AG-240128A中文资料

合集下载

MGLS240128 LCD

在目前诸多的显示器件中，液晶显示器以其具有工作电压低、功耗低、显示信息量大、寿命长、不产生电磁辐射污染、可以显示复杂的文字及图形等优点，而在各种仪器仪表、电子设备、移动通讯及家用电器中得到了广泛的应用。

本文介绍ＭＧＬＳ２４０１２８Ｔ图形液晶显示模块就是香港精电公司生产的、内藏Ｔ６９６３Ｃ控制器的液晶显示模块。

２．１基本功能ＭＧＬＳ２４０１２８Ｔ图形液晶显示模块由控制器Ｔ６９６３Ｃ、列驱动器Ｔ６Ａ３９、行驱动器Ｔ６Ａ４０以及与外部设备的接口等几部分组成，它既能显示字符（包括中文和西文字符），又能显示图形，还能够将字符与图形混合显示。

其主要参数如下：●点阵数：２４０×１２８；●点尺寸：０．４×０．４ｍｍ；●视屏尺寸：１１４×６４ｍｍ；●汉字字体：８×８，８×６；●背光：ＬＥＤ或ＥＬ；●电源：＋５Ｖ；●工作温度范围：－２０～＋７０℃。

２．２引脚功能ＭＧＬＳ２４０１２８Ｔ图形液晶显示模块的引脚说明如表１所示。

该模块对液晶显示的控制和驱动都由模块内部的芯片及电路来完成，因此它与外部的连接只有数据线和控制线。

主控ＣＰＵ通过这些数据线和控制线来设置所需要的显示方式，其它功能均由模块自动完成。

表1 MGLS240128T模块的引脚功能２．３指令系统ＭＧＬＳ２４０１２８Ｔ图形液晶显示模块本身内藏控制器Ｔ６９６３Ｃ，它最大的特点是具有独特的硬件初始设置功能，由于显示驱动所需的参数（如占空比系数、驱动传输的字节数／行以及字符的字体选择等）均由引脚电平来设置，因此Ｔ６９６３Ｃ的初始化在上电时就已基本设置完成。

除此之外，它还具有很强的软件控制能力，也就是由主控ＣＰＵ通过接口写入液晶模块的指令来实现模块控制。

软件控制主要集中于显示功能的设置上。

该模块的常用指令如表２所列。

表2 MGLS240128T模块的常用指令设置３液晶模块的应用３．１与单片机的接口连接ＭＧＬＳ２４０１２８Ｔ液晶显示模块与计算机的接口时序采用Ｉｎｔｅｒ８０８０时序。

240128a

图形点阵液晶显示模块使用手册240128A一.概述240128A是一种图形点阵液晶显示器。

它主要采用动态驱动原理由行驱动器、控制器和列驱动器三部分组成了240(列)×128(行)的全点阵液晶显示。

此显示器采用了SMD的硬封装方式，通过导电橡胶和压框连接LCD,使其寿命长，连接可靠。

二.特性1.工作电压为+5V±10% ,可自带驱动LCD所需的负电压。

2.全屏幕点阵，点阵数为240(列)×128(行),可显示15(/行)×8(行)个(16×16点阵)汉字，也可完成图形，字符的显示。

3.与CPU接口采用4条位控制总线和8位并行数据总线输入输出，适配Inter8080系列时序。

4.内部有显示数据锁存器，和用于文本显示的6×8和8×8的字符库。

5.简单的操作指令。

三.外形尺寸.外形尺寸项目标准尺寸单位模块体积 144.0×104.0×12mm定位尺寸 138.0×97.0mm视域114.0×64.0 mm行列点阵数 240×128dots点距离 0.45×0.45mm点大小0.40×0.40mm四.硬件说明1.引脚特性引脚号引脚名称级别引脚功能描述1FG0V压框地2 VSS 0V电源地3 VDD +5V 电源电压4 VLCD 0～-10V LCD驱动负电压，要求VDD-VLCD=10V5 /WR H/L 低电平有效。

写操作信号6 /RD H/L 低电平有效。

读操作信号7 /CE H/L低电平有效。

片选信号C/D=H 为指令通道 8C/D H/L 通道选择信号C/D=L 为数据通道9 /RESET H/L 复位信号,低有效10 DB011 DB112 DB213 DB3H/L八位三态并行数据总线14 DB415 DB516 DB617 DB7FS=H, 6×8点阵字体18 FS H/L字体选择。

LCM240128液晶模块及其应用

LCM240128液晶模块及其应用发表时间：2009-11-12T14:19:53.950Z 来源：《赤子》第14期供稿作者：孙刚[导读] 随着液晶显示技术的发展，LCD（液晶显示器）模块已成为家电、显示仪器仪表和其他电子产品的重要组成部分孙刚（空军航空大学基础部电工电子教研室，吉林长春 130022）摘要：介绍了北京新华龙公司生产的LCM240128液晶显示模块，从应用角度介绍了其特点及功能，在此基础上设计了其与C8051F020单片机的接口，最后对汉字显示方法进行了介绍并举出实例。

关键词：LCM240128；T6963C；汉字显示引言随着液晶显示技术的发展，LCD（液晶显示器）模块已成为家电、显示仪器仪表和其他电子产品的重要组成部分。

LCD模块具有低工作电压、微功耗、信息量大、寿命长等诸多特点，在科研、生产与产品设计等领域正发挥着越来越重要的作用。

首先对北京新华龙公司生产的具有240×128分辨率的LCM240128大屏幕液晶显示模块进行介绍，然后设计了该模块与C8051F020单片机的接口电路，最后提出一种用该模块实现汉字显示的一种方案并给出实例。

1 LCM2401281液晶显示器简介LCM2401281是北京新华龙公司生产液晶显示模块，它具有240×128分辨率，即显示屏幕具有240×128点阵，整个液晶模块包括LCD 显示屏、LCD驱动电路、连接件、LCD控制模块、PCB线路板、背光源和结构件等。

其驱动电压可调8至26V，逻辑电压5V。

其控制模块采用的是东芝公司T6963C。

T6963C控制模块具有21个I/O接口引脚T6963C与单片机硬件接口的缓冲区由5个缓冲器组成，它们分别是用于接收单片机信息的指令锁存器和数据锁存器，用于向单片机发送信息的状态缓冲器和2个数据缓冲器。

其中状态缓冲器中给出的是T6963C当前工作状态的状态字，T6963C的状态字多达7位，分别是S7、S6、S5、S4、S3、S2、S1和S0。

GB240128BSGBAMLA-V00中文资料

JEWEL HILL ELECTRONIC CO.,LTDJEWEL HILL ELECTRONIC CO.,LTD.SPECIFICATIONS FORLCD MODULEModule No. GB240128BOffice Address: Rm. 518,5/F., 101 Shangbu Industrial District,HuaqiangNorthRoad, Shenzhen, ChinaTEL : (86)-755-83362489 83617492FAX: (86)-755-83286396 83365871E-mail: sales@jhlcd@Website: TABLE OF CONTENTSLCM NUMBER SYSTEM (2)1. GENERAL DESCRIPTION (3)2. FEATURES (3)3. MECHANICAL SPECIFICATION (3)4. MECHANICAL DIMENSION (4)5. MAXIMUM RATINGS (5)6. ELECTRICAL CHARACTERISTICS (5)7. MODULE FUNCTION DESCRIPTION (6)8. ELECTRO-OPTICAL CHARACTERISTICS (15)9. RELIABILITY (19)10. PRECAUTIONS FOR USING LCD MODULES (20)11. USING LCD MODULES (22)12. REVISION HISTORY (24)SAMPLE APPROVED REPORT (25)LCM Number SystemNUMBER OF CHAR. PER LINE F: FSTN; X: OTHER VERSION NUMBER: V00~V99IC TYPE:VIEWING DIRECTION:TEMPERATURE RANGE:BACKLIGHT TYPE:SERIAL NUMBER: A~ZGRAPHIC MODULEs: NUMBER OF COMMONs GRAPHIC MODULEs:NUMBER OF SEGMENTs COB & SMT LCMBACKLIGHT COLOR:CHARACTER MODULEs:CHARACTER MODULEs: NUMBER OF LINE G: REFLECTIVE,NONE BACKLIGHT A: TRANSFLECTIVE, EL BACKLIGHT B: TRANSMISSIVE, EL BACKLIGHT C: TRANSFLECTIVE, LED BACKLIGHT D: TRANSMISSIVE, LED BACKLIGHT E: TRANSFLECTIVE, CCFL BACKLIGHT F: TRANSMISSIVE, CCFL BACKLIGHT A: AMBER; B: BLUE; Y: YELLOW-GREEN R: RED; W: WHITE; O: THER COLOR N: NORMAL TEMPERATURE RANGE U: UPPER(12:00); D: DOWN(6:00)L: LEFT(9:00); R: RIGHT(3:00);A: BONDING IC, WITH CONTROLLER B: BONDING IC, WITHOUT CONTROLLER C: SMT IC, WITH CONTROLLER D: SMT IC, WITHOUT CONTROLLER O: OTHER TYPEW: BLACK-WHITE; O: OTHER G: GRAY; Y: YELLOW-GREEN; B: BLUE; LCD COLOR MODE:N: TN; H: HTN; S: STN LCD TYPE:S: SUPER WIDE TEMPERATURE RANGE W: WIDE TEMPERATURE RANGEM: MIDDLE TEMPERATURE RANGE1. GENERAL DESCRIPTIONThe GB240128B is a 240 x 128 Dots Graphics LCD module. It has a FSTN panel composed of240segments and 128 commons. The LCM can be easily accessed by micro-controller via parallel interface.2. FEATURESTransmissive and NegativeDisplay ModeFSTN moduleDisplay Format Graphic 240 x 128 dotsInput Data Parallel data input from MPUMultiplexing Ratio 1/128 DutyBiasBias 1/13Viewing Direction 6 O’clock(White)Backlight LED3. MECHANICAL SPECIFICATIONItem Specifications Unit Dimensional outline 144.0 x 104.0 x 13.5(max) mmResolution 240segs x 128coms dotsActive area 107.95(W) x 57.55(H) mmDots pitch 0.45 (W)×0.45(H) mmDots size 0.4(W)×0.4 (H) mm4. MECHANICAL DIMENSION5. MAXIMUM RATINGSItem Symbol Min Max Unit NoteV DD - V ss -0.3 5.5 V Supply voltage V LCD -0.3 24.0 V Input Voltage V IN -0.3 V DD +0.3 VOperating temperature T OPR -10 +60 Storage temperature T STR -20 +70Humidity --- --- 90 %RH6. ELECTRICAL CHARACTERISTICSItem SymbolCondition Min. Typ. Max. UnitSupply Voltage Logic V DD ------ 5.0 --- VH level V IH 0.8V DD --- V DDInput VoltageL levelV IL --- V SS --- 0.2V DDVCurrent Consumption(LCD DRIVER)I DD V DD =5.0V; V LCD =19.5V, T amb =25 ;--- --- 25.0 mALCD Driving Voltage V LCDBias=1/13V LCD =V DD -V 019.2 19.5 19.8 VCurrent Consumption (With LED BackLight)I LEDV DD =5.0V;V LED =3.4V,T amb =25 ;--- --- 300 mA7. MODULE FUNCTION DESCRIPTION 7.1. PIN DESCRIPTIONPin No. Symbol Description1 VSSPower supply for Ground (0V)2 VCCPower supply for positive (+5V)3 VOLCD driver voltage regulation pin4 C/DH:Intraction; L:Data5 /RDRead Enable signed, “L”: Read6 /WRWrite selection signal, ”L”: Write7 DB08 DB19 DB210 DB38-bit bi-directional data bus11 DB412 DB513 DB614 DB715 /CEChip Enable Signal16 /RSTReset signal17 VOUTPower supply voltage for LCD driving18 MDColumns select; “H”: 32; “L”: 4019 FSFont Selection; “H”: 6*8; “L”: 8*820 NC/LEDA No Connect or Supply voltage for LED Positive21 NC/LEDK No Connect or Supply voltage for LED negative7.2 TIMING CHARACTERISTICS7.3 APPLICATION OF LCMCircuit Block Diagram/WR/RD/CEC/DFSRSTFGVDDVSSVEELED+LED-7.4 TABLE OF COMMAND7.5 RAM INTERFACE7.6 FLOWCHART OF COMMUNICATION WITH MPU8. ELECTRO-OPTICAL CHARACTERISTICSItem Symbol Condition Temp Min Typ. Max UnitsNote--- 19.8 ---25 18.8 19.5 20.2 LCD driving voltageV LCD = = 050 --- 19.2 --- V NOTE1Rise Time (Tr) --- --- -- Decay Time (Tf)0 --- ---- --- Rise Time (Tr) --- 225 340Decay Time (Tf) 25 --- 240 360Rise Time (Tr) --- --- -- Response TimeDecay Time (Tf)= = 0 50 --- --- --msec NOTE2Contrast Ratio Cr= = 0 255 10 --- --- NOTE4Viewing AngleRange( = 0°)(6”) = 90°(3”) =180°(12”) =270°(9”)(25 ) CR ≥250 35 25 40DegNOTE3z For panel only․Electro-Optical Characteristics Measuring Equipment(DMS501)SystemIllumination (D65)․Note 1. Definition of Driving Voltage( Vlcd) :․Note 3. Definition of Viewing Angle and :․Note 4. Definition of Contrast ratio( CR) :Brightness of Non-selected Segment (B2)Brightness of Selected Segment (B1)CR =V,maxCR,maxDriving VoltageB r i gh t n e s s (%)Brightness Curve forSelected Segment0%=90 =270Viewing Direction 6 O’clock DirectionNormal :9. RELIABILITY9.1. MTBFThe LCD module shall be designed to meet a minimum MTBF value of 50000 hours with normal. (25°C in the room without sunlight)9.2. TESTSNO. ITEM CONDITION CRITERION 1 High Temperature Operating 60 120Hrs2 Low Temperature Operating -10 120Hrs3 High Temperature/Humidity Non-Operating60 ,90%RH ,120 Hrs4 High TemperatureNon-Operating70 120Hrs5 Low TemperatureNon-Operating-20 120Hrs6 Temperature CyclingNon-Operating -10 (30Min )↔ 60 (30Min)10 CYCLESNo Defect OfOperational Function InRoom Temperature AreAllowable.IDD of LCM inPre-and post-test shouldfollow specificationNotes: Judgments should be mode after exposure in room temperature for two hours.10. PRECAUTIONS FOR USING LCD MODULES10.1. HANDLING PRECAUTIONS(1) The display panel is made of glass. Do not subject it to a mechanical shock or impact by droppingit.(2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any inyour mouth. If the substance contacts your skin or clothes, wash it off using soap and water.(3) Do not apply excessive force to the display surface or the adjoining areas since this may cause thecolor tone to vary.(4) The polarizer covering the display surface of the LCD module is soft and easily scratched. Handlethis polarizer carefully.(5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a softdry cloth. If it is heavily contaminated, moisten a cloth with one of the following solvents: - Isopropyl alcohol- Ethyl alcohol(6) Solvents other than those above mentioned may damage the polarizer.Especially, do not use the following:- Water- Ketone- Aromatic solvents(7) Extra care to minimize corrosion of the electrode. Water droplets, moisture condensation or acurrent flow in a high-humidity environment accelerates corrosion of the electrode.(8) Install the LCD Module by using the mounting holes. When mounting the LCD Module, makesure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/Ocable or the backlight cable.(9) Do not attempt to disassemble or process the LCD Module.(10) NC terminal should be open. Do not connect anything.(11) If the logic circuit power is off, do not apply the input signals.(12) To prevent destruction of the elements by static electricity, be careful to maintain an optimumwork environment.- Be sure to ground the body when handling he LCD Module.- Tools required for assembling, such as soldering irons, must be properly grounded.-To reduce the amount of static electricity generated, do not conduct assembling and other workunder dry conditions.-The LCD Module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated.10.2. STORAGE CONDITIONSWhen storing, avoid the LCD module to be exposed to direct sunlight of fluorescent lamps. For stability, to keep it away form high temperature and high humidity environment (The best condition is : 23±5°C, 45±20%RH). ESD protection is necessary for long-term storage also.10.3. OTHERSLiquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low temperature.If the LCD Module have been operating for a long time showing the same display patterns the display patterns may remain on the screen as ghost images and a slight contrast irregularity may also appear.A normal operating status can be recovered by suspending use for some time. It should be noted that this phenomenon does not adversely affect performance reliability.To minimize the performance degradation of the LCD Module resulting from destruction caused by static electricity etc. exercise care to avoid holding the following sections when handling the modules.- Exposed area of the printed circuit board.- Terminal electrode sections.11. Using LCD modules11.1 LIQUID CRYSTAL DISPLAY MODULESLCD is composed of glass and polarizer. Pay attention to the following items when handling.(1) Please keep the temperature within specified range for use and storage. Polarization degradation,bubble generation or polarizer peel-off may occur with high temperature and high humidity.(2) Do not touch, push or rub the exposed polarizers with anything harder than a HB pencil lead (glass,tweezers, etc).(3) N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers andreflectors made of organic substances, which will be damaged by chemicals such as acetone, toluene, toluene, ethanol and isopropyl alcohol.(4) When the display surface becomes dusty, wipe gently with absorbent cotton or other soft materiallike chamois soaked in petroleum ether. Do not scrub hard to avoid damaging the display surface.(5) Wipe off saliva or water drops immediately, contact with water over a long period of time maycause deformation or color fading.(6) Avoid contacting oil and fats.(7) Condensation on the surface and contact with terminals due to cold will damage, stain orpolarizers. After products are tested at low temperature they must be warmed up in a container before coming is contacting with room temperature air.(8) Do not put or attach anything on the display area to avoid leaving marks on.(9) Do not touch the display with bare hands. This will stain the display area and degrade insulationbetween terminals (some cosmetics are determinate to the polarizers).(10)As glass is fragile, it tends to become or chipped during handling especially on the edges. Pleaseavoid dropping or jarring.11.2 INSTALLING LCD MODULEAttend to the following items when installing the LCM.(1) Cover the surface with a transparent protective plate to protect the polarizer and LC cell.(2) When assembling the LCM into other equipment, the spacer to the bit between the LCM and thefitting plate should have enough height to avoid causing stress to the module surface, refer to the individual specifications for measurements. The measurement tolerance should be ±0.1mm.11.3 ELECTRO-STATIC DISCHARGE CONTROLSince this module uses a CMOS LSI, the same careful attention should be paid for electrostatic discharge as for an ordinary CMOS IC.(1) Make certain that you are grounded when handing LCM.(2) Before removing LCM from its packing case or incorporating it into a set, be sure the module andyour body have the same electric potential.(3) When soldering the terminal of LCM, make certain the AC power source for the soldering irondoes not leak.(4) When using an electric screwdriver to attach LCM, the screwdriver should be of groundpotentiality to minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor.(5) As far as possible, make the electric potential of your work clothes and that of the workbenches tothe ground potential.(6) To reduce the generation of electro-static discharge, be careful that the air in the work is not toodried. A relative humidity of 50%-60% is recommended.11.4 PRECAUTIONS FOR OPERATION(1) Viewing angle varies with the change of liquid crystal driving voltage (Vo). Adjust Vo to showthe best contrast.(2) Driving the LCD in the voltage above the limit will shorten its lifetime.(3) Response time is greatly delayed at temperature below the operating temperature range. However,this does not mean the LCD will be out of the order. It will recover when it returns to the specified temperature range.(4) If the display area is pushed hard during operation, the display will become abnormal. However, itwill return to normal if it is turned off and then on.(5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit.Therefore, this product must be used and stored within the specified condition of 23±5°C, 45±20%RH.(6) When turning the power on, input each signal after the positive/negative voltage becomes stable.11.5 SAFETY(1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off withsolvents such as acetone and ethanol, which should later be burned.(2) If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash offthoroughly with soap and water.12. REVISION HISTORYrecord Date Version Reviseversion 05-11-011.0 Original2.0 Change specification format 05-11-203.0 Change contact mode 06-08-04SAMPLE APPROVED REPORT。

HS240128系列

1. 引脚功能（T6963C 适配 Intel8080 时序）
D7-D0 /RD /WR /CE C/D
三态输人输人输人输人
数据总线低电平有效，MCU 对 T6963C 的读操作信号低电平有效，MCU 对 T6963C 的写操作信号低电平有效，MCU 对 T6963C 的片选信号通道选择信号，C/D=1 指令通道，C/D=0 数据通道
z Intel8080 系列微处理器接口 z 6×8 和 8×8 字体可选 z 图形方式、文本方式以及图形与文本混合显示，文本方式下的特征显示图形拷贝功能 z 内置字符发生器 CGROM，含 128 个字符。模块上带 32K 显示缓冲区。
HS240128A 采用 COB 工艺制作结构稳固，使用寿命长。
5 --------------------------------------------------------------------------------------------------------------------------------------------------------------------------
107.95(A.A)
MAX13.5 9.0± 0.3
? 3.0 ? 6.0
0.40
104.0± 0.3 97.0
79.8± 0.2 64.0(V.A) 57.55(A.A)
K
240x128 DOTS
A
0.05
0.40 0.05
34
23 22
1
12-? 1.0
22-? 1.0
1.6
2.5
31.6
Hale Waihona Puke 2.54x11=27.94

240128oled显示屏技术说明书【智能屏编程指南】

JR240128-1A OLED 智能显示终端使用说明书JR240128-1A OLED 智能显示终端使用说明书修订历史版本号说明备注V1.0 2019年8月第一版目录1. 产品简介………………………………………………………………… （3）2. 结构尺寸图……………………………………………………………… （4）3. 电气参数………………………………………………………………… （5）4. 接口说明…………………………………………………………… （6～7） 4.1 用户接口…………………………………………………………… （6） 4.2 通讯端口…………………………………………………………… （7）5. 指令集……………………………………………………………… （8～19） 5.1 指令结构………………………………………………………………(8) 5.2 指令集说明 …………………………………………………………（9） 5.3 系统类指令集表………………………………………………（10～12） 5.4 图形绘制类指令集表…………………………………………（13～15） 5.5 文字显示类指令集表………………………………………… 5.6 图像显示类指令集表…………………………………………6. 使用注意事项………………………………………………………（20～22）（１６～１７）（１８～１９）JR240128-1A OLED 智能显示终端使用说明书1.智能型 16 灰阶OLED 终端简介JR240128-1A是深圳市吉润实业有限公司在广泛汲取了众多客户要求和建议的基础上，采用32 位RSIC-MCU 开发的一款易使用的3.37寸OLED屏智能终端，可以直接和具有UART/RS232/SPI 等串行接口的MCU（如51 单片机、AVR、PIC、DSP、ARM、工控机等）连接。

用户只需通过串口向终端发简单的命令，就可以实现绘图和显示功能，用户代码中无需进行繁琐的计算和操作。

RT240128A说明书

指令表：
表2
COMMAND
Register Set
Control Word set
Mode set
Display Mode
Cursor Pattern Select
Data auto Read/write
Data read Write
Screen peek Screen copy
CODE
00100001 00100010 00100100 01000000 01000001 01000010 01000011 1000x000 1000x001 1000x011 1000x100 10000xxx 10001xxx 10010000 1001xx10 1001xx11 100101xx 100110xx 100111xx 10100000 10100001 10100010 10100011 10100100 10100101 10100110 10100111 10110000 10110001 10110010 11000000 11000001 11000010 11000011 11000100 11000101 11100000 11101000 11110XX
2.5
2.54x19=48.26
4.92
4- R1.5
2. 外形尺寸一览
表1 ITEM
模块体积视域行列点阵数点距离点大小
图1
NOMINAL DIMEN
144.0×104.0×13.7 114.0×64.0 240×128 0.40×0.40 0.45×0.45
DETAIL A:
1.6
UNIT mm mm DOTS mm mm
VDD V
Input low voltage

EDM240128B图形点阵式液晶显示模块使用说明

LCD 模块使用手册EDM240128B图形点阵式液晶显示模块使用说明大连佳显电子有限公司电话: (0411) 84619565, 84573876传真: (0411) 846195851. 使用范围----------------------------------------------------32. 质量保证----------------------------------------------------33. 性能特点----------------------------------------------------34. 外形图-------------------------------------------------------65. I/O接口特性-----------------------------------------------76. 质量等级---------------------------------------------------167. 可靠性---------------------------------------------------198. 生产注意事项---------------------------------------------209. 使用注意事项---------------------------------------------211. 使用范围该检验标准适用于大连佳显电子有限公司设计提供的标准液晶显示模块。

如果在使用中出现了异常问题或没有列明的项目，建议同最近的供应商或本公司联系。

2. 质量保证如在此手册列明的正常条件下使用、储存该产品，公司将提供12个月的质量保证。

3. 性能特点3-1．性能：显示方式 : 半透、正显FSTN/STNLCD显示颜色 : 显示点: 黑色背景: 白色显示形式: 240(w)×128(h) 全点阵输入数据 : 来自MPU的8位并行数据接口Duty驱动路数: 1/128视角: 6 点RAM 显示容量: 32k byte S-RAM(built-in)HD61830(Built-in)控制器:容量: Built-in 160 words 5×7 and 32 words 5×CGROM/RAM11character generator (CG) ROM.3-2．机械性能：项目规格单位外形尺寸 144.0(W)×104.0(H) ×14.5 Max.(T) mm显示点阵数 240(W) ×128(H) Dots —字符结构5×7 Fonts and5×11 Fonts —视域 114.0(W)×64.0(H) mm显示图形域 107.95(W)×57.55(H) mm 点间距 0.45(W)×0.45(H) mm点尺寸 0.4(W)×0.4(H) mm145 g 重量 Approx.3-3．极限参数：项目符号最小值最大值单位注释逻辑 Vdd 0 6.0 V电源电压LCD 驱动 Vdd – Vee 0 26 V输入电压 Vi 0 Vdd V 操作温度 Top -20 70 ℃ 储存温度 Tstg -30 85 ℃ 湿度 — — 90 %RH3-4．电气特性：3-4-1. 电气参数项目符号条件最小值典型值最大值单位逻辑 Vdd 4.5 5.0 5.5电源电压LCD 驱动 Vdd–Vee — 21.0 24.0高电平 Vih Vdd=5V ±5% 0.7Vdd — Vdd输入电压低电平 Vil 0 — 0.3Vdd V高电平 Vih Vdd-0.4— Vdd输出电压低电平 Vil 0 — 0.4频率 Fflm Vdd=5V 60 70 80 Hz逻辑 Idd — 3.0 5.0功耗 LCD 驱动 Iee Vdd=5V Vdd–Vee=15.0VFflm=75Hz— 2.0 3.5 mA Ta= 0℃φ=0°,θ=0°— 22.1 23.0Ta= 25℃φ=0°,θ=0°20.0 21.0 21.7 LCD 驱动电压 (推荐电压) Vdd–Vee Ta= 50℃φ=0°,θ=0° 19.2 20.3 —VNote: <1> 驱动路数=1/128 <2> 所有点在静态条件下3-5．电光特性项目符号温度条件最小值典型值最大值单位注释 0℃ — 22.1 23.025℃20.0 21.0 21.7 LCD 驱动电压(推荐电压)V op 50℃ φ=0°,θ=0°19.2 20.3 — V 1,2,5 0℃ — 1500 2000 上升时间 tr 25℃ — 150 2000℃ — 30003500响应时间衰退时间 td 25℃ φ=0°,θ=0°— 200 250mS 1,3,5垂直 -35 — 35视角 Δφ 25℃ 水平 -30 — 30deg. 1,4,5对比度 K 25℃ φ=0°,θ=0° 2.0 5.0 — — 1,5,6注意：<1> φ和θ的定义<2> 在此电压范围内能获得对比度大于2(k ≥2)注意：<4>视角定义注意：<5> 光学测量系统温度控制室(ΔΦ) ΔΦ=|Φ1-Φ2|非选择点的亮度(B2)选择点的亮度(B1)4. 外形图5. I/O接口特性5-2．时序及时序图：1. 接口时序2.接口时序参数名称符号最小值典型值最大值单位E周期时间t CYC 1.0 — —us E高电压宽度t WEH 0.45 — —E低电压宽度t WEL 0.45 — —E上升时间t Er — — 25E下降时间t Ef — — 25 地址建立时间t AS 140 — —数据建立时间t DSW 225 — —ns 数据延迟时间t DDR — — 225 数据保持时间t DHW 10 — — 地址保持时间t AH 10 — — 输出数据保持时间t DH 20 — —5-3. 电源连接图*VDD-V0:液晶驱动电压。

金鹏电子 OCM240128 图形点阵液晶显示模块说明书

OCM240128图形点阵液晶显示模块使用说明书-------------------------------------------------------------------------------------------------感谢您关注和使用我们的字符点阵系列液晶显示器产品，欢迎您提出您的要求、意见和建议，我们将竭诚为您服务、让您满意。

您可以浏览了解最新的产品与应用信息，或拨打热线电话0758－2317153以及向*************邮箱发E-mail获取具体的技术咨询与服务。

金鹏电子有限公司Golden Palm Electronics Co.,Ltd.目录(一) 显示特性 (3)(二) 模块尺寸 (3)(三) 模块图 (4)(四) 限定参数 (4)(五) 电气特性及使用说明 (4)(六) 光学特性 (7)(七) 可靠性 (9)(八) 注意事项 (10)1Display Specification1.1 Display type：STN1.2 Display colorDisplay color：Blue-BlackBackground color：Yellow-Green1.3 Polarizer mode：PositiveReflective1.4 Viewing Angle：6:001.5 Driving Duty： 1/1281.6 Backlight： LED Or CCFLz Color tone is slightly changed by temperature and driving voltage。

2Mechanical Specifications图1：OCM240128-1/-2模块尺寸图7 /CE Chip enable SignalSelection8 C/D Command/Datasignal9 /Reset Reset10 DB0 Data bit 011 DB1 Data bit 112 DB2 Data bit 213 DB3 Data bit 314 DB4 Data bit 415 DB5 Data bit 516 DB6 Data bit 617 DB7 Data bit 7Selection18 FS Font19 VEE Negative voltage for LCD driving20 LED+ Power supply for LED(+5V)21 LED- Power supply for LED(0V)OCM240128_2：Pin NO.Symbol Description(Function) Remark 1 FG Module Frame GroundGround2 VSS3 VDD Supply voltage for logic and LCD(+5V)4 V0 Operating voltage for LCD variable5 /WR Data Write into T6963C6 /RD Data Read from T6963C7 /CE Chip enable Signal8 C/D Command/DataSelectionsignal9 /Reset Reset10 DB0 Data bit 011 DB1 Data bit 112 DB2 Data bit 213 DB3 Data bit 314 DB4 Data bit 415 DB5 Data bit 516 DB6 Data bit 617 DB7 Data bit 7Selection18 FS Font19 LED+ Power supply for LED(+5V)20 LED- Power supply for LED(0V)5.3 Interface Timing Chart:Unless otherwis e specified,VDD=5.0±10％,VSS=0V,Ta=-10~70℃MINUNITMAX Item SymbolTestConditionC/D Set up Time tCDS 100 -- nsC/D Hold Time tCDH 10 -- nsCE,RD,WR Width tCE,tRD,tWR80 -- nsData Set up Time tDS 80 -- nsData Hold Time tDH 40 -- ns Access Time tACC -- 150 ns Output Hold Time tOH 10 50 ns5.4 Instruction CodeCOMMAND CODE D1 D2 FUNCTION REGISTERS 00100001 X address Y address Set Cursor Pointer00100010 Data 00H Set Offset Register SETTING 00100100 Low address High address Set Address Pointer01000000 Low address High address Set Text Home AddressAreaSET CONONTROL 01000001 Columns 00H SetTextWORD 01000010 Low address High address Set Graphic Home Address01000011 Columns 00H SetAreaGraphicmode1000x000 -- -- OR1000x001 -- -- EXORmodemode MODE SET 1000x011 -- -- AND1000x100 -- -- TextmodeAttributemodeROMCG10000xxx -- -- InternalmodeRAM10001xxx -- -- ExternalCGoff10010000 -- -- Display1001xx10 -- -- Cursor on, blink off1001xx11 -- -- Cursor on, blink onDISPLAY MODE 100101xx -- -- Text on, graphic off100110xx -- -- Text off, graphic on100111xx -- -- Text on , graphic oncursor10100000 -- -- 1-linecursor10100001 -- -- 2-linecursor10100010 -- -- 3-linecursor CURSOR 10100011 -- -- 4-linecursor PATTERN ELECT 10100100 -- -- 5-linecursor10100101 -- -- 6-linecursor10100110 -- -- 7-line10100111 -- -- 8-line cursor DATA AUTO10110000 -- -- Set Data Auto Write10110001 -- -- Set Data Auto Read READ/WRITE10110010 -- -- Auto Reset11000000 -- -- Data Write and Increment11000001 -- -- Data Read and Increment DATA11000010 -- -- Data Write and Decrement READ/WRITE11000011 -- -- Data Read and Decrement11000100 -- -- Data Write and Non variable11000101 -- -- Data Read and Non variable SCREEN PEEK11100000 -- -- Screen Peek SCREEN COPY11101000 -- -- Screen Copy11110xxx -- -- Bit reset11111xxx -- -- Bit set1111x000 -- -- Bit0 (LSB)1111x001 -- -- Bit1 BIT SET/RESET1111x010 -- -- Bit21111x011 -- -- Bit31111x100 -- -- Bit41111x101 -- -- Bit51111x110 -- -- Bit6 1111x111 -- -- Bit7 (MSB)5.5 Character Code Map6 Optical Characteristics6.1 Optical Characteristics Ta=25℃Item Symb olCondition Min. Typ.Max. Unit Remarkθx θy=0 -20 ---- 20 Viewing angle θy Cr>3 θx=0 -25 ---- -25 degContrast Ratio Cr θx=0° θy=15°3Turn on Ton θx=0° 200 Response Time Turn off Toff θy=0° 360 ms6.2 Definition of optical characteristics6.2.1Definition of viewing Angle(see fig.as follow)6.2.2Definition of Contrast Ratio(see fig.as follow) 1) ℃；2) Frame freguency : 32Hz6.2.3Definition of Response time (see fig.as follow)Contrast Ratio(K)=B2/B1———————————————— selected state brightness Measuring Conditions: Ambient Temperature: 257 Reliability7.1 Content of Reliablity TestNO. Test Item Content of Test Test condition High Temperature Endurance test applying the high 60℃1Storage storage temperature for a long time96H Low Temperature Endurance test applying the low 50℃Storage storage temperature for a long time 96HHigh TemperatureEndurance test applying the Temperature electric stress (voltage50℃3Operation&current) and the thermalstress to the element for a long time96HHigh TemperatureEndurance test applying the Temperature electric stress (voltage0℃4Operation&current) and the thermalstress to the element for a long time96HHigh Temperature Endurance test applying thehigh temperature and high humidity 5/Humidity Storage storage for a long time40℃ 90%RH 96H6 TemperatureCycleEndurance test applying the low andhigh temperature cycle 10 cycle-20℃--25℃--60℃--25℃30min 5min 30min 5min1cycle-20℃/60℃7 Vibration Test(package state)Endurance test applying thevibration during transportation10Hz~55Hz~10Hz1.5mmP-P,1.5gX.Y.-5mm8Shock Test(package state)Endurance test applying theshock during transportationDrop a product forma height of 79cm to asolid unbending andhorizontal plane9 AtmosphericPressure TestEndurance test applying theatmospheric prssure duringtransportation by air40kPa24H7.2 Failure Judgment CriterionCriterion Test Item NO. Failure JudgementItem Criterion Basic Out of the basicSpecification Specification Electrical Out of theSpecification electricalspecification Mechanical Out of theSpecification mechanicalspecification Optical Out of theCharacteristic opticalspecificationRemark Basic specification = Display specification + Mechanicalspecification8. Precautions for use of LCD ModulesOCM240128图形点阵液晶显示模块使用说明书8.1 Handling Precautions8.1.1The display panel is made of glass. Do not subject it to amechanical shock by dropping it from a high place, etc.8.1.2If the display panel is damaged and the liquid crystalsubstance inside it leaks out, be sure not to get any in yourmouth, if the substance comes into contact with your skinor clothes, promptly wash it off using soap and water.8.1.3Do not apply excessive force to the display surface or theadjoining areas since this may cause the color tone to vary.8.1.4The polarizer covering the display surface of the LCDmodule is soft and easily scratched. Handle this polarizercarefully.8.1.5If the display surface become contaminated, breathe on thesurface and gently wipe it with a soft dry cloth. if still notcompletely clear, moisten cloth with one of the followingsolvents:-----Isopropyl alcohol-----Ethyl alcoholSolvents other than those mentioned above may damagethe Polarizer. Especially, see the following:-----Water-----Ketone-----Aromatic solvents8.1.6Do not attempt to disassemble the LCD Module8.1.7 NC terminal should be open. do not connect anything8.1.8 If the logic circuit power is off, do not apply the inputsignals8.1.9To prevent destruction of the elements by electricity, becareful to maintain an optimum work environmenta.Be sure to ground the body when handling the LCD Modulesb.Tools required for assembly, such as solderingc.irons, must be properly ground.d.To reduce the amount of static electricity generateddo not conduct assembly and other work under dryconditions.e.The LCD Module is coated with a film to protect the displaysurface. Be care when peeling off this protective film since staticelectricity may be generated.肇庆金鹏电子有限公司Golden Palm Electronics Co.,Ltd. 共11页第11页地址：肇庆市建设四路13号天宁广场E幢13、14、15楼邮编：526040 E-mail: *************业务联系：0758－2317153/2317143 技术支持：0758－********************传真：0758－2317023。

OCM240128-1B说明书(文本混合显示累加和检验)

12.从机发现 MCLK=0,知道主机已经发出第二个数据. 13.从机收第二个 bit 的数据. 14.从机将 SCLK=0,表示已经收了第二个 bit.之后等待 MCLK 是否变 1,如果变 1,则主机已经发出了第三个 bit.
15.再重复 3-14,3 遍,传完 8bit 数据.
16.主机发现 SCLK=0,知道从机已经收完 8 位数据. 17.主机将 MCLK=1,准备下一轮通讯.
OCMO240128-1B说明书（文本混合显示累加和检验）
一、测试板连线方法
测试板有两组接口，分别是 JI 接口和 J2 接口。 1、 J1 接口有 5 个引脚，分别是 VCC，GND，MCLK，SCLK，SDA。其中 VCC 是电源正，接+5V。其中 GND 是电源地，接 0V。其中 MCLK 是主时钟线，用于主机（发送数据方即用户 MCU）申请数据通讯及报告数据状态。其中 SCLK 是从时钟线，用于从机（接受数据方即测试板）反馈从机数据处理状态。其中 SDA 是数据线，用于主机传输数据给从机。 2、J2 接口有 21 个引脚，分别接模块 OCM240128-1 的 1~21 脚，上电后要调整测试板上的电位器使模块达到最佳显示效果。注：模块 OCM240128-1 可视面积：114x64，点阵区面积 107.95x57.55，点阵数：240x128。
6.从机发现 MCLK=1,知道主机已经发出第一个数据. 7.从机收第一个 bit 的数据. 8.从机将 SCLK=1,表示已经收了第一个 bit.之后等待 MCLK 是否变 0,如果变 0,则主机已经发出了第二个 bit.
9.主机发现 SCLK=1,知道从机已经开始准备接受第二个数据. 10.主机发送第二个 bit 到 SDA. 11.主机将 MCLK=0,表示已经发送第二个 bit 到 SDA.

汉晶科技HG240128-01D系列说明书

HG240128-01D系列说明书（Version1.0）可选型号：产品型号及其后缀LCD类型（显示模式）背光类型（LED）时序方式逻辑电压（VDD）背光电压接口方式及其预留配置HG240128SYD-01DSYE STN黄绿底色黄绿背光80 5.0V 5.0V单排和双排插针焊位HG240128FPD-01DSWE FSTN 黑白正像白背光80 5.0V 5.0V单排和双排插针焊位HG240128SBD-01DSWE STN 蓝底色白背光80 5.0V 5.0V单排和双排插针焊位注：以上列出LCD类型为我公司标准产品，如果有其他需求，请致电我公司销售部！目录1、液晶显示模块整体描述-----------------------------------------------------------------------------------------32. 最大典型值---------------------------------------------------------------------------------------------------------43. 电气特性------------------------------------------------------------------------------------------------------------44. 光学特性-----------------------------------------------------------------------------------错误！未定义书签。

5. 光学特性测定方法------------------------------------------------------------------------------------------------56. 原理框图------------------------------------------------------------------------------------------------------------67. 时序图---------------------------------------------------------------------------------------------------------------68. 功能说明及指令集------------------------------------------------------------------------------------------------79. 字符代码表--------------------------------------------------------------------------------------------------------1610. LCD驱动电源连接方式---------------------------------------------------------------------------------------1611. 出厂测试报告----------------------------------------------------------------------------------------------------1712. 接口引脚定义----------------------------------------------------------------------------------------------------1813. 外形尺寸图纸----------------------------------------------------------------------------------------------------1814.液晶显示模块在使用过程中的注意事项--------------------------------------------------------------------211、液晶显示模块整体描述项目说明单位液晶显示模块组成液晶显示屏,背光灯箱,线路板,铁框,导电橡胶等液晶显示屏类型正像反射型,半透型,负像型液晶屏显示类型STN型:黄绿模式,灰模式,蓝模式FSTN型:黑白模式液晶显示屏视角 6 O’clock or 12 O’clock液晶模块外形尺寸 (LED*) 144.00(长)×104.00(宽)×13.00(厚) mm液晶模块视域 114.00(长)×64.00(宽) mm 液晶模块铁框尺寸 (LED*) 133.20(长)×80.00(宽)×13.00(厚) mm点阵液晶显示模块点阵数 240×128mm 液晶显示屏点尺寸 0.40(长)×0.40(宽)mm 液晶显示屏点间距 0.45(长)×0.45(宽) 液晶显示屏占空比 1/128液晶显示屏偏置电压 1/12液晶显示模块控制器 T6963C液晶显示模块使用温度范围(E*) -20~+70 ℃液晶显示模块存储温度范围(E*) -30~+80 ℃背光灯箱 LED:黄绿底色液晶显示模块数据输入格式八位并行输入格式,80时序方式电源输入电压 5V输入供电,内置DC/DC电路V液晶显示模块理论寿命 50,000 小时注意: LED*: LED背光E*: 宽温等级2. 最大典型值2.1 电气最大典型值Vss=0VUnitNote Item SymbolMin Max逻辑电源 Vdd-Vss 0 7.0 VLCD驱动电压 Vdd-V o 0 28.0 VVI/O口输入电压 Vi 0Vdd2.2 使用环境最大典型值Item Symbol Min Max Unit工作温度T0 -20 +70 ℃储存温度Ts -30 +80 ℃湿度 --- --- 85 %RH3. 电气特性3.1 电气特性Vss=0VItem Symbol Condition Min Typ Max Unit逻辑电压 Vdd ---- 4.5 5.0 5. 5 V LCD 驱动电压 Vdd-Vo ---- 15.5 --- 19.8 V输入电压最大值 VIH ---- Vdd-2.2--- Vdd V输入电压最小值 VIL ---- 0 --- 0.8 V 频率FELM Vdd=5V 65 78 85 Hz3.2 LED背光特性说明书背光颜色供电电流（典型值）黄绿背光 260mA白背光 140mA5. 光学特性测定方法6. 原理框图7. 时序图7.1 AC CHARACTERISTICSCharacteristic Symbol Min MaxUnitC/D set up time t CDS 100 --- ns C/D hold timet CDH 10 --- ns CE, RD, WR pulse width t CE , t RD , t WR80 --- ns Data set up time t DS 80 --- ns Data hold time t DH 40 --- ns Access time t ACC --- 150 ns Output hold timet OH10 50 ns7.2 TIMING CHARACTERISTICS8. 功能说明及指令集8.1. 读状态写入任何读写命令之前，必须检查“状态”寄存器。

PG240128A-L中文资料

Electrical Characteristics at TA = 25 °C, Vdd=5V+0.25V
Item Power Supply (Logic) Supply Current LCD Driving Voltage Input Voltage “H” Input Voltage “L” Output Voltage “H” Output Voltage “L” Symbol Vdd-Vss Idd Vdd -Vo Vih Vil Voh Vol Min 4.5 — 16.9 2.2 — 2.4 — Typ 5.0 15.0 18.0 — — — — Max 5.5 24.0 19.2 Vdd 0.6 — 0.4 Unit V mA V V V V V
Item Specifications Overall Size 144.0W x 104.0 x 10.3T (15.1T) Viewing Area 114.0W x 64.0H Active Area 117.95W x 57.55H Dot Size 0.40W x 0.40H Dot Pitch 0.45W x 0.45H
LED Backlight Specifications
Forward Voltage 4.35V2250mA (Max) Power Dissipation 10300mW (Max) Peak Wavelength 570nm (Typ)
Mechanical Specifications
PG240128B-L (240x128) Graphic LCD Display
170.0± 0.5 4.0 162.0
5.0
7.8 1.6
47.0 2.54 3.33 85.0±0.3

RTE24012中文资料

RTD14005 RTD14012 RTD14024
RTD34012 RTD34024 RT424012
RT424024 RT444012 RT444024
RTE24005 RTE24012 RTE24024
RTE44012 RTE44024
Outline Dimensions
.62 (15.7)
1.14 (29)
.051 DIA. (1.30)
.276
.400
(7.0)
(10.16)
.800 (20.32)
.800 (20.32)
.051 DIA. (1.30)
.300 (7.62)
.051 DIA. (1.30)
Contact Data
Arrangements: 1 Form A (SPST-NO) Wiring Diagram Code 1, 3. 2 Form A (DPST-NO) Wiring Diagram Code 5. 1 Form C (SPDT) Wiring Diagram Code 1, 3. 2 Form C (DPDT) Wiring Diagram Code 5.
Material: Silver-nickel 90/10. Minimum Load: 12V/100mA. Expected Mechanical Life: 10 million operations. Initial Contact Resistance: 100 milliohms max @ 1A 12VDC.
018 = 18VDC 048 = 48VDC 024 = 24VDC
4
012
Stock Items
RT114012 RT114024 RT134012

金属材料牌号

信泓日佳销售产品目录表信泓日佳模具钢材公司销售模具钢，进口模具钢，高速钢，粉末高速钢，钨钢，铝材，铜材，铝板，铝棒如：日本：PX4 PX5 PDS-3 PDS-5 PAK90 PD555 PD613 SGT S50C SC5C SUS303 SUS304 SUS410 SUS420 SUS630 SCM440 SMC420 SUP9 SK3 SK4 SKD4 SKD5 SKD7 SKD8 SKD11 SKD12 SKD61 SKD62 SKH-9 SKH-51SKH-55 SKH57 SKH59 SKT4 SKS3 SKS41 SLD SLD8 SLD10 SM400A SNC815 SPHD SS41 SS330 SS400 SS490 S-Star GFA GOA GENA1 G-Star DAC DAC10 DAC45 DAC55 DEX20 DEX40 DEX60 DH21 DH31-S DH42 DH62 DHA DH2F DC11 DC53 DM FDAC YEM YEM-K YHD3 YHD27 YHD28 YHD45 YK30 YSS YXR3 YXR33 YXM1 YXM4 YXM42 MH51 MH85 NAK55 NAK80 NP8 NP9 ARK1 H3100 HAP10 HAP40 HAP72 HPM1 HPM2 HPM38 HPM50 HPM57 HPM77 化学成分瑞典：618S 618H 718 718S 718H S136 S136H 8407 8416 STAVAX ASP-23 ASP-30 UHB2311 RAMAX S ALVAR14 ASSAB88 DF3 DF2 ELMAX KM2 HMP41 HOTVAR V4 V10 ORO90 UHB20 UHB4006 UHB4462 UHB5752 UHB5860 UHB5919 UHB8159 UHB709 UHB8550 XW5 XW10 XW41 XW42 Q0R090化学成分奥国：A903 S500 S600 S709 S790 S705 S390PM S590PM S690PM M201 M202 M238 M261 M310 M238ESR W300 M330 M340 M461 W302 W303 W304 W321 W500 K100 K105 K110 K305 K340 K460 K600 K720 K990 VMRM300ESRM310ESR N100 N320 N540 N350 E116 E200 E220 E230 E400 F300 F530 V320 V155 V800 V820 化学成分德国：21NICRMO2 14NICR14 15CRNI6 20CRMO5 18CRNI8 55CR3 50CRV4 42CRMO4 34CRNIMO6 34CRALNI7 40CRNIMOA 638 2711 2316 2316H 2344 2379 2436 2510 2688 2738 1285 1292 2363 2767 2842 3207 1.3343 4125 1.7225 1.0037 1.1210 1.2101 1.1545 1.2080 1.2311 1.2312 1.2343 1.2365 1.2367 1.2550 1.2601 1.2606 1.2714 1.2840 1.2842 1.2885 1.3243 1.3247 1.3343 1.4006 1.4021 1.4034 1.4057 1.4313 1.4462 1.4542 1.4548 1.5752 1.5860 1.5919 1.6582 1.6523 1.7147 1.5920 1.7176 1.7225 1.7220 1.8509 1.8159中国：Cr12 Cr12MoV 6542 W18 W9 3Cr2W8V 15-40CrNiMo 15-42CrMo H13 20CrMnTi 30CrMnTi T8 T8A T10A T12 Y35CA Y12 Y15 Y20 Y30 Y40化学成分美国：P2 P3 P20 H11 H13 H10A F1 F2 F8 L2 L3 L6 M1 M2 M3 M4 M35 M42 M1008 M1020 W110 O1 O2 O6 L2 L3 T1 T15 S1 S7 D2 D3 D6 D7 A2 A3 A6 A8 A10 420 S7 1005 1018 1020 1035 1042 1050 1053 1069 1071 1086 1095 1018 13115 1513 1524 1548 1566 2024 2317 3135 3245 3450 4012 4024 4121 4130 4140 4150 4608 4715 4820 5015 5120 5052 5083 6061 6062 6115 6195 7055 7058 7072 7075 7260 8120 8620 8622 8742 9254 9260 A570.Gr.A K52440钨钢：G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 V30 V40 D30 D40 D50 D60 KE11 SF-05 SF-15 SF-20 SF-30 SF-X K05 K10 K20 YG8 YG9 YG12 YG15 YG20 YG25 YG28 CD650 CD636 CD750 化学成分高速钢：SKH-9 SKH-51 SKH-55 M2 M35 M42 ASP-23 ASP-30 V10 S600 S790铜料：日本三宝红铜银铜铜材紫铜杯士铜铬铜铍铜钨铜合金铜磷青铜锡青铜 C5191 C3604 C3600 C2801 C1100化学成分轧辊钢：9Cr2Mo 9Cr2MoV 718 P20不锈钢：301 302 303 304 310 316 401 410 420 430 440 630 1CR13 2CR13 3CR13 3CR13 4CR13 S31500 S31803 S31220 S36550 321铝板：6061-T651 50527075 8011 8005 8079 6056 6012 5086 2024 1200 1100 5050 1050化学成分易切削结构钢:15S10 1.0710 10S20 1.0721 15S20 15S22 1.0723 35S20 1.0726 45S20 46S20 1.0727 60S20 60S22 1.0728 10SPb20 1.0722 35SPb 1.0756 45SPb20 46SPb20 1.0757 60SPb20 60SPb22 1.0758 9SMn28 11SMn30 1.0736 9SMn36 11SMn37 1.0736 9SMnPb28 11SMnPb30 1.0718 9SMnPb36 11SMnPb37 1.0737 9S20 11SMn28 11SMnPb28 12SMnPb35 12SMn35 10Pb20 10SPb20 17SMn2035S20 35SMn20 44SmN28 46S20 …….冷镦钢和冷挤压钢：Cq15 C15C 1.1132 Cq22 C22C 1.1152 Cq35 C35C 1.1172 Cq45 C45C 1.1192 38Cr1 1.7001 46Cr1 1.7002 38Cr1 1.700 46Cr2 1.7006 15Cr3 1.7015 34Cr4 1.7033 37Cr4 1.7034 41Cr4 1.7035 25CrMo4 1.7218 34CrMo4 1.7220 42CrMo4 1.7225 20MoCr4 1.7321 16MnCr5 1.7131 15CrNi6 1.5919 30CrNiMo8 1.6580 34CrNiMo6 1.6582 20NiCrMo2-21 21NiCrMo2 1.6523 CC4X CC4A CC8S CC8A CC11X CC11A CE10 CE15E4 CE16E4 CE20E4 20CRE4 16MnCr5E 18MnCr4E 18CrMo4E 20NiMo2E CE20E4 CE28E4 CE35E4 CE40E4 CE45E4 42Mn6E 37Cr2E 46Cr2E 34Cr4E 37Cr4e 41Cr4E 41Cr4E 36Mo3E 25CrMo4e 34CrMo4e 42CrMo4e 41CrNiMo2E 41NiCrMo7E31CrNiMo8e CE20BG1 CE20BG2 CE28B CE35B 35MnB5E 37CrBLE …弹簧钢和轴承钢：C67ECK67 1.1231 C75E CK75 1.1248 C85E CK85 1.1269 C10E CK101 1.1274 38Si6 1.5022 38Si7 1.5023 46Si7 1.5024 51Si7 1.5025 55Si7 56Si7 1.5026 65Si7 1.5028 71Si7 1.5029 60SiMn5 1.5142 51MnV7 1.5225 54SiCr6 1.7102 60SiCr7 1.7108 67SiCr5 1.7103 55Cr3 1.7176 51CrC4 50CrV4 1.8159 58CrV4 1.8161 ......刀具用钢：SKS11 SKS2 SKS21 SKS5 SKS7 SKS81 SKS8 ……….耐冲击工具钢：SKS4 SKS41 SKS43 SKS44……….冷作模具钢：SKS3 SKS31 SKS93 SKS94 SKS95 SKD1 SKD2 SKD10 SKD12 SKD11 ……….热作模具钢：SKD4 SKD5 SKD6 SKD61 SKD62 SKD7 SKD8 SKT3 SKT4 SKT6…………）日本JIS标准结构钢牌号：SS330 SS400 SS490 SS540 SCM4400A SM400B SM400C SM490A SM490 SM490C SM490YA SM490YB SM570 CUP-Ten CUP-Ten60 FTW-52 FTW-60 FTW-70 HI-Z HI-Z Super HI-YAW-TEN HTP-52W NK-HITEN50 NK-HITE60 NK-HITEN70 NK-HITEN80 NK-HTEN100 RiverAce60 RiverAce70 RiverAce80 Welten50 Welten60 Welten70 Welten80 Welten80C Welten100N YAW-TEN50 Zirten SMA400AW SMA400BW SMA400CW SMA400AP SMA400BP SMA400CP SMA490AW SMA490BW SMA490CW SMA490AP SMA490BP SMA490CP SWA570W SWA570P SPA-H APA-C SPV315 SPV355 SPV410 SPV410 SPV450 SPV490 SPV235 SG255 SG295 SG325 SG365 SGV410 SGV450 SGV480 SGV42 SGV46 SGV49 SLA235A ALA235B ALA325B ALA325B ALA365 ALA410 SL2N255 SL3N255日本JIS标准机械结构用钢牌号：S10C S12C S15C S17C S20C S22C S25C S28C S30C S33C S35C S38C S40C S43C S45C S48C S50C S53C S58C S09CK S15CK S20CK日本JIS标准淬透性结构用钢牌号：SMn420H SMn433H SMn438H SMn4443H SCr415H SCr420H SCr435H SCr440HSCM415H SCM418H SCM420H SCM435H SCM440H SCM822H SNC415H SNC631H SNC220H SNC420H日本JIS标准易切削钢牌号：SUM11 SUN12 SUM21 SUM22 SUM22L SUM23 SUM23L SUM24L SUM25 SUM31 SUM31L SUM41 SUM42 SUM43 …………日本JIS标准合金钢牌号：SNB5 SNB7 SNB16 SNB21-1-5日本JIS标准轴承钢牌号：SUP3 SUP6 SUP7 SUP9 SUP9A AUP10 AUP11A AUP12 AUP13 SUJ1 SUJ2 SUJ3 SUJ4 SUJ5日本JIS标准不绣钢耐热钢牌号：SUS201 SUS202 SUS301 SUS302 SUS303 SUS303Se SUS303Cu SUS304 SUS304L SUS304N1 SUS304N2 SUS304LN SUS304J3 SUS305 SUS309S SUS309S SUS310S SUS316 SUS316L SUS316NSUS316LN SUS316F SUS317 SUS317L SUS317LN SUS317J1 SUS836L SUS890L SUS321 SUS347 SUSXM7 SUSXM15J1 SUS329J1 SUS329J1 SUS329J1 SUS329J4L SUS405 SUS410L SUS430 SUS430F SUS44J1 SUUSXM27 SUS403 SUS410 SUS410J1 SUS410F2 SUS416 SUS420J1 SUS420J2 SUS420F SUS420F2 SUS431 SUS440A SUS440F SUS630SUS631 SUS304TP SUS304HTP SUS309TP SUS310TP SUS890LTP SUS347HTP SUS304TKA SUS304TKC SUS316TKA SUS316TK SUS321TKA SUSTKC SUS420J1TKA SUS430TKA SUSTKC SUH31 SUH35 SUH36 SUH37 SUH38 SUH309 SUH310 SUH330 SUH660 SUH661 SUH446 SUH1 SUH3 SUH4 SUH11日本JIS标准高温合金钢耐蚀钢牌号：NCF600 NCF601 NCT625 NCF690 NCF718 NCF718 NCF750 NCF751 NCE800 NCF800H NCF825 NCF80A NCF600TP NCF600TB NCF625TP NCF800TP NCF825TP NCF825TB日本JIS标准工具钢牌号：SK140 SK120 SK105 SK95 SK90 SK85 SK80 SK75 SK70 SK65 SK60日本JIS标准高速钢牌号：SKH2 SKH3 SKH4 SKH10 SKH40 SKH50 SKH51 SKH52 SKH53 SKH54 SKH55 SKH56 SKH57 SKH58 SKH59………日本JIS标准特殊钢中空钢牌号：SK3M SK3M SK4M SK5M SK6M SK7M SK2M SK5M SKS51M SKS81MSKS95M SKC3 SKC11 SKC24 SKC25 SKC31日本JIS标准钨钢（硬质合金钢）牌号：切削工具用：P01 P15 P10 P20 P30 P40 M10 M20 M30 M40 K01 K10 K20 K30………拉丝模和顶尖工具用：V10 V20 V30……….矿山的质地工具用：,E1 E2 E4 E5………超微粒硬质合金：Z01 Z10 Z20 Z30 …………A1 A40 CC F0 F1 G2 G3 G5 G8 G10E H1 H2 H3 ST10E ST15E ST20E ST25E ST30E ST40E T12A T3S U1 U10E AC720 AC805 AC835………日本JIS标准结构用铸钢牌号:SC360 SC37 SC410 SC42 SC450 SC46 SC480 SC49 SC360 SC410 SC450 SC480 200-400 200-400W 230-450 230-450W 270-480W 340-550 340-550W SCW410 SCW42 SCW450 SCW46 SCW480 SCW49 SCW63SCC3 SCC5 SCMn1 SCMn2 SCMn3 SCMn5 SCMnCr2…….SCC3A SCC3B……….瑞典SS标准,碳素结构钢:1211 1225 1226 1232 1233 1234 1250 1265 1300 1310 1311 1312 1313 1330 1331 1332 1350 1357 1370 1410 1411 1412 1413 1414 1421 1422 1423 1424 1430 1431 1432 1434 1435 1450 1500 1510 1550 1550 1572 1600 1650 1655 1660 1665 1672 1674 1678合金结构钢:2085 2090 2101 2102 2103 2106 2107 2108 2110 2112 2114 2116 2117 2120 2121 2122 2127 2128 2130 2131 2132 2134 2135 2142 2143 2144 2145 2165 2168 2172 2173 2174 2203 2216 2218 2225 2228 2230 2231 2233 2243 2240 2244 2245 2253 2254 2258 2506 2511 2512 2520 2523 2530 2532 2534 2536 2541 2316 2615 2624 2625 2632 2634 2642 2644 2652 2654 2662 2664 2942 2940……弹簧钢: 1770 1774 1778…….易切削钢: 1912 1214 1922 1926 1940 1957 1973……..不绣钢和耐热钢：2301 2302 2303 2304 2317 2320 2321 2322 2323 2324 2325 2326 2327 2328 2331 2332 2333 2337 2338 2340 2343 2346 2347 2348 2350 2352 2353 2357 2360 2361 2366 2367 2368 2370 2371 2372 2374 7376 2377 2378 2380 2382 2383 2384 2387 2388 2562 2564 2570 2584 2662 2301-02 2301-22 2301-23 2302-02 2302-03 2303-02 2303-03 0303-04 2303-08 2304-02 2304-08 2317-03 2321-02 2321-03 2324-02 2325-02 2326-02 2326-22 2326-23 2326-26 2326-28 2340-04 2343-04 2343-22 2343-23 2343-24 2343-26 2343-27 2343-28 2343-29 2346-02 2346-02 2347-02 2347-22 2347-23 2347-26 2347-27 2347-28 2347-29 2348-02 2348-22 2348-23 2348-24 2348-25 2348-27 2348-28 2348-29 2350-02 2350-27 2350-28 2350-29 2352-02 2352-27 2352-29 2353-02 2353-28 2353-29 2366-27 2366-28 2366-29 2367-02 2367-28 2367-29 2370-02 2370-27 2370-28 2370-29 2371-02 2371-27 2371-29 2374-02 2374-27 2374-28 2374-29 2375-02 2380-02 2380-03 2570-03 2570-04 2570-04 2750-08 2375-27 2375-28 2375-29瑞典SS标准,碳素工具钢：1770 1778 1880 1885………..合金工具钢: 2092 2140 2242 2260 2310 2312 2314 2511 2514 2540 2550 2700 2705 2710 2730 2900 2940………高速工具钢：2715 2716 2722 2723 2724 2725 2736 2750 2752 2754 2756 2782 HSP-6 HSP-11 HSP-15 HSP-16 SHP-17 HSP41 HSP-42 ASP-23PM ASP-30PM ASP-60PM ASP-23 ASP-30 ASP-60….….工具钢及硬质合金钢：2726 2727 2736 2750 2752 2754 2756 2782 CG20 CG35 CG40 CG60 CN02 CN10 CN30 CN40 CS05 CS10 CS20 CS35 CT30 CT45 CT50 CT60 CT75 CT60 CT75 CT85 F02 H05 H10 H20 HIP HM HML RIP R4 S2 S4 S6 SIP SH SM …….涂层硬质合金：GC015 GC135 GC315 GC1025 PO5 P35 K05 K20 P25 P45 M15 M20 K05 K25 P10 P35 K20 ………..末涂层硬质合金：B1 B2 B23 B45 G4 G5 G27 K40 M40 H5 H13 K01 K10 H20 K20 H30 K30 H45 HX K10 K30 M10 M20 S1F P01 P15 S1G P01 P10 S2 P10 P20 S4 M20 P20 P30 S6 M30 P10 P40 S25M SU41 K10 K20 M10 M20 SecoticKSecticTP15 SecticTP25 Secotic TP35….非合金钢和合金钢牌号:1305 1306 1505 1606 2120 2133 2172 2183 2223 2224 2225………不绣耐蚀铸钢：2302 2324 2333 2343 2343-12 2366 2377 2385 2387 2564 2564……..瑞典灰铸铁:0110-00 0115-00 0125-00 0130-00 0140-00 215 217 219 221 223 ….球墨铸铁: 0717-00 0717-02 0717-15 0722-00 0727-02 0732-01 0772-00 0776-03 ….可锻铸铁: 0814-00 0815-00 0852-00 0854-00 0856-00 0862-03 0864-03……..经营美国“ALCOA”优质铝板、铝棒范围：6061-T6,7075-T651,A5052-H32,7075-T6,6061-T651,5052-H112,5086-H32,5083-H111,5083-H112,1100,1050,1 060 6063,5083,5086,2011,2017,2024,3003,7022,7050,7072,6060,6061,7075,5052等合金铝板/棒/管材等★经营国产优质铝板、铝棒范围:6061-T6,7075-T651,A5052-H32,7075-T6,6061-T651, 5083-H111, 1050,1060,6061,7075,5052,6063,5083, 5086,6062,6082-T6,6262,5154,5754,5356,3000,491,LY12,LC4,1XXX,7009等合金铝板/棒/管材等常备现货铝板/厚度如下:6061: 2mm-280mm; 7075: 2mm-180mm 5052: 1mm-80mm 5083: 8mm-80mm7075-T651: 10mm-180mm 6063: 2mm-280mm 2017: 4mm-80mm6061-T6: 3mm-280mm A5052-H32: 0.5mm-10mm 5083-H111: 1mm-10mm合金铸铁: 0457-00 0466-00 0512-00 0513-00 0747-03 0747-04 ……瑞典常用钢:618 618S 718 718S 718H S136 S136H 8407 8416 STAVAX UHB33 RAMAXS ALVAR14 ASSAB88 DF3 DF2 ELMAX KM2 HMP41 HOTVAR V4 V10 ORO90 UHB20 UHB4006 UHB4462 UHB5752 UHB5860 UHB5919 UHB8159 UHB709 UHB8550 ASP-23 ASP-30 ASP-60 ………….上海扩进模具材料有限公司大量销售模具钢，进口模具钢，高速钢，粉末高速钢，钨钢，铝材，铜材，铝板，铝棒如：日本 :PX4 PX5 PDS-3 PDS-5 PAK90 PD555 PD613 SGT S50C SC5C SUS303 SUS304 SUS410 SUS420 SUS630 SCM440 SMC420 SUP9 SK3 SK4 SKD4 SKD5 SKD7 SKD8 SKD11 SKD12 SKD61 SKD62 SKH-9 SKH-51 SKH-55SKH57 SKH59 SKT4 SKS3 SKS41 SLD SLD8 SLD10 SM400A SNC815 SPHD SS41 SS330 SS400 SS490 S-Star GFA GOA GENA1 G-Star DAC DAC10 DAC45 DAC55 DEX20 DEX40 DEX60 DH21 DH31-S DH42 DH62 DHA DH2F DC11 DC53 DM FDAC YEM YEM-K YHD3 YHD27 YHD28 YHD45 YK30 YSS YXR3 YXR33 YXM1 YXM4 YXM42 MH51 MH85 NAK55 NAK80 NP8 NP9 ARK1 H3100 HAP10 HAP40 HAP72 HPM1 HPM2 HPM38 HPM50 HPM57 HPM77 化学成分瑞典：618S 618H 718 718S 718H S136 S136H 8407 8416 STAVAX ASP-23 ASP-30 UHB2311 RAMAX S ALVAR14 ASSAB88 DF3 DF2 ELMAX KM2 HMP41 HOTVAR V4 V10 ORO90 UHB20 UHB4006 UHB4462 UHB5752 UHB5860 UHB5919 UHB8159 UHB709 UHB8550 XW5 XW10 XW41 XW42 Q0R090化学成分奥国：A903 S500 S600 S709 S790 S705 S390PM S590PM S690PM M201 M202 M238 M261 M310 M238ESR W300 M330 M340 M461 W302 W303 W304 W321 W500 K100 K105 K110 K305 K340 K460 K600 K720 K990 VMRM300ESRM310ESR N100 N320 N540 N350 E116 E200 E220 E230 E400 F300 F530 V320 V155 V800 V820 化学成分德国：21NICRMO2 14NICR14 15CRNI6 20CRMO5 18CRNI8 55CR3 50CRV4 42CRMO4 34CRNIMO6 34CRALNI7 40CRNIMOA 638 2711 2316 2316H 2344 2379 2436 2510 2688 2738 1285 1292 2363 2767 2842 3207 1.3343 4125 1.7225 1.0037 1.1210 1.2101 1.1545 1.2080 1.2311 1.2312 1.2343 1.2365 1.2367 1.2550 1.2601 1.2606 1.2714 1.2840 1.2842 1.2885 1.3243 1.3247 1.3343 1.4006 1.4021 1.4034 1.4057 1.4313 1.4462 1.4542 1.4548 1.5752 1.5860 1.5919 1.6582 1.6523 1.7147 1.5920 1.7176 1.7225 1.7220 1.8509 1.8159中国：Cr12 Cr12MoV 6542 W18 W9 3Cr2W8V 15-40CrNiMo 15-42CrMo H13 20CrMnTi 30CrMnTi T8 T8A T10A T12 Y35CA Y12 Y15 Y20 Y30 Y40化学成分美国：P2 P3 P20 H11 H13 H10A F1 F2 F8 L2 L3 L6 M1 M2 M3 M4 M35 M42 M1008 M1020 W110 O1 O2 O6 L2 L3 T1 T15 S1 S7 D2 D3 D6 D7 A2 A3 A6 A8 A10 420 S7 1005 1018 1020 1035 1042 1050 1053 1069 1071 1086 1095 1018 13115 1513 1524 1548 1566 2024 2317 3135 3245 3450 4012 4024 4121 4130 4140 4150 4608 4715 4820 5015 5120 5052 5083 6061 6062 6115 6195 7055 7058 7072 7075 7260 8120 8620 8622 8742 9254 9260 A570.Gr.A K52440钨钢如：G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 V30 V40 D30 D40 D50 D60 KE11 SF-05 SF-15 SF-20 SF-30 SF-X K05 K10 K20 YG8 YG9 YG12 YG15 YG20 YG25 YG28 CD650 CD636 CD750 化学成分高速钢:SKH-9 SKH-51 SKH-55 M2 M35 M42 ASP-23 ASP-30 V10 S600 S790铜料如：日本三宝红铜银铜铜材紫铜杯士铜铬铜铍铜钨铜合金铜磷青铜锡青铜 C5191 C3604C3600 C2801 C1100化学成分轧辊钢：9Cr2Mo 9Cr2MoV 718 P20不锈钢：301 302 303 304 310 316 401 410 420 430 440 630 1CR13 2CR13 3CR13 3CR13 4CR13 S31500 S31803 S31220 S36550 321铝板：6061-T651 50527075 8011 8005 8079 6056 6012 5086 2024 1200 1100 5050 1050化学成分易切削结构钢:15S10 1.0710 10S20 1.0721 15S20 15S22 1.0723 35S20 1.0726 45S20 46S20 1.0727 60S20 60S22 1.0728 10SPb20 1.0722 35SPb 1.0756 45SPb20 46SPb20 1.0757 60SPb20 60SPb22 1.0758 9SMn28 11SMn30 1.0736 9SMn36 11SMn37 1.0736 9SMnPb28 11SMnPb30 1.0718 9SMnPb36 11SMnPb37 1.0737 9S20 11SMn28 11SMnPb28 12SMnPb35 12SMn35 10Pb20 10SPb20 17SMn2035S20 35SMn20 44SmN28 46S20 …….冷镦钢和冷挤压钢:Cq15 C15C 1.1132 Cq22 C22C 1.1152 Cq35 C35C 1.1172 Cq45 C45C 1.1192 38Cr1 1.7001 46Cr1 1.7002 38Cr1 1.700 46Cr2 1.7006 15Cr3 1.7015 34Cr4 1.7033 37Cr4 1.7034 41Cr4 1.7035 25CrMo4 1.7218 34CrMo4 1.7220 42CrMo4 1.7225 20MoCr4 1.7321 16MnCr5 1.7131 15CrNi6 1.5919 30CrNiMo8 1.6580 34CrNiMo6 1.6582 20NiCrMo2-21 21NiCrMo2 1.6523 CC4X CC4A CC8S CC8A CC11X CC11A CE10 CE15E4 CE16E4 CE20E4 20CRE4 16MnCr5E 18MnCr4E 18CrMo4E 20NiMo2E CE20E4 CE28E4 CE35E4 CE40E4 CE45E4 42Mn6E 37Cr2E 46Cr2E 34Cr4E 37Cr4e 41Cr4E 41Cr4E 36Mo3E 25CrMo4e 34CrMo4e 42CrMo4e 41CrNiMo2E 41NiCrMo7E31CrNiMo8e CE20BG1 CE20BG2 CE28B CE35B 35MnB5E 37CrBLE …..弹簧钢和轴承钢:C67ECK67 1.1231 C75E CK75 1.1248 C85E CK85 1.1269 C10E CK101 1.1274 38Si6 1.5022 38Si7 1.5023 46Si7 1.5024 51Si7 1.5025 55Si7 56Si7 1.5026 65Si7 1.5028 71Si7 1.5029 60SiMn5 1.5142 51MnV7 1.5225 54SiCr6 1.7102 60SiCr7 1.7108 67SiCr5 1.7103 55Cr3 1.7176 51CrC4 50CrV4 1.8159 58CrV4 1.8161 ......刀具用钢：SKS11 SKS2 SKS21 SKS5 SKS7 SKS81 SKS8 ……….耐冲击工具钢：SKS4 SKS41 SKS43 SKS44……….冷作模具钢：SKS3 SKS31 SKS93 SKS94 SKS95 SKD1 SKD2 SKD10 SKD12 SKD11 ……….热作模具钢：SKD4 SKD5 SKD6 SKD61 SKD62 SKD7 SKD8 SKT3 SKT4 SKT6…………）日本JIS标准结构钢牌号:SS330 SS400 SS490 SS540 SCM4400A SM400B SM400C SM490A SM490 SM490C SM490YA SM490YB SM570 CUP-Ten CUP-Ten60 FTW-52 FTW-60 FTW-70 HI-Z HI-Z Super HI-YAW-TEN HTP-52W NK-HITEN50 NK-HITE60 NK-HITEN70 NK-HITEN80 NK-HTEN100 RiverAce60 RiverAce70 RiverAce80 Welten50 Welten60 Welten70 Welten80 Welten80C Welten100N YAW-TEN50 Zirten SMA400AW SMA400BW SMA400CW SMA400AP SMA400BP SMA400CP SMA490AW SMA490BW SMA490CW SMA490AP SMA490BP SMA490CP SWA570W SWA570P SPA-H APA-C SPV315 SPV355 SPV410 SPV410 SPV450 SPV490 SPV235 SG255 SG295 SG325 SG365 SGV410 SGV450 SGV480 SGV42 SGV46 SGV49 SLA235A ALA235B ALA325B ALA325B ALA365 ALA410 SL2N255 SL3N255日本JIS标准机械结构用钢牌号:S10C S12C S15C S17C S20C S22C S25C S28C S30C S33C S35C S38C S40C S43C S45C S48C S50C S53C S58C S09CK S15CK S20CK日本JIS标准淬透性结构用钢牌号:SMn420H SMn433H SMn438H SMn4443H SCr415H SCr420H SCr435H SCr440H SCM415H SCM418H SCM420H SCM435H SCM440H SCM822H SNC415H SNC631H SNC220H SNC420H日本JIS标准易切削钢牌号:SUM11 SUN12 SUM21 SUM22 SUM22L SUM23 SUM23L SUM24L SUM25 SUM31 SUM31L SUM41 SUM42 SUM43 …………日本JIS标准合金钢牌号:SNB5 SNB7 SNB16 SNB21-1-5日本JIS标准轴承钢牌号:SUP3 SUP6 SUP7 SUP9 SUP9A AUP10 AUP11A AUP12 AUP13 SUJ1 SUJ2 SUJ3 SUJ4 SUJ5日本JIS标准不绣钢耐热钢牌号:SUS201 SUS202 SUS301 SUS302 SUS303 SUS303Se SUS303Cu SUS304 SUS304L SUS304N1 SUS304N2 SUS304LN SUS304J3 SUS305 SUS309S SUS309S SUS310S SUS316 SUS316L SUS316NSUS316LN SUS316F SUS317 SUS317L SUS317LN SUS317J1 SUS836L SUS890L SUS321 SUS347 SUSXM7 SUSXM15J1 SUS329J1 SUS329J1 SUS329J1 SUS329J4L SUS405 SUS410L SUS430 SUS430F SUS44J1 SUUSXM27 SUS403 SUS410 SUS410J1 SUS410F2 SUS416 SUS420J1 SUS420J2 SUS420F SUS420F2 SUS431 SUS440A SUS440F SUS630SUS631 SUS304TP SUS304HTP SUS309TP SUS310TP SUS890LTP SUS347HTP SUS304TKA SUS304TKC SUS316TKA SUS316T SUS321TKA SUSTKC SUS420J1TKA SUS430TKA SUSTKC SUH31 SUH35 SUH36 SUH37 SUH38 SUH309 SUH310 SUH330 SUH660 SUH661 SUH446 SUH1 SUH3 SUH4 SUH11日本JIS标准高温合金钢耐蚀钢牌号:NCF600 NCF601 NCT625 NCF690 NCF718 NCF718 NCF750 NCF751 NCE800 NCF800H NCF825 NCF80A NCF600TP NCF600TB NCF625TP NCF800TP NCF825TP NCF825TB日本JIS标准工具钢牌号:SK140 SK120 SK105 SK95 SK90 SK85 SK80 SK75 SK70 SK65 SK60日本JIS标准高速钢牌号:SKH2 SKH3 SKH4 SKH10 SKH40 SKH50 SKH51 SKH52 SKH53 SKH54 SKH55 SKH56 SKH57 SKH58 SKH59………..日本JIS标准特殊钢中空钢牌号:SK3M SK3M SK4M SK5M SK6M SK7M SK2M SK5M SKS51M SKS81MSKS95M SKC3 SKC11 SKC24 SKC25 SKC31日本JIS标准钨钢（硬质合金钢）牌号:切削工具用：P01 P15 P10 P20 P30 P40 M10 M20 M30 M40 K01 K10 K20 K30。

ABS产品型号及物性

ABS产品型号及物性塑料原料ABS/AG12A0/台湾化纤通用级用途:鞋跟，玩具，时钟外壳，音响外壳，手提箱，板状制品，冰箱内壳。

特性：高耐冲击性，一般成型熔体流动速率: 1.6 g/10min | 密度: 1.04 g/cm3 | 缺口冲击强度: 30 | 拉伸强度: 50 MPa | 弯曲强度:74 MpaABS/AG15A1/台湾化纤通用级用途:鞋跟，玩具，时钟外壳，音响外设，手提箱。

特性:特性：高光泽性、高耐冲击性。

特性:特性：透明。

特性:特性：难燃性。

AG102中文资料

Units
MHz dB dB dB dBm dBm dB mA V
Min
60 13
+33 55
Typ
900 14 10 27 +18 +36 2.1 70 4.5
Max
3000 16
90
Test conditions unless otherwise noted. 1. T = 25º C, Supply Voltage = +4.5 V, Frequency = 900 MHz, 50 ohm system. 2. 3OIP measured with two tones at an output power of +2 dBm/tone separated by 10 MHz. The
Units
MHz dB dB dB dBm dBm dB V mA
Typical
900 1900 900 1900
14 12.8 14 12.5
-10
-9
-10
-9
-27 -22 -28 -19
+18 +18 +16 +16
+36 +36 +35 +35
2.1
2.2
2.0
2.2
+4.5
+3.3
70
68
Ordering Information
Part No. Description
AG102
GaAs MMIC Gain Block
AG102-PCB 0.8 – 2.6 GHz Fully Assembled Application Circuit
Specifications and information are subject to change without notice.

NHD-240128BZ-NSW-BTW, 规格书,Datasheet 资料

NHD‐240128BZ‐NSW‐BTW Graphic Liquid Crystal Display ModuleNHD‐ Newhaven Display240128‐ 240 x 128 pixelsBZ‐ ModelN‐ TransmissiveSW‐ Side White LED BacklightB‐ STN ‐ Blue (‐)T‐ 12:00 viewW‐ Wide Temperature (‐20°C ~ +70°C)RoHS CompliantNewhaven Display International, Inc. 2511 Technology Drive, Suite 101Elgin IL, 60124Ph: 847‐844‐8795 Fax: 847‐844‐8796nhtech@Document Revision HistoryRevision Date Description Changed by0 10/5/2007 Initial Release ‐1 6/4/2008 Update table of contents CL2 4/22/2010 User guide reformat BE3 9/20/2010 Pin description pin18/electrical characteristics updated BE4 11/30/2010 Update Mechanical Drawing / Block Diagram AK5 6/13/2011 Electrical characteristics/contrast updated BE6 1/24/2012 Pin description updated AKFunctions and Features•240 x 128 pixels•Built‐in RA8835 controller•+5.0V Power Supply•1/128 duty, 1/12 bias•RoHS CompliantPin Description and Wiring DiagramPin No. Symbol ExternalFunction DescriptionConnection1 VSS Power Supply Ground2 VDD Power Supply Power supply for logic (+5.0V)3 V0 Adj. Power Supply Power Supply for contrast(approx 19.2V)4 A0 MPU Register Select signal.0: data; 1: instruction5 R/W MPU Read/Write select signal, R/W=1: Read R/W=0: Write6 E MPU Operation enable signal. Falling edge triggered.7‐10 DB0‐DB3 MPU Four low order bi‐directional three‐state data bus lines.These four are not used during 4‐bit operation.11‐14 DB4‐DB7 MPU Four high order bi‐directional three‐state data bus lines.15 /CS MPU Active LOW Chip Select Signal16 68/80 MPU Interface Select Pin. 0: 8080 Family 1: 6800 Family17 /RESET MPU Active LOW reset signal18 VEE Power Supply Positive voltage supply output (+20V)19 LED+ Power Supply Power supply for LED Backlight(+3.0V)20 LED‐ Power Supply Ground for BacklightRecommended LCD connector: 2.54mm pitch pinsBacklight connector: ‐ Mates with: ‐Electrical CharacteristicsItem Symbol Condition Min.Typ.Max. Unit Operating Temperature Range Top Absolute Max‐20‐+70 ⁰C Storage Temperature Range Tst Absolute Max‐30‐+80 ⁰C Supply Voltage VDD 4.7 5.0 5.5 V Supply Current IDD VDD=5.0V‐ 3.5 5.5 mA Supply for LCD (contrast) VDD‐V0 Ta=25°‐‐14.2‐ V “H” Level input VIH 2.2‐VDD V “L” Level input VIL 0‐0.6 V “H” Level output VOH 2.4‐‐ V “L” Level output VOL ‐‐0.4 VBacklight Supply Voltage Vled ‐‐ 3.0‐ V Backlight Supply Current Iled Vled=3.0V‐36‐ mAOptical CharacteristicsItem Symbol Condition Min.Typ.Max. Unit Viewing Angle ‐ Vertical AV Cr ≥2‐60‐ ⁰ Viewing Angle ‐ Vertical AV Cr ≥2‐35‐ ⁰ Viewing Angle – Horizontal AH Cr ≥2 ‐40‐ ⁰ Viewing Angle ‐ Horizontal AH Cr ≥2‐40‐ ⁰ Contrast Ratio Cr ‐6‐ ‐ Response Time (rise) Tr ‐‐150250 ms Response Time (fall) Tf ‐‐150250 msController InformationBuilt‐in RA8835. Download specification at /app_notes/RA8835.pdfTable of CommandsTiming CharacteristicsExample Initialization Program//‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ sbit A0 = P3^0;sbit RW = P3^7;sbit E = P3^4;sbit CS = P3^1;sbit IM = P3^6;sbit RST= P3^2;//‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ void Writecom(int A){CS = 0;RW = 0;A0 = 1;E = 1;P1 = A;E = 1;}void Write(int A){CS = 0;RW = 0;A0 = 0;E = 1;P1 = A;E = 1;}//‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ void init(){IM = 1;RST = 0;delay(10);RST = 1;delay(100);Writecom(0x40);Write(0x30);Write(0x87);Write(0x07);Write(0x1D);Write(0x50);Write(0x80);Write(0x1E);Write(0x00);Writecom(0x44);Write(0x00);Write(0x00);Write(0x80);Write(0x00);Write(0x40);Write(0x80);Write(0x00);Write(0x00);Write(0x00);Write(0x00);Write(0x5A);Write(0x00);Write(0x5B);Write(0x0C);Write(0x4C);Write(0x46);Write(0xB0);Write(0xB0);Write(0x42);Write(0x00);for(a = 0; a < 3840; a++){Write(0x00);}Writecom(0x46);Write(0x60);Write(0x09);Writecom(0x42);Write(0x00);for(a = 0; a < 3840; a++){Write(0x00);}Writecom(0x59);Write(0x04);}//‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐Quality InformationTest Item Content of Test Test Condition Note High Temperature storage Endurance test applying the highstorage temperature for a long time.+80⁰C , 200hrs2Low Temperature storage Endurance test applying the low storagetemperature for a long time.‐30⁰C , 200hrs1,2High Temperature Operation Endurance test applying the electric stress(voltage & current) and the high thermalstress for a long time.+70⁰C 200hrs2Low Temperature Operation Endurance test applying the electric stress(voltage & current) and the low thermalstress for a long time.‐20⁰C , 200hrs1,2High Temperature / Humidity Operation Endurance test applying the electric stress(voltage & current) and the high thermalwith high humidity stress for a long time.+60⁰C ,90% RH , 96hrs 1,2Thermal Shock resistance Endurance test applying the electric stress(voltage & current) during a cycle of lowand high thermal stress. ‐20⁰C,30min ‐> 25⁰C,5min ‐>70⁰C,30min = 1 cycle10 cyclesVibration test Endurance test applying vibration tosimulate transportation and use. 10‐55Hz , 15mm amplitude.60 sec in each of 3 directionsX,Y,ZFor 15 minutes3Static electricity test Endurance test applying electric staticdischarge. VS=800V, RS=1.5kΩ, CS=100pFOne timeNote 1: No condensation to be observed.Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH.Note 3: Test performed on product itself, not inside a container.Precautions for using LCDs/LCMsSee Precautions at /specs/precautions.pdfWarranty Information and Terms & Conditions /index.php?main_page=terms。