602030中英文规格书
锂电池规格书(中英文)
History of revision版本更改历史记录Contents 目录1．Scope 适用范围 32．Adopted Standard引用标准 33．Electrical Characteristics电气特性 34．Battery Performances Test Criterion 电池性能测试规范 35.1 Appearance 外观 35.2 Measurement Apparatus 测试设备 35.3 Testing Condition 测试条件 35.4 Reliability Test 可靠性测试 35．Shipment 运输 36．Storage 贮存 37．Package and Marking包装与标志 38.1 Package 包装 38.2 Marking 标志 38．Protection Circuit 保护电路 39.1 Schematic of the PCB 保护板原理图 39.2 PCM BOM9.3 PCM Parameter PCM参数 39．Outline Drawing 外形图纸 310．Appendix 附录 33.7 Instructions and Safety Requirement 使用说明和安全规程 33.7.1 Recommending Usage推荐使用事项 33.7.2 Hazard Warning危险警告 33.7.3 Warning 警告 33.7.4 Cautions 注意事项 310.2 Quality Evaluation Programme 质量评定 310.3 Environment Protection 环保要求 310.4 Others 其他事项 31．Scope 适用范围This description defines the general requirements for thebattery’s rating parameter, electrical requirement, safety requirement, environmental compatibility, test and judgment, usage instructions, safety regulation, quality evaluation and packaging, marking, storage,shipment and handling, which cellular phone battery with 523450AR-850mAh rechargeable battery cell, adapted for Digital products.本规格书描述电池之标称参数、电气特性、安全性能、环境适应性及其实验和判定、使用说明和安全规程、质量评定及包装、标志、贮存、运输等。
DPG60C300HB;中文规格书,Datasheet资料
HiPerFRED²Features / Advantages:Applications:Package:Part numberV I RRM ==30030DPG 60 C 300 HBV A 2x Backside: cathodet rr =35nsHigh Performance Fast Recovery Diode Low Loss and Soft Recovery Common Cathode● Planar passivated chips● Very low leakage current ● Very short recovery time ● Improved thermal behaviour ● Very low Irm-values● Very soft recovery behaviour● Avalanche voltage rated for reliable operation ● Soft reverse recovery for low EMI/RFI ● Low Irm reduces:- Power dissipation within the diode- Turn-on loss in the commutating switch● Antiparallel diode for high frequency switching devices ● Antisaturation diode ● Snubber diode● Free wheeling diode● Rectifiers in switch mode power supplies (SMPS)● Uninterruptible power supplies (UPS)FAVI RMS A per pin 50R thCH K/W 0.25M D Nm 1.2mounting torque 0.8T stg °C 150storage temperature-55Weight g 6Symbol DefinitionRatingstyp.max.min.Conditions RMS currentthermal resistance case to heatsink Unit I is typically limited by: 1. pin-to-chip resistance; or by 2. current capability of the chip.In case of 1, a common cathode/anode configuration and a non-isolated backside, the whole current capability can be used by connecting the backside.F CN120mounting force with clip20Ordering Delivering ModeBase Qty Code KeyStandard Part Name DPG 60 C 300 HB 502163Tube 30D P G 60C 300 HBPart numberDiodeHiPerFRED extreme fastCommon CathodeT O-247AD (3) ===DPG60C300QB DPG60C300HJ DPG60C300PC DPF60C300HB TO-3P (3)ISOPLUS247 (3)TO-263AB (D2Pak) TO-247AD (3)Similar PartPackage1)1)Marking on Product DPG60C300HB 300300300300Voltage ClassCurrent Rating [A]Reverse Voltage [V]====RMSDPG80C300HB TO-247AD (3)300分销商库存信息: IXYSDPG60C300HB。
锂离子聚合物电池规格书说明书
页码：1/15602030PL300mAhSpecification of Li-ion Rechargeable Battery锂离子电池规格书Model：602030PL300mAh/3.7VCustomer Confirmation Customer Name: Customer No.: Comment:Customer Approval:Prepared by Checked by Approved by 肖志军602030PL300mAh页码：2/15兴永恒（深圳）电子有限公司深圳宝安区沙井后亭E-mail：****************Website：TEL：86-0755-********FAX：86-0755-********AMENDMENT RECORDSREVISION DATE ORIGINATOR REASON FOR REVISION A001 2016-6-20602030PL300mAh页码：3/15Content目录1. Scope范围 (4)2. Reference Standard 参考标准 (4)3. Picture of battery电池图 (4)3.1 Picture of single cell 单体电芯图 (4)3.2 Picture of assembled battery 组合电池图 (6)4. Basic of performance 基本性能 (7)4.1 Single cell parameters 单体电芯参数 (7)4.2 Assembled cell parameters包装后电芯组参数 (8)5. Electrical Characteristics电性能 (8)5.1 Normal Test Conditions标准测试条件 (8)5.2 Electrochemical Characteristics电化学性能 (8)5.3 Environment Characteristics环境适应性能 (9)5.4 Safety Characteristics 安全性能 (10)6. PCM Specification PCM 规格 (11)6.1 Electrical Characteristics电性能 (11)6.2 Circuit Diagram 电路图 (11)6.3 Circuit topology Drawing and PIN Explanation电路布线图和焊盘说明 (12)6.4 PCM BOM 保护板物料清单 (12)7. Storage and Shipment Requirement存储及运输要求 (13)8. Warning and Cautions 警告及注意事项 (13)9. Note 声明 (15)页码：4/15602030PL300mAh1. Scope范围This specification describes the performance, testing method, warning and caution of the lithium-ion rechargeable battery.The specification applies to polymer battery supplied by Shenzhen biyate energy co., ltd本标准描述了锂离子电池的性能、测试方法及注意事项。
r6020场效应规格书
r6020场效应规格书英文回答：The R6020 is a type of field-effect transistor (FET) that is commonly used in electronic devices and circuits.It has specific specifications that determine its performance and capabilities. Let's take a closer look at the specifications of the R6020 FET.One of the important specifications of the R6020 FET is its drain-source voltage (VDS) rating. This specification indicates the maximum voltage that can be applied across the drain and source terminals of the transistor without causing damage. For example, if the VDS rating is 30V, it means that the transistor can safely handle voltages up to 30V in this configuration.Another crucial specification is the drain current (ID) rating. This specification refers to the maximum current that can flow through the drain terminal of the transistorwithout exceeding its limits. It is important to ensurethat the ID rating is not exceeded to prevent overheating and potential damage to the transistor.The R6020 FET also has a threshold voltage (VGS(th)) specification. This voltage determines the point at which the transistor starts to conduct current between the drain and source terminals. It is important to consider this threshold voltage when designing circuits that utilize the R6020 FET to ensure proper operation.Additionally, the R6020 FET has a gate-source voltage (VGS) rating. This specification indicates the maximum voltage that can be applied between the gate and source terminals without causing damage. It is essential to stay within this voltage rating to prevent any potential harm to the transistor.Furthermore, the R6020 FET has an on-state resistance (RDS(on)) specification. This resistance value represents the resistance between the drain and source terminals when the transistor is fully conducting. A lower RDS(on) valueindicates better conductivity and efficiency of the transistor.Lastly, the R6020 FET has a power dissipation (PD) rating. This specification refers to the maximum amount of power that the transistor can safely dissipate without exceeding its temperature limits. It is crucial to consider the PD rating to prevent overheating and potential failure of the transistor.In conclusion, the R6020 FET has several important specifications that determine its performance and capabilities. These specifications include the drain-source voltage rating, drain current rating, threshold voltage, gate-source voltage rating, on-state resistance, and power dissipation rating. By considering these specifications, engineers can design circuits and electronic devices that utilize the R6020 FET effectively and reliably.中文回答：R6020场效应管是一种常用于电子设备和电路中的场效应晶体管。
moc3020规格书
moc3020规格书
以下是MOC3020规格书的内容：
1. MOC3020是一种高隔离压力的光耦合器，用于隔离输入和输出电路。
2. 输入部分包括一个红外LED和一个光电二极管。
输出部分包括一个三端可控硅。
3. MOC3020的最大隔离电压为7500Vrms，最大工作电流为60mA。
4. 输入端的最大正向电流为60mA，最大反向电压为6V。
5. 输出端的最大正向电流为0.1A，最大反向电压为400V。
6. MOC3020的触发电流为5mA，触发电压为1.5V。
7. MOC3020的工作温度范围为-40°C至+100°C。
8. MOC3020采用DIP-6封装，适用于插装式电路板。
以上是MOC3020规格书的一些基本内容，详细的规格和参数请参考相关文档或官方资料。
电池规格书模板
Specification Approval Sheet 产品规格承认书Customer 客户名称：域拓Model产品型号：4LType 产品类型：Li-ion battery Specification产品规格：3.7V/1400mAHAMENDMENT RECORDSCatalogue 目录1 .Battery type and scope电池型号和适用范围 (3)1 . 1: model产品型号： (4)1 . 2: scope适用范围：客户定义 (4)2 . Basic character and compose of battery电池的基本特性及组成 (4)2 . 1: fundamental performance parameter of battery电池基本性能参数： (4)2 . 2: Main components and parts主要零部件 (6)2 . 3: Regular performance and unfailing performance产品常规性能和可靠性能 (6)2 . 4: Contour Dimension of the Battery电池外形尺寸 (11)3 . Specifications of Parts零部件规格 (102)3 . 1: fender保护板 (102)3 . 2: general electric and protection characters一般电气与保护特征 (102)3 . 2: electric schematic diagram of battery电池电路原理图： (113)3 . 3 : PCB layout 电路布局图………………………………………………………………….错误!未定义书签。
34 . Specifications of the Cells电芯规格 (124)Announcements注意事项 (135)Danger 危险 (135)Warnings 警告 (146)Announcements 注意事项 (157)1 .Battery type and scope电池型号和适用范围This Specification Approval Sheet is for rechargeable Li-polymer battery provided by Shirui Battery Co., LTD.This product is according with the national standard of PRC. ‘GB/T18287-2000’. ‘General specification of lithium-ion battery for cellular phone’.本《规格书》为时瑞电池有限公司提供的可充电式锂离子电池规格。
0190030077;中文规格书,Datasheet资料
This document was generated on 08/13/2012PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:19003-0077Status:ActiveDescription:InsulKrimp™ Quick Disconnect, Female, for 14-16 (2.00-1.30mm²), Mylar Tape, Tab 5.21 x 0.51mmDocuments:Drawing (PDF)Product Specification PS-19902-015 (PDF)Product Specification PS-19902-008 (PDF)RoHS Certificate of Compliance (PDF)Product Specification PS-19902-011 (PDF)Agency CertificationULE79133GeneralProduct Family Quick Disconnects Series19003CommentsFunnel Entry Crimp Quality Equipment YesProduct Name InsulKrimp™Type Quick Disconnect UPC800753029675PhysicalBarrel Type Closed Color - Resin Natural Flammability 94V-2GenderFemale Glow-Wire Compliant NoInsulationNylon (PA)Lock to Mating Part None Material - MetalBrass Material - Plating MatingTin Material - Plating Termination Tin Material - Resin Nylon Net Weight 0.730/g OrientationStraightPackaging Type Adhesive Tape on Reel Plating min - Mating4.064µm Plating min - Termination 4.064µm Polarized to Mating Part NoTab Thickness 0.51mm Tab Width5.21mmTemperature Range - Operating -65°C to +105°CTermination Interface: Style Crimp or Compression Wire Insulation Diameter 4.06mm max.Wire Size AWG 14, 16Wire Size mm²1.30 -2.00ElectricalVoltage - Maximum600V Material InfoOld Part NumberBB-2215TReference - Drawing NumbersProduct Specification PS-19902-008, PS-19902-011, PS-19902-015Sales DrawingSD-19003-005Seriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHC Not ReviewedLow-Halogen Status Not ReviewedNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 19003SeriesApplication Tooling | FAQTooling specifications and manuals are found by selecting the products below.Crimp Height Specifications are then contained in the Application Tooling Specification document.GlobalDescription Product #Crimp Dies for the ATP-301 Air Crimping Press for Mylar TapeMounted Terminals and MTA-106 Tape Applicator used in Wire Processing Machine 0192880105Mini-Mac™Applicator0638854200This document was generated on 08/13/2012PLEASE CHECK FOR LATEST PART INFORMATION分销商库存信息: MOLEX 0190030077。
0191540038;中文规格书,Datasheet资料
This document was generated on 08/06/2012PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:19154-0038Status:ActiveOverview:SpliceDescription:BUTT SPLICE INSULKRIMP TAPED (CS-V-346XTDocuments:Drawing (PDF)Product Specification PS-19902-015 (PDF)Product Specification PS-19902-007 (PDF)RoHS Certificate of Compliance (PDF)Product Specification PS-19902-011 (PDF)Agency CertificationCSA LR18689ULE32244GeneralProduct Family Splices Series19154Crimp Quality Equipment Yes Mil-Spec N/A OverviewSpliceProduct Name Butt, InsulKrimp™UPC800753109032PhysicalBarrel Type Closed Color - Resin Natural Flammability 94V-0InsulationPVC Material - Resin PVC Net Weight3.241/gPackaging Type Adhesive Tape on Reel Wire Size AWG10, 12Material InfoOld Part NumberCS-V-346XTReference - Drawing NumbersProduct Specification PS-19902-007, PS-19902-011, PS-19902-015Sales Drawing6000208CSeriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHC Not ReviewedLow-Halogen Status Not ReviewedNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 19154SeriesApplication Tooling | FAQTooling specifications and manuals are found by selecting the products below.Crimp Height Specifications are then contained in the Application Tooling Specification document.GlobalDescription Product #Crimp Dies for MTA-100 Tape Applicator used in 3BF Press, MTA-105Tape Applicator used in TM-2000™ Press,and ATP-301 Air Crimping Press for Mylar Tape Mounted Terminals0192880200This document was generated on 08/06/2012PLEASE CHECK FOR LATEST PART INFORMATION分销商库存信息: MOLEX 0191540038。
电子产品中英文规格书完整版
Page 1 Of 12 ShenZhen C&D Electronics CO.Ltd.Add: Building 2, Xiayousong Mountaintop Industrial District,Yousong Village,LongHua Town, Baoan District ShenZhen China Zip 518109Tel: 86-755- 28142422 Fax: 86-755-28142699 E-mail:****************** Remote control specification(Rev. A0)Seller CustomerPart Name :Remote control Part No. : Part Name : Part No. :Seller approval Customer approvalPrepared By: Date:Received by: Date：Checked By: Date: Checked by: Date:Approved By: Date:Approved by: Date:company chop：company chop：Change historyVersion Date Description AuthorPage 2 Of 12 2、目录Index3.检验内容及要求(Verification content & Requirement) Page 3Of 121、一般项目(General Items)1.1、适用范围Apply for: RC35J remote1.2、工作环境Working Environment: -10℃~40℃、45﹪~90﹪RH、86~106Kpa1.3、存储温度Storage Temperature :-40℃~70℃1.4、试验环境Test Environment: 5℃~35℃、45﹪~75﹪RH、86~106Kpa1.5、额定电压Rating Voltage:DC3.0V1.6、适用电池Power: AAA*2 pcs1.7、重量范围：25g +/-5g（Extra weight is 25g +/-5g）2、可视检测项目Visible Test Item测试条件Test ConditionsA:正面在标准光源下30CM距离10秒以内目测Put the top face under the standard light source and test by sight from the 30cm distance for 10 secondsB:其余面标准光源下50CM距离5秒以内目测Put other sides under the standard light source and test by sight from the 50cm distance for 5 seconds序号No.项目Item测试要求Test Requirements2.1划伤、沾污、割裂、变形Scratches, Stain and distortion of the Unit符合摩托罗拉规格书365-095-08990According to Moto specification, 365-095-089902.2印刷图形及文字Hot Stamped Graphics and Letters 内容正确、清晰、均匀、整齐Correct, in focus and comply With the drawing2.3壳体配合Match of top case and bottom case 无翘起、变形、开裂、断差No distortion and Crack between the two parts2.4表面Appearance材质正确、顔色一致Correct material and color3、电气性能Electric Capability序号项目测试要求Test Requirements3.1载波频率Carrier frequency36KHZ ±1K3.2工作电压Working Voltage DC2.2V~3.6V3.3待机电流Static Current≤5uA3.4工作电流Working Current≤50mA3.5发射角度和距离Transmit Angel and Distance （工作电压3.0V)Working Voltage(3V)3.6码表Code Table见码表图Refer to the Code Table 3.7工作原理图Schematic Diagram见工作原理图Schematic DiagramPage 6Of 12Page 7Of 12 4、码表(Code tableve )Page 8Of 12 5、产品效果图(Product Cosmetics drawing)6. 原理图(Schematic diagram) Page 9Of 12Page10Of 12 7、爆炸图(Explosion drawing)Page 11Of 12 8、产品尺寸图(Dimension drawing)9、包装尺寸图(Packaging drawing) Page 12 Of 12 Label inside Battery door:Label for PE plastic package: Lable for carton box:Packing drawing：。
F960中英文规格书
Product pictures:产品图片批准/日期深圳市永興輝實業發展有限公司Shenzhen YXH Industry Development Co.，Ltd编号:YXH-SPE-CE-3008版本:00/00日期:2009-7-03F960产品规格书地址:广东省深圳市龙岗区中心城五联社区连心路五联工业区桑格电子电话:0755-********Customer Approval:客户承认SpecificationProduct model：F960产品型号：F960Customer Model：客户型号：传真:0755-********编制/日期审核/日期F960锂离子电池规格说明书F960 Li-ion Battery specification1.范围 Range1.1 这份说明书适用于可充电的F960锂离子电池. This specification apply to rechargeable li-ion battery F9601.2 这份说明书仅适用于F960的电池 This specification only fit for F960 Battery2.种类型号 Type&model2.1 种类 Type锂离子可充电电池 Li-ion Rechargeable battery2.2 型号 modelSG-DVBT008-F960为公司型号 SG-DVBT008-F960 Company model3.规格 specification3.1 电芯18650规格 Battery Cell 18650 Specification数值C riteria 单位Units 单位U nits 数值C riteria单位Units单位U nits4.325-4.375伏（V）微安（uA）4.10-4.20伏（V）毫欧（m Ω）2.2-2.4伏（V）安（A）0.3-0.5毫秒（mS）KW76AABU1U211-153.2.7过流保护电流Over-currentprotection current数值C riteria 电性能参数 electrical property parameter项目Item 50-653.2.6内阻Conduction resistance 3.2.5自耗电流 self-consuming current项目I tem项目Item数值C riteria29-403.2.2过充恢复电压Over-chargeresuming voltage 3.2.3过放保护电压Over-discharge protection Voltage 3.2.8识别电阻（T） 识别电阻（D）锂电保护IC开关MOS管8205(SOP8)Picture and dimension3.3 F960 外壳规格 F960 Specification of shell3.1.14 外表标示 apperance marking ICR 18650目视 visual3.2.4短路保护延时间Short circuit protection delay外型尺寸3.2 F960 PCB板的规格 F960 PCB SpecificationMain chip application3.2.1过充保护电压Over-chargeProtection Voltage ItemTesting condition项目I tem 备注:1C=2100mAhThickness:1.9mm正负公差:0.1mm标 准 standard测试条件 Test condition3.4.1 标称电压 nominal voltage 6450mAh3.3.1 面3.4 F960成品规格 F960 finished-product Specification高精度数显卡尺high-precision callipers3.3.3 组合高精度数显卡尺high-precision callipers内阻仪 BVIR ≥6300mAh 典型6450mAhtypical 6450mAh高精度数显卡尺high-precision callipers 3.3.2 底5.5V 7.8V±0.1V ﹤86m Ω规 格 Specification 项目 item8.5V 3.4.7 出厂内阻 routine internal resistance 3.4.8 重量 weight3.4.9 外尺寸 outside dimension293g70.4*38.5*59.7mm分容老化柜 grading andaging cabinet 高精度万用表high precision digitalmultimeter天秤 Libra 3.4.6 出厂电压 routine voltage 7.2V3.4.2 标称容量 nominal capacity 高精度数显卡尺high-precision callipers3.4.3 实际容量 practical capacity 3.4.4 充电终止电压 final charging voltage3.4.5 放电终止电压final discharging voltage正负公差:0.1mm正负公差:0.1mm长宽公差:±0.1mm 厚度公差:±0.05mm4. 电池船运条件及保质期限 The shipping conditions and warranty4.1 船运条件:大约20-30%容量.4.2 保质期限:从电池生产完成日开始的12个月内.5. 电池使用时警告及注意事项：WARNINGS AND CAUTIONS IN HANDING THE LITHIUM-IONBATTERY警告warningA、危险警告： Danger warningDanger warning should be described in manual or instruction for users为防止电池可能发生泄漏，发热，爆炸，请注意以下预防措施：To prevent the possibility of the battery from leaking,heating, explosion please observe the following precautions:with metal objects such wirehairpins etcB、注意以下项目* 不要加热和扔进火中.Do not heat or expose charger to fire.* 禁止拆开电池及改变电池内部结构Do not open the battery and change the internal structure* 不要装配或遗留在高温(超过60℃)设备中.Do not assemble or leave it in the hightemperature equipment (≥60℃）* 不要用金属直接短接电池正极和负极终端.Do not use metal directly contacting battery positive and negative poles* 不要湿水,受潮.Keep away from water ; Dampproof充电注意chargering attention* 充电温度限制在 0℃至 +45℃.chargering temperature limited between 0℃ and +45℃.* 不要反充和未充电就进行过放电.Do not over discharge before* 最好的充电是按电池专门设计方式进行.The best charging way is according the battery special designed way* 充电时用制造厂指定的设备并遵循正确使用方法;When charging,using the appointed machine of factory and following thecorrect using way.放电注意Dischargering Attention* 放电温度限制在-20℃至 +60℃.discharging temperature limited between 20℃ and +60℃* 避免放电至2.5V以下, 不要过放电至1.0V以下.Avoid discharging below 2.5V,do not over discharger below1.0 V* 以规格书指定的电流放电并遵循环境温度.Following as specification appointed current dischargeand environmental temperature贮存注意Storage Attention* 贮存一个较长时期后要完全充放不少于三个循环.After storing for a long time,need fully charge anddischarge not less than three cycles.* 贮存在干燥和室温条件.Store at the dry and indoor condition* 贮存时电池带电量不多于30%.The battery with quantity ofelectricity less than 30% when storing.C、小心Carefulness引起电池过热，起火或功能失效，寿命减短。
20263;中文规格书,Datasheet资料
BDCCA 4.52.461.800 3.600R.0212 PLCS.2056PLCS2.122.00±.02.066 PLCSFULL RAD 6 PLCSR.134 PLCSAASEE NOTE 4.188.188.007SEE DETAILSECTION A-ANOTES:1. MATERIAL: MAKE FROM HENKEL AL-2-45H-212.2. THICKNESS: .007±.001.3. SEE DETAIL FOR ASSY ORDER.4. FOR ARTWORK SHOWN HERE SEE DWG# 20200.5. DENOTE CRITICAL CHARACTERISTIC FOR LOT INSPECTION.6. RoHS COMPLIANT PER CST-0001 LATEST REVISION.7. PRIOR TO ASSEMBLY, PRODUCTS SHALL BE STORED IN A COOL, DRY LOCATION IN ORIGINAL PACKAGING AT TEMPERATURES BELOW 40°C (104°F). UNDER THESE CONDITIONS THE SHELF LIFE IS INDEFINITE. THERMMATE PADS CAN BE PRE-APPLIED TO BASEPLATES OR HEAT SINKS WHICH ARE THEN SHIPPED TO A FINAL ASSEMBLY LOCATION, AS LONG AS THE TEMPERATURE DOES NOT EXCEED THE LEVEL INDICATED ABOVE.FEDETAIL :A. SPLIT RELEASE LINER.B. ADHESIVE STRIP; .0025 THICK .188 WIDE.C. ALUMINUM ALLOY 1145-0; .002 THICK.D. ROLL CARRIER WITH ADHESIVE STRIP BONDING.E. PHASE CHANGE THERMAL COMPOUND.F. ADHESIVE STRIPS ON ROLL CARRIER.(VERTICAL THICKNESS IS NOT SHOWN TO SCALE).188.007PEI AABBCCDDEEFF1122334455667788SWDTHERMAL INTERFACE PADTHERMATE (MAXI)P/N 202632/13/97J. RENAUDDATE DRAWN REV5DWG NO16188CAGE CODE67131SIZEBSHEET 1 OF 1SCALE 1: 1RELEASED PER E0430434VICORUNLESS OTHERWISE SPECIFIED DIMENSIONS ARE INCH [MM]TOLERANCES ARE:DECIMALS ANGLES X.XX [X.X] = ±0.01 [0.25] ±1°X.XXX [X.XX] = ±0.005 [0.127]FN 2REVISED PER E101310b KUK 09/16/04REVISED PER E090673C REVISED PER E091595a AR JS 3404/22/0909/10/09REJH REJH DO NOT SCALE DRAWINGTHIRD ANGLE PROJECTIONVICOR CONFIDENTIALTHIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED ORDISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP.DATE 1DESCRIPTIONFINISHREVISIONSREV MATERIALAPPROVED10/22/10AR 11/07/11KUKREVISED PER E1110905REJH/分销商库存信息: VICOR20263。
LL-060-12-00-00-00;中文规格书,Datasheet资料
General tolerances:
First angleric: [mm]
Heat sinks and, if applicable, D-plates and shrouds in anodised aluminium. Pavel Cech Henrik Höjer H Lindberg 050607
1
2
3
6
\\Server1\konstruktion\Aggregat\LL\LL-060-12-00-00-00.dft 7
LL-060-12-00-00-00
2 Serie 1:1 8
A3, 1(4)
This drawing is the property of Supercool AB. Protected in accordance with prevailing law.
F
Pavel Cech Henrik Höjer H Lindberg 050607
Supercool AB
Box 27, S-40120 Göteborg, Sweden tfn: +46 31 420530, fax: +46 31 247909 e-mail: info@supercool.se Web:
0 0 0 0
66 W at dT=0°C . Toler anc e: ±10%. 12 VDC . Nominal: 12 VDC, Max: 15 VDC. Nominal: 3 9 . A at dT=0°C. Toleran ce: ±10%. None None None 0.5 3 kg 75°C ±5°C on hot side heat si nk surface. Not wired in seris with TEM:s. Use it to con trol a relay. 63°C at nominal voltage. Max. s urface tem perat ure: 80°C. Turbulators fitt ed in h eat sink liquide channels. Individual cardboar d box.
0190380006;中文规格书,Datasheet资料
This document was generated on 08/13/2012PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:19038-0006Status:ActiveDescription:InsulKrimp™ Snap Plug Receptacle for 18-22 AWG Wire, Nylon, Fits Male Plug Diameter 4.57mmDocuments:Drawing (PDF)Product Specification PS-19902-013 (PDF)Product Specification PS-19902-011 (PDF)RoHS Certificate of Compliance (PDF)Agency CertificationCSA LR18689ULE152602GeneralProduct Family Quick Disconnects Series19038CommentsFits Male Plug Dia. 4.57mm Crimp Quality Equipment YesProduct Name InsulKrimp™Type Snap Receptacle UPC800753048706PhysicalBarrel Type Closed Color - Resin Natural Flammability 94V-2GenderFemale Glow-Wire Compliant NoInsulationNylon (PA)Lock to Mating Part None Material - MetalBrass Material - Plating MatingTin Material - Plating Termination Tin Material - Resin Nylon Net Weight 1.119/g OrientationStraight Packaging Type BagPlating min - Mating2.540µm Plating min - Termination 2.540µm Tab Thickness N/A Tab WidthN/ATermination Interface: Style Crimp or Compression Wire Insulation Diameter 3.25mm max.Wire Size AWG 18, 20, 22Wire Size mm²0.25 - 1.50ElectricalVoltage - Maximum600V Material InfoOld Part NumberBRA-2180NReference - Drawing NumbersProduct Specification PS-19902-011, PS-19902-013Sales DrawingSD-19038-001Seriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHCContains SVHC: No Low-Halogen Status Low-HalogenNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 19038SeriesApplication Tooling | FAQTooling specifications and manuals are found by selecting the products below.Crimp Height Specifications are then contained in the Application Tooling Specification document.GlobalDescription Product #Hand Crimp Tool 0640012300Crimp Head for the AT-200™ Pneumatic Hand Tool0640052300This document was generated on 08/13/2012PLEASE CHECK FOR LATEST PART INFORMATION分销商库存信息: MOLEX 0190380006。
760301105;中文规格书,Datasheet资料
1.1 1.02012-06-282012-04-01SStSStSStWWWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]H1: Classification Reflow Profile for SMT components:H2: Classification Reflow ProfilesProfile FeaturePreheat- Temperature Min (T smin ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Ramp-up rate (T L to T P )Liquidous temperature (T L )Time (t L ) maintained above T L Peak package body temperature (T p )Time within 5°C of actual peak temperature (t p )Ramp-down rate (T P to T L )Time 25°C to peak temperature Pb-Free Assembly 150°C 200°C60-180 seconds 3°C/ second max.217°C60-150 seconds See Table H320-30 seconds 6°C/ second max.8 minutes max.refer to IPC/JEDEC J-STD-020DH3: Package Classification Reflow TemperaturePB-Free Assembly PB-Free Assembly PB-Free Assembly Package Thickness< 1.6 mm 1.6 - 2.5 mm ≥ 2.5 mmVolume mm³<350260°C 260°C 250°CVolume mm³350 - 2000260°C 250°C 245°CVolume mm³>2000260°C 245°C 245°Crefer to IPC/JEDEC J-STD-020DH Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-GDTof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Washing varnish agent that is used during the production to clean the application might damage or change the characteristics of the wire in-sulation, the marking or the plating. The washing varnish agent could have a negative effect on the long turn function of the product.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The solder profile has to be complied with according to the technical reflow soldering specification, otherwise no warranty will be sustai-ned.•Wave soldering is not applicable. Reflow soldering is recommended.•All products are supposed to be used before the end of the period of 12 months based on the product date-code, if not a 100% solderabi-lity can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 760301105。
PMEG6020ER,115;中文规格书,Datasheet资料
Symbol
Parameter
Conditions
Min
Tj
junction temperature
-
Tamb
ambient temperature
−55
Tstg
storage temperature
−65
Max Unit
150
°C
+150 °C
+150 °C
[1] Device mounted on a ceramic PCB, Al2O3, standard footprint. [2] Tj = 25 °C prior to surge. [3] Reflow soldering is the only recommended soldering method. [4] Device mounted on an FR4 PCB, single-sided copper, tin-plated and standard footprint. [5] Device mounted on an FR4 PCB, single-sided copper, tin-plated, mounting pad for cathode 1 cm2.
PMEG6020ER
2 A low VF MEGA Schottky barrier rectifier
102
Zth(j-a) (K/W)
10
duty cycle =
1 0.75 0.5
0.33 0.25
0.2
0.1 0.05
0.02 0.01 1
0
006aab651
10−1
10−3
10−2
10−1
[1]
锂离子电池产品规格书 MLP502030 250mAh 3.7V说明书
History of specification规格书修订记录Date Contents Remarks 2018-05-12First issue A0Content/目录1.Scope/适用范围Page42.Cell Specification/电芯规格说明Page4/53.Battery/Cell performance test Criteria/电池性能标准Page6 3.1Appearance inspection by visual/外观目测Page6 3.2Environmental test condition/外界环境条件Page6 3.3Electrical characteristics/电气特性Page6 3.4Mechanical characteristics/机械特性Page73.5Safety performance/安全性能Page7/84.Cell initial Dimensions/电芯初始尺寸Page84.2Picture of assembled battery组合电池图5.Protection Circuit保护电路5.1PCM parameter PCM参数6.Circuit topology Drawing and PIN Explanation电路布线图和焊盘说明6.1PCM BOM保护板物料清单6.2Assembled cell parameters包装后电芯组参数附录Page9 Page9 Page9 Page10 Page10 Page101.Scope/适用范围The specification shall be applied to Li-ion Polymer rechargeable battery pack of MLP502030 250mAh3.7V,which is manufactured.本规格书适用于公司生产的MLP502030250mAh3.7V可充电聚合物锂离子电池.2.Cell Specification/电芯产品规格No.Item项目Specification性能1Rated Capacity额定容量250mAh,0.2C discharging2Minimum Capacity最小容量250mAh,0.2C discharging3Normal Voltage标称电压3.70V4O.C.V出厂电压 3.80-4.2V5Charge Ending Voltage充电截止电压4.20±0.03V6Discharge Ending Voltage放电截止电压3.0V7Standard charging method标准充电方式0.5C constant current charge to 4.2V,then constantvoltage4.2V charge till charged current declines to≤0.01C,0℃～45℃8Charge current充电电流Standard charge:0.2CRapid charge:1.0C9charging Time充电时间Standard charge:5.5～6.5hRapid charge:1.5～2.5h10Max.Charging Current最大充电电流1.0C(5℃～+45℃)11Standard dischargingCurrent标准放电电流0.2C constant current discharge to3.0V.10℃～+60℃12Max.Discharging Current最大放电电流1.0C(10℃～+60℃)13Operating environment工作环境Charging:0℃-45℃,65%±25%RHDischarging:10℃-60℃,65%±25%RH14Cell Impedance单电芯内阻＜140mohm，(4.2V AC1KHz measured)15Dimension of Single Cell单电芯尺寸Thickness Max5.0mmWidth Max20.5mmHeight Max30.5mm3.Picture of single cell 单体电芯图Fig.(1)The Dimension of Single Cell图(1)单体电池尺寸图厚度T 宽度W 长度L L1W1E 5.0±0.120.0±0.530.0±0.56.5±1.52.0-3.07.0±1.5UNIT 单位：MM4.Picture of assembled battery组合电池图Fig.(2)The Dimension of Assembled Battery图(2)组合电池外形尺寸图厚度T 宽度W 长度L 线径Ø线型插头型号5.0±0.120.0±1.033.0±1.00.9UL1007/24#XH2.54-2P备注：UNIT 单位：MM5.产品规格及电气参数Product Specification and Electrical Parameters序号Item项目Specification性能1Assembled Mode组合方式1P2Normal Capacity标称容量≥250mAh,0.2C discharging3Normal Voltage标称电压3.7V4Impedance成品内阻＜240mohm，(100%charge AC1KHz measured)5Assembly Dimension装配尺寸Thickness Max5.1mmWidth Max21.0mmHeight Max33.0mm4.Battery/Cell performance test Criteria/电池性能标准4.1Appearance inspection by visual/外观目测There shall be no such defect as rust,leakage,which may adversely affect commercial value of battery.电池外观应没有锈渍、污渍、漏液等影响商业价值的缺陷存在。
602030锂电池参数
602030锂电池参数602030锂电池是一种常见的锂聚合物电池，它的参数包括电池容量、电压、尺寸和重量等。
下面将对602030锂电池的各项参数进行详细介绍。
1. 电池容量：602030锂电池的容量是指电池可以存储的电能大小，通常以毫安时（mAh）为单位。
602030锂电池的容量一般在100mAh到300mAh之间，不同厂家和型号的电池容量会有所不同。
电池容量越大，代表电池存储的电能越多，使用时间也会更长。
2. 电压：602030锂电池的标准电压为3.7伏特（V），但在实际使用中，电池的电压会有一定的变化范围。
通常情况下，电池的工作电压范围为3.0V到4.2V。
电池的电压决定了电池可以提供的电流大小，也是电子设备正常工作所需的电压。
3. 尺寸：602030锂电池的尺寸是指电池的长、宽、厚度。
602030锂电池的尺寸为60mm×20mm×3.0mm，其中60mm表示电池的长度，20mm表示电池的宽度，3.0mm表示电池的厚度。
尺寸紧凑的锂电池适用于体积较小的电子设备，如智能手表、蓝牙耳机等。
4. 重量：602030锂电池的重量通常在约2克左右。
虽然602030锂电池的容量较小，但由于其采用了轻量化设计，可以有效降低电池的重量，适用于对重量要求较高的电子设备。
602030锂电池作为一种常用的电池类型，具有一定的优势和适用范围。
首先，由于其尺寸小巧，适合应用于体积较小的电子设备中。
其次，602030锂电池的容量和电压能满足智能手表、蓝牙耳机、智能家居设备等的电力需求。
此外，602030锂电池具有较高的充放电效率和较低的自放电率，可以提供稳定可靠的电力供应。
需要注意的是，使用602030锂电池时应遵守相关的安全使用规范。
避免电池过充、过放、短路等情况，以免引发安全事故。
同时，选择正规品牌和厂家的电池，并避免使用过期或损坏的电池，以确保使用的安全性和可靠性。
602030锂电池作为一种常见的锂聚合物电池，具有适中的容量、标准的电压、小巧的尺寸和轻量的特点。
2014年9月产品规格书 LR03 中英文对照
60 ±2°C 相对湿度低于 90% RH
60 ±2°C Low 90% RH
测试时长
Test Duration
连续放电 48 小 时
Discharge 48h
30 天
30days
结果
Result
电池的形变不能超
过尺寸规格值的上
限及不能发生肉眼
2) 放电平均结果大于或等于最小平均放电时间，且个体放电时间低于最小平均值的 80%的电
池个数不大于 1，则批次电池容量测试为合格。 The result of the Minimum Average Duration from each discharging standard shall be equal to or more than the Minimum Average Duration requirement; and no more than
0.00% Mercury & Cadmium
：1.5V
4. 平均重量 Average weight
: 11.3g
5. 标称容量 Nominal Capacity
1200mAh (条件: 75Ω 负载, 每天放电 4 小时，终止电压 0.9V ，放电环境：20+/-2°C ) 1200mAh (condition: 75Ω load resistance, discharge 4 hours per day at 20+/-2°C, end-point voltage 0.9V )
Other：AAA，E92，4003
JIS：AM-4
ANSI: 24A
1.2 参考标准 Reference standard