机械方面专业术语(中英文对照)
常用机械专业术语中英文对照
常用机械专业术语中英文对照1. 强度 (Strength)1.1 抗拉强度 (Tensile Strength)抗拉强度是指材料在拉伸状态下能承受的最大应力。
通常以N/mm²或MPa来表示。
1.2 抗压强度 (Compressive Strength)抗压强度是指材料在受到压缩力作用下能承受的最大应力。
通常以N/mm²或MPa来表示。
1.3 屈服强度 (Yield Strength)屈服强度是指材料开始发生塑性变形时所受到的最大应力。
通常以N/mm²或MPa来表示。
1.4 硬度 (Hardness)硬度是材料抵抗划痕或穿刺的能力。
常用的硬度测试方法包括布氏硬度（HB）、洛氏硬度（HRC）等。
2. 刚度 (Stiffness)2.1 弹性模量 (Elastic Modulus)弹性模量是材料在受力时发生弹性变形的能力。
通常以N/mm²或GPa来表示。
对于弹性材料，弹性模量与刚度成正比。
2.2 泊松比(Poisson’s Ratio)泊松比是材料在受力时横向收缩与纵向变形之间的比例关系。
泊松比的取值范围在0到0.5之间。
2.3 弯曲刚度 (Flexural Stiffness)弯曲刚度是指材料在受到弯曲力作用下的抵抗能力。
通常以N/mm²或Nm²来表示。
3. 疲劳性能 (Fatigue Performance)3.1 疲劳寿命 (Fatigue Life)疲劳寿命是指材料在循环加载下能承受的次数或应力级别。
通常以循环次数或循环应力来表示。
3.2 疲劳极限 (Fatigue Limit)疲劳极限是指材料在循环加载下能承受的最大应力水平而不发生疲劳破坏的能力。
通常以N/mm²或MPa来表示。
3.3 疲劳强度 (Fatigue Strength)疲劳强度是指材料在循环加载下能够承受的最大应力。
通常以N/mm²或MPa来表示。
4. 可靠性 (Reliability)4.1 故障率 (Flure Rate)故障率是指单位时间内发生故障的概率。
机械方面专业术语中英文对照
机械方面专业术语(中英文对照)机械专业英语词汇（很全）金属切削metal cutting机床machine tool金属工艺学technology of metals刀具cutter摩擦friction联结link传动drive/transmission轴shaft弹性elasticity频率特性frequency characteristic误差error响应response定位allocation机床夹具jig动力学dynamic运动学kinematic静力学static分析力学analyse mechanics拉伸pulling压缩hitting剪切shear扭转twist弯曲应力bending stress强度intensity三相交流电three-phase AC磁路magnetic circles变压器transformer异步电动机asynchronous motor几何形状geometrical精度precision正弦形的sinusoid交流电路AC circuit机械加工余量machining allowance 变形力deforming force变形deformation应力stress硬度rigidity热处理heat treatment退火anneal正火normalizing脱碳decarburization渗碳carburization电路circuit半导体元件semiconductor element 反馈feedback发生器generator直流电源DC electrical source门电路gate circuit逻辑代数logic algebra外圆磨削external grinding内圆磨削internal grinding平面磨削plane grinding变速箱gearbox离合器clutch绞孔fraising绞刀reamer螺纹加工thread processing螺钉screw铣削mill铣刀milling cutter功率power工件workpiece齿轮加工gear mechining齿轮gear主运动main movement主运动方向direction of main movement进给方向direction of feed进给运动feed movement合成进给运动resultant movement of feed合成切削运动resultant movement of cutting合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth前刀面rake face刀尖nose of tool前角rake angle后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration 气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability 螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing 滑动轴承sliding bearing 弹簧spring制动器arrester brake十字结联轴节crosshead 联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor 集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC 电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model 画法几何descriptive geometry 机械仆?Mechanical drawing投影projection视图view剖视图pro标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements 刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel参考资料：回答者：Z赌神| 三级| 2006-6-8 16:15 机械专业英语词汇（很全）金属切削metal cutting机床machine tool金属工艺学technology of metals刀具cutter摩擦friction联结link传动drive/transmission轴shaft弹性elasticity频率特性frequency characteristic 误差error响应response定位allocation机床夹具jig动力学dynamic运动学kinematic静力学static分析力学analyse mechanics拉伸pulling压缩hitting剪切shear扭转twist弯曲应力bending stress强度intensity三相交流电three-phase AC磁路magnetic circles变压器transformer异步电动机asynchronous motor几何形状geometrical精度precision正弦形的sinusoid交流电路AC circuit机械加工余量machining allowance 变形力deforming force变形deformation应力stress硬度rigidity热处理heat treatment退火anneal正火normalizing脱碳decarburization渗碳carburization电路circuit半导体元件semiconductor element 反馈feedback发生器generator直流电源DC electrical source门电路gate circuit逻辑代数logic algebra外圆磨削external grinding内圆磨削internal grinding平面磨削plane grinding变速箱gearbox离合器clutch绞孔fraising绞刀reamer螺纹加工thread processing螺钉screw铣削mill铣刀milling cutter功率power工件workpiece齿轮加工gear mechining齿轮gear主运动main movement主运动方向direction of main movement 进给方向direction of feed进给运动feed movement合成进给运动resultant movementof feed合成切削运动resultant movement of cutting合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth前刀面rake face刀尖nose of tool前角rake angle后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration 气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing 滑动轴承sliding bearing 弹簧spring制动器arrester brake十字结联轴节crosshead 联轴器coupling链chain皮带strap精加工finish machining 粗加工rough machining 变速箱体gearbox casing 腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design 有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC 电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer 气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry 机械仆?Mechanical drawing投影projection视图view剖视图pro标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements 刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel参考资料：回答者：uuu | 三级| 2006-6-11 13:22机械术语中英文对照:Piping work: 铺管工程Steam trace: 加热蒸汽管道Cutting: 切割socket weld承插焊接fillet weld角焊,填角焊branch connection分支接续fabrication tolerance.制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding.密封焊接flange joint 凸缘接头undercut 底切feeder馈电线conduit outlet电线引出口seal fitting 密封接头, 密封配件Screw thread lubricant螺纹润滑剂Seal: 绝缘层weld reinforcement 焊缝补强lock washer 锁紧[止动, 防松]垫圈electrical panel.配电板,配电盘nipple螺纹接头zinc plated.镀锌的ring joint 环接, 围缘接合bolt 螺栓control: 控制器National Electrical Code 全国电气规程master schedule 主要图表, 综合图表, 设计任务书, 主要作业表torque wrench 转矩扳手job site 施工现场flange connection.凸缘联接Hard hat：安全帽Goggles：护目镜stockpile贮存packing list装箱单crate: 柳条箱purchased material list原材料进货单back-feed反馈wire coil线盘，线卷，NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫terminal block线弧, 接头排接线盒, 接线板, 线夹power drill机械钻connector. 接线器insulated sleeve绝缘套管wire connector接线器wire terminal电线接头control wiring控制线路motor lead电动机引出线power wiring电力布线tender document．提供证件orifice plate.挡板nut 螺母flange gasket 法兰垫片dimensional inspection 尺寸检验burn through 烧蚀piping system.管道系统reinforcement of weld加强焊缝fabrication.制造dye penetrant examination染料渗透试验法magnetic particle examination 磁粉检验girth weld环形焊缝cement lined piping 水泥衬里weld joint 焊缝, 焊接接头spool drawing 管路图, 管路详图spot test 抽查, 当场测试butt weld 对接焊缝Random Radiography随机射线照相检查radiographic examination 射线照相检查assembly.装配erection 架设examination试验cable tray.电缆盘rigid steel conduit 钢制电线管power control 功率控制arc welding 电弧焊control cable控制电缆操纵索normal bend 法向[法线]弯管cable glands: 电缆衬垫exfoliation剥落power receptacle 电力插座grounding conductor 接地导体lighting fixture照明器材junction box 分线箱race way 电缆管道terminal box接线盒distribution board配电盘, 配电屏receptacle 插座tumble switch.翻转开关,拨动式开关cathodic protection system 阴极保护系统Circuit breaker断路开关amplifier panel 放大器盘control console 控制台electrical material电气材料convenience receptacle.电源插座cable gland 电缆衬垫TIG：Tungsten-arc Inert-Gas welding 钨极电弧惰性气体保护焊filler rod焊条tensile strength 抗张强度shield gas 保护气体shield jig保护夹具high frequency generator.高频发电机welding rod 焊条filler metal 焊料, 焊丝shop fabrication 车间制造field installation 现场安装welding bead 焊道both sides welding.双面焊接residual stress 残余应力electrode 电焊条condensation 冷凝longitudinal.纵向的horizontal line 水平线circumferential joint 周圈接缝nondestructive examination.非破坏性检验, qualification: 合格性construction work施工工程welded joint焊接缝焊接节点gas cutting.气割arc cutting电弧切割grind off 磨掉metallic luster 金属光泽Screwed Piping Joints螺丝状的管接头gouging .刨削槽Bending: 挠曲witness test订货人在场的试验Welding: 焊接Threading: 车缧纹Leveling：校平color identification 彩色识别Alignment：对准,定位调整check against 检查, 核对Fixing：固定Console：控制台cubicle室,箱audit 审计material certificate.材料合格证vertical panel竖直面板power distribution panel 配电盘gauge board仪表板beveling 磨斜棱,磨斜边local panel 现场配电盘grouting 灌浆fabrication 加工,制造instrument rack 计测器支架tank gauge 液面计flushing 冲洗，填缝analyzer分析器piping管道敷设tubing敷设管道cable fitting电缆配件elbow.弯管接头main pipe 主管道bend.弯管弯头solvent 溶剂postweld heat treatment 焊后热处理jig.夹具arc gouging 电弧刨削chipping修琢machining 机械加工bridges.管式桥clamp.夹钳tack welding 点焊butt welding 对接焊grinder. 磨床commencement.开始gusset plate角撑板, 加固板process pipe 工艺管道land 纹间表面tee 三通管丁字钢T形梁opening 开口reinforcing pad.补强垫,增强衬板flux 焊剂wet developer 湿显像剂blowhole气泡,气孔inclusion 杂质imperfection 缺陷limitation 限度valve 阀,闸门structural attachment 结构附件tapered allowance 削尖余量tack welding 平头焊接sputter 喷溅scale 废料lateral translation侧向平移weld joint 焊缝, 焊接接头plug.塞fusion 熔融base material基底材料lead foil 铅箔intensifying screen 增光屏, 光增强屏pressure test.压力试验film density.影片密度line number行数leak test漏泄试验plate thickness 筛板厚度restoration修理field fabricated 工地制造的,现场装配的junction box.接线盒flow sheet 流程图vent 放气孔, 通风孔drain 排水管instrument air仪表气源blind挡板pipe arrangement 管配置civil engineer.土木工程师bus duct 母线槽substation分站flow instrument 流量计power distribution panel 配电盘level instrument 位面计, 水平仪pressure instrument 压力仪表/压力计level switch (信号)电平开关,gage glass 液位玻璃管pilot tube指示灯line check 小检修recalibration.复校,重新校准blinding plate盲板expansion joint 伸缩接头hydrostatic pressure test静水压试验pneumatic pressure 气压scaffolding脚手架check valve止回阀liquid penetrant examination液体渗透探伤test pump试验泵witnessed inspections 现场检测hanger吊架control valve控制阀,fabrication drawing 制造图纸,制作图schedule number表示管壁厚度系列的号码hydrostatic test .流体静力学试验,水压试验design pressure 设计压力disposition notice 处罚通知书pipe stanchion 管支柱bellow type 波纹管式expansion joint 伸缩接头vibration stopper：减震器subcontractor 转包商WPS Works Process Specification 典型工艺规程piping.管道系统flange.凸缘sleeve 套筒ferritic .铁素体的identification mark 识别标志stencil.模绘片版,镂花模板stamping .冲压silicone paint硅树脂油漆weld bead 焊缝automatic temperature recorder 温度自动记录器penetrameter 透度计film viewer底片观察用光源civil works土建工程，建筑工程lump sum price 混合价格,统包价格scrap material废料caulking metal填隙合金[金属](材料)application drawing操作图, 应用图cable routing电缆路由选择channel bases沟渠基底vertical panel竖直面板local panel 现场配电盘power distribution panel 配电盘gauge board样板, 模板规准尺anchor bolt 锚定螺栓expansion bolt 伸缩栓, 扩开螺栓field instrument.携带式仪表instrument rack 计测器支架,计测器框架tank gauge 油箱液位计guide wire 尺度[定距]索,准绳name plate名牌, 商标lead pipe铅管take-off valve输出阀sub-header分联箱air header 集气管pneumatic signal气动信号steam trace 加热蒸汽管道electric heat tracing.电伴随加热cable trunk 电缆管道stop end封端fire barriers防火间隔bonding wire 接合线, 焊线conduit box [电]导管分线匣rigid conduits 刚性导管flexible conduit软管conduit entry 导管引入装置road crossing duct bank平交道口管道组Capping ends顶盖末端cable armor电缆铠装Cable sheath电缆包皮层sealing compound电缆膏coaxial cable同轴电缆loop test环路测试sequence test.联锁顺序试验lintel beam 水平横楣梁flash plate闪熔镀层anchor bolt 地脚螺栓expansion bolt伸缩栓, 扩开螺栓shim plate 垫板push button station按钮式控制站logic diagram逻辑图calculation sheet计算书flow instrument流量计level instrument 位面计, 水平仪layout drawing 布置图tie band捆扎用带材Heating boxes加热室cutting opening切孔control valve actuator 阀控传动机构air set空气中凝固, 常温自硬自然硬化solenoid valve.螺线管阀,电磁阀calorimeter热量计odometer历程标tachometer转速计chronometer精密计时表。
机械术语中英文对照汇编
机械术语中英文对照汇编引言在机械领域中，掌握各种机械术语的中英文对照是非常重要的。
具备这样的知识可以更好地理解和沟通机械工程方面的知识。
本文将介绍一些常见的机械术语的中英文对照，以帮助读者更好地掌握这个领域。
一、机械部件及装置1.齿轮（Gear）2.轴（Shaft）3.轴承（Bearing）4.皮带（Belt）5.键槽（Keyway）6.轴套（Sleeve）7.螺母（Nut）8.螺栓（Bolt）9.泵（Pump）10.阀门（Valve）二、机械运动1.旋转（Rotation）2.平移（Translation）3.倾斜（Tilt）4.摩擦（Friction）5.惯性（Inertia）6.阻尼（Damping）7.弹簧（Spring）8.螺旋（Spiral）三、机械工艺1.钻孔（Drilling）2.铣削（Milling）3.车削（Turning）4.切削（Cutting）5.焊接（Welding）6.铆接（Riveting）7.雕刻（Engraving）8.抛光（Polishing）9.喷涂（Spraying）四、机械力学1.力（Force）2.加速度（Acceleration）3.速度（Velocity）4.质量（Mass）5.惯性力（Inertial Force）6.弹性力（Elastic Force）7.重力（Gravity）8.摩擦力（Frictional Force）9.引力（Tension）10.动量（Momentum）五、机械精度1.公差（Tolerance）2.精度（Precision）3.粗糙度（Roughness）4.轴向（Axial）5.径向（Radial）6.径向间隙（Radial Clearance）7.齿间隙（Backlash）8.平行度（Parallelism）9.垂直度（Perpendicularity）10.同心度（Concentricity）六、机械测量1.量程（Range）2.精度（Accuracy）3.分度（Resolution）4.零偏（Offset）5.示值误差（Indication Error）6.重复性（Repeatability）7.稳定性（Stability）8.灵敏度（Sensitivity）七、机械维护1.保养（Maintenance）2.润滑（Lubrication）3.换油（Oil Change）4.更换零件（Parts Replacement）5.检修（Overhaul）6.清洁（Cleaning）7.校准（Calibration）8.故障排除（Troubleshooting）结论以上是一些常见的机械术语的中英文对照。
(机械制造行业)机械专业中英文对照翻译大全
（机械制造行业）机械专业中英文对照翻译大全机械专业英语词汇中英文对照翻译一览表陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center 车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine 拉孔broaching装配assembling铸造found流体动力学fluid dynamics 流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor 集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC 电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting 相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant 逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheelAssembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed 变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross 槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism 串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes 动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics 反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism 复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism 刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment 公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design 共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling 滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation 技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions 计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturingsystem, CIMS计算力矩factored moment; calculation moment 计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism 减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair 空间运动链spatial kinematic chain 空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action 隶属度membership力force力多边形force polygon。
机械术语中英文对照
机械术语中英文对照成形不良用语a berration 色差atomization ?化bank mark ?料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料堵塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮摺叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱摺surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹模具常用刀具与工作法用语adjustable spanner 活动扳手angle cutter 角铣刀anvil 铁? arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手电脑关联用语3D modeling 三次元模拟access 通路animation 卡通影片application 应用board 基板bug 故障bus 汇流排CAD 电脑辅助设计CAE 电脑辅助工程分析CAM 电脑辅助制造cassette 卡座color display 彩色显示器command 指令communication 通信compact 精简小型computer 电脑copy 复制cursor 游标curve modeling 曲面模拟database 资料库design 设计digitizing 数位化disk 磁碟dot 点eyelet 眼孔floppy 磁碟片format 格式化graphic 圆解hardware 硬体honeycomb 蜂巢interface 界面know how 要领laser printer 雷射印表机lay out 布置memory 经历memory swap 交换经历microprocessor 微处理器modeling 造型module 模组monitor 萤幕mouse 滑鼠need 需求network 网路new version 新版on line 上线中option 选择PC 个人电脑plotter 绘图机program 程式scanning 扫描simulation 模拟software 软体solid model 实体模型system 系统tape 磁带terminal 终端机texture 构造trim 修边venter 排气风扇word processor 文书处理器各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工caulking ?合加工coining 压印加工compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 叠板裁断drawing 引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 周密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 摺叠加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting ?接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining 无废料加工seaming 折弯重叠加工shaving 缺口修整加工shearing 切断加工sizing 精压加工/矫正加工slitting 割缝加工spinning 卷边?接staking ?固stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面camlachie cramp 铸包casting on flat ?合chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调剂螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 周密下料冲床forging roll 辊锻机finishing slag 炼後熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路操纵器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置motor 马达moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全爱护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造separate 分离shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平稳器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电arc discharge 电弧放电belt 皮带centreless 无心chrome bronze 铭铜clearance angle 後角corner shear drop 直角压陷deflection 桡曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 间隙graphite 石墨graphite contraction allowance 电极缩小余量graphite holder 电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working 肋部加工roller electrode 滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂tungsten bronze ?青铜waviness 波形起伏work 工件working allowance 加工余量working dischard 加工废料。
常用机械专业术语中英文对照
常用机械专业术语中英文对照基础机构fundamental mechanism差不多额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions运算机辅助设计computer aided design, CAD运算机辅助制造computer aided manufacturing, CAM运算机集成制造系统computer integrated manufacturing system, CIMS运算力矩factored moment; calculation moment运算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism 减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向差不多额定动载荷basic dynamic radial load rating 径向差不多额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平稳static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平稳equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel联组V 带tight-up V belt联轴器coupling ; shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design ; design for environment马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评判fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion ;wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评判与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平稳balance平稳机balancing machine平稳品质balancing quality平稳平面correcting plane平稳质量balancing mass平稳重counterweight平稳转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears一般平键parallel key其他常用机构other mechanism in common use起动时期starting period启动力矩starting torque气动机构pneumatic mechanism奇特位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平稳heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham‘s coupling 矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing松边slack-side顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不平均( 波动) 系数coefficient of speed fluctuation 速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding motion弹性联轴器elastic coupling ; flexible coupling弹性套柱销联轴器rubber-cushioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form专门运动链special kinematic chain特性characteristics替代机构equivalent mechanism调剂modulation, regulation调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing调心轴承self-aligning bearing调速speed governing调速电动机adjustable speed motors调速系统speed control system调压调速variable voltage control调速器regulator, governor铁磁流体密封ferrofluid seal停车时期stopping phase停歇dwell同步带synchronous belt同步带传动synchronous belt drive凸的，凸面体convex凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling外齿轮external gear弯曲应力beading stress弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement位移曲线displacement diagram位姿pose , position and orientation稳固运转时期steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism 蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite系杆crank arm, planet carrier现场平稳field balancing向心轴承radial bearing向心力centripetal force /离心力centrifugal force相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion 修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear谐波传动harmonic driving谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism 虚拟现实virtual reality虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD虚约束redundant (or passive) constraint许用不平稳量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; permissible stress悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism一样化运动链generalized kinematic chain移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration应力图stress diagram应力—应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion 预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring 圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不平均系数coefficient of velocity fluctuation运动粘度kenematic viscosity载荷load载荷—变形曲线load—deformation curve载荷—变形图load—deformation diagram窄V 带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator 直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact周节pitch周期性速度波动periodic speed fluctuation周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load轴向差不多额定动载荷basic dynamic axial load rating轴向差不多额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair转速swiveling speed ; rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平稳balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear 锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work 纵向重合度overlap contact ratio纵坐标ordinate组合机构combined mechanism最少齿数minimum teeth number最小向径minimum radius作用力applied force坐标系coordinate frame。
机械专业术语大全
机械专业术语（英语）大全机械专业术语，中英文对照！阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation ; creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing角接触向心轴承angular contact radial bearing角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating径向基本额定静载荷basic static radial load tating 径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel 联组V 带tight-up V belt联轴器coupling ; shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design ; design for environment马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion ;wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham‘s co upling 矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint 双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing松边slack-side顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation 速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding motion弹性联轴器elastic coupling ; flexible coupling弹性套柱销联轴器rubber-cushioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form特殊运动链special kinematic chain特性characteristics替代机构equivalent mechanism调节modulation, regulation调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing调心轴承self-aligning bearing调速speed governing调速电动机adjustable speed motors调速系统speed control system调压调速variable voltage control调速器regulator, governor铁磁流体密封ferrofluid seal停车阶段stopping phase停歇dwell同步带synchronous belt同步带传动synchronous belt drive凸的，凸面体convex凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling 外齿轮external gear弯曲应力beading stress弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement位移曲线displacement diagram位姿pose , position and orientation稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite系杆crank arm, planet carrier现场平衡field balancing向心轴承radial bearing向心力centrifugal force相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion 修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear谐波传动harmonic driving谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism 虚拟现实virtual reality虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; permissible stress悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism一般化运动链generalized kinematic chain移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration应力图stress diagram应力—应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion 预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation 运动粘度kenematic viscosity载荷load载荷—变形曲线load—deformation curve载荷—变形图load—deformation diagram窄V 带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator 直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact周节pitch周期性速度波动periodic speed fluctuation周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load轴向基本额定动载荷basic dynamic axial load rating 轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair转速swiveling speed ; rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work 纵向重合度overlap contact ratio纵坐标ordinate组合机构combined mechanism最少齿数minimum teeth number最小向径minimum radius作用力applied force坐标系coordinate frame机械专利翻译词汇三千个Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. Inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试V oltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department 生产部门planning department 企划部QC Section 品管科stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂common equipment 常用设备uncoiler and straightener 整平机punching machine 冲床robot 机械手hydraulic machine 油压机lathe 车床planer 刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机staker=reviting machine 铆合机position 职务president 董事长general manager 总经理special assistant manager 特别助理factory director 厂长department director 部长deputy manager | =vice manager 副经理section supervisor 课长deputy section supervisor =vice section superisor 副课长group leader/supervisor 组长line supervisor 线长assistant manager 助理to move, to carry, to handle 搬运be put in storage 入库pack packing 包装to apply oil 擦油to file burr 锉毛刺final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料to unload material 卸料to return material/stock to 退料scraped |'skræpid| 报废scrape 刮;削deficient purchase 来料不良manufacture procedure 制造过程deficient manufacturing procedur 制造过程不良oxidation 氧化scratch 刮伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车compound die 合模die locker 锁模器pressure plate=plate pinch 压板bolt 螺栓name of a department 部门名称administration/general affairs dept 总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(or jig) 治具power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单screwdriver holder 起子插座pedal 踩踏板stopper 阻挡器。
机械专业术语中英文对照
机械专业术语中英文对照机械专业术语组装、冲压、喷漆等专业词汇 Assembly line 组装线 Layout 布置图 Conveyer 流水线物料板 Rivet table 拉钉机Rivet gun 拉钉枪 Screw driver 起子 Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌OOBA 开箱检查 fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板 barcode 条码 barcode scanner 条码扫描器 fuse together 熔合 fuse machine 热熔机 repair 修理 operator 作业员 QC 品管 supervisor 课长 ME 制造工程师 MT 制造生技 cosmetic inspect 外观检查 inner parts inspect 内部检查 thumb screw 大头螺丝 lbs. inch 镑、英寸 EMI gasket 导电条 front plate 前板 rear plate 后板 chassis 基座 bezel panel 面板 power button 电源按键 reset button 重置键 Hi-pot test of SPS 高源高压测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts 塑胶件 SOP 制造作业程序 material check list 物料检查表 work cell 工作间trolley 台车 carton 纸箱 sub-line 支线 left fork 叉车personnel resource department 人力资源部 production department 生产部门 planning department 企划部 QC Section 品管科 stamping factory 冲压厂 painting factory 烤漆厂molding factory 成型厂 mon equipment 常用设备 uncoiler and straightener 整平机 punching machine 冲床 robot 机械手hydraulic machine 油压机 lathe 车床 planer |"plein|刨床 miller 铣床 grinder 磨床 driller 钻床 linear cutting 线切割 electrical sparkle 电火花 welder 电焊机staker=reviting machine 铆合机 position 职务 president 董事长 general manager 总经理 special assistant manager 特助factory director 厂长 department director 部长 deputy manager=vice manager 副理 section supervisor 课长 deputy section supervisor 副课长 vice section superisor 副课长group leader/supervisor 组长 line supervisor 线长 assistant manager 助理 to move, to carry, to handle 搬运 be put in storage 入库 pack packing 包装 to apply oil 擦油 to file burr 锉毛刺 final inspection 终检 to connect material 接料to reverse material 翻料 wet station 沾湿台 Tiana 天那水cleaning cloth 抹布 to load material 上料 to unload material 卸料 to return material/stock to 退料 scraped |"skræpid|报废 scrape ..v.刮;削 deficient purchase 来料不良 manufacture procedure 制程 deficient manufacturing procedure制程不良 oxidation |" ksi"dein|氧化scratch 刮伤 dents 压痕 defective upsiding down 抽芽不良defective to staking 铆合不良 embedded lump 镶块 feeding is not in place 送料不到位 stamping-missing 漏冲 production capacity 生产力 education and training 教育与训练 proposal improvement 提案改善 spare parts=buffer 备件 forklift 叉车trailer=long vehicle 拖板车 pound die 合模 die locker 锁模器 pressure plate=plate pinch 压板 bolt 螺栓 name of a department 部门名称 administration/general affairs dept总务部 automatic screwdriver 电动启子 thickness gauge 厚薄规gauge(or jig)治具 power wire 电源线 buzzle 蜂鸣器 defectiveproduct label 不良标签 identifying sheet list 标示单screwdriver holder 起子插座 pedal 踩踏板 stopper 阻挡器flow board 流水板 hydraulic handjack 油压板车 forklift 叉车pallet 栈板 glove(s)手套 glove(s) with exposed fingers 割手套 thumb 大拇指 forefinger 食指 midfinger 中指 ring finger 无名指 little finger 小指 band-aid 创可贴 iudustrial alcohol 工业酒精 alcohol container 沾湿台 head of screwdriver 起子头 sweeper 扫把 mop 拖把 vaum cleaner 吸尘器 rag 抹布garbage container 灰箕 garbage can 垃圾箱 garbage bag 垃圾袋 chain 链条 jack 升降机 production line 流水线 chain 链条槽 magizer 加磁器 lamp holder 灯架 to mop the floor 拖地 to clean the floor 扫地 to clean a table 擦桌子 air pipe 气管packaging tool 打包机 packaging 打包 missing part 漏件wrong part 错件 excessive defects 过多的缺陷 critical defect 极严重缺陷 major defect 主要缺陷 minor defect 次要缺陷 not up to standard 不合规格 dimension/size is a little bigger 尺寸偏大(小) cosmetic defect 外观不良 slipped screwhead/slippery screw head 螺丝滑头 slippedscrewhead/shippery screw thread 滑手 speckle 斑点mildewed=moldy=mouldy 发霉 rust 生锈 deformation 变形burr(金属)flash(塑件)毛边 poor staking 铆合不良 excesssive gap 间隙过大 grease/oil stains 油污 inclusion 杂质 painting peel off 脏污 shrinking/shrinkage 缩水 mixed color 杂色scratch 划伤 poor processing 制程不良 poor ining part 事件不良 fold of pakaging belt 打包带折皱 painting make-up 补漆discoloration 羿色 water spots 水渍 polishing/surface processing外表处理 exposed metal/bare metal 金属裸露 lack of painting 烤漆不到位 safety 平安 quality 品质 delivery deadline 交货期 cost 本钱 engineering 工程 die repair 模修enterprise plan = enterprise expansion projects 企划 QC 品管 die worker 模工 production, to produce 生产 equipment 设备 to start a press 开机 stop/switch off a press 关机classification regulation 整顿 cleanness 清扫 conservation 清洁 culture 教养 qualified products, up-to-grade products 良品 defective products, not up-to-grade products 不良品waste 废料 board 看板 feeder 送料机 sliding rack 滑料架defective product box 不良品箱 die change 换模 to fix a die 装模 to take apart a die 拆模 to repair a die 修模 packing material 包材 basket 蝴蝶竺 plastic basket 胶筐 isolating plate baffle plate; barricade 隔板 carton box 纸箱 to pull and stretch 拉深 to put material in place, to cut material, to input 落料 to impose lines 压线 to press, pressing 压缩character die 字模 to feed, feeding 送料 transportation 运输 (be)qualfied, up to grade 合格 not up to grade, not qualified 不合格 material change, stock change 材料变更feature change 特性变更 evaluation 评估 prepare for, make preparations for 准备 parameters 参数 rotating speed, revolution 转速 manufacture management 制造管理 abnormal handling 异常处理 production unit 生产单位 lots ofproduction 生产批量 steel plate 钢板 roll material 卷料manufacture procedure 制程 operation procedure 作业流程 to revise, modify 修订 to switch over to, switch---to throw--over switching over 切换 engineering, project difficulty 工程瓶颈 stage die 工程模 automation 自动化 to stake, staking, reviting 铆合 add lubricating oil 加润滑油 shut die 架模shut height of a die 架模高度 analog-mode device 类模器 die lifter 举模器 argon welding 氩焊 vocabulary for stamping 冲压常词汇 stamping, press 冲压 punch press, dieing out press 冲床 uncoiler & strainghtener 整平机 feeder 送料机 rack, shelf, stack 料架 cylinder 油缸 robot 机械手 taker 取料机conveyer belt 输送带 transmission rack 输送架 top stop 上死点 bottom stop 下死点 one stroke 一行程 inch 寸动 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset 复位 smoothly 顺利dent 压痕 scratch 刮伤 deformation 变形 filings 铁削 todraw holes 抽孔 inquiry, search for 查寻 to stock, storage, in stock 库存 receive 领取 approval examine and verify 审核processing, to process 加工 delivery, to deliver 交货 to return delivenry to. to send delinery back to retrn ofgoods 退货 registration 登记 registration card 登记卡 to control 管制 to put forward and hand in 提报 safe stock 平安库存 aeptance = receive 验收 to notice 通知 application form for purchase 请购单 consume, consumption 消耗 to fillin 填写 abrasion 磨损 reverse angle = chamfer 倒角character die 字模 to collect, to gather 收集 failure, trouble 故障 statistics 统计 demand and supply 需求 career card 履历卡 to take apart a die 卸下模具 to load a die 装上模具 to tight a bolt 拧紧螺栓 to looser a bolt 拧松螺栓 to move away a die plate 移走模板 easily damaged parts 易损件standard parts 标准件 breaking.(be)broken,(be)cracked 断裂to lubricate 润滑 mon vocabulary for die engineering 模具工程常用词汇 die 模具 figure file, chart file 图档 cutting die, blanking die 冲裁模 progressive die, follow (-on)die 连续模 pound die 复合模 punched hole 冲孔 panel board 镶块to cutedges=side cut=side scrap 切边 to bending 折弯 to pull, to stretch 拉伸 Line streching, line pulling 线拉伸engraving, to engrave 刻印 upsiding down edges 翻边 to stake 铆合 designing, to design 设计 design modification 设计变化 die block 模块 folded block 折弯块 sliding block 滑块 location pin 定位销 lifting pin 顶料销 die plate, front board 模板 padding block 垫块 stepping bar 垫条 upper die base 上模座 lower die base 下模座 upper supporting blank 上承板 upper padding plate blank 上垫板 spare dies 模具备品spring 弹簧 bolt 螺栓 document folder 文件夹 file folder 资料夹 to put file in order 资料 spare tools location 手工备品仓 first count 初盘人 first check 初盘复棹人 second count 复盘人 second check 复盘复核人 equipment 设备 waste materials 废料 work in progress product 在制品 casing = containerazation 装箱 quantity of physical invetory secondcount 复盘点数量 quantity of customs count 会计师盘,点数量the first page 第一联 filed by aounting department for reference 会计部存查 end-user/using unit(department) 使用单位 summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name 单据名称 This sheet and physical inventory list will be sent to aounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK 厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号 plate 电镀 mold 成型 material for engineering mold testing 工程试模材料 not included in physical inventory不列入盘点 sample 样品 ining material to be inspected进货待验 description 品名steel/rolled steel 钢材 material statistics sheet 物料统计明细表 meeting minutes 会议记录 meeting type 会别distribution department 分发单位 location 地点 chairman 主席 present members 出席人员 subject 主题 conclusion 结论decision items 决议事项 responsible department 负责单位pre-fixed finishing date预定完成日 approved by / checked by / prepared by 核准/审核/承办 PCE assembly production schedule sheet PCE 组装厂生产排配表 model 机锺 work order 工令 revision 版次 remark 备注 production control confirmation 生产确认checked by 初审 approved by 核准 department 部门 stock age analysis sheet 库存货龄分析表 on-hand inventory 现有库存available material 良品可使用 obsolete material 良品已呆滞to be inspected or reworked 待验或重工 total 合计 cause description 原因说明 part number/ P/N 料号 type 形态item/group/class 类别 quality 品质 prepared by 制表 notes 说明 year-end physical inventory difference analysis sheet 年终盘点差异分析表 physical inventory 盘点数量 physical count quantity 帐面数量 difference quantity 差异量 cause analysis 原因分析 raw materials 原料 materials 物料finished product 成品 semi-finished product 半成品 packing materials 包材 good product/aepted goods/ aepted parts/good parts 良品 defective product/non-good parts 不良品 disposed goods 处理品 warehouse/hub 仓库 on way location 在途仓oversea location 海外仓 spare parts physical inventory list 备品盘点清单 spare molds location 模具备品仓 skid/pallet 栈板 tox machine 自铆机 wire EDM 线割 EDM 放电机 coil stock 卷料 sheet stock 片料 tolerance 工差 score=groove 压线 cam block 滑块 pilot 导正筒 trim 剪外边 pierce 剪内边 drag form 压锻差 pocket for the punch head 挂钩槽 slug hole 废料孔feature die 公母模 expansion dwg 展开图 radius 半径shim(wedge)楔子 torch-flame cut 火焰切割 set screw 止付螺丝form block 折刀 stop pin 定位销 round pierce punch=die button 圆冲子 shape punch=die insert 异形子 stock locater block 定位块 under cut=scrap chopper 清角 active plate 活动板 baffle plate 挡块 cover plate 盖板 male die 公模 female die 母模 groove punch 压线冲子 air-cushion eject-rod 气垫顶杆 spring-box eject-plate 弹簧箱顶板 bushing block 衬套insert 入块 club car 高尔夫球车 capability 能力 parameter 参数 factor 系数 phosphate 皮膜化成 viscosity 涂料粘度alkalidipping 脱脂 main manifold 主集流脉 bezel 斜视规blanking 穿落模 dejecting 顶固模 demagization 去磁;消磁high-speed transmission 高速传递 heat dissipation 热传 rack 上料 degrease 脱脂 rinse 水洗 alkaline etch 龄咬 desmut 剥黑膜 D.I. rinse 纯水次 Chromate 铬酸处理 Anodize 阳性处理seal 封孔 revision 版次 part number/P/N 料号 good products 良品 scraped products 报放心品 defective products 不良品finished products 成品 disposed products 处理品 barcode 条码 flow chart 流程表单 assembly 组装 stamping 冲压 molding 成型 spare parts=buffer 备品 coordinate 座标 dismantle the die 折模 auxiliary fuction 辅助功能 poly-line 多义线 heater band 加热片 thermocouple 热电偶 sand blasting 喷沙 grit 砂砾 derusting machine 除锈机 degate 打浇口 dryer 烘干机induction 感应 induction light 感应光response=reaction=interaction 感应 ram 连杆 edge finder 巡边器 concave 凸 convex 凹 short 射料缺乏 nick 缺口 speck 瑕?? shine 亮班 splay 银纹 gas mark 焦痕 delamination 起鳞cold slug 冷块 blush 导色 gouge 沟槽;凿槽 satin texture 段面咬花 witness line 证示线 patent 专利 grit 沙砾granule=peuet=grain 细粒 grit maker 抽粒机 cushion 缓冲magnalium 镁铝合金 magnesium 镁金 metal plate 钣金 lathe 车mill 锉plane 刨 grind 磨 drill 铝 boring 镗 blinster 气泡 fillet 镶;嵌边 through-hole form 通孔形式 voller pin formality 滚针形式 cam driver 铡楔 shank 摸柄 crank shaft 曲柄轴augular offset 角度偏差 velocity 速度 production tempo 生产进度现状 torque 扭矩 spline=the multiple keys 花键quenching 淬火 tempering 回火 annealing 退火 carbonization 碳化 alloy 合金 tungsten high speed steel 钨高速的 moly high speed steel 钼高速的 organic solvent 有机溶剂 bracket 小磁导 liaison 联络单 volatile 挥发性 resistance 电阻 ion 离子 titrator 滴定仪 beacon 警示灯 coolant 冷却液 crusher 破碎机模具工程类 plain die 简易模 pierce die 冲孔模forming die 成型模 progressive die 连续模 gang dies 复合模shearing die 剪边模 riveting die 铆合模 pierce 冲孔 forming 成型(抽凸,冲凸) draw hole 抽孔 bending 折弯 trim 切边emboss 凸点 dome 凸圆 semi-shearing 半剪 stamp mark 冲记号deburr or coin 压毛边 punch riveting 冲压铆合 side stretch 侧冲压平 reel stretch 卷圆压平 groove 压线 blanking 下料stamp letter 冲字(料号) shearing 剪断 tick-mark nearside 正面压印 tick-mark farside 反面压印冲压名称类 extension dwg 展开图 procedure dwg 工程图 die structure dwg 模具结构图material 材质 material thickness 料片厚度 factor 系数upward 向上 downward 向下 press specification 冲床规格 die height range 适用模高 die height 闭模高度 burr 毛边 gap 间隙 weight 重量 total wt.总重量 punch wt.上模重量五金零件类inner guiding post 内导柱 inner hexagon screw 内六角螺钉dowel pin 固定销 coil spring 弹簧 lifter pin 顶料销 eq-height sleeves=spool 等高套筒 pin 销 lifter guide pin 浮升导料销 guide pin 导正销 wire spring 圆线弹簧 outer guiding post 外导柱 stop screw 止付螺丝 located pin 定位销 outer bush 外导套模板类 top plate 上托板（顶板） top block 上垫脚 punch set 上模座 punch pad 上垫板 punch holder 上夹板stripper pad 脱料背板 up stripper 上脱料板 male die 公模(凸模) feature die 公母模 female die 母模(凹模) upper plate 上模板 lower plate 下模板 die pad 下垫板 die holder 下夹板die set 下模座 bottom block 下垫脚 bottom plate 下托板(底板) stripping plate 内外打(脱料板) outer stripper 外脱料板inner stripper 内脱料板 lower stripper 下脱料板零件类punch 冲头 insert 入块(嵌入件) deburring punch 压毛边冲子groove punch 压线冲子 stamped punch 字模冲子 round punch 圆冲子 special shape punch 异形冲子 bending block 折刀 roller 滚轴 baffle plate 挡块 located block 定位块 supportingblock for location 定位支承块 air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆 trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子 ribbon punch 压筋冲子 reel-stretch punch 卷圆压平冲子 guide plate 定位板sliding block 滑块 sliding dowel block 滑块固定块 active plate 活动板 lower sliding plate 下滑块板 upper holderblock 上压块 upper mid plate 上中间板 spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆 spring-box eject-plate 弹簧箱顶板 bushing bolck 衬套 cover plate 盖板 guide pad 导料块塑件&模具相关英文 pre sion molding 压缩成型 flash mold 溢流式模具plsitive mold 挤压式模具 split mold 分割式模具 cavity 型控母模 core 模心公模 taper 锥拔 leather cloak 仿皮革 shiver 饰纹 flow mark 流痕 welding mark 溶合痕 post screw insert 螺纹套筒埋值 self tapping screw 自攻螺丝 striper plate 脱料板 piston 活塞 cylinder 汽缸套 chip 细碎物 handle mold 手持式模具移转成型用模具 encapsulation molding 低压封装成型射出成型用模具 two plate 两极式（模具） well type 蓄料井insulated runner 绝缘浇道方式 hot runner 热浇道 runner plat 浇道模块 valve gate 阀门浇口 band heater 环带状的电热器spindle 阀针 spear head 刨尖头 slag well 冷料井 cold slag 冷料渣 air vent 排气道 h=0.02~0.05mm w=3.2mm L=3~5mm welding line 熔合痕 eject pin 顶出针 knock pin 顶出销return pin 回位销反顶针 sleave 套筒 stripper plate 脱料板insert core 放置入子 runner stripper plate 浇道脱料板 guide pin 导销 eject rod (bar)（成型机）顶业捧 subzero 深冷处理three plate 三极式模具 runner system 浇道系统 stress crack 应力电裂 orientation 定向 sprue gate 射料浇口，直浇口nozzle 射嘴 sprue lock pin 料头钩销(拉料杆) slag well 冷料井 side gate 侧浇口 edge gate 侧缘浇口 tab gate 搭接浇口film gate 薄膜浇口 flash gate 闸门浇口 slit gate 缝隙浇口fan gate 扇形浇口 dish gate 因盘形浇口 H=F=1/2t~1/5tT=2.5~3.5mm diaphragm gate 隔膜浇口 ring gate 环形浇口subarine gate 潜入式浇口 tunnel gate 隧道式浇口 pin gate 针点浇口Φ0.8~1.0mm Runner less 无浇道 (sprue less)无射料管方式 long nozzle 延长喷嘴方式 sprue 浇口;溶渣品质人员名称类 QC quality control 品质管理人员 FQC final qualitycontrol 终点品质管制人员 IC in process quality control 制程中的品质管制人员 OQC output quality control 最终出货品质管制人员 IQC ining quality control 进料品质管制人员 TQC total quality control 全面质量管理 POC passage quality control 段检人员 QA quality assurance 质量保证人员 OQA output quality assurance 出货质量保证人员 QE quality engineering 品质工程人员品质保证类 FAI first article inspection 新品首件检查FAA first article assurance 首件确认 TVR tool verification report 模具确认报告 3B 3B 模具正式投产前确认 CP capability index 能力指数 CPK capability index of process 模具制程能力参数 SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查 QFD quality function deployment 品质机能展开 FMEA failure model effectiveness analysis 失效模式分析 8 disciplines 8 项回复内容 FA final audit 最後一次稽核 CAR corrective action request 改正行动要求 corrective action report 改正行动报告 FQC 运作类 AQL Aeptable Quality Level 运作类允收品质水准 S/S Sample size 抽样检验样本大小 ACC Aept 允收 REE Reject 拒收 CR Critical 极严重的 MAJ Major 主要的 MIN Minor 轻微的 AOQ Average Output Quality 平均出厂品质 AOQL Average Output QualityLevel 平均出厂品质 Q/R/S Quality/Reliability/Service 品质/可靠度效劳 MIL-STD Military-Standard 军用标准 S I-S IV Special I-Special IV 特殊抽样水准等级 P/N Part Number 料号L/N Lot Number 特采 AOD Aept On Deviation 特采 UAI Use As It 首件检查报告 FPIR First Piece Inspection Report 百万分之一 PPM Percent Per Million 批号制程统计品管专类 SPC Statistical Process Control 统计制程管制 SQC Statistical Quality Control统计品质管制 R Range 全距 AR Averary Range 全距平均值 UCL Upper Central Limit 管制上限 LCL Lower Central Limit 管制下限 MAX Maximum 最大值 MIN Minimum 最小值 GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否 DIM Dimension 尺寸 DIA Diameter 直径 FREQ Frequency 频率 N Number 样品数其它品质术语类 QCC Quality Control Circle 品质圈 QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 方案执行检查总结 ZD Zero Defect 零缺点 QI Quality Improvement 品质改善 QP Quality Policy 目标方针 TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单 LQL Limiting Quality Level 最低品质水准 RMA Return Material Audit 退料认可 QAN Quality Amelionrate Notice 品质改善活动 ADM Absolute Dimension Measuremat 全尺寸测量 QT Quality Target 品质目标 7QCTools 7 Quality Controll Tools 品管七大手法通用之件类 E Engineering Change Notes 工程变更通知(供应商) ECO Engineering Change Order 工程改动要求(客户) P ProcessChange Notice 工序改动通知 PMP Product Management Plan 生产管制方案 SIP Specification In Process 制程检验规格 SOP Standard Operation Procedure 制造作业标准 IS Inspection Specification 成品检验标准 BOM Bill Of Material 物料清单 PS Package Specification 包装标准 SPEC Specification 规格 DWG Drawing 图面系统文件类 QC Quality System 品质系统 ES Engineering Standarization 工程标准 CGOO China General PCE 龙华厂文件 H Huston (美国)休斯敦 C Compaq (美国)康伯公司 C China 中国大陆 A Assembly 组装(厂) S Stamping 冲压(厂) P Painting 烤漆(厂) I Intel 英特尔公司 T TAIWAN IWS International Workman Standard 工艺标准 ISO International Standard Organization 国际标准化组织 GS General Specification 一般规格 CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业标准 CQCA Q-Quality A-Assembly Compaq 产品在龙华组装厂品管作业标准 CQCP P-Painting Compaq 产品在龙华烤漆厂品管作业标准部类 PMC Production & Material Control 生产和物料控制 PPC Production Plan Control 生产方案控制 MC Material Control 物料控制 ME Manafacture Engineering 制造工程部 PE Project Engineering 产品工程部 A/C Aountant Dept 会计部 P/A Personal & Administration 人事行政部 DC Document Center 资料中心 QE Quality Engineering 品质工程(部) QA Quality Assurance 品质保证(处) QC Quality Control 品质管制(课) PD Product Department 生产部 LAB Labratry 实验室 IE Industrial Engineering 工业工程 R&D Research & Design 设计开发部 PPainting 烤漆(厂) A Asssembly 组装(厂) S Stamping 冲压(厂) 生产类 PCS Pieces 个(根,块等) PRS Pairs 双(对等) CTN Carton 卡通箱 PAL Pallet/skid 栈板 PO Purchasing Order 采购订单 MO Manufacture Order 生产单 D/C Date Code 生产日期码 ID/C Identification Code (供应商)识别码 SWR Special Work Request 特殊工作需求 L/N Lot Number 批号 P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造 PCE Personal Computer nclosure 个人电脑外设 PC Personal Computer 个人电脑 CPU Central Processing Unit 中央处理器 SECC SECC` 电解片SGCC SGCC 热浸镀锌材料 NHK North of Hongkong 中国大陆 PRC People"s Republic of China 中国大陆（中华人民共和国） U.S.A the United States of America 美国 A.S.A.P As Soon As Possible 尽可能快的 E-MAIL Electrical-Mail 电子邮件 N/A Not Applicable 不适用 QTY Quantity 数量 VS 以及 REV Revision 版本 JIT Just In Time 零库存 I/O Input/Output 输入/输出 OK Ok 好 NG Not Good 不行,不合格 C=0 Critical=0 极严重不允许 ESD Electry-static Discharge 静电排放 5S 希腊语 ,整顿,清扫,清洁,教养ATIN Attention 知会 CC Carbon Copy 副本复印相关人员 APP Approve 核准,认可,成认 CHK Check 确认 AM Ante Meridian 上午PM Post Meridian 下午 CD Compact Disk 光碟 CD-ROM Compact Disk Read-Only Memory 只读光碟 FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机 REF Reference CONN Connector 连接器 CAV Cavity 模穴 CAD Computer Aid Design 计算机辅助设计ASS"Y Assembly 装配,组装 MAT"S Material 材料 IC IntegratedCircuit 集成电路 T/P True Position 真位度 TYP Type 类型 WDR Weekly Delivery Requitement 周出货需求 C/T Cycle Time 制程周期 L/T Lead Time 前置时间(生产前准备时间) S/T Standard Time 标准时间 P/M Product Market 产品市场 3CComputer,Commumcation,Consumer electronic"s 消费性电子 5WIH When,Where,Who,What,Why,How to 5MMan,Machine,Material,Method,Measurement 4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证 DQA Desigh Quality Assurance 设计品质保证 MQA Manufacture Quality Assurance 制造品质保证 SSQA Sales and service Quality Assurance 销售及效劳品质保证 LRR Lot Rejeet Rate 批退率 BS Brain storming 脑力激荡 EMI Electronic Magion Inspect 高磁测试 FMI Frequency Modulatim Inspect 高频测试 B/MBoar/Molding(flat cable) C/P Connector of PC A/P Assembly SPS Switching power supply 电源箱 DT Desk Top 卧式(机箱) MT Mini-Tower 立式(机箱) DVD Digital Vedio Disk VCD Vdeio Compact Disk LCD Liquid Crystal Display CAD Computer AID Design CAM Computer AID Manufacturing CAE Computer AID Engineering ABIOS Achanced Basic in put/output system 先进的根本输入/输出系统 CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体 PDA Personal Digital Assistant 个人数字助理 IC Integrated Circuit 集成电路 ISA Industry Standard Architecture 工业标准体制结构 MCA Micro Channel Architecture 微通道结构 EISA Extended IndustryStandard Architecture 扩充的工业标准结构 SIMM Single in-line memory module 单项导通汇流组件 DIMM Dual in-line Memory Module 双项导通汇流组件 LED Light-Emitting Diode 发光二级管 FMEA Failure Mode Effectivenes 失效模式分析 W/H Wire Harness 金属线绪束集组件 F/C Flat Calle 排线 PCB Printed Circuit Board 印刷电路板 CAR Correction Action Report 改善报告 NG Not Good 不良 WPR Weekly Delivery Requirement 周出货要求 PPM Parts Per Million 百万分之一 TPM Total Production Maintenance 全面生产保养 MRP Material Requiremt Planning 物料需方案 OC Operation System 作业系统TBA To Be Design 待定,定缺 D/C Drawing Change P/P Plans & Procedune EMI Electrical-Music Industry 电子音乐工业 RFI Read Frequency Input 读频输入 MMC Maximum Material ondition MMS Maximum Material Size LMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式 aurate die casting 精密压铸 powder forming 粉末成形 calendaring molding 压延成形 powder metal forging 粉末锻造 cold chamber die casting 冷式压铸 precision forging 精密锻造 cold forging 冷锻 press forging 冲锻 pacting molding 粉末压出成形 rocking die forging 摇动锻造 pound molding 复合成形 rotary forging 回转锻造 pression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形 encapsulation molding 注入成形 sand mold casting 砂模铸造 extrusion molding 挤出成形 shell casting 壳模铸造 foam forming 泡成形sinter forging 烧结锻造 forging roll 轧锻 six sides forging 六面锻造 gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造 hot chamber die casting 热室压铸 swaging 挤锻 hotforging 热锻 transfer molding 转送成形 injection molding 射出成形 warm forging 温锻 investment casting 精密铸造matched die method 对模成形法 laminating method 被覆淋膜成形 low pressure casting 低压铸造 lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模 landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具 loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模 posite dies 复合模具manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具 electroformed mold 电铸成形模 multi-gate mold 复式浇口模具 expander die 扩径模 offswt bending die 双折冷弯模具 extrusion die 挤出模 palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模 porous mold 通气性模具 duplicated cavity plate 复板模 positive mold 全压式模具 fantail die 扇尾形模具pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具 progressive die 顺序模 gypsummold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具 prototype mold 雏形试验模具 ingot mold 钢锭模punching die 落料模 lancing die 切口模 raising(embossing) 压花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模 runless injection mold 无流道冷料模具 sectional die 对合模具 segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具 solid forging die 整体锻模 split forging die 拼合锻模 split mold 双并式模具 sprueless mold 无注道残料模具 squeezing die 挤压模stretch form die 拉伸成形模 sweeping mold 平刮铸模 swing die 振动模具 three plates mold 三片式模具 trimming die 切边模 unit mold 单元式模具 universal mold 通用模具 unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢 angular pin 角梢baffle 调节阻板 angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞 ball slider 球塞滑块 binder plate 压板 blank holder 防皱压板 blanking die 落料冲头 bolster 上下模板 bottom board 浇注底板 bolster 垫板bottom plate 下固定板 bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包 casting lug 铸耳 cavity 模穴(模仁) cavity retainer plate 模穴托板 center pin 中心梢clamping block 锁定块 coil spring 螺旋弹簧 cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓 core 心型 core pin 心型梢 cotter 开口梢 cross 十字接头 cushion pin 缓冲梢diaphragm gate 盘形浇口 die approach 模头料道 die bed 型底die block 块形模体die body 铸模座 die bush 合模衬套 die button 冲模母模 die clamper 夹模器 die fastener 模具固定用零件 die holder 母模固定板 die lip 模唇 die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck 爪牙夹头 dowel 定位梢 dowel hole 导套孔 dowel pin 合模梢 dozzle 辅助浇口 dowel pin 定位梢 draft 拔模锥度 draw bead 张力调整杆 drive bearing 传动轴承 ejection pad 顶出衬垫 ejector 脱模器 ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套 ejector pad 顶出垫 ejector pin 顶出梢 ejector plate 顶出板 ejector rod 顶出杆 ejector sleeve 顶出衬套 ejector valve 顶出阀 eye bolt 环首螺栓 filling core 椿入蕊 film gate 薄膜形浇口 finger pin 指形梢 finish machined plate 角形模板 finish machined round plate 圆形模板 fixed bolster plate 固定侧模板 flanged pin 带凸缘 flash gate 毛边形浇口 flask 上箱 floating punch 浮动冲头 gate 浇口 gate land 浇口面 gib 凹形拉紧? goose neck 鹅颈管 guide bushing 引导衬套 guide pin 导梢 guide post 引导柱 guide plate 导板 guide rail 导轨 head punch 顶?冲头 headless punch 直柄冲头 heavily tapered solid 整体模蕊盒 hose nippler 管接头 impact damper 缓冲器 injection ram 压射柱塞 inlay busher 嵌入衬套 inner plunger 内柱塞 inner punch 内冲头 insert 嵌件 insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockout bar 脱模杵 land 合模平坦面land area 合模面 leader busher 导梢衬套 lifting pin 起模顶?。
机械术语中英文对照
机械术语中英文对照机械是一个应用广泛的学科，而机械术语也因此显得格外重要。
机械术语不仅在机械领域内使用广泛，还在与机械有关的其他领域中广泛运用。
本文将为大家介绍机械术语的中英文对照，帮助读者更好地理解机械术语。
一、机械结构相关1.1 机械结构英文：Mechanical structure中文：机械结构1.2 机械零件英文：Mechanical part中文：机械零件1.3 缸体英文：Cylinder block中文：缸体1.4 活塞英文：Piston中文：活塞1.5 曲轴英文：Crankshaft中文：曲轴1.6 飞轮英文：Flywheel中文：飞轮1.7 转速英文：Rotation speed中文：转速1.8 扭矩英文：Torque中文：扭矩1.9 传动轴英文：Transmission shaft 中文：传动轴1.10 传动比英文：Transmission ratio 中文：传动比二、机械加工相关2.1 加工中心英文：Machining center中文：加工中心2.2 数控机床英文：Numerical control machine tool 中文：数控机床2.3 刀具英文：Tool中文：刀具2.4 精度英文：Accuracy中文：精度2.5 加工误差英文：Machining error中文：加工误差2.6 表面光洁度英文：Surface roughness中文：表面光洁度2.7 加工粗糙度英文：Machining roughness 中文：加工粗糙度2.8 加工硬度英文：Machining hardness 中文：加工硬度2.9 切削速度英文：Cutting speed中文：切削速度2.10 进给速度英文：Feed rate中文：进给速度三、机械控制相关3.1 控制系统英文：Control system中文：控制系统3.2 机电一体化英文：Mechatronics中文：机电一体化3.3 伺服电机英文：Servo motor中文：伺服电机3.4 步进电机英文：Stepper motor中文：步进电机3.5 编码器英文：Encoder中文：编码器3.6 控制器英文：Controller中文：控制器3.7 嵌入式系统英文：Embedded system 中文：嵌入式系统3.8 传感器英文：Sensor中文：传感器3.9 特征提取英文：Feature extraction中文：特征提取3.10 监控系统英文：Monitoring system中文：监控系统机械术语中英文对照不仅包含机械结构、机械加工和机械控制等方面，还有机械力学、流体力学、材料科学等相关方面的术语。
机械专业术语中英文对照
机械专业术语组装、冲压、喷漆等专业词汇Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板barcode 条码barcode scanner条码扫描器fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plasticparts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department人力资源部production department 生产部门planning department 企划部QCSection 品管科stamping factory冲压厂painting factory 烤漆厂molding factory 成型厂commonequipment 常用设备uncoiler andstraightener 整平机punchingmachine 冲床robot 机械手hydraulic machine 油压机lathe车床planer |'plein| 刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机staker=revitingmachine 铆合机position 职务president 董事长generalmanager 总经理sp ecialassistant manager特助factorydirector 厂长departmentdirector 部长deputymanager=vice manager 副理section supervisor 课长deputysection supervisor 副课长vicesection superisor 副课长groupleader/supervisor 组长linesupervisor 线长assistantmanager助理to move, to carry,to handle 搬运be put instorage 入库pack packing 包装to apply oil 擦油to file burr锉毛刺final inspection 终检toconnect material 接料toreverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料tounload material 卸料to returnmaterial/stock to 退料scraped|'skræpid| 报废scrape ..v 刮;肖1」deficient purchase 来料不良manufacture procedure 制程deficient manufacturingprocedure 制程不良oxidation |' ksi'dein|氧化scratch 舌U伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embedded lump 镶块feedingis not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=longvehicle 拖板车compound die 合模die locker 锁模器pressureplate=plate pinch 压板bolt 螺栓name of a dep artment 部门名称administration/generalaffairs dept 总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(orjig)治具power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单screwdriver holder 起子插座pedal 踩踏板stopper阻挡器flow board 流水板hydraulichandjack 油压板车forklift 叉车pallet 栈板glove(s)手套glove(s) with exposed fingers割手套thumb 大拇指forefinger 食指midfinger 中指ring finger 无名指littlefinger 小指band-aid 创可贴iudustrial alcohol 工业酒精alcohol container 沾湿台head of screwdriver 起子头sweeper 扫把mop 拖把vaccum cleaner 吸尘器rag 抹布garbage container 灰箕garbagecan 垃圾箱garbage bag 垃圾袋chain 链条jack 升降机production line 流水线chain 链条槽magnetizer 加磁器lampholder 灯架to mop the floor 拖地to clean the floor 扫地toclean a table 擦桌子air pipe气管packaging tool 打包机packaging 打包missing part 漏件wrong part 错件excessive defects 过多的缺陷critical defect 极严重缺陷major defect 主要缺陷minor defect 次要缺陷not up tostandard 不合规格dimension/size is a littlebigger 尺寸偏大（小）cosmetic defect 外观不良slipped screwhead/slipperyscrew head螺丝滑头slipped screwhead/shippery screw thread 滑手speckle 斑点mildewed=moldy=mouldy 发霉rust 生锈deformation 变形burr（金属）flash（塑件）毛边poor staking 铆合不良excesssive gap 间隙过大grease/oil stains 油污inclusion 杂质painting peeloff 脏污shrinking/shrinkage 缩水mixed color 杂色scratch 划伤poor processing 制程不良poor incoming part 事件不良fold of pakaging belt 打包带折皱painting make-up 补漆discoloration 羿色water spots 水渍polishing/surface processing 表面处理exposed metal/bare metal 金属裸露lack of painting 烤漆不到位safety 安全quality 品质delivery deadline 交货期cost成本engineering 工程die repair 模修enterprise plan = enterpriseexpansion projects 企划QC 品管die worker 模工production, toproduce 生产equipment 设备to start a p ress 开机stop/switch off a press 关机classification 整理regulation 整顿cleanness 清扫conservation 清洁culture 教养qualified products, up-to-grade products 良品defective products, not up-to-grade products 不良品waste 废料board 看板feeder送料机sliding rack 滑料架defective product box 不良品箱die change 换模to fix a die 装模to take apart a die 拆模torepair a die 修模packingmaterial 包材basket蝴蝶竺plastic basket 胶筐isolatingplate baffle plate; barricade隔板carton box 纸箱to pull and stretch 拉深to putmaterial in place, tomaterial, to input 落料toimpose lines 压线to compress,compressing 压缩character die字模to feed, feeding 送料transportation 运输（be）qualfied, up to grade 合格notup to grade, not qualified 不合格material change, stock change材料变更feature change 特性变更evaluation 评估prepare for, makepreparations for 准备parameters 参数rotating speed,revolution 转速manufacturemanagement 制造管理abnormalhandling 异常处理productionunit 生产单位lots ofproduction 生产批量steel plate 钢板roll material 卷料manufacture procedure 制程operation procedure 作业流程torevise, modify 修订to switchover to, switch---to throw--over switching over 切换engineering, projectdifficulty 工程瓶颈stage die 工程模automation 自动化to stake, staking,reviting 铆合add lubricatingoil 加润滑油shut die 架模shut height of a die 架模高度analog-mode device 类模器dielifter 举模器argon welding 氩焊vocabulary for stamping 冲压常词汇sta mpi ng, p ress 冲压pu nchp ress, dieing out p ress 冲床uncoiler & strainghtener 整平机feeder 送料机rack, shelf,stack 料架cylinder 油缸robot机械手taker 取料机conveyerbelt 输送带transmission rack输送架top stop 上死点bottomstop 下死点one stroke 一行程inch 寸动to continue, cont. 连动to grip（material）吸料location lump, locating piece,block stop 定位块reset 复位smoothly 顺利dent 压痕scratch刮伤deformation 变形filings 铁削to draw holes 抽孔inquiry,search for 查寻to stock,storage, in stock 库存receive领取approval examine andverify 审核processing, toprocess 加工delivery, todeliver 交货to returndelivenry to.to send delinery back toretrn of goods 退货registration 登记registrationcard 登记卡to control 管制toput forward and hand in 提报safe stock 安全库存acceptance = receive 验收to notice 通知application form for purchase请购单consume, consumption 消耗tofill in 填写abrasion 磨损reverse angle = chamfer 倒角character die 字模to collect,to gather 收集cut。
机械名词英译汉大全
机械名词英译汉大全机械行业是一个广泛的领域，其中包含了许多特定的名词和术语。
了解这些名词的英文翻译对于学习机械工程和通信非常重要。
本文将带您了解机械名词英译汉的大全，让您更好地掌握机械工程领域的专业术语。
A•Acceleration: 加速度•Actuator:执行器•Angular velocity: 角速度•Automation:自动化•Axis:轴B•Bearing:轴承•Bevel gear:锥齿轮•Bolt:螺栓•Bore:孔径•Bushing:套筒C•Cam:凸轮•Carrier:承载体•Clutch:离合器•Crankshaft:曲轴•Cylinder:气缸D•Deflection:挠曲•Die:模具•Drive:驱动•Dynamic:动态的E•Efficiency:效率•Elasticity:弹性•Encoder:编码器•Engine:发动机F•Fastener:紧固件•Fatigue:疲劳•Friction:摩擦•Fuel:燃料G•Gear:齿轮•Generator:发电机•Grinder:砂轮•Guide:导轨H•Heat exchanger:换热器•Hydraulic:液压的•Hose:软管•Hub:轮毂I•Idle:空闲的•Inertia:惯性•Inlet:进口•Implement:工具•Jack:千斤顶•Joint:接头•Junction:连接点•Jig:夹具K•Key:键•Kinematics:运动学•Knurling:滚花L•Laser:激光•Lever:杠杆•Lubricant:润滑剂•Lathe:车床•Machine:机器•Machining:加工•Maintenance:维护•Martensite:马氏体N•Nozzle:喷嘴•Newton:牛顿•Nonferrous:有色的•Nylon:尼龙O•Orifice:孔隙•Outlet:出口•Overload:过载P•Piston:活塞•Pulley:滑轮•Pressure:压力•Pneumatic:气动的Q•Quenching:淬火•Quick-release:快速释放•Quill:芯轴•Queue:队列R•Reducer:减速器•Reliability:可靠性•Rivet:铆钉S•Shaft:轴•Screw:螺丝•Spring:弹簧•Static:静态的T•Torque:力矩•Tolerance:公差•Thread:螺纹•Turbine:涡轮机U•Ultrasonic:超声的•Upset:擴頭•Uniform:均匀的•U-bolt:U形螺栓V•Velocity:速度•Valve:阀门•Vibration:振动•Vacuum:真空W•Welder:焊工•Worm gear:蜗杆齿轮•Welding:焊接•Wear:磨损X•X-axis:X轴•Xenon:氙气•X-ray:X射线•Xerography:静电复印Y•Yoke:夹具•Y-axis:Y轴•Yield strength:屈服强度•Yarn:纱线Z•Z-axis:Z轴•Zinc:锌•Zero clearance:零间隙•Zone:区域以上是机械名词英译汉大全，包含了机械工程领域中常见的名词和术语。
机械类专业词汇中英文对照翻译表大全
机械类专业词汇中英文对照翻译表大全机械类专业词汇表一画一字螺丝批 slot type screwdriver一点透视 one-point perspective二画二合一黏合剂 epoxy resin adhesive二合胶；混合胶 epoxy glue二维的；平面的 two-dimensional二进制 binary二极管；整流子 diode二号螺丝攻 second tap二路开关 two-way switch十进制的；公制的 metric人工制品 artefact人造板 man-made board人体工程学 ergonomics; human engineering人体尺寸 human dimension人体测量学 anthropometry; anthropometrics刀片 blade刀身 blade刀具 tool刀具溜座 carriage刀柱 tool post刀架 tool rest刀架底座 tool rest bracket刀座帷；床鞍 apron刀座鞍；溜板座 saddle力 force力三角形 triangle of force力平行四边形 parallelogram of force 力多边形；多边形力学 polygon of force 力的分解 force resolution力架；亮漆 lacquer力矩 moment力偶 couple力矩定律 law of moment力-距离图表 force-distance graph力图 force diagram力线 line of force力点 effort十字榫 cross halving joint十字螺丝 Philip's head screw十字螺丝批 Philip's type screwdriver 丁字尺；T 尺 tee square三画三爪夹头 three-jaw chuck三角尺 set square三角形结构系杆 triangulation tie三角锉 triangular file三维的；立体的 three-dimensional三氯甲烷；哥罗芳 chloroform三聚氰?胺；蜜胺 melamine三点透视 three-point perspective上油漆 painting上釉 enamelling凡立水 varnish叉形顶尖 fork centre口罩 mask士力；虫漆 shellac士巴拿；扳手 spanner大芯夹板；宽条芯夹板 blockboard; solid corestock-laminated board大量制造 mass production子口刨；槽口刨；边刨 rebate plane小型平槽刨 miniature router plane小型线料弯曲器 small wire bender小型弯折机 mini bender小型电路断路器；跳菲 miniature circuit breaker (MCB)小齿轮 pinion山樟 San Cheong工件 workpiece工字梁 I beam工作面 working surface工作图；制作图 working drawing工作台 bench; working table工具 tool工具贮存室 tool storage工具槽 well工具钢 tool steel工场 workshop工场安全 workshop safety工程字书写技巧 lettering工程系统 engineering system工程绘图 engineering drawing工业酒精；火酒 methylated spirit弓形手钻；手摇曲柄钻 brace弓形手钻嘴 brace bit弓锯 bow saw; hacksaw弓锯片 hacksaw blade弓锯床 hacksawing machine四画不平衡 imbalance不含铁金属；非铁金属 non-ferrous metal不贯穿孔；闭孔；盲孔 blind hole不贯穿鸠尾榫 lapped dovetail joint不对称 asymmetry不锈钢 stainless steel不稳定平衡 unstable equilibrium中心 centre中心线 centre line中心冲 centre punch中心钻 centre drill中心钻嘴 centre bit中央处理器 central processing unit (CPU)中性 neutral中性平衡；随遇平衡 neutral equilibrium中性轴 neutral axis中密度纤维板 medium density fibre board (MDF) 中粗锉纹 second cut中碳钢 medium carbon steel中线 neutral wire互补金属氧化物半导体 complementary metal oxide semiconductors (CMOS)介子；垫片 washer介指铁 ring mandrel介电常数；电容率 permittivity介稳态的；亚稳态的 metastable内力 internal force内卡尺 inside calipers内能 internal energy内涵性质 intensive properties内圆弯凿 scribing gouge内锁式配件 interlocking fitting内燃机 internal combustion engine内螺纹制造法 tapping内螺丝 internal thread内弯边 concave edge六角金属枝 hexagonal bar六角匙 Allen key六角头螺丝 hexagonal head screw公制的；十进制的 metric公差 tolerance冗余构件 redundant member分力 component force分子 molecule分子力 molecular force分切；分割；切断 parting off分贝 decibel分析 analysis分析及批判学 analytical and critical studies 分析器 analyzer分流器 shunt分界面；界面；接口 interface分厘卡 micrometer分规 divider分割车刀架 parting tool holder分解 decomposition分压器 potential divider; voltage divider隔离开关 isolating switch切削工具 cutting tool切削液 cutting fluid切削深度 depth of cut切屑；碎屑 chip切线锯法 tangential sawing切辊纹；滚纹 knurling切断；分切；分割 parting off 切断工具 parting tool勾；勾脚 hook勾刀；胶片?刀 plastic cutter 化胶水 tensol反向偏压 reverse biased反相放大器 inverting amplifier 反相器 inverter反射 reflection反电动势 back e.m.f.反馈；回输 feedback天拿水；稀释剂 thinner天梯牙；齿条 gear rack天然木材 natural timber天然干燥法 air seasoning孔隙率 porosity尺寸 dimension尺寸线 dimension line尺身 blade引力；重力 gravitational force 心形凸轮 heart-shaped cam心材 heartwood心轴 mandrel心销 core pin手工具 hand tool手工锯 junior hacksaw手削法 paring手持虎钳 hand vice手柄 handle手套 gloves手扫漆 brushing lacquer手推车 barrow手提式竖线锯 portable jigsaw手提电动工具 portable power tool 手提电钻 electric hand drill手进给 hand feed手摇曲柄钻；弓形手钻 brace手摇钻 hand drill手锉 hand file手锯；板锯 handsaw手锥 bradawl手辘轧机 hand rolling machine支柱；支撑物 strut支架；支座 support支点 fulcrum; pivot文字 text方向 direction方向针 pointing needle方枝 square bar方波形 square waveform方波产生器 squarer方型牙板 rectangular die方格纸；网格纸 grid paper方通 square tube方块图 block diagram方锉 square file方头钻嘴 square shank bit方螺帽 square nut方边凿；直边凿 firmer chisel木 wood木工 woodwork木工工作间 woodwork area木工工作台 woodworker's bench木工车床 wood turning lathe; woodworking lathe木工铅笔 carpenter's pencil木工刨床 thicknessing and planning machine木牙螺丝；木螺钉 wood screw木材 timber木材车削 wood turning木材车削工具 wood turning tools木屑压合板；万花板 chipboard木条接榫 corner strip joint木圆头槌 doming mallet木模；模型 patterns木线 wood strip木胶粉 ureaformal dehyde resin glue木锉 rasp木螺钉；木牙螺丝 wood screw木槌 mallet止推轴承 thrust bearing止推垫圈 thrust washer比例 proportion比例尺 scale比例常数 proportionality constant比例极限 proportional limit比较器 comparator比热容量 specific heat capacity水平投影面 horizontal plane水平仪；平水尺 spirit level水气掣；漏电断路掣 earth leakage circuit breaker (ELCB) 水晶胶；聚酯树脂 polyester resin水晶胶的铸造成形 resin casting水磨砂纸 silicon carbide paper火叉 firing fork火水；煤油 kerosene火牛；变压器 transformer火石轮 grinder火花电蚀法；放电极加工 electrical discharge machining火酒；工业酒精 methylated spirit火钳 tongs火线；活线 live wire火砖 fire brick爪扣；爪形离合器；犬齿式离合器 dog clutch牙板；丝模 die牙板扳手；丝模扳手 die holder (stock)牙板螺帽 die nuts牛皮胶；动物胶 animal glue牛油纸 tracing paper牛顿运动定律 Newton's laws of motion犬齿式离合器；爪扣；爪形离合器 dog clutch五画丙烯?丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS) 主轴；心轴 spindle主题 motif令(纸张的计数单位) ream凹座 recess凹模 hollowing block凸缘 flange凸缘联轴节 flange coupling凸轮 cam凸轮式配件 cam-action fitting凸轮传动 cam drive凸头螺丝 raised head screw加成作业；添加法 addition process加油 oiling加速器 accelerator功能；用途 function功率因子 power factor功率放大器 power amplifier功率板 power amplifier board功率晶体管 power transistor包氏记号法 Bow's notation「包浩思」；「包豪斯」〈设计风格) Bauhaus半永固法；半永久接合 semi-permanent joining 半接榫 halving joint半闭式槽榫 stopped housing joint半圆(木)锉 half-round rasp半圆车刀 turning gouge半圆锉 half-round file半圆头铆钉 snap rivet半导体 semiconductor卡路里；卡(热量单位) calorie卡纸 card paper卡尺；测径器 calipers去角；倒角 chamfer可切削性 machinability可行性 feasibility可逆过程 reversible process可压缩性 compressibility可变电阻 variable resistor四分仪 quadrant四爪夹头 four-jaw independent chuck四圆心法(绘图) four-centre method外卡尺 outside calipers外形塑造 shaping外形线；轮廓线 outline外推法 extrapolation外圆弯凿 firmer gouge外螺纹 external thread外螺纹制造法 threading外弯边 convex edge外观 appearance失真 distortion尼龙；聚醯胺 nylon; polyamide (PA)尼龙墨水针笔 technical felt-tip pen左右调校杆 lateral adjusting level市售尺寸；标准尺寸 stock size市电频率；电源频率 mains frequency平(木)锉 flat rasp平水尺；水平仪 spirit level平行投影 parallel projection平行车削 parallel turning平行虎钳 parallel vice平行钉法 parallel nailing平底弯刨 flat faced spokeshave平底钻嘴 forstner bit平板结构 slab construction平流扼流圈；滤波扼流器 smoothing choke平流电容器；滤波电容器 smoothing capacitor 平流电路；滤汳电路 smoothing circuit平面板；正台 surface plate平面图；俯视图 plan平面锤 flatter平移 translation平搭榫 corner halving joint平嘴钳 flat nose pliers平槽刨 router plane平衡 balance; equilibrium平衡力 equilibrant平衡条件 equilibrium condition平衡电桥 balanced bridge平头弧刀 square nose gouge幼纹 smooth cut打凹成形 hollowing打凸成形 raising打槽机 routing machine打线；打槽 routing打磨 fitting; polishing打磨机 polisher本生灯 Bunsen burner本征半导体 intrinsic semiconductor 正反器；触发器；复振器 flip-flop 正反馈；正回输 positive feedback 正火 normalizing正向偏置 forward bias正投影 orthographic projection正投影图 orthographic drawing正弦波形 sinusoidal waveform正面投影 front projection正视图 elevation; front elevation 正极；阳极 anode正齿轮 spur gear正台；平面板 surface plate永久性接合 permanent joining瓦通纸；瓦楞纸板 corrugated board生长层 cambium layer生产图 production drawing生胶浆 rubber cement生钢；铸钢 cast steel生铁；铸铁 cast iron用途；功能 function白杨木 poplar白胶浆 PVA glue; white glue皮沙垫 leather sandbag皮革 leather皮革黏合剂 leather glue皮鞋 leather shoes目录 contents矢量；向量 vector石灰岩 limestone石英晶体振荡器 quartz crystal oscillator石棉 asbestos; asbestus石膏 Plaster of Paris示波器 oscilloscope立体图 pictorial drawing六画交流电流 alternating current (a.c.)交流电压 a.c. voltage交联结构 cross-linked structure仿饰金 gilding metal伏特 volt光力架 clear lacquer光拉软钢 bright drawn mild steel (B.D.M.S.) 光敏电阻 light dependent resistor (LDR)光测弹性学 photoelasticity光刨；滑刨 smoothing plane光电效应 photoelectric effect光泽 lustre全闭式槽榫 closed housing joint共面力 coplanar force共聚合作用 co-polymerization共聚物 copolymer共价键 covalent bond共振；共鸣；谐振 resonance印刷电路板 printed circuit board (PCB)同素异形 allotropy同轴电缆 coaxial cable同温 equality of temperature向量；矢量 vector向量和 vector sum104合力 resultant force合口扁钳 close mouth tongs合成色；等和色 secondary colour合成品 composite合成粅料 composite material合金 alloy合金工具钢 alloy tool steel合钉；定位销 dowel回火 tempering回复力 restoring force回复力偶 restoring couple回弹 resilience回输；反馈 feedback地线 earth wire多刃切削刀具 multi-point cutter多孔塑料；泡沫塑料；海绵状塑料 foam plastics多方榫接合 pinned joint多媒体 multi-media多晶性 polycrystallinity多谐振动器；多谐振荡器 multivibrator 多边形力学；力多边形 polygon of force 字母冲 letter punch字板 letter stencil安全 safety安全守则 safety rule安全系数 safety factor安全措施 safety precaution105安全眼罩 safety goggle安全设备 safety equipment安全药箱 safety box安培 ampere安培计；电流表 ammeter尖脚 spur年轮 annual ring成本 cost成形 forming扣件；击固件 fastener扣钉 clout nail; cramp托架 bracket收缩 shrinkage曲柄 crank曲柄轴 crank shaft曲线规；云板；云尺 French curve有效的 efficient有效电流 effective current灰；灰末 ash百折胶；百折胶；聚丙烯 polypropylene (PP) 竹 bamboo羊角锤 claw hammer老化 ageing肋条 rib肌理；质感；质地 texture自由度 degree of freedom自动控制 automatic control106自动进给 auto-feed自然干燥法 natural seasoning自感量 self-inductance自感应 self-induction色彩；颜色 colour色调 tone色环 colour wheel行星齿轮；周转齿轮 epicyclic gear七画肘节开关 toggle-switch串激电动机；串绕电动机 series-wound motor 位能；势能 potential energy位梯度；势梯度 potential gradient位移 displacement位错 dislocation伸长度 elongation作工硬化 work hardening作功 work done作图线 construction line低密聚乙烯 low density polyethylene (LDPE) 低通滤波器 low-pass filter低电压 low voltage低碳钢 low carbon steel布置 layout免油轴承 oil-less bearing冷加工；冷作工 cold working冷加工硬化 cold work hardening冷色 cool colour冷轧压 cold rolling冷却系统 cooling system冷却效应 cooling effect冷却液流量 coolant rate冷凝胶；环氧树脂 epoxy resin108利口；「披」口；铁屑 burr刨平 planing刨花板；碎料板 particle board吹风机 air blower吹气模塑；吹模塑 blow moulding吹管 blow pipe含铁金属 ferrous metal含水量 moisture content坑凿 cross-cut chisel均方根值 root mean square value均角投影图；等角投影图 isometric drawing 均速圆周运动 uniform circular motion 夹；夹钳 clamp夹 cramp夹卡 mounting board夹具 fixture; jig夹具及固定装置 jig and fixture夹板；胶合板 plywood夹持工具 clamping device; holding tool夹背锯；榫锯 tenon saw夹头 chuck夹头开启匙；夹头扳手 chuck key夹叠黏合成形 lamination尾座 tailstock床身；床道 lathe bed床鞍；刀座帷 apron形心；面心 centroid109形状 shape形变 deformation「快把」板；硬质纤维板 hardboard快速移位 rapid traverse抗扭强度 torsional strength抗屈强度 bending strength; yield strength 抗性分量；无功分量 reactive component抗拉强度 tensile strength抗氧化剂 anti-oxidant抗剪强度 shearing strength抗磁性物料 diamagnetic material抗挠性 stiffness抗压强度 compressive strength抗断强度 breaking strength技术员；技师 technician扶架 steady扭力 torsion扭矩；转矩 torque扭转 torsion扭转角 angle of torsion把手 hand grip扼流圈 choke扳手 spanner; wrench投影 projection投影面 projection plane投影线 projection line攻丝 tap材料 material材料单；材料表 material list杜拉铝 duralumin杉木 spruce步进电动机 stepper motor步冲轮廓法 nibbling每分钟转数 revolution per minute (r.p.m.) 系统组件 system component角托架 angle bracket角位移 angular displacement角板；直角板 angle plate角度 angle角榫 corner angle joint; corner joint角铁 angle iron谷巴凡立水 cobal varnish车刀架 tool holder车床 lathe车床工具 lathe tools车床中心钻咀 lathe centre bit车床操作法 lathe operation车削；车旋 lathe turning; turning车削工具 turning tools防火胶板 Formica防锈 rust prevention防声耳筒；护耳器 ear-protector防松螺帽 lock nut防护装置；保护罩；保护网 guard; safety guard八画注射成形法；喷射铸造法 injection moulding并激电动机；并绕电动机 shunt-wound motor乳酪胶 casein glue乳胶漆 emulsion paint亚加力；压克力；聚甲基丙烯酸甲脂 acrylics; polymethyl methacrylate (PMMA)亚稳态的；介稳态的 metastable来回摆动 oscillating两点透视 two-point perspective刻度；划线 ruling刺冲 dot punch刮刀 scraper刮擦 scraping制动鼓 drum brake制动碟 disc brake制动器 brake受迫振动 forced vibration受迫振荡 forced oscillation和谐 harmony周转齿轮；行星齿轮 epicyclic gear固定夹；台夹 bench holdfast固定负载 dead load定子 stator定位销；合钉 dowel定位螺丝 set screw定距轮 stitch marker屈片机 folding machine屈曲 bending屈服点；降服点 yield point屈圈法 loop forming屈卷法 scrolling屈接缝 folded lap seam屈喉机 tube bender屈折 folding屈折线 folding line屈压接缝 folded & grooved seam延性 ductility延性的 ductile弦锯法 plain sawing弧口凿；圆凿 gouge往复式运动 reciprocatory motion拉力 tensile force拉力计；张力计 tensiometer; tensometer拉钉 blind rivet; pop rivet拉钉接合 blind riveting; pop riveting拉钉钳 blind riveting pliers; pop riveting pliers 拉张 tension拉张应力 tensile stress拉张应变 tensile strain拉细 drawing-down拉制法 drawing拉线 wire drawing「披」口；利口；铁屑 burr拔钳 nippers拋光 buffing拋光机 buffing machine放大；扩大 enlargement放大尺 pantograph放大倍数 amplification factor放大器 amplifier放电极加工；火花电蚀法 electrical discharge machining 易用万能尺 line setter易碎 fragile〈绘画的〉明暗运用；描影 shading枝；杆 rod杯形顶尖 cup centre杯头螺丝 hexagonal socket head cap screw板锯 panel saw松木 pine松节水 turpentine法式磨光 French polishing法拉〈电容量单位〉 farad油石；磨刀石 oil stone油漆；涂料 paint泡沫塑料；多孔塑料；海绵状塑料 foam plastics物理特性 physical property物理属性 physical attribute物理量 physical quantity盲孔；闭孔；不贯穿孔 blind hole直尺 ruler; straight rule直角叉榫 corner bridle joint直角尺 try square直角板；角板 angle plate直角杠杆 bell crank lever直身钻嘴 straight shank drill直车刀架 straight tool holder直流发电机 d.c. generator直流电流 direct current (d.c.)直流电动机；直流马达 d.c. motor直纹锯 rip saw直线切削 linear interpolation直线运动 rectilinear motion直边凿；方边凿 firmer chisel直铁剪 straight snips硅 silicon空行程 idle stroke空气动力学 aerodynamics空间 space空载 no load花纹凿 embossing stamp花梨木 rosewood花样；图案 pattern虎克定律 Hooke's Law虎钳 vice虎钳护罩 vice clamp初步意念 proposed solution表面 surface表面展开图 surface development表面张力 surface tension表面处理 surface finishing; surface treatment 表面硬化 case hardening表面硬化钢 case-hardened steel表达方式 presentation表达技巧；传意技巧 communication technique表观膨胀；视膨胀 apparent expansion金工 metalwork金工工作间 metalwork area金工角尺 engineering square金工车床 metalwork lathe金工虎钳 engineer's vice金工锯床 power hacksaw金属包头；金属箍 ferrule金属配件 metal fittings金属线 wire金属压展机 hand rolling mill金属擦光剂；磨光剂 metal polish金属薄片 sheet metal金属键 metallic bond长方通 rectangular tube长刨 trying plane长螺旋钻咀 long auger bit长镗孔 long boring闸极 gate阻抗 impedance附件 attachment附录 appendices青铜 bronze非反相放大器 non-inverting amplifier非本征半导体 extrinsic semiconductor非破坏性试验 non-destructive testing非晶状固体 amorphous solid非顽磁性铁磁材料 non-retentive ferromagnetic material 非压缩性流体 incompressible fluid非稳态 unsteady state非铁金属；不含铁金属 non-ferrous metal九画亮漆；力架 lacquer信号 signal信号产生机 signal generator信号处理 signal processing保养；维修 maintenance保险丝 fuse保护罩；保护网；防护装置 guard; safety guard促凝剂 accelerator削屑 swarf垂直投影面 vertical plane型砧 swages〈书的〉封皮 binding封面 cover急回机构 quick return mechanism 扁枝 bar扁头 cross-pein扁头法 upsetting扁头铆钉 flat head rivet扁头螺丝 flat head screw扁凿 flat chisel指示器 indicator指形榫 finger joint施力 effort染色 staining染色剂 stain架构 framework柄 stock柚木 teak柳安木 lauan。
机械术语中英文对照
机械术语中英文对照Bending: 挠曲witness test订货人在场的试验Welding: 焊接Threading: 车缧纹Leveling：校平color identification 彩色识别Alignment：对准,定位调整check against 检查, 核对Fixing：固定Console：控制台cubicle室,箱audit 审计material certificate.材料合格证vertical panel竖直面板power distribution panel 配电盘gauge board仪表板beveling 磨斜棱,磨斜边local panel 现场配电盘grouting 灌浆fabrication 加工,制造instrument rack 计测器支架tank gauge 液面计flushing 冲洗，填缝analyzer分析器piping管道敷设tubing敷设管道cable fitting电缆配件elbow.弯管接头main pipe 主管道bend.弯管弯头solvent 溶剂postweld heat treatment 焊后热处理jig.夹具arc gouging 电弧刨削chipping修琢machining 机械加工bridges.管式桥clamp.夹钳tack welding 点焊butt welding 对接焊grinder. 磨床commencement.开始gusset plate角撑板, 加固板process pipe 工艺管道land 纹间表面tee 三通管丁字钢 T形梁opening 开口reinforcing pad.补强垫,增强衬板flux 焊剂wet developer 湿显像剂blowhole气泡,气孔inclusion 杂质imperfection 缺陷limitation 限度valve 阀,闸门structural attachment 结构附件tapered allowance 削尖余量tack welding 平头焊接sputter 喷溅scale 废料lateral translation侧向平移weld joint 焊缝, 焊接接头plug.塞fusion 熔融base material基底材料lead foil 铅箔intensifying screen 增光屏, 光增强屏pressure test.压力试验film density.影片密度line number行数leak test漏泄试验plate thickness 筛板厚度restoration修理field fabricated 工地制造的,现场装配的junction box.接线盒flow sheet 流程图vent 放气孔, 通风孔drain 排水管instrument air仪表气源blind挡板pipe arrangement 管配置civil engineer.土木工程师bus duct 母线槽substation分站flow instrument 流量计power distribution panel 配电盘level instrument 位面计, 水平仪pressure instrument 压力仪表/压力计level switch (信号)电平开关,gage glass 液位玻璃管pilot tube指示灯line check 小检修recalibration.复校,重新校准blinding plate盲板expansion joint 伸缩接头hydrostatic pressure test静水压试验pneumatic pressure 气压scaffolding脚手架check valve止回阀liquid penetrant examination液体渗透探伤test pump试验泵witnessed inspections 现场检测hanger吊架control valve控制阀,fabrication drawing 制造图纸,制作图schedule number表示管壁厚度系列的号码hydrostatic test .流体静力学试验,水压试验design pressure 设计压力disposition notice 处罚通知书pipe stanchion 管支柱bellow type 波纹管式expansion joint 伸缩接头vibration stopper：减震器subcontractor 转包商WPS Works Process Specification 典型工艺规程piping.管道系统flange.凸缘sleeve 套筒ferritic .铁素体的identification mark 识别标志stencil.模绘片版,镂花模板stamping .冲压silicone paint硅树脂油漆weld bead 焊缝automatic temperature recorder 温度自动记录器penetrameter 透度计film viewer底片观察用光源civil works土建工程，建筑工程lump sum price 混合价格 ,统包价格scrap material废料caulking metal填隙合金[金属](材料) application drawing操作图, 应用图cable routing电缆路由选择channel bases沟渠基底vertical panel竖直面板local panel 现场配电盘power distribution panel 配电盘gauge board样板, 模板规准尺anchor bolt 锚定螺栓expansion bolt 伸缩栓, 扩开螺栓field instrument.携带式仪表instrument rack 计测器支架,计测器框架tank gauge 油箱液位计guide wire 尺度[定距]索,准绳name plate名牌, 商标lead pipe铅管take-off valve输出阀sub-header分联箱air header 集气管pneumatic signal气动信号steam trace 加热蒸汽管道electric heat tracing.电伴随加热cable trunk 电缆管道stop end封端fire barriers防火间隔bonding wire 接合线, 焊线conduit box [电]导管分线匣rigid conduits 刚性导管flexible conduit软管conduit entry 导管引入装置road crossing duct bank平交道口管道组Capping ends顶盖末端cable armor电缆铠装Cable sheath电缆包皮层sealing compound电缆膏coaxial cable同轴电缆loop test环路测试sequence test.联锁顺序试验lintel beam 水平横楣梁flash plate闪熔镀层anchor bolt 地脚螺栓expansion bolt伸缩栓, 扩开螺栓shim plate 垫板push button station按钮式控制站logic diagram逻辑图calculation sheet计算书flow instrument流量计level instrument 位面计, 水平仪layout drawing 布置图tie band捆扎用带材Heating boxes加热室cutting opening切孔control valve actuator 阀控传动机构air set空气中凝固, 常温自硬自然硬化solenoid valve.螺线管阀,电磁阀calorimeter热量计odometer历程标tachometer转速计chronometer精密计时表Piping work: 铺管工程Steam trace: 加热蒸汽管道Cutting: 切割socket weld承插焊接fillet weld角焊,填角焊branch connection分支接续fabrication tolerance.制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding.密封焊接flange joint 凸缘接头undercut 底切feeder馈电线conduit outlet电线引出口seal fitting 密封接头, 密封配件Screw thread lubricant螺纹润滑剂Seal: 绝缘层weld reinforcement 焊缝补强lock washer 锁紧[止动, 防松]垫圈electrical panel.配电板,配电盘nipple螺纹接头zinc plated.镀锌的ring joint 环接, 围缘接合。
机械类专业词汇中英文对照翻译表大全
机械类专业词汇中英文对照翻译表大全机械类专业词汇表一画一字螺丝批slot type screwdriver 一点透视 one-point perspective 二画二合一黏合剂 epoxy resin adhesive 二合胶；混合胶 epoxy glue 二维的；平面的 two-dimensional 二进制 binary 二极管；整流子 diode 二号螺丝攻 second tap 二路开关 two-way switch 十进制的；公制的 metric 人工制品 artefact 人造板 man-made board 人体工程学ergonomics 。
human engineering 人体尺寸 human dimension 人体测量学anthropometry 。
anthropometrics 刀片 blade 刀身 blade 刀具 tool 刀具溜座 carriage 刀柱 tool post 刀架 tool rest 刀架底座 tool rest bracket 刀座帷；床鞍 apron 刀座鞍；溜板座 saddle 力 force 力三角形 triangle of force力平行四边形 parallelogram of force 力多边形；多边形力学 polygon of force 力的分解 force resolution 力架；亮漆 lacquer 力矩 moment 力偶couple 力矩定律 law of moment 力-距离图表 force-distance graph 力图 force diagram 力线 line of force 力点 effort 十字榫 cross halving joint 十字螺丝 Philip's head screw 十字螺丝批 Philip's type screwdriver 丁字尺； T 尺 tee square 三画三爪夹头 three-jaw chuck 三角尺 set square 三角形结构系杆 triangulation tie 三角锉 triangular file 三维的；立体的 three-dimensional 三氯甲烷；哥罗芳chloroform 三聚氰 ?胺；蜜胺 melamine 三点透视three-point perspective 上油漆 painting 上釉enamelling 凡立水 varnish 叉形顶尖 fork centre 口罩 mask 士力；虫漆 shellac 士巴拿；扳手 spanner 大芯夹板；宽条芯夹板 blockboard 。
常用机械专业术语中英文对照
常用机械专业术语中英文对照阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter 齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation ; creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism 减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel联组V 带tight-up V belt联轴器coupling ; shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design ; design for environment马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion ;wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham‘s coupling 矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing松边slack-side顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation 速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding motion弹性联轴器elastic coupling ; flexible coupling弹性套柱销联轴器rubber-cushioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form特殊运动链special kinematic chain特性characteristics替代机构equivalent mechanism调节modulation, regulation调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing调心轴承self-aligning bearing调速speed governing调速电动机adjustable speed motors调速系统speed control system调压调速variable voltage control调速器regulator, governor铁磁流体密封ferrofluid seal停车阶段stopping phase停歇dwell同步带synchronous belt同步带传动synchronous belt drive凸的，凸面体convex凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling外齿轮external gear弯曲应力beading stress弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement位移曲线displacement diagram位姿pose , position and orientation稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism 蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite系杆crank arm, planet carrier现场平衡field balancing向心轴承radial bearing向心力centripetal force /离心力centrifugal force相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion 修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear谐波传动harmonic driving谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism 虚拟现实virtual reality虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; permissible stress悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism一般化运动链generalized kinematic chain移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration应力图stress diagram应力—应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion 预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring 圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation运动粘度kenematic viscosity载荷load载荷—变形曲线load—deformation curve载荷—变形图load—deformation diagram窄V 带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator 直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact周节pitch周期性速度波动periodic speed fluctuation周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load轴向基本额定动载荷basic dynamic axial load rating轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair转速swiveling speed ; rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear 锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work 纵向重合度overlap contact ratio纵坐标ordinate组合机构combined mechanism最少齿数minimum teeth number最小向径minimum radius作用力applied force坐标系coordinate frame。
常用机械专业术语中英文对照
常用机械专业术语中英文对照机械工程是一个涵盖广泛的领域，其中包含了许多复杂的专业术语。
对于学习和工作在机械领域的人而言，掌握这些术语是非常重要的。
在此，我们将通过对常用机械专业术语的中英文对照进行分析和解释，为您提供帮助。
1. 传动系统：Transmission system2. 机械零件：Mechanical parts3. 摩擦力：Friction force4. 机械加工：Mechanical processing5. 各向同性：Isotropy6. 焊接：Welding7. 机械设计：Mechanical design8. 电机：Electric motor9. 压力传感器：Pressure sensor10. 材料力学：Material mechanics11. 钢铁材料：Steel materials12. 运动控制：Motion control13. 热处理：Heat treatment14. 机械系统：Mechanical system15. 变形：Deformation16. 自适应控制：Adaptive control17. 流体力学：Fluid mechanics18. 微机电系统：Micro-electromechanical systems19. 工业机器人：Industrial robot20. CNC加工：CNC machining以上就是常用机械专业术语的中英文对照。
这些术语是机械领域中非常重要的一部分，他们涵盖了机械材料、流体力学、控制系统和加工过程等领域。
对于机械工程师来说，能够正确地使用这些术语可以帮助他们更好地理解机械原理和操作方法。
此外，在不同的国家和地区，机械专业术语的使用可能会有所不同。
因此，在国际贸易和国际交流中，了解各种语言和文化的机械术语是非常有益的。
最后，学习这些机械专业术语需要具备一定的专业知识和背景知识。
因此，如果您想要更深入地了解机械领域，我们建议您课程或学习机械工程相关的教材。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
磁路 magnetic circles
变压器 transformer
异步电动机 asynchronous motor
几何形状 geometrical
精度 precision
正弦形的 sinusoid
交流电路 AC circuit
机械加工余量 machining allowance
斜齿圆柱齿轮 helical-spur gear
直齿锥齿轮 straight bevel gear
运动简图 kinematic sketch
齿轮齿条 pinion and rack
蜗杆蜗轮 worm and worm gear
虚约束 passive constraint
车刀 lathe tool
车床 lathe
钻削 镗削 bore
车削 turning
磨床 grinder
基准 benchmark
钳工 locksmith
锻 forge
压模 stamping
焊 weld
拉床 broaching machine
疲劳极限 fatigue limit
断裂 fracture
塑性变形 plastic distortion
脆性材料 brittleness material
刚度准则 rigidity criterion
垫圈 washer
垫片 spacer
直齿圆柱齿轮 straight toothed spur gear
可编程序逻辑控制器 Programmable Logic Controller PLC
电火花加工 electric spark machining
电火花线切割加工 electrical discharge wire - cutting
相图 phase diagram
热处理 heat treatment
粗加工 rough machining
变速箱体 gearbox casing
腐蚀 rust
氧化 oxidation
磨损 wear
耐用度 durability
随机信号 random signal
离散信号 discrete signal
超声传感器 ultrasonic sensor
联结 link
传动 drive/transmission
轴 shaft
弹性 elasticity
频率特性 frequency characteristic
误差 error
响应 response
定位 allocation
机床夹具 jig
动力学 dynamic
载荷 load
应力 stress
安全系数 safty factor
可靠性 reliabili
ty
螺纹 thread
螺旋 helix
键 spline
销 pin
内圆磨削 internal grinding
平面磨削 plane grinding
变速箱 gearbox
离合器 clutch
绞孔 fraising
绞刀 reamer
螺纹加工 thread processing
螺钉 screw
铣削 mill
铣刀 milling cutter
动量 momentum
桁架 truss
轴线 axes
余子式 cofactor
逻辑电路 logic circuit
触发器 flip-flop
脉冲波形 pulse shape
数模 digital analogy
液压传动机构 fluid drive mechanism
求导 derivation
定积分 definite integral
不定积分 indefinite integral
曲率 curvature
偏微分 partial differential
伺服电机 actuating motor
铣床 milling machine
钻床 drill machine
镗床 boring machine
步进电机 stepper motor
丝杠 screw rod
导轨 lead rail
组件 subassembly
功率 power
工件 workpiece
齿轮加工 gear mechining
齿轮 gear
主运动 main movement
主运动方向 direction of main movement
进给方向 direction of feed
进给运动 feed movement
零件图 part drawing
装配图 assembly drawing
尺寸标注 size marking
技术要求 technical requirements
刚度 rigidity
内力 internal force
位移 displacement
截面 section
拉孔 broaching
装配 assembling
铸造 found
流体动力学 fluid dynamics
流体力学 fluid mechanics
加工 machining
液压 hydraulic pressure
切线 tangent
机电一体化 mechanotronics mechanical-electrical integration
悬架 suspension
转向器 redirector
变速器 speed changer
板料冲压 sheet metal parts
孔加工 spot facing machining
车间 workshop
工程技术人员 engineer
气动夹紧 pneuma lock
机械零件 mechanical parts
淬火冷却 quench
随机变量 random variable
排列组合 permutation and combination
气体状态方程 equation of state of gas
动能 kinetic energy
势能 potential energy
机械能守恒 conservation of mechanical energy
热加工 hotwork
摄像头 CCD camera
倒角 rounding cham来自er 优化设计 optimal design
工业造型设计 industrial moulding design
有限元 finite element
滚齿 hobbing
插齿 gear shaping
变形力 deforming force
变形 deformation
应力 stress
硬度 rigidity
热处理 heat treatment
退火 anneal
正火 normalizing
脱碳 decarburization
渗碳 carburization
运动学 kinematic
静力学 static
分析力学 analyse mechanics
拉伸 pulling
压缩 hitting
剪切 shear
扭转 twist
弯曲应力 bending stress
强度 intensity
三相交流电 three-phase AC
机械专业英语词汇（很全）
金属切削 metal cutting
机床 machine tool
金属工艺学 technology of metals
刀具 cutter
摩擦 friction
曲柄 crank
摇杆 racker
凸轮 cams
共轭曲线 conjugate curve
范成法 generation method
定义域 definitional domain
值域 range
导数\\微分 differential coefficient
滚动轴承 rolling bearing
滑动轴承 sliding bearing
弹簧 spring
制动器 arrester brake
十字结联轴节 crosshead
联轴器 coupling
链 chain
皮带 strap
精加工 finish machining
合成进给运动 resultant movement of feed
合成切削运动 resultant movement of cutting
合成切削运动方向 direction of resultant movement of cutting
切削深度 cutting depth
电路 circuit
半导体元件 semiconductor element
反馈 feedback
发生器 generator
直流电源 DC electrical source
门电路 gate circuit
逻辑代数 logic algebra
外圆磨削 external grinding
集成电路 integrate circuit
挡板 orifice plate
残余应力 residual stress