摩力克EM-30L(英文)
KROHNE电磁流量计产品简介说明书
©KROHNE 03/20027.02425.21.00GRElectromagneticFlowmetersVariable area flowmetersVortex flowmetersFlow controllersElectromagnetic flowmetersUltrasonic flowmetersMass flowmetersLevel measuring instrumentsCommunications technologyEngineering systems & solutionsSwitches,counters,displays and recordersHeat meteringPressure and temperatureApplicationKROHNE electromagnetic flowmeters are to be found in many industrial sectors and applications.Just a small selection:G Chemical industry G Water and wastewaterGHydraulic transport,liquid products with up to 50% solids content G Paper and woodpulp production G Pharmaceutical G Food and beveragesG Filling and dispensing processes G Highly abrasive slurriesG High-pressure industrial processes GPartially filled pipelinesand many,many other applications in other industriesFIT and FORGET !All electromagnetic flowmeters are delivered ready for operation.Install the flowmeter in the pipeline,make the electrical connection,that's it.Always one step ahead with KROHNEThis highly accurate measurement technology is available with integrally or remote mounted converter,some with measuring errors of less than 0.2% of the measured value.The primary head is installed in the pipeline,while the signal converter for signal processing is remote mounted in a field housing or 19" plug-in unit.In the integral system,the signal converter is mounted in a housing with high protection category directly on the primary head.With meter sizes of DN2.5 - 3000 / 1/10" - 120",measurements can be carried out from 2l/h to 300 000m3/hand more.Most of the devices are approved for use in hazardous locations.Various materials are available for the measuring tube,liner and electrodes of the flowmeters for most applications. Electromagnetic flowmetersProduction and calibrationAll electromagnetic flowmeters from KROHNE meet the requirements of CE directives and EMC guidelines.Fabrication and production shops are certified to ISO 9001.At KROHNE,all electromagnetic flowmeters are calibrated by direct comparison of volumes,the most accurate calibration method of all.The KROHNE calibration rigs are the world's biggest and most accurate,and are accredited to EN17 025.Measurement uncertainty is less than 0.013% of themeasured value for meter sizes up to DN 3000 / 120" and above.7Electromagnetic flowmeters >0.05 µS /c m >5 µS /c m >20 µS /c m >50 µS /c mD N 2.5,4,6 1/10”,1/6”,1/4”D N 10 3/8”D N 32 11/2”Signal converterDatenblätterF l a n g e c o n n e c t i o n s F l a n g e l e s s ‘s a n d w i c h ’d e s i g n C h e m i c a l s W a t e r a n d s e w a g e P a r t i a l l y f i l l e d p i p e s P h a r m a c e u t i c a l s ,s a n i t a r y B a t c h i n g (1-10s )V e r y a b r a s i v e s l u r r i e s H i g h p r e s s u r e 2- o r 2 x 2-w i r e s y s t e mG e n e r a l p u r p o s e S a n i t a r y c o n n e c t i o n s H A R T ®/R S 485 (s t a n d a r d )P r o f i b u s P A H A R T ®/R S 485 (o p t i o n )H A R T ® (o p t i o n )O t h e r s o n r e q u e s t m Ao u t p u t ,2 w i r e c o n n e c t i o n ≤3 W ≤5 V A / ≤4.5 W ≤10 V A / ≤8 W ≤15 V A / ≤15 W ≤50 V A 2o r 2 x 2-w i r e s y s t e m 24,48,100 – 240 V A C ,48– 63 H z 24 V D C 24 V A C / D C 100 – 230 V A C ,48 –63 H z L i q u i d s ,p a s t e s S l u d g e a n d s l u r r i e s % s o l i d s /v o l u m e ≤3%S l u d g e a n d s l u r r i e s % s o l i d s /v o l u m e ≤5%S l u d g e a n d s l u r r i e s % s o l i d s /v o l u m e ≤30%P u l s a t i n g f l o w ,< 200 p u l s e s /m i n B a t c h i n g p r o c e s s > 1.5 s P a p e r a n d p u l p H y d r a u l i c t r a n s p o r t (o r e d r e s s i n g )o n l y I F C 090 K -C A P C a p a c i t i v e s i g n a l p i c k u p F ou n d a t i o n F i e l d B u s F A D N 251”D N 40 11/2”D N 502”D N 803”D N 1004”D N 1255”D N 1506”D N 2008”D N 25010”D N 30012”≤D N 1800≤72”≤D N 3000≤120”I S O f i t t i n g l e n g t h o n l y I F C 110 P F a n d I F C 210 E -P F P a r t i a l l y f i l l e d p i p e s ,AQUAFLUXECOFLUX 1000ALTOFLUX 2000ALTOFLUX 4000PROFIFLUX 5000VARIFLUX 6000ALTOFLUX 2W 2 wireBATCHFLUXCAPAFLUXTIDALFLUX partially filledALTOFLUX IFS 2005 FALTOFLUX IFS 4005 FALTOFLUX M 900IFC 010 K,FIFC 020 K,F ,EIFC 040 K 2 wireIFC 090 K,F IFC 090 K-CAP IFC 110 F IFC 110 PFIFC 210 E IFC 210 E-PFSC 150 FBatchflux IFC 012 KElectrical conductivitySizesConnectionsApplications (examples)Flow measurements (examples)Power supply Power consuptionInterfacesIFM 1080 KG Flangeless versionG Rugged measuring tube withstainless steel reinforced 080 KG Flanged connectionsG Steel housingµP-signal converter in plasticsIFM 4080 KG Flanged connectionsG Steel housingTeflon® PFA liner,reinforced withIFM 5080 KG Flangeless versionG Stainless steel housing The only precision flowmeter IFM 6080 KG Various sanitary/flangedconnectionsStainless steel housingG Precision flowmeterG With capacitive signal pickup(electrodes not in contact withG Flangeless versionG Rugged measuring tube withstainless steel reinforced G Flanged connectionsG Steel housingG Liner of Polypropylene,NSF-G Flanged connectionsG Steel housingG Teflon® PFA liner,reinforced withG Flangeless (sandwich) designG Stainless steel housingG The only precision flowmeter with G Flanged connectionsG Steel housingG Measuring tube made of Al2O3G Various sanitary/flanged connec-tions,stainless steel housingG FDA approved Teflon® PFA liner,G Designed for partially filled pipelinesG Excellent measuring accuracy,for low levels,through the integratedG IFC 010 K/IFC 020 K of integral design G IFC 010 F/IFC 020 F in field housing G IFC 020 E 19”plug-in version.G IFC 090 K of integral designG IFC 090 F in field housingG Signal processing by microprocessor,G Signal converter in field housingG Signal processing by microprocessor,outstanding interference rejection,G Signal converter in field housing for wall mounting G Signal processing by microprocessor,outstanding interference rejection,T o w e r h e i g h t 43 m e q u i v a l e n t t o 141 f t / n e t v o l u m e 350000 l i t r e s e q u i v a l e n t t o 95000 U S G a lPrecisionLM28 precision level switches control the flow volume and various computer-aided volume totalizersQmInlet run ≥10 ×DN (DN = meter size)©G The world’s largest and most accurate calibration rigGCalibration of flowmeters up to DN 3000 / 120”GCalibration by direct comparison of volumes,altogether the most accurate method GComparison measurements with so-called master meters are much less accurate and cannot be verifiedGThe volume measurement standards ofKROHNE calibration rigs have been calibrated by NMI,the Netherlands Standards Institute.Measurement uncertainty is less than 0.013% of the measured value.GKROHNE Altometer calibration rigs are accredited in conformity with EN 17 025.GCalibration accuracy is better than 99.97% of the measured value.GThe error of measurement of the calibration rigs is better by a factor of 10 than theaccuracy data of the flowmeter being tested.GAll flowmeters are calibrated underreference conditions,similar to EN 29 104.GAll calibration data are genuine and verifiable; documented in writing in the calibration reports,which are supplied together with each KROHNE flowmeter.An example is shown on the right.E r r o r o f m e a s u r e m e n t [% o f m e a s u r e d v a l u e ]Flow rate [m 3/h]0,50,402000400060008000100000,30,20,10,0-0,1-0,2-0,3-0,4-0,5+ 0.03%Accuracy inspires confidenceAt this flowrate,a typical public swimming-pool can be filled in less than 1 minute.Inaccuracy is less than 0.013% in terms of volume and less than 0.26 mm in terms of filling level (equal to the thickness of a single hair),based on an average pool depth of 2 metres.Flowmeters up to DN 3000/120”creates theKROHNE standardOutlet run ≥2 ×DN (DN =meter size)Volume flow rate Q max = 40 000 m 3/h= 11 m 3/sMeasuring Principle 3.1The induced voltage signal is picked up either by two measuring elec-trodes in conductive contact with the medium or indirectly bycapacitive coupling.A signal converter amplifies the signal and convertsit into a standard analog signal (e.g.4 to 20 mA) and a frequencysignal (e.g.1 pulse for every US gallon or cubic metre of mediumflowing through the measuring tube).To ensure that the voltage is not short-circuited by the pipe wall,themeasuring tube is made of an electrically insulating material or fittedwith an insulating liner.Measurement is largely independent of the flow profile and other prop-erties of the medium,such as pressure,temperature,viscosity,density,consistency,electrical conductivity,and electrode contamination.Measuring systemsThe electromagnetic flowmeter consists of a primary head,that isinstalled in the pipeline,and a signal converter.The compact design has the signal converter mounted directly on theprimary head.For systems with pulsed d.c.field the primary head field coils whichgenerate the magnetic field are energized by a pulsed direct currentfrom the signal converter.The measuring signal is a squarewave voltage of the same frequency.These systems feature extremely small measuring errors. Electromagnetic flowmeters measure the volume flow of electricallyconductive liquids and slurries.Measuring principleAn electric conductor,in this case the electrically conductive medium,passes through a magnetic field.The voltage U induced in this mediumis directly proportional to the mean flow velocity v.Magnetic inductionB (magnetic field strength) and the distance between electrodes D(nominal pipe diameter) are constant.K instrument constantB magnetic field strengthv mean flow velocityD electrode spacingThe volumetric flow rate qv can be calculated according toTherefore:q v=U x D xπ(4)K x B4The reducing angle (α) should not exceed 8°(equivalent to α/2 = 4°),otherwise measuring accuracy may be affected.If the reducing angle is greater,a straight inlet section must be fitted between reducing socket and primary head.Expanding sectionPressure Loss CalculationFor the expanding section,the optimum angle of expansion is α= 8°.ζat α= 8°d1/d2 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0ζ10.0180.0230.02550.0280.030.03080.03150.03230.0332Recommendations for installationSelection of meter sizeThe size of primary head should if possible be selected to provide a velocity of 2 to 3m/s or 6 to 9ft/sec.for the full-scale range. Minimum full-scale range is 0.5m/s or 1.5ft/sec.,maximum is 10 or 11m/s or 30 or 33ft/sec.,depending on flowmeter type.For fluids with a solids content,the velocity should be between 3 and 5m/s or 9 and 15ft/s to prevent deposits and minimize abrasion.Exact determination of flow velocityFor range setting purposes,the exact flow velocity can be determined using the flow table for each nominal pipe width.Example: v in m/sNominal pipe diameter DN150Desired measuring range200m3/hFrom the table we obtain for the flow velocity of 1m/sa flow rate of 63.617m3/h at DN150; for 200m3/hthe flow velocity v is:Example: v in ft/sNominal pipe diameter6”Desired measuring range1000 US GPMFrom the table we obtain for the flow velocity of 1ft/sa flow rate of 88.128 US GPM at 6”meter size;for 1000 US GPM the flow velocity v is:Flow tablesv = 1m/sMeter size Flow rate Meter size Flow rate DN mm m3/h DN mm m3/h2.50.017671250176.71 40.0452********.47 60.10179350346.36 100.28274400452.39 150.63617500706.86 20 1.131********.9 25 1.76717001385.4 32 2.89538001809.6 40 4.52399002209.2 507.068610002827.4 6511.94612004071.5 8018.09614005541.8 10028.27416007238.2 12544.17918009160.9 15063.617200011310 200113.10v = 1ft/sMeter size Flow rate Meter size Flow rate inch US GMP inch US GMP1/100.024********.801/80.03825012352.511/40.1530014479.813/80.3442516626.69 1/20.6120020979.21 3/4 1.3770241410.1 1 2.4480281919.211/4 3.8250322506.8 11/2 5.5080363172.6 29.7921403916.8 21/215.300485640.2 322.032567677.0 439.1686410027 561.2007212691 688.1288015667 8156.67Protection classes to IEC 529/EN 60529。
Molykote汽车行业应用_jshao
– 绝缘、密封、防潮、耐水 – 装配润滑
• Molykote® 产品
– G-5008 – 4 复合膏 – 111 复合膏
火花塞套
• 主要客户：Delphi
31
冷却风扇
• 轴承润滑要求：
– 工作温度范围广 – 使用寿命长
• Molykote®产品：
– 44M – 3451 – HP-300
• 主要客户：
39
4. 车身和内饰件
Exterior mirror Sunroof components Electronic door/lock systems Window regulator Control cables Door Locks Lighting
美国穆格型号
美国MOOG电液伺服阀穆格电液伺服阀 MOOG伺服阀穆格伺服阀穆格MOOG三级伺服阀MOOG直动式伺服阀D634-319C D634-399C D634-1003 D634-1005 D634-1007 D634-1008 D634-514A D634-557 D634-394CD634-1009 D634-1010 D634-1011 D634-1012 D634-1013 D634-1014 D634-1015 D634-1016 D634-1018D634-1019 D634-1023 D634-1024 D634-1025 D634-1026 D634-1027 D634-1028 D634-1029 D634-1031D634-1032 D634-1033 D634-1034 D634-1035 D634-1036 D634-1037 D634-1040 D634-1041 D634-1042D634-1043 D634-1045 D634-1046 D634-1047 D634-1049 D634-1050 D634-1051 D634-1052 D634-1053D634-1054 D634-1055 D634-1056 D634-1057 D634-1058 D634-1059 D634-1060 D634-3001 D634-301CD634-305C D634-307C D634-308C D634-317C D634-318C D634-322C D634-324C D634-326C D634-384CD634-327C D634-330C D634-331C D634-335C D634-341C D634-345C D634-346C D634-358C D634-361CD634-362C D634-368C D634-371C D634-372C D634-373C D634-374C D634-381C D634-383C D633Z7397D634-385C D634-386C D634-387C D634-388C D634-389C D634-390C D634-391C D634-392C D633Z7383D634-396C D634-397C D634-398C D634-400C D634-402C D634-403C D634-404C D634-405C D634-1001D634-406 D634-501A D634-502A D634-503 D634-504 D634-508 D634-511 D634-512A D634-513 D634-515 D634-516A D634-517 D634-518A D634-520A D634-521 D634-524A D634-525AD634-526D634-527A D634-528A D634-529A D634-530A D634-531 D634-532 D634-533 D634-534D634-536AD634-537A D634-538A D634-539 D634-540A D634-541 D634-542A D634-543A D634-544AD634-545D634-546A D634-547 D634-548 D634-550 D634-551 D634-552 D634-553A D634-554A D634-555 D634-558 D634-559 D634-560 D634K2000C D634K2001C D634K2002C D634K2003C D634K2004C D634K2005C D634K2006C D634K2007C D634K2008C D634K2009C D634K2010C D634K2011CD634K2012C D634K2013CD634K2014C D634K2015C D634K2016C D634K2017C D634K2018C D634K2019C D634K2020D634Z1020D634Z1021 D634Z1022 D634Z1038 D634Z1044 D634Z314C D634Z351C D634Z359CY D634Z360CD634Z360CYD634Z380C D634Z395C D634Z505A D634Z509 D634Z510 D634Z549A D633E703 D633E704D633E713AD633E714A D633E7365 D633E7366 D633E7411 D633K2000B D633K2001B D633K2002BD633K2003BD633K2005B D633K2006B D633K2007B D633K2008B D633K2009B D633K2010B D633K2011BD633K2012BD633K2013B D633K2014B D633K2015B D633K2017B D633K2018B D633K2019B D633K2020BD633K2021BD633K2022B D633K2023B D633K2024B D633K2025B D633K2026B D633K2027B D633K2028BD633K2029BD633K2030B D633K2031B D633K2032B D633K2033B D633K2034B D633K2035B D633K2036BD633K2037BD633K2038B D633K2039B D633K2040B D633K2041B D633K2042B D633K2043B D633K2044BD633K2045BD633K2046B D633K2047B D633K2048B D633K2049 D633K2050 D633K2051 D633Z303B D633Z305B D633Z313BD633Z317B D633Z338B D633Z348B D633Z371B D633Z379B D633Z480B D633Z506B D633Z528B D633Z529BD633Z532B D633Z539B D633Z557B D633Z570B D633Z585B D633Z586B D633Z587B D633Z588B D633Z589BD633Z590B D633Z7309 D633Z7324 D633Z7337 D633Z7352 D633Z7353 D633Z7361 B67728-001 B67728-002B67728-003 A03665-060美国Moog伺服阀说明:美国Moog伺服阀MOOG穆格伺服阀D633,D634系列，G761-3005，G761-3004，G761-3003,G761-3002，G761-3001,J761,J072，J869,G631 G761系列伺服阀 D791三级伺服阀 D661电反馈式伺服 72系列机械反馈伺服 D633/D634直动式伺服阀功率级阀型号/先导级 MOOG机能代号 D661-4651/ C41156-421 G35JOAA6VSX2HA D661-4652/ C4 1156-421 G15JOAA6VSX2HA D661-4636/C41156-421 G60KOAA5VSX2HA D661-4469C/C41156-421 G75KOAA6VS X2HA D661-4697C/C41156-421 G15JOAA5VSX2HA D661-4033/ C41156-421 P80HAAF6VSX2-A D661-4059/C41 156-411 P80HAAF6VSX2-B D661-4444C/C41156-421 G60JOAA6VSX2HA D661-4443C/C41156-421 G45J0AA6VS X2HA D661-4506C/C41156-421 G23J0AA6VSX2HA D661-4539C/C41156-421 G35JOAA5VSX2HA MOOG型号/先导级 MOOG机能代号 D662Z4311K/D630-072A P01JXMF6VSX2-A D662-4010/D061-8411 D02HABF6VSX2-A D662Z 4336K/D630-272D P01JXMF6VSX2-A MOOG型号/先导级 MOOG机能代号 D663Z4307K/D630Z067A P02JONF6VS X2-A D663-4007/D061-8412 L03HABD6VSX2-A MOOG型号/先导级 MOOG机能代号 D663Z4307K/D630Z067A P 02JONF6VSX2-A D663-4007/D061-8412 L03HABD6VSX2-A D634-341C R40K02M0NSS2 D634-319C R40KO2M0NS P2 D633-333B R16KO1F0NSS MOOG型号/先导级 MOOG机能代号 D791-5009/D761-2612 S16J0QA6VSB0-P D7 91-4025/ S25J0PA6VSX2-A D791-4001/待查 S25J0QB6VSX2-B D791-4002/D761-2617 S25J0QB5VSX2-B D791-4028/D761-2619 S25J0QB6VSX2-B D791-4046/D761-2619 S25J0QA6VSX2-B MOOG型号 MOOG机能代号 07 2-559A S15F0FA4VBL， 072-558A S22FOFA4VBL《新型号：072-1203-10》。
道康宁润滑剂摩力克总汇
【道康宁润滑剂】液压油 美国道康宁 MOLYKOTE®（摩力克 TM）特种润滑剂 美国道康宁 Dow Corning 大全Molykote 产品针对您的润滑问 题... 道康宁 MOLYKOTE Molykote G72/Molykote G/72 有机硅润滑脂 Molykote 产品-针对您的润滑问题的解决方案Dow Corning 4 compound Dow Corning 5 Dow Corning 7 compound、Dow Corning 7 Molykote 33 light/medium Molykote 41 Molykote 44 light/medium Molykote 55(M)/Molykote 55M Dow Corning 111 compound/Dow Corning 111 Dow Corning 4 Molykote 7348/Molykote7348 Dow Corning 340 导热硅脂/Dow Corning 340 Molykote G-5032/Molykote G5032 Molykote PG 21/Molykote PG21 Molykote PG54/Molykote PG 54 Dow Corning High-Vaccum Grease Molykote G-5008/Molykote G5008/Molykote G 500... Molykote 7508/Molykote7508 Molykote 7325/Molykote7325 Dow Corning 112 compound/Dow Corning112 Molykote 822M/Molykote 822 M道康宁 MOLYKOTE FORAFAC F1157/FORAFAC F 1157 氟碳表面活性 剂... FORAFAC F321/FORAFAC F321 FORAFAC 1268/FORAFAC® 1268 FORAFAC 1203/FORAFAC1203 FORAFAC 1157N/FORAFAC 1157 N道康宁 MOLYKOTE Molykote M-77 装配油膏/Molykote M-77 装配油 装配油膏膏... Molykote D Paste 装配油膏/Molykote DPaste 装配 油... Molykote G-n Plus/Molykote G-n Plus Molykote U paste/MolykoteU paste Molykote U-n/Molykote U n Molykote M-77/MolykoteM-77 Molykote G-Rapid plus (spray)/Molykote G-Rapi... Molykote G-n plus/Molykote G-n plus Molykote D paste(spray)/Molykote D paste spra...道康宁 MOLYKOTE Molykote P-1900/Molykote P1900 脂类油膏 Molykote P1500/Molykote P 1500 Molykote X /Molykote X Molykote TP-42/Molykote TP42 Molykote P40/Molykote P 40 Molykote E paste Molykote DX Paste Molykote CU-7439/Molykote CU-7439 润滑油膏道康宁 MOLYKOTE Molykote G-2001/Molykote G2001 润滑脂 Molykote 165LT/Molykote 165 LT/Molykote165LT Molykote 1122 (spray)/Molykote 1122spray Molykote BG20/Molykote BG 20 Molykote BG 555/Molykote BG555 Molykote BR 2 plus/Molykote BR 2plus Molykote FB180/Molykote FB 180 Molykote G-0010/Molykote G-0010 Molykote G 67/Molykote G67 Molykote G-6000/Molykote G6000 Molykote G-0100/Molykote G0100 Molykote G-0102/Molykote G0102 Molykote 1102/Molykote1102 Molykote G-1001/Molykote G1001 Molykote G3407Molykote G-3407/刹车卡钳润滑脂 Molykote G-4700/Molykote G4700 Molykote Longterm 00/Molykote Longterm00 Molykote Longterm 2 plus/Molykote Longterm 2p... Molykote Longterm W2/Molykote LongtermW2 Molykote Longterm 2/78G/Molykote Longterm 2/7... Molykote MKL-N(spray)/Molykote MKL-N spray Molykote Multilub/Molykote Multilub Molykote TTF52/Molykote TTF 52 Molykote® BR-2 Plus Multi-Purpose EP Grease Molykote G-407/Molykote G407 Molykote 8018/Molykote 8018 Molykote G-807/Molykote G807 Molykote G-0101/Molykote G-0101道康宁 MOLYKOTE Molykote PG-30L/Molykote PG30L 塑料用润滑脂Molykote YM103/Molykote YM-103 Molykote YM-103/Molykote YM 103 Molykote YM-102/Molykote YM102 Molykote PG663/Molykote PG-663 Molykote PG-662/Molykote PG662 Molykote PG661/Molykote PG-661 Molykote 6166/Molykote6166 Molykote PG75/Molykote PG 75 MOLYKOTE EM-70L/MOLYKOTE EM 70L Molykote G2003/Molykote G-2003 Molykote G 68/Molykote G68 Molykote EM-D110/Molykote EM-D110 Molykote EM-60L/Molykote EM 60L Molykote EM-50L/Molykote EM50L Molykote EM-30L/Molykote EM30L Molykote PG-602/Molykote PG602 MOLYKOTE(摩力克) PG-641/MOLYKOTE PG-641 MOLYKOTE G-1023/MOLYKOTE G1023MOLYKOTE G-1031/MOLYKOTE G-1031 GREASE MOLYKOTE G-1050 GREASE/MOLYKOTE G-1050 Molykote SK-623/Molykote SK 623 Molykote 7514/Molykote 7514 MOLYKOTE® AG-650/MOLYKOTE AG-650 Molykote X5-6020/Molykote X5 6020 Molykote PG65/Molykote PG 65 molykote EM-10L grease/molykote EM-10L MOLYKOTE® PG-671/MOLYKOTE PG-671 MOLYKOTE EM-60L/MOLYKOTE EM 60L MOLYKOTE EM-50L/MOLYKOTE EM 50L MOLYKOTE EM-40L/MOLYKOTE EM 40L MOLYKOTE EM-40L/MOLYKOTE EM 40L MOLYKOTE EM-30L/MOLYKOTE EM 30L Molykote G-1017/Molykote G1017 Molykote MI-60/Molykote MI 60 Molykote PD900/Molykote PD 900 Molykote BG 87/Molykote BG87 Dow Corning FS 1265 Fluid Molykote FS1292/Molykote FS 1292 Molykote FS3451/Molykote FS 3451 MOLYKOTE® HF-30 OIL/MOLYKOTE HF-30 Molykote HP-300(spray)/Molykote HP-300 Molykote HP-500/Molykote HP500 Molykote 6169/Molykote6169道康宁MOLYKOTE 含氟 润滑剂 Molykote PD910/Molykote PD 910 molykote hp-300 Molykote PD910/Molykote PD 910 Molykote PD930/Molykote PD 930 Molykote PD920/Molykote PD 920 MOLYKOTE HF-50/MOLYKOTE HF 50 Molykote HF-50/Molykote HF 50 MOLYKOTE L-8008/MOLYKOTE®）L-8008 Molykote HF-60/Molykote HF-60 Molykote G8007/Molykote G8007 Molykote HP-870/Molykote HP-870道康宁 MOLYKOTE Molykote PTFE-N (spray) 减摩涂层 Molykote D708/Molykote D 708 Molykote D96/Molykote D 96 Molykote D31/Molykote D 31 Molykote D3484/Molykote D 3484 Molykote D321R (spray)/Molykote D321 R (spray... Molykote D-10/Molykote D10 Molykote 7409/Molykote7409 Molykote 7405/Molykote7405 Molykote 7400/Molykote7400 Molykote 3402C/Molykote3402C Molykote 3400A(Leadfree) Molykote 106 /Molykote106 Molykote Z Powder Molykote Microsize、Molykote Microsize道康宁 MOLYKOTE 二硫化钼粉末道康宁 MOLYKOTE Molykote W15/Molykote W 15 液体分散液 Molykote M55 plus/Molykote M55 Molykote A(spray)/Molykote A Molykote 557 (spray)/Molykote 557道康宁 MOLYKOTE Molykote L-0122FG/Molykote L-0122 FG 高温链条油 Molykote M30/Molykote M 30 Molykote S-1500/Molykote S1500 Molykote S-1501/Molykote S1501 Molykote S-1502/Molykote S1502 Molykote S-1503/Molykote S1503 Molykote S-1504/Molykote S1504 Molykote L-1428/Molykote L1428 Molykote L-0115/Molykote L0115 Molykote CO 220/Molykote CO220 Molykote L-0122/Molykote L 0122 Molykote L-1428/Molykote L-1428 Molykote L-0132/Molykote L 0132 Molykote L-0132FG/Molykote L-0132 FG Molykote L-0146/Molykote L-0146 Molykote L-0146FG/Molykote L0146 FG Molykote L-0168/Molykote L0168 Molykote L-1168/ Molykote L1168 Molykote L-0460FG/Molykote L-0460 FG Molykote H 1468FG/Molykote H 1468 FG Molykote L-0115FG/Molykote L-0115FG Dow Corning 702/Dow Corning702 Dow Corning® 316 Molykote Supergliss spray Molykote S-1000/11/02/03/04spray Molykote Polygliss-N spray Molykote Omnigliss(spray) Molykote Multigliss 5 in 1(spray) Molykote Metal Protector plus (spray) Molykote Metal Cleaner spray/Brake Cleaner Molykote Metalform Molykote HTP道康宁MOLYKOTE 特种 产品 Molykote HTF、Molykote HTF Molykote Zinc Coating L-0500(spray) 道康宁二甲基硅油 PMX-200 Dow Corning 705 扩散泵硅油 Dow Corning 704 扩散泵硅油 Dow Corning 702 扩散泵硅油 Molykote L-0510FG 多功能油 Molykote L-0510 多功能油* Molykote L-0568 多功能油* Molykote L-1368FG 合成液压油 Molykote L-0532FG 多功能油* Molykote L-1346FG 合成液压油 Molykote L-0368FG 液压油 Molykote L-0346FG 液压油 Molykote L-0346 液压油道康宁 MOLYKOTE 扩散泵硅油 道康宁 MOLYKOTE 液压系统润滑 油... 道康宁 MOLYKOTE Molykote L-3246 合成压缩机油 压缩机及真空 泵... Molykote L-1240 半合成压缩机油 Molykote L-1232 合成压缩机油 Molykote L-1232FG 合成压缩机油 Molykote L-1246 合成压缩机油 Molykote L-1246FG 合成压缩机油 Molykote L-1268 合成压缩机油 Molykote L-0246 螺旋压缩机油 Molykote L-3232 合成压缩机油 Molykote L-1605FG/Molykote L-1605 FG 合成阻尼 油... Molykote L-4646 合成高温压缩机油 Molykote L-4610 合成活塞压缩机油 Molykote L-0610 真空泵油 Molykote L-1668FG/Molykote L-1668 FG 真空泵油 Molykote L-0668 氨冷冻压缩机油 Molykote L-4640 合成压缩机清洗油 Molykote L-1210 合成压缩机油道康宁 MOLYKOTE Molykote L-0510FG/Molykote L-0510 FG 多功能润滑油 Molykote L-0510/Molykote L0510 Molykote L-0568FG/Molykote L0568 FG Molykote L-0532FG道康宁 MOLYKOTE Molykote 食品级工业润滑油 食品级润滑剂Molykote G-4501/Molykote G4501 Molykote White EP/Molykote WhiteEP Molykote Separator Spray Molykote P1900/Molykote P 1900 Molykote G-4500(spray) Molykote G-0052FG /Molykote G-0052FG Molykote G-0051FG,/Molykote G-0051FG Molykote G-0050 FG/Molykote G-0050FG Molykote Food Grade Spray Oil Molykote Food Grade EP2/Molykote Food Grade E... Molykote Food Grade EP1/Molykote Food Grade E... Molykote Food Grade E 0/Molykote Food Grade E...道康宁 MOLYKOTE Dow Corning DC735/737/7091/1200 工业硅酮密封 胶... Dow Corning DC730/732/734/736 道康宁 DC-734 密封胶 道康宁-DC732 密封胶 道康宁 995 硅酮结构密封胶 DC786 密封胶/DC832 密封胶/DC866 流动性密封胶 /DC1...DOW CORNING(R) 8888道康宁 MOLYKOTE道康宁润滑剂润滑油产品总汇...。
Molykote特种润滑产品系列
16
G-4700全合成极压润滑脂
• 亮点：高承载能力，四球焊接负荷>400kg • 组成
– 聚α烯烃(PAO)基础油，锂复合稠化剂，二硫化钼及其它增 强剂
• 特征
– NLGI #2 – 服务温度-40~180°C
• 应用
– 齿轮、销轴、驱动螺杆、冲击载荷、振动、以及任何需要 长效重载润滑脂场合
17
• 空压机油
– L-1210, L-1232, L1246, L-1268, L-4611
8
Molykote特种润滑剂之一
润滑脂
代表性润滑脂产品
• Molykote提供数十种润滑脂，从车轮轴承用的EP脂到极 端化学与温度条件下使用的高技术PTFE稠化PFPE润滑脂。 • 代表性产品
– – – – – – – BR2+，Longterm 2+通用润滑脂 G-4700，G-4500，高/低温，高负载，多用途，抗水 BG-20，高速合成润滑脂 G-005xFG，白色食品级多用途润滑脂 硅脂：33，44，41 氟硅脂：1292, 3451, 3452 全氟聚醚脂：HP-300, HP-500, HP-870
G-4500多用途合成脂
• 亮点：白色合成润滑脂，符合NSF H-1食品级要求 • 组成
– PAO基础油 – 铝复合皂基 – PTFE强化，增粘剂
• 特征
– NLGI #2 – 四球焊接负荷>315kg – 服务温度-50~150°C
• 好处
– 承载能力高，抗磨损性好，润滑寿命长 – 与多种塑料及橡胶材料兼容
– 四球焊接负荷
• HP-870, >4900N • HP-300, 3330N
– 非凡的耐化学品性能、热稳定性、兼容性 – HP-300不含添加剂(NSF H1)
Magman II 操作手册说明书
MAGMAN II Operational Manual1.0 General Information (4)2.0 Magman You tube Channel and Contact details (4)Part 1 Magman Explosives Inventory Web (4)3.0 Magman Web System (4)3.1 Software Specifics (4)3.2 System Security Levels (5)3.3 Magman Web Hierarchy (6)4.0 Basics functionality of the Magman System (7)4.1 Adding a User to the Magman system (7)4.2 Assigning a user to the Site (10)4.3 Assigning a user to the Magazine (11)5.0 Adding locations to the tablet (12)5.1 Adding Single Locations (12)5.2 Adding Multiple Locations (13)6.0 Adding inventory items to a magazine. (14)7.0 Adding Production Blasts (16)Part 2 Magman Explosives Inventory Tablet (19)8.0 Magman Tablet - Getac F110 Intrinsically Safe Tablet (19)8.1 Battery (19)8.2 Synching the Magman Tablet (20)8.3 Connecting the tablet to the internet (20)8.4 Sync (22)8.5 Tablet Keyboard (22)8.6 Web Magazine transactions (23)9.0 Tablet Transactions (23)9.1 Take / Return from the Magazine (23)9.2 Saved Take (25)9.3 Production Plans (25)Figure 1. Magman II Hierarchy (65)Figure 2. Example of Magman II Hierarchy (6)Figure 3. Getac tablet keyboard button (7)Figure 4. Client web screen (8)Figure 5. Add User Button (8)Figure 6. User set up (9)Figure 7. Assigning user to a group (10)Figure 8 Assigning the user to the site (11)Figure 9. Assigning the user to the site (11)Figure 10. Assigning the user to the site (11)Figure 11. Assigning the user to the Magazine (12)Figure 12 Assigning the user to the Magazine (12)Figure 13. Assigning the user to the Magazine (13)Figure 14. Add a single location (13)Figure 15. Add multiple locations (14)Figure 16. Multiple location upload template (14)Figure 17. Confirmation of the uploads (15)Figure 18. Uploading new inventory items to the magazine (15)Figure 19. Current magazine Inventory items (16)Figure 20. Importing Locations (16)Figure 21 Adding / Removing Inventory from your Magazine (17)Figure 22 Adding / Removing Inventory from your Magazine (17)1.0 General InformationThe Magman Electronic Explosives Inventory System consists of two separate components : Part 1.Website which controls the Magman system, stores and backs up the system database, allows the generation of inventory reports, controls the deployment ofinventory items, personnel and locations onto the tablet.Part 2.Tablet which is a simple visual inventory control system designed for operators to record transactions, complete stock takes and check running inventory levels.Part 1 of this manual addresses the Magman website2.0 Magman Youtube Channel and Contact detailsMagman has a Youtube Channel with a variety of training videos. Search for Youtube Magman or enter the following link into your webbrowser.https:///channel/UCeuonp1a9wU5pGGqChx9GeQFor enquiries, the Magman team can be contacted at ***************.au or Ph 1300 624 626. Part 1 Magman Explosives Inventory Web3.0 Magman Web SystemWebsite : https://XXXX The file path is provided with your system set up.3.1 Software SpecificsThe Magman software uses the Windows 10 platform in conjunction with Microsoft’s Azure Database hosted on the east coast of Australia. Magman web hosted on a secure https:// web site.The program language for Magman II is - Type.script (Java Script) and .core (Backend web) It is recommended that clients establish a regular back up process to ensure compliance with their own internal governance requirements.3.2 System Security LevelsThe security levels are set up on the web, prior to dispatch of the system to site.The security levels can be set to allow personnel to have access to the tablet, the web or both.The functionality which is available through the security settings include:Managing the addition of Magman Users and assignment to the pre-determined security levels.Manage the inventory on the system through the addition / removal of inventory items in each magazine.Allowing the re-set of personal details.Addition of inventory items from the global inventory list.Establish customised reporting templates.Establish customisable definable fields or questions for users to provide specific data.The data captured in the system for each transaction includes:DateTimeUserInventory movementLocation for the items3.3 Magman Web HierarchyFigure 1. Magman II HierarchyThe Magman II system is set up with hierarchical levels to allow the control of security levels. The hierarchy allows companies to customise the security levels assigned to the personnel within their business.Figure 2. Example of Magman II HierarchyThe hierarchy levels are important for the client administrators to understand. It is also important to understand the definition of the systems:Users – person assigned to add / remove items on the tablet and/or the web browser. Contact – A person who is contacted in relation to the magazine licensing or in case of an emergency.4.0 Basics functionality of the Magman SystemBelow is an outline of the basic functionality available on the web browser.4.1 Adding a User to the Magman systemOn the main screen of the Web browser https://XXXX/Login , you will have access to the Icon “User Management”. This Icon allows you to add new users into the system.Great Gold Resources Pty Ltd(Client)Desperate Gold Mine(Site)DGM UG Mag (Mag)DGM Surface Mag (Mag)Spotty Gold Mine(Site)SGM 13L Mag (Mag)SGM 45L Mag (Mag)DGM UG Mag2 (Mag)Figure 4. Client web screenFigure 5. Add User ButtonFigure 6. User set upPopulate the relevant fields Note: If a person is to operate at an Admin level they will require a unique email address to be added to the system. (The is driven by selecting Tablet / web or both)Figure 7. Assigning user to a groupSelect the relevant group for the individual. This will provide them with the level of access / security rights they have available to them.4.2 Assigning a user to the SiteTo assign the individual to the operator, client, select the Clients.Figure 8 Assigning the user to the siteOn the Site Screen, click on the Pencil Icon -> select the User Access.Figure 9. Assigning the user to the siteClick on the check box adjacent to the person who you want to assign to the Site andFigure 10. Assigning the user to the site4.3 Assigning a user to the MagazineTo assign a user to the Magazine, select the magazine which you want to add the person to. (Refer to the following screens).Figure 11. Assigning the user to the MagazineSelect the pencil Icon on the Magazine screen.Figure 12 Assigning the user to the MagazineCheck the box adjacent to the User you want selected for that magazine.Figure 13. Assigning the user to the MagazineOnce the tablet is synced, the User’s name will appear on the tablet.5.0 Adding locations to the tabletThere are two ways of entering locations to the Magman system :1.Upload bulk locations,2.Upload individual locations.5.1 Adding Single LocationsIn the Magazine screen on the web, Select the “Locations” tab (refer above on how to navigate to this screen)Figure 14. Add a single locationSimply select the icon and type in the name of the location and Save.5.2 Adding Multiple LocationsTo add multiple locations follow the instructions below:The multiple addition of locations is done through the use of an excel template. The easiest way to do this is to maintain the excel template to update locations as required.Select the export Locations tab.Figure 15. Add multiple locationsWhen you activate the “Location Export” the following template will be produced.Figure 16. Multiple location upload templateTo add locations, add additional rows into the excel template, completing each of the columns. Once completed, simply use the “Locations Import” and select the excel template file you have just populated.You will receive the following screen confirming the imported locations.Figure 17. Confirmation of the uploads6.0 Adding inventory items to a magazine.The Magman system contains a database of standard explosive inventory items which can be downloaded into individual magazines.Select “Inventory Item Management” from the Web screen.Figure 18. Uploading new inventory items to the magazineA screen will appear which shows your current inventory items. These items are specific to your magazine/s.To load additional items. SelectFigure 19. Current magazine Inventory itemsSelect the inventory items from the global list, by checking the “Import” box adjacent to the inventory item/s.Figure 20. Importing LocationsSelect icon.These products are now available to be selected in each of the magazines.To assign the inventory into the individual magazines, go to the magazine you want to add inventoryto and selectFigure 21 Adding / Removing Inventory from your MagazineCheck the boxes adjacent to the inventory item to be included into the magazine.Figure 22 Adding / Removing Inventory from your Magazine7.0 Adding Production BlastsProduction blasts can be entered into the Magman web. Once sync’ed the production blast will appear on the Magman Web.To add a production blast to the system, go to the Magazine on the web browser. Select Add Production Plan.Figure 23 Add production PlanEnter the products for the blast.Figure 24 Enter in Explosives and Detonators for the Production blast.Name the blast andFigure 25 Enter in the name of the Production Blast name and detailsOnce the tablet is synced the production blast will be available on the tablet for the operators to select.Part 2 Magman Explosives Inventory Tablet8.0 Magman Tablet - Getac F110 Intrinsically Safe TabletThe Magman Mining Software – Explosives Stock control system is supplied on a Getac F110 tough intrinsically safe tablet.The tablets have undergone RF/EM testing in a NATA accredited laboratory, to quantify the frequencies emitted from the tablet. The tablets do not emit any intentional emissions such as Bluetooth, WIFI, 3G, 4G, etc.The Getac tablets comply to United States Military Standard 810, which provides certification that the tablet can withstand duty under harsh / extreme conditions.The test reports and tablet certificates are available to clients to complete their own site risk assessment.For further details, refer to the Getac Operators manual supplied with the tablet.8.1 Battery.The below indicators identify the charge levels of the tablet. Note : The Getac F110 ATEC have the batteries screw in place so they cannot unintentionally be removed.Figure 26 Battery indicator on the tablet8.2 Synching the Magman TabletThe Magman tablet must be sync’ed to the cloud for the information to be uploaded to the cloud and download any changes which have been made in the cloud.It is recommend that you sync the tablet on a daily basis.The last sync date appears on the bottom left hand corner of the tablet.8.3 Connecting the tablet to the internet.As there is no WIFI or 3G/4G capabilities on the tablet, it needs to be plugged into the internet using the supplied connector. Plug the USB/Ethernet adaptor into an active Ethernet (Blue Cat5 Computer cable) and the USB port on the upper left hand side of the tablet (Under the lockable flap).Figure 27 USB Port on the Getac F110Figure 28 USB / Ethernet ConnectorOnce logged into the tablet, Internet Online wording appears in the lower right hand corner of the screen, indicating the tablet is ready to be sync’ed.Figure 28 Ensure the tablet “Internet Online” indicator is on prior to sync’ing the tablet8.4 SyncOnce logged in, tap the “Sync” icon. The sync routine will scroll down the screen.Check the sync process progresses through to the “Sync Complete”. If not, contact your site Magman Administrator or email ***************.au8.5 Tablet KeyboardThe keyboard on the tablet should automatically pop up whenever text is required to be entered into the system.If the keyboard doesn’t automatically pop up, the button on the side of the tablet with three horizontal dots will force the keyboard to appear.Figure 29. Getac tablet keyboard button8.6 Web Magazine transactionsIf, for any reason the tablet is unserviceable, transactions can be entered directly into the Magman web browser.9.0 Tablet Transactions9.1 Take / Return from the MagazineFigure 30. Magman Tablet MenuTo remove product from the magazine, simple tap on the Icon. The product list will appear. Select the quantity of each item to be removed from the magazine.Figure 31. Magman Take ScreenSelectEnter in the Location and confirm the Items being removed from the magazine are correct. Select . The transaction is now recorded in the data base.Figure 32. Magman Take Process ScreenThe function is the same in reverse.9.2 Saved TakeThe is used to store the explosives and detonators for standard development headings. These are set up by the Magman Administrator.In the example below the 5.5 x 5.5 Decline heading has the detonators and explosives pre-populated. This makes it much quicker for operators to complete a transaction for standard development headings.Select the development profile and follow the Take process.9.3 Production PlansThe engineers will pre-load each production blast into the Magman web, which is transferred to the tablet when it is Synced.Figure 33. Magman Saved TakeThe operator selects the Production Plan Icon. They can then select the desire production plan, which has the Take screen pre-populated with the required detonators and explosives.Follow the Take process.。
电力克泰国有限公司产品说明书：电力EME3500SA顶部冰箱-空调
Item PNC ELC Brand Model MarketSPARE PARTS LISTFreestanding fridge-freezers, top freezers3713A 925053050 00 Electrolux EME3500SA VNE Electrolux Thailand Co.,Ltd. 1910 Electrolux Building New Petchburi Rd. Bangkapi HuaykwangBangkok , 10310 Tel : +662 725 9000Publication-No. 130709Freestanding fridge-freezers,top freezersSAFETY WARNINGAlways turn off and unplug the machine before detaching any parts.When servicing machines, do not removeANY detachable parts while the machine is powered. The reason is internal faults may cause shorts to components that are normally at low voltage presenting a shock hazard.A 925053051 00 Electrolux EME3500SA PHH A 925053052 00 Electrolux EME3500SA SGE A 925053053 00 Electrolux EME3500SA MYH A 925053054 00 Electrolux EME3500SA THE A 925053086 00 Electrolux EME3500SA IDHModel : PNC :Ex. View DrawingEME3500SACabinet Assembly49Pos.Part No. DescriptionE M E 3500P N C 9250 E M E 3500P N C 9250E M E 3500P N C 9250E M E 3500P N C 9250 E M E 3500P N C 9250 E M E 3500P N C 92501 811924701CABINET FOAMED MD350 GRVN 1 1 811924601 CABINET FOAMED MD350 GRPH 1 811924501 CABINET FOAMED MD350 GRSG 1 811924401 CABINET FOAMED MD350 GRMY 1 811991901 CABINET FOAMED MD350 GR1 2 811999101 HINGE BOTTOM BASE RIGHT 1 1 1 1 1 1 3 811996201 FEET BASE HINGE 1 1 1 1 1 1 4 811998901 FEET LEVER2 2 2 2 2 2 5 811949503 SCREW TRUSS 4.2x13 6 6 6 6 6 6 6 811999001 FEET BASE1 1 1 1 1 1 7 811943001 SWITCH DOOR TF DOUBLE 1 1 1 1 1 1 8 811943601 SWITCH DOOR2 2 2 2 2 2 9 811981301SUPPORT HEATER MD1 1 1 1 1 811981402 SUPPORT HEATER TF R600a1 10 811981801HEATER DEFROST R134A 240V 1 1 1 1 1 811981701 HEATER DEFROST R600A 240V1 11 811981201COVER HEATER R134A 1 1 1 1 1 811981101 COVER HEATER R600a 1 12 811980401 CLAMP NTC EVAPORATOR 1 1 1 1 1 1 13 811944701 HARNESS THERMO FUSE 1 1 1 1 1 1 14 811948501 CABLE TIES 2.5x1204 4 4 4 4 4 15 811982002 EVAPORATOR 7 PASSES 6.5 1 1 1 1 1 1 16 811981501 RETAINER THERMAL FUSE 1 1 1 1 1 1 17 811974401 SHROUD FAN1 1 1 1 1 1 18 811974301 BRACKET SHROUD FAN 1 1 1 1 1 1 19 811972801 GROMMET FAN SIDE2 2 2 2 2 2 20 1446048 GROMMET , FAN MOUNTING 2 2 2 2 2 2 21 1451299 BLADE ASSY FAN1 1 1 1 1 1 22 811973301MOTOR FAN 240V/50HZ 1 1 1 1 1 811973302 MOTOR FAN 240V/60HZ 1 23 242585005 PCBA MAIN ERF2002 1 1 1 1 1 1 24 811968401 HOUSING BOX PCB 1 1 1 1 1 1 25 811968301 COVER BOX PCB1 1 1 1 1 1 26 811974701COVER EVAPORATOR FRONT TF1 1 1 1 1 1 811971901 COVER EVAPORATOR MD 1 1 1 1 1 1 28 811972601COVER MID CONNECTOR HOUSIN1 1 1 1 1 1 29 811930402 COVER DEODORIZER BLUE3 3 3 3 3 3 30 811972201 DUCT EVAPORATOR REAR MD111111Pos.Part No. DescriptionE M E 3500P N C 9250 E M E 3500P N C 9250E M E 3500P N C 9250E M E 3500P N C 9250 E M E 3500P N C 9250 E M E 3500P N C 925031 811972901 DUCT MID EPS REAR MD 1 1 1 1 1 1 32 811973101 DUCT MID EPS FRONT MD 1 1 1 1 1 1 33 811969301 BAFFLE DOUBLE MD1 1 1 1 1 1 34 811951901 TAPE ALUMINUM EVC REAR MD1 1 1 1 1 1 35 811971601 COVER SCREW5 5 5 5 5 5 36811974201COVER MULTIFLOW FRONT LUX MD S1 1 1 1 1 1 37 811973401 COVER MULTIFLOW SLIDE 1 1 1 1 1 1 38 811973201 COVER MID FRONT MD1 1 1 1 1 1 39 811944801 HARNESS MULTIFLOW TF LUXUR 1 1 1 1 1 1 40 811974001 DUCT MULTIFLOW TF SMALL 1 1 1 1 1 1 41 811930301 DEODORIZER NANO COPPER 1 1 1 1 1 1 42 811943801 PCBA LIGHTING LED HSLB3 3 3 3 3 3 43 811971501 LENS MULTIFLOW TF 1 1 1 1 1 1 44 811971201 LENS FREEZER MD 350 2 2 2 2 2 2 45 811999201 HINGE CENTRE RIGHT 2 2 2 2 2 2 46 811999401 HINGE TOP RIGHT1 1 1 1 1 1 47 811998801 HINGE TOP COVER RIGHT GR 1 1 1 1 1 1 48 811949401 SCREW TRILOB M5x16 8 8 8 8 8 8 49 811942601 HARNESS SENSOR111111Model : PNC :Ex. View DrawingEME3500SACabinet InteriorParts Assembly25Pos.Part No. DescriptionE M E 3500S A P N C 925053050 E M E 3500S A P N C 925053051E M E 3500S A P N C 925053052E M E 3500S A P N C 925053053 E M E 3500S A P N C 925053054 E M E 3500S A P N C 9250530861 811956701 T&S ASSY WHITE 1 1 1 1 1 12 811956801 FRAME ICE T&S 1 1 1 1 1 13 243262600 T&S ICE CUBE TRAY 2 2 2 2 2 24 811957001 SUPPORT ICE T&S 1 1 1 1 1 15 243262903 KNOB ICE T&S WHITE 2 2 2 2 2 26 811956601 BIN ICE1 1 1 1 1 1 7 1451543 SPRING TWIST&SERVE2 2 2 2 2 2 8 811957201 LID FREEZER SHELF 60W LUX 1 1 1 1 1 1 9 811957701 SHELF FZR FOLDABLE FRONT 60W1 1 1 1 1 1 10 811957501 SHELF FZR FOLDABLE REAR60W1 1 1 1 1 1 11 811957901 SHELF FZR ASSY 60W1 1 1 1 1 1 12 811956201 DRAWER MIDDLE BODY MD350 1 1 1 1 1 1 13 811958101 TRAY CHILL ROOM 60W L 1 1 1 1 1 1 14 811955401 SHELF SPLIT ASSY 60W LUX 1 1 1 1 1 1 15 811958701 SHELF FC ASSY 60W1 1 1 1 1 1 16 811959001 COVER CRISPER ASSY 60W 1 1 1 1 1 1 17 807323001 CRISPER BODY 60W LUX 1 1 1 1 1 1 18 811960201 CRISPER FRONT TF 60W 1 1 1 1 1 1 19 811959801 CRISPER HANDLE TF 60W 1 1 1 1 1 1 20 811959601 DIVIDER CRISPER TF 60W 1 1 1 1 1 1 21 811967901 HOUSING PCBA VLIGHT1 1 1 1 1 1 22 807238301 LIGHT GUIDE N-LIGHT 4LED 1 1 1 1 1 1 23 807114501 LENS N LIGHT 4LED 1 1 1 1 1 1 24 807114301 PCB N LIGHT 60W 4LED 1 1 1 1 1 1 25 811956401 SHELF MID ASSY MD350 1 1 1 1 1 1 26 811967801 COVER PCBA VLIGHT 1 1 1 1 1 1 27 811949501 SCREW TRUSS 4.2x35 1 1 1 1 1 1 28 811958501 LID CHILL ROOM 60W1 1 1 1 1 1 29 811956001 DRAWER MIDDLE FRONT MD350 1 1 1 1 1 1 30 811960801 DRAWER HANDLE MID MD350 1 1 1 1 1 1 31 811959201 KNOB HUMIDIFIER111111Model : PNC :Ex. View DrawingEME3500SASystemcompartment Assembly2.1Pos.Part No. DescriptionE M E 3500S A P N C 925053050 E M E 3500S A P N C 925053051E M E 3500S A P N C 925053052E M E 3500S A P N C 925053053 E M E 3500S A P N C 925053054 E M E 3500S A P N C 9250530861 811998401 BASE COMPRESSOR 60W1 1 1 1 1 12 811979402 COMPRESSOR ACC GVY57AG1 811979301 COMPRESSOR ACC HXK95AA 1 811979003 COMPRESSOR WANBAO ASF 1 1 1 1 2.1 807305701 TERMINAL BLOCK ACC1 1 807306201 TERMINAL BLOCK HXK 1 807280401 BLOCK TERMINAL WANBAO 1 1 1 1 3 811978901 GROMMET COMPRESSOR 4 4 4 4 4 4 4 811998601 CLAMP COMPRESSOR2 2 2 2 2 2 5 811978201 CLAMP DRYER 1 1 1 1 1 1 6 811945601 CAPACITOR 4UF1 1 1 1 811945602 CAPACITOR 4UF 4.8mm1 1 7 811943301 POWERCORD REFRIGERATOR VN1 811943401 POWERCORD REFRIGERATOR PH 1 1 811943201 POWERCORD REFRIGERATOR SG 1 1 811943101 POWERCORD REFRIGERATOR TH 1 8 811942901 HARNESS EARTH1 1 1 1 1 1 9 811949301 SCREW TRILOB M3x102 2 2 2 2 2 10 1441189 DRYER1 1 1 1 1 1 11 1401884 TUBE PROCESS2 2 2 2 2 2 12 811983601 TUBE DISCHARG EXTENSION ACC11 1 1 811983501 TUBE DISCHARG EXTENSION ACC2 1 811983301 TUBE DISCHARG EXTENSION WANB 1 1 13 811982501 TUBE SUCTION EXTENSION ACC11 1 1 811982401 TUBE SUCTION EXTENSION ACC2 1 811982201 TUBE SUCTION EXTENSION WANBA 1 1 14 811978101 PAN DRAIN WATER ACC1 1 1 811977901 PAN DRAIN WATER HXK 1 896113194 PAN DRAIN WATER WANBAO 1 1 15 811949401 SCREW TRILOB M5x162 2 22 2 2Model : PNC : Ex. View DrawingEME3500SA Door Assembly5.15.25.36.16.3 6.2Pos.Part No. DescriptionE M E 3500S A P N C 925053050 E M E 3500S A P N C 925053051E M E 3500S A P N C 925053052E M E 3500S A P N C 925053053 E M E 3500S A P N C 925053054 E M E 3500S A P N C 9250530861 811933901 DOOR FOAMED FC MD350 SS 1 1 1 1 1 12 811933701 DOOR FOAMED MID MD350 SS 1 1 1 1 1 13 811934801 DOOR FOAMED FZR MD350 SS 1 1 1 1 1 14 811986804 RAIL DOOR SUPPORT 60W SILV 1 1 1 1 1 1 5.1 811988515 GASKET FC MD350 1 1 1 1 1 1 5.2 811988514 GASKET MID MD350L 1 1 1 1 1 1 5.3 811988502 GASKET FZR TF60W1 1 1 1 1 1 6.1 807439106 HANDLE FC MD ASSEMBLY 1 1 1 1 1 1 6.2 807439105 HANDLE FC MID ASSEMBLY 1 1 1 1 1 1 6.3 807439104 HANDLE FC FZR ASSEMBLY 1 1 1 1 1 1 7 811962002 BIN DOOR BOTTLE ASSY 60W 1 1 1 1 1 1 8 811961501 BIN DOOR FLEX 1/2 ASSY 1 1 1 1 1 1 811961401 BIN DOOR FLEX 2/3 ASSY 2 2 2 2 2 2 9 807489801 TRAY EGG 10 1 1 1 1 1 1 10 811960701 BIN DAIRY ASSY 1 1 1 1 1 1 12 811960601 CLIP BAG DOOR2 2 2 2 2 2 13 811962102 BIN DOOR SHALLOW ASSY 60W 1 1 1 1 1 1 14 811967401 DOOR COMPLETE UI ASSY TF 1 1 1 1 1 1 15 811969601 PCBA UI1 1 1 1 1 1 16 811988701 BEARING AUTO CLOSER R 3 3 3 3 3 3 17 811948801 SCREW COUNTERSUNK M4.8x19 3 3 33 3 3Model : PNC : - 11 -EME3500SA SAFETY WARNINGAlways turn off and unplug the machine before detaching any parts. When servicing machines, do not remove ANY detachable parts while the machine is powered. The reason is internal faults may cause shorts to components that are normally at low voltage presenting a shock hazard.。
汽车英语缩写大全
汽车英语缩写大全进口汽车维修技术缩略语词典＊C Degrees Celsius摄氏度＊F Degrees Fahrenheit 华氏度＊D＊Drive 驱动,驾驶，行驶,行车*N* Neutral Position 空档*P＊*PARK*Position P档，停车档*P* *PARK＊Position P（驻车）档位置O2 Oxygen 氧气2WD Two—Wheel Drive 两轮驱动4WD Four-Wheel Drive四轮驱动4WS Four-Wheel Steering四轮转向AA A—post, A—pillar A柱A Amperes 安培, 电流A *Amper *Ammeter *Advance ＊安培*电流表*提前A.I。
R。
Air Injection Reactor 空气喷射反作用器A.M。
Above-Mentioned 上述的A/C Air Conditioning空调A/C A/C Amplifie 空调放大器A/C CLTCH。
A/C Clutch空调离合器A/CL Air Cleaner 空气滤清器A/CL-BM Air Cleaner Bimetal Sensor空气滤清器双金属传感器A/CL-CWM Air Cleaner Cold Weather Modulator 空气滤清器低温调节器A/CL—DV Air Cleaner Duct Valve Vacuum Motor 空气滤清器导管阀真空马达A/CL—TSOV Air Cleaner Temperature Sensor Override Valve空气滤清器温度传感器超压阀A/CL-VCD Air Cleaner Vacuum Control Delay 空气滤清器真空延迟控制A/CL-VCV Air Cleaner Vacuum Control Valve 空气滤清器真空控制阀A/CL—VM Air Cleaner Vacuum Motor空气滤清器真空马达A/F Air-Fuel Ratio空燃比A/T Automatic Transaxle Or Transmission 自动变速箱AA Automobile Association （UK)英国汽车协会AAA American Automobile Association美国汽车协会AAC Auxiliary Air Control辅助空气控制AAC Automatic Amplitude Control自动振幅控制AACV Auxiliary Air Control Valve辅助空气控制阀AAD Auxiliary Air Control Device 辅助空气装置AAE America Association of Engineers 美国工程师协会AAMVM American Association of Motor Vehicle Manufacturers美国汽车制造者协会AAP Auxiliary Accelerator Pump 辅助加速器泵AAP Auxiliary Accelerating Pump辅助加速泵AAP Ambient Absolute Pressure外界绝对压力AAS Aspirator Air System吸气（真空）控制系统AAS Auto Adjust Suspension 自动调节悬挂AAS Air Adjust Screw空气调整螺丝AAS American Astronautical Society 美国宇宙航行学会AAS Air Adjust Screw空气调节螺钉AASHTO American Association of State Highways and Transportation Officials 美国各州公路及运输公务员协会AAV Anti Afterburn Valve 防止后燃阀AB Air Bleed 空气泄放ABA Air Bleed Actuator空气排放执行器（电磁阀)ABCV Air Bleed Control Valve空气泄放控制阀ABDC After Bottom Dead Center在下止点后ABG Alcohol Blended Gasoline掺酒精的汽油ABN Airborne Noise 空气传播的噪音ABP Air Brake Proportioing （valves) 空气制动比例分配（阀）ABRS Air Bag Restraint System 安全气囊ABS Altitude Barometric Switch 高度（海拔)气压开关ABS Anti—Lock Brake System 防锁刹车系统,防抱刹车系统,反锁定刹车系统ABS American Bureau of Standards 美国标准局Abs Absolute 绝对的ABS Visc Absolute Viscosity绝对粘度ABSV Air Bypass Solenoid Valve空气旁通电磁阀ABV ＊Anti Backfire Valve *Air Bypass Valve ＊防止逆火阀＊空气旁通阀ABV Air Bypass Valve 空气旁通阀ABV Anti-Backfire Valve 防回火阀AC Air Condition 空调AC Alternating Current Generator 交流发电机AC *Alternating Current ＊After Contro *交流电*后段调整式AC AC Auxiliary Fan Relay空调辅助风扇继电器AC AC Compressor Safety Switch空调压缩机安全开关AC AC Condenser Blower Motor Relay空调冷凝器鼓风马达继电器AC AC Control Unit 空调电脑盒AC AC Diode空调二极管AC AC Evaporator Motor Relay空调蒸发马达继电器AC AC Evaporator Pump Line Fuse空调蒸发泵保险丝AC AC High Pressure Safety Switch空调高压安全开关AC AC Idle Boost Valve 空调怠速加压阀AC Alternating Current 交流电AC Ante Christum 公元前AC Accumulator 蓄电池,储压器AC Acid酸AC Analogue Computer模拟计算机AC Automatic Control 自动控制AC Air—Cooled 空冷AC Armored Car 装甲汽车AC Adaptive Control自适应调节AC Aerodynamic Center 空气动力中心AC Air Cooling 风冷,空气冷却，气冷AC Air Cycle 空气循环AC Automatic Clutch自动离合器ACC A/C Clutch Compressor 空调压缩机ACC Air Conditioning Clutch 空调离合器ACC Air Conditioning Clutch Switch空调离合器开关ACC Automatic Climate Control电脑恒温控制ACC *Accessary ＊Altitude Compensation Carb *附件*高度补偿化油器Accel Accelerator 油门，加速踏板，加速泵ACCS A/C Clutch Cycling Switch 空调离合器循环开关ACCS Air Conditoning Cycling Switch 空调循环开关Accum Accumulator 蓄压器ACCWM Air Cleaner Cold Weather Modulator 空气滤清器低温调节器Accy Accessory 附件ACD Auxiliary Control Device 辅助控制装置ACD Air Conditioning Demand 空调作用指令ACD Air Conditioning Demand Switch 空调需求开关ACDV Air Cleaner Diverter Valve 空气滤清器分流阀ACE Air Conditioning Equipment空气调节设备ACE Automatic Check Equipment 自动检测设备ACE Automatic Computing Equipment 自动计算装置ACE Air Conditioning Equipment 空调设备ACG Alternating Current Generator交流发电机ACG Automatic Control Gear自动控制变速ACID TEST CYC—LE Acceleration，Cruise, Idle，Deceleration Test Cycle加速.稳速。
贝利莫 Butterfly 阀门 F6300L 技术数据表说明书
F6300LButterfly Valve with Lug types• Disc 304 stainless steel • Bubble tight shut-off • Resilient seat• Valve face-to-face dimensions comply with API 609 & MSS-SP-67• Completely assembled and tested, ready for installationType overviewType DN F6300L300Technical dataFunctional dataValve size [mm]12" [300]Fluidchilled or hot water, up to 60% glycol Fluid Temp Range (water)-22...250°F [-30...120°C]Body Pressure Rating ANSI Class Consistent with 125, 232 psi CWP Close-off pressure ∆ps 200 psiFlow characteristic modified equal percentage Servicing maintenance-free Flow Pattern 2-way Leakage rate0%Controllable flow range 90° rotation Cv8250 Maximum Velocity 12 FPS Lug threads7/8-9 UNCMaterialsValve body Ductile cast iron ASTM A536Body finish polyester powder coated Stem 420 stainless steel SeatEPDMPipe connection for use with ANSI class 125/150 flanges Bearing Steel, PTFE, Bronze Disc304 stainless steel Gear operator materialsGears - hardened steel Suitable actuatorsNon-Spring PRB(X)Electrical fail-safePKRB(X)F6300L Product featuresFlow/Mounting detailsDimensionsType DN WeightF6300L30091 lb [41 kg]Valve with PRB(X) ActuatorA B C D E F Number of Bolt Holes12.0" [304] 3.1" [78]29.7" [754]20.4" [517]9.2" [234]9.2" [234]12F6300LValve with PKR ActuatorA B C D E F Number of Bolt Holes12.0" [304] 3.2" [82]31.9" [810]22.8" [578]9.2" [234]9.2" [234]12PRBUP-3-TOn/Off, Floating point, Non fail-safe, 24...240 VTechnical dataElectrical data Nominal voltage AC 24...240 V / DC 24...125 VNominal voltage frequency50/60 HzRemark about nominal voltage range AC 19.2...264 V / DC 19.2...137.5 VPower consumption in operation20 WPower consumption in rest position7 WTransformer sizing with 24 V 20 VA / with 240 V 52 VAAuxiliary switch2x SPDT, 1 mA...3 A (0.5 A inductive), DC 5 V...AC250 V (II, reinforced insulation), 1x 10° / 1x0...90° (default setting 85°)Switching capacity auxiliary switch 1 mA...3 A (0.5 A inductive), DC 5 V...AC 250 V(II, reinforced insulation)Electrical Connection Terminal blocks, (PE) Ground-ScrewOverload Protection electronic thoughout 0...90° rotationFunctional data Direction of motion motor reversible with appManual override7 mm hex crank, suppliedAngle of rotation90°Running Time (Motor)35 s / 90°Noise level, motor68 dB(A)Position indication integral pointerSafety data Power source UL Class 2 SupplyDegree of protection IEC/EN IP66/67Degree of protection NEMA/UL NEMA 4XEnclosure UL Enclosure Type 4XAgency Listing cULus acc. to UL60730-1A/-2-14, CAN/CSAE60730-1:02, CE acc. to 2014/30/EU and2014/35/EUQuality Standard ISO 9001Ambient humidity Max. 100% RHAmbient temperature-22...122°F [-30...50°C]Servicing maintenance-freeWeight Weight 6.8 lb [3.1 kg]Materials Housing material Die cast aluminium and plastic casingPRBUP-3-TApplicationOperationProduct featuresPR Series valve actuators are designed with an integrated linkage and visual position indicators. For outdoor applications, the installed valve must be mounted with the actuator at or above horizontal. For indoor applications the actuator can be in any location including directly under the valve.The PR series actuator provides 90° of rotation and a visual indicator shows the position of the valve. The PR Series actuator uses a low power consumption brushless DC motor and is electronically protected against overload. A universal power supply is furnished to connect supply voltage in the range of AC 24...240 V and DC 24...125 V. Included is a smart heater with thermostat to eliminate condensation. Two auxiliary switches are provided; one set at 10° open and the other is field adjustable. Running time is field adjustable from 30...120 seconds by using the Near Field Communication (NFC) app and a smart phone.†Use 60°C/75°C copper wire size range 12...28 AWG, stranded or solid. Use flexible metal conduit. Push the listed conduit fitting device over the actuator’s cable to butt against the enclosure. Screw in conduit connector. Jacket the actuators input wiring with listed flexible conduit. Properly terminate the conduit in a suitable junction box. Rated impulse Voltage 4000 V. Type of action 1. Control pollution degree 3.AccessoriesMechanical accessoriesDescriptionType Hand crank for PR, PKR, PMZG-HND PRElectrical installationMeets cULus requirements without the need of an electrical ground connection.Universal Power Supply (UP) models can be supplied with 24 VAC up to 240 VAC, or 24 VDC upto 125 VDC.Disconnect power.Provide overload protection and disconnect as required.Two built-in auxiliary switches (2x SPDT), for end position indication, interlock control, fanstartup, etc.Actuators may be controlled in parallel. Current draw and input impedance must be observed.Warning! Live electrical components!During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury.Wiring diagramsOn/OffPRBUP-3-T Wiring diagramsOn/OffFloating PointAuxiliary SwitchesElectrical installationPRBUP-3-T Dimensions。
美国电钻公司Eaton的199122号目录中的Moeller系列快速连接反转启动器说明书
Eaton 199122Eaton Moeller® series Rapid Link - Reversing starter, 6.6 A,Sensor input 4, Actuator output 2, 180/207 V DC, Ethernet IP, HAN Q4/2, with manual override switchEaton Moeller® series Rapid Link Reversing starter199122RAMO5-W421EIP-412RS14015081971800120 mm 270 mm 220 mm 1.83 kgUL approval UL 60947-4-2 RoHSIEC/EN 60947-4-2 CE CCCAssigned motor rating: for normal internally and externally ventilated 4 pole, three-phase asynchronous motors with 1500 rpm at 50 Hz or 1800 min at 60 HzProduct NameCatalog Number Model CodeEANProduct Length/Depth Product Height Product Width Product Weight Certifications Catalog NotesIs the panel builder's responsibility. The specifications for the switchgear must be observed.3 kW6.6 A (at 150 % Overload)480 V AC, 3-phase400 V AC, 3-phase10000 A0 VMeets the product standard's requirements.Is the panel builder's responsibility. The specifications for the switchgear must be observed.Does not apply, since the entire switchgear needs to be evaluated.0 kW2.238 kWMeets the product standard's requirements.0 V-40 °CTwo sensor inputs through M12 sockets (max. 150 mA) for quick stop and interlocked manual operation2 Actuator outputsKey switch position OFF/RESET ETN.RAMO5-W421EIP-412RS1.edzramo5_v14.dwgramo5_v14.stpeaton-bus-adapter-rapidlink-speed-controller-dimensions-002.eps eaton-bus-adapter-rapidlink-speed-controller-dimensions-003.eps eaton-bus-adapter-rapidlink-reversing-starter-dimensions-003.eps eaton-bus-adapter-rapidlink-reversing-starter-dimensions-002.epsRapid Link 5 - brochureDA-SW-drivesConnect - installation helpDA-SW-Driver DX-CBL-PC-3M0DA-SW-drivesConnectDA-SW-USB Driver DX-COM-STICK3-KITDA-SW-USB Driver PC Cable DX-CBL-PC-1M5DA-SW-drivesConnect - InstallationshilfeMaterial handling applications - airports, warehouses and intra-logisticsIL034092ZUGeneration Change RASP4 to RASP5Generation change from RA-SP to RASP 4.0Generation Change RA-SP to RASP5Generation change from RA-MO to RAMO 4.0Configuration to Rockwell PLC for Rapid LinkGeneration change RAMO4 to RAMO5DA-DC-00004525.pdfDA-DC-00003964.pdfDA-DC-00004184.pdfDA-DC-00004523.pdf10.11 Short-circuit ratingRated operational power at AC-3, 380/400 V, 50 HzInput currentRated operational voltageRated conditional short-circuit current, type 1, 480 Y/277 V Rated control supply voltage (Us) at AC, 50 Hz - min10.4 Clearances and creepage distances10.12 Electromagnetic compatibility10.2.5 LiftingRated power at 575 V, 60 Hz, 3-phaseRated power at 460 V, 60 Hz, 3-phase10.2.3.1 Verification of thermal stability of enclosures Rated control supply voltage (Us) at DC - minAmbient storage temperature - minFitted with:eCAD model mCAD model,Manual override switchKey switch position AUTOThermistor monitoring PTCKey switch position HANDThermo-clickElectronic motor protectionShort-circuit releaseOverload cycleAC-53aNumber of pilot lightsRated control supply voltage (Us) at AC, 50 Hz - max0 VSystem configuration typePhase-earthed AC supply systems are not permitted.AC voltageCenter-point earthed star network (TN-S network)10.8 Connections for external conductorsIs the panel builder's responsibility.Coordination class (IEC 60947-4-3)Class 1Rated conditional short-circuit current, type 1, 600 Y/347 V0 ARated conditional short-circuit current (Iq)10 kABraking voltage180/215 V DC -15 % / +10 %, Actuator for external motor brakeAmbient operating temperature - max55 °CRated operational power at AC-3, 220/230 V, 50 Hz0 kWClimatic proofing< 95 %, no condensationIn accordance with IEC/EN 50178FeaturesParameterization: drivesConnectParameterization: drivesConnect mobile (App) Parameterization: KeypadParameterization: FieldbusLifespan, electrical10,000,000 Operations (at AC-3)Number of command positions2Electrical connection type of main circuitPlug-in connectionElectrical connection type for auxiliary- and control-current circuit Plug-in connectionRated control supply voltage (Us) at DC - max0 V10.9.3 Impulse withstand voltageIs the panel builder's responsibility.Braking current≤ 0.6 A (max. 6 A for 120 ms), Actuator for external motor brakeAmbient operating temperature - min-10 °C10.6 Incorporation of switching devices and componentsDoes not apply, since the entire switchgear needs to be evaluated.Current limitation0.3 - 6.6 A, motor, main circuitAdjustable, motor, main circuitCable length10 m, Radio interference level, maximum motor cable length10.5 Protection against electric shockDoes not apply, since the entire switchgear needs to be evaluated.Mounting positionVerticalMains switch-on frequencyMaximum of one time every 60 secondsClassCLASS 10 A10.13 Mechanical functionThe device meets the requirements, provided the information in the instruction leaflet (IL) is observed.10.2.6 Mechanical impactDoes not apply, since the entire switchgear needs to beevaluated.10.9.4 Testing of enclosures made of insulating materialIs the panel builder's responsibility.10.3 Degree of protection of assembliesDoes not apply, since the entire switchgear needs to be evaluated.Electromagnetic compatibilityClass AVoltage typeDCProduct categoryMotor starterOverload release current setting - min0.3 ARated control voltage (Uc)24 V DC (-15 %/+20 %, external via AS-Interface® plug)180/207 V DC (external brake 50/60 Hz)Rated operational current (Ie)6.6 AAssigned motor power at 460/480 V, 60 Hz, 3-phase3 HPRated frequency - min47 HzNumber of auxiliary contacts (normally closed contacts)Rated conditional short-circuit current (Iq), type 2, 380 V, 400 V, 415 V0 APower consumption8 W10.2.3.2 Verification of resistance of insulating materials to normal heatMeets the product standard's requirements.10.2.3.3 Resist. of insul. mat. to abnormal heat/fire by internal elect. effectsMeets the product standard's requirements.On-delay20 - 35 msLifespan, mechanical10,000,000 Operations (at AC-3)Rated operational current (Ie) at 150% overload6.6 AProtocolEtherNet/IPOverload release current setting - max6.6 A10.9.2 Power-frequency electric strengthIs the panel builder's responsibility.Overvoltage categoryIIIDegree of protectionNEMA 12IP65Rated frequency - max63 HzVibrationResistance: 10 - 150 Hz, Oscillation frequency Resistance: 57 Hz, Amplitude transition frequency on accelerationResistance: 6 Hz, Amplitude 0.15 mmResistance: According to IEC/EN 60068-2-6Rated operational power at 380/400 V, 50 Hz - max3 kWAmbient storage temperature - max70 °CShort-circuit protection (external output circuits)Type 1 coordination via the power bus' feeder unit, Main circuitRated control supply voltage (Us) at AC, 60 Hz - min0 V10.7 Internal electrical circuits and connectionsIs the panel builder's responsibility.Rated impulse withstand voltage (Uimp)4000 VConnectionConnections pluggable in power sectionOff-delay20 - 35 ms10.10 Temperature riseThe panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.FunctionsFor actuation of motors with mechanical brakeExternal reset possibleTemperature compensated overload protectionOutput frequency50/60 HzMains voltage tolerance380 - 480 V (-15 %/+10 %, at 50/60 Hz)Rated conditional short-circuit current (Iq), type 2, 230 V0 ATypeReversing starter10.2.2 Corrosion resistanceMeets the product standard's requirements.Supply frequency50/60 Hz, fLN, Main circuit10.2.4 Resistance to ultra-violet (UV) radiationMeets the product standard's requirements.10.2.7 InscriptionsMeets the product standard's requirements.Rated control supply voltage (Us) at AC, 60 Hz - max0 VRated operational current (Ie) at AC-3, 380 V, 400 V, 415 V6.6 ARated operational power at 380/400 V, 50 Hz - min0.09 kWModelReversing starterNumber of auxiliary contacts (normally open contacts)2Shock resistance15 g, Mechanical, According to IEC/EN 60068-2-27, 11 ms, Half-sinusoidal shock 11 ms, 1000 shocks per shaftAltitudeEaton Corporation plc Eaton House30 Pembroke Road Dublin 4, Ireland © 2023 Eaton. All Rights Reserved. Eaton is a registered trademark.All other trademarks areproperty of their respectiveowners./socialmediaMax. 2000 mMax. 1000 mAbove 1000 m with 1 % performance reduction per 100 m。
Wilkerson Corp. 9EM-TK-190-5 B 螺絮、调节器、润滑器肺道肺部分商品说明
B196Catalog 9EM-TK-190-5Pneumatic Division Richland, Michigan Basic 1/2" BodytubingBowl removalclearanceSpecificationsFlow Capacity* 3/8 200 SCFM (94 dm 3/s, ANR)1/2 200 SCFM (94 dm 3/s, ANR) 3/4 235 SCFM (109 dm 3/s, ANR)Adjusting Range Pressure 0 to 30 PSIG (0 to 2.1 bar) 0 to 60 PSIG (0 to 4.1 bar) 0 to 125 PSIG (0 to 8.6 bar) 0 to 250 PSIG (0 to 17.2 bar)Gauge Port (2) NPT / BSPP-G 1/4Maximum Supply Plastic Bowl 150 PSIG (10.3 bar) Pressure Metal Bowl 250 PSIG (17.2 bar)Operating Plastic Bowl -13° to 125°F (-25° to 52°C) Temperature Metal Bowl -13° to 150°F (-25° to 65.5°C)Port Size NPT / BSPP-G 3/8, 1/2, 3/4Bowl Capacity 2.87 oz Standard Filtration 5 MicronWeight1.87 lb. (0.85 kg)* Inlet pressure 145 psig (10 bar). Secondary pressure 91.3 psig (6.3 bar) and 14.5 psig (1 bar) pressure drop .“F” Series Filters, Type “A” 5 micron elements: All Wilkerson Type “A” 5 micron elements meet or exceed ISO Class 3 for maximum particle size and concentration of solid contaminants.Air quality: Within ISO 8573-1: 1991 Class 3 (Particulates) Within ISO 8573-1: 2001 Class 6 (Particulates)Materials of ConstructionAdjustment Knob AcetalB ody AluminumBody Cap ABS Bowls Plastic Bowl Polycarbonate Metal Bowl AluminumDiaphragm Assembly Nitrile / ZincElement Retainer / Baffle AcetalFilter Element Sintered Polyethylene Panel Nut Acetal Seals Plastic Bowl Nitrile Metal Bowl NitrileSight Gauge Metal Bowl Polyamide (Nylon)Springs Main Regulating / Valve Steel / S.S.Valve Assembly Brass / NitrileFilter / Regulator B28Features• 5 Micron Filtration• Balanced Valve Design • Spring Loaded Diaphragm• 3/4" NPT / BSPP-G Over-Ported• Quick-Disconnect Bowl / Bowl Guard • Light Weight• High Flow CapacitiesCAUTION:REGULATOR PRESSURE ADJUSTMENT – The working range of knob adjustment is designed to permit outlet pressures within their full range. Pressure adjustment beyond this range is also possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting devices may be obtained only by special design.For best performance, regulated pressure should always be set by increasing the pressure up to the desired setting.WARNING Product rupture can cause serious injury.Do not connect regulator to bottled gas.Do not exceed maximum primary pressure rating.!Inches (mm)Manual DrainAutomatic Drain (Revised 05-28-2019)Catalog 9EM-TK-190-5B197Pneumatic DivisionRichland, MichiganFilter / Regulator B28Replacement Bowl KitsMetal Bowl –Sight Gauge, Automatic Drain ...............................GRP-96-645Sight Gauge, Manual Drain ....................................GRP-96-644Plastic Bowl –Bowl Guard, Automatic Drain .................................GRP-96-643Bowl Guard, Manual Drain .....................................GRP-96-642Replacement Element KitsType“ A”, 5 Micron .......................................................FRP-96-653Element, Deflector, Retainer kit ..................................FRP-96-283Replacement KitsAdjusting Knob .....................................................RRP-16-341-000Diaphragm Assembly –Non-relieving ............................................................RRP-96-987Relieving ..................................................................RRP-96-986Spring, Regulating –0 to 30 PSIG (0 to 2.1 bar) ......................................RRP-96-1630 to 60 PSIG (0 to 4.1 bar) ......................................RRP-96-1640 to 125 PSIG (0 to 8.6 bar) ....................................RRP-96-1650 to 250 PSIG (0 to 17.2 bar) ..................................RRP-96-166Valve Assembly ...........................................................RRP-96-049AccessoriesAutomatic Drain –Fluorocarbon ...........................................................GRP-95-981Nitrile .......................................................................GRP-95-973Manual Drain ............................................................. GRP-96-685Panel Mount Nut –Aluminum .................................................................RRP-96-674Plastic ......................................................................RRP-96-676Gauge, Pressure –50mm (2") round 1/4" center back mount0-30 PSIG / 0-2 bar ..........................................K4520N140300-60 PSIG / 0-4 bar ..........................................K4520N140600-160 PSIG / 0-11 bar ......................................K4520N141600-300 PSIG / 0-20 bar ......................................K4520N143000 to 160 PSIG, 1-3/4" Digital Round,1/4" NPT ............................................................K4517N14160DTamper Resistant Kit ...................................................RRP-96-672Sight Gauge Kit ..........................................................GRP-96-825Wall Mounting Bracket –L-Type (Body) ..........................................................GPA-96-605L-Type (Bonnet). ......................................................GPA-96-607T-Type ...................................................................GPA-96-602Inlet Pressure - 10 bar (145 psig)SecondaryPressure-(bar)SecondaryPressure-(psig)204060801001201402.5 bar36.3 psig8.0 bar116 psig4.0 bar58 psig6.5 bar94.3 psig23456789101103020401305010011070120809060Flow - (scfm)20406080100120140240260200220180160Flow - (dm3/s)nB28 1/2" Filter / RegulatorInlet Pressure - 10 bar (145 psig)SecondaryPressure-(bar)SecondaryPressure-(psig)204060801001201402.5 bar36.3 psig8.0 bar116 psig4.0 bar58 psig6.5 bar94.3 psig23456789101103020401305010011070120809060Flow - (scfm)20406080100120140240260200220180160Flow - (dm3/s)nB28 3/8" Filter / RegulatorInlet Pressure - 10 bar (145 psig)SecondaryPressure-(bar)SecondaryPressure-(psig)204060801001201402.5 bar36.3 psig8.0 bar116 psig4.0 bar58 psig6.5 bar94.3 psig23456789101103020401501301405010011070120809060Flow - (scfm)20406080100120140240260280300200220180160Flow - (dm3/s)nB18 3/8" Filter / Regulator(Revised 12-11-2019)。
GALILEO 用户手册说明书
2GALILEO OPENManufacturerEaton Automation AG Spinnereistrasse 8-14 CH-9008 St. Gallen Switzerland SupportRegion North America Eaton Corporation Electrical Sector 1111 Superior Ave. Cleveland, OH 44114 United States877-ETN-CARE (877-386-2273) Other regionsPlease contact your supplier or send an E-Mail to: a *******************Original instructionsThe German version of this document is the original instructionsEditorManfred HüppiBrand and product namesAll brand and product names are trademarks or registered trademarks of the owner concerned.Copyright© Eaton Automation AG, CH-9008 St. Gallen All rights reserved, also for the translation.None of this document may be reproduced or processed, duplicated or distributed by electronic systems in any form (print, photocopy, microfilm or any other process) without the written permission of Eaton Automation AG, St. Gallen. Subject to modifications.GALILEO OPEN3Imprint1General (5)2Project design with GALILEO (7)2.1Panel Type (7)2.2Select PLC (8)3Testing the GALILEO project (9)4GALILEO OPEN project structure (11)5Licensing (15)4GALILEO OPENGALILEO OPEN51GeneralGALILEO OPEN is a PC-based visualization software consisting of the GALILEO Runtime System(WinGRS).WinGRS can be run on operating systems Windows under the following versions:Operating system 32 Bit 64 BitWindows CE - -Windows XP ✓-Windows Vista ✓-Windows 7 ✓✓Tab. 1Versions of the operating systemThe project is designed with the GALILEO visualization tool.This document describes the specific settings/additions that must be made for licensing PC operationand project design.This document is designed as a reference for commissioning and operation.Information on GALILEO is provided in the GALILEO Online Help.6GALILEO OPENGALILEO OPEN72Project design with GALILEO2.1Panel TypeCreate a new project with GALILEO and call this for example «Test».The «Panel Type» window will appear.⏹Click on «Panel Selection» in the «Panel Type» window and select GALILEO OPEN.⏹Confirm the selection with «OK».⏹Define the number of colors in your project. You can choose between 256, 65,536 or 16,777,216colors.Fig. 1Panel TypeGALILEO OPEN enables you to select any screen size as required. You can create projects that takeup the entire screen or only part of it.The following resolutions match the maximally possible solution:X-Resolution: 10 – 1600 pixelsY-Resolution: 10 – 1200 pixels⏹Confirm your selection with «OK».8GALILEO OPEN2.2 Select PLC⏹ The «Select PLC» window will appear. ⏹ Click the «Add» button.Fig. 2Select PLC⏹ In the «Communication Selection» window use the «Model:» drop-down menu to choose therequired communication.Fig. 3 Select Communication⏹ Confirm your selection with «OK».⏹ Confirm your selection in the «Select PLC» window with «OK».Now create your project with GALILEO.☞ NOTE:Information on «Loading drivers» and general topics concerning project design with GALILEO, Workshop and Runtime is provided in the Online Help.GALILEO OPEN93Testing the GALILEO projectThe integrated «GALILEO Project Inspector» (GPI) enables you to test your project directly fromGALILEO.The project must be compiled beforehand and can then be started by clicking the «Start Inspector»button.Fig. 4Testing the project10GALILEO OPEN4GALILEO OPEN project structureAfter compilation, GALILEO creates a directory with all files that are required for starting the projecton a Windows PC.If, for example, a project «TEST.PRJ» is generated in the directory «D:\DATA\GALILEO\», thefollowing directory structure is produced after compiling.D:\DATA\GALILEO\TEST\test\runtimeThe directory \runtime contains the file «WinGRS.exe» which must be started on the target system.GALILEO enables you to transfer the project files via FTP, locally or to a network drive (download).Further information is provided in the GALILEO Online Help.When transferring the files to the target system, you must copy the entire directory structure.Example: TEST\test\appl\custom\data\runtimeOnce the files are on the target system, you can a) Click «WinGRS.exe»in the appropriate folder, b) create a shortcut to it on the desktop or c) enter it in the Startup folder.a) Clicking «WinGRS.exe» in the folderFig. 5Explorer – runtimeb) Creating a desktop shortcut for «WinGRS.exe»Fig. 6Explorer – runtime – generate desktop shortcutc) Entering «WinGRS.exe» in the Startup folder (see documentation for the relevant Windows operating system).5LicensingOnce you have stored the GALILEO OPEN directory structure on a PC, and started the«WinGRS.exe» runtime program, the «License Administrator 2.25.0» will appear.Fig. 7License AdministratorThe «Serial» field shows a 12-digit code. This serial code is permanently linked to the PC on whichyou have just started the runtime program.NOTE:To enter the GALILEO OPEN license code, the PC / mobile PC must be in a state inwhich it will later be run with GALILEO OPEN. The license activation may be lost everytime hardware (docking station, hard disk etc.) is added. GALILEO OPEN will then onlyrun in DEMO mode.In this case, please contact our Support:********************Proceed as follows to obtain a license for operating GALILEO OPEN:⏹Make a note of the 12-digit serial code (generated for each specific PC) displayed in the«License Administrator».⏹Contact an Eaton Automation sales representative and request a GALILEO OPEN license withthe designation «LIC-GALILEO-OPEN-PC».In order to run GALILEO OPEN on an Eaton XP device, you must order a license with the designation «LIC-GALILEO-OPEN-XP».⏹The license product paper will be sent to you by post.Fig. 8License Product Paper⏹Fill in the license product paper.⏹Fax the license product paper to the printed fax number (Support).⏹On receipt of the fax, the Support department will then generate a license number.⏹Notify Support how the license number should be sent (by post, fax or email).⏹Click «Change License».⏹Enter the license number via the displayed keyboard.Fig. 9License Administrator – Change License⏹Confirm your entry with «OK».GALILEO OPEN Runtime is now activated and can be used on the PC.。
摩力克TM（Molykote）品牌新增Lubolid产品
摩力克TM（Molykote）品牌新增Lubolid产品
佚名
【期刊名称】《《现代制造》》
【年(卷),期】2005(000)019
【摘要】2005年7月6日，为了更好地服务于全球汽车用户，道康宁公司将在其摩力克^TM（Molykote）汽车润滑产品和服务系列中新增Lubolic产品。
“将深受信赖的Lubolid品牌加入到摩力克”（Molykote）产品家族中更加证实了我们对汽车市场的承诺，我们将为汽车用户提供成套的产品和服务、综合的润滑专业技能、可信赖的产品性能和智能润滑解决方案。
”道康宁润滑产品、汽车工业销售经理石惠先生说道。
【总页数】1页(P23)
【正文语种】中文
【中图分类】F270
【相关文献】
1.道康宁推出摩力克TM（MOLYKOTE）L-8008新型润滑剂 [J],
2.优化的摩力克TM（MOLYKOTE）EM-30L润滑脂 [J],
3.优化的摩力克TM MOLYKOTE EM-30L润滑脂可用于汽车电动机械的塑料部件[J],
4.摩力克^TM（MOLYKOTE）L-8008润滑剂为滑动零件提供不粘涂层 [J],
5.摩力克^TM（MOLYKOTE）G-2003为塑料和金属组合件提供长效润滑 [J],因版权原因，仅展示原文概要，查看原文内容请购买。
摩润D-400 weed和虫子控制系统洗涤剂说明书
Morwet ® D-400A dispersant with excellent performance and less costMorwet D-400 is a result of our continuous customer focused work to improve economy for formulators and farmers while maintaining high-efficiency weed and pest control.Less robust alternatives can be used in standard formulations and Morwet D-400 fulfils these requirements with excellent and reliable performance at reduced cost.What is Morwet D-400?An alkyl naphthalene sulfonate sodium salt condensate (NSC) that is closely related to Morwet D-425.• A dispersant designed to perform in standard systems under normal conditions• EPA 40 CFR 180.920 status and same CAS number as Morwet D-425Why use Morwet D-400?• Developed to formulate dry and liquid products for highly efficient CP formulations• Effective with herbicide, fungicide and insecticide applications• Provides excellent storage properties to WG • Morwet D-400 replaces and outperforms competitor dispersant products at the same use level • Low cost alternativeMorwet D-400 is an excellent choice for standard WDG and will perform equally as Morwet D-425.In contrast to many other NSC products on the market,Morwet D-400 ensures good properties of your formulation after storage. For more complex formulations, Morwet D-425 is a safe choice.Morwet products provide superior performance at low concentrations.Typical propertiesProperty Value Activity >72.5%Appearance tan powder Flash point (PMCC)>200°F Moisture max 3%pH (5% in water)7.5-10Suspensibility after storage, 2 weeks 54°CInfluence of dispersant concentrate in an Imidacloprid 70 WG formationS u s p e n s i b i l i t y (%)7565553%6%8%607080Morwet D-400Morwet D-425Competitor NSC85S u s p e n s i b i l i t y (%)80400methyl 75 WG70 WG50 WG2060100Morwet D-400Morwet D-425Competitor NSC2Nouryon is a global, specialty chemicals leader. Markets and consumers worldwide rely on our essential solutions to manufacture everyday products, such as personal care, cleaning goods, paints and coatings, agriculture and food, pharmaceuticals, and building products. Furthermore, the dedication of more than 7,900 employees with a shared commitment to our customers, business growth, safety, sustainability and innovation has resulted in a consistentlystrong financial performance. We operate in over 80 countries around the world with a portfolio of industry-leading brands. Visit our website and follow us @Nouryon and on LinkedIn.All information concerning our products and/or all suggestions for handling and use contained herein (including formulation and toxicity information) are offered in good faith and are believed to be reliable. However, Nouryon makes no warranty express or implied (i) as to the accuracy or sufficiency of such information and/or suggestions, (ii) as to any product’s merchantability or fitness for a particular use or (iii) that any suggested use (including use in any formulation) will not infringe any patent. Nothing contained herein shall be construed as granting or extending any license under any patent. The user must determine for itself by preliminary tests or otherwise the suitability of any product and of any information contained herein (including but not limited to formulation and toxicity information) for the user’s purpose. The safety of any formulations described herein has not been established. The suitability and safety of a formulation should be confirmed in all respects by the user prior to use. The information contained herein supersedes all previously issued bulletins on the subject matter covered.Products mentioned are trademarks of Nouryon and registered in many countries.M a r c h 2022Contact us directly for detailed product information and sample requestwebsite | /markets/agriculture email|****************Formulation guideTribenuron Methyl 75 WG IngredientFunction Conc, %Tribenuron methyl (95%)Herbicide 79Morwet D-400Dispersant 8Berol 790AWetting agent 2Light Calcium CarbonateFillerq.s.Imidacloprid 70 WG Ingredient Function Conc, %Imidacloprid (96%)Insecticide 73Morwet D-400Dispersant 3Morwet EFW Wetting agent 3Agrilan 700Co-Dispersant 2Ultrazine NA Binder 7Corn starchFillerq.s.Tebuconazole 250 g/L SC IngredientFunction Conc, %Tebuconazole (97%)Fungicide 25.00Morwet D-400Dispersant 2.50Siloxane oil Antifoam0.20Xanthan gum Rheology modifier 0.35Propylene glycolAntifreeze 5.00WaterFillerq.s.Azoxystrobin 250 g/L SC Ingredient Function Conc, %Azoxystrobin (96%)Fungicide 25.00Morwet D-400Dispersant2.50Ethylan NS-500 LQ Wetting/Co-dispersant 1.00Siloxane oil Antifoam0.20Xanthan gum Rheology modifier 0.35Propylene glycol Antifreeze 5.00WaterFillerq.s.。
摩克斯 SDS-3008 系列产品名称和型号说明书
SDS-3008SeriesIndustrial 8-port smart EthernetswitchesFeatures and Benefits•Compact and flexible housing design to fit into confined spaces •Web-based GUI for easy device configuration and management•EtherNet/IP,PROFINET,and Modbus TCP industrial protocols supported foreasy integration and monitoring in automation HMI/SCADA systems•Multi-language web GUI:English,Traditional Chinese,Simplified Chinese,Japanese,German,and French•Supports RSTP/STP for network redundancy •Security features based on IEC 62443CertificationsIntroductionThe SDS-3008smart Ethernet switch is the ideal product for IA engineers and automation machine builders to make their networks compatible with the vision of Industry 4.0.By breathing life into machines and control cabinets,the smart switch simplifies daily tasks with its easy configuration and easy installation.In addition,it is monitorable and is easy to maintain throughout the entire product life cycle.The most frequently used automation protocols—including EtherNet/IP,PROFINET,and Modbus TCP—are embedded in the SDS-3008switch to provide enhanced operational performance and flexibility by making it controllable and visible from automation HMIs.It also supports a range of useful management functions,including IEEE 802.1Q VLAN,port mirroring,SNMP,warning by relay,and a multi-language Web GUI.Additional Features and Benefits•Supports IEEE 802.1D-2004and IEEE 802.1w STP/RSTP for rapid network redundancy•IEEE 802.1Q VLAN to ease network planning•Supports the ABC-02-USB automatic backup configurator for quick event log and configuration backup.Can also enable quick device switch over and firmware upgrade•Automatic warning by exception through relay output•Unused port lock,SNMPv3and HTTPS to enhance network security •Role-based account management for self-defined administration and/or user accounts•Local log and the ability to export inventory files ease inventory managementSpecificationsInput/Output InterfaceAlarm Contact Channels 1,Relay output with current carrying capacity of 1A @24VDC ButtonsReset button Digital Input Channels 1Digital Inputs+13to +30V for state 1-30to +3V for state 0Max.input current:8mAEthernet Interface10/100BaseT(X)Ports(RJ45connector)8Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connectionStandards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)IEEE802.3x for flow controlIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1Q for VLAN TaggingEthernet Software FeaturesIndustrial Protocols EtherNet/IP,Modbus TCP,PROFINET IO Device(Slave)Management Back Pressure Flow Control,DHCP Client,Flow control,IPv4/IPv6,LLDP,Port Mirror,SNMP Inform,SNMPv1/v2c/v3,SyslogMIB RFC1213,Ethernet-like MIB,IF MIB,LLDP MIB,Bridge MIB,Q-BRIDGE MIB Redundancy Protocols RSTP,STPSecurity Broadcast storm protection,HTTPS/SSL,SNMPv3,Port LockTime Management NTP Server/Client,SNTPFilter802.1Q VLANSwitch PropertiesMAC Table Size8KMax.No.of VLANs8VLAN ID Range VID1to4094Packet Buffer Size3MbitsUSB InterfaceStorage Port USB Type ALED InterfaceLED Indicators PWR1,PWR2,STATE,FAULT,10/100M(TP Port)Power ParametersConnection2removable4-contact terminal block(s)Input Voltage12/24/48/-48VDC,Redundant dual inputsOperating Voltage9.6to60VDCInput Current0.55A@24VDCOverload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsHousing MetalIP Rating IP40Dimensions20x135x111mm(0.79x5.32x4.37in)Weight438g(0.97lb)Installation DIN-rail mountingEnvironmental LimitsOperating Temperature SDS-3008:-10to60°C(14to140°F)SDS-3008-T:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsEMC EN61000-6-2/-6-4EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:2kV;Signal:2kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFSafety EN60950-1(LVD),UL61010-2-201,UL508Shock IEC60068-2-27Freefall IEC60068-2-32Vibration IEC60068-2-6MTBFTime1,391,620hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x SDS-3008Series switchInstallation Kit4x cap,plastic,for RJ45portDocumentation1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified Chinese1x quick installation guide1x warranty cardDimensionsOrdering InformationModel Name Layer Total No.of Ports 10/100BaseT(X)PortsRJ45ConnectorOperating Temp.SDS-3008288-10to60°CSDS-3008-T288-40to75°C Accessories(sold separately)Storage KitsABC-02-USB Configuration backup and restoration tool,firmware upgrade,and log file storage tool for managedEthernet switches and routers,0to60°C operating temperatureABC-02-USB-T Configuration backup and restoration tool,firmware upgrade,and log file storage tool for managedEthernet switches and routers,-40to75°C operating temperaturePower SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureRack-Mounting KitsRK-4U19-inch rack-mounting kit©Moxa Inc.All rights reserved.Updated Nov12,2018.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
道康宁Dow Corning
道康宁Dow Corning美国道康宁公司（DOW CORNING）是美国道化学公司（陶氏化学）和美国康宁公司的子公司，是世界上有机硅和固体润滑技术最具权威的特大型跨国公司，其生产的特种润滑剂及密封剂，系列齐全，满足电子、机械、汽车、飞机、冶金、石油化工、电力、制药、建筑机械、建材、纺织、塑料制品、食品等众多特种润滑和密封要求，无论环境多恶劣，条件多极端，都必定有一种道康宁（DOW CORNING）的摩力克（MOLYKOTE）特种润滑剂或矽利康（SILICONE）密封剂能符合您的需求。
道康宁中国区珠海顺益道康有机硅胶，道康宁高温链条油，道康宁齿轮润滑油、轴承油，道康宁食品级润滑油，降解液压油236分散剂730耐溶剂密封剂732多用途密封剂733玻璃及合属密封剂734可流动密封剂735耐油密封剂736耐高温密封剂737中性固化密封剂739塑料粘接密封748无腐蚀密封剂剂786防霉密封剂832多种表面粘接密封剂1890保护涂层道康宁润滑剂系列:道康宁MOLYKOTE EM系列主要有:道康宁EM-10L、EM-30L、EM-40L、EM-50L、EM-60L、EM-70L及EM-D110等。
道康宁MOLYKOTE PG系列主要有:道康宁PG-21、PG-30L、PG-54、PG-65、PG-75、PG-602、PG-641、PG-662、PG-663、PG-671等。
道康宁MOLYKOTE YM系列主要有:道康宁YM-102、YM-103等。
道康宁MOLYKOTE G系列主要有:道康宁G-68、G-72、G-85、G-4500、G-4700等。
道康宁MOLYKOTE HP系列主要有:道康宁HP300,HP500,HP870,HP800等。
道康宁MOLYKOTE PD系列主要有:道康宁PD900,PD910,PD920等。
道康宁油膏：道康宁HSC PLUS、P37、P1000、DX、P40润滑脂：道康宁LONGTERM W2、1122、G68、PG75、PG54、55M、41道康宁摩力克EM系列：道康宁EM-10L、EM-30L、EM-50LEM-60L、EM-70L道康宁摩力克YM系列：道康宁YM-102、YM-103道康宁摩力克PG系列：PG-661、PG-662、PG-663道康宁摩力克HP系列：道康宁HP-300、HP-500、HP-870道康宁摩力克PD系列：道康宁PD-900、PD-910、PD-930道康宁摩力克复合膏：道康宁DOWCORNING111、DOWCORNING4、DOWCORNING7道康宁摩力克减磨涂层：道康宁D321R。
摩力克EM-30L（英文）
摩⼒克EM-30L（英⽂）Product InformationHighPerformanceGrease Molykote? EM-30L GreaseCan be used for plastic-plastic contact, metal-metal contact andplastic-metal contactLong service lifeLow seepage, so it can be used in places wherein cleanliness isrequiredDoes not contain silicone thereby preventing problems with contact point failures COMPOSITIONPoly-±-olefinLithium soapPTFE, etc. Lubricating grease developed for plastic components APPLICATIONSAutomobiles, electrical appliances, precision equipment, audio equipment, and office equipment that have plastic parts. TYPICAL PROPERTIESSpecification Writers: These values are not intended for use in preparing specifications. Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.Test*Property Unit ResultAppearance WhiteBase oil viscosity at 40oC mm2/s 90JIS K 2220 Penetration (worked 60 times) 325NLGI class 1Service temperature range ?C-45 to 150Density g/cm30.91JIS K 2220 Drop point ?C195JIS K 2220 Bleed (100oC24 hours) % 5.0JIS K 2220 Evaporation (99oC22 hours) % 0.4JIS K 2220 Oxidation resistance (99oC100 hours) MPa 0.02JIS K 2220 Copper corrosion (100oC 24 hours) 1AASTM D 2596 Four ball weld load (1500rpm/1minute) N 3730ASTM D 2266 Four ball wear scar(1200rpm, 392N, 1 hour) mm 0.5JIS K 2220 Low temperature torque test (-40oC)Starting torque mNm 110Running torque mNm 51*JIS: Japanese Industrial Standard.ASTM: American Society for Testing and Materials.HOW TO USEClean points of application.As is usual with lubricating greases,apply or fill by means of a brush,spatula, or automatic lubricationdevice.HANDLING PRECAUTIONSThis product may irritate the skin oreyes. Wear safety equipment asnecessary when handling this product.In the event of contact with skin oreyes, immediately rinse thoroughlywith water and seek medical care ifnecessary. Wash hands thoroughlyafter handling. At high temperatures inexcess of 250oC, the breakdown offluorinated polymer can cause therelease of a small amount of toxic gas.Ensure adequate ventilation.Molykote ? EM-30L Grease Dow Corning and Molykote are registered trademarks of Dow Corning Corporation. 2011, May 25We help you invent the future is a trademark of Dow Corning Corporation.Form No. 80-3106B-012002, 2006, 2011 Dow Corning Corporation. All rights reserved.2USABLE LIFE AND STORAGEWhen stored, unopened in a cool, dark place Molykote ? EM-30L Grease, has a usable life of 36 months from the date of production.PACKAGING INFORMATIONThis product is available in 1kg cans (10 cans/case) and 16kg pails.LIMITATIONSThis product is neither tested nor represented as suitable for medical or pharmaceutical uses.HEALTH ANDENVIRONMENTAL INFORMATIONTo support Customers in theirproduct safety needs, Dow Corning has an extensive ProductStewardship organization and a team of Product Safety andRegulatory Compliance (PS&RC) specialists available in each area. For further information, please see our Web site, /doc/0518067985.htmlor consult your local Dow Corning representative.LIMITED WARRANTY INFORMATION – PLEASE READ CAREFULLYThe information contained herein is offered in good faith and isbelieved to be accurate. However, because conditions and methods of use of our products are beyond our control, this information should not be used in substitution forcustomer’s tests to ensure that our products are safe, effective, and fully satisfactory for the intended end use. Suggestions of use shall not be taken as inducements to infringe any patent.Dow Corning’s sole warranty is that our products will meet the sales specifications in effect at the time of shipment.Your exclusive remedy for breach of such warranty is limited to refund of purchase price orreplacement of any product shown to be other than as warranted. DOW CORNINGSPECIFICALLY DISCLAIMS ANY OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR APARTICULAR PURPOSE OR MERCHANTABILITY. DOW CORNING DISCLAIMS LIABILITY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. We help you invent the future. ? /doc/0518067985.html。
摩力克EM-30l润滑脂应用参数
摩力克EM-30L 润滑脂应用参数
品牌；摩力克molykote
型号；EM-30L 润滑脂
经销；铭翔润滑油
类型；高性能塑料用润滑脂
应用；家用电器和办公设备中的套管、齿轮、开关、滑动导轨
．与多种塑料相容
应用方法；清洁轴承表面，按一般方法用刷子、注脂枪或自动润滑系统加脂，也可用于集中润滑系统。
对于不同的塑料部件，应在使用前做相容性试验 性能； ．可承受高压
．低氧化性，可长效润滑
．摩擦系数低
物理／化学数据
外观 白色
基础油 PAO 、锂皂、固体润滑剂
基础油粘度(40ºC)CST 90
固体润滑剂 PTFE
增稠剂 锂皂
锥入度，0.1mm 325
稠度，NLGI 级 1
工作温度，ºC -45~150
密度，g/ml 0.91
离油度(100º,24h),% 5
蒸发量，(99º,22h),% 0.4
滴点,ºC 195
钢板腐蚀(100ºC,时间) 1a
四球试验，摩耗mm （120rpm, 40 kg 1 min ）
0.5
四球，焊联载荷kg(1500rpm,1min) 380
酸化安定度kgf/cm 2, 低温转矩40ºC 0.2
启动转矩，Nm×10-4 1100
运动转矩，Nm×10-4 520。
海外品牌水泵产品说明书
PETROL POWERED WATER MOVERModel Numbers:G8016 Honda Recoil Start G8016E Honda Electric Start G8027/SIC Yanmar Recoil Start G8027E/SIC Yanmar Electric StartP R O D U C TD E S C R I P T I O NRugged, economical open impeller self priming pumps. These units are driven by either Honda overhead valve GX200 petrol engines or L70diesel engines.A P P L I C AT I O N S•Septic tank pump-out •Tank filling •Irrigation•Garden watering •Water transfer •DewateringO P E R AT I N G L I M I T S PUMPCorrosion resistant marine grade aluminium casing, suction and discharge port for longer life.Heavy duty cast iron open impeller & diffuser to extend pump life when pumping dirty water with some solids content.Nitrile rubber seal and casing orings for improved reliability in varying water quality.Mechanical shaft seal for long life.Diesel models are equipped with special hard faced SICxSIC seals for extra long life with dirty water.Able to self prime from 6m*, for improved versatility.Includes powdercoated steel roll frame with anti-vibration mounting for easy transport.*At 3600rpm, priming may be reduced at lower speeds.ENGINEPetrolHigh quality Honda GX200 petrol engine, which has European Community and USA EPA and CARB environmental standards compliance.Two stage air cleaner and cast iron sleeved cylinder bore for long engine life.Low oil protection for operator peace of mind.DieselHigh quality Yanmar L70 diesel engine, selected for a broad range of environments and altitudes to ensure ample engine reserves for most applications.Starting OptionsBoth engine options are available with recoil starters or with electric start with recoil start back-up.Note: Battery & leads not included.Maximum flow to 1000 lpmMaximum total head 32m Maximum suction lift 7m Maximum water temperature 50o C Minimum water temperature1o C Minimum suction pipe size 3”Inlet size 3”BSP(M)Outlet size3”BSP(M)SELF PRIMING PUMPSF E AT U R E S & B E N E F I T SH /O & M F G S C O R E S B YT E C H N I C A L S P E C I F I C A T I O N SH Y D R A U L I C P E R F O R M A N C EM AT E R I A L S O F C O N S T R U C T I O NPA R TM AT E R I A L Suction cover Diffuser ImpellerYoke & casing Discharge Casing bolts Yoke bolts Flap valve Seal ringCasing o-ring Mechanical seal Petrol models Diesel modelsAluminium Cast iron Cast iron Aluminium AluminiumZinc plated steel Stainless steel Nitrile rubber Nitrile rubber Nitrile rubberCarbon ceramicSilicon carbide x silicon carbideE N G I N E S P E C IF I C AT I O N SI N S TA L L AT I O N & P R I M I N GPump Model G8016G8027Engine Brand Honda Yanmar Engine Model GX200L70AE Engine TypePetrol Diesel Displacement (cc)196296Fuel Tank (litres) 3.6 3.5Oil Capacity (litres)0.6 1.1Compression Ratio 8.5:119.5:1Air Filter TypeDual-Foam/Dry Paper ElementSpark ArrestorNOApprox. fuel consumption@ full load @ 3600rpm 2.05 l/hr1.6 l/hr dB(A) @ 7m @ 3600rpm@ full load7980.5•Fit strainer to bottom of suction pipe; a foot valve is not required.•To prime, fill pump body with water then allow pump to run until drawing water.TOTAL HEAD 30201002004006008001000m FLOW (lpm)G8016 - Honda GX200G8027 - Yanmar L70D I ME N S I O N SAll dimensions in mm unless otherwise stated. Above illustration is indicative only for the diesel powered model. Add 1kg for Electric Start engine option.Model A B C D E Weight (kg)G801651041043018017031.0G802759543555022017044.0Davey Water Products Pty LtdMember of the GUD GroupABN 18 066 327 517Head Office and Manufacturing 6 Lakeview Drive,Scoresby, Australia 3179Ph:+61 3 9730 9222Fax:+61 3 9753 4100Website:.auCustomer Service Centre Ph:1300 367 866Fax:1300 369 119E-mail:***************.au Interstate OfficesSydney • Brisbane • Adelaide Perth • TownsvilleInternational 6 Lakeview Drive,Scoresby, Australia 3179Ph:+61 3 9730 9121Fax:+61 3 9753 4248E-mail:****************.au GermanyKantstrasse 53,04275 Leipzig Ph:+49 341 301 0412Fax:+49 341 301 0413E-mail:**********************New Zealand 7 Rothwell Avenue,Penrose, Auckland 1330Ph:+64 9 570 9135Fax:+64 9 527 7654Website:E-mail:****************.nz USA - Davey Pumps Inc.1005 N. Commons Drive Aurora, Illinois 60504Ph:+1 630 898 6976Fax:+1 630 851 7744Website:E-mail:******************This literature is not a complete guide to product usage. Further information is available from your Davey dealer, Davey Customer Service Centre and from the relevant product Installation and Operating Instructions. This data sheet must be read in conjunction with the relevant product Installation and Operating Instructions and all applicable statutory requirements. Product specifications may change without notice.® Davey is a registered trademark of Davey Water Products Pty Ltd. © Davey Water Products Pty Ltd 2000.DPM123-4/3K/0308/SC supersedes DPM123-3/3K/0207/SC。
Pur–A–Lyzer Mega 膜过滤袋系列说明书
Pur–A–Lyzer™Mega Dialysis KitManualPURG10010PURG10015PURG10020PURG12010PURG12015PURG12020PURG35010PURG35015PURG35020PURG60010PURG60015PURG60020 Product DescriptionPur–A–Lyzer kits may be used for:• Dialysis or buffer exchange• Sample concentration by evaporation• Protein/precipitation• Nucleic acid concentrationMega tube capacity: 3–20 mLMega Pur–A–Lyzer Kit ContentsPURG10010 1 kDa MWCO3-10 mL 5 tubes PURG10015 1 kDa MWCO10-15 mL 5 tubes PURG10020 1 kDa MWCO15-20 mL 5 tubes PURG35010 3.5 kDa MWCO3-10 mL10 tubes PURG35015 3.5 kDa MWCO10-15 mL10 tubes PURG35020 3.5 kDa MWCO15-20 mL10 tubes PURG60010 6-8 kDa MWCO3-10 mL10 tubes PURG60015 6-8 kDa MWCO10-15 mL10 tubes PURG60020 6-8 kDa MWCO15-20 mL10 tubes PURG12010 12-14 kDa MWCO3-10 mL10 tubes PURG12015 12-14 kDa MWCO10-15 mL10 tubes PURG12020 12-14 kDa MWCO15-20 mL10 tubesThe capacity range of the tubes in each Mega Pur–A–Lyzer Kit is determined by the caps accompanying the tubes.Figure 1: Caps available with different Mega Pur–A–Lyzer Kits Each kit includes a floating rack along with thePur-A-Lyzer tubes (PURNR-1EA).The regenerated cellulose membrane is ultraclean,sulfur and heavy metal free, and EDTA treated.Pur-A-Lyzers are tested for simple dialysis of salts or buffer exchange. The quality of the sample after dialysis is checked by several assays. Determining the recovery from a specific amount of loaded sample also tests the quality and efficiency of the Pur-A-Lyzer membrane. Precautions and DisclaimerThis product is for R&D use only, not for drug, household, or other uses. Please consult the Material Safety Data Sheet for information regarding hazards and safe handling practices. Granted Patent related to Pur-A-Lyzer, (1). Australia 2001262612, (2). Canada 2410322, (3). Europe 1285257, (4) India 201731, (5) S Korea 823939, (6) USA 7074313. Storage/StabilityStore the Pur-A-Lyzer kit in a dry place at room temperature. Under these conditions, a kit can be stored for up to12 months without any deterioration in performance and quality. For longer storage time, it is recommended the Pur-A-Lyzer kit be stored in a cool place (refrigerator),at a relative humidity of at least 35%.ProceduresDialysis with Mega Pur-A-LyzerSample concentration by evaporationProtein precipitationDNA/RNA concentrationDialysis with Mega Pur–A–LyzerFigure 2: Dialysis with Mega Pur–A–Lyzer. Procedure1. Fill the Pur–A–Lyzer with 20 mL of ultrapure water;incubate for at least 5 minutes. Empty the tube.Note: Check carefully that there is no water leakingfrom the tube. Absorption of water by the drymembrane will cause a decrease in water level.2. Load sample into the Pur–A–Lyzer tube. Close the tubewith the provided caps (do not apply force).Sample volume should be in the range of 3-20 mL.If small volume is used, load the sample close to theinner membrane.3. Place the loaded Pur–A–Lyzer tube in the suppliedfloating rack and then place the rack in a stirred beaker containing a large volume (usually 100 to 1000–fold that of the sample) of the desired buffer.Adjust the stir bar speed. Allow at least 30 minutes foreach 0.1 mL of sample. Low–molecular weight salts andbuffers (e.g., tris and phosphate) equilibrate within 3 hours.Equilibration times for viscous samples will be longer.Note: Adjust floating rack height on Mega Pur-A-Lyzer for upright floating balance during dialysis process.For dialysis of less than 5 mL, place the floating rack atmiddle height of the Mega Pur-A-Lyzer. For dialysis ofmore than 5 mL, adjust the floating rack at the top ofPur-A-Lyzer (see Figure 3)The floating rack can hold 1 Pur–A–Lyzer tube.Figure 3. Positions of the floating rack on Mega Pur–A–Lyzer tubes. (For multiple samples or high-volume work, additional floating racks are available. See Kit Contents section for product number.)3. Adjust the stir bar speed. Allow at least 30 minutes foreach 0.1 mL of sample. Low–molecular weight salts andbuffers (e.g., tris and phosphate) equilibrate within 3 hours.Equilibration times for viscous samples will be longer.Note: The user must determine exact equilibrationtimes for the dialysis.4. Change the dialysis buffer as necessary.5. Pipette the sample carefully from the Pur–A–Lyzer to aclean tube.If sample volume increased during dialysis, concentrate the sample by evaporation.Sample Concentration by Evaporation with Mega Pur–A–LyzerPur–A–Lyzers kits are ideally suited for concentration of the sample by evaporation because of their dual membranes and large surface area. Dialysis and concentration in the same device reduce protein loss. Unlike closed–system centrifuge–type devices, sample concentration can be easily monitored in the Pur–A–Lyzers.1. P lace a sample in the Pur–A–Lyzer or use alreadydialyzed sample, and place it on micro tube rack stand.2. Let the sample evaporate on the bench top (using a fanto increase airflow across the membrane will speed up the process), making sure to check every 10 minutes or less to prevent evaporation to dryness.Note: When evaporating water from the sample, small molecules (buffer salts, reducing agents, etc.) will alsobe concentrated.Trichloroacetic acid (TCA) precipitation procedure 1. Add equal volume of 20% TCA to the tube containingthe protein solution and mix properly.For example, add 10 mL of 20% TCA to a 10 mL sample.2. Incubate 60 minutes in 4 °C.3. Spin the tube at 4 °C for 30 minutes at 14,000 rpm.4. Discard supernatant carefully.5. Add 7 mL of cold acetone.6. Incubate at –20 °C for 60 minutes and centrifuge thesample at 4 °C for 30 minute sat 14,000 rpm.To increase protein precipitation yield incubate thesamples over night at –20 °C.7. Discard supernatant and air–dry the pellet.8. Resuspend the pellet in appropriate buffer (use at least0.7 mL to perform resuspension).DNA or RNA precipitation1. Add 0.1 volume of 3 M potassium acetate, pH 5.2, and0.7–1 volume of isopropanol to the solution. Mix gentlyby inverting the tube several times.For example, add 1 mL of 3 M potassium acetate,pH 5.2, and 7–10 mL isopropanol to a 10 mL sample.Note: Addition of a carrier (e.g. 20 µg of tRNA or 20 µgof glycogen) to the solution will increase the efficiency of precipitation.2. Incubate at –20 °C for 10 minutes.To increase DNA or RNA precipitation yield incubate the samples over night at –20 °C .3. Centrifuge the sample at 4 °C for 30 minutes at14,000 rpm.4. Carefully discard the supernatant without disturbingthe pellet.5. Wash the pellet with a cooled 70% ethanol solution.6. Air–dry the pellet for 5–20 minutes.Do not over–dry the pellet (e.g., by using a vacuumevaporator), as this will make the DNA, especially if it is of high molecular weight, difficult to redissolve.7. Redissolve the DNA or RNA in a suitable buffer.Use a buffer with pH >8.0 for redissolving, as DNA does not dissolve readily in acidic buffers.78113 1032Order/Customer Service (800) 325-3010 • Fax (800) 325-5052 Technical Service (800) 325-5832 • /techserviceDevelopment/Custom Manufacturing Inquiries (800) 244-1173Safety-related Information /safetycenter ©2012 Sigma-Aldrich Co. LLC. All rights reserved. SIGMA and SIGMA-ALDRICH are trademarks of Sigma-Aldrich Co. LLC, registered in the US and other countries. Sigma brand products are sold through Sigma-Aldrich, Inc. Sigma-Aldrich, Inc. warrants that its products conform to the i nformation contained in this and other Sigma-Aldrich publications. Purchaser must determine the suitability of the product(s) for their particular use. Additional terms and conditions may apply. Please see reverse side of the invoice or packing slip. World Headquarters 3050 Spruce St. St. Louis, MO 63103 (314) 771-5765 Enabling Science toImprove the Quality of Life。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Product InformationHighPerformanceGrease Molykote® EM-30L Grease•Can be used for plastic-plastic contact, metal-metal contact andplastic-metal contact•Long service life•Low seepage, so it can be used in places wherein cleanliness isrequired•Does not contain silicone thereby preventing problems with contact point failures COMPOSITION•Poly-±-olefin•Lithium soap•PTFE, etc. Lubricating grease developed for plastic components APPLICATIONS•Automobiles, electrical appliances, precision equipment, audio equipment, and office equipment that have plastic parts.TYPICAL PROPERTIESSpecification Writers: These values are not intended for use in preparing specifications. Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.Test*Property Unit ResultAppearance WhiteBase oil viscosity at 40ºC mm²/s 90JIS K 2220 Penetration (worked 60 times) 325NLGI class 1Service temperature range ˚C-45 to 150Density g/cm30.91JIS K 2220 Drop point ˚C195JIS K 2220 Bleed (100ºC24 hours) % 5.0JIS K 2220 Evaporation (99ºC22 hours) % 0.4JIS K 2220 Oxidation resistance (99ºC100 hours) MPa 0.02JIS K 2220 Copper corrosion (100ºC 24 hours) 1AASTM D 2596 Four ball weld load (1500rpm/1minute) N 3730ASTM D 2266 Four ball wear scar(1200rpm, 392N, 1 hour) mm 0.5JIS K 2220 Low temperature torque test (-40ºC)Starting torque mNm 110Running torque mNm 51*JIS: Japanese Industrial Standard.ASTM: American Society for Testing and Materials.HOW TO USEClean points of application.As is usual with lubricating greases,apply or fill by means of a brush,spatula, or automatic lubricationdevice.HANDLING PRECAUTIONSThis product may irritate the skin oreyes. Wear safety equipment asnecessary when handling this product.In the event of contact with skin oreyes, immediately rinse thoroughlywith water and seek medical care ifnecessary. Wash hands thoroughlyafter handling. At high temperatures inexcess of 250ºC, the breakdown offluorinated polymer can cause therelease of a small amount of toxic gas.Ensure adequate ventilation.Molykote ® EM-30L Grease Dow Corning and Molykote are registered trademarks of Dow Corning Corporation.2011, May 25We help you invent the future is a trademark of Dow Corning Corporation.Form No. 80-3106B-01©2002, 2006, 2011 Dow Corning Corporation. All rights reserved.2USABLE LIFE AND STORAGEWhen stored, unopened in a cool, dark place Molykote ® EM-30L Grease, has a usable life of 36 months from the date of production.PACKAGING INFORMATIONThis product is available in 1kg cans (10 cans/case) and 16kg pails.LIMITATIONSThis product is neither tested nor represented as suitable for medical or pharmaceutical uses.HEALTH ANDENVIRONMENTAL INFORMATIONTo support Customers in theirproduct safety needs, Dow Corning has an extensive ProductStewardship organization and a team of Product Safety andRegulatory Compliance (PS&RC) specialists available in each area. For further information, please see our Web site, or consult your local Dow Corning representative.LIMITED WARRANTY INFORMATION – PLEASE READ CAREFULLYThe information contained herein is offered in good faith and isbelieved to be accurate. However, because conditions and methods of use of our products are beyond our control, this information should not be used in substitution forcustomer’s tests to ensure that our products are safe, effective, and fully satisfactory for the intended end use. Suggestions of use shall not be taken as inducements to infringe any patent.Dow Corning’s sole warranty is that our products will meet the sales specifications in effect at the time of shipment.Your exclusive remedy for breach of such warranty is limited to refund of purchase price orreplacement of any product shown to be other than as warranted. DOW CORNINGSPECIFICALLY DISCLAIMS ANY OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR APARTICULAR PURPOSE OR MERCHANTABILITY. DOW CORNING DISCLAIMS LIABILITY FOR ANY INCIDENTAL ORCONSEQUENTIAL DAMAGES. We help you invent the future. ™ 。