毛概试2011年真题预测题(93%的真题啊)
TURCK 非锥形感应器 NI3-EG08K-Y1-H1341 说明书
N I 3-E G 08K -Y 1-H 1341 | 11/29/2022 05-07 | t e c h n i c a l c h a n g e s r e s e r v e dNI3-EG08K-Y1-H1341Inductive SensorTechnical dataNI3-EG08K-Y1-H134******** Rated switching distance 3 mmNon-flush Secured operating distance ≤ (0.81 × Sn) mmSt37 = 1; Al = 0.3; stainless steel = 0.7; Ms = 0.4≤ 2 % of full scale ≤ ±10 %1…10 %2-wire, NAMUR 5 kHz Nom. 8.2 VDC Non-actuated current consumption ≥ 2.1 mA Actuated current consumption ≤ 1.2 mAKEMA 02 ATEX 1090X )/inductance (L i )150 nF/150 µHÉ II 1 G Ex ia IIC T6 Ga/II 1 D Ex ia IIIC T135 °C Da(max. U i = 20 V, I i = 60 mA, PThreaded barrel, M8 × 139 mmFeatures■Threaded barrel, M8 x 1■Stainless steel, 1.4427 SO ■DC 2-wire, nom. 8.2 VDC■Output acc. to DIN EN 60947-5-6 (NAMUR)■M12 x 1 male connector■ATEX category II 1 G, Ex zone 0■ATEX category II 1 D, Ex zone 20■SIL2 (Low Demand Mode) acc. to IEC 61508,PL c acc. to ISO 13849-1 at HFT0■SIL3 (All Demand Mode) acc. to IEC 61508,PL e acc. to ISO 13849-1 with redundant configuration HFT1Wiring diagramFunctional principleInductive sensors detect metal objectscontactless and wear-free. For this, they use a high-frequency electromagnetic AC field that interacts with the target. Inductive sensors generate this field via an RLC circuit with a ferrite coil.Technical dataMounting instructionsMounting instructions/Description222/92/11|1431H-1Y-K8GE-3INN I 3-E G 08K -Y 1-H 1341 | 11/29/2022 05-07 | t e c h n i c a l c h a n g e s r e s e r v e d AccessoriesBST-08B6947210Mounting clamp for threaded barrel sensors, with dead-stop; material:PA6QM-086945100Quick-mount bracket with dead-stop, chrome-plated brass, male thread M12 x 1. Note: The switchingdistance of proximity switches may be reduced through the use of quick-mount brackets.MW-086945008Mounting bracket for threaded barrelsensors; material: Stainless steel A21.4301 (AISI 304)BSS-086901322Mounting clamp for smooth and threaded barrel sensors; material:PolypropyleneMBS8069479Mounting clamp for smooth barrel sensors; mounting block material:Anodized aluminumWiring accessoriesDimension drawingTypeID RKC4.221T-2/TEB6628420Connection cable, female M12, straight,2-pin, cable length: 2 m, sheathmaterial: PVC, black; cULus approval;other cable lengths and qualities available, see WKC4.221T-2/TEB 6628427Connection cable, M12 femaleconnector, angled, 2-pin, cable length:2 m, jacket material: PVC, black; cULus approval; other cable lengths andqualities available, see N I 3-E G 08K -Y 1-H 1341 | 11/29/2022 05-07 | t e c h n i c a l c h a n g e s r e s e r v e dInstructions for useIntended useThis device fulfills Directive 2014/34/EC and is suited for use in areas exposed to explosion hazards according to EN 60079-0:2018 and EN 60079-11:2012.Further it is suited for use in safety-related systems, including SIL2 as per IEC61508.In order to ensure correct operation to the intended purpose it is required to observe the national regulations and directives.For use in explosion hazardous areas conform to classificationII 1 G and II 1 D (Group II, Category 1 G, electrical equipment for gaseous atmospheres and category 1 D, electrical equipment for dust atmospheres).Marking (see device or technical data sheet)É II 1 G and Ex ia IIC T6 Ga and É II 1 D Ex ia IIIC T135 °C Da acc. to EN 60079-0, -11Local admissible ambient temperature -25…+70 °CInstallation/CommissioningThese devices may only be installed, connected and operated by trained and qualified staff. Qualified staff must have knowledge of protection classes, directives and regulations concerning electrical equipment designed for use in explosion hazardous areas.Please verify that the classification and the marking on the device comply with the actual application conditions.This device is only suited for connection to approved Exi circuits according to EN 60079-0 and EN 60079-11. Please observe the maximum admissible electrical values.After connection to other circuits the sensor may no longer beused in Exi installations. When interconnected to (associated) electrical equipment, it is required to perform the "Proof of intrinsic safety" (EN60079-14).Attention! When used in safety systems, all content of the security manual must be observed.Installation and mounting instructionsAvoid static charging of cables and plastic devices. Please only clean the device with a damp cloth. Do not install the device in a dust flow and avoid build-up of dust deposits on the device.If the devices and the cable could be subject to mechanical damage, they must be protected accordingly. They must also be shielded against strong electro-magnetic fields.The pin configuration and the electrical specifications can be taken from the device marking or the technicaldata sheet.In order to avoid contamination of the device, please remove possible blanking plugs of the cable glands or connectors only shortly before inserting the cable or opening the cable socket.Service/MaintenanceRepairs are not possible. The approval expires if the device is repaired or modified by a person other than the manufacturer. The most important data from the approval are listed.。
标致4082011款16L手动豪华版基本参数
车体结构：
承载式
承载式
车轮制动
标致 408 2011 款 1.6L 手动豪华版 标致 408 2011 款 1.6L 手动舒适版
前制动器类型：
通风盘式
通风盘式
后制动器类型：
盘式
盘式
驻车制动类型：
手刹
手刹
前轮胎规格：
215/55 R16
215/55 R16
后轮胎规格：
215/55 R16
215/55 R16
CD 支持 MP3/WMA：
●
●
CD 支持 MP3/WMA：
CD 支持
单碟 CD：
●
●
单碟 CD：
单碟 DVD：
-
-
单碟 DVD：
多碟 DVD 系统：
-
-
多碟 DVD 系统：
多碟
4-5 喇叭扬声器系统：
-
●
6-7 喇叭扬声器系统：
●
-
灯光配置
标致 408 2011 款 标致 408 2011 款 1.6L 手动豪华版 1.6L 手动舒适版
180
180
整备质量(Kg)：
1431
1431
车身结构：
三厢车
三厢车
车门数(个)：
4
4
座位数(个)：
5
5
油箱容积(L)：
60
60
行李厢容积(L)：
562
562
发动机
标致 408 2011 款 1.6L 手动豪华版 标致 408 2011 款 1.6L 手动舒适版
发动机型号：
-
-
排量(mL)：
1587
肩部
前排座椅电动调节：
MT41K512M16VRN-107IT_P
TwinDie 1.35V DDR3L SDRAMMT41K512M16 – 64 Meg x 16 x 8 Banks DescriptionThe 8Gb (TwinDie) DDR3L SDRAM (1.35V) uses twoMicron 4Gb DDR3L SDRAM x8 die for a 2 byte x16 de-vice in one package. Refer to Micron’s 4Gb DDR3L SDRAM data sheet (x8 option) for specifications not included in this document, specifications for base part number MT41K512M8 correlate to TwinDie manufac-turing base part number MT41K512M16.Features•Uses two x8, 4Gb Micron die to make one x16 pack-age–Single rank TwinDie–One external ZQ ball and one internal ZQ con-nected to V SSQ through an embedded serial resis-tor•V DD = V DDQ = 1.35V (1.283–1.45V)•Backward compatible to V DD = V DDQ = 1.5V ±0.075V •Differential bidirectional data strobe •8n -bit prefetch architecture•Differential clock inputs (CK, CK#)•8 internal banks•Nominal and dynamic on-die termination (ODT)for data, strobe, and mask signals•Programmable CAS (READ) latency (CL)•Programmable posted CAS additive latency (AL)•Programmable CAS (WRITE) latency (CWL)•Fixed burst length (BL) of 8 and burst chop (BC) of 4(via the mode register set [MRS])•Selectable BC4 or BL8 on-the-fly (OTF)•Self refresh mode •T C of –40°C to +95°C–64ms, 8192-cycle refresh at –40°C to +85°C –32ms at +85°C to +95°C •Self refresh temperature (SRT)•Automatic self refresh (ASR)•Write leveling•Multipurpose register •Output driver calibration OptionsMarking•Configuration –512 Meg x 16512M16•TFBGA package (Pb-free) – x16–96-ball (8mm x 14mm) - SAC302VRN –96-ball (8mm x 14mm) - SACQ VRP •Timing – cycle time– 1.07ns @ CL = 13 (DDR3-1866)-107•Self refresh –StandardNone •Operating temperature–Industrial (–40°C ≤ T C ≤ +95°C)IT •Revision:PNotes:1.Not all options listed can be combined todefine an offered product. Use the part cat-alog search on for available offer-ings.2.For recommendation on PCB vs. componentpad dimension, see CSN-33: Micron BGA Manufacturer’s User Guide on .Table 1: Key Timing ParametersTable 2: AddressingFigure 1: DDR3L Part NumbersExample Part Number: MT41K512M16xxx-107 IT:PNote:1.Not all options listed can be combined to define an offered product. Use the part catalog search on for available offerings.8Gb: x16 TwinDie DDR3L SDRAMDescription质量等级领域:宇航级IC 、特军级IC 、超军级IC 、普军级IC 、禁运IC 、工业级IC ，军级二三极管，功率管等;应用领域:航空航天、船舶、汽车电子、军用计算机、铁路、医疗电子、通信网络、电力工业以及大型工业设备祝您:工作顺利，生活愉快!以深圳市美光存储技术有限公司提供的参数为例，以下为MT41K512M16VRN-107IT_P的详细参数，仅供参考Electrical SpecificationsAbsolute RatingsStresses greater than those listed may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other condi-tions outside those indicated in the operational sections of this specification is not im-plied. Exposure to absolute maximum rating conditions for extended periods may ad-versely affect reliability.Table 6: Absolute Maximum Ratings8Gb: x16 TwinDie DDR3L SDRAMElectrical Specifications。
MITREK系列产品说明书
CONTROL HEADREF.NO.PART NO.DESCRIPTIONREF.NO.PART NO.DESCRIPTIONBAR COPY IF NECESSARYLOW BAND RADIO ASSEMBLY 284180175A01Spring (3.05 MM OD), pivot 290310904A02Screw (3.5 x 6-PH-M)300480149A01Washer, captivitate 313280074A02Gasket, cable plug341484391F01Insulator Mica, transistor 350484180C01Washer, shoulder (nylon)360310905A01Screw, (9.0 x 6-FIL-M), transistor 371483572K01Insulator Mica, transistor39HLN4033BCover, bottom inner w/gasket(includes 1580004A01, cover, and 3280129F01, gasket400310906A19Screw (3.5 x 13-FH-M), inner cover 414280013A01Clip, coax (dress)440180701T74Conn. and Feed Through Caps 470780079A01Bracket, IC board support 492910271A15Pin, terminal512880141H03Plug, male (2.54 CTRS) (25 post)542880096A01Plug, male (3.96 CTRS)(4 post)553280080A01Gasket, antenna connector560280006A01Nut, spanner, antenna connector 570400114522Washer, lock, antenna connector 581480077A01Insulator, P.A. compartment 590780078A01Bracket, thermal device 602980014A01Clip, coax (terminal)631480179A01Insulator, mica10980028A01Socket, transistor2HLN4034C Bottom Cover, assembly40310906A05Screw (3.5 x 6-FH-M) bottom cover latch50180252J01Top Cover, assembly 64680026A01Stud Latch, top cover 87580178A01Pad, compression 90180252J01Housing, frame 104780027A01Pushbutton, latch 134180029A01Spring, latch140780016A02Bracket, lock slide 150780015A02Support, lock slide 164180022A01Spring, lock170310936B15Screw (3.5 x 13-FM-TH) holds lock slide 185584101B01Lock203280081A01Gasket, lock support 214380150A01Sleeve, cover release 235580002A01Handle240780113B01Spring, torsion 264780021A01Pin, pivotREF.NO.PART NO.DESCRIPTIONREF.NO.PART NO.DESCRIPTIONBAR COPY IF NECESSARYHIGH BAND RADIO ASSEMBLY 370310905A01Screw (3.0 x 6-FIL-M)392980014A01Clip, coax (terminal)40HLN4033BCover, bottom inner w/gasket (includes 1580004A01, cover and 3280129F01, gasket)410310906A19Screw (3.5 x 13-FH-M)434280013A01Clip, coax 442680211A01Shield, PA 455584300B04Handle, nylon460180701T74Conn. and Feed Through Caps 490780079A01Bracket, IC board support 512910271A15Pin, terminal520980028A01Socket, transistor 542880141H03Plug, male (25 post)572880096A01Plug, male (4 post)581580008A01Housing610280045A01Nut, retainer M5x1620200007003Nut, 8-32 x 5⁄16x 1⁄8hex643280080A01Gasket, antenna connector 650280006A01Nut, spanner 660400114522Washer, lock 671480077A01Insulator, PA680780078A01Bracket thermistar mounting12684716D01Heatsink3HLN4034C Bottom Cover, assembly 50310906A05Screw (3.5 x 6-FH-M)60180252J01Top Cover, assembly 74680026A01Stud, latch97580178A01Pad, compression 114780027A01Push Button 144180029A01Spring, latch150780016A02Bracket, lock slide 160780015A02Support, lock slide 174180022A01Spring, lock180310936B15Screw (3.5 x 13-FH-TH)195584101B01Lock213280081A01Gasket, lock support 224380150A01Sleeve, cover release 245580002A01Handle250780113B01Spring, torsion 274780021A01Pin, pivot294180175A01Spring (3.05 MM OD)300310904A02Screw (3.5 x 6-PH-M)310480149A01Washer, captive 323280074A02Gasket, cable plug 351484391F01Insulator, mica360484180C01Washer, shoulder nylonREF.NO.PART NO.DESCRIPTIONREF.NO.PART NO.DESCRIPTIONUHF ASSEMBLY410310906A19Screw (3.5 x 13-FH-M)434280013A01Clip, coax442680211A01Shield, PA455584300B04Handle, nylon460180701T74Conn. and Feed Through Caps490780079A01Bracket, IC512910271A15Pin, terminal520980028A01Socket, transistor542880141H03Plug, male (2.54 CTRS) (25 post)572880096A01Plug, male (3.96 CTRS) (4 post)604680009A01Stud, coil M6x1614680010A01Stud, coil M8x1.25620380012A03Screw, set M6x1630380256A01Screw, set M8x1.75640280045A03Nut, retainer M6x1.0650280045A02Nut, retainer M8x1.25670200007003Nut, 8.32 x 5⁄16x 1⁄8hex680480083A01Washer, stud device703280080A01Gasket, antenna connector710280006A01Nut, spanner720400114522Washer, lock7314-80077A01Insulator, PA740780078A01Bracket, thermal mount752980014A01Clip, coax (terminal)760780157A01Support, transistor PA771580003A01Housing, filter (harmonic)12684716D01Heatsink3HLN4034C Bottom Cover, assembly 50310906A05Screw (3.5 x 6-FH-M) 60180252J01Top Cover, assembly 70780015A02Stud, latch97580178A01Pad, compression114780027A01Push Button144180029A01Spring, latch150780016A02Bracket, lock slide160780015A01Support, lock slide174180022A01Spring, lock180310936B15Screw (3.5 x 13-FH-TH) 195584101B01Lock213280081A01Gasket, lock support 224380150A01Sleeve, cover release 245580002A01Handle250780113B01Spring, torsion274780021A01Pin, pivot294180175A01Spring (3.05 MM OD) 300310904A02Screw (3.5 x 6-PH-M) 310480149A01Washer, captive323280074A02Gasket, cable plug351484391F01Insulator, mica360484180C01Washer, shoulder370310905A01Screw (3.05 x 6-FIL-M) 390310936B06Screw (3.5 x 8-FILM-TF)40HLN4033B Cover, bottom inner w/gasket(includes 15-80004A01, cover)MOBILE MICROPHONESHMN1015AHLN4024Bmode while still on-hook arealso available.HLN4024BHang-up BoxHLN4025ATLN4698BCradle, Private-LineTLN4507ACradle with Slide SwitchTLN4505BCradle, Carrier SquelchHSN4009ACONTROL HEADSHLN4022EHLN4012ANOISE REDUCTION KITSSingle HousingConsists of a single housing with standard trunnion which can accommodate one, one board option and one alterna-tive control module.THN6125A HLN1002ATLN1391ATHN6125AMITREK SYSTEMS•90 ACCESSORIESHSN4010A Microphone Hang-upHLN4188AMOBILE ANTENNASRAB4012ARA RAB4013ARA&RAB4014ARA 6680385A04RSX4028AService Aids, Manuals SERVICE AIDSTEKA48。
汉字听写大会题库(三)
单词拼音序列年级级别（目前的级别）200011目光mù ɡuünɡ2001均可使用7目光炯炯mù ɡuünɡ jiǒnɡ jiǒnɡ2002均可使用11暮虢朝虞mù ɡuï zhüo yú2003均可使用7沐猴而冠mù hïu ãr ɡuàn 200445募集mù jí2005初中6木槿mù jǐn200655牡蛎mǔ lì200767幕僚mù liáo200865睦邻mù lín2009均可使用7木牛流马mù niú liú mǎ201036暮色mù sâ201145穆斯林mù sÿ lín2012均可使用6目无王法mù wú wánɡ fǎ2013初中8苜蓿mù xu201434沐浴mù yù201545沐雨栉风mù yǔ zhì fýnɡ2016初中9母株mǔ zhū2017初中10拏风跃云ná fýnɡ yuâ yún 2018均可使用9纳垢藏污nà ɡîu cánɡ wū2019初中10拿腔作调ná qiünɡ zuî diào 2020初中10拏云握雾ná yún wî wù202137奈何nài hã2022初中9耐人咀嚼nài rãn jǔ juã202334耐心nài xÿn202466难熬nán áo2025均可使用8男盗女娼nán dào nǚ chünɡ2026均可使用8难分难舍nán fýn nán shþ202734难过nán ɡuî2028初中12南橘北枳nán jú bþi zhǐ2029均可使用8南柯一梦nán ký yÿ mânɡ203054囡囡nün nün2031均可使用9喃喃自语nán nán zì yǔ203222难忘nán wànɡ2033均可使用8难兄难弟nàn xiōnɡ nàn dì2034初中9赧颜汗下nǎn yán hàn xià2035初中12南鹞北鹰nán yào bþi yÿnɡ2036初中12南州冠冕nán zhōu ɡuün miǎn 2037均可使用8男尊女卑nán zūn nǚ býi 203867囊括nánɡ kuî2039均可使用10囊萤积雪nánɡ yínɡ jÿ xuþ2040初中12囊锥露颖nánɡ zhuÿ lîu yǐnɡ2041均可使用10蛲虫náo chïnɡ2042初中12挠喉捩嗓náo hïu liâ sǎnɡ204336恼怒nǎo nù2044初中6孬种nüo zhǒnɡ2045初中9内峻外和nâi jùn wài hã2046初中12内修外攘nâi xiū wài rǎnɡ204766内蕴nâi yùn204814嫩绿nân lǜ204913能够nãnɡ ɡîu205021能力nãnɡ lì2051均可使用7能说会道nãnɡ shuō huì dào2052均可使用7能者多劳nãnɡ zhþ duō láo 205356溺爱nì ài205459拟定nǐ dìnɡ2055初中10匿迹销声nì jì xiüo shýnɡ2056均可使用6你来我往nǐ lái wǒ wǎnɡ205758泥泞ní nìnɡ205857泥鳅ní qiū2059均可使用12匿影藏形nì yǐnɡ cánɡ xínɡ2060初中9泥猪疥狗ní zhū jiâ ɡǒu 206156粘稠nián chïu2062初中10年羹尧nián ɡýnɡ yáo2063均可使用8辇毂之下niǎn ɡǔ zhÿ xià206454捻军起义niǎn jūn qǐ yì2065初中10黏吝缴绕nián lìn jiǎo rào 2066均可使用7念念不忘niàn niàn bù wànɡ2067均可使用6年轻力壮nián qÿnɡ lì zhuànɡ206821念书niàn shū2069初中12拈酸泼醋niün suün pō cù2070初中7碾碎niǎn suì207167黏土nián tǔ2072初中7捻土为香niǎn tǔ wãi xiünɡ2073初中10年逾古稀nián yú ɡǔ xÿ2074初中11鲇鱼上竹nián yú shànɡ zhú2075初中12念兹在兹niàn zÿ zài zÿ207657酿酒niànɡ jiǔ2077初中8鸟伏兽穷niǎo fú shîu qiïnɡ207849鸟瞰niǎo kàn2079初中10袅袅娉娉niǎo niǎo pÿnɡ pÿnɡ2080初中10袅袅余音niǎo niǎo yú yÿn 2081均可使用7鸟兽散niǎo shîu sàn2082初中9鸟啼花怨niǎo tí huü yuàn 2083均可使用7鸟语花香niǎo yǔ huü xiünɡ2084初中8啮齿niâ chǐ208546涅而不缁niâ ãr bù zÿ208647嗫嚅niâ rú208767蹑手蹑脚niâ shǒu niâ jiǎo 2088均可使用11啮雪餐毡niâ xuþ cün zhün 2089初中11啮血为盟niâ xuâ wãi mãnɡ2090均可使用11蹑影追风niâ yǐnɡ zhuÿ fýnɡ2091初中9孽障niâ zhànɡ2092初中12蹑足潜踪niâ zú qián zōnɡ209347凝结nínɡ jiã209422宁静nínɡ jìnɡ2095初中9宁缺毋滥nìnɡ quý wú làn 209647凝视nínɡ shì209746凝望nínɡ wànɡ209845狞笑nínɡ xiào2099初中9凝噎nínɡ yý210057宁愿nìnɡ yuàn210135纽带niǔ dài2102初中10牛骥同槽niú jì tïnɡ cáo 210365扭捏niǔ nie2104初中11牛溲马勃niú sōu mǎ bï2105初中10牛蹄之涔niú tí zhÿ cãn 210657扭转niǔ zhuǎn2107初中7哝哝nïnɡ nonɡ2108均可使用10怒艴nù fú210968怒吼nù hǒu211034努力nǔ lì211166驽马nú mǎ2112初中12怒猊渴骥nù ní kþ jì2113初中10奴颜媚骨nú yán mâi ɡǔ2114初中6努嘴nǔ zuǐ211523暖和nuǎn huo2116初中10虐人害物nûâ rãn hài wù211759挪动nuï donɡ211856懦夫nuî fū211946糯米nuî mǐ212038懦弱nuî ruî2121初中7挪威人nuï wýi rãn212244诺言nuî yán2123均可使用10搦战nuî zhàn2124初中11噢休ō xiū2125初中12喔咿儒睨ō yÿ rú nì2126初中11鸥波萍迹ōu bō pínɡ jì2127初中11齵差ïu chà2128初中11塸埞ōu dÿ212955藕断丝连ǒu duàn sÿ lián 213034偶尔ǒu þr2131初中11欧风墨雨ōu fýnɡ mî yǔ2132初中11沤榔ōu lánɡ2133初中11沤麻îu má2134初中11沤沫槿艳ōu mî jǐn yàn2135初中11沤泡ōu pào213634怄气îu qì213735偶然ǒu rán2138初中11鸥汀ōu tÿnɡ2139初中10吽呀ōu yü2140初中10沤珠槿艳ōu zhū jǐn yàn 2141初中11扒耳搔腮pá þr süo süi 214255爬犁pá li2143611爬罗剔抉pá luï tÿ juã214444耙子pá zi214559徘徊pái huái214668排糠障风pái künɡ zhànɡ fýnɡ214734派遣pài qiǎn214858排泄pái xiâ214969俳优畜之pái yōu xù zhÿ215069攀登pün dýnɡ215157判断pàn duàn2152612槃根错节pán ɡýn cuî jiã2153均可使用7盘根错节pán ɡýn cuî jiã2154均可使用9攀龙附凤pün lïnɡ fù fânɡ2155411判若鸿沟pàn ruî hïnɡ ɡōu215655蹒跚pán shün2157初中9磐石之安pán shí zhÿ ün 215845蟠桃pán táo2159初中12攀藤揽葛pün tãnɡ lǎn ɡã216026盘旋pán xuán216146番禺pün yú2162初中9攀辕卧辙pün yuán wî zhã216334磅礴pánɡ bï216456膀胱pánɡ ɡuünɡ216556彷徨失措pánɡ huánɡ shÿ cuî216659庞眉皓首pánɡ mãi hào shǒu 2167均可使用7旁敲侧击pánɡ qiüo câ jÿ216833滂沱pünɡ tuï2169均可使用8滂沱大雨pünɡ tuï dà yǔ2170初中5螃蟹pánɡ xiâ2171均可使用7刨根问底páo ɡýn wân dǐ2172均可使用10袍笏登场páo hù dýnɡ chǎnɡ2173初中9砲龙烹凤pào lïnɡ pýnɡ fânɡ2174初中6疱疹pào zhþn217524狍子páo zi217626胚芽pýi yá217769沛雨甘霖pâi yǔ ɡün lín 2178初中11蓬筚生辉pãnɡ bì shýnɡ huÿ2179均可使用8鹏程万里pãnɡ chãnɡ wàn lǐ2180均可使用7捧腹大笑pþnɡ fù dà xiào 218158怦然心动pýnɡ rán xÿn dînɡ2182均可使用9蓬头垢面pãnɡ tïu ɡîu miàn 218359蓬头跣足pãnɡ tïu xiǎn zú218434碰撞pânɡ zhuànɡ218545批驳pÿ bï2186均可使用10蚍蜉戴盆pí fú dài pãn2187均可使用7屁滚尿流pì ɡǔn niào liú2188初中12被褐怀玉pÿ hâ huái yù2189初中10批砉导窾pÿ huü dǎo kuǎn 219067否极泰来pǐ jí tài lái2191初中12被甲据鞍pÿ jiǎ jù ün2192初中8裨将pí jiànɡ2193均可使用8披荆斩棘pÿ jÿnɡ zhǎn jí2194均可使用7皮开肉绽pí küi rîu zhàn 219557批亢捣虚pÿ kànɡ dǎo xū2196均可使用10睥睨一世pì nì yÿ shì2197均可使用7披头散发pÿ tïu sàn fà2198612貔貅pí xiū2199初中10骈拇枝指pián mǔ zhÿ zhǐ2200均可使用10翩翩起舞piün piün qǐ wǔ2201均可使用10翩翩少年piün piün shào nián 2202初中9偏瘫piün tün2203均可使用7片言只字piàn yán zhÿ zì220446嘌呤piào lìnɡ2205初中10飘萍断梗piüo pínɡ duàn ɡþnɡ2206均可使用12螵蛸piüo xiüo2207初中9飘移piüo yí2208均可使用8贫病交加pín bìnɡ jiüo jiü2209初中10牝牡骊黄pìn mǔ lí huánɡ2210均可使用8品头论足pǐn tïu lùn zú221122评比pínɡ bǐ2212初中10冯河暴虎pínɡ hã bào hǔ221348平衡pínɡ hãnɡ221444平均pínɡ jūn221521评论pínɡ lùn2216均可使用12瓶罄罍耻pínɡ qìnɡ lãi chǐ2217初中9凭眺pínɡ tiào2218初中11娉婷袅娜pÿnɡ tínɡ niǎo nuï221945平稳pínɡ wþn2220初中9平衍pínɡ yǎn222136破裂pî liâ222223破碎pî suì2223初中11破甑不顾pî zânɡ bù ɡù222445普遍pǔ biàn222569瀑布pù bù2226初中9堡堠pù hîu222744普及pǔ jí2228均可使用11氆氇pǔ lu222935朴素pǔ sù223057普通pǔ tōnɡ223147铺展pū zhǎn223246凄惨qÿ cǎn223346祈祷qí dǎo223444启发qǐ fü223544气愤qì fân223657气氛qì fýn2237初中9凄风苦雨qÿ fýnɡ kǔ yǔ223825起伏qǐ fú223934欺负qÿ fu224046气概qì ɡài224121奇怪qí ɡuài224236起航qǐ hánɡ224346漆黑qÿ hýi224444奇迹qí jì224548迄今qì jÿn2246初中9耆老qí lǎo2247均可使用10嘁哩喀喳qÿ li kü chü224868凄凉qÿ liánɡ224968起码qǐ mǎ225045起锚qǐ máo225134奇妙qí miào225249气馁qì nþi225358企盼qǐ pàn225468欺骗qÿ piàn225546气魄qì pî225657祈求qí qiú225758崎岖qí qū225845启示qǐ shì225927启事qǐ shì226048起誓qǐ shì2261均可使用11耆寿耇老qí shîu ɡǒu lǎo226224奇特qí tâ226359歧途qí tú226421气味qì wâi226546欺侮qÿ wǔ226658栖息qÿ xÿ226735奇异qí yì226844其余qí yú226945起源qǐ yuán227069旗帜qí zhì227158岂止qǐ zhǐ227234恰好qià hǎo227344恰恰qià qià227467前辈qián bâi227568潜藏qián cánɡ227646浅尝辄止qiǎn chánɡ zhã zhǐ227749遣返qiǎn fǎn227823牵挂qiün ɡuà2279初中9堑壕qiàn háo228068虔敬qián jìnɡ2281初中10歉疚qiàn jiù2282初中11掮客qián kâ2283初中12缱绻qiǎn quǎn228446谦让qiün rànɡ228548嵌入qiàn rù228611千万qiün wàn228736谦虚qiün xū228848谴责qiǎn zã228947箝制qián zhì2290511襁褓qiǎnɡ bǎo2291初中9强弩之末qiánɡ nǔ zhÿ mî2292初中8镪水qiünɡ shuǐ2293均可使用12挈榼提壶qiâ ký tí hú2294初中9伽蓝qiã lán229524清澈qÿnɡ châ229622清晨qÿnɡ chãn229745清楚qÿnɡ chu229846清脆qÿnɡ cuì229934情况qínɡ kuànɡ230022晴朗qínɡ lǎnɡ230134清凉qÿnɡ liánɡ230221请求qǐnɡ qiú230367清爽qÿnɡ shuǎnɡ230446清晰qÿnɡ xÿ230535清闲qÿnɡ xián230648倾泻qÿnɡ xiâ230736情绪qínɡ xù230848清幽qÿnɡ yōu2309均可使用10茕孑qiïnɡ jiã231068泅渡qiú dù2311初中12虬髯qiú rán231237屈服qū fú2313均可使用11鼩鼱qú jÿnɡ231446屈辱qū rǔ231544曲折qū zhã231614全部quán bù231723劝告quàn ɡào231869权衡quán hãnɡ231946权威quán wýi232037劝阻quàn zǔ2321均可使用12鹊巢鸠据quâ cháo jiū jù232234确定quâ dìnɡ232357缺乏quý fá232434确认quâ rân232545缺少quý shǎo232634群众qún zhînɡ232722然而rán ãr232868染翰成章rǎn hàn chãnɡ zhünɡ232921然后rán hîu2330均可使用12然糠照薪rán künɡ zhào xÿn 2331初中9燃萁煎豆rán qí jiün dîu 233236燃烧rán shüo233315让步rànɡ bù2334初中8穰穰满家ránɡ ránɡ mǎn jiü233546桡骨ráo ɡǔ233668饶恕ráo shù233713热爱râ ài2338初中9热熬翻饼râ áo fün bǐnɡ233927热忱râ chãn234035热烈râ liâ234112热闹râ nɑo234226热腾腾râ tãnɡ tãnɡ234335仁爱rãn ài234411人才rãn cái2345610人稠物穰rãn chïu wù ránɡ234658仁慈rãn cí234723任何rân hã234811人民rãn mín234945任凭rân pínɡ235067荏苒rþn rǎn235157妊娠rân shýn235244认识rân shi2353初中10衽扱囊括rân xÿ nánɡ kuî235427任意rân yì235534仍然rãnɡ rán235635日暮rì mù235723溶解rïnɡ jiþ2358均可使用10戎马劻勷rïnɡ mǎ kuünɡ ránɡ235968融洽rïnɡ qià236034容易rïnɡ yì236165戎夷解衣rïnɡ yí jiþ yÿ236268荣膺rïnɡ yÿnɡ236326柔和rïu hã2364初中12蹂躏rïu lìn236513柔嫩rïu nân2366均可使用11柔懦寡断rïu nuî ɡuǎ duàn 236727柔顺rïu shùn2368初中9鞣酸rïu suün236958蠕动rú dînɡrǔ dú bù pà hǔ2370初中12乳犊不怕虎237121如果rú ɡuǒ237225辱骂rǔ mà2373初中12如蚁慕膻rú yǐ mù shün2374初中9如锥画沙rú zhuÿ huà shü2375均可使用9阮囊羞涩ruǎn nánɡ xiū sâ237657软硬兼施ruǎn yìnɡ jiün shÿ237769锐挫气索ruì cuî qì suǒ237857锐利ruì lì2379初中8枘凿方圆ruì záo fünɡ yuán 2380初中9睿智ruì zhì2381初中11润屋润身rùn wū rùn shýn 238256若敖之鬼ruî áo zhÿ ɡuǐ2383均可使用11挼捺ruï nà238458撒谎sü huǎnɡ2385初中10三聚氰胺sün jù qínɡ àn 2386均可使用10桑弧蓬矢sünɡ hú pãnɡ shǐ2387均可使用10唼喋shà zhá2388均可使用11鄯善shàn shàn238945稍微shüo wýi239067涉及shâ jí239135设计shâ jì2392均可使用11阇梨shã lí2393均可使用11摄威擅势shâ wýi shàn shì239439摄影shâ yǐnɡ239511什么shãn me239635神秘shãn mì239734神奇shãn qí239822深浅shýn qiǎn239958身躯shýn qū240057神圣shãn shânɡ240157呻吟shýn yín240268慎重shân zhînɡ240344生存shýnɡ cún240436圣诞shânɡ dàn240535圣地shânɡ dì240622盛开shânɡ küi240734胜利shânɡ lì240811生气shýnɡ qì2409均可使用10笙磬同音shýnɡ qìnɡ tïnɡ yÿn 2410610鼪鼯之径shýnɡ wú zhÿ jìnɡ2411均可使用9生息蕃庶shýnɡ xÿ fán shù241222剩下shânɡ xià241355恃才傲物shì cái ào wù241438湿度shÿ dù241512是非shì fýi241634是否shì fǒu241723师傅shÿ fu241867施工shÿ ɡōnɡ241944适合shì hã242013时候shí hou242146侍候shì hîu242224世纪shì jì2423均可使用12嗜痂成癖shì jiü chãnɡ pǐ242445实践shí jiàn242521世界shì jiâ242622使劲shǐ jìn242722时刻shí kâ242868湿淋淋shÿ lín lín 2429均可使用12噬脐莫及shì qí mî jí243023事情shì qinɡ243158逝世shì shì243244尸体shÿ tǐ243323失望shÿ wànɡ243434实现shí xiàn243535视线shì xiàn243635实验shí yàn243713试验shì yàn243836适宜shì yí243934适应shì yìnɡ244021使用shǐ yînɡ2441均可使用10螫针shì zhýn244244守护shǒu hù244323收获shōu huî244458狩猎shîu liâ244546瘦弱shîu ruî244634收拾shōu shi244711手术shǒu shù244821首先shǒu xiün 244958授予shîu yǔ245068手镯shǒu zhuï245137受罪shîu zuì245236舒畅shū chànɡ245367抒发shū fü245435舒服shū fu245538曙光shǔ ɡuünɡ245623梳理shū lǐ245736熟练shú liàn245845舒适shū shì245934戍守shù shǒu246036输送shū sînɡ2461均可使用10菽粟shū sù246236熟悉shú xi2463均可使用10束脩shù xiū246436输血shū xuâ246535属于shǔ yú2466均可使用11薯蓣科shǔ yù ký246723舒展shū zhǎn246869赎罪shú zuì246968耍弄shuǎ nînɡ247026衰败shuüi bài 247136摔倒shuüi dǎo2472均可使用10率尔操觚shuài ãr cüo ɡū247369摔跤shuüi jiüo 247445衰老shuüi lǎo247558衰弱shuüi ruî247668爽朗shuǎnɡ lǎnɡ2477均可使用11双瞳剪水shuünɡ tïnɡ jiǎn shuǐ247846睡眠shuì mián247959瞬间shùn jiün248022顺利shùn lì248134顺序shùn xù248257硕大shuî dà248358说谎shuō huǎnɡ248434似乎sì hū248559伺机sì jÿ2486均可使用11肆奸植党sì jiün zhí dǎnɡ248749嘶叫sÿ jiào248812思考sÿ kǎo248934思念sÿ niàn249056肆虐sì nûâ249137私塾sÿ shú249223思索sÿ suǒ2493初中9肆无忌惮sì wú jì dàn249446嘶哑sÿ yǎ249535饲养sì yǎnɡ2496均可使用11耸壑昂霄sǒnɡ hâ ánɡ xiüo 249724耸肩sǒnɡ jiün249867耸立sǒnɡ lì2499初中10怂恿sǒnɡ yǒnɡ250058搜查sōu chá250146搜集sōu jí250244搜罗sōu luï250357搜索sōu suǒ250445搜寻sōu xún250536苏醒sū xǐnɡ250645俗语sú yǔ2507均可使用12蒜薹suàn tái2508初中7苔藓tái xiǎn2509初中7弹劾tán hã2510均可使用11炭墼tàn jÿ2511初中7探囊取物tàn nánɡ qǔ wù251256弹奏tán zîu2513初中6搪瓷tánɡ cí251456堂屋tánɡ wū2515初中12陶熔鼓铸táo rïnɡ ɡǔ zhù2516均可使用12饕餮之徒tüo tiâ zhÿ tú251744特殊tâ shū251836腾飞tãnɡ fýi2519初中9藤蔓tãnɡ wàn252069誊写tãnɡ xiþ252157提供tí ɡōnɡ2522初中10醍醐灌顶tí hú ɡuàn dǐnɡ2523初中12啼饥号寒tí jÿ háo hán2524初中7蹄髈tí pǎnɡ2525初中6提携tí xiã2526初中6恬不知耻tián bù zhÿ chǐ252767天道酬勤tiün dào chïu qín252811田地tián dì2529均可使用12天阍tiün hūn253068恬静tián jìnɡ253111天空tiün kōnɡ253246天涯tiün yá253321田野tián yþ253427挑逗tiǎo dîu2535初中12粜风卖雨tiào fýnɡ mài yǔ2536初中7调羹tiáo ɡýnɡ2537均可使用11调和鼎鼐tiáo hã dǐnɡ nài 253834调节tiáo jiã253958眺望tiào wànɡ254023挑选tiüo xuǎn254117跳跃tiào yuâ254235停泊tínɡ bï254321停止tínɡ zhǐ254445同胞tïnɡ büo2545初中6同仇敌忾tïnɡ chïu dí kài 254634通过tōnɡ ɡuî254735痛苦tînɡ kǔ2548初中6通衢tōnɡ qú2549初中12童山濯濯tïnɡ shün zhuï zhuï255011同时tïnɡ shí255146统率tǒnɡ shuài2552初中6童叟tïnɡ sǒu255325通信tōnɡ xìn255444统一tǒnɡ yÿ255524透明tîu mínɡ255646偷袭tōu xí255745图案tú àn2558初中7秃鹫tū jiù2559初中6屠戮tú lù2560初中7荼蘼tú mí256121突然tū rán2562均可使用10彖辞tuàn cí256358湍急tuün jí256436推测tuÿ câ256567推辞tuÿ cí256635推动tuÿ dînɡ256758推荐tuÿ jiàn256859推敲tuÿ qiüo256922退却tuì quâ257069颓丧tuí sànɡ257146推移tuÿ yí2572初中12颓垣败壁tuí yuán bài bì2573初中7囤积tún jÿ2574初中12豚蹄穰田tún tí ránɡ tián 2575初中8拓跋tuî bá257647拖累tuō lþi2577均可使用12鼍龙tuï lïnɡ257858拖沓tuō tà257935脱险tuō xiǎn258068妥协tuǒ xiã258153挖耳当招wü þr dünɡ zhüo 258236挖掘wü juã258364蛙蟆胜负wü má shânɡ fù258432挖肉补疮wü rîu bǔ chuünɡ2585初中5哇塞wü süi258641佤族wǎ zú258735外宾wài bÿn258836歪斜wüi xiã258968挽救wǎn jiù259034玩具wán jù259142纨绔wán kù259269挽联wǎn lián2593均可使用11顽廉懦立wán lián nuî lì259436挽留wǎn liú259556皖南事变wǎn nán shì biàn 259645顽皮wán pí259736顽强wán qiánɡ259821弯曲wün qū259957宛如wǎn rú260068宛若wǎn ruî260114玩耍wán shuǎ260213晚霞wǎn xiá260354顽癣wán xuǎn260469蜿蜒wün yán260536完整wán zhþnɡ260638婉转wǎn zhuǎn260751忘餐废寝wànɡ cün fâi qǐn 260847忘啜废枕wànɡ chuî fâi zhþn 260921忘记wànɡ jì2610初中5惘然wǎnɡ rán261136旺盛wànɡ shânɡ261258妄想wànɡ xiǎnɡ261363汪洋恣肆wünɡ yánɡ zì sì261412尾巴wþi bɑ261521伟大wþi dà261657唯独wãi dú261769巍峨wýi ã261834违反wãi fǎn261935威风wýi fýnɡ262047桅杆wãi ɡün2621612为鬼为蜮wãi ɡuǐ wãi yù262245危害wýi hài2623612为虺弗摧wãi huǐ fú cuÿ262439畏惧wâi jù262535违抗wãi kànɡ262621未来wâi lái262736蔚蓝wâi lán262823为难wãi nán262946为裘为箕wãi qiú wãi jÿ263046围绕wãi rào263157微弱wýi ruî263221卫生wâi shýnɡ263369萎缩wþi suō263465维他命wãi tü mìnɡ2635210味同嚼蜡wâi tïnɡ jiáo là263636微微wýi wýi2637初中12亹亹不倦wþi wþi bù juàn 263836威武wýi wǔ263944危险wýi xiǎn264023微笑wýi xiào264158威胁wýi xiã264259逶迤wýi yí264346位置wâi zhì264457伪装wþi zhuünɡ264525稳固wþn ɡù264646吻合wþn hã264724温和wýn hã264821文化wãn huà264962文君新醮wãn jūn xÿn jiào 265034闻名wãn mínɡ265135温暖wýn nuǎn265213问题wân tí2653均可使用10文修武偃wãn xiū wǔ yǎn 265467文章wãn zhünɡ2655均可使用10翁同和wýnɡ tïnɡ hã2656均可使用11瓮牖绳枢wânɡ yǒu shãnɡ shū265755蓊郁wþnɡ yù265831倭奴wō nú265946握手wî shǒu266025涡旋wō xuán266153恶不去善wù bù qù shàn 266214无敌wú dí266349无辜wú ɡū266422乌黑wū hýi2665初中9芜菁wú jÿnɡ266634无论wú lùn266745污染wū rǎn266858呜咽wū yâ266943蹊径xÿ jìnɡ267034嬉笑怒骂xÿ xiào nù mà267155瑕不掩瑜xiá bù yǎn yú2672均可使用10夏鲧xià ɡǔn267359枭首示众xiüo shǒu shì zhînɡ2674均可使用10猇亭xiüo tínɡ2675初中11歇鞍xiý ün2676均可使用11躞蹀xiâ diã2677均可使用10颉颃xiã hánɡ2678均可使用12鞋襻xiã pàn2679均可使用12獬豸xiâ zhì2680初中9心猿意马xÿn yuán yì mǎ268157雄浑xiïnɡ hún268236凶猛xiōnɡ mþnɡ268336胸脯xiōnɡ pú268459胸膛xiōnɡ tánɡ268545雄伟xiïnɡ wþi268625汹涌xiōnɡ yǒnɡ268736羞耻xiū chǐ268835修建xiū jiàn 268959羞愧xiū kuì269035秀丽xiù lì269168羞辱xiū rǔ269269羞涩xiū sâ269321休息xiū xi269446修筑xiū zhù269511许多xǔ duō2696均可使用10勖勉xù miǎn269736虚弱xū ruî269835需要xū yào269925宣布xuün bù270047宣告xuün ɡào 270136悬挂xuán ɡuà270258喧哗xuün huá270355璇玑xuán jÿ270457喧闹xuün nào 270568渲染xuàn rǎn 270646悬崖xuán yá270759炫耀xuàn yào 270834选择xuǎn zã270936旋转xuán zhuǎn 271011雪白xuþ bái271168削弱xuý ruî2712均可使用10雪霰xuþ xiàn2713均可使用10雪鸮xuþ xiüo2714均可使用10靴靿xuý yào271545血液xuâ yâ271648训斥xùn chì271767循环xún huán 271846巡警xún jǐnɡ271958驯良xùn liánɡ272036巡逻xún luï272168殉难xùn nàn272212询问xún wân272367驯养xùn yǎnɡ2724均可使用11薰莸异器xūn yïu yì qì2725均可使用11巽隅xùn yú272634寻找xún zhǎo 272759殉职xùn zhí272844压迫yü pî272969压抑yü yì273067睚眦必报yá zì bì bào 273123严寒yán hán2732均可使用11燕颔虎颈yàn hàn hǔ jǐnɡ273346掩护yǎn hù2734均可使用10偃蹇yǎn jiǎn 273513眼界yǎn jiâ273649严谨yán jǐn273725研究yán jiū273836严厉yán lì273946眼帘yǎn lián 274026严密yán mì274145淹没yün mî274257颜色yán sâ274345延伸yán shýn274458严肃yán sù274535沿途yán tú274636掩映yǎn yìnɡ274746眼睁睁yǎn zhýnɡ zhýnɡ274847研制yán zhì274935严重yán zhînɡ2750均可使用10兖州yǎn zhōu275135演奏yǎn zîu2752均可使用11羊触藩篱yánɡ chù fün lí275311阳光yánɡ ɡuünɡ275438仰慕yǎnɡ mù2755均可使用11扬葩振藻yánɡ pü zhân zǎo 275624样式yànɡ shì275745仰望yǎnɡ wànɡ275859洋溢yánɡ yì275935摇摆yáo bǎi276044药材yào cái276169窑洞yáo dînɡ276234妖怪yüo ɡuài276367吆喝yüo he276434摇晃yáo huànɡ276545遥控yáo kînɡ276657摇篮yáo lán276758邀请yüo qǐnɡ276821要求yüo qiú276968要挟yüo xiã277069摇曳yáo yâ277122遥远yáo yuǎn277212夜空yâ kōnɡ277359冶炼yþ liàn277446夜幕yâ mù277511也许yþ xǔ277634一般yÿ bün2777均可使用12虉草yì cǎo277836遗产yí chǎn277934异常yì chánɡ278011一定yÿ dìnɡ278123移动yí dînɡ278236一番yÿ fün278359遗憾yí hàn278436疑惑yí huî278546遗迹yí jì278621已经yǐ jÿnɡ278744依旧yÿ jiù278835依靠yÿ kào278946依赖yÿ lài279058屹立yì lì279168毅力yì lì279222议论yì lùn2793均可使用9旖旎风光yǐ nǐ fýnɡ ɡuünɡ279411一切yÿ qiâ279568毅然yì rán279634依然yÿ rán2797均可使用11一觞一咏yÿ shünɡ yÿ yǒnɡ279826仪式yí shì279922意思yì si280047仪态yí tài280135疑问yí wân280245义务yì wù2803均可使用10一薰一莸yÿ xūn yÿ yïu 280444意义yì yì2805均可使用9悒悒不欢yì yì bù huün 2806均可使用9薏苡明珠yì yǐ mínɡ zhū2807均可使用10瘗玉埋香yì yù mái xiünɡ2808均可使用10遗簪堕珥yí zün duî þr 280911一张一弛yÿ zhünɡ yÿ chí281046移植yí zhí281146隐蔽yǐn bì2812均可使用11饮冰茹蘗yǐn bÿnɡ rú bî281325隐藏yǐn cánɡ281422引导yǐn dǎo2815均可使用12狺吠yín fâi2816均可使用10窨井yìn jǐnɡ281767吟诵yín sînɡ2818均可使用10隐慝yǐn tâ281921因为yÿn wâi282022印象yìn xiànɡ2821均可使用9因循苟简yÿn xún ɡǒu jiǎn 282258引诱yǐn yîu282321音乐yÿn yuâ282469音韵yÿn yùn2825均可使用10氤氲叆叇yÿn yūn ài dài 2826均可使用12阴骘文yÿn zhì wãn 282746婴儿yÿnɡ ãr282821应该yÿnɡ ɡüi282936迎候yínɡ hîu283035迎接yínɡ jiý2831均可使用11鹰瞵鹗视yÿnɡ lín â shì283223英明yÿnɡ mínɡ2833均可使用11鹰觑鹘望yÿnɡ qù hú wànɡ2834均可使用10郢人斫垩yǐnɡ rãn zhuï â283522英雄yÿnɡ xiïnɡ2836均可使用11映雪囊萤yìnɡ xuþ nánɡ yínɡ283735营养yínɡ yǎnɡ2838均可使用12瘿肿yǐnɡ zhǒnɡ283923拥抱yōnɡ bào284022勇敢yǒnɡ ɡǎn284135拥挤yōnɡ jǐ2842均可使用10痈疽yōnɡ jū284334勇气yǒnɡ qì2844均可使用11饔飧不饱yōnɡ sūn bù bǎo 2845均可使用12饔飧不继yōnɡ sūn bù jì284611用心yînɡ xÿn284712拥有yōnɡ yǒu284821永远yǒnɡ yuǎn2849均可使用12饔飦yōnɡ zhün 285044优点yōu diǎn285126诱饵yîu þr2852均可使用12幽闺弱质yōu ɡuÿ ruî zhì285311友好yǒu hǎo285458诱惑yîu huî285559幽静yōu jìnɡ285635游览yïu lǎn285768忧虑yōu lǜ285822优美yōu mþi285958幽默yōu mî286034尤其yïu qí286136有趣yǒu qù286235犹如yïu rú286334游戏yïu xì286434幼小yîu xiǎo286557有效yǒu xiào286622优秀yōu xiù286735优雅yōu yǎ286823悠扬yōu yánɡ286914友谊yǒu yì287044有益yǒu yì287123游泳yïu yǒnɡ287267悠悠yōu yōu287369犹豫yïu yù287425幼稚园yîu zhì yuán 2875均可使用12牖中窥日yǒu zhōnɡ kuÿ rì287624预报yù bào287744预备役yù bâi yì287859愚蠢yú chǔn287958鱼饵yú þr2880均可使用12余膏剩馥yú ɡüo shânɡ fù288136愈合yù hã288228余晖yú huÿ288368迂回yū huí288435愉快yú kuài288557娱乐yú lâ288647舆论yú lùn2887均可使用11燠沐yù mù288854淤泥yū ní2889均可使用10玉箧yù qiâ289023熨帖yù tiý289123欲望yù wànɡ289258寓言yù yán2893均可使用10鱼跃鸢飞yú yuâ yuün fýi 289468预兆yù zhào289557宇宙yǔ zhîu289638渊博yuün bï2897均可使用11元恶大憝yuán â dà duì289846缘故yuán ɡù289946援救yuán jiù290067原谅yuán liànɡ2901均可使用9援溺振渴yuán nì zhân kþ2902均可使用10渊薮yuün sǒu。
暗送秋波 2011款雪铁龙C5
色 的驾驶乐趣 能吸 引年轻消 费者
２Ｏ１１ Ｏ１ ，
底 盘 功 底 就 相 当扎 实 ，有 了 “ 品 飞 靴 ” 极
ｌ Ｍ减震韧性多连 后Ｆ Ｌ 杆式 独立悬挂
一 Ｉ 前通风盘后盘式刹车 ｌ 轮胎规格 ２ ５ ５ １ ２ ／５Ｒ７
最高车速 ２ ／ ］ｋ ｈ ８ｍ 工信部油耗９ ｌＯｍ ＬＯｋ ５／
的加 盟 Ｃ５变得 更 为全 面 了，高速路 的行驶
的稳 定 性 也 相 应 提 高 。
臣
丽 —一
。
看来 Ｃ ５不 单 能满 足 车主 的 商务 需要 ， 还 能 为他 们 提供 相 当愉 悦 的 驾驶 乐 趣。 除 此 之外 ，作 为尊雅型增 强版 出现的 ２３尊 驭 型 ，多 出的 ５ ｏ Ｏ ０元还 包括 了增加 的前后 两 侧 的安全 气帘 ，是一 款值得 推荐 的车型。
－ ．驾驶 报告
２０１１Ｏ１ ／
雪铁龙Ｃ ．尊驭 型 ５２ ３
们 再也 无 法按 撩 重 逢 的喜悦 ，决定 立刻 与
它 上 路 一 叙 。 ２３升 发 动 机 在 ６挡 自动 变 速 ．
ｆ 前置前驱
ｌ挡手自—体 变速箱 ６
ｌ 前麦弗逊式独立悬挂
箱配合 下 ，轻 快安静地 带上我们 出发 了。 在城 市 道 路 ，单导 向公 路性 能 轮胎 的 底 线 不会 为你 所 知 ，只 有在 你 想找 点 刺激 ２３ 驭型 增加 了后安 全气 帘 尊 的弯角 ，才会感 受到它 的存在。 本来 Ｃ５的
外 观 大 气 典 雅 ，内 饰 颜 色 可选
择 ，动 力 顺 畅 ，空 间 乘 坐 舒 适
◇ 黑 色内饰镀铬亮条有点扎眼 ，没有 Ｊ接 口显得不够方便 ） ‘
宝来不同配置
1335 三厢车 4 5 55 450
1315 三厢车 4 5 55 450
1335 三厢车 4 5 55 450
宝来 2011 宝来 2011 宝来 2011 宝来 2011 宝来 2011 宝来 2011 宝来 2011 宝来 2011 款 1.6L 手 款 1.6L 自 款 1.6L 手 款 1.6L 自 款 1.4T 手 款 1.4T 自 款 1.4T 手 款 1.4T 自 劢时尚型 劢时尚型 劢舒适型 劢舒适型 劢舒适型 劢舒适型 劢豪华型 劢豪华型 EA111 1598 1.6 自然吸气 L 4 4 DOHC 105 77 5600 155 3800 汽油 93号 EA111 1598 1.6 自然吸气 L 4 4 DOHC 105 77 5600 155 3800 汽油 93号 EA111 1598 1.6 自然吸气 L 4 4 DOHC 105 77 5600 155 3800 汽油 93号 EA111 1390 1.4 涡轮增压 L 4 4 DOHC 76.5 75.6 131 96 5000 220 17503500 汽油 93号 EA111 1390 1.4 涡轮增压 L 4 4 DOHC 76.5 75.6 131 96 5000 220 17503500 汽油 93号 EA111 1390 1.4 涡轮增压 L 4 4 DOHC 76.5 75.6 131 96 5000 220 17503500 汽油 93号 EA111 1390 1.4 涡轮增压 L 4 4 DOHC 76.5 75.6 131 96 5000 220 17503500 汽油 93号
多点电喷 铝 铁 国IV+OBD 宝来 2011 款 1.6L 手 劢舒适型 5挡手劢 5 手劢变速 箱(MT) 宝来 2011 款 1.6L 手 劢舒适型 前置前驱 麦弗逊式 独立悬架 扭力梁式 半独立悬 机械液压 劣力 承载式 宝来 2011 款 1.6L 手 劢舒适型 通风盘式 盘式 手刹
VKFJ键盘操作说明书
Instruction ManualINDEX1 Product Introduction (1)1.1 Package Contents (1)1.2 Main Functions (2)1.3 Specification (3)2 Installation (4)2.1 Dimension (4)2.2 External Connection (5)3 Operation (7)3.1 Keyboard Self-detection (7)3.2 Joystick Operation (8)3.3 Key Operation (9)3.4 Menu Operation on LCD (10)3.4.1 Menu Operation Mode (11)3.4.2 Index of Menu (11)3.5 Menu Operation (12)3.6 Keyboard Short Commands (14)AppendixⅠAnalysis and Solution of Common Problem (15)Copyright Statement (16)1 Product Introduction1.1 Package ContentsKeyboard 1 pc Power supply 1pc 4Pin Line Pressing Terminals 1pc User manual 1pc1.2 Main FunctionsThe address range of PTZ or dome camera or decoder can be set from 0～255. At most, 128 devices can be connected in parallel.All input and output communication ports are lightning protection design and the anti-jamming ability is strong. The standard transmission distance is up to 1.2KM.Control all the functions of PTZ or dome camera, such as on / off of back light compensation.Set and run the preset point of PTZ or dome camera. 255 preset points are settable in all.Run PTZ or dome camera scan at a fixed speed or variable speed.Control PTZ or dome camera manually or automatically. Change factory default setting of special camera by adjusting camera menu.Control zoom, focus and aperture of camera manually.Control multiple PTZ or dome cameras at the same time.Built-in protocols are selectable.Built-in multiple languages OSD.Key sound on/off function.1.3 SpecificationProduct Vector Keyboard Power Supply DC12V+10%/50HZ 500mAOperatingTemperature-20℃～+55℃OperatingHumidity≤90% Non Condensing Communication RS-485Interface 4PIN Line Pressing TerminalsBaud Rate 1200bps, 2400bps, 4800bps, 9600bps, 19200bpsCommunication Protocol PELCO-D, PELCO-P,SAMSUNG,YAAN, SAECommunication between Camera and Keyboard One point to multi-pointsHalf-duplexJoystick Vector variable speed joystick Display LCD CommunicationDistance1.2KmControl CameraQuantity128OSD Menu EnglishDimension 220x130x10(mm)2 InstallationAfter open keyboard package, please keep the original packaging materials, so that when there is a problem, keyboard with original packaging materials can be sent back to the agent or the manufacturer for reparation. Non-original packaging material may lead to an unexpected transit damage, which may cause additional costs.2.1 DimensionFront side of KeyboardBackside of KeyboardPower Supply Interface: Connect to external stable voltage DC12V input through this interface.Communication interface: RS-485 communication interface. Indicator light of power: It shows the present power status. Light on means power connected well.Indicator light of communication interface: When keyboard connect to dome camera or PTZ, this light is on.2.2 External ConnectionPlease read the user manual carefully before any connection. Any wrong connection may cause the device damaged permanently. When you connect the device, please make sure the powers of all devices are off. Communication cable used between the devices connection must be twisted-pair cable with shielding. When cable is set up, high voltage line or other interfering line should be avoided as much as possible. Keyboard cannot be cross-connected when connecting with other communication devices. Anode must be to anode, cathode to cathode. As shown below:below:please make sure the address, protocol, baud rate of thekeyboard is set the same to the dome or PTZ camera. Otherwise, the dome or PTZ camera can’t be controlled.3 Operation3.1 Keyboard Self-detectionFig 3.1.1 Fig 3.1.2After power on, the keyboard take the following actions automatically:A. Self-detecting: The first line of LCD display shows“SYSTEM STARTUP”.The second line shows “<” and “<” increases successively till it fills the screen with one sound “di” as Fig 3.1.1.If sound is turned on, “<” increases successively with sound “di,di…” as Fig 3.1.1.B. After self-detection finishes: Get the current parametersautomatically and clear the contents of the second line onthe LCD display.The first line of LCD display shows “PELCO-D 2400 000”.They are communication protocol, baud rate, addressrespectively as Fig 3.1.2.3.2 Joystick OperationUsing joystick can control PTZ or dome camera’s rotation, pan-tilt direction and speed. Changing the tilt angle of joystick can adjust speed even.Vector joystick dimension is as below:Vector Joystick has three main functions as following:(1) Control dome camera rotation: Rocking the joystick in any direction, camera moves in appropriate direction. At the same time, the LCD displays "PTZ <<<<<". Controlling rocker of rotary speed of inclination can control the speed of the camera. More "<" displays on LCD screen, joystick tilts more, and the speed of camera is faster. Less "<" displays on LCD screen, joystick tilts less, and the speed of camera is slower.(2) Zoom Adjust (special function of 3D keyboard): Rotate the joystick grip to adjust focal length of the lens. Clockwise rotation of Joystick grip, zoom in and the image gets closer and larger; Counterclockwise rotation of joystick grip, zoom out and image gets farther and smaller.While rotating the joystick, the LCD displays "PTZ<<<<<".The number of "<" stands for the speed of zoom. More "<", zoom speed is faster. Less "<", zoom speed is slower.(3). The menu setting of controlled object: When setting menu, joystick up is to select previous menu and joystick down is to select the next menu. Joystick left or right can change parameters of the selected menu (as described in the LCD menu operation).3.3 Key Operation【Focus+】: Manual focus on far object. The far objects come clear and the near objects come blurring.【Focus-】: Manual focus on near object. The near objects come clear and the far objects come blurring.【Zoom+】: Zoom in to enlarge object.【Zoom-】: Zoom out the lens to larger view field. The object becomes smaller.【Iris+】: Increase aperture gradually. The picture becomes brighter.【Iris-】: Downsize aperture. The picture becomes darker. 【Setup】: Set key, [Setup]+number+[Enter] to set the preset point of the camera or set the short commands of thekeyboard(See 3.5).【Preset】: Run key, [Preset]+number+[Enter] to run the presetpoint.【Menu】: Menu key, to enter Menu.【Addr】: Address key, [Addr]+number+[Enter] to choose the communication address.【0】～【9】: Number keys [0], [1], [2], [3], [4], [5], [6], [7], [8], [9]. 【Clear】: Delete key, [Clear]+number+[Enter] to delete the preset point.【Enter】: Confirm key, to confirm the present operation.【Aux ON】: Aux ON.【Aux OFF】: Aux OFF.3.4 Menu Operation on LCDEnter the menu on LCD: Press【Menu】key to enter menu，as Fig 3.4.1.Fig 3.4.1Exit menu on LCD: Select random function keys except 【Menu】key to exit menu and enter corresponding operation. For example, press 【Focus+】to exit menu and enter focus setting. As Fig 3.4.2.Fig 3.4.23.4.1 Menu Operation ModeThere are two modes of menu operation：(1) Joystick operation: Joystick up and down to flip the menu.Joystick left and right + [Enter] to set theparameters of the menu.(2) Key operation: Press [2], [8] to flip the menu.Press [4], [6]+ [Enter] to set the parametersof the menu.Notice: When flipping to address page, [2], [8] can’t flip the menu page, and just function as number keys. [4], [6] can’t set parameters of menu, and just function as number keys.3.4.2 Index of MenuThe above menus are displayed in the second line on LCD. Only one menu is displayed at one time. The display mode is as below (e.g communication address):Menu Setting Range:PROTOCOL: PELCO-P/ PELCO-D/ SAMSUNG/ YAAN/SAELANGUAGE: ENGLISHSOUND: ON/OFFADDRESS: 000 ～255BAUD RATE: 1200/2400/4800/9600/19200 BPS3.5 Menu OperationWhen joystick and keys are operated at the same time, joystick operation is preferred.Rotating the joystick to any direction can exit the present setting page (except on menu page).When setting parameters in menu, pressing [Enter] can make the setting effective. The key [Enter] just store the latestchanged parameters of menu. For example,if you change protocol, address and baud rate in order, then press [Enter]. Only baud rate is changed successfully.When there is nothing in the second line on LCD as Fig3.5.1, number keys [2], [8], [4], [6] can be used as up, down, left and right keys to control PTZ or dome camera left and right rotation as the function of joystick. But the rotation speed is the fastest and no grades to select. Show as 3.5.2 (e.g key [2]).After entering menu, joystick has no function to control PTZ or dome camera. It can only be used as up or down to flip the menu page and left or right to change the parameters of menu. Number keys [0], [1], [3], [5], [7], [9] are invalid. [2], [8], [4], [6] are used as up, down, left and right keys. They are not used as number keys at this time. Their functions are just to flip the menu page but not to control PTZ or dome camera’s up, down, left or right rotation. Only after exiting menu and when there is nothing in the second line on LCD, they can control dome cameras up, down, left and right rotation.When setting [ADDRESS], number keys [0], [1], [3], [5], [7], [9] restore the number keys’ function. [2], [8], [4], [6] restore thenumber keys’ function and don’t have up, down, left and right functions.When pressing [Enter] after address setting on menu finishes, it will enter baud rate setting [BAUD RATE 2400]. When go back to [ADDRESS] again, the menu interface displays [ADDRESS 000]. The present set value can’t be seen. When exit menu, the first line on LCD displays the present communication address. Joystick up or down can exit address setting.Address range is 000-255. The number above 255 can’t be set.3.6 Keyboard Short CommandsCombination key: [Setup]+number+[Enter]Number Function700 Turn off sound701 Turn on sound812 Set baud rate to 1200bps824 Set baud rate to 2400bps848 Set baud rate to 4800bps896 Set baud rate to 9600bps819 Set baud rate to 19200bpsAppendixⅠ Analysis and Solution of Common ProblemIssue PossibleReasonSolutionCheck power cable connectionand connect it wellNothing onLCD after item is turnedon No powerMake sure power is DC12V Protocol iswrongCheck protocol of keyboard.Make sure it is the same to thedome or PTZ camera.Baud rateis wrongCheck baud rate of keyboard.Make sure it is the same to thedome or PTZ camera.Can’t control the target dome cameraAddress is wrongCheck address of keyboard. Make sure it is the same to the dome or PTZ camera.Notice: The above solutions of common issues are just for your reference. If there are some special issues, please contact your dealer to get technical support.Copyright StatementThis copyright merely belongs to the manufacturer. Without permission, please don’t plagiarize or copy the contents of this book in any form or by any means.The company follows the policy of continuous development. Therefore, the company reserves the right to modify or improve the products described in this manual without notice.The content of manual is offered according to the "current state". Unless applicable law specified, otherwise the company does not make any kind of clear or tacit assurance about the accuracy, reliability and contents of this manual. The company reserves the right to revise or recoup this manual at any time without notice.Distributed by :Challenger Security Products10 Sandersons Way Marton Blackpool FY4 4NBGeneral Enquiries : e.mail: ***********************.uk - web: Sales Tel No : 01253 791 888 Fax No : 01253 791887 Technical No : 01253 792898VKFJ V2。
精选2011卡宴低配配置表 90.8万
谨致，
保时捷Internet 团队
您个人的Cayenne
技术数据
发动机 发动机布置形式 气缸数 排量 功率
前置 6 2,995 cm³ 245 kW (333 hp)
页码 1 19.02.2011汽车配置
技术数据 (续) 对应转速 最大扭矩 对应转速 压缩比
变速箱 驱动形式
手动变速箱 自动变速箱 自动变速箱类型
车身 • 全电镀单壳体车身 • 4 个带一体式侧撞保护梁的车门 • 与车身同色的涂漆门把手 • 顶部铰接式尾门 • 带整体式进气口的前裙板• 涂与车身同色漆的侧进气口板条 • 两根涂暗银色漆的单管尾管(左/右) • 全部为有色隔热玻璃，挡风玻璃上带有灰色遮光色带 • 100升的油箱 • 发动机盖上的强劲拱顶 • 尾门上带有镀铬保时捷标志和车型名称标志 • 电动可倾/滑动式玻璃天窗 • 前后部停车辅助 • 自动尾门 • 私密玻璃
订购号：
A1 MA C1Q 7K4 H9M
PE6
个性化配置
纯黑 标准黑色内饰 18英寸Cayenne S II 车轮 轮胎气压监控系统（TMS） 用于18 英寸合金车轮的全天候 轮胎 带记忆组件的18向自适应运动 型座椅
价格*
0￥ 0￥ 6,000 ￥ 10,800 ￥ 0￥
Tadano GTC-2000 200 吨最大吊卸机型号说明书
1-877-MAX-LIFTGTC-20001-877-MAX-LIFTMarch 2022. Unless otherwise specified, all information in this brochure refers to a standard crane equipment, and it is intended as general information only. No liability is assumed. Errors reserved. Product specifications and prices are subject to changes without notice. The p hotographs and/or drawings in this brochure are for illustrative purposes only. For correct and safe crane operation, the original operating manual and lifting capacity charts are essential. Failure to follow the corresponding Operator’s Manual when using our equipment or f ailure to otherwise act responsibly may result in property damage, serious injury or death. The sole warranty applicable with respect to oure quipment is the standard warranty as per general terms and conditions of sales and service (ask your local Tadano dealer for details), and Tadano makes no other warranty, express or implied. All rights reserved. Any use of the trademarks, logos, brand names and model names used herein is prohibited.© Tadano Ltd. 20222 | GTC-2000Contents7 Specifications (8)9 Transportation...............................................................................................................................10-12 Transport variants .. (13)15 Speeds and gradeability (16)Main boom (17)Slewing (17)Hoist (17)Hook Blocks (17)HA: Main boom .............................................................................................................................18-53 HAV: Folding swing-away jib ..............................................................................................................54-121 HAV-HY: Hydraulic swing-away jib .......................................................................................................122-188 Notes to Lifting Capacity . (189)191 Basic machine ..............................................................................................................................192-193 Optional Equipment (non-exhaustive) . (194)GTC-2000| 34 | GTC-2000 CounterweightT rackR adiusM ain boomF olding swing-away jibH ydraulic swing-away jibR oll/list angleW ind speed in ft /s (feet per second)T rack shoeH ook blockH oist 1H oist 2T ravel speedG radeabilityS lewingB oom telescoping B oom elevationW orking speedsM ax. line pull R ope diameter R ope length H ook block (capacity-sheaves-rope diameter) N umber of lines P ossible load of hook block N umber of sheaves in boom head D istance head sheave axle – hook ground W eight of hook blockGTC-2000 | 5T rack leftT rack rightE xtension beamB ase craneC entral ballastT ruck pay loadC ounterweight base plateC ounterweight plateA ssembly weightT ransport variantHighlights196.9 ft pinned boom; 16.4 ft to 75.5 ft jib (tiltable from 0° to 36°)Lifting capacities up to 4° roll/list angle, all …Pick & Carry“, jib capacities up to 1° roll/list angle Double hook operation with rooster sheave or jibPowerful hoists with 1.02 in. rope (30,640 lb pull / 456 ft/min. speed)Powerful, robust and versatile undercarriage with smart and comprehensive access concept Fully self rigging operationRemote control for all rigging and operating functionsBest in class traction force (326,000 lbf)6 | GTC-2000Specifications8 | GTC-2000Transportation* 107,990 lb with Hyd Jib / 107,660 lb with Mech Jib10 | GTC-2000GTC-2000| 1140,800 lb*12 | GTC-2000* Hydraulic version1,010 lb1,900 lb 1,040 lb 1,650 lb / 1,980 lb*5,070 lb16,540 lb16,540 lb1 x 11,025 lb4 x 22,050 lb** 2-bar shoeGTC-2000| 13Notes14 | GTC-200016 | GTC-2000GTC-2000 | 17* Heavy lift sheave required** Heavy lift sheave and 7 sheaves hook block requiredHook BlocksSlewing1,6 rpm18 | GTC-2000+ 33,100 lb**Heavy lift sheave and 7 sheaves hook block required*** Max. crane capacity – with additional special equipment**** over front/rear1)C apacities with horizontal boomGTC-2000| 19+ 33,100 lb126.0 ft20 | GTC-2000+ 33,100 lb**Heavy lift sheave and 7 sheaves hook block required 1)C apacities with horizontal boom+ 33,100 lb126.0 ft+ 33,100 lb**Heavy lift sheave and 7 sheaves hook block required 1)C apacities with horizontal boom+ 33,100 lb126.0 ft+ 33,100 lb**Heavy lift sheave and 7 sheaves hook block required 1)C apacities with horizontal boom+ 33,100 lb126.0 ft+ 33,100 lb**Heavy lift sheave and 7 sheaves hook block required 1)C apacities with horizontal boom+ 33,100 lb126.0 ft+ 33,100 lb1)C apacities with horizontal boom+ 33,100 lb+ 33,100 lb**Heavy lift sheave and 7 sheaves hook block required 1)C apacities with horizontal boom+ 33,100 lb126.0 ft+ 33,100 lb1)C apacities with horizontal boom+ 33,100 lb126.0 ft+ 33,100 lb1)C apacities with horizontal boom+ 33,100 lb126.0 ft+ 33,100 lb1)C apacities with horizontal boom+ 33,100 lb126.0 ft+ 33,100 lb1)C apacities with horizontal boom+ 33,100 lb126.0 ft+ 33,100 lb+ 33,100 lb+ 33,100 lb+ 33,100 lb126.0 ft+ 33,100 lb+ 33,100 lb126.0 ft+ 33,100 lb+ 33,100 lb126.0 ft+ 33,100 lb+ 33,100 lb126.0 ft。
捷安特2011款ATX770与770-D山地车对比
770770-d
车架铝合金A6061车架铝合金A6061车架
前叉TWINS三代T避震前叉（铝合金外管）TWINS三代MLO机械锁死避震前叉（铝合金外管）前变FD-M412FD-M412
后变RD-MC410RD-MC410
变把ST-M410ST-M410
大齿盘22/32/42齿铝合金（普通）FC-M361 22/32/42
齿飞轮11-3211-32
24速24速
刹车系统AVID SDG 高效V型刹车BR-M416A机械碟刹
座垫WTB PURE V座垫WTB PURE V座垫
轮圈GIANT 26X1.5 双层车圈GIANT 26X1.5 双层铝合金车圈
轮胎正新MAVERICK 26X1.9 TPI 60城市山地车正新MAVERICK26X1.9 TPI 60城市山地车轮胎
把31.8小燕把31.8平把
竖杆铝合金铝合金
座垫杆铝合金座垫杆铝合金座垫杆
无小副把
车首零件1-1/8（UP）至1-1/4（DOWN）1-1/8（UP）至1-1/4（DOWN
总结：前叉不能锁死，没有碟刹，燕把，没有副把，其他都一样
黄色部分为区别。
MT41K256M16TW-107 IT_P
Mode RegistersMode registers (MR0–MR3) are used to define various modes of programmable opera-tions of the DDR3 SDRAM. A mode register is programmed via the mode register set (MRS) command during initialization, and it retains the stored information (except for MR0[8], which is self-clearing) until it is reprogrammed, RESET# goes LOW, the device loses power.Contents of a mode register can be altered by re-executing the MRS command. Even if the user wants to modify only a subset of the mode register’s variables, all variables must be programmed when the MRS command is issued. Reprogramming the mode register will not alter the contents of the memory array, provided it is performed cor-rectly.The MRS command can only be issued (or re-issued) when all banks are idle and in the precharged state (t RP is satisfied and no data bursts are in progress). After an MRS com-mand has been issued, two parameters must be satisfied: t MRD and t MOD. The control-ler must wait t MRD before initiating any subsequent MRS commands.Figure 52: MRS to MRS Command Timing (t MRD)CK#CKCommandAddress CKE 3Don’t CareIndicates break in time scale质量等级领域:宇航级IC 、特军级IC 、超军级IC 、普军级IC 、禁运IC 、工业级IC ，军级二三极管，功率管等;应用领域:航空航天、船舶、汽车电子、军用计算机、铁路、医疗电子、通信网络、电力工业以及大型工业设备祝您:工作顺利，生活愉快!以深圳市美光存储技术有限公司提供的参数为例，以下为MT41K256M16TW-107 IT_P的详细参数，仅供参考ing location within the block. The programmed burst length applies to both READ and WRITE bursts.Figure 54: Mode Register 0 (MR0) DefinitionsAddress busMode Register 1 (MR1)The mode register 1 (MR1) controls additional functions and features not available inthe other mode registers: Q OFF (OUTPUT DISABLE), TDQS (for the x8 configurationonly), DLL ENABLE/DLL DISABLE, R TT,nom value (ODT), WRITE LEVELING, POSTEDCAS ADDITIVE latency, and OUTPUT DRIVE STRENGTH. These functions are control-led via the bits shown in Figure 56 (page 146). The MR1 register is programmed via theMRS command and retains the stored information until it is reprogrammed, until RE-SET# goes LOW, or until the device loses power. Reprogramming the MR1 register willnot alter the contents of the memory array, provided it is performed correctly.The MR1 register must be loaded when all banks are idle and no bursts are in progress.The controller must satisfy the specified timing parameters t MRD and t MOD before ini-tiating a subsequent operation.Figure 56: Mode Register 1 (MR1) DefinitionAddress busNotes: 1.MR1[18, 15:13, 10, 8] are reserved for future use and must be programmed to 0.2.During write leveling, if MR1[7] and MR1[12] are 1, then all R TT,nom values are availablefor use.3.During write leveling, if MR1[7] is a 1, but MR1[12] is a 0, then only R TT,nom write valuesare available for use.DLL Enable/DLL DisableThe DLL may be enabled or disabled by programming MR1[0] during the LOAD MODEcommand, as shown in Figure 56 (page 146). The DLL must be enabled for normal oper-ation. DLL enable is required during power-up initialization and upon returning to nor-mal operation after having disabled the DLL for the purpose of debugging or evalua-tion. Enabling the DLL should always be followed by resetting the DLL using the appro-priate LOAD MODE command.If the DLL is enabled prior to entering self refresh mode, the DLL is automatically disa-bled when entering SELF REFRESH operation and is automatically re-enabled and resetupon exit of SELF REFRESH operation. If the DLL is disabled prior to entering self re-fresh mode, the DLL remains disabled even upon exit of SELF REFRESH operation until it is re-enabled and reset.The DRAM is not tested to check—nor does Micron warrant compliance with—normal mode timings or functionality when the DLL is disabled. An attempt has been made to have the DRAM operate in the normal mode where reasonably possible when the DLL has been disabled; however, by industry standard, a few known exceptions are defined:•ODT is not allowed to be used•The output data is no longer edge-aligned to the clock•CL and CWL can only be six clocksWhen the DLL is disabled, timing and functionality can vary from the normal operation specifications when the DLL is enabled (see DLL Disable Mode (page 125)). Disabling the DLL also implies the need to change the clock frequency (see Input Clock Frequen-cy Change (page 129)).SDRAM configuration only and must be disabled via the mode register for the x4 andx16 configurations.On-Die TerminationODT resistance R TT,nom is defined by MR1[9, 6, 2] (see Figure 56 (page 146)). The R TTtermination value applies to the DQ, DM, DQS, DQS#, and TDQS, TDQS# balls. DDR3supports multiple R TT termination values based on RZQ/n where n can be 2, 4, 6, 8, or12 and RZQ is 240ȍ.Unlike DDR2, DDR3 ODT must be turned off prior to reading data out and must remainoff during a READ burst. R TT,nom termination is allowed any time after the DRAM is ini-tialized, calibrated, and not performing read access, or when it is not in self refreshmode. Additionally, write accesses with dynamic ODT (R TT(WR)) enabled temporarily re-places R TT,nom with R TT(WR).The actual effective termination, R TT(EFF), may be different from the R TT targeted due tononlinearity of the termination. For R TT(EFF) values and calculations (see On-Die Termi-nation (ODT) (page 197)).The ODT feature is designed to improve signal integrity of the memory channel by ena-bling the DDR3 SDRAM controller to independently turn on/off ODT for any or all devi-ces. The ODT input control pin is used to determine when R TT is turned on (ODTL on)and off (ODTL off), assuming ODT has been enabled via MR1[9, 6, 2].Timings for ODT are detailed in On-Die Termination (ODT) (page 197).WRITE LEVELINGThe WRITE LEVELING function is enabled by MR1[7], as shown in Figure 56 (page 146).Write leveling is used (during initialization) to deskew the DQS strobe to clock offset asa result of fly-by topology designs. For better signal integrity, DDR3 SDRAM memorymodules adopted fly-by topology for the commands, addresses, control signals, andclocks.The fly-by topology benefits from a reduced number of stubs and their lengths. Howev-er, fly-by topology induces flight time skews between the clock and DQS strobe (andDQ) at each DRAM on the DIMM. Controllers will have a difficult time maintainingt DQSS, t DSS, and t DSH specifications without supporting write leveling in systemswhich use fly-by topology-based modules. Write leveling timing and detailed operationinformation is provided in Write Leveling (page 131).POSTED CAS ADDITIVE LatencyPOSTED CAS ADDITIVE latency (AL) is supported to make the command and data busefficient for sustainable bandwidths in DDR3 SDRAM. MR1[4, 3] define the value of AL,as shown in Figure 57 (page 149). MR1[4, 3] enable the user to program the DDR3SDRAM with AL = 0, CL - 1, or CL - 2.。
2011款途锐舒适版刷原车蓝牙
2011款途锐舒适版成功刷出原车蓝牙方法现介绍具体步骤如下：1，准备一根VCDS 10.63（本人用的是10.64）检测线及软件中文版（价格120.00左右）。
2，安装好软件后，先将线一端插入车驾驶席左脚上方的检测口（粉红色），另一端插入电脑USB口。
3，启动VCDS软件，选择“自动检测”-“选择模块”－“电子设备2”－“5f电子信息系统”－“匹配”。
4，通道选择06，将数值改为1保存退出。
5，重启RNS850（同时按下“PHONE”+“CLIMATE”+“NA V”+“TIAFFIC”+中间按钮）。
6，先按“CAR”，显示导航画面，先按“SETUP”不放，再按“CAR”,几秒后即显示绿色英文菜单（系统底层菜单）。
7，用中间旋钮选择到“diagnose”（在最下面一行）上，按一下中间旋钮确定，屏幕进入子菜单，然后按相同方法选择“settings”，进入子菜单，选择“AMI/AUX”确定后，旋转中间按钮来调整其值为[AUX/AMI BT/AMI]1/8确定，然后同样方法，选择“Tel Settings Misc”调整其值为3。
8，重启RNS850。
9，启动VCDS软件，选择“自动检测”-“选择模块”－“电子设备２”－“5f电子信息系统”－“匹配”。
10，通道选择17，将数值2改为1，保存退出。
11，设置完，重启RNS850。
12，完成以上步骤就可以拔掉VCDS线，关掉电脑。
13，新开机，按下“PHONE”，即显示蓝牙设置界面，按照界面设置即可。
进入系统底层菜单（英文绿菜单），用中间旋钮选择到“diagnose”上并按一下中间旋钮确定，屏幕进入子菜单，然后按相同方法选“settings”，进入子菜单，选择“imported multimedia”确定后再旋转中间按钮来选择其值为 [Copy/Ripping]确定。
2011途锐舒适版成功刷出原车蓝牙方法在总结了网友的检验上，本人刷出了蓝牙功能，步骤如下：1，需要一根VCDS 10.63（本人用的是10.64）线及软件中文版（价格120.00左右）。
BMW2011年新款自行车介绍
BMW Lifestyle
Bikes & Equipure
2011年款BMW越野山地自行车 珍珠白色
车架
无论在沥青路面上还是颠簸的山林地带 – 这款运动型全避震山地 自行车都会无往不利，与您恒久相伴。同时，它也传承了BMW 的经典特色：独一无二，不容混淆。
前叉 车把 竖杆 曲柄组 车闸 车圈 轮胎 变速系统 后变速器 前变速器 指拨/闸把 链盒 链条 车座 脚踏 重量 车架尺寸 附加装备： 订购号
BMW Lifestyle
Bikes & Equipment
Sheer Driving Pleasure
2011年款BMW休闲自行车 白色/蓝色
这款休闲自行车是享受惬意两轮生活的绝佳选择。今天，驾车 沿着海滩小路度过一个悠闲的夜晚。明天，在户外享受一次亲 近自然的驾乘之旅。自由行程，任您选择。
前叉 减震器 车把 竖杆 曲柄组 车闸 车轮组件 轮胎 变速系统 后变速器 前变速器 变速手柄 链盒 链条 车座 脚踏 重量 车架尺寸 订购号
BMW Lifestyle
Bikes & Equipment
Sheer Driving Pleasure
2011年款BMW全地形山地自行车 白色/绿色高光
这款极其时尚的越野自行车无疑会带来十足的乐趣。无论是随 意骑行还是在平缓的斜坡上骑行 – 您可以决定将要面对的下一 个挑战。
车架 前叉 减震器 车把 竖杆
铝制，全避震，带4支点后避震器，带一体式BMW标志的BMW设计以及 BMW图形风格，白色/绿色高光 Fox Talas 32 RL避震前叉，行程150 mm Fox RP2 BV，行程145 mm Syntace Duraflite MTB Lowriser Syntace F 149 Force Shimano FC-M552，170 mm摇臂 Shimano Deore XT盘式车闸，180/180 mm DT Swiss E530车圈 Continental Mountain King 2.4 英寸 Supersonic Shimano XT 30速变速器系统 Shimano Deore XT Shimano XT FD-M770-E Shimano XT Shimano XT，11–36齿，10速 Shimano HG74 ‚ fi zi:k Nisene Sport，黑色/绿色 带棘轮机构的Wellgo双重功能脚踏 14.8 kg M（45 cm），L（50 cm） （M）80 91 2 186 343 （L） 80 91 2 186 344
极速传说 2011款奔驰CL级
控制 在４ ５ｓ８。ＡＭＧ车型部分 ，同样有’ ． ｔ 的发动 机版本供应 ，包括搭载５５ Ｌ ． 双涡｛ 机的ＣＬ ３ ＡＭＧ，以及最 大功 率和最 大ｊ ６
别 达 ￣４ ６ｋ 和 ９ ９Ｎ ・ 的ＣＬ ５ＡＭ Ｇ １ ５ Ｗ Ｊ ９ ｍ ６ 在 安 全 配 置 方 面 ，ＡＬ Ａ主 动 式 车 ｉ Ｋ
压 发动机 ，最大功率和最大转矩 分别达蛰 和７ ０Ｎ・ｍ，并可让ＣＬ ５ 在４９Ｓ ０ ５ ０ ． 内完
ｋ ｈ 加 速 ：一 台最 大 功 率 ３ ５ ｋ 、 ｊ ｍ／ 的 ７ Ｗ ８ ９Ｎ ・ｍ的 ５５ＬＶｌ 双 涡 轮 增 压 发 动 机 ２ ． ２ ＣＬ ０ 车 型 上 ， 这使 它 的０～１ ０ｋ ｈ ： ６０ ０ ｍ／的
助、ＡＢ Ａ主动 式盲 点侦 测和 ＮＶ 夜 Ｓ ＡＰ
多 项 安 全 系统 也 是 老 款 ＣＬ 所 不 具 备 的 级 Ｓ Ｅ 安 全 防 护 系 统 的升 级 可 使 车 辆 在 ＡＦ 预
完成制 动的 自动介入 ，保护车辆 和行人 ｆ
全。车 内的 多媒体 系统则 以奔驰标志的Ｃ
系统 为 中心 ，集 合 了全 新的３Ｄ地 图卫 ｌ Ｄ ＶＤ，７２ 硬盘 、声控 系统及 多重视ቤተ መጻሕፍቲ ባይዱ ．ＧＢ 统 ，全面提升 了舒适便利性。
２ １ 款奔驰 Ｃ 级 ０ １ Ｌ
奔 驰 选在 英 国 “ ｏ ｄ ｏ 速 度 节 ” Ｇ ｏ ｗｏ ｄ 上
改款ＣＬ 级。虽然被 称为小改款， 它的改 但 少的。而敢在 “ 速度节”上亮相，它的动力
不可 小觑 。 小 改 款 ＣＬ 最 大 的 变 动 在 于 它 的 ｊ 级 Ｃ ５ ０４ ｔ 车 型 上 搭 载 了新 款 ４６Ｌ Ｌ ５ Ｍａｉ ｃ ． Ｖ８
2011 Honda Civic Sedan技术参考指南说明书
T E C H N O L O G YR E F E R E N C EG U I D E w w w.o w n e r s.h o n d a.c o m2011CIVIC SEDANBluetooth ®HandsFreeLink ®(HFL)(if equipped)...............................................16iPod ®or USB Flash Memory Device (19)PC Card (models with navigation)......................................................................20Owner Link..............................................................................................................21BLUETOOTH ®HANDSFREELINK ®p.16VOICE RECOGNITION p.8INSTRUMENT PANEL p.4AUDIO p.19NAVIGATION p.14Programmable Auto Door AUTO DOOR UNLOCKWhen you turn the ignition OFF When you shift into ParkWhen you turn the ignition OFF When you shift into ParkOperate manuallyAUTO DOOR LOCKWhen you reach 10mphWhen you shift out of ParkOperate manuallyT urn the ignition switch to ON (II).4.Within 5seconds,turn the ignition switch to LOCK (0).three clicks.Malfunction IndicatorsIf an indicator remains on,there may be a problem;see your dealerOn/Off IndicatorsPASSENGER AIRBAGOFF PASSENGER AIRBAG OFF(above Hazard Warning button)1st detent:parking lights on2nd detent:headlights onCharging system Low brake fluid ABS(anti-lock brake system) DRL(daytime running lights)WhenT o toggle between the differentdisplays,press and release theWhat to DoKey Functions by Voice CommandA U D I Op.13N A V I G A T I O Np.14B L U E T O O T H ®H A N D S F R E E L I N K ®p.16Control three different systems with the steering wheel buttons and the ceiling microphone.Voice Command Tips-Press and release the HFL or Navi T alk button,wait for a beep,then give a command.-For a list of available HFL commands,press and release the HFL T alk button and say “Hands-free help.”-For a list of available navigation commands,press and release the Navi T alk button and say “Help.”-Speak in a clear,natural voice.-Reduce all background noise.-Adjust the dashboard and side vents away from the microphone in the ceiling.-Close the windows.HFL T alk button:Give HFL commands or answer incoming calls.Navi T alk button:Give navigation,audio,and climate control commands.Navi Back button:Cancel a command or return to the previous screen.HFL Back button:End a call,go back to the previous command,or cancel an operation.Press and release the Navi T alk button before you give a command. Get Navigation Route InformationAfter a destination is entered,say“How far to destination?”tohear the remaining distance.Say“Display entire route”to seethe routing method the systemmapped for your destination.A list of the nearest ATMs in your area is displayed by shortest distance to destination.destination you want to select.The system calculates the route and displays the “Calculate route to”screen. Say“OK”to set the route.A list of street names appears.The system calculates the routeReceiving a Callbutton:Give HFLanswer incoming calls.button:End a call,go back previous command,or cancel an and release the HFL T alk button before you give a command.“Pair.”3.HFL gives you a four-digit code and begins to search for your phone.4.Search for a HandsFreeLink device from your phone,and connect to HFL.6.HFL asks you to name the phone.For example,say “Mary’s phone.”5.Enter the four-digit code on your phone when prompted.and say “Call”or “Dial”and the desired phone number.2.Press the HFL T alk button,and say “Call”or “Dial”to continue.through the vehicle’s speakers.accept the call.3.Press the HFL Back button to end or decline the call.appears on the screen.2.Say “Store.”and then the phone number.4.T o call a contact once an entry is stored,say “Call Mike.”Cellular Phonebook*(models with navigation)1.Say “Display Information”and “Cellular Phone.”*not available on all phones2.Say “Import Cellular Phonebook.”3.HFL begins to import your contacts to the system.4.T o call a contact,say “Search Imported Phonebook”and select the name and number.the center console.Push AUX or touch the USB icon to begin playing.without navigationwith navigationConnect the USB connector to your iPod dock connector or flash drive.iPod is a registered trademark with navigationpress CLOSE.CLOSE ButtonPC card slotPress AUDIO to show the audiodisplay.Press the | and |buttons to skip through tracks on the card.。
SLIK Carbon Fiber Tripod PRO 923CF PRO 924CF 操作指南说
Please do not use an optional Clamp Head for a carbon fiber tripod. The pipe may be damaged.
To change the angle of each leg, close the Leg slightly, and then pull the Leg angle adjustment lock out. There is a choice of two other angle positions. After choosing the desired leg angle, securely push in the Adjustment lock.
Please tighten the Center column stopper before lifting your hand from the Crank handle. Unexpected fall of the Center column can be prevented.
Please use the Crank handle of the Center column in the height to about 2/3 as the maximum. If not, it may cause unwanted camera movement.
Base plate Pan head attachment screw (1/4") PRO 923CF
Accessory
Leg lock nut 2-way Leg tips
Pan Head Attachment Screw
Prohibition
Allen wrench
RCI NEXT DK 1 的用户手册说明书
Opsætning af fieldbus modul
Ethernet IP 1 DHCP
DHCP aktiveret = IP & Subnet Mask adresse tildeles automatisk af DHCP netværksserver.
anzeige
2 Konfig. info 3 Konfig. Liste 4 Bestätigung der Konfigurationsdatei
Automatische Back-up-Datei (BACKUP.txt) auf der Konfigurationskarte beim Wechseln der Konfigurationsdatei speichern.
2 Setup des Fieldbus-Moduls (je nach Typ des Fieldbus-Modch Typ des Fieldbus-Moduls)
QUICKGUIDE RCI NEXT
DE
Wahl der Konfigurationsdatei
QUICKGUIDE RCI NEXT
DK
RCI menu
1 2 3
Valg af konfigurationsfil
1 2
3 4
1 Valg af konfigurationsfil
Indsæt konfigurationskort i SD kortlæser inden valg af konfigurationsfil.
kb建滔型号 -回复
kb建滔型号-回复小编非常高兴收到您的写作请求。
下面我将一步一步回答关于[kb建滔型号]的问题，并为您提供一篇关于该型号的1500-2000字的文章。
[kb建滔型号]是一款新型号的键盘，它在设计和功能上有一些独特之处。
在本文中，我们将深入研究这款键盘的特点，解释其工作原理，并讨论其在各种应用场景中的潜在优势。
首先，让我们来看看[kb建滔型号]在外观设计方面有何独到之处。
这款键盘采用了一种时尚而流线型的外观设计，简洁大方，给人一种高质感和专业感。
它的按键布局经过精心设计，使得用户在使用时更加舒适和高效。
键帽的材质采用了高硬度的ABS塑料，能够有效地抵抗长时间使用和磨损。
除了外观设计，[kb建滔型号]在功能上也十分出众。
首先，它拥有多种连接方式，包括蓝牙、USB有线和无线连接，能够满足不同用户的需求。
其次，该键盘配备了背光功能，用户可以根据自己的喜好和环境情况调节按键的亮度和颜色。
此外，[kb建滔型号]还具备多媒体控制功能，用户可以轻松控制音量、播放/暂停音乐等，大大提高了使用的便利性。
在解释完[kb建滔型号]的设计特点之后，让我们来探讨一下它的工作原理。
首先，该键盘采用了先进的蓝牙技术，可以与各种不同的设备进行稳定无障碍的连接。
其次，键盘内部的电路设计精巧，确保了按键的灵敏度和稳定性。
另外，[kb建滔型号]还配备了一块高性能的芯片，可以实时处理用户输入的数据，并将其传输给相应的设备。
除了在设计和功能方面的优势，[kb建滔型号]在各种应用场景中也有着广泛的潜在优势。
无论是在办公室还是在家庭环境中，[kb建滔型号]都能够提供出色的输入体验。
其舒适、高效的按键设计使得用户在长时间的输入操作中感到轻松自如，大大减少了手部疲劳。
此外，多种连接方式的支持，使得该键盘能够在不同设备之间快速切换，提高了工作效率。
综上所述，[kb建滔型号]是一款具有独特设计和出色功能的键盘。
无论是外观设计、功能特点还是工作原理，都体现出了创新和实用。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
毛概试题项选择题（每题1分，共15分）1、全面贯彻“三个代表”重要思想的关键在（A ）A、坚持与时俱进B、坚持党的先进性C、坚持执政为民D、坚持党的领导2、邓小平理论的精髓是（ B）A、解放生产力 , 发展生产力B、解放思想 , 实事求是C、坚持四项基本原则D、“三个有利于”标准3、消灭剥削的物质前提是（B ）A、实行公有制B、生产力的高度发达C、实行人民民主专政D、实行按劳分配4、我国社会主义初级阶段的时间是指（ B）A、中华人民共和国成立到社会主义现代化基本实现B、社会主义改造基本完成到社会主义现代化基本实现C、中华人民共和国成立到社会主义改造基本完成D、社会主义改造基本完成到共产主义社会5、坚持党的基本路线一百年不动摇的关键是（A ）A、坚持以经济建设为中心不动摇B、坚持“两手抓 , 两手都要硬”的方针不动摇C、坚持四项基本原则不动摇D、坚持改革开放不动摇6、我国社会主义建设的战略目标是（ D）A、实现农业、工业、国防和科学技术现代化B、实现工业化、社会化、市场化、和现代化C、实现政治、经济和文化的现代化D、把我国建设成为富强、民主、文明的社会主义现代化国家7、我国的工业化任务还没有完成，总体上看，现在还处于（ C）A、农业社会B、现代化工业社会C、工业化中期阶段D、工业化高级阶段8、实现全面建设小康社会的目标重点和难点在（ D）A、大城市B、中等城市C、小城镇D、农村9、实行以家庭承包经营为基础、统分结合的双层经营体制，是党在农村的基本政策，必须长期坚持。
稳定和完善这一双层经营体制的关键和核心是（A ）A、稳定和完善土地承包关系B、完善农村所有制结构C、尊重农民的首创精神D、发展规模经济10、改革开放以来，对社会主义可以实行市场经济在理论认识上重大突破是（D ）A、市场经济是法治经济B、市场对资源配置起基础性作用C、市场经济是国家宏观调控的经济D、市场经济不属于社会基本制度的范畴11、社会主义市场经济条件下，市场机制（A ）A、对资源配置起基础性作用B、能确保经济总量的平衡C、可以实现经济结构的平衡D、可以保障社会公平12、私营经济中的劳动者的收入属于（ C）A、按劳分配收入B、按资分配C、按劳动力价值分配D、按经营分配13、人民民主是社会主义的本质要求和内在属性 ,归根到底是（A ）A. 是社会主义公有制经济在政治上的集中体现B、有利于调动最广大人民群众的积极性C、是社会主义制度优越性的重要体现D、体现了多数人对少数人的专政14、在下列收入中属于按劳分配性质的收入是（B ）A、个体劳动者的劳动收入B、集体企业职工的工资收入C、股份制企业职工的按股分红收入D、国有企业工程师业余帮助乡镇企业搞设计获得的收入15、社会主义精神文明建设的基本内容是（ B）A、培育和弘扬民族精神及培育“四有”公民B、加强思想道德建设，发展教育科学文化C、加强马列主义、毛泽东思想、邓小平理论教育D、坚持党的基本路线和基本方针二、多项选择题（每题2分，共20分）1、党的十五大指出邓小平理论是马克思主义在中国发展的新阶段，其基本依据是(ABDE )A、开拓了马克思主义的新境界B、提出了新的世界观和方法论C、把对社会主义的认识提高到新的科学水平D、对当今时代特征和总体国际局势做出新的科学判断E、形成了新的建设中国特色社会主义理论的科学体系2、“三个有利于”判断标准是（ABC ）A. 生产力标准的深化B. 实践标准与真理标准的统一C. 实践标准在社会领域的深化和具体化D. 解放思想，实事求是的统一E. 四项基本原则的具体统一3、社会主义按劳分配的必然性是：（ABC ）A. 社会主义生产资料公有制是实行按劳分配的前提条件B. 社会主义生产力发展水平是实行按劳分配的物质条件C. 劳动还存在着种大差别，劳动还是谋生的手段，是实行按劳分配的直接原因D. 多种所有制经济存在是根本原因E. 社会主义市场经济的发展是直接原因4、确立社会主义根本任务的依据是（ ABCD）A、生产力是社会发展的最根本的决定性因素B、社会主义本质决定的C、解决社会主义初级阶段主要矛盾的要求D、体现社会主义制度优越性的基本条件E、适应当今世界“和平与发展”时代的要求5、邓小平指出“改革是中国的第二次革命”，其含义是指（BCDE ）A、改革与第一次革命具有相同的内容B、改革也是解放生产力C、改革是对原有经济体制的根本性变革D、改革引起了社会生活的深刻变化E、改革是社会主义发展的直接动力6、我国经济社会发展战略的特点是(ABCD)A、既具有雄心壮志，又坚持实事求是B、注重社会全面协调发展C、以提高人民生活水平为出发点和归宿点D、体现了社会主义制度的优越性E、是赶超发达国家的发展战略7、社会主义市场经济体制（ABC ）A、是我国经济体制改革的目标B、是同社会主义基本制度结合在一起的C、是市场在社会主义国家宏观调控下对资源配置起基础性作用的经济体制D、是同资本主义市场经济完全相同的E、是市场对社会经济完全起作用的8、中国外交政策的主要目标是（AB）A、反对霸权主义 , 维护世界和平B、增强国际合作 , 促进共同发展C、坚持独立自主D、和平共处E、加强同第三世界的团结与合作9、社会变革中出现的社会阶层包括（ABCDE ）A、民营科技企业的创业人员和技术人员B、受聘于外资企业的管理人员和技术人员C、个体户、私营企业主D、中介组织的从业人员E、自由职业人员10、在新的历史时期，党面临的两大历史性课题是（AE ）A、提高党的领导水平和执政水平B、建立市场经济体制C、国企改革D、防止西方和平演变E、提高拒腐防变和抵御风险能力试卷八(主观题及答案)三、辨析题（第一道题七分，第二道题八分，共15分）1、随着改革开放的深入进行，我国所有制结构发生了重大变化，非公有制经济比重有所增加，公有制经济的比重有所减少。
这势必会影响我国社会主义的性质。
2、社会主义市场经济是法制经济，因此，在市场经济中人们的经济行为可以不受道德规范。
四、分析论述题（每题10分共20分）1、结合邓小平理论形成的社会历史条件说明任何理论的形成都不是一蹴而就的。
2、请根据我国社会主义初级阶段的基本特征分析我国社会主义初级阶段为什么至少需要上百年时间。
五、材料题（10分）：在伊春市，有一片郁郁葱葱的“马永顺林”，这是一位“伐木英雄”在垂暮之年栽下的。
林业工人马永顺一生伐木3万多棵，获得奖状和勋章无数，这曾是他最大的骄傲。
可是，到了晚年，望着门前的荒山秃岭，他涌起了一种负疚感。
于是，他开始偿还“绿债”，成为新时期的“植树英雄”。
如今，我国大多数林业工人都与马永顺一样，放下油锯和斧头，走进了造林护林的行列。
从“乱砍乱伐”到“封山育林”，从“毁林开荒”到“退耕还林”，这不仅是我国林业发展模式的重大跨越，也是我国坚定不移地实施可持续发展战略的历史见证，标志着我国走上了人与自然和谐发展之路。
解振华代表说，在过去相当长的时期里，可持续发展对于中国人来说，还是一个陌生的概念。
为了吃饭，人们围湖造田、盲目垦荒，破坏了生态平衡；为了工业化，人们把“机器轰鸣”、“烟囱林立”视为繁荣的象征，忽视了生态环境的承载力。
然而，这种粗放型的发展模式，并没有真正解决中国的发展问题。
到20世纪90年代初，我国环境污染趋势加剧，生态不断恶化，制约着经济发展，威胁着群众健康。
可持续发展战略是中国的必然选择。
1992年6月，联合国在巴西召开了“环境与发展”世界首脑会议，通过了《里约宣言》和《21世纪行动议程》。
包括中国在内的与会各国一致承诺：把走可持续发展之路作为未来的长期共同的发展道路。
可持续发展，就是既考虑当前发展的需要，又考虑未来发展的需要，不以牺牲后代人的利益为代价来满足当代人的利益。
这是全世界对人与自然关系重新审视后得出的深刻认识。
1994年3月，我国在世界上率先颁布了国家级《21世纪议程》—《中国21世纪议程》，并陆续出台了《关于环境保护若干问题的决定》、《全国生态环境建设规划》和《全国生态环境保护纲要》等一系列纲领性文件，把可持续发展战略贯穿到经济和社会发展的总体布局和长远规划。
选择什么样的道路，决定着中国未来的命运。
2001年，江泽民同志从中华民族的长远利益和生存发展大计出发，高屋建瓴地指出：人口、资源、环境工作，是“强国富民安天下的大事”。
从绿色奥运到南水北调，从西部大开发到绿色青藏铁路，人们可以看到一个全新的理念：可持续发展。
近年来，我国在发展经济的同时统筹考虑人口、资源、环境等问题，为控制人口增长、改善生态状况、遏制环境污染做出了不懈努力。
随着可持续发展理念的深入人心，“环保”已成为人们日常生活中使用频率最高的词汇之一，“绿色”正成为五彩缤纷的现代中国最时尚的色彩。
“可持续发展能力不断增强，生态环境得到改善，资源利用效率显著提高，促进人与自然的和谐，推动整个社会走上生产发展、生活富裕、生态良好的文明发展道路。
”这是十六大报告确定的在新世纪新阶段全面建设小康社会的目标之一。
—摘自《人民日报》2002年11月11日根据材料内容回答问题：（1）可持续发展的含义是什么？（2）我国走可持续发展道路的必要性及意义。
（3）结合身边事例说明实施可持续发展战略的措施。
[参考答案]一、单向选择题1、Ａ2、Ｂ3、Ｂ4、Ｂ5、Ａ6、Ｄ7、Ｃ8、Ｄ9、Ａ 10、Ｄ 11、Ａ 12、Ｃ 13、Ａ 14、Ｂ 15、Ｂ二、多向选择题1、ＡＣＤＥ2、ＡＢＣ3、ＡＢＣ4、ＡＢＣＤ5、ＢＣＤＥ6、ＡＢＣＤ7、ＡＢＣ8、ＡＢ9、ＡＢＣＤＥ 10、ＡＥ三、辨析题1、（1）、改革开放以来非公有制经济的迅速发展改变了我国所有制结构不合理的状况，解放和发展了生产力，是我国经济体制改革的重大经济成果之一（2分）；（2）、公有制经济是社会主义经济制度的基础，在所有制结构中仍然占据主体地位，在社会主义市场经济发展的过程中也在不断发展和壮大自己，增强自身的竞争力（2分）；（3）、国有经济是公有制经济的主要代表者，在社会主义市场经济中仍然控制着国民经济命脉，对经济发展起主导作用（2分）；（4）、公有制经济的比重有所减少并不代表公有制的主体地位发生变化，也不会影响我国社会主义的性质（1分）。
2、（1）、社会主义市场经济是法制化经济，这是社会主义市场经济的基本特征（2分）；（2）、在社会主义市场经济建设过程中，应该加强法制建设，以法律约束和规范人民的经济行为（2分）；（3）、道德规范是人民在生产生活过程中约定俗成的行为规范，对人民的行为也会起到一定的约束和规范作用（2分）；（4）、在参与市场经济过程中，人民的经济行为既要受法律的约束和规范，同时也要受到的规范的约束（2分）。
四、分析论述题1、（1）、邓小平理论是在和平与发展成为时代主题和新技术革命浪潮兴起的条件下形成和发展起来的（2分）；（2）、邓小平理论是在总结我国社会主义胜利和挫折历史经验并借鉴其他国家社会主义兴衰成败历史经验的基础上形成和发展起来的（2分）；（3）、邓小平理论是在我国改革开放和社会主义现代化建设的实践过程中形成和发展起来的（2分）；（4）、邓小平理论是在马列主义毛泽东思想的理论基础上形成和发展起来的（2分）；（5）、邓小平理论是马克思主义与当代中国实际相结合的第二次历史性飞跃的理论成果（2分）。