辰阳说明书1(1)
Trigonox 301产品说明书
产品数据表Trigonox 3013,6,9-Triethyl-3,6,9-trimethyl-1,4,7-triperoxonane在挤出工艺中，Trigonox® 301是生产可控流变聚丙烯（CR-PP）的有效过氧化物。
CAS 编号24748-23-0EINECS/ELINCS编号429-320-2TSCA 状态清单上列出的分子量264.3活性氧含量过氧化物18.16%规格活性氧7.3-7.6 %色度50 Pt-Co/APHA max.特性外观, 20-25 °C清澈至微混浊的液体密度, 20 °C0.875 g/cm³粘度, 20 °C 5 mPa.s应用Trigonox® 301 可用于细分市场：聚合物生产和丙烯酸树脂生产，具有不同的应用/功能。
如需更多信息，请查看我们的网站和/或联系我们。
半衰期数据有机过氧化物的活性通常以其在不同温度下的半衰期(t1/2)表示。
Trigonox® 301 在氯苯中的半衰期为：0.1 小时170°C (338°F)1 小时146°C (295°F)10 小时125°C (257°F)公式 1kd = A·e-Ea/RT公式 2t½ = (ln2)/kdEa150.23 kJ/moleA 1.02E+15 s-1R8.3142 J/mole·KT(273.15+°C) K热稳定性有机过氧化物是热不稳定物质，可发生自加速分解。
自加速分解温度（SADT）是一种物质在其用于运输的包装中可能产生自加速分解的最低温度。
SADT根据热积累储存试验测定。
SADT110°C (230°F)方法热累积储存试验是公认的用于测定有机过氧化物SADT的测试方法（见《关于危险货物运输的建议书·试验和标准手册》– 联合国，纽约和日内瓦）。
sevencompact的说明书
sevencompact的说明书
产品介绍
1、测量快速、精确
2、友好的操作界面
3、包括中文的10种菜单语言
4、清晰直观的彩色显示屏
5、可连接多种外围设备
6、符合GLP规范
7、全面的服务(包括IQ/OQ认证)
8 、 uPlace电极支架：单手就能方便操作，可完全垂直上下移动，避免样品容器的翻倒和电极的损坏。
9、自动校正，自动识别缓冲液
10、电极状态及斜率显示，随时监测电极状态
11、自动终点锁定功能，消除人为读数误差
12、关机后能长时间保持校正数据，对于不同样品可选择最佳的终点方式
13、有自动和手动两种温度补偿方式，补偿温度范围均在-30至130℃间
14、灵活的数据处理：通过RS232接口和USB接口连接电脑和打印机，可将数据存储在仪表中、打印、传输至电脑。
15、独特的仪表自检功能帮助判断测量出错原因
技术参数
S210-K 配置：1、S210 主机
2、电极Inlab Expert Pro
3、电极支架
4、袋装缓冲溶液pH 4.01 7.00 9.21
5、保护罩
6、电源
7、使用说明书
8、保修卡
9、校验证书
备注：电极可根据实际应用情况进行选择。
12 taiyo yuden 产品使用注意事项说明书
Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products.■ Product information in this catalog is as of October 2011. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-fore practical application or usage of the Products.Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorpo-rating such products, which are caused under the conditions other than those specified in this catalog or individual specification.■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available.■ Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment.■ All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-rine system, military, etc. where higher safety and reliability are especially required.In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage.■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-tors (so called “TAIYO YUDEN’s official sales channel”).It is only applicable to the products purchased from any of TAIYO YUDEN’ s official sales channel.■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may oc-cur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.■ Caution for exportCertain items in this catalog may require specific procedures for export according to “Foreign Exchange and For-eign Trade Control Law”of Japan, “U.S. Export Administration Regulations”, and other applicable regulations.Should you have any question or inquiry on this matter, please contact our sales staff.notice_e-0176mlci03_e-01■ FEATURES■ ORDERING CODE■ EXTERNAL DIMENSIONS/STANDARD QUANTITY■ APPLICATIONS■ AVAILABLE INDUCTANCE RANGE＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (/) or CD catalogs.◦ L ow profile below 1.2mm.◦ L ow Rdc.◦ M ultilayer block Structure yields higher reliability.◦ N ew line up NM series improved in inductance temperature character-istic based on current CK series P type.◦ D C/DC converter for the Mobile equipment; Cellular Phones,DSC, DVC.MULTILAYER CHIP POWER INDUCTORS (CK SERIES P TYPE / NM SERIES )C KP 2520V1R0M －T ○REFLOW77mlci03_e-01INDUCTORSPOWER INDUCTORS■ PART NUMBERS＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (/) or CD catalogs. ●CKP2012●CKP2016●CKP2520●NM2012●NM252078mlci03_e-01■ ELECTRICAL CHARACTERISTICS ＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (/) or CD catalogs.INDUCTORSPOWER INDUCTORS＊This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (/) or CD catalogs.79mlci03_e-01mlci0109_reli-PRP1mlci0109_reli_e-01＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (/) or CD catalogs.◦Tape & Reel Packaging①Minimum Quantity ②Taping material◦Paper tape (0.315 inches wide)③Taping Dimensions（inch ）To next page C K 2125C K S 2125C K P 2012C K P 2016C K P 2520N M 2012N M 2520L K 2125H K 2125B K 2125B K3216C K1608C K 2125C K S 2125L K 1005L K 1608L K 2125H K 0402H K 0603H K 1005H K 1608H K Q 0603A Q 105B K 0402B K 0603B K 1005B K 1608B K 2125B K 2010B K P 0603B K P 1005B K P 1608B K P 2125B K H 1005mlci0109_reli-PRP2mlci0109_reli_e-01＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (/) or CD catalogs. （inch ）◦Embossed Tape (0.315 inches wide)④LEADER AND BLANK PORTIONDirection of tape feed15.7inches or more⑤Reel Size⑥Top tape strengthThe top tape requires a peel-off force of 0.1～0.7N in the direction of the arrow asillustrated below.mlci0109_reli-PRP3mlci0109_reli_e-01＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (/) or CD catalogs.mlci0109_reli-PRP4mlci0109_reli_e-01＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (/) or CD catalogs. Definition of rated current ：・In the CK, CKS and BK Series, the rated current is the value of current at which the temperature of the element is increased within 20℃.・In the BK Series P type and CK Series P type, NM Series the rated current is the value of current at which the temperature of the element is increased within 40℃.・In the LK,HK,HKQ,and AQ Series, the rated current is either the DC value at which the internal L value is decreased within 5% with the application of DC bias, or the value of current at which the temperature of the element is increased within 20℃.BK0402 SeriesMeasuring frequency ：100±1MHz Measuring equipment ：E4991A （or its equivalent ）Measuring jig ：16196D （or its equivalent ）BK0603 Series, BKP0603 Series Measuring frequency ：100±1MHz Measuring equipment ：4291A （or its equivalent ）Measuring jig ：16193A （or its equivalent ）BK1005 Series, BKP1005 Series, BKH1005 Series Measuring frequency ：100±1MHz Measuring equipment ：4291A （or its equivalent ）Measuring jig ：16192A （or its equivalent ）, 16193A （or its equivalent ）BK1608・2125 Series, BKP1608・2125 SeriesMeasuring frequency ：100±1MHz Measuring equipment ：4291A （or its equivalent ）, 4195A （or its equivalent ）Measuring jig ：16092A （or its equivalent ） or 16192A （or its equivalent ）/HW BK2010・3216 SeriesMeasuring frequency ：100±1MHz Measuring equipment ：4291A （or its equivalent ） , 4195A （or its equivalent ） Measuring jig ：16192A （or its equivalent ）mlci0109_reli-PRP5mlci0109_reli_e-01＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (/) or CD catalogs.CK Series ：Measuring frequency ：2 to 4MHz （CK1608）Measuring frequency ：2 to 25MHz （CK2125）Measuring frequency ：2 to 10MHz （CKS2125）LK Series ：Measuring frequency ：10 to 25MHz （LK1005） Measuring frequency ：1 to 50MHz （LK1608） Measuring frequency ：0.4 to 50MHz （LK2125）CKP Series, NM Series ：Measuring frequency ：1MHz （CKP2012, CKP2016, CKP2520, NM2012・NM2520）Measuring equipment, jig ：・4194A ＋16085B ＋16092A （or its equivalent ）・4195A ＋41951＋16092A （or its equivalent ）・4294A ＋16192A （or its equivalent ）・4291A ＋16193A （or its equivalent ）/LK1005・4285A ＋42841A ＋42842C ＋42851－61100（CKP2012・CKP2016・CKP2520・NM2012・NM2520）Measuring current ：・1mA rms （0.047 to 4.7μH ） ・0.1mA rms （5.6 to 33μH ）HK 、HKQ 、AQ Series ：Measuring frequency ：100MHz （HK0402・HK0603・HK1005・AQ105）Measuring frequency ：50/100MHz （HK1608・HK2125）Measuring frequency ：500MHz （HKQ0603S ・HKQ0603U ）Measuring equipment, jig ：・4291A ＋16197A （or its equivalent ）/HK0603・AQ105・4291A ＋16193A （or its equivalent ）/HK1005 ・E4991A ＋16197A （or its equivalent ）/HKQ0603S ・HKQ0603U ・4291A ＋16092＋in-house made jig （or its equivalent ）/HK1608・HK2125・E4991A ＋16196D （or its equivalent ）/HK0402Measuring equipment ：VOAC-7412（made by Iwasaki Tsushinki ） VOAC-7512（made by Iwasaki Tsushinki ）CK Series ：Measuring frequency ：2 to 4MHz （CK1608）Measuring frequency ：2 to 25MHz （CK2125）LK Series ：Measuring frequency ：10 to 25MHz （LK1005）Measuring frequency ：1 to 50MHz （LK1608）Measuring frequency ：0.4 to 50MHz （LK2125）Measuring equipment, jig ：・4194A ＋16085B ＋16092A （or its equivalent ）・4195A ＋41951＋16092A （or its equivalent ）・4294A ＋16192A （or its equivalent ）・4291A ＋16193A （or its equivalent ）/LK1005Measuring current ：・1mA rms （0.047 to 4.7μH ） ・0.1mA rms （5.6 to 33μH ）HK 、HKQ 、AQ Series ：Measuring frequency ：100MHz （HK0603・HK1005・AQ105）Measuring frequency ：50/100MHz （HK1608・HK2125）Measuring frequency ：500MHz （HKQ0603S ・HKQ0603U ）Measuring equipment, jig ： ・4291A ＋16197A （or its equivalent ）/HK0603・AQ105・4291A ＋16193A （or its equivalent ）/HK1005・E4991A ＋16197A （or its equivalent ）/HKQ0603S ・HKQ0603U ・4291A ＋16092A ＋ in-house made jig （or its equivalent ）/HK1608・HK2125・E4991A ＋16196D （or its equivalent ）HK0402LK Series：Measuring equipment：4195A（or its equivalent）Measuring jig：41951＋16092A（or its equivalent）HK、HKQ、AQ Series：Measuring equipment：8719C（or its equivalent）・8753D（or its equivalent）/HK2125Reference temperature：＋20℃Testing board：glass epoxy-resin substrate0.8mmThickness：Solder temperature：230±5℃Duration：4±1 sec.Solder temperature：260±5℃Duration：10±0.5 sec.Preheating temperature：150 to 180℃Preheating time：3 min.Flux：Immersion into methanol solution with colophony for 3 to 5 sec.Recovery：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1）Step 1：Minimum operating temperature＋0－3℃ 30±3 min.Step 2：Room temperature 2 to 3 min.Step 3：Maximum operating temperature＋3－0℃ 30±3 min.Step 4：Room temperature 2 to 3 min.Number of cycles：5Recovery：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1）(Note 1) When there are questions concerning mesurement result；measurement shall be made after 48±2 hrs of recovery under the standard condition.BK, BKP, BKH Series：Temperature：40±2℃Humidity：90 to 95％RHDuration：500＋24－0hrsRecovery：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1）LK、CK、CKS、CKP、NM、HK、HKQ、AQ Series：Temperature：40±2℃（LK、CK、CKS、CKP、NM Series）：60±2℃（HK、HKQ、AQ Series）Humidity：90 to 95％RHDuration：500±12 hrsRecovery：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1）BK, BKP, BKH Series：Temperature：40±2℃Humidity：90 to 95％RHApplied current：Rated currentDuration：500＋24－0hrsRecovery：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1）LK、CK、CKS、CKP、NM、HK、HKQ、AQ Series：Temperature：40±2℃（LK、CK、CKS、CKP、NM Series）：60±2℃（HK、HKQ、AQ Series）Humidity：90 to 95％RHApplied current：Rated currentDuration：500±12 hrsRecovery：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1）Note on standard condition: "standard condition" referred to herein is defined as follows:5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure.When there are questions concerning measurement results:In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition."(Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition.BK, BKH Series：Temperature：125±3℃Applied current：Rated currentDuration：500＋24－0hrsRecovery：2 to 3 hrs of recovery under the standard condition after the removal from test chamber.（See Note 1）LK、CK、CKS、CKP、NM、HK、HKQ、AQ、BKP Series：Temperature：85±2℃（LK、CK、CKS、CKP、NM、BKP Series）：85±2℃（HK1608，2125）：85±2℃（HK1005, AQ105 operating temperature range －55 to ＋85℃）：125±2℃（HK0402, HK0603, HK1005, HKQ0603S, HKQ0603U, AQ105 operating temperature range －55 to ＋125℃）Applied current：Rated currentDuration：500±12 hrsRecovery：2 to 3 hrs of recovery under the standard condition after the test.（See Note 1）Note on standard condition: "standard condition" referred to herein is defined as follows:5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure.When there are questions concerning measurement results:In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless other-wise specified, all the tests are conducted under the "standard condition."(Note 1) Measurement shall be made after 48±2 hrs of recovery under the standard condition.To next pagemlci0109_reli-PRP16mlci0109_reli_e-01■ PRECAUTIONS＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (/) or CD catalogs.Precautions on the use of Multilayer chip Inductors, Multilayer chip inductors for high frequency, Multilayer chip bead Inductors。
宁波池洋测氧测爆操作说明书
宁波池洋测氧测爆操作说明书宁波池洋测氧测爆操作说明书一、产品概述宁波池洋测氧测爆设备是一种用于测量水体中溶解氧浓度以及判断是否存在可燃气体的仪器。
该设备具有安全可靠、操作简便、测量准确等特点，广泛应用于水质监测、环境保护、污水处理等领域。
二、安全注意事项1. 在操作前请认真阅读本操作说明书，并按照说明进行操作。
2. 室内操作时请确保通风良好，避免氧气浓度过高引发安全事故。
3. 请确保设备连接正常，电源接地可靠，以防止电气泄露引发触电事故。
4. 长时间使用设备时，请注意设备的散热，避免设备过热。
5. 使用结束后，请将设备断电并拔掉电源插头，以确保安全。
三、操作步骤1. 将设备放置在稳定平整的工作台上，确保设备稳固。
2. 连接电源，将电源插头插入电源插座，并打开电源开关。
3. 设备启动后，待显示屏上显示正常后，即可进行测量操作。
4. 进行测氧操作时，将测氧头部分浸入水体中，确保电极与水完全接触。
5. 测氧过程中，注意不要过度摇动测氧设备，以防止测量结果出现误差。
6. 测量完成后，将测氧设备从水中拿出，并将设备断电。
四、注意事项1. 请注意设备与水体的接触部分是否存在损坏或磨损，如有损坏请及时更换。
2. 测量过程中，如发现异常，请立即停止使用并联系维修人员。
3. 使用过程中，请注意保持设备清洁干燥，避免灰尘或水分进入设备内部，影响测量准确性。
4. 长时间不使用设备时，请将设备存放在干燥通风的地方，避免受潮或损坏。
以上就是宁波池洋测氧测爆操作说明书的全部内容，请根据说明进行正确的操作和使用。
如有其他问题，请及时联系我们的售后客服。
超晨犇脉冲充电器说明书
超晨犇脉冲充电器说明书超晨犇脉冲充电器说明书第一章：产品介绍1.1 产品概述超晨犇脉冲充电器是一种用于充电电池的装置，采用高频脉冲充电技术，具有快速充电、高效能、安全、节能、环保等特点。
1.2 产品结构超晨犇脉冲充电器主要由以下几个部分构成：（1）主机：负责控制充电器的工作状态和充电电流的输出。
（2）输入电源接口：用于连接电源插座，将电源输入充电器。
（3）输出电源接口：用于连接待充电设备的电池。
（4）显示屏：显示充电状态、电池容量百分比、工作模式等信息。
（5）控制按钮：用于调节充电模式、启动/停止充电等操作。
第二章：产品使用注意事项2.1 安全警告（1）请遵守使用说明，确保充电器在正确及安全的环境下使用。
（2）请避免在高温、潮湿或有害气体的环境中使用充电器。
（3）使用过程中请不要将手指或其他金属物体插入充电器的输入/输出接口。
（4）请勿在充电器上堆积过多物品，以免影响散热效果或故障。
2.2 充电过程中的注意事项（1）请使用原装电池或符合规定的电池进行充电，以免发生安全事故。
（2）请在充电过程中密切注意电池的温度，如发现异常情况请停止充电并检查电池。
（3）请避免将充电器暴露在阳光直射下或高温环境中，以免影响充电器的散热效果。
第三章：主要功能与使用方法3.1 充电模式选择超晨犇脉冲充电器具有多种充电模式供用户选择。
用户可以根据电池类型、电池容量、充电时间等需求选择合适的充电模式。
3.2 充电电流调节超晨犇脉冲充电器支持充电电流的调节，用户可以根据需要选择合适的充电电流。
一般情况下，电池的充电电流应该根据其容量的比例进行设置。
3.3 充电状态显示超晨犇脉冲充电器的显示屏会实时显示充电状态、电池容量百分比、工作模式等信息，方便用户随时了解充电进度。
3.4 快速充电功能超晨犇脉冲充电器采用高频脉冲充电技术，具有快速充电的功能。
在合适的充电模式和充电电流下，充电器能够快速而稳定地对电池进行充电。
第四章：常见问题及解决方法4.1 充电过程中出现温度过高的情况怎么办？如果在充电过程中发现电池温度过高，请停止充电并等待电池冷却。
STYKER MD Series 产品说明书
ENGLISH (EN)IntroductionThis Instructions For Use manual is the most comprehensive source of information for the safe and effective use of your product. This manual may be used by in-service trainers, physicians, nurses, surgical technologists, biomedical equipment technicians, and central supply/sterile processing technicians. Keep and consult this reference manual during the life of the product.The following conventions are used in this manual:• A WARNING highlights a safety-related issue. ALWAYS comply with this information to prevent patient and/or healthcare staff injury.• A CAUTION highlights a product reliability issue. ALWAYS comply with this information to prevent product damage.• A NOTE supplements and/or clarifies procedural information. For additional information, especially safety information, or in-service training, contact your Stryker sales representative or call Stryker customer service. Outside the US, contact your nearest Stryker subsidiary.NOTE: The user and/or patient should report any serious product-related incident to both the manufacturer and the Competent Authority of the European Member State where the user and/or patient is established.Indications For UseSee the instructions for use supplied with the handpiece. ContraindicationsSee the instructions for use supplied with the handpiece.For Use WithThe MD Series Attachments are intended for use with the following Stryker handpieces:DESCRIPTION REFRemB® Electric Micro Drill6400-015-000 Consolidated Operating Room Equipment5400-015-000 (CORE™) Micro DrillTotal Performance System (TPS™) Micro Drill5100-015-000User/Patient SafetyWARNINGS:• Only trained and experienced healthcare professionals should use this equipment.• Before using any system component or any component compatible with this system, read and understand theinstructions. Pay particular attention to WARNING information.Become familiar with system components prior to use.• Upon initial receipt and before each use, clean and sterilize the equipment as indicated. See the care instructions manual supplied with the handpiece.• Upon initial receipt and before each use, operate the equipment and inspect each component for damage. DO NOT use anyequipment if damage is apparent or the inspection criteria are not met. See the care instructions manual supplied with thehandpiece for inspection criteria.• When operating the handpiece, DO NOT actuate the attachment collar. Actuation may suddenly stop and/or overheat thehandpiece.• DO NOT attempt to insert or remove any cutting accessory or attachment while the handpiece is operating.• DO NOT apply excessive pressure. Monitor heavy sideloads and/or long operating periods to prevent overheating of thedistal tip and body of the handpiece and/or attachment.Excessive pressure may bend or fracture the cutting accessory.• ALWAYS operate the equipment within the specified environmental condition values. See the Specifications section. • ALWAYS follow the recommended duty cycle to prevent the equipment from overheating. See the Specifications section. • Use adequate irrigation during cutting to prevent heat generation.• When in use, attachments are applied parts. See the instructions for use supplied with the handpiece for information specific to applied parts.AccessoriesWARNINGS:• Use only Stryker-approved system components and accessories unless otherwise specified.• DO NOT modify any system component or accessory unless otherwise specified.NOTES:• A variety of specialized attachments are available for use with the Micro Drill. Each specialized attachment is supplied withspecific instructions.• For a complete list of accessories, contact your Stryker sales representative or call Stryker customer service. Outside the US, contact your nearest Stryker subsidiary.The following Stryker-approved accessories are sold separately: DESCRIPTION REFE-Type Attachment Bur Guard5100-015-301 Cutting AccessoriesWARNINGS:• Upon initial receipt and before use, visually inspect the package for damage to confirm the integrity of the sterile barrier. Donot use the product if damage is apparent, the sterile barrier is compromised, or the package is unintentionally opened.• All cutting accessories are intended for single use only. Reuse significantly increases wear on the handpiece and attachment. • DO NOT reuse, reprocess, or repackage a single use device.A single use device is intended for a single use only. A singleuse device may not withstand chemical, chemical vapor, orhigh temperature sterilization reprocessing. Design featuresmay make cleaning difficult. Reuse may create a serious risk of contamination and may compromise the structural integrity of the single use device resulting in operational failure. Critical product information may be lost if the single use device isrepackaged. Failure to comply may lead to infection or cross-infection and result in patient and/or healthcare staff injury.• DO NOT use a cutting accessory with an overall length greater than 2.25 inches [5.72 cm] with the Micro Drill attachmentsdescribed in this instruction booklet.NOTE: Sterile cutting accessories are sterilized by irradiation. DESCRIPTION REF5.0 mm Egg Bur0277-010-0503.0 mm Matchhead Bur, Extended0277-010-208 Carbide Burs0277-010-2210277-010-2350277-010-4215300-010-4215300-010-50X series5300-010-51X series5300-010-70X series5300-010-71X series5300-010-90X series 6.1 mm Pear Bur1608-002-005Metal Cutting Diamond Disc1608-006-099S4Toe Fusion Sets1608-010-100SX series Resurfacing Tools1900-010-0401900-015-0401900-015-025Drill Bits, Medium5300-010-0415300-010-0595300-010-0635300-010-071 Swanson Pilot Point Burs, Medium5300-010-13X series Round Diamond Burs, Medium5300-010-3035300-010-3075300-010-311 Dermabraders5300-010-9115300-010-94X seriesIf the following symbol is on the device label, the device meets the stated criteria:DefinitionsThe symbols located on the equipment and/or labeling are defined in this section or in the Symbol Definition Chart. See the Symbol Definition Chart supplied with the equipment.InstructionsNOTE: The Micro Drill handpiece may be operated with the Stryker footswitch or handswitch.AssemblyWARNING: Ensure the handpiece is off. DO NOTattach any cutting accessory or attachment while thehandpiece is running.1. Install the attachment onto the handpiece with a twisting motionuntil it securely snaps into place. See figure 1.Figure 1. Attachment InstallationNOTE: Ensure the attachment is secure before running the Micro Drill. Observe the small gap between the attachment and the Micro Drill housing caused by the anti-rotation pin. This gap will not hinder the function of the Micro Drill or the attachment. The gap should not be wider than 0.025 inches [0.65 mm].Assembly (continued)2. Insert the cutting accessory as follows:2. 1. Rotate the lock collar to the LOAD position. See figure 2.2. 2. Insert the cutting accessory into the attachment with atwisting motion until it bottoms.Figure 2. Cutting Accessory Installation2. 3. Rotate the lock collar to the RUN position. See figure 3.Figure 3. Cutting Accessory Locked Into Place2. 4. Gently tug on the cutting accessory to ensure that it islocked into place.WARNING: Ensure the cutting accessory is correctlyinstalled. A burn injury may result if the accessory isincorrectly installed and friction occurs between theaccessory and the attachment.Disassembly1. Rotate the lock collar to the LOAD position. See figure 4.2.Pull the cutting accessory straight out of the handpiece.Figure 4. Cutting Accessory Removal3. Grasp the attachment and pull it away from the handpiece. Care InstructionsFor processing instructions and disposal/recycle information, see the care instructions manual supplied with the handpiece. TroubleshootingWARNING: DO NOT disassemble or service thisequipment, unless otherwise specified.NOTE: For service, contact your Stryker sales representative or call Stryker customer service. Outside the US, contact your nearest Stryker subsidiary.PROBLEM CAUSE SOLUTIONAttachment is difficult to install or remove from the handpiece. The connectorrequires a break-inperiod.Install and removethe attachmentrepeatedly until theconnector functionssmoothly.Attachment will not retain the cutting accessory.Lock collar is notfully engaged.Rotate the collar tothe LOAD position.Reinstall the cuttingaccessory. Fullyrotate the collar tothe RUN position.Gently tug on thecutting accessory toensure it is secure.PROBLEM CAUSE SOLUTIONHandpiece will not run.Lock collar is notfully engaged.Fully rotate thecollar to the RUNposition.Cutting accessory will not disengage from the attachment.Lock collar is notfully disengaged.Fully rotate thecollar to the LOADposition.Cutting accessory seizes in the attachment.Lock collar is notfully engaged.Rotate the collar tothe LOAD position.Reinstall the cuttingaccessory. Fullyrotate the collarclockwise to theRUN position.Gently tug on thecutting accessory toensure it is secure. Attachment is notproperly installedinto the handpiece.Reinstall theattachment. Ensurethe connectionis flush to thehandpiece.Attachment runs at a gradually higher temperature over its operating life.Attachment isbeginning to wear.Return theattachmentto Stryker forevaluationand possiblereplacement.Attachment heats up rapidly during use.Debris is trappedinside theattachment.Clean and sterilizethe attachment.Internal componentsof the attachmentare damaged.Return theattachmentto Stryker forevaluationand possiblereplacement.Attachment contains moisture and leaks fluid during use.Attachment wasimproperly cleanedand sterilized.Clean and sterilizethe attachment.Comply with DryCycle requirements.SpecificationsWARNING: ALWAYS check any documentation thataccompanies attachments and/or cutting accessoriesfor special duty cycle and usage instructions. Model:MD Series Straight Attachment(REF 5100-015-250)Dimensions: 3.4 inch [87.2 mm] length0.8 inch [19.6 mm] diameterMass:0.15 lb [69.3 g]Model:MD Series Angled Attachment(REF 5100-015-252)Dimensions: 5.2 inch [130.9 mm] length0.8 inch [19.6 mm] diameterMass:0.26 lb [117.0 g]Model:MD Series Long Straight Attachment(REF 5100-015-270)Dimensions: 4.3 inch [109.0 mm] length0.8 inch [19.6 mm] diameterMass:0.18 lb [80.3 g]Model:MD Series Long Angled Attachment(REF 5100-015-272)Dimensions: 6.0 inch [153.5 mm] length0.8 inch [19.7 mm] diameterMass:0.28 lb [127.7 g]Equipment Type:See the instructions for use suppliedwith the handpiece.Mode of Operation:Non-continuous OperationDuty Cycle:20 seconds on/20 seconds off, 10 times Rest Between Cycles:30 minutesApplied Part:When used with handpieces, theattachments described in this manualare applied parts. For more information,see the instructions for use suppliedwith the handpiece.5100-015-735 Rev-AB EN Specifications (continued)Maximum Temperature of Applied Part:Less than 124 °F [51 °C] (Maximum surface temperature as tested to the standards listed under Product Safety Certification in the instructions for use supplied with the console.)EnvironmentalConditions:OperationStorage and TransportationTemperatureLimitation: Humidity Limitation:AtmosphericPressure Limitation:Stryker Instruments1941 Stryker WayPortage, Michigan(USA) 490021-269-323-77001-800-253-3210ES/DE/FR/IT/NLJA/ZH/KOSV/DA/FI/PT/NOPL/EL 5100-015-718 5100-015-722 5100-015-731 5100-015-750。
Amphenol 系列产品说明书
Slide Lock Post for High Volume ApplicationsOrder 2 per connectorTool required for installation. See this page.Materials and FinishesMaterial:Stainless Steel Treatment:PassivatedNOTE: Not suitable for rear panel mountingTool for High Volume ApplicationsPart Number:D53018Materials and FinishesMaterial:SteelFinish:Yellow Chromate over Cadmium or ZincNOTE: When rear-mounting connector to a 1/16⍯panel, delete the 2 washers.Part Number:980-2000-860Panel Thickness:1,09-0,91 (.043-.036)Part Number:995-2000-092#4-40NUT, HEXSpring Latch Plate Assembly#4-40Shell Size Layout Part Number A ±0,38 (.015)B ±0,38 (.015)DE, DA, DB, DC9, 15, 25, 37D1*******,42 (.489)14,35 (.565)DD50D1*******,47 (.609)17,09 (.673)Kit consists of 1plate, 1screw, 1lock washer,1hex nutOrder 2 kits per connector Spring Latch AssemblyShell Size Layout Part Number A ±0,38 (.015)B ±0,38 (.015)C ±0,51 (.020)DE, DA, DB, DC9, 15, 25, 37D1*******,42 (.489)14,35 (.565)18,59 (.732)DD50D1*******,49 (.609)17,09 (.673)18,59 (.732)Kit consists of 1spring, 1screw, 1bracket, 1lock washer, 1hex nut Order 2 kits per connector Front panel mounting* Dimension does not apply to rear panel mounting.MOUNTING PLATEMAX1,14 ± 0,13± .005)Kit consists of 2 studs, 2 heads, 1tube retaining compoundOrder one kit per connector Part Number:D110550Materials and Finishes Material:Stainless SteelKit consists of 2 posts, 2 hex nuts, 2 lock washersOrder one kit per connector Part Number:D110551Materials and Finishes Material:Stainless Steel Treatment:Passivated NOTE: Jackpost is not compatible with rear-panel mount connectors.Jackscrew/Jackpost AssembliesJackpost AssemblyJackscrew AssemblyJackpost AssemblyJackscrew AssemblyITT Cannon offers the largest variety of locking and latching hardware. Refer to the accessories selection guide on pages 198-199 for use with ITT Cannon Connectors.HEAD,。
V 系列【 w机型 】医用氧气机 产品使用说明书
·使用前请仔细阅读本说明书·本公司保留说明书解释权·产品外观请以实物为准·阅后请与发票一并妥善保存·如遇产品技术或软件升级，恕不另行通知·说明书修订日期：20210506网址：V 系列【 w机型 】医用氧气机 产品使用说明书医疗器械注册证编号/产品技术要求编号：辽械注准 20162080087生产许可证编号：辽食药监械生产许********号注册人 / 生产企业 / 售后服务单位：沈阳海龟医疗科技有限公司住所/生产地址：沈阳市沈北新区道义经济开发区沈北路76-39号 邮编：110136网址： 全国免费服务热线：400 655 6306目 录前言 (1)安全须知 (1)注意事项 (2)产品简介 (4)产品使用环境 (4)适用范围 (4)结构组成 (4)型号说明 (5)技术参数 (5)名称及功能 (6)使用操作步骤 (7)报警及提醒功能 (9)维护保养说明 (10)故障及排除 (11)运输和贮存条件 (11)使用期限 (11)装箱清单（含可更换部件） (12)配套产品规格要求 (12)出口标称压力为零时氧浓度与流量函数图 (13)0-4000m海拔范围内的不同气压条件下，氧浓度随流量变化表 (13)出口标称压力为零时和7kPa下规定的设定值以升/分表示的流量 (14)符号及含义 (15)氧气机接线图 (16)电磁兼容性信息 (17)报警及信息信号 (21)分类 (22)前 言安全须知感谢您购买本产品，希望我们的产品能让您满意。
本使用说明书叙述了产品的功能、操作步骤、注意事项、以及基本故障排除等内容。
为了保证您有效使用本机器，请务必在使用之前仔细阅读本使用说明书。
请注意本使用说明书中有些图例与您在机器中看到的可能不同。
本说明书中提到的氧气吸入器、雾化器、吸氧管、电池、电源线等部件均应符合配套产品规格要求。
警告:使用前必须卸下底座上的压缩机固定螺栓。
KUKDO 产品指南说明书
BEYOND EXPECTATION & BEYOND LIMITATIONPRODUCT GUIDE61, Gasandigital 2-ro, Geumcheon-Gu, Seoul 153-802, KoreaInternational business : Tel +82-2-3282-1540 Fax +82-2-869-4409Domestic Sales : Tel +82-2-3282-1500 Fax +82-2-869-4944R&D Center : Tel +82-2-3282-1560 Fax +82-2-3282-1586 E-mail:***************Rev. No. 19.4si Chang Lee, PresidentApr. 2002 Establishment of KUKDO CHEMICAL (KunShan) CO., LTD. in China Nov. 2003Completion of KunShan factory for Epoxy resin and Polyol in China J ul. 2004 Completion of Busan factory for Epoxy resin and System Polyol in Busan Mar. 2008 Acquisition of HAJIN CHEM TECHNov. 2008 Completion of 40KT of Liquid Epoxy resin in IksanDec. 2008 Awarded 200 Million Dollar Export Tower Prize (45th Trade Anniversary)Nov. 2010 Awarded 2010 Global Excellent Management by JMACApr. 2011 Obtained Customs approved registered exporter Certificate by Customs Sep. 2011 Obtained AEO(Authorized Economic Operator) Certificate by Customs Dec. 2011 Awarded 300 Million Dollar Export Tower Prize (48th Trade Anniversary)Dec. 2011A warded Korean World-class Product Award 2011 by Knowledge Economy Feb. 2013Establishment of NICHIDO CHEMICAL CO., LTD.gLoBaLsaLesnetWorks*1 Gardner Holdt Method, Butyl Carbitol NV 70% Solution *2 Reference data *3 Gardner Holdt Method, Butyl Carbitol NV 40% Solution3) High Viscosity Type*1 Gardner Holdt Method, Butyl Carbitol NV 40% Solution *2 Ball & Ring Method *3 Reference data *4 Approved by F .D.A2. standard solid typeHead Office Iksan FactoryBisPHenoL-a tyPe ePoxy resin*1 Reference data1) Low Viscosity Type1. standard Liquid type*1 Reference data2) Medium Viscosity Type2) Low Viscosity, High Flow Grade*1 I.C.I Viscometer *2Ball & Ring Method*1 I.C.I Viscometer *2 Ball & Ring Method *3 Brookfield Viscometer at 25ºC, Butyl Carbitol NV 40% Solution *4 Gardner Holdt Method, Butyl Carbitol NV 40% Solution3) High Molecular Weight Grade4) Special Grade*1 I.C.I Viscometer *2 Ball & Ring Method *3 Melt Viscosity at 175ºC *4 Mettler Method *5Gardner Holdt Method, Butyl Carbitol NV 40% Solution*1 Ball & Ring Method5) Half-capped Epoxy Resin3. solution of solvent epoxy resin*1Gardner Holdt Method1) General Grade4. Powder Coating epoxy resin*1 I.C.I Viscometer *2 Ball & Ring Method *3 Melt Viscosity at 175ºC*Curing condition : Preheating at 130ºC × 20 mincoating).KD-4014SYSTEM0.2%residual Bisphenol-aKD-214M&KD-407SYSTEM4.7%BisPHenoL-f tyPe ePoxy resin*1 Ball & Ring Method *2 Gardner Holdt Method, Butyl Carbitol NV 40% Solution*1 I. C. I Viscometer *2 Brookfield Viscometer at 25ºC, Butyl Carbitol NV 40% Solution *3 Ball & Ring Method *4 Ph-OH E.W. *5 Approved by F .D.A6. n=0 free, BPa free type*1 Total-CI : Potentiometric titration *2 Brookfield Viscometer at 52ºC (Reference data) *3 Gardner Holdt Method, Butyl Carbitol NV 60% Solution*4 GPC Data7. High Purity-Low Chlorine epoxy resin*1 I.C . I Viscometer *2 Melt Viscosity : I. C . I Viscometer at 175°C *3 Gardner Holdt Method, Butyl Carbitol NV 40% Solution *4 Ball & Ring Method 5. Low BPa type*1 Ball & Ring Method *2 43phr on KD-211D, at 180ºC *3 73phr on KD-211D, at 180ºC *4 130phr on KD-211D, at 180ºC*5 Melt Viscosity : I.C.I Viscometer at 125ºC *6 Melt Viscosity : I.C.I Viscometer at 150ºC *7 51phr on KD-211D, at 180ºC (Reference data) *8 Reference data9) Phenol Excess Type Curing Agentnon-HaLogen fLaMe retardant ePoxy resinBroMinated ePoxy resin*1 Ball & Ring Method *2 Brookfield Viscometer at 40ºC *3 Brookfield Viscometer at 25ºC *4Mw (Reference data)*1 Ball & Ring Method1. o-Cresol novolac type*1 Ball & Ring Method *2 Non-Volatile Content(wt.%)novoLaC ePoxy resinGradeEEW (g/eq)Viscosity (cps@25ºC)Color (G,max.)Characteristics/UseYDF-1020160-1802,000-3,0001Low viscosity2. Low viscosity type*1 Ball & Ring Method3. solid typefLexiBLe ePoxy resin*1 Gardner Holdt Method *2 Brookfield Viscometer at 50ºC1. dimer acid Modified epoxy resin*1 Brookfield Viscometer at 50ºC2. rubber Modified epoxy resinMuLti-funCtionaL ePoxy resin*1 Ball & Ring Method4. BPa-novolac type*1 Ball & Ring Method *2 Brookfield Viscometer at 25ºC5. dCPd type*1 Ball & Ring Method *2 Non-Volatile Content(wt%)6. xylok typeGradeEEW (g/eq)Softening Point*1(ºC)Characteristics/UseKDXN-1055225-25550-60Flame retardance, Low moisture absorption, Electronic application*1 Ball & Ring Method3. Low viscosity Phenol novolac typeGradeEEW (g/eq)Solution Viscosity*1(25ºC)Color (G,max.)Characteristics/UseKDPN-1020165-185D-G3High heat resistance, Low viscosity*1 Gardner Holdt Method, Butyl Carbitol NV 60% Solution7. Multi-functional novolac typeGradeEEW (g/eq)Softening Point*1(ºC)Characteristics/UseKDMN-1065162-17665-75High heat resistance, EMC, PCB, etc*1 Ball & Ring Method2. Phenol novolac type*1 Gardner Holdt Method, Butyl Carbitol NV 60% Solution *2 I.C.I Viscometer at 150ºC *3 Brookfield Viscometer at 60ºC *4 Non-Volatile Content(wt.%) *5 Brookfield Viscometer at 52ºCePoxy resin for P.C.M.*1 Gardner Holdt Method *2 EEW(g/eq) *3 Reference dataePoxy Modified PoLyoL (isoCyanate Curing tyPe)GradeOH Value (mgKOH/g)Solution Viscosity (25ºC)Non-Volatile Content (wt.%)Characteristics/UseYU-300100-130Z-Z 460±1Tar-urethane coating, MIBK/Toluene=1/1fiLaMent Winding, LaMinating ePoxy resinMoLding ePoxy resin*1 Brookfield Viscometer at 120ºC3. urethane Modified epoxy resin*1 Brookfield Viscometer at 40ºCuv Curing tyPe ePoxy resin*1 Gardner Holdt MethodLoW teMPerature Curing tyPe ePoxy resin*1 Gardner Holdt Method, Butyl Carbitol NV 40% solutionPHenoxy resin*1 Gardner Holdt Method, MEK NV 40% solution *2 Mw(Reference data) *3 Tg(ºC), DSC(Reference data)* S ubstrate condition : No sanding treatment on Aluminum * Mixing ratio : KSR-177/G-640=100/53 YD-128 / G-640=100/59* Curing condition : 80°C for 2hrUnit: kg/cm²ItemKSR-177YD-128Shear adhesion strength80.834.1* Test Method : ASTM D 3359B* Mixing ratio : KSR-276M70/G-640=16phr, YD-011X70 / G-640=16phr * Curing condition : 3days at RT × 80°C for 1hr * Curing agent : Kukdo Domide G-640* Film thickness: 20㎛* S ubstrate condition : No sanding treatment* Mixing ratio : KSR-177/G-640=100/53,YD-128 / G-640=100/59* Curing condition : 80°C for 2hr* Curing Condition : Room T emperature×14 days * Plate : Cold Rolled Steel (0.7T)* EEW : Epoxy Equivalent Weight (solution base) * AHEW : Active Hydroxyl Equivalent Weight (solution base)*1 : Polyamide Hardener*2 : Polyamide Adduct T ype Hardener *3 : Phenalkamine Hardener*1 A : Adhesion test (cross-hatch) *2 B : Dupont test(Impact Test, D/R), condition : ½ inch × high(cm) × 1,000 g *3 C : Erichsen Test(mm) *4 F : FailedWaterBorne ePoxy resin*1 Basis of solid contentreaCtive diLuent*1 APHA ColorGradeEEW(g/eq)Viscosity (cps@25ºC)Characteristics/UseKDSF-180300-3503,000-6,000High adhesive, Low viscosity3. BPa-Po epoxy resin4. Modified Weatherable epoxy resintri-funCtionaL ePoxy resin*1 Reference datatetra-funCtionaL ePoxy resin*1 Softening Point (ºC) : Ball & Ring MethodPoLyaMide & aMidoaMine tyPe*1 TAV : Total Amine Value(0.1N-HCl Method) *2 Viscosity : cps at 40ºC *3 TAV : Total Amine Value(0.1N-HClO 4 Method) *4 Viscosity : Gardner Holdt Method *5 A.H.E.W. : Solution basesuMMary of Hardener ProduCt grouPaLiPHatiC aMine Modified tyPe*1 TAV : Total Amine Value(0.1N-HCl Method)PoLyaMide adduCt tyPe*1 TAV : Total Amine Value(0.1N-HCl Method) *2 N.V : Non-Volatile Content(wt.%) *3 TAV : Total Amine Value(0.1N-HClO 4 Method)*4 Viscosity : Gardner Holdt Method *5 A.H.E.W. : Solution base*1 TAV : Total Amine Value (0.1N-HClO 4 Method) *2 A.H.E.W : Solution basearoMatiC aMine Modified tyPePHenaLkaMine tyPeCyCLoaLiPHatiC aMine Modified tyPe*1 TAV : Total Amine Value(0.1N-HCl Method) *2 TAV : Total Amine Value(0.1N-HClO 4 Method)SIHWA Factory BUSAN Factory CHINA Factory。
产品说明书范文【三篇】
产品说明书范文【三篇】产品说明书范文【三篇】【篇一】1.概述本产品为LED-901充电式手电筒，公司遵循国家行业执行标准：GB7000.13-1999，确属本公司产品质量问题，自购置之日起保修期为3个(非正常使用而致使产品损坏，烧坏的，不属保修之列。
)2.技术特性●本产品额定容量高达900mAH。
●超长寿命电池，高达500次以上循环使用。
●采纳节能，高功率，超长寿命的LED灯泡。
●充电爱护:充电状态显示红灯，充电满显示绿灯。
3.工作原理LED灯由电池供应电源而发光，此电池充电后可重复使用。
4.结构特性：(略)6.使用和操作●充电时灯头应朝下，将手电筒沟通插头完全推出，直接插入AC110V/220V电源插座上，此时红灯亮起，表示手电筒处于充电状态;当充电布满时，绿灯亮起，表示充电已布满。
●使用时推动开关按键，前档为6个LED灯亮，中间档为3个LED灯亮，后档为关灯。
●布满电，3个LED灯可连续使用约26个小时，6个LED灯可连续使用16个小时7.故障分析与排解①使用过程中若发觉灯不亮或者光线很暗，则有可能是电池电量不足，假如充电后灯变亮则说明手电筒功能正常，假如充电后仍旧不亮，则有可能是线路故障，可以到本公司自费修理。
②使用几年后若发觉充电后灯不亮，则极有可能是电池寿命已到，应准时到本公司自费更换。
8.修理和保养●在使用过程中，如LED灯泡亮度变暗时，电池处于完全放电状态，为爱护电池，应停止使用，并准时充电(不应在LED灯泡无光时才充电，否则电池极易损坏失效。
)●手电筒应当常常充电使用，请勿长期搁置，如不常常使用，请在存放2个月内补充电一次，否则会降低电池寿命9.留意事项●请选择优质插座，并保持平安规范充电操作。
●产品充电时切勿使用，以免烧坏LED灯泡或电源内部充电部件。
●手电筒不要直射眼睛，以免影响视力。
(小孩应在大人指导下使用。
)●勿让本产品淋雨或者受潮。
●当充电布满时(绿灯亮起)，请马上停止充电，避开烧坏电池。
O188 指说 产品说明书
O188指说产品说明书免责声明请您在使用本手册描述的产品前仔细阅读手册的所有内容，以保障产品的安全有效地使用。
阅读后请将本手册妥善保存以备下次使用时查询。
一旦使用本手册所述产品，即视为您已经仔细阅读免责声明与警告，理解、认可和接受本声明全部条款与内容，您承诺仅出于正当目的使用本产品，对使用本手册所述产品以及可能带来的后果承担相应的责任。
请勿自行拆卸本产品或撕毁产品上的封标，否则浩创科技不承担保修或更换产品的责任。
本手册中的图片仅供参考，如有个别图片与实际产品不符，请以实际产品为准。
本手册包含的所有信息和图片除特别标明之外，版权归浩创科技及其关联公司，未经书面许可，任何单位及个人不得以任何方式或理由对本手册全部或部分内容进行任何形式的摘抄、复制或与其它产品捆绑使用、销售。
本手册所述产品中可能包括浩创科技或第三方享有版权的软件，除非获得相关权利人的书面许可，否则任何单位或者个人不能以任何形式对前述软件进行复制、分发、修改、摘录、反编译、反汇编、解密、反向工程、出租、转让、分许可以及其它侵犯软件版权的行为。
本手册及产品所有相关的文档最终解释权和修改权归浩创科技，如有更新，恕不另行通知，请您访问官方网站或查阅最新版产品手册以获取最新的产品信息。
一、外观介绍二、产品明细及用途产品名称数量指说1个通用充电线（长）1根磁吸充电线（短）1根充电收纳盒1个说明书1本三、基本参数型号O188重量10g（不含充电收纳盒）尺寸32.9mm*23.7mm*29.9mm指环套弹性材质，可根据手指粗细调节触摸按键前进、后退、双击、单击蓝牙Bluetooth V5.1+BR+EDR+BLE 蓝牙传输距离>10mLED提示灯RGB LED(可编程)电池（可充电）************充电时间 2.5小时充电方式便携式充电收纳盒充电盒电池***********充电盒充电方式Micro USB工作时间24小时防护等级IP54工作温度-10℃至50℃工作湿度0%-95%RH（无冷凝）四、操作指南1．如何佩戴指说？将指说底部含有两个金属圆点一侧朝向手腕方向，戴入食指，指说顶部为触控区域。
Trigonox 99-CH75 商品说明说明书
Product Data SheetTrigonox 99-CH75Cumyl peroxyneodecanoate, 75% solution in odorless mineral spiritsTrigonox® 99-C75 is an initiator (75% active ingredient in odorless mineral spirits) for (co)polymerization of ethylene, vinyl chloride and vinylidine chloride.CAS number26748-47-0EINECS/ELINCS No.247-956-7TSCA statuslisted on inventoryMolecular weight306.4Active oxygen contentperoxide5.22%SpecificationsActive oxygen 3.86-3.97 %Appearance Clear liquidAssay74.0-76.0 %Color30 Pt-Co / APHA max.Free acid as neodecanoic acid30 %Hydroperoxides as CHP≤ 0.15 %Inorganic + organic hydrolysable chloride≤ 150 mg/kgCharacteristicsDensity, -10 °C0.962 g/cm³Viscosity, -10 °C74.6 mPa.sApplicationsPolymerization of ethylene: Trigonox® 99-CH75 is an efficient initiator for the production of Low Density Polyethylene (LDPE). It is used both for tubular and autoclave processes. In most cases a combination with other peroxides is used to ensure a broad reactivity range. Polymerization of vinyl chloride: Trigonox® 99-CH75 is used as an initiator for the suspension and mass polymerization of vinyl chloride between 40°C and 65°C. Trigonox® 99-CH75 is often combined with less active peroxides such as peroxydicarbonates (e.g. Perkadox 16) or diacylperoxides (e.g. Laurox) to increase reactor efficiency.Half-life dataThe reactivity of an organic peroxide is usually given by its half-life (t½) at various temperatures. For Trigonox® 99-CH75in chlorobenzene:0.1 hr75°C (167°F)1 hr56°C (133°F)10 hr38°C (100°F)Formula 1kd = A·e-Ea/RTFormula 2t½ = (ln2)/kdEa114.59 kJ/moleA 3.12E+14 s-1R8.3142 J/mole·KT(273.15+°C) KThermal stabilityOrganic peroxides are thermally unstable substances, which may undergo self-accelerating decomposition. The lowest temperature at which self-accelerating decomposition of a substance in the original packaging may occur is the Self-Accelerating Decomposition Temperature (SADT). The SADT is determined on the basis of the Heat Accumulation Storage Test.SADT10°C (50°F)Emergency temperature (Tₑ)0°C (32°F)Control temperature (Tc)-10°C (14°F)Method The Heat Accumulation Storage Test is a recognized test method for thedetermination of the SADT of organic peroxides (see Recommendations on theTransport of Dangerous Goods, Manual of Tests and Criteria - United Nations, NewYork and Geneva).StorageDue to the relatively unstable nature of organic peroxides a loss of quality can be detected over a period of time. To minimize the loss of quality, Nouryon recommends a maximum storage temperature (Ts max.) for each organic peroxide product.Ts Max.-20°C (-4°F)Note When stored under these recommended storage conditions, Trigonox® 99-CH75will remain within the Nouryon specifications for a period of at least 3 months afterdelivery.Packaging and transportTrigonox® 99-C75 is packed in non-returnable, one gallon polyethylene containers of 7 lb net weight (4 per case) and in five gallon polyethylene containers of 35 lb net weight. Both packaging and transport meet the international regulations. For the availability of other packed quantities consult your Nouryon representative. Trigonox® 99-C75 is classified as Organic peroxide type D; liquid, temperature controlled; Division 5.2; UN 3115.Safety and handlingKeep containers tightly closed. Store and handle Trigonox® 99-C75 in a dry well-ventilated place away from sources of heat or ignition and direct sunlight. Never weigh out in the storage room. Avoid contact with reducing agents (e.g. amines), acids, alkalis and heavy metal compounds (e.g. accelerators, driers and metal soaps). Please refer to the Safety Data Sheet (SDS) for further information on the safe storage, use and handling of Trigonox® 99-C75. This information should be thoroughly reviewed prior to acceptance of this product. The MSDS is available at /sds-search.Major decomposition productsCarbon dioxide, 2-Phenylisopropanol, Isomers of neonaneAll information concerning this product and/or suggestions for handling and use contained herein are offered in good faith and are believed to be reliable.Nouryon, however, makes no warranty as to accuracy and/or sufficiency of such information and/or suggestions, as to the product's merchantability or fitness for any particular purpose, or that any suggested use will not infringe any patent. Nouryon does not accept any liability whatsoever arising out of the use of or reliance on this information, or out of the use or the performance of the product. Nothing contained herein shall be construed as granting or extending any license under any patent. Customer must determine for himself, by preliminary tests or otherwise, the suitability of this product for his purposes.The information contained herein supersedes all previously issued information on the subject matter covered. The customer may forward, distribute, and/or photocopy this document only if unaltered and complete, including all of its headers and footers, and should refrain from any unauthorized use. Don’t copythis document to a website.Trigonox®, Perkadox and Laurox are registered trademarks of Nouryon Functional Chemicals B.V. or affiliates in one or more territories.Contact UsPolymer Specialties Americas************************Polymer Specialties Europe, Middle East, India and Africa*************************Polymer Specialties Asia Pacific************************2022-6-30© 2022Polymer production Trigonox 99-CH75。
宁波池洋测氧测爆操作说明书
宁波池洋测氧测爆操作说明书1. 简介本操作说明书旨在指导使用者正确、安全地进行宁波池洋测氧测爆操作。
宁波池洋是一个重要的水域，对其进行氧测爆操作有助于了解水体中的溶解氧含量以及可能存在的爆炸性气体。
2. 操作准备在进行宁波池洋测氧测爆操作前，需要完成以下准备工作：2.1 工具和设备•氧浓度仪：用于测量水体中的溶解氧含量。
•爆炸性气体检测仪：用于检测水体中可能存在的爆炸性气体。
•清洁布：用于清洁仪器表面。
•记录表格和笔：用于记录实验数据。
2.2 安全措施•确保操作者穿戴个人防护装备，包括防护眼镜、手套和实验服。
•在进行实验前，确保设备处于正常工作状态，并做好相关校准工作。
•在操作过程中，遵循实验室安全规范，如禁止吸烟、禁止饮食等。
3. 操作步骤3.1 准备工作1.将氧浓度仪和爆炸性气体检测仪放置在操作台上，并确保其连接到电源。
2.使用清洁布清洁仪器表面，确保无尘和污渍。
3.2 测量溶解氧含量1.打开氧浓度仪的电源，等待其启动。
根据仪器说明书进行相关设置。
2.将氧浓度仪的探头缓慢放入宁波池洋水体中，确保探头完全浸入水中。
3.等待一段时间（根据仪器说明书），直到氧浓度仪显示稳定的溶解氧含量数值。
4.记录下该次测量的溶解氧含量数值，并将其填入记录表格中。
3.3 检测爆炸性气体1.打开爆炸性气体检测仪的电源，等待其启动。
根据仪器说明书进行相关设置。
2.将爆炸性气体检测仪的传感器缓慢放入宁波池洋水体中，确保传感器完全浸入水中。
3.等待一段时间（根据仪器说明书），直到爆炸性气体检测仪显示稳定的气体浓度数值。
4.根据仪器说明书，判断水体中是否存在爆炸性气体，并记录下该次测量的结果。
4. 数据处理与分析1.将测得的溶解氧含量数据和爆炸性气体检测结果整理成表格或图表，以便后续分析和比较。
2.使用统计方法对数据进行分析，如计算平均值、标准差等。
3.根据数据分析结果，对宁波池洋水质进行评估，并提出相应的建议和改进措施。
护肝宁胶囊(晨牌)的说明书
护肝宁胶囊(晨牌)的说明书
肝胆胰腺类疾病往往都是吃出来的，人体消化不了这么多食物，紧接着全部囤积在体内，形成脂肪，对于肝胆胰腺的压力也很大。
因此生活中难免造成肝胆胰腺类的疾病，药物治疗很关键，选择护肝宁胶囊(晨牌)进行肝胆胰腺类的疾病治疗是目前大多数人
都比较看好的方法，下面我们来看看对于护肝宁胶囊(晨牌)的介绍吧。
【药品名称】
通用名称：护肝宁胶囊
商品名称：护肝宁胶囊(晨牌)
拼音全码：HuGanNingJiaoNang(ChenPai)
【主要成份】垂盆草、虎杖、丹参、灵芝。
【性状】本品为胶囊剂，内容物为棕褐色的颗粒及粉末；味苦、微酸、涩。
【适应症/功能主治】清热利湿、益肝化瘀、舒肝止痛；退黄，降低丙氨酸氨基转移酶。
用于急性肝炎及慢性肝炎。
【规格型号】0.35g*36s
【用法用量】口服，一次4～5粒，一日3次。
【不良反应】尚不明确。
【禁忌】孕妇忌服。
【注意事项】尚不明确。
【药物相互作用】如与其他药物同时使用可能会发生药物相互作用，详情请咨询医师或药师。
【贮藏】密封。
【包装】0.35g*36s/盒。
【有效期】24 月
【批准文号】国药准字Z20050804
【生产企业】江苏晨牌药业集团股份有限公司
采用护肝宁胶囊(晨牌)治疗肝胆胰腺疾病的效果非常显著，以上的内容就是关于护肝宁胶囊(晨牌)的介绍，您对于它的治疗特点和用药原则都清楚了吗?治疗肝胆疾病我们一定不能掉以轻心，
这类疾病很有可能引起更多的并发症出现，及时治疗是很关键的，用药方面也一定要选择正规的药物。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
临朐县辰阳自动门加工厂自动旋转门设备及安装临朐县辰阳自动门加工厂前言各位领导、评委你们好！首先对企业给予我们的这次机会表示衷心的感谢！并对业主和各位专家表示深切的敬意！感谢业主，各位专家对我们的信任和支持。
对于贵方的旋转门工程。
我们对该工程投标特别重视，对业方提供的招标文件和有关资料，经过认真的学习和研究，认为我们有能力有信心来参加该工程的建设，并愿意接受贵方的要求，保证始终提供优秀的服务。
今报送我方的企业资料，请审查不当之处，请指正。
谢谢！临朐县辰阳自动门加工厂企业简介临朐县辰阳自动门加工厂，是生产、安装两翼旋转门、三翼旋转门、四翼旋转门、玻璃门、肯德基门与一体的专业厂家。
我单位引进国内外先进技术装备及测试设备，并拥有一批实力强，经验丰富的设计人员和一支经过专业训练，素质优良的职工队伍，有一套适应现代化生产管理体制和完整的售后服务措施。
我们以“质量第一、信誉第一、用户至上”作为质量方针，以“出厂产品合格率100％”作为质量目标。
近年来，规模不断发展装大，面向市场并加强技术人员、管理人员的培训，使产品质量有了可靠的保证。
所安装的各项工程，从未发生过质量安全问题，受到了用户的一致好评。
两翼旋转自动门配置报价单两翼旋转自动门安全门配置单型号CY-3780NO 部品名称部品型号数量材质性能/规格供应商/加工商单价(元) 备注1 动作感应器EL Y-UP 4套进口/内藏式红外线感应BEA(比利时品牌)Microcell 1 4套进口/双排非接触式安全保护BEA(比利时品牌)2 红外线对射防夹、防碰优越感器3 红外线防夹传感器Air30 2套进口/红外线感应毕澈(瑞士品牌)4 挤压式防夹传感器4套进口/接触式感应瑞士毕澈5 滑环1套全盛6 传动马达2套220V、50Hz、0.37KW LENZE(德国品牌)7 定位感应器N110-G18-AN6X 4套图尔克8 变频调速系统VFO 1套松下9 中控电脑VPO 1套松下10 急停按钮2套和泉(日本品牌)11 残障按钮2套和泉(日本品牌)12 平开感应门1套日本富士山13 镭射天花灯12只12V、35W 雷士、广东14 制动器101 2 台湾千代15 触摸屏GT01 1套松下16 吊顶板10块氟碳铝板板厚1.2、防火7级广东17 封顶板1套双贴面高密青岛大星木业度板18 毛刷足量上海两翼旋转自动门安全门配置单型号CY-3780NO 部品名称部品型号数量材质性能/规格供应商/加工商单价(元) 备注19 门体框架1套铝型材GB6063 山东铝厂20 氟碳喷涂上海衡峰门体表面处理工艺，氟碳颜色可选21 门扇玻璃6页钢化玻璃8mm 山玻集团22 曲壁玻璃8页弧形热弯玻璃10mm 山玻集团23 展箱玻璃6页弧形热弯玻璃6mm 山玻集团24 转门机械配件1套自制标准配件25 轴承1组NSK(日本品牌) 主动轮、从动轮、滑环、展箱门扇26 转门展箱2套青岛分列转门两侧27 转门承重梁1套标准工字钢青岛28 随门物品橡胶条1套等29 地弹簧2埠GMT30 拉手2付GMT31 边门玻璃2页8mm钢化山玻集团32 玻璃胶3箱使你佳33 加工制作按装费34 运输费35 直接费36 利润(5％)37 合坟38 外包304不锈钢拉丝板90丝39 合计注：以上报价不含税票。
临朐县辰阳自动门加工厂两翼自动旋转门功能特点说明立面图平面图a 帽头：高度300mm----400mmb 曲壁立柱：104mm×70mmc 平滑门：日产富士机组d 曲壁：10mm热弯钢化或5mm+5mm夹胶热弯玻璃e 展箱：双锥型展箱，可摆设各种装饰品。
A 转门开口尺寸：1800mm----2400mmC 平滑门开口尺寸：1700mm----2300mmD 外直径：3600mm----4800mm一、二翼自动旋转门概述自动旋转门状态自动平移状态A、标准尺寸外直径 A 门扇高度项蓬高度D=3600mm D＝4200mm D＝4800mm 1800mm2100mm2400mm2200mm-2800mm2200mm-2800mm2200mm-2800mm300mm-400mm300mm-400mm300mm-400mm注：以上规格为标准尺寸，用户可根据实际需要订制。
B、标准外饰材质1、4K发丝不锈钢1.0mm、1.2mm、1.5mm板材(可选)2、8K镜面不锈钢1.0mm、1.2mm、1.5mm板材(可选)3、4K发丝钛金不锈钢1.0mm、1.2mm板材(可选)4、铝合金氟碳喷涂工艺C、标准装配1、双展箱：锥型、带尾翼、双侧式。
配门扇及锁，照明灯各一套。
2、中间平滑自动门：转门停转后，在功能转换钥匙控制下，中间平滑自动门可自动打开关闭，适用于消防通道及通过大型物体。
外直径开门尺寸(C) 门扇高度D=3600mm D＝4200mm D＝4800mm 1700mm2100mm2300mm2200mm-2800mm2200mm-2800mm2200mm-2800mm注：以上规格尺寸，可根据用户要求订制不同直径的旋转门。
D、运转转速1、标准正常转速：3-5转/分2、供残疾人行走及移动大件物体正常转速：1.5-2转/分。
3、智能转速提升功能(可选)：当启动传感器探测有行人通过转门时，门可由正常的慢速自动提升到标准速度上运行；当传感器无信号输出，则旋转速度自行隆至慢速经济运行。
此功能缩短了大人流量通过时的速度提升时间。
E、玻璃1、旋转门曲壁固定玻璃：10mm弧形、8mm弧形、5+5mm夹胶弧形玻璃(可选)。
2、中间平滑自动门玻璃：8mm钢化安全玻璃。
3、双锥型展箱玻璃：8mm钢化安全玻璃。
F、密封毛刷1、旋转吊顶与固定顶蓬天花内侧为毛刷密封。
2、旋转门体与接触面(地面、曲壁)为毛刷密闭毛刷为特制黑色羊毛。
二、电气传动控制系统A、交流AC220V、50Hz、0.25KW或0.37KW型马达驱动，配过热保护以及测速反馈装置、减速制动装置。
反馈装置、减速制动装置。
功率：＜550W额定电流：＜12A额定转速：1380rad/min减速比：1：60：6B、中央电脑控制单元松下电脑可编程序控制器PLC(*)电压：AC220V输出：±24V1/0点数：30C、自动控制系统启动感应器探测到行人后输出信号给PLC，根据程序判断及运算，发出指令给AC MOTOR，旋转门开始旋转(速度可调)。
如安全保障功能之一动作或急停动作，则PLC发出信号输出该MOTOR电机减速或停转。
注：可根据控制要求更换PLC型号。
D、红外启动感应探测器内藏式、明装式(可选)安装于出/入口顶蓬下沿内侧(内藏式)，若安装在出/入口项蓬上外侧(明装式)，探测范围均可调。
E、残疾人慢速(经济转速)及急停功能当按动残疾人慢速按钮后，转门转速立刻由标准正常转速降至慢速，并开始延时。
延时过后，如有行人继续行走，转速恢复正常，当按动紧急停止按钮，则转门立刻停止转动。
C、旋转门三种自动停止定位方式1、正常水平轴方向2、正常斜线方向停止门扇停在开的位置，红外控头检测到有人通行门即开始运转。
3、正常轴垂直方向停止(关闭式)门扇旋转至关闭位置，装上电子机械锁，此时转门进入防盗、防风状态。
(以上根据用要求通过钥匙功能转换开关选定)。
中央平滑门能自动打开，提供畅通无阻恢复正常或火警系统不再提示紧急事故，转时，门立即开始运转。
三、电气安全防护功能A、运转展箱防碰安全功能(可选)此安全防碰传感器为高位非接触式，安装于展箱顶部。
当运行的展箱接近行人背后时，旋转体立刻降速并停止转动(检测范围可调)。
B、中间门扇安全防碰功能(可选)为低位非接触式红对射电眼传感器，安装于每扇门扇底边框，当行入脚跟或某物体遮挡电眼时。
该传感器动作，旋转体立刻降速并停止转动。
C、狭角防夹行人安全功能该传感器安装于顶篷下沿内侧(出/入口各一只)，靠近旋转门出/入口曲壁150mm处。
当行人或物体处于该传感器下时，运转的门体在接近曲壁立柱大于30度角位置停下，避免旋转门体将行人夹伤。
该传感器为高位非接触式。
四、固定框架(含外饰部分)序号品名材质规格特点1 BOON EDAM标准转门框架型材铝合金成型壁厚6.0-8.010.0-12.0BOON EDAM标准，自行研制开发型材2 BOON EDAM标准转门门扇型材铝合金成型壁厚2.5-3.0BOON EDAM标准，自行研制开发型材3 外饰表面8K镜面不锈钢4K发丝不锈钢铝合金表面氟碳喷涂1.5-2.0厚板1.5-2.0厚板V-CUT加工工艺三遍高温静电工艺永不褪色4 密封毛刷羊毛精选EOONEDAM 标准d＝7.0，h＝5.0密封良好5 BOON EDAM二翼旋转门上挂导轨高强度铝合金成型壁厚4.0-5.0U型BOON EDAM标准，自行研制开发6 收口圈材铝合金成型壁厚4.0-6.0U型BOON EDAM标准，自行研制开发7 天花吊项铝合金板壁厚2.5mm 表面氟碳喷涂或喷塑五、旋转体部分序号品名材质规格特点1 BOON EDAM二扇式旋转门双展箱展箱玻璃铝合金成型浮法钢化平板及热弯玻璃d=1.5mmd=8mmBOON EDAM标准自行研制2 铝合金成型门框门体玻璃钢化或夹层玻璃壁厚4.0-6.0d=5+5mmBOON EDAM标准自行研制3 BOON EDAM 进口支撑轮强化复合工程塑料内置密封轴承￡＝125mmL=50mmBOON EDAM标准自行研制4 展箱机械锁铸铁钥匙开启5 自动平滑门导轮强化尼龙￡＝35mm六、电气部分序号品名材质规格特点1 电机变速总成变频电机及变速箱1n=1.6AUn=220VW=370W*2IS9001 认证运行平稳静音设计2 电脑主控制器及软件PLC可编程电脑控制系统NBO-241:24V DC60点0：结点60点100V-240V AC工作容量大易操作维护BOONEDAM自动旋转门程序进行3 微电脑分控制器变频驱动DamfossVLT2800 5.1A3x220-240V驱动平稳可编程序4 工作方式选择控制器国际标准平滑自动门电脑控制器国际标准微电子控制器与钥匙控制器联动5 疏散门控制器贺多龙平滑自动门电脑控制器专业IC芯片集成与钥匙控制器联动6 启动探测器BIR CHERISO9001认证专业微电子红外光电优越感器启动感应器7 红外线传感器BIR CHERISO9001认证专业微电子红外光电优越感器门扇防夹行人感应器(狭角)8 红外线传感器BIR CHERISO9001认证专业微电子红外光电优越感器门扇防夹行人感应器9 停电/火警处理功能分控制器特殊与消防联动控制门转动旋转门停止转动中间平滑自动门自动打开10 UPS系统(选配)附件后备直流电源特殊与消防联动控制门转动消防断电时旋转门位停转并平滑自动门自动打开11 紧急停按键附件工程塑料干接点式带自锁紧停时按下旋转门停转12 残疾人按键附件工程塑料干接点、点触式按下旋转门慢速时旋转13 故障指示器* 附件触摸屏显示指示故障显示14 转速自动提升控制器*附件特殊微电子控制器联动PLC按下控制键旋转门处于自由慢速等待旋转，一旦发现人则立刻提升转速15 各类保险附件速熔管式及总空开8A、10A、15A过流保护过热保护16 电源滑环3环接触式220V供旋转门用电火线、零线、接地线17 信号滑环9环银点封闭式27路编码、解码供旋转门各种信号传输(注：*号表示选配功能及附件)附件1：《企业技术要求规定》说明一、名称及数量：自动旋转门 1樘二、自动旋转门基本技术规格：1、工作环境及条件：温度：－20～50°C：电压：220V/50Hz。