高压清洗机说明书
高压清洗机使用说明书及故障排除法和简单的维修处理
成都力锋产品使用说明书一、使用说明1、开机前的准备：a、开机前检查进水管过滤器安装正确。
b、开机前必须检查箱体机油到油窗一半。
c、开机前安装进水管，注意：进水管必须可靠连接（垫上進水管橡膠墊Φ26*Φ14）。
2、新机第一次使用时，可将过滤器先不装，将接过滤器一端与自来水管道连接，打开自来水阀门，按动清洗机主开关，使电机工作，待出水管出水量大于未开机状态时，再工作5秒左右，停机。
将工厂原配的过滤器可靠地连接后放入储水罐底部。
使用储水罐时，必须加注清洁的水源3、出水管连接：把高压胶管的接头与增压泵出水管口上的接头相连；另一头与水枪上的接头相连。
4、喷头选择本机所用的喷头一定要使用原厂提供的配套喷头5、清洗作业时，喷头与被清洗面得距离不宜太远，一般不超过10公分。
因喷头的冲击力是随喷射距离的增大而减小。
6、正常状态下，清洗压力不超过额定工作压力为宜，若有特殊需要时，也可将机器压力升到最高压力，但不建议机器在最高压力下长期运转。
7、清洗结束松开扳机关闭水枪后，本机器会自动关停电机。
若较长时间不使用机器，建议关闭电源开关，打开水枪扳机释放内部压力。
使用完毕，必须将水枪内压力完全释放8、使用时，泵体的泄水孔有水滴出，并不影响使用，属正常运行。
9、该机长时间闲置后使用：由于单相电机起动力矩较小，如按下起动开关，电机发出嗡嗡声（电机并不远转），应立即按停机按钮，反复二，三次，电机即能运转；如果电机仍然不能起动，请拆去电机风扇罩壳，用手转动风叶二，三周后，再启动电机。
并在停机状况下重新装好风扇罩壳。
二、保养1.每100小时更换一次机油，建议使用CD15W-40机油，正确使用机油对保证机器使用寿命非常重要。
2、如遇寒冷天气有结冰时或长期不用时，应将机内剩水排尽，方法是将进水管离开供水系统，开机脱水远转1分钟左右。
同时拆下进水管与出水管以排尽管中剩水。
高压清洗机内部积水结冰后会引起电机堵转，造成电机烧机等严重后果。
三、安全用电注意事项1、项目之安全检查a、经常检查电动机引接线是否牢固可靠完好无损。
高压清洗机的使用说明
当清洗封闭的区域，像储藏罐，放置泵和空 压机在外面，并远离罐体如果清洗的位置有 可燃物质适当的提供通风装置，做 适合的准 备，避免产生静电火花，参考当地的标准。
泵：使用接地线和卡子见FIG 2使用接地螺丝 （GS）和锁紧垫（LS）和附带的接地线（U） 在空气马达的后面，拧紧螺丝，另外一端， 接在直的地线上。
冲洗
冲洗前为了减少液体喷射的伤害的风险，静电 火花，喷溅，放压，移动喷嘴 使喷枪的金属部分和泄压阀紧靠在金属桶边， 然后开启枪和阀。
编辑ppt
13
启动
打开主气阀（D） 启动喷枪在接地的金属桶内，枪的金属
部分紧紧靠着桶。 缓慢打开调压阀（E）直到泵开始运行。 缓慢运行泵直至全部排出所有空气。释
编辑ppt
6
皮肤的喷射伤害
高压的液体从喷枪，或软管泄漏，破碎的配件，会刺入皮肤，看起来像割伤，但是 严重的伤害，引起切除，需要医学外科紧急处理。 1.不要用喷枪指着任何人或身体的任何部位。 2.不要把手放在喷嘴的前端。 3.不要用手、身体、手套、布片阻挡或导流泄漏。 4.没有安装喷射保护或触发保护就不要使用。 5.不喷时锁定触发锁。 6. 当喷射停止，在清洁、检查，维护设备前，遵守压力释放程序，
活塞和吸入的止回阀，排泄泵 247599在场家设定，用于低粘度 的液体，这样的设定对泵有最小的 冲击，调整这个阀用于高粘度的液 体。见操作手册
总是在液体被泵到底部前停泵如果 液体泵干喉部密封会损坏，完成泵 作业后放压。
如果你正在泵送的液体，干的，凝 固，快速凝结，尽可能多次用合适 的溶剂冲洗系统，避免在泵里或管 理形成干液
每操作40小时检查，密封螺母， 放压后拧紧螺母。拧的要合适，过 紧会引起密封损毁。
HD 1025 S型高压清洗机操作手册
HD 10/25 S型高压清洗机操作手册1 HD 10/25 S组成1手握喷枪2手握喷枪杆3高压管4喷枪托架5洗涤剂测量阀门6洗涤剂箱盖7洗涤剂箱8带过滤器的洗涤剂吸管9用于紧固环的螺丝10设备总开关11环12压力表13高压输出14喷头支撑15水管连接点16过滤器17液位显示18油箱19指示灯20软管存放位21洗涤剂箱排气孔22附件箱23绳索钩24管线轮25曲柄把手26把手27喷头28喷头标记29喷射杆30压力/流量控制31喷枪的安全销2为了你的安全在你第一次使用该清洁器时，请读这些操作说明和做好附带册《高压清洗的安全说明》的笔记。
3清洁器的使用该清洁器用来：1使用高压和清洁剂清洗（例如清洗机器、车辆、建筑和工具等）。
2使用高压但不用清洁剂清洗（比如清洗建筑物的正面、阳台、花园设备）对顽固污点，我们推荐爆破机作为附件。
4安全特性带有压力开关的减压阀。
当使用压力和流量控制减少流量时，减压阀打开同时一部分水回流到泵的吸水的一边。
如果喷枪的手柄松开，压力开关将关闭泵。
如果按下喷枪手柄，压力开关将打开泵。
流量阀和压力开关在出厂时就已经设定好了只有客服才能进行调整。
5清洁器使用准备5.1拆开清洗器箱1当拆开时，检查清单的内容。
如果有任何损伤请通知客服。
2不要把包装当家庭垃圾处理，把它放到适当的收集点用于循环利用。
5.2检查液位当设备停止使用时，检查油位。
油位必须在两个指针的上面。
5.3激活油箱排气孔1打开环的紧固螺丝并移走环。
2剪掉油箱盖的小尖。
3紧固设备的盖。
5.4装上附件1装上喷管的喷头。
2把喷管固定到喷枪上。
6接通清洗器6.1电源的连接警告：1电压必须和说明的一致。
2在电气说明的最大容忍的阻抗不能扩大。
3使用有效地横截面的延长线同时把它从卷筒上完全展开。
对于连接的载荷请看技术说明。
4通过插座把清洁器连接到电源上。
不允许直接连接到电源上。
插座用来断开和电源的连接。
6.2水的连接/供给操作连接到水源：1把供给管连接到在设备上的出水口，另一头接在进水口。
电动压力洗车机使用说明书
电动压力洗车机使用说明书一、产品介绍电动压力洗车机是一种高效、方便的清洗工具，适用于汽车、摩托车、自行车等各种车辆的清洗和护理。
本产品结构紧凑，操作简易，能够快速有效地去除车辆表面的污垢和油污，同时保护车漆不受损伤。
二、安全须知1. 请在使用前阅读本说明书，确保正确操作和使用产品。
2. 使用前，请检查电源线和机身是否完好无损，如有破损，请勿使用。
3. 请确保产品使用环境通风良好，以免电机过热影响使用寿命。
4. 使用时，请注意周围环境，避免水花飞溅到周边人员或物品上。
5. 使用时，避免将高压水枪对准人体或直接喷射到电子部件上，以避免触电或损坏设备。
6. 使用时，请勿长时间开启产品，以免电机过热。
三、组件及配件1. 压力洗车机主机2. 高压喷枪3. 水管4. 不同喷头5. 进水过滤器6. 使用说明书四、使用方法1. 安装准备1. 将进水过滤器连接到自来水龙头上，并确保连接牢固。
2. 将水管连接到进水过滤器上。
3. 将另一端的水管连接到洗车机的进水接口上。
4. 确保所有连接部位无漏水。
2. 启动产品1. 将插头插入交流电源插座。
2. 打开自来水龙头，确保水源供应充足。
3. 按下洗车机上的启动按钮，主机开始工作。
3. 使用喷头1. 根据清洗需求，选择合适的喷头。
2. 插入喷头到高压喷枪的接口上，并旋紧。
3. 按下高压喷枪的扳机，开始清洗车辆。
4. 可根据需要调整喷头的角度和喷射压力。
4. 清洗车辆1. 从车辆的上部开始，由上到下地清洗表面污垢。
2. 使用喷枪将水流对准污垢，保持适当的距离和角度。
3. 清洗时，可以根据需要调整喷头的喷射方式，如扇形、锥形等。
4. 清洗车轮时，可选择较高的压力，以清除附着在轮胎表面的油污和泥土。
五、维护保养1. 清洗完成后，请切断电源，并关闭自来水龙头。
2. 请在使用前、使用后清洗喷头，并保持干燥。
3. 如长时间不使用，请将电动压力洗车机存放在干燥通风的地方，避免阳光直射。
高压清洗机使用说明书及故障排除法和简单的维修处理精编版
高压清洗机使用说明书及故障排除法和简单的维修处理公司标准化编码 [QQX96QT-XQQB89Q8-NQQJ6Q8-MQM9N]成都力锋产品使用说明书一、使用说明1、开机前的准备：a、开机前检查进水管过滤器安装正确。
b、开机前必须检查箱体机油到油窗一半。
c、开机前安装进水管，注意：进水管必须可靠连接（垫上进水管橡胶垫Φ26*Φ14）。
2、新机第一次使用时，可将过滤器先不装，将接过滤器一端与自来水管道连接，打开自来水阀门，按动清洗机主开关，使电机工作，待出水管出水量大于未开机状态时，再工作5秒左右，停机。
将工厂原配的过滤器可靠地连接后放入储水罐底部。
使用储水罐时，必须加注清洁的水源3、出水管连接：把高压胶管的接头与增压泵出水管口上的接头相连；另一头与水枪上的接头相连。
4、喷头选择?本机所用的喷头一定要使用原厂提供的配套喷头5、清洗作业时，喷头与被清洗面得距离不宜太远，一般不超过10公分。
因喷头的冲击力是随喷射距离的增大而减小。
6、正常状态下，清洗压力不超过额定工作压力为宜，若有特殊需要时，也可将机器压力升到最高压力，但不建议机器在最高压力下长期运转。
7、清洗结束松开扳机关闭水枪后，本机器会自动关停电机。
若较长时间不使用机器，建议关闭电源开关，打开水枪扳机释放内部压力。
使用完毕，必须将水枪内压力完全释放?8、使用时，泵体的泄水孔有水滴出，并不影响使用，属正常运行。
9、该机长时间闲置后使用：由于单相电机起动力矩较小，如按下起动开关，电机发出嗡嗡声（电机并不远转），应立即按停机按钮，反复二，三次，电机即能运转；如果电机仍然不能起动，请拆去电机风扇罩壳，用手转动风叶二，三周后，再启动电机。
并在停机状况下重新装好风扇罩壳。
二、保养1.每100小时更换一次机油，建议使用CD15W-40机油，正确使用机油对保证机器使用寿命非常重要。
2、如遇寒冷天气有结冰时或长期不用时，应将机内剩水排尽，方法是将进水管离开供水系统，开机脱水远转1分钟左右。
高压清洗机说明手册
高压清洗机说明书型号:TVE070C、TVF070CTVB080G、TVD100CTVG100C自行用时存放在室内。
本机供应电流应不少于额定电流。
使用前，请先检查延长电线，如果已损坏，请更换。
使用不适合的外延电线会有很大的危险。
不要滥用延长电线，拔插头时请不要猛拉电线。
延长电线远离热源及锋利刀口。
分离本机时，请先将插头从插座处分离。
警告：如果供给电线已损坏，必须使用专用的电线，也可让销售商或生产厂家重新装配。
警告：为了减少触电风险，在下雨和雷雨天气不要开启和操作本机。
保持所有接口干燥，并脱离地面，不要用湿手触摸插头，严禁水渗透本机。
警告：本机运行时，必须保持持续的供水，没有水循环温度将会达到危险点，会引起机内密封圈的损坏。
警告：不要使用本机用于特别寒冷处，以防止冰冻而损坏本机。
警告：此机设备只为清洁水设计，不能使用腐蚀性的化学液体。
警告：不能将本机直接对准人体、宠物及机器本身喷射。
警告：在维修保养时，必须切断电源。
警告：为了确保实用安全，请用最初的备用配件及生产商指定的配件。
假如机器损坏，没有修复以前请不要使用本机。
操作指南－连接软管到出水口，并连接喷抢到软管另一头。
－连接喷头和喷杆。
－查看过滤网是否有障碍物。
－连接供水软管。
－主要技术数据维修保养安装Array连接图１主机２供水软管３水管接合配件４进水口５高压管６自来水龙头７喷枪８电源插头注意：假如产品更新，公司将保留没有预先通知的情况下，修改说明书的权利。
利索牌超高压清洗机使用说明
利索牌超高压清洗机使用说明
1、开机前的准备：
a、开机前检查进水管过滤器安装正确。
b、开机前必须检查箱体机油到油窗一半。
C、开机前安装进水管，注意：进水管必须可靠连接（垫上進水管橡膠垫中Φ26*中14)
2、新机第一次使用时，可将过滤器先不装，将接过滤器一端与自来水管道连接，打开自来水阀门，按动清洗机主开关，使电机工作，待出水管出水量大于未开机状态时，再工作5秒左右，停机。
将工厂原配的过滤器可靠地连接后放入储水罐底部。
使用储水罐时，必须加注清洁的水源
3、出水管连接：
把高压胶管的接头与增压泵出水管口上的接头相连；另一头与水枪上的接头相连。
高压清洗机手册（M12110 M12230）说明书
M12110M12230Instruction ManualSpare Parts ManualProduct information................................................................................................Important safety instructions...................................................................................Technical specification............................................................................................Know your machine................................................................................................Working principle....................................................................................................Preparing for use...................................................................................................Assembly...............................................................................................................Brush selection guide............................................................................................Controls..................................................................................................................Operating the machine...........................................................................................Electrical diagram..................................................................................................Accessories...........................................................................................................Upkeep of your PORT A SCRUB...........................................................................Housing - Drive Side...............................................................................................Housing-Idle Side..................................................................................................Pump housing........................................................................................................Lever and guide link mechanism............................................................................Handle group..........................................................................................................Motor,drum and bridge assembly...........................................................................Accessories...........................................................................................................3345556677,88991113,151719212325The Minuteman Machine is an ideal machine to clean floors in small and medium areas like offices,hospitals,restaurants,shopping complexes and many commercial applications.It sprays plain water /detergent solution,scrubs and picks up the dirty water -all in a single pass.The Port A Scrub has different optional brushes to suit a variety of applications.This machine can be used only on smooth even floors like Mosaic,all type of stone floors,PVC,Short-pile carpet,Wood and Profiled Rubber.It should not be used on rough uneven surfaces..PORT ASCRUB Instruction ManualThe machine must be unpacked and assembled in accordance with these instructions before connecting to the electrical supply.This machine should always be connected to a fully grounded power supply of the right voltage and frequency.Keep the power supply cord away from moving parts.During operation,hazard may occur when running machine over the supply cord.The machine must be disconnected from the mains supply (by pulling the plug out)before changing the brushes,cleaning the machine and,for maintenance.Warning!Use only the brushes/accessories strictly as per the instruction age of any other brushes/accessories can cause safety problems.Periodically inspect the cord for possible damage.The damaged cord must be replaced with the special cord available from the manufacturer or an authorized service agent.DO NOT leave the machine connected to the power supply when not in use;always remove the plug from the mains socket.DO NOT use where hazardous dust is present.DO NOT use machine near flammable liquids.DO NOT use in an explosive atmosphere.DO NOT use in gradient surface.DO NOT keep the machine with handle lowered,when the machine is in working mode.Operators must be fully trained in accordance with these instructions,able to perform routine upkeep of the machine and correct selection of brushes.Operators should be physically capable to maneuver transport and operate the machine.DO NOT run the machine dry,as this could damage the floor surface or the machine itself.Take adequate care to hold the machine firmly while installing and removing the brush.Never use excessive foaming or highly corrosive cleaning solutions.While operating on a flooded floor,always ensure that the water level does not exceed 1/4”.DO NOT operate this machine on rough uneven surface like industrial concrete floor.Do not clean the machine using water jet.Ensure all parts are fitted properly before operation.···········Guidelines for the operator (3)4Note:1. Noise levels measured at a distance of 1 meter from machine and 1.6 metres above floor, when washing a hard floor. Measurements recorded using a hand held meter.2. Handle vibration does not exceed 2.5 m/s, when operating on a smooth hard surface.3.Above dimensions are approx. Since the companies policy is to continuously improve the product, there could be changes without prior notice.2986713511412312(1)(2)(3)Tank(4)Bottom handle (5)Dirty water tank(6)Filter (7)Lid Cap (8)Boot(9)Nozzle (10)Conveyor drum (11)Brush (12)PedalTop handleLiquid discharge controlhandle1.Cleaning liquid in the fresh water tank is made to spray on the floor to be washed..2.The counter rotating brushes scrubs the floor and also throws the dirty water on the Conveyor drum.The front brush does most of the scrubbing and drying.The rear brush completes the scrubbing and collects the remaining water off the floor.3.A blade fitted to the dirty water tank wipes the drum.1. Bottom handle2. Machine body3. Pump Housing4. Auxillary Tank5. Top handle &pull cable7. Brush shafts (2)8. Screws & washers 9. Cable retainer 10. Power cord6. Handle LH & RH11. Dirty water tank 12. Hook 13. Knob (10)(11)(12)(7)(8)(9)(6)(2)(3)(4)(5)(1)L E F T B O T TO M R E A RR I GH T B O T TO M R E AR 1.Insert the two tubular handles into the bottom handle and secure them using knob (2Nos)by tightening lightly.Ensure that the handles are assembled according to their marked position and the cable holding hooks are pointing towards the rear.2.Slide the electric cable retainer into the top portion of RH handle.3.Fit the top handle over the tubular handles and secure them with washer and screw (2sets).Ensure that the label on the top handle is facing the front of the machine.Now tighten firmly both the knobs and screws alternately.Insert the dummy caps provided to cover the screws (2nos)in the top handle.4.Pass the free end of the pull cable through the plastic guide in RHHandle.5.Fixthe auxillarytank firmly into the bottom handle by holding the top handle.6.Rotate the knob to hold the auxillary tank.7.The brushes are only loosely packed in the machine for transit,therefore the brush shafts must be fitted before operating the machine.Push the shafts through the brushes from the side of the machine.To remove brushes,push the brush shaft out from the side of the machine using the fingers and withdraw the shaft.Normally standard brush type will be supplied with the machine.Brushes shall be selected according to the type of floor surface to be cleaned,and the degree of dirt to be removed,please refer Brush Selection Guide.8.Now machine is ready for use.6Refer Page 25 for Brush SelectionThis is applicable when the customer has more than one set of brushes of same type.Example :2or more sets of Standard BrushCustomers may not interested to use same brushes in Bedroom /Kitchen /germ free area which is already been used in other areas like Corridor /Bathroom /Oil or chemical deposited areas.It is difficult for the customers to identify the particular brush which is used in certain area.To make this easy,Brush buttons of colors RED,BLUE,WHITE and YELLOW are packed with the machine.Customers shall plug the buttons on the hole provided in the brush as shown.This helps the customer to identify the particular brush by keeping the button (color)as reference.(a) Hole provided for plugging button.(b) Brush with button plugged.By pressing the pedal lightly with your foot,pull back the handle a little to start the motor.The brushes and the drum starts rotating.Pulling the handle further without pressing the pedal,lowers the machine and engages the rotating brushes onto the floor.To stop working,take the handle to the vertical position.By pulling,the liquid discharge control handle up,the cleaning liquid is made to spray on the floor.The spraying stops once the liquid discharge control handle is released.Brush contact with the floor is adjustable in 4steps,contact is MINIMUM when the knob is fully down and MAXIMUM when it is fully raised.This helps you to compensate for the wear of brushes and also to control the scrubbing effect.If there is no machine movement,when the handle lower down fully (working mode),change the knob position to one step up.In the event of motor getting overloaded due to improper power supply or unexpectedobstruction to the brush/drum rotation,the over load protector trips and protects the motor from damage.If this happens,identify the cause,correct it and,reset the protector button after minimum 30seconds from tripping by pressing the over load protector manually and continue working.Slide this knob to TOP position to operate the machine.Slide this knob to BOTTOM position to move the machine from one place to other place and to park the machine.By keeping the knob to top position (working mode)and moving the machine will damage the brushes.Before the washing operation startsRecommended washing sequenceTransport/Working Model ControlBrush Contact ControlCleaning Liquid Discharge ControlMotor Overload Protector1. Fill cleaning liquid in fresh water tank (Fig-i)2. Insert the plug into mains 3-pin socket.3.Ensure that the brushes are fitted properly.4.Slide the transport/working mode control knob to TOP (working) position (Fig-ii).1. Start the machine by pressing the pedal and pulling the handle back.2. Move forward, while sparingly pulling the liquid discharge control handle (Fig-iii).This handle should not be kept pulled all the time.The duration and frequency of pulling and releasing has to be adjusted suitable to match with the type of floor, extent of dirt. etc. For ceramic & granite floors, apply very little water.7(Fig-v)5.When the dirty water tank is full,lift and pull the tank out of the machine (Fig vi).Empty the tank and wash it in running water or dip it in a bucket of water (Fig-vii).Clean the blades and push the tank into its place.1.Move the Transport /Working mode control knob to BOTTOM (Transport)position (Fig-viii).2.Disconnect the power supply by unplugging the electrical plug and wind the cable over cable holders in the handle.3.Pull out the dirty water tank and wash it completely.4.To prevent possible clogging of filter,drain cleaning liquid5.Remove the brushes by pushing the brush shaft out (Fig-ix).6.Wash the brushes either by dipping in a bucket/sink or in running water (Fig-x).7.Turn the machine sideways and wipe clean the conveyor and machine body with a damp cloth (Fig-xi).8.Re-install the brushes after washing.It is easier to push the brush shaft form the right hand side (identified by the electrical cable).9.Keep the machine in the safer place.may not handed overTransporterSide BrushTo get the maximum life of the machine ensure the following.Regularly inspect sheath,plug and cord anchorage for damage or loose connection.For maximum life wash the brushes regularly.Ensure machine is in Transport mode when not in use.Store additional brushes in a vertical position to avoid bending of bristles.Check for permanent bending of bristles in a particular direction.This may occur if the machine is operated for several days without removing the brushes,which is not recommended.If this occurs,reverse the brush so that the bent bristles are automatically straightened.This may wear out after years of use.If this occurs the water collection performance will decrease.It should be replaced by an authorized ServiceAgent.The filter prevents clogging of the spray nozzle and should be periodically e pressurized air/water for cleaning.If the spray of the nozzle become blocked,slide the nozzle cover off and remove nozzle wash in clean water and clean using a pin and refit.·Supply cordBrushesWiper BladeSolution feed filterNozzle maintenance (9)The simply fitted trolley provides for ease of movement when transporting the machine.Installing the Transporter1.With the machine handle in the upright position place the transporter centrally alongside the machine.2.By holding the machine firmly, strap the velcro with the machine to fix the transporter.3.Ensure that the velcro strap properly wrapped around the bottom handle.4.Now the transporter is ready to use.The machine can then be maneuvered easily whilst holding the top handle.To wash the edges,the side brush shall be used.Switch off and unplug the machine before fitting the side brush.1.Remove the front brush and brush shaft.2.Fix the shield assembly and screw it into the side plate and tighten.3.Insert the side brush through the shield and main brush.Fitting the side brushUsing the side brush1.Tilt the machine at an angle move forward.This way,the dirty water thrown bythe side brush will be collected by the rear brush.e side brush only for washing the edges.322524105116116a11115b1949848319539787208880114101919728115a115b111914359427313V81034 9211563V71911193622122774610Housing-Drive Side Spare Parts ManualRef. No PartNoDescription Size Qty1925032CSK SCREW M4x104 2925003CRPH SCREW M3x66 7925051CSK SCREW M6x143 9925114ALLEN SCREW M6x102 10925027ALLEN SCREW M6x167 11925031ALLEN SCREW M6x202 13925033WASHER 4.2x12x1.64 19925056BEARING60032RS9 20925062BEARING6082Z1 24925001BELT5005M1 25925002BELT4255M1 28925012WASHER2 32925018BUMPER1 34925026BUMPER1 42925047BRUSH SLIDER1 43925048SLIDER HOUSING1 46925054SEAL2 49925064PINION1 53925073DRUM SPROCKET1 59925092PIN1 62925099O'RING2 63925102SHIELD1 73925186SELF TAPPING SCREW4 77925130CAP2 80925227GEAR HOUSING1 83925181HOUSING SPROCKET1 84925182SEAL1 87925193GEAR–LH1 88925194GEAR-RH1 92925219SHIELD2 93925220ROLLER2 105925249BUMPER SLEEVE3 111925804BRUSH SPROCKET2 114925813GEAR SPROCKET2 115925815IDLER ASSY1 115a925075SPROCKET1 115b925046HUB2 116925816IDLER ASSY1 116a925061SLEEVE1 212925221STUB AXLE1 V7925150DRIVE HOUSING1 V8925319COVER1V2V3133751094b94a 9412986131132892172736811610039909596999893622123318868171061524218919792774632105V5910V834137358594319263Housing-Idle SideRef. No PartNoDescription Size Qty1925032CSK SCREW M4x104 2925003CRPH SCREW M3x66 6925039CSK SCREW M5x252 9925114ALLEN SCREW M6x102 10925027ALLEN SCREW M6x165 13925033WASHER 4.2x12x1.64 15925100WASHER 6.4x12x1.61 16925151WASHER9x17x1.61 17925110SPRING WASHER M61 18925059TOOTHED WASHER M61 19925056BEARING60032RS2 21925063WIRE TIE3 32925018BUMPER1 33925019BUSH2 34925026BUMPER1 39925040STUB AXLE1 43925048SLIDER HOUSING1 46925054SEAL2 58925083TRANSPORT SLIDER1 59925092PIN1 62925099O'RING2 63925102SHIELD1 68925109FAN COVER1 72925116GROMMET1 73925186SELF TAPPING SCREW6 75925124CAP1 77925130CAP2 79925147STOPPER1 81925500PEDAL1 86925192NUT2 89925199CONNECTOR1 90925200SWITCH2 92925219SHIELD2 93925220ROLLER2 94925529SOCKET ASSY1 94a925074SOCKET1 94b925076TERMINAL3 95925501CABLE1 96925502CABLE1 98925504CABLE1 99925505CABLE1V2V3133751094b94a 9412986131132897273681161003990959699982193622123318868171061524218919792774632105V5910V834137358594319263Housing-Idle SideRef. No PartNoDescription Size Qty100925152SPRING-PEDAL1 105925249BUMPER SLEEVE3 106925161CSK SCREW M4x81 129925015LEVER SWITCH ACT1 131925041INSULATION TOP1 132925044INSULATION BOTTOM1 133925101NUT1 188925207SLEEVE TIE ROD3 212925221STUB AXLE1 242925347CLAMP WIRE1 V2925534CAPACITOR(M12230)1 V3925173CIRCUIT BREAKER(M12110)1 925166CIRCUIT BREAKER(M12230)1 V5925153IDLE HOUSING(M12110)1 925154IDLE HOUSING(M12230)1 V8925319COVER11651871841183M12110185180159124516818116472244V2155101176V9169186182163167158154174173121123123a122b16224724627117010272175177248165270Pump HousingRef. No PartNoDescription Size Qty1925032CSK SCREW M4x105 72925116GROMMET2 101925160O-RING-PUMP1 102925077FILTER1 121925832DIRTY WATER TANK1 122b925162LID PAD2 123925836LID-DIRTY WATER1 123a925132LID-DIRTY WATER1 154925128HOSE-275(10.8)1 155925163INSULATION1 158925164HOSE CLIP1 159925165NOZZLE1 162925167BOOT1 163925168SCREW M3X302 164925169HEX NUT M32 165925170HEX NUT M47 167925187SWITCH2 168925204STRIP LID2 169925224EXTENSION BUSH1 170925233HOSE-165(6.5)2 173925261HOSE CONNECTOR1 174925262BOOT-LID1 175925506CABLE1 176925511ADAPTOR NOZZLE1 177925573CABLE1 180925171SEAL NOZZLE1 181925173BASE SWITCH1 182925174LEVER1 183925175CLAMP1 184925176SUPPORT RING2 185925177PUMP HOUSING1 186925178LID1 187925179SPACER1 245925013CSK SCREW4 270845039WASHER4 V9925210PUMP(M12230)1For M12110244925011CLAMP CAPACITOR(12110)1 246925016GROMMET(M12110)2 247925020PUMP HOUSING(M12110)1 248925021CABLE(M12110)1 271814313CSK SCREW M4X154 v2925536CAPACITOR(12110)1 v9925203PUMP(M12110)1119a118a1196411876264128120120a119a82119297841477691267611345Lever and Guide Link MechanismRef. No PartNoDescription Size Qty4925104CRPH SCREW M4x122 26925008CLEVIS PIN5 29925014CLEVIS PIN1 41925043LINK1 45925053SHIELD8 47925055LEVER2 64925105LEVER BUTTON4 76925129CIRCLIP6 78925139LINK GUIDE1 82925180SPRING1 91925212BUSH1 113925810WHEEL4 118925822LEVER ASSY1 118a925085LEVER1 119925823LEVER ASSY2 119a925086LEVER2 120925824LEVER ASSY1 120a925087LEVER1 128925050LEVER SWITCH1V423355718936010415344711211748114135126124172160160a 160c 160b 179161d 161161c 161b 161a 15222423173229225732306545222522722866224226Handle GroupRef. No PartNoDescription Size Qty3925058CRPH SCREW M4x81 4925104CRPH SCREW M4x1210 11925031ALLEN SCREW M6x202 12925088WASHER 6.4x18x24 23925098CABLE RETAINER1 35925028CLAMP1 44925049PULL HANDLE1 48925057CAP1 52925069BASE-CABLE HOLDER2 57925082CLAMP1 60925096NUT1 65925106SPRING6 66925107WASHER6 71925115PLUG2 73925186SELF TAPPING SCREW10 104925184PULL CABLE-P1 117925818TOP HANDLE1 126925103KNOB2 135925089BOTTOM HANDLE1 152925127GASKET1 153925111TANK-4l1 160925117BASE VALVE1 160a925118BASE1 160b925119SEAL1 160c925120CAP-VALVE1 161925135VALVE1 161a925122BODY-VALVE1 161b925540SEAL1 161c925123SPRING1 161d925125CAP-SPRING1 172925260PLATE1 179925126NUT1 189925274SLEEVE1 224925305KNOB-CABLE HOLDER-II2 225925306KNOB-CABLE HOLDER-I2 226925307KNOB-TANK HOLDER-LH1 227925308KNOB-TANK HOLDER-RH1 228925339BASE-CABLE AND TANK HOLDER2 229925340GUIDE1 230928633PIPE-LH1 231928634PIPE-RH1 V4925922(M12116)POWER CORD1 925920(M12235)POWER CORD1 925923(M12235)POWER CORD-UK1134134b134aV6287V15011227315415556623755381422677069851Motor, Drum and Bridge AssemblyRef. No PartNoDescription Size Qty5925136HEX NUT M63 7925051CSK SCREW M6x144 8925090ALLEN SCREW M4x102 14925080WASHER 5.2x10x1.62 15925100WASHER 6.4x12x1.63 22925084GRUB SCREW M5x122 27925009BUSH4 28925012WASHER4 31925017WASHER6 37925037SPRING1 38925038SPRING1 50925065HEX SHAFT2 51925068WASHER2 54925078TIE ROD3 55925079SHAFT1 56925081ROLLER6 62925099O'RING12 67925108BUSH2 69925112BUSH1 70925113BUSH1 112925808BRUSH SHAFT2 134925067DRUM ASSY1 134a925070DRUM1 134b925071DRUM SLEEVE1 V1925762MOTOR(M12110)1 925761MOTOR(M12230)1 V6928548BRIDGE1AccessoriesSide Brush Group-3423456176886a6a6b6c9112101011103254TransporterAccessories1234566a 6b 6c 789101112925881925155925156925157925158925137925138925140925141925159925142925143925144925878925879FRAME CLAMPFIXED STRIP (VELCRO)FLEXIBLE STRIP(VELCRO)PLATE TYREBUSH-WHEEL RIM WHEEL RIM TYRE-MAIN WHEEL CAP WHEEL WASHER CIRCLIP A17x1CRPH SCREW M4x25STOPPER TOP STOPPER BOTTOM925904-TRANSPORTER 111112422242612SL NO PART NO DESCRIPTIONQTY12345925901925902925903925908925990BRUSH GROUP-STD BRUSH GROUP-POLISHING BRUSH GROUP-SCRUBBINGBRUSH GROUP-ESCALATOR (NYLON)BRUSH GROUP-ESCALATOR (SILICON CARBIDE)BRUSH GROUP SL NO PART NO DESCRIPTION123456SHIELD BUSH SHAFT SIDE BRUSH WASHERALLEN SCREW M5x20SIDE BRUSH GROUP DESCRIPTION SL.NOQTY 925766925172925764925855925145925146925907STANDARD 925766925172925764925595925145925146925927ESCALATOR 111111Note:Since the companies policy is to continuously improve the product, these could be changed without prior notice.Minuteman International Made Simple Commercial Limited WarrantyREVISION DEFFECTIVE 7/1/2008Minuteman International, Inc. warrants to the original purchaser/user that the product is free from defects in workmanship and materials under normal use. Minuteman will, at its option, repair or replace without charge, parts that fail under normal use and service when operated and maintained in accordance with the applicable operation and instruction manuals.All warranty claims must be submitted through and approved by factory authorized repair stations.This warranty does not apply to normal wear, or to items whose life is dependent on their use and care, such as belts, cords,switches, hoses, rubber parts, electrical motor components or adjustments. Parts manufactured by Minuteman are covered by and subject to the warranties and/or guarantees of their manufacturers. Please contact Minuteman for procedures in warranty claims against these manufacturers.-- Use of replacement filters and/or prefilters not manufactured by Minuteman or itsdesignated licensees, will void all warranties expressed or implied.A potential health hazard exists without original equipment replacement.All warranted items become the sole property of Minuteman or its original manufacturer, whichever the case may be.Minuteman disclaims any implied warranty, including the warranty of merchantability and the warranty of fitness for a particular purpose. Minuteman assumes no responsibility for any special, incidental or consequential damages.This limited warranty is applicable only in the U.S.A. and Canada, and is extended only to the original user/purchaser of this product. Customers outside the U.S.A. and Canada should contact their local distributor for export warranty policies.Minuteman is not responsible for costs or repairs performed by persons other than those specifically authorized byMinuteman.This warranty does not apply to damage from transportation, alterations by unauthorized persons, misuse or abuse of the equipment, use of non-compatible chemicals, or damage to property, or loss of income due to malfunctions of the product.If a difficulty develops with this machine, you should contact the dealer from whom it was purchased.This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions and limitations may not apply to you.MPV 13, one year partsV-14, One year parts, one year laborMPV 14 and 18, two years parts, one year labor RapidAir blower, one year parts, one year laborExplosion-Proof Vacuum, one year parts, one year labor Pneumatic Vacuums, three years parts, one year labor TRS 14, one year parts, one year labor(Not to exceed two hours)(Not to exceed two hours)(Not to exceed two hours)Ninety days0-3 months replacement, 4-12 months pro-rate Ten years, no additional labor111 South Rohlwing Road Addison, Illinois 60101 USA Phone 630- 627-6900Fax 630- 627-1130Special warning to purchaser Three years parts, two years labor, ninety days travel (Not to exceed two hours)Port-A-Scrub, one year parts, six months laborThree years parts, two years labor, ninety days travelSweepers, one year parts, one year labor, ninety days travelOne year parts, one year labor, ninety day travelOne year replacement Cord Electric Group……….Battery Operated Group…..Internal Combustion Group….Battery Chargers Replacement Parts Batteries Polypropylene Plastic Tanks Exceptions……….Exceptions……………………. ..EX 12 and EX12H, one year parts, one year labor ……………..………………………….…European Representative Andre VonkHako-Minuteman-PowerBoss PO Box 174。
高压清洗机使用说明书
高压清洗机使用说明书高压清洗机使用说明书1. 产品概述高压清洗机是一种用高压水流清洗污垢、去除油污的设备。
本文档将详细介绍高压清洗机的使用方法，以确保用户正确、安全地操作。
2. 安全注意事项在操作高压清洗机之前，请务必遵循以下安全注意事项：- 请使用合适的防护设备，如护目镜、手套和防护服等。
- 在使用高压水流时，请确保周围没有人员或动物，并确保有足够的通风。
- 在清洗机开启前，请确保电源已关闭。
- 不要将高压喷嘴对准人体或动物，也不要将水流直接喷射到电子设备或电气设备上。
- 如果发生任何故障，请立即关闭电源，并联系专业维修人员进行修理。
3. 使用方法步骤1：准备工作1. 将高压清洗机放置在平稳的地面上，并确保电源线连接稳固。
2. 检查高压清洗机的各个部分是否完好无损，如电源线、水管和喷嘴。
步骤2：连接水源1. 将水源的水管连接到高压清洗机的进水口，并确保连接稳固。
2. 打开水源并检查水流是否正常。
步骤3：开启设备1. 插入电源线到电源插座，并确保电源线连接稳固。
2. 打开高压清洗机的电源开关。
步骤4：调整喷嘴1. 根据清洗需求，选择合适的喷嘴。
2. 将喷嘴连接到高压清洗机的喷嘴接口，并确保连接稳固。
步骤5：开始清洗1. 按住喷嘴，将水流对准需要清洗的物体。
2. 保持适当的距离，并移动喷嘴以覆盖整个清洗区域。
3. 如需调整水流强度，可旋转喷嘴上的调节钮。
步骤6：关闭设备1. 清洗完毕后，先关闭高压清洗机的电源开关。
2. 关闭水源，并拔出水源的水管。
4. 清洁与维护- 在使用高压清洗机前，请确认清洗机的各个部位是否干净，并及时清理积存的污垢。
- 每次使用后，请将高压清洗机放在通风干燥的地方晾干。
- 定期清洗和更换过滤器以确保高压清洗机的正常工作。
- 如果发现异常情况或故障，请及时联系专业维修人员进行检修。
5. 故障排除以下是一些常见的故障及解决方法：1. 故障：高压清洗机无法开启。
- 解决方法：检查电源插座是否正常，确认电源线是否连接稳固。
高压清洗机 K 3 操作说明书
在初次操作机器前，请阅读并遵守这些操作说明，保存好操作说明，以便以后使用或后续所有者使用。
—在初次启动之前，必须阅读第5.956-251.0号安全信息！—如果不遵守操作说明和安全说明，会导致机器损坏，对操作人员和其他人造成危险。
—如果存在运输损坏，请立即通知销售方。
目录环境保护CH 1 操作说明中的符号 CH 1 正确使用 CH 1 概述 CH 2 启动 CH 2 操作运行 CH 3 清洗方法 CH 4 运输 CH 5 存放 CH 5 维护和保养 CH 5 故障检修 CH 6 附件和备用零件 CH 6 担保 CH 7 EC 符合性声明 CH 7 技术规格CH8包装材料可以回收利用。
请不要把包装放在普通垃圾中进行处置，应安排进行正确的回收利用。
旧机器含有可以回收利用的有价值的材料。
电池、油和类似物质不得进入环境中。
请使用合适的收集系统处置旧机器。
内部材料提示内部材料提示（（REACH ）最新的内部材料信息请您在如下连接中查找：/REACH危险即刻引发威胁的危险，致使身体严重伤害或死亡。
警告潜藏的危险情况，致使身体严重伤害或死亡。
注意潜藏的危险情况，可能致使身体轻微伤害或损伤。
本机器为地毯湿式清洗机器，用于商业使用，请遵守操作说明以及随附的“刷式清洗机器和喷洒抽吸机器的安全指示”手册中的安全说明。
快速入门说明图示A1把喷洒/抽吸软管连接到机器上。
2 把喷洒/抽吸软管连接到弯头上。
3 制备清洗溶液，注满清水箱4 选择操作模式5 清洗6 排空清水箱7 抽吸地面管嘴的托盘8 清洗污水箱排空污水箱9 注满清水箱（没有洗涤剂）10 冲洗机器11 清洗绒布过滤器，清洗清水滤网12 让机器干燥机器部件图示B1 转接头安装点（homebase）2 电源线3 铭牌4 附件转接头（homebase），包括电缆钩5 转接头安装轨（homebase）6 踏板7 加注量显示器8 握把9 推动手柄，可调节10 护盖锁定装置11 滑块拧紧螺钉12 附加的刷子清洗头PW 30/1的插座13 抽吸管夹持件14 护罩15 清水筛网，包括盖子16 转向辊轮，带固定位置制动器17 地面管嘴存放处18 清水箱盖子19 操作区域20 喷洒软管接头21 抽吸软管接口22 地毯清洗地面管嘴23 地毯转接头24 地面管嘴解锁装置25 抽吸管26 管嘴口27 连接头28 附加手柄29 弯曲件30 歧管上的杆件31 喷洒软管32 抽吸软管33 喷洒/抽吸软管34 清水箱35 污水箱提手36 污水箱，可拆卸37 浮子螺钉38 浮子39 过滤器外壳40 扁平折叠过滤器41 快速入门说明42 绒布过滤器43 护盖密封操作区域图示C1 0/关2 操作模式：喷洒3 操作模式：抽吸4 操作模式：喷洒/抽吸5 旋钮→每次使用之前，检查大功率电缆、延长电缆和软管是否损坏。
北星高压洗车机械说明书
TM MA1578111F.2ITEM NUMBERS : A1573701, A1573981, A1577541,A1578111, A1578171, A1578131, A1578181, A1578151, A1578201A1578203, A1578173Owner’s Manual Pressure Washer Pump: For high pressurecleaning machines.Any Questions, Comments, Problems or Parts OrdersCall NorthStar Product Support 1-800-270-0810Pump is shipped with oil.- Remove shipping plug and install vented fill cap. (Comet Pumps)- Remove shipping tape from pump oil fill cap. (Cat Pumps)- Remove shipping plug and install dipstick. (General Pumps)- Remove shipping plug and install dipstick. (NorthStar Pumps)- See pump oil cap section of this manual.Closely inspect all components.-If you have damaged components then: Contact the freight company that delivered the unit and file a claim.-If you have missing components then: Contact Customer Service at1-800-270-0810.Read this manual.Serious injury or death can result if safety instructions are not followed.WARNINGHazard Signal Word DefinitionsTable of ContentsInstructions (8)Specifications (14)Parts Explosions (15)WARNING1.) Read owner's manual completely.Serious injury or death can result if safety instructions are not followed. You must be 16 or older to operate this machine. Keep untrained people away.2.) Skin puncture hazard.High pressure fluid can inject under skin resulting in serious injury including amputation. Do not direct spray at people or animals.-If skin injection happens, seek IMMEDIATE surgical treatment.-Do not check for leaks with hand. Instead, use a piece of cardboard to check for leaks.-Do not use unit if exterior hose damage is evident. Make sure all fittings are tight before starting. Relieve system pressure before servicing.-Know how to stop engine and bleed pressures quickly. Be thoroughly familiar with the controls.-Make sure accessories meet the unit's temperature and pressure limits.-Stop engine, bleed pressure, and engage spray gun safety lock before leaving unit unattended.3.) Risk of fire and explosion.Hot exhaust fumes from engine can cause fire. Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel.-Position muffler at least 7 feet from combustible objects.-Before adding fuel, stop the engine and keep heat, sparks, and flame away. Do not add fuel when engine is running or still hot. No smoking near engine.-Do not pump fuel directly into engine at gas station. Static charge can build and ignite fuel. Use a UL approved fuel container to transfer gas to the engine. Wipe up fuel spills immediately.-Only store and handle fuel outdoors. Gasoline vapors can ignite if they collect inside an enclosure. Explosion can result.-Do not change or add to exhaust system. Fire can result.-Do not change or add fuel tanks or fuel lines. Fire can result.-Before each use, check fuel tank and fuel lines for leaks. Any fuel leak is a fire hazard. Fix any fuel leaks before starting engine.-During transportation take precautions to make sure pressure washer will not tip over and cause a fuel leak fire hazard.4.) Poisonous gas.This machine gives off carbon monoxide, a poisonous gas that can kill you. You CANNOT smell it, see it, or taste it.-ONLY run machine outdoors and away from air intakes.-NEVER run machine inside homes, garages, sheds, or other semi-enclosed spaces. These spaces can trap poisonous gases, EVEN IF you run a fan or open doors and windows.If you start to feel sick, dizzy, or weak while using this machine, shut it off and get to fresh air RIGHT AWAY. See a doctor. You may have carbon monoxide poisoning.Save These InstructionsPump Oil Cap and Pump Component IdentificationModel Time to fill 5 gallon bucketsecondsA1577541 100secondsA1573981 84secondsA1573981 58A1578111 100secondssecondsA1578131 84secondsA1578151 72secondsA1578171 100secondsA1578173 100secondsA1578181 84A1578201 72secondssecondsA1578203 723.) The water supply garden hose must have an inside diameter of at least 5/8”. If the hose is morethan 100 ft. long, the diameter must be at least 3/4”.4.) Never use a reservoir tank as a water source. Drawing water out of a tank may cause pumpcavitation and damage to your pump. This pressure washer is designed for a pressurized water source such as a city water faucet. However, the water source pressure must not exceed 115 psi(8 bar).5.) Always use a flexible rubber hose for your water supply. Do not use rigid piping.6. Insert nozzle.7. Start engine.Shut-Down Instructions1. Turn engine OFF.2. Turn water supply OFF.3. Squeeze trigger to relieve system pressure.4. Remove garden hose.5. Remove pressure hose.5.) Apply chemicals evenly onto the cleaning surface. Allow the chemicals to react with the dirt, then5.) Unplug spark plug wire from spark plug, (see engine owners’ manual).Maintenance ScheduleWhat to Check When To Check What to Do Inlet Filter Each Use Visually inspect and clean inlet filter with clear water.Pressure Hose Each Use Visually inspect pressure hose and hose couplings. Replace hose if any of the following is evident:hose coupling is damaged, wire mesh is exposed or damaged, hose is permanently kinked or flattened, outer hose cover is blistered or loose.Bolts Each Use Tighten any loose bolts.Engine Oil See engine manual See engine manual for oil change instructionsPump Oil After 1st 50hrs,then 3mo/500hr Change pump oil. See pump oil change instructions on next page.4.) With the pump in a level position, fill to the half way point on the oil sight glass (see pump oil capacitiesbelow). For Comet or NorthStar pumps use Universal Tractor Transmission Oil or Mobil1 synthetic oil (15W50). For Cat pumps use SAE30 non-detergent oil or Cat Pump Oil Item# 22158.Protect your pump, hose, and gun from freezing.Items needed: 12” piece of garden hose or equivalent, funnel and RV antifreeze (approximately 6 oz.)1.) Follow the storage instructions listed above.2.) Disconnect spark plug cable. Make sure the engine start switch is OFF, and the fuel valve is OFF.3.) Attach the garden hose with funnel to the pump inlet (see illustration).4.) Pour RV antifreeze into the funnel, pull the engine recoil until antifreeze comes out the pump outlet.5.) Drain all water from the high pressure hose. Depress trigger on gun and drain all water out ofTroubleshootingProblemEngine will not start SOLUTION: A,BLow/Surging pressure or no water flow SOLUTION: C,D,E,F,G,HNo chemical injection SOLUTION: I,J,K,LCause Solution A- Low oil shutdown See engine manual for oil requirementsB- Engine starting instructions not followed See engine manual for starting instructionsC- Insufficient water supply See water supply section of this manualD- Plugged pump inlet filter See maintenance section of this manualE- Wrong nozzle Make sure high pressure nozzle is being usedF- Plugged nozzle Remove nozzle, check for blockageG- Worn nozzle Replace nozzleH- Leak in pressure hose Replace pressure hoseI- Wrong nozzle Make sure chemical nozzle is being usedJ- Back pressure from extra long discharge hose Try shorter hoseK- Leak in chemical siphon hose Replace hose – use hose clamps if necessaryL- Chemical strainer not submerged Make sure strainer is completely submergedAny Questions, Comments, Problems or Parts OrdersCall Northstar Product Support 1-800-270-0810SpecificationsA1577541 A1573701PSI 2000 PSI 2700GPM 3.0 GPM 2.5Max Water Temp 140°F Max Water Temp 140°FPower 5-6.5hp Gas engine Power 5-6.5 hp Gas engineShaft size ¾” keyed Shaft size ¾” keyedNozzle size #3.0 Nozzle size #4.0A1573981 A1578111PSI 3000 PSI 2700GPM 4.0 GPM 2.5Max Water Temp 140°F Max Water Temp 140°FPower 11-13 hp Gas engine Power 5-6.5hp Gas engineShaft size 1” keyed Shaft size ¾” keyedNozzle size #4.5 Nozzle size #3.0A1578171 A1578131PSI 2750 PSI 3000GPM 2.5 GPM 3.0Max Water Temp 140°F Max Water Temp 140°FPower 5-6.5hp Gas engine Power 8-9hp Gas engineShaft size ¾” keyed Shaft size 1” keyedNozzle size #3.0 Nozzle size #3.5A1578181 A1578151PSI 3200 PSI 4000GPM 3.0 GPM 3.5Max Water Temp 140°F Max Water Temp 140°FPower 8-9hp Gas engine Power 11-13hp Gas engineShaft size 1” keyed Shaft size 1” keyedNozzle size #3.5 Nozzle size #3.5A1578201 A1578173PSI 4000 PSI 3000GPM 3.5 GPM 2.5Max Water Temp 140°F Max Water Temp 140°FPower 11-13hp Gas engine Power 5-6.5hp Gas engineShaft size 1” keyed Shaft size ¾” keyedNozzle size #3.5 Nozzle size #3.0A1578203PSI 4000GPM 3.5Max Water Temp 140°FPower 11-13hp Gas engineShaft size 1” keyedNozzle size #3.5The manufacturer reserves the right to make improvements in design and/or changes inspecifications at any time without incurring any obligation to install them on units previouslysold.Parts Explosion Rev. F.2Item Part# DescriptionQty Model 1 77982735811 35812 779828 38518 779829 777654 778164 38520 781210 781209 Comet VRX Pump General TP 2530 General EZ3040 Comet BXD Pump Cat 3DX Pump Comet AXD Pump Cat 3SP Pump Comet ZWD Pump Cat 66DX Pump NorthStar NSLW NorthStar NSZW 1 11 11 11 1 1 1 1 A1577541 A1573701 A1573981 A1578111 A1578171 A1578131 A1578181 A1578151 A1578201 A1578173 A15782032 777915 Quick ConnectOutlet Plug 1 all 3 402738596 35169 Inlet Filter Inlet Filter Inlet Filter1 1A1577541, 3701, 3981,8111,8131, 8151,8173,8203 A1578171,818 A1578201 4 777340 ¼” x ¼” Hose BarbFitting1 A1578171,8181, 8201 5 777834 ¼” Hose Clamp2 A1578171,8181,8201Item Part# DescriptionQty Model6 777165 ¼” PVC Hose 14” A1578171,8181,82017 38584 Easy Start Valve 1 A1578171,8181,82018 777347 3/8” Street Tee 1 A1578171,818182019 35918 777836 Thermal Valve Thermal Valve 11A1578171,8181 A1578201,3701,3981 10 22393 35814 782121 Pop Off Valve Pop Off ValvePop Off Valve111A1578181,8201 A1573701 A1573981 18 35813 Manifold Inlet1 A1573701,398119 82141 82142 82143 3/16” x 1.5” Shaft Key 3/16” x 2” Shaft Key ¼” x 1 ¾” Shaft key 111A1578171 A1573701 A1578181,8131,3981,8151,8201 20 777165 ¼” Chemical Hose3ft all 21 221222 Chemical Strainer1 all 22 777837 3/8” plug1 A1578181。
高压清洗机安全使用说明说明书
高压清洗机安全使用说明尊敬的用户：感谢您选用本系列清洗机。
在您使用本机前，请详细阅读本使用说明书，严格遵守安全规程，以防发生意外事故和造成不必要的损失。
希望您能够安全、合理、高效地使用机具。
本产品的“三包”服务和维修可与您所在地区的特约经销单位或本公司品质部联系。
由于产品不断改进，本说明书图样与参数若与产品稍有出入，恕不另行通知。
一、结构简介二、适用范围三、主要技术参数四、结构特点五、安全事项六、工作原理七、使用说明八、注意事项九、保养十、保修细则十一、故障排除表z1、多种机动车辆、工程车辆、工程机械和农业机械配套产品的清洗保养，如冲洗汽车、推土机、混泥土搅拌机、拖拉机等。
是个人和单位及商业性养护货车、轿车、摩托车等最为理想的清洗工具。
1、本清洗机选用专用电动机，通过斜面轴承驱动三缸柱塞泵，结构紧凑、性能可靠、体积小、重量轻、外壳采用全塑料结构，确保永无生锈腐蚀，既安全又美观且适用。
2、低保压功能更有效的增加机器使用寿命和安全使用性能3、用户可根据需要选用混药器以提高清洗效果。
当你在使用混药器时，应将喷头转换到喷淋的位置（该喷嘴为本公司的多功能喷头），如果你在使用药混器时选错了喷头功能，则无法自动吸混药液。
4、本公司清洗机目前形式上可分为旅行箱式移动方式和壁挂式两种，旅行箱式移动轻巧轻松，可单手提、拉；壁挂式可固定在墙壁上从而有效的节省地面工作空间利用空间。
1、在使用前必须仔细阅读此使用说明书，高压清洗机不能让儿童或没有经过培训的人员使用，不应在没有穿专业防护服的人群中使用本清洗机。
2、在进行清洗作业时，应采取正确的姿态紧握喷枪手柄，扣动扳机时要注意水喷出时会产生一定的反冲力和对手柄的扭转力矩，操作时一定要做到注意力集中避免意外发生。
3、严禁把喷枪头对准或朝向人、动物或带电设施，否则会造成严重损伤或伤亡事故。
高压喷头若使用不当会有危险，喷头严禁直接对着自己、他人、带电设备设施和清洗机本身喷射4、为了避免电缆损坏而发生漏电危险，请不要把清洗机的电源线至于路口、热源或有尖锐棱角的物料附近。
高洁清洁设备有限公司 高压清洗机 使用说明书
东莞市高洁清洁设备有限公司 １５６ ２２９３ ２５７２官网：ｗｗｗ．ｄｇｋａｒｃｈｅｒ．ｃｏｍ在您第一次使用您的设备前，请先阅读并遵守本操作说明书原件，为日后使用或其他所有者使用方便请妥善保管本说明书。
- 首次启动之前，必须通读使用说明与安全提示Nr.5.951-949!- 如果本装置在运输途中受损，则应及时通知供应商。
- 开箱之前，应检查包装内含物。
目录环保ZH . . 1使用说明书中的符号ZH . . 1概述ZH . . 2机器上的符号ZH . . 2正确使用ZH . ..2安全说明ZH . . 3安全装置ZH . . 3启动ZH . ..3操作ZH . .5存放ZH . . 7运输ZH . ..7保养与维护ZH . ..8排除故障ZH ..8质保ZH . 10附件与备件ZH . 11EC 一致性声明ZH . 11技术规格ZH . 12环保包装材料可以回收利用。
请不要将包装材料与普通材料放在一起处理；而应妥善安排回收。
旧的设备中含有宝贵的可再利用的材料；应加以回收利用。
电池、油以及类似物质不可以进入自然环境。
请通过适当的收集系统处理您的旧设备。
切勿向环境释放发动机油、燃油、柴油和石油。
保护地面，采用环保方式处置废油。
内部材料提示（REACH ）最新的内部材料信息请您在如下链接中查找：/REACH危险可以导致严重伤害甚至死亡的危险。
警告可能的危险情形，可导致严重伤害甚至死亡。
小心可能的危险情形，可导致人身中度伤害或财产损害。
概述 装置元件图11 防护盖2 喷杆支架（两侧）3 软水剂 RM 110/RM 1114 带制动器的转向滚轮5 运输安装位置（两侧）6 高压软管7 手持喷枪8 喷杆9 高压喷嘴（不锈钢） 10 电源11 手持喷枪安全销12 手持喷枪压力/流量调节器 13 带过滤器的水源接头 14 高压接头 15 台阶踏板 16 清洁剂箱2 17 清洁剂箱1 18 储物箱 19 手柄 20 操作区21 储存室闭合挡板 22 附件储存室 23 铭牌 24 盖锁 25 加油口26 泵压力/流量调节装置 27 放油螺钉28 清洁剂入口止回阀29 含过滤器的清洁剂抽吸管1 30 含过滤器的清洁剂抽吸管2 31 维护开关 32 低水位保护 33 加热器34 过滤器（水） 35加热器放水螺钉操作区图2A 主开关B 温度控制旋钮C 清洁剂剂量旋钮D 压力计 1 泵指示灯2 “低水位”指示灯3 “待机”指示灯4 加热指示灯5 电机指示灯6 加热器故障指示灯7 维护指示灯8 软水剂指示灯高压喷射如果适用不当，则很危险。
高压清洗机操作说明书
KJ-1590 高压清洗机操作说明书
1. 如果喷嘴不能通过管道里的障碍，就要把脉冲 模式和手动调节结合起来。
2. 一旦通过了障碍，就要使喷嘴来回伸缩几次（建 议关闭脉冲模式），以确保管道完全清理干净。 然后在收回软管之前使它继续前进几英尺。
D. 清洁管道： 高压清洗机清洁管道是通过高压水从喷嘴的孔里 喷到管道内壁上来清洁管道。（同样，高压产生的 推力可以促使喷嘴在管道内前进。）慢慢收回软管 会得到较好的清洗效果。 1. 确保脉冲激励器关闭。这可以在喷嘴产生最大
5. 附件：
A. 压力冲洗设备（图 9）。 KJ-1590 可以和压力冲洗设备一起使用，用来清洗 汽车，管道和电缆。 使用压力冲洗设备步骤如下： • 检查脉冲激励器是否置于关闭状态。 • 使用附件中的 1/2” × 10m 的软管或任何 1/2”的
清洗机软管。 • 黑色的喷嘴末端有两档调节。通过旋转喷嘴，
螺纹尺寸 软管尺寸 软管内径 具有三个背面 喷射水流特征 的喷嘴可以产 生最大的推力 使软管前进很 长的距离。这种 喷嘴应用最广
KJ-1590 1/8” NPT 1/8” & 1/4” 1/8” & 3/16”
64802(H-81)
KJ-1590 1/4” NPT
1/2” 1/4”
58436
泛。 使用具有三个 背面喷射孔的 喷嘴再加前部 有一个喷孔，可 以穿透硬的油 脂和软泥障碍。 前部的孔可以 在障碍上打出 一个小孔，使喷 嘴通过。对冰特 别有效。 使用下垂式喷 嘴可以容易通 过困难的弯头。 它也有三个背 面喷孔。
A． 进水过滤器窗口。 使用之前：检查进水过滤器窗口，看是否有碎片堵 塞，否则会限制水流进泵里导致机器工作效果变 差。如果窗口变脏或堵住了，拆下来清洗并更换。 B． 喷嘴孔 在使用之前：检查喷嘴孔是否堵住了，如果堵了， 用喷嘴孔清洗工具清理堵塞物。 C． 冲洗 使用之前：用干净的水冲洗清洗机和软管内的碎 片。确保喷嘴从软管上拆下来以使水流最大。 D． 马达用油 确保使用 SAE 90, 0.22 升。不要加太多的油，因为 压力达不到。在第一次使用 50 小时后，必须换油。 之后，每 200 小时或至少 1 年换油一次。 油帽可以防止油从马达里漏出来。但是当机器翻过 来，可以允许少量油漏出来。
超爵高压洗车机说明书
超爵高压洗车机说明书
1、请勿使用非中性清洗剂放入机器内，或操作不当而造成机器堵塞或破坏性损坏。
2、使用本设备前一定要先检查设备电源线、压力调节开关、面板是否有破损、积水现象，如有以上情况禁止使用设备。
3、本设备不可供儿童使用，请勿让儿童触及。
4、不要在疲惫、醉酒和药物作用下操作本设备。
5、操作时将本设备摆放在平稳的平面上，要保持本设备平衡。
6、理解说明书上全部保养及维修知识，本设备为专业产品，在没有经过厂家的专业技术员允许，不可自行将主机打开或拆卸，否则可能造成不良后果。
7、工作中请注意不要淋湿本设备主机面板，避免发生触电危险，万一主机面板被淋湿，请立即停止工作，拔下电源插头，用百洁布擦干主机面板，并让其自然风干后才可继续使用。
8、操作时不可将本设备对人，宠物，机器本身喷射，以免发生意外。
9、每次使用完毕，务必先将主机内部用干净的清水过滤排干后，再将电源切断关机，保证设备主机面板整洁干净。
ABW-VBP-110P高压清洁机操作说明说明书
ABW-VBP-110PHigh Pressure CleanerOperating InstructionsOriginal instructionsWARNING: Do not use the machine w ithout reading the instruction sheet.NAME S OF E XTE RIOR PARTSAPPLICATIONTHE POR TABLE PR ESSURE WASHING MACHINE is a highly specialized multif unctional machine with exceptionally reliable saf ety assurance, which may be used to wash and clean cars, bikes and other outdoor equipment or garden patios, green houses etc.Helpful Hints for Getting StartedAutomatic ON/OFF:The motor on this pressure washer does not run continuously. It only runs when the trigger of the spray gun is squeezed. Af ter f ollowing the start up procedures in this manual, turn the pressure washer ON and squeeze the trigger f or activ ation. See “Operating Instruction” section in this manual f or f urther details.WARNING! The electrical supply connection shall be made by a qualif ied person and comply with IEC 60364-1. The electric supply to this machine should include either a residual current dev ice that will interrupt the supply if the leakage current to earth exceeds 30 mA f or 30 ms or a dev ice that will prov e the earth circuit.WARNING! The operating method to be f ollowed in the ev ent of accident (e.g. contact with detergents: rinse with an abundance of clean water) or breakdown to prev ent unsaf e situations.WARNING!The motor of this pressure washer will NOT run unless the trigger is squeezed.Safety GuidelinesThis manual contains inf ormation that is v ery important to know and understand.This inf ormation is prov ided f or SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this inf ormation, observ e the f ollowing sy mbols.DANGER!Danger indicates an imminently hazardous situation w hich, if not avoided, WILL result in death or serious injury.WARNING!Warning indicates a potentially hazardous situation w hich, if not avoided, COULD result in death or serious injury.CAUTION:Caution indicates a potentially hazardous situation w hich, if not avoided, MAY result in minor or moderate injury.NOTE: Inf ormation that requires special attention.Important Safety Instructions SA VE THESE INSTRUCTIONSWARNING! When the machine is used, f ollowing precautions should alway s be considered:1. Read all instructions bef ore using the machine.2. To reduce the risk of injury, close superv ision is necessary when a machine is used near children.3. ALWAYS disconnect power bef ore disassembling or repairing the unit of the machine.4. Follow all saf ety codes as well as the Occupational Saf ety and Health Act(OSHA).5. Ensure saf ety devices are operating properly bef ore using the machine. DO NOT remov e or modif y any part of the gun or unit of the machine.6. Know how to stop this machine and bleed pressure quickly. Be thoroughly f amiliar with the controls.7. Stay alert – watch what y ou are doing.8. Do not operate the machine when f atigued or under the inf luence of alcohol or drugs.9. Keep operation area clear of all persons.10. Do not ov erreach or stand on unstable support. Keep good f ooting and balance at all times.11. Follow the maintenance instructions specif ied in the manual.12. Use cleaning agent supplied or recommend by the manuf acturer.13. Only put the machine on stable place when using, transportation, assembly, dismantling. Do not rough handling the machine when transportation.14. In any ev ent of accident (e.g. contact with detergents, rinse with an abundance ofclean water), please alway s switch off the machine and pull out the plug f rom socket outlet, and Disconnect the connection with water.15. The machine is not intended to be connected to the potable water mains. If necessary, please use only inlet hose-set approv ed by IEC 61770.Risk of injection or severe injury. Keep clear of nozzle. Do notdischarge streams at persons. This machine is to be used only by trained operators. Alw ays remove lance from gun before cleaning debris from tip. • Keep clear of nozzle. NEVER direct high pressure spray at any person, animal or self.• Alway s wear saf ety glasses or goggles and protectiv e clothing when operating orperf orming maintenance.• Nev er put hand or f ingers ov er the spray tip while operating the unit.• Nev er try to stop or def lect leaks with any body part.• Alway s engage the trigger saf ety latch in the saf e position ev en when spray ing is stopped f or a moment.• Alway s f ollow detergent manuf acturer’s label recommendations f or proper use of detergents. Alway s protect ey es, skin, and respiratory sy stem f rom detergent use.WARNING!SE RVICING OF A DOUBLE INSULATED MACHINEIn a double-insulated machine, two sy stems of insulation are prov ided instead of grounding. No grounding means are prov ided f or a double-insulated machine, nor should grounding means be added to the machine. Serv icing a double-insulatedmachine requires extreme care and knowledge of the sy stem, and should be done only by qualif ied serv ice personnel.Replacement pars f or a double-insulated machine must be identical to the originalparts. A double-insulated machine is marked with the words “Double Insulation "or “Double Insulated.” Machine may also be marked with sy mbol shown in Figure 1.WARNING!Do not use pressure that exceeds the operating pressure of any of the parts (hoses, fittings, etc.) in the pressurized system. E nsure all equipments and accessories are rated to w ithstand the maximum w orking pressure of the unit.WARNING!E xplosion hazard. Nev er spray f lammable liquids or use pressure washer in areas containing combustible dust, liquids or v apors.Nev er operate the machine in a closed building or in or near an explosiv e env ironment.WARNING!Do not spray electrical apparatus and w iring.• Nev er disconnect the high pressure discharge hose f rom the machine while the sy stem is pressurized. To depressurize machine, turn power and water supply of f, then press gun trigger 2~3 times.• Nev er permanently engage the trigger mechanism on the gun.• Nev er operate the machine without all components properly connected to the machine (handle, gun/wand assembly, nozzle, etc.).WARNING!E quipment damage.• ALWAYS turn water supply “ON” bef oreturning pressure washer “ON.” Running pump dry causes serious damage.• Do not operate the pressure washer with the inlet water screen remov ed. Keep screen clear of debris and sediment.• NEVER operate pressure washer with broken or missing parts. Check equipment regularly and repair or replace worn or damaged parts immediately.• Use only the nozzle supplied with this machine.•Nev er leav e the wand unattended while the machine is running.•Nev er attempt to alter f actory settings. Altering f actory s ettings could damage the unit and will v oid the warranty.• Alway s hold gun and wand f irmly when starting and operating the machine.• NEVER allow the unit to run with thetrigger released (of f) f or more than one (1) minute. Resulting heat buildup will damage pump.• Pressure washer is not supposed to pump hot water. NEVER connect it to a hot water supply as it will signif icantly reduce the lif e of the pump.• NEVER store the pressure washer outdoors or where it could f reeze. The pump will be seriously damaged.• Release trigger when changing f rom high to low pressure modes. Failure to do so could result in damage.• Be aware of the recoil caused by the water jet when the machine is switched on. CAUTION:Keep hose aw ay from sharp objects. Bursting hoses may cause injury. E xamine hose regularly and replace it if damaged.Do not attempt to mend a damaged hose.E XTENSION CORDSThe use of an extension cord is not recommended. Use only extension cords intended f or outdoor use. These are identif ied by the mark “Acceptable f or use with outdoor machines; store indoors while not in use.” Use only extension cords hav ing an electrical rating equal to or more than the rating of the machine. Do not use damaged extension cords. Examine extension cord bef ore using and replace it if damaged. Do not abuse extension cord. Do not pull on the cord to disconnect. Keep cord away f rom heat and sharp edges.Alway s disconnect cord f rom receptacle bef ore disconnecting machine f romextension cord.DANGER!Failure to f ollow these instructions can result in serious injury, including death.WARNING!To reduce the risk of electrocution, keep all connections dry and of f the ground. Do not touch plug with wet hands.Machines shall not be used by ised to ensure that they do not play with the machineThis machine is not intended f or use by persons (including children) with reduced phy sical, sensory or mental capabilities, or lack of experience and knowledge.WARNING!This machine has been designed f or use with the cleaning agent suppliedor recommended by the manuf acturer. The use of other cleaning agents or chemicals may adv ersely af fect the safety of the machine.WARNING!Recommend the operator to wear ear protectors.WARNING!High pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, liv e electrical equipment or the machine itself.WARNING!Do not use the machine within range of persons unless they wearprotectiv e clothing.WARNING!Do not direct the jet against y ourself or others in order to clean clothes orf oot-wear.WARNING!Risk of explosion-Do not spray f lammable liquids.WARNING! High pressure cleaners shall not be used by children or untrained personnel. WARNING!High pressure hoses, f ittings and couplings are important f or the saf ety of the machine. Use only hosed, f ittings and couplings recommended by the manuf acturer. WARNING! To ensure machine saf ety, use only original spare parts f rom themanuf acturer or approv ed by the manuf acturer.WARNING! Water that has f lown through backf low prev enters is considered to the non-potable.WARNING! The machine shall be disconnected f rom its power source by remov ing the plug f rom the socket-outlet during cleaning or maintenance and when replacing the machine to another f unction.WARNING! Do not use the machine if a supply cord or important parts of the machine are damaged, e.g. saf ety devices, high pressure hoses, trigger gun.WARNING! If an extension cord is used, the plug and socket must be of watertight construction.WARNING! Inadequate extension cords can be dangerous. If an extension cord is used, it shall be suitable f or outdoor use, and the connection has to be kept dry and of f the ground. It is recommended that this is accomplished by means of a cord reel which keeps the socket at least 60mm abov e the ground.WARNING! In order to av oid a hazard due to inadv ertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching dev ice, such as a timer, or connected to a circuit that is regularly switched on and of f by the utility.or connection to the potable water mains.WARNING! The machine is intended to be used at a temperature abov e o degree. (Only f or machine with power cord of H05VV-F).WARNING! To ensure the machine saf ety, please only use original spare parts (including nozzle) f rom the manuf acturer or approv ed by the manuf acturer. Do not use the machine bef ore y ou changed them if they are damaged.WARNING! Be care of the danger of the kickback f orce on the spray assembly when opening the trigger gun and grasp the gun with hands f irmly.WARNING:When the machine is mov ing and installing, the machine must be in f lat. When mov ing the machine, pulling the handle to mov e it.WARNING!Connect to the water supply. The machines are not suitable f or connection to portable water mains. Connect the machine to the water supply. (It can be a water container). Make sure the inlet water pressure keeps between 0.01MPa and 0.4MPa.Do not use the pipe if the pipe is damaged.If y ou want connect this machine to portable water mains, y ou must install a backf lowprev enter in the water pipe to prev ent dirty water f low back to the drinking water sy stem. The backf low prev enter shall comply with EN 60335-2-79 ANNEX AA.WARNING!Disconnect f rom the electrical power supply bef ore carry ing out user maintenance. If the mains cable is damaged it must be replaced by the manuf acturer, orits serv ice agent or similarly qualif ied person to av oid a hazard.Running Instructions! This unit is to be connected to a cold water source ONLY.! The motor of this pressure washer will NOT run. It will only operate when the trigger is squeezed.- Connect the outlet hose to the washer and connect the spray gun to t he outlet hose.- Connect nozzle and nozzle extension.- Check gauze f ilter is clear of any blockage.- Connect the water supply hose.- Check that the hose has no kinks in it- Turn on water and check f or leaks.- Depress trigger to allow air to be expelled though the pump and hoses, lock trigger.- Plug in machine and turn on side switch.- Unlock trigger and use the pressure washer.Shut down1. Turn of f the motor(push switch to the of f position).2. Unplug the unit f rom the power source.3. Turn of f the water supply.4. Press the trigger of the gun to depressurize the sy stem, take down the water outlethose, 10 seconds racing of the motor to let take water completely spray out.5. Disconnect the garden hose f rom the pressure washer.6. Wipe all surf aces of the unit with a damp clean cloth.7. Engage the gun saf ety lock.CA UTION: ALWAYS turn of f the unit’s motor BEFORE turning of f the unit’s water supply.Serious damage could occur to the motor if the unit is run without water.CA UTION: NEVER disconnect the high-pressure discharge hose f rom the machine whilethe sy stem is still pressurized. To depressurize the unit, turn of f the motor, turn of f thewater supply and squeeze the trigger 2-3times.Spray NozzleThe Pressure Washer comes f urnished with f our spray nozzles. Each nozzle is colorcoded and deliv ers a specif ic spray pattern and pressure f or a particular cleaning job. Thesize of the nozzle determines the size of the f an spray and the pressure out of the nozzle.25° Nozzle – Green: This nozzle deliv ers a 25 degree spray pattern f or intense cleaning oflarger areas. This nozzle should only be used on areas that can withstand pressure f romthis nozzle. (f ig 1)Chemical Nozzle – Black: This nozzle is used to apply special chemicals and cleaningsolutions. This nozzle produces the weakest pressure stream of the f iv e nozzles. (f ig 2)Turbo Nozzle:This nozzle circulates a powerf ul spray into a circular pattern to prov idegreater cleaning ef f iciency over large areas. ( f ig 3)The nozzles are stored in receptacles on a panel mounted to the handle of the washer.Colors on the panel identif y nozzle location and spray panel.Fig 1 Fig2 Fig 3 Fig 4 WA TER INLET SCREENThe water inlet f ilter must be inspected regularly, so as to av oid blockage and restriction inthe water supply to the pumpUSING DETERGENTAdd detergent to the container. Set the Adjustable Spray Wand at low pressure posit ion. Trigger gun to spray detergent.GUN SAFE TY DE VICEWhenev er y ou use the high pressure washer, we suggest y ou grip the in the right position, with one hand on the handle and the other on the lance, When y ou stop the machine it is necessary to use the saf ety lock placed on the gun in order to av oid accidental.CLE ANING PIN INSTRUCTION• Using included tip cleaner, or an unf olded paper clip, insert wire into the nozzle holeand mov e back and f orth until debris is dislodged.• Remov e additional debris by back-f lushing water through the nozzle. To do this, place end of a garden hose ( with water running ) to the end of nozzle f or 30-60 seconds.MAJOR TE CHNICAL DATAE LE CTRICAL DIAGRAMPOSSIBLE PROBLE M AND SOLUTIONINSTALLATION, E LE CTRICAL AND WATE R CONNE CTIONS1. .PRESSURE CLEANER2. WATER SUPPLY HOSE （not include）4. WATER INLET3. WATER CONNECTION（not include）5. HIGH PRESSURE TUBE6. HIGH-P R ES S U R E, WATE R OUTLE T7. SPRAY GUN 8. F.E.M LINE（not include）Note： The company reserves the right to modify its machine specifications without given any notice; for up to date information please visit our website.INSPE CTION & MAINTE NANCEFor saf ety use, make sure ev ery three-months y ou clean the machine. Bef ore working, make sure inspect the f ilter and the nozzle, make sure there is no impurity. Af t er working, make sure there is no water in the pump and the hose.If the machine need to be repaired in the guarantee period, please return the machine to the shop. You need to prov ide the certif icate of purchase in order to repair or get the substitute.Bef ore Packaging, The machine should be cleaned, then use closed packaging, packaging should be f irm. Store the machine in dry conditions.For transportation saf ety. The machine should comply with ISTA.。
富森冷水高压清洗机FS1535使用说明书
FS 15/35冷水高压清洗机使用说明书一FUSSEN系列高压清洗机1. 您所购买的高压冷水清洗机是由具有领先技术水平的制造商设计的。
2. 为了要确保产品的使用寿命和较高的耐久性, 我们建议您在操作设备之前仔细阅读这本操作手册。
3. 本操作手册提供给：操作者、维护技术人员和修理技术人员。
4. 随着我司不断对产品研发, 本使用指南内容与资料日后如有所更新将不另行通知。
二高压冷水清洗机1. FUSSEN 系列高压冷水清洗机，可使您在更短的时间内达到最佳清洗效果。
2. FUSSEN提供了您高效率主机及配件来满足您对繁重及严峻考验的清洗工作要求。
主机的构造,设计与其经过喷塑处理的钢框架使您的高压清洗机在运输和使用中受到最佳保护，以上的结合帮助您解决高压清洗工作中的一切问题。
高压冷水清洗机系列是根据清洗工作繁重及环境考验程度而设计的。
所有的泵和所有与水接触的部件均由抗腐蚀的材料组成，陶瓷活塞，长寿命的密封和不锈钢阀，它们一起确保了水枪的长寿命和耐久性。
三技术参数类型参数型号FS 15/35最大压力（巴/兆帕/PSI）0-350/0-35/0-5075最大流量（升/小时）900驱动（伏特/相/赫兹）400/3/50功率（千瓦）11最大进水温度（摄氏度）60最小进水流量（升/分钟）32转速（转/分钟）1450重量（公斤）180尺寸（长宽高毫米）1150×800×800四高压冷水清洗机的用途能够除去清洗车辆、机械、船舶、建筑物上附着的任何类型的污垢：1. 水泥/混凝土2. 表面附着物/表面处理3. 去除油漆和锈4. 去除凝结的污垢5. 使用选用配件能进行更多的处理工作：5.1喷砂5.2下水道的清洁五安全预防1. 为防止意外事件发生而且确保操作人、旁观者以及周围机械安全，应在附近放置一些警示牌或采取安全防范措施。
把机器视为一个高速切削的工具。
2. 请不要让孩子、行为障碍人士或没有阅读安全操作手册的人操作机器。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
高压清洗机说明书
型号:TVE070C、TVF070C TVB080G、TVD100C
TVG100C
使用本机之前，请先阅读说明书
适用范围
我们的高压清洗机是专业化，多功能又有可靠的安全保障的机器。
适用于汽车、自行车、户外设备、花园和温室等的清洗。
安全手则
警告：使用本产品前，请先阅读说明书。
警告：为减少受伤风险，当靠近儿童操作时，应严格看管本机。
未经训练的人员和儿童不得操作本机。
警告：应了解快速开关机，并熟悉本机全部功能。
警告：操作时，应保持警惕和看管好本机。
警告：不要在疲惫、醉酒和药物作用下，操作本机。
警告：保持操作区无其他人。
警告：不要将本机延伸过远，或摆放在不牢固的支撑上，要保持本机平衡。
警告：理解说明书上的全部保养及维修知识。
警告：本新产品提供接地故障电路断流器在电源插头处，如果需要替换电源线及插头请使用相同的部件。
警告：本产品必需接地。
当本机在出现故障或损坏而漏电时，接地可以防止触电事故发生。
插头必须插在合适的插座并插紧，应用的额定电压必须与
当地的供应电压相一致。
警告：如果你对是否适合接地有疑问，请找有资格的电工或服务人员检验。
不要修改已供给的电源插头，如果插座不适合，请找有资格的电工安装插
座。
不能用任何改造的电源插头用于本机。
警告：当用于室外操作时，插座必须是防水结构，延长线必须有室外使用的认证标志，不用时存放在室内。
本机供应电流应不少于额定电流。
使用前，请先检查延长电线，如果已损坏，请更换。
使用不适合的外延电线会有
很大的危险。
不要滥用延长电线，拔插头时请不要猛拉电线。
延长电线
远离热源及锋利刀口。
分离本机时，请先将插头从插座处分离。
警告：如果供给电线已损坏，必须使用专用的电线，也可让销售商或生产厂家重新装配。
警告：为了减少触电风险，在下雨和雷雨天气不要开启和操作本机。
保持所有接口干燥，并脱离地面，不要用湿手触摸插头，严禁水渗透本机。
警告：本机运行时，必须保持持续的供水，没有水循环温度将会达到危险点，会引起机内密封圈的损坏。
警告：不要使用本机用于特别寒冷处，以防止冰冻而损坏本机。
警告：此机设备只为清洁水设计，不能使用腐蚀性的化学液体。
警告：不能将本机直接对准人体、宠物及机器本身喷射。
警告：在维修保养时，必须切断电源。
警告：为了确保实用安全，请用最初的备用配件及生产商指定的配件。
假如机器损坏，没有修复以前请不要使用本机。
操作指南
－连接软管到出水口，并连接喷抢到软管另一头。
－连接喷头和喷杆。
－查看过滤网是否有障碍物。
－连接供水软管。
－检查是否连接好。
－喷出水试一下，检查是否漏水。
－压下板机，通过抽水机和软管去除空气，然后锁上板机。
－插上本机电源，按“O”开启开关。
－解开枪锁，使用高压清洗机。
可调节喷头
水可以从喷头喷出直线（图1）或扇形（图2），首先开启压力机然后调整喷头。
用手旋转塑圈
进水口网筛
进水口过滤网要定时检查，以避免阻塞而限制抽水机供水（图3）
长期保存
本机应存放在无霜冻的环境
长时期不使用机器，可能形成水垢使机器很难开启。
在这种情况下，应关掉本机，用手旋转电机数圈，以避免电流过大，致使开关损坏（图4）。
主要技术数据
维修保养
安装连接图
１主机２供水软管３水管接合配件
４进水口５高压管６自来水龙头
７喷枪８电源插头
注意：假如产品更新，公司将保留没有预先通知的情况下，
修改说明书的权利。
[此文档可自行编辑修改，如有侵权请告知删除，感谢您的支持，我们会努力把内容做得更好]。