电子有限公司产品样品规格书

（一）OPTO-ELECTRONICS(產品光-電參數):

(二)Shape Dimensions(產品外形尺寸):

Unit：mm Product Description產品描述：

(三)Electrical & Optical Curves-Spectrum （光&電參數曲線）：

Spectral Energy Distribution （R 、G 、B 、Y 、W ）

IF －IV Curve （R 、G 、B 、Y 、W ） I F －lm/w Curve （R 、G 、B 、Y 、W ） Forward Voltage —Forward Current Curve （R 、G 、B 、Y 、W ）

Light intensity distribution Light Output Characteristics of Tj

Room Temperature Operating Life Reliability Test Result

常温点亮信赖性结果

(Ta=25o C,If=700mA ）Use SSC circuit board&heat sink(Tj=50o C)

使用SSC 带热沉电路板(Tj=50o C)

0.20.40.60.811.2

128

256

384

512

640

768

896

1024

使用结温在60°度的使用以下，1000HR 2％ degradation(1000小时衰减2%)

Life Time graph (使用寿命)

使用结温在60°度的使用以下，50000HR 50％ degradation (50000小时衰减50%)

使 用 说 明

一、为避免吸潮建议将产品贮存在放有干燥剂的干燥柜中，贮存温度为：5℃~30℃，湿度：≤60%HR 。 二、贮存在温度较高环境的产品使用前，建议干燥，干燥条件为：100℃±5℃/12个小时。 三、产品在焊锡后冷却过程中避免机械压力和过大震动。 四、回焊后不允许快速冷却。

Relative Luminous Output[%]

Time[Hr]

五、禁止焊接在变形PCB板上。

六、产品不得接触水、油、有机溶液。

七、产品使用最大温度值应考虑工作电流大小。

八、打开防潮包装后7天内产品使用完毕。

九、重新包装未使用的产品置防潮袋密封好之后贮存在干燥的地方。

十、产品外观尺寸可更改而不另行通知。

十一、防静电要求：使用产品时，必须戴防静电环或防静电手套，所有设备、装置、机台必须有效接地。十二、该产品必须配置恒流源驱动。

(1)In order to aviod absorption of moisture it is recommended that the products are stored inthe dry

box (or dessicator ) with a dessicant.Alternatively the following environment is recommended:

Storage temperature :5°C~30°C Humidity:60% HR max.

(2) Storage in high humidity

If the storage conditions are of high humidity the product should be dried befor use.

Recommended drying conditions: 12 hours at 100°C±5°C

(3) Any mechanical force or any excess vibration should be avoied during the cooling

process after soldering.

(4) Reflow Rapid cooling should be avoided.

(5) Components should not be mounted on distorted Printed Circuit Boards.

(6) Devices should not be used in any type of fluid such as water,oil,organic solvents etc.

When cleaning is required,IPA should be used.

(7) The maximum ambient temperature should be taken into consideration when determining

the operating current.

(8) Devices should be soldered within 7 days after opening the moisture-proof packing.

(9) Repack unused product in anti-moisture packing,fold to close any opening and store in a dry place.

(10) The appearance and specifications of devices may be modified for improvement without notice.

(11) ESD Precautions.Static Electricity and surge damages LEDs.

It is recommended that wrist bands or anti-electrostatic gloves be used when handing the

LEDs.All devices,equipment and machinery should be properly grounded.

(12) This product must bedriven by costant power supplier.