CP45错误信息中英文对照表

Failed to lower the BUT. Failed to advance the Edge Fix. 贴片机错误信息中英文对照表 Failed to step back the Edge Fix. HOLE_FIX_UP_ERROR HOLE_FIX_DOWN_ERROR Sensor of Hole Fix is not detected. Rightward sensor of Hole Fix cannot be detected. Leftward sensor of Hole Fix cannot be detected. Edge Fix cannot be advanced. Edge Fix cannot be stepped back. Error detected in adjusting conveyor width. PCB detected in conveyor area. PCB detected in PCB-in sensor area. PCB detected in PCB-wait sensor area. PCB detected in PCB-work sensor area. PCB detected in PCB-out sensor area. Two PCBs detected in the input buffer. PCBs detected in the input buffer or the wait buffer. PCB detected in the placement buffer. PCB detected in the transmission buffer. PCB-in sensor is NOT normal. PCB-wait sensor is NOT normal. PCB-work sensor is NOT normal. PCB-out sensor is NOT normal. PCB-work-out sensor is NOT normal. PCB did not arrived at the wait sensor area. PCB did not arrived at the work sensor area. PCB did not arrived at the out sensor area. Error occurred in transmitting a PCB. Failed to move PCB in the wait sensor area. Failed to move PCB in the placement sensor area. Failed to move PCB in the transmission sensor area. Wait Stopper cannot be raised. Wait Stopper cannot be lowered. Work Stopper cannot be raised. Work Stopper cannot be lowered. Out Stopper cannot be raised. Out Stopper cannot be lowered. AREA_PCB_OVER_MAXIMUM_WARNING MOUNTING_OVER_MAXIMUM_WARNING SMEMA_SIGNAL_TIMEOUT_ERROR
Manual placement is not allowed while the vaccum is on.
反方向硬限位在$A 轴被检测。 正方向硬限位在$A 轴被检测。 警报发生在 $A轴。 那$A一个桥无法在被叙述的时间期间内停止。 一个错误被发现在那 $一个桥。 1/18 编码器错误在运送装置- 宽度调整桥中发现。 BUT上升失败
Mirror Safety Sensor Error. VME Module Ver %d started. PCB Download Start <$W> PCB Download End Vision Module Ver %d started. Auto Run Start Auto Run Stop Auto Run Pause Auto Run Reset Auto Dump All Report Feed Change Request $A axis motion is interfered by another axis. Error occurred while a motion to move to a safe position was taking. A motion for $A axis is interfered by another axis. In a manual operation, %d axis motion is interfered by %d axis. In a manual operation, %d axis or %d axis motion is interfered by %d axis. Unable to activate feeders because of the unsecured Z axis position. Safety-speed is NOT normal. Manual placement is not allowed while the vaccum is on. H/W Limit in the negative direction was detected in $A axis. H/W Limit in the positive direction was detected in $A axis. ALARM occurred in $A axis. The $A axis failed to stop in a specified time duration. An error was detected in the $A axis. Encoder error detected in the conveyor-width adjusting axis. Failed to lift the BUT.
紧急开关被按下。 前面的紧急开关被按下 后面的紧急开关被按下。 马达开关示教盒被按下。 输入／输出电源开关关掉 。 输入／输出电源开关不能够打开。 JogBox有在～之前桥提议被分离。 前面喂料器感应器被感应。 后面喂料器感应器被感应。 前门是开着的。 后面门是开着的。 当XY gantry的位置不被固定的时候,前面手推车被释放。 前面手推车为手推车释放在被不许的州时候被释放。 当 XY gantry 的位置不被固定的时候 , 后面手推车被释放。 后面手推车在手推车释放的被不许的状态时候被释放。 MIRROR安全感应器错误。 VME 组件 Ver%d 开始。 PCB 数据装载开始 <$W> PCB 数据装载结束 视觉组件 Ver%d 开始。 自动运行开始 自动运行停止 自动运行中止 自动运行复位 自动废料所有记录 喂料器更改需求 $A轴运动时被其它轴。 错误发生在一个动作移动到一个安全的位置正在拿。 一个提议为 $A一个桥被另外的一个桥妨碍。 在手动操作时,%d 轴运动时被%d 轴Fra Baidu bibliotek断。 在人工的操作方面,%d 桥或 %d 桥提议被妨碍被 %d 桥。 不能因为unsecured Z 桥位置刺激饲养者。 安全-速度不是正常。
$2,002 $2,101 $2,102 $2,201 $2,202 $2,210 $2,211 $2,212 $2,301 $2,302 $2,400 $3,000 $3,001 $3,002 $3,003 $3,004 $3,010 $3,021 $3,022 $3,023 $3,031 $3,032 $3,033 $3,034 $3,035 $3,101 $3,102 $3,103 $3,104 $3,201 $3,202 $3,203 $3,301 $3,302 $3,401 $3,402 $3,501 $3,502 $3,600 $3,601 $3,700
2/18
$3,701 $3fff $4,000 $4,001 $4,002 $4,004 $4,005 $4,110 $4,111 $4,112 $4,113 $4,115 $4,116 $4,117 $4,200 $4,201 $4,202 $4,300 $4,301 $4,400 $4,401 $5,000 $5,001 $5,002 $5,003 $5,011 $5,012 $5,021 $5,022 $5,023 $5,024 $5,100 $5,101 $5,200 $5,201 $5,300 $5,301 $5,302 $5,303 $5,304 $5,307
BUT下降失败。 边定位无法夹紧 边定位松开失败。 孔定位上部感应器感应错误 孔定位下部感应器感应错误 孔定位感应器没被检测到 右上方孔定位感应器不能检测到 左上方孔定位感应器不能检测到 边定位不能升级 Edge Fix cannot be stepped back. 错误信号被检测在轨道宽度调节中 PCB被检测在传送区域 PCB被检测在入口感应处 PCB被检测在等待感应处 PCB被检测在贴装感应处 PCB被检测在出口感应处 2块PCB被检测在缓冲信号时 所有PCB被检测在缓冲信号输入或等待时 PCB被检测在贴装缓冲信号 PCB被检测在缓冲信号传输中 PCB-入口感应处是不正常的 PCB-等待感应处是不正常的 PCB-贴装感应处是不正常的 PCB-出口感应处是不正常的 PCB-贴装-出口感应处是不正常的 PCB没有被感应到在等待感应器处 PCB没有被感应到在贴装感应器处 PCB没有被感应到在出口感应器处 错误产生在PCB传输中 PCB不能传送在等待感应区 PCB不能传送在贴装感应区 PCB不能传送在传输感应区 等待止挡器不能上升 等待止挡器不能下降 贴装止挡器不能上升 贴装止挡器不能下降 出口止挡器不能上升 出口止挡器不能下降 PCB范围超值报敬 贴装范围超出最大值报警 连机信号延时报警
Emergency switch is pressed. Front emergency switch is pressed. 贴片机错误信息中英文对照表 Rear emergency switch is pressed. Motor free switch on a teaching box is pressed. I/O power switch is turned off. I/O power switch cannot be turned on. JogBox has been disconnected in presence of axis motion. Front feeder float sensor activated. Rear feeder float sensor activated. Front door is open. Rear door is open.
Front cart was released while the location of the XY gantry was NOT secured. Front cart was released during the disallowed state for the cart releasing. Rear cart was released while the location of the XY gantry was NOT secured. Rear cart was released during the disallowed state of the cart releasing.
$1 $2 $3 $4 $6 $7 $8 $10 $11 $20 $21 $30 $31 $32 $33 $40 $100 $102 $103 $104 $110 $111 $112 $113 $114 $120 $800 $801 $802 $803 $804 $805 $806 $807 $1,000 $1,001 $1,002 $1,003 $1,004 $2,000 $2,001