nevi XB-8623液体加热器(暖奶器)说明书
电热恒温水浴锅说明书
电热恒温水浴锅
使
用
说
明
书
本公司生产系列化电热恒温水箱产品，可供各医疗单位，医学院校，工矿企业，科研部门的化验室做蒸发，浓缩，及恒温加热，化学药品，生物制品等多种用途。
本公司水箱内胆采用不锈钢板氩弧焊焊制成型，外箱体采用优质钢板冲压成型，表面喷塑，面板也采用不锈钢板冲压而成。
本公司产品采用先进的电子控温装置，具有温度预选功能，使用快捷方便，所需温度一次定点到位。
使用方法：
1、将水箱放在固定平台上，加入一定量的水（最好是软化水），水位高于电热管，
为缩短加热时间可加入适量温水。
2、接通电源将仪表设定在你所需温度绿灯亮表示加热，红灯亮表示恒温。
3、数显水箱采用智能数显仪表，请按仪表使用说明书操做。
注意事项：
本产品使用时必须接有地线以防触电。
本公司产品正常使用情况下质量保修一年。
温度控制器操作说明
●面板说明
●操作
在PID参数设定方式，每按一次“SET”键，将按顺序显示下表参数。
●自整定
当温度控制效果不理想时按”<”键5秒可进人系统自整定功能。
自整定过程中温度会有较大过冲，用户在进行系统自整定前请充分考虑此因素。
●100℃以上显示说明
当温度超过100℃时,以”口”代表左边的”10”,例如102.1℃,显示为”口2.1℃”。
加热器安装使用说明书
液体加热器使用说明书河北南风汽车设备集团有限公司前言感谢您使用南风公司生产的、系列液体加热器产品。
在使用前，请您务必认真阅读使用说明书，它会使您在产品结构、性能、使用和保养等方面得到必要的知识。
正确的使用，适时的保养，将保证加热器使用的可靠性和经济性，延长加热器产品的使用寿命。
液体加热器是与发动机相对独立的采暖设备，即在发动机不启动的情况下，也可以独立达到车厢采暖、除霜的效果。
本系统为全自动控制，具有低温启动，高温停止，重复点火，故障报警停机等功能，具备安全保护装置。
作为客车采暖、除霜设备，它具有热效率高，升温快，污染小，乘坐舒适，无异味，噪音低，不干燥，节约燃油等优点。
液体加热器除具有给车厢采暖、除霜的功能外，还具有给发动机作低温预热启动的功能。
它能自动将发动机内防冻液温度恒定在65℃-80℃之间。
冬季使用本机预热发动机，可显著降低发动机磨损、油耗和大气污染，延长发动机寿命。
对于长途运输单位，它具有良好的使用经济性。
再次感谢您对我们的信任和支持，您对我们产品有什么意见或建议，欢迎来电告之，我们将不胜感激！书中叙述未尽之处以及其他事宜，请您拨打电话：销售部技术部售后服务部传真：更多信息请登录南风公司网站，目录一、产品使用特别注意事项………………………………………………二、控制开关操作方法……………………………………………………三、主要技术参数及工作原理……………………………………………四、使用前的检查事项……………………………………………………五、保养与维护……………………………………………………………六、故障分析与解决方法…………………………………………………七、加热器安装及注意事项………………………………………………附录1、加热器电路接线图附录2、加热器外型安装尺寸图附录3、加热器安装示意图一、产品使用特别注意事项1.在选用循环加热介质时，我公司建议您根据车辆所行驶的最低环境温度选用相应牌号的防冻液。
小白熊恒温调奶器的使用方法是什么
小白熊恒温调奶器的使用方法是什么小白熊恒温调奶器说明书上面记载了产品的一些基本特点，以及小白熊恒温调奶器的常见故障和解决办法。
下面是小编分享的小白熊恒温调奶器的使用方法，一起来看看吧。
小白熊恒温调奶器的使用方法消毒器系列小白熊消毒器的功能特点和产品买点，高温蒸汽消毒，烘干，自动控制，无二次污染;追求质量，专物专用。
小白熊消毒器能快速消毒杀菌，保持清洁，给宝宝的健康多加一倍防护，呵护宝宝的健康成长。
HL-0632(数码显示奶瓶消毒器)功能1 数码显示消毒时间(采用高效发热装置，加水120ML，在9分钟内利用高温水蒸汽，彻底杀灭各种残留奶瓶及用具上的细菌)2 数码显示无菌时间(消毒完成后，消毒内自动保持3小时无菌状态，自动倒计时，数码显示)3 语音提示消毒效果(消毒完毕后，机器以“滴滴”声持续提示)4 超大容积(本品采用超大容积，可一次性消毒六个各种超宽，超高奶瓶及奶嘴)5 分体结构(采用分体结构，便于使用者使用方便彻底清洗加热盘，有效避免在加热盘上形成水垢)6 安全锁扣功能(本品采用独特的安全锁扣设计，紧扣消毒锅顶盖和桶体，一方面有效预防房高温水蒸汽外泄，确保消毒效果，并有效避免对使用者造成烫伤;另一方面，有效避免在搬动过程中顶盖和桶体分开，消毒锅内物件掉落现象)7 一键操作功能(所有消毒过程一键控制，操作简易)常见故障及排除法1灯不亮，数字显示不准：(灯坏，内至芯片设置出现故障)2不消毒，消毒过程中自动停止工作：(组装不到位或底盘没加水，水加的太少，加水不能少于120ml)3清洗注意事项：(使用后应清洗并晾干，底盘不能水直接冲洗，用湿布擦拭即可，桶体可直接冲洗干净)HL-0601(奶瓶消毒&烘干器)功能1消毒烘干二合一(蒸汽消毒：加水100ML，能在短时间内消灭奶瓶及其他用具上的细菌;热风烘干：确保24小时无菌，细菌不再滋生) 2语音提示(消毒完毕后，机器以“哔哔”声音持续提示十五秒钟) 3超大容量(一次可容纳8支奶瓶，吸奶器等哺育用具一次性完全消毒)清洗方便(分体结构，不锈钢底盘消毒后不出黄水，不生锈，建议使用纯净水，若有水垢用醋酸清洗即可)4IQ控制面板(微电脑自动控制，具有时间设定，分20分钟40分钟60分钟，一键完成，延长使用寿命，完成后自动关闭，安全开关保护，熔断体保护)常见故障及排除法1注水后，消毒停止后水没干消毒时间不够：(温控器不准，需更换;发热盘表面水垢太厚，导致温控保护)2指示灯都正常，单发热盘不热：(发热盘坏;继电器损坏;熔断体坏;)3消毒指示灯闪烁(按消毒烘干时)机器不正常：(温控器断路)4消毒时不工作，消毒烘干时直接转为烘干：(电机损坏;电热丝损坏;风门开关损坏;继电器损坏)5底盘生锈(使用的不是不是纯净水，有矿物质易氧化;奶瓶清洗不够干净残留奶汁)HL-0602(微电脑奶瓶消毒器)功能1 蒸汽消毒(能在短暂时间内消灭奶瓶及其它用具上的细菌)2 超大容量(加水100ML一次性可容纳8支奶瓶，吸奶器等哺育用具一次性完成消毒，10分钟蒸汽消毒)3 清洗方便(分体结构，不锈钢底盘消毒后不出黄水，不生锈，建议使用纯净水，若有水垢用醋酸清洗即可)4 IQ控制面板(微电脑自动控制，使用方便，完成消毒后自动关闭，安全开关保护，熔断体保护)常见故障及排除法1 水烧不干，消毒时间不够：(排除法同HL-0601)2 电源指示灯亮，不能正常工作：(白桶摆放位置没压住安全开关;电路板出故障)3 指示灯正常但不发热：(熔断体损坏;发热盘坏)HL-0603 功能1防止二次污染(底盘加有防污水槽避免奶渍奶垢在消毒过程中再次流入加热盘中)2握柄(人性化设计，便于搬动，防止滑落)3清洗方便(分体结构，不锈钢底盘消毒后不出黄水，不生锈，建议使用纯净水，若有水垢用醋酸清洗即可)4体积小容量大(实惠实用，一次性可容纳大小4支奶瓶，吸奶器等哺育用具。
海洛克加热器产品说明书
Hydronic Unit Heater Steam Rig HeaterThis manual covers installation, maintenance,repair, and replacement parts.Industrial GradeHeat-Exchanger Unit HeatersPart No. SRH2HUH2-NA-OM-APrinted in CanadaWARNING!Please adhere to all instructions published in this manual. Failure to do so may be dangerous and may void your warranty.The heat-exchanger core is not field repairable.Contact factory for a replacement core if fluid leakage occurs.^ NEMA motors are to be operated at ±10% of the nameplate voltage. If the motor is marked 208-230V the tolerance must be calculated from 230V. If the motor is marked 230V it is still suitable for 208V operation but the tolerance must be calculated from 230V. For 3-phase motors the line to line full load voltage must be balanced within 1%. †Thread-on fittings. Shipped loose and must be installed on site. C3 connection also includes C2 connection. ◊ Other voltages / frequencies available upon request. Longer lead times may apply. Contact factory* Standard Marathon NEMA ex-proof motor is suitable for Class I & II, Div. 1 & 2, Groups C, D, F & G; T3B.Heater Model Code & Option CodesModel CodingModel CodeOption CodesPhysical Dimensions (36 inch model)Model12"16"20"24"30"36"Fan Diameter inch (mm) 12 (304.8) 16 (406.4) 20 (508.0) 24 (609.6) 30 (762.0) 36 (914.4) Air Delivery* CFM (m 3/hr) 1090 (1852) 1650 (2803) 3000 (5097) 3800 (6456) 5500 (9344) 8350 (14186)Approx. Air Velocity* FPM (m/s) 1305 (6.6) 1111 (5.6) 1309 (6.6) 1138 (5.8) 1066 (5.4) 928 (4.7) Air Throw* @ 15 psi steam ft (m) 45 (13.7)65 (19.8)70 (21.3)80(24.4)85 (25.9)70 (21.3)Motor Power HP (Watts)1/4 (186) or 1/3 (248) 1/2 (373)1/2 (373) 3/4 (559)1 (746)Rec. Min. Mounting Height ft (m) 7.5 (2.3) 7.5 (2.3) 7.5 (2.3) 7.5 (2.3)7.5 (2.3)7.5 (2.3)Specifications By Model Size - North American Heaters - 60Hz* At 70°F (21°C), 60 Hz and sea level.Pressure Equipment Approvals SRH2: North America - CRN: 0H14931.2C - steam.HUH2: North America - CRN: 0H14933.2C - steam or fluids.Heater Core Maximum Pressure Rating SRH2 = 150 psig (1034 kPa). HUH2 = 400 psig (2758 kPa).Heater Core MaximumDesign Temp.550 °F (288°C).Heater Core Minimum DesignMetal Temp.-20°F (-29°C).Cabinet Material 14-gauge (0.075") (1.9 mm) steel. 36" model is 12-gauge (0.105") (2.7 mm) steel. Epoxy/polyester powder coated.Louver Blades Anodized extruded aluminum.Fan Spark-resistant aluminumFan Guard Split design with close wire spacing. A Ø3/8" (9.5 mm) probe will not enter.Motor Drive Thermally protected permanently lubricated ball bearing type. (36" model comes with maintenance free speed reducer).Mounting Holes 5/8"-11 UNC: 4 holes at top of heater (12" model has only 2 holes).Fluid Connections Standard: 2" NPT female inlet and outlet (configuration of fluid connection locations can be reversed by rotating the core). Other connection types are available (see model code chart).Header Material 12 gauge (0.105")(2.7 mm) and 3/16" (4.8 mm) carbon steel plate conforming to ASME requirements.Finned Tubes 5/8" (15.9 mm) outside diameter [16-gauge, 0.065" (1.6 mm) wall thickness] carbon steel tubes with 1-1/2" (38.1 mm) outside diameter copper-free, L-foot, tension-wound aluminum fins @ 10 fins per inch.General SpecificationsSRH2 Heaters 12" 16" 20" 24" 30" 36" Net Weight (no options) Lbs (kg) 88 (39.9) 106 (48.1) 149 (67.6) 210 (95.3) 257 (116.6) 482 (218.6) Shipping Weight (no options) Lbs (kg) 138 (62.6) 158 (71.7) 207 (93.9) 275 (124.7) 332 (150.6) 594 (269.4) with 2” NPT nipples (add) Lbs (kg) 1 (0.4) 1 (0.4) 1 (0.4) 1 (0.4) 1 (0.4) 1 (0.4) with flanges & nipples (add) Lbs (kg) 14 (6.3) 14 (6.3) 14 (6.3) 14 (6.3) 14 (6.3) 14 (6.3) HUH2 Heaters12" 16" 20" 24" 30" 36" Net Weight (no options) Lbs (kg) 88 (39.9) 106 (48.1) 149 (67.6) 210 (95.3) 264 (119.7) 491 (222.7) Shipping Weight (no options) Lbs (kg) 138 (62.6) 158 (71.7) 207 (93.9) 275 (124.7) 339 (153.7) 603 (273.5) with 2” NPT nipples (add) Lbs (kg) 1 (0.4) 1 (0.4) 1 (0.4) 1 (0.4) 1 (0.4) 1 (0.4) with flanges & nipples (add) Lbs (kg) 14 (6.3) 14 (6.3) 14 (6.3) 14 (6.3) 14 (6.3) 14 (6.3) Weights - North American Heaters12" 16" 20" 24" 30" 36"Front of Heater (dBA)3 feet 78 78 83 82 90 82 10 feet 71 73 76 76 83 76 15 feet 70 70 74 74 81 74Rear of Heater (dBA)3 feet 78 78 83 82 89 80 10 feet 71 72 77 75 83 76 15 feet 70 71 75 74 81 74ModelNoise Data By Model Size - North American Heaters - 60HzConditions For Safe Use1. Remove any dirt / dust from heater cabinet using a damp cloth to mitigate electrostatic charge buildup.2. Do not install the heater in an environment which could potentially cause an electrostatic charge buildup on the cabinet (i.e. exposure to high pressure steam).3. The heater core is NOT field repairable. All defective cores must be replaced with a factory suppliedunit.4. The motor is NOT field repairable. All defective motors must be replaced with a factory supplied orfactory approved unit.5. Flameproof joints are NOT field repairable. Any damaged enclosures/fittings will have to be replacedwith factory approved units.6. For any field repairs use only original factory installed fasteners or factory supplied replacementfasteners.— INSTALLATION —These instructions are to be used as a general guideline only.LocationPlease follow guidelines below for optimum heating results:1. Do not install heaters such that airflow is blocked or impeded by equipment or walls.2. For occupant comfort, position heaters so that air discharge is directed across areas of highest heat loss,such as doors, windows, and outside walls.3. For large areas, arrange heaters such that the air discharge of one heater is directed towards the inlet of thenext heater. This sets up a rotational airflow with air circulation in the central area of the building.4. For equipment freeze protection, direct air discharge at required equipment.5. For large workshops or warehouses it may be acceptable to use fewer, but larger heaters.6. Do not direct air discharge towards a room thermostat.7. Heater inlet and outlet coupling connection locations can be reversed in the field by removing the core,rotating it 180 degrees, and then re-installing it. Cabinet plugs can then be repositioned.Mounting1. A variety of mounting brackets are available from the factory to aid in installation.2. The heater is designed to be installed in an upright and level position. While it may be installed in otherpositions, for steam service, the inlet must be above the outlet and the bottom of the heat exchanger must drain towards the outlet.3. Heaters are designed to be suspended from the top of the cabinet using either two or four 5/8"–11 UNCbolts or threaded rod.4. It is essential that adequate structural support be provided for installation. The mounting structure must bestrong enough to support the heaters weight, provide sufficient stiffness to prevent excessive vibration, and withstand all probable abusive situations such as transportable installations where truck off-loading impacts, etc. may occur.Mounting Heights and Clearances1. To ensure that warm air reaches the floor, heaters are usually mounted 7-1/2 ft. (2.3m) to 12 ft. (3.6 m)above the floor. Heaters may be mounted at higher elevations and still provide warm air at floor level however, the maximum mounting elevation at which this occurs depends on location and operational conditions.2. Louvers may be adjusted to provide greater downward deflection of the discharge air. However, it isrecommended that louvers not be set <15° from the closed position.Fan Clearance1. Verify the minimum required clearance between fan blades / fan shroud and the fan blades / fan guard priorto heater power up.Heater Size 12" 16" 20" 24" 30" 36"Min Clearance 2.0 mm 2.0 mm 2.5 mm 3.0 mm 3.8 mm 4.6 mm— Piping Practices —1. Steam unit heaters condense steam rapidly, especially during warm-up periods. The return piping must beplanned to keep the heat-exchanger’s core free of condensate during periods of maximum heat output, and steam piping must be able to carry a full supply of steam to the unit heater to take the place of condensed steam. Adequate pipe size is especially important when a unit heater fan is operated under on-off control because the condensate rate fluctuates rapidly.2. Heater is to be connected and serviced only by qualified personnel. For additional piping information referto local codes.3. Eliminate pipe stress by adequately supporting all piping. Do not rely on heater to support piping.4. Take off all branch lines from the top of steam mains, preferably at a 45° angle, although vertical 90°connections are acceptable.5. Pipe the branch supply line into the steam unit heater’s inlet at the top and the return branch line from theoutlet at the bottom. The heater’s inlet and outlet coupling connections can be reversed in the field by rotating the heat-exchanger core. Refer to Page 10, Heat-Exchanger Core AssemblyReplacement.6. In steam systems, the branch from the supply main to the heater must pitch down towards the main and beconnected to its top in order to prevent condensate in the main from draining through the heater. In long branch lines, a drip trap may be needed.7. Allow for pipe expansion to prevent excessive strain on the unit heater’s heat-exchanger core.8. The return piping from steam unit heaters should provide a minimum drop of 10" (254 mm) below theheater so that the pressure of water required to overcome resistances of check valves, traps, and strainers will not cause condensate to remain in the heater.9. In steam systems, where horizontal piping must be reduced in size, use eccentric reducers that permit thecontinuance of uniform pitch along the bottom of piping (in downward pitched systems). Avoid using concentric reducers on horizontal piping, because they can cause water hammer.10. Installing dirt pockets at the outlet of unit heaters and strainers with 0.063 in. (2 mm) perforations to preventrapid plugging are essential to trap dirt and scale that might affect the operation of check valves and traps.Strainers should always be installed in the steam supply line if the heater is valve controlled.11. In steam or hot water systems, rapid air removal is required because entrained air is a cause of corrosion.Hot water systems should be equipped with suitable air vent valves for rapid and complete air removal at high points, at the top of each unit heater, and ends of both supply and return mains. Proper air venting for steam systems can be achieved by use of a steam trap with an internal air vent.12. Steam traps must be located below the outlet of the unit heater. Consult the trap manufacturer for specificrecommendations. Each steam unit heater should be provided with a trap of sufficient size and capacity to pass a minimum of twice the normal amount of condensation released by the unit at the minimumdifferential pressure in the system. Trap capacity is based on the pressure differential between supply and return mains. Steam systems should be equipped with a float and thermostatic trap or inverted bucket trap with an air bypass.13. If the condensate return line is above the heater outlet or is pressurized, install a check valve after thesteam trap and a drain valve at the strainer to drain the system during the off season.14. Install pipe unions and shut-off valves at connection points of each unit heater to allow maintenance orreplacement of unit without shutting down and draining the entire system. For hot water systems include a balancing valve in return line for flow regulation. A drain valve should be provided below each unit heater to allow removal of water from the heat-exchanger core if located in an area subject to freezing.15. Adequate air venting is required for low-pressure closed gravity systems. The vertical pipe connection tothe air vent should be at least 3/4" NPT to allow water to separate from the air passing to the vent. If thermostatic instead of float-and-thermostatic traps are used in vacuum systems, a cooling leg must be installed ahead of the trap.16. In high-pressure systems, it is customary to continuously vent the air through a petcock unless the steamtrap has a provision for venting air. Most high-pressure return mains terminate in flash tanks that are vented to the atmosphere. When possible, pressure reducing valves should be installed to permit operation of the heaters at low pressure. Steam traps must be suitable for the operating pressure encountered.17. On steam systems where the steam supply to the unit heater is modulated or controlled by a motorizedvalve, a vacuum breaker should be installed between the unit outlet and a float and thermostatic trap.Heat-Exchanger Core Assembly Replacement1. Heat-exchanger core assemblies are heavy and replacement requires two people for safety reasons.2. It is not necessary to dismount unit heater from its support structures to remove the heat-exchanger core assembly. However, it may be advisable in some instances to allow for core assembly removal at ground or bench level.3. Remove the bottom heater cabinet cover which is attached with 6 screws and 3 bolts.4. Support the heat exchanger core assembly, then remove the 4 core bolts on each side of the cabinet (36" models have 6 core bolts).5. Lower the core assembly from heater.6. Reverse the procedure to install replacement core and tighten 4 core bolts to 90 in-lbs (10 N-m) torque, bottom panel screws to 28 in-lbs (3 N-m) , and fan panel bolts to 100 in-lbs (11 N-m) . (36" models have 6 core bolts)Fan, Fan Guard or Motor Replacement1. For replacement of fan or fan guard remove the 4 bolts holding motor to the motor mount. For 36" modelsalso remove speed reducer bolts. If replacing motor only on 36" models, only remove motor mounting bolts and C-face flange bolts.2. Detach two-piece fan guard assembly by removing top and bottom screws that attach the fan guard to thecabinet.3. Remove fan guard pieces through top or bottom. Due to stiffness of fan guards, you may need to removeouter two top or bottom bolts that attach the fan panel to the top or bottom cabinet panels to provide sufficient clearance.4. Lift the motor, (and speed reducer for the 36" model) and fan assembly off the motor mount.5. Loosen fan hub screw and remove fan blade from motor shaft.6. To reassemble, position fan on motor shaft with end of shaft even with face of hub. Ensure the set screw isfacing towards motor and lined up perpendicular to factory-ground flat on motor shaft. This flat is our “Easy-Off” fan blade replacement feature and only comes on motors purchased from Hazloc Heaters. Tighten set screw to 150 in-lbs (17 N-m) torque.7. Place motor, (and speed reducer for the 36" model) and fan assembly onto motor mount and fasten the two-piece fan guards to the cabinet.8. Center fan in the fan-shroud opening. The gap between the fan blades and fan shroud should be even forall fan blades. Ensure the minimum gap is maintained for all blades. See page 6 for minimum gap values. 9. Bolt motor (and speed reducer for the 36" model) to motor mount, tighten nuts to 250 in-lbs (28 N-m)torque. Manually spin the fan blade to ensure it rotates freely before reconnecting heater to power supply. Fan must rotate counterclockwise when viewed from rear of heater.— Repair and Replacement —Item (in-lbs)Fan blade set screw 1505/16 - 18 UNC motor nuts 250 1/4 - 20 UNC core bolts90 Torque Settings1/4 - 20 UNC fan panel bolts 100 5/16 - 18 UNC motor mount bolts 250 #10 - 24 UNC bottom panel & louver blade screws281/4 - 20 UNC fan guard self tapping screws 100 (N-m) 17 28 28 11 11 10 3Note: Heater inlet and outlet coupling connection locations can be reversed in the field by removing the core, rotating it 180 degrees,and then re-installing it. Cabinet plugs can then be repositioned.Item No.Description12 inch16 inch20 inch24 inch30 inchPart NumberPart NumberPart NumberPart NumberPart Number*** Please have heater model & serial number available before calling ***1 Core Kit Contact factory with heater model, size, number of passes and connection typePart #’s 1119 thru 11392 Louver Blade kit 1145 1146 1147 1148 11493 Motor Mount Kit 1151 1152 1153 1154 1155 4 Fan Guard Kit 1157 1158 1159 1160 1161 5 Fan - 5/8 inch hub 116311651167116911716 Motor Kit - 5/8 inch shaft Specify motor voltage, phase, frequency, horsepower and type of enclosure (general purpose or explosion-proof)7 Thread-on 2 inch NPT Nipple1176 8Thread-on 300# Raised Face Flange1177Note: Inlet and outlet couplingconnection locations can be reversed in the field by rotating the core.*All replacement part kits include fasteners12 inch to 30 inch models12 inch to 30 inch modelsItem No.Description36 inchPart Number*** Please have heater model & serial number available before calling ***1Core Kit Contact factory with heater model, size, number of passes and connection typePart #’s 1141 thru 11442Louver Blade Kit 11503 Motor Mount Kit 11564 Fan Guard Kit 1162 5Fan - 5/8 inch hub 11736 Motor Kit - 5/8 inch shaft Specify motor voltage, phase, frequency, horsepower and type of enclosure (general purpose or explosion-proof)7Thread-on 2 inch NPT Nipple 11768 Thread-on 300# Raised Face Flange1177 9Speed Reducer Kit1178Note: Inlet and outlet couplingconnection locations can be reversed in the field by rotating the core .*All replacement part kits include fasteners36 inch model36 inch modelRegular inspection, based on a schedule determined by the amount of dirt in the atmosphere, assures maximum operating economy and heating capacity.Annual Inspection (before each heating season)1. Check all terminal connections, electrical conductors, glands and cables for damage, looseness, defects,fraying, etc. and replace or tighten where applicable.2. Check for fluid leakage from heat-exchanger core. If fluid leakage occurs, remove heater from service andhave the heat-exchanger core replaced by a factory replacement unit. Refer to “Repair and Replacement” section for complete details. Note: This heat-exchanger core is not field repairable.3. Check electrical junction box. Inside of enclosure must be clean, dry, and free from any foreign materials.The cover must also be completely on and tight.4. Check motor shaft bearing play. Replace motor if play is excessive or if motor does not run quietly andsmoothly. Motor bearings are permanently lubricated.5. On 36" models, speed reducer is maintenance free. Check for excessive noise and vibration.6. Check fan. Replace immediately if cracked or damaged. Check the gap between the fan and fan shroudmeets the minimum spacing requirement.7. Check louvers. Louver screws should be tight. Louvers are not to be set <15° of the closed position.8. Check the tightness of all hardware. All nuts and bolts, including mounting hardware, must be tightened totorque settings on Page 10.9. Turn heater motor on for a minimum of 10 minutes. Check for air exiting heater through louvers and smoothrunning of the motor and fan assembly.Periodic Maintenance (before and as required during heating season) 1. Clean the following (remove dust using compressed air):∙ Finned tubes ∙ Fan∙ Fan Shroud ∙ Fan Guard ∙ Motor ∙ Louvers ∙ Cabinet 2. Check the following:∙ Motor / fan assembly (and speed reducer on 36" models) for smooth and quiet operation. ∙ Louvers for proper angle and tightness. ∙ Electrical junction box covers are secure.∙Gap between the fan blade / fan shroud and the fan blade / fan guard meet the minimum spac-ing requirement (see page 6 for minimum values).— Maintenance Program —Date of Maintenance PerformedByMaintenance PerformedDate of Maintenance PerformedByMaintenance PerformedPRINTED IN CANADA ©Copyright 2018The information contained in this manual has been carefully checked and verified for accuracy. Specifica-tions subject to change withoutnotice.Hazloc Heaters is a trademark ofHazloc Heaters Inc.#1, 666 Goddard Ave. NE Calgary, Alberta T2K 5X3 CanadaTel.: +1-403-730-2488 Fax: +1-403-730-2482Customer Toll Free (U.S. & Canada): +1-866-701-Heat (4328) Limited 18-Month WarrantyHazloc Heaters TM warrants all SRH2 & HUH2 series of heat-exchanger unit heaters against defects in materials and workmanship under normal conditions of use for a period of eighteen (18) months from date of pur-chase based on the following terms:1. The heater must not be modified in any way.2. The heater must be stored, installed and used only in accordance with the owner’s manual and attached data plate information.3. Replacement parts will be provided free of charge as necessary to restore any unit to normal operating condition, provided that the defective parts be returned to us freight prepaid and that the replacement parts be accepted freight collect.4. The complete heater may be returned to our manufacturing plant for repair or replacement (at our discretion), freight charges prepaid.5. Components damaged by contamination from dirt, dust, etc. or corrosion will not be considered as defects.6. This warranty shall be limited to the actual equipment involved and, under no circumstances, shall include or extend to installation or removal costs, or to consequential damages or losses.。
恒温水浴锅使用说明
恒温水浴锅使用说明时间：2009-04-06 07:39:48 来源：作者：电热恒温水浴锅使用操作规程•水箱中加入适量水（最好选用蒸馏水），水位高于隔板50mm 以上，否则电热管将被烧坏。
•接通电源，有接地保护，开启电源开关，绿灯亮，黄灯灭，表示加热状态。
•通过温度显示调节仪的温度设定和控制（调节温度精度可用“手动微调RST”），使电热管加热；直至黄灯亮，绿灯灭，表示加热停止，温度达到设定温度。
•产品在使用时操作者不宜长时间远离，工作结束后或遇到停电后，操作者应随手关闭开关或拔掉插头。
注意：使用220V电源。
严禁加热时干烧，以防出现电器事故。
不可将试样洒入水箱内。
放置在无腐蚀性气体的室内。
TDL-5-A型低速台式离心机使用操作规程•离心机置于平台上。
离心管需等量灌注，在转子平衡下运转。
运转前拧紧转头押紧螺母，盖好风罩。
•接好电源，须接地线，开电源开关。
面板显示00000，并闪烁。
按选择键，出现P0000，转速设定；按记忆键，显示上次运转频率，用加键和移位键调至所需频率；按记忆键储存数据，再显示P0000。
按加键，显示P0001，时间设定，同转速方法一样设定工作时间（分钟），按记忆键后再显示P0001。
•按选择键，退出设定。
显示00000并闪烁。
•按离心键，仪器工作并显示实际转速，到设定时间，降速至00000后5秒内打开盖门，取出样品。
如有需要，运行中可按停止键，中断运转。
注意：1、不能在塑料盖上放置任何物品，不能在运转过程中或未停稳的情况下开盖门。
2、转速设定不得超过最高转速，除运转转数和时间外，不要随便更改机器工作参数。
3、离心机一次运转最好不超过60分钟，不用时请拔掉插头。
KXL-1010控温消煮炉使用操作规程•将加热炉放置在通风橱中，温度控制器放置在通风橱外，按要求连接好这两者。
插入温度控制器220V电源插头。
•开温度控制器开关，设置温度控制点。
按（SET）键，SV窗显示个位闪动；按（∨）或（∧）键设置个位；按（<A/M）键，再按（∨）或（∧）设置十位；设置百位同上。
海尔电子发展有限公司智能加热饮水器用户手册说明书
2. Add rinse aid up to the max mark.
max
3. Close the lid of the dispenser for rinse aid. a The lid clicks into position.
washers. Remove large remnants of food from 3. Switch on the appliance .
the tableware. Check that the spray arms can ro-
4. Select the programme. 5. Start the programme . 6. Remove the tableware at the end of the pro-
Programmes
The programme data has been measured in the laboratory according to European standard EN 60436. The consumption figures depend on the programme and additional function selected. The running time will change if the rinse aid system is switched off or rinse aid needs to be added.
gether and lift
1
the coarse filter
out .
Cleaning spray arms
水加热器说明书
JRG-15型水加热器使用说明书一、前言JRG-15型水加热器加热系统使用的新型加热设备，该设备由电加热器本体和控制系统两部分组成。
发热元件采用不锈钢管，0Cr27Al7MO2高温电阻合金丝、结晶氧化镁粉，经压缩工艺成型，使电加热元件的使用寿命得以保证。
控制部分采用高精度数显式温控仪、交流接触器组成可调测温、恒温系统，保证了电加热器的正常运行。
二、技术参数1、JRG-15型水加热器的规格与参数：1、外形尺寸（长×宽×高）：950×400×600mm（1）进出口法兰：DN25（2）进水温度；环境温度（3）出水温度；常温-90℃2、控制柜的主要技术指标数据（1）、输入电压：380/220V±5% 50Hz（三相四线）（2）、加热功率：15KW（3）、额定电流：25A（单相）三、主要结构及工作原理（1）JRG-15型水加热器结构（另附图）JRG-15型水加热器是由多支管状电加热元件、筒体、导流板等几部分组成，管状电热元件是在金属管内放入高温电阻丝，在空隙部分紧密地填入具有良好绝缘性和导热性能的结晶氧化镁粉，采用管状电热元件做发热体，具有结构先进，热效率高，机械强度好，耐腐、耐磨等特点。
筒体内安装了导流隔板，能使水在流通时受热均匀。
（2）工作原理JRG-15型水加热器采用数显温度调节仪、固态继电器和测温元件组成测量、调节、控制回路，在电加热过程中测温元件将水加热器出口温度电信号送至数显温度调节仪进行放大，比较后显示测量温度值，同时控制交流接触器通断，从而控制加热器，使控制柜具有良好的控制精度和调节特性。
详见电气原理图（另附图）。
四、安装与使用控制柜应安装在干燥通风，便于操作的地方。
管道加热器外壳、控制柜外壳应可靠接地，管道加热器应水平安装，底座螺母要拧紧使其稳固。
本体与外接管道安装时，应注意进出口方向。
管道加热器在使用前应测量电源接入端子与金属外壳绝缘电阻不得低于2MΩ，使用环境相对湿度不大于85%。
恒温电热水器使用说明书
ELECTRIC WATER HEATER ASSEMBL Y AND OPERATION INSTRUCTIONSGENERAL SAFETY INSTRUCTIONS1. Read the instructions and warning in this manual carefully, theycontain important information regarding safe installation, use and maintenance.This manual is an integral part of the product. Hand it on to the next user/owner in case of change of property.2. The manufacturer shall not liable for any injury to people, animals ordamage to property caused by improper, incorrect or unreasonable use or failure to follow the instructions reported in this publication.3. Installation and maintenance must be performed by professionallyqualified personnel as specified in the relative paragraphs.Only use original spare parts. Failure to observe the above instruc-tions can compromise the safety of the appliance and relieves the manufacturer of any liability for the consequences.4. DO NOT leave the packaging materials (staples, plastic bags, ex-panded polystyrene, etc.) within the reach of children they can cause serious injury.5. The appliance may not be used by persons under 8 years of age,with reduced physical, sensory or mental capacity, or lacking the requisite experience and familiarity, unless under supervision or following instruction in the safe use of the appliance and the haz-ards attendant on such use. DO NOT permit children to play with the appliance. User cleaning and maintenance may not be done by unsupervised children.6. DO NOT touch the appliance when barefoot or if any part of yourbody is wet.7. Before using the device and after routine or extraordinary mainte-nance, we recommend filling the appliance’s tank with water and draining it completely to remove any residual impurities.8. If the appliance is equipped with a power cord, the latter may onlybe replaced by an authorised service centre or professional tech-nician.9. It is mandatory to screw o the water inlet pipe of the unit a safetyvalve in accordance with national regulations. In countries which have enacted EN 1487, the safety group must be calibrated to a maximum pressure of 1487 MPa (0,7 bar) and include at least a cock,check valve and control, safety valve and hydraulic load cutout. 10. Do not tamper with the overpressure safety device (valve or safetygroup), if supplied together with the appliance; trip it from time to time to ensure that it is not jammed and to remove any scale de-posits.11. It is normal water drips from the overpressure safety device whenthe appliance is heating. For this reason, the drain must be con-nected, always left open to the atmosphere, with a drainage pipe installed in a continuous downward slope and in a place free of ice.12. Make sure you drain the appliance and disconnect it from the pow-er grid when it is out of service in an area subject to subzero tem-peratures.13. Water heated to over 50 °C can cause immediate serious burns ifdelivered directly to the taps. Children, disabled persons and the aged are particularly at risk. We recommend installing a thermostat-ic mixer valve on the water delivery line, marked with a red collar.14. D o not leave flammable materials in contact with or in the vicinity ofthe appliance.15. Do not place anything under the water heater which may be dam-aged by a leak.LEGIONELLA BACTERIALegionella are small rod shaped bacteria which are a natural constituent of all fresh waters. Legionaries’ disease is a pneumonia infection caused by inhaling of Legionella species. Long periods of water stag-nation should be avoided; it means the water heater should be used or flushed at least weekly.The European standard CEN/TR 16355 gives recommendations for good practice concerning the pre-vention of Legionella growth in drinking water installations but existing national regulations remain in force.DESCRIPTION OF WATER HEATER(see figure 7)F) LEDA) CapM) Adjustment knobB) Water intake pipeC) Water outlet pipeTECHNICAL CHARACTERISTICSFor the technical specifications, refer to the nameplate (the nameplate is located next to the water in-take/outlet pipes).This appliance is conforming with the standard SANS 151 and with the electrical safety standards SANS 60335-1 and SANS 60335-2-21* Declared Energy Performance have been achieved by using the hydraulic adaptors supplied with the Water HeaterINSTALLING NORMS (for the installer)The appliance must be installed and commissioned by a qualified technician in accordance with estab-lished regulations and local health and safety regulations.We recommend installing the appliance as close as possible to the delivery points to minimise heat loss along the pipes. Local regulations may provide for restrictions on installation in bathrooms; observe any regulatory minimum distances. The range of water heaters includes models set up to be assembled above or below the point of use (sink, basin or shower). The models intended to be assembled under the point of use are called “undersink”. To facilitate maintenance, make sure there is a clearance of at least 50 cm inside the enclosure for access to the electrical equipment. Fix the supplied bracket to the wall with screws and dowels of adequate size for the type of wall. Hook the water heater to the bracket and pull down to make sure it is secured.HYDRAULIC CONNECTIONThe INSTALLATION of the appliance must strictly comply with SANS 10254 code of practice, a copy of which is obtainable from the South African Bureau of Standards. Installation, maintenance and repairs to the appliance not complying with the SANS 10254 code of practice will invalidate the Warranty.If you decide to install mixer units (taps or shower), purge the pipes of any potentially damaging impuri-ties first. The appliance must not be supplied with water of hardness less than 12°F, nor with especially hard water (greater than 25°F); we recommend installing a water softener, properly calibrated and con-trolled - do not allow the residual hardness to fall below 15°F. Before using the appliance, we recommend filling its tank with water and draining it completely so as to remove any residual impurities.Specific taps must be used for this type of installation and the connection must be implemented as shown in the diagram in Fig. 1. With this solution, the water heater can work at any mains pressure and no type of tap must be connected on the outlet pipe, which acts as a vent.We reccomend that all exposed metal pipes must be lagged.The hydraulic adaptors, which are delivered with the product, must be installed on the thread connection with a sealing.ELECTRICAL CONNECTIONBefore performing any operations, disconnect the appliance from the electricity mains using the external switch.1. Electrical installation must comply with SANS 10142 – Electrical code for wiring of premises and should be tested by the local electricity authority. The fixed wiring must incorporate a means of disconnecting from the main supply having a separation of at least3 mm in all poles.2. Check the circuit breaker on the distribution board is the correct amperage for the unit.3. Check that all electrical connections are secure. with a sealing.4. Replace electrical cover and ensure geyser is full of water before switching on electricity, even for testing purposes.5. Fixed wiring must incorporate a means of disconnecting from the main supply, having a separation of at least 3 mm in a pole.NOTE: Elements burn through commissioning without water and burnouts due to loose connections are not covered by the Warranty.For greater safety, have qualified personnel carry out a careful inspection of the electrical system, ensur-ing it complies with the applicable norms in force, because the appliance manufacturer will not be held responsible for any damage caused by the lack of earthing of the system or for faults in the electricity supply.Check that the system is suitable for the maximum power absorbed by the water heater (please refer to the data plate) and that the cross-section of the electrical connection cables is suitable and complies with current laws. The use of multiplugs, extensions or adaptors is strictly prohibited. It is strictly forbid-den to use the piping from the plumbing, heating and gas systems for the appliance earthing connection. If the appliance is supplied with a power supply cable and the latter should need replacing, use a cable featuring the same characteristics (type H05VV-F 3x1.5 mm², 8.5 mm in diameter) and compliant with SANS 60227-5. The supply cable (type H05 VV-F 3x1.5 mm²) is to be inserted in the proper hole situated in the back of the appliance and slide it until it reaches terminal of the thermostat, then lock single cables by mean of the insulation base. To disconnect the unit from the electrical supply use a bipolar, switch conforming to local (contact opening at least 3 mm, better if equipped with fuses).The appliance must be earthed and the earth cable (which must be yellow-green and longer than that of the phases it is fixed to the terminal marked by the symbol . Block the power supply cord on the small cap using the special wire clamp provided.Before usage, make sure that the supply voltage is in compliance with the rated values of the ap-pliance. If the appliance is not supplied with a power supply cable, use a flexible cable (type H05VVF 3X1.5mm2, 8.5 mm) in diameter compliant with the applicable norms in force, if the applianche is sup-plied with a cable clamp.Startup and commissioningBefore powering up the appliance, fill the heater with mains water.T o do so, open the mains cock and the hot water tap until all the air has been vented from the boiler. Check for leaks from the flanges, tighten down the fittings (not too much!) if necessary (A fig. 4). Power up using the switch and in models with no switch, power up by turning the adjustment knob clockwiseMAINTENANCE REGULATIONS (for competent person)Maintenance work may only be done by qualified technicians (in possession of the regulatory requi-sites). Before requesting for the Technical Assistance to intervene for a suspected fault, check that this is not caused by a temporary lack of water supply or power failure.Draining the applianceMake sure to drain the appliance when it is out of service or in an area subject to subzero temperatures.T o drain the appliance, proceed as follows:- permanently disconnect it from its power supply;- open the hot water tap (sink or bath tub).Replacing partsDisconnect the appliance from its power supply.Remove the enclosure to access the electrical equipment.To work on the thermostat, extract it from its mount and disconnect it from its power supply.To work on the heating element and anode, first drain the appliance.Use only original spare partsScheduled maintenanceThe heating element (R fig. 5) should be descaled every two years to ensure it works properly.If you do not wish to use a liquid descaler, you can simply break off the deposit, taking care not to dam-age the heating element’s cladding. The magnesium anode (N fig. 5) must be replaced every two years; however, the anode should be checked every year if the water is corrosive or chloride rich. To replace it, remove the heating element and unscrew it from its bracket.After routine or extraordinary maintenance, we recommend filling its tank with water and draining it completely so as to remove any residual impurities.Use only original spare parts supplied by the manufacturer’s authorised service centres. Reactivating the two-pole cutoutIf the water overheats excessively, a thermal cutout (CEI-EN compliant) trips to cut the electrical power supply to the heating element (both phases); contact the Service Centre if this occurs.USER INSTRUCTIONSRecommendations- Do not place anything under the water heater which may be damaged by a leak.- If the water is not used for a long time:➤ shut off power to the appliance by setting the external switch to “OFF”;➤ close the water circuit cocks.- Water heated to over 50°C can cause immediate serious burns or even death. Children, disabled persons and the aged are particularly at risk of burns.Do not attempt to service or repair the appliance.Operation, setting the operating temperatureStart upPower up by turning the adjustment knob clockwise. The indicator lamp only remains on when heating up. The thermostat will automatically disconnect the resistance when the preset operating temperature is reached.Setting the operating temperatureOn models with external regulation, the water temperature can be set with the knob (M fig. 6) connected to the thermostat, as indicated on the device itself.USEFUL HINTSIf the water delivery is cold, have the following checked:- is there power to the thermostat and terminal block?- are the heating elements working?If the water is boiling hot (steam is coming out of the taps)Shut off electrical power to the appliance and have the following checked:- thermostat;- the amount of scale on the boiler and heating element.If the hot water delivery is insufficient, have the following checked:- the mains water pressure;- the condition of the deflector on the cold water intake pipe;- the condition of the hot water pipe;- the electrical equipment.NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF - ALWAYS HAVE THIS DONE BY A QUALIFIED TECHNICIAN.The indicated data and specifications are not binding; the manufacturer reserves the right to modify them at his own discretion notification or replacement.HYDRAULIC FITTINGS10 / EN745FAANR6TMAMFC B12 / ENAriston Thermo SpAViale Aristide Merloni 4560044 Fabriano (AN) ItalyTelefono 0732 6011 - Fax 0732 602331 ************************* Ariston Thermo South Africa (Pty) Ltd 294 Barolong St. Icon Business Park Sunderland RidgeSouth Africa(+27) 87 943 7471*************************420010753802 - 07/2020。
恒温水浴使用说明
Brookfield数字控制循环水浴操作手册Brookfield数字控制循环水浴操作手册目录Section 1 –简述1.1 拆箱1.2 内容物1.3 概述1.4 循环泵1.5 泵进口、出口连接1.6 循环回路1.7 水槽清洗1.8 环境和冷却管Section 2 –标准控制器信息2.1 前置和后置面板2.2 加热器/泵组件Section 3 –操作3.1 循环水浴放置3.2 注满水槽3.3 电源3.4 设定安全设置点3.5 选择温度单位3.6 设定上限3.7 设定设置点温度3.8 用户自定义预定温度3.9 粘贴条3.10 自动冷却操作3.11 控制器显示信息Section 4 –校正和维护4.1 校正4.2 加热器4.3 泵电机4.4 清洁4.5 水浴用水清洁4.6 冷凝器、通气孔和循环过滤器(仅针对冷/热循环水浴) Section 5 –故障排除5.1 仪器不运行（不加热、制冷或抽吸）5.2 泵不抽吸5.3 泵抽吸慢或不足5.4 不加热5.5 加热不足5.6 不制冷或制冷不足5.7 电子故障Section 6 –水浴液体Section 7 –服务和技术支持7.1 更换零件Section 8 –售后服务Section 9 –保证Section 10 –EC Declaration of ConformitySection 1 –简述1.1 拆箱水浴放置在特制的纸箱内，保留所有外包装和包装材料直到水浴装配并运行正常。
立即设置并运行水浴，以确认操作正常。
一周后，您的仪器可得到保修，但不能更换。
如果仪器被损坏或不能正常运行，联系运输公司，提出书面索赔要求，立即联系您的供货商。
将水槽中所有包装材料取出，在通电前，检查在加热器和泵周围确保没有其它东西。
本指南均适用于制冷型和水冷型循环水浴。
有关您所选的型号请参见相关指南。
1.2 内容物1.3 概述数字控制制冷/加热型和单加热型循环水浴是为独立使用水浴或通过外循环给外接设备提供精密温度控制而设计的。
EHA-1352A液体加热器（多功能养生杯）产品使用说明书
微信扫一扫 了解更多产品部件及使用说明环保清单目录010*********安全使用注意事项清洁与保养食品接触材料及制品维修服务指南10常见故障排除及处理方法09产品规格本说明书适用于EHA-1352A-G 等型号电热水壶使用产品前请仔细阅读说明书，阅读后请保管到可以随时查阅的场所，以便他人使用。
本产品仅限于中国大陆使用，不得用于电源、电压不同于中国的国家和地区。
安全使用注意事项请在使用前仔细阅读“安全注意事项”并以正确的方法使用，避免使用不当而造成损坏或危险。
本产品属I 类电器，使用前请确保插座的接地有效，同时请确认输入电压为220V~50Hz。
不要让电源线挂在桌边或接触高温物体。
不可沿尖端物或锋利边缘来拉线、压线或让它悬垂下来，同时要远离热源和湿源。
禁止放在不稳或倾斜的台面上使用本产品，避免产品倾倒引起伤害或火灾等事故。
切勿将本产品置放在热源的表面上或热源旁，如烧烤，烘炉等。
不要在地毯、塑料凳不耐热的表面或者附近使用，会因蒸气受损的物体也不12要放置在本产品上方。
注水时，请大于最小水位标志，否则水沸腾后，开关无法自动断开，也不可超过其最大水位标志，否则沸水可能喷出。
将第一次烧开的水倒掉，然后再正式使用。
因为养生壶再初次使用时，水可能有异味，如果水的异味仍未消除，加入少许苏打，再煮沸，并倒掉。
切勿将含有腐蚀性液体或糊状食物放入壶内加热。
请务必注水后再使用该产品，严禁干烧，否则可能导致产品损坏。
若产品出现干烧情况，请往壶体内加水或拔掉电源，切勿触摸发热体以防汤伤。
本产品壶身与底座必须搭配使用，不得分开使用。
操作按键时不可用力过猛，以防按键损坏。
请勿在使用时，移动产品，以免烫伤。
炖煮食材完成，壶体内还有大量蒸气，不要立刻打开上盖，断电等候几分钟再打开，避免蒸气烫伤。
使用时，请盖好壶盖，否则液体沸腾后，开关无法自动断开，且沸腾的液体可能喷出造成伤害。
在使用过程中，若发生问题时，请先将电源插头从插座上拔下，禁止湿手拔、插插头，以免触电。
飞利浦宝宝瓶盖加温器用户手册说明书
使用本产品之前，请仔细阅读本用户手册保留备用SCF356Question?有疑问? Contact Philips 请联系飞利浦ENGLISH7 -Check if the voltage indicated on the bottom of the appliance corresponds to the local mains voltage before you connect the appliance. -If you need to use an extension cord,make sure it is an earthed extension cord with a rating of at least 13 amperes.-Do not use the appliance if the plug,the mains cord or the appliance itself is damaged.If the mains cord is damaged,you must have itreplaced by Philips,a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard.-Do not place the appliance on or near a hot gas or electric cooker, or in a heated oven.-Do not preheat the appliance.-Always place a fully assembled bottle with cap in the baby bottle warmer before you add water.-Make sure you add water before you switch on the baby bottle warmer. -Hot water can cause serious burns.Be careful when the baby bottle warmer contains hot water.-The accessible surfaces of the appliance may become hot during use. -Do not move the appliance when it contains hot water.-Always check the food temperature before you feed your child.Caution-This appliance is intended to be used in household and similar applications such as farm houses,bed and breakfast type environments, staff kitchen areas in shops,offices and other working environments,and by clients in hotels,motels and other residential type environments. -Unplug the appliance when it is not in use.-Store any excess mains cord in the base to ensure stability of the baby bottle warmer.-Let the appliance cool down before you clean it.-Follow the descaling instructions to avoid irreparable damage.-Do not try to open or repair the appliance yourself.You can contact the Philips Consumer Care Centre in your country (see/support).Y ou can find the production date code YYWW in the cord storage compartment in the base of the bottle warmer.Electromagnetic fields (EMF)This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields.With this baby bottle warmer, you can safely warm and defrost milk in Philips Avent feeding bottles and milk or baby food in containers. The baby bottle warmer helps to preserve the valuable nutrients and vitamins in breast milk because it never overheats the milk. If milkbecomes too warm, nutrients and vitamins are damaged. T o help preserve the quality of your breast milk, it is important to heat the milk in a safe and controlled way. The baby bottle warmer is designed to warm gently and evenly and to avoid hot spots, as the milk circulates during warming. The built-in sensor tracks and controls the milk temperature, to avoid overheating at all times.Note: Philips Avent breast milk bags and Philips Avent 2oz/60ml bottles cannot be used in this baby bottle warmer.Explanation of settings-Y ou can choose between the following settings: (Fig. 2)-Defrost setting: T o defrost a bottle or container with frozen milk orfrozen baby food. No warming occurs.-Milk warming settings: Select one of these settings when you want towarm a bottle of milk to a safe temperature. Setting 2 warms your milk to approximately body temperature. Setting 1 warms your milk to a slightly lower temperature and setting 3 warms your milk to a slightly higher temperature.-Baby food warming setting: Select this setting when you want towarm a container or jar with baby food.Using the baby bottle warmer to warm milk 1 Put the mains plug in the wall socket (Fig. 3).2 Place a bottle centrally in the baby bottle warmer (Fig. 4).Note: To warm milk in a milk storage container, follow the same steps as indicated for warming milk in a bottle.ENGLISH8ENGLISH9 3 Fill the baby bottle warmer with the same amount of drinkingwater as the amount of milk you want to warm up (for example, to warm up 125ml/4oz of milk, you need to use 125ml/4oz of drinking water). If you want to heat up a large amount of milk (>180ml/6oz), the maximum water level is approximately 1cm/0.4 inches under the rim of the baby bottle warmer (which corresponds to adding 160ml/4.5oz of drinking water). An accurate water level ensurescorrect warming performance. (Fig. 5)4 Select the desired setting (Fig. 6).Note:Experience teaches that babies may have a preference for a specific milk temperature.This can be due to personal preference or external factors (e.g.environment temperature).All three settings ensure that the milk is warmed to a safe temperature which is comfortable for your child and helps to preserve the nutrients and vitamins in the milk.5 Press the on/off button to switch on the appliance. The light in thebutton lights up to indicate that the baby bottle warmer is on (Fig. 7). Note:The baby bottle warmer starts warming up right after you press the button.6 The progress indicator starts to fill up gradually with white light toshow the progress of the milk warming process (Fig. 8).Note:The progress indicator shows the progress of the milk warming process. The progress indicator starts flashing when the appliance is on.When the first warming phase has been completed,the bottom segment lights up continuously and the next segment starts flashing to show that the second warming phase is in progress.These steps continue until the third warming phase has been completed.Then the entire progress indicator lights up continuously.Note:During the warming process,the milk circulates to ensure even warming.It takes about 10 minutes to warm 90ml/3oz of room-temperature milk.It takes slightly longer to warm cold milk or a large amount of milk. Caution: Do not take the bottle out of the baby bottle warmer while the progress indicator is flashing.7 When the entire progress indicator lights up continuously, the milkhas reached the set temperature.,When the milk is warm, you can either take the bottle out of thebaby bottle warmer to feed your baby right away (see section ‘Feeding your baby immediately’) or you can keep it warm in the baby bottle warmer (see section ‘Keeping milk warm’).Increasing the milk temperature1 If you want the milk to be warmer, you can increase the milktemperature gradually after it is ready by switching to milk warming setting 3 and leaving the bottle in the appliance at the keep-warm mode (Fig. 9). 2 If you just switched off the baby bottle warmer or if it just switchedoff automatically, switch it back on without removing the warm water from it, and follow the above step (Fig. 10). 3 The baby bottle warmer switches off automatically after 20 minutesof keep-warm mode (Fig. 11).Feeding your baby immediately1 Press the on/off button to switch off the appliance and take out themilk bottle (Fig. 10). 2 Always check the temperature of the milk before you feed your baby.Gently swirl the milk in the bottle and check the temperature of the milk by sprinkling a few drops on the inside of your wrist (Fig. 12). 3 Unplug the appliance and empty the baby bottle warmer (Fig. 13).Keeping milk warm1 When the milk has reached the desired temperature, the babybottle warmer automatically switches to the keep-warm mode. In this mode, the milk is kept at the set temperature for 20 minutes (Fig. 14). 2 The baby bottle warmer switches off automatically after20 minutes. The progress indicator switches off to indicate that the milk is not kept at the desired temperature anymore (Fig. 11).ENGLISH10ENGLISH11 Note:If you want to feed your baby with milk at the set temperature,you need to take the milk bottle out of the baby bottle warmer and feed it to your baby right after the baby bottle warmer switches off,otherwise the milk cools down.Note:You cannot prolong the keep-warm mode of the baby bottle warmer for more than 20 minutes.Caution: It is not recommended to reheat breast milk twice, as bacteria start to develop in the milk.3 Always check the temperature of the milk before you feed yourbaby. Gently swirl the milk in the bottle or milk storage container and check the temperature of the milk by sprinkling a few drops on the inside of your wrist (Fig. 12).4 Unplug the appliance and empty the baby bottle warmer (Fig. 13).Re-using the baby bottle warmer right away foranother bottleIf you want to heat up another bottle right away,let the baby bottle warmer cool down for a few minutes.T o speed up this process,fill the baby bottle warmer with fresh cold water.When you switch on the baby bottle warmer,the progress indicator starts flashing from bottom to top to indicate that the appliance is heating up again.Note:If the progress indicator is on but does not flash,the baby bottle warmer is still too warm to heat up another bottle.Please switch off the baby bottle warmer,let it cool down for a few minutes and make sure you fill it with fresh cold water.Using the baby bottle warmer to warm baby food1 Put the mains plug in the wall socket (Fig. 3).2 Place a baby food container or jar centrally in the baby bottlewarmer (Fig. 15).Note:You can leave off the lid of the food container or jar,so you can stir the baby food during heating.3 Fill the baby bottle warmer with the same amount of drinkingwater as the amount of baby food you want to warm up (for example, to warm up 125ml/4oz of baby food, you need to use 125ml/4oz of drinking water). If you want to warm up a large amount of baby food, the maximum water level is approximately 1cm/0.4 inches under the rim of the baby bottle warmer (which corresponds to adding 160ml/4.5oz of drinking water). An accurate water level ensures correct warming performance. (Fig. 16) 4 Select the baby food warming setting (Fig. 17).5 Press the on/off button to switch on the appliance. The light in theprogress indicator shows that the baby bottle warmer is on (Fig. 18).Note: The baby bottle warmer starts warming up right after you press the button. Due to the large variety of baby food consistencies, it is not possible for the appliance to detect exactly how long the baby food should be warmed. 6 The progress indicator starts to fill gradually with white light toshow the progress of the warming process. During the warming process, do not take the jar or container out of the baby bottle warmer but stir the baby food while the jar or container is still in the baby bottle warmer (Fig. 19).Note: You can start stirring the baby food once the second segment of the progress indicator lights up continuously. Stirring before this moment is not effective as the temperature of the baby food is still too low.Caution: Do not take the food container or jar out of the baby bottle warmer during warming.7 When the entire progress indicator lights up continuously, the babyfood has reached the desired temperature.Note: Due to the large variety of baby food consistencies, it is strongly recommended that you continuously stir the baby food and check its temperature while it is heating up for an optimal result.ENGLISH12ENGLISH13 ,When the baby food is warm, you can either take the baby food container or jar out of the baby bottle warmer to feed your baby right away (see section ‘Feeding your baby immediately’) or you can keep it warm in the baby bottle warmer (see section ‘Keeping baby food warm’).Increasing the baby food temperature1 Always taste the baby food after warming it up to make sure it isnot too hot. If you want the baby food to be warmer, put thecontainer back into the baby bottle warmer and leave it in there at the keep warm-mode for some time. Keep stirring the babyfood (Fig. 15).2 If you just switched off the baby bottle warmer or if it just switchedoff automatically, switch it back on without removing the warmwater from it, and follow the above step (Fig. 18).3 The baby bottle warmer switches off automatically after 20 minutesof keep-warm mode (Fig. 20).Feeding your baby immediately1 Press the on/off button to switch off the appliance and take out thebaby food container or jar (Fig. 18).2 After warming,taste the baby food to ensure it is not too hot (Fig.21).3 Unplug the appliance and empty the baby bottle warmer (Fig. 13).Keeping baby food warm1 When the baby food has reached the desired temperature, thebaby bottle warmer automatically switches to the keep-warmmode. In this mode, the baby food is kept at the desiredtemperature for 20 minutes (Fig. 22).2 The baby bottle warmer switches off automatically after20 minutes. The progress indicator switches off to indicate that thebaby food is not kept at the desired temperature anymore (Fig. 20).Note: If you want to feed your baby with the baby food at the settemperature, you need to take the baby food out of the baby bottle warmer and feed it to your baby right after the baby bottle warmer switches off. If you do not do this, the baby food slowly cools down.Note: You cannot prolong the keep-warm mode of the baby bottle warmer for more than 20 minutes. 3 Always check the temperature of the baby food before you feed your baby. Gently stir the baby food in the baby food container or jar and taste the baby food to ensure it is not too hot (Fig. 21). 4 Unplug the appliance and empty the baby bottle warmer (Fig. 13).Re-using the baby bottle warmer right away for another container of baby foodIf you want to heat up another container or jar with baby food right away, let the baby bottle warmer cool down for a few minutes. T o speed up this process, fill the baby bottle warmer with fresh cold water. When you switch on the baby bottle warmer, the progress indicator starts flashing from bottom to top to indicate that the appliance is heating up again.Note: If the progress indicator is on but does not flash, the baby bottle warmer is still too warm to heat up another container or jar with baby food. Please switch off the baby bottle warmer, let it cool down for a few minutesand make sure you fill it with fresh cold water.Defrost settingAt this setting, you can defrost frozen milk or baby food. Follow the steps indicated in sections ‘Using the baby bottle warmer to warm milk’or ‘Using the baby bottle warmer to warm baby food’.The progress indicator starts flashing when the appliance is on the defrost setting. The progress indicator gradually fills with white light to show the progress of the defrosting process. The milk or baby food has defrosted completely when the entire progress indicator lights up continuously.The defrost setting defrosts the milk or baby food but does not warm it up. If you want to warm up milk or baby food after defrosting it, first switch off the appliance, then select the desired warming setting andswitch the appliance back on.ENGLISH14ENGLISH15 Cleaning1 After each use, unplug the baby bottle warmer and let it cooldown (Fig. 23).2 Remove the water from the baby bottle warmer for hygienicreasons (Fig. 24).3 Wipe the outside and inside of the baby bottle warmer with amoist cloth (Fig. 25).Do not use abrasive, anti-bacterial cleaning agents, chemical solvents or sharp tools to clean the baby bottle warmer.Note:If you used the baby bottle warmer to warm containers with baby food, make sure that no spilled baby food remains on the bottom of the baby bottle warmer.DescalingIt is recommended to descale the baby bottle warmer everyfour weeks to ensure it continues to work efficiently.1 Mix 50ml/1.7oz of white vinegar with 100ml/3.4oz of cold water todescale the baby bottle warmer. First select the defrost setting,then switch on the baby bottle warmer and let the applianceoperate for 10 minutes. Leave the solution in the baby bottlewarmer until all scale has dissolved (Fig. 26).Note:You can also use citric acid based descalers.Note:Do not use other types of descalers.2 Unplug the baby bottle warmer before you empty it (Fig. 23).3 Empty the baby bottle warmer and rinse its inside thoroughly. If youstill see traces of scale after rinsing, repeat the descalingprocedure (Fig. 24).Do not throw away the product with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment.If you need information or support, please visit/support or read the separate worldwide guaranteeleaflet.ENGLISH1618 -如果您需要延長線，請務必使用有接地，且安培數至少為 13 的延長線。
电子 暖水底板加热器（型号D）说明书
Dear Owner,Congratulations! Thank you for purchasing this new heater manufactured by Marley Engineered Products. You have made a wise investment selecting the highest quality product in the heating industry.Please carefully read and follow the installation and maintenance directions shown in this manual. You should enjoy years of efficient heating comfort with this product from Marley Engineered Products... the industry’s leader in design, manufacturing, quality and service.... The Employees ofMarley Engineered Productsfaces are suggested:a.Plaster Walls:Use toggle or molly screw anchors.b.Wall Studs:Use #12 round head screws penetrating at least 3/4" (19mm)into stud.c.Masonry Walls:Use #12 round head screws into lead, plastic, or fiberexpansion anchor.Tighten all screws snugly, then back off 1/2-turn to allow the back panel to expand and contract.10.Connect supply wiring to heater as described in Figure 6, or as shown in thewiring diagrams supplied with the accessory kits intended for use with this heater.11.Secure the desired accessories to baseboard as shown in the accessoryinstruction sheet, and use the wiring diagram supplied with the accessory.NOTE: Baseboard heaters must be thermostatically controlled.12.Replace the front cover by fitting the top lip of the cover onto the tabs on eachjunction box and top edge of the element support bracket(s). Rotate the cover downward, pushing the bottom corners inward. Install two screws (removed in Step 4) through the cover into the junction boxes. See that the bottom of the cover is engaged onto the bottom of each element support bracket. See 13.Replace the end cap(s) by installing screw(s) (removed in Step 3).INSTALLATION OF MULTIPLE UNITS1.With heaters mounted end-to-end, allow 1/32-inch (1mm) of expansion spaceper heater between each heater.2.For each heater to be installed, refer to and follow “Installation of Single Unit”,Steps 1 through 8.3.If the power supply is to enter through the end of the heater series so that theend cap can be installed after the heaters are installed, continue “Installation of Single Unit”, Steps 9 through 12.4.I f the power supply is to feed heaters at the junction box that is adjacent toanother heater, it is easier for the power supply connections to be made prior to the installation of the heater(s) to the wall. If this is not possible, connections may be made through the opening in the junction boxes when the front cover(s)5.Connecting power supply cables may be routed from heater to heater by drillinga 1/2-inch (13mm) diameter hole in the end caps for the heaters that fit togeth-er. See Figure 9. To prevent possible damage to internal heater wiring, all6.Wire heaters as shown in Wiring Diagram, Figure 10.7.Replace the front covers and end caps according to “Installation of Single Unit”,OPERATING AND MAINTENANCE INSTRUCTIONS1.An integral or remote wall thermostat is recommended for each room. In verylarge rooms it is recommended that a low voltage thermostat with double or multiple circuit relays be used to provide the most comfortable results.DO LOCATE DO NOTTHERMOSTAT LOCATE THERMOSTAT•A minimum of two feet• Near televisions or(61cm) from any appliances that emit heat.outside wall.•Near drafts from an•Approximately five feet open doorway.(1,5m) from the floor,•Where it would be struckpreferably on an inside by direct rays of sunlight.wall location.2.After the baseboard system has been completely installed, all thermostatsshould be turned to LOW or NO HEAT setting. Then turn on breakers or install fuses. Wait 3 to 5 minutes and check to see that none of the heaters are oper-ating. If operating, disconnect power and check wiring. If none are operating then turn the thermostats to highest setting and wait 3 to 5 minutes. Check to see that all heaters are operating. Should any not be operating, disconnect power and check wiring.3.Allow entire system to operate steadily for 1/2-hour. For a period of time afterthe heaters are put into operation, the owner may notice a “new smell” coming from the heaters. This is expected on new installations. Bringing heaters to full operation will eliminate this condition in a short period of time.4.Select the setting for comfort on all thermostats.5.To clean heater:Because of the convection heating principle which dependsupon circulation of air through the finned element, dust particles will periodical-ly be deposited between the fins and should be removed occasionally for max-imum efficiency of the heater. A vacuum cleaner with proper attachments can easily be worked along the top and bottom of the finned element to clear it of dust deposits.NOTE: The painted finish of the heater may be cleaned with a slightly damp cloth if desired. Do not use wax cleaners or polishes as these waxes may vaporize when the heater is in operation and cause discoloration.ECR 369745200-2083-00511/06HOW TO OBTAIN WARRANTY SERVICE ANDWARRANTY PARTS PLUS GENERAL INFORMATION1. Warranty Service or Parts1-800-642-43282. Purchase Replacement Parts1-800-654-35453. General Product Information Note:When obtaining service always have the following:1. Model number of the product2. Date of manufacture3. Part number or description。