模具术语中英文

合集下载

模具常用术语中英文对照

模芯Parting Core 耐落胶Teflon Paste 局部视图Partial View 偏移量Offset冷料Cold Slag 水塞Water Line Plug 线切割Wire 撬模脚Ppy Slot轮廓Contour 重新加工Reworked 螺纹孔Tapping Hole 配件Components 连接件Fittings 补偿Compensation 斜针Angle Pin 平面度Parallel接合Engage 倒角Chamfer替换镶件Interchangeable Mold Inserts 模胚Mold Base指定吨位的注塑机Specific Press 热嘴Hotnozzle水嘴接头Water Fitting 火花机Edm螺纹Eyebolt Thread 熔接线Weildline回针Stop Pin 压机Press二级顶出针Sub-Leaderd Pin 嗮纹Texturing镶件Mold Insert 梯形Trapezoid加硬Harden 凸缘、法兰Flange 唧嘴Sprue 方铁Spacer Block 设计筒图Design Preliminary 顶针板Ejector Plate 名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Slide Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft 顶针底板Ejector Retainer Plate垫板Retainer Plate后模镶针Core Pin垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing 针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Noozzle Bulishing水口板导套Runner Stripper Pin定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel外廊Contour 吊环Safety Hoist Ring落单会议Kick-off 日期印Dating Insert装卸孔Handing Hole 环保印Recycling Insert运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙导柱位Leader Pin Location产品名Part Name缩水Shrinkage下模镶件Core Block小镶件Sub-Insert上模小镶件Core Sub-Insert行位镶件Slide Insert压紧块（铲机）Jaw硬片（摩擦片）Wear Plate 气顶Air Poppet Valve 截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品编号Part No版本Rev上模镶件Cavity Block下模小镶件Core Sub-Insert行位Slide压条Gib扁顶Blade出模斜波Draft水口铁Runner Bar 手动滑块模具Hand Slide-In Type Mold上模水口铁Upper Runner Bar 回针板Backup下模水口铁Lower Runner Bar 合模Shutoff弹簧Spring水口钩针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Inter Lock锁模板Safty Bar‘O’令（密封圈）O’Ring喉塞Plug隔水片Baffrle波子螺丝（行为定位螺丝）斜顶Lifter控制开关Switch 空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑料模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer烙接线（夹水纹）Weldlin吸针Sucker Pin回针板Retainer Plate顶出板Knock-Out Plate回针Return Pin 电动安全开关Electrical-Safety Switch斜导柱Angle Pin 脱开Cut Of Position推板Stripper Plate 预先决定PreloadA’板A’PlateB’板B’Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate精磨Finished通框Through Window粘后模Stricking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling 缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib有托顶针Shoulder Ejector Pin顶针板导套Guided Ejector Bushing 针板导柱Guided Ejector Leader Pin 不干胶Adhesive Sticker线切割Wire-Cut电火花Edm抛光Polishing走不齐Short Shot 蚀纹Texture挂成品Part Hanging 探热针Thermocouple漏水Water Leakage 三打螺丝毫（限螺丝）Stripper Bolt刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模Injection Mold入水Gate试板Sampling倒圆Fillet顶棍Ejector顶白Stress Mark名称块表Title Block版本标识Revision Level材料清单Stock List 盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料Cold Slag压力Pressure 螺纹孔Tapping Hole 连接件Fitting粘前模Sticking Cav 替换镶件Interchangeable Mold Insert制定吨位的注塑机Specific Press水嘴接头Water Fitting斜导柱（斜边）Angle Pin 螺纹Eyebolt Thread分模面Parting Surface 倒扣Under-Cut披峰Flash 锁定位Lock缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive热流道Manifold型腔数Cav No模号Mold No回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint 楔子（铲机）Wedge高产量模量High Volume Running Mold剖面图Cross Section模具结构Mold Construction出模角Draft擦位Shut-Off(S/O)导套Bushing导向针Guide Pin胶料Material尺寸Dimension重要尺寸Critical Dimension 雕刻Engrave托司Pin。

模具专业术语-中英文对照

Female Die 母模（凹模） Binder Plate 压板
Flask 上箱
Upper Mold Plate 上模板 Blank Holder 防皱压板 Floating Punch 浮动冲头
Lower Mold Plate 下模板 Blanking Die 落料冲头 Gate 浇口
Die Pad 下垫板
Parting Line 分模线
滑块板
Upper Holder Block 上压 Ejector Guide Pin 顶出 Parting Lock Set 合模定
块
导梢
位器
Upper Mid Plate 上中间 Ejector Leader Bush 顶 Pass Guide 穴型导板
板
出导梢衬套
Die Button 冲模母模
Locating Center Punch
定位中心冲头
Die Clamper 夹模器
Locating Pilot Pin 定位
导梢
Die Fastener 模具固定用 Locating Ring 定位环
零件
Die Holder 母模固定板 Lock Block 压块
Roller 滚轴
Located Pin 定位销
Diaphragm Gate 盘形浇口 Knockout Bar 脱模杵
Outer Bush 外导套
Die Approach 模头料道 Land 合模平坦面
Punch 冲头
Die Bed 型底
Land Area 合模面
Insert 入块（嵌入件） Deburring Punch 压毛边冲子 Groove Punch 压线冲子
Isoheight Sleeve 等高套 Cold Punched Nut 冷冲螺 Inlay Bush 嵌入衬套

模具术语中英文翻译

模具术语中英文翻译assembling mould装配铸型baked mould干型bar mould多穴压模big-end-up mould上大下小钢锭模black mould of rice 黑变病blank mould turnover 雏型模翻转blowing mould吹模blue mould of citrus 柑桔青霉病cap mould压顶线脚car type mould conveyor 小车式铸型输送机?case mould plaster 母模用石膏centrifugal casting mould离心铸造铸型?ceramic mould casting 陶瓷模注法channel mould槽模chill mould冷铸型(模)close mould封闭铸型close mould(铸造用) 合箱closed mould闭式模; 闭式压模cold-punching mould冷冲模collapsible mould分室模composite ceramic mould复合陶瓷型composite mould casting 复合型铸造copper mould base 铜模底copper mould wall 铜坩埚壁corrugated mould波形铸模cover mould压缝线脚covered floor mould盖箱地面铸型cylinder mould machine 圆网造纸机double-mould-broad ridging plough 双壁起垄犁?draw mould薄壁模子driel mould干型drip mould滴水线脚dry sand mould干型ear mould耳模electric pole mould hanger 电杆模型吊架?end mould端模Erical mould可压锭模; 挤压锭模evacuated mould空腔模face mould面模fall wheat snow mould冬小麦雪霉病falling mould曲型线条female mould阴模fixed mould固定模flaskless mould无箱铸型floating-point mould浮点模型floor mould地铸模fluted mould波形模foam sponge mould泡沫胶硫化模footed mould压印底圈的模型forging mould锻模front mould前模full-mould casting process 实型铸造?gang mould成组模; 成组模板garden mould园土get in the mould垫平铸型glass mould玻璃型; 玻璃铸型glass mould diode 玻璃模二极管graphite mould石墨型grass mould腐草土gray mould灰霉green mould绿霉病green mould of citrus 柑桔绿霉病ground mould地面铸型; 堆土木模gypsum mould石膏型hair mould毛霉hair mould sprout 毛霉芽half mould半型hoist for mould board carrier 模板车升降机?hump mould压坯用阳模ice mould冰铸ingot mould钢锭模; 铸锭模; 铸锭型; 锭模?ingot mould milling machine 钢锭模铣床?ingot slab mould扁钢锭模insulating mould coating 隔热涂料integral mould整模型invested mould熔模铸型iron mould铁锈迹leaf mould叶霉; 腐叶土loam mould泥型lower mould half 下模; 凹模male mould凸模; 阳模master mould母型; 原模mismatch in mould铸型错箱mould印模; 模; 模板; 模具; 模筛样板; 模塑; 模子; 成型模具; 圆网; 造型模板; 塑模; 霉; 霉病; 霉菌; 纸型mould addition 钢锭模添加剂mould and die milling machine 模具铣床mould assembling 合箱mould assembling and closing 铸型合箱mould assembly 合型mould blower 吹型机mould board 造型板; 样板mould boardless plough 无壁犁mould buggy 钢锭模车mould case 模制壳mould clamp 卡具mould clamps 模型紧固夹mould cleaner 模具清洁剂mould closer 合箱机; 合箱装置mould coating material 钢锭模涂料mould core 模芯mould cover 腐殖质层mould cure 模塑硫化; 模型硫化mould dam aged sweet potato poisoning 黑斑甘薯中毒?mould dimension 铸型尺寸mould drag 下半箱mould drying 铸型烘干mould efficiency 模塑效率mould emptier 脱模机构mould erosion 铸型冲蚀mould facing 涂料mould fitter 合箱工mould flat gauge 样板mould form 模型型腔mould fungus 霉菌mould growth test 长霉试验mould half 半型mould hardness 铸型硬度mould impression 模型内腔; 模型型腔; 模穴mould in a snap flask 无箱造型?mould in the pit 地坑造型mould inoculation 型内孕育mould jacket 型套mould kernel 模芯mould life 模型寿命mould lifting 铸型起模mould lining 坩埚衬里mould loft 放样间mould loft floor 放样台mould lofter 放样工; 放样工人?mould loftsman 放样工; 放样工人mould machine 模塑机mould machine of cereal seed selection 谷物选种机?mould mark 模缝条痕mould matrix cathode 模制阴极mould oil 脱模油mould on end 垂直分型造型mould pig iron 型铁mould plaster 模型用石膏mould plate 模型板mould plunger 阳模mould plunger force plug 凸模mould preparation bay 钢锭模准备跨mould press 模压机mould pressing 旋压成形mould proofing 防霉mould rains 梅雨mould release 分型粉mould relese 脱模mould rollover unit 翻箱装置mould sand 型砂mould setting-and-stripping bay 钢锭模准备和脱锭跨?mould shift 错箱mould shrinkage 模内收缩; 模压收缩; 脱模后的收缩mould splits 模组分mould stripping 铸型起模; 拆模?mould susceptibility 感霉性mould test chamber 霉菌试验箱mould train 模组mould turnover 翻箱mould unloading 出模; 脱模; 卸模?mould veining 铸型裂纹mould vibrator 模板振动器mould vulcanization 模塑硫化mould wash 脱模涂料mould wash mixer 涂料搅拌机multiple cavity mould多型腔铸型; 多巢模multiple mould多件石膏模multiple-part mould多箱铸型needle mould针模one-piece mould整体铸型open bottom mould底开式钢锭模open mould明浇铸型; 敞口铸型open sand mould明浇砂型optical instrument mould and fog auto-detector 光学仪器霉雾自动检测仪ornamental mould艺术造型pallet conveyer mould machine 滑板输送式造型机paper mould纸型paste mould衬碳模paste mould ware 衬碳模成形的制品?peat mould泥炭土permanent mould永久铸型plural mould operation 多模操作?porous mould多孔模型positive mould阳模; 阳压模press mould压模press mould ware 模压器皿pressing mould压模process of unconventional heat treatment of mould模具非常规热处理工艺quadrant mould四开木压条real mould实模型rectal suppository mould肛门栓剂模refractory shell mould耐火材料壳型removal of the mould拆模reverse mould倒模; 倒型revesing permanent mould双面金属型ring mould瓶颈模ring-shaped mould环型铸模risk of mould发霉险roast sand mould干砂型rubber mould橡胶皮模running mould模筛样板; 模饰样板saccharifying mould糖化霉sealing of a mould铸型密封section mould型模sectional mould镶合砂型semi-automatic mould半自动模; 半自动塑模semi-chilled mould casting 半金属型铸造; 半冷模铸造?semi-permanent mould半永久型; 半永久性模semiclosed top mould半封顶锭模shell mould machine 壳型造型机shiftable mould-board 可拆换的刀片sign mould符号模型single cavity mould整体铸型single mould单件模型skin dried mould面干铸型skin drying mould表干型sleeper steel mould轨枕钢模slime mould粘菌slip flask mould脱箱铸型snap flask mould活箱造型; 无箱铸型?snapflask mould脱箱造型snow mould雪霉病; 雪疫病soap mould皂模。

模具专业术语中英文对照

普通话
英语
普通话注塑樹脂材料
等級/類型
英语 Injection Resin Material Grade Dry Not Dried Enough Shrinkage Full Shot Density Temp Cont Unit Thermo Plastic Thermo Set Silver Line Flow Mark Weld Line Burr Sink Mark Burn Mark Short Shot Gloss Not Enough Bloe Hole Sticking Bending Warpage Uneven Gloss Black Spot Damage White Mark Hair Flash Scrtach Oil Dirt Crack Deform Parting Lock Gate Pin Gate Side Gate Submarine Gate
Update: 2007/11/23 第 1 页，共 1 页
模具专业术语中英文对照
普通话模具模胚分模線母模側公模側模板嵌件滑抉板
滑抉固定板
英语 Mold Mold Base Parting Line Cavity Side Core Side Mold Plate Insert Slider Wear Plate Angular Ejector Back Plate
定位机构 Inter Lock Eye Bolt 吊圏日期轉印 Date Mark Cavity 前模 Core 后模 Core Pin 型芯出模編号 Cavity Number Cooling Channel 冷却管 Hose Nipple 水嘴 Baffle 冷却棒 Heat Pipe 加熱管 O Ring O形圏 Air Vent 逃気孔 Dowel Pin 銷針銑床加工 Milling Machining 放電加工 EDM Machining Wire Cutting 線切割加工磨床加工 Grinding 孔位加工 Drilling Deburring 細加工省模加工 Polishing Fitting 配模 Shim 塞規 EDM Master 銅公筋骨加工 Rib Machining 脱模斜度 Draft Angle Under Cut 倒扣 Steel 鋼材 Texture 咬花彫刻加工 Engraving 電鍍加工 Electro Plating Hardening 熱処理氮化処理 Nitriding 表面処理 Surface Hardness 内六角螺釘 Allen Bolt Hot Runner 熱流道熱流道結构 Manifold Hot Tip 熱嘴

模具术语中英文对照

模具术语中英文对照模具(Mold) - A shaped cavity or matrix into which molten or uncured material is poured so thatupon solidification it will take on the shape of the cavity.注射模(Injection mold) - A molding cavity created by injecting material into a mold via a runner system.常用于塑料件注塑。

压铸模(Die casting mold) - A metal mold created for die casting processes, usually zinc, copper or aluminum based alloys.充型范(Pattern) - A full sized model of the desired casting, used to create the mold cavity in processes like sand casting.冒口(Sprue) - The primary vertical channel through which liquid material is poured into mold cavities.冒口通过主要供料道向模板腔内引入熔融金属。

气孔(Vent) - A small channel allowing the gases formed (by vaporization,chemical reaction etc.) to escape from mold cavity.用来排出模具腔内气体的小通道。

流道(Gate) - The channel that conveys molten metal from the sprue into the mold cavity.将熔融金属从主流道(冒口)引入模腔的小槽道。

模具中英对照

模具中英对照模具是一种用来制造复杂形状的工具，广泛应用于汽车、航空、电子、医疗等领域。

在国际贸易中，模具领域是一个重要的行业，涉及到的技术术语和行业术语繁多，因此，建立起一个模具中英对照的文档对于学习和应用模具领域具有重要的意义。

下面我们将列出一些常见的模具术语及其中英对照：1. 模具设计：mould design2. 模具制造：mould making3.模具材料：mould material4. 模具钢：mould steel5. 模具试样：mould trial sample6. 模具寿命：mould life7. 塑料注塑模具：plastic injection mould8. 金属冲压模具：metal stampingmould9. 模具零件：mould parts10. 设计参数：design parameter11. 模具尺寸：mould dimension12. 模具重量：mould weight13. 模具结构：mould structure14. 成型工艺：forming process15. 模具表面处理：mould surface treatment16. 冷却系统：cooling system17. 模具加工：mould machining18.精度控制：precision control19. 模具维护：mould maintenance20. 模具修复：mould repair随着模具行业的发展，中英对照文档需要不断地进行更新和完善。

在实际应用中，我们需要根据需求来确定需要掌握的技术和行业术语，并及时查阅相关的中英对照文档，以便更好地理解和使用模具技术。

除了上述列出的术语，模具领域还涉及到很多具有专业性的技术术语和行业术语，例如模具热处理、模具注塑成型、模具表面处理等方面的专业术语。

因此，掌握和应用模具技术需要具备较高的专业素养和知识储备，这需要我们持续地学习、实践和总结。

模具常用专业术语中英文对照

模具常用专业术语中英文对照塑料模具常用专业术语中英文对照模胚（架）：mold base 三板模（细水口）：3-plate mold二板模（大水口）：2-plate 定位圈（法栏）locating ring 浇口套（唧嘴）sprue bushing热流道：hot runner,hot manifold面板:cavity adaptor plate 水口板：runner stripper plate上模板（A板）:cavity plate 下模板（B板）:core plate 上内模（型腔＼母模＼凹模）：cavity insert下内模（型芯＼公模＼凸模）：core insert推板：stripper plate模脚（方铁）spacer plate 顶针板：ejector retainner plate托板(顶针底板)：support plat垃圾钉：stop pin撑头: support pillar底板：core adaptor plate 推杆：push bar顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin回针：push bake pin导柱：leader pin/guide pin 导套：bushing/guide bushing中托司（顶针板导套）：shoulder guide bushing中托边(顶针板导柱)：guide pin滑块（行位）：slide波子弹弓（定位珠）：ballcatch耐磨板/油板：wedge wear压条：plate斜导边（斜导柱）：angle压座/铲鸡：wedge斜顶：angle from pin斜顶杆：angle ejector rod 缩呵：movable core,return core core puller尼龙拉勾（扣机）：nylon latch lock栓打螺丝：S.H.S.B镶针：pin喉塞: pipe plug锁模块：lock plate挡板：stop plate螺丝：screw推板：stripper plate斜顶：lifterplate塑胶管：plastic tube快速接头：jiffy quick connector plug/socker mold内模管位：core/cavity inter-lockflash(塑件)毛边电极(铜公)：copper electrode五金模具常用专业术语中英文对照cutting die, blanking die冲progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling 线拉伸engraving, to engrave刻印top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate 底板（下托板）stripping plate 脱料板（表里打）outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板上模座upper die set成型公form punch脱料板stripper垫板subplate/backupplate下模座die plate垫脚parallel托板mounting plate顶料销kick off初始管位first start pin带肩螺丝shoulder screw两用销lifter pin弹簧护套spring cage拔牙螺丝jack screw侧冲组件cam section导正装置guide equipment 漏废料孔slug hole 刀口trim line 入子insert护套bushing 整形公restrike forming punch止挡板stop plate 挂台head扣位pocket of head 导柱guide post导套guide bushing 油嘴oil nipple接刀口mismatch/cookie bites限位块stop block挡块stopper浮块lifter压块keeper靠块heel对正块alignment block闭合高度shut hight上夹板/固定座holder/retainer下模座lower die set 成刑母公forming die 码模槽mounting slot 球锁紧固定座ball-lock 导尺rail送料板rail plate倒角chamfer销钉dowel尖角sharp --angle普通弹簧coil spring 镶件insert插针pilot pin顶杆lifter bolt起吊孔handing hole 垫片shim/wear-plate 键槽key slot沉孔counter hole导正块thrust block。

最全模具行业术语英文翻译

ball catch
喉塞: pipe plug
流道平衡:runner balance
斜顶杆：
angle ejector rod
热流道板：
hot manifold
xxxx：
parting locks
活动臂：
lever arm
发热管：
cartridge heater
复位键、提前回杆：
early return bar
强度不够：
insufficient rigidity
托板：
support plate
均匀冷却：
even cooling
管钉：
dowel pin
扣模：
sticking
公差：
tolorance
开模槽：
ply bar scot
热膨胀：
thero expansion
内模管位：
core/cavity inter-lock
保压
filing
锉刀xx
flange
凸缘
hand finishing
手工xx
gap
间隙
hemming
卷边加工
graphite
石墨
hobbing
滚齿加工
graphite contraction allowance
电极缩小余量
joggling
摇动加工
graphite holder
电极夹座
lapping
抛光/研磨xx
弹弓:die spring
中托司：
ejector guide bush
唧嘴直流: direct sprue gate
xx：
ejector guide pin

模具常用术语中英文对照

模具常用术语中英文对照模具常用术语中英文对照中文英文模芯Parting Core局部视图Partial View冷料# Cold Sllig线切割Wire E.D.M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Hapden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action中文英文加强筋Reinforcing三角撑Gusset柱子Bosse出模斜度Draft外廊Contour落单会议Kick-Off Meeting装卸孔Handl Ing Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap导柱位Leader Pin Location耐落胶Teflon Paste偏移量Offset水塞Water Line Plig撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoio凸缘、法兰Flange模具常用术语中英文对照中文英文方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer PlateCore Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Holst Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模具常用术语中英文对照中文英文模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate 水口铁Runner Bar上模水口铁Upper Runner Bar下模水口铁Lower Runner Bar弹簧Spring水口勾针Sprue Puller Pin顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch斜顶Lifter控制开关Switch模具常用术语中英文对照中文英文回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Holst Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade模具常用术语中英文对照中文英文出模斜波Draft手动滑块模具Hand Slide-In Txpe Mold回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Pulzer模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold 三板模3-Plat Mold分型面Parting Line司筒Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical Safety Switch 脱开Cut Of Positon预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam铕针Dowel钩槽Gib精磨Finished通框Through Window模具常用术语中英文对照中文英文粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage括花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模In Jection Mold入水Gate试板Sampling压力Pressure倒园Fillet顶棍Ejctor顶白(压痕) Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle Pin A板A'plateB板B'plate倒扣Under-Cut披峰Flash缩水Sink Mark模具常用术语中英文对照中文英文氮化Nitrided不规则四边形Trapeaold缩水Shrcnkage连续的Consecutive雕刻Engrave出模角Draft (草图）分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Hapden唧嘴Sprlie设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt 盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder9（液压缸）司筒Ejector Sleeve （脱模弹簧）导柱Leader Pin模具常用术语中英文对照中文英文冷料# Cold Sllig线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insfrt锁定位Lock楔子Wedge高产量模量High Volume Running Mold 剖面图Cross Sectlon模具结构Mold Construction模芯Parting Core局部视图Partlal View热流道Manifold热嘴Hot Nozzle型腔数Cav模号Mold No胶料Materlal尺寸Dimension重要尺寸Critical Dimension雕刻Engrave模具专业英语模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode。

模具术语(中英文对照)

AD-Diameter Thetreaddiameteratthecenterlineofthetread(EU);also:"T-Diameter"(GT)?AD直径：指胎面中心线直径（EU）。

又叫T直径（GT）Auto-lockEar ALugontheconeringusedtomountthemold/containerinthetophalfofa60“NRMAuto-lo ckpress.??导环上的突缘，用于和60“NRMAuto-lock硫化机上半部连接。

BeadRing Thetirebeadformingring(also:toering)?钢圈，也称toeringBeadRingRegister??钢圈配合：侧板上，和钢圈配合的平面及锥面BottomContainerPlate?模壳底座BottomContainerPlateLiftingLugsedforlifting.???分离钩：就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。

BreakerHookGuidePiece Ablockboltedtothebreakerhookthatalignsthetreadsegmentwithaslotinthebottomcontainerplate. ??分离钩导块：用螺栓固定在BreakerHook上，定位花纹块和模壳底座上槽的定位块。

BronzeWearPlates Anysacrificialmetalplateplacedunder,overorbehindacomponenttokeeptheco mponentsfromwearingoneachother(greasing)?青铜耐磨板(油润滑的)Casting Anun-machinedcastmetaltreadringorSegment?铸件：未加工的金属花纹圈或花纹块铸件。

CenteringRing Theringmountedonthebottompressplatentolocatethemold/containerconcentrically tothepress;also:"Pressregister"??定中环,也称“Pressregister”ClampRings Thebladderclampingassembly??胶囊夹盘ConeRinglso:"Actuatorring","Squeezering"(GT)??导环，也称"Actuatorring","Squeezering"Conicity?锥度Container?模壳,也叫mechanismContainerCavity??rea??DEVAMetal??DEVADowelPins Thepinsthatkeepthemoldhalvesandpartsaligned(containersorHKKmolds)?定位销：用来对模具的半模或零件定位的销（模壳或HKK模具）。

模具常用语中英文对照

种类中文名称英文名称中文名称英文名称模具种类连续模Progressive die 冲孔模Pierce die 机械手Transfer die 剪边模Trimming die 手动机械手Hand transfer die 下料模Blanking die 单工程模Single die 成形模Forming die 铸造结构模Cast die 折弯模Bending die 简易模Prototype die 围边模Flange die 铆合模Riveting die 拉伸模Draw die 复合模Compound die 快换模Changeable die工序类料带strip 料带图strip layout 工序process 冲导正孔pilot pierce 冲孔pierce 侧冲cam pierce 切边notch 切侧刃notch french 折弯bend 墩薄coin成形form 侧成形cam form 整形restrike 围边flange打凸米boss / dimple 打凸包emboss打字印stamp 打沙拉孔hourglass 面押coin burr 抽孔extrude hole 拍平flat 卷圆curl种类中文名称英文名称中文名称英文名称工序类旋转rotate 铆接rivet产品切边线trim line 铆螺母stake nut 切断cutoff 接刀口mismatch 料带带料处carrier tab 毛刺方向burr direction 压线groove 下料blanking模板类上托板top plate 下托板bottom plate 上垫脚upper parallel 下垫脚lower parallel 上模座upper die set 下模座lower die set 上垫板punch backup 下垫板lower backup 上夹板punch holder 下夹板die holder 上脱料板stripper 下模板die plate 冲头punch 凹模die零件类浮块lifter 浮料板lifter plate 成型公form punch 压料块pressure pad 切边冲头trim punch 刀口trim steel 沉头孔counter bore 冲孔入子button 顶针kick off / ejector 废料切断刀slug breaker 成型凹模forming die 整形公restrike punch 导尺rail 导尺顶杆lifter bolt 导料板rail plate 镶件/入子insert侧冲组件cam 滑块slide滑块上油槽oil groove 铲机driver码模槽mounting slot 储运块storage block 限位柱stop block 起吊孔handing hole 起吊环eyebolt 靠块heel脱料拉杆spool 模座导正块thrust heel种类中文名称英文名称中文名称英文名称零件类耐磨片wear plate 垫片shim压块keeper 初始管位first start pin键槽key slot 键key氮气弹簧nitrogen spring 螺旋弹簧coil spring聚氨酯弹簧urethane导柱guide post 导套guide bushing 插针pilot pin插针套pilot bushing 侧刃french传感器sensor 销dowel螺丝screw 拔牙jackscrew垫圈washer 盲销blind dowel压毛边冲头deburring punch 挡块stopping plate压线冲头groove punch 定位块location block字模冲头stamp punch 圆冲头round punch压筋冲头ribbon punch 气垫板air cushion plate 异形冲头special shape punch 气垫顶杆air-cushion eject-rod 切边冲头trimming punch 上压块pressure block加强筋冲头stiffening rib punch 弹簧箱spring box 定位板guide plate 弹簧箱顶杆spring-box eject-rod 压边圈binder 弹簧箱顶板spring-box eject-plate公差类公差tolerance 公差范围tolerance range 上公差upper tolerance 下公差lower tolerance 公差+/- 0.05 plus minus 0.05 形位公差图GD&T 平面度flatness 直线度Straightness 倾斜度angularity 垂直度perpendicularity 平行度parallelism 圆度roundness种类中文名称英文名称中文名称英文名称公圆柱度cylindricity 面轮廓度surface profile差类线轮廓度line profile 位置度true position 同轴度concentricity 对称度symmetry 圆跳动runout 全跳动total runout 尺寸dimension 角度值angle degree 尺寸全检报告dimensional layout 三次元尺寸报告CMM report冲床相关机械冲床mechanical press 油压机hydraulic press 吨位tonnage 行程stroke / travel 冲床上台面ram 冲床下台面bolster冲床台面布置图press layout 冲床上的快速对正QDC 冲床气垫air cushion 码仔stirrup 闭合高度shut height T型槽T-slot送料机feeder 送料高度feeding height工具卡尺caliper 千分尺micrometer 直尺ruler 高度尺height gage 丝攻screw tap 起子screwdriver 拨牙器jacker 扳手wrench风磨机hand grinder 油石oil stone加工类开料cutting material 钻drill (DR) 攻牙tap 铰ream铣mill 车lathe电脑锣NC mill 线切割wire cutting(W/C) 磨grind 刨planer电火花EDM 镭射laser cutting 倒角chamfer xx的精加工finish XX真空热处理vacuum heattreatment镀钛TD coating 退磁demagnetization 烧焊weld4.1.2 加工说明对照表：加工说明Machining Note注:有0.00的地方为数据填入处外导套OUTER GUIDE BUISHING 起吊杆HANDING PIN实数铣通MILL THRU 正反两面各铣TOP SIDE AND OPP SIDE MILLX:-￠0.00（氮气弹弓过孔，锣穿）单+0.00X:-￠0.00 (DR.THRU FOR GAS SPRING) S+0.00X:-￠0.00（氮气弹弓沉头，正面CNC单+0.00,锣深0.00.)X:-￠0.00 ( CNC C'BORE TOP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-￠0.00（氮气弹弓沉头，反面CNC单+0.00,锣深0.00.)X:-￠0.00 (CNC C'BORE OPP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-￠0.00（合销孔,铰)X:-￠0.00 (REAM FOR DOWEL)X:-￠0.00（合销孔,割)单+0.00X:-￠0.00 (W/C FOR DOWEL) S+0.00(正面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)(反面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP.0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-￠0.00（合销孔,钻穿)X:-￠0.00 (DR.THRU FOR DOWEL)X:-￠0.00（一般孔,钻穿)X:-￠0.00 (DR.THRU HL)X:-￠0.00（穿丝孔,钻穿)X:-￠0.00 (DR.THRU FOR WEDM S.H.)X:-￠0.00（漏油孔,钻穿) 按向视图加工X:-￠0.00 (DR.THRU FOR DRAIN HL) ACCORDING VIEW DRAWING TO MACHINING X:-（漏油槽,反面CNC单+0.00,锣深0.00)X:- (CNC POCKET OPP.SIDE FOR DRAIN, S+0.00, DP0.00)X:-￠0.00（基准孔,铰)X:-￠0.00 (REAM FOR DATUM HL)X:-￠0.00钻穿（螺丝过孔)内攻M0.00牙X:-￠0.00 (DR.THRU FOR CLEARANCE HL, TAP M0.00 THR)(正面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE)(反面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 OPP. SIDE)(侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00钻穿,反面攻深0.00,有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 OPP.SIDE, THR DP0.00)X:-M0.00钻穿,正面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP SIDE, THR DP0.00)X:-M0.00钻穿,正反面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,反面攻深0.00,有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 OPP. SIDE)X:-M0.00盲孔,正面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 TOP SIDE, THR DP0.00)X:-M0.00盲孔,正反面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00)X:-M0.00盲孔,侧面分中攻深0.00,组模自配X:-M0.00 BLIND HL, TAP DP0.00 ON EDGE FROM CENTER , DIE MAKER FIT) (侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00盲孔,侧面分中钻深0.00X:-M0.00 BLIND HL, DR. DP0.00 ON EDGE FROM CENTERX:-M0.00（拨牙螺丝孔，攻穿）X:-M0.00 TAP.THRU FOR JACK SCREWX:-￠0.00（塞打过孔,钻穿)X:-￠0.00 DR.THRU FOR SPOOLX:-￠0.00（弹弓过孔,钻穿)X:-￠0.00 DR.THRU FOR SPRINGX:-￠0.00（弹弓孔,反面沉深0.00)有效深0.00X:-￠0.00 (C'BORE FOR SPRING DP.0.00 OPP.SIDE, USED DP.0.00)X:-￠0.00（弹弓孔,正面沉深0.00)有效深0.00X:-￠0.00 (C'BORE FOR SPRING DP.0.00 TOP.SIDE, WORK DP.0.00)X:-（避空孔,锣穿)单+0.00X:- (POCKET THRU)S+0.00X:-（避空孔,正面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE)X:-（避空孔,反面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 OPP SIDE)X:-￠0.00（避空孔,反面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 OPP.SIDE)X:-￠0.00（避空孔,正面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 EDGE SIDE)X:-￠0.00（两用销过孔,割)单+0.00X:-￠0.00 (LIFTER PIN, W/C S+0.00)X:-（导尺避空,CNC单+0.00锣穿)X:- (POCKET FOR RAIL, CNC MILL THRU, S+0.00)X:-（导尺避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 TOP SIDE, S+0.00) X:-（导尺避空,反面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 OPP. SIDE, S+0.00) X:-（浮块避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR LIFTER, CNC MILL DP.0.00 TOP SIDE, S+0.00) X:-（浮块孔,割）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, W/C)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-（浮块孔,锣）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, MILL)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-￠0.00（顶针孔,钻穿)（反面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-￠0.00（顶针孔,钻穿)（正面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)X:-￠0.00（导柱（导套）孔,CNC锣)单+0.00X:-￠0.00 CNC MILL FOR GUIDE PIN(BUSHING) S+0.00X:-￠0.00（导柱（导套）孔,割)单+0.00X:-￠0.00 W/C FOR GUIDE PIN(BUSHING) S+0.00X:-M0.00*1.5(止付螺丝，正面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 TOP SIDE)X:-M0.00*1.5(止付螺丝，反面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 OPP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:-（INSERT HL, CNC MILL THRU S+0.00)(阴影部分正面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 TOP SIDE)(阴影部分反面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 OPP SIDE)X:-（入子孔,割）单+0.00X:-（INSERT HL, W/C S+0.00)(阴影部分扣位正面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 TOP SIDE)(阴影部分扣位反面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 OPP. SIDE)(正面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)注: 此处的沉头不能用C'BORE, 只有圆形的沉头才用C'BORE.(反面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:- (INSERT HL, CNC MILL THRU. S+0.00)X:-（入子孔,正面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 TOP SIDE)X:-（入子孔,反面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 OPP. SIDE)X:-￠0.00（插针孔,铰)单+0.00X:-￠0.00（REAM S+0.00 FOR PILOT PIN)X:-￠0.00（插针孔,割)单+0.00(正面沉头￠0.00*0.00深)X:-￠0.00（W/C FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-￠0.00（插针孔,钻穿)(正面沉头￠0.00*0.00深)X:-￠0.00（DR.THRU FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-（冲头过孔,割)单+0.00(正面避空，CNC单+0.00，锣深0.00)(阴影部分扣位正面锣深0.00)X:-（W/C S+0.00 FOR PUNCH CLEARANCE HL)(POCKET, CNC DP 0.00 S+0.00 TOP SIDE)(POCKET SHADE FOR HEAD, DP0.00 TOP SIDE)X:-（冲头过孔,锣穿)单+0.00(正面避空，CNC单+0.00，锣深0.00)X:-（MILL THRU.FOR PUNCH CLEARANCE HL)(POCKET DP0.00 CNC S+ TOP SIDE)X:-（异形冲孔,直x斜x,割)单+0.00(双线部分，割)单+0.00X:-（W/C FOR SPECIAL HL, 0.00 LAND 0.00 TAPER, S+0.00) (W/C PER DOUBLE LINE S+0.00)X:-（冲孔,直x斜x,割)单+0.00X:-（W/C FOR PIERCE DIE HL, 0.00 LAND 0.00 TAPER S+0.00) X:-（冲孔,割)单+0.00X:-（W/C FOR PIERCE DIE HL S+0.00)X:-￠0.00（冲孔漏屎,钻穿)X:-￠0.00 (DR. THRU FOR CHUTE)X:-（异形冲孔漏屎,CNC单+0.00,锣穿）X:-￠0.00 (MILL. THRU FOR SPECIAL CHUTE S+0.00)X:-（产品落料斜度，实数斜30º锣）X:-（MILL 30 TAPER FOR PART RAMP NO CLEARANCE)X:-（漏屎斜度，直x斜45º锣）X:-（MILL FOR CHUTE 0.00 LAND 45 TAPER)反面沉深底面留0.00MILL UNTIL DP正面沉深底面留MILL UNTIL DP五金模具单词总结模具种类:连续模progressive die机械手transfer die手动机械手hand transfer die单工程模single die/line die复合模compound die铆接模riveting die铸造结构模cast die能快换的模changeover die泡沫模pattern互换性:公差tolerance上公差upper tolerance下公差lower tolerance公差范围tolerance range公差+/- 0.05 plus minus 0.05形位公差图GD&T平面度flatness直线度straightness倾斜度angularity垂直度perpendicularity / squareness平行度parallelism圆度roundness / circularity圆柱度cylindricity面轮廓度surface profile线轮廓度line profile位置度true position同轴度concentricity对称度symmetry圆跳动runout全跳动total runout尺寸dimension角度angle degree全尺寸报告dimensional layout工艺性:料带strip料带图strip layout工序process冲导正孔pilot pierce冲孔pierce侧冲cam pierce切边notch成形后的切边trim切侧刃french trim / fringe trim 厚料切边后的精修边shave折弯bend墩薄coin折弯处压筋gusset成形form侧成形cam form整形restrike / rehit围边flange压线/压长条状筋ribbon打凸米boss / dimple打凸包emboss打字印stamp打沙拉孔hourglass面押coin burr抽孔extrude hole拍平flat / spanking包边hem edge压角cone张角flare切舌lance半剪knockout卷圆curl/热恶劣旋转rotate铆接rivet铆螺母stake nut切断cutoff接刀口mismatch料带带料处carrier tabs毛刺方向burr direction产品切边线trim line模具零件:模具die / tool上托板upper mounting plate 上垫脚upper parallel上模座upper die set上垫板punch backup上夹板punch holder止挡板traveling stop脱料板stripper下模板die plate下垫板die backup plate下模座lower die set下垫脚lower parallel上托板base mounting plate浮块lifter浮料板lifter plate成型公form punch压料块pressure pad切边冲头trim punch刀口trim steel刀口直身位land直5斜1 5mm Land 1 taper 刀口上沉头的深度die life 沉头counter bore冲头倒斜shear高低冲stagger punch球锁冲头ball-lock punch球锁座ball-lock retainer冲孔入子button顶针kick off / ejector废料切断刀slug breaker成型凹模form die整形公restrike form punch 导尺rail /stock guidance导尺顶杆lifter bolt导料板rail plate镶件/入子insert侧冲组件cam滑块slide滑块上油槽oil groove铲机driver码模槽mounting slot储运块storage block限位柱stop block起吊孔handing hole起吊环eyebolt模柄shank靠块heel摆块rocker bender脱料板拉杆stripper bolt模座导正块thrust耐磨片wear sheet耐磨板wear plate垫片shim两用销lifter pin初始管位first start pin内限位standoff压块keeper导柱导套压块keeper/ boss 键槽key slot键key氮气弹簧gas spring / nitrogen spring 氮气弹簧安装法兰mounting flange 氮气弹簧系统nitrogen manifold螺旋弹簧coil spring聚氨酯弹簧urethane弹簧套spring cage导柱guide post导套guide bushing插针pilot pin插针套pilot bushing插针通孔pilot through hole侧刃french误检装置misfeeder传感器sensor误检杆trigger油嘴oil nipple销针dowel pin螺丝screw牙thread拔牙jackscrew内六角螺钉socket head screw垫圈washer螺塞screw plug盲销blind dowel行程,走位stroke / travel吨位tonnage机械冲床mechanical press油压机hydraulic press冲床下台面bolster冲床上台面ram冲床台面布置图press layout冲床码模槽press mounting slot冲床气垫air cushion码模钳stirrup闭合高度shut height送料高度feeding height送料机feederT型槽T-slot避位clearance /pocket掏空pocket挂台head扣位pocket of head通气孔air vent hole漏油孔drain hole漏料孔slug hole基准孔datum hole通孔through hole穿丝孔first wire holeT型槽T-slot拔牙jackscrew摆块rocker bender闭合高度shut height避位clearance /pocket侧冲组件cam侧刃french插针pilot pin插针套pilot bushing插针通孔pilot through hole铲机driver沉头counter bore成型凹模form die成型公form punch冲床码模槽press mounting slot冲床气垫air cushion冲床上台面ram冲床台面布置图press layout冲床下台面bolster冲孔入子button冲头倒斜shear初始管位first start pin储运块storage block穿丝孔first wire hole传感器sensor弹簧套spring cage氮气弹簧gas spring / nitrogen spring 氮气弹簧安装法兰mounting flange氮气弹簧系统nitrogen manifold刀口trim steel刀口上沉头的深度die life刀口直身位land导尺rail /stock guidance导尺顶杆lifter bolt导料板rail plate导套guide bushing导柱guide post导柱导套压块keeper/ boss垫片shim垫圈washer顶针kick off / ejector吨位tonnage废料切断刀slug breaker浮块lifter浮料板lifter plate高低冲stagger punch挂台head滑块slide滑块上油槽oil groove机械冲床mechanical press基准孔datum hole键key键槽key slot聚氨酯弹簧urethane靠块heel扣位pocket of head两用销lifter pin漏料孔slug hole漏油孔drain hole螺塞screw plug螺丝screw螺旋弹簧coil spring码模槽mounting slot码模钳stirrup盲销blind dowel模柄shank模具die / tool模座导正块thrust内六角螺钉socket head screw 内限位standoff耐磨板wear plate耐磨片wear sheet起吊环eyebolt起吊孔handing hole切边冲头trim punch球锁冲头ball-lock punch球锁座ball-lock retainer上垫板punch backup上垫脚upper parallel上夹板punch holder上模座upper die set下托板base mounting plate 上托板upper mounting plate 送料高度feeding height送料机feeder掏空pocket通孔through hole通气孔air vent hole脱料板stripper脱料板拉杆stripper bolt误检杆trigger误检装置misfeeder下垫板die backup plate下垫脚lower parallel下模板die plate下模座lower die set限位柱stop block镶件/入子insert销针dowel pin行程,走位stroke / travel压块keeper压料块pressure pad牙thread油压机hydraulic press油嘴oil nipple整形公restrike form punch 直5斜1 5mm Land 1 taper 止挡板traveling stop机加工:开料cutting material钻drill (DR)攻牙tap铰ream铣mill车lathe电脑锣NC mill线切割wire cutting (W/C)磨grind刨planer电火花EDM镭射laser cutting倒角chamfer精加工finish XX真空热处理vacuum heat treatment镀钛TD coating退磁demagnetization烧焊weldG :40-M6BLIND HL,TAP DP18.00 OPP SIDE,THR DP18.00) 盲孔，反面攻深**G10:4-M30BLIND HL,TAP DP18.00 EDGE SIDE)盲孔，侧攻深**(%%c34.00*14.00 C'BORE DP14.00 TOP SIDE) 正面沉头多少×多少深G2 :24-%%c8.00(REAM FOR DOWEL WORK DP16.00 OPP SIDE,DR%%c6.00 HL)G2 :24-%%c8.00(合销,背铰深16.00,有效深,内钻%%C6.00通孔)G4 :3-%%c10.00(基准孔,背铰深20.00)背面锣25.00*25.00方形沉头，深1.00%%P0.01 (REAM FOR DATUM HL DP20.00,MILL25.00*25.00 OPP SIDE DP1.00%%P0.01)M:2-%%c15.00(弹簧孔,锣深33.00) (C'BORE OR SPRING DP33.00 TOP SIDE,WORK DP33.00)X :3-%%c32.00(导套孔,锣穿,单+0.01)(MILL THRU FOR GUIDE BUSHING S+0.01)G :2-M10盲孔,侧攻深30.00(有效深)(BLIND HL,TAP WORK DP30.00 EDGE SIDE)(沉头5.20%%P0.05深)(SLOT DP5.20%%P0.05 TOP SIDE)L :2-%%c8.000(合销,割)单+0.005 (W/C FOR DOWEL)S+0.005盲孔,攻深20.00(有效深) (BLIND HL,TAP DP20.00 TOP SIDE,THR DP20.00)(插针孔,割,单+0.01) (W/C S+0.01 FOR PILOT PIN)(避位孔,背锣9.80(有效深) (POCKET,MILL DP9.80 OPP SIDE WORK)(冲头过孔,锣穿) (MILL THRU FOR PUNCH CLEARANCE HL)(导柱孔,锣穿,单+0.005) (MILL FOR GUIDE PIN) S+0.005避位槽,背锣深19.00) (POCKET,MILL DP15.40 OPP SIDE)(背,沉头%%c14.00，掏深留11.00) (%%c14.00 C'BORE UNTIL DP14.00 OPP SIDE)下模刀口，实数割，直5斜1.5 （内钻%%C5.0穿丝孔）W/C S+0.00 TRIM STEEL,5.0LAND 1.5TAPER,(DR THRU%%c3.00 WEDM S.H)(MILL FOR INSERT DP30.0%%P0.01 S+0.01)(入子槽,锣深30.00%%p0.01,单+0.01)(氮气槽,背锣深4.00%%P0.1,单+0.1) (GAS SPRING MILL DP4.00 OPP SIDE)S+0.1按向视图加工ACCORDING VIEW DRAWING TO MACHINING试模材料:热扎板HRS (hot-roll steel)冷扎板CRS (cold-roll steel)不锈钢板Stainless steel镀锌板galvanized steel镀铝锌板galvalume steel热扎酸洗板HRPO steel (hot-rolled pickled and oiled steel)工具:卡尺caliper千分尺micrometer拨牙器jacker扳手wrench丝攻screw tap起子screwdriver码模钳stirrup设备/工具:3D Programmable CMM三次元检测仪3D CMM Beam Drilling Machine摇臂钻Bench Drilling Machine钻铣床Caliper卡尺CNC EDM电火花机CNC Machine Center加工中心CNCCNC Milling Machine数控铣床CNCCNC Planer Type Milling Machine龙门刨铣床Hardness Tester硬度计Height Gauge高度仪High Wire Cutting快走丝Hole Puncher 打孔机Horizontal surface grinder小水磨/卧式平面磨床Horizontal surface large grinder大水磨Lathe车床Measurement Surface Plate测量平台Metal Saw Machine锯床Milling Machine铣床Oil Press油压机Pin Gauge标准针规Plastic Injection Machine注塑机Point to Point CMM三次元测量仪Precision surface grinder精密手摇磨Press冲床Projector profile投影机Shear Press剪板机Slow Wire Cutting慢走丝Vertical Milling Machine卧式强力铣床扳手wrench拨牙器jacker卡尺caliper码模钳stirrup起子screwdriver千分尺micrometer丝攻screw tapCARVE 雕刻pothook 挂钩SPECIAL HL 异形孔漏斗 filler角铁 ANGLE IRON展开 expanding微调开关 INCHING SWITCH合叶 HINGE优力胶 RUBBER球锁垫板 LOCK WASHER双线边刀口,不倒角TRIM STEEL NEAR THE DOUBLE LINE NO CHAMFER滑块座:SLIDE SET机械:（engine type) liquid cooled, in-line, 4cylinder, carb (发动机型号)水冷，直列，四缸，化油器式(engine) compression ratio (发动机)压缩比(engine) displacement (发动机)排量(engine) fuel (发动机)燃料13-mode 13工况3rd gear 三档齿轮3-way seat 三向座椅4WD control device 四轮驱动控制装置4WD indicator switch 四轮驱动指示灯开关4WD lamp electrical connection 四轮驱动指示灯接线4WD switch 四轮驱动开关5th synchromesh assy. 五档同步器总成6PK belt 6PK 多楔驱动皮带A / C compressor assembly 空调压缩机总成A / C control assembly 空调控制装置A/C & heater assy. 空调加热器总成A/C blower 空调鼓风机A/C clutch 空调压缩机离合器A/C compressor MTG bracket 空调压缩机安装支架A/C control assy. 空调控制器A/C housing assy. 空调箱总成A/C low pressure switch 空调低压开关A/C mode select switch 空调状态选择开关abdomen performance criterion 腹部性能指标Abdominal Peak Force 腹部力峰值ABS 防抱死制动系统acceleration fuel system 加速系统acceleration running noise level 加速行驶噪声accelerator interlocking type 加速踏板联锁式accounting foundation 财政基础Actual cycle work 实际循环功Actual torso angle 实际躯干角adapter 连接器additional features 附加装置additional rule 附加法规adjust screw 调整螺钉adjuster cable 调整拉线adjuster plug 调整盖adjuster screw assy. 调整螺栓总成adjuster washer 调整棘片adjuster, diff. bearing 差速器轴承调整螺母Adjustment system 调节装置Administration and Registration Division 管理科Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts Which Can Be Fitted and/or Be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of These Prescriptions关于对轮式车辆、安装和/或用于轮式车辆的装备和部件采用统一条件并相互认可基于上述条件批准的协定书Agreement Regulations 协定法规air cleaner 空气滤清器air cleaner assy. 空气滤清器总成air cleaner cartridge 空气滤清器滤芯Air compressor 空压机air condition compressor 空调压缩机air direct 空气走向air filter 空气滤清器air flow 空气流向Air flow meter 空气流量计air jet 空气量孔air metering hole 空气量孔air path 气道Air Pressure of Tire 轮胎气压Air type 空气型air valve 空气阀air-cooled 风冷Aisles 通道Alcohol 酒精all bearing 球轴承alternater bracket 发动机支架alternator 交流发电机alterntor assembly 交流发电机总成alumininum-rim 铝合金钢圈alumininum opposed model 铝制对开式AM/FM cassette stereo radio 调幅/调频立体声收放机ambulance 救护车Amended by 修正文amount of exhaust emission 排气排放量Amplitude resolution 幅度分辨率Analogue magnetic recorder 模拟式磁记录仪ANALYZER 分析仪anchor plate, brake caliper 制动钳安装支架Anchorage 座椅固定装置Angle of divergence 偏离角Angle of rotation 旋转角angles drift off vertical line 指针偏离垂直线的角度Angular diameter of the retro-reflecting device 回复反射装置的角直径annex 附件Announcement 公告anti, shutdown screw 防不灭车调整螺钉Antilock Brake System 防抱死制动系统appendix 附录Applicable motor vehicle 适用机动车Applicable scope 适用范围applicant 申请人application 申请application for notification 认可申请书approval 认可arm, valve rocket 摇臂armature 转子总成armature shaft 电枢轴Arm-rests 靠手Article 条Article 1 第1条Asphalt solution 沥青溶剂Attached document 附署文件attached sheet 附表Attached Table 附表attaching location of seat belt anchorage 座椅安全带固定装置的固定位置attachment 附属文件Attendants onboard 车上值班人员automatic chock cover setting 自动阻风门盖调到automotive electric system 汽车电系automotive engine system 引擎系统automatic transmission 自动变速器，自动排挡变速箱Auxiliary Brake 辅助制动器Auxiliary Direction Indicator Lamps 辅助转向信号灯auxiliary spring 副簧Auxiliary Stop Lamp 辅助驻车灯axle case 桥壳axle case assy. 桥壳总成axle ratio 桥速比axle tube 桥管axle weight 轴重back angle level 靠背角水平仪back angle quadrant 靠背角量角器back pan 靠板back spring 回位弹簧backing plate 制动底板Backing sheet 衬背板Back-Up Light 倒车灯backup washer 支撑挡圈bail wire 卡紧环balance tube 平衡管ball 钢球ball bearing 球轴承ball joint assy. , upper 上球销总成ball valve 球阀ball valve, inlet 进油口球阀bar 拉杆barrier 障碍壁battery 蓄电池battery terminal 蓄电池接线柱bearing cap 轴承盖bearing cover, input shaft 输入轴轴承盖bearing, connecting rod 连杆轴承bearing, input shaft 输入轴轴承Bed for babies 婴儿床bell 带束层bench seat 长条座椅berived cap 轴承盖bezel assy. 框板总成bezel, cluster 表框be pilot 小批量产品blead door 混合风门bleeder screw 放气螺钉blower assy. 鼓风机总成blower motor 鼓风发电机blower resistor 鼓风机电阻blower switch 鼓风机开关body 车身,阀体body & liftgate assembly 车身和举升门总成body assy. 车身总成body block 人体模块body of A/C & heater 空调加热器壳体bolt 主缸连接螺栓bolt, connecting rod 连杆螺栓Booster 助力器boot 护罩BOSCH starter motor assembly “波舍”起动机总成bottle assy. , coolant recover 冷却液回收罐总成bottom houseing, fuel pump 燃油泵下壳体bottom housing, fuel tank 燃油箱下壳体bracket 支架bracket assy. , spring seat 弹簧座支架bracket, steering damper mounting 转向减振器支架brake alarm lamp 制动报警灯brake alarm lamp switch 制动报警灯开关Brake booster 制动助力器brake caliper 制动钳brake caliper assy. 制动钳总成brake caliper piston 制动钳活塞brake combination valve 制动组合阀brake disc 制动盘Brake drum 制动鼓brake fluid 刹车油Brake hose 制动软管brake lining 刹车来令brake line, LF 左前制动油管brake line, RF 右前制动油管brake oil flow 制动液流向brake paddle 制动踏板brake pedal 制动踏板Brake pipe 制动管brake shoes 刹车蹄片brake shoe 制动衬块Brake System 制动系Brake Systems for Tractors and Trailers 牵引车及挂车的制动装置Brake tester 制动器试验台brake valve 制动阀brake warning lamp 制动报警灯brake warning switch 制动报警开关Braking efficiency 制动效能braking force control system 制动控制装置Braking wheel 制动轮branch office 分署breaker 断电器bridge 过桥broadcasting vehicle 广播车brush 碳刷总成Buckle 带扣bulkhead 隔板Bulldozer 推土机bumper 保险杠Bumper element 保险杠构件bus transfer 车辆转移台bushing 衬套bushing, upper control arm 上控制臂衬套Business Place 业务场所bypass valve 旁通阀Cabinet Decision 内阁决议cable guide 拉线导向块cable-operated control system 液压式离合器系统Calibration factor of a data channel 数据通道校正系数calibration gas 标定气体calibration method 标定方法caliper assy. , front brake 前制动钳总成Camber 外倾camber angle 前轮外倾角camshaft 凸轮轴camshaft oil gallery 凸轮轴油道cap 加机油口盖cap assy. , power steering fluid reservoir 动力转向液油罐盖cap assy. , radiator 散热器盖总成cap screws 螺钉cap, connecting rod 连杆盖Capacity 容量,规格Capacity of the fuel tank 燃油箱容量capillary tube 毛细管carbon brushes & brush holder 电刷支架总成Carbon monoxide measuring instrument 一氧化碳分析仪Carburetor 化油器carburetor assy. 化油器总成carburetor bowl 化油器浮子室carburetor bowl vent system 化油器浮子室通风系统carburetor overhaul scheme 化油器分解图carburetor working scheme 化油器工作示意图carcase 胎体case runout (Max.) 差速器壳圆跳动（最大）Caster 后倾Catalyst 催化器category 类别cement and aggregate 水泥和混凝料Centreplane of occupant 乘员中心面Certified 经认证的Cetane number 十六烷值chain 驱动链chain drive 驱动链Channel amplitude class 幅度级通道Channel Frequency Class 频率级通道chassis 底盘chassis dynamometer 底盘测功机chassis shuttle 底盘平移台chassis number 底盘号Check and Maintenance 检查和保养check assy. , front door 前门限位器总成check assy. , rear door 后门限位器总成check ball 回止球check bracket 限位器支架check nut 限位器螺母check valve 单向阀check valve hole 回止阀孔check valve retainer 单向阀保持架check valve spring 单向阀弹簧check weight 回止块Chigi Circular No. 地技第…号Chigi No. 地技第…号Child Restraints 儿童约束装置chime module 蜂鸣器Chishin Circular No. 地审第…号Chishin No. 地审第…号chock heater 阻风门加热器总成chock plate 阻风门chock unloaded 阻风门连动装置choke 阻风门choke device 阻风装置choke unload mode 阻风门卸载状态cigarette lighter 点烟器circuit breaker, wiper/washer 刮水器/洗涤器电器断路器Circular 通告circular notice 通告clamp 卡圈Clamp ring type 锁紧圈式Cleaning efficiency 清洗效率Cleaning period 清洗周期clearance 最小离地间隙Clearance Lamp 示廓灯clinder head 气缸盖clip 卡子cluster housing 组合仪表壳Clutch system 离合器clutch assembly 离合器总成clutch control device 离合器控制装置clutch disc,clutch 离合器片clutch housing 离合器壳clutch master cylinder 离合器主缸clutch working cylinder 离合器工作缸Coating 涂层Code No. 型号Code of Federal Regulations 美国联邦法规总览Coefficient of luminous intensity (CIL) 亮度系数coil spring 圈状弹簧cold air 冷空气cold cranking voltage(min.) 最小冷启动电压collapsible spacer 可压缩隔垫collector 拼装台colorimeter 色度计coloured-light unit 有色灯光组column assy. 转向管柱总成combination brake switch and proporting 组合阀combined lamp 复合灯combined pump 复合泵combined pump diaphragm 复合泵膜片combined pump diaphragm rod 复合泵膜片杆combined pump lifter link 复合泵举升拉杆combined pump move direct 复合泵运动方向Combustion Chamber 燃烧室commutator 换向器compensate opening 补偿孔completion inspection certificate 终了检验证书Completion of notification 完成认可compressor 压缩机compression (both) 气环槽（两个）compression ignition type 压燃式Compression ratio 压缩比concrete mixer truck 混凝土搅拌车condenser 冷凝器condenser assy. 冷凝器总成conduit pipe 导管cone , diff. side bearing 差速器轴承，内圈带滚子cone, pinion front bearing 主动齿轮前轴承内圈带滚子cone, pinion rear bearing 主动齿轮后轴承内圈带滚子Confirmor 确认者connecting rod 连接杆connecting link 连接杆connecting rod journal diameter 连杆轴径connecting rod journal width 连杆轴径宽度connecting rod throttle 连杆喷油孔connector 连接器connector of service valve 维修阀接口Constant speed 等速construction and device 结构和装置control & tube assy. , hyd clutch 离合器工作缸和油管总成Control System 操纵系control valve 控制阀阀门control valve model 控制阀型式control valve seat 控制阀阀座convex plate 凸台cooling fan 冷却风扇cooling system 冷却系统Cornering Lamp 转弯灯corrected 修正的cotter 开口销counter 5th gear 中间轴五档齿轮counter shaft 中间轴coupled condition 连接状态Coupling Device 牵引装置cover 端盖cover & plate assy. 离合器盖及压盘总成cover assy. , air cleaner 空气滤清器盖总成cover, gear 侧盖cover, heater air 空气加热罩cover, rear axle case 后桥壳盖crane vehicle 起重车crankcase 曲轴箱crankshaft 曲轴crankshaft gear 曲轴齿轮crankshaft & connecting 曲轴连杆机构crankshaft oil gallery 曲轴油道crankshaft sprocket 轴承链轮critical flow 临界流Cross sensitivity of a linear transducer 线性传感器的横向灵敏度Crush distance 压碎距离Crush rate 压碎速率Crush Strength 压碎强度Cumulative time 累计时间cup 皮碗cup, diff. side bearing 差速器轴承外圈cup, pinion front bearing 主动齿轮前轴承外圈cup, pinion rear bearing 主动齿轮后轴承外圈Cut-off 明暗截止线cycle 冲程cyclinder head cover 气门室罩Cylinder 气缸cylinder block 汽缸体cylinder body 缸体Cylinder bore 缸径cylinder head 汽缸盖cylinder head cover 气门室罩cylinder number 气缸数cylinder working order(clockwise) 气缸工作顺序（顺时针）damper 转向减振器dangerous article 危险物darkroom 暗室Data channel 数据通道Data Processing 数据处理Date of notification 认可日期Deceleration of the structure 地板减速度Definitions 定义Definitions 术语deflection 偏移defroster 除霜器dehydrator 储液器和干燥器。

模具常用术语中英文对照

模具常用术语中英文对照模芯Parting Core局部视图Partial View冷料# Cold Slag线切割Wire E.D.M轮廊Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leaderd Pin镶件Mold Insert加硬Harden唧嘴Sprue设计筒图Design Preliminary名称块表Title Block版本标识Revision Level材料清单Stock List制模Build Mold手动滑块Hand Slide漏水测试Leak Test流道排气Runner Vents抛光Draw Polish侧抽芯Side Action加强筋Reinforcing三角撑Gusset柱子Bossed出模斜度Draft外廊Contour落单会议Kick-Off Meeting 装卸孔Handling Hole运输安全带Moldstrap码模槽Clamp Slot撑头Support Pillar螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位Leader Pin Location耐落胶Teflon Paste偏移量Offset水塞Water Line Plug撬模脚Ppy Slot重新加工Reworked配件Components补偿Compensation平面度Parallel倒角Chamfer模胚Mold Base热嘴Hotnozzle火花机Edm熔接线Weildline压机Press晒纹Texturing梯形Trapezoid凸缘、法兰Flange方铁Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate 垫板Retainer Plate后模镶针Core Pin拉圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速项Accelerated Ejector客户Client产品名Part Name产品编号Part No缩水Shrinkage版本Rev模胚Mold Base下模镶件Core Block上模镶件Cavity Block小镶件Sub-Insert下模小镶件Core Sub-Insert上模小镶件Cavity Sub-Insert 行位Slide行位镶件Slide Insert压条Gib压紧块（铲机）Jaw硬片（摩擦片）Wear Plate水口铁Runner Bar上模水口铁Upper Runner Bar 下模水口铁Lower Runner Bar 弹簧Spring水口勾针Sprue Puller Pin 顶针Ejector Pin撑头Support Pillar直身锁Side Lock斜度锁Interlock锁模板Safety Bar‘O’令（密封圈）O'Ring 喉塞Plug隔水片Baffle波子螺丝（行位定位螺丝）Ball-Catch 斜顶Lifter控制开关Switch回针Return Pin斜导柱Angle Pin推板Stripper PlateA’板A'PlateB’板B'Plate方铁（垫铁）Spacer Block顶针板Ejector Plate顶针底板Ejector Retainer Plate垫板Retainer Plate垃圾钉Stop Pin有托顶针Shoulder Ejector Pin顶针板导套Guided Ejection Bushing 针板导柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing 水口板导套Runner Stripper Plate Bushing 定位圈（法兰）Locating Ring管钉（定位销）Dowel Pin管状管钉Tubular Dowel吊环Safety Hoist Ring日期印Dating Insert环保印Recycling Insert气顶Air Poppet Valve截水口镶件Runner Shut-Off Insert早回Early Ejector Return加速顶Accelerated Ejector扁顶Blade出模斜波Draft手动滑块模具Hand Slide-In Type Mold 回针板Backup合模Shutoff空隙槽Clearance Slot导柱及导套Leader Pin Bushing水口拉钩Spuer Puller模框镶件Pocket Insert成型热固性塑胶模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve垫圈Washer熔接线（夹水纹）Weldline吸针Sucker Pin回针板Retainer Plate顶出板Knock -Out Plate电动安全开关Electrical-Safety Switch 脱开Cut Of Position预先决定Preload缓冲器Bumper衬垫Cushion公差Tolerance突然性动作Slam销针Dowel钩槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夹水纹Weld Line变形Warpage走水不平均Filling Uneven走不齐Short Shot挂成品Part Hanging漏水Water Leakage刮花（擦伤）Galling漏电Ele Leakage困气Air Trapping温度Temperature注塑模※※※※ction Mold 入水Gate试板Sampling压力Pressure倒圆Fillet顶棍Ejector顶白Stress Mark粘前模Sticking Cav名称块表Title Block版本标识Revision Level材料清单Stock List斜导柱（斜边）Angle PinA板A'plateB板B'plate倒扣Under-Cut披峰Flash缩水Sink Mark氮化Nitride不规则四边形Trapezoid缩水Shrinkage连续的Consecutive雕刻Engrave出模角Draft分模面Parting Surface擦位Shut-Off(S/0)导套Bushing回针Return Pin加硬Harden唧嘴Sprue设计筒图Design Preliminary丝印Silkprint不干胶Adhesive Sticker导向针Guide Din公差Tolerance线切割Wire-Cut电火花Edm抛光Polishing蚀纹Texture探热针Thermocouple三打螺丝毫（限螺丝）Stripper Bolt盖板Cover Plate齿轮Gear油唧Hydraulic Cylinder司筒Ejector Sleeve导柱Leader Pin冷料# Cold Slag线切割Wire E.D.M.轮廓Contour螺纹孔Tapping Hole连接件Fittings斜针Angle Pin接合Engage替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press水嘴接头Water Fittings螺纹Eyebolt Thread回针Stop Pin二级顶出针Sub-Leader Pin镶件Mold Insert锁定位Lock楔子(铲鸡) Wedge高产量模量High V olume Running Mold剖面图Cross Section模具结构Mold Construction 模芯Parting Core局部视图Partial View热流道Manifold热嘴Hot Nozzle型腔数Cav No模号Mold No胶料Material尺寸Dimension重要尺寸Critical Dimension 雕刻Engrave。

模具术语(中英文对照)

精心整理AD-Diameter Thetreaddiameteratthecenterlineofthetread(EU);also:"T-Diameter"(GT)?AD 直径：指胎面中心线直径（EU ）。

又叫T 直径（GT ）Auto-lockEar ALugontheconeringusedtomountthemold/containerinthetophalfofa60“NRMAuto -lo ckpress.??导环上的突缘，用于和60“NRMAuto -lock 硫化机上半部连接。

BeadRing Thetirebeadformingring(also:toering)???????分离钩：座帮助花纹块和轮胎进行分离。

BreakerHookGuidePieceAblockboltedtothebreakerhookthatalignsthetreadsegmentwithaslotinthebottomcontainerplate. ??分离钩导块：用螺栓固定在BreakerHook 上，定位花纹块和模壳底座上槽的定位块。

CenteringRing Theringmountedonthebottompressplatentolocatethemold/containerconcentrically tothepress;also:"Pressregister"??定中环,也称“Pressregister”ClampRings Thebladderclampingassembly??胶囊夹盘ConeRing Theouterringthattransformstheaxialmovementofthepressinaradialoneofthesegments;a??Conicity?锥度?模壳,??rea????DEVADowelPins Thepinsthatkeepthemoldhalvesandpartsaligned(containersorHKKmolds)?定位销：用来对模具的半模或零件定位的销（模壳或HKK模具）。

模具常用语中英文对照

以下是30 个模具常用语的中英文对照：1.模具：mold2.模具设计：mold design3.模具制造：mold manufacturing4.模具加工：mold processing5.模具寿命：mold life6.模具维护：mold maintenance7.模具成本：mold cost8.模具材料：mold material9.模具结构：mold structure10.模具零件：mold part11.模具装配：mold assembly12.模具调试：mold debug13.模具成型：mold forming14.模具分型面：mold parting surface15.模具型腔：mold cavity16.模具型芯：mold core17.模具滑块：mold slider18.模具斜顶：mold lifter19.模具顶针：mold ejector pin20.模具冷却系统：mold cooling system21.模具浇注系统：mold gating system22.模具排气系统：mold venting system23.模具尺寸公差：mold dimensional tolerance24.模具表面粗糙度：mold surface roughness25.模具硬度：mold hardness26.模具钢：mold steel27.模具加工工艺：mold processing technology28.模具检测：mold inspection29.模具修改：mold modification30.模具报废：mold scrap。

模具术语中英文对照表

模具术语中英文对照表模具是制造行业中重要的零部件之一，不同的国家或地区对于模具的称呼和术语有着不同的表述。

下面是模具术语的中英文对照表，供大家参考。

一、模具结构及零部件1.凸模：punch/upper die2.凹模：die/lower die3.合页模：hinge die4.活动凸模：movable punch5.固定凸模：fixed punch6.活动凹模：movable die7.固定凹模：fixed die8.下座：bottom plate/bottom clamping plate9.定位销：locating pin10.定位套：locating sleeve/bushing11.导柱：guide pillar12.导套：guide bush13.顶杆：ejector rod/knockout rod14.顶针：ejector pin/knockout pin15.顶出板：ejector plate/knockout plate16.压簧：compression spring17.弹簧：tension spring18.滑块：slide block19.顶针板：ejector plate/knockout plate二、模具材料1.冷/热作模钢：cold/hot work die steel2.合金工具钢：alloy tool steel3.模具钢：mould steel4.不锈钢：stainless steel5.硬质合金：hard alloy/cemented carbide6.铝：aluminum7.铜：copper8.铜合金：copper alloy9.镁合金：magnesium alloy三、模具表面处理1.硬化：hardening2.淬火：quenching3.氮化：nitriding4.喷涂：spraying5.镀铬：chrome plating6.抛光：polishing7.喷砂：sandblasting四、模具制造工艺1.车削：turning2.铣削：milling3.磨削：grinding4.电火花加工：electric discharge machining (EDM)5.线割加工：wire-cut EDM6.钻孔：drilling7.铰孔：reaming8.螺纹加工：threading9.组装：assembly10.检验：inspection以上是模具术语的中英文对照表，本表可供参考，希望对有需要的读者有所帮助。

模具常用术语中英文对照

小镶件 Sub-Insert
下模小镶件 Core Sub-Insert
上模小镶件 Cavity Sub-Insert
行位 Slide
行位镶件 Slide Insert
压条 Gib
压紧块（铲机） Jaw
硬片（摩
螺纹 Eyebolt Thread
回针 Stop Pin
二级顶出针 Sub-Leaderd Pin
镶件 Mold Insfrt
三板模延伸式唧嘴 Extension Nozzle Bushing
水口板导套 Runner Stripper Plate Bushing
定位圈（法兰） Locating Ring
管钉（定位销） Dowel Pin
管状管钉 Tubular Dowel
吊环 Safety Holst Ring
盖板 Cover Plate
齿轮 Gear
油唧 Hydraulic Cylinder9（液压缸）
司筒 Ejector Sleeve （脱模弹簧）
导柱 Leader Pin
模具常用术语中英文对照
中文英文
冷料# Cold Sllig
线切割 Wire E.D.M.
模具常用术语中英文对照
中文英文
模芯 Parting Core
日期印 Dating Insert
环保印 Recycling Insert
气顶 Air Poppet Valve
截水口镶件 Runner Shut-Off Insert
早回 Early Ejector Return
加速顶 Accelerated Ejector
扁顶 Blade

模具常用术语中英文对照

模芯Parting Core 耐落胶Teflon Paste局部视图Partial View 偏移量Offset冷料Cold Slag 水塞Water Line Plug线切割Wire E.D.M 撬模脚Ppy Slot轮廓Contour 重新加工Reworked螺纹孔Tapping Hole 配件Components连接件Fittings 补偿Compensation斜针Angle Pin 平面度Parallel接合Engage 倒角Chamfer替换镶件Interchangeable Mold Inserts 模胚Mold Base指定吨位的注塑机Specific Press 热嘴Hotnozzle水嘴接头Water Fitting 火花机Edm螺纹Eyebolt Thread 熔接线Weildline回针Stop Pin 压机Press二级顶出针Sub-Leaderd Pin 嗮纹Texturing镶件Mold Insert 梯形Trapezoid加硬Harden 凸缘、法兰Flange唧嘴Sprue 方铁Spacer Block设计筒图Design Preliminary 顶针板Ejector Plate名称块表Title Block 顶针底板Ejector Retainer Plate版本标识Revision Level 垫板Retainer Plate材料清单Stock List 后模镶针Core Pin制模Build Mold 垃圾钉Stop Pin手动滑块Hand Slide 有托顶针Shoulder Ejector Pin漏水测试Leak Test 顶针板导套Guided Ejection Bushing流道排气Runner Vents 针板导柱Guided Ejection Leader Pin抛光Draw Polish 唧嘴Sprue Bushing侧抽芯Slide Action 三板模延伸式唧嘴Extension Noozzle Bulishing 加强筋Reinforcing 水口板导套Runner Stripper Pin三角撑Gusset 定位圈（法兰）Locating Ring柱子Bossed 管钉（定位销）Dowel Pin出模斜度Draft 管状管钉Tubular Dowel外廊Contour 吊环Safety Hoist Ring落单会议Kick-off 日期印Dating Insert装卸孔Handing Hole 环保印Recycling Insert运输安全带Moldstrap 气顶Air Poppet Valve码模槽Clamp Slot 截水口镶件Runner Shut-Off Insert撑头Support Pillar 早回Early Ejector Return螺牙1/2-13 Eye 1/2-13Tap 加速项Accelerated Ejector导柱位Leader Pin Location 客户Client产品名Part Name 产品编号Part No缩水Shrinkage 版本Rev下模镶件Core Block 上模镶件Cavity Block小镶件Sub-Insert 下模小镶件Core Sub-Insert上模小镶件Core Sub-Insert 行位Slide行位镶件Slide Insert 压条Gib压紧块（铲机）Jaw 扁顶Blade硬片（摩擦片）Wear Plate 出模斜波Draft水口铁Runner Bar 手动滑块模具Hand Slide-In Type Mold 上模水口铁Upper Runner Bar 回针板Backup下模水口铁Lower Runner Bar 合模Shutoff弹簧Spring 空隙槽Clearance Slot水口钩针Sprue Puller Pin 导柱及导套Leader Pin Bushing顶针Ejector Pin 水口拉钩Spuer Puller撑头Support Pillar 模框镶件Pocket Insert直身锁Side Lock 成型热固性塑料模具Thermoset Mold 斜度锁Inter Lock 三板模3-Plat Mold锁模板Safty Bar 分型面Parting Line‘O’令（密封圈）O’Ring 司筒Ejector Sleeve喉塞Plug 垫圈Washer隔水片Baffrle 烙接线（夹水纹）Weldlin波子螺丝（行为定位螺丝）吸针Sucker Pin斜顶Lifter 回针板Retainer Plate控制开关Switch 顶出板Knock-Out Plate回针Return Pin 电动安全开关Electrical-Safety Switch 斜导柱Angle Pin 脱开Cut Of Position推板Stripper Plate 预先决定PreloadA’板A’Plate 缓冲器BumperB’板B’Plate 衬垫Cushion方铁（垫铁）Spacer Block 公差Tolerance顶针板Ejector Plate 突然性动作Slam顶针底板Ejector Retainer Plate 销针Dowel垫板Retainer Plate 钩槽Gib精磨Finished 有托顶针Shoulder Ejector Pin通框Through Window 顶针板导套Guided Ejector Bushing粘后模Stricking Core 针板导柱Guided Ejector Leader Pin粘水口Sticking Sprue 不干胶Adhesive Sticker夹水纹Weld Line 线切割Wire-Cut变形Warpage 电火花Edm走水不平均Filling 抛光Polishing走不齐Short Shot 蚀纹Texture挂成品Part Hanging 探热针Thermocouple漏水Water Leakage 三打螺丝毫（限螺丝）Stripper Bolt 刮花（擦伤）Galling 盖板Cover Plate漏电Ele Leakage 齿轮Gear困气Air Trapping 油唧Hydraulic Cylinder温度Temperature 司筒Ejector Sleeve注塑模Injection Mold 导柱Leader Pin入水Gate 冷料Cold Slag试板Sampling 压力Pressure倒圆Fillet 螺纹孔Tapping Hole顶棍Ejector 连接件Fitting顶白Stress Mark 粘前模Sticking Cav名称块表Title Block 替换镶件Interchangeable Mold Insert版本标识Revision Level 制定吨位的注塑机Specific Press材料清单Stock List 水嘴接头Water Fitting斜导柱（斜边）Angle Pin 螺纹Eyebolt Thread分模面Parting Surface 倒扣Under-Cut披峰Flash 锁定位Lock缩水Sink Mark 楔子（铲机）Wedge氮化Nitride 高产量模量High Volume Running Mold 不规则四边形Trapezoid 剖面图Cross Section缩水Shrinkage 模具结构Mold Construction连续的Consecutive 出模角Draft热流道Manifold 擦位Shut-Off(S/O)型腔数Cav No 导套Bushing模号Mold No 导向针Guide Pin回针Return Pin 胶料Material加硬Harden 尺寸Dimension唧嘴Sprue 重要尺寸Critical Dimension设计筒图Design Preliminary 雕刻Engrave丝印Silkprint 托司EJ.Guide Pin。

模具术语中英文对照【大全】

上模：Upper Die上模座：Upper die holder下模：Lower die下模座：Lower die bottom环模：Holder die压料板：Pad安全护板：Safety Guard耐磨板：Wearplate吊耳：Hook插入式吊耳：Insert hook搬运固定板：Fix in Plates防呆装置：Fool Proofing快速定位：Quick Clamp安全侧销：Retainer pin sets(Safety) 保管垫块：Blocks平衡垫块：Balancer block停止垫块：Stoper block氮气缸：NiirogenSpring到底记号：Check Buttons镶块：Insert Block素材定位器：Nest Guide进退料支架：SKID Brackets脱料板：Stripper die顶料块：lift block零件详细：Parts detail检具：Checking Fixture气缸：Cylinder接头：Adapter(Augmture)快速接头：Quick Nipple三向接头：Three-Way Connector万向接头：Universal-Joint adapterL型快速接头：L JointT型快速接头：T Joint阀：Valve调速阀：Covernor Valve方向调节阀：Directional Control Valve 定位销：Location Pin开口销：Split Pin带头销：Pin with head固定销：Doweel Pin夹：Clamp管：Pipe连接管：Connector排气孔：Air Vent轴：Shaft连杆轴：Link shaft下模钢块：Lower Steel行程定位：Stroke end block 废料刀：Scrap cutter废料盒：Scrap Box定位键：locating key凸轮组件：Cam Unit凸轮滑动座：Cam Slide凸轮驱动座：Cam driver凸轮侧滑块：Cam side slide 切刀块：Cutter Nlock分块：Sectional Block导柱：Guide Post导套：Guide bush导柱组：Guide Post Set缓冲垫块：Cushion Plate挡板(块)：Baffle垫块：Plate垫圈：Washer焊接：Welding树脂：Resin消音器：Muffle螺帽：Nut有槽螺帽：Slotted Nut销规：Guage承盘：Retainer柱塞：Plunger端子箱：Cable connecting Box集头座：Connector Support内六角螺栓：SHC Screw内螺纹圆柱销：DOWEL PIN吊挂：Retainer Bolt弹簧导销：Spring Guide retainers 工法图：Die layout上模面：Upper die of plan view 下模面：Lower die of plan view 断面：Section冲头：Punch固定块：Fix Plate作用套管：Spool Retainer滚轮：Rubber roller衬套：Bushing冲头固定座：Retainer 盖板：Safety Guard托架：Bracket曲柄：Crank。