7G2000_040427菲亚特DV规范
DV功能测试规范
文件名称
DV 功能测试规范
编 号: -----001 制订日期: 修订日期: 版 本: 1.0 页 次: 5 OF 11
序 测试项目 不良
号
等级
测试规格
描述
不良判定
(√ ×)
30 LCD 横纹干扰 B 以 PA 检验标准定
将频率 50HZ 与 60HZ 转换，使用 50HZ 拍摄白色墙壁，照 片上不可有波浪横纹干扰，需确认所有分辨率
25 闪光充电电压 B 依各机型设计规格定 用电压表测试充满电时电容上电压符合设计规格要求
26 闪光拍照距离 B 依各机型设计规格定 不同距离影像品质达同类产品设计标准
27 闪光寿命测试
连续闪光拍照 3000 次 连续闪光拍照 3000 次，亮度无明显减退，照怎品质良好
28 闪光指数 B 依各机型设计规格定 以 EV 表测试为准，达同类产品设计标准
5. 插卡后再开机工作正常
外置记忆卡兼
7
容
B 以相机设计规格定
各种能技术支持的媒体卡在不同的 WINDOWS 系统中均能 兼容
8 内置记忆体 B 各 Windows 系统
1. 重复关机开机录制/复制/删除能正常操作 2. 下载测试能正常操作
内存可拍照张
9
数
C 以设计要求为准
固定景物，连续拍摄至内存满为止，记录可拍摄的最多张数， 并切换各分辨率和影像品质各拍摄 5 次，取平均值
42 四角阴影 B 以平行光源箱拍白纸 注意四角不可有明显阴影，无彩点杂点
43 光源频率测试 B 以光源箱标准频率为准 分别测试 50HZ/60HZ，LCD、PC Camera 无屏闪，无波纹
44 50HZ AE 振荡 B 光源箱、日光灯，日光 测试各种光源环境无 AE 振荡现象
Fiat9.57409标准中文版
菲亚特9.57409标准铁基材料制品表面上的锌镍合金镀层目的：规定了锌镍合金镀层必须满足铁基制品要求的特性；规定了应遵循的流程及检测这些特性所使用的设备；提供该类涂层在图纸上的表示方法A：试验设备参看该文本中引入的所要求的必备设备（见表B）该类仪器可能会被其它特性、精度及可重复性相当的或更优的设备而替换B：参考标准（略）C：附件清单1.）设备规格表2.）螺栓润滑的方法1.概述1.1该采购标准涉及铸铁、碳钢或合金钢制品表面上所应用的新镍合金镀层的型号、特性及试验，其主要目的是启到耐腐蚀的防护作用1.2应用领域1.2.1新镍合金镀层可以应用于较小项目的大面积区域或底盘上，也可以应用在螺栓上货较大的铁基制品上（如支架、支撑器等）1.2.2上述提及的镀层一般多用于要求较高耐腐蚀值的电解镀锌，以避免产生红锈和白锈1.2.3就像电解镀锌层一样，锌镍合金镀层不能用于耐张应力（R）≥1500N/mm2的钢制品上，也不能用于R≥1200N/mm2且功能等级为1的钢制品1.3分类（级）、命名以及图纸上的表示1.3.1六价铬的注意事项为了遵循关于车辆寿命终期的欧洲指引要求（2000/53/CE），基于生态及环保等原因，自2007年7月1日起，在采购标准9.01102附件CK中已经采取了车辆中必须彻底消除铬化物（含六价铬）基于此，自2006年7月1日起，该采购标准中所有包含六价铬的涂层都将被废止并不得再向菲亚特汽车公司供给在过渡期间，菲亚特汽车关于欧洲市场所采取的干预措施如下：●对于新的型号，自2004年1月1日起首次批准的型号，在所有新出图纸中应完全移除六价铬（含传动零部件）注意：自2004年1月1日起移除六价铬的义务并不适用于以下几个方面：——衍生车厢的车辆（例如厢式货车、皮卡、SW等）——翻新、改装——重塑——首次推出时未预见的批准的引擎型号的延伸，2004年7月1日之前所首次批准的型号●对于新出的图纸，涉及2003年12月已经生产的型号，以及已经处于生产中或后续处理的零部件图纸（含螺栓及标准件），即使是2004年7月1日之后首次批准的新型号，都应自2006年7月1日起，完全移除六价铬●特别应注意的是，关于后续处理的零部件（含螺栓及标准件），如果在图纸中或修订表中，有预见不含六价铬的涂层，那么依然可能继续供给该含有六价铬的解决方案直至消耗完库存且无论如何不得迟于2006年7月1日然而在这种情况下，供应商有必要通知采购商，与新处方保持一致所需要的时间有资质的E&D实体必须授权与这些总则所存在的可能偏差表1（1）对于断裂荷载≥800e≤1000N/mm的材料，如果要求脱氢处理，那么应在图纸中有明确的DEIDRA的字样注明，例如：Fe/ZnNi DEIDRA（参看2.3.10）；对于断裂荷载≥1000N/mm2的材料，那么在图纸中可以省略注明，因为脱氢处理是必须的（2）对于特殊要求，在图纸中应注明不同的厚度值，例如：Fe/ZnNi 5表示最小厚度为5um。
广汽菲亚特审核条款
是否每个工位都易于得到清 晰的最新发布的作业指导 书？
用于控制的资源是否 充足？
匹配试验和Benestare （工厂批准）状态
过程控制与试验
检验实验设备管理
先进先出
问题解决
F-S
F
F
F-S-C
F
F
F
过程控制计划
D
日常与预防性的维护 （机器/模具/设备）
过程能力（短期、长期、设 备能力指数）
如果是多班次生产， 班次之间有交接班信 息传递吗？
操作工是否经过适当 的培训？
自我验证状态
来料控制
记录控制
可追溯性
经验教训
F-C
F-S
F
F
F-S
F
F
F
F
流程图
B
设备工装状态（质量， 产能与时间进度）
二级零件批准
管理层参与
综合测试状态
生产批准
与“报告特性”相关的记 录控制
标识二级供应商的改进活动FF-SF
F-S-C
F
F
F
潜在失效模式及后果 工装设备和模具的保存 分析 条件
RELEASE TO PROD. (DaP)
物料需求数： 供应数：
CURRENT PRODUCTION
物料需求数： 供应数：
供应商质量
1文件
2模具/ 设备
3过程
4人力资源与组织架构
5产品验证/ 一日生产
6质量运行
7质量运行
8物流
9持续改进
图纸和技术文件
A
模具状态（质量，产能 与时间进度）
二级供应商的批准
PCPA (过程审核）
GAC FIAT Automobiles Co., Ltd
广汽菲亚特包装标准
一目的 Purpose二适用范围・设定基础 Scope and foundation 适用范围 Scope 对于GF 供应物流容器适用（KD 部品参照) For all the GF logistics containers (Reference for KD parts)设定基础 Basis 结合GF 供应物流运输车辆,使用欧洲标准规格容器 Integrate with the GF logistics transportation vehicle with the use of European standard containers 三GF 包装标准化的总体要求 General rules（1）包装设定务必确保零件在装配之前无品质变化 To make sure the parts quality wouldn't change before installation.（4）包装设定应在确保运输成本最低化的同时，需要满足承重、强度、韧度的技术要求The packaging shall meet technical parameters for load-bearing, strength and tenacity while ensuring the lowest transportation cost.包装容器选择以一次成型塑料容器为优先，根据堆叠的高度和承载重量来设定其技术参数。
Generally, containers by one shot process shall be preferred. Technical specs shall be set according to height of stack and load-bearing.针对特殊形状、重物等零件，通用容器不能满足时，采用专用容器。
For special shape, heavy or other parts where the general containers do not apply, special containers shall be used.（５）高安全性包装设定Packaging for high safety standard选用可嵌入、尺寸配合良好的容器，避免在物流过程中发生容器倒塌、散包、装载断（破）裂等情况。
菲亚特标准07416
Page:Date:Change Date DescriptionE d i t i o n normazioneC o d eC h .-4T F O-0741605/28/2002RECYCLING MARKINGS FOR PLASTIC,COMPOSITE AND ELASTOMERCOMPONENTS1/11ANY PRINTED COPY IS TO BE DEEMED AS UNCHECKED; THEREFORE THE UPDATED COPY MUST BE CHECKED IN THE APPROPRIATE WEB SITEC O N F IDE N T I A LT H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B Y F I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R I G I N A L I T A L I A N E D I T I O NPURPOSE OF THE STANDARDThis Standard estabishes rules for marking plastic, composite and elastomer automotive components so that their constituent material/s can be identified in order to facilitate selection and collection for recycling purposes.Standard symbols used herein are taken from ISO 1043 - 1987 and ISO 11469: they comply with VDA Recommendation 260 for plastics and ISO 1629 - 1976 for elastomers.=June '922nd Edition - Fully revised.(MM)ANov.'92Marking requirements for percentage fabric reinforcement of rubber hoses revised. Reference to ISO standard for elastomers added together with standard symbols for materials.(MM)B Oct.'95Revised ISO symbol for thermosetting elastomer material from NSR to HNBR (Hydrogenated Nitril) and cancelled thermosetting elastomer material SBR Styrene Butadiene.(MM)=July '963rd Edition - Fully revised.(MM)=05/28/024th Edition - the following paragraphs have been revised: 3.1.1, 3.1.2 and their tables with a new one added (II Bis), 3.2.1 (T able III), 7.1 and 7.2.2. (MM)C O N F IDE N T I A L T H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B YF I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R IG I N A L I T A L I A N E D I T I O NC O N F IDE N T I A L T H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B YF I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R IG I N A L I T A L I A N E D I T I O N1.Base polymer symbolC O N F IDE N T I A L T H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B YF I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R IG I N A L I T A L I A N E D I T I O NC O N F IDE N T I A L T H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B YF I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R IG I N A L I T A L I A N E D I T I O NISO SYMBOLPSEC O N F IDE N T I A L T H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B YF I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R IG I N A L I T A L I A N E D I T I O NC O N F IDE N T I A L T H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B YF I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R IG I N A L I T A L I A N E D I T I O NC O N F IDE N T I A L T H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B YF I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R IG I N A L I T A L I A N E D I T I O NC O N F IDE N T I A L T H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B YF I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R IG I N A L I T A L I A N E D I T I O NC O N F IDE N T I A L T H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B YF I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R IG I N A L I T A L I A N E D I T I O NC O N F IDE N T I A L T H I S D O C U M E N T M U S T N O T B E R E P R O D U C E D O R C I R C U L A T E D T O T H E T H I R D P A R T I E S W I T H O U T P R I O R W R I T T E N C O N S E N T B YF I A T A U T O S .P .A . I N C A S E O F D I S P U T E T H E O N L Y V A L I D R E F E R E N C E I S T H E O R IG I N A L I T A L I A N E D I T I O N6.2Large components。
零部件试验认证流程与制度
零部件试验认证流程与制度 Homologation process and
regulations of parts
涉及过程 Reference process:零部件试验认证 使用部门 Validity area:: GF
修订 Modifications:
1.总则
程序 PROCEDURE
FGA，PC
样件清单提供
系统 sk effe
采购部，财务 部，供应链管 理部，产品技 术部
输入成本、物流费用 sk effe
产品技术部
状态确认
sk effe
FGA：MR
最终审核
sk effe
供应链管 理 部 采购部，整车 制造部
信息确认，制定订单
sk effe
样件订购
供应链管 理部
样件接收发送
主要内容
采购部，产品 技术部
流程 试验项目和样件清单
试验计划的制定
采购部，供应 链管理部
样件订购
供应商
样件生产、检查、提交
时间 PS 装车前 4 个月
PS 装车前 4 个月
活动
确认过程验证综合性 试验项目清单和样件 清单、数量。
产品技术部提供清单 及供货计划，采购部 与供应商确认供货时 间节点，确定后交 SCM 进行订购。
按照计划日程及相关
技术标准提交样件及
零件检查报告。 NG
质量部
产品技术部/ 车型试验科
样件接收和 纳入检查
OK
样件领取
产品技术部/ 车型试验科
试验开展
产品技术部/
车型试验科
NG
产品技术部/车 身科、底盘科 质量部 采购部 供应商
菲亚特标准50020
Type of material Cast irons Steels Non-ferrous materials Non-metal materials (Rubbers) Non-metal materials (Plastics) Non-metal mat. (Lubricants J, Coolants, Protective mat.) Paints, enamels, adhesives, chemical products and fuels Composites, seals and coatings
6
Special plastics, in case reinforced, in form of pressed, shaped, extruded and rolled products
6
7 8 9
7 8 9 Various materials
PUBLISHED BY SATIZ - NORMAZIONE
4 - Non-metal (rubbers) Fig. 0 1 2 3 4 5 6 7 8 9 6 - Non-metal materials (Lubricants, coolants, protective materials) Fig. 0 1 Class of materials Various materials Oils, greases and complementary products for vehicles Special rubbers, in case reinforced Unified sealing rubbers, in case reinforced Class of material Unified mechanical rubbers, in case rein forced
机动车检测机构技术规范
机动车检测机构技术规范2012-02-26关于发布在用机动车排放污染物检测机构技术规范的通知环发[2005]15号各省、自治区、直辖市环境保护局（厅）：为贯彻实施《中华人民共和国大气污染防治法》，规范对在用机动车排放污染检测机构的委托管理，现发布《在用机动车排放污染物检测机构技术规范》，请遵照执行。
附件：在有机动车排放污染物检测机构技术规范二○○五年一月三十一日主题词：环保机动车检测机构规范通知抄送：解放军环境保护局，新疆生产建设兵团环境保护局。
附件：在用机动车排放污染物检测机构技术规范前言为明确对在用机动车排放检测机构的委托要求，规范对在用机动车排放污染物检测机构的监督管理，依据《中华人民共和国大气污染防治法》等的有关规定，制定本规范。
本规范部分内容参考GB15481-2000《检测和校准实验室能力的通用要求》的内容制定。
本规范由国家环境保护总局提出。
本规范由国家环境保护总局解释。
本规范主要起草单位：国家环境保护总局机动车排污监控中心、清华大学、中国汽车技术研究中心在用机动车排放污染物检测机构技术规范1 范围本规范包含了在用机动车排放污染物检测机构的基本技术要求和体系管理要求，同时对检测机构的部分相关人员提出要求。
本规范适用于省、自治区、直辖市人民政府环境保护行政主管部门对在用机动车排放污染物检测机构的委托。
本规范所指的在用机动车排放污染物检测机构，是指承担对在用机动车排气污染年度（定期）检测的机构。
2 引用标准GB7258-2004《机动车运行安全技术条件》3 术语和定义3.1 在用机动车本规范中的在用机动车是指国家或地方机动车排放标准中规定的、上牌照以后的、需定期检测的机动车。
4 基本要求4.1 在用机动车排放污染物检测机构（以下简称“检测机构”）应是在中华人民共和国境内注册的独立法人单位。
检测机构应遵守国家或地方法律、法规，依法取得环境保护行政主管部门的委托才能开展在用机动车排放污染物定期检测工作。
9.55535_050304菲亚特DV规范
G2
10W60
-
Fiat 9.55535-H3
-
“Long drain” oils for X spark ignition and X 50,000 / 5W40 M2 Diesel engines with > 3.5 30,000 / 2 years 0W40 A3/B3; B4 2 years (2) extended change intervals
Standard oils for X spark ignition > 3.5 20,000 / 1 year engines High performance X “long drain” oils for > 3.5 30,000 / H2 spark ignition 1 year engines Highest X performance oils for > 3.5 20,000 / H3 spark ignition 1 year engines
5
Ch.
Code
CMD
FIAT-GM POWERTRAIN P.E. PWT TESTING
9.55535
Page 2 of 13 Date: 03/04/05
§ “A”: TEST EQUIPMENT Chemical laboratory current instrumentation. § “B”: REFERENCES ASTM D 445 ASTM D 664 ASTM D 874 ASTM D 2896 ASTM D 4739 CEC L-36-A-97 CEC L-40-A-93 CEC M-02-A-78 DIN 51.400 DIN 51.452 DIN 51.757 SAE J 300 9.01102 9.01102/01 9.01103 7-A6311 7-A2400 7-M3000 07988 50015 50020
955535菲亚特DV规范
: &&0& ' : &&0& 3' : &&0& 3' : 6HPLV\QWKHWLF &&0& 3'
2WKHU W\SHV ZLWK RWKHU YLVFRVLW\ JUDGHV PD\ EH FRQVLGHUHG IRU VSHFLILF VHUYLFH UHTXLUHPHQWV
38%/,6+(' %< 6$7,= 6S$ 1250$=,21(
&21),'(17,$/ 7+,6 '2&80(17 0867 127 %( 5(352'8&(' 25 &,5&8/$7(' 72 7+( 7+,5' 3$57,(6 :,7+287 35,25 :5,77(1 &216(17 %< ),$7 $872 63 $ ,1 &$6( 2) ',6387( 7+( 21/< 9$/,' 5()(5(1&( ,6 7+( 25,*,1$/ ,7$/,$1 (',7,21
_ q l&l $11(;(6
&21),'(17,$/ 7+,6 '2&80(17 0867 127 %( 5(352'8&(' 25 &,5&8/$7(' 72 7+( 7+,5' 3$57,(6 :,7+287 35,25 :5,77(1 &216(17 %< ),$7 $872 63 $ ,1 &$6( 2) ',6387( 7+( 21/< 9$/,' 5()(5(1&( ,6 7+( 25,*,1$/ ,7$/,$1 (',7,21
菲亚特标准9.55655
(DA)
07/16/02
Edition 13 - Annexes added: Annex 23 Flat composite panels" - PULER Type - Porous Annex 42 Preformed panels" - PULER Type - Porous (DA)
CONFIDENTIAL THIS DOCUMENT MUST NOT BE REPRODUCED OR CIRCULA TED TO THE THIRD PARTIES
| § ”B” : REFERENCES
|07416 |50496/01 |0.00013 |7.G2000
|7.G2090
|7.G2110 |7.R7400 |9.01102 |9.01102/01 |9.01103 |9.55260/01
|9.55441/18
| Recycling markings for plastic, composite and elastomer components. TFO | Water and repellant properties of occupant compartment trim fabrics. TMD | Date of maufacture marking. NPR | Determining the resistance to combustion of the non-metallic materials for parts
1
Type PULER - Porous
PUBLISHED BY SATIZ - NORMAZIONE
CONFIDENTIAL THIS DOCUMENT MUST NOT BE REPRODUCED OR CIRCULA TED TO THE THIRD PARTIES
车辆标准规范中英文对照汇总
车辆标准规范中英文对照车辆综合1 GB 1495-1979 机动车辆允许噪声Permissible noise limit emitted by power-driven vehicles2 GB/T 1496-1979 机动车辆噪声测量方法Measuring method for noise of power-driven vehicles3 GB/T 3730.1-1988 汽车和半挂车的术语和定义车辆类型Motor vehicle and semi-trailer-type-terms and definitions4 GB/T 3730.2-1996 道路车辆质量词汇和代码Road vehicle--Masses--Vocabulary and codes5 GB/T 3730.3-1992 汽车和挂车的术语及其定义车辆尺寸Motor vehicles and towed vehicles—Dimensions of vehicles—Terms and definitions6 GB 4094-1994 汽车操纵件、指示器及信号装置的标志Motor vehicles--Symbols for controls,indicators and tell-tales7 GB/T 4782-1984 道路车辆--操纵件、指示器及信号装置--词汇Road vehicles--Controls, indicators and tell-tales--Vocabulary8 GB/T 4970-1996 汽车平顺性随机输入行驶试验方法Method of random input running test--Automotive ride comfort9 GB/T 7031-1986 车辆振动输入路面平度表示方法Vehicle vibration--Describing method for road surface irregularity10 GB 8410-1994 汽车内饰材料的燃烧特性Flammability of automotive interior materials11 GB/T 9417-1988 汽车产品型号编号规则Motor vehicles-type and model designation12 GB/T 11551-1989 汽车乘员碰撞保护Motor vehicles—Occupant cash protection13 GB 11552-1989 汽车内部凸出物Motor vehicles—Internal protrusions14 GB 11553-1989 汽车正面碰撞时对燃油泄漏的规定Motor vehicles—Regulation of fuel leakage during frontal impact15 GB/T 11559-1989 汽车室内尺寸测量用三维H点装置Motor vehicles—Use in defining their seating accommodations—Three dimensional H point machine16 GB/T 11568-1989 汽车罩锁装置Motor vehicles—Hood latch system17 GB/T 12478-1990 客车防尘密封性试验方法Dust proof performance—Test method for buses18 GB/T 12480-1990 客车防雨密封性试验方法Rain proof performance test mothod for buses19 GB/T 12484-1990 客车车身术语Terms for the bus body20 GB/T 12534-1990 汽车道路试验方法通则Motor vehicles—General rules of road test method21 GB/T 12535-1990 汽车起动性能试验方法Motor vehicles—Starting performance—Test methods22 GB/T 12536-1990 汽车滑行试验方法Motor vehicles—Coastdown—Test method23 GB/T 12537-1990 汽车牵引性能试验方法Motor vehicles—Towing performance—Test method24 GB/T 12538-1990 汽车重心高度测定方法Motor vehicles—Height of gravity center—Measuring method25 GB/T 12539-1990 汽车爬陡坡试验方法Motor vehicles—Steep hill climbing—Test method26 GB/T 12540-1990 汽车最小转弯直径测定方法Motor vehicles—Minimum turning diameter—Method of measurment27 GB/T 12541-1990 汽车地形通过性试验方法Motor vehicles—Passing topography capacity—Test method28 GB/T 12542-1990 汽车发动机冷却系冷却能力道路试验方法Motor vehicles—Cooling capacity for engine cooling system—Test method on road29 GB/T 12543-1990 汽车加速性能试验方法Motor vehicles—Acceleration performance—Test method30 GB/T 12544-1990 汽车最高车速试验方法Motor vehicles—Maximum speed—Test method31 GB/T 12545-1990 汽车燃料消耗量试验方法Motor vehicles—Fuel consumption test method32 GB/T 12546-1990 汽车隔热通风试验方法Motor vehicles—Ventilation and heat insulation—Test method33 GB/T 12547-1990 汽车最低稳定车速试验方法Motor vehicles—Minimum stable speed—Test method34 GB/T 12549-1990 汽车操纵稳定性术语及其定义Automotive controllability and stability—Terms and definitions35 GB/T 12674-1990 汽车质量(重量)参数测定方法Motor vehicles—Weight parameter—Measuring method36 GB/T 12677-1990 汽车技术状况行驶检查方法Motor vehicles—Technical condition—Inspection method37 GB/T 12678-1990 汽车可靠性行驶试验方法Reliability running test method for automobiles38 GB/T 12679-1990 汽车耐久性行驶试验方法Motor vehicles—Durability running—Test method39 GB/T 13860-1992 地面车辆机械振动测量数据的表述方法Mechanical vibrations--Land vehicles-Method for reporting measured data40 GB/T 14168-1993 汽车制动液类别图形标志Motor vehicles--Graphical symbols to designate brake fluid types41 GB/T 14172-1993 汽车静侧翻稳定性台架试验方法Static roll stability test method for motor vehicles42 GB/T 15089-1994 机动车辆分类Motor vehicles--Classification43 GB 15740-1995 汽车防盗装置性能要求Motor vehicle--Protective devices against unauthorized use--Performance requirments44 GB/T 16735-1997 道路车辆车辆识别代号（VIN）位置与固定Road vehicles--Vehicle identification number(VIN)--Location and attachment45 GB/T 16736-1997 道路车辆车辆识别代号（VIN）内容与构成Road vehicles--Vehicle identification number(VIN)--Content and structure46 GB/T 16737-1997 道路车辆世界制造厂识别代号（WMI）Road vehicles--World manufacturer identifier(WMI)code47 GB/T 16738-1997 道路车辆世界零件制造厂识别代号（WPMI) Road vehicler--World parts manufacturer identifier(WPMI)code48 GB 7258-1997 机动车运行安全技术条件Safety specifications for motor vehicles operating on roads49 GB 13094-1997 客车结构安全要求The safety requirements for bus construction50 GB/T 16888-1997 客车安全顶窗The escape hatch of bus汽车发动机1 GB/T 5923-1986 汽车柴油机燃油滤清器的试验方法Test methods of fuel filters for automotive compression ignition engines2 GB/T 5924-1986 汽车柴油机燃油滤清器的试验值及分级Test values and classification of fuel filters for automotive compression ignition engines3 GB/T 12781-1991 汽车供油系气阻试验方法Motor vehicles—Vapor lock for fuel system—Test method4 GB/T 12782-1991 汽车采暖性能试验方法Motor vehicle—Heating performance—Test method5 GB/T 14169-1993 汽车空气滤清器接头A型和B型Air filter connections for motor vehicles--Types A and B6 GB/T 14170-1993 载货汽车空气滤清器滤芯尺寸规范Air filter elements for trucks--Dimensions7 GB/T 8409-1999 汽车发动机旋装式机油滤清器连接尺寸Road vehicles--Intermal combustion engines--Spin-on filters for lubrication oil--Dimension8 GB/T 17653-1999 汽车柴油机旋装式燃油滤清器安装和连接尺寸Road vehicles--Spin-on fuel filters for combustion-ignition engines--Mounting and dimensions9 GB/T 17692-1999 汽车用发动机净功率测试方法Measurement methods of net power for automotive engines汽车底盘与车身1 GB 1589-1989 汽车外廓尺寸限界Outside dimension limits of motor vehicles2 GB/T 2933-1995 充气轮胎用车轮和轮辋的术语、规格代号和标志Wheels/rims for pneumatic tyres--Nomenclature,designation and marking3 GB/T 3487-1996 汽车轮辋规格系列Rim contours for motor vehicles4 GB/T 4095-1995 载货汽车辐板式车轮在轮毂上的安装尺寸Disc wheels for trucks--Dimensional characteristics of attachment on hub5 GB/T 4784-1984 使用非石油基制动液的汽车液压制动软管总成Brake hose assemblies for hydraulic braking systems of motor vehicles used with a non-petroleum base hydrau-lic fluids6 GB/T 5334-1995 轿车钢制车轮性能要求和试验方法Performance requirements and test methods of passenger car steel wheels7 GB/T 5335-1985 汽车制动装置液压试验的连接器Automobile hydraulic pressure test connection for braking equipment8 GB/T 5345-1985 制动液容器的标记Labelling of containers for brake fluid9 GB/T 5620.1-1985 汽车和挂车制动名词术语及其定义制动系种类、组成、力学及现象The terms and definitions of braking of automotive vehicles and their trailers--Types,constituent elements,braking mechanics and phenomenon of braking system10 GB/T 5620.2-1985 汽车和挂车制动名词术语及其定义零部件The terms and definitions of braking of automotive vehicles and their trailers--The parts and components of braking equipment11 GB/T 5909-1995 载货汽车车轮性能要求和试验方法Performance requirements and test methods of truck wheels12 GB/T 5911-1986 转向盘尺寸Steering wheel--Dimensions13 GB/T 5921-1986 汽车和挂车气压制动系部件上接口的识别标记Motor vehicles and towed vehicles--Air braking systems--Identification of connections on units14 GB/T 5922-1986 汽车和挂车气压制动装置压力测试连接器Motor vehicles and towed vehicles--Pressure test connection for compressed-air pneumatic braking equipment15 GB/T 6792-1996 客车车身骨架应力、形变测量方法Measure method of stress and deformation for bus budy skeleton16 GB 7062-1986 汽车气制动软管总成Automotive air brake hose assemblies17 GB 7063-1994 汽车护轮板The wheel guards of motor vehicles18 GB/T 7680-1987 液力变矩器性能试验方法Hydrodynamic torque converter--Method of performance tests19 GB/T 10484-1989 汽车真空制动软管总成Vacuum brake hose assemblies for motor vehicle20 GB/T 11549-1989 汽车安全带总成性能要求和试验方法Motor vehicles—Safety belt assemblies—Performance requirements and test methods21 GB 11550-1995 汽车座椅头枕性能要求和试验方法Motor vehicles--Seats head vestraints--Performance requirements and test methods22 GB 11555-1994 汽车风窗玻璃除雾系统的性能要求及试验方法Motor vehicles--Windshield demisters--Performance requirements and test methods23 GB 11556-1994 汽车风窗玻璃除霜系统的性能要求及试验方法Motor vehicles--Windshield defrosters--Performance requirements and test methods24 GB/T 11558-1989 汽车安全带用卷收器性能要求和试验方法Motor vehicles—Retractors for safety belt—Performance requirements and test methods25 GB 11561-1989 汽车加速器控制系统的技术要求Motor vehicles—Accelerator control systems—Technical requirements26 GB 11562-1994 汽车驾驶员前方视野要求及测量方法Motor vehicles--Forward visibility for drivers--Requirements and measurement methods27 GB/T 11563-1995 汽车H点确定程序Motor vehicles--Procedure for H-point determination28 GB 11565-1989 轿车风窗玻璃刮水器刮刷面积Passenger cars—Windshield wipers—Wiped areas29 GB 11566-1995 轿车外部凸出物Passenger car--External protrusions30 GB 11567-1994 汽车和挂车侧面及后下部防护装置要求Motor vehicles and trailers--Lateral and underrun protections--Requirements31 GB/T 11611-1989 汽车液压制动系金属管、内外螺纹管接头和软管端部接头Motor vehicles—Hydraulic braking systems—Pipes tapped holes, male fittings and hose end fittings32 GB/T 12482-1990 客车侧窗平面玻璃规格系列Side window flat glasses systematization for buses33 GB/T 12483-1990 客车风窗、后窗玻璃规格系列Buses windscreen and rear window glass—Systematization34 GB/T 12673-1990 汽车主要尺寸测量方法Molor vehicles—Basic dimensions—Measuring method35 GB/T 12780-1991 货车、客车制动器台架试验方法Trucks and buses—Brake—Bench test methods36 GB/T 13051-1991 汽车机械式变速器动力输出孔连接尺寸Motor vehicles—Connections for PTO37 GB/T 13053-1991 客车驾驶区尺寸Bus driver compartment dimensions38 GB/T 13054-1991 客车驾驶区尺寸术语Bus driver compartment dimensions terms39 GB/T 13055-1991 客车乘客区尺寸Bus passenger compartment dimensions40 GB/T 13056-1991 客车乘客区尺寸术语Bus passenger compartment dimension terms41 GB/T 13057-1991 客车驾驶员座椅尺寸规格Bus driver seat—Dimensions42 GB/T 13058-1991 客车驾驶员座椅技术条件Bus drivers seat—Technical specification43 GB/T 13059-1991 客车乘客座椅尺寸规格Bus passenger seat—Dimensions44 GB/T 13060-1991 客车乘客座椅技术条件Bus passenger seat—Technical specifications45 GB/T 13061-1991 汽车悬架用空气弹簧橡胶气囊Air spring for automotive suspension—Rubber bellows46 GB 13594-1992 汽车防抱制动系统性能要求和试验方法Vehicles anti-lock braking systems performence requiremants and test procedures47 GB/T 13604-1992 汽车转向球接头尺寸Motor vehicles—Steering ball joints—Dimensions48 GB 14166-1993 汽车安全带性能要求和试验方法Motor vehicles--Safety belt assemblies--Performance requirements and test methods49 GB 14167-1993 汽车安全带安装固定点Motor vehicles--Safety belt anchorages50 GB/T 14171-1993 汽车气制动系管路螺纹孔和管接头外螺纹Motor vehicles--Pneumatic braking systems--Tapped holes and male fittings51 GB 15083-1994 汽车座椅系统强度要求及试验方法Motor vehicles--Seat systems--Strengthrequirements and test methods52 GB 15084-1994 汽车后视镜的性能和安装要求Motor vehicles--Rear view mirrors--Requirements of performance and installation53 GB 15085-1994 汽车风窗玻璃刮水器、洗涤器的性能要求及试验方法Motor vehicles--Windshield wipers and washer systems--Performance requirements and test methods54 GB 15086-1994 汽车门锁及门铰链的性能要求和试验方法Motor vehicles--Door locks and door hinges--Performance requirements and test methods55 GB/T 15087-1994 汽车牵引车与全挂车机械连接装置强度试验Motor vehicles--Drawbar couplings and eyes for hinged drawbars--Strength test56 GB/T 15088-1994 汽车半挂车牵引座牵引销强度试验Motor vehicles--Fifth wheel coupling pins--Strength test57 GB/T 15704-1995 轿车车轮冲击试验方法Passenger cars--Wheels--Impact test procedure58 GB/T 15705-1995 载货汽车驾驶员操作位置尺寸Trucks--Operating position demensions of driver59 GB 15741-1995 汽车和挂车号牌板(架)及其位置The license plates (crackets) and its position on motor vehicles and trailer60 GB 15743-1995 轿车侧门强度Passenger car--Strength of side doors61 GB 16897-1997 制动软管Brake hose62 GB/T 17346-1998 轿车脚踏板的侧向间距Passenger cars--Lateral spacing of foot controls63 GB 11557-1998 防止汽车转向机构对驾驶员伤害的规定The stipulation protecting drivers from being injured by motor vehicle steering mechanism64 GB/T 17351-1998 汽车车轮双轮中心距Dual spaeing of vechicle wheels65 GB 17354-1998 汽车前、后端保护装置Front and rear protective devices for passenger cars66 GB/T 17578-1998 客车上部结构强度的规定Provisions of strength for the Superstructure of bus67 GB 12676-1999 汽车制动系统结构、性能和试验方法Road vehicles-Braking systems-Structure performance and test methods68 GB 17675-1999 汽车转向系基本要求Steering system of motor vehicles-Basic requirements69 GB/T 17676-1999 天然气汽车和液化石油气汽车标志Natural gas vehicle and liquefied petroleum gas vehicle Identification marks车辆通用零部件1 GB/T 1359-1978 汽车与挂车气制动接头型式与尺寸Pneumatic brakes for motor vehicls and their trailers-couplings--Types and dimensions2 GB/T 7726.1-1998 铰接式客车机械连接装置术语Mechanical connections of articulated bus Glossary3 GB/T 7726.2-1998 铰接式客车机械连接装置技术要求Mechanical connections of articulated bus Technical requirements4 GB/T 7726.3-1998 铰接式客车机械连接装置球头销Mechanical connections of articulated bus Ball pin5 GB/T 7726.4-1998 铰接式客车机械连接装置球形衬套Mechanical connections of articulated bus Ball socket6 GB/T 7726.5-1998 铰接式客车机械连接装置伸缩篷Mechanical connections of articulated bus Telescopic tarpaulin车用电子、电气设备与仪表1 GB 4599-1994 汽车前照灯配光性能Photometric characteristics of headlamps for motor vehicles2 GB/T 4659-1984 汽车前照灯类型、主要尺寸和连接尺寸Type,main size and mounted dimension of headlamps for motor vehicle3 GB 4660-1994 汽车前雾灯配光性能Photometric characteristics of front fog lamps for motor vehicles4 GB/T 5053.1-1985 汽车与挂车之间24N 型电连接器Electrical connections between motor vehicles and towed vehicles--Type 24N5 GB/T 5053.2-1985 汽车与挂车之间12N 型电连接器Electrical connections between motor vehicles and towed vehicles--Type 12N6 GB/T 5053.3-1985 汽车与挂车之间电连接器的试验方法与要求Test methods and requirements of electrical connections between motor vehicles and towed vehicles7 GB/T 5054-1985 汽车与挂车的七芯电缆线Seven-core connecting cable of motor vehicles and towed vehicles8 GB/T 5337-1985 汽车电器、灯具和仪表名词术语Nomenclature and terminology for automotive electrical equipment, lighting and instrumentation9 GB 5920-1994 汽车前和后位(侧)灯、示廓灯和制动灯配光性能Photometric characteristics of front and rear position (side)lamps, end-outline marker lamps and stop lamps for motor vehicles and their trailers 10 GB/T 6784-1986 M10×1平座火花塞及其气缸盖安装孔Spark plug M10×1 with flat seating and cylinder head housing11 GB/T 6785-1986 M12×1.25 平座火花塞及其气缸盖安装孔Spark plug M12×1.25 with flat seating and cylinder head housing12 GB/T 6786-1986 M14×1.25 平座火花塞及其气缸盖安装孔Spark plug M14×1.25 with flat seating and cylinder head housing13 GB/T 6787-1986 M14×1.25 矮型平座火花塞及其气缸盖安装孔Compact spark plug M14×1.25 with flat seating and cylinder head housing14 GB/T 6788-1986 M14×1.25 矮型锥座火花塞及其气缸盖安装孔Compact spark plug M14×1.25 with conical seating and cylinder head housing15 GB/T 6789-1986 M14×1.25 锥座火花塞及其气缸盖安装孔Spark plug M14×1.25 with conical seating and cylinder head housing16 GB/T 6790-1986 M18×1.5 平座火花塞及其气缸盖安装孔Spark plug M18×1.5 with flat seating and cylinder head housing17 GB/T 6791-1986 M18×1.5 锥座火花塞及其气缸盖安装孔Spark plug M18×1.5 with conical seating and cylinder head housing18 GB/T 7360-1987 汽车与挂车照明和信号装置的工作电压及其测量Working voltages and their measurement for lights and lighting signal devices fitted to motor vehicles and towed vehicles19 GB/T 7825-1987 火花塞Spark plugs20 GB/T 10485-1989 汽车和挂车外部照明和信号装置基本环境试验Basic environmental testing of lighting and light signalling devices for motor vehicles and their trailers21 GB/T 12548-1990 汽车速度表、里程表检验校正方法Motor vehicles—Speedometer and odometer—Calibration method22 GB 15082-1994 汽车用车速表Motor vehicles--Speed meters23 GB 15235-1994 汽车倒车灯配光性能Photometric characteristics of reversing lamps for motor vehicles and their trailers24 GB 15742-1995 汽车电喇叭的性能要求及试验方法Automotive--Electric horn--Performance requirements and test methods25 GB/T 17348-1998 道路车辆会车光束倾斜角随载荷变化的测量Motor vehicle--Measurement of variations in dipped beam headlamp angle as a function of load26 GB/T 17349.1-1998 道路车辆汽车诊断系统词汇Road vehicles--Diagnostic systems for motor vehicles--Vocabulary27 GB/T 17349.2-1998 道路车辆汽车诊断系统图形符号Rord vehicle Diagnostic systym Graphical symbols28 GB 17509-1998 汽车和挂车转向信号灯配光性能Photometric characteristics of direction indicators for motor vehicles and their trailers29 GB 17510-1998 摩托车光信号装置配光性能Photometric characteristics of light-signalling devices for motorcycles30 GB 4785-1998 汽车及挂车外部照明和信号装置的安装规定Prescription for installation of the external lighting and light signalliug devices for motor vehicles and their trailers31 GB 11554-1998 汽车及挂车后雾灯配光性能Photometric characteristics of rear fog lamp for motor vehicles and their tralers32 GB 11564-1998 机动车回复反射器Retro refletor for motor vehicles33 GB 5948-1998 摩托车白炽丝光源前照灯配光性能Photometric characteristics of motocycle headlamps epuipped with filament light sources汽车1 GB/T 918.1-1989 道路车辆分类与代码机动车Classification and code for road vehicles—Motor vehicle2 GB/T 918.2-1989 道路车辆分类与代码非机动车Classification and code for road vehicles—Non-motor vehicle3 GB/T 1332-1991 载货汽车定型试验规程Trucks—Engineering approval evaluation program4 GB/T 1333-1977 汽车产品质量定期检查试验规程Test code for regular quality inspection of automobile products5 GB/T 4780-1984 载货汽车车身名词、术语Glossary of truck body6 GB/T 4971-1985 汽车平顺性名词术语和定义Terms and definitions--Automotive ride comfort7 GB/T 5902-1986 汽车平顺性脉冲输入行驶试验方法Method of pulse input running test--Automobile ridecomfort8 GB/T 6104-1985 机动工业车辆名词术语Powered industrial trucks--Terminology9 GB/T 6323.1-1994 汽车操纵稳定性试验方法蛇行试验Controllability and stability test procedure for automobiles--Pylon course slalom test10 GB/T 6323.2-1994 汽车操纵稳定性试验方法转向瞬态响应试验(转向盘转角阶跃输入) Eontrollability and stability test procedure for automobiles--Steering transient response test(Steering wheel angle step input)11 GB/T 6323.3-1994 汽车操纵稳定性试验方法转向瞬态响应试验(转向盘转角脉冲输入) Contorllability and stability test procedure for automobiles--Steering transient response test(Steering wheel angle pulse input)12 GB/T 6323.4-1994 汽车操纵稳定性试验方法转向回正性能试验Controllability and stability test procedure for automobiles--Returnability test13 GB/T 6323.5-1994 汽车操纵稳定性试验方法转向轻便性试验Controllability and stability test procedure for automobiles--Steering efforts test procedure14 GB/T 6323.6-1994 汽车操纵稳定性试验方法稳态回转试验Controllability and stability test procedurefor automobiles--Steady static circular test procedure15 GB/T 7361-1987 半挂牵引车的制动及电路连接位置Brake and electrical connection locations of semi-trailer towing vehicle16 GB/T 7362-1987 全挂牵引车和货车的制动及电路连接位置Brake and electrical connection locations of truck andtrailer-towing vehicle17 GB/T 11380-1989 客车车身涂层技术条件Technical requirement for bus body coating18 GB/T 11381-1989 客车顶部静载试验方法Method of static load test for bus top19 GB/T 11382-1989 客车前保险杠效能试验方法正面固定式障壁碰撞试验Effect test procedure of front bumper for bus--Head-on collision with fixed wall20 GB/T 11709-1989 客车产品质量定期检查试验规程The regulated inspecting test procedure for bus21 GB/T 12427-1990 客车产品系列型谱Series and spectrum of buses22 GB/T 12428-1990 客车装载质量计算方法Laden mass calculation of buses23 GB/T 12429-1990 客车车身二氧化碳气体保护焊焊接质量要求及检验方法The quality requirement and test method for the carbon-dioxide arc welding of coach-body24 GB/T 12430-1990 客车乘客扶手杆的固定件基本型式与规格尺寸Basic type and size of fixings for passenger hand-rails in buses25 GB/T 12431-1990 客车乘客扶手杆断面Sections of passengers hand-rails in buses26 GB/T 12432-1990 客车乘客门门泵技术条件Specification for passenger door cylinder of buses27 GB/T 12433-1990 客车乘客门门泵试验方法Testing method for passenger door cylinder of buses28 GB/T 12675-1990 微型货车出厂检验方法Test methods of inspection after production for mini-truck29 GB/T 13043-1991 客车定型试验规程Buses—Engineering approval evaluation program30 GB/T 13044-1991 轻型客车定型试验规程Light buses—Engineering approval evaluation program31 GB/T 13046-1991 轻型客车产品质量定期检查试验规程Testing regulations for light bus and light van periodical inspection32 GB/T 16887-1997 卧铺客车技术条件Specification for sleeper bus33 GB/T 5910-1998 轿车质量分布Passenger car Mass distribution34 GB/T 17347-1998 商用道路车辆尺寸代码Commercial road vehicles Dimensional codes专用汽车1 GB/T 9465.1-1988 高空作业车分类Aerial platform--Classification2 GB/T 9465.2-1988 高空作业车技术条件Aerial platform--Specification3 GB/T 9465.3-1988 高空作业车试验方法Test methods for aerial platform4 GB/T 12503-1995 电视机通用技术条件Generic specification for TV vans5 GB/T 17350-1998 专用汽车和专用半挂车术语和代号Terms and marks in special automobiles and semi-trailers拖拉机1 GB/T 1592-1986 农业拖拉机动力输出轴Power take-off for agricultural tractors2 GB/T 1593.1-1996 农业轮式拖拉机后置式三点悬挂装置第1部分: 1、2、3和4类Agricultural wheeled tractors--Rear-mounted three-point linkage--Part 1: Categories 1,2,3 and 43 GB/T 1593.2-1987 农用轮式拖拉机三点悬挂装置第二部分: 1N类Agricultural wheeled tractors--Three-point linkage--Part 2: CategorY 1 N4 GB/T 1593.3-1987 农业轮式拖拉机三点悬挂装置第三部分: 0 类Agricultural wheeled tractors--Three-point linkage--Part 3: Categories 05 GB 1593.4-1987 农用轮式拖拉机三点悬挂装置第四部分:0类Agricultural wheeled tractors--Three-point linkage--Part 4: Category 06 GB/T 2777-1992 农业拖拉机动力输出轴安全防护罩型式尺寸和强度要求Power take-off safety shield for agricultural tractors--Types, dimensions and strength specifications7 GB/T 2778-1992 农业拖拉机动力输出皮带轮圆周速度和宽度Power take-off pulley for agricultural tractors--Peripheral speed and width8 GB/T 2779-1992 拖拉机拖挂装置型式尺寸和安装要求Tractor's connective equipment for trailers--Types, dimensions and mounting requirements9 GB/T 2780-1992 农业拖拉机牵引装置型式尺寸和安装要求Darwbars for agricultural tractors--Types dimensions and mounting requirements10 GB/T 3373-1982 拖拉机和农业、林业机械用轮辋Rims for tractors,agricultural and forestry machines11 GB/T 3871.1-1993 农业轮式和履带拖拉机试验方法第1 部分通用要求Test methods for agricultural wheeled and tracklaying tractors--Part 1: General requirements12 GB/T 3871.2-1993 农业轮式和履带拖拉机试验方法第2 部分整机参数测定Test methods for agricultural wheeled and tracklaying tractors--Part 2: Measurements of tractor parameters13 GB/T 3871.3-1993 农业轮式和履带拖拉机试验方法第3 部分动力输出轴功率试验Test methods for agricultural wheeled and tracklaying tractors--Part 3: PTO power tests14 GB/T 3871.4-1993 农业轮式和履带拖拉机试验方法第4 部分液压提升能力和输出功率试验Test methods for agricultural wheeled and tracklaying tractors--Part 4: Hydraulic lifting capacity and power tests15 GB/T 3871.5-1993 农业轮式和履带拖拉机试验方法第5 部分转向和离合器操纵试验Test methods for agricultural wheeled and tracklaying tractors--Part 5: Turning and clutch operating tests16 GB/T 3871.6-1993 农业轮式和履带拖拉机试验方法第6 部分制动试验Test methods for agricultural wheeled and tracklaying tractors--Part 6: Braking tests17 GB/T 3871.7-1993 农业轮式和履带拖拉机试验方法第7 部分视野测定Test methods for agricultural wheeled and tracklaying tractors--Part 7: Measurements of operator's field vision18 GB/T 3871.8-1993 农业轮式和履带拖拉机试验方法第8 部分噪声测量Test methods for agricultural wheeled and tracklaying tractors--Part 8: Measurements of noise19 GB/T 3871.9-1993 农业轮式和履带拖拉机试验方法第9 部分牵引功率试验Test methods for agricultural wheeled and tracklaying tractors--Part 9: Drawbar power tests20 GB/T 3871.10-1993 农业轮式和履带拖拉机试验方法第10部分低温起动试验Test methods for agricultural wheeled and tracklaying tractors--Part 10: Low temperature starting tests21 GB/T 3871.11-1993 农业轮式和履带拖拉机试验方法第11部分高温适应性试验Test methods for agricultural wheeled and tracklaying tractors--Part 11: Suitability tests for hot atmosphere22 GB/T 3871.12-1993 农业轮式和履带拖拉机试验方法第12部分使用试验Test methods for agricultural wheeled and tracklaying tractors--Part 12: Working tests23 GB/T 4329-1984 农业拖拉机三点悬挂装置锁销尺寸Three-point-linkage for agricultural tractors--Dimensions of linch pins24 GB/T 6229-1995 手扶拖拉机试验方法Methods of test for walking tractor25 GB/T 6236-1986 农业拖拉机驾驶座标志点Agricultural tractors--Operator's seat index point26 GB/T 6238-1986 农业拖拉机驾驶室的门道、紧急出口与驾驶员的工作位置尺寸Agricultural tractors--Access, exit and the operator's workplace--Dimensions27 GB 6376-1995 拖拉机噪声限值Noise limitation for tractors28 GB/T 6960.1-1995 拖拉机术语整机Tractor terminology--Complete tractor29 GB/T 6960.2-1995 拖拉机术语传动系Tractor terminology--Transmission system30 GB/T 6960.3-1995 拖拉机术语制动系Tractor terminology--Braking system31 GB/T 6960.4-1995 拖拉机术语行走系Tractor terminology--Running gears and undercarriages32 GB/T 6960.5-1995 拖拉机术语转向系Tractor terminology--Steering system33 GB/T 6960.6-1995 拖拉机术语液压悬挂系及牵引、拖挂装置Tractor terminology--Hydraulic hitch system and drawbar, hook34 GB/T 6960.7-1995 拖拉机术语驾驶室、驾驶座和覆盖件Tractor terminology--Cab, seat and sheet metal35 GB/T 6960.8-1986 拖拉机名词术语第八部分履带行走系统Tractor terminology--Part 8: Endless track installation for track laying tractor36 GB/T 6961-1986 拖拉机动力输出轴和牵引装置的使用要求Operating requirements for tractor power take-off and drawbars37 GB/T 6972-1986 农业轮式拖拉机驾驶座振动的测量Agricultural wheeled tractors--Operator's seat--Measurement of trahsmitted vibration38 GB/T 7120-1986 农用轮式拖拉机三点悬挂农具快速挂接器3N类Three-Point hitch implement quick-attaching coupler of agricultural wheeled tractors--Category 3N39 GB 7121-1986 农林轮式拖拉机防护装置强度试验方法和验收条件Agricultural and forestry wheeled tractors--Protective structures--Test method in the strength and acceptance conditions40 GB/T 7927-1987 手扶拖拉机振动测量方法Method of measurement for walking tractor vibration41 GB/T 8421-1987 农业轮式拖拉机驾驶座传递振动的评价指标Agricultural wheeled tractors--Operator seat--Evaluation criteria of transmitted vibration42 GB/T 10176-1988 手扶拖拉机牵引装置和动力输出皮带轮Walking tractors--Drawbar and pulley of power take off43 GB/T 10910-1989 农业轮式拖拉机驾驶员全身振动的测量Agricultural wheeled tractors—Measurement of whole-body vibration of the operator44 GB/T 10911-1989 农业轮式拖拉机和后悬挂农具的匹配Matching of agricultural wheeled tractors and rear mounted implements45 GB/T 10916-1989 农业轮式拖拉机前悬挂装置第一部分: 1、2类Agricultural wheeled tractors—Front-mounted linkage —Part 1: Category 1, 246 GB/T 10917-1989 农用轮式拖拉机前置动力输出轴Front-mounted power take-off for agricultural wheeled tractors47 GB/T 13875-1992 手扶拖拉机通用技术条件The general specification for walking tractors48 GB/T 13876-1992 农业轮式拖拉机驾驶员全身振动的评价指标Agricultural wheeled tractors--Evaluation criteria of whole body vibration of the operator49 GB/T 13877-1992 农业拖拉机和自走式机具密封驾驶室加压系统试验方法Agricultural tractors and self-propelled machines--Test method for enclosure pressurization systems50 GB/T 13878-1992 农业拖拉机和自走式机具封闭驾驶室采暖和通风系统性能试验方法Agricultural tractors and self-propelled machines--Performance of heating and ventilation systems in closed cabs--Method of test51 GB/T 14226-1993 草坪和园艺拖拉机三点悬挂装置Lawn and garden tractors--Three-point hitch52 GB/T 14785-1993 拖拉机和农林机械车轮侧向负载疲劳试验方法Wheels side load fatigue test methods for tractors, agricultural and forestry machines53 GB/T 14786-1993 拖拉机和农林机械车轮扭转疲劳试验方法Wheels torsion fatigue test methods for tractors, agricultural and forestry machines54 GB 15369-1994 农林拖拉机和机械安全技术要求第三部分: 拖拉机Tractors and machinery for agriculture and forestry--Technical means for ensuring safety--Part 3: Tractors55 GB/T 15370-1994 农业轮式和履带拖拉机通用技术条件General Specifications for agricultural wheeled and tracking tractors56 GB/T 15832-1995 林业轮式和履带拖拉机通用技术条件General specifications for forestry wheeled and tracklaying tractors57 GB/T 15833-1995 林业轮式和履带拖拉机试验方法Test methods for forestry wheeled and tracklaying tractors58 GB/T 6235-1997 农业拖拉机驾驶座及主要操纵装置位置尺寸Agricultural tractors--Operator's seating accommodation--Dimensions59 GB/T 16877-1997 拖拉机禁用与报废Prohibition and scrapping for tractors60 GB/T 17122-1997 草坪和园艺乘座式拖拉机动力输出套管Lawn and garden ride-on (riding) tractors--Power take-off61 GB/T 17123-1997 草坪和园艺乘座式拖拉机单点套管式悬挂装置Lawn and garden ride-on (riding) tractors--One-point tubular sleeve hitch62 GB/T 17124-1997 草坪和园艺乘座式拖拉机牵引杆Lawn and garden ride-on (riding) tractors--Drawbar63 GB/T 6232-1998 农林拖拉机和机械车轮在轮毂上安装尺寸Tractors and machinery for agriculture and forestry-Wheel-to-hub fixing dimensions挂车1 GB/T 4330-1984 农业挂车Agricultural trailer2 GB/T 4331-1984 农用挂车试验方法Test methods for agricultural trailers3 GB/T 4606-1984 道路车辆半挂车鞍座50号牵引销主要尺寸和安装、互换性尺寸Road vehicles--50 semi-trailer fifth wheel coupling pin--Basic and mounting/interchangeability dimensions4 GB/T 4607-1984 道路车辆半挂车鞍座90号牵引销主要尺寸和安装、互换性尺寸Road vehicles--90 semi-trailer fifth wheel coupling pin--Basic and mounting/interchangeability dimensions5 GB/T 4781-1984 牵引车与全挂车的机械连接装置互换性Mechanical connection between towing vehicle and full trailers for interchangeability6 GB/T 6420-1986 货运挂车系列型谱Freight trailer series pedigree7 GB/T 13872-1992 货运挂车定型试验规程Trailer--Rules for the identification test8 GB/T 13873-1992 货运挂车试验方法Trailer--Test procedure9 GB/T 13874-1992 货运挂车质量定期检查试验规程Trailer--Rules for the periodic quality inspection test10 GB/T 13880-1992 半挂牵引车牵引座的安装Road vehicles--Semi trailer fifth wheel mounting11 GB/T 13881-1992 牵引车与挂车之间气制动管连接器Pneumatic braking connections between motor vehicles and towed vehicles12 GB/T 13202-1997 摩托车轮辋系列Series of motorcycle rims13 GB/T 17275-1998 货运全挂车通用技术条件Technical requirements for freight full trailers摩托车。
菲亚特标准50440
This Standard consists of 2 pages.
Change
Date
Description
--- --A
May, 1991 05/18/05
Edition 3 --- Revised and re---edited. § 2 changed . (FD)
(OR)
ANY PRINTED COPY IS TO BE DEEMED AS UNCHECKED; THEREFORE THE UPDATED COPY MUST BE CHECKED IN THE APPROPRIATE WEB SITE
CONFIDENTIAL THIS DOCUMENT MUST NOT BE REPRODUCED OR CIRCULATED TO THE THIRD PARTIES WITHOUT PRIOR WRITTEN CONSENT BY FIAT AUTO S.P.A.
As regards the waterproof fabrics, and K specified in the relevant procurement Specification, the loss of mass is to be determined after a 2 --- h immersion of a test specimen in water at room temperature and subsequent drying in still air at room temperature. 3 EXPRESSION OF RESULTS The mass is determined as follows: P= P = Mass in g/m2 . P1 ⋅ 100 3 where :
广汽菲亚特对于CAMDS填报的要求
1中国汽车材料数据系统CAMDS培训目的本次课程培训的目的1.了解汽车行业的相关法规进展；2.阐明CAMDS数据的重要性；3.详细了解广汽菲克CAMDS数据上传的相关要求；4.促进双方在CAMDS数据收集过程中的有效沟通；3/434/43目录Contents国内外回收利用法规解读CAMDS系统简介广汽菲克CAMDS填报相关要求数据上传的常见问题及解决方案5/43国内外回收利用法规解读CAMDS系统简介广汽菲克CAMDS填报相关要求数据上传的常见问题及解决方案一、国内外回收利用法规解读国内外回收利用法规建立的背景欧盟回收利用法规相关指令最新进展中国回收利用法规标准最新进展6/431.1 法规建立的背景7/43汽车产品限制使用有害物质，提高回收利用水平是汽车可持续发展的必然趋势。
1.1 法规建立的背景8/431.2 欧盟的ELV法规2000年9月18日，欧盟发布2000/53/EC《关于报废汽车的指令》（E nd-of-L ife V ehicle，简称“ELV”)核心：设计、生产阶段限制使用有害物质，提高可回收利用率和可再利用率范围：M1类车型，N1类车型9/431.2 欧盟的RRR指令10/43RRR指令：2005年10月26日，欧盟发布2005/64/EC《关于型式认证中车辆可再使用性、可再利用性和可回收利用性的指令》管理模式：将对汽车回收利用和禁用物质的要求纳入新车型式认证中，强制性准入管理型式认证时间表：RRR指令补充修订：《2009/1/EC指令》增加了全产业链收集供应商材料数据信息的相关规定1.3 欧盟的REACH法规REACH法规全称：“Registration，Evaluation，Authorization and Restriction of Chemicals”《化学品注册、评估、授权和限制》REACH法规管理机构：欧洲化学品管理局(ECHA)SVHC清单：高关注度物质清单；发布机构：ECHA；发布时间：2008年10月28日，ECHA发布第一批高关注度物质，截至2015年12月17日，共发布14批168项，并且清单会不断更新；目前CAMDS系统已经录入所有高关注度物质，并根据SVHC清单的变更进行实时更新。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
'DWH 1DPH RI (QJLQHHU
9LRODWLRQ
<(6 > @
12 > @
6LJQDWXUH
67' * &20321(17 7<3( 6833/,(5
0DQXIDFWXULQJ OHYHO $ > @ % > @ & > @ ' > @ ( > @
6DPSOH 1R /HQJWK PP :LGWK PP 6DPSOH 1R /HQJWK PP :LGWK PP 6DPSOH 1R /HQJWK PP :LGWK PP 6DPSOH 1R /HQJWK PP :LGWK PP
> @
7(;7,/( /$%25$725<
>
@
(/$6720( /$%25$725<
>
@
5HTXHVWLQJ 'HSDUWPHQW '(6&5,37,21 2) 2%-(&7
&RQWDFW
7HO
AS UPDATE STATUS OF PRINTOUTS CANNOT BE MONITORED, CHECK THE WEB SITE FOR THE LATEST EDITION OF DOCUMENT
PUBLISHED BY SATIZ - NORMAZIONE
Edition
2
Ch.
--
Code
PGE
67' * &20321(17 7<3( 6833/,(5
0DQXIDFWXULQJ OHYHO $ > @ % > @ & > @ ' > @ ( > @
3DJH 'ZJ /DVW FKDQJH
&5,7(5,$ *29(51,1* 7+( 86( 2) 7+( 67$1'$5'
9HKLFOH W\SH &RPSRQHQW 'UDZLQJ 0DWHULDO 7DEOH 6LPSOH > @ ,VRWURSLF > @ 6XSSOLHU &RPSRVLWH > @ $QLVRWURSLF > @ <HV > @ <HV > @ :LGWK PP 7KLFN PP 7KLFN PP 7KLFN PP 7KLFN PP 7KLFN PP 7KLFN PP 7KLFN PP >+@ >+@ 1R > @ 1R > @ 1XPEHU RI OD\HUV 1XPEHU RI OD\HUV 1XPEHU RI OD\HUV 1XPEHU RI OD\HUV 1XPEHU RI OD\HUV 1XPEHU RI OD\HUV 1XPEHU RI OD\HUV
Change
Date
-
Mar. 96 04/27/04
Edition 1 –
nd
New; drawn up in accordance with the Technical Memory Procedures. Supersedes Standard 50433. (AN)
2 Edition – Manager (was Ajmar) changed. Deleted paragraph "Test time requirements". (AN)
5HTXHVW IRU VHOI H[WLQJXLVKLQJ FDSDELOLW\ &RQGLWLRQLQJ RI VDPSOHV 6DPSOH 1R /HQJWK PP
6DPSOH 1R /HQJWK PP :LGWK PP 6DPSOH 1R /HQJWK PP :LGWK PP
3DJH 'ZJ /DVW FKDQJH
6,*1,),&$1&( 2) 7(67 &20321(176
:(,*+ 2) &20321(176 $1' 7+(,5 &+$5$&7(5,67,&6 )25 $1 (9$/8$7,21 2) 7+( 6,*1,), &$1&( 2) 7+( 7(67 &20 321(17 7<3( 6,*1,), &$1&( 9$/8( $ &20321(17 ,1)/8(1&,1* 6,*1,) 2) 7(67 0,1 0$18) /(9(/
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
127( 7KH FKURQRPHWHU PXVW SHUPLW D SUHFLVLRQ RI PHDVXUHPHQW RI VHFV
'DWH 1DPH RI (QJLQHHU
9LRODWLRQ 6LJQDWXUH
<(6 > @
12 > @
67' * &20321(17 7<3( 6833/,(5
67$1'$5'6 0(17,21(' ,1 7+( 7(;7
)0966 81, ,62 * )HGHUDO 0RWRU 9HKLFOH 6DIHW\ 6WDQGDUG 5RDG YHKLFOHV WUDFWRUV DJULFXOWXUDO DQG IRUHVWU\ PDFKLQHU\ 'HWHUPLQLQJ WKH EHKDYLRXU GXULQJ FRPEXVWLRQ RI PDWHULDOV LQVLGH WKH YHKLFOHV $FFHOHUDWHG DJHLQJ LQ VXQOLJKW &DOFXODWLQJ WKH VLJQLILFDQFH RI WKH WHVW REMHFWV &RQVWUXFWLRQ IHDWXUHV RI H[SHULPHQWDO FRPSRQHQWV $ % & OHYHO
CONFIDENTIAL THIS DOCUMENT MUST NOT BE REPRODUCED OR CIRCULATED TO THIRD PARTIES WITHOUT PRIOR WRITTEN CONSENT BY FIAT AUTO S.P.A. IN CASE OF DISPUTE THE ONLY VALID REFERENCE IS THE ORIGINAL ITALIAN EDITION.
normazione
DETERMINING THE RESISTANCE TO COMBUSTION OF THE NON-METALLIC MATERIALS FOR PARTS INSIDE VEHICLE PASSENGER COMPARTMENT
PERFORMANCE STANDARD
7-G2000
Pagina: Data:
1 di 17
04/27/2004
SUPERVISOR: MANAGER:
BRUNACCI GIUSEPPE MAURIZIO CRISTINA
P&PE - EMM P&PE - EMM
011 0033874 011 0030925
PURPOSE This standard defines the apparatus to be used and the test methods to be followed to determine the resistance to combustion of the non-metallic materials used inside the passenger compartment which must conform to Federal Standard 302 and International Standard ISO 3795.