机械创新设计英文单词
机械设计类行业专用术语中英对照
机械设计类行业专用术语中英对照阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter 齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism 串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing 单万向联轴节single universal joint单位矢量unit vector当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等效动力学模型dynamically equivalent model等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心移动从动件radial reciprocating follower对心直动从动件radial (or in-line ) translating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分度圆reference circle; standard (cutting) pitch circle 分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交*带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle分析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket；sprocket-wheel；sprocket gear；chain wheel 联组V 带tight-up V belt联轴器coupling shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design; design for environment马耳他机构Geneva wheel Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product’s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价和决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing 球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy’s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham’s coupling 矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing 松边slack-side 顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding motion弹性联轴器elastic coupling flexible coupling弹性套柱销联轴器rubber-cushioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form特殊运动链special kinematic chain特性characteristics替代机构equivalent mechanism调节modulation, regulation调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing调心轴承self-aligning bearing调速speed governing调速电动机adjustable speed motors调速系统speed control system调压调速variable voltage control调速器regulator, governor铁磁流体密封ferrofluid seal停车阶段stopping phase停歇dwell同步带synchronous belt同步带传动synchronous belt drive凸的，凸面体convex凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling 图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling universal coupling外齿轮external gear弯曲应力beading stress弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement位移曲线displacement diagram位姿pose , position and orientation稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism 蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite系杆crank arm, planet carrier现场平衡field balancing向心轴承radial bearing向心力centrifugal force 相对速度relative velocity 相对运动relative motion相对间隙relative gap象限quadrant 橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion 修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear谐波传动harmonic driving谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism虚拟现实virtual reality虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; permissible stress悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure 压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring 液压无级变速hydraulic stepless speed changes 液压机构hydraulic mechanism一般化运动链generalized kinematic chain移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration应力图stress diagram应力—应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring 圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation运动粘度kenematic viscosity载荷load载荷—变形曲线load—deformation curve载荷—变形图load—deformation diagram窄V 带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator 直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact周节pitch周期性速度波动periodic speed fluctuation周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load轴向基本额定动载荷basic dynamic axial load rating轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link 主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair转速swiveling speed rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work 纵向重合度overlap contact ratio纵坐标ordinate组合机构combined mechanism 最少齿数minimum teeth number 最小向径minimum radius作用力applied force坐标系coordinate frame。
机械学英语
机械学英语
机械学（Mechanical Engineering）涉及广泛的工程领域，涵盖机械设计、制造、材料、热力学、控制等多个方面。
以下是一些常见的机械学英语术语及其解释：
1. Mechanical Engineering - 机械工程
2. Thermodynamics - 热力学
3. Fluid Mechanics - 流体力学
4. Mechanics - 力学
5. Materials Science - 材料科学
6. Manufacturing Processes - 制造工艺
7. Control Systems - 控制系统
8. Robotics - 机器人技术
9. Kinematics - 运动学
10. Dynamics - 动力学
11. Statics - 静力学
12. Heat Transfer - 热传导
13. Machine Design - 机械设计
14. CAD/CAM - 计算机辅助设计/计算机辅助制造
15. Vibration Analysis - 振动分析
16. Finite Element Analysis (FEA) - 有限元分析
17. Hydraulics - 液压学
18. Pneumatics - 气动学
19. Turbomachinery - 涡轮机械
20. Engineering Drawing - 工程制图
这些术语是在机械工程领域中常见的英语专业术语，涵盖了机械工程学科的各个方面。
深入学习这些术语可以帮助理解和掌握机械工程相关的知识和技术。
《机械创新设计》课程教学大纲
《机械创新设计》课程教学大纲一、课程名称中文名称：机械创新设计英文名称：Machinery Innovation Design二、课程代码11113103三、课程属性专业必修课四、学时数、学分数48（理论学时：44实验学时：4）、3学分五、适用专业四年制本科机械电子工程专业、机械设计制造及其自动化专业、机械工程专业。
六、编制者编制：唐剑兵七、编制日期2015年7月八、本课程的目的和任务本课程是本科机械设计制造及其自动化、机械电子工程、机械工程等专业的一门必修课。
创新设计的目标和任务是训练创新思维、学习创新方法、培养创新设计能力。
通过国际化创新思维的比较，帮助学生建立创新设计的思想，培养学生国际化创新意识和能力，打好创造发明的理论和实践的基础。
中国应该学习和改进创新思维，走向世界的前列。
创新是全世界的基本行为，创新教学适合双语教学，打破国际界限，进入英语讨论环境，在通用语言环境下比较优秀创新思想，树立自己的先进创新理念。
本课程通过阐述国际创新设计思想，达到创新理念的树立；创新思维的形成；创新方法的使用；创新活动的指导四大目的，带领学生一边学习，一边创造性实践。
在系统阐述设计创新和创造的基本原理基础上，介绍了设计问题、创新设计策略、设计创新过程、创新产品特性，创新人文特性等内容，用对比的方法，强调创新不只是技术改进，而是技术，市场，社会效益的综合改进，搭建创新与应用的桥梁。
并联系实例构建了“机械创新设计大赛”、“工程训练综合能力大赛”、“机器人大赛”和“创新创业训练计划”等4大实际任务模块，以项目为导向分析和引导相关课程内容的讲授，并结合实验和实训，最终实现学以致用，手脑并用，以大赛的实际创新产品体现教学的效果。
九、课程的基本要求和特点本课程的学习，要求学生具有活跃的思维能力和较强的动手能力，在掌握正确的创新思维和创新方法后，能开动脑筋，按照一定的功能要求，自己动手设计出新型的机构或装置，并加以实验验证。
机械科学与工程研究生课程简介
本课程课堂教学学时32，
1第1章绪论（3）
1.1机械工程科学发展趋势
1.2技术创新
第22创新思维
2.3创造技法
第3章仿生学与创新设计（6）
3.1仿生学与设计创新
3.2仿生机械
3.3仿生机械手
3.4仿步态机构的设计
第4章机械系统运动方案创新设计（8）
先修课程要求：无
课程组教师姓名
职称
专业
年龄
学术专长
杨家军
教授
机械
59
创新设计与机构学
刘世平
副教授
机械
43
现代设计方法与创新设计
朱洲
讲师
机械
36
设计方法学与创新
课程教学目标：
通过介绍机械发展趋势让学生了解科学技术发展前沿，突破思维定势训练创新设计能力，工程实际案例剖析提高产品创新能力，撰写科技论文培养工程综合能力，从整个机械系统着眼，讲解创新设计的方法，训练创新思维方法，着重培养机电产品创新设计能力。
4.1功能原理设计
4.2机构设计
4.3机械系统运动方案的评价
第5章机械创新设计实例及分析（8）
5.1研究性学习
5.2生活中的发明
5.3机器人
5.4农业机械
5．5创新思维与技法训练
教材：
机械创新设计技术杨家军科学出版社2008
主要参考书：机械创新设计张春林机械工业出版社2009
注：每门课程都须填写此表。本表不够可加页
表
课程名称：机械创新设计技术
英文名称：MechanicalDesignInnovation
课程类型：■讲授课程□实践（实验、实习）课程□研讨课程□专题讲座□其它
(机械制造行业)机械专业中英文单词总汇
机械专业英语词汇总汇陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration 气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC 电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheelAssembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism 减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket sprocket-wheel sprocket gear chain wheel联组V 带tight-up V belt联轴器coupling shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design design for environment马耳他机构Geneva wheel Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets。
机电术语中英文对照
端面重合度 transverse contact ratio 端面模数 transverse module 端面压力角 transverse pressure angle 锻造 forge 对称循环应力 symmetry circulating stress 对心滚子从动件 radial (or in-line ) roller follower 对心直动从动件 radial (or in-line ) translating follower 对心移动从动件 radial reciprocating follower 对心曲柄滑块机构 in-line slider-crank (or crank-slider) mechanism 多列轴承 multi-row bearing 多楔带 poly V-belt 多项式运动规律 polynomial motion 多质量转子 rotor with several masses 惰轮 idle gear 额定寿命 rating life 额定载荷 load rating
d 包角 angle of contact
保持架 cage
e 背对背安装 back-to-back arrangement r 背锥 back cone ； normal cone te 背锥角 back angle
背锥距 back cone distance
is 比例尺 scale
比热容 specific heat capacity 闭式链 closed kinematic chain
d 等效量 equivalent
等效质量 equivalent mass
e 等效转动惯量 equivalent moment of inertia r 等效动力学模型 dynamically equivalent model te 底座 chassis
机械类专业英语词汇(设计,理论,模具,量具等)
阿基米德蜗杆 Archimedes worm安全系数 safety factor; factor of safety 安全载荷 safe load凹面、凹度 concavity扳手 wrench板簧 flat leaf spring半圆键 woodruff key变形 deformation摆杆 oscillating bar摆动从动件 oscillating follower摆动从动件凸轮机构 cam with oscillating follower摆动导杆机构 oscillating guide-bar mechanism摆线齿轮 cycloidal gear摆线齿形 cycloidal tooth profile摆线运动规律 cycloidal motion摆线针轮 cycloidal-pin wheel包角 angle of contact保持架 cage背对背安装 back-to-back arrangement 背锥 back cone ；normal cone背锥角 back angle背锥距 back cone distance比例尺 scale比热容 specific heat capacity闭式链 closed kinematic chain闭链机构 closed chain mechanism臂部 arm变频器 frequency converters变频调速 frequency control of motor speed变速 speed change变速齿轮 change gear ; change wheel 变位齿轮 modified gear变位系数 modification coefficient标准齿轮 standard gear标准直齿轮 standard spur gear表面质量系数 superficial mass factor 表面传热系数 surface coefficient of heat transfer表面粗糙度 surface roughness并联式组合 combination in parallel 并联机构 parallel mechanism并联组合机构 parallel combined mechanism并行工程 concurrent engineering并行设计 concurred design, CD不平衡相位 phase angle of unbalance 不平衡 imbalance (or unbalance)不平衡量 amount of unbalance不完全齿轮机构 intermittent gearing 波发生器 wave generator波数 number of waves补偿 compensation参数化设计 parameterization design, PD残余应力 residual stress操纵及控制装置 operation control device槽轮 Geneva wheel槽轮机构 Geneva mechanism ；Maltese cross槽数 Geneva numerate槽凸轮 groove cam侧隙 backlash差动轮系 differential gear train差动螺旋机构 differential screw mechanism差速器 differential常用机构 conventional mechanism; mechanism in common use车床 lathe承载量系数 bearing capacity factor承载能力 bearing capacity成对安装 paired mounting尺寸系列 dimension series齿槽 tooth space齿槽宽 spacewidth齿侧间隙 backlash齿顶高 addendum齿顶圆 addendum circle齿根高 dedendum齿根圆 dedendum circle齿厚 tooth thickness齿距 circular pitch齿宽 face width齿廓 tooth profile齿廓曲线 tooth curve齿轮 gear齿轮变速箱 speed-changing gear boxes齿轮齿条机构 pinion and rack齿轮插刀 pinion cutter; pinion-shaped shaper cutter齿轮滚刀 hob ,hobbing cutter齿轮机构 gear齿轮轮坯 blank齿轮传动系 pinion unit齿轮联轴器 gear coupling齿条传动 rack gear齿数 tooth number齿数比 gear ratio齿条 rack齿条插刀 rack cutter; rack-shaped shaper cutter齿形链、无声链 silent chain齿形系数 form factor齿式棘轮机构 tooth ratchet mechanism插齿机 gear shaper重合点 coincident points重合度 contact ratio冲床 punch传动比 transmission ratio, speed ratio 传动装置 gearing; transmission gear传动系统 driven system传动角 transmission angle传动轴 transmission shaft串联式组合 combination in series串联式组合机构 series combined mechanism串级调速 cascade speed control创新 innovation ; creation创新设计 creation design垂直载荷、法向载荷 normal load唇形橡胶密封 lip rubber seal磁流体轴承 magnetic fluid bearing从动带轮 driven pulley 从动件 driven link, follower从动件平底宽度 width of flat-face从动件停歇 follower dwell从动件运动规律 follower motion从动轮 driven gear粗线 bold line粗牙螺纹 coarse thread大齿轮 gear wheel打包机 packer打滑 slipping带传动 belt driving带轮 belt pulley带式制动器 band brake单列轴承 single row bearing单向推力轴承 single-direction thrust bearing单万向联轴节 single universal joint单位矢量 unit vector当量齿轮 equivalent spur gear; virtual gear当量齿数 equivalent teeth number; virtual number of teeth当量摩擦系数 equivalent coefficient of friction当量载荷 equivalent load刀具 cutter导数 derivative倒角 chamfer导热性 conduction of heat导程 lead导程角 lead angle等加等减速运动规律 parabolic motion; constant acceleration and deceleration motion等速运动规律 uniform motion; constant velocity motion等径凸轮 conjugate yoke radial cam等宽凸轮 constant-breadth cam等效构件 equivalent link等效力 equivalent force等效力矩 equivalent moment of force 等效量 equivalent等效质量 equivalent mass等效转动惯量 equivalent moment of inertia等效动力学模型 dynamically equivalent model底座 chassis低副 lower pair点划线 chain dotted line（疲劳）点蚀 pitting垫圈 gasket垫片密封 gasket seal碟形弹簧 belleville spring顶隙 bottom clearance定轴轮系 ordinary gear train; gear train with fixed axes动力学 dynamics动密封 kinematical seal动能 dynamic energy动力粘度 dynamic viscosity动力润滑 dynamic lubrication动平衡 dynamic balance动平衡机 dynamic balancing machine 动态特性 dynamic characteristics动态分析设计 dynamic analysis design动压力 dynamic reaction动载荷 dynamic load端面 transverse plane端面参数 transverse parameters端面齿距 transverse circular pitch端面齿廓 transverse tooth profile端面重合度 transverse contact ratio端面模数 transverse module端面压力角 transverse pressure angle 锻造 forge对称循环应力 symmetry circulating stress对心滚子从动件 radial (or in-line ) roller follower对心直动从动件 radial (or in-line ) translating follower对心移动从动件 radial reciprocating follower对心曲柄滑块机构 in-line slider-crank (or crank-slider) mechanism多列轴承 multi-row bearing多楔带 poly V-belt多项式运动规律 polynomial motion 多质量转子 rotor with several masses 惰轮 idle gear额定寿命 rating life额定载荷 load ratingII 级杆组 dyad发生线 generating line发生面 generating plane法面 normal plane法面参数 normal parameters法面齿距 normal circular pitch法面模数 normal module法面压力角 normal pressure angle法向齿距 normal pitch法向齿廓 normal tooth profile法向直廓蜗杆 straight sided normal worm法向力 normal force反馈式组合 feedback combining反向运动学 inverse ( or backward) kinematics反转法 kinematic inversion反正切 Arctan范成法 generating cutting仿形法 form cutting方案设计、概念设计 concept design, CD防振装置 shockproof device飞轮 flywheel飞轮矩 moment of flywheel非标准齿轮 nonstandard gear非接触式密封 non-contact seal非周期性速度波动 aperiodic speed fluctuation非圆齿轮 non-circular gear粉末合金 powder metallurgy分度线 reference line; standard pitch line分度圆 reference circle; standard (cutting) pitch circle分度圆柱导程角 lead angle at reference cylinder分度圆柱螺旋角 helix angle at reference cylinder分母 denominator分子 numerator分度圆锥 reference cone; standard pitch cone分析法 analytical method封闭差动轮系 planetary differential复合铰链 compound hinge复合式组合 compound combining复合轮系 compound (or combined) gear train复合平带 compound flat belt复合应力 combined stress复式螺旋机构 Compound screw mechanism复杂机构 complex mechanism杆组 Assur group干涉 interference刚度系数 stiffness coefficient刚轮 rigid circular spline钢丝软轴 wire soft shaft刚体导引机构 body guidance mechanism刚性冲击 rigid impulse (shock)刚性转子 rigid rotor刚性轴承 rigid bearing刚性联轴器 rigid coupling高度系列 height series高速带 high speed belt高副 higher pair格拉晓夫定理 Grashoff`s law根切 undercutting公称直径 nominal diameter高度系列 height series功 work工况系数 application factor工艺设计 technological design工作循环图 working cycle diagram工作机构 operation mechanism工作载荷 external loads 工作空间 working space工作应力 working stress工作阻力 effective resistance工作阻力矩 effective resistance moment公法线 common normal line公共约束 general constraint公制齿轮 metric gears功率 power功能分析设计 function analyses design共轭齿廓 conjugate profiles共轭凸轮 conjugate cam构件 link鼓风机 blower固定构件 fixed link; frame固体润滑剂 solid lubricant关节型操作器 jointed manipulator惯性力 inertia force惯性力矩 moment of inertia ,shaking moment惯性力平衡 balance of shaking force 惯性力完全平衡 full balance of shaking force惯性力部分平衡 partial balance of shaking force惯性主矩 resultant moment of inertia 惯性主失 resultant vector of inertia冠轮 crown gear广义机构 generation mechanism广义坐标 generalized coordinate轨迹生成 path generation轨迹发生器 path generator滚刀 hob滚道 raceway滚动体 rolling element滚动轴承 rolling bearing滚动轴承代号 rolling bearing identification code滚针 needle roller滚针轴承 needle roller bearing滚子 roller滚子轴承 roller bearing滚子半径 radius of roller滚子从动件 roller follower滚子链 roller chain滚子链联轴器 double roller chain coupling滚珠丝杆 ball screw滚柱式单向超越离合器 roller clutch 过度切割 undercutting函数发生器 function generator函数生成 function generation含油轴承 oil bearing耗油量 oil consumption耗油量系数 oil consumption factor赫兹公式 H. Hertz equation合成弯矩 resultant bending moment合力 resultant force合力矩 resultant moment of force黑箱 black box横坐标 abscissa互换性齿轮 interchangeable gears花键 spline滑键、导键 feather key滑动轴承 sliding bearing滑动率 sliding ratio滑块 slider环面蜗杆 toroid helicoids worm环形弹簧 annular spring缓冲装置 shocks; shock-absorber灰铸铁 grey cast iron回程 return回转体平衡 balance of rotors混合轮系 compound gear train积分 integrate机电一体化系统设计 mechanical-electrical integration system design机构 mechanism机构分析 analysis of mechanism机构平衡 balance of mechanism机构学 mechanism机构运动设计 kinematic design of mechanism机构运动简图 kinematic sketch of mechanism机构综合 synthesis of mechanism机构组成 constitution of mechanism 机架 frame, fixed link机架变换 kinematic inversion机器 machine机器人 robot机器人操作器 manipulator机器人学 robotics技术过程 technique process技术经济评价 technical and economic evaluation技术系统 technique system机械 machinery机械创新设计 mechanical creation design, MCD机械系统设计 mechanical system design, MSD机械动力分析 dynamic analysis of machinery机械动力设计 dynamic design of machinery机械动力学 dynamics of machinery机械的现代设计 modern machine design机械系统 mechanical system机械利益 mechanical advantage机械平衡 balance of machinery机械手 manipulator机械设计 machine design; mechanical design机械特性 mechanical behavior机械调速 mechanical speed governors 机械效率 mechanical efficiency机械原理 theory of machines and mechanisms机械运转不均匀系数 coefficient of speed fluctuation机械无级变速 mechanical stepless speed changes基础机构 fundamental mechanism基本额定寿命 basic rating life基于实例设计 case-based design,CBD基圆 base circle基圆半径 radius of base circle基圆齿距 base pitch基圆压力角 pressure angle of base circle基圆柱 base cylinder基圆锥 base cone急回机构 quick-return mechanism急回特性 quick-return characteristics 急回系数 advance-to return-time ratio 急回运动 quick-return motion棘轮 ratchet棘轮机构 ratchet mechanism棘爪 pawl极限位置 extreme (or limiting) position极位夹角 crank angle between extreme (or limiting) positions计算机辅助设计 computer aided design, CAD计算机辅助制造 computer aided manufacturing, CAM计算机集成制造系统 computer integrated manufacturing system, CIMS计算力矩 factored moment; calculation moment计算弯矩 calculated bending moment 加权系数 weighting efficient加速度 acceleration加速度分析 acceleration analysis加速度曲线 acceleration diagram尖点 pointing; cusp尖底从动件 knife-edge follower间隙 backlash间歇运动机构 intermittent motion mechanism减速比 reduction ratio减速齿轮、减速装置 reduction gear 减速器 speed reducer减摩性 anti-friction quality渐开螺旋面 involute helicoid渐开线 involute 渐开线齿廓 involute profile渐开线齿轮 involute gear渐开线发生线 generating line of involute渐开线方程 involute equation渐开线函数 involute function渐开线蜗杆 involute worm渐开线压力角 pressure angle of involute渐开线花键 involute spline简谐运动 simple harmonic motion键 key键槽 keyway交变应力 repeated stress交变载荷 repeated fluctuating load交叉带传动 cross-belt drive交错轴斜齿轮 crossed helical gears胶合 scoring角加速度 angular acceleration角速度 angular velocity角速比 angular velocity ratio角接触球轴承 angular contact ball bearing角接触推力轴承 angular contact thrust bearing角接触向心轴承 angular contact radial bearing角接触轴承 angular contact bearing铰链、枢纽 hinge校正平面 correcting plane接触应力 contact stress接触式密封 contact seal阶梯轴 multi-diameter shaft结构 structure结构设计 structural design截面 section节点 pitch point节距 circular pitch; pitch of teeth节线 pitch line节圆 pitch circle节圆齿厚 thickness on pitch circle节圆直径 pitch diameter节圆锥 pitch cone节圆锥角 pitch cone angle解析设计 analytical design紧边 tight-side紧固件 fastener径节 diametral pitch径向 radial direction径向当量动载荷 dynamic equivalent radial load径向当量静载荷 static equivalent radial load径向基本额定动载荷 basic dynamic radial load rating径向基本额定静载荷 basic static radial load tating径向接触轴承 radial contact bearing 径向平面 radial plane径向游隙 radial internal clearance径向载荷 radial load径向载荷系数 radial load factor径向间隙 clearance静力 static force静平衡 static balance静载荷 static load静密封 static seal局部自由度 passive degree of freedom 矩阵 matrix矩形螺纹 square threaded form锯齿形螺纹 buttress thread form矩形牙嵌式离合器 square-jaw positive-contact clutch绝对尺寸系数 absolute dimensional factor绝对运动 absolute motion绝对速度 absolute velocity均衡装置 load balancing mechanism 抗压强度 compression strength开口传动 open-belt drive开式链 open kinematic chain开链机构 open chain mechanism可靠度 degree of reliability可靠性 reliability可靠性设计 reliability design, RD空气弹簧 air spring 空间机构 spatial mechanism空间连杆机构 spatial linkage空间凸轮机构 spatial cam空间运动副 spatial kinematic pair空间运动链 spatial kinematic chain空转 idle宽度系列 width series框图 block diagram雷诺方程Reynolds‘s equation离心力 centrifugal force离心应力 centrifugal stress离合器 clutch离心密封 centrifugal seal理论廓线 pitch curve理论啮合线 theoretical line of action 隶属度 membership力 force力多边形 force polygon力封闭型凸轮机构 force-drive (or force-closed) cam mechanism力矩 moment力平衡 equilibrium力偶 couple力偶矩 moment of couple连杆 connecting rod, coupler连杆机构 linkage连杆曲线 coupler-curve连心线 line of centers链 chain链传动装置 chain gearing链轮 sprocket ; sprocket-wheel ; sprocket gear ; chain wheel联组V 带 tight-up V belt联轴器 coupling ; shaft coupling两维凸轮 two-dimensional cam临界转速 critical speed六杆机构 six-bar linkage龙门刨床 double Haas planer轮坯 blank轮系 gear train螺杆 screw螺距 thread pitch螺母 screw nut螺旋锥齿轮 helical bevel gear螺钉 screws螺栓 bolts螺纹导程 lead螺纹效率 screw efficiency螺旋传动 power screw螺旋密封 spiral seal螺纹 thread (of a screw)螺旋副 helical pair螺旋机构 screw mechanism螺旋角 helix angle螺旋线 helix ,helical line绿色设计 green design ; design for environment马耳他机构 Geneva wheel ; Geneva gear马耳他十字 Maltese cross脉动无级变速 pulsating stepless speed changes脉动循环应力 fluctuating circulating stress脉动载荷 fluctuating load铆钉 rivet迷宫密封 labyrinth seal密封 seal密封带 seal belt密封胶 seal gum密封元件 potted component密封装置 sealing arrangement面对面安装 face-to-face arrangement 面向产品生命周期设计 design for product`s life cycle, DPLC名义应力、公称应力 nominal stress 模块化设计 modular design, MD模块式传动系统 modular system模幅箱 morphology box模糊集 fuzzy set模糊评价 fuzzy evaluation模数 module摩擦 friction摩擦角 friction angle摩擦力 friction force摩擦学设计 tribology design, TD 摩擦阻力 frictional resistance摩擦力矩 friction moment摩擦系数 coefficient of friction摩擦圆 friction circle磨损 abrasion ;wear; scratching末端执行器 end-effector目标函数 objective function耐腐蚀性 corrosion resistance耐磨性 wear resistance挠性机构 mechanism with flexible elements挠性转子 flexible rotor内齿轮 internal gear内齿圈 ring gear内力 internal force内圈 inner ring能量 energy能量指示图 viscosity逆时针 counterclockwise (or anticlockwise)啮出 engaging-out啮合 engagement, mesh, gearing啮合点 contact points啮合角 working pressure angle啮合线 line of action啮合线长度 length of line of action啮入 engaging-in牛头刨床 shaper凝固点 freezing point; solidifying point扭转应力 torsion stress扭矩 moment of torque扭簧 helical torsion spring诺模图 NomogramO 形密封圈密封 O ring seal盘形凸轮 disk cam盘形转子 disk-like rotor抛物线运动 parabolic motion疲劳极限 fatigue limit疲劳强度 fatigue strength偏置式 offset偏( 心) 距 offset distance偏心率 eccentricity ratio偏心质量 eccentric mass偏距圆 offset circle偏心盘 eccentric偏置滚子从动件 offset roller follower 偏置尖底从动件 offset knife-edge follower偏置曲柄滑块机构 offset slider-crank mechanism拼接 matching评价与决策 evaluation and decision频率 frequency平带 flat belt平带传动 flat belt driving平底从动件 flat-face follower平底宽度 face width平分线 bisector平均应力 average stress平均中径 mean screw diameter平均速度 average velocity平衡 balance平衡机 balancing machine平衡品质 balancing quality平衡平面 correcting plane平衡质量 balancing mass平衡重 counterweight平衡转速 balancing speed平面副 planar pair, flat pair平面机构 planar mechanism平面运动副 planar kinematic pair平面连杆机构 planar linkage平面凸轮 planar cam平面凸轮机构 planar cam mechanism 平面轴斜齿轮 parallel helical gears普通平键 parallel key其他常用机构 other mechanism in common use起动阶段 starting period启动力矩 starting torque气动机构 pneumatic mechanism奇异位置 singular position起始啮合点 initial contact , beginning of contact气体轴承 gas bearing 千斤顶 jack嵌入键 sunk key强迫振动 forced vibration切齿深度 depth of cut曲柄 crank曲柄存在条件 Grashoff`s law曲柄导杆机构 crank shaper (guide-bar) mechanism曲柄滑块机构 slider-crank (or crank-slider) mechanism曲柄摇杆机构 crank-rocker mechanism曲齿锥齿轮 spiral bevel gear曲率 curvature曲率半径 radius of curvature曲面从动件 curved-shoe follower曲线拼接 curve matching曲线运动 curvilinear motion曲轴 crank shaft驱动力 driving force驱动力矩 driving moment (torque)全齿高 whole depth权重集 weight sets球 ball球面滚子 convex roller球轴承 ball bearing球面副 spheric pair球面渐开线 spherical involute球面运动 spherical motion球销副 sphere-pin pair球坐标操作器 polar coordinate manipulator燃点 spontaneous ignition热平衡 heat balance; thermal equilibrium人字齿轮 herringbone gear冗余自由度 redundant degree of freedom柔轮 flexspline柔性冲击 flexible impulse; soft shock 柔性制造系统 flexible manufacturing system; FMS柔性自动化 flexible automation润滑油膜 lubricant film润滑装置 lubrication device润滑 lubrication润滑剂 lubricant三角形花键 serration spline三角形螺纹 V thread screw三维凸轮 three-dimensional cam三心定理 Kennedy`s theorem砂轮越程槽 grinding wheel groove砂漏 hour-glass少齿差行星传动 planetary drive with small teeth difference设计方法学 design methodology设计变量 design variable设计约束 design constraints深沟球轴承 deep groove ball bearing 生产阻力 productive resistance升程 rise升距 lift实际廓线 cam profile十字滑块联轴器 double slider coupling; Oldham‘s coupling矢量 vector输出功 output work输出构件 output link输出机构 output mechanism输出力矩 output torque输出轴 output shaft输入构件 input link数学模型 mathematic model实际啮合线 actual line of action双滑块机构 double-slider mechanism, ellipsograph双曲柄机构 double crank mechanism 双曲面齿轮 hyperboloid gear双头螺柱 studs双万向联轴节 constant-velocity (or double) universal joint双摇杆机构 double rocker mechanism 双转块机构 Oldham coupling双列轴承 double row bearing双向推力轴承 double-direction thrust bearing 松边 slack-side顺时针 clockwise瞬心 instantaneous center死点 dead point四杆机构 four-bar linkage速度 velocity速度不均匀( 波动) 系数 coefficient of speed fluctuation速度波动 speed fluctuation速度曲线 velocity diagram速度瞬心 instantaneous center of velocity塔轮 step pulley踏板 pedal台钳、虎钳 vice太阳轮 sun gear弹性滑动 elasticity sliding motion弹性联轴器 elastic coupling ; flexible coupling弹性套柱销联轴器 rubber-cushioned sleeve bearing coupling套筒 sleeve梯形螺纹 acme thread form特殊运动链 special kinematic chain特性 characteristics替代机构 equivalent mechanism调节 modulation, regulation调心滚子轴承 self-aligning roller bearing调心球轴承 self-aligning ball bearing 调心轴承 self-aligning bearing调速 speed governing调速电动机 adjustable speed motors 调速系统 speed control system调压调速 variable voltage control调速器 regulator, governor铁磁流体密封 ferrofluid seal停车阶段 stopping phase停歇 dwell同步带 synchronous belt同步带传动 synchronous belt drive凸的，凸面体 convex凸轮 cam凸轮倒置机构 inverse cam mechanism 凸轮机构 cam , cam mechanism凸轮廓线 cam profile凸轮廓线绘制 layout of cam profile凸轮理论廓线 pitch curve凸缘联轴器 flange coupling图册、图谱 atlas图解法 graphical method推程 rise推力球轴承 thrust ball bearing推力轴承 thrust bearing退刀槽 tool withdrawal groove退火 anneal陀螺仪 gyroscopeV 带 V belt外力 external force外圈 outer ring外形尺寸 boundary dimension万向联轴器 Hooks coupling ; universal coupling外齿轮 external gear弯曲应力 beading stress弯矩 bending moment腕部 wrist往复移动 reciprocating motion往复式密封 reciprocating seal网上设计 on-net design, OND微动螺旋机构 differential screw mechanism位移 displacement位移曲线 displacement diagram位姿 pose , position and orientation稳定运转阶段 steady motion period稳健设计 robust design蜗杆 worm蜗杆传动机构 worm gearing蜗杆头数 number of threads蜗杆直径系数 diametral quotient蜗杆蜗轮机构 worm and worm gear 蜗杆形凸轮步进机构 worm cam interval mechanism蜗杆旋向 hands of worm蜗轮 worm gear 涡圈形盘簧 power spring无级变速装置 stepless speed changes devices无穷大 infinite系杆 crank arm, planet carrier现场平衡 field balancing向心轴承 radial bearing向心力 centrifugal force相对速度 relative velocity相对运动 relative motion相对间隙 relative gap象限 quadrant橡皮泥 plasticine细牙螺纹 fine threads销 pin消耗 consumption小齿轮 pinion小径 minor diameter橡胶弹簧 balata spring修正梯形加速度运动规律 modified trapezoidal acceleration motion修正正弦加速度运动规律 modified sine acceleration motion斜齿圆柱齿轮 helical gear斜键、钩头楔键 taper key泄漏 leakage谐波齿轮 harmonic gear谐波传动 harmonic driving谐波发生器 harmonic generator斜齿轮的当量直齿轮 equivalent spur gear of the helical gear心轴 spindle行程速度变化系数 coefficient of travel speed variation行程速比系数 advance-to return-time ratio行星齿轮装置 planetary transmission 行星轮 planet gear行星轮变速装置 planetary speed changing devices行星轮系 planetary gear train形封闭凸轮机构 positive-drive (or form-closed) cam mechanism虚拟现实 virtual reality虚拟现实技术 virtual reality technology, VRT虚拟现实设计 virtual reality design, VRD虚约束 redundant (or passive) constraint许用不平衡量 allowable amount of unbalance许用压力角 allowable pressure angle 许用应力 allowable stress; permissible stress悬臂结构 cantilever structure悬臂梁 cantilever beam循环功率流 circulating power load旋转力矩 running torque旋转式密封 rotating seal旋转运动 rotary motion选型 type selection压力 pressure压力中心 center of pressure压缩机 compressor压应力 compressive stress压力角 pressure angle牙嵌式联轴器 jaw (teeth) positive-contact coupling雅可比矩阵 Jacobi matrix摇杆 rocker液力传动 hydrodynamic drive液力耦合器 hydraulic couplers液体弹簧 liquid spring液压无级变速 hydraulic stepless speed changes液压机构 hydraulic mechanism一般化运动链 generalized kinematic chain移动从动件 reciprocating follower移动副 prismatic pair, sliding pair移动关节 prismatic joint移动凸轮 wedge cam盈亏功 increment or decrement work 应力幅 stress amplitude应力集中 stress concentration 应力集中系数 factor of stress concentration应力图 stress diagram应力—应变图 stress-strain diagram 优化设计 optimal design油杯 oil bottle油壶 oil can油沟密封 oily ditch seal有害阻力 useless resistance有益阻力 useful resistance有效拉力 effective tension有效圆周力 effective circle force有害阻力 detrimental resistance余弦加速度运动 cosine acceleration (or simple harmonic) motion预紧力 preload原动机 primer mover圆带 round belt圆带传动 round belt drive圆弧齿厚 circular thickness圆弧圆柱蜗杆 hollow flank worm圆角半径 fillet radius圆盘摩擦离合器 disc friction clutch圆盘制动器 disc brake原动机 prime mover原始机构 original mechanism圆形齿轮 circular gear圆柱滚子 cylindrical roller圆柱滚子轴承 cylindrical roller bearing圆柱副 cylindric pair圆柱式凸轮步进运动机构 barrel (cylindric) cam圆柱螺旋拉伸弹簧 cylindroid helical-coil extension spring圆柱螺旋扭转弹簧 cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧 cylindroid helical-coil compression spring圆柱凸轮 cylindrical cam圆柱蜗杆 cylindrical worm圆柱坐标操作器 cylindrical coordinate manipulator圆锥螺旋扭转弹簧 conoid helical-coil compression spring圆锥滚子 tapered roller圆锥滚子轴承 tapered roller bearing 圆锥齿轮机构 bevel gears圆锥角 cone angle原动件 driving link约束 constraint约束条件 constraint condition约束反力 constraining force跃度 jerk跃度曲线 jerk diagram运动倒置 kinematic inversion运动方案设计 kinematic precept design运动分析 kinematic analysis运动副 kinematic pair运动构件 moving link运动简图 kinematic sketch运动链 kinematic chain运动失真 undercutting运动设计 kinematic design运动周期 cycle of motion运动综合 kinematic synthesis运转不均匀系数 coefficient of velocity fluctuation运动粘度 kenematic viscosity载荷 load载荷—变形曲线 load—deformation curve载荷—变形图 load—deformation diagram窄V 带 narrow V belt毡圈密封 felt ring seal展成法 generating张紧力 tension张紧轮 tension pulley振动 vibration振动力矩 shaking couple振动频率 frequency of vibration振幅 amplitude of vibration正切机构 tangent mechanism正向运动学 direct (forward) kinematics正弦机构 sine generator, scotch yoke 织布机 loom正应力、法向应力 normal stress制动器 brake直齿圆柱齿轮 spur gear直齿锥齿轮 straight bevel gear直角三角形 right triangle直角坐标操作器 Cartesian coordinate manipulator直径系数 diametral quotient直径系列 diameter series直廓环面蜗杆 hindley worm直线运动 linear motion直轴 straight shaft质量 mass质心 center of mass执行构件 executive link; working link 质径积 mass-radius product智能化设计 intelligent design, ID中间平面 mid-plane中心距 center distance中心距变动 center distance change中心轮 central gear中径 mean diameter终止啮合点 final contact, end of contact周节 pitch周期性速度波动 periodic speed fluctuation周转轮系 epicyclic gear train肘形机构 toggle mechanism轴 shaft轴承盖 bearing cup轴承合金 bearing alloy轴承座 bearing block轴承高度 bearing height轴承宽度 bearing width轴承内径 bearing bore diameter轴承寿命 bearing life轴承套圈 bearing ring轴承外径 bearing outside diameter轴颈 journal轴瓦、轴承衬 bearing bush轴端挡圈 shaft end ring轴环 shaft collar轴肩 shaft shoulder轴角 shaft angle轴向 axial direction轴向齿廓 axial tooth profile轴向当量动载荷 dynamic equivalent axial load轴向当量静载荷 static equivalent axial load轴向基本额定动载荷 basic dynamic axial load rating轴向基本额定静载荷 basic static axial load rating轴向接触轴承 axial contact bearing轴向平面 axial plane轴向游隙 axial internal clearance轴向载荷 axial load轴向载荷系数 axial load factor轴向分力 axial thrust load主动件 driving link主动齿轮 driving gear主动带轮 driving pulley转动导杆机构 whitworth mechanism 转动副 revolute (turning) pair转速 swiveling speed ; rotating speed 转动关节 revolute joint转轴 revolving shaft转子 rotor转子平衡 balance of rotor装配条件 assembly condition锥齿轮 bevel gear锥顶 common apex of cone锥距 cone distance锥轮 bevel pulley; bevel wheel锥齿轮的当量直齿轮 equivalent spur gear of the bevel gear锥面包络圆柱蜗杆 milled helicoids worm准双曲面齿轮 hypoid gear子程序 subroutine子机构 sub-mechanism 自动化 automation自锁 self-locking自锁条件 condition of self-locking自由度 degree of freedom, mobility总重合度 total contact ratio总反力 resultant force总效率 combined efficiency; overall efficiency组成原理 theory of constitution组合齿形 composite tooth form组合安装 stack mounting组合机构 combined mechanism阻抗力 resistance最大盈亏功 maximum difference work between plus and minus work纵向重合度 overlap contact ratio纵坐标 ordinate组合机构 combined mechanism最少齿数 minimum teeth number最小向径 minimum radius作用力 applied force坐标系 coordinate frame。
机械设计名词术语中英文对照表(1)
机械设计名词术语中英文对照表(1)传动比 transmission ratio, speed ratio 传动装置 gearing; transmission gear传动系统 driven system 传动角 transmission angle传动轴 transmission shaft 串联式组合 combination in series串联式组合机构 series combined mechanism 串级调速 cascade speed control创新 innovation ; creation 创新设计 creation design垂直载荷、法向载荷 normal load 唇形橡胶密封 lip rubber seal磁流体轴承 magnetic fluid bearing 从动带轮 driven pulley从动件 driven link, follower 从动件平底宽度 width of flat-face从动件停歇 follower dwell 从动件运动规律 follower motion从动轮 driven gear 粗线 bold line粗牙螺纹 coarse thread 大齿轮 gear wheel打包机 packer 打滑 slipping带传动 belt driving 带轮 belt pulley带式制动器 band brake 单列轴承 single row bearing单向推力轴承 single-direction thrust bearing 单万向联轴节 single universal joint单位矢量 unit vector 当量齿轮 equivalent spur gear; virtual gear当量齿数 equivalent teeth number; virtual number of teeth 当量摩擦系数 equivalent coefficient of friction当量载荷 equivalent load 刀具 cutter导数 derivative 倒角 chamfer导热性 conduction of heat 导程 lead导程角 lead angle 等加等减速运动规律 parabolic motion; constant acceleration and deceleration motion 等速运动规律 uniform motion; constant velocity motion 等径凸轮 conjugate yoke radial cam等宽凸轮 constant-breadth cam 等效构件 equivalent link等效力 equivalent force 等效力矩 equivalent moment of force等效量 equivalent 等效质量 equivalent mass等效转动惯量 equivalent moment of inertia 等效动力学模型 dynamically equivalent model底座 chassis 低副 lower pair点划线 chain dotted line 〔疲劳〕点蚀 pitting垫圈 gasket 垫片密封 gasket seal碟形弹簧 belleville spring 顶隙 bottom clearance定轴轮系 ordinary gear train; gear train with fixed axes 动力学 dynamics动密封 kinematical seal 动能 dynamic energy动力粘度 dynamic viscosity 动力润滑 dynamic lubrication动平稳 dynamic balance 动平稳机 dynamic balancing machine动态特性 dynamic characteristics 动态分析设计 dynamic analysis design动压力 dynamic reaction 动载荷 dynamic load端面 transverse plane 端面参数 transverse parameters端面齿距 transverse circular pitch 端面齿廓 transverse tooth profile端面重合度 transverse contact ratio 端面模数 transverse module端面压力角 transverse pressure angle 锻造 forge对称循环应力 symmetry circulating stress 对心滚子从动件 radial (or in-line ) roller follower对心直动从动件 radial (or in-line ) translating follower 对心移动从动件 radial reciprocating follower对心曲柄滑块机构 in-line slider-crank (or crank-slider) mechanism 多列轴承 multi-row bearing多楔带 poly V-belt 多项式运动规律 polynomial motion多质量转子 rotor with several masses 惰轮 idle gear额定寿命 rating life 额定载荷 load ratingII 级杆组 dyad 发生线 generating line发生面 generating plane 法面 normal plane法面参数 normal parameters 法面齿距 normal circular pitch法面模数 normal module 法面压力角 normal pressure angle 〔2 页〕法向齿距 normal pitch 法向齿廓 normal tooth profile法向直廓蜗杆 straight sided normal worm 法向力 normal force反馈式组合 feedback combining 反向运动学 inverse ( or backward) kinematics反转法 kinematic inversion反正切 Arctan范成法 generating cutting仿形法 form cutting方案设计、概念设计 concept design, CD防振装置 shockproof device飞轮 flywheel飞轮矩 moment of flywheel非标准齿轮 nonstandard gear非接触式密封 non-contact seal非周期性速度波动 aperiodic speed fluctuation非圆齿轮 non-circular gear粉末合金 powder metallurgy分度线 reference line; standard pitch line分度圆 reference circle; standard (cutting) pitch circle分度圆柱导程角 lead angle at reference cylinder分度圆柱螺旋角 helix angle at reference cylinder分母 denominator分子 numerator分度圆锥 reference cone; standard pitch cone分析法 analytical method封闭差动轮系 planetary differential复合铰链 compound hinge复合式组合 compound combining复合轮系 compound (or combined) gear train复合平带 compound flat belt复合应力 combined stress复式螺旋机构 Compound screw mechanism复杂机构 complex mechanism杆组 Assur group干涉 interference 刚度系数 stiffness coefficient刚轮 rigid circular spline钢丝软轴 wire soft shaft刚体导引机构 body guidance mechanism刚性冲击 rigid impulse (shock)刚性转子 rigid rotor刚性轴承 rigid bearing刚性联轴器 rigid coupling高度系列 height series高速带 high speed belt高副 higher pair格拉晓夫定理 Grashoff`s law根切 undercutting公称直径 nominal diameter高度系列 height series功 work工况系数 application factor工艺设计 technological design工作循环图 working cycle diagram工作机构 operation mechanism工作载荷 external loads工作空间 working space工作应力 working stress工作阻力 effective resistance工作阻力矩 effective resistance moment公法线 common normal line公共约束 general constraint公制齿轮 metric gears功率 power功能分析设计 function analyses design共轭齿廓 conjugate profiles共轭凸轮 conjugate cam构件 link鼓风机 blower固定构件 fixed link; frame固体润滑剂 solid lubricant关节型操作器 jointed manipulator惯性力 inertia force惯性力矩 moment of inertia ,shaking moment惯性力平稳 balance of shaking force惯性力完全平稳 full balance of shaking force惯性力部分平稳 partial balance of shaking force惯性主矩 resultant moment of inertia惯性主失 resultant vector of inertia冠轮 crown gear广义机构 generation mechanism广义坐标 generalized coordinate轨迹生成 path generation轨迹发生器 path generator滚刀 hob滚道 raceway滚动体 rolling element滚动轴承 rolling bearing滚动轴承代号 rolling bearing identification code滚针 needle roller滚针轴承 needle roller bearing滚子 roller滚子轴承 roller bearing滚子半径 radius of roller滚子从动件 roller follower滚子链 roller chain滚子链联轴器 double roller chain coupling滚珠丝杆 ball screw滚柱式单向超越离合器 roller clutch过度切割 undercutting函数发生器 function generator函数生成 function generation含油轴承 oil bearing耗油量 oil consumption耗油量系数 oil consumption factor赫兹公式 H. Hertz equation合成弯矩 resultant bending moment合力 resultant force合力矩 resultant moment of force黑箱 black box横坐标 abscissa互换性齿轮 interchangeable gears花键 spline滑键、导键 feather key滑动轴承 sliding bearing滑动率 sliding ratio滑块 slider环面蜗杆 toroid helicoids worm环形弹簧 annular spring缓冲装置 shocks; shock-absorber灰铸铁 grey cast iron回程 return回转体平稳 balance of rotors混合轮系 compound gear train积分 integrate机电一体化系统设计 mechanical-electrical integration system design 机构 mechanism机构分析 analysis of mechanism机构平稳 balance of mechanism机构学 mechanism机构运动设计 kinematic design of mechanism机构运动简图 kinematic sketch of mechanism机构综合 synthesis of mechanism机构组成 constitution of mechanism机架 frame, fixed link机架变换 kinematic inversion机器 machine机器人 robot机器人操作器 manipulator机器人学 robotics技术过程 technique process技术经济评判 technical and economic evaluation技术系统 technique system机械 machinery机械创新设计 mechanical creation design, MCD机械系统设计 mechanical system design, MSD机械动力分析 dynamic analysis of machinery机械动力设计 dynamic design of machinery机械动力学 dynamics of machinery机械的现代设计 modern machine design机械系统 mechanical system机械利益 mechanical advantage机械平稳 balance of machinery机械手 manipulator机械设计 machine design; mechanical design机械特性 mechanical behavior机械调速 mechanical speed governors机械效率 mechanical efficiency机械原理 theory of machines and mechanisms机械运转不平均系数 coefficient of speed fluctuation机械无级变速 mechanical stepless speed changes基础机构 fundamental mechanism差不多额定寿命 basic rating life基于实例设计 case-based design,CBD基圆 base circle基圆半径 radius of base circle基圆齿距 base pitch基圆压力角 pressure angle of base circle基圆柱 base cylinder基圆锥 base cone急回机构 quick-return mechanism急回特性 quick-return characteristics急回系数 advance-to return-time ratio急回运动 quick-return motion棘轮 ratchet棘轮机构 ratchet mechanism棘爪 pawl极限位置 extreme (or limiting) position极位夹角 crank angle between extreme (or limiting) positions运算机辅助设计 computer aided design, CAD运算机辅助制造 computer aided manufacturing, CAM运算机集成制造系统 computer integrated manufacturing system, CIMS 运算力矩 factored moment; calculation moment运算弯矩 calculated bending moment加权系数 weighting efficient加速度 acceleration加速度分析 acceleration analysis加速度曲线 acceleration diagram尖点 pointing; cusp尖底从动件 knife-edge follower间隙 backlash间歇运动机构 intermittent motion mechanism减速比 reduction ratio减速齿轮、减速装置 reduction gear减速器 speed reducer减摩性 anti-friction quality渐开螺旋面 involute helicoid渐开线 involute渐开线齿廓 involute profile渐开线齿轮 involute gear渐开线发生线 generating line of involute渐开线方程 involute equation渐开线函数 involute function渐开线蜗杆 involute worm渐开线压力角 pressure angle of involute渐开线花键 involute spline简谐运动 simple harmonic motion键 key键槽 keyway交变应力 repeated stress交变载荷 repeated fluctuating load交叉带传动 cross-belt drive交错轴斜齿轮 crossed helical gears胶合 scoring角加速度 angular acceleration角速度 angular velocity角速比 angular velocity ratio角接触球轴承 angular contact ball bearing角接触推力轴承 angular contact thrust bearing角接触向心轴承 angular contact radial bearing角接触轴承 angular contact bearing铰链、枢纽 hinge校正平面 correcting plane接触应力 contact stress接触式密封 contact seal阶梯轴 multi-diameter shaft结构 structure结构设计 structural design截面 section节点 pitch point节距 circular pitch; pitch of teeth节线 pitch line节圆 pitch circle节圆齿厚 thickness on pitch circle节圆直径 pitch diameter节圆锥 pitch cone节圆锥角 pitch cone angle解析设计 analytical design紧边 tight-side紧固件 fastener径节 diametral pitch径向 radial direction径向当量动载荷 dynamic equivalent radial load径向当量静载荷 static equivalent radial load径向差不多额定动载荷 basic dynamic radial load rating 径向差不多额定静载荷 basic static radial load tating径向接触轴承 radial contact bearing径向平面 radial plane径向游隙 radial internal clearance径向载荷 radial load径向载荷系数 radial load factor径向间隙 clearance静力 static force静平稳 static balance静载荷 static load静密封 static seal局部自由度 passive degree of freedom矩阵 matrix矩形螺纹 square threaded form锯齿形螺纹 buttress thread form矩形牙嵌式离合器 square-jaw positive-contact clutch绝对尺寸系数 absolute dimensional factor绝对运动 absolute motion绝对速度 absolute velocity均衡装置 load balancing mechanism抗压强度 compression strength开口传动 open-belt drive开式链 open kinematic chain开链机构 open chain mechanism可靠度 degree of reliability可靠性 reliability可靠性设计 reliability design, RD空气弹簧 air spring空间机构 spatial mechanism空间连杆机构 spatial linkage空间凸轮机构 spatial cam空间运动副 spatial kinematic pair空间运动链 spatial kinematic chain空转 idle宽度系列 width series框图 block diagram雷诺方程 Reynolds‘s equation离心力 centrifugal force离心应力 centrifugal stress离合器 clutch离心密封 centrifugal seal理论廓线 pitch curve理论啮合线 theoretical line of action隶属度 membership力 force力多边形 force polygon力封闭型凸轮机构 force-drive (or force-closed) cam mechanism 力矩 moment力平稳 equilibrium力偶 couple力偶矩 moment of couple连杆 connecting rod, coupler连杆机构 linkage连杆曲线 coupler-curve连心线 line of centers链 chain链传动装置 chain gearing链轮 sprocket ; sprocket-wheel ; sprocket gear ; chain wheel 联组V 带 tight-up V belt联轴器 coupling ; shaft coupling两维凸轮 two-dimensional cam临界转速 critical speed六杆机构 six-bar linkage龙门刨床 double Haas planer轮坯 blank轮系 gear train螺杆 screw螺距 thread pitch螺母 screw nut螺旋锥齿轮 helical bevel gear螺钉 screws螺栓 bolts螺纹导程 lead螺纹效率 screw efficiency螺旋传动 power screw螺旋密封 spiral seal螺纹 thread (of a screw)螺旋副 helical pair螺旋机构 screw mechanism螺旋角 helix angle螺旋线 helix ,helical line绿色设计 green design ; design for environment马耳他机构 Geneva wheel ; Geneva gear马耳他十字 Maltese cross脉动无级变速 pulsating stepless speed changes脉动循环应力 fluctuating circulating stress脉动载荷 fluctuating load铆钉 rivet迷宫密封 labyrinth seal密封 seal密封带 seal belt密封胶 seal gum密封元件 potted component密封装置 sealing arrangement面对面安装 face-to-face arrangement面向产品生命周期设计 design for product`s life cycle, DPLC 名义应力、公称应力 nominal stress模块化设计 modular design, MD模块式传动系统 modular system模幅箱 morphology box模糊集 fuzzy set模糊评判 fuzzy evaluation模数 module摩擦 friction摩擦角 friction angle摩擦力 friction force摩擦学设计 tribology design, TD摩擦阻力 frictional resistance摩擦力矩 friction moment摩擦系数 coefficient of friction摩擦圆 friction circle磨损 abrasion ;wear; scratching末端执行器 end-effector目标函数 objective function耐腐蚀性 corrosion resistance耐磨性 wear resistance挠性机构 mechanism with flexible elements挠性转子 flexible rotor内齿轮 internal gear内齿圈 ring gear内力 internal force内圈 inner ring能量 energy能量指示图 viscosity逆时针 counterclockwise (or anticlockwise)啮出 engaging-out啮合 engagement, mesh, gearing啮合点 contact points啮合角 working pressure angle啮合线 line of action啮合线长度 length of line of action啮入 engaging-in牛头刨床 shaper凝固点 freezing point; solidifying point扭转应力 torsion stress扭矩 moment of torque扭簧 helical torsion spring诺模图 NomogramO 形密封圈密封 O ring seal盘形凸轮 disk cam盘形转子 disk-like rotor抛物线运动 parabolic motion疲劳极限 fatigue limit疲劳强度 fatigue strength偏置式 offset偏( 心) 距 offset distance偏心率 eccentricity ratio偏心质量 eccentric mass偏距圆 offset circle偏心盘 eccentric偏置滚子从动件 offset roller follower偏置尖底从动件 offset knife-edge follower偏置曲柄滑块机构 offset slider-crank mechanism 拼接 matching评判与决策 evaluation and decision频率 frequency平带 flat belt平带传动 flat belt driving平底从动件 flat-face follower平底宽度 face width平分线 bisector平均应力 average stress平均中径 mean screw diameter平均速度 average velocity平稳 balance平稳机 balancing machine平稳品质 balancing quality平稳平面 correcting plane平稳质量 balancing mass平稳重 counterweight平稳转速 balancing speed平面副 planar pair, flat pair平面机构 planar mechanism平面运动副 planar kinematic pair平面连杆机构 planar linkage平面凸轮 planar cam平面凸轮机构 planar cam mechanism平面轴斜齿轮 parallel helical gears一般平键 parallel key其他常用机构 other mechanism in common use起动时期 starting period启动力矩 starting torque气动机构 pneumatic mechanism奇特位置 singular position起始啮合点 initial contact , beginning of contact气体轴承 gas bearing千斤顶 jack嵌入键 sunk key强迫振动 forced vibration切齿深度 depth of cut曲柄 crank曲柄存在条件 Grashoff`s law曲柄导杆机构 crank shaper (guide-bar) mechanism曲柄滑块机构 slider-crank (or crank-slider) mechanism 曲柄摇杆机构 crank-rocker mechanism曲齿锥齿轮 spiral bevel gear曲率 curvature曲率半径 radius of curvature曲面从动件 curved-shoe follower曲线拼接 curve matching曲线运动 curvilinear motion曲轴 crank shaft驱动力 driving force驱动力矩 driving moment (torque)全齿高 whole depth权重集 weight sets球 ball球面滚子 convex roller球轴承 ball bearing球面副 spheric pair球面渐开线 spherical involute球面运动 spherical motion球销副 sphere-pin pair球坐标操作器 polar coordinate manipulator燃点 spontaneous ignition热平稳 heat balance; thermal equilibrium人字齿轮 herringbone gear冗余自由度 redundant degree of freedom柔轮 flexspline柔性冲击 flexible impulse; soft shock柔性制造系统 flexible manufacturing system; FMS柔性自动化 flexible automation润滑油膜 lubricant film润滑装置 lubrication device润滑 lubrication润滑剂 lubricant三角形花键 serration spline三角形螺纹 V thread screw三维凸轮 three-dimensional cam三心定理 Kennedy`s theorem砂轮越程槽 grinding wheel groove砂漏 hour-glass少齿差行星传动 planetary drive with small teeth difference 设计方法学 design methodology设计变量 design variable设计约束 design constraints深沟球轴承 deep groove ball bearing生产阻力 productive resistance升程 rise升距 lift实际廓线 cam profile十字滑块联轴器 double slider coupling; Oldham‘s coupling 矢量 vector输出功 output work输出构件 output link输出机构 output mechanism输出力矩 output torque输出轴 output shaft输入构件 input link数学模型 mathematic model实际啮合线 actual line of action双滑块机构 double-slider mechanism, ellipsograph双曲柄机构 double crank mechanism双曲面齿轮 hyperboloid gear双头螺柱 studs双万向联轴节 constant-velocity (or double) universal joint双摇杆机构 double rocker mechanism双转块机构 Oldham coupling双列轴承 double row bearing双向推力轴承 double-direction thrust bearing松边 slack-side顺时针 clockwise瞬心 instantaneous center死点 dead point四杆机构 four-bar linkage速度 velocity速度不平均( 波动) 系数 coefficient of speed fluctuation 速度波动 speed fluctuation速度曲线 velocity diagram速度瞬心 instantaneous center of velocity塔轮 step pulley踏板 pedal台钳、虎钳 vice太阳轮 sun gear弹性滑动 elasticity sliding motion弹性联轴器 elastic coupling ; flexible coupling弹性套柱销联轴器 rubber-cushioned sleeve bearing coupling 套筒 sleeve梯形螺纹 acme thread form专门运动链 special kinematic chain特性 characteristics替代机构 equivalent mechanism调剂 modulation, regulation调心滚子轴承 self-aligning roller bearing调心球轴承 self-aligning ball bearing调心轴承 self-aligning bearing调速 speed governing调速电动机 adjustable speed motors调速系统 speed control system调压调速 variable voltage control调速器 regulator, governor铁磁流体密封 ferrofluid seal停车时期 stopping phase停歇 dwell同步带 synchronous belt同步带传动 synchronous belt drive凸的，凸面体 convex凸轮 cam凸轮倒置机构 inverse cam mechanism凸轮机构 cam , cam mechanism凸轮廓线 cam profile凸轮廓线绘制 layout of cam profile凸轮理论廓线 pitch curve凸缘联轴器 flange coupling图册、图谱 atlas图解法 graphical method推程 rise推力球轴承 thrust ball bearing推力轴承 thrust bearing退刀槽 tool withdrawal groove退火 anneal陀螺仪 gyroscopeV 带 V belt外力 external force外圈 outer ring外形尺寸 boundary dimension万向联轴器 Hooks coupling ; universal coupling外齿轮 external gear弯曲应力 beading stress弯矩 bending moment腕部 wrist往复移动 reciprocating motion往复式密封 reciprocating seal网上设计 on-net design, OND微动螺旋机构 differential screw mechanism位移 displacement位移曲线 displacement diagram位姿 pose , position and orientation稳固运转时期 steady motion period稳健设计 robust design蜗杆 worm蜗杆传动机构 worm gearing蜗杆头数 number of threads蜗杆直径系数 diametral quotient蜗杆蜗轮机构 worm and worm gear蜗杆形凸轮步进机构 worm cam interval mechanism蜗杆旋向 hands of worm蜗轮 worm gear涡圈形盘簧 power spring无级变速装置 stepless speed changes devices无穷大 infinite系杆 crank arm, planet carrier现场平稳 field balancing向心轴承 radial bearing向心力 centrifugal force相对速度 relative velocity相对运动 relative motion相对间隙 relative gap象限 quadrant橡皮泥 plasticine细牙螺纹 fine threads销 pin消耗 consumption小齿轮 pinion小径 minor diameter橡胶弹簧 balata spring修正梯形加速度运动规律 modified trapezoidal acceleration motion 修正正弦加速度运动规律 modified sine acceleration motion斜齿圆柱齿轮 helical gear斜键、钩头楔键 taper key泄漏 leakage谐波齿轮 harmonic gear谐波传动 harmonic driving谐波发生器 harmonic generator斜齿轮的当量直齿轮 equivalent spur gear of the helical gear心轴 spindle行程速度变化系数 coefficient of travel speed variation行程速比系数 advance-to return-time ratio行星齿轮装置 planetary transmission行星轮 planet gear行星轮变速装置 planetary speed changing devices行星轮系 planetary gear train形封闭凸轮机构 positive-drive (or form-closed) cam mechanism 虚拟现实 virtual reality虚拟现实技术 virtual reality technology, VRT虚拟现实设计 virtual reality design, VRD虚约束 redundant (or passive) constraint许用不平稳量 allowable amount of unbalance许用压力角 allowable pressure angle许用应力 allowable stress; permissible stress悬臂结构 cantilever structure悬臂梁 cantilever beam循环功率流 circulating power load旋转力矩 running torque旋转式密封 rotating seal旋转运动 rotary motion选型 type selection压力 pressure压力中心 center of pressure压缩机 compressor压应力 compressive stress压力角 pressure angle牙嵌式联轴器 jaw (teeth) positive-contact coupling雅可比矩阵 Jacobi matrix摇杆 rocker液力传动 hydrodynamic drive液力耦合器 hydraulic couplers液体弹簧 liquid spring液压无级变速 hydraulic stepless speed changes液压机构 hydraulic mechanism一样化运动链 generalized kinematic chain移动从动件 reciprocating follower移动副 prismatic pair, sliding pair移动关节 prismatic joint移动凸轮 wedge cam盈亏功 increment or decrement work应力幅 stress amplitude应力集中 stress concentration应力集中系数 factor of stress concentration应力图 stress diagram应力—应变图 stress-strain diagram优化设计 optimal design油杯 oil bottle油壶 oil can油沟密封 oily ditch seal有害阻力 useless resistance有益阻力 useful resistance有效拉力 effective tension有效圆周力 effective circle force有害阻力 detrimental resistance余弦加速度运动 cosine acceleration (or simple harmonic) motion 预紧力 preload原动机 primer mover圆带 round belt圆带传动 round belt drive圆弧齿厚 circular thickness圆弧圆柱蜗杆 hollow flank worm圆角半径 fillet radius圆盘摩擦离合器 disc friction clutch圆盘制动器 disc brake原动机 prime mover原始机构 original mechanism圆形齿轮 circular gear圆柱滚子 cylindrical roller圆柱滚子轴承 cylindrical roller bearing圆柱副 cylindric pair圆柱式凸轮步进运动机构 barrel (cylindric) cam圆柱螺旋拉伸弹簧 cylindroid helical-coil extension spring圆柱螺旋扭转弹簧 cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧 cylindroid helical-coil compression spring圆柱凸轮 cylindrical cam圆柱蜗杆 cylindrical worm圆柱坐标操作器 cylindrical coordinate manipulator圆锥螺旋扭转弹簧 conoid helical-coil compression spring圆锥滚子 tapered roller圆锥滚子轴承 tapered roller bearing圆锥齿轮机构 bevel gears圆锥角 cone angle原动件 driving link约束 constraint约束条件 constraint condition约束反力 constraining force跃度 jerk跃度曲线 jerk diagram运动倒置 kinematic inversion运动方案设计 kinematic precept design运动分析 kinematic analysis运动副 kinematic pair运动构件 moving link运动简图 kinematic sketch运动链 kinematic chain运动失真 undercutting运动设计 kinematic design运动周期 cycle of motion运动综合 kinematic synthesis运转不平均系数 coefficient of velocity fluctuation 运动粘度 kenematic viscosity载荷 load载荷—变形曲线 load—deformation curve载荷—变形图 load—deformation diagram窄V 带 narrow V belt毡圈密封 felt ring seal展成法 generating张紧力 tension张紧轮 tension pulley振动 vibration振动力矩 shaking couple振动频率 frequency of vibration振幅 amplitude of vibration正切机构 tangent mechanism正向运动学 direct (forward) kinematics正弦机构 sine generator, scotch yoke织布机 loom正应力、法向应力 normal stress制动器 brake直齿圆柱齿轮 spur gear直齿锥齿轮 straight bevel gear直角三角形 right triangle直角坐标操作器 Cartesian coordinate manipulator 直径系数 diametral quotient直径系列 diameter series直廓环面蜗杆 hindley worm直线运动 linear motion直轴 straight shaft质量 mass质心 center of mass执行构件 executive link; working link质径积 mass-radius product智能化设计 intelligent design, ID中间平面 mid-plane中心距 center distance中心距变动 center distance change中心轮 central gear中径 mean diameter终止啮合点 final contact, end of contact周节 pitch周期性速度波动 periodic speed fluctuation周转轮系 epicyclic gear train肘形机构 toggle mechanism轴 shaft轴承盖 bearing cup轴承合金 bearing alloy轴承座 bearing block轴承高度 bearing height轴承宽度 bearing width轴承内径 bearing bore diameter轴承寿命 bearing life轴承套圈 bearing ring轴承外径 bearing outside diameter轴颈 journal轴瓦、轴承衬 bearing bush轴端挡圈 shaft end ring轴环 shaft collar轴肩 shaft shoulder轴角 shaft angle轴向 axial direction轴向齿廓 axial tooth profile轴向当量动载荷 dynamic equivalent axial load轴向当量静载荷 static equivalent axial load轴向差不多额定动载荷 basic dynamic axial load rating轴向差不多额定静载荷 basic static axial load rating轴向接触轴承 axial contact bearing轴向平面 axial plane轴向游隙 axial internal clearance轴向载荷 axial load轴向载荷系数 axial load factor轴向分力 axial thrust load主动件 driving link主动齿轮 driving gear主动带轮 driving pulley转动导杆机构 whitworth mechanism转动副 revolute (turning) pair转速 swiveling speed ; rotating speed转动关节 revolute joint转轴 revolving shaft转子 rotor转子平稳 balance of rotor装配条件 assembly condition锥齿轮 bevel gear锥顶 common apex of cone锥距 cone distance锥轮 bevel pulley; bevel wheel锥齿轮的当量直齿轮 equivalent spur gear of the bevel gear 锥面包络圆柱蜗杆 milled helicoids worm准双曲面齿轮 hypoid gear子程序 subroutine子机构 sub-mechanism自动化 automation自锁 self-locking自锁条件 condition of self-locking自由度 degree of freedom, mobility总重合度 total contact ratio总反力 resultant force总效率 combined efficiency; overall efficiency组成原理 theory of constitution组合齿形 composite tooth form组合安装 stack mounting组合机构 combined mechanism阻抗力 resistance最大盈亏功 maximum difference work between plus and minus work 纵向重合度 overlap contact ratio纵坐标 ordinate组合机构 combined mechanism最少齿数 minimum teeth number最小向径 minimum radius作用力 applied force坐标系 coordinate frame。
机械设计专业英语
机械设计专业英语圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation运动粘度kenematic viscosity载荷load载荷—变形曲线load—deformation curve 载荷—变形图load—deformation diagram 窄V 带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension 张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact周节pitch周期性速度波动periodic speed fluctuation 周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load 轴向基本额定动载荷basic dynamic axial load rating轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair转速swiveling speed ; rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine 子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work纵向重合度overlap contact ratio纵坐标ordinate组合机构combined mechanism最少齿数minimum teeth number最小向径minimum radius作用力applied force坐标系coordinate frame行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism虚拟现实virtual reality虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; permissible stress 悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism一般化运动链generalized kinematic chain 移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration 应力图stress diagram应力—应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius 圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling外齿轮external gear弯曲应力beading stress弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism 位移displacement位移曲线displacement diagram位姿pose , position and orientation稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite系杆crank arm, planet carrier现场平衡field balancing向心轴承radial bearing向心力centrifugal force相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear谐波传动harmonic driving谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio 行星齿轮装置planetary transmission行星轮planet gear平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator 燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift螺旋角helix angle螺旋线helix ,helical line绿色设计green design ; design for environment马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress 脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion ;wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements 挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise) 啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower 偏置曲柄滑块机构offset slider-crank mechanism拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance可靠度degree of reliability 可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel联组V 带tight-up V belt联轴器coupling ; shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp 尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing 角接触推力轴承angular contact thrust bearing角接触向心轴承angular contact radial bearing角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load 径向基本额定动载荷basic dynamic radial load rating径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism高度系列height series 功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling 滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery 机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design 机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone 分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train 复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism 复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed 变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism 并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing 波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation ; creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing 单万向联轴节single universal joint 单位矢量unit vector当量齿轮equivalent spur gear; virtual gear 当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia 等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design 动压力dynamic reaction动载荷dynamic load。
机械设计单词表简化版
阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion包角angle of contact比例尺scale闭式链closed kinematic chain闭链机构closed chain mechanism变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面粗糙度surface roughness常用机构conventional mechanism; mechanism in common use 车床lathe承载能力bearing capacity尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮联轴器gear coupling齿轮机构gear齿轮轮坯blank齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter 齿形系数form factor重合度contact ratio传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动角transmission angle传动轴transmission shaft从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear打滑slipping带传动belt driving带轮belt pulley刀具cutter低副lower pair底座chassis疲劳）点蚀pitting端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle对称循环应力symmetry circulating stress多项式运动规律polynomial motion额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD飞轮flywheel分度圆reference circle; standard (cutting) pitch circle 分度圆柱螺旋角helix angle at reference cylinder复合铰链compound hinge工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line功率power共轭凸轮conjugate cam构件link滚刀hob滚动轴承rolling bearing滚动轴承代号rolling bearing identification code滚子roller滚子从动件roller follower赫兹公式H. Hertz equation合力resultant force合力矩resultant moment of force横坐标abscissa互换性齿轮interchangeable gears回程return机构mechanism机构运动简图kinematic sketch of mechanism机构组成constitution of mechanism机架frame, fixed link机械machinery基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion极位夹角crank angle between extreme (or limiting) positions 加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram减速器speed reducer渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线蜗杆involute worm渐开线压力角pressure angle of involute交变应力repeated stress交变载荷repeated fluctuating load胶合scoring交错轴斜齿轮crossed helical gears角加速度angular acceleration角速度angular velocity角速比angular velocity ratio截面section节点pitch point节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter紧边tight-side径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向平面radial plane静力static force静载荷static load局部自由度passive degree of freedom绝对速度absolute velocity开式链open kinematic chain可靠性reliability空间运动副spatial kinematic pair力force力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage链chain链传动装置chain gearing链轮sprocket sprocket-wheel sprocket gear chain wheel轮系gear train螺杆screw螺旋副helical pair螺旋角helix angle摩擦角friction angle摩擦力friction force内齿轮internal gear内力internal force逆时针counterclockwise (or anticlockwise)啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action盘形凸轮disk cam疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 平带flat belt平带传动flat belt driving平底从动件flat-face follower平均应力average stress平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears。
机械设计类英语词汇
机械设计类英语词汇A-Babscissa 横坐标absolute dimensional factor 绝对尺寸系数absolute motion 绝对运动absolute velocity 绝对速度acceleration 加速度acceleration analysis 加速度分析acceleration diagram 加速度曲线acme thread form 梯形螺纹actual line of action 实际啮合线addendum 齿顶高addendum circle 齿顶圆adjustable speed motors 调速电动机advance-to return-time ratio 急回系数advance-to return-time ratio 行程速比系数air spring 空气弹簧allowable amount of unbalance 许用不平衡量allowable pressure angle 许用压力角allowable stress; permissible stress 许用应力amount of unbalance 不平衡量amplitude of vibration 振幅analysis of mechanism 机构分析analytical design 解析设计analytical method 分析法angle of contact 包角angular acceleration 角加速度angular contact ball bearing 角接触球轴承angular contact bearing 角接触轴承angular contact radial bearing 角接触向心轴承angular contact thrust bearing 角接触推力轴承angular velocity 角速度angular velocity ratio 角速比anneal 退火annular spring 环形弹簧anti-friction quality 减摩性aperiodic speed fluctuation 非周期性速度波动application factor 工况系数applied force 作用力Archimedes worm 阿基米德蜗杆Arctan 反正切arm 臂部assembly condition 装配条件Assur group 杆组atlas 图册、图谱automation 自动化average stress 平均应力average velocity 平均速度axial contact bearing 轴向接触轴承axial direction 轴向axial internal clearance 轴向游隙axial load 轴向载荷axial load factor 轴向载荷系数axial plane 轴向平面axial thrust load 轴向分力axial tooth profile 轴向齿廓back angle 背锥角back cone distance 背锥距back cone ；normal cone 背锥back-to-back arrangement 背对背安装backlash 侧隙backlash 齿侧间隙backlash 间隙balance 平衡balance of machinery 机械平衡balance of mechanism 机构平衡balance of rotor 转子平衡balance of rotors 回转体平衡balance of shaking force 惯性力平衡balancing machine 平衡机balancing mass 平衡质量balancing quality 平衡品质balancing speed 平衡转速balata spring 橡胶弹簧ball 球ball bearing 球轴承ball screw 滚珠丝杆band brake 带式制动器barrel (cylindric) cam 圆柱式凸轮步进运动机构base circle 基圆base cone 基圆锥base cylinder 基圆柱base pitch 基圆节距basic dynamic axial load rating轴向基本额定动载荷basic dynamic radial load rating 径向基本额定动载荷basic rating life 基本额定寿命basic static axial load rating 轴向基本额定静载荷basic static radial load tating 径向基本额定静载荷beading stress 弯曲应力bearing alloy 轴承合金bearing block 轴承座bearing bore diameter 轴承内径bearing bush 轴瓦、轴承衬bearing capacity 承载能力bearing capacity factor 承载量系数bearing cup 轴承盖bearing height 轴承高度bearing life 轴承寿命bearing outside diameter 轴承外径bearing ring 轴承套圈bearing width 轴承宽度belleville spring 碟形弹簧belt driving 带传动belt pulley 带轮bending moment 弯矩bevel gear 锥齿轮bevel gears 圆锥齿轮机构bevel pulley; bevel wheel 锥轮bisector 平分线black box 黑箱blank 齿轮轮坯blank 轮坯block diagram 框图blower 鼓风机body guidance mechanism 刚体导引机构bold line 粗线bolts 螺栓bottom clearance 顶隙boundary dimension 外形尺寸brake 制动器buttress thread form 锯齿形螺纹Ccalculated bending moment 计算弯矩cam 凸轮cam , cam mechanism 凸轮机构cam profile 实际廓线cam profile 凸轮廓线cam with oscillating follower 摆动从动件凸轮机构cantilever beam 悬臂梁cantilever structure 悬臂结构Cartesian coordinate manipulator 直角坐标操作器cascade speed control 串级调速case-based design,CBD 基于实例设计center distance 中心距center distance change 中心距变动center of mass 质心center of pressure 压力中心central gear 中心轮centrifugal force 离心力centrifugal force 向心力centrifugal seal 离心密封centrifugal stress 离心应力chain 链chain dotted line 点划线chain gearing 链传动装置chamfer 倒角change gear ; change wheel 变速齿轮characteristics 特性chassis 底座circular gear 圆形齿轮circular pitch 齿距circular pitch; pitch of teeth 节距circular thickness 圆弧齿厚circulating power load 循环功率流clearance 径向间隙clockwise 顺时针closed chain mechanism 闭链机构closed kinematic chain 闭式链clutch 离合器coarse thread 粗牙螺纹coefficient of friction 摩擦系数coefficient of speed fluctuation 机械运转不均匀系数coefficient of speed fluctuation 速度不均匀( 波动) 系数coefficient of travel speed variation 行程速度变化系数coefficient of velocity fluctuation 运转不均匀系数coincident points 重合点combination in parallel 并联式组合combination in series 串联式组合combined efficiency; overall efficiency 总效率combined mechanism 组合机构combined stress 复合应力common apex of cone 锥顶common normal line 公法线compensation 补偿complex mechanism 复杂机构composite tooth form 组合齿形compound (or combined) gear train 复合轮系compound combining 复合式组合compound flat belt 复合平带compound gear train 混合轮系compound hinge 复合铰链Compound screw mechanism 复式螺旋机构compression strength 抗压强度compressive stress 压应力compressor 压缩机computer aided design, CAD 计算机辅助设计computer aided manufacturing, CAM 计算机辅助制造computer integrated manufacturing system, CIMS 计算机集成制造系统concavity 凹面、凹度concept design, CD 方案设计、概念设计concurred design, CD 并行设计concurrent engineering 并行工程condition of self-locking 自锁条件conduction of heat 导热性cone angle 圆锥角cone distance 锥距conjugate cam 共轭凸轮conjugate profiles 共轭齿廓conjugate yoke radial cam 等径凸轮connecting rod, coupler 连杆conoid helical-coil compression spring 圆锥螺旋扭转弹簧constant-breadth cam 等宽凸轮constant-velocity (or double) universal joint 双万向联轴节constitution of mechanism 机构组成constraining force 约束反力constraint 约束constraint condition 约束条件consumption 消耗contact points 啮合点contact ratio 重合度contact seal 接触式密封contact stress 接触应力conventional mechanism; mechanism in common u se 常用机构convex 凸的，凸面体convex roller 球面滚子coordinate frame 坐标系correcting plane 平衡平面correcting plane 校正平面corrosion resistance 耐腐蚀性cosine acceleration (or simple harmonic) motion 余弦加速度运动counterclockwise (or anticlockwise) 逆时针counterweight 平衡重couple 力偶coupler-curve 连杆曲线coupling ; shaft coupling 联轴器crank 曲柄crank angle between extreme (or limiting) position s 极位夹角crank arm, planet carrier 系杆crank shaft 曲轴crank shaper (guide-bar) mechanism 曲柄导杆机构crank-rocker mechanism 曲柄摇杆机构creation design 创新设计critical speed 临界转速cross-belt drive 交叉带传动crossed helical gears 交错轴斜齿轮crown gear 冠轮curvature 曲率curve matching 曲线拼接curved-shoe follower 曲面从动件curvilinear motion 曲线运动cutter 刀具cycle of motion 运动周期cycloidal gear 摆线齿轮cycloidal motion 摆线运动规律cycloidal tooth profile 摆线齿形cycloidal-pin wheel 摆线针轮cylindric pair 圆柱副cylindrical cam 圆柱凸轮cylindrical coordinate manipulator 圆柱坐标操作器cylindrical roller 圆柱滚子cylindrical roller bearing 圆柱滚子轴承cylindrical worm 圆柱蜗杆cylindroid helical-coil compression spring 圆柱螺旋压缩弹簧cylindroid helical-coil extension spring 圆柱螺旋拉伸弹簧cylindroid helical-coil torsion spring 圆柱螺旋扭转弹簧D-Ededendum 齿根高dedendum circle 齿根圆deep groove ball bearing 深沟球轴承deformation 变形degree of freedom, mobility 自由度degree of reliability 可靠度denominator 分母depth of cut 切齿深度derivative 导数design constraints 设计约束design for product`s life cycle, DPLC 面向产品生命周期设计design methodology 设计方法学design variable 设计变量detrimental resistance 有害阻力diameter series 直径系列diametral pitch 径节diametral quotient 蜗杆直径系数diametral quotient 直径系数differential 差速器differential gear train 差动轮系differential screw mechanism 差动螺旋机构differential screw mechanism 微动螺旋机构dimension series 尺寸系列direct (forward) kinematics 正向运动学disc brake 圆盘制动器disc friction clutch 圆盘摩擦离合器disk cam 盘形凸轮disk-like rotor 盘形转子displacement 位移displacement diagram 位移曲线double crank mechanism 双曲柄机构double Haas planer 龙门刨床double rocker mechanism 双摇杆机构double roller chain coupling 滚子链联轴器double row bearing 双列轴承double slider coupling; Oldham‘s coupling 十字滑块联轴器double-direction thrust bearing 双向推力轴承double-slider mechanism, ellipsograph 双滑块机构driven gear 从动轮driven link, follower 从动件driven pulley 从动带轮driven system 传动系统driving force 驱动力driving gear 主动齿轮driving link 原动件driving link 主动件driving moment (torque) 驱动力矩driving pulley 主动带轮dwell 停歇dyad II级杆组dynamic analysis design 动态分析设计dynamic analysis of machinery 机械动力分析dynamic balance 动平衡dynamic balancing machine 动平衡机dynamic characteristics 动态特性dynamic design of machinery 机械动力设计dynamic energy 动能dynamic equivalent axial load 轴向当量动载荷dynamic equivalent radial load 径向当量动载荷dynamic load 动载荷dynamic lubrication 动力润滑dynamic reaction 动压力dynamic viscosity 动力粘度dynamically equivalent model 等效动力学模型dynamics 动力学dynamics of machinery 机械动力学eccentric 偏心盘eccentric mass 偏心质量eccentricity ratio 偏心率effective circle force 有效圆周力effective resistance 工作阻力effective resistance moment 工作阻力矩effective tension 有效拉力elastic coupling ; flexible coupling 弹性联轴器elasticity sliding motion 弹性滑动end-effector 末端执行器energy 能量engagement, mesh, gearing 啮合engaging-in 啮入engaging-out 啮出epicyclic gear train 周转轮系equilibrium 力平衡equivalent 等效量equivalent coefficient of friction 当量摩擦系数equivalent force 等效力equivalent link 等效构件equivalent load 当量载荷equivalent mass 等效质量equivalent mechanism 替代机构equivalent moment of force 等效力矩equivalent moment of inertia 等效转动惯量equivalent spur gear of the bevel gear 锥齿轮的当量直齿轮equivalent spur gear of the helical gear 斜齿轮的当量直齿轮equivalent spur gear; virtual gear 当量齿轮equivalent teeth number; virtual number of teeth 当量齿数evaluation and decision 评价与决策executive link; working link 执行构件external force 外力external gear 外齿轮external loads 工作载荷extreme (or limiting) position 极限位置F-Hface width 平底宽度face-to-face arrangement 面对面安装factor of stress concentration 应力集中系数factored moment; calculation moment 计算力矩fastener 紧固件fatigue limit 疲劳极限fatigue strength 疲劳强度feather key 滑键、导键feedback combining 反馈式组合felt ring seal 毡圈密封ferrofluid seal 铁磁流体密封field balancing 现场平衡fillet radius 圆角半径final contact, end of contact 终止啮合点fine threads 细牙螺纹fixed link; frame 固定构件flange coupling 凸缘联轴器flat belt 平带flat belt driving 平带传动flat leaf spring 板簧flat-face follower 平底从动件flexible automation 柔性自动化flexible impulse; soft shock 柔性冲击flexible manufacturing system; FMS 柔性制造系统flexible rotor 挠性转子flexspline 柔轮fluctuating circulating stress 脉动循环应力fluctuating load 脉动载荷flywheel 飞轮follower dwell 从动件停歇follower motion 从动件运动规律force 力force polygon 力多边形force-drive (or force-closed) cam mechanism 力封闭型凸轮机构forced vibration 强迫振动forge 锻造form cutting 仿形法form factor 齿形系数four-bar linkage 四杆机构frame, fixed link 机架freezing point; solidifying point 凝固点frequency 频率frequency control of motor speed 变频调速frequency converters 变频器frequency of vibration 振动频率friction 摩擦friction angle 摩擦角friction circle 摩擦圆friction force 摩擦力friction moment 摩擦力矩frictional resistance 摩擦阻力full balance of shaking force 惯性力完全平衡function analyses design 功能分析设计function generation 函数生成function generator 函数发生器fundamental mechanism 基础机构fuzzy evaluation 模糊评价fuzzy set 模糊集gas bearing 气体轴承gasket 垫圈gasket seal 垫片密封gear 齿轮gear 齿轮机构gear coupling 齿轮联轴器gear ratio 齿数比gear shaper 插齿机gear train 轮系gear wheel 大齿轮gearing; transmission gear 传动装置general constraint 公共约束generalized coordinate 广义坐标generalized kinematic chain 一般化运动链generating 展成法generating cutting 范成法generating line 发生线generating line of involute 渐开线发生线generating plane 发生面generation mechanism 广义机构Geneva mechanism ；Maltese cross 槽轮机构Geneva numerate 槽数Geneva wheel 槽轮Geneva wheel ; Geneva gear 马耳他机构graphical method 图解法Grashoff`s law 格拉晓夫定理Grashoff`s law 曲柄存在条件green design ; design for environment 绿色设计grey cast iron 灰铸铁grinding wheel groove 砂轮越程槽groove cam 槽凸轮gyroscope 陀螺仪H. Hertz equation 赫兹公式hands of worm 蜗杆旋向harmonic driving 谐波传动harmonic gear 谐波齿轮harmonic generator 谐波发生器heat balance; thermal equilibrium 热平衡height series 高度系列helical bevel gear 螺旋锥齿轮helical gear 斜齿圆柱齿轮helical pair 螺旋副helical torsion spring 扭簧helix ,helical line 螺旋线helix angle 螺旋角helix angle at reference cylinder 分度圆柱螺旋角herringbone gear 人字齿轮high speed belt 高速带higher pair 高副hindley worm 直廓环面蜗杆hinge 铰链、枢纽hob 滚刀hob ,hobbing cutter 齿轮滚刀hollow flank worm 圆弧圆柱蜗杆Hooks coupling ; universal coupling 万向联轴器hour-glass 砂漏hydraulic couplers 液力耦合器hydraulic mechanism 液压机构hydraulic stepless speed changes 液压无级变速hydrodynamic drive 液力传动hyperboloid gear 双曲面齿轮hypoid gear 准双曲面齿轮idle gear 惰轮imbalance (or unbalance) 不平衡in-line slider-crank (or crank-slider) mechanism 对心曲柄滑块机构increment or decrement work 盈亏功inertia force 惯性力infinite 无穷大initial contact , beginning of contact 起始啮合点inner ring 内圈innovation ; creation 创新input link 输入构件instantaneous center 瞬心instantaneous center of velocity 速度瞬心integrate 积分intelligent design, ID 智能化设计interchangeable gears 互换性齿轮interference 干涉intermittent gearing 不完全齿轮机构intermittent motion mechanism 间歇运动机构internal force 内力internal gear 内齿轮inverse ( or backward) kinematics 反向运动学inverse cam mechanism 凸轮倒置机构involute 渐开线involute equation 渐开线方程involute function 渐开线函数involute gear 渐开线齿轮involute helicoid 渐开螺旋面involute profile 渐开线齿廓involute spline 渐开线花键involute worm 渐开线蜗杆jack 千斤顶Jacobi matrix 雅可比矩阵jaw (teeth) positive-contact coupling 牙嵌式联轴器jerk 跃度jerk diagram 跃度曲线jointed manipulator 关节型操作器journal 轴颈kenematic viscosity 运动粘度Kennedy`s theorem 三心定理key 键keyway 键槽kinematic analysis 运动分析kinematic chain 运动链kinematic design 运动设计kinematic design of mechanism 机构运动设计kinematic inversion 反转法kinematic inversion 机架变换kinematic inversion 运动倒置kinematic pair 运动副kinematic precept design 运动方案设计kinematic sketch 运动简图kinematic sketch of mechanism 机构运动简图kinematic synthesis 运动综合kinematical seal 动密封knife-edge follower 尖底从动件labyrinth seal 迷宫密封lathe 车床layout of cam profile 凸轮廓线绘制lead 导程lead 螺纹导程lead angle 导程角lead angle at reference cylinder 分度圆柱导程角leakage 泄漏length of line of action 啮合线长度lift 升距line of action 啮合线line of centers 连心线linear motion 直线运动link 构件linkage 连杆机构lip rubber seal 唇形橡胶密封liquid spring 液体弹簧load 载荷load balancing mechanism 均衡装置load rating 额定载荷load—deformation curve 载荷—变形曲线load—deformation diagram 载荷—变形图loom 织布机lower pair 低副lubricant 润滑剂lubricant film 润滑油膜lubrication 润滑lubrication device 润滑装置machine design; mechanical design 机械设计machinery 机械magnetic fluid bearing 磁流体轴承Maltese cross 马耳他十字manipulator 机器人操作器manipulator 机械手mass 质量mass-radius product 质径积matching 拼接mathematic model 数学模型matrix 矩阵maximum difference work between plus and minu s work 最大盈亏功mean diameter 中径mean screw diameter 平均中径mechanical advantage 机械利益mechanical behavior 机械特性mechanical creation design, MCD 机械创新设计mechanical efficiency 机械效率mechanical speed governors 机械调速mechanical stepless speed changes 机械无级变速mechanical system 机械系统mechanical system design, MSD 机械系统设计mechanical-electrical integration system design 机电一体化系统设计mechanism 机构mechanism 机构学mechanism with flexible elements 挠性机构membership 隶属度metric gears 公制齿轮mid-plane 中间平面milled helicoids worm 锥面包络圆柱蜗杆minimum radius 最小向径minimum teeth number 最少齿数minor diameter 小径modern machine design 机械的现代设计modification coefficient 变位系数modified gear 变位齿轮modified sine acceleration motion 修正正弦加速度运动规律modified trapezoidal acceleration motion 修正梯形加速度运动规律modular design, MD 模块化设计modular system 模块式传动系统modulation, regulation 调节module 模数moment 力矩moment of couple 力偶矩moment of flywheel 飞轮矩moment of inertia ,shaking moment 惯性力矩moment of torque 扭矩morphology box 模幅箱moving link 运动构件multi-diameter shaft 阶梯轴multi-row bearing 多列轴承narrow V belt 窄V带needle roller 滚针needle roller bearing 滚针轴承nominal diameter 公称直径nominal stress 名义应力、公称应力Nomogram 诺模图non-circular gear 非圆齿轮non-contact seal 非接触式密封nonstandard gear 非标准齿轮normal circular pitch 法面齿距normal force 法向力normal load 垂直载荷、法向载荷normal module 法面模数normal parameters 法面参数normal pitch 法向齿距normal plane 法面normal pressure angle 法面压力角normal stress 正应力、法向应力normal tooth profile 法向齿廓number of threads 蜗杆头数number of waves 波数numerator 分子objective function 目标函数offset 偏置式offset circle 偏距圆offset distance 偏( 心) 距offset knife-edge follower 偏置尖底从动件offset roller follower 偏置滚子从动件offset slider-crank mechanism 偏置曲柄滑块机构oil bearing 含油轴承oil bottle 油杯oil can 油壶oil consumption 耗油量oil consumption factor 耗油量系数oily ditch seal 油沟密封Oldham coupling 双转块机构on-net design, OND 网上设计open chain mechanism 开链机构open kinematic chain 开式链open-belt drive 开口传动operation control device 操纵及控制装置operation mechanism 工作机构optimal design 优化设计ordinary gear train; gear train with fixed axes 定轴轮系ordinate 纵坐标original mechanism 原始机构oscillating bar 摆杆oscillating follower 摆动从动件oscillating guide-bar mechanism 摆动导杆机构other mechanism in common use 其他常用机构outer ring 外圈output link 输出构件output mechanism 输出机构output shaft 输出轴output torque 输出力矩output work 输出功overlap contact ratio 纵向重合度packer 打包机paired mounting 成对安装parabolic motion 抛物线运动parabolic motion; constant acceleration and deceleration motion 等加等减速运动规律parallel combined mechanism 并联组合机构parallel helical gears 平面轴斜齿轮parallel key 普通平键parallel mechanism 并联机构parameterization design, PD 参数化设计partial balance of shaking force 惯性力部分平衡passive degree of freedom 局部自由度path generation 轨迹生成path generator 轨迹发生器pawl 棘爪pedal 踏板periodic speed fluctuation 周期性速度波动phase angle of unbalance 不平衡相位pin 销pinion 小齿轮pinion and rack 齿轮齿条机构pinion cutter; pinion-shaped shaper cutter 齿轮插刀pinion unit 齿轮传动系pitch 周节pitch circle 节圆pitch cone 节圆锥pitch cone angle 节圆锥角pitch curve 理论廓线pitch curve 凸轮理论廓线pitch diameter 节圆直径pitch line 节线pitch point 节点pitting （疲劳）点蚀planar cam 平面凸轮planar cam mechanism 平面凸轮机构planar kinematic pair 平面运动副planar linkage 平面连杆机构planar mechanism 平面机构planar pair, flat pair 平面副planet gear 行星轮planetary differential 封闭差动轮系planetary drive with small teeth difference 少齿差行星传动planetary gear train 行星轮系planetary speed changing devices 行星轮变速装置planetary transmission 行星齿轮装置plasticine 橡皮泥pneumatic mechanism 气动机构pointing; cusp 尖点polar coordinate manipulator 球坐标操作器poly V-belt 多楔带polynomial motion 多项式运动规律pose , position and orientation 位姿positive-drive (or form-closed) cam mechanism 形封闭凸轮机构potted component 密封元件powder metallurgy 粉末合金power 功率power screw 螺旋传动power spring 涡圈形盘簧preload 预紧力pressure 压力pressure angle 压力角pressure angle of base circle 基圆压力角pressure angle of involute 渐开线压力角prime mover 原动机primer mover 原动机prismatic joint 移动关节prismatic pair, sliding pair 移动副productive resistance 生产阻力pulsating stepless speed changes 脉动无级变速punch 冲床quadrant 象限quick-return mechanism 急回机构quick-return motion 急回运动raceway 滚道rack 齿条rack cutter; rack-shaped shaper cutter 齿条插刀rack gear 齿条传动radial (or in-line ) roller follower 对心滚子从动件radial (or in-line ) translating follower 对心直动从动件radial bearing 向心轴承radial contact bearing 径向接触轴承radial direction 径向radial internal clearance 径向游隙radial load 径向载荷radial load factor 径向载荷系数radial plane 径向平面radial reciprocating follower 对心移动从动件radius of base circle 基圆半径radius of curvature 曲率半径radius of roller 滚子半径ratchet 棘轮ratchet mechanism 棘轮机构rating life 额定寿命reciprocating follower 移动从动件reciprocating motion 往复移动reciprocating seal 往复式密封reduction gear 减速齿轮、减速装置reduction ratio 减速比redundant (or passive) constraint 虚约束redundant degree of freedom 冗余自由度reference circle; standard (cutting) pitch circle 分度圆reference cone; standard pitch cone 分度圆锥reference line; standard pitch line 分度线regulator, governor 调速器relative gap 相对间隙relative motion 相对运动relative velocity 相对速度reliability 可靠性reliability design, RD 可靠性设计repeated fluctuating load 交变载荷repeated stress 交变应力residual stress 残余应力resistance 阻抗力resultant bending moment 合成弯矩resultant force 合力resultant force 总反力resultant moment of force 合力矩resultant moment of inertia 惯性主矩resultant vector of inertia 惯性主失return 回程revolute (turning) pair 转动副revolute joint 转动关节revolving shaft 转轴Reynolds‘s equation 雷诺方程right triangle 直角三角形rigid bearing 刚性轴承rigid circular spline 刚轮rigid coupling 刚性联轴器rigid impulse (shock) 刚性冲击rigid rotor 刚性转子ring gear 内齿圈rise 升程rise 推程rivet 铆钉robot 机器人robotics 机器人学robust design 稳健设计rocker 摇杆roller 滚子roller bearing 滚子轴承roller chain 滚子链roller clutch 滚柱式单向超越离合器roller follower 滚子从动件rolling bearing 滚动轴承rolling bearing identification code 滚动轴承代号rolling element 滚动体rotary motion 旋转运动rotating seal 旋转式密封rotor 转子rotor with several masses 多质量转子round belt 圆带round belt drive 圆带传动rubber-cushioned sleeve bearing coupling 弹性套柱销联轴器running torque 旋转力矩afety factor; factor of safety 安全系数scale 比例尺scoring 胶合screw 螺杆screw efficiency 螺纹效率screw mechanism 螺旋机构screw nut 螺母screws 螺钉seal 密封seal belt 密封带seal gum 密封胶sealing arrangement 密封装置section 截面self-aligning ball bearing 调心球轴承self-aligning bearing 调心轴承self-aligning roller bearing 调心滚子轴承self-locking 自锁series combined mechanism 串联式组合机构serration spline 三角形花键shaft 轴shaft angle 轴角shaft collar 轴环shaft end ring 轴端挡圈shaft shoulder 轴肩shaking couple 振动力矩shaper 牛头刨床shockproof device 防振装置shocks; shock-absorber 缓冲装置silent chain 齿形链、无声链simple harmonic motion 简谐运动sine generator, scotch yoke 正弦机构single row bearing 单列轴承single universal joint 单万向联轴节single-direction thrust bearing 单向推力轴承singular position 奇异位置six-bar linkage 六杆机构slack-side 松边sleeve 套筒slider 滑块slider-crank (or crank-slider) mechanism 曲柄滑块机构sliding bearing 滑动轴承sliding ratio 滑动率slipping 打滑solid lubricant 固体润滑剂spacewidth 齿槽宽spatial cam 空间凸轮机构spatial kinematic chain 空间运动链spatial kinematic pair 空间运动副spatial linkage 空间连杆机构spatial mechanism 空间机构special kinematic chain 特殊运动链specific heat capacity 比热容speed change 变速speed control system 调速系统speed fluctuation 速度波动speed governing 调速speed reducer 减速器speed-changing gear boxes 齿轮变速箱sphere-pin pair 球销副spheric pair 球面副spherical involute 球面渐开线spherical motion 球面运动spindle 心轴spiral bevel gear 曲齿锥齿轮spiral seal 螺旋密封spline 花键spontaneous ignition 燃点sprocket ; sprocket-wheel ; sprocket gear ; 链轮spur gear 直齿圆柱齿轮square threaded form 矩形螺纹square-jaw positive-contact clutch 矩形牙嵌式离合器stack mounting 组合安装standard gear 标准齿轮standard spur gear 标准直齿轮starting period 起动阶段starting torque 启动力矩static balance 静平衡static equivalent axial load 轴向当量静载荷static equivalent radial load 径向当量静载荷static force 静力static load 静载荷static seal 静密封steady motion period 稳定运转阶段step pulley 塔轮stepless speed changes devices 无级变速装置stiffness coefficient 刚度系数stopping phase 停车阶段straight bevel gear 直齿锥齿轮straight shaft 直轴straight sided normal worm 法向直廓蜗杆stress amplitude 应力幅stress concentration 应力集中stress diagram 应力图stress-strain diagram 应力—应变图structural design 结构设计structure 结构studs 双头螺柱sub-mechanism 子机构subroutine 子程序sun gear 太阳轮sunk key 嵌入键superficial mass factor 表面质量系数surface coefficient of heat transfer 表面传热系数surface roughness 表面粗糙度swiveling speed ; rotating speed 转速symmetry circulating stress 对称循环应力synchronous belt 同步带synchronous belt drive 同步带传动synthesis of mechanism 机构综合taper key 斜键、钩头楔键tapered roller 圆锥滚子tapered roller bearing 圆锥滚子轴承technical and economic evaluation 技术经济评价technique process 技术过程technique system 技术系统technological design 工艺设计tension 张紧力tension pulley 张紧轮theoretical line of action 理论啮合线theory of constitution 组成原理theory of machines and mechanisms 机械原理thickness on pitch circle 节圆齿厚thread (of a screw) 螺纹thread pitch 螺距three-dimensional cam 三维凸轮thrust ball bearing 推力球轴承thrust bearing 推力轴承tight-side 紧边tight-up V belt 联组V带toggle mechanism 肘形机构tool withdrawal groove 退刀槽tooth curve 齿廓曲线tooth number 齿数tooth profile 齿廓tooth ratchet mechanism 齿式棘轮机构tooth space 齿槽tooth thickness 齿厚toroid helicoids worm 环面蜗杆torsion stress 扭转应力total contact ratio 总重合度transmission angle 传动角transmission ratio, speed ratio 传动比transmission shaft 传动轴transverse circular pitch 端面齿距transverse contact ratio 端面重合度transverse module 端面模数transverse parameters 端面参数transverse plane 端面transverse pressure angle 端面压力角transverse tooth profile 端面齿廓tribology design, TD 摩擦学设计two-dimensional cam 两维凸轮type selection 选型undercutting 根切undercutting 过度切割undercutting 运动失真uniform motion; constant velocity motion 等速运动规律unit vector 单位矢量useful resistance 有益阻力useless resistance 有害阻力V belt V带V thread screw 三角形螺纹variable voltage control 调压调速vector 矢量velocity 速度velocity diagram 速度曲线vibration 振动vice 台钳、虎钳virtual reality 虚拟现实virtual reality design, VRD 虚拟现实设计virtual reality technology, VRT 虚拟现实技术viscosity 能量指示图wave generator 波发生器wear resistance 耐磨性wedge cam 移动凸轮weight sets 权重集weighting efficient 加权系数whitworth mechanism 转动导杆机构whole depth 全齿高width of flat-face 从动件平底宽度width series 宽度系列wire soft shaft 钢丝软轴woodruff key 半圆键work 功working cycle diagram 工作循环图working pressure angle 啮合角working space 工作空间working stress 工作应力worm 蜗杆worm and worm gear 蜗杆蜗轮机构worm cam interval mechanism 蜗杆形凸轮步进机构worm gear 蜗轮worm gearing 蜗杆传动机构wrench 扳手wrist 腕部。
机械设计专业术语的英语翻译(含模具)
阿基米德蜗杆Archimedesworm安全系数safetyfactor factorofsafety安全载荷safeload凹面、凹度concavity扳手wrench板簧flatleafspring半圆键woodruffkey变形deformation摆杆oscillatingbar摆动从动件oscillatingfollower摆动从动件凸轮机构camwithoscillatingfollower 摆动导杆机构oscillatingguide-barmechanis m摆线齿轮cycloidalgear摆线齿形cycloidaltoothprofile摆线运动规律cycloidalmotion摆线针轮cycloidal-pinwheel包角angleofcontact保持架cage背对背安装back-to-backarrangement背锥backcone；normalcone背锥角backangle背锥距backconedistance比例尺scale比热容specificheatcapacity闭式链closedkinematicchain闭链机构closedchainmechanism臂部arm变频器frequencyconverters变频调速frequencycontrolofmotorspeed变速speedchange变速齿轮changegear changewheel变位齿轮modifiedgear变位系数modificationcoefficient标准齿轮standardgear标准直齿轮standardspurgear表面质量系数superficialmassfactor表面传热系数surfacecoefficientofheattransfer 表面粗糙度surfaceroughness并联式组合combinationinparallel并联机构parallelmechanism并联组合机构parallelcombinedmechanis m并行工程concurrentengineering并行设计concurreddesign,CD不平衡相位phaseangleofunbalance不平衡imbalanceorunbalance不平衡量amountofunbalance不完全齿轮机构intermittentgearing波发生器wavegenerator波数numberofwaves补偿compensation参数化设计parameterizationdesign,PD残余应力residualstress操纵及控制装置operationcontroldevice槽轮Genevawheel槽轮机构Genevamechanism；Maltesecross槽数Genevanumerate槽凸轮groovecam侧隙backlash差动轮系differentialgeartrain差动螺旋机构differentialscrewmechanism差速器differential常用机构conventionalmechanism mechanis mincommonuse 车床lathe承载量系数bearingcapacityfactor承载能力bearingcapacity成对安装pairedmounting尺寸系列dimensionseries齿槽toothspace齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendumcircle齿根高dedendum齿根圆dedendumcircle齿厚tooththickness齿距circularpitch齿宽facewidth齿廓toothprofile齿廓曲线toothcurve齿轮gear齿轮变速箱speed-changinggearboxes齿轮齿条机构pinionandrack齿轮插刀pinioncutter pinion-shapedshapercutter 齿轮滚刀hob,hobbingcutter齿轮机构gear齿轮轮坯blank齿轮传动系pinionunit齿轮联轴器gearcoupling齿条传动rackgear齿数toothnumber齿数比gearratio齿条rack齿条插刀rackcutter rack-shapedshapercutter 齿形链、无声链silentchain齿形系数formfactor齿式棘轮机构toothratchetmechanism插齿机gearshaper重合点coincidentpoints重合度contactratio冲床punch传动比transmissionratio,speedratio传动装置gearing transmissiongear传动系统drivensystem传动角transmissionangle传动轴transmissionshaft串联式组合combinationinseries串联式组合机构seriescombinedmechanism 串级调速cascadespeedcontrol创新innovation creation创新设计creationdesign垂直载荷、法向载荷normalload唇形橡胶密封liprubberseal磁流体轴承magneticfluidbearing从动带轮drivenpulley从动件drivenlink,follower从动件平底宽度widthofflat-face从动件停歇followerdwell从动件运动规律followermotion从动轮drivengear粗线boldline粗牙螺纹coarsethread大齿轮gearwheel打包机packer打滑slipping带传动beltdriving带轮beltpulley带式制动器bandbrake单列轴承singlerowbearing单向推力轴承single-directionthrustbearing 单万向联轴节singleuniversaljoint单位矢量unitvector当量齿轮equivalentspurgear virtualgear当量齿数equivalentteethnumber virtualnumberofteeth当量摩擦系数equivalentcoefficientoffriction当量载荷equivalentload刀具cutter导数derivative倒角chamfer导热性conductionofheat导程lead导程角leadangle等加等减速运动规律parabolicmotion constantaccelerationanddecelerationmotion 等速运动规律uniformmotion constantvelocitymotion等径凸轮conjugateyokeradialcam等宽凸轮constant-breadthcam等效构件equivalentlink等效力equivalentforce等效力矩equivalentmomentofforce等效量equivalent等效质量equivalentmass等效转动惯量equivalentmomentofinertia等效动力学模型dynamicallyequivalentmodel底座chassis低副lowerpair点划线chaindottedline疲劳点蚀pitting垫圈gasket垫片密封gasketseal碟形弹簧bellevillespring顶隙bottomclearance定轴轮系ordinarygeartrain geartrainwithfixedaxes 动力学dynamics动密封kinematicalseal动能dynamicenergy动力粘度dynamicviscosity动力润滑dynamiclubrication动平衡dynamicbalance动平衡机dynamicbalancingmachine动态特性dynamiccharacteristics动态分析设计dynamicanalysisdesign动压力dynamicreaction动载荷dynamicload端面transverseplane端面参数transverseparameters端面齿距transversecircularpitch端面齿廓transversetoothprofile端面重合度transversecontactratio端面模数transversemodule端面压力角transversepressureangle锻造forge对称循环应力symmetrycirculatingstress对心滚子从动件radialorin-linerollerfollower对心直动从动件radialorin-linetranslatingfollower对心移动从动件radialreciprocatingfollower对心曲柄滑块机构in-lineslider-crankorcrank-slidermechanis m 多列轴承multi-rowbearing多楔带polyV-belt多项式运动规律polynomialmotion多质量转子rotorwithseveralmasses惰轮idlegear额定寿命ratinglife额定载荷loadratingII级杆组dyad发生线generatingline发生面generatingplane法面normalplane法面参数normalparameters法面齿距normalcircularpitch法面模数normalmodule法面压力角normalpressureangle法向齿距normalpitch法向齿廓normaltoothprofile法向直廓蜗杆straightsidednormalworm法向力normalforce反馈式组合feedbackcombining反向运动学inverseorbackwardkinematics反转法kinematicinversion反正切Arctan范成法generatingcutting仿形法formcutting方案设计、概念设计conceptdesign,CD防振装置shockproofdevice飞轮flywheel飞轮矩momentofflywheel非标准齿轮nonstandardgear非接触式密封non-contactseal非周期性速度波动aperiodicspeedfluctuation 非圆齿轮non-circulargear粉末合金powdermetallurgy分度线referenceline standardpitchline分度圆referencecircle standardcuttingpitchcircle 分度圆柱导程角leadangleatreferencecylinder 分度圆柱螺旋角helixangleatreferencecylinder 分母denominator分子numerator分度圆锥referencecone standardpitchcone分析法analyticalmethod封闭差动轮系planetarydifferential复合铰链compoundhinge复合式组合compoundcombining复合轮系compoundorcombinedgeartrain复合平带compoundflatbelt复合应力combinedstress复式螺旋机构Compoundscrewmechanis m复杂机构complexmechanism杆组Assurgroup干涉interference刚度系数stiffnesscoefficient刚轮rigidcircularspline钢丝软轴wiresoftshaft刚体导引机构bodyguidancemechanism刚性冲击rigidimpulseshock刚性转子rigidrotor刚性轴承rigidbearing刚性联轴器rigidcoupling高度系列heightseries高速带highspeedbelt高副higherpair格拉晓夫定理Grashoff`slaw根切undercutting公称直径nominaldiameter高度系列heightseries功work工况系数applicationfactor工艺设计technologicaldesign工作循环图workingcyclediagram工作机构operationmechanis m工作载荷externalloads工作空间workingspace工作应力workingstress工作阻力effectiveresistance工作阻力矩effectiveresistancemoment 公法线commonnormalline公共约束generalconstraint公制齿轮metricgears功率power功能分析设计functionanalysesdesign共轭齿廓conjugateprofiles共轭凸轮conjugatecam构件link鼓风机blower固定构件fixedlink frame固体润滑剂solidlubricant关节型操作器jointedmanipulator惯性力inertiaforce惯性力矩momentofinertia,shakingmoment 惯性力平衡balanceofshakingforce惯性力完全平衡fullbalanceofshakingforce 惯性力部分平衡partialbalanceofshakingforce 惯性主矩resultantmomentofinertia惯性主失resultantvectorofinertia冠轮crowngear广义机构generationmechanis m广义坐标generalizedcoordinate轨迹生成pathgeneration轨迹发生器pathgenerator滚刀hob滚道raceway滚动体rollingelement滚动轴承rollingbearing滚动轴承代号rollingbearingidentificationcode 滚针needleroller滚针轴承needlerollerbearing滚子roller滚子轴承rollerbearing滚子半径radiusofroller滚子从动件rollerfollower滚子链rollerchain滚子链联轴器doublerollerchaincoupling滚珠丝杆ballscrew滚柱式单向超越离合器rollerclutch过度切割undercutting函数发生器functiongenerator函数生成functiongeneration含油轴承oilbearing耗油量oilconsumption耗油量系数oilconsumptionfactor赫兹公式H.Hertzequation合成弯矩resultantbendingmoment合力resultantforce合力矩resultantmomentofforce黑箱blackbox横坐标abscissa互换性齿轮interchangeablegears花键spline滑键、导键featherkey滑动轴承slidingbearing滑动率slidingratio滑块slider环面蜗杆toroidhelicoidsworm环形弹簧annularspring缓冲装置shocks shock-absorber灰铸铁greycastiron回程return回转体平衡balanceofrotors混合轮系compoundgeartrain积分integrate机电一体化系统设计mechanical-electricalintegrationsystemdesign 机构mechanis m机构分析analysisofmechanis m机构平衡balanceofmechanism机构学mechanism机构运动设计kinematic内方头紧定螺钉n.square-socket set-screw开槽锥端紧定螺钉Slotted set screws with cone point锥销锁紧挡圈Lock rings with cone pin螺钉锁紧挡圈Lock ring with screw限位钉stop pin限位块stop button热敏电阻器预留空hole for thermistor带隔离板的注模浇口Injection gate plane with isolation plate浇模和注模器的温度隔板T emperature isolation plate at injection and injector 拔模锥度（的定位）销draft pins注模插件和分离（夹层）打磨Moulding inserts and partings grinded定距拉杆length bolt定距拉板puller bolt一模多穴Multi-Cavity流道凝料condensed material in runner利用率utilization ratio自动脱螺纹automatic thread demoulding 、motorized thread unwinding, 生产现场Production scene车间workshop生产线production line模具专业英语入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate 圆形流道：round(full/half runner流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue 热流道板：hot manifold发热管：cartridge heater 探针: thermocouples插头：connector plug 插座：connector socket密封/封料：seal三、运水：water line 喉塞：line lpug喉管：tube塑胶管：plastic tube 快速接头：jiffy quick connectorplug/socker四、模具零件：mold components三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing中托司：shoulder guide bushing 中托边L：guide pin顶针板：ejector retainner plate 托板：support plate螺丝：screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity inter-lock顶针：ejector pin 司筒：ejector sleeve司筒针：ejector pin 推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）：mold base 上内模：cavity insert下内模：core insert 行位（滑块）：slide镶件：insert 压座/斜鸡：wedge耐磨板/油板：wedge wear plate 压条：plate撑头: support pillar 唧嘴：sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch 扣鸡：parting lock set推杆：push bar 栓打螺丝：S.H.S.B顶板：eracuretun 活动臂：lever arm分流锥：spure sperader 水口司:bush垃圾钉：stop pin 隔片：buffle弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin镶针：pin 销子：dowel pin波子弹弓：ball catch模具成形不良用语英汉对照aberration 色差atomization ?化bank mark ?料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜low hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模各种模具常用成形方式英汉对照accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模机械类常用英语：冲压模具-零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块机械类常用英语：冲压模具-模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板冲压模具-冲压名称类英汉对照plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量。
机械设计制造及其自动化专业英语翻译超级大全
机械设计制造及其自动化专业英语翻译超级大全Mechanical Design, Manufacturing, and Automation机械 design：机械设计Manufacturing：制造Automation：自动化机械设计、制造和自动化是一个涵盖工程和技术各个方面的多学科领域。
它涉及到机械、工具和系统的设计、开发和生产，以促进工业过程。
机械设计是指创造和优化机械系统、零部件或产品的形态、结构和功能的过程。
这涉及到构思想法、进行分析和计算，并利用计算机辅助设计软件（CAD）创建详细设计。
机械设计还涉及选材、考虑制造方法，并确保最终产品符合行业标准和法规。
The manufacturing process involves transforming raw materials into finished products through various techniques and processes. This can include traditional methods such as casting, machining, and assembly, as well as more advanced techniqueslike additive manufacturing (3D printing). Manufacturing also involves quality control measures to ensure that products meet specifications and standards.制造过程涉及通过各种技术和工艺将原材料转化为成品。
这可能包括传统方法，如铸造、机械加工和组装，也包括更先进的技术，如增材制造（3D打印）。
制造还涉及质量控制措施，以确保产品符合规格和标准。
自动化在现代机械设计和制造中发挥着重要的作用。
它利用技术和控制系统在无人干预的情况下操作和控制机械和工序。
机械设计制造及自动化英语
机械设计制造及自动化英语机械工程是一门广泛的工程学科，涉及到机械设计、制造、运行、维护和修理。
在机械工程领域，英语是一种重要的工具语言。
本文将介绍机械设计制造及自动化领域中常用的英语词汇和短语。
一、机械设计1. Design concept：设计概念2. Design criterion：设计准则3. Design parameters：设计参数4. Design specification：设计规范5. Design optimization：设计优化6. Design verification：设计验证7. Design review：设计评审8. Design modification：设计修改9. Design analysis：设计分析10. Design evaluation：设计评估11. Design documentation：设计文档12. Design drawing：设计图纸二、机械制造1. Manufacturing process：制造工艺2. Manufacturing cost：制造成本3. Manufacturing efficiency：制造效率4. Manufacturing quality：制造质量5. Manufacturing capacity：制造能力6. Manufacturing equipment：制造设备7. Manufacturing technology：制造技术8. Manufacturing standard：制造标准9. Manufacturing tolerance：制造公差10. Manufacturing inspection：制造检验11. Manufacturing maintenance：制造维护12. Manufacturing safety：制造安全三、自动化1. Automation system：自动化系统2. Automation technology：自动化技术3. Automation equipment：自动化设备4. Automation control：自动化控制5. Automation software：自动化软件6. Automation integration：自动化集成7. Automation efficiency：自动化效率8. Automation reliability：自动化可靠性9. Automation maintenance：自动化维护10. Automation safety：自动化安全四、机械设计制造及自动化实例1. CNC machine tool：数控机床2. Gearbox：齿轮箱3. Bearing：轴承4. Hydraulic system：液压系统5. Pneumatic system：气动系统6. Conveyor belt：传送带7. Robot arm：机械臂8. Injection molding machine：注塑机9. Press machine：压力机10. CNC lathe：数控车床以上是机械设计制造及自动化领域中常用的英语词汇和短语。
机械设计专用术语英语(Terminology for mechanical design English)
机械设计专用术语英语（Terminology for mechanical designEnglish）Mechanical engineers, homes, machinery, specialized English, study areas, terminology for mechanical design, EnglishSpecial term for mechanical design EnglishAdmin 2007-4-30 03:11Terminology for mechanical design EnglishArchimedes worm Archimedes wormSafety factor safety factor; factor of safetySafety payload safe loadA concavity, concavityWrench wrenchLeaf springs flat, leaf, springSemicircle key woodruff keyDeformation deformationPendulum rod oscillating barOscillating follower oscillating, followerOscillating follower cam mechanism cam, with, oscillating, followerOscillating guide rod mechanism oscillating, guide-bar, mechanismCycloid gear cycloidal gearCycloid gear cycloidal, tooth, profileMotion law of cycloid cycloidal motionCycloidal pin cycloidal-pin wheelWrap angle angle of contactHolder cageTo install back-to-back arrangementBack cone back cone; normal coneBack cone angle back angleBack cone distance back, cone, distanceScale scaleSpecific heat capacity specific heat capacityClosed chain closed, kinematic, chainClosed chain mechanism closed chain mechanismArm armFrequency converter frequency convertersVariable frequency speed regulation frequency, control, of, motor, speedVariable speed speed changeVariable gear change, gear, change, wheelAddendum gear modified gearDeflection coefficient modification coefficientStandard gear standard gearStandard straight gear standard, spur, gearSurface quality coefficient superficial, mass, factorSurface heat transfer coefficient surface, coefficient, of, heat, transferSurface roughness surface, roughnessParallel combination combination in parallelParallel mechanism parallel mechanismParallel combination mechanism parallel, combined, mechanism Concurrent engineering, concurrent, engineeringParallel design, concurred, design, CDUnbalanced phase phase, angle, of, unbalanceUnbalanced imbalance (or, unbalance)Unbalance quantity amount, of, unbalanceIncomplete gear mechanism intermittent gearingWave generator wave generatorWave number number, of, wavesCompensation compensationParametric design, parameterization, design, PDResidual stress residual, stressControl and control device operation control device Grooved wheel Geneva wheel槽轮机构geneva Maltese Cross mechanism;槽数geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential Gear train差动螺旋机构differential Screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing Capacity成对安装paired mounting尺寸系列dimension Series齿槽tooth Space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum Circle齿根高dedendum齿根圆dedendum Circle齿厚tooth Thickness齿距circular pitch齿宽face width齿廓tooth Profile齿廓曲线tooth Curve齿轮gear齿轮变速箱speed Changing Gear Boxes齿轮齿条机构pinion and Rack齿轮插刀pinion Pinion cutter; shaped Shaper Cutter 齿轮滚刀hob, Hobbing Cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion Unit齿轮联轴器gear coupling齿条传动rack Gear齿数tooth Conjugates齿数比gear ratio齿条rack齿条插刀rack cutter; rack shaped Shaper Cutter 齿形链、无声链silent Chain齿形系数form factor齿式棘轮机构tooth Ratchet mechanism插齿机gear Shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, Speed ratio传动装置gearing; Transmission Gear传动系统driven System传动角transmission Angle传动轴transmission Shaft串联式组合combination in series串联式组合机构series combined mechanism 串级调速cascade Speed Control创新innovation Creation创新设计creation Design垂直载荷、法向载荷normal load唇形橡胶密封lip Rubber Seal磁流体轴承magnetic Fluid Bearing从动带轮driven Pulley从动件driven Link, follower行业专用术语中英对照 (机械设计类)从动件平底宽度平面宽度从动件停歇追随者居住从动件运动规律从动件运动从动轮从动齿轮粗线粗线粗牙螺纹粗牙螺纹大齿轮齿轮打包机封隔器打滑打滑带传动皮带传动带轮皮带轮带式制动器带式制动器单列轴承单列轴承单向推力轴承单向推力轴承单万向联轴节单万向节单位矢量单位向量当量齿轮当量齿轮；锥齿轮当量齿数当量齿数；当量齿数当量摩擦系数当量摩擦系数当量载荷等效荷载刀具刀导数衍生物倒角倒角导热性热传导导程铅导程角导角等加等减速运动规律抛物线运动；不断的加速和减速运动等速运动规律匀速运动；等速运动等径凸轮共轭凸轮等宽凸轮等宽凸轮等效构件等效环节等效力等效力等效力矩等效力矩等效量等效等效质量等效质量等效转动惯量等效转动惯量等效动力学模型等效动力学模型行政2007-4-30 03:14[专业英语词汇]机械设计专用术语发布时间：2007-04-09 16时52分与底座底盘低副低副点划线链虚线（疲劳）点蚀点蚀垫圈垫片垫片密封密封垫片碟形弹簧碟形弹簧顶隙底间隙定轴轮系普通轮系；定轴轮系动力学动力学动密封动密封动能动态能量动力粘度动态粘度动力润滑动力润滑动平衡动态平衡动平衡机动平衡机动态特性动态特性动态分析设计动态分析设计动压力动态反应动载荷动态负载端面横切面端面参数横向参数端面齿距横向节距端面齿廓端面齿廓端面重合度横向接触比端面模数横向模块端面压力角端面压力角锻造伪造对称循环应力对称循环应力对心滚子从动件径向（或在线）滚子从动件对心直动从动件径向（或在线）直动从动件对心移动从动件径向移动从动件对心曲柄滑块机构直插式曲柄滑块（或曲柄滑块）机制多列轴承多列轴承多楔带多楔带多项式运动规律多项式运动规律多质量转子转子与几个群众惰轮空转齿轮额定寿命额定寿命额定载荷额定负荷二级杆组对子发生线生成线发生面生成平面法面法平面法面参数正常参数法面齿距正常齿距法面模数正常模块法面压力角正常压力角法向齿距普通沥青法向齿廓正常齿廓法向直廓蜗杆直廓蜗杆法向力正常力反馈式组合反馈相结合反向运动学逆运动学（或反向）反转法运动学反演反正切反正切范成法生成切割仿形法成形切削方案设计、概念设计概念设计、CD 防振装置防震装置飞轮飞轮飞轮矩飞轮矩非标准齿轮非标准齿轮非接触式密封非接触式密封非周期性速度波动非周期性速度波动非圆齿轮非圆齿轮粉末合金粉末冶金分度线参考线；标准节线分度圆参考圆；标准（切割）节圆分度圆柱导程角分度圆柱导程角分度圆柱螺旋角分度圆柱螺旋角分母分母分子分子分度圆锥参考标准节锥锥；分析法分析方法封闭差动轮系行星差动复合铰链复合铰链复合式组合化合物结合复合轮系化合物（或联合）的齿轮火车复合平带复合平带复合应力复合应力复式螺旋机构复式螺旋机构复杂机构复杂机制杆组杆组干涉干扰刚度系数刚度系数刚轮刚性圆弧样条钢丝软轴钢丝软轴刚体导引机构刚体导引机构刚性冲击刚性冲击（冲击）刚性转子刚性转子刚性轴承刚性轴承行业专用术语中英对照（机械设计类）刚性联轴器刚性联轴器高度系列高度系列高速带高速带高副高副格拉晓夫定理Grashoff `定律根切根切公称直径公称直径高度系列高度系列功工作工况系数应用系数工艺设计工艺设计工作循环图工作循环图工作机构运行机制工作载荷外部载荷工作空间工作空间工作应力工作应力工作阻力有效电阻工作阻力矩阻力矩公法线公法线公共约束一般约束公制齿轮公制齿轮功率功率功能分析设计功能分析设计共轭齿廓共轭齿廓共轭凸轮共轭凸轮构件链接鼓风机鼓风机固定构件固定连接；框架固体润滑剂固体润滑剂关节型操作器关节机械手惯性力惯性力惯性力矩惯性矩、惯性力矩惯性力平衡平衡惯性力惯性力完全平衡全平衡惯性力惯性力部分平衡惯性力部分平衡惯性主矩产生的惯性矩惯性主失合成矢量的惯性冠轮冠齿轮广义机构生成机制广义坐标广义坐标Trajectory generation path generationTrack generator path generatorHob hobRaceway racewayScroll rolling elementRolling bearings rolling, bearingRolling bearings code rolling, bearing, identification, code Needle roller needle rollerNeedle roller bearings needle, roller, bearingRoller rollerRoller bearings roller, bearingRoller radius radius of rollerRoller follower roller, followerRoller chain roller chainRoller chain couplings double, roller, chain, coupling Ball screw ball screwRoller type one way overrunning clutch roller clutch Over cut undercuttingFunction generator function generatorFunction generates function generationOil bearing oil, bearingFuel consumption oil consumptionFuel consumption coefficient oil, consumption, factor Hertz formula H., Hertz, equationComposite bending moment resultant, bending, moment Resultant forceResultant moment resultant, moment, of, forceBlack box black boxAbscissa abscissaAdmin 2007-4-30 03:16Interchangeable gear interchangeable, gears Spline splineSlide key, guide key, feather, keyJournal bearings sliding, bearingSliding rate sliding ratioSlider sliderEnveloping worm toroid, helicoids, worm Ring spring annular springBuffer device shocks; shock-absorberGrey cast iron grey, cast, ironBackhaul returnRotary balance balance, of, rotorsHybrid gear train compound, gear, train Integral integrateMechatronic systems design, mechanical-electrical, integration, system, designInstitution mechanismInstitutional Analysis analysis, of, mechanismAgency balance balance, of, mechanismInstitution mechanismMechanism movement design kinematic design of mechanismMechanism kinematic sketch kinematic, sketch, of, mechanismAgency synthesis synthesis of mechanismThe organization consists of constitution of mechanismRack frame, fixed linkRack conversion kinematic inversionMachine machineRobot robotRobot manipulator, manipulatorRobotics RoboticsTechnical process technique processTechno economic evaluation, technical, and, economic, evaluationTechnical system technique systemMechanical machinery机械创新设计机械创新设计，MCD机械系统设计机械系统设计，MSD机械机械动力分析动态分析机械动力设计机械动态设计机械机械动力学动力学机械的现代设计现代机械设计机械系统机械系统机械利益机械优势机械平衡机械平衡机械手机械手机械设计机械设计；机械设计机械特性力学行为机械调速机械调速器机械效率机械效率机械原理机械原理速度波动机械运转不均匀系数系数机械无级变速机械无级变速基础机构基本机制基本额定寿命基本额定寿命基于实例设计案例设计，CBD基圆基圆基圆半径基圆半径基圆齿距基节基圆压力角基圆压力角基圆柱基圆柱基圆锥基圆锥急回机构急回机构急回特性急回特性急回系数行程速比系数急回运动急回运动棘轮棘轮棘轮机构棘轮机构棘爪棘爪极限位置极端（或限制）的位置极位夹角曲轴转角之间的极端（或限制）的位置计算机辅助设计计算机辅助设计，CAD计算机辅助制造计算机辅助制造CAM计算机集成制造系统计算机集成制造系统CIMS 计算力矩计算力矩；力矩计算计算弯矩计算弯矩加权系数加权系数加速度加速度加速度分析加速度分析加速度曲线加速度图尖点尖指向；尖底从动件滚子从动件间隙反弹间歇运动机构间歇运动机构减速比减速比减速齿轮、减速装置减速齿轮减速器减速机减摩性抗摩擦质量渐开螺旋面渐开线螺旋面渐开线渐开线渐开线齿廓渐开线齿廓渐开线齿轮渐开线齿轮渐开线发生线生成渐开线发生线渐开线方程渐开线方程渐开线函数渐开线函数渐开线蜗杆渐开线蜗杆渐开线压力角压力角渐开线渐开线花键渐开线花键简谐运动简谐运动键关键键槽键槽交变应力反复应力交变载荷交变载荷交*带传动交叉传动交错轴斜齿轮交错轴斜齿轮胶合评分角加速度角加速度角速度角速度角速比角速度比角接触球轴承角接触球轴承角接触推力轴承推力角接触轴承角接触向心轴承向心角接触轴承角接触轴承角接触轴承铰链、枢纽铰链校正平面校正平面接触应力接触应力接触式密封接触密封阶梯轴阶梯轴结构结构结构设计结构设计截面节节点节点节距齿；齿距节线节线节圆节圆节圆齿厚厚度分度圆节圆直径径节圆锥节锥节圆锥角节锥角解析设计分析设计紧边紧边紧固件扣件径节径节径向径向径向当量动载荷径向当量动载荷径向当量静载荷径向当量静载荷径向基本额定动载荷径向基本额定动载荷径向基本额定静载荷径向基本额定静载荷径向接触轴承径向接触轴承径向平面径向平面径向游隙径向内部游隙径向载荷径向载荷径向载荷系数径向载荷系数径向间隙间隙静力静力静平衡静态平衡静载荷静载荷静密封静密封局部自由度被动自由度矩阵矩阵矩形螺纹矩形螺纹锯齿形螺纹锯齿形螺纹矩形牙嵌式离合器矩形牙嵌式离合器绝对尺寸系数绝对尺寸系数绝对运动绝对运动绝对速度绝对速度均衡装置负载平衡机制抗压强度抗压强度开口传动开口皮带传动开式链开式运动链开链机构开链机构可靠性可*度度可*性可靠性可*性设计可靠性设计、研发空气弹簧空气弹簧空间机构空间机构空间连杆机构空间连杆机构空间凸轮机构空间凸轮空间运动副空间运动副空间运动链空间运动链空转闲置页：[ 1 ]查看完整版本：机械设计专用术语英语百度Powered by Discuz！归档进出？2001-2006 Comsenz Inc.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
81
order
次序，顺序，秩序
82
positi on
位置，职位，立场
83
Black box
黑箱法
84
weight factor
加权系数
85
pair of eleme nt
运动副
86
mach ine
机械
87
mach ine tool
机床
88
gear
齿轮，传动装置
89
aberra nee
思维
24
th in ki ng
思想
25
creati on thinking
创造性思维
26
diverge nt thi nking
发散思维
27
rules of thinking
思维规律
28
thinking type
思维类型
29
con stri ngency
收缩，收敛
30
imagery thinking
63
compleme ntary
互补关系
64
competitive
竞争关系
65
cooperative
协作关系
66
con stra in
约束关系
67
repla nt
移植
68
prin ciple
法则，原则，原理
69
in herit
继承，遗传而得
70
bio nic
仿生
71
bio nics
仿生学
72
con trast
形态学矩阵
58
Axiomatic desig n
公理化设计
59
Stan dard tech niq ues
标准技术
60
Inven tive prin ciples
发明原理
61
Desig n catalogue method
设计目录法
62
Multi-se nsor in tegrati on
多传感器集成
工程设计
9
ingen uity
机灵，独创性，
10
Value Engin eeri ng
价值工程
11
Emotio nal In tellige nt Quotie nt
情商（情绪智商）
12
In tellige nec Quotie nt
智商
13
mutati onism
突变论
14
mutatio n
突变
15
Hale Waihona Puke 组合49disperse
（使）分散，（使）散开
50
scatter
分散，散开，驱散
51
mechatr onics
机电一体化
52
Moti on system
运动系统
53
con troller
控制器
54
driver
驱动器
55
actuator
制动器
56
Function-mea ns tree
功能方法树
57
Morphology matrix
预知性维修
98
inten sity
强度、亮度
99
precisi on
精确，精密度，精度
100
error
错误，过失，误差
矩阵
40
morphology
形态学
41
factor
因素，要素，因数
42
carrier
载体
43
circumsta nee
环境，详情，境况
44
restrict
限制，约束，限定
45
aptitude
恰当，智能，聪明
46
brain power
智能，智囊，智囊团
47
in tegrati on
集成
48
comb in ati on
机械创新设计
序 号
英
文
中文
备
注
1
desig n
设计
2
fun ctio n
功能
3
Desig n Methodology
设计方法学
4
creati on
创造
5
inno vati on
创新
6
creativity
创造力
7
Con ceptual desig n
概念设计
8
Engin eeri ng desig n
形象思维
31
abstract
摘要，概要，抽象
32
abstract thinking
抽象思维
33
logical thi nking
逻辑思维
34
an alyse
分析
35
colligati on
综合，总结…
36
appraise
评价
37
decisi on-mak ing
决策
38
form
形状，形态，外形
39
matrix
对比，对照，差异
73
associati on of ideas
［心理］联想
74
an alogy
类似，类推
75
cause and effect
因果
76
symbolize
象征，用符号表现
77
attribute
属性，品质，特征
78
syn ectics
综摄法
79
reversal
颠倒，反转，反向
80
gradati on
［生物］变异，畸变
90
moveme nt
运动
91
belt pulley
皮带轮
92
beari ng
轴承
93
period
周期
94
support ing
支持地，支撑地
95
break maintenance
故障后维修
96
Time based maintenance
预防性维修
97
Con diti on based maintenance
system theory
系统论
16
in formatio nism
信息论
17
cyber netics
控制论
18
project
计划，方案，工程
19
scheme
方案，图解，摘要
20
eleme nts
原理，基础
21
prin cipium
原理，初步
22
prin ciple
法则，原则，原理
23
thought