscopic inspection 内孔表面检查 Boroscope 内孔表面检查仪 Plug 塞（子），（内燃机）火花塞 Cock 施塞，龙头 Valve 阀P/V valve P/V 阀 Strainer 滤器Coarse strainer 粗滤器 Fine strainer 精滤器 Oil separator 分油机 Back pressure 背压 Pressure test 压力试验 Over speed 超速 Over load 超负荷Dafety device 安全装置 Fly wheel 飞轮Floating floor 浮式地板Deckhead 天花板（指由甲板形成的） Ladder 梯子Vertical ladder 直梯 Inclined ladder 斜梯Accommodation ladder 舷梯 Pilot ladder 引水员；软梯 Centering 对中心Alignment 对准，对准中心 Inspection 报验 Installation 安装Final inspection of M/E insallation 主机最终安装报验Inspection of the centering of the stern tabe before fine boring 精镗前艉轴管中心校准Alignment check/inspection 拉中心/校正报验Completeness inspection of the thermal oil circulating piping system 热油循环管系完整性报验Cleanliness inspection after flushing F.O piping system 燃油管串油后清洁检查 Function test of steering gear 舵机效甩试验Hose test of water tight doors 水密门冲水试验Noise lever measurement 噪声测量 Vibration level measurement 振动测量 Main engine (M/E)主机 Generator 发电机Emergency generator 应急发电机 Shaft generator 轴带发电机 Fresh water generator 制淡装置 Steering gear 舵机General service pump 总用泵 Pire pump 消防泵Hydraulic motor 液压马达Hydraulic nuts 液压螺帽 Rudder 舵Rudder bl ade 舵叶Propeller 车叶，螺旋桨Fixed pitch propeller 固定螺距的螺旋桨 Lofting 型线图放样Lay off （船及部件）放样，下料 Plate-cutting 钢板下料，开工Numerically-controlled cutting machine 数控切割机Cutting machine 切割机Under water plasma cutting machine 水下等离子切割机Surface preparation 表面处理 Fabrication （焊）开坡口，边缘加工（如刨边）Upside down construction method 分段装配Assembly 反身建法 Erection 装配，大合拢 Jig 装配架，胎架 Bow jip 船首部胎架Girder 纵向构件，桁（材） Beam 梁，横梁 Sections 型材Profile 型钢（条） Bar 杆，棒,棒材 Plate 板材 Angle bar 角钢I beam （窄缘）工字梁 H beam （宽缘）工字梁 Stiffener 扶强材Bracket 托架，支架，肘板 Support 支架Frame 肋骨，框架 Douler 复板Coaming （舱口）围板，缘材 Sinp 剪切 Cut 切割 Anchor 锚Anchor widdlass 锚机 Anchorage 锚位，锚地 Chain 链Chain block 链条滑车，神仙滑车 Platform 平台Crossover 跨越（梯桥），立交 Life raft 救身筏 Life buoy 救生圈Forward winch 前绞缆机 After winch 后绞缆机 Windlass 锚机 Bitt 带缆桩，系桩Fairlead 导缆钳，导缆孔 Hand rail 扶手，栏杆 Beam 横梁Frame 肋骨，框架 Scantling 构件尺寸 Cargo oil tank 货油舱 Scantling draft 结构吃水 Forepeak tank 首尖舱 After peak tank 尾尖舱Water ballast tanks(W.B.T)压载水舱 Fuel oil tank(F.O.T)燃油舱..Lubricating oil tank(L.OT)滑油舱 Diesel oil tank(D.O.T)柴油舱 Double botton 双层底Double skin 双层外板，双层蒙皮 Bow thruster 艏侧推 Propeller 车叶Fixed pitch propeller 定螺距螺旋桨 Controllable pitch propeller(CPP)可调螺距螺旋桨 Shaft 轴Tail shart 尾轴Shaft generator 轴带发电机 Watertight doors 水密门 Bulwark 舷墙 Bulkhead 舱壁Tank top 内底，液舱顶 Hatch cover 舱口盖 Manhole 人孔Fin stablizer 减摇鳍Antifouling system 防海生物的，防污染系统 Ship 船Vessel 船，舰Fabrication 制造，分段装配（precfabrication 预制，预加工） Assemble 装配，组装Erection 大合拢，船台装配 Staging 脚手架Block stage 分段阶段Mile stone （里程碑，大节点） Plate-cutting 下料，开工Keel-laying 上船台，龙骨铺设 Lauching 下水mooring trial 码头试验，系泊试验 sea trial(sea)试航delivery of the ship 交船defect list by the owner/society 船东提出的消除意见清单/船级社提出的消除意见清单design stage 设计阶段submit drawings to owner,classification society(LR 、DNV 、BV 、ABS ，etc)for approval 向船东，船级社（劳氏，挪威，法国，美国等）提交认可图纸 hull workshop 船体车间machining workshop 金工车间machinery engineering workshop 轮机车间electrical workshop 电气车间 business dept.经营处 perchasing dept.供应处 Q.C.Dept.检验处 Design dept.设计室 Painting and carpenter ’s workshop 漆木车间Project manager 项目经理 Director 指导者，厂长，董事 Managing director 执行董事，常务董事，总经理Head 首长，团长，主任Manager 经理，管理人，干事 Leader 领导者 Meeting 会议Negotiation 谈判 Agreement 协议 Shipyard 船厂 船舶专业英语词汇船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用 accommodation 居住（舱室） accommodation ladder 舷梯 adjust valve 调节阀adjustable-pitch 可调螺距式 admiralty 海军部advance coefficient 进速系数 aerostatic 空气静力学的 aft peak bulkhead 艉尖舱壁 aft peak tank 艉尖舱 aileron 副鳍air cushion vehicle 气垫船 air diffuser 空气扩散器 air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵 alignment chock 组装校准用垫楔 aluminum alloy structure 铝合金结构 American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的 anchor arm 锚臂 anchor chain 锚链 anchor crown 锚冠 anchor fluke 锚爪 anchor mouth 锚唇 anchor recess 锚穴 anchor shackle 锚卸扣 anchor stock 锚杆 angle bar 角钢angle of attack 攻角 angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷 anti-pitching fins 减纵摇鳍 antiroll fins 减摇鳍anti-rolling tank 减摇水舱 appendage 附体 artisan 技工assembly line 装配流水线 at-sea replenishment 海上补给 augment of resistance 阻力增额 auxiliary systems 辅机系统 auxiliary tank 调节水舱 axial advance 轴向进速 backing structure 垫衬结构 back-up member 焊接垫板 balance weight 平衡锤ball bearing 滚珠轴承 ball valve 球阀ballast tank 压载水舱 bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨 barge 驳船 baseline 基线basic design 基本设计 batten 压条，板条 beam 船宽，梁beam bracket 横梁肘板 beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线 Benoulli ’s law 伯努利定律 berth term 停泊期 bevel 折角 bidder 投标人 bilge 舭，舱底bilge bracket 舭肘板 bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩 blade root 叶跟blade section 叶元剖面 blast 喷丸block coefficient 方形系数 blue peter 出航旗boarding deck 登艇甲板 boat davit 吊艇架 boat fall 吊艇索 boat guy 稳艇索 bobstay 首斜尾拉索 body plan 横剖面图 bolt 螺栓，上螺栓固定 Bonjean curve 邦戎曲线 boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁 bottom side tank 底边舱 bottom transverse 底列板 boundary layer 边界层 bow line 前体纵剖线 bow wave 艏波 bowsprit 艏斜桅bow-thruster 艏侧推器 box girder 箱桁bracket floor 框架肋板 brake 制动装置 brake band 制动带brake crank arm 制动曲柄 brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸 brake hydraulic pipe 刹车液压管 breadth extreme 最大宽，计算宽度 breadth moulded 型宽 breakbulk 件杂货 breasthook 艏肘板 bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会..buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材 bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首 bulk carrier 散货船bulk oil carrier 散装油轮 bulkhead 舱壁 bulwark 舷墙bulwark plate 舷墙板 bulwark stay 舷墙支撑 buoy tender 航标船 buoyant 浮力的 buoyant box 浮箱Bureau Veritas 法国船级社 butt weld 对缝焊接butterfly screw cap 蝶形螺帽 buttock 后体纵剖线by convention 按照惯例，按约定 大秦cable ship 布缆船 cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程 camber 梁拱cant beam 斜横梁 cant frame 斜肋骨cantilever beam 悬臂梁 capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定 capsize 倾覆capsizing moment 倾覆力臂 captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积 cargo handling 货物装卸 carriage 拖车，拖架cast steel stem post 铸钢艏柱 catamaran 高速双体船 catamaran 双体的 cavitation 空泡cavitation number 空泡数 cavitation tunnel 空泡水筒 center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心 chain cable stopper 制链器 chart 海图charterer 租船人chief engineer 轮机长 chine 舭，舷，脊 chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论 classification society 船级社 cleat 系缆扣clipper bow 飞剪型船首 clutch 离合器coastal cargo 沿海客货轮 cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船 commuter 交通船 compartment 舱室 compass 罗经concept design 概念设计 connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨 constraint condition 约束条件 container 集装箱containerized 集装箱化 contract design 合同设计contra-rotating propellers 对转桨 controllable-pitch 可控螺距式 corrosion 锈蚀，腐蚀 couple 力矩，力偶 crane 克令吊，起重机 crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱 criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积 crow ’s nest 桅杆瞭望台 cruiser stern 巡洋舰尾 crussing range 航程cup and ball joint 球窝关节 curvature 曲率curves of form 各船形曲线 cushion of air 气垫damage stability 破损稳性 damper 缓冲器 damping 阻尼 davit arm 吊臂deadweight 总载重量 de-ballast 卸除压载deck line at side 甲板边线 deck longitudinal 甲板纵骨 deck stringer 甲板边板 deck transverse 强横梁deckhouse 舱面室，甲板室 deep v hull 深v 型船体 delivery 交船 depth 船深derrick 起重机，吊杆 design margin 设计余量design spiral 设计螺旋循环方式 destroyer 驱逐舰detachable shackle 散合式连接卸扣 detail design 详细设计diagonal stiffener 斜置加强筋 diagram 图，原理图，设计图 diesel engine 柴油机dimensionless ratio 无量纲比值 displacement 排水量displacement type vessel 排水型船 distributed load 分布载荷 division 站，划分，分隔 do work 做功 dock 泊靠double hook 山字钩double iteration procedure 双重迭代法 double roller chock 双滚轮式导览钳 double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索 draft 吃水drag 阻力，拖拽力 drainage 排水draught 吃水，草图，设计图，牵引力 dredge 挖泥船 drift 漂移，偏航 drilling rig 钻架 drillship 钻井船 drive shaft 驱动器轴driving gear box 传动齿轮箱 driving shaft system 传动轴系 dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计 e.h.p 有效马力eccentric wheel 偏心轮 echo-sounder 回声探深仪 eddy 漩涡eddy-making resistance 漩涡阻力 efficiency 供给能力，供给量 electrohydraulic 电动液压的 electroplater 电镀工 elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔 empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇 end open link 末端链环 end shackle 末端卸扣 endurance 续航力endurance 续航力，全功率工作时间 engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆 entrance 进流段erection 装配，安装 exhaust valve 排气阀expanded bracket 延伸肘板 expansion joint 伸缩接头 extrapolate 外插 fair 光顺faised floor 升高肋板 fan 鼓风机 fatigue 疲劳feasibility study 可行性研究 feathering blade 顺流变距桨叶。
船舶专业英语
船舶专业的基本词汇1．基本，简单的词汇：AM 上午 PM下午Notification of inspection 检查验收通知单Application 申请，申请单Inspection 检验，报验Technical discussion 技术讨论On board 在船上In the workshop 在车间On the slipway 在船台上At pier(wharf) 在码头Fair 尚好的The performance is merely fair 性能尚好Terrible 极坏的，很糟的So so 马马虎虎So far ,so good 到目前，一切顺利Worse更糟的worst最差、最糟Improvement 改进Leave no room for improvement 完美，无缺点Accept 接收Accept subject to 有条件的接收，有待于……做好之后才接收Reject 拒收Comments 意见 defect lish 消除意见清单Item 项目memorandum 备忘录manual n、手册、说明书；a.手控的，手工的drawings 图纸working drawings 施工图finished drawings 完工图approved drawings 认可图drawings for approval 送审认可图supporting technical doucuments 基础技术文件sketch 草图 draw a sketch画草图up to the standard 达到标准substandard 低于标准的crane 吊车building berth 船台slipway 船台、下水滑道dry dock 干无坞pier 突码头、突堤wharf 码头along side (船)靠码头foreman 工长，领班coordinator 调度员inspector 检查员supervisor 管理人、监督人，监造人surveyor 验船师2、船体总体，及各类型船舶Hull 船体Forecastle 艏楼Stern 船尾Poop 艉楼Superstructure 上层建筑Foremast 前桅杆After mast 后桅杆Radar mast 雷达桅杆Main deck 主甲板Upper deck 上甲板Poop deck 艉楼甲板Accommodation deck 生活甲板Compass deck 罗经甲板Funnel 烟囱Bridge 桥楼，驾驶台Bridge wing 驾驶室翼桥Wheel house 驾驶室Engine room 机舱Engine control room 机舱集控室Catwalk 天桥、步桥Flying bridge （露天）航行驾驶室Rescue boat 救助艇Life boat 救生艇M/Vmerchant vessels 商船Naval Auxilary vessel 军用船Naval Ship/war shipd 军船Ice-breaker 破冰船Container vessel 集装箱船Oil tanker 油轮Products tanks 成品油轮Carrier 运输船、航空母舰、托架Chemical carrier 化学品运输船Liquefied gas carrier 液化气体船Liquefied natural gas carrier 液化天然气运输船Aircraft carrier/aeroplane carrier 航空母舰School ship/training ship 训练船Geophysical survey ship 地球物理勘探船Cruiser 巡洋舰、大型快船、游艇Canoe 独木船，皮舟Junk 平底中国帆船、舳板Gondola （意大利威尼斯的）一种狭长的平底船Yacht 快艇、游艇Fast boat 快艇Patrol boat 巡逻艇Anti-smuggling boat 缉私艇Torpedo boat 公安艇Ferry 渡船Catamaran 双体船Jet foil 喷水水翼艇Wing assrsted vessel 地效船3、各专业基本词汇1）船体：Draft forward 前吃水Draft middle 中吃水Draft after 后吃水Plimsoll mark/lineWaterline 吃水线Waterlines （型）水线Port 左舷Starboard 右舷Sagging 中垂、下垂、下挂（流）Hogging 中拱、上拱Derformation 变形Fairing 光顺、火工校正Hot work热工、明火作业section 分段、部分、剖面Block 分段Keel （船舶）龙骨Bilge keel 舭龙骨Power tool 带动力工具（风动或电动）Welder 电焊工Welding machine 电焊机A.C welding 交流（电弧）焊D.C welding 直流（电弧）焊Grinding 打磨Welding 电焊Spatters 飞溅（电焊）Under out 咬口Sharp edge 快口Deflection 挠曲，变形Slags 渣Welding slags 电焊渣Automatic welding 自动焊Manual welding 手工焊Arc welding 电弧焊Gas shielded welding气体保护焊Inter gas arc welding惰性气体保护电弧焊Welding seam焊缝Bending machine 弯曲机Three-roll bending machine三芯弯板机Torsional box抗扭箱Void space空舱Cofferdam 隔离舱Bulwark舷墙，防浪板Wall墙壁Floor地板Controllable pitch 可调桨Elastic coupling 弹性联轴节Bellow 波纹管Joint接头Gaskets垫片Fitting bolts 拂螺拴Chock 制动块、导缆器Chock fast 环氧垫块Foundation 底座、基座Mounting 装置、座、架Mount （常指火炮等武器的）座，架Vent pipe 透气管Sounding pipe探测管Vapour return line油气回路管Stripping line扫舱管Safety equipment 安全设备Life-saving equipment救生设备Cargo hold 货舱Cargo oil tank货油舱Cabin 船舱、舱室Room房间Store room储藏室Cold room冷库Fish room鱼库Meat room 肉库Provision room粮库Foam room 泡沫库CO2 room二氧化碳室Pump room泵室Battery room蓄电池室Radio room 报务室Galley 厨房Ventilation system 通风系统Fresh water piping system 淡水系统Sea water piping system 海水管系Water jacket水套Insulation materials绝缘材料Lagging绝缘材料、外套（锅炉、管子等）3）电器Current电流Voltage电压Frequency频率Contact触点、触头Ballast镇流器Convertor变频器、换能器Conductor导体Semi-conductor半导体Rectifier整流器Transformer变压器Thermostat 恒温器Thermister热敏器Edison base 螺丝灯座、爱迪生灯座Bayonet base卡口灯座On-off开关（量）Analogue模拟，模拟设备Active analogue有源模拟、主动模拟Passive analogue无源模拟、被动模拟Dry contact无源模拟、干接触Buzzer蜂鸣器Button按扭，电扭Switch开关Main switch主开关Main switch board主配电板Cable 电缆Wire 电线Three-core cable三蕊电缆Clamp夹钳、夹具Clip 接线柱、线夹Alligator clip鳄鱼夹、弹簧夹Voltage drop 电压降Speed droop速度降低Black out 黑灯试验Power failure失电Setting point 设定点Adjust 调正（v）Adjustment调正（n）Oscillator振荡器、振动器Oscilloprobe示波器测试头Oscilloscope示波器、示波仪Resistor电阻、电阻器Potentiometer电位器、电势计Electrolysis电解（作用）Electrolyte电解质、电解液setting point of power surplus负载余量设定值重载询问test the power surplus setting point重载询问试验4）漆、木Surface preparation表面处理（清理工作）Blasting equipment喷漆（砂粒）装置Sand blasting 喷砂除锈Pre-blasting预喷砂Lingt blasting 预喷砂Full blasting 通喷砂Sand sweep扫砂Sand blasting to SA2.5喷砂达到SA2.5级Steel work inspection after full blasting通喷砂后钢结构检查Cleanliness inspection清洁度检查Inspection after degreasing除去油脂后检查Removing oil stains by detergent/solvent使用洗洁剂/容剂除去油迹Shop primer 车间底漆Spray painting喷漆、喷涂法Touch-up 补漆、修正Touch-up painting补漆、点漆First coat 底漆、头道漆Finish coat 面漆Surface coat 表面涂层Under coat 内涂层Wearing coat 磨耗层Zinc-rich coating富锌涂层Cement wash coating（薄）水泥涂层Stripe coating 预涂层Floor covering 地板覆层Alkyd resin paint醇酸树脂漆Epoxy(resin-based)paint环氧树脂涂料Scuttle舷窗Carpet地毯Wooden skirt木裙板（踢脚）Aluminum skirt稆质裙板（踢脚）Brass nose装于楼梯踏步一的黄铜防滑镶条Stainless screw不锈钢螺钉Spring 弹簧Securing dev ice固定件Locking device闭锁装置，制动设备Plywood胶合板，层压板Laminated plate迭层板Laminate层压制品，迭层板，层压板High pressure washing of the hull用高压水冲洗船壳Steel plate temperature 钢板温度Condensation冷凝Capillary condensation毛细管现象Dew point露点Flashing point闪点Ignition point 燃点，着火点Ventilation for coating 涂装通风Dehumidifier去湿机，干燥机Dehumidification 去湿，去潮Sagging流挂，下垂Chalking粉化Peeling剥落（指油漆）Pinhole针孔CureCuring硬化，熟化，硫化Drying film thickness(DFT)干膜（漆膜）厚度Curing temperature硬化、固化温度Power tools有动力的工具（包括电动及风动）Pheomatic tools风动工具Burnt area烧坏的区域Oil stains油迹Scratches划痕Damaged places遭损坏的部位Chicken wire钢丝网Tiles瓷砖，瓦Mosaic-tile彩色瓷砖，镶嵌瓷砖，马赛克瓷砖Glue胶，粘结剂Silica硅石，二氧化碳Silicagel硅胶Decoration装饰，装修Interior decoration内部装饰，内装Deck head 天花板Ceiling天花板Paneling板墙，镶板Wall墙壁Desk书桌，桌台Drawer 抽屉Catch hook固定钩子Observation window 观察窗Inspection window检查孔窗Clear view window旋转观察窗Curtain 窗帘Latch止动销，插销Valance窗帘箱Hanging窗帘Eyebrow舷窗眉板Pre-alarm预报警Trip脱扣，跳闸Preferential trip优先脱扣Transducer换能器synchronize（便）同步synchronize motor同步电机synchronous motor异步电机step motor步进电机diode二极管triode三极管audion三极管single phase单相three phase三相phase-in逐步引进phase-shafting相移retarding phase 滞后相位reversed phase倒相，相反relay继电器timer定时器trimmer微调电容器，调正片delay延时carrier载波，载波电流transponder发射器，应答器，询问机echo-sound回声测深仪radio navigation equipment无线电导航设备log计程仪auto-pilot自动驾驶仪gyro-compass电罗经barrier屏障，障碍，栅栏zenner barrier齐纳屏（使电只能单向流的半导体）radio beacon无线电信标pluse脉冲blanking plus 消隐脉冲induction感应，感应现象oscillation振荡Leak(v)渗，漏Leakage(n) 渗，漏Overhaul大修，彻底检修Hammer榔头Spanner扳手，扳头Ring spanner环形扳手，梅花扳手Allen key 内六角扳手，Box spanner套筒扳手Torque spanner扭力扳手Double-ended spanner双头扳手Monkey spanner活络扳手，活络管扳手Shifting spanner活络扳手Pipe spanner管子扳手Reamer铰刀Reaming （用）铰（刀扩）孔Countersink reamer锥形孔铰刀Wrench扳手，扳头Shisel凿子Calipers卡钳，两脚规Inside calipers内卡钳Bore 内孔Boroscopic inspection内孔表面检查Boroscope内孔表面检查仪Plug塞（子），（内燃机）火花塞Cock施塞，龙头Valve阀P/V valve P/V阀Strainer滤器Coarse strainer粗滤器Fine strainer精滤器Oil separator分油机Back pressure背压Pressure test压力试验Over speed 超速Over load超负荷Dafety device 安全装置Fly wheel飞轮Floating floor 浮式地板Deckhead 天花板（指由甲板形成的）Ladder 梯子Vertical ladder直梯Inclined ladder斜梯Accommodation ladder舷梯Pilot ladder引水员；软梯2)轮机Centering对中心Alignment对准，对准中心Inspection报验Installation安装Final inspection of M/E insallation主机最终安装报验Inspection of the centering of the stern tabe before fine boring 精镗前艉轴管中心校准Alignment check/inspection拉中心/校正报验Completeness inspection of the thermal oil circulating piping system 热油循环管系完整性报验Cleanliness inspection after flushing F.O piping system燃油管串油后清洁检查Function test of steering gear舵机效甩试验Hose test of water tight doors水密门冲水试验Noise lever measurement噪声测量Vibration level measurement 振动测量Main engine (M/E)主机Generator发电机Emergency generator应急发电机Shaft generator轴带发电机Fresh water generator 制淡装置Steering gear 舵机General service pump总用泵Pire pump消防泵Hydraulic motor 液压马达Hydraulic nuts液压螺帽Rudder舵Rudder bl ade舵叶Propeller车叶，螺旋桨Fixed pitch propeller固定螺距的螺旋桨Lofting型线图放样Lay off（船及部件）放样，下料Plate-cutting钢板下料，开工Numerically-controlled cutting machine数控切割机Cutting machine切割机Under water plasma cutting machine水下等离子切割机Surface preparation表面处理Fabrication（焊）开坡口，边缘加工（如刨边）Upside down construction method分段装配Assembly 反身建法Erection装配，大合拢Jig装配架，胎架Bow jip 船首部胎架Girder纵向构件，桁（材）Beam梁，横梁Sections型材Profile型钢（条）Bar 杆，棒,棒材Plate板材Angle bar角钢I beam（窄缘）工字梁H beam（宽缘）工字梁Stiffener扶强材Bracket托架，支架，肘板Support 支架Frame肋骨，框架Douler复板Coaming（舱口）围板，缘材Sinp剪切Cut切割Anchor锚Anchor widdlass 锚机Anchorage锚位，锚地Chain链Chain block链条滑车，神仙滑车Platform平台Crossover跨越（梯桥），立交Life raft 救身筏Life buoy 救生圈Forward winch 前绞缆机After winch 后绞缆机Windlass锚机Bitt带缆桩，系桩Fairlead导缆钳，导缆孔Hand rail扶手，栏杆Beam横梁Frame肋骨，框架Scantling构件尺寸Cargo oil tank货油舱Scantling draft结构吃水Forepeak tank首尖舱After peak tank尾尖舱Water ballast tanks(W.B.T)压载水舱Fuel oil tank(F.O.T)燃油舱Lubricating oil tank(L.OT)滑油舱Diesel oil tank(D.O.T)柴油舱Double botton双层底Double skin双层外板，双层蒙皮Bow thruster艏侧推Propeller车叶Fixed pitch propeller定螺距螺旋桨Controllable pitch propeller(CPP)可调螺距螺旋桨Shaft轴Tail shart尾轴Shaft generator轴带发电机Watertight doors水密门Bulwark舷墙Bulkhead舱壁Tank top内底，液舱顶Hatch cover舱口盖Manhole人孔Fin stablizer减摇鳍Antifouling system防海生物的，防污染系统Ship船Vessel船，舰Fabrication制造，分段装配（precfabrication预制，预加工）Assemble装配，组装Erection大合拢，船台装配Staging脚手架Block stage分段阶段Mile stone（里程碑，大节点）Plate-cutting下料，开工Keel-laying上船台，龙骨铺设Lauching下水mooring trial码头试验，系泊试验sea trial(sea)试航delivery of the ship交船defect list by the owner/society船东提出的消除意见清单/船级社提出的消除意见清单design stage设计阶段submit drawings to owner,classification society(LR、DNV、BV、ABS，etc)for approval向船东，船级社（劳氏，挪威，法国，美国等）提交认可图纸hull workshop船体车间machining workshop金工车间machinery engineering workshop轮机车间electrical workshop电气车间business dept.经营处perchasing dept.供应处Q.C.Dept.检验处Design dept.设计室Painting and carpenter’s workshop漆木车间Project manager项目经理Director指导者，厂长，董事Managing director执行董事，常务董事，总经理Head首长，团长，主任Manager经理，管理人，干事Leader领导者Meeting会议Negotiation谈判Agreement协议Shipyard船厂。
船舶专业英语词汇
ABS (American Bureau of Standard)美国船级社ANG (Angle Bar)角钢BFE (Builder Furnish Equipment)建造商提供设备BG (Bulk Carrier)散货船BHD (Bulkhead)舱壁BHP (Break Horsepower)制动马力BL (Base Line)基线BM (Breadth Molded)型宽BV (Bureau Veritas)法国船级社CAD (Computer Aided Design)计算机辅助设计CAM (Computer Aided Manufacturing)计算机辅助制造CB (Center of Buoyancy)浮心CCS (China Classification Society)中国船级社CF (Center of Floatation)漂心CFE (Contractor Furnish Equipment)承包商提供设备CG (Center of Gravity)重心CH (Channel)槽钢CM (Metacenter)稳心CPP (The Controllable Pitch Propeller)可调螺距桨CS (Carbon Steel)碳素钢DB (Double Bottom)双层底DK (Deck)甲板DM (Depth Molded)型深DNV (Det Norske Veritas)挪威船级社DWG (Drawing)图DWL (Design Waterline)设计水线DWT (Deadweight)载重量FAT (Factory Acceptance Test)工厂验收试验FB (Flat Bar)扁钢FEM (Finite Element Method)有限元法FPSO (Floating Production Storage Offloading) 浮（船）式生产储油卸油系统FSO (Floating Storage Offloading)浮（船）式储油卸油系统Fwd (Forward)向船艏GL (Germanischer Lloyd)德国船级社GM (Metacentric Height)初稳心高HP (Half Bulb Plate)球扁钢LBP (Length between Perpendiculars)垂线间长LCG (Longitudinal Center of Gravity)纵向重心LNG (Liquefied Natural Gas Vessel) 液化石油气船LOA (Overall Length)总长Long. (Longitudinal)纵骨LPG (Liquefied Petroleum Gas Vessel) 液化天然气船LR (Lloyd's Register)英国劳氏船级社MDK (Main Deck)主甲板MODU (Mobile Offshore Drilling Units)移动式近海钻井平台MS (Mild Steel)低碳钢MTO (Material Takeoff)材料估算NK (Nippon Kaiji Kyokai)日本海事协会OFE (Owner Furnished Equipment)船东提供设备OT (Oil Tight)油密PL (Plate)板RI (Register Italian)意大利船级社SB (Starboard)右舷Semi- (Semi-submersible Platform)半潜式钻井平台STLP (Suspended Tension Leg Platform)悬式张力腿平台TCG (Transverse Center of Gravity)横向重心TEU (Twenty-foot equivalent Unit)20英尺国际标准集装箱TLP (Tension Leg Platform)张力腿平台UCLL (Ultra Large Crude Carrier)超大型油船VCG (Vertical Center of Gravity)垂向重心VLCC (Very Large Crude Carrier)特大型油船WB (Web Bar)腹板WL (Waterline)水线WT (Water Tight)水密MECHANICAL & PIPING（轮机）：AHU (Air Handling Unit)通风装置BHP (Break Horsepower)制动马力A/C (Air Compressor)空气压缩机A/C (Air Conditioning)空调BB (Ball Bearing)滚珠轴承BRG (Bearing)轴承CAS NUT(Castle Nut)蝶型螺帽CCR (Central Control Room)中心控制室COW (Crude Oil Washing)原油洗舱DFO (Diesel Fuel Oil)柴油DPS (Dynamic Position System)动力定位系统DT (Double-Thread)双头螺纹FS (Forged Steel)锻钢FW (Fresh Water)淡水FO (Fuel Oil)燃油GRP (Glass-reinforced Plastic)玻璃钢HVAV (Heating Ventilation and Air-condition)暖通空调系统HPU (Hydraulic Power Unit)液压工作站LSA (Life Saving Apparatus)救生器具LCC (Local Control Console)机旁控制台LO (Lube Oil)滑油MDO (Marine Diesel Oil)船用柴油OS (Operation System)操作系统PLC (Programmable Logic Controller)逻辑控制单元PMS (Power Manage System)动力管理系统ELECTRICAL（电气）:AC (Alternative Current)交流电AVR (Automatic Voltage Regulation)自动电压调整计CCTV (Closed Circuit Television)闭路电视CMS (Cargo Monitoring System)货物监控系统DC (Direct Current)直流电DFT (Dry Film Thickness)干膜DG (Diesel Generator)柴油发电机DVD (Digital Video Disc) 数字化视频光盘EMSP (Emergency Shutter Panel)应急关断板ESS (Emergence Shutdown System)应急关闭系统GPS (Global Position System)全球定位系统HG (Harbor Generator)停泊发电机HT (High Temperature)高温JB (Junction Box)接线盒LED (Light Emitting Diode)发光二极管LT (Low Temperature)低温MCU (Main Control Unit)主控器箱MG (Main Generator)主发电机MUR (Manual Voltage Regulation)手动调压器NEMA (National Electrical Manufacturers Association)国际电气制造业协会PA (Public Address System)公共寻呼系统PWM (Pulse Width Modulation)脉宽调制ST (Starter)启动器SWBD (Switch Board)配电盘，配电板UPS (Uninterrupted Power Supply)不间断电源VCR (Video Cassette Recorder)录像机PAINTING（涂装）:ARD (Alkyd Resin Deck)醇酸树脂甲板漆ARF (Alkyd Resin Finish)醇酸树脂面漆ARP (Alkyd Resin Primer)醇酸树脂底漆A/C (Anti-corrosive Paint)防腐漆CAF (Compressed Asbestos Fiber)压缩石棉填料EDP (Epoxy Deck Paint)环氧甲板漆EFP (Epoxy Finish Paint)环氧面漆EPP (Epoxy Primer Paint)环氧底漆ETPF (Epoxy Tank Paint Finish)环氧舱室面漆ETPP (Epoxy Tank Paint Primer)环氧舱室底漆ETP (Epoxy Topside Paint)环氧干舷漆ERL (Erosion Resistant Lacquer)防腐漆ECP (Etching Primer) 磷化底漆EPR (Ethylene-Propylene Rubber)乙丙橡胶F/C (Finish Coating)面漆IZP (Inorganic Zinc Primer)无机锌底漆IZSP (Inorganic Zinc Shop Primer)无机锌车间底漆UTP (Polyurethane Topside Primer)聚氨脂干舷漆TE (Tar Epoxy Paint)环氧焦油漆VTP (Vinyl Tar Primer)聚乙烯焦油底漆ZRP (Zinc Rich Primer)富锌底漆WELDING and Material（焊接与材料）ASTM (American Society for Testing Materials)美国材料实验协会AWS (American Welding Society)美国焊接协会FCAW (Flux Cored Arc Welding)药芯焊丝电弧焊FRP (Fiberglass Reinforced Polyester)玻璃钢GMAW (Gas Metal Arc Welding)气体保护金属极电弧焊GRP (Glass Reinforced Polyester)玻璃钢GTAW (Gas Tungsten Arc Welding)气体保护钨极电弧焊GW (Gravity Welding)重力焊MPI (Magnetic Particle Inspection) 磁粒检验NDE (Nondestructive Evaluation)无损鉴定NDT (Nondestructive Testing)非破坏性检验PVC (Poly Vinyl Chloride)聚氯乙烯S/W (Spot Weld) 点焊SAW (Submerge Arc Welding)埋弧焊SMAW (Shielded Metal Arc Welding)手弧焊UT (Ultrasonic Test)超声波检验WPS (Welding Procedure Sheet)焊接程序表WQT (Welding Qualification Test)焊工资格检验OTHERS（其它）AE (Assistant Engineer)助理工程师ANSI (American National Standards Institute)美国国家标准局API (American Petroleum Institute)美国石油协会ASME (American Society of Mechanical Engineers)美国机械工程师协会Bbls (Barrels) 桶（美制容量单位1桶= 159升），C.E. (Chief Engineer) 总工程师CEO (Chief Executive Officer)首席执行总裁CIS (Chinese Industrial Standard)中国工业标准CNOOC (China National Offshore Oil Company)中国海洋石油总公司Co Ltd.(Company Limited)（股份）有限公司cu.ft. (Cubic Feet) 立方英尺cu.in. (Cubic Inch) 立方英寸GB (Guo Biao)国标GM (General Manage)总经理H.Q. (Headquarters) 总部HSE (Health, Safety & Environment)健康，安全和环保ID (Inner Dimension)内径IEC (International Electro technical Commission)国际电工协会IMO (Intergovernmental Marine Organization)国际海事组织ISO (International Standardization Organization)国际标准化协会ITU (International Telecommunication Union)国际电信联盟Ksi (kilopounds per square inch)千磅/平方英寸N/A (None Applicable)不适用NACE (National Association of Corrosion Engineer)全国防蚀工程师协会NFPA (National Fire Protection Association)国家防火协会OD (outer Dimension)外径QA (Quality Assurance)质量保证QC (Quality Control)质量管理（检查）ST (Short Ton)短吨SOLAS (International Convention of the Safety of Life at Sea)国际海上人命安全公约Spec. (specification)说明书，规格书sq.ft. (Square Feet) 平方英尺sq.in. (Square Inch) 平方英寸PROPER NOUN（专有名词）:Basic Design(基础设计): Preparation of specification and plans/drawings outlining the design and in sufficient detail to gain Class approval.总括性的设计规格书和图纸等，其详细程度仅足可以通过船级社认可其设计思想。
船舶专业英文词汇
船舶专业英文词汇
CAE(computer-aided manufacturing) 计算机辅助制造 CAM(computer-aided engineering) 计算机辅助工程 camber 梁拱 cant beam 斜横梁 cant frame 斜肋骨 cantilever beam 悬臂梁 capacity plan 舱容图 CAPP(computer –aided process planning) 计算机辅助施工计划制定 capsize 倾覆 capsizing moment 倾覆力臂 captain 船长 captured-air-bubble vehicle 束缚气泡减阻船 cargo cubic 货舱舱容，载货容积 cargo handling 货物装卸 carriage 拖车，拖架 cast steel stem post 铸钢艏柱 catamaran 高速双体船 catamaran 双体的 cavitation 空泡 cavitation number 空泡数 cavitation tunnel 空泡水筒 center keelson 中内龙骨 centerline bulkhead 中纵舱壁 centroid 型心，重心，质心，矩心 chain cable stopper 制链器 chart 海图 charterer 租船人 chief engineer 轮机长 chine 舭，舷，脊 chock 导览钳 CIM(computer integrated manufacturing) 计算机集成组合制造
/ShowPost.asp?ThreadID=519（第 1／31 页）2007-2-5 20:33:21
船舶英语词汇
船舶英语词汇船舶英语词汇汇总船舶专业主要培养具备现代船舶与海洋工程设计、研究、建造的基本技能和管理基础知识、计算机编程及应用能力，能在船舶与海洋结构物设计、研究、制造、检验、使用和管理等部门从事技术和管理方面工作的船舶与海洋工程学科高级工程技术人员。
下面店铺为大家推荐一些关于船舶专业的英语词汇，希望对大家的学习有所帮助。
祝纳汽阀图 Zeuner valve diagram零位线 zero line交错铆 zigzag riveting交错铆接 zigzag riveting锌铬黄(漆) zinc chromate锌板 zinc plate保护用]锌板 zinc protector[锌块 zinc slab零值中心安培计 zero center ammeterZ形推进系 Z-peller交错固结 zigzag fastening镀锌 zincing含锌漆 zincrich paint荧光探伤法 zyglo inspection method硅氟化锌 zinc fluosilicate区域?装 zone outfitting零位线 zero line零相电流 zero phase sequence current无推力节距(螺桨) zero thrust pitch锌 zinc锌池 zinc bath零弯矩跨距 zero moment span荧光渗透探伤法 zyglo penetrant method 镀锌 zinc galvanizing (or plating)区域 zone无扭矩节距(螺桨) zero torque pitchZ形材 Z bar曲折接法 zigzag connection交错间断焊接 zigzag intermittent weld 零相[序] zero phase sequence祝纳氏汽阀图 Zeuner valve diagram曲折操纵,Z形操纵 zigzag maneuvering 零升力攻角 zero-lift angle交错焊接 zigzag weld。
船舶航海英语词汇
船舶航海英语词汇中国外轮代理公司fork - lift 铲车，叉车Ranks of ship’s crew(船员职务) china ocean shipping company (cosco) funnel 漏斗crew 船员gangboard 跳板中国远洋运输公司captain（master）船长china ocean shipping company gantry crane 龙门吊chief officer 大副chartering department(coschard) garbage(sludge,sewage) boat垃圾船or chief mate（first mate）中国远洋轮船公司租船部(“中grab 抓斗second chief 二副远租”) grain elevator 吸粮机or second mate chian ocean shipping tally company hammer 铁锤third officer 三副handcart 手推车中国外轮理货公司or third mate china ocean shipping supply harbour light 港口灯标assistant officer 驾助corporation(supco.)中国外轮供应公司iron nail 铁钉radio officer （radio 报务员the ~ office of the register of shipping of landing pier 登岸码头operator, wireless operator）the people’s republic of china 中华人lifting maget 西铁吊具purser (chief purser) 管事,事物长民共和国船舶检验局~办事处lighter 驳船clerk 事务员joint inspection party 联检小组light house 灯塔boatswain or bosun 水手长customs officer 海关官员light ship 灯船cassab 副水手长harbour officer 港务监督员manila rope 白棕绳quartermaster 舵工frontier defence officer (inspector ,guard) mat 席子coxswain 舵工,艇长mobile crane 流动吊车边防检查组able seaman 全能水手,一水Quarantine officer(dotor) 卫生检疫员mooring anchorage 系泊锚地a.b.(able bodied seaman全)能水手customs boarding office 登轮官员mooring buoy 系泊浮筒e. D.h. , d.h.u. 全能水手customs searching party 海关检查组motor launch 小汽艇o.s.(ordinary seaman)普通水手,二水docker 码头工人(广义) nylon rope 尼龙绳seaman, mariner普通水手,海员longshoreman 码头工人(在岸上装卸) oil hose 输油软管deck boy 甲板员stevedore 码头工人(在船上装卸) open yard 露天货场engineer 轮机员foreman 装卸队长personnelboat 交通艇chief engineer 轮机长,大车,老轨pilot 引水员pilot boat 引水船second engineer大管轮,二车,二轨cargo surveyor 商品检验员plate hook 钢板吊钩third engineer 二管轮,三车,三轨marine or ship surveyor 验船师pontoon 浮码头fourth engineer 三管轮,四车,四轨chief tallyman 理货员pontoon bridge 浮桥assistant engineer 轮助waterman 加水工人quarantine anchorage 检疫锚地mechanic 机工agent 代理quarantine vessel检疫船fireman 生火Marine loading and discharging gear refrigerator car 冷藏车cleaner or wiper 清洁工and harbour facilities rope sling 绳吊索chief steward 大管事saw 锯（海运装卸机械工具和港口设施）(or catering officer) barge 驳船semi-portal crane 半门吊second steward 二管事beacon 航标灯shifting board 防动板chief cook 大厨belt conveyor 皮带运输机signal tower 信号台second cook 二厨board palnk 木版steam launch 小汽艇supernumerary 额外人员bridge crane 桥吊，装卸桥steel wire 钢丝绳ship’scomplement船上的定员bunkering tanker 供燃料船tower crane 塔吊deck serang 水手长buoy 浮筒，浮标tractor 牵引车deck tindal 副水手长can hook，barrel sling 吊桶钩traffic boat 交通艇seacunny 舵工canvas 帆布tug boat(motor tug) 拖轮Names of marine organizations and canvas sling 吊货帆布袋warehouse 仓库their( 船务机关名称及工作人员) cargo tray 吊货盘water boat 供水船harbour administration bureau (or cargo runner 吊货钢丝绳watr lever indicator 水深标尺harbour bureau)港务局chafing plate 防擦板wire cargo net 钢丝网络the joint inspection party-inward and chafing mat 防擦席wire sling 钢丝吊索outward 进口联合检查组chain sling 链条吊索various kind of vessels（各种船舶）harbour supervision office 港务监督crane 吊车air cushion craft 气垫船the customs 海关cold storage 冷藏仓库bage-carrier 载驳货船frontier inspection station 边防检查站conveyor belt 传送带bulb-bowed ship 球鼻首船quarantine office (s0ervice) 卫生检疫所crowbar 撬杠bulk-carrier 散货船animal and plant quarantine service 动customs launch 海关关艇cargo liner 定期货船植物检疫所dolphin 系缆桩collier 散货船china commodity inspection and testing dunnage 垫仓物料crew boat （船员）联络船bureau(ccitb) 中国商品检验局electric crane 电吊diesel boat 柴油机船china marine bunker supply corporation elevator 升降机dry cargo ship 干货船中国船舶燃料供应公司ferry boat 轮渡船dumb lighter 驳船（没有机器的）china national chartering fire boat 消防船freighter 货船corporation(zhongzu) 租船公司floating crane 浮吊oil barge 油驳china ocean shipping agency footboard 踏板ore carrier（ore ship）矿砂船reefer（refrigerator ship）冷冻船international loading certificate 国际载course recorder 航向记录仪salvage vessel 救助船crane 起重机重线证书grain carrier 运量船maritime declaration of health 航海健davit 挂艇架ice-breaker 破冰船deck 甲板康申明书light ship 未载货的货船navigation certificate seaworthiness boat deck 救生艇甲板lumber carrier（timber carrier）运木船certificate 适行证书lower deck 下甲板meat ship 肉类船outward clearance certificate 出国证书lower tween deck 二层柜moto ship 内燃机船panama canal tonnage certificate 巴拿马main deck 正甲板ocean-going vessel 远洋船poop deck 船尾上面的甲板运河吨位证书sister ship 姐妹船passport 护照promenade deck 保护甲板之上甲板steam ship 蒸汽机船safety radio telegraphy certificate 无线电shelter deck 遮蔽甲板stor carrier 补给船tonnage deck 量吨甲板报安全证书tanker（oil tanker）油驳ship’s safety certificate 船舶安tween(between)deck 二层柜trawler 拖网渔船upper deck 上甲板全证书Major marine papers and certificates（主sues canal special tonnage certificate upper tween deck 三层柜要船务单据及证书）苏伊士运河专用吨位证书deck house 甲板室（1）papers单据tonnage certificate 吨位证书derrick 吊杆application for bunkers 加(燃油)申请书tonnage dues certificate 吨税证书diesel engine 柴油机application for tallyman 理货申请书wireless inspection certificate 无线电double bottom 双层底bill of lading 提单draught marks(draft marks) 吃水标志安全证书booking note 订舱单The structure of a ship(船舶结构) dynamo(generat 发电机boat note 订载单accomodation 房间echo sounder 测深仪cargo receipt 交货收据accomodation ladder 舷梯engine roon 机舱cargo tally sheet 理货记数单aerial(antenna) 天线engin roon department 机舱部copy 副本aft part(after part) 船尾部escape trunk 救生道damaged cargo report 货物残损报告书after-peak 后尖舱fan room 打风间declaration 申报单air siren 汽笛falg-staff 旗杆delivery order 交货单aldis lamp 闪光信号灯forecastle 船首楼dock receipt 码头收据alleyway 走道forecastle head 船头甲板gang record 工班报单anchor 锚foremast 头柜hatch(cargo)list 分舱单anchor chain 锚链forepart 船头部inward manifest 进口舱单auxiliary machinery 辅机forepeak 前尖舱license 许可证bilge 船底沟freeboard deckling 干舷甲板线mate’s receipt 收货单binnacle 罗盘支架gangway 舷梯notice of arrival 到货通知书bitts(bollards) 系缆柱glass (口语)气压表motice of claim 索赔通知block 滑轮guy 稳索notice of readiness 准备就绪通知书boom 吊杆gyro compass(gyro) 电罗经on-spot record 现场记录bow 船头halliard ,halyard 旗帜之升降索original 正本port bow 左舷船头hatch 舱口outward manifest 出口舱单starboard bow 右舷船头hatch bord 舱盖板parcel receipt 小包收据break 夹板台阶hatch coaming 舱口栏板sailing orders 开航通知bridge 船桥,驾驶台hatch cover 舱口盖shipper’s export declaration 货物出口brow (从船上到岸上的)舷梯hawse hole 锚链孔申请书bulwarks 舷墙helm 舵轮;舵柄shipping list 装货通知书bunker 燃料舱hawser 船缆;锚链shipping permit 准运单cabin 船舱hull 舱壳short/overlanded cargo list 货物溢短单pilot ’s cabin 引水员房间jack ladder(jacob’s ladder)软梯,绳梯short/overlanded cargo report 货物cable 锚链jackstaff 船头小旗杆溢短报告单capstan 绞盘jigger mast 尾tally daily report 理货日报告cargo hold 货舱jumbo(derrick 重吊(杆)tally sheet 理货单catwalk 狭窄的舷梯keel 龙骨tally shift report 理货工班报告awning 帆布蓬life belt 救生带2 )certificates ( 证书,证件) baggage room 行李房life bort 救生艇certificate of freeboard 干舷证书barometer 气压表life buoy 救生圈certificate of health 无疫证书basic line 吨位标志线life jacket 救生衣certificate of origin 产地证书balk(blulk) , beam 船梁life raft 救生筏ceitificate of port registry 船籍港证书hatch beam 舱盖横梁life-saving apparatus 救生设备certicficate of survey 船舶检验证port beam 左舷load ling 载重线,装载水线classification certificate 船级证书starboard beam 右舷mainmastderatting certificate 除鼠证书chain locker 锚链舱man-rope 绳索deratting exemption certificate 免予chronometer 经纬仪mizzen mast除鼠证书coamings 舱口栏板monkey island 瞭望台inspection certificate 验讫单compass 罗盘pilot ladder 领港梯子piston 活塞So far ,so good 到目前，一切顺利M/Vmerchant vessels 商船plimsol’s mark 载重线标志Worse更糟的Naval Auxilary vessel 军用船poop 船尾楼worst 最差、最糟Naval Ship/war shipd 军船port 港口,舱口,左舷Improvement 改进Ice-breaker 破冰船port -hole 舷舱,舱口Leave no room for improvement 完美，Container vessel 集装箱船propeller 螺旋桨Oil tanker 油轮无缺点pulley 滑轮Accept 接收Products tanks 成品油轮pump 水泵Accept subject to 有条件的接收，有待Carrier 运输船、航空母舰、托架purchase 绳索,滑轮于,, 做好之后才接收Chemical carrier 化学品运输船quarter 船舷的后部Reject 拒收Liquefied gas carrier 液化气体船port quarter 左舷后部Comments 意见defect lish 消除意见Liquefied natural gas carrier 液化天然starboard quar 右舷后部清单气运输船radar 雷达Item 项目Aircraft carrier/aeroplane carrier 航空母radio 无线电memorandum 备忘录舰radio direction finder 无线电测向器manual n、手册、说明书； a.手控的，School ship/training ship 训练船radio room 无线电室Geophysical survey ship 地球物理勘探手工的radio transmitter 无线电发射机drawings 图纸船rast 救生筏working drawings 施工图Cruiser 巡洋舰、大型快船、游艇rail,railings 扶手,栏杆finished drawings 完工图Canoe 独木船，皮舟rat-guard 缆绳上的防鼠隔approved drawings 认可图Junk 平底中国帆船、舳板ratlines 绳梯横索drawings for approval 送审认可图Gondola （意大利威尼斯的）一种狭refrigerated hol 冷藏舱supporting technical doucuments 基础长的平底船rig 帆索Yacht 快艇、游艇技术文件rudder 舵sketch 草图draw a sketch 画草Fast boat 快艇screw 螺丝钉Patrol boat 巡逻艇图scupper 排水管up to the standard 达到标准Anti-smuggling boat 缉私艇scupper board 挡水板substandard 低于标准的Torpedo boat 公安艇scanner 雷达扫描设备crane 吊车Ferry 渡船sextant 六分仪building berth 船台Catamaran 双体船shaft tunnel 地轴弄slipway 船台、下水滑道Jet foil 喷水水翼艇shackle 钩环dry dock 干无坞Wing assrsted vessel 地效船shifting board 防动板,防舱板pier 突码头、突堤3、各专业基本词汇signal rocke 信号火箭wharf 码头1）船体：siren 汽笛along side (船)靠码头Draft forward 前吃水sling 吊索foreman 工长，领班Draft middle 中吃水starboard 右舷coordinator 调度员Draft after 后吃水steam engine 蒸汽引擎inspector 检查员Plimsoll mark/linesteering gear 舵机supervisor 管理人、监督人，监造人Waterline 吃水线stem 船头surveyor 验船师Waterlines （型）水线stern 船尾2、船体总体，及各类型船舶Port 左舷storeroom 贮藏室Hull 船体Starboard 右舷tackle 滑车,吊具Forecastle 艏楼Sagging 中垂、下垂、下挂（流）tank 液体舱Stern 船尾Hogging 中拱、上拱ballast tank 压载水舱Poop 艉楼Derformation 变形cofferdam tank 隔离沧Superstructure 上层建筑Fairing 光顺、火工校正deep tank 深舱，深水柜Foremast 前桅杆Hot work 热工、明火作业1 船舶专业英语词汇（初级）After mast 后桅杆section 分段、部分、剖面1．基本，简单的词汇：Radar mast 雷达桅杆Block 分段AM 上午PM 下午Main deck 主甲板Keel （船舶）龙骨Notification of inspection 检查验收通Upper deck 上甲板Bilge keel 舭龙骨知单Poop deck 艉楼甲板Power tool 带动力工具（风动或电动）Application 申请，申请单Accommodation deck 生活甲板Welder 电焊工Inspection 检验，报验Compass deck 罗经甲板Welding machine 电焊机Technical discussion 技术讨论Funnel 烟囱 A.C welding 交流（电弧）焊On board 在船上Bridge 桥楼，驾驶台 D.C welding 直流（电弧）焊In the workshop 在车间Bridge wing 驾驶室翼桥Grinding 打磨On the slipway 在船台上Wheel house 驾驶室Welding 电焊At pier(wharf) 在码头Engine room 机舱Spatters 飞溅（电焊）Fair 尚好的Engine control room 机舱集控室Under out 咬口The performance is merely fair 性能尚Catwalk 天桥、步桥Sharp edge 快口好Flying bridge （露天）航行驾驶室 2 船舶专业英语词汇（初级）Terrible 极坏的，很糟的Rescue boat 救助艇Deflection 挠曲，变形So so 马马虎虎Life boat 救生艇Slags 渣Welding slags 电焊渣Semi-conductor 半导体Touch-up painting 补漆、点漆Automatic welding 自动焊Rectifier 整流器First coat 底漆、头道漆Manual welding 手工焊Transformer 变压器Finish coat 面漆Arc welding 电弧焊Thermostat 恒温器Surface coat 表面涂层Gas shielded welding 气体保护焊Thermister 热敏器Under coat 内涂层Inter gas arc welding惰性气体保护电弧Edison base 螺丝灯座、爱迪生灯座Wearing coat 磨耗层焊Bayonet base卡口灯座Zinc-rich coating 富锌涂层Welding seam焊缝On-off 开关（量）Cement wash coating（薄）水泥涂层Bending machine 弯曲机Analogue 模拟，模拟设备Stripe coating 预涂层Three-roll bending machine 三芯弯板机Active analogue 有源模拟、主动模拟Floor covering 地板覆层Torsional box 抗扭箱Passive analogue无源模拟、被动模拟Alkyd resin paint 醇酸树脂漆Void space空舱Dry contact 无源模拟、干接触Epoxy(resin-based)paint 环氧树脂涂料Cofferdam 隔离舱Buzzer 蜂鸣器 3 船舶专业英语词汇（初级）Bulwark 舷墙，防浪板Button 按扭，电扭Scuttle 舷窗Wall 墙壁Switch 开关Carpet 地毯Floor 地板Main switch 主开关Wooden skirt 木裙板（踢脚）Controllable pitch 可调桨Main switch board 主配电板Aluminum skirt 稆质裙板（踢脚）Elastic coupling 弹性联轴节Cable 电缆Brass nose装于楼梯踏步一的黄铜防滑Bellow 波纹管Wire 电线镶条Joint 接头Three-core cable 三蕊电缆Stainless screw不锈钢螺钉Gaskets垫片Clamp 夹钳、夹具Spring 弹簧Fitting bolts 拂螺拴Clip 接线柱、线夹Securing dev ice 固定件Chock 制动块、导缆器Alligator clip 鳄鱼夹、弹簧夹Locking device 闭锁装置，制动设备Chock fast 环氧垫块Voltage drop 电压降Plywood 胶合板，层压板Foundation 底座、基座Speed droop速度降低Laminated plate 迭层板Mounting 装置、座、架Black out 黑灯试验Laminate 层压制品，迭层板，层压板Mount （常指火炮等武器的）座，架Power failure 失电High pressure washing of the hull 用高Vent pipe 透气管Setting point 设定点压水冲洗船壳Sounding pipe 探测管Adjust 调正（v）Steel plate temperature 钢板温度Vapour return line 油气回路管Adjustment 调正（n）Condensation 冷凝Stripping line 扫舱管Oscillator 振荡器、振动器Capillary condensation 毛细管现象Safety equipment 安全设备Oscilloprobe 示波器测试头Dew point 露点Life-saving equipment 救生设备Oscilloscope 示波器、示波仪Flashing point 闪点Cargo hold 货舱Resistor 电阻、电阻器Ignition point 燃点，着火点Cargo oil tank 货油舱Potentiometer 电位器、电势计Ventilation for coating 涂装通风Cabin 船舱、舱室Electrolysis 电解（作用）Dehumidifier 去湿机，干燥机Room 房间Electrolyte 电解质、电解液Dehumidification 去湿，去潮Store room 储藏室setting point of power surplus 负载余量Sagging 流挂，下垂Cold room 冷库Chalking 粉化设定值Fish room 鱼库Peeling 剥落（指油漆）重载询问Meat room 肉库test the power surplus setting point 重载Pinhole 针孔Provision room 粮库Cure询问试验Foam room 泡沫库4）漆、木Curing 硬化，熟化，硫化CO2 room 二氧化碳室Surface preparation 表面处理（清理工Drying film thickness(DFT) 干膜（漆膜）Pump room 泵室作）厚度Battery room 蓄电池室Blasting equipment 喷漆（砂粒）装置Curing temperature 硬化、固化温度Radio room 报务室Sand blasting 喷砂除锈Power tools 有动力的工具（包括电动及Galley 厨房Pre-blasting 预喷砂风动）Ventilation system 通风系统Lingt blasting 预喷砂Pheomatic tools 风动工具Fresh water piping system 淡水系统Full blasting 通喷砂Burnt area 烧坏的区域Sea water piping system 海水管系Sand sweep扫砂Oil stains 油迹Water jacket 水套Sand blasting to SA2.5 喷砂达到SA2.5 Scratches划痕Insulation materials 绝缘材料Damaged places遭损坏的部位级Lagging 绝缘材料、外套（锅炉、管子Steel work inspection after full blasting Chicken wire 钢丝网等）通喷砂后钢结构检查Tiles 瓷砖，瓦3）电器Cleanliness inspection 清洁度检查Mosaic-tile 彩色瓷砖，镶嵌瓷砖，马赛Current 电流Inspection after degreasing除去油脂后克瓷砖Voltage 电压Glue 胶，粘结剂检查Frequency 频率Removing oil stains by detergent/solvent Silica 硅石，二氧化碳Contact 触点、触头使用洗洁剂/容剂除去油迹Silicagel 硅胶Ballast 镇流器Shop primer 车间底漆Decoration 装饰，装修Convertor 变频器、换能器Spray painting 喷漆、喷涂法Interior decoration 内部装饰，内装Conductor 导体Touch-up 补漆、修正Deck head 天花板Ceiling 天花板Pipe spanner管子扳手Hydraulic nuts 液压螺帽Paneling 板墙，镶板Reamer 铰刀Rudder 舵Wall 墙壁Reaming （用）铰（刀扩）孔Rudder bl ade 舵叶Desk 书桌，桌台Countersink reamer 锥形孔铰刀Propeller 车叶，螺旋桨Drawer 抽屉Wrench 扳手，扳头Fixed pitch propeller 固定螺距的螺旋桨Catch hook 固定钩子Shisel 凿子Lofting 型线图放样Observation window 观察窗Calipers 卡钳，两脚规Lay off （船及部件）放样，下料Inspection window 检查孔窗Inside calipers 内卡钳Plate-cutting 钢板下料，开工Clear view window 旋转观察窗Bore 内孔Numerically-controlled cutting machine Curtain 窗帘Boroscopic inspection 内孔表面检查数控切割机Latch 止动销，插销Boroscope 内孔表面检查仪Cutting machine 切割机Valance窗帘箱Plug 塞（子），（内燃机）火花塞Under water plasma cutting machine 水Hanging 窗帘Cock 施塞，龙头下等离子切割机Eyebrow 舷窗眉板Valve 阀Surface preparation表面处理Pre-alarm 预报警P/V valve P/V 阀Fabrication（焊）开坡口，边缘加工（如Trip 脱扣，跳闸Strainer 滤器刨边）Preferential trip 优先脱扣Coarse strainer粗滤器Upside down construction method 分段Transducer换能器Fine strainer 精滤器装配synchronize（便）同步Oil separator 分油机Assembly 反身建法synchronize motor 同步电机Back pressure背压Erection 装配，大合拢synchronous motor 异步电机Pressure test压力试验Jig 装配架，胎架step motor 步进电机Over speed 超速Bow jip 船首部胎架diode 二极管Over load 超负荷Girder 纵向构件，桁（材）triode 三极管Dafety device 安全装置Beam 梁，横梁audion 三极管Fly wheel 飞轮Sections型材single phase单相Floating floor 浮式地板Profile 型钢（条）three phase三相Deckhead 天花板（指由甲板形成的）Bar 杆，棒,棒材phase-in逐步引进Ladder 梯子Plate 板材phase-shafting相移Vertical ladder 直梯Angle bar 角钢retarding phase 滞后相位Inclined ladder 斜梯I beam（窄缘）工字梁reversed phase倒相，相反Accommodation ladder 舷梯H beam（宽缘）工字梁relay 继电器Pilot ladder 引水员；软梯Stiffener 扶强材timer 定时器Centering 对中心Bracket 托架，支架，肘板trimmer 微调电容器，调正片Alignment 对准，对准中心Support 支架delay 延时Inspection 报验Frame 肋骨，框架carrier 载波，载波电流Installation 安装Douler 复板transponder发射器，应答器，询问机Final inspection of M/E insallation 主机Coaming（舱口）围板，缘材echo-sound回声测深仪Sinp 剪切最终安装报验radio navigation equipment 无线电导航Inspection of the centering of the stern Cut 切割设备tabe before fine boring 精镗前艉轴管中Anchor 锚log 计程仪Anchor widdlass 锚机心校准auto-pilot 自动驾驶仪Alignment check/inspection 拉中心/校Anchorage 锚位，锚地gyro-compass 电罗经Chain 链正报验barrier 屏障，障碍，栅栏Completeness inspection of the thermal Chain block 链条滑车，神仙滑车zenner barrier齐纳屏（使电只能单向流oil circulating piping system 热油循环Platform 平台的半导体）管系完整性报验Crossover 跨越（梯桥），立交radio beacon无线电信标Cleanliness inspection after flushing F.O Life raft 救身筏pluse脉冲piping system 燃油管串油后清洁检查Life buoy 救生圈blanking plus 消隐脉冲Function test of steering gear舵机效甩Forward winch 前绞缆机induction 感应，感应现象After winch 后绞缆机试验oscillation 振荡Hose test of water tight doors 水密门冲Windlass 锚机Leak(v)渗，漏Bitt 带缆桩，系桩水试验Leakage(n) 渗，漏Noise lever measurement噪声测量Fairlead 导缆钳，导缆孔Overhaul 大修，彻底检修Vibration level measurement 振动测量Hand rail 扶手，栏杆Hammer 榔头Main engine (M/E) 主机Beam 横梁Spanner扳手，扳头Generator 发电机Frame 肋骨，框架Ring spanner环形扳手，梅花扳手Emergency generator应急发电机Scantling 构件尺寸Allen key 内六角扳手，Shaft generator轴带发电机Cargo oil tank 货油舱Box spanner 套筒扳手Fresh water generator 制淡装置Scantling draft 结构吃水Torque spanner扭力扳手Steering gear 舵机Forepeak tank首尖舱Double-ended spanner双头扳手General service pump 总用泵After peak tank 尾尖舱Monkey spanner 活络扳手，活络管扳手Pire pump 消防泵Water ballast tanks(W.B.T)压载水舱Shifting spanner 活络扳手Hydraulic motor 液压马达Fuel oil tank(F.O.T) 燃油舱Lubricating oil tank(L.OT) 滑油舱Negotiation 谈判ball bearing 滚珠轴承Diesel oil tank(D.O.T) 柴油舱Agreement 协议ball valve 球阀Double botton 双层底Shipyard 船厂ballast tank 压载水舱Double skin 双层外板，双层蒙皮bar 型材船舶专业英语词汇Bow thruster 艏侧推bar keel 棒龙骨，方龙骨，矩形龙骨船舶专业英语词汇（按照字母顺序排Propeller 车叶barge 驳船列）（一）Fixed pitch propeller 定螺距螺旋桨baseline 基线Controllable pitch propeller(CPP) 可调螺 a faired set of lines 经过光顺处理的一basic design 基本设计距螺旋桨套型线batten 压条，板条Shaft 轴 a stereo pair of photographs 一对立体beam 船宽，梁Tail shart 尾轴beam bracket 横梁肘板投影相片Shaft generator 轴带发电机abaft 朝向船体beam knee 横梁肘板Watertight doors 水密门abandonment cost 船舶废置成本费用bed-plate girder 基座纵桁Bulwark 舷墙accommodation 居住（舱室）bending-moment curves 弯矩曲线Bulkhead 舱壁accommodation ladder 舷梯Benoulli ’s law 伯努利定律Tank top 内底，液舱顶adjust valve 调节阀berth term 停泊期Hatch cover 舱口盖adjustable-pitch 可调螺距式bevel 折角Manhole 人孔admiralty 海军部bidder 投标人Fin stablizer 减摇鳍advance coefficient 进速系数bilge 舭，舱底Antifouling system 防海生物的，防污染aerostatic 空气静力学的bilge bracket 舭肘板系统aft peak bulkhead 艉尖舱壁bilge radius 舭半径Ship 船aft peak tank 艉尖舱bilge sounding pipe 舭部边舱水深探Vessel船，舰aileron 副鳍管Fabrication 制造，分段装配air cushion vehicle 气垫船bitt 单柱系缆桩（precfabrication 预制，预加工）air diffuser 空气扩散器blade root 叶跟Assemble 装配，组装air intake 进气口blade section 叶元剖面Erection 大合拢，船台装配aircraft carrier 航空母舰blast 喷丸Staging 脚手架air-driven water pump 气动水泵block coefficient 方形系数Block stage 分段阶段airfoil 气翼，翼剖面，机面，方向舵blue peter 出航旗Mile stone（里程碑，大节点）alignment chock 组装校准用垫楔boarding deck 登艇甲板Plate-cutting 下料，开工aluminum alloy structure 铝合金结构boat davit 吊艇架Keel-laying 上船台，龙骨铺设American Bureau of Shipping 美国船boat fall 吊艇索Lauching 下水boat guy 稳艇索级社mooring trial 码头试验，系泊试验amidships 舯bobstay 首斜尾拉索sea trial(sea)试航amphibious 两栖的body plan 横剖面图delivery of the ship 交船anchor arm 锚臂bolt 螺栓，上螺栓固定defect list by the owner/society 船东提anchor chain 锚链Bonjean curve 邦戎曲线出的消除意见清单/船级社提出的消除anchor crown 锚冠boom 吊杆意见清单anchor fluke 锚爪boss 螺旋桨轴榖design stage设计阶段anchor mouth 锚唇bottom side girder 旁底桁submit drawings to owner,classification anchor recess 锚穴bottom side tank 底边舱society(LR、DNV 、BV 、ABS ，etc)for anchor shackle 锚卸扣bottom transverse 底列板approval 向船东，船级社（劳氏，挪威，anchor stock 锚杆boundary layer 边界层法国，美国等）提交认可图纸angle bar 角钢bow line 前体纵剖线hull workshop 船体车间angle of attack 攻角bow wave 艏波machining workshop 金工车间angle plate 角钢bowsprit 艏斜桅machinery engineering workshop轮机车angled deck 斜角甲板bow-thruster 艏侧推器间anticipated loads encountered at sea 在box girder 箱桁electrical workshop 电气车间bracket floor 框架肋板波浪中遭遇到的预期载荷business dept.经营处anti-pitching fins 减纵摇鳍brake 制动装置perchasing dept.供应处antiroll fins 减摇鳍brake band 制动带Q.C.Dept.检验处anti-rolling tank 减摇水舱brake crank arm 制动曲柄Design dept.设计室appendage 附体brake drum 刹车卷筒Painting and carpenter’s workshop 漆木artisan 技工brake hydraulic cylinder 制动液压缸车间assembly line 装配流水线brake hydraulic pipe 刹车液压管Project manager项目经理at-sea replenishment 海上补给breadth extreme 最大宽，计算宽度Director 指导者，厂长，董事augment of resistance 阻力增额breadth moulded 型宽Managing director 执行董事，常务董事，auxiliary systems 辅机系统breakbulk 件杂货总经理auxiliary tank 调节水舱breasthook 艏肘板Head首长，团长，主任axial advance 轴向进速bridge 桥楼，驾驶台Manager经理，管理人，干事backing structure 垫衬结构bridge console stand 驾驶室集中操作Leader 领导者back-up member 焊接垫板台Meeting 会议balance weight 平衡锤BSRA 英国船舶研究协会buckle 屈曲clipper bow 飞剪型船首dimensionless ratio 无量纲比值buffer spring 缓冲弹簧clutch 离合器displacement 排水量built-up plate section 组合型材coastal cargo 沿海客货轮displacement type vessel 排水型船bulb plate 球头扁钢cofferdam 防撞舱壁distributed load 分布载荷bulbous bow 球状船艏，球鼻首combined cast and rolled stem 混合型division 站，划分，分隔bulk carrier 散货船do work 做功艏柱bulk oil carrier 散装油轮commercial ship 营利用船dock 泊靠bulkhead 舱壁commissary spaces 补给库舱室，粮食double hook 山字钩bulwark 舷墙double iteration procedure 双重迭代法库bulwark plate 舷墙板common carrier 通用运输船double roller chock 双滚轮式导览钳bulwark stay 舷墙支撑commuter 交通船double-acting steam cylinder 双向作buoy tender 航标船compartment 舱室用的蒸汽气缸buoyant 浮力的compass 罗经down halyard 降帆索buoyant box 浮箱concept design 概念设计draft 吃水Bureau Veritas 法国船级社connecting tank 连接水柜drag 阻力，拖拽力butt weld 对缝焊接constant-pitch propeller 定螺距螺旋桨drainage 排水butterfly screw cap 蝶形螺帽constraint condition 约束条件draught 吃水，草图，设计图，牵引力buttock 后体纵剖线container 集装箱dredge 挖泥船by convention 按照惯例，按约定containerized 集装箱化drift 漂移，偏航大秦contract design 合同设计drilling rig 钻架cable ship 布缆船contra-rotating propellers 对转桨drillship 钻井船cable winch 钢索绞车controllable-pitch 可控螺距式drive shaft 驱动器轴CAD(computer-aided design) 计算机辅corrosion 锈蚀，腐蚀driving gear box 传动齿轮箱助设计couple 力矩，力偶driving shaft system 传动轴系CAE(computer-aided manufacturing) crane 克令吊，起重机dry dock 干船坞计算机辅助制造crank 曲柄ducted propeller 导管螺旋桨CAM(computer-aided engineering) 计crest (of wave) 波峰dynamic supported craft 动力支撑型算机辅助工程crew quarters 船员居住舱船舶camber 梁拱criterion 判据，准则dynamometer 测力计，功率计cant beam 斜横梁Critical Path Method 关键路径法 e.h.p 有效马力cant frame 斜肋骨cross-channel automobile ferries 横越eccentric wheel 偏心轮cantilever beam 悬臂梁echo-sounder 回声探深仪海峡车客渡轮capacity plan 舱容图cross-sectional area 横剖面面积eddy 漩涡CAPP(computer –aided process crow’s nest 桅杆瞭望台eddy-making resistance 漩涡阻力planning) 计算机辅助施工计划制定cruiser stern 巡洋舰尾efficiency 供给能力，供给量capsize 倾覆crussing range 航程electrohydraulic 电动液压的capsizing moment 倾覆力臂cup and ball joint 球窝关节electroplater 电镀工captain 船长curvature 曲率elevations 高度，高程，船型线图的侧captured-air-bubble vehicle 束缚气泡curves of form 各船形曲线面图，立视图，纵剖线图，海拔减阻船cushion of air 气垫empirical formula 经验公式cargo cubic 货舱舱容，载货容积damage stability 破损稳性enclosed fabrication shop 封闭式装配cargo handling 货物装卸damper 缓冲器车间carriage 拖车，拖架damping 阻尼enclosed lifeboat 封闭式救生艇cast steel stem post 铸钢艏柱davit arm 吊臂end open link 末端链环catamaran 高速双体船deadweight 总载重量end shackle 末端卸扣catamaran 双体的de-ballast 卸除压载endurance 续航力cavitation 空泡deck line at side 甲板边线endurance 续航力，全功率工作时间cavitation number 空泡数deck longitudinal 甲板纵骨engine room frame 机舱肋骨cavitation tunnel 空泡水筒deck stringer 甲板边板engine room hatch end beam 机舱口端center keelson 中内龙骨deck transverse 强横梁梁centerline bulkhead 中纵舱壁deckhouse 舱面室，甲板室ensign staff 船尾旗杆centroid 型心，重心，质心，矩心deep v hull 深v 型船体entrance 进流段chain cable stopper 制链器delivery 交船erection 装配，安装chart 海图depth 船深exhaust valve 排气阀charterer 租船人derrick 起重机，吊杆expanded bracket 延伸肘板chief engineer 轮机长design margin 设计余量expansion joint 伸缩接头chine 舭，舷，脊design spiral 设计螺旋循环方式extrapolate 外插chock 导览钳destroyer 驱逐舰fair 光顺CIM(computer integrated manufacturing) detachable shackle 散合式连接卸扣faised floor 升高肋板计算机集成组合制造detail design 详细设计fan 鼓风机circulation theory 环流理论diagonal stiffener 斜置加强筋fatigue 疲劳classification society 船级社diagram 图，原理图，设计图feasibility study 可行性研究cleat 系缆扣diesel engine 柴油机feathering blade 顺流变距桨叶fender 护舷gradient 梯度imperial unit 英制单位ferry 渡轮，渡运航线graving dock 槽式船坞in strake 内列板fillet weld connection 贴角焊连接Green Book 绿皮书，19 世纪英国另inboard profile 纵剖面图fin angle feedback set 鳍角反馈装置incremental plasticity 增量塑性一船级社的船名录，现合并与劳埃德船fine fast ship 纤细高速船independent tank 独立舱柜级社，用于登录快速远洋船fine form 瘦长船型gross ton 长吨（1.016 公吨）initial stability at small angle of finite element 有限元group technology 成祖建造技术inclination 小倾角初稳性fire tube boiler 水火管锅炉GT 成组建造技术inland waterways vessel 内河船fixed-pitch 固定螺距式guided-missile cruiser 导弹巡洋舰inner bottom 内底flange 突边，法兰盘gunwale 船舷上缘in-plane load 面内载荷flanking rudders 侧翼舵gunwale angle 舷边角钢intact stability 完整稳性flap-type rudder 襟翼舵gunwale rounded thick strake 舷边圆intercostals 肋间的，加强的flare 外飘，外张International Association of弧厚板flat of keel 平板龙骨guyline 定位索Classification Society (IACS) 国际船级fleets of vessels 船队gypsy 链轮社联合会flexural 挠曲的gyro-pilot steering indicator 自动操舵International Towing Tank Conference floating crane 起重船(ITTC) 国际船模试验水池会议操纵台floodable length curve 可进长度曲线gyroscope 回转仪intersection 交点，交叉，横断（切）flow of materials 物流qaspt 2006-07-17 18:29 inventory control 存货管理flow pattern 流型，流线谱iterative process 迭代过程船舶专业英语词汇（按照字母顺序排flush deck vessel 平甲板型船jack 船首旗列）（四）flying bridge 游艇驾驶台half breadth plan 半宽图jack 千斤顶flying jib 艏三角帆half depth girder 半深纵骨joinery 细木工folding batch cover 折叠式舱口盖half rounded flat plate 半圆扁钢keel 龙骨folding retractable fin stabilizer 折叠收hard chine 尖舭keel laying 开始船舶建造放式减摇鳍hatch beam sockets 舱口梁座kenter shackle 双半式连接链环following edge 随边hatch coaming 舱口围板Kristen-Boeing propeller 正摆线推进器following ship 后续船hatch cover 舱口盖landing craft 登陆艇foot brake 脚踏刹车hatch cover 舱口盖板launch 发射，下水fore peak 艏尖舱hatch cover rack 舱口盖板隔架launch 汽艇forged steel stem 锻钢艏柱hatch side cantilever 舱口悬臂梁launching equipmeng 向水中）投放设备forging 锻件，锻造hawse pipe 锚链桶LCC 大型原油轮forward draft mark 船首水尺hawsehole 锚链孔leading edge 导缘，导边forward/afer perpendicular 艏艉柱heave 垂荡ledge 副梁材forward/after shoulder 前/后肩heel 横倾length overall 总长foundry casting 翻砂铸造heel piece 艉柱根leveler 调平器，矫平机frame 船肋骨，框架，桁架helicoidal 螺旋面的，螺旋状的life saving appliance 救生设备freeboard 干舷hinge 铰链lifebuoy 救生圈freeboard deck 干舷甲板hinged stern door 艉部吊门lifejacket 救生衣freight rate 运费率HMS 英国皇家海军舰艇lift fan 升力风扇fresh water loadline 淡水载重线hog 中拱lift offsets 量取型值frictional resistance 摩擦阻力hold 船舱light load draft 空载吃水Froude number 傅汝德数homogeneous cylinder 均质柱状体lightening hole 减轻孔fuel/water supply vessel 油水供给船hopper barge 倾卸驳light-ship 空船full form 丰满船型horizontal stiffener 水平扶强材limbers board 舭部污水道顶板full scale 全尺度hub 桨毂，轴毂，套筒liner trade 定期班轮营运业fullness 丰满度hull form 船型，船体外形lines 型线funnel 烟囱hull girder stress 船体桁应力lines plan 型线图furnishings 内装修HVAC(heating ventilating and cooling) Linnean hierarchical taxonomy 林式等gaff 纵帆斜桁取暖，通风与冷却级式分类学gaff foresail 前桅主帆hydraulic mechanism 液压机构liquefied gas carrier 液化气运输船gangway 舷梯hydrodynamic 水动力学的liquefied natural gas carrier 液化天然gantt chart 甘特图hydrofoil 水翼气船gasketed openings 装以密封垫的开口hydrostatic 水静力的liquefied petroleum gas carrier 液化石general arrangement 总布置IAGG(interactive computer graphics)油气船general cargo ship 杂货船liquid bulk cargo carrier 液体散货船交互式计算机图像技术generatrix 母线icebreaker 破冰船liquid chemical tanker 液体化学品船geometrically similar form 外形相似icebreaker 破冰船list 倾斜船型IMCO(Intergovernmental Maritime living and utility spaces 居住与公用舱girder 桁梁，桁架Consultative Organization) 国际海事室girder of foundation 基座纵桁Lloyd ’s Register of shipping 劳埃德。
船舶专业英文词汇
船舶专业英文词汇
augment of resistance 阻力增额 auxiliary systems 辅机系统 auxiliary tank 调节水舱 axial advance 轴向进速 backing structure 垫衬结构 back-up member 焊接垫板 balance weight 平衡锤 ball bearing 滚珠轴承 ball valve 球阀 ballast tank 压载水舱 bar 型材 bar keel 棒龙骨，方龙骨，矩形龙骨 barge 驳船 baseline 基线 basic design 基本设计 batten 压条，板条 beam 船宽，梁 beam bracket 横梁肘板 beam knee 横梁肘板 bed-plate girder 基座纵桁 bending-moment curves 弯矩曲线 Benoulli’s law 伯努利定律 berth term 停泊期 bevel 折角 bidder 投标人 bilge 舭，舱底 bilge bracket 舭肘板 bilge radius 舭半径 bilge sounding pipe 舭部边舱水深探管 bitt 单柱系缆桩 blade root 叶跟
/ShowPost.asp?ThreadID=519（第 5／31 页）2007-2-5 20:33:21
船舶专业英文词汇
CAE(computer-aided manufacturing) 计算机辅助制造 CAM(computer-aided engineering) 计算机辅助工程 camber 梁拱 cant beam 斜横梁 cant frame 斜肋骨 cantilever beam 悬臂梁 capacity plan 舱容图 CAPP(computer –aided process planning) 计算机辅助施工计划制定 capsize 倾覆 capsizing moment 倾覆力臂 captain 船长 captured-air-bubble vehicle 束缚气泡减阻船 cargo cubic 货舱舱容，载货容积 cargo handling 货物装卸 carriage 拖车，拖架 cast steel stem post 铸钢艏柱 catamaran 高速双体船 catamaran 双体的 cavitation 空泡 cavitation number 空泡数 cavitation tunnel 空泡水筒 center keelson 中内龙骨 centerline bulkhead 中纵舱壁 centroid 型心，重心，质心，矩心 chain cable stopper 制链器 chart 海图 charterer 租船人 chief engineer 轮机长 chine 舭，舷，脊 chock 导览钳 CIM(computer integrated manufacturing) 计算机集成组合制造
船舶专业英文词汇汇总
船舶专业英文词汇船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical ath Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇。
船舶专业英语词汇
船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船尾[adv][prep]abandonment cost 船舶废置成本费用accommodation 居住（舱室）living quarter accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯[adv]amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板Beacon 灯塔，示位标bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth molded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定、公约船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer租船人charterchief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室，间隔舱compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船throughoutdistributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠vtdouble hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水，草图，设计图drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak tank 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forgeforward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修furniture gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipment （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse)纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性section moulus 剖面模数sections 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机bow 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮very large crude carrierVoith-Schneider propeller/ propulsion外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity/integrality 水密完整性integrate 整合completeness wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工melterwetted surface 湿表面积winch 绞车mooring winchwindlass 起锚机anchor windlasswing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇二．轮机1． Inspection machining dimension of propeller shaft(intermediate shaft or counter shaft).螺旋桨轴（中间轴）机加工尺寸检查。
船舶专业英语词汇表
2006-8-11 16:321、1结构 Structure船厂 dockyard/shipyard 船坞 dock/boatyard船东 ship-owner 船舷 Ship's side船舱 hold 甲板 Deck船籍 Ship's registry 住舱甲板 accommodation deck 船首 bow 梁拱甲板 arch deck船尾 stern 首楼甲板 Forecastle deck2船坞 dock/boatyard船舷 Ship's side船的栏杆 Ship's rail甲板Deckeck梁拱甲板 arch deck载货甲板 cargo deck首楼甲板 Forecastle deck上甲板 Upper deck下甲板 Lower deck货舱甲板 Hold deck桥楼甲板 Bridge deck水密甲板 Watertight deck3艇甲板 Boat deck罗经甲板 Compass deck板 Plate舭板 Bilge plate船首外板 Bow plate肘板 Bracket plate舱壁板 Bulkhead plate槽形舱壁板 Corrugated bulkhead plate铜-钢复合板 Copper sheathing steel plate 甲板边板 Deck stringer plate斜板 Sloping plate加强板 Reinforcement plate平台 platform机舱平台 Engine-room platform分段 Block首段 Bow block中段 Midship block5尾段 Stern block左舷 port右舷 Starboard甲板纵桁 Deck girder横桁 Cross girder水平桁 Horizontal girder舱口边梁 Hatch coaming girder机座纵桁 Engine girder6甲板下纵桁 Underdeck girderframe船底肋骨 Bottom frame首肋骨 Bow frame肘板框架肋骨 Bracket frame球鼻首肋骨 Bulbous bow frame球曲型肋骨 Bulbous frame主肋骨 Chief frame首肋骨 Fore frame7桁架梁 me 甲板纵桁 Deck longitudinal横框架肋骨 Transverse frame 内底纵桁/纵骨 Inner bottom longitudinal肋距 F.S.(frame space) 舷侧纵桁/纵骨 Shell side longitudinal纵桁/纵骨/纵向构件 longitudinal 双层底顶纵骨 Top longitudinal of doublebottom8斜舱壁纵骨 Slopping-bulkhead longitudinal 舱 Tank结构 Structure 尾尖舱 after peak tank附属结构 Accessory structure 尾部水舱 after water tank全焊结构 All-welded structure 辅助水柜 Auxiliary water tank structure 底舱 Bottom tank船首部结构 Bow structure 底边舱 Bottom side tank支撑结构 Braced structure 货油压载舱 Cargo and ballast tank桥楼结构 Bridge structure 循环水槽 Circulating flow water tank首楼结构 Foreca人孔 manhole 干舱 Dry tank9舱 Tank尾尖舱 after peak tank尾部水舱 after water tank辅助水柜 Auxiliary water tank辅助压载水舱 Auxiliary water ballast tank污and ballast tank循环水槽 Circulating flow water tank循环滑油舱 Circulating lubricating oil tank构架结构 Framed structure纵桁结构 Girder structure人孔 manhole10k应急淡水柜 Emergency fresh water tank首舱 Fore tank首尖舱 Fore peak tank斜边舱 Hopper side tank液舱 Liquid tank龙骨舱 Keel tank右舷舱 Starboard tank顶边水舱 Topside tank顶边翼舱 Topside wing tank小舱口盖 Small hatch cover水密舱口盖 Water-tight small hatch cover风雨密舱口盖 Weather-tight small hatch cover页面功能【字体：大中小】【打印】【关闭】dugout独木舟barge驳船kayak（爱斯基摩人的）木排outrigger桨叉架船rowing boat划艇（美作：rowboat）gondola（意大利的）长平底船whale mother ship捕鲸母船hydrofoil水翼船catamarans双体船dredger挖泥船boat船brig， brigantine双桅船canoe小船，独木舟caravel快帆船cargo boat货船coaster近海贸易货船cod-fishing boat捕鳕鱼船whaler捕鲸船collier运煤船battleship战船shallop小型战船coastguard cutter， coastguard vessel巡逻艇，缉私艇revenue cutter缉私船patrol boat巡逻艇minelayer布雷艇minesweeper扫雷艇torpedo boat鱼雷艇frigate轻护航舰gunboat炮舰submarine潜水艇destroyer驱逐舰corvette轻巡洋舰cruiser巡洋舰aircraft carrier航空母舰ferry， ferryboat渡船，渡轮fishing boat渔船freighter货船galleon大型帆船galley大划桨船hovercraft气垫船icebreaker破冰船launch艇lifeboat救生艇lighter驳船liner， ocean liner远洋班轮merchant ship， merchantman商船motorboat摩托艇outboard尾部装有马达的小艇paddle steamer， paddle boat明轮船passenger boat客船piragua， pirogue独木舟raft木筏rowing boat划艇sailing boat， sailing ship帆船schooner纵帆船ship船skiff小艇sloop单桅船steamer， steamship汽轮tanker油轮trawler拖网渔船tug， tugboat拖轮vessel船yacht游艇yawl船载小艇船舶英语自动雷达标绘仪Automatic radar plotting aid 自动电话Automatic telephone电压自动调节器Automatic voltage regulator 自动化系统Automation system压载控制台Ballast control console镇流器Ballast底座Base电池Battery铃Bell弯曲Bend床头灯Berth light失电Black out刹车Brake电刷Brush船舶英语3球鼻首警告灯Bulbous bow warning light 汇流排Bus(-)bar汇流排Bus –tie –in蜂鸣器BuzzerC、电缆Cable电缆填料函Cable gland敷设电缆Cable laying电缆管Cable pipe (conduit)电缆扎带Cable strap电缆托架Cable tray校准器Calibrator电容capacitor阴板Cathode警告牌Caution plate船舶英语4顶灯Ceiling light中央处理器Central processing unit通道Channel充电器Charger充放电板Charging&discharging board 海图灯Chart table light检查Check芯片Chip清洁Clean雨雪清除器Clear view screen二氧化碳释放报警CO2 release alarm 同轴电缆Coaxial cable线圈Coil冷库呼叫Cold store calling船舶英语5通讯Communication计算机Computer接头Connector恒电流Constant current消耗Consumption触头Contact接触器Contactor控制箱Control box控制箱Controller芯线Core角灯Corner light计算器Counter电流CurrentD、损坏Damage船舶英语6危险气体报警箱Dangerous gas detecting &alarm box 白昼信号灯Daylight signal light去耦Decoupling set台灯Desk light控测器Detector拨号Dial数字选择呼叫收信机Digital select –call receiver调光器dimmer直流电Direct current直接起动Direct –on –line starting磁盘Disk显示Display遇险信息控制器Distress message controller多普勒记程仪Doppler speed log船舶英语7双极单刀开关Double pole single way switch双极双刀开关Double pole two way switch天线收发转换开关Duplexer值班水手呼叫Duty sailor calling接地Earth接地排Earth bar测深仪Echo sounder电工试验板Electric test panel电机员Electrical engineer电极Electrode应急照明分电箱Emergence lighting distribution box应急示位标Emergence position indicating radio beacon 应急停Emergence stop船舶英语8应急配电板Emergency switch board机舱报警Engine alarm集控台Engine control console机舱监测报警Engine room monitoring &alarm system 轮机员呼叫Engineer calling panel轮机员安全Engineer safety system增强群呼叫收讯机Enhance group call receiver交换机Exchanger防爆灯Explosion proof light延伸报警板Extension alarm panel故障Failure故障Fault反馈Feed back船舶英语9馈电品Feeder panel滤波器Filter火警复显器Fire alarm repeater防火风闸控制单元Fire damper control unit火警检测箱Fire detecting box火焰探头Flame detector闪光灯Flash light浮充电Float charge强光灯Flood light流程图Flow chart流量开关Flow switch荧光灯Fluorescent light雾笛Fog horn频率Frequency船舶英语10熔丝Fuse填料Gasket通用报警General alarm发电机Generator发电机屏Generator panel（铜）锣、钟Gong全球卫星定位导航GPS navigator 组合灯板Group alarm light pillar 组合起动屏Group starter panel 电罗经Gyro compass卤素灯Halogen light听筒Handset硬件Hardware航向Headingcontinue很好，支持一下！汇流排Bus –tie –in 最好有图片Double pole single way switchvery usefull.very usefull.study itwhy do not you send in one note?very usefull.study it general alarm.通用报警very usefull.study Filter=滤波器and flow chart=流程图交换机=Exchanger ,studywhat is word to describe the ”显示器“？use display or not？页: [1] 2船舶英语手册10请给我看一下电站负荷平衡表。
船舶专用英语汇总
船舶专业英文词汇No.1船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇来自：navigation > 《ship》上一篇：船舶保安员工作要点下一篇：海洋运输常用英文缩略语转藏到我的图书馆献花(1) 分享到微信以文找文分享：人人网开心网搜狐微博推荐给朋友举报类似文章更多∙船舶专业英语词汇∙船体制图常用英中名词术语对照∙船舶英语(页1) - 设计学习- 千岛热线论....∙船体结构英语∙船舶英语手册1--5.word可编辑.∙Navis.gr - 3Examination Questions For...∙船舶图纸符号大全∙货运保险鉴定常用词汇. 专业.专注.。
船舶英语词汇
船舶英语词汇目录一、造船部分1、船体部分2、机舱部分3、电气部分4、船装部分二、造机部分三、修造部分一、造船部分1、HULL PART 船体部分1、 1 结构Structure 船厂dockyard/shipyard 船坞dock/boatyard 船东ship-owner 船舷Ship's side 船码头quay/dock 船的栏杆Ship's rail 船舱hold 甲板Deck 船籍Ship's registry 住舱甲板accommodation deck 船首bow 梁拱甲板arch deck 船梯ladder 载货甲板cargo deck 船尾stern 首楼甲板Forecastle deck 上甲板Upper deck 下甲板Lower deck 主甲板Main deck 货舱甲板Hold deck 桥楼甲板Bridge deck 水密甲板Watertight deck 驾驶甲板Navigation deck 铜-钢复合板Copper sheathing steel plate 艇甲板Boat deck 甲板边板Deck stringer plate 罗经甲板Compass deck 斜板Sloping plate 板Plate 加强板Reinforcement plate 舭板Bilge plate 舵板Rudder plate 船底板Bottom plate 舷侧外板Side plate 船外板Shell plate 裙板Skirt plate 船首外板Bow plate 首柱板Stem plate 肘板Bracket plate 首柱板Stern plate 舱壁板Bulkhead plate 平台platform 槽形舱壁板Corrugated bulkhead plate 机舱平台Engine-room platform 舷墙板Bulwark plate 分段Block 围板Coaming plate 首段Bow block 连续板Connection plate 中段Midship block 尾段Stern block 甲板下纵桁Underdeck girder 左舷port 舭纵桁Wing girder 右舷Starboard 支柱Pillar纵桁Girder肋骨Frame型材桁Bar girder基础台架Base frame 中底桁Bottom center girder 支架Bear frame 中内龙骨Bottom center line girder 舭肋骨Bilge frame 底桁材Bottom girder 船底肋骨Bottom frame 旁桁材Bottom side girder 首肋骨Bow frame 甲板纵桁Deck girder 肘板框架肋骨Bracket frame 横桁Cross girder 球鼻首肋骨Bulbous bow frame 水平桁Horizontal girder 球曲型肋骨Bulbous frame 舱口边梁Hatch coaming girder 主肋骨Chief frame 机座纵桁Engine girder 首肋骨Fore frame 桁架梁Girder frame 舭纵桁舭纵骨Bilge longitudinal 舯部肋骨Middle frame 船底纵骨/纵桁bottom longitudinal 尖舱肋骨Peak frame 船底腹板纵桁bottom web longitudinal 加强筋Stiffened frame 甲板纵桁Deck longitudinal横框架肋骨Transverse frame 内底纵桁/纵骨Inner bottom longitudinal 肋距F.S.(frame space) 舷侧纵桁/纵骨Shell side longitudinal纵桁/ 纵骨/纵向构件longitudinal 双层底顶纵骨Top longitudinal of double bottom 斜舱壁纵骨Slopping-bulkhead longitudinal 舱舷边舱Tank Wing tank 结构structure 尾尖舱after peak tank 附属结构Accessory structure 尾部水舱after water tank 全焊结构All-welded structure 辅助水柜Auxiliary water tank 中部结构Amidships structure 辅助压载水舱Auxiliary water ballast tank 泊位结构Berthing structure 污水舱Bilge tank 底部龙骨结构Bottom keel structure 底舱Bottom tank 船首部结构Bow structure 底边舱Bottom side tank 支撑结构Braced structure 货油压载舱Cargo and ballast tank 桥楼结构Bridge structure 循环水槽Circulating flow water tank 首楼结构Forecastle structure 循环滑油舱压载水舱Circulating lubricating oil tank Ballast water tank 构架结构Framed structure 清洁压载舱Clean ballast tank 纵桁结构Girder structure 冷凝水柜Condensate catch tank 人孔manhole 干舱Dry tank 饮用水舱Drinking water tank 密封圈Sealing ring 污水舱Bilge tank 铰链Hinge 应急淡水柜Emergency fresh water tank 把手Handle 首舱Fore tank 平衡块Balance block 首尖舱Fore peak tank 斜边舱Hopper side tank 1 、2 welding 焊接液舱Liquid tank 坡口groove 龙骨舱Keel tank 单面坡口Single groove 右舷舱Starboard tank 双面坡口Double groove 顶边水舱Topside tank I 形坡口Square groove 顶边翼舱Topside wing tank V 型坡口Single v groove 小舱口盖Small hatch cover U 型坡口Single u groove 水密舱口盖Water-tight small hatch coverX 形坡口Single v groove 风雨密舱口盖Weather-tight small hatch cover K 形坡口Single bevel grooveY 形坡口Single v groove with broad rood face 填充金属Filler metal 坡口面Groove face 热影响区Heat-affected zone(HAZ) 坡口角度Groove angle 过热区Overheated zone 焊缝倾角Weld slope 焊合线Bond line(fusion line) 接头根部Root of joint 焊接区Weld zone 根部间隙Root gap 焊缝区Weld metal area 钝边Root face 焊缝weld 焊接接头Welding joint 连续焊缝Continuous weld 对接接头Butt joint 断续焊缝Intermittent weld角接接头Corner joint 纵向焊缝Longitudinal weld T 形接头T-joint 横向焊缝Transverse weld 搭接接头Lap joint 对接焊缝隙Butt weld 十字接头Cross shaped joint 角焊缝Filled weld 母材Base metal(parent metal) 并列断续角焊缝Chain intermittent fillet 交错断续角焊缝Staggered intermittent fillet 弧焊整流器Arc welding rectifier 焊缝正面Face of weld 自动焊Automatic welding 焊缝背面Back of weld 埋弧自动焊Submerged arc welding 焊缝宽度Weld width 半自动焊Semi- automatic welding 焊缝长度Weld length 氩弧焊Argon-arc welding 焊缝余高Reinforcement 二氧化碳气体保护焊CO2 gas shielded arc welding 焊脚Leg(of a fillet weld) 氧乙炔焊Oxy-acetylene welding 焊脚长度Leg length 气割Gas cutting 套管接头Muff joint 碳弧气刨Carbon arc air gouging 手工电弧焊Manual arc welding(shielded metal arc welding) 水下切割Underwater cutting 直流电弧焊Direct current arc welding 等离子弧切割Plasma arc cutting 交流电弧焊alternating current arc welding 连续焊Continuous welding 弧焊变压器Arc welding transformer 断续焊Intermittent welding 点焊Sport welding 对接焊Butt welding 分段退焊Back step welding 角焊Fillet welding 分段多层焊Block welding 搭接焊Lap welding 深溶焊Deep penetrating welding 返修焊Re-welding 跳焊Skip welding 补焊Repair welding 陶质衬垫焊Ceramic backing welding 定位焊Tack welding 引弧Striking the arc 封底焊Back sealing welding 焊接工艺参数Welding condition 打底焊Backing welding 焊接电流Welding current 堆焊Surfacing(overlaying) 焊接电压Welding voltage 塞焊Plug welding 焊接速度Welding speed 槽焊Slot welding 电弧电压Arc voltage 盖面焊Consmetic welding 焊丝间距Wire spacing 前倾焊Forward welding 空载电压Open circuit voltage 后倾焊Backward welding 熔化速度Melting rate 送丝速度Wire feed rate 层间温度Inter-pass temperature 气体流量Gas flow rate 焊后热处理Post-weld heat treatment 焊丝伸出长度Wire extension 锤击Peening 极性Polarity 全焊透Full penetration welding 正极/ 阳极Positive electrode 熔池Weld-pool 负极/ 阴极Navigate electrode 熔深Penetration 左焊法Leftward welding 弧长Arc length 右焊法Rightward welding 喷射过渡Spray transfer电流密度Current density 短路过渡Short circuiting transfer 线能量Heat input 熔滴过渡Metal transfer 预热Preheat 焊缝成形Appearance of weld 后热Post-heat 焊缝成形系数Form factor of weld 预热温度Preheat temperature 熔敷系数Deposition coeffcient 后热温度Post-heat temperature 熔敷效率Deposition efficiency 熔合比Penetration ratio 立焊Vertical position welding 等速送丝Constant wire-feed system 仰焊Overhead position welding 变速送丝alternate wire-feed system 立向上焊Vertical up welding 电弧静特性Static characteristic of arc 立向下焊Vertical down welding电弧动特性dynamic characteristic of arc 单面焊Welding by one side焊接性试验Weldability test 双面焊Welding by both side 焊接结构Welded construction 单道焊Single-pass welding 焊道Bead 多道焊Multi-pass welding 焊层Layer 多层焊Multi-layer welding 正接(正极性) Straight polarity 焊接材料Consumables 反接(反极性) Reversed polarity 焊条Electrode 焊接位置Position of welding 焊条药皮Coating 平焊Flat position welding 酸性焊条Acid electrode 横焊Horizontal position welding 碱性焊条Basic electrode 低氢型焊条Low hydrogen typeelectrode 焊丝盘Wire reel 铁粉性焊条Iron power type electrode 铜冷却板Cu-cooling plate 重力焊条Gravity electrode 铜滑块Copper shoe 焊剂Flux 切割Cutting 熔炼焊剂Fused flux 焊接工作台Welding bench 烧结焊剂Sintered flux 焊接变位机Positioner 焊丝Wire 送丝机构Wire feeder 药芯焊剂Flux-cored wire 行走机构Traveler 保护气体Shielded gas 焊接车间Welding shop 焊剂垫Flux backing 引弧板Run-on tab(end tab) 重力焊条Gravity electrode 引出板Run-off tab(end tab) 焊剂漏斗Flux-hopper 定位板Strong-back 流量计Flow meter 焊接衬垫Welding backing 干燥箱Dryer 敲渣锤Chipping hammer 面罩Helmet 条虫状气孔Wormhole 焊工手套Welding glove 密集气孔Porosity 焊钳Electrode holder 针尖状气孔Pinhole 焊枪Welding gun 白点Fish eye (flake) 导电嘴Tip 切口Kerf 喷嘴Nozzle 咬边Undercut 焊矩Torch 焊瘤overlap 焊接缺陷Welding defect 凹坑Pit未焊透Incomplete penetration 烧穿Burn through 未熔合Incomplete fusion 未满焊Incomplete filled groove 渣Slag 清根Back chipping 夹渣Slag （slag inclusion）清渣Slag removal 夹杂物Inclusion 焊接烟尘Weld fume 气孔Blow hole 电光性眼炎Eye-flash 焊接性Weldability 横裂纹Transverse crack 碳当量Carbon equivalent 纵裂纹Longitudinal crack 未焊满Incomplete filled groove 焊趾裂纹Toe crack 焊接裂纹Weld crack 机械性能试验Mechanical property test 热裂纹Hot crack 试板Test piece 冷裂纹Cold crack 试样Specimen 氢致裂纹Hydrogen - induced crack 侧弯Side bend 延迟裂纹Delayed crack 弯曲Bending层状撕裂Lemellar tearing 横向拉伸Transverse tensile 弧坑裂纹Crater crack 宏观试样Macro-etching specimen 根部裂纹Root crack 微观试样Micro-examination specimen 再热裂纹Reheat crack 破断试验Fracture test 热影响区裂纹Heat-effected zone crack 抗裂试验Cracking test 晶间裂纹Intercystalline crack 脆性断裂Brittle fracture 塑性断裂Plastic fracture 焊接方法Welding process 焊接残余裂纹Welding residual stress 焊接工艺Welding technology 消除应力Stress relieving 焊接操作Welding operation 焊接变形Welding deformation 焊接顺序Welding sequence 角变形Angular distortion 焊接方向Direction of welding 外观检查Visual examination 常用缩语无损探伤Non-destruction testing（N.D.T.）气电立焊EGW 超声波探伤Ultrasonic inspection 药芯电弧焊FCAW 射线探伤（X 光）Radiographic inspection（X-rayinspection）实心电弧焊GMAW 磁粉探险伤Magnetic particle inspection 焊剂铜衬垫单面埋弧自动焊FCB渗透探伤Penetrate inspection 手工电弧焊SMAW 熔池Weld-pool 埋弧自动焊SAW 焊机（焊接电源）Weld source 钨极惰性气体保护电弧焊TIG 机舱部分ENGINE ROOM PART 熔化极惰性气体保护焊MIG 一、机舱设备Machines and equipment in engine room 活性气体保护焊MAG 1 、主机Main engine 手工电弧切割SMAC 1 ）主机油底壳The sump tank of M.E.2）主机飞轮Fly wheel of M.E3）活塞Piston2、发电机Generator engine1）应急发电机Emergency generator engine2）辅机Auxiliary3、锅炉Boiler1）组合锅炉The composite boiler2）锅炉安全阀The safety valve of boiler3）燃烧器Oil burner unit 3 ）主空气瓶Main air reservoir4）水位表Water level gauge 4 ）应急空气瓶Emergency air reservoir5）水位控制器Water level controller 5 、控制空气瓶Control air reservoir6）过量蒸气调节阀Excess steam pressure control valve6、空气干燥器Air dryer4、舵机7、分油机Oil purifier1）舵机间Steering room 1 ）燃油分油机Fuel oil purifier2）舵机装置Steering-gear 2）柴油分油机Diesel oil purifier3）手操舵装置Trick wheel plant 3 ）滑油分油机Lubricate oil purifier4）油缸Oil cylinder 4 ）排渣Sludge discharge5）反馈装置Feedback device 8、制淡装置Fresh water generator6）舵Rudder9、焚烧炉Incinerator舵叶Rudder blade10、油水分离器Oil water separator舵杆Rudder stock11、生活污水处理器Sewage treat plant上舵承Rudder carrier12、大气冷凝器Atmosphere condenser热水井Cascade and inspection（hotwell）5）主机燃油供给泵Main engine fuel oil supply pump 滑油自清滤器The automatic back-flash lubricating oil filter6）主机燃油增压泵Main engine fuel oil booster pump 燃油单元Fuel oil unit 7 ）主机十字头泵Main engine cross head pump1）主机燃油单元Fuel oil unit of M.E 8 ）付机海水泵Generator engine sea water pump2）付机燃油单元Fuel oil unit of A.E 9 ）付机缸套水泵Generator engine cylinder cooling water pump3）粘度计Viscosity controller 10 ）锅炉给水泵Feed water pump of boiler 泵Pump 11 ）锅炉燃油泵Fuel oil pump of boiler1）主机滑油泵Main engine lubricating oil pump12）分油机供给泵Fuel oil supply pump of purifier2）主机缸套水泵Main engine cylinder cooling water pump13）制淡海水泵Sea water pump of fresh water generator3）主机缸套水预热泵Main engine cylinder cooling water preheating pump14）压载泵Ballast pump4）主机海水泵Main engine sea water pump 15 ）舱底消防泵Bilge and fire pump17）油渣泵Sludge oil pump 2 、柴油澄清舱Diesel oil setting tank18）柴油输送泵Diesel oil transport pump 3 、燃油日用柜Fuel oil daily tank19)燃油油输送泵 Fuel oil transport pump 4 、燃油澄清舱 Fuel oil setting tank 20) 汽缸油输送泵 Cylinder oil transport pump 5 、滑油澄清舱 Lubricating oil setting tankFresh water transport pump 6 、滑油储藏舱 Lubricating oil store tank Hot watercirculating pump 7 、滑油循环舱 Lubricating oil circulating tank Drinking waterpump 8 、燃油溢油舱 Fuel oil overflow tankBilge, fire and G.S pump 9、燃油油渣舱 Fuel oil sludge tank喷淋泵 Sprinkling pump 10 燃油深舱 Fuel oil deep tank停泊海水泵 Harbor sea water pump 11 滑油污油舱 Lubricating dirty oil tank 12 滑油溢油舱Lubricating oil overflow tank二、各种舱（箱）柜All kinds of tank 13 滑油油渣打舱 Lubricating oil sludge tank1、柴油日用柜 Diesel oil daily tank 14 主机淡水膨胀水箱 M.E fresh water expansion tank15 付机淡水膨胀水箱A.E fresh water expansion tank16、淡水压力柜 Fresh water pressure tank 1、滑油系统 Lubricating oil piping system17、热水压力柜 Hot water pressure tank 2 、燃油系统 Fuel oil piping system18、饮水压力柜 Drinking water pressure tank3、海水系统 Sea water piping system19、淡水舱 Fresh water tank 4、缸套水系统 Cylinder cooling water piping system20、饮水舱 Drinking water tank 5 、启动空气系统 Start air piping system21、锅炉水舱 Boiler water tank 6 、控制空气系统 Control air piping system22、分油机工作水箱Purify operating water tank 7 、排气系统 Exhaust piping system23、汽缸油日用柜 Cylinder oil daily tank 8 、日用供水系统 Daily water piping system24、尾管滑油重力柜Gravity tank of tube oil 9 、蒸汽系统 Steam piping system25、排气水封箱 Exhaust seal water tank 10 、锅炉给水和凝水系统 Feed water and condensate ofboiler piping system26、蒸馏水水舱 Distilling water tank 11 、燃油净油系统 Fuel oil purified piping system27、污水井 Bilge well 12 、燃油输送系统 Fuel oil transport piping system三、各种管系系统 All kinds of pipes舵销 Rudder pintle 13 、滑油净油系统 Lubricating oil purified piping system 舵杆衬套 rudder stockliner 14 、滑油输送系统 Lubricating oil transport piping system 舵杆轴套 Sleeve for rudder stock15 、舱底压载系统 Ballast and bilge water piping system 舵销承衬套 Bush for rudder pintle 四、仪表类 Instructions 舵销轴套 Sleeve for rudder pintle 1 、压力表 Pressure gauge 上舵承底座 Ruddercarrier seat 2、真空表 Vacuum gauge 舵销承座 Pintle bearing 3 、温度计 Thermometer 舵杆承座Rudder stock bearing 4 、吨位表 DWT gauge 挡圈 Retaining ring 5 、遥测表 Distant survey gauge舵柄 Tiller 6 、液全器 Level switch7) 舵角 The angle of rudder5、空压机 Air compressor1）主空压机 Emergency air compressor2）应急空压机7、传感器 Sensor 12、机控室 Engine control room 五、其它 Others 13 、台虎钳 Vise （=vice ）淡水输送泵 热水循环泵 饮水日用泵 舱底消防总用泵 21) 22) 23)1、风机Fan 14、表铜截止阀Bronze close valve2、防海生物装置Anti-foul STM plant 15 、表铜截止止回阀Bronze check valve3、泡沫柜Air foam tank 16 、铸铁截止阀Cast iron stop valve4、中间轴Middle shaft 17 、铸铁截止止回阀Cast iron check and stop valve5、尾轴Propeller shaft 18 、调节阀Adjustable valve6、螺旋桨Propeller 19 、溢流阀、安全阀Relief valve7、中间轴承Line shaft bearing 20 、减压阀Reducing valve8、泡沫灭火机Foam fire extinguisher 六、材料Material9、饮水消毒装置Sterilizer plant 1 、管子Pipe10、主配电板Main switch board 2 、无缝钢管Seamless steel pipe （tube）11、机舱集控台Engine room control console 3 、紫铜管Purple copper pipe4、铁法兰Iron flange 18 、支架（马脚）Clamp5、铜法兰Copper flange 19 、油漆Paint6、盲板法兰Blind-flange 20 、备件Spare parts7、螺丝（螺栓）Bolt8、双头螺丝Stud 七、生产工具Produce tool9、螺帽（螺母）Nut 1 、图纸Drawing10、不锈钢螺丝Stainless steel bolt 2、活络钣Adjustable spanner11、垫片（床）Gasket 3、令司板（梅花钣）Ring spanner12、橡皮床Gum gasket 4、开口钣Open - ender spanner13、纸箔床Paper copper gasket 5、管子钳Pipe wrench14、紫铜床Purple copper gasket 6、凿子Chisel15、石墨床Black lead gasket 7 、锒头Hammer16、青铅床Black lead gasket 8 、锉刀File17、佛纳Feeler gauge 9、螺丝刀Screwdriver10、油漆滚筒Paint roller 4 、首先请检查安装说明和电气绝缘11 、油漆刷子Paint brush Please check the condition of installation and insulationfirst12、钢锯Hacksaw 5、我们准备将油水分离器动转13、套筒扳手Socket spanner Now we will run the oily-water separator14、手电筒Torch 6 、请检查动转情况15、钻头driller Please check the running condition八、英语会话7、接着我们一个一个地做报警/安全保护装置的功能试验I 、早上好good morning Now we will do the function test about alarm and safetydevice2、今天我们准备交验油水分离器8、设备交接基本结束Today we will test the oily-water separator. Now the test is over3、请跟我来9、请部有何修改意见？Please fellow me. Do you have any question ?10、非常感谢17、这里增加一只落水斗Thanks Add a drain plug hereII 、再见18、请用空气压缩空气吹干Good bye Please dry it by the compressed air12、请把这对法兰撬紧松开19 、我将回车间支拿肥皂水Please tighten/release the flange I will com to my workshop to take some soap water13、这路管子是从发电机单元来的20、这个系统非常重要的，一定要认真检查The piping is from to the G/E unit This system is very important ,please check it carefully14、这对法兰/接头在漏21 、请交验收整改意见This flange /connection is linking Please check your remarks15、这路系统的试验压力是7 公斤22、天太热了，请休息一会The test pressure of the piping system is 7 bar It ' s too hot ,please take a rest16、这里请加强please make a clamp here 23、我负责这项工作I am in charge of this job电气部分ELECTRIC PART 一、常用词汇Words and expression 模拟Analog(ue)2182 千赫值班接收机2182KHz watch receiver 锚灯Anchor light A 异常Abnormal 风速风向仪Anemorumbometer 应答Acknowledge 阳极Anode 有功功率Active power 天线Antenna 执行器Actuator 天线馈线连接器Antenna feeder connector 调整Adjust 天线引入绝缘端子Antenna leading - in insulator空气断路器Air circuit breaker 天线共用器Antenna multicoupler 报警系统Alarm system 天线调谐器Antenna tuner 交流电Alternating current 电焊机Arc welder 电流表ammeter 声音的Audible放大器Amplifier 自动海图标绘仪Auto chart plotter 自动舵Auto pilot 自动的Automatic 自动雷达标绘仪Automatic radar plotting aid 球鼻首警告灯Bulbous bow warning light 自动电话Automatic telephone 汇流排Bus(-)bar 电压自动调节器Automatic voltage regulator 汇流排Bus - tie - in自动化系统Automation system 蜂鸣器Buzzer 压载控制台Ballast control console C 、电缆Cable 镇流器Ballast 电缆填料函Cable gland 底座Base 敷设电缆Cable laying 电池Battery 电缆管Cable pipe (conduit) 铃Bell 电缆扎带Cable strap 弯曲Bend 电缆托架Cable tray 床头灯Berth light 校准器Calibrator 失电Black out 电容capacitor 刹车Brake 阴板Cathode 电刷Brush 警告牌Caution plate 顶灯Ceiling light 通讯Communication 中央处理器Central processing unit 计算机Computer 通道Channel 接头Connector 充电器Charger 恒电流Constant current充放电板Charging&discharging board 消耗Consumption 海图灯Chart table light 触头Contact 检查Check 接触器Contactor 芯片Chip 控制箱Control box 清洁Clean 控制箱Controller 雨雪清除器Clear view screen 芯线Core 二氧化碳释放报警CO2 release alarm 角灯Corner light 同轴电缆Coaxial cable 计算器Counter 线圈Coil 电流Current 冷库呼叫Cold store calling D 、损坏Damage 危险气体报警箱Dangerous gas detecting &alarm box 双极单刀开关Double pole single way switch 白昼信号灯Daylight signal light 双极双刀开关Double pole two way switch 去耦Decoupling set 天线收发转换开关Duplexer 台灯Desk light 值班水手呼叫Duty sailor calling 控测器Detector 接地Earth 拨号Dial 接地排Earth bar 数字选择呼叫收信机Digital select -call receiver 测深仪Echo sounder 调光器dimmer 电工试验板Electric test panel 直流电Direct current 电机员Electrical engineer 直接起动Direct - on - line starting 电极Electrode 磁盘Disk 应急照明分电箱Emergence lighting distribution box 显示Display 应急示位标Emergence position indicating radiobeacon 遇险信息控制器Distress message controller 应急停Emergence stop 多普勒记程仪Doppler speed log 应急配电板Emergency switch board 馈电品Feeder panel 机舱报警Engine alarm 滤波器Filter 集控台Engine control console 火警复显器Fire alarm repeater 机舱监测报警Engine room monitoring&alarm system 防火风闸控制单元Fire damper control unit 轮机员呼叫Engineer calling panel 火警检测箱Fire detecting box 轮机员安全Engineer safety system 火焰探头Flame detector 增强群呼叫收讯机Enhance group call receiver 闪光灯Flash light 交换机Exchanger 浮充电Float charge 防爆灯Explosion proof light 强光灯Flood light 延伸报警板Extension alarm panel 流程图Flow chart 故障Failure 流量开关Flow switch 故障Fault 荧光灯Fluorescent light 反馈Feed back 雾笛Fog horn频率Frequency熔丝Fuse 感温探头Heat detector填料Gasket 底座Holder 通用报警General alarm 电笛、喇叭Horn 发电机Generator 病房呼叫Hospital calling 发电机屏Generator panel 照明Illumination （铜）锣、钟Gong 白炽灯Incandescent light 全球卫星定位导航GPS navigator 指示器Indicator 组合灯板Group alarm light pillar 卫星B 站INMARSAT B station 组合起动屏Group starter panel 卫星C 站INMARSAT C station 电罗经Gyro compass 输入输出Input /output 卤素灯Halogen light 安装Install 听筒Handset 仪表Instrument 硬件Hardware 绝缘胶带Insulating tape 航向Heading 绝缘Insulation 接口、界面Interface 限位开关Limit switch 连锁Interlock 连接Link 中断Interrupt 负载Load 逆变器Inverter 劳莱收信机Loran receiver 接线盒Junction box 磁罗经Magnetic compass 键盘Keyboard 主机电子调速器Main engine electronic governor 灯泡Lamp 主机功率、纽力仪Main enginepower& torque unit 液位开关Level switch 主机遥控系统Main engine remote control system 液位传感器Level transmitter 主机转速表Main engine revolution meter 灯Light 主机安全系统Main engine safety system 灯柱Light column 主机增压器转速表Main engine turbo-charger speed meter 照明分电箱Light distribution box 主配电板Main switchboard 避雷针Lighting arrester 手动手册Manual 标记Mark 移动Move 桅杆Mast light 万用表Multimeter 母子钟Master& slave clock 铭牌Name plate 匹配箱Matching box 窄频直接打印机Narrow-band direct printer 测量Measure 航行灯Navigation light 兆欧表Megohmmeter 导航系统Navigation system 仪表Meter 航行监控台Navigation watch console 话筒Microphone 航行警告收信机NAVTEX receiver 镜向灯Mirror light 负极Negative 监视器Monitor 网络Network 莫斯键Morse key 标称值Nominal value 电动机Motor 常闭Normally closed 塑壳断路器Moulded case circuitbreaker 常开Normally open 鼠标Mouse 失控灯Not under-command light 欧姆表Ohm gauge 正极Positive 欧姆收信机Omega receiver 功率、电源Power 车钟记录仪Order printer 电力分电箱Power distribution box示波器Oscilloscope 功率因素Power factor 过电流Over current 优先卸载Preferential trip 过载Overload 压力开关Pressure switch 巴拿马动河操舵灯Panama canal steering light 压力传感器Pressure switch 并联、并车Parallel 一次系统Primary system 相Phase 打印机Printer 光敏电阻Photo resister 程序Program 测速传感器Pick up 螺旋桨警告灯Propeller warning light 插头Plug 广播Public addressor 左舷灯Port light 脉冲Pulse 便携电话Portable telephone 按钮Push button 雷达Radar 电阻Resistance 雷达应答器Radar transponder 逆功率Reverse power 收音机Radio 旋转灯Rotating light 无线电测向仪Radio direction finder 舵角指示器Rudder angle indicator 随机存取存储器Radio system 运转灯Running lamp 额定Random access memory 屏幕、屏蔽Screen 无功电流Rated power 螺丝刀Screwdriver 插座Receptacle 搜索灯Search light 录音机、记录仪Recorder 二次系统Secondary system 整流器Rectifier 串联Series 继电器Relay 屏蔽Shield 复位Reset 船名灯Ship name light 岸电箱Shore connection box 短路Short circuit 展示、给看Show 电磁阀Solenoid valve分励脱扣Shunt trip 消音Sound off 停车Shut down 声力电话Sound power telephone 签字Sign 空间加热器Space heater 信号集合箱Signal acquisition unit 扳手Spanner 信号灯Signal light 喇叭Speaker 单边带收发机Single side band transceiver 分配器Distributor 电笛Siren 右舷灯Starboard light 慢车Slow down 起动Start 烟气探测报警箱Smoke detecting &alarm box 起动带Start 感烟探头Smoke detector 尾灯Stern light 插座Socket 停止Stop 软件Software 苏伊士运河尾灯Suez canal stern light 电烙铁Soldering iron 支撑物supporter 开关Switch 验电笔Test pen 打开Switch on 试验程序Test procedure 关闭Switch off 热敏电阻Thermistor 同步屏Synchronizing panel 热电偶Thermocouple同步表 Synchronoscope 温度计 Thermometer 转速表 Tachometer 恒温计 Thermostat 录音机 Tape recorder 触摸屏 Touch panel 车钟 Telegraph 轨迹球 Trackball 电视 Television 收发机 Transceiver温度开关 Temperature switch 传感器 Transmitter温度传感器 Temperature transmitter 变压器 Transformer电压 Voltage 检验员 q-quality inspector 电压表 Voltmeter 电工 e-electrician壁灯 Wall light 1 、检验电缆敷设瓦特 Watt Inspection cable laying波道 Waveguide 你能带我去看机舱电缆敷设气象传真收信机 Weather fax receiver Q: could you show me cable laying of engine room? 驾控台 Wheel speed &directionindicator 好，走吧。
船舶与海洋工程专业专业英语词汇
船舶与海洋工程专业专业英语词汇1、A类a faired set of lines 经过光顺的一组型线 abaft 朝向船尾absence 不存在accommodation 居住(舱室)acquisition cost 购置（获取）成本activate 作动adopt 采用aegis 保护，庇护aerostatic 空气静力学的after perpendicular (a. p. ）艉柱ahead and astern 正车和倒车 air cushion vehicle 气垫船aircraft carrier 航空母舰airfoil 气翼，翼剖面，机面，方向舵airfoil 气翼，机翼alignment chock 组装校准用垫楔(或填料)allowance 公差，余(裕)量，加工裕量，补贴 American Bureau of Shipping (美国)船级社amidships 舯amidships 在舯部amphibious 两栖的angle of attack 攻角angle plate 角钢 anticipated loads encountered at sea在海上遭遇到的预期载荷antiroll fins 减摇鳍 appendage 附体appendage 附件，附体 appendage 附体artisan 技工 assembly line 装配(流水)线athwart ships 朝 (船)横向 at-sea replenishment 海上补给axiomatic 理所当然的，公理化的2、B类back up member 焊接垫板 backing structure 垫衬结构Bar 型材，材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船 base line 基线base, base line 基线basic design 基本设计batten 压条，板条 be in short supply 供应短缺、俏销beam 船身最大宽，横梁beam 船宽，梁bench work 钳工 bevel 折角bid 投标 bidder 投标人(者)bilge 舭，舱底bilge 舭bilge keel 舭龙骨 bilge radius 舭半径bills of material 材料(细目)单 blast 喷丸(除锈)block coefficient 方形系数block coefficient 方形系数Board of Trade (英国)贸易厅 body plan 横剖面图body section 横剖图 Bonjean curve 邦戎曲线boom 吊杆 boundary layer 边界层bow line 前体纵剖线 bow thruster 艏侧推器bow wave 艏波boyant 浮力的bracket 轴支架，支架breadth extreme 最大宽，计算宽breadth moulded 型宽breakbulk 件杂货buckle 屈曲budget 预算，作预算buffer area 缓冲区building basin 船台 bulb plate 球头扁钢bulbous bow 球状船艏bulbous bow 球鼻艏bulk oil carrier 散装油轮bulk carrier 散装货船bulk carrier 散装货船 buoyancy 浮力buoyancy 浮力Bureau Veritas (法国)船级社burning machine 烧割机 butt weld 对缝焊接buttock 后体纵剖线by convention 按照惯例，按约定3、C类camber 梁拱capacity plan 舱容图capsize 倾覆capsizing moment 倾覆力矩captured-air-bubble vehicle 束缚气泡减阻船cargo capacity 载货量，货舱容量，舱容cargo cubic 货舱舱容，载货容积cargo handling 货物装卸 cargo owner 货主carpenter 木匠 carriage of grain cargoes 谷类货物输运机cascading of waves upon…海浪跌落于… casualty 事故，死伤，灾难catamaran 双体船categorize 分类centroid 形心，重心，质心，矩心 chine 舭，舷，脊chock 木楔 circumscribe 外接，外切circumsection 外切Coast Guard cuttle(美国）海岸警备队快艇commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船compartment 舱室 concave 凹，凹的，拱conceive 设想，想象concept design 概念设计configuration 构形，配置configuration安排，构型，配置conspicuous 显着的，值得注意的containerized 集装箱化 contract design 合同设计contract design 合同设计 contracted scale 缩尺core box 型芯 corrosion 锈蚀，腐蚀couple 力矩，力偶crest (of wave) 波峰crew quarters 船员居住舱 Critical Path Method (CPM) 关键路径法cross section 横剖面 cross sectional area 横剖面面积cross-channel automobile ferries 横越海峡客车渡轮crucial element 重要因素cruiser stern 巡洋舰尾cruissing range 航程curvature 曲率curves of form 各船型曲线cushion of air 气垫4、D类damage stability 破损稳性 damp out 阻息，逐渐降低dead load 恒(静)载荷 deadweight 总载重量(吨)deballast 卸除压载(压舱)deck line at side 甲板边线deck camber 甲板梁拱deck wetness 甲板淹湿 deckhouse 舱面室，甲板室declivity 坡度，斜度 deep V hull 深V型船体deformation 变形 delivery 交船Department of Trade (英国)贸易部 deposit metallic plating 镀上金属镀层depth moulded 型深depth 船深depth 船深 design spiral 螺旋式设计destroyer 驱逐舰detail design 详细设计deviation 偏离，偏差 devious 曲折的diagram 图，原理图，设计图，流程图 dimension 尺度，元，维displacement 排水量distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠draft 吃水draftsman 绘图员 drag 阻力Drainage 排(泄)水draught(=draft) 吃水，草图，设计图，牵引力drawing office 绘图室 dredge 挖泥船drift 飘移，偏航drilling rig 钻架 dry dock 干船坞5、E类eddy 旋涡electrohydraulic 电动液压的electroplater 电镀工 elevations 高度，高程，船型线图的侧面图、立视图，纵剖线图 enclosed fabrication shop 封闭式装配车间end on 端对准 endurance 续航力endurance 续航性 entrance 进流段 erection (船体)组装erection 装配，安装 expedient 权宜之计extrapolate 外插f. p. = forward perpendicular 艏柱fair 光顺 fair 光顺fastening 坚固件,紧固法fatigue 疲劳 feasibility study 可行性研究 fender 护舷ferry 渡轮，渡口，渡运航线ferry 轮渡(载运) fillet weld connection 贴角焊连接fine fast ship 纤细(细长)高速船 fine form 瘦长(细长)船形Flank 侧面, 侧翼, 侧攻flanking rudders 侧翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队 flexural 挠曲的float 浮动时间 floating drydock 浮船坞 flood 进水，泛滥floodable length curve 可浸长度曲线 flow pattern 流型，流线谱flow of materials 物流 flush 平贴，磨光forging 锻件，锻造 form coefficient 船形系数forming operation 成型加工 forward/after perpendicular 艏/艉柱forward/after shoulder 前/后肩 foundry casting 翻砂铸造 foundryman 铸造翻砂工 frame 船肋骨，框架，桁架frame 框架 freeboard 干舷freeboard 干舷freeboard 干舷freeboard deck 干舷甲板 freight rate 运费率fresh water 淡水 frictional resistance 摩擦阻力Froude number 傅汝德数full form 丰满船形full form ship 丰满船型 fullness 丰满度funnel 烟囱galley (船舰，飞机的)厨房Gantt Chart 施工进度表 general arrangement 总布置general arrangement 总布置 Germanischer Lloyd (德国)劳埃德船级社 girder 桁，梁gradient 梯度grating 格栅 Green Book (船级社)绿皮书 (登录快速远洋船) ground level building site 平地建造场 group technology 成组建造技术grouting 填缝、灌浆 guided-missile cruiser 导弹巡洋舰habitability 适居性half breadth plan 半宽图handling equipment 装卸设备 hard chine 尖舭headroom 净空高度heave 垂荡 heel 横倾heel 柱脚，踵材，底基，倾斜 hog 中拱hogging 中拱 hold 船舱hole 水流深凹处homogeneous cylinder 均质柱状体hopper barge (自动)倾卸驳 hostile sea 凶险的波浪hostile sea 汹涌波浪 hull block 船体垫块，船体支座 hull form 船形hull form 船形 HVAC (=heating, ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构 hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船icebreaker 破冰船identified as Essential Changes 标记作“必备变更项” immerse 浸入 immerse 浸没impact load 冲击载荷imperial unit 英制单位impression 模槽，型腔，印痕，印象in strake 内列板 in way of…在…处inboard profile 纵剖面图 In-depth analysis 深入研究initial stability at small angle of inclination 小倾角初稳性insulation 绝缘，隔离Intact stability 完整稳性Intergovernmental Maritime Consultative Organization 国际海事质询组织Intergovernmental Maritime Consultative Organization (IMCO) 国际政府间海事质询组织International Association of Classification Society (IACS) 国际船级社联合会International Convention for the Safety of Life at Sea (ICSOLAS) 海上生命安全性国际公约International Towing Tank Conference 国际船模试验水池会议intersection 交点，交叉，横断(切)intervening deck 居中甲板introduces a bill 提出一项议案 issue periodically 定期发布(公布)iterative process 选代过程jack 千斤顶 janitorial 勤杂工，房屋照管者joggle 折曲，榫接，弯合 joiner 安装工joiner 细木工(匠)joinery 细木工keel laying 开始船舶建造(原意为“铺设龙骨架”) Kips (= kilo-pounds) 千磅laborer 力工Land borne 陆基的，装在陆地的 landing craft 登陆艇large tank and sphere 大型油罐和球罐launch 发射，下水launching equipment（向水中）投放设备launching way (船舶)下水滑道 LCC(Large Crude Carrier）大型原油轮（载重10~20万吨）lead time 设计至投产、定货至交货的时间 legislation 立法length between perpendicular 两柱间长leveler 调平器，矫平机，矫直机life saving appliance 救生设备 life-cycle cost 生命周期成本lift fan 升力风扇lift offsets 量取型值Light ship weight 空船重量 lighter 港驳船likely 多半，可能line 型线liner 定期航班船liner trade 定期班轮营运业lines plan 型线图liquefied gas carrier 液化气运输船list 倾斜, 表living and utility spaces 居住与公用舱室Lloyd’s Machinery Certificate (LMC) 劳埃德(船舶)机械证书Lloyd’s Register of Shipping (英国)劳埃德船级社Lloyds Rules 劳埃德(船级社)规范LNG containment 液化天然气容器Load Line Regulation 载重线公约、规范load waterline 载重水线load waterplane 载重水线面loft floor 放样台full scale 全尺度loftman 放样工loftman 放样工longitudinal 纵向的longitudinal 纵向的，纵梁longitudinal prismatic coefficient 纵向棱形系数machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main shafting 主轴系major ship 大型船舶maneuverability 操纵性maritime 海事的，海运的，靠海的，沿海的mark out 划线，划记号marshal 调度mast 桅杆maximum beam amidships 舯最大宽member 部件merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate bath 金属板电镀槽metal worker 金属工metric unit 公制单位midbody （船）中体middle line plane 中线面midship area coefficient 舯横剖面系数midship section 舯横剖面midship section coefficient 舯横剖面系数mill shape 轧钢厂型材module assembly 模块式组装mold loft floor (型线)放样间地板molded lines 型线molder 造型工mould loft 放样间moulded line 型线multihull vessel 多体船Multi-ship program 多种船型建造规划nautical mile 海里naval architect 造船师naval architecture 造船工程naval ship 军船naval architecture 造船学nearuniversal gear 准万向齿轮network flow 网络流程neutral equilibrium 中性平衡normal 法向，法向的，正交的normal force 法向力normal operating condition 常规(正常)运作工况notch 开槽，开凹口Off the shelf 成品的，畅销的，流行的off-center loading 偏移中心的装载offsets 型值offshore drilling 离岸钻井oil-rig 钻油架operational requirement 军事行动需求，运作要求orient 取向，定方位，调整orthogonal 正交的，矩形的out strake 外列板outboard profile 侧视图outfit 舾装outfitter 舾装工outfitting 舾装overall stability 总体稳性overhang 外悬overstocking 存货过剩owner’s staff 船东的雇(职)员paint priming 涂底漆Panama Canal 巴拿马运河panel line system 板材生产线系统parallel middle body 平行中体patternmaker 木模工payload 有效载荷permanent body 永久性组织机构perpendicular（船艏、艉）柱，垂直的，正交的pillar 支柱pin 钉，销pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge (海底) 铺管驳船piping 管路pitch 纵摇plan views 设计图planing hull 滑行船体pleasure ship 游乐用船Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船Polaris (submarine) 北极星级(潜艇)port 左舷portable gate 移动式(可移动)闸门positive righting arm 扶正力臂power and lighting system 动力与照明系统preliminary design 初步设计preliminary/concept design 初步/概念设计pressure vessel 压力容器principal dimensions 主尺度prism 棱柱体prismatic coefficient 棱形系数procurement 采购，获得Program Evaluation and Review Technique 规划评估与复核法quartering sea 尾斜浪, 从船斜后方来的浪quay(横)码头，停泊所racking 倾斜，变形，船体扭转变形radiography X射线照相术，X射线探伤rake 倾角,倾斜ram pressure 速压头，冲压，全压力rectangle 矩形reenlistment 重征服役Registo Italiano Navale (意大利)船级社remedial action 补救措施reserve buoyancy 储备浮力reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力resultant 合力retract 收进revolving crane 旋转式(鹤)吊，转臂吊(车)Reynolds number 雷诺数rigger 索具装配工rigid side walls 刚性侧壁rise of floor 底升risk 保险对象，保险金额rivering warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇rolled angle butt (轧制)角钢焊接头roll-on/roll-off(RO-RO) 滚装rough sea 汹涌的波浪round of beam 梁拱rounded gunwale 修园的舷边rubber tile 橡皮瓦rudder post 舵柱rudder 舵rudder rate 舵率rudder stock 舵杆run 去流段Sag 中垂sagging 中垂scale 缩尺，尺度，尺scale model 缩尺船模scantling 材积sea keeping performance 耐波性能seasickness 晕船seaworthiness 适航性section 剖面，横剖面sections (铁、钢)型材，轧材self-induced 自身诱导的semi finished item 半精加工件semisubmersible drilling rig 半潜式钻井架set course 设定的航线set course 设定航线shaft bossing 轴包套shaft bracket 轴支架shear 剪切，剪力sheer aft 艉舷弧sheer forward 艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 纵剖线sheer profile 纵剖图sheer(甲板)舷弧sheet metal work 钣金工，冷作工shell plating 船壳板shell 船壳板ship fitter 船舶装配工ship fitter 船体安装工ship fitter 舰船装配工ship form 船型ship Hydrodynamics 水动力学ship owner 船东shipping line 船运航线shipway (造)船台shipwright 船体装配工，造船工人shipyard 船厂shipyard 船厂shipyard schedule chart 船厂施工进度图shoring 支撑，支柱shoulder 船肩sideways 朝侧向six degrees of freedom 六自由度sizable 相当大的skirt（气垫船）围裙slamming 砰击，拍击slice 一部分，薄片sloping shipway 有坡度船台，滑道soft chine 圆舭spare part 备件specially prepared form 专门(特殊)加工的模板spectrum 谱speed-to-length ratio 速长比stability 稳性stable equilibrium 稳定平衡standard 规章starboard 右舷static equilibrium 静平衡statically determinant 静定的statistical 统计学(上)的steel marking 钢板划线steering gear 操纵装置steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 艉stern frame 艉构架，艉框架stern wave 艉波stiffen 加劲，加强stiffener 肋骨strain 应变strake 船体列板stringent safety regulations 严格的安全规章structural alignment 结构校准，组合，组装strut 支柱，支撑构形subassembly (局部)分部装配subdivision 分舱sublet 转包，分包，转租submersible 潜器suction cup 吸盘Suez Canal Tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线super cavitating propeller超空泡螺旋桨superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supertanker 超级油轮supervision of the Society’s surveyor 船级社验船师的监造surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过survivability 生存力SWATCH(Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡switchboard 控制台，开关板tabular freeboard 列成表格的干舷值tacker 定位搭焊工talking paper 讨论文件tangential viscous force 切向粘性力tanker 油轮tanker 油轮tantamount 等值的，相当的taper 弄细，变尖tee T形构件，三通管template 样板tensile stress 拉(张)应力The Register of Shipping of the People’s Republic of China 中国船舶检验局The Titanic 泰克尼克号(巨型邮轮)there is more shape to the shell 船壳板的形状较复杂titanic 巨大的to be craft oriented 与行业有关的，适应于行业性的to run the waterlines 绘制水线toed towards amidships 趾部朝向船舯ton gross=gross ton 长吨=1. 016公吨tonnage 吨位torque 扭矩torsio 扭转的trade 工种, 贸易trailer type transporter 拖车式载运车transfer sideways 横向移动transom (stern) 方尾transverse 横向的transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体船trough 波谷tugboat 拖船tumble home(船侧)内倾Type A ship A类船U form U型U. S. Coast Guard 美国海岸警卫队ULCC(Ultra Large Crude Carrier）超级大型原油轮（载重量>40万吨）ultrasonic 超声波的\underwriter (海运)保险商undock 使船出坞upright position 正浮位置V shaped V型的ventilation and air conditioning diagram 通风与空调敷设设计图vertical prismatic coefficient 垂向棱形系数vertical prismatic coefficient 垂向棱形系数vicinity 邻近，附近villain 坏人，罪魁viscosity 粘性VLCC(Very Large Crude Carrier）巨型（原）油轮（载重量>20万吨）V-sectionV型剖面wash 下洗 ,艉流water line 水线waterborne 浮于水上的，水基的waterplane 水线面waterplane area coefficient 水线面积系数watertight integrity 水密完整性wave pattern 波型wavemaking resistance 兴波阻力weather deck 露天甲板weld inspection 焊缝检测welder 焊工weldment 焊件，焊接装配wetted surface 湿面积wing shaft 侧轴yacht 快艇yard issue 船厂开工任务发布书yaw 艏摇yaw 艏摇，摇艏。
船舶专业英语词汇
船舶专业英语词汇1, steering ['sti?ri?]n. 操纵；指导；掌舵v. 驾驶；掌舵（steer的ing形式）2, gear [ɡi?]n. 齿轮；装置，工具；传动装置vi. 适合；搭上齿轮；开始工作vt. 开动；搭上齿轮；使……适合；使……准备好adj. 好极了3, refrigeration [ri,frid??'rei??n, ri:-]n. 制冷；冷藏；[热] 冷却4, provision [pr?u'vi??n]n. 规定；条款；准备；[经] 供应品vt. 供给…食物及必需品5, store [st?:]n. 商店；储备，贮藏；仓库vt. 贮藏，储存6, tally ['t?li]n. 计数器；标签；记账vt. 使符合；计算；记录vi. 一致；记分7, changing ['t?eind?i?]v. 改变（change的ing形式）；交换；兑换n. 改变；转换；替换adj. 变化的；发展的8, gym [d?im]n. 健身房；体育；体育馆9, electric [i'lektrik]adj. 电的；电动的；发电的；导电的；令人震惊的n. 电；电气车辆；带电体10, channel ['t??n?l]vt. 引导，开导；形成河道n. 通道；频道；海峡11, pipe joint管接；导管接头12, pipe [paip]n. 管；烟斗；笛vi. 吹笛；尖叫vt. 用管道输送；尖声唱；用管乐器演奏13, laundry ['l?:ndri, 'lɑ:n-]n. 洗衣店，洗衣房；要洗的衣服；洗熨；洗好的衣服14, sanitary ['s?nit?ri]adj. 卫生的，清洁的n. 公共厕所15, case [keis]n. 情况；实例；箱vt. 包围；把…装于容器中16, etcadv. 等等，及其他17, accommodation [?,k?m?'dei??n]n. 住处，膳宿；调节；和解；预订铺位18, forepeak ['f?:pi:k]n. 船首舱19, airconabbr. 空调（Air conditioning）20, galley ['ɡ?li]n. [船] 船上的厨房；单层甲板的大帆船；活版盘，长条校样21, mess [mes]n. 混乱；食堂，伙食团；困境；脏乱的东西vt. 弄乱，弄脏；毁坏；使就餐vi. 把事情弄糟；制造脏乱；玩弄22, toilet ['t?ilit]n. 厕所，盥洗室；梳妆，打扮vi. 梳妆，打扮vt. 给…梳妆打扮23, stair [stε?]n. 楼梯，阶梯；梯级24, crew [kru:]n. 队，组；全体人员，全体船员vi. 一起工作vt. 使当船员25, conference room会议室，会议厅26, conferencen. 会议；协商；讨论；[篮]联盟27, captain ['k?ptin]n. 队长，首领；船长；上尉；海军上校vt. 指挥；率领28, chief engineer[劳经] 总工程师；轮机长；主任工程师；总技师29, pilot ['pail?t]n. 飞行员；领航员adj. 试点的v. 驾驶；领航；试用30, charging ['t?ɑ:d?i?]n. 炉料；装料v. 使承担（任务等）；装载；命令（charge的现在分词）31, discharge [dis't?ɑ:d?, 'dist?ɑ:d?, dis't?-]vt. 解雇；卸下；放出；免除vi. 排放；卸货；流出n. 排放；卸货；解雇32, radar ['reid?]n. [雷达] 雷达，无线电探测器33, mast [mɑ:st, m?st]n.桅杆；柱；橡树果实vt. 在…上装桅杆34, communication [k?,mju:ni'kei??n]n. 通讯，[通信] 通信；交流35, signal ['siɡn?l]n. 信号；暗号；导火线vt. 标志；用信号通知adj. 显著的；作为信号的vi. 发信号36, recorded [ri'k?:did]adj. 记录的v. 记录；录音（record的过去分词）37, general arrangement总布置38, reliale39, assessed [?'sest]v. 对…进行评估（assess过去时形式）40, maintainedadj. 被保持的v. 维护，维修；维持（maintain的过去分词）41, yacht [j?t]vi. 乘游艇，驾游艇n. 游艇，快艇；轻舟42, overhaul [,?uv?'h?:l, '?uv?h?:l]vt. 分解检查，大修；追上并超过n. 彻底检修，详细检查43, maintenance ['meint?n?ns]n. 维护，维修；保持；生活费用44, extremesn. 狂热分子，极端条件45, encounter [in'kaunt?]vt. 遭遇，邂逅；遇到n. 遭遇，偶然碰见vi. 遭遇；偶然相遇46, encountered [in'kaunt?d]v. 遇到；曾遭遇（encounter的过去式）47, toll [t?ul, t?l]损失。
船舶工程专业英语词汇
船舶工程专业英语词汇一、各种舱(箱)柜All kinds of tank1、柴油日用柜Diesel oil daily tank2、柴油澄清舱Diesel oil setting tank3、燃油日用柜Fuel oil daily tank4、燃油澄清舱Fuel oil setting tank5、滑油澄清舱Lubricating oil setting tank6、滑油储藏舱Lubricating oil store tank7、滑油循环舱Lubricating oil circulating tank8、燃油溢油舱Fuel oil overflow tank9、燃油油渣舱Fuel oil sludge tank10燃油深舱Fuel oil deep tank11滑油污油舱Lubricating dirty oil tank12滑油溢油舱Lubricating oil overflow tank13滑油油渣打舱Lubricating oil sludge tank14主机淡水膨胀水箱M.E fresh water expansion tank15付机淡水膨胀水箱A.E fresh water expansion tank16、淡水压力柜Fresh water pressure tank17、热水压力柜Hot water pressure tank18、饮水压力柜Drinking water pressure tank19、淡水舱Fresh water tank20、饮水舱Drinking water tank21、锅炉水舱Boiler water tank22、分油机工作水箱Purify operating water tank23、汽缸油日用柜Cylinder oil daily tank24、尾管滑油重力柜Gravity tank of tube oil25、排气水封箱Exhaust seal water tank26、蒸馏水水舱Distilling water tank27、污水井Bilge well1、滑油系统Lubricating oil piping system2、燃油系统Fuel oil piping system3、海水系统Sea water piping system4、缸套水系统Cylinder cooling water piping system5、启动空气系统Start air piping system6、控制空气系统Control air piping system7、排气系统Exhaust piping system8、日用供水系统Daily water piping system9、蒸汽系统Steam piping system10 、锅炉给水和凝水系统Feed water and condensate of boiler piping system11、燃油净油系统Fuel oil purified piping system12、燃油输送系统Fuel oil transport piping system机舱部分ENGINE ROOM PART二、机舱设备Machines and equipment in engine room1、主机Main engine1)主机油底壳The sump tank of M.E.2)主机飞轮Fly wheel of M.E3)活塞Piston2、发电机Generator engine1)应急发电机Emergency generator engine2)辅机Auxiliary3、锅炉Boiler1)组合锅炉The composite boiler2)锅炉安全阀The safety valve of boiler323)燃烧器Oil burner unit4)水位表Water level gauge5)水位控制器Water level controller6)过量蒸气调节阀Excess steam pressure control valve 4、舵机1)舵机间Steering room2)舵机装置Steering-gear3)手操舵装置Trick wheel plant4)油缸Oil cylinder5)反馈装置Feedback device6)舵Rudder舵叶Rudder blade舵杆Rudder stock上舵承Rudder carrier舵销Rudder pintle舵杆衬套rudder stock liner舵杆轴套Sleeve for rudder stock舵销承衬套Bush for rudder pintle舵销轴套Sleeve for rudder pintle上舵承底座Rudder carrier seat舵销承座Pintle bearing舵杆承座Rudder stock bearing挡圈Retaining ring舵柄Tiller舵角The angle of rudder5、空压机Air compressor1)主空压机Emergency air compressor2)应急空压机3)主空气瓶Main air reservoir4)应急空气瓶Emergency air reservoir5、控制空气瓶Control air reservoir6、空气干燥器Air dryer7、分油机Oil purifier1)燃油分油机Fuel oil purifier2)柴油分油机Diesel oil purifier3)滑油分油机Lubricate oil purifier4)排渣Sludge discharge8、制淡装置Fresh water generator9、焚烧炉Incinerator10、油水分离器Oil water separator11、生活污水处理器Sewage treat plant12、大气冷凝器Atmosphere condenser热水井Cascade and inspection(hot well)滑油自清滤器The automatic back-flash lubricating oil filter燃油单元Fuel oil unit1)主机燃油单元Fuel oil unit of M.E2)付机燃油单元Fuel oil unit of A.E3)粘度计Viscosity controller泵Pump1)主机滑油泵Main engine lubricating oil pump2)主机缸套水泵Main engine cylinder cooling waterpump3)主机缸套水预热泵Main engine cylinder cooling water preheating pump4)主机海水泵Main engine sea water pump365)主机燃油供给泵Main engine fuel oil supply pump6)主机燃油增压泵Main engine fuel oil booster pump7)主机十字头泵Main engine cross head pump8)付机海水泵Generator engine sea water pump9)付机缸套水泵Generator engine cylinder cooling water pump10)锅炉给水泵Feed water pump of boiler11)锅炉燃油泵Fuel oil pump of boiler12)分油机供给泵Fuel oil supply pump of purifier13)制淡海水泵Sea water pump of fresh water generator14)压载泵Ballast pump15)舱底消防泵Bilge and fire pump17)油渣泵Sludge oil pump18)柴油输送泵Diesel oil transport pump19)燃油油输送泵Fuel oil transport pump20)汽缸油输送泵Cylinder oil transport pump21)淡水输送泵Fresh water transport pump22)热水循环泵Hot water circulating pump23)饮水日用泵Drinking water pump舱底消防总用泵Bilge, fire and G.S pump喷淋泵Sprinkling pump停泊海水泵Harbor sea water pumpNotification of inspection 检查验收通知单Application 申请，申请单Inspection 检验，报验Technical discussion 技术讨论On board 在船上In the workshop 在车间On the slipway 在船台上At pier(wharf) 在码头Fair 尚好的The performance is merely fair 性能尚好Terrible 极坏的，很糟的So so 马马虎虎So far ,so good 到目前，一切顺利Worse更糟的worst最差、最糟Improvement 改进Leave no room for improvement 完美，无缺点Accept 接收Accept subject to 有条件的接收，有待于……做好之后才接收Reject 拒收Comments 意见defect lish 消除意见清单Item 项目memorandum 备忘录manual n、手册、说明书;a.手控的，手工的drawings 图纸working drawings 施工图finished drawings 完工图approved drawings 认可图drawings for approval 送审认可图supporting technical doucuments 基础技术文件sketch 草图draw a sketch画草图up to the standard 达到标准substandard 低于标准的crane 吊车building berth 船台slipway 船台、下水滑道dry dock 干无坞pier 突码头、突堤wharf 码头along side (船)靠码头foreman 工长，领班coordinator 调度员inspector 检查员supervisor 管理人、监督人，监造人surveyor 验船师。
船舶专业英语
船舶专业英语船舶类型词汇渔业船舶种类2.1 渔船fishing vessel用于商业性捕捉鱼类、鲸、海豹、海象或其他生物资源的船舶之统称。
2.1.1 拖网渔船trawler从事拖网作业，捕捞中、下层水域鱼虾类的专用渔船。
分双拖和单拖渔船，舷拖、尾拖和桁拖渔船。
2.1.1.1 双拖渔船two boat trawler，pair trawler，bull trawler由两船拖曳一顶网具进行捕捞作业的渔船。
2.1.1.2 单拖渔船single boat trawler由单船拖曳网具进行捕捞作业的渔船。
按作业方式可分为舷拖、尾拖和桁拖渔船。
2.1.1.3 舷拖渔船side trawler在船的一舷设有网板架，并进行拖网作业的渔船。
2.1.1.4 尾拖渔船stern trawler在船尾部进行拖网作业的渔船，称尾拖渔船。
单船尾拖设有网板架。
在尾部设起、放网滑道的称尾滑道拖网渔船（stern ramp trawler）。
2.1.1.5 桁拖渔船beam trawler有桁架伸于舷外，以拖曳网具进行捕捞作业的渔船。
2.1.1.6 加工拖网渔船factory trawler具有较大的冻结和加工能力的大型尾滑道拖网渔船。
2.1.2 围网渔船seiner从事围网作业，主要围捕中、上层水域鱼类的专用渔船。
包括双船及单船、舷侧起网及尾部起网灯光诱鱼、金枪鱼等围网渔船。
2.1.2.1 双船围网渔船two boat seiner由两船共放、起一顶围网进行捕捞作业的渔船。
2.1.2.2 单船围网渔船single boat seiner配有辅助船艇，单船放起围网进行捕捞作业的渔船。
2.1.2.3 灯光诱鱼围网船组light luring seiner group由一艘围网渔船，数艘诱鱼灯船以及保鲜运输船等组成的灯光诱鱼围网作业船组。
a.灯光诱鱼围网船light luring seiner利用水上及水下灯光诱集鱼群，进行围捕作业的渔船。
船舶英语词汇大全
船舶英语词汇大全一、船舶基本结构词汇1. 船体（Hull）：船舶的主体部分，包括船壳、甲板和舾装。
2. 船壳（Shell）：船体的外表面，起到防水、承重的作用。
3. 甲板（Deck）：船舶的顶部平面，用于行走、作业和装载货物。
4. 舷窗（Porthole）：船体两侧的窗户，用于通风和采光。
5. 舷梯（Jacob's ladder）：连接船舶与码头的小梯子，便于人员上下船。
6. 舵（Rudder）：控制船舶方向的装置，位于船尾。
7. 锚（Anchor）：固定船舶位置的器具，用于抛锚停泊。
8. 船锚链（Anchor chain）：连接船锚与船舶的链条。
9. 船舶龙骨（Keel）：船体底部的一条纵向构件，起到支撑作用。
二、船舶动力装置词汇1. 船舶主机（Main engine）：船舶的动力源，通常为柴油机或蒸汽轮机。
2. 船舶辅机（Auxiliary engine）：为船舶提供辅助动力的装置，如发电机、空压机等。
3. 螺旋桨（Propeller）：将主机产生的动力转化为推力的装置，位于船尾。
4. 柴油机（Diesel engine）：以柴油为燃料的内燃机，广泛应用于船舶动力装置。
5. 蒸汽轮机（Steam turbine）：利用蒸汽驱动叶轮做功的热力发动机。
6. 燃油喷射泵（Fuel injection pump）：柴油机燃油系统中，将燃油高压喷射到燃烧室的装置。
三、船舶导航设备词汇1. 罗经（Compass）：指示船舶航向的导航仪器。
2. 船用雷达（Marine radar）：用于探测船舶周围水域障碍物的电子设备。
3. GPS导航仪（GPS navigator）：全球定位系统导航设备，用于确定船舶位置和航迹。
4. 电子海图（Electronic chart）：显示海域地理信息的电子地图。
5. 船舶自动识别系统（S）：用于船舶识别、追踪和避碰的通信系统。
四、船舶通讯设备词汇1. 船用无线电（Marine radio）：用于船舶与船舶、船舶与陆地之间通信的无线电设备。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
船舶专业英文词汇船舶专业英语词汇（按照字母顺序排列）（一）a faired set of lines 经过光顺处理的一套型线a stereo pair of photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部advance coefficient 进速系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical ath Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积crow’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultative Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Society (IACS) 国际船级社联合会International Towing Tank Conference (ITTC) 国际船模试验水池会议intersection 交点，交*，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆*头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板welder 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇。